IP-100维修手册(英文)1

6HUYLFH 0DQXDO
EPSON IP-100
®
SEIJ98009
PRECAUTIONS
There are cautionary notes throughout the text to help you avoid personal injury or equipment damage.
Signals a precaution which, if ignored, could result C A U Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution in damage to equipment.
should be exercised in performing procedures
preceded by a WARNING heading.
Always observe the measures listed below when performing repair or maintenance procedures.
WARNING
1.Always disconnect the product from both the power source and host computer before performing any maintenance or repair procedure.
2.No work should be performed on the unit by persons unfamiliar with basic safety measures dictated for all electronics technicians in their line
of work.
3.In performing testing described in this manual, do not connect the unit to a power source until instructed to do so. When the power supply
cable must be connected, use extreme caution in working on the power supply and other electronic components.
CAUTION
1.Repairs on EPSON products should be performed only by an EPSON-certified repair technician.
2.Make certain that the source voltage is the same as the rated voltage listed on the serial number/rating plate. If the EPSON product has a
primary AC rating different from the available power source, do not connect it to the power source.
3.Always verify that the EPSON product has been disconnected from the power source before removing or replacing printed circuit boards
and/or individual chips.
4.To protect sensitive microprocessors and circuitry, use static discharge equipment, such as anti-static wrist straps, when accessing
internal components.
5.Replace malfunctioning components only with those components recommended by the manufacturer; introduction of second-source ICs or
other nonapproved components may damage the product and void any applicable EPSON warranty.
Revision Status
Table of Contents
Product Description
Features (7)
Basic Specification (8)
Print Specification (8)
Character Specification (8)
Control Code (8)
Feeding Method (8)
Paper Specification (8)
Printable Area (10)
Adjust Lever (11)
Ink Cartridge Specification (11)
Environmental Condition (12)
Electrical Specification (13)
External Dimensions and Weight (14)
Reliability (14)
Interface (15)
Parallel Interface (15)
Serial Interface (17)
Operation when the receiving buffer is full (18)
Interface Selection (18)
Printer Control Panel (19)
Indicator (19)
Switch Function (19)
LED Operation (20)
Error Conditions (21)
Ink Out (21)
Paper Out (21)
Paper Jam (21)
No Cartridge (21)
Maintenance Request (21)
Fatal Error (21)
Initialization (22)
Initialization Settings (22)
Main Component ........................................................................................... 22 Control Panel (23)
Switch (23)
Indicator (23)
LCD (24)
Printer Operating Switches (26)
PCMCIA Type II Slot (26)
Volume Switch (26)
Input Selector Switch (26)
Outline of Basic Functions (27)
Easy Print Functions (27)
Copy Functions (27)
Outline of Printing Condition Settings (27)
Outline of the Special Filters (28)
Maintenance Functions (28)
Details of Functions (29)
Printing Functions (29)
Start Printing (33)
Setting Printing Conditions (34)
Setting the Special Filters (40)
Setting the Maintenance Functions (46)
Error Code List (47)
Functional Sound List (48)
Voice Guide (48)
Voice Guide List (48)
Voice Guide Segment List (49)
Timing for Functional sound and Voice Guide Generation (49)
Functional Sound and Voice Guide Timing when an Error Occurs (50)
Other Functional Sound and Voice Guide Timings (51)
Printing Allocation Sequence for each Layout (52)
Supported Image File Formats (55)
List of Supported Digital Still Camera (56)
List of Supported Memory Cards (57)
List of Relevant Application Software (57)
List of Print Format Dimensions (58)
Operating Principles
Overview (60)
Electric Circuit Operating Principles (60)
C266 PSB Power Supply Board (60)
C266 Main Board (61)
Troubleshooting
Troubleshooting (63)
Disassembly and Assembly
Disassembly (65)
C266 Main Board and Control Panel A Removal (65)
Housing Removal (67)
Speaker Removal (67)
Adjustment
Overview (69)
Adjustment Item (69)
Adjustment Tool (69)
Adjustment (70)
Procedure up to initialize the service program (70)
Maintenance
Maintenance (73)
Appendix
Connector Connection (75)
Connector (75)
Component Layout (78)
Circuit Diagram (80)
Parts List (81)
Exploded Diagram (86)
& +4$37( 5 PRODUCT DESCRIPTION
1.1 Features
Major features of IP-100 are as follows.
†Stand-alone photo print function
… A memory card can be mounted directly to allow the printing of an image file without the use of a personal computer.
… A simple operation environment provided with a special GUI operation panel.
… A special built-in image processing module enables high-speed print processing.
†Functions for setting up the various printing conditions to recognize photograph printing.
…Index printing function
…Allows the use of mini-photo sticker and photo card paper
… A variety of effect functions for image processing
…Sticker printing with the use of the effect function
†Interface support for use as a PC printer
…IEEE1284 parallel I/F
…Mac serial I/F
†High-quality color printing based on the EPSON Stylus Photo 700.
…High-speed 720 dpi high-quality Bi-D printing
…High-quality photograph printing with the use of photo mach technology
…High-quality printing with micro weave processing
…High-resolution 1440 x 720 dpi printing with the use of super microdot technology
Table 1-1. Consumable items and options
NOTE: Refer to Table 1-3 on page 9 for paper types.
1.2 Basic Specification
1.2.1 Print Specification
† Print Method: Ink-jet
† Nozzle configuration:Black 32 nozzle
Color 32 nozzle/ color
(Cyan, Magenta, Yellow, Light Cyan, Light Magenta) † Print direction; Bi-directional printing (with logical seeking)
†Print speed and printable columns:
<Alphanumeric Character>
Quality:LQ
Character pitch: 10 pitch
Printable columns: 80
Print speed: 200 CPS
<Graphics Mode>
Table 1-2. Print Speed/ Printable dot/Printable area
1.2.2 Character Specification
† Character Tables: PC437 (US, Standard Europe)
PC850 (Multilingual)
† Type face:EPSON Courier 1.2.3 Control Code
† ESC/P Raster
1.2.4 Feeding Method
† Feeding method:Friction feed with ASF
† Line spacing:1/6 inch or programmable at 1/360 inch
† Feeding speed: 2.36 inch/sec (Continuous)
† Paper insert:164.6ms (9.03mm paper feed)
1.2.5 Paper Specification
1.2.5.1 Relevant Paper
† Paper Size: A6 (105mm x 148mm)
4x6 photo card (113.6mm x 175.4 mm)
A4 (210mm x 297 mm)
† Supported paper type: Photo paper (special super-fine glossy)Ink
Jet paper
Normal paper
NOTE:Special glossy film is only supported with mini-photo sticker paper.
The special paper supported by IP-100 is as follows.
Table 1-4. Paper Type
Table 1-3. Paper Type
NOTE:Not curled, wrinkled, scuffing or torn paper be used.
Perform printing under the room temperature.
The availability of special media varies by country.
1.2.6 Printable Area
Table 1-5. Printable Area
NOTE: See the figure (figure 1-1) on your right.
P W
L M R M
T M
P r in t a b le a r e
P
a
L
B M
Figure 1-1. Printable Area
1.2.7 Adjust Lever
Table 1-6. Adjust Lever Position and Paper Type
Figure 1-2. Adjust Lever 1.2.8 Ink Cartridge Specification
1.2.8.1 Ink Cartridge (Black)
† Type: Exclusive cartridge
† Color: Black
† Ink Life: 540 pages/A4 (ISO/IEC10561 Letter Pattern at 360 dpi)
† Validity: 2 years from production data (sealed in package, out of
package)
† Environmental condition (Temperature)
… Transit: - 30︒C ~ 60︒C (within120 hours at 60︒C and within a month at 40 ︒C)
…Storage: -20 ︒C ~ 40 ︒C (within a month at 40 ︒C)
…Packing storage: -30 ︒C ~ 40 ︒C (within a month at 40 ︒C)
†Dimension: 19.8mm (W) x 52.7mm (D) x 38.5mm (H)
†Weight:54g
Figure 1-3. Ink Cartridge (Black)
1.2.8.2 Ink Cartridge (Color)
Exclusive cartridge
Magenta, Cyan, Yellow, Light Magenta, Light Cyan 220 pages/A4 ( at 360 dpi, each color 5%) 2 years from production data (sealed in package, out of package)
† Environmental condition (Temperature)
… Transit: - 30 ︒C ~ 60 ︒C (within120 hours at 60 ︒C and within a month at 40 ︒C)
… Storage: -20 ︒C ~ 40 ︒C (within a month at 40 ︒C)
… Packing storage: -30 ︒C ~ 40 ︒C (within a month at 40 ︒C)
† Dimension: 51.4mm (W) x 52.7mm (D) x 38.5mm (H)
† Weight:85g
1.2.9 Environmental Condition
† Temperature:
… During Operations:
10 ︒C ~ 35 ︒C … During storage:
-20 ︒C ~ 40 ︒C
…
During Transportation: -20 ︒C ~ 60 ︒C
NOTE: Less than one month at 40 ︒C and less than 120 hours at 60 ︒C.
† Humidity:
… During operations: 20% to 80% (with no condensation) … During storage:
20% to 85% (with no condensation)
…
During transportation: 5% to 85% (with no condensation)
NOTE: Although within the range of the chart shown below.
H u m i d it y ( % )
Y e llo w
( Y )
L ig h t M a g e n t a ( L M )
T epemr a(°t)Cu r e
C y a n
( C )
( M )
M a g e n t a
Figure 1-5. Temperature/Humidity Range
L ig h t
C y a n ( L C )
Figure 1-4. Ink Cartridge (Color)
†
Type: † Color: † Ink Life: † Validity:
† Vibration endurance:
…During operations: 0.15G, 10Hz to 55Hz. X, Y, Z directions …During storage: 0.50G, 10Hz to 55Hz. X, Y, Z directions † Impact endurance:
…During operations: 1G, 1ms or less. X, Y, Z directions
…During storage: 2G, 2ms or less. X, Y, Z directions NOTE: 1. Confirm that the printing head is capped when being stored.
2.Confirm that the printing head is capped and that the ink
cartridge is mounted in the printer when being transported.
3.If the printing head is not capped when the power supply is off,
switch the power on with the ink cartridge set in place, cap the
printing head and then switch the power off again.
4.The ink inside the printing head and in the ink cartridge will
freeze if the unit is stored in an environment with a temperature
of -4︒C or less. The unit must be left to stand for approximately
three hours in an environment with a temperature of 25︒C in
order to allow the frozen ink to be used again. 1.2.10 Electrical Specification
AC220-240V power unit specification for China and Hong Konng.
Table 1-7. Electric Specification
See “NOTE” on next page.
AC110V Power unit specifications for Taiwan. Table 1-8. Electric Specification
1.2.11 External Dimensions and Weight
† Width:
447mm
† Height:
180mm (from the installed surface to the IP-100 operation panel) (Including the 286mm paper support)
† Depth: 267mm (from the printer operation panel to the ASF frame)
(Including the 601mm paper support and sticker) † Weight:
Approximately 6.4Kg
NOTE: Measurement conditions for the average amount of electricity
consumed during continual printing (not mentioned in the catalogue or manual)
Printing mode: One frame (or full photograph) Paper type: Photo printing paper (glossy paper)
Paper size: A6 Layout: One surface layout 4 7 7 m m
2 8 6 m m
2 6 7 m m 6 0 1 m m
Photograph size: L
Photo No.: 1 (image:01010004.jpg)
Copies: User defined Quality: High
Enhancement: ON Frame: None Filter: None
Figure 1-6. Exterior View 1.2.12 Reliability
† Total printing capability: 10,000 pages (A4)
† Life expectancy of the print head:2 billion dots (at the nozzle)
1.3 Interface
1.3.1 Parallel Interface
1.3.1.1 Forward Channel
† Transmission mode: 8 bit parallel
† Synchronization: By STROBE pulse
† Handshaking: By BUSY and /ACKNLG signal
† Signal level: TTL compatible level
† Adaptable connector: 36-pin of 57-30360 (amphenol) or equivalent *It is recommended to use the interface cable as short as you need. When using these signals, the twist pair line should be used and the return side should be connected to the signal ground.
Table 1-9. Signals at Parallel I/F forward channel
Table 1-10. Signals at Parallel I/F forward channel NOTE: 1.Return side means twist pair return and is connected to the signal ground level. Also, each signal regarting to the interface
should use the twist pair wire line and the return side also
should be connected. Also, this cable is shielded wire and it is
effective to connect to each chassis GND in the center
machine and printer for electrostatic noise.
2.Conditions for interface are based on TTL level. Rise and
fall time should be within 0.2 μS.
3.Refer to the figure 1-7 for transmission timing of each signal.
4.Do not perform data transmitting ignoring /ACKNLG or BUSY
signals. (The data transmission to the printer must be performed
after confirming that /ACKNLG or when the BUSY signal is low.)
5.It is possible to perform the printing test including interface circuit
without using equipment from outside when 8-bit data signal is
set to appropriate word code and connect then forcefully to
/ACKNLG and /STROBE. However, it is necessary to set the
Parallel I/F mode in the EEPROM “Normal”.
D A T A
t
t t s t b
B U S
Y
t
t re a d t byu s y
/ A C K N L G t re p l y t a c k t n b u s y
Figure 1-7. Parallel Interface Timing Chart
Table 1-11. Timing Chart
*1: Rise and fall time of every output signals.
*2: Rise and fall time of every input signals.
Typical time of tack is shown below.
b y t e n + 1
Table 1-12. Typical Time of Tack
1.3.1.2 Reverse Channel
† Transmission mode: IEEE-1284 nibble mode
† Synchronization: Refer to the IEEE-1284 specification † Handshaking: Refer to the IEEE-1284 specification † Logic(signal) level:
IEEE-1284 level 1 device
TTL compatible level
† Data trans. timing: Refer to the IEEE-1284 specification
† Extensibility request:
The printer responds affirmatively when the
extensibility request values are 00H or 04H, that means,
00H: Request Nibble Mode Reverse Channel
Transfer. 04H: Request device ID;Return data using
nibble mode Reverse Channel Transfer.
† Device ID: <00H> <43H>
MFG:EPSON;
CMD:ESCPL2, BDC; MDL:PT-100;
CLS:PRINER;
DES:EPSON[SP]PT-100;
Table 1-13. Signal at Parallel I/F Reverse Channel
1.3.2 Serial Interface
† Data Transmission Type: Based on RS-423 † Synchronization: Synchronous
† Data Transfer Speed: 1.8 Mbps (Max.) † Data Format:
Start bit 1 bit
Data length 8-bit Parity bit None
Stop bit
1 bit
† Handshaking: DTR control, Xon/Xoff control † Adaptable Connector:
8-pin Mini DIN
† Recommended Interface Cable: Apple system peripheral-8cable
Table 1-14. Input connector signal
8 7 6
5 4 3
2 1
Figure 1-8. Serial Interface Connector Port
Table 1-15. DTR, Xon/Xoff handshaking timing
1.3.3 Operation when the receiving buffer is full Generally, hosts abandons data transfer to peripherals when a peripheral is in the busy state for dozens of seconds continuously. To prevent this kind of time-out, the printer receives data very slowly, several bytes per minute, even if the printer is in busy state. This slow down is started when the rest of the input buffer becomes several hundreds of bytes. Finally, the printer is in the busy state continuously when the input buffer is full. 1.3.4 Interface Selection
IP-100 has 2 built-in interfaces; the parallel interface and serial interface. These interfaces are selected automatically.
†Automatic selection
After the power is turned on, the interface that receives data first is
selected. When the host stops data transfer and the printer is in the
stand-by state for the seconds (about 10 seconds), the printer is returned to the idle state. Then, I/F which receive the data next time is selected.
†Interface state and interface selection
…When the parallel interface is not selected, the interface gets into the busy state.
…When the serial interface is not selected, the interface set the DTR signal MARK(HIGH).
…When the printer is initialized or returned to the idle state(no I/F is selected), the parallel interface gets into the ready state, the serial
interface sets the DTR signal SPACE (LOW).
…Caution that the interrupt signal such as the -INIT signal on the parallel interface is not effective while that interface is not selected.
1.4 Printer Control Panel
1.4.1 Indicator
4 3
2
1
B la c k inP ak p e r P o w e r
C o lo r
c h e c k
in k
I n k P a p e r
m a in t e fneaendc/ee je c t
Table 1-17. Function at power on
Turn on the power pressing “Paper Feed/Eject” switch and “Ink
Maintenance ”, then, press “Paper Feed/Eject” switch while the Paper -End LED is blinking (about 3 seconds).
<Special Setting Mode>
Figure 1-9. Printer Control Panel
1:Power Green
2:Paper check: Red
3:Ink end (black): Red
4:Ink end (color): Red
1.4.2 Switch Function
Table 1-16. Functions at the normal state
1.4.3 LED Operation
Table 1-18. LED Indication
NOTE: “1*”:Refer to Section 1.5 Error conditions.
“---” in the table means no change.
1.5 Error Conditions
This printer goes to the error condition when the following conditions are detected. When the printer is in the error condition, data input is stopped by setting the /ERROR signal as “LOW” and BUSY signal as “HIGH”. At this time, the printer will not be able to print automatically.
1.5.1 Ink Out
†Detects both monochrome and color ink end.
†When it gets close to the end of ink, the printer indicates by the indicator.
When the ink runs out, the printer indicates “Ink Out” and stops. In case of color ink cartridge, if just one color runs out, the printer goes to the
error condition.
It is prohibited to use the ink cartridge which is once taken out of the printer. (Be careful when performing the repair service or
checking)
1.5.2 Paper Out
†The printer goes to this error condition when the printer tries to feed
a paper but there is no paper.
1.5.3 Paper Jam
†The printer goes to this error condition, when the paper is not ejected at power on by the regular paper eject operation of the standard steps,or by FF command or Feed/Eject switch.
1.5.4 No Cartridge
†The printer goes to this error when the ink cartridge is not installed or comes off.1.5.5 Maintenance Request
†When the ink waste liquid reaches the certain amount, the printer indicates this error and stops. The printer does not recover from this error until the ink absorber (pad) is replaced and a waste ink counter is reset.
1.5.6 Fatal Error
†This printer goes to this error when carriage control error and character generator access error are detected.
NOTE: See Table on page 20 for indicator indication.
1.6 Initialization
IP-100 has three kinds of initialization methods.
†Hardware Initialization
This printer is initialized when the power is turned on. When the printer is initialized, following actions are performed.
1.Initializes printer mechanism
2.Clears input data buffer
3.Clears print buffer
4.Sets the default values
†Software Initialization
ESC @ command also initializes the printer. When the printer is initialized, following actions are performed.
1.Clears print buffer
2.Sets the default values
†Panel Initialization
The printer initialized when the printer is turned off one and is turned on again within 10 seconds, or when /INIT signal is input.
1.Caps the print head
2.Eject the paper
3.Clears input data buffer
4.Clears print buffer
5.Sets the default values 1.
6.1 Initialization Settings
IP-100 initializes following values when the initialization is performed. Default setting, panel setting and remote command setting, which are possible to be stored are initialized as default values.
…Page position: Present paper location as page heading position …Line spacing: 1/6 inch
… Right margin position: 80 lines
…Left margin position: first line
…Character pitch: 10 CPI
…Printing mode: Text mode (Not raster graphics mode)
1.7 Main Component
IP-100 has following major components.
†Printer Mechanism
†C233 Main Board
†C266 PSB Power Supply Board
†Control Panel (2029380)
†Printer Control Panel (2029381)
1.8 Control Panel
1.8.1 Switch
P
P l a i n P h o o t
e
A T y p e
P a p
e r
t
P a p e r
P
E
S i z e
4 x 6
A 4
R
F
I n d e x C r o p
O
S t ic k e r
R L a y o u t M a r k s
M
A
S i z e
C a r d
T
4 x E6
L
S
F r o m
E P h o t o A ll
C a m e r a
L E f f e · c ·t · N o .
E
F r a m · e · ·N o .T o
C C o p i e s
·N ·o · · ·C o p i e s
T
S e .t
S Q u a l it y
9
E
O n O f f
1 0
E n h a n c e m e n t
7
M e n u s C h a n g e S e t t in g s
8
1 7
1 5 5 1 3
3
4
F r a m Feilt e r
1 8
1 1
1 2
1 6
C a n c e l
S e le c t r o c e
i n g 2
. . .
P h o t o
O n e R a n g e
1 9 Q u ic k S e le c t
6
S t a r t 1
I n d e xA l l
P r i n t
1 4
Figure 1-10. Switch Location
1.8.2 Indicator
Table 1-20. Indicator Color
1.8.3 LCD
Table 1-21. Description of Indicator
1.8.3.1 Panel Description
Index mode
Index
On
E P S O N
E P S O N
Draft index mode
Flashing A
A P
T y p e
P h o t So u p e Pr l a
P
P a p e Mr a t t Pe a p
One Frame mode One On R E
S i z e
A 6
4 x 6 A 4
All Photo mode
On
All
Camera mode Flashing A F
I n d e x
C r o p
S t ic k e r
Range mode
Range
On
R O
L a y o u t
M a r k s
M
Frame function on
On
A S i z e 4
Frame
T Setting frame function
Flashing A
S P h o t o
N o . F r o
E
· · ·
P h o t A o ll N o .
Filter function on
On
N o .
Filter
E f f e c t
E
F r a m e
N o . T o
Setting effect function
Flashing A C C o p i e s
· · ·
T
· · · · · ·
S e t N o .
C o p i
Detailed settings
Frame + Filter
Flashing A
S Q u a l i H t ig y
hD r aSfut p e r
Adjusting printer
Index + All
Flashing A
E
O n
O f f
T
E n h a n c e m e n t
Printing
Flashing B
Figure 1-11. Hong Kong model LCD Panel
Receiving print request
Flashing C
Processing
NOTE: Figure above shows all segments lit.
Writing program ROM
Flashing D
(not available to user)
See Chinese and Taiwan model on next page.
Flashing A: Flashes at 0.5 s period, 50% duty Flashing B: Flashes at 1.0 s period, 50% duty
Flashing C: Flashes four times at 0.3 s period, 50% duty Flashing D: Flashes at 0.3 s period, 50% duty
Table 1-22. Description of Panel
Figure 1-13. Taiwan model LCD Panel Figure 1-12. Chinese model LCD Panel
NOTE: Figure above shows all segments lit.
NOTE: Figure above shows all segments lit.
Table 1-23. Description of Panel (Cont.)
1.8.4 Printer Operating Switches
Table 1-24. Printer operating switches
1.8.5 PCMCIA Type II Slot
Table 1-25. PCMCIA Type II Slot
1.8.6 Volume Switch
Table 1-26. Volume Switch
Name
(High)
(Low)
(Off)
1.8.7 Input Selector Switch
Table 1-27. Input Selector Switch
Name
1.9 Outline of Basic Functions
1.9.1 Easy Print Functions
When one of the basic operating modes is selected, printing can be started without setting the printing conditions just by pressing the Start Print switch. However, individual printing conditions can be set if more detailed settings are required.
ALL PHOTO MODE
Prints the designated number of copies of all photos stored in the memory card.
INDEX MODE
Prints the designated number of copies of all photos stored in the memory card as an index. In addition to the normal index mode, a draft index mode is available which gives priority to printing speed.
CAMERA MODE (DPOF)
Prints the photo preset at the camera. It is not necessary designate the photo number or number of copies at the printer. RANGE MODE
Prints a single copy of photos with consecutive photo numbers in a designated range in the memory card.
1.9.3 Outline of Printing Condition Settings
Printing conditions such as print quality and print format can be selected at the LCD panel for each basic operating mode. With the exception of the paper settings (type and size), each set value is stored for each basic operating mode. (The printing conditions revert to the initial values when the power is turned off.)
1.9.3.1 Paper
PAPER TYPE
Select the type of paper for printing from photo paper, super matte paper, and plain paper. The selected paper type is displayed on the LCD panel. PAPER SIZE
Select the size of paper for printing from postcard (A6), 4x6, and A4.
The selected paper size is displayed on the LCD panel.
1.9.2 Copy Functions
When one of the basic operating modes is selected, at least the photo number printing condition must be designated before starting printing. However, individual printing conditions can be set if more detailed settings are required.
ONE FRAME MODE
Prints the designated number of copies of any one frame in the memory card. 1.9.3.2 Format
LAYOUT
Select the layout of the printed photo. The selected layout is displayed on the LCD panel.
PHOTO SIZE
The photo size is automatically determined from the designated paper size and layout of the printed photo. The photo size is displayed on the LCD panel.
1.9.3.3 Select
PHOTO NO.
Set the photos to print. During the selection operation, the photo numbers are displayed on the LCD panel.
COPIES
Set the number of copies of each photo to print. During the selection operation, the number of copies is displayed on the LCD panel.
1.9.3.4 Set
QUALITY
Select the printing quality from high, draft, and super-high quality. The selected quality is displayed on the LCD panel.
ENHANCEMENT
Designate whether enhancement is used. The enhancement ON/OFF setting is displayed on the LCD panel. 1.9.4 Outline of the Special Filters
FILTERS
Adjust the color and brightness of the printer photo.
FRAME
Synthesizes a separate prepared image on the printed photo (in Sticker, 16 format only)
DETAILED SETTINGS
Set the cropping tool, print start position offset, etc. (These settings
are retained when the power is turned off.)
1.9.5 Maintenance Functions
PRINTER ADJUSTMENT
This function adjusts the printer residual ink display and the printer head gap. ROM MANAGEMENT (NOT AVAILABLE TO USERS)
Displays the version of the current controller program and rewrites
the controller program flash ROM.
1.10 Details of Functions
This printer offers the following six basic operating modes.
O n e F r a m e R a n g e
D r a f t I n d e xC a m e r a
N o r m a l I n d eAxll P h o t o
Figure 1-14. Basic Operating Modes
The basic operating modes can be switched at any time by pressing the All, Index, One or Range switch.
NOTE:When a mode is selected, the corresponding LED indicator lights or flashes. (See Table 1-21 on page 24)
The All Photo mode is selected immediately after a memory card is inserted. However, the Camera mode is selected if the memory card contains a print designation file. If a print designation file exists in the memory card, press the All switch to alternate between the All Photo mode and Camera mode. Similarly, press the Index switch to alternate between the Draft Index mode and Index mode. (The Draft Index mode is selected initially.)
As the format (layout and size), select, and set (quality and enhancement) printing conditions are saved independently for each basic operating mode, the previous printing conditions are restored each time the basic operating mode is selected again. However, as the paper (type and size) printing conditions are common to all basic operating modes, the previous paper setting is not restored when a basic operating mode is selected again. NOTE:While setting the frame function, the Index switch operates to designate index printing of the frame data. 1.10.1 Printing Functions
1.10.1.1 All Photo Mode
† Appearance of the LCD Panel (Printing condition setting: initial setting)
P
P h o t o
A T y p e P a p e r
P
R
E
S i z e 4 x 6
F
O
R
L a y o t
M
A
T S i z e
S
E P h o t A o ll N o .
L
E
C C o p i s
C o p i
T
S Q u a lHi tigy h
E
E n h a n c e m e n t
T O n
…The photo No. displays the total number of photos contained in the memory card.
…The “All” indicator is lit.
†The following printing conditions can be set from the LCD panel:…Paper Type
…Paper Size
…Layout
…Copies (initial cursor position)
…Quality
…Enhancement。