NEC数字放映机二代机错误代码说明

Error Code of Series 2Error code Error message Description Checking point1Lamp Door Open Lamp door (cover) is open.1. Vefrify if the lamp door is closed and locked propely.2. 2. Is there any physical damage in the switch?3. Check the connection between POCO on COVER PWB and POCN3 on PJDIV PWB.2Lamp mp temperature is abnormal.1. Check the ambient temperature. It should be 35 degC or lower.2. Check if there is any problem on suction air and exhasut air.3. Check the air filter clogging.4. Check if the ventilation system is operated with required specification.5. Check the connection between Thermostud and POCN5 on PJDIV PWB.4GPSU(12V) Fail Power supply(12V) is abnormal.1. Check the DC power supply voltage.2. Check the connection between GPSU and POPSM on PJDIV PWB.5Lamp Unlit Lamp doesn’t light up.1. Check if the current bulb usage time is over limit. If yes, replace the bulb.2. Check loose screw connections on the igniter and cathode cable on the lamp holder.3. Check if the electric blackout was occured.4. Check if the operation to off the LPSU was occured.5. Check the connection between POCN2 on PJDIV PWB and PEDE-A PWB.6House OverTime Lamp house cumulative time is over. 1. Replace the reflector and reset lamp house usage hours.8LPSU OverTemp.Temperature (lamp power inside temperature) isabnormal.1. Check the ambient temperature. It should be 35 degC or lower.2. Check if there is any problem on suction air and exhasut air.3. Check the air filter clogging.4. Check if the ventilation system is operated with required specification.5. Replace the LPSU.12E2PROM R Fail(SYS:Param1 KEY:Param2DIV:Param3)E2PROM data read error is detected.Param 1/2/3:I2C: I2C errorCRC : CRC error1. Check CPU PWB/ PJDIV PWB/KEY I/O PWB.2. Check the cable between POIF on PJDIV PWB and KEY IO PWB.13Interlock Fail Interlock error is detected.1. Is there any problem in external control? (There is occasionally2. Check the connection between POIL on PEDE-A PWB and INTER PWB.3. Check the connection between POCI on PEDE-A PWB and POCN2 on PJDIV PWB.15E2PROM W Fail(SYS:Param1 KEY:Param2DIV:Param3)E2PROM data write error is detected.Param 1/2/3:I2C: I2C errorVfy : Verify error1. Check CPU PWB/ PJDIV PWB/KEY I/O PWB.2. Check the cable between POIF on PJDIV PWB and KEY IO PWB.17Pump Stop(Param1)Stopped for pump error.Param1: Rotating Speed(Decimal)1. Check the connection between POCN5 on PJDIV PWB and the pump.2. Check the 12v voltage to control the pump.3. Check the coolant unit.120DLP Ack Fail(Param1, Param2)ICP board failed the operation.Param1: 2nd portion of ICP command.Param2: 3rd portion of ICP command.ICP failed operation to the command, “CMD1,Param1, Pram2, …”.1. Check if the ICP version is the latest2. Launce the "Macro File Tools" to check if there are any problmes on ICP configurationfiles.3. Retry the projector operation.4. Reset the ICP board and retry the projector operation.5. Check the connection between FSB and MOTHER PWB.6. Check the power supply voltage for the ICP board121Lens Fail(Param1)(Param2, Param3)Lens unit control error (NC1200/NC2000)Param1: Detailed error information as followsEEPROM R/W FailV-Sensor Read FailH-Sensor Read FailComm Send FailComm Recv FailComm TimeoutRestart(In this case, no Param2/3)Param2/3: Lens unit control parameters.1. Check the connection between POCN2 on PJDIV PWB and MOTER I/F PWB.2. Replace the MOTOR I/F PWB.123Bulb OverTime Lamp bulb cumulative time is over.1. Check the usage time of lamp bulb and replace the lamp bulb.2. Verify that New Entry Bulb Setting was set when the lamp bulb was replaced.3. Replace CPU PWB.125LPSU Fail(Param1)LPSU Fail(Param1, Param2)LPSU communication error.LPSU is on abnormal status.Param1:“No Lamp” :Never communications with LPSUafter AC-ON.“Power”: Communication fail during regularLPSU status check.Communication error with LPSU occurs.Param1:Failed LPSU command codeParam2: Error type“ErrTx”, “ErrRx”, “Tout”, “ErrCmd”LPSU Fail(No Lamp):1. Check if the LPSU is powered on.2. Check the connection of RS-232C cable between PEDE-A PWB and LPSU.3. Check the connection between POCN2 on PJDIV PWB and PEDE-A PWB.LPSU Fail(Power):1. Power-cycle the LPSU. If prolbme is not gone, replace the LPSU.LPSU Fail(Param1, Param2):1. Check if the LPSU is powered on.2. Check the connection of RS-232C cable between PEDE-A PWB and LPSU.3. Check the connection between POCN2 on PJDIV PWB and PEDE-A PWB.128OutRange(Param1, Param2, Param3, Pram4)Adjusting lamp output value has set out of range.Param1: Caused operationLamp M: Manual adjustmentLamp D: Douser operationLamp FW: FeedBack(to keep watt) processLamp FB: FeedBack(to keep illuminance)processLamp LM: Lamp memory processParam2: Lamp current tried to set by projector(in 0.1A)Param3: Lamp current get from LPSU (in A)Param4: Lamp wattage get from LPSU (in W)1. The requested lamp output adjustment is out of range.129Down Lamp Power(Param1, Param2, Param3)Down lamp power to decrease set inside temperature.Param1: Measured point(Out/Intake/Exhaust/DMD-B)Param2: Temperature(in deg)Param3: Lamp outputLamp current (in 0.1A)1. Check the ambient temperature. It should be 35 degC or lower.2. Check if there is any problem on suction air and exhasut air.3. Check the air filter clogging.4. Check if the ventilation system is operated with required specification.130MMS Comm Fail(Param1:Param2:Param3)MMS communication error is detected.Param1: Failed MMS command codeParam2: Error type (“Con”, “Tx”, “Rx”, “Tout”)Param3: Error codee.g.) MMS Comm Fail(01:Tx02)1. Check the connection between MM3000B and Mother PWB.2.Check LAN connectors and LAN cable.3. Check power on of projector ( not stand-by mode ).131MMS Fan Stop Built-in MMS fan has stopped.1. Check fan cable cnnection.2. Replace FAN.In regard to MMS Fail, there are three types of errors as shown below.The respective methods of taking measures are described below.1) FPGA***This is a configuration error of FPGA. If the associated FPGA is of an input board, try to remount the board or check the flexible cable connections or reinstall the FPGA data.In the case of the other FPGA errors, also try to reinstall the FPGA data. Ifthis check is difficult to carry out, replace the associated board as a whole.2) Default DataThe data involved some deficiency at the time of shipment from the factory. Reinstall the data.3) User DataThis error is caused by a certain deficiency in the user data. As required,copy the user data in the PC so that checks can be made to see the elimination of the problem in the state that the default signal data are used after the execution of factory default. Since part of or all of the previously copied user data have been broken, reuse of these data is not recommendable. If the data are used for the purpose of setup data checks, theyshould be cleared later.133MM Reset (Command:Param1)Executed to reset Built-in MMSParam1: When executed to reset Built-in MMS.001: Executed to reset Built-in MMS when nocommunications between projectormain system and MMS.T-001: Executed to reset Built-in MMS when nocommunication between externalprojector and MMS.1. This message shows the projector reset the MM3000B because of no responses.If MMS Comm Fail occurs, see the MM3000B service manual.140DLP CommR Fail(Param1Param2Param3:Param4)Communication failure with the ICP board.(Communication I/F is RS-232C)Param1: First portion of ICP command.Param2: Second portion of ICP command.Param3: Third portion of ICP command.Param4: Error type (“Con”, “Tx”, Rxn”, “Nack”,“Tout”)e.g.) DLP CommR Fail(010203:Nak=0001H)ICP returns “NAK” response to the command, “01,02, 03, …”.1. If ICP is being updated by ICP & Enigma Control Program without "Special Mode",this message will be shown.2. If ICP is reset by ICP & Enigma Control Program, this message will be shown.3. Retry the projector operation.4. Reset the ICP board and retry the projector operation.5. Check the connection between FSB and MOTHER PWB.6. Check the power supply voltage for the ICP board.141DLP CommE Fail(Param1Param2Param3:Param4)Communication failure with the ICP board.(Communication I/F is Ethernet)Param1: First portion of ICP command.Param2: Second portion of ICP command.Param3: Third portion of ICP command.Param4: Error type (“Con”, “Tx”, Rxn”, “Nack”,“Tout”)e.g.) DLP CommR Fail(010203:Nak=0001H)ICP returns “NAK” response to the command, “01,02, 03, …”.1. If ICP is being updated by ICP & Enigma Control Program without "Special Mode",this message will be shown.2. If ICP is reset by ICP & Enigma Control Program, this message will be shown.3. Retry the projector operation.4. Reset the ICP board and retry the projector operation.5. Check the connection between FSB and MOTHER PWB.6. Check the power supply voltage for the ICP board.145SensorFail Outside Air(Param1)Sensor (Outside Air) read error.Param1: Get/SetFailed to get/set data from/to sensor board.146SensorFail LPSU Intake(Param1)Sensor (LPSU Intake) read error.Param1: Get/SetFailed to get/set data from/to sensor board.147SensorFail Exhaust(Param1)Sensor (Exhaust) read error.Param1: Get/SetFailed to get/set data from/to sensor board.148SensorFail DMD-B(Param1)Sensor (DMD-B) read error.Param1: Get/SetFailed to get/set data from/to sensor board.150Fan0 Stop(Param1)Fan0 has stopped.Param1: Rotating Speed(Decimal)1. Check the failed fan and replace failed fan.2. Check connector POCN5 on PJDIV PWB.For fan layout, see the appendix.151Fan1 Stop(Param1)Fan1 has stopped.Param1: Rotating Speed(Decimal)1. Check the failed fan and replace failed fan.2. Check connector POCN5 on PJDIV PWB.For fan layout, see the appendix.152Fan2 Stop(Param1)Fan2 has stopped.Param1: Rotating Speed(Decimal)1. Check the failed fan and replace failed fan.2. Check connector POCN5 on PJDIV PWB.For fan layout, see the appendix.153Fan3 Stop(Param1)Fan3 has stopped.Param1: Rotating Speed(Decimal)1. Check the failed fan and replace failed fan.2. Check connector POCN5 on PJDIV PWB.For fan layout, see the appendix.154Fan4 Stop(Param1)Fan4 has stopped.Param1: Rotating Speed(Decimal)1. Check the failed fan and replace failed fan.2. Check connector POCN5 on PJDIV PWB.For fan layout, see the appendix.155Fan5 Stop(Param1)Fan5 has stopped.Param1: Rotating Speed(Decimal)1. Check the failed fan and replace failed fan.2. Check connector POCN5 on PJDIV PWB.For fan layout, see the appendix.156Fan6 Stop(Param1)Fan6 has stopped.Param1: Rotating Speed(Decimal)1. When the projector is NC3200S, refer 2 to 4 item firstly2. (NC3200S) Check the system log.3. (NC3200S) When the GPSU(24V) fail was occurred, update the firmware to releasepackage 2.31.4. (NC3200S) or temporary countermeasure is to re-start ( cold start ) the projector.5. Check the failed fan and replace failed fan.6. Check connector POCN5 on PJDIV PWB.For fan layout, see the appendix157Fan7 Stop(Param1)Fan7 has stopped. (Only for NC3200S)Param1: Rotating Speed(Decimal)1. Check the failed fan and replace failed fan.2. Check connector POCN5 on PJDIV PWB.For fan layout, see the appendix.158Fan8 Stop(Param1)Fan8 has stopped. (Only for NC3200S)Param1: Rotating Speed(Decimal)1. Check the failed fan and replace failed fan.2. Check connector POCN5 on PJDIV PWB.For fan layout, see the appendix.159Fan9 Stop(Param1)Fan9 has stopped. (Only for NC3200S)Param1: Rotating Speed(Decimal)1. Check the failed fan and replace failed fan.2. Check connector POCN5 on PJDIV PWB.For fan layout, see the appendix.160GPSU Fan Stop GPSU Fan has stopped.1. Check the connection between POPSM on PJDIV PWB and GPSU. Check the connection between AC PWB and GPSU.2. Replace GPSU Fan.3. Check GPSU.162Lamp Fan0 Stop(Param1)Lamp cooling fan0 has stopped.Param1: Rotating Speed (Decimal) or HW Prt (Hartware protection)132MMS Fail Built-in MMS internal error.1. Check the connection between T-SENSE PWB and POCN1 on PJDIV PWB.2. Check the TSENS PWB.1. Check the connection between Fan unit and POCN5 on PJDIV PWB.For fan layout, see the appendix.163Lamp Fan1 Stop(Param1)Lamp cooling fan1 has stopped.Param1: Rotating Speed (Decimal) or HW Prt (Hartware protection)164ICP Fan Stop(Param1)ICP fan has stopped.Param1: Rotating Speed(Decimal)1. Check the fan attached on CPU PWB.2. Replace fan.3. Replace CPU PWB.165GPI MACRO(n) Selection InvalidSelection of preset button (n) through GPI is invalid because metadata is enabled.n: Preset Button Number(1-8)1. When the GPI title selection is requested during the operations are not allowed, this message will be shown.166GPI Control(Param1) InvalidProjector control through GPI is invalid because projector is busy.Param1: Canceled GPI control:Lamp Off/ On , Mute Off/ On/Power On/OffSelection of preset button n (n=1..8)1. When the GPI control is requested during the projector is busy, this message will be shown.170OverTemp.Outside Air(Param1)Set inside temperature (Outside Air) is abnormal Param1: Temperature(in deg)171OverTemp.Precaution(Param1)Set inside temperature(LPSU Intake) is close to overtemperature.Param1: Precaution temperature(in deg)172OverTemp.Exhaust(Param1)Set inside temperature (Exhaust) is abnormalParam1: Temperature(in deg)173OverTemp.DMD-B(Param1)Set inside temperature (DMD-B) is abnormal Param1: Temperature(in deg)174Bulb EntryNo selection of current bulb.1. Setup the new bulb entry while the projector is in standby.177Tamper Fail(Param1)Service door tamper switch of projector is open.Param1 : Location of tampering switch.(Param1 is encrypted)LCD: Decrypted while projector is service mode or higher.Log: Decrypted to view while DCC is service mode or higher.1. Check the (Param1) which tells which switch is activated.2. Check if the side covers and lens cover are closed propely.3. Check if the tamper switch lever is broken.4. Check the connection between TAMPER PWB and POCN2/POCN7 on PJDIV PWB.5. Check TAMPER PWB.178Marriage Tamper Fail(Param1)Marriage tamper switch of projector is open.Param1 : Location of tampering switch.(Param1 is encrypted)LCD: Decrypted while projector is service mode or higher.Log: Decrypted to view while DCC is service mode or higher.If Param1=0, reseat Circuit Box.If Param1=1,1. Check if cover plate or option PWB is seated at option slot A.2. Check the connection between TAMPER PWB and PO6012 on PJDIV PWB.3. Check TAMPER PWB.4. Check if ICP PWB/SIB is seated on MOTHER PWB properly.180CPU Fail(Mem) Param1: Param2<->Param3System Test Failed.(Memory)Param1-3: Detailed Test results.1.Check the CPU PWB187GPSU(24V) Fail Power supply is abnormal.(24V)1. When the projector is NC3200S, refer 2 to 4 item firstly.2. (NC3200S) Check the system log.3. (NC3200S) When the GPSU(24V) fail was occurred, update the firmware to release package 2.31.4. (NC3200S) or temporary countermeasure is to re-start ( cold start ) the projector.5. Check the DC power supply voltage.6. Check the connection between GPSU and POPSM on PJDIV PWB.201Error Log Write Fail Failed to store logs into projector system. 1. Replace CPU PWB.210Unknown LPSU Model(Param1)Unexpected LPSU is attached.Param1: Unexpected LPSU Product Model 1. Check if the proper LPSU is used.2. Replace LPSU.211LPSU Fan Stop LPSU fan has stopped.1. Check if the LPSU is powered on.2. Replace LPSU.21312V Outside range(Param1)12V supply is out of range.Param1: Captured voltage value.LCD: invalid Log : valid1. Check the 12v line.2. Check the connection between GPSU and PO6010 on MOTHER PWB.21424V Outside range(Param1)24V supply is out of range.Param1: Captured voltage value.LCD: invalid Log : valid1. When the projector is NC3200S, refer 2 to 4 item firstly.2. (NC3200S) Check the system log.3. (NC3200S) When the GPSU(24V) fail was occurred, update the firmware to release package 2.31.4. (NC3200S) or temporary countermeasure is to re-start ( cold start ) the projector.5. Check the 24v line.6. Check the connection between GPSU and POP24 on PJDIV PWB.215Lamp Filter Time Over(Param1)The time to exchange lamp filter. (Future use)Param1: usage hours1. Change filters216Body Filter Time Over(Param1)The time to exchange body filter. (Future use)Param1: usage hours1. Change filters220AC On Fan Exchange Time The time to exchange Fan(AC On)1. Replace AC On Fan(Fan6) and clear AC On Fan usage time.221Power On Fan Exchange Time The time to exchange Fan(Power On)NC2000C/NC1200C1. Replace Power On Fan(Fan0..5 and 7) and clear Power On Fan usage time.NC3200S1. Replace Power On Fan(Fan0..5 and 7..9) and clear Power On Fan usage time.222Lamp Fan Exchange Time The time to exchange Lamp Fan1. Replace Lamp Cooling Fan 0 and 1 and clear Lamp Cooling Fan usage time.230Router Fail(Param1)Failed to control router.Param1:“Connect” : Failed to connect to router “Tx” : Transmit error “Rx” : Receive error“Tout” : Communication timeout“Msg Format” : Unexpected data received “Data”: No data to setup router “Verify”: Setting verify error 1. If the router unit is replaced to the new, execute "NewRouterSetup" for projector use.2. Power-cycle the projector.3. Check the LAN cable connection between Router unit and MOTHER PWB.4. Execute Factory Default - LAN.5. If the router firmware is Version1.3 Release01, update to Version1.4 Release01.231SensorFail OptFailed to control light sensor.1. Check the connection between POCN3 on PJDIV PWB and LSENS PWB.2. Check the LSENS PWB.232MAC Write Fail Failed to setup MAC address of CPU board.1. Replace CPU PWB.2. Chekc LED on driver PWB.3. Check the failed fan and replace the fan.1. Check the ambient temperature. It should be 35 degC or lower.2. Check if there is any problem on suction air and exhasut air.3. Check the air filter clogging.4. Check if the ventilation system is operated with required specification.5. Check the TSENS PWB233Illegal MAC Address Router WAN MAC address is illegal.1. Power-cycle the projector.2. Replace the Router unit and execute "NewRouterSetup."235Router Self Check Fail(Param1, Param2, Param3)Router health-check error.Param1 : Health check error timing“INIT”: After AC-ON“STBY”: During standby“ RUN”: During power-onParam2: Health check result“2”: Factory default“3”: No responses(Dead lock or something)“4”: Unstable status“5”: Factory default and unstable status“6”: Defective(possibly “2” to “5”)Param3: router response result(Valid when Param2 is “4” and “5”)N of4ping responses1. Check the connection of lan cable.2. Check router.240SIB Comm Fail(Param1Pram2Param3Param4)Failed to communicate with SIB.Param1:“Connect”, “Tx”, “Rx”, “Nack”, “Tout”Param2: First portion of SIBcommand.Param3: Second portion of SIB command.Param4: Third portion of SIB command.When Param1 is “Nack”, nack data is added afterParam4.e.g.) SIB Comm Fail(Nack)010203:0001H1. Check LAN cable between Router and Mother（PO6201）2. Check connection of between SIB PWB (IC1600,IC1604) and Mother PWB241SIB Error(Param1)SIB internal error.Param1: SIB internal error status“FPGA Open”: Failed to open serial I/F“FPGA Tx:nnn”: FPGA send error(nnn: failed send command)“FPGA Rx:nnn”: FPGA receive error(nnn: failed receive command)“MEM Open”: Device driver open error“MEM Read”:Device driver read error1. Check SIB PWB242SIB FPGA Reboot Executed to re-boot SIB FPGA for recovery. 1. Check SIB PWB250Fan0 Stop Precaution(Param1)Fan0 Stop PrecautionParam1: Rotating Speed(Decimal)251Fan1 Stop Precaution(Param1)Fan1 Stop PrecautionParam1: Rotating Speed(Decimal)252Fan2 Stop Precaution(Param1)Fan2 Stop PrecautionParam1: Rotating Speed(Decimal)253Fan3 Stop Precaution(Param1)Fan3 Stop PrecautionParam1: Rotating Speed(Decimal)254Fan4 Stop Precaution(Param1)Fan4 Stop PrecautionParam1: Rotating Speed(Decimal)255Fan5 Stop Precaution(Param1)Fan5 Stop PrecautionParam1: Rotating Speed(Decimal)256Fan6 Stop Precaution(Param1)Fan6 Stop PrecautionParam1: Rotating Speed(Decimal)257Fan7 Stop Precaution(Param1)Fan7 Stop PrecautionParam1: Rotating Speed(Decimal)258Fan8 Stop Precaution(Param1)Fan8 Stop PrecautionParam1: Rotating Speed(Decimal)259Fan9 Stop Precaution(Param1)Fan9 Stop PrecautionParam1: Rotating Speed(Decimal)260Lamp Fan0 Stop Precaution(Param1)Lamp Fan0 Stop Precaution Param1: Rotating Speed(Decimal)261Lamp Fan1 Stop Precaution(Param1)Lamp Fan1 Stop Precaution Param1: Rotating Speed(Decimal)262Pump Stop Precaution(Param1)Pump Stop PrecautionParam1: Rotating Speed(Decimal)263ICP Fan Stop Precaution(Param1)ICP Fan Stop Precaution270SD Tamper Terminate(Param1)Terminated service door tamper event latched by Enigmaboard.LCD: Not supportedLog: Supported1. Check tamper SW280Bulb Warranty Over Bulb warranty time over 1. Change the lamp bulb to new one.301System Error ICP board error 1. Check connection between ICP PWB and Mother PWB.2. Check connection between SIB PWB and ENIGMA PWB.3. Check Frimwarea version of both SIB PWB and ENIGMA PWB.4. Check ICP board.302Self Test Error ICP board error303Install Release Package Error ICP board error304Load Release Package Error ICP board error305Key Error ICP board error 1.Check ICP board.306Certificate Error ICP board error 1. Check connection between ICP PWB and Mother PWB.2. Check connection between SIB PWB and ENIGMA PWB.3. Check Frimwarea version of both SIB PWB and ENIGMA PWB.4. Check ICP board.317ICP Normal Configuration Error ICP board error318ICP Boot Configuration Error ICP board error 319FMT Normal Configuration Error ICP board error 320FMT Boot Configuration Error ICP board error 321FMT Satellite Configuration Error ICP board error 322 1.20V Supply out of range ICP board error 323 1.80V Supply out of range ICP board error 324 2.50V Supply out of range ICP board error Preper DC fan of error and replace to new DC fan.1. Check connection between ICP PWB and Mother PWB.2Check Frimwarea version of both SIB PWB and ENIGMA PWB1. Check connection between ICP PWB and Mother PWB.2. Check connection between SIB PWB and ENIGMA PWB.3. Check Frimwarea version of both SIB PWB and ENIGMA PWB.4. Check ICP board.325 3.30V Regulator out of range ICP board error326ICP FPGA Temperature out of range ICP board error327FMT FPGA Temperature out of range ICP board error328ICP Flash Update Error ICP board error329FMT Sequence Data File Mismatch ICP board error330FMT DMD Data File Mismatch ICP board error331FMT Flash Checksum Error - Sequence Data ICP board error332FMT Flash Checksum Error - DMD Data ICP board error333Satellite Hardware Mismatch ICP board error334FMT Flash Update Error ICP board error335Red Satellite Reports Reset Cinema board error336Red Satellite Serial Link Error Cinema board error337Red Satellite Firmware Configuration Error Cinema board error338Red DAD1000 Bias Under Voltage Error Cinema board error339Red DAD1000 Reset Under Voltage Error Cinema board error340Red DAD1000 Offset Under Voltage Error Cinema board error341Red DAD1000 Thermal Shutdown Error Cinema board error342Green Satellite Reports Reset Cinema board error343Green Satellite Serial Link Error Cinema board error344Green Satellite Firmware Configuration Error Cinema board error345Green DAD1000 Bias Under Voltage Error Cinema board error346Green DAD1000 Reset Under Voltage Error Cinema board error347Green DAD1000 Offset Under Voltage Error Cinema board error348Green DAD1000 Thermal Shutdown Error Cinema board error349Blue Satellite Reports Reset Cinema board error350Blue Satellite Serial Link Error Cinema board error351Blue Satellite Firmware Configuration Error Cinema board error352Blue DAD1000 Bias Under Voltage Error Cinema board error353Blue DAD1000 Reset Under Voltage Error Cinema board error354Blue DAD1000 Offset Under Voltage Error Cinema board error355Blue DAD1000 Thermal Shutdown Error Cinema board error356RTC Error Cinema board error 1. Check ICP PWB400Enigma Comm Fail(Param1Param2Param3:Param4)No communication with the Enigma board.Param1: First portion of Enigma command.Param2: Second portion of Enigma command.Param3: Third portion of Enigma command.Param4: Error Type“Conn=x”, “Tx”, “Rxn”, “Nack=xxxxH”,“Tout=xxxx”1. Check connection between ICP PWB and Mother PWB.2. Check connection between SIB PWB and ENIGMA PWB.3. Check LAN Connector of Moter PWB.4. Check LAN IP address of SIB PWB.5. Check Frimwarea version of both SIB PWB and ENIGMA PWB.410System Error Enigma Status error 1. Check connection between ICP PWB and Mother PWB.2. Check connection between SIB PWB and ENIGMA PWB.3. Check LAN Connector of Moter PWB.4. Check LAN IP address of SIB PWB.5. Check Frimwarea version of both SIB PWB and ENIGMA PWB.411Self Test Error Enigma Status error412Install Release Package Error Enigma Status error413Load Release Package Error Enigma Status error414TI Login List Package Error Enigma Status error415Security Officer Login List Package Error Enigma Status error419Certificate or Key Error Enigma Status error420ICP Communications Status Enigma Status error426User Loader Integrity Error Enigma is in FIPS error state.(Integrity check error) 427Main Application Integrity Error Enigma is in FIPS error state.(Integrity check error) 428RNG Hardware Integrity Error Enigma is in FIPS error state.(Integrity check error) 429DRNG Algorithm Integrity Error Enigma is in FIPS error state.(Integrity check error) 430RSA Algorithm Integrity Error Enigma is in FIPS error state.(Integrity check error) 431AES Algorithm Integrity Error Enigma is in FIPS error state.(Integrity check error) 432HMAC Algorithm Integrity Error Enigma is in FIPS error state.(Integrity check error)1. Check cable betwwn FSB and Moter PWB2. Check ICP PWB connection between ICP and Mother.3. Check ICP PWB.2. Check Frimwarea version of both SIB PWB and ENIGMA PWB.3. Check ICP board.433SHA Algorithm Integrity Error Enigma is in FIPS error state.(Integrity check error)434TLS Integrity Error Enigma is in FIPS error state.(Integrity check error)435FPGA Configuration Integrity Error Enigma is in FIPS error state.(Integrity check error)436FPGA CineLink 2 Decryption Integrity Error Enigma is in FIPS error state.(Integrity check error)437RTC Error Enigma is in FIPS error state.(Integrity check error)442FPGA Configuration Error Enigma Status error443FPGA Temperature out of range Enigma Status error446RNG Hardware Duplicate Output Error Enigma is in FIPS error state.(Integrity check error)447DRNG Algorithm Duplicate Output Error Enigma is in FIPS error state.(Integrity check error)450 1.20V Supply out of range Enigma Status error451 1.80V Supply out of range Enigma Status error452 2.50V Supply out of range Enigma Status error453 3.30V Regulator out of range Enigma Status error458SelfTest User Loader Integrity Error Enigma is in FIPS error state.(Self test result)459SelfTest Main Application Integrity Error Enigma is in FIPS error state.(Self test result)460SelfTest RNG Hardware Integrity Error Enigma is in FIPS error state.(Self test result)461SelfTest DRNG Algorithm Integrity Error Enigma is in FIPS error state.(Self test result)462SelfTest RSA Algorithm Integrity Error Enigma is in FIPS error state.(Self test result)463SelfTest AES Algorithm Integrity Error Enigma is in FIPS error state.(Self test result)464SelfTest HMAC Algorithm Integrity Error Enigma is in FIPS error state.(Self test result)465SelfTest SHA Algorithm Integrity Error Enigma is in FIPS error state.(Self test result)466SelfTest TLS Integrity Error Enigma is in FIPS error state.(Self test result)467SelfTest FPGA Configuration Integrity Error Enigma is in FIPS error state.(Self test result)468SelfTest FPGA CineLink. 2 Decryption Integrity Error Enigma is in FIPS error state.(Self test result)474Security Tamper Security tamper condition exists. 1. Replace Enigma board. 475Top Side Security Enclosure Open Security tamper condition exists. 1. Replace Enigma board. 476Bottom Side Security Enclosure Open Security tamper condition exists. 1. Replace Enigma board. 477Security Battery Event Battery tamper condition exists. 1. Replace Enigma board. 478Software Commanded Zeroization Destroyed Enigma key by software command. 1. Replace Enigma board. 481Security Enclosure Not Armed Enigma security not armed. 1. Do the Arm-Tamper.482Physical Marriage Tamper Latched physical marriage tamper condition on Enigmaboard.1. Check physical Marriage tamper.483Logical Marriage Tamper Logical marriage tamper condition exists. 1. Do re-marrage function. 484Marriage NOT Active Marriage has NOT been established (active). 1. Do re-marrage function. 486Service Door Tamper Latched service door tamper condition on Enigma board1. Check tamper SW487Security Log Error Security log is full.Security log is full.Cinema server delete the security log of projector. Confirm this issue to vender of cinema server.488Security Battery Low Warning Close to “Security Battery Low”. 1. Charge serucity battery.489Security Log Warning Close to “Security Log Error”.Security log is full.Cinema server delete the security log of projector.Confirm this issue to vender of cinema server.1. Check connection between ICP PWB and Mother PWB.2. Check connection between SIB PWB and ENIGMA PWB.3. Check LAN Connector of Moter PWB.4. Check LAN IP address of SIB PWB.5. Check Frimwarea version of both SIB PWB and ENIGMA PWB.。