横河CS3000操作培训2

合集下载
  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

and is in engineering unit)
10
报警状态 (Alarm Status)
Symbol
Name
NR OOP
Normal Output Open Alarm
IOP
High Input Open Alarm
IOP-
Low Input Open Alarm
HH
High High Alarm
过程值上刻度 过程值低刻度
过程值 设定值 输出值 变差:过程值-设定值 累积值 输出上限制指标 输出低限制指标 输出值上刻度限制 输出值低刻度限制
7
休息时间
8
调整窗口 (Tuning Window)
正常
高高报警 高报警 低报警 低低报 速度限制 变差限制
固定高限制 固定低限制
9
报警设置 (Alarm Settings)
自动 串级
3
功能块- 安全级别 (Security - Function Block)
水平
监视
操作
允许
4
位号标志 (Tag Mark)
指出功能块的位号优先权水平 用户可以指定是否确认特征记号 特征记号的颜色显示功能块报警状态
特征记号和位号优先权水平
重要位号 普通位号 辅助位号
5
调整窗口 (Tuning Window)
VEL + : rate of change of pv (dpv/dt) is increasing faster than 10/sec.(example and is in engineering unit)
VEL - : rate of change of pv (dpv/dt) is
decreasing faster than 10/sec. (example
The process variable has risen above a high-high limit alarm setpoint.
The process variable has fallen below a low-low limit alarm setpoint.
The process variable has risen above a high limit alarm setpoint.
第一天
第二天 第三天
1
Hale Waihona Puke 仪表面板 (Instrument Faceplate)
工位号
位号注释
工位标记
操作模式 报警状态 过程值 设定值 输出值
工程单位
量程上刻度
输出指针
报警设置 设定值指针
过程值棒状图
低刻度
2
操作仪表面板 (Operating Instrument Faceplate)
改变模式
手动
The input enters the data status BAD because of failures or disconnections in the final control element or process I/O equipment or invalide data at the input destination. Normally, input signal processing is halted.
Process variable 过程值
HH
滞后 Hysteresis 2% of span
Process variable 过程值 PH
滞后 Hysteresis 2% of span
跨度
LL
NR
HH
HH : PV > HH
LL : PV < LL
+ 变差 Deviation (DV) 0
-
DL DL
If input overshoots due to a disconnection, for example, it overshoots in the high-limit direction.
Input overshoots in the low-limit direction because of a disconnection in the input signal. The input enters the data status BAD, and normallu, input signal processing is halted.
NR
+DV
DV+ : DV > DL
DV- : DV < DL
Time NR
滞后 Hysteresis 1% of span Time
NR
PL
Time
NR
HI
NR
HI : PV > PH
LO : PV < PL
VL : velocity limit i.e. change in process variable during a specified detection time interval. (dpv/dt)
LL
Low Low Alarm
HI
High Alarm
LO
Low Alarm
Definition
Alarm conditions do not exist at all.
The output enters the data status PTPF (output failure) because of failures or disconnections in the final control element or process I/O equipment or invalid data at the output destination. Normally, output action is halted.
系统Centum CS 3000操作– R3
一 Centum CS 3000 总系统 /硬件 标准 操作面板 (Standard Operation Panels)
二调节控制和顺序控制功能
三 过程报表 (Process Report) 系统状态显示(System Status Display) HIS 设置(HIS Setup)
显示独立功能块的详细控制状态
打印调整窗口
确认信息
保存趋势资料 停止/继续显示资 料. 缩小/扩大 X 轴
缩小/扩大 Y 轴
显示顺序图表窗 口
显示原资料对话
显示控制图状态窗 口.
显示操作分配记号
显示逻辑图表窗 口
转变成校准模式.
转变成中断报警模 式
转变成主要指引模 式
6
调整窗口 (Tuning Window)
相关文档
最新文档