机械图纸中常用词汇英语缩写

机械图纸英语翻译
以下是我在工作中常用的
ALL WELDS CONTINUOUS UNLESS OTHERWISE STATED. 未注焊缝均为连续焊
ALL WELDS 3mm FILLET UNLESS OTHERWISE STATED 未注焊角高3mm. ALL UNSPECIFIED RADI - R3 未注圆角R3
REMOVE ALL BURRS AND SHARP EDGES 棱角倒钝
CHANNEL 槽钢RSA 708 角钢70X70X8
M30X1.5
pitch M30X1.5的锥螺纹
Tackweld 点焊
OD 1/4" outside dimension 1/4"的缩写外径直1/4"
75 CRS 尺寸为75 材质为冷轧钢板
410 OPENING REF 410 张口参照尺寸
40 REF 尺寸为40,参照值
2.5" BSP 2.5” 圆锥管螺纹
2.5" BSPT HEXAGON 2.5” 六角圆锥管螺纹(即对丝)
30x2.5 FLAT BAR 30X2.5 扁钢
TYP 2 POSNS 2处
11 TOTAL COILS APROX.9 WORKING COILS APROX.RIGHT HAND WOUND ONLY,END COILS SQUARE TO TOUCH.
总圈数约11圈；工作圈数约9圈；右旋；弹簧的端部磨平以便于接触.(此为弹簧技术说明) FEMALE: 内扣(母扣)
MALE: 外扣(公扣)
独爱轴eccentric shaft
销轴PIN 张口销COTTER PIN
螺杆screw
紧定螺钉SET SCREW
圆螺母ROUND NUT
内六角螺钉SOCKET HEAD CAP SCREW
六角螺钉HEX HD SETSCREW
六角螺栓HEX HD BOLT
挡圈closing ring
弹性挡圈circlip
轴承隔套distance sleeve of axletree
轴承axletree
深沟球轴承DEEP GROOVE BALL BEARING
无扣长non-buckle longth
弹簧SPRING
吊环螺钉LIFTING EYE BOLT
开槽盘头螺钉SLOTTED PAN HEAD SCREW
圆锥滚子轴承TAPERED ROLLER BEARING
推力球轴承THRUST BALL BEARING
平键FLA T KEY
弹簧垫圈SINGLE COIL SPRING WASHER 平垫圈FLAT WASHER
螺母FULL NYLOCK NUT
圆螺母ROUND NUT
REMOVE ALL BURRS AND SHARP EDGES 所有尖角/棱角倒角并去毛刺
40 REF 为测量的参照尺寸
OD 1/4’ outside dimension 1/4"的缩写外径直1/4’------->应该为：外径值1/4"
75 CRS 尺75 材质为冷轧钢板------->应该为：尺寸75 材质为冷轧钢板
我见过18GA(.048")CRS、16GA(.060)CRS、14GA(.075)CRS，其中GA是表示厚度的，但与英寸的关系还没研究理解；照此计算75是相当薄的
缩写全称翻译
ACCESS Accessory 附件
ADJ Adjustable,Adjust 调整
ADPT Adapter 使适应
ADV Advance 提前
AL Aluminum 铝
ALLOW Allowance 赞同
ALT Alternate 改变
ALY Alloy 合金
AMT Amout 数量
ANL Anneal 锻炼
ANSL Amer Natl Stds Institute
APPROX Approximate 大体
ASME Amer Society of Mech Engrs ASSEM Assemble 装置
ASSY Assembly 装置
AUTH Authorized 授权的
AUTO Automatic 自动的
AUX Auxiliary 辅助的
A VG Average 平均
AWG American Wire Gauge
BC Bolt Circle 螺栓圆周
BET Between 之间
BEV Bevel 斜角
BHN Brinell Hardness Number 布氏硬度值
BLK Blank ,Block 空白
B/NM Bill of Material 资料费
BOT Bottom 底部
BP or B/P Blueprint 宏图
BRG Bearing 轴承
BRK Break 破裂
BRKT Bracket 支架
BRO Broach 钻孔
BRS Brass 黄铜
BRZ Bronze 青铜
B＆S Brown＆Shape 棕色＆形状
BSC Basic 基本的
BUSH Bushing 套管
BWG Birmingham Wire Gauge
C TO C Center-to-Center 中心到中心CA
D Computer-Aided Drafting 电脑辅助设计
CAM Computer-Aided Mfg
CAP Capacity 容量
CAP SCR Cap Screw 螺帽
CARB Carburize 使渗碳
CBORE Counterbore 扩孔CCW Counter Clockwise 逆时针CDRILL Counerdrill
CDS Cold-Drawn Steel
缩写全称翻译
EFF Effective 有效的
ENCL Enclose,Enclosure 附上
ENG Engine 引擎
ENGR Engineer 工程师
ENGRG Engineering 工程学EQLSP Equally Spaced 等距
EQUIV Equivalent 相等
EST Estimate 估计
EX Extra 额外
EXH Exhaust 耗资
EXP Experimental 实验性的
EXT Exension,External 范围,外面FAB Fabricate 捏造
FAO Finish All Over
FDRY Foundry 铸造
FIG Figure 数据
FIL Fillet,fillister 带子
FIM Full Indicator Movement
FIN Finish
FLX Fixture 结构
FLX Floor.Fluid,Flush 基地,液体,冲洗FLEX Flexible 易波折的
FLG Flange 边缘
FORG Forging 锻炼
FR Frame,Front 边框
FIG Fitting 装置
FURN Furnish 供应
FWD Forward 向前
GA Gage,Gauge 测量
GALV Galvanized 电镀
GR Grade 等级
GRD Grind 磨碎
GRV Groove 凹槽
GSKT Gasket 垫圈
H＆G Harden and Grind 加硬和磨碎HD Head 主要的
HDL Handle 办理
HDLS Headless 无领导的
HDN Harden 使硬化
HDW Hardware 硬件
HEX Hexagon 六边形
HGR Hanger 衣架
HGT Height 高度
HOR Horizontal 水平的
HRS Hot-Rolled Steel
HSG Housing 外罩
HT TR Heat Treal
我见过18GA(.048")CRS、16GA(.060)CRS、14GA(.075)CRS，其中GA是表示厚度的，但与英寸的关系还没研究理解；照此计算75是相当薄的
缩写全称翻译
ACCESS Accessory 附件
ADJ Adjustable,Adjust 调整
ADPT Adapter 使适应
ADV Advance 提前
AL Aluminum 铝
ALLOW Allowance 赞同
ALT Alternate 改变
ALY Alloy 合金
AMT Amout 数量
ANL Anneal 锻炼
ANSL Amer Natl Stds Institute
APPROX Approximate 大体
ASME Amer Society of Mech Engrs ASSEM Assemble 装置
ASSY Assembly 装置
AUTH Authorized 授权的
AUTO Automatic 自动的
AUX Auxiliary 辅助的
A VG Average 平均
AWG American Wire Gauge
BC Bolt Circle 螺栓圆周
BET Between 之间
BEV Bevel 斜角
BHN Brinell Hardness Number 布氏硬度值
BLK Blank ,Block 空白
B/NM Bill of Material 资料费
BOT Bottom 底部
BP or B/P Blueprint 宏图
BRG Bearing 轴承BRK Break 破裂
BRKT Bracket 支架
BRO Broach 钻孔
BRS Brass 黄铜
BRZ Bronze 青铜
B＆S Brown＆Shape 棕色＆形状
BSC Basic 基本的
BUSH Bushing 套管
BWG Birmingham Wire Gauge
C TO C Center-to-Center 中心到中心CA
D Computer-Aided Drafting 电脑辅助设计
CAM Computer-Aided Mfg
CAP Capacity 容量
CAP SCR Cap Screw 螺帽
CARB Carburize 使渗碳
CBORE Counterbore 扩孔
CCW Counter Clockwise 逆时针CDRILL Counerdrill
CDS Cold-Drawn Steel
缩写全称翻译
EFF Effective 有效的
ENCL Enclose,Enclosure 附上
ENG Engine 引擎
ENGR Engineer 工程师
ENGRG Engineering 工程学
EQLSP Equally Spaced 等距
EQUIV Equivalent 相等
EST Estimate 估计
EX Extra 额外
EXH Exhaust 耗资
EXP Experimental 实验性的
EXT Exension,External 范围,外面
FAB Fabricate 捏造
FAO Finish All Over
FDRY Foundry 铸造
FIG Figure 数据
FIL Fillet,fillister 带子
FIM Full Indicator Movement
FIN Finish
FLX Fixture 结构
FLX Floor.Fluid,Flush 基地,液体,冲洗FLEX Flexible 易波折的
FLG Flange 边缘
FORG Forging 锻炼
FR Frame,Front 边框
FIG Fitting 装置
FURN Furnish 供应
FWD Forward 向前
GA Gage,Gauge 测量
GALV Galvanized 电镀
GR Grade 等级
GRD Grind 磨碎
GRV Groove 凹槽
GSKT Gasket 垫圈
H＆G Harden and Grind 加硬和磨碎HD Head 主要的
HDL Handle 办理
HDLS Headless 无领导的
HDN Harden 使硬化
HDW Hardware 硬件
HEX Hexagon 六边形
HGR Hanger 衣架
HGT Height 高度
HOR Horizontal 水平的
HRS Hot-Rolled Steel
HSG Housing 外罩
HT TR Heat Treal
缩写全称翻译
NTS Not to Scale
OA Over All 所有
OBS Obsotetc
OC On Center
OD Outside Diameter 外直径
OPP Opposite 对峙
OPTL Optional 可选择的
OR Outside Radius 外半径
ORIG Original 初始的PAT. Patent 专利
PATT Pattern 形式
PC Piece,Pitch Circle 件，节距圆PCH Punch 打孔
PD Pitch Diameter
PERF Perforate 打孔
PERM Permanent 永久的
PERP Perpendicular 垂直的
PFD Preferred 首选的
PKG Package,Packing 包装
PL Parting Line,Places,Plate
PNEU Pncumatic
PNL Panel 面板
POL Polish 磨光
POS Position,Postive 地址
PR Pair 对峙
PRI Primary 基本的
PROC Process 程序
PROD Product,Production 产品，产量PSI Pounds per Square Inch
PT Part,Point 零件，点
QTR Quarter 四份之一
QTY Quantity 数量
QUAL Quality 质量
R Radius 半径
RA Rockwell Harden,A-Scale
RB Rockwell Harden,B-Scale
RC Rockwell Harden,C-Scale
RECD Received 巳收到的
RECT Rectangle 长方形
REF Reference 相关的
REINF Reinforce 加强
REL Release,Relief 释放，缓解
REM Remove 移除
REQD Requird 有需要
REE Retainer,Return
REV Reverse,Revision,Revolution
RFS Regardless of Feature Size
RGH Rough 粗糙的
RH Right Hand 右手
RIV Rivet 起皱
RM Ream 扩展
RND Round 周围
RPM Revolutions per Minute
RPW Resistance Projection Weld
SAE Society of Automotive Engrs
SCH Schedule 进度表
CFS Cold-Finished Steel
CH Case Harden
CHAM Chamfer 斜面
CHAN Channel 渠道
CHG Change 改变
CHK Check 核查
CI Cast Iron 铸铁
CIR Circle, Circular 圆周
CIRC Circumference 圆周
CL Centerline 中心线
CLP Clamp 夹子
CNC Computer Numerical Control 电脑数值控制
COMB Combination 联合
COML Commercial 商业的
CONC Concentric 同中心的
CONN Connect,Connector 连接器
COV Cover 盖子
CPLG Coupling 联系
CQ Commercial Quality 商业等级钢CRS Cold Stds Association
CRT Cathode Ray Tube 阴级射线管
CS Cast Steel 铸铁
CSA Canadian Stds Association
CSK Countersink 专心孔
CSTG Casting 铸件
CTR Center 中心
CU Cubic 立方米
CW Clockwise 顺时针
CYL Cylinder,Cylindrical 柱面
DBL Double 双倍
DEC Decimal 小数
DEG Degree 摄氏度
DET Detail 详情
DEV Develop 发展
DFT Draft 稿本
DIA Diameter 直径
DIM Dimension 尺寸
DIST Distance 距离
DN Down 向下
DP Deep,Diametral Pitch 深度,径节DR Drill,Drill Rod 钻孔
DSGN Design 设计
DVTL Dovetail 切合
DWG Drawing 图纸
DWL Dowel 木钉
DWN Drawn 拔出
EA Each 每个
ECC Eccentric 独特
缩写全称翻译
HVY Heavy 重量
HYD Hydraulic 水压
ID Inside Diameter 内部直径
IDENT Identification 判断
ILLUS Illustration 说明
IN Inch 英寸
INCL Include,Including 包括
INCR Increase 增加
INFO Information 信息
INSP Inspect 检查
INSTL Install 安装
INST Instruct,Instrument 指示,工具
INT Interior,Internal,Intersect 内部的,内在的,交叉
IR Inside Radius 内部半径
ISO Internal Stds Organization 国际标准化组织
JCT Junction 连接
JNT Journal 杂志
JT Joint 连接
K Key 要点
KNRL Knurl 硬节
KST Keyseat
KWY Keyway 键沟
LB Pound 英镑
LBL Label 标签
LG Length,Long 长度
LH Left Hand 左手
LMC Least Material Condition
LOC Locate 位于
LT Light 光
LTR Letter 信
LUB Lubricate 润滑
MACH Machine 机器
MAINT Maintenance 保护
MATL Material 资料
MAX Maximum 最大
MECH Mechanical,Mechanism 机械MED Medium 媒介
MFG Manufacturing 制造业
MI Malleable Iron 可铸造的铁
MIN Minimum, Minute 最小，秒MISC Miscellaneous 混杂的
MM Millimeter 毫米
MMC Max Material Condition
MS Machine Steel
MTG Mouting 装备
MULT Multiple 倍数
MWG Music Wire Gagug
NA Not Applicable 不可以应用的NATL National 国内的
NC Numerical Control 数字电脑控制NEG Negative 忽略的
NO. Number 号码
NOM Nominal 名义上的
NPSM Natl Pipe Straight Mech
NPT Natl Pipe Tapered
缩写全称翻译
SCR Screw 螺丝
SEC Second 秒
SECT Section 部分
SEP Separate 独立
SEQ Sequence 序次
SER Serial,Series 系列
SERR Serrate 锯齿状
SF Spotface
SFT Shaft 轴
SGL Single 单个
SH Sheet 纸
SI Intl System of Units
SL Slide 使滑动
SLV Sleeve 袖子
SOC Socket 插座
SP Space,Spaced,Spare 空间
SPL Special 特别
SPEC Specification 规格
SPG Spring 跳SPHER Spherical 球体
SPRKT Sprocket 链轮齿
SQ Square 平方
SST Stainless Steel 纯铁
STD Standard 标准
STK Stock 存货
STL Steel 铁
STR Straight,Strip 直的
SUB Substitute 取代物
SUP Supply,Support 供应
SURF Surface 表面
SYM Symmetrical 对称的
SYS System 系统
T Teeth,Tooth 牙齿
TECH Technical 技术
TEMP Template,Temporary 模板，暂时的
THD Thread 线
THK Thick 厚的
TOL Tolerance 公差
TOT Total 总计
TPF Taper per Foot
TPI Taper per In,Threads per Inch
TPR Taper 锥形
TS Tool Steel
TYP Typical 典型
UNC Unified Natl Coarse
UNEF Unified Natl Extra Fine
UNF Unified Natl Fine
UNIV Universal 宽泛
VAR Variable 变量
VERT Vertical 垂直的
VOL V olume 音量
VS Versus 与．．相对
W Wide,Width 宽度
WASH Washer 洗衣机
WDF Woodruff 车叶草
WI Wrought Iron 熟铁
WT Weight 重量
齿轮及齿轮加工中英文比较-A部分
A.
1. abrasive tooth wear 齿面研磨磨损
2. absolute tangential velocity 绝对切向速度
3. accelerometer 加速表
4. addendum 齿顶高
5. addendum angle 齿顶角
6. addendum circle 齿顶圆
7. addendum surface 上齿面
8. adhesive wear 粘着磨损
9. adjustability 可调性
10. adjustability coefficients 可调系数
11. adjusting wedge 圆盘端铣刀的可调型楔块
12. allowable stress 赞同应力
13. alternate blade cutter 双面刀盘
14. angular backlash 角侧隙
15. angular bevel gears 斜交锥齿轮
16. angular displacement 角移位
17. angular pitch 齿端距
18. angular testing machine 可调角度试验机
19. approach action 啮入
20. arbor 心轴
21. arbor distance 心轴距
22. arc of approach 啮入弧
23. arc of recess 啮出弧
24. attraction 收紧
25. average cutter diameter 平均刀尖直径
26. axial displacement 轴向位移
27. axial factor 轴向系数
28. axial locating surface 轴向定位面
29. axial pitch 轴向齿距
30. axial plane 轴向平面
31. axial rakeangle 轴向前角
32. axial thrust 轴向推力
33. axle testing machine 传动桥试验机
第4楼
Piping work: 铺管工程
Steam trace: 加热蒸汽管道
Cutting: 切割
socket weld 承插焊接
fillet weld 角焊,填角焊
branch connection 分支接续fabrication tolerance .制造容差
local heat treatment 局部热办理threaded pipe 螺纹管
seal welding 密封焊接
flange joint 凸缘接头undercut 底切
feeder 馈电线
conduit outlet 电线引出口
seal fitting 密封接头, 密封配件Screw thread lubricant 螺纹润滑剂Seal 绝缘层
weld reinforcement 焊缝补强
lock washer 锁紧[止动, 防松]垫圈electrical panel 配电板,配电盘
nipple 螺纹接头
zinc plated 镀锌的
ring joint 环接, 围缘接合
bolt 螺栓
control 控制器
National Electrical Code 全国电气规程master schedule 主要图表, 综合图表, 设计任务书, 主要作业表
torque wrench 转矩扳手
job site 施工现场
flange connection 凸缘联接
Hard hat 安全帽
Goggles 护目镜
Stockpile 储藏
packing list 装箱单
crate 柳条箱
purchased material list 原资料进货单back-feed 反响
wire coil 线盘线卷
NPT thread 美国标准锥管螺纹
cable gland 电缆衬垫
terminal block 线弧, 接头排接线盒, 接线板, 线夹
power drill 机械钻
connector 接线器
insulated sleeve 绝缘套管
wire connector 接线器
wire terminal 电线接头
control wiring 控制线路
motor lead 电动机引出线
power wiring 电力布线
tender document 供应证件
orifice plate 挡板
nut 螺母
flange gasket 法兰垫片
dimensional inspection 尺寸检验
burn through 烧蚀
piping system 管道系统
reinforcement of weld 加强焊缝
械专业词汇表
"机械(常用)"
"abrasion, abrasive wear","磨料磨损" "active force, applied force","作用力" "actual size","实质尺寸"
"addendum angle","齿顶角" "addendum","齿顶高"
"addendum modification","径向变位" "addendum modification (for external gears)","径向变位量"
"addendum modification coefficient","径向变位系数"
"additive ","增加剂"
"adhesion wear","黏着磨损"
"adjusted rating life","修正额定寿命" "aerodynamic bearing","气体静压滑动轴承" "air spring","空气弹簧"
"angle drive","角度传动"
"angle of contact","包角"
"angle of transmission","作用角"
"angular bevel gear ","斜交锥齿轮" "angular contact bearing","角接触推力轴承" "angular contact bearing","角接触轴承"
"anti-friction bearing material","减磨轴承资料" "approach, engaging-in","啮入" "archimedes spiral","阿基米德螺线" "attitude angle","偏位角"
"auto-controlled clutch","自控离合器"
"axial load factor","轴向载荷系数"
"axial modification","齿向修形"
"axial module","轴向模数"
"axial pitch","轴向齿距"
"axial plane","轴平面"
"axial plane of wormwheel","蜗轮轴平面" "axial profile","轴向齿廓"
"back cone","背锥面"
"back cone angle","背锥角"
"back cone distance","中点锥距" "back cone tooth profile","背锥齿廓"
"back to back arrangement (rolling bearing)","背对背配置(转动轴承)"
"balancing mass","平衡质量"
"ball oscillating teeth","滚珠活齿"
"ball screw","滚珠丝杠"
"ball screw","滚珠丝杠"
"ball bearing","球轴承"
"band brake","带式制动器"
"base circle","基圆"
"base helix","基圆螺旋线"
"base tangent length","公法线长度"
"basic profile","基本牙型"
"basic rack","基本齿条"
"basic rack tooth profile","基本齿廓"
"basic rating life","基本额定寿命"
"basic size","基本尺寸"
"bath lubrication","油浴润滑"
"bathtub curve","浴盆曲线" "bearing","轴承"
"bearing axial load","轴承轴向载荷" "bearing bore diameter","轴承内径" "bearing bush","轴套"
"Bearing characteristic number","轴承特点系数"
"bearing liner","轴承衬"
"bearing load carrying capacity","轴承承载能力"
"bearing mean specific load","轴承压强" "bearing outside diameter","轴承外径" "bearing radial load","轴承径向载荷" "bearing ring","轴承套圈"
"bearing series (rolling bearing)","轴承系列(转动轴承)"
"bearing width","轴承宽度"
"bearing with solid lubricant","固体润滑滑动轴承"
"belleville spring","碟形弹簧"
"belt drive","带传动"
"belt length","带长"
"bending vibration","波折振动"
"bevel gear","锥齿轮"
"bevel gear with axes at right angles","正交锥齿轮"
"bevel gear with circular arc tooth profile","双重锥度齿锥齿轮"
"bevel gear with circular arc tooth profile","圆弧齿廓锥齿轮"
"bevel gear with standard taoered tooth profile","正常锥度齿锥齿轮"
"bevel gear with straight tooth profile","直线齿廓锥齿轮"
"bevel gear wuth 90° face angle","平顶齿轮" "block brake","块式制动器"
"block chain","块链"
"bobed bearing","多油叶滑动轴承" "bolt","螺栓"
"bottom clearance","顶隙"
"bottom land","齿槽底面"
"boundary dimension (rolling bearing)","外形尺寸(转动轴承)"
"boundary lubrication ","界线摩擦" "brake","制动器"
"brake drum","制动鼓"
"brake lining","制动衬片"
"brake piece","制动块"
"brake shoe","制动蹄"
"brake-band clutch","闸带离合器"
"bush chain","套筒链"
"cage","保持架"
"cam","凸轮"
"cam contour, cam profile","凸轮工作轮廓" "cam follower","凸轮从动件"
"cam pitch curve","凸轮理论轮廓" "Cavitation wear","气蚀磨损"
"center distance","中心距"
"center distance modification coefficient","中心距变动系数"
"center gear","中心轮"
"centric slider-crank mechanism","对心曲柄滑块机构"
"centrifugal clutch","离心离合器" "centrifugal tension","离心拉力" "centrifugal force","离心力"
"centrode mechanism","瞬心线机构" "Ceramic friction material ","金属陶瓷" "chain","链条"
"chain coupling","链条联轴器" "chain transmission","链传动" "chainwheel, sprocket","链轮"
"chordal height","弦齿高"
"circular arc profile","圆弧齿廓"
"circular helix","圆柱螺旋线"
"circular-arc gear","圆弧圆柱齿轮" "Circulating lubrication","循环润滑" "circumferential backlash","圆周侧隙" "classical V-belt","一般V带"
"clearance fit","缝隙配合"
"clevis pin with head","销轴"
"clutch ","离合器"
"coefficient of travel speed variation, advance- to-return time ratio","行程速度变化系数" "combined spring","组合弹簧"
"common apex ","公共锥顶" "compensator (hydrostatic bearing)","补偿器(静压轴承〕"
"compost bearing material","复合轴承资料" "compound planetary gear train","组合行星齿轮系"
"compound hinges, multiple hinges","复合铰链" "concave side","凹面"
"cone pulley","锥轮"
"conical pin , taper pin","圆锥销"
"conical spiral","圆锥螺旋线"
"conical spring","截锥螺旋弹簧" "conjugate flank","共轭齿面"
"conjugate profile","共轭齿廓"
"connecting link","联接链节" "Consistency","稠度"
"constant loading","恒幅载荷"
"constant rate (stiffness) spring","等刚度弹簧" "constant velocity motion curve","等速运动轨迹"
"contact fatigue ","接触疲倦"
"Contact fatigue","接触疲倦"
"contact ratio","重合度"
"Continuous lubrication ","连续润滑" "continuous system","连续系统"
"contrate gear","端面齿轮"
"controlled clutch","控制离合器" "conventional belt","一般平带"
"convex side","凸面"
"conveyor chain","输送链" "corresponding flanks","同侧齿面"
"cosine acceleration motion curve","余弦加速度运动轨迹"
"cotter pin ,split pin","张口销"
"cotton belt","编织平带"
"counterpart rack ","产形齿条" "couple","力偶"
"coupled modes","耦合振型"
"coupler, floating link","连杆"
"coupling ","联轴器"
"coupling with corrugated pipe","涟漪管联轴器"
"coupling with elastic spider","梅花形弹性联轴器"
"coupling with non-metallic elastic element","非金属弹性元件联轴器"
"coupling with rubber plates","橡胶板联轴器" "coupling with rubber type element","轮胎式联轴器"
"crank","曲柄"
"cranked link chain","弯板链"
"crank-rocker mechanism","曲柄摇杆机构" "crest","齿顶"
"crew mechanism","螺旋机构"
"cross recessed countersunk head screw","十字槽沉头螺钉"
"cross recessed pan head screw","十字槽盘头螺钉"
"cross-belt drive","交叉传动"
"crossed helical gear pair","交叉轴斜齿轮副" "crossed roller bearing","交叉滚子轴承" "crossing point of axes","轴线交点"
"crown gear","冠轮"
"crowned teeth","鼓形齿"
"cumulative error in pitch ","螺距累积误差" "cumulative fatigue damage","疲倦累积伤害" "curtate cycloid","短幅摆线"
"curtate epicycloid","短幅外摆线"
"curtate involute","缩短渐开线"
"curvature correction factor (spring)","曲度系数(弹簧)"
"curved tooth bevel gear","曲线齿锥齿轮" "cycl, , ic loading","循环载荷" "cycloid","摆线"
"cycloidal drive with small teeth difference","摆线少齿差传动"
"cycloidal profile","摆线齿廓"
"cycloidal-pin gear speed reducer","摆线针轮减速器"
"cylindrical gear","圆柱齿轮"
"cylindrical helical compression spring","圆柱螺旋压缩弹簧"
"cylindrical helical tension spring","圆柱螺旋拉伸弹簧"
"cylindrical helical torsion spring","圆柱螺旋扭转弹簧"
"cylindrical pin, straight pin","圆柱销" "cylindrical roller bearing","圆柱滚子轴承" "cylindrical worm","单导程圆柱蜗杆" "cylindrical worm","圆柱蜗杆" "damping","阻尼"
"datum circumference","基准圆周长" "datum diameter","基准直径"
"datum line differential","基准线差"
"datum plane","基准平面"
"datum width","基准宽度" "dedendum","齿根高"
"dedendum anle","齿根角"
"deep groove ball bearing","深沟球轴承" "degree of freedom","自由度"
"deviation ","尺寸误差"
"deviation in pitch ","螺距误差"
"diameter series (rolling bearing)","直径系列(转动轴承)"
"diametral pitch","径节"
"diaphragm coupling","膜片联轴器" "differential mechanism","差动机构" "differential screw mechanism","差动螺旋机构" "dimension series (rolling bearing)","尺寸系列(转动轴承)"
"discrete system","失散系统"
"disengaging time (clutch)","分别时间(离合器)"
"distortion","畸变"
"double direction thrust bearing","双向推力轴承"
"double row bearing","双列轴承"
"double V-belt","双面V带"
"double-circular-arc gear","双圆弧齿轮" "driven","从动件"
"driven gear","从动齿轮"
"driven pulley","从动带轮"
"driving gear","主动齿轮"
"driving pulley","主动带轮"
"driving force","驱动力"
"driving link ","主动件"
"dry friction ","干摩擦"
"dual clutch","双作用离合器"
"dual lead cylindrical worm","双导程圆柱蜗杆" "duplex roller chain","双排滚子链" "dynamic load","动载荷"
"dynamic balance of rotor","转子的动平衡" "dynamic load","动载荷"
"dynamics of machinery","机械动力学" "eccentric element","独爱元件"
"eccentric mechanism","独爱轮机构" "effective circumference","有效圆周长" "effective coil number","有效圈数" "effective diameter","有效直径"
"effective line differential","有效线差" "effective stress concentration factor","有效应力集中系数"
"effective tension","有效拉力"
"effective width","有效宽度"
"effective resistance","工作阻力" "efficiency","效率"
"elastic pin coupling ","弹性柱销齿式联轴器" "elasto-hydrodynamic lubrication ","弹性流体动力润滑"
"electromagnetic clutch","电磁离合器" "electromagnetic whirlpool brake","电磁涡流制动器"
"electrostatic bearing","静电轴承"
"elliptic bearing","椭圆滑动轴承" "embeddability","嵌入性"
"end relief","齿端修薄" "engagement","啮合"
"engaging time(clutch)","接合时间(离合器)" "engaging(clutch)","接合过程(离合器)" "epicycloid","外摆线"
"epicycloid gear","摆线齿锥齿轮" "equidistant curve of curtate hypocycloid","短幅外摆线的等距曲线"
"equidistant curve of epicycloid","内摆线的等距曲线"
"equidistant curve of epicycloid","外摆线的等距曲线"
"equidistant curve of prolate epicycloid","长幅外摆线的等距曲线" "equilibrium","力平衡"
"Equivalent coefficient of friction","当量摩擦系数"
"equivalent load","当量载荷"
"equivalent force","等效力"
"equivalent link","等效构件"
"equivalent mass","等效质量"
"equivalent moment","等效力矩" "escapement","擒纵机构"
"external thread","外螺纹"
"external gear","外齿轮"
"external pin wheel","外齿针齿轮" "external tab washer","外舌止动垫圈" "external teeth lock washer ","外齿锁紧垫圈" "Extreme-pressure lubrication","极压润滑" "face to face arrangement (rolling bearing)","当面配置(转动轴承)"
"facewidth","齿宽"
"failure","无效"
"farthest dwell angle","远休止角" "Fastener","紧固件"
"fatigue limit","疲倦极限"
"fatigue strength","疲倦强度" "fault","故障"
"feather key","滑键"
"feather key ,dive key","导向平键" "fillet","齿根过渡曲面"
"fillet radius","齿根圆角半径"
"filling slot balll bearing","装填槽球轴承" "finite life design","有限寿命设计"
"flange coupling","凸缘联轴器"
"flanged bearing","凸缘轴承"
"flat belt drive","平带传动"
"flat key","平键"
"flat spring","片弹簧"
"flat spring coupling","簧片联轴器"。