acer 投影仪 说明书

Product Features Package Overview Panel Control Connection Ports Remote Control Powering On/Off the Projector Powering On the Projector Warning Indicator Adjusting the Projector Height On-Screen Display Menus How to operate Language Image-II (Computer Mode)Image-II (Video Mode)Troubleshooting Specifications Compatibility Modes
Do:
Don’t:
ventilation.
-
-
-
-
TM
Power Cord 1.8m VGA Cable 1.8m Remote Control 2 x Battery
1.8m Carrying Case VGA to Component/HDTV Adapter
S-Video Cable 1.8m User’s Guide Quick Start Card
Main Unit Focus Ring Zoom Ring Elevator Button Zoom Lens Remote Control Receiver Connection Ports Power Connector Panel Control
513864
Temp Indicator LED
Lamp Indicator LED Power/Standby
Four Directional Select Keys 7.Keystone Correction
8.Menu (On/Off)
9.Re-sync
Panel Control Connection Ports
Remote Control Receiver
PC Analog Signal/HDTV/ Component Video Input
Monitor Loop-through Output
Audio Input Connector
TM Lock Port Composite Video Input
S-Video Input Connector USB Connector
2
16
3
7
8
7... English
1 6 9 11 7 8 10 1
2 14 1315Transmit Indicator Light Volume ( + / - )Page Up / Page Down Keystone Correction Four Directional Select Keys
12.Enter 13.VGA Source 14.S-Video Source posite Video Source
1.Power Cord
2.VGA Cable
posite Video Cable
4.Audio Cable Jack/RCA (optional)
5.S-Video Cable
6.VGA to Component/HDTV Adapter
B Cable (optional)
S-Video Output Digital Tuner Output
Power/Standby
1
2 Turn on the
projector first and then
Lens cap
1.
2.
3.
4.
projector. 5.
o, then
Adjusting Projection Image Size
(82.5cm)
185.7"(471.7cm)
(589.6cm)
84.4"(214.3cm)
140.6"(357.1cm)
225.0"(571.4cm)
281.2"(714.3cm)
4.59'9.84'(1.4m)(3.0m)
Panel Control
Remote Control
Using the Panel Control
Power/Standby
Refer to the “Power On/Off the Projector” section on pages 10-11.
Source
Press “Source” to choose RGB, Component-p, Component-i, S-Video, Composite Video and HDTV sources.
Menu
Press “Menu” to launch the on screen display (OSD) menu.
To exit OSD, press “Menu” again.
keys to select the main menu.
Setting
Image-I
Brightness
Adjusting the brightness of the image.
Press the to darken image.
Press the to lighten the image.
Reset
Choose “Yes” to return the display parameters (except for Lamp Hour) on all menus to their factory default settings.
Image-II
(Computer Mode)
Reset
Choose “Yes” to return the display parameters (except for Lamp Hour) on all menus to their factory default settings.
Image-II (Video Mode)
Management
Menu Location
Choose the Menu location on the display screen. Projection
7.
1.
2.
Mirroring “On”.
29... English
Lamp
Allow it to cool down
before changing lamp!Lamp Changing Procedure:
1.Turn off the power to the projector by pressing the Power button.
2.Allow the projector to cool down at least 30 minutes.
3.Disconnect the power cord.
e a screwdriver to remove the screw from the cover.n
5.Push up and Remove the cover.o
6.Remove the 3 screws from the lamp module.p
7.Pull out the lamp module.q
To replace the lamp module, reverse the previous steps.injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.
123
4
o F (5~ 35o C)
o F (-20~60o C)
Remark : “*”compression computer image.。