DVI说明书-英文中性
dvi 矩阵说明书中性
DVI MATRIX 高清数字矩阵说明书《高清矩阵切换系统用户手册》以16x16矩阵的使用方法作为说明，并可作为其它型号矩阵的使用参考。
本手册只作为用户操作指示，不作为维修服务用途。
其所述功能截止日期为20011年11月，此日期后的功能或相关参数有改变，将另作补充说明，详细可向各经销商查询。
本手册为生产商版权所有，未经许可，任何单位或个人不得将本手册之部分或其全部内容作为商业用途。
本手册版权所有者受《中华人民共和国著作权法》及其他知识产权法规保护。
未经书面许可不得复印或散布。
1．概述高清数字矩阵切换器是专门为高清数字信号的切换而设计的高性能智能矩阵设备，用于将各路数字视频输入信号切换到任意视频输出通道上，主要应用于监控电视工程、多媒体会议厅、大屏幕显示工程、电视教学、指挥控制中心等场合。
本产品带有断电现场保护、LCD 液晶显示、红外和计算机RS232远程控制等功能。
本说明书以视频16×16矩阵的使用方法为例展开说明，其它型号矩阵使用方法，参照16×16的使用说明即可。
高清数字矩阵切换器有三种规格：A型为标准1U机箱（最大8×8），B型为标准4U机箱(最大16×16)，C型为标准7U机箱(最大32×32)，D型为标准10U机箱（最大64×64）。
4种类型的矩阵安装操作方法相同，典型拉线图如下：每个系列的输入输出通道数都是可选的，如下表：A系列（1U）2．性能特点⊙兼容DVI 1.0。
⊙自动EDID，所有输入口的EDID信息自动同步到第1个输出显示单元的EDID。
⊙输入内建自适应均衡器，输出预加重，支持DVI线长到15m(AWG24)。
⊙断电现场保护。
⊙输入信号丢失LED指示。
⊙插卡式工业机箱，输入输出独立插卡，灵活可靠（A型除外）。
⊙带RS232接口，可远程计算机操作。
⊙前面板液晶显示，独立按键操作，清晰直观。
⊙支持红外遥控。
3.技术指标4.安装后视图：A型上面一排从左至右分别为8路输入，下面一排从左至右为8路输出。
DVI无压缩说明书
DVI无压缩光端机说明Ver:1.0广播级的品质、民用级价格全数字、零压缩、零延迟支持传送速率为10Gbps最高分辨率：1920*1080@120HZ 4K*2K@30Hz支持3D支持HDCP标准支持7.1 声道PCM环绕声音和压缩音频兼容DVI信号的传送支持DVI接口热插拨低能耗,长距离,即插即用，无需设置一、简介：此产品是一款广播级的高清DVI光端机，通过专利转换芯片将DVI信号,转换成10G的差分信号，通过光模块及光纤进行发送和接收，实现对DVI高清多媒体信号的远距离传输，通过不同传输距离的光模块，实现最远可达60KM的远距离传输，此传输产品是一款无损失、无延时传输，适用于高清远距离传输的各种要求。
支持DVI 1.4 高清及3D视频信号传送, 可反传EDID，支持HDCP，分辨率分别可达720p/60Hz, 1080i/60Hz, 1080p/30Hz,1080p/60Hz, 1080p/120Hz等，支持7.1 声道PCM 环绕声音和压缩音频，兼容DVI信号的传输，支持DVI接口热插拨，低能耗,长距离，无压缩, 零延迟，即插即用，兼容强，能实现更精确显示。
提供850nm多模和1310nm单模光纤型号。
DVI光端机是发送器与接收器组成，实现DVI视频图像进行完美的像素对像素的传输。
产品紧凑、小巧的外壳允许隐蔽地安装在平板显示器后面。
DVI光端机是大型、完整的系统光纤传输产品的组成部分，它与其它的DVI、VGA光端机组成一系列高清视频信号的延长。
可实现点对点的各种方案的传输。
可通过光分路器实现1个发送带多台接收的传输方式。
DVI光端机非常适用于需要以最高的品质长距离传输高分辨率内容的广泛应用环境。
由于光纤传输固有的安全性各抗干扰性，光纤应用更适用于政府、军队和医疗环境。
DVI光端机应用了行业标准LC型连接器连接。
二、产品名称：DVI光端机三、产品型号：光发送器：DVI-H-T 光接收器：DVI-H-RDVI-H-T是光发送器，ZY-DVI-H-R是光接收器，二个设备配合使用，可实现经DVI-H-T光发送器把DVI音视频信号经光缆长距离发送给ZY-DVI-H-R光接收器，在不经过对信号进行任何压缩处理后，高保真输出“原装”的音视频信号。
DVI介绍
DVI-dDVI接口是1999年由数字显示工作组DDWG（Digital Display Working Group）推出的接口标准，是Digital Visual Interface的缩写，其造型是一个24针的接插件。
是专为LCD显示器这样的数字显示设备设计的。
DVI接口有多种规格，分为DVI-A、DVI-D 和DVI-I。
DVI-A其实就是VGA接口标准，只是换汤不换药而已。
所以带有DVI 接口的液晶显示器也并不一定就是真正的数字液晶显示器。
DVI-D则实现了真正的数字信号传输。
而DVI-I通吃上述两个接口，当DVI-I接VGA设备时，就是起到了DVI-A的作用；当DVI-I接DVI-D设备时，便起了DVI-D的作用。
为了兼容传统的模拟显示设备，现在的大部分显卡都采用了24只数字信号针脚和5只模拟信号针脚的DVI-I接口。
注：（图片中左为DVI-D，右为DVI-I）DMI百科名片HDMI，高清晰度多媒体接口（英文：High Definition Multimedia Interface）是一种符合高清时代标准的数字化视频/音频接口技术，可用于机顶盒、DVD播放机、个人电脑与电视机。
业界于2002年12月9日正式发布了HDMI 1.0版标准，于2010年3月4日发布HDMI规格版本1.4a。
HDMI可以同时传送音频和影音信号，能高品质地传输未经压缩的高清视频和多声道音频数据，最高数据传输速度为5Gbps。
同时无需在信号传送前进行数/模或者模/数转换。
HDMI规格可搭配宽带数字内容保护（HDCP），以防止具有著作权的影音内容遭到未经授权的复制。
目录规范标识中文标识产生背景功能特点接头分类英文定义测试规范连接电脑展开编辑本段规范标识2002年4月，日立、松下、飞利浦、索尼、汤姆逊、东芝和Silicon Image七家公司联合组成HDMI组织。
HDMI Licensing, LLC于2010年3月4日代表HDMI原始开发成员发布HDMI规格版本1.4a，其中特色包括3D应用的关键增强功能，加入了用于广播内容的强制3D格式，以及称为Top-and-Bottom的3D格式。
拼接处理器E系列用户使用手册V1.1-中性-20170422
预布局
1 场景与轮巡
场景
2
轮巡
高级应用
2
滚动字幕
2
边框补偿
2
可视化设置
2
信号源裁剪
台标
3
底图
4 用户管理
新增帐户
4
权限设置
修改帐户信息
4
删除帐户
4 设备管理
5
设备状态图形化显示
设备软关机
5
报警管理
系统工具
8
升级
8
数据备份恢复
12
EDID
自定义分辨率
15
系统通讯配置
15 附录 15 16 术语表
16 16
2U 设备后面板：2 个输入槽位，2 个输出槽位，1 个控制槽位，1 个回显槽位，1 个电源。
3U 设备后面板：4 个输入槽位，4 个输出槽位，1 个控制槽位，1 个回显槽位，1 个电源。
6U 设备后面板：11 个输入槽位，6 个输出槽位，2 个控制槽位，1 个回显槽位，2 个电源。
8
产品结构 8U 设备后面板：15 个输入槽位，10 个输出槽位，2 个控制槽位，1 个回显槽位，2 个电源。
14U 设备后面板：21 个输入槽位，18 个输出槽位，2 个控制槽位，1 个回显槽位，4 个电 源。
13
产品结构 26U 设备后面板：42 个输入槽位，36 个输出槽位，2 个控制槽位，2 个回显槽位，4 个电源。
14
软件简介
软件简介
简介
拼接控制系统是基于 B/S 架构设计的软件操作平台。通过登录网页，进行简单的配置操作， 即可实现拼接墙显示功能。 支持的浏览器如下：
输出板卡槽位，可插入 DVI、HDMI、HDBaseT、NPC（预监）等板卡。
DVI分配器,一进二出说明书
产品描述:
深圳市圣大奥维科技发展有限公司专业研发生产VESION品牌的一进二出DVI 1S2，DVI 分配器可以使机顶盒、DVD放机、D-VHS放像机和其他的HDTV设备通过一个DVI输出同2个或者更多的HDTV显示器连接。
它是一个灵活的集线器，适用于多种显示器。
如果把2个或者多个HDMI分配器连接起来，可以组成一个更大的分配器。
产品特点：
●从一个DVI Input 到 2 个DVI Outputs
●采用外接式设计，无内插卡式的系统兼容性问题
●讯号传输达10 公尺( 有效距离)
●适用具DVI 端口之高分辨率屏幕
●支援UXGA ，频宽达165MHz
●可串接扩充，增加屏幕显示数量
●支持HDTV 高画质电视1920x1200 高分辨率。
产品应用
● 公共视讯系统( 证券公司、期货市场、金融证券等)
●高质量多媒体展示、简报
● 视讯会议(Video Conference)
●屏幕测试与烧机(Monitor testing and burn-in)
●功耗：2W。
DVI分配器用户手册
ESC: 返回键，退出当前菜单或操作。
6 主界面
分配器开机后，LCD 屏显示主界面如下：
公司
限
有
技
①
电子科 图 6-1 主界面 瓦 ②诺 安
输入源状态：在未连接时为图中①所示且 不停闪烁，在连接状态时为图中②所示， 且不闪烁。
西
输出源状态：在未连接时界面显示如
“1”，在连接状态时为界面显示如“4”。
电磁干扰：设备应远离磁铁、马达及变压器。
防潮：请将设备置于干燥、干净的环境中。如有液体浸入，请立即拔掉电源 插头。
远离易燃易爆危险物品。
公司
技有限 禁止液体、金属碎片浸入机器内部，以免引起安全事故。
子科
电
诺瓦
西安
2
2 概述
DVI 分配器 D-DV18 用户手册
版权
本手册版权归西安诺瓦科技所有，任何个人或单位未经书面许可，不得以任何形式对文本内容作复制、摘
录。
司
商标
公
是诺瓦科技的注册商标。
技有限
子科
电
诺瓦
西安
DVI 分配器 D-DV18 用户手册
目录
1 安全声明 .............................................................................................................................................. 2
8 菜单语言 .............................................................................................................................................. 7
DVI CABLE 说明
因此像素频宽或像素传输速率计算法如下。参考表2.1，以SXGA为例，
DISM是由日本的JEIDA协会(Japan Electronic Industry Development Association)所推广的，是Molex主导DVI的一个竞争对手。为了加强其技术应用面，DISM可以使用不同的视讯信号传输技术。不论是TMDS、LVDS甚至类似TMDS两个连结的LDI标准，及Sony的GVIF(Giga-bit Video Interface)也可适用。
此外，在线材的载具上，TMDS是使用差分(Differential)的传输技术，除了可有效的降低同模噪音(Common Mode Noise)之干扰，并可仅用一半的电位变动(VSwing)来传输实际峰值大小为2倍VSwing的讯号，如图2.2所示。这样不但可以减少传输的功率销耗，合省电原则，也可以降低EMI的干扰。
3.3
206.17
HDTV
1920
1080
60
0.05
130.96
3.05
190.9
QXGA
2048
1536
60
0.05
198.68
2.01
125.83
CRT Frame Rate 60 Blanking GTF
VGA
640
480
60
0.295
26.14
15.3
956.39
SVGA
DVI分配器规格书英文版
AR
T
H C E
CO
.,L
. D T
The same as that of DVI input interface.
-20~60℃
2.9Kg 1.5M 1.5M
www.novastar.tech
4
Input Source
DVI IN
Output Interface
'A I DVI OUT 1~8 X
RS232 USBNN NhomakorabeaO
T S VA
AR
T
H C E
CO
.,L
. D T
DVI signal input
8-way DVI output
Control Interface
Serial port control USB control interface
resolution.
Outputs
Port DVI OUT Quantity 8 Resolution
T S Overall Specifications VA O Overall Power N 15W N Consumption 'A I X
Operating Environment Temperature Net Weight USB Line DVI Line
5) Configure LCD display and shortcut key for easy-to-use; 6) USB control interface supports on-line program upgrade.
function, having simple and easy-to-use LCD operating interface, and
DVI控制台USB接口计算机控制集说明书
q One DVI console controls up to four USB interface computers qDVI-D KVM cable set - Includes two 44-pin Custom KVM cables (4ft & 6ft) to connect up to four computers q Fully compliant with DVI specification (Digital only) q Supports multi-function and wireless mouse/keyboard qAudio enabled – full bass response provides a rich experience for 2.1 channel surround sound systems q Video resolution – up to 1920 x 1200 @60Hz; 1080p Full HD q Auto Scan Mode for monitoring all computers qMultiplatform support – Windows®, Linux®, Mac, FreeBSD and Oracle® Solaris q Console mouse port emulation/bypass feature supports most mouse drivers andmultifunction miceq Hot Pluggable - Add or remove computers for maintenance without powering down the switchq HDCP compliant q Video DynaSync™q Power on Detection - Automatically switches to the next powered-on computer when the other is turned offq Computer selection via front panel pushbuttons, hotkeys, and mouse switching function qUSB 2.0 mouse port can be used for USB hub and USB peripheral sharing q Complete keyboard emulation for error-free booting q Mac/Sun keyboard support and emulation q Firmware Upgradableq Plug & Play - No software installation required4-Port DVI KVM SwitchThis IOGEAR DVI KVM Switch GCS1004 allows users to access up to four computers from a single USB keyboard, USB mouse, and DVI monitor. It supports resolutions up to 1920 x 1200 @60Hz. With IOGEAR's DynaSync™, there is no more delay or change of video resolution when switching between or booting the computers. It also comes equipped with an audio line out and has power on detection – it will automatically switch to the next powered-on computer when the other is turned off. It also allows each computer to access any peripherals connected to the USB 2.0 port and with its audio enabled, users can listen to the audio output of each computer on one set of speakers.The setup is quick and easy; users just need to plug the cables into their appropriate ports. There is no software to configure. Since GCS1004 intercepts keyboard input directly, it supports multiple computing platforms (PC x86 / x64, Macintosh PowerPC, and Oracle® Solaris Microsystems Sparc).There are three convenient methods users can use to access the computers: port selection push buttons located on the unit's front panel; hotkey combinations entered from the keyboard;and mouse port-switching by simply double-clicking on the scroll wheel of a USB mouse to change the ports.4-Port USB DVI KVM SwitchGCS1004SpecificationsqConsole:q 1 DVI displayq 1 set of USB keyboard and mouseq Speakers (optional)qq Computers:q 1 DVI Portq 2 USB Portsq Audio ports (optional)q Computers with sound supportqq Operating Systems:q Windows® XP, Windows Vista®,Windows® 7, Windows® 8,Windows® 8.1q Mac OS 9 to 10.xq Oracle® Solarisq Linux®, Unix and other USBsupported systems**Additional drivers and support may beneededProduct Requirementsq 1 x GCS1004 4-Port USB DVI KVMSwitchq 1 x 4ft 44-pin Custom KVM Cable setq 1 x 6ft 44-pin Custom KVM Cable setq 1 x Power Adapterq 1 x User Manualq 1 x Warranty CardPackage ContentsFunction GCS1004Dimensions GCS1004Unit DimensionsHeight 1.06" (2.69cm)Depth 3.25" (8.26cm)Length7.88" (20.02cm)Unit Package DimensionsWidth11.25" (28.58cm)Height 6.94" (17.63cm)Depth 4.00" (10.16cm)Master CartonWidth12.81" (32.54cm)Height15.06" (38.18cm)Depth11.81" (30.00cm)Master Carton Qty.6WeightMaster Carton Wt.24.50lbs (11.11kg)Unit Pack Wt. 3.85lbs (1.75kg)Unit Wt. 1.10lbs (0.499kg)19641 Da Vinci, Foothill Ranch, CA 92610 GCS1004© 2014 IOGEAR®IOGEAR, the IOGEAR logo, are trademarks or registered trademarks of IOGEAR. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other brand and product names are trademarks or registered trademarks of their respective holders. IOGEAR makes no warranty of any kind with regards to the information presented in this document. All information furnished here is for informational purposes only and is subject to change without notice. IOGEAR assumes no responsibility for any inaccuracies or errors that may appear in this document.4-Port USB DVI KVM Switch。
三芯DVI-D单链接信号扩展器说明书
DVI over Cat5/6 Extender, Wall Plate Receiver for Video, DVI-I Single Link, RJ45, Up to 200 ft. (60 m)MODEL NUMBER:B140-1A0-WP-1Receiver wallplate extends a DVI-D single-link signal via one Cat5e/6 patch cable up to 200 ft. with a Tripp Lite B140-002 or B140-004 extender/splitter transmitter unit (sold separately).DescriptionThe B140-1A0-WP-1 DVI over Cat5/6 Extender works in tandem with a B140-002 or B140-004extender/splitter transmitter unit (sold separately) to extend a DVI-D single-link signal over a singleCat5e/6 Ethernet cable. It can extend a 1920 x 1080 (60 Hz) signal up to 150 feet (45.7 meters) and a 1024 x 768 signal (60 Hz) up to 200 feet (61 meters). It's ideal for digital sign applications in schools, churches, trade shows, retail settings and anywhere else a high-resolution DVI signal needs to be delivered over a long distance.Just connect a B140-002 or B140-004 transmitter to the DVI source using a DVI cable, such as the P561-Series. Connect the B140-1A0-WP-1 to the transmitter using a Cat5e/6 cable (for best results, we recommend N202-Series 24 AWG solid-wire Cat5e/6 cable) and connect to the display using a DVI cable. To expand the range and the number of displays, add up to three B140-110 remote repeaters and an active receiver to each channel for a total of four displays per channel. A 1920 x 1080 (60 Hz) signal can be extended up to 125 feet (38.1 meters) to the next unit in the chain and a 1024 x 768 signal (60 Hz) up to 175 feet (53.3 meters).The B140-1A0-WP-1 works with all operating systems. Its plug-and-play technology means no software or drivers need to be downloaded and installed. Built-in equalization control allows for manual adjustment of the video image. Complies with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases.FeaturesExtend DVI-D Signal via Cat5e/6 Patch Cable Up to 200-ft. (61 m)Ideal for digital sign applications in schools, churches, trade shows and retail settingsqWorks in tandem with B140-002 or B140-004 extender/splitter transmitters (sold separately)qExtends a 1920 x 1080 (@ 60 Hz) signal up to 150-ft. (45.7 m)qExtends a 1024 x 768 signal (@ 60 Hz) up to 200-ft. (61 m)qEven More Distance and FlexibilityAdd up to 3 B140-110 remote repeaters and an active receiver for total of 4 displays per channelqCan extend 1920 x 1080 (@ 60 Hz) signal up to 125-ft. (38.1 m) to next unit in chainqCan extend 1024 x 768 (@ 60 Hz) signal up to 175-ft. (53.3 m) to next unit in chainq HighlightsSupports video resolutions up to 1920 x 1080, including 1080pqEasy RJ45 connector onwallplate backqBuilt-in equalization control forimage adjustmentqCompatible with all majoroperating systemsqPlug and play—no software ordrivers to downloadqSystem RequirementsPackage IncludesB140-1A0-WP-1 DVI overCat5/6 ExtenderqExternal power supply w/NEMA 1-15P plug and 5-ft. (1.52 m)cord (Input: 100-240V, 50/60Hz, 0.5A; Output: 5V, 2A)qScrewdriver for adjustingequalizationqMounting hardwareqOwner's manualqSpecificationsConvenient Plug-and-Play Setup No software or drivers requiredq Compatible with all major operating systemsq Easy RJ45 connector on back—no 110 punchdown necessary q HDCP compatibleq Built-in equalization control for image adjustmentqTAA CompliantComplies with the Federal Trade Agreements Act (TAA) for GSA Schedule purchasesq© 2023 Eaton. All Rights Reserved. Eaton is a registered trademark. All other trademarks are the property of their respective owners.。
OMRON XM4M DVI连接器 说明书
Ӵ䗕催ߚ䕼⥛㾚乥ֵোDŽヺড়DVI ˄Digital Visual Interface ˅㾘Ḑⱘྚ啭DVI 䖲఼ƽϡҙᰃ᭄ᄫ㾚乥ֵো˄TMDS ˅ˈ䖬㛑ৠᯊՓ⫼ҹᕔⱘᢳֵো˄RGB ˅DŽƽᢳষϞথ᳔2.5GHz ᏺᆑᗻ㛑ⱘྚ啭DVI 䖲఼DŽƽৃᬃᣕᮄϔҷᆑᏺⱘ᳔9.9Gbps ˄ঠ䫒˅ⱘᆑᏺ᭄Ӵ䗕DŽƽ催䗳᭄Ӵ䗕Ёϡৃ㔎ⱘEMI ᇍㄪሣ㬑гᅠDŽƽ᭄᳝ᄫൟǃ᭄ᄫ/ᢳ݅⫼ൟ2⾡㉏ൟDŽƵ⫼䇁䇈ᯢƽDVIDigital Visual Interface 的缩写。
计算机和显示屏的一种连接规格。
可通过计算机向显示屏直接传送数字信号。
ƽTMDSTransition Minimized Differential Signaling 的缩写。
在DVI 中采用的显示屏影像信号的数字传送方式。
ƽRGBR ：Red （红）、G ：Green （绿）、B ：Blue （蓝）3种影像信号。
ƽbpsBits Per Second 的缩写。
1秒内可传送数据速度的单位。
1bps 是指在1秒内可传送1位数据的意思。
ƽԡ计算机处理信息的最小单位。
ƽEMIElectromagnetic Interference （电磁干扰）的缩写。
Ƶ⾡㉏＊外壳颜色是黑色时，型号末位是1。
Ƶ乱ᅮؐ/䋼ᴤƵ㛑ᗻ/໘⧚ヺড়RoHS乍Ⳃ㉏ൟ᭄ᄫൟ᭄ᄫ/ᢳ݅⫼ൟᵕ᭄24极29极ッᄤᔶ⢊DIP L 型买㡆黑色或天然色乱ᅮ⬉⌕ 1.5A 乱ᅮ⬉य़AC40V㾺⬉䰏30m Ω以下（DC20mV 以下、100mA 以下时）㒱㓬⬉䰏1,000M Ω以上（DC500V 时）㗤⬉य़DC500V 1min （漏电流0.5mA 以下）Փ⫼⏽ᑺ－20～＋85℃ֱᄬ⏽ᑺ－20～＋85℃含玻璃纤维PBT 树脂（UL94V-0）/黑色或天然色Ⲫᄤ含玻璃纤维PBT 树脂（UL94V-0）/黑色或天然色㾺⚍㾺䚼铜合金/镍底镀金（0.76μm ）ッᄤ䚼铜合金/镍底镀锡（3.0μm ）ԧ钢/镀镍ᅮӊ钢/镀镍ഄ䜡ӊ铜合金/镀锡XM4MDVI 䖲఼Ƶᔶሎᇌ˄ऩԡ˖mm ˅Ƶッᄤ䜡㕂ƽ᭄ᄫ/ᢳ݅⫼ൟⱘッᄤ䜡㕂注.数字型无C1～C5。
Extron Electronics DVI-RGB 200 说明书
DVI to Analog RGB Video Interface
User Guide
Interfaces
68-1791-01 Rev. A 10 10
Safety Instructions • English
This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock.
Réparation-maintenance • Faire exécuter toutes les interventions de réparation-maintenance par un technicien qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.
DVI KVM HDBaseT Extender 用户手册说明书
*Preferred1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this product near water.6. Clean only with a dry cloth.7. Do not block any ventilation openings. Install in accordance with the manufacturer’sinstructions.8. Do not install or place this product near any heat sources such as radiators, heatregisters, stoves, or other apparatus (including amplifiers) that produce heat.9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarizedplug has two blades with one wider than the other. A grounding type plug has twoblades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.10. Protect the power cord from being walked on or pinched particularly at plugs,convenience receptacles, and the point where they exit from the apparatus.11. Only use attachments/accessories specified by the manufacturer.12. To reduce the risk of electric shock and/or damage to this product, never handle ortouch this unit or power cord if your hands are wet or damp. Do not expose thisproduct to rain or moisture.13. Unplug this apparatus during lightning storms or when unused for long periods of time.14. Refer all servicing to qualified service personnel. Servicing is required when theapparatus has been damaged in any way, such as power-supply cord or plug isdamaged, liquid has been spilled or objects have fallen into the apparatus,the apparatus has been exposed to rain or moisture, does not operate normally,or has been dropped.15. Batteries that may be included with this product and/or accessories should never beexposed to open flame or excessive heat. Always dispose of used batteriesaccording to the instructions.Gefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications. Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for ninety (90) days from the day of reshipment to the Buyer.This warranty is in lieu of all other warranties expressed or implied, including without limitation, any implied warranty or merchantability or fitness for any particular purpose, all of which are expressly disclaimed.1. Proof of sale may be required in order to claim warranty.2. Customers outside the US are responsible for shipping charges to and from Gefen.3. Copper cables are limited to a 30 day warranty and cables must be in their originalcondition.The information in this manual has been carefully checked and is believed to be accurate. However, Gefen assumes no responsibility for any inaccuracies that may be containedin this manual. In no event will Gefen be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. The technical information contained herein regarding the features and specifications is subject to change without notice.For the latest warranty coverage information, refer to the Warranty and Return Policy under the Support section of the Gefen Web site at .Technical Support(707) 283-5900 (800) 472-55558:00 AM to 5:00 PM Monday - Friday, Pacific TimeEmail*****************WebMailing AddressGefenCore Brands, LLCc/o Customer Service1800 S McDowell BlvdPetaluma, CA 94954 USAProduct RegistrationRegister your product here: /kvm/Registry/Registration.jspDVI KVM HDBaseT™ Extender w/ USB, RS-232, and POH is a trademark of Gefen, LLC.© 2016 Core Brands, LLC. All Rights Reserved. All trademarks are the property of their respective owners.Gefen, LLC reserves the right to make changes in the hardware, packaging, and any accompanying documentationwithout prior written notice.This product uses UL listed or CE-compliant power supplies.PbFeatures• Extends DVI, USB, RS-232, and 2-way Audio over a single CAT-5e◦1080p Full HD (1920 x 1080 @ 60Hz, 4:4:4, 12-bit), up to 330 feet/100 meters ◦1080p Full HD (1920 x 1080 @ 60Hz, 4:4:4, 8-bit), up to 495 feet/150 meters◦WUXGA (1920 x 1200 @ 60Hz, 8-bit), up to 495 feet/150 meters• Extends HDMI**, USB, RS-232, and 2-way Audio over a single CAT-5e ◦4K Ultra HD (3840 x 2160 @ 60Hz, 4:2:0, 8-bit), up to 330 feet/100 meters◦4K Ultra HD (3840 x 2160 @ 30Hz, 4:4:4, 8-bit), up to 330 feet/100 meters◦4K DCI-Cinema (4096 x 2160 @ 30Hz 4:4:4, 8-bit), up to 330 feet/100 meters ◦1080p Full HD (1920 x 1080 @ 60Hz, 4:4:4, 12-bit), up to 330 feet/100 meters ◦1080p Full HD (1920 x 1080 @ 60Hz, 4:4:4, 8-bit), up to 495 feet/150 meters◦WUXGA (1920 x 1200 @ 60Hz, 8-bit), up to 495 feet/150 meters• HDMI Features Supported:◦HDMI 2.0 up to 4K 60Hz, 4:2:0, 8-bit color◦HDCP 2.2 and 1.4◦12-bit Deep Color◦LPCM 7.1 audio, Dolby Atmos®, Dolby® TrueHD, DTS:X™, and DTS-HD Master Audio™ pass-through◦3DTV pass-through◦CEC pass-through◦Lip Sync pass-through• Analog L/R Stereo Audio extension from Sender to Receiver and from Receiver to Sender• Receiver audio input accommodates a microphone or a line level audio source• POH (Power Over HDBaseT™) feature provides power to Sender unit over the link cable - only the Receiver needs external power• Advanced EDID Management via Gefen Syner-G™ software• Link Quality Monitoring via Gefen Syner-G™ software• In-field firmware update via USB, using Gefen Syner-G™ software• Locking power connector• 1U tall, half-rack-width enclosures can be:◦Surface-mounted◦Installed in a standard 19-inch rack using the EXT-RACK-1U-GRY rack tray (available separately)◦Placed on a shelf** Use Gefen DVI to HDMI cables•1 x DVI KVM HDBaseT™ Extender w/ USB, RS-232, and POH - Sender unit •1 x DVI KVM HDBaseT™ Extender w/ USB, RS-232, and POH - Receiver unit •1 x 6 ft. DVI cable (M-M)•2 x 6 ft. 3.5mm mini-stereo cable (M-M)•1 x 6 ft. Dual-Link DVI cable (M-M)•1 x 6 ft. USB A-B cable (M-M)•8 x Self-Adhesive Rubber Feet •4 x L-Shaped Surface-Mounting Brackets •8 x 6mm M3 Phillips flat head machine screws, 0.5mm pitch, for use with EXT-MP-C01•4 x 5mm 6-32 Phillips flat head machine screws, for use with EXT-RACK-1U •1 x 48V/1A DC power supply with locking plug •1 x IEC AC power cord with interchangeable connectors (US, UK, EU, AU)• 1 x Quick-Start GuideHDCP DCI, 4096 x 2160, 30Hz1 Getting StartedIntroduction (2)Sender Unit (2)Receiver Unit (4)Installation (7)Connection Instructions (7)Application Diagram (8)2 Basic OperationLED Status (12)Audio Connections (13)DIP Switch Configuration (15)EDID Management (16)EDID Lock (17)HDCP (17)Long-Reach Mode (18)RS-232 Interface (19)RS-232 Interface (19)3 Advanced OperationUsing Syner-G™ (24)Verifying the USB Driver (24)Downloading an EDID (26)Uploading an EDID (29)Copying an EDID (31)Viewing an EDID (33)4 AppendixDefault Settings (40)Sender Unit DIP Switches (40)Receiver Unit DIP Switches (40)Updating the Firmware (41)Network Cable Diagram (47)Rack Tray Installation (48)Specifications (49)Index (51)This page left intentionally blank.This page left intentionally blank.1 Getting StartedSee Long-Reach Mode (page 18) for more information.►Audio (see Audio Connections (page 13) for more information)4. Connect a 3.5mm mini-stereo cable from the Audio In port on the Sender unitto the audio source.5. Connect a pair of powered speakers (or another audio output device) to theAudio Out port on the Receiver unit.6. Connect a line-level or mic-level input to the Audio In port on the Receiver unit.If using a mic-level input, then set the Mic / Line switch, on the Receiver unit, to the Mic position.Application Diagram2AudoABAudoThis page left intentionally blank.This page left intentionally blank.2 Basic OperationIn order to get the audio from the Receiver unit to the computer, connect a 3.5mm mini-stereo cable from the Audio Out port on the Sender unit to the on the computer.DVI KVM HDBaseT Extender S w/ USB, RS-232, 2-way Audio, and POH USB AudioIn Out Link USB Host Interface DVI-D In Connect to Line Out on computer Connect to Line In on computer ™USB EXT-DVIKA-HBT2-R RS-232LineMic In Out Link DVI-D Out Audio Mic / Line switch Connect to audio source Receiver unitIn the diagram below, the USB devices have been removed from the Sender and Receiver unit, for purposes of clarity. Arrowheads indicate the audio signal path. Figure 2.1 - Speaker and audio connections USB USB Out Link DVI-D Out 1234Audio Connect to computer speakers Sender unitAudio InAudio source(line-level)Audio OutAudio OutAudio InComputerLineMicIn Out Link Audio ON WE 1 2 3 4DIP switches DIP switchesO N1 2HDCPThis feature allows HDCP content to either be passed-through or disabled on the input. Disabling this feature does not decrypt HDCP content.Receiver unit HDMI OutSender unit Automation Control DeviceHDMI InThis page left intentionally blank.This page left intentionally blank.3 Advanced OperationUSB driver5.Click the Save As button. 6. The Windows Save File dialog will be displayed. Select the desired folder and specifythe name of the file in the File name field, within the Save File dialog. Make sure to specify the .bin extension to the filename.Version Info fieldEDID file nameSave button Click the Save button.4. Click the Browse button.8. Click the Upload button.9. In the lower-left corner of the interface, the “Uploading...” message will appear as theEDID is uploaded. Once the operation is complete, the “Upload Complete.” message will be displayed.4. Click the Copy EDID to drop-down list to select the location to where the EDIDwill be copied. The EDID can by copied to the Local EDID or to an EDID bank.In this example, since we copied the downstream EDID to the local EDID, the “Copy result: Downstream stored to local.” message is displayed.Note that the display, which is connected to the computer, is also available in the drop-down list. In this way, we can download, view, and/or edit the EDID from the display (sink) device.4. Click the View button.EDID tabsDetails buttonEDID Summary window will be displayed. Use the horizontal and vertical scroll bar, as needed, to view the EDID information.Scroll barScroll bar10. Double-click the window title bar of the detached EDID Summary to reattach it to themain window. it to the main Syner-G window. 11. To close the EDID Summary corner of the EDID Summary window or click the button in the main Syner-G window.“separate” button“X” buttonThis page left intentionally blank.This page left intentionally blank.4 Appendix。
IOGEAR 4-Port 双视图双链DVI KVM分屏开关用户手册说明书
GCS1642/GCS1644/GCS1642X©2018 IOGEAR. All Rights Reserved. PKG-M1087-g / M1088-gIOGEAR, the IOGEAR logo, are trademarks or registered trademarks of IOGEAR. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other brand and product names are trademarks or registered trademarks of their respective holders. IOGEAR makes no warranty of any kind with regards to the information presented in this document. All information furnished here is for informational purposes only and is subject to change without notice. IOGEAR assumes no responsibility for any inaccuracies or errors that may appear in this document.Package Contents4 System Requirements5 GCS1642 Overview6 GCS1644 Overview8 Single Stage Installation10 Quad View (DDC Mode)15 LED Indication17 Port Switching 18 Port Switching via Hotkeys19 Auto Scanning21 Hotkey Setting Mode (HSM)22 Mac Keyboard Emulation24Sun Keyboard Emulation25 Factory Default Hotkeys Settings26 The Firmware Upgrade Utility27 Before you Begin27 Starting the Upgrade28 Upgrade Succeeded31 Upgrade Fail32 Federal Communications Commission(FCC) Statement33 CE Statement33 Limited Warranty34 Contact3531 x 2/4-Port Dual View Dual Link DVI KVMP Switch with Audio2/4 x Dual Link DVI KVM Cables (2 for GCS1642 / 4 for GCS1644) 2/4 x Dual Link DVI Cables (2 for GCS1642 / 4 for GCS1644)1 x Power Adapter1 x Installation Guide1 x Warranty CardNote:GCS1642X does not include KVM and DVI cables.4Console–Two displays with DVI inputs– A Keyboard and MouseComputer–Computers with DVI outputs–An open USB portOptional Audio–Analog audio connections for speakers and mic.57Rear View1. DDC Port (Daisy Chain Port)2. DC Power Jack3. Console USB Mouse Port4. Console USB Keyboard Port5. Console DVI Video Port B6. Console DVI Video Port A7. DDC Switch (Host/Client)8. USB 2.0 Peripheral Sharing Port 9. Console Mic. Connection 10. Console Audio Connection 11. CPU2 DVI Video Port 2B 12. CPU2 DVI Video Port 2A 13. CPU2 USB Connection14. CPU2 Mic. Connection 15. CPU2 Audio Connection 16. CPU1 DVI Video Port 1B 17. CPU1 DVI Video Port 1A 18. CPU1 USB Connection 19. CPU1 Mic. Connection 20. CPU1 Audio Connection8GCS1644 OverviewFront View1. Port 1 Pushbutton2. Port 2 Pushbutton3. Mode Button4. Port 3 Pushbutton5. Port 4 Pushbutton6. Front Panel Console Mic. Connection7. Front Panel Console Audio connection8. Front Panel USB 2.0 Peripheral Sharing PortRear View1. DDC Port (Daisy Chain Port)2. DC Power Jack3. Console USB Mouse Port4. Console USB Keyboard Port5. Console DVI Video Port B6. Console DVI Video Port A7. DDC Switch (Host/Client)8. USB 2.0 Peripheral Sharing Port9. Console Mic. Connection10. Console Audio Connection 11. CPU4 DVI Video Port 4B12. CPU4 DVI Video Port 4A13. CPU4 USB Connection14. CPU4 Mic. Connection15. CPU4 Audio Connection16. CPU3 DVI Video Port 3B17. CPU3 DVI Video Port 3A18. CPU3 USB Connection19. CPU3 Mic. Connection20. CPU3 Audio Connection21. CPU2 DVI Video Port 2B22. CPU2 DVI Video Port 2A23. CPU2 USB Connection24. CPU2 Mic. Connection25. CPU2 Audio Connection26. CPU1 DVI Video Port 1B27. CPU1 DVI Video Port 1A28. CPU1 USB Connection29. CPU1 Mic. Connection30. CPU1 Audio Connection9Step 1Please make sure your source devices and display are powered off before you start.Step 2Plug the power adapter into the power outlet and connect it to the DC power jack from the KVM.10Step 3Connect the DVI cables from your monitors to the console DVI port A and B. Port A will be your main monitor and Port B will be your extended desktop monitor.1112Step 4Connect your USB keyboard and mouse to the console USB keyboard port and console USB mouse port.1314Step 6Final StepTurn on your source devices.To expand your installation from Dual View displays to Quad view displays, you can use the DDC Mode port to connect two GCS1642 / GCS1644 units together. After doing so, you will be able to configure the quad displays video settings on the computer in extended mode or Mirrored mode.To set up DDC mode, power off all devices, refer to the installation diagram on the next page.1. Connect all the computers to the Host as described in Hardware Setup, Cable Connection on page 18.2. On the Client, using two custom DVI Dual Link cables, plug the DVI connectors into the DVI sockets Aand B in the same KVM port section of the switch.3. At the other end of the two custom DVI Dual Link cables, plug the monitor cable into the respectiveports on the computer.4. Repeat steps 2 and 3 for all computers.5. On the rear of the second GCS1644, set the DCC switch to Client.*6. On the rear of the primary GCS1644, set the DCC switch to Host.7. Plug the console monitors into the DVI console ports located on the Host’s and Client’s rear panel.8. Using an RJ-45 cable, connect the DCC port of the Host to the DCC port of the Client.9. Power up the installation: plug in the power cord for the Host and Client, then power on both. Afterboth units are up, power on the computer/video source devices.Note:1. In DCC mode the Client’s front panel pushbuttons are disabled and it takes all commands directly from the Host.2. Setting the DCC switch to Client will disable all front panel pushbuttons on that switch.1517Simply press the front panel Pushbutton from the multimedia KVMP switch or trigger hotkeys from your keyboard.Port Switching via Front Panel Pushbutton18Port Switching via HotkeysHotkeys Description[Scroll Lock] [Scroll Lock] [Enter]Switch all focus (KVM, audio and USB) to the nextport[Scroll Lock] [Scroll Lock] [n] [Enter]Switch all focus (KVM, audio and USB) to port n* [Scroll Lock] [Scroll Lock] [k] [Enter]Switch KVM focus to the next port[Scroll Lock] [Scroll Lock] [n] [k] [Enter]Switch KVM focus to port n*[Scroll Lock] [Scroll Lock] [s] [Enter]Switch audio focus to the next port[Scroll Lock] [Scroll Lock] [n] [s] [Enter]Switch audio focus to port n*[Scroll Lock] [Scroll Lock] [u] [Enter]Switch USB focus to the next port[Scroll Lock] [Scroll Lock] [n] [u] [Enter]Switch USB focus to port n*Continue next page19Port Switching via Hotkeys[Scroll Lock] [Scroll Lock] [n] [k] [u] [Enter]Switch KVM and USB focus to port n*[Scroll Lock] [Scroll Lock] [n] [k] [s] [Enter]Switch KVM and audio focus to port n*[Scroll Lock] [Scroll Lock] [n] [u] [s] [Enter]Switch USB and audio focus to port n**Note: n is an interval that stands for the Port numberk stands for KVM focuss stands for audio focusu stands for USB focusPort Switching via MouseMouse Port Switching allows you to use the mouse wheel button (clicking it twice) to switch between ports. Mouse Emulation must be enabled in order for Mouse Port Switching to work. To enable mouse port switching invoke HSM and press [W] (default setting is off)20You can either activate Autoscan Mode via front panel push button or hotkeys.*Note: Autoscan Mode from front panel push button will be scanning a port every 5 seconds by default. If you wish to have the Autoscan Mode be scanning with different time interval, please refer to trigger Autoscan Mode from hotkeys.**Note: n is an interval between 1 and 99 that stands for the time (in second) desire for scanning each port.2122*Note: To exit HSM manually, press Esc or spacebar2324The PC compatible (101/104 key) keyboard can emulate the functions of the Mac keyboard. The emulation mappings are listed in the table below.*Note: When using key combinations, press and release the first key (Ctrl), then press and release thesecond key.25The PC compatible (101/104 key) keyboard can emulate the functions of the Sun keyboard. The emulationmappings are listed in the table below*Note: When using key combinations, press and release the first key (Ctrl), then press and release thesecond key.26The Windows-based Firmware Upgrade Utility (FWUpgrade.exe) provides a smooth, automated process for upgrading the GCS1642 / GCS1644’s firmware. The Utility comes as part of a Firmware Upgrade Package that is specific for each device. New firmware upgrade packages are posted on our website as new firmware revisions become available. Check the website regularly to find the latest packages and information relating to them: T o prepare for the firmware upgrade, do the following: 1. Go to our Internet support site and choose themodel name that relates to your device (GCS1642 / GCS1644) to get a list of available Firmware Upgrade Packages.2. Choose the Firmware Upgrade Package you wantto install (usually the most recent), and download it to the computer connected to port 1 on the GCS1642 / GCS1644.3. If you have a DCC mode installation, remove thecable connected to the DCC port, which connectsthe two GCS1642 / GCS1644 units, and set bothDCC switches to Host.4. Shut down all other computers connected to theGCS1642 / GCS1644 installation, except thecomputer connected to port 1.5. Invoke Firmware Upgrade Mode (see FirmwareUpgrade Mode, page 23). The front panel LEDs flashtogether to indicate Firmware Upgrade Mode is in effect. 27To upgrade your firmware:1. Run the downloaded Firmware Upgrade Package file– either by double clicking the file icon, or by openinga command line and entering the full path to it.The Firmware Upgrade Utility Welcome screen appears:2. Read the License Agreement (enable the I Agreeradio button).3. Click Next to continue. The Firmware UpgradeUtility main screen appears:284. As you select a device in the list, its descriptionappears in the Device Description panel.The Utility inspects your installation. All the devicescapable of being upgraded by the package are listedin the Device List panel.29The firmware [Ver 1.0.] is not newer than the current firmware [Ver 1.0.090] in device GCS1644 [MAIN]: 000Continue the upgrade? [Yes/No]5. After you have made your device selection(s), Click Next to perform the upgrade.If you enabled Check Firmware Version, the Utility compares the device’s firmware level with that of the upgrade files. If it finds that the device’s version is higher than the upgrade version, it brings up a dialog box informing you of the situation and gives you the option to Continue or Cancel.If you didn’t enable Check Firmware Version, the Utility installs the upgrade files without checking whether they are a higher level, or not.As the Upgrade proceeds, status messages appear in the Status Messages panel, and the progress toward completion is shown on the Progress bar.30After the upgrade has completed, a screen appears to inform you that the procedure was successful: After the upgrade has completed, a screen appears to inform you that the procedure was successful: Click Finish to close the Firmware Upgrade Utility.After a successful completion, the switches exit Firmware Upgrade Mode, and reset themselves.If you have a DCC mode installation be sure to reconnect the cable connected to the DCC port, and set the DCC switch back to Client on the appropriate switch (See Quad-View (DCC Mode), page 15).31If the Upgrade Succeeded screen doesn’t appear, it means that the upgrade failed to complete successfully, in which case you should do the following:1. Power off the GCS1642 / GCS1644 by removing the power jack.2. Invoke Firmware Upgrade Mode by holding down the Mode button on the front panel (see Mode button,page 6 & 8) and power on the GCS1642 / GCS1644. The orange LEDs flash together.3. Do the firmware upgrade procedure again.32This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential setting. This product generates, uses, and can radiate radio frequency energy and, if not installed and used as directed, it may cause harmful interference to radio communications. Although this product complies with the limits for a Class B digital device, there is no guarantee that interference will not occur in a particular installation.This device has been tested and found to comply with the following European Union directives: Electro-magnetic Capability (2004/108/EC), Low Voltage (2006/95/EC) and R&TTED (1999/5/EC).33Warranty InformationThis product carries a 3 Year Limited Warranty. For the terms and conditions of this warranty, please go to /support/warrantyRegister online at /registerImportant Product InformationProduct ModelSerial Number34WE’RE HERE TO HELP YOU!NEED ASSISTANCE SETTING UP THIS PRODUCT? Make sure you:1. Visit for more product information2. Visit /support for live help and product support IOGEAR******************35© 2018 IOGEAR®36。
DVI Video Splitter 2 4-Port 设备说明书
Instruction Manual DVI Video Splitter2/4-Port DVI Video Splitterwith AudioFCC Compliance StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.•Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarT . Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by , or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarT hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.Table of ContentsIntroduction (1)Packaging Contents (1)System Requirements (1)T op View - ST122DVIA (2)Rear View - ST122DVIA (2)Front View - ST124DVIA (3)Rear View - ST124DVIA (3)Installation (4)Hardware Installation (4)Driver Installation (5)Specifications (6)Technical Support (7)Warranty Information (7)IntroductionThe DVI Splitter with Audio lets you share one DVI video and audio source on two (ST122DVIA) or four (ST124DVIA) displays and also act as a signal amplifier that allows you to locate your DVI monitors up to 33ft (10m) away. A simple and convenient DVI video solution that suits virtually any application or operating environment (classroom, health care, professional A/V, control centres, retail POS environments), the DVI splitter/distribution amplifier is easy to install and supports high definition resolutions up to 1080p or 1920x1200 for computers.Packaging Contents1 x ST122DVIA/ST124DVIA video splitter••1 x Rack Mounting brackets (ST124DVIA only)1 x Power Adapter••1 x Instruction ManualSystem Requirements•DVI enabled video source•DVI enabled display devices•Analog stereo audio source with 3.5mm mini-plug interface (optional)•Analog stereo speakers with 3.5mm mini-plug interface (optional)Top View - ST122DVIARear View - ST122DVIA(input)(output 2)(output 1)3.5mm Audio3.5mm Audio3.5mm AudioconnectorPower/Input Output 1Output 2Front View - ST124DVIARear View - ST124DVIA3.5mm Audio3.5mm Audio(input)(output)Connector Output StatusLEDs Power/InputSignal LEDInstallationHardware Installation1.Make sure all devices are powered off and unplugged.2.Connect the DVI video source (i.e. computer, HDTV box, etc.) tothe Input connector on the splitter, using a standard male/male DVI cable. If using audio, also connect a 3.5mm mini-jack audio cable from the video source to the Input connector on the splitter. NOTE:3. Use of DVI-D cables is recommended as some DVI video sources may default to using an analog signal, when a DVI-I cable is used.4.Connect the DVI display device (i.e. monitor, HDTV, projector, etc.) to one of the Output connectors on the splitter, using standard male/male DVI cables. If using audio, also connect a 3.5mm mini-jack audio cable from the Output connector to the display device/ speakers.5.Repeat for each display device or port on the splitter.ST124DVIA ST122DVIAPower on the display devices first. At least one display device must 6.be connected to the splitter, before powering it on, to ensure proper operation.Connect power to the DVI splitter to power it on. The Power LED will 7.light up green.8.Power on the video source device. The Power LED should change to blue to indicate it is receiving a good input signal.Driver InstallationNo driver installation is required to use the DVI video splitter, as it is an external, hardware-only device, that will not be seen by the host system.SpecificationsTechnical SupportStarT ’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit /support and access our comprehensive selection of online tools, documentation, and downloads.Warranty InformationThis product is backed by a one year warranty.In addition, warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returnedfor repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.Limitation of LiabilityIn no event shall the liability of Ltd. and USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you. has been making “hard-to-find easy” since 1985, providing high quality solutions to a diverse IT and A/V customer base that spans many channels, including government, education and industrial facilities to name just a few. We offer an unmatched selection of computer parts, cables, A/V products, KVM and Server Management solutions, serving a worldwide market through our locations in the United States, Canada, the United Kingdom and T aiwan.Visit today for complete information about all our products and to access exclusive interactive tools such as the Cable Finder, Parts Finder and the KVM Reference Guide.。
DVI分配器用户手册英文版
User ManualDVI Splitter D-DV18Rev1.0.1NS110100235XI'A NNO VAS TA R TEC HC O .,L T D .StatementDear users:Welcome to use NovaPluto software. This manual is intended to help you to understand and use the product. For accuracy and reliability, this manual may be revised or modified any time without notification. Any problem in using this manual or any good suggestion, please contact us through ways provided in the manual. We will try our best to solve the problems and evaluate and adopt the suggestions as soon as possible. Thank you very much!CopyrightAll the intellectual property rights of this manual are owned by Xi’an NovaStar Tech Co., Ltd. No part of this publication may be reproduced or extracted by any means without the prior written permission of the company.Trademarkis the registered trademark of NovaStar.X I 'A NN OV AS TA RT EC HC O.,LT D.FCC Caution:Any Changes or modifications not expressly approved by the party responsible for compliance could voidthe user's authority to operate the equipment.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.X I 'A NN OV AS TA RT EC HC O.,LT D.Table of Contents1 Security Statement ............................................................................................................................2 2 Overview .............................................................................................................................................3 3Appearance ........................................................................................................................................ 4 3.1 Front panel .............................................................................................................................. 4 3.2 Back panel . (4)4 Signal Connection ............................................................................................................................. 65 Operation Instructions ......................................................................................................................6 6 Main Interface ....................................................................................................................................7 7Menu Operations .............................................................................................................................. 8 7.1 Step 1 Input Setting ............................................................................................................... 8 7.2Step 2 Factory reset (9)8 Menu Language ................................................................................................................................. 9 9 Firmware Upgrade ........................................................................................................................... 10 10 Common Problems ..................................................................................................................... 12 11 Specifications . (13)12Installation Dimensions (14)XI'A NNO VAS TA R TEC HC O .,L T D .1Security StatementPlease use this device according to the rules to prevent potential danger. In case of damage, please contact the after-sales of the company in time without randomly opening the device for repairing.High Voltage Danger: Operating voltage of the product ranges from100V to 240V AC.Grounding:wire of the power supply. Please ensure the good grounding of thegrounding conductor.Electromagnetic Interference: The device shall be far from the magnet,motor and transformer.Moistureenvironment.immersing.Away from flammable and explosive hazardous substance.Forbidinterior to avoid security accidents.X I 'A NN OV A.2OverviewD-DV18 is a DVI splitter featuring simultaneous display input and output by 1-way input and 8-way simultaneous output with the highest input resolution of 1920×1200@60Hz , supporting presetting, customization and autonomic learning by powerful DEID management function, having simple and easy-to-use LCD operating interface, and using industrial shell to fit complicated operating environment.Features:1-way input interface and 8-way output interfaces;Support up to 1920×1200@60Hz input resolution, and support HDCP;Powerful DEID management function supports presetting, customization and autonomic learning;Support Both Chinese and English;Configure LCD display and shortcut key for easy-to-use;USB control interface supports on-line program upgrade.X I 'A NN OV AS TA RT EC HC O.,LT D.3 Appearance3.1 F ront panel3.2 B ack panelNote: For improving user experience, interface layout may be adjusted slightly. Specific please in kind prevail.XI'A NN O VAS TA .X I 'A NN OV AS TA RT EC HC O.,LT D.4 Signal ConnectionRefer to the hardware device set forth in interface instruction connection in previous chapters. (Note: Please turn off the power in the process of signal connecting.)Fig. 4-1 Signal connecting diagram5 Operation InstructionsKnob:✧ Press the button to enter the manual operation interface in the main interface; ✧ Swift the knob to select menu, and press the knob to select the current menu or enterthe sub-menu;✧ Swift the knob to adjust parameters after the menu with parameters is selected. PayX I'A NN O VAS TA RT E CH CO.,L T D .attention that the knob is required to be pressed one more time for confirmation afterthe adjustment.ESC: Specifies the return key used to cancel the current menu or operation.6Main InterfaceThe main interface displayed on LCD screen is as shown in the following figure after the controller is enabled:Fig. 6-1 Main interfaceInput source status: It is as shown inpicturecase of disconnection, while it is as shownin pictureconnection.Output source status: The interfacedisplays asand not asCurrently-set EDIDX I'A NN OV AS TA RHC O.,LT D.7 Menu OperationsTip:DVI splitter D-DV18 is easy to use with a knob and a return key ESC completing many operations. Required output resolution format can be available by choosing Input Setting , Select Preset Resolution , OK .See following chapters for detailed operations.7.1 S tep 1 Input SettingUsers can set the input source resolution as required, and can set the input resolution directly on DVI splitter D-DV18.Following three setting modes are available to the input resolution: Mode 1: Preset resolution settingsSelect a proper resolution and refresh rate among the preset standard resolutions by the controller. If no proper one is available, select Mode 2 to customize the resolution.Mode 2: Customize resolution settingsSwift the knob to set the customized width, height, and refresh rate, select “Apply ”, and press the knob to confirm and apply. If it cannot be applied, the customized resolution is invalid.XI'A NN O VAS TA RT E CH CO.,L T D .Mode 3: Autonomic learningAutomatically read EDID information of the back-end device, verify and set the information as its own EDID.7.2S tep 2 Factory resetRestore the DVI splitter D-DV18 to Factory Reset.8Menu Language This device supports English.X I 'A NN OV AS TA RT EC HC O.,LT D.9 Firmware UpgradeDVI splitter D-DV18 connects to the computer on which NovaLCT-Mars is run. Log in as the advanced user with the password of “admin ” and then enter “admin ” in the main interface to make the program loading page pop up.Fig. 9-1 Advanced user interfaceXI'A NN O VAS TA RT E CH CO.,L T D .Enter “666888” in the interface as shown in Figure 9-1 to enter the program loading interface.CurrentOperation Communication Port: indicates the serial port of which the hardwareprogram is to be upgraded.Program Path: to select the currently to be upgraded hardware program. Sending Card MCU: Tick to update the sending card MCU program. Update: Modify the hardware program to the hardware device.Refresh: Refresh to display hardware version information to confirm whether the hardware program is updated correctly.XI'A NN O VAS TA RT E CH CO.,L T D .10Common ProblemsPlease perform a preliminary troubleshooting based on above steps. In case of unsolvable problems, contact the local agency or the custom service of the company in time.For safety, do not repair the processor randomly for there are high-voltage components set within the device.X I 'A NN OV AS TA RT EC HC O.,11Specifications.12Installation DimensionsFig. 12-1 D-DV18 Dimension drawing (Unit: mm)X I 'A NN OV AS TA RT EC HC O.,LT D.。
HD Electric Company 数字电压指示器 DVI-100 说明书
®TEST, MEASUREMENT & SAFETYV oltage IndicatorsDESCRIPTIONThe Digital V oltage Indicator (DVI-100) is a single point instrument designed to read the voltage on a conductor up to 99kV line-to-ground. The large LED readout is easy-to-read on the end of a long hotstick and can be used on overhead lines or in underground applications with an underground bushing probe.There are two versions of the DVI. The DVI-100indicates voltage by directly contacting conductors on overhead and underground systems. The DVI-100T with Test Point Mode also indicates voltage on elbow test points.Digital Voltage Indicators can distinguish between lines energized at full line voltage and those lines influenced from backfeed or induced voltages. DVI can also be used on distribution transformers to read both primary and secondary voltages.When brought into direct contact with a conductor while mounted on a hotstick, the two-digit display indicates the line-to-ground voltage. The instrument is auto-ranging and indicates voltages from 0.1kV - 9.9kV and from 10kV - 99kV . This allows the user to read the voltage and also determine if it is at nominal voltage or a lower induced voltage.The unit emits an audible alarm when voltage above 100V AC is detected. It is very easy-to-use as there are no range selector switches or settings to be made – just contact the conductor and read the display. To switch to Test Point Mode on the DVI-100T, simply press the ON button again and a flashing decimal appears on the display.An underground probe is required for measuring Elbow Test Points, underground or pad mount applications, or for any applications up to 21kV line-to-ground where the DVI will be used in close proximity to grounded conductors or surfaces.FEATURES•For use on system voltages up to 161kV (reads up to 99kV line-to-ground)•Large auto-ranging LED displayindicates the line-to-ground voltage level •Audible indication when voltage is detected •Voltage readout allows user to distinguish between nominal and induced voltage•Measure Elbow Test Points with the DVI-100T (underground probe required)•Use on overhead lines or in underground applications with bushing probe •Built-in universal spline for standard hotstick attachment •LED’s operate in extreme temperatures •Easy-to-read in bright or dark conditions •Built-in self-test to verify proper operation •Auto-shutoff with low battery function•Powered by a field-replaceable 9V alkaline battery •No range selector switch or settings required•Compact, rugged and lightweight polycarbonate housing •Kits are available, contact factory for detailsDigital Voltage IndicatorsDVI-100IEP-DVI-5 - Required for Underground ApplicationsPT -DVI AccessoryDVI-100 with Carrying CaseB-30AccessoryACCESSORIES•Underground Bushing Probe - IEP-DVI-5•Voltage Indicator Tester - PT-DVI •Adapter for Shotgun Stick - HSA-2500•Carrying Bag - B-30•Carrying Case - CS-DVI•Overhead Hook Probe - HP-DVI-2SPECIFICATIONSModel Numbers:DVI-100 or DVI-100TOperating Voltage Range:0 - 99kV line-to-ground(0.1kV - 9.9kV and 10kV - 99kV)Operating Frequency:60Hz (50Hz available)Operating Temperature Range:-40°F to +120°F (-40°C to +49°C)Dimensions: Housing:4.25”H x 7”W x 4.5”D(11cm x 18cm x 11cm)Overhead Probe: 8” long (20cm)Weight:1.37 lb. with small overhead probe (0.62kg)LED Height:2.25” (6cm)Accuracy:Typical overhead line accuracy in compactoverhead three phase configuration +/- 10%other applications up to +/- 25%Power Supply:Field replaceable 9-volt alkaline battery Battery Life:About 100 readings with 9V alkaline battery Standard Overhead Probe:(for overhead use only)HP-DVI-2Carrying Case:CS-DVI Rugged Plastic Carrying Case Optional Underground Probe:IEP-DVI-5 for 15, 25 and 35kV ClassDVI-100 SERIESORDERING INFORMATIONDVI-100Indicates Voltage up to 99kV. Includes (1) HP-DVI-2 & CS-DVI CaseDVI-100T/K01Indicates Voltage up to 99 kV with Capacitive Test Point Mode,Kit Includes DVI-100T, (1) HP-DVI-2, (1) IEP-DVI-5 & CS-DVI Case DVI-100T/K02Kit Includes DVI-100T, (1) HP-DVI-2, (1) IEP-DVI-5, (1) PT-DVIand CS-DVI CaseDVI-100/K01Kit Includes DVI-100, (1) HP-DVI-2, (1) IEP-DVI-5 and CS-DVI Case DVI-100/K02Kit Includes DVI-100, (1) HP-DVI-2, (1) IEP-DVI-5, (1) PT-DVIand CS-DVI CasePT-DVI Proof Tester for Digital Voltage IndicatorsIEP-DVI-5Underground Bushing Probe 15, 25 and 35 kV Class HP-DVI-2Overhead Hook Probe, 2” Diamater Opening CS-DVI Rugged Plastic Case for DVI-100 UnitsB-30Carrying bag with Fluorescent/Reflective Safety Stripes and Carrying StrapHSA-2500Universal Hotstick Adapter (Shotgun)S-4H 4' Fixed Length Fiberglass Hotstick S-6H6' Fixed Length Fiberglass Hotstick*All DVI require the use of a hotstick• Other kits are available, contact factory for details.All sales are subject to the terms and conditions of the Limitation of Warranty and Liability set forth in the product Instruction Manual and at ers must read and agree to the Limitation terms, as stated, before using the product.HD Electric Company is committed to ongoing review and improvement of its product lines,and thus reserves the right to modify product design and specifications without notice.HD Electric Company products are available through HD sales representatives worldwide.Printed in U.S.A. © HD Electric Company 2010 • Bulletin No. DVI300a。
Gefen 2x2 DVI Switcher 用户指南说明书
ASKING FOR ASSISTANCETechnical Support:Telephone (818)772-9100(800)545-6900772-9120Fax(818)Technical Support Hours:8:00 AM to 5:00 PM Monday through Friday.Write To:Gefen Inc.C/O Customer Service20600 Nordhoff StChatsworth, CA 91311*****************NoticeGefen Inc. reserves the right to make changes in the hard w are, packaging and any accompanying doc u m en t a t ion without prior written notice.The 2x2 DVI Switcher is a trademark of Gefen Inc.© 2007 Gefen Inc., All Rights ReservedTABLE OF CONTENTSIntroductionFront Panel Descriptions Back Panel DescriptionsHow To Connect The 2x2 DVI Switcher System Speci fi cations Warranty123456INTRODUCTIONThank you for purchasing Gefen’ s 2x2 DVI Switcher series. The 2x2 DVI Switcher switches DVI, USB 2.0 and Audio between any combination of two computers.Now you can switch easily and reliably between any combination of two computers using two DVI displays, USB keyboard and mouse.The 2x2 DVI Switcher saves space – there’s no need to work on a desk crowded with four monitors, keyboards and mouse devices. It saves time – there’s no need to move from one monitor to another to access different computers. And it saves money – there’s no need to purchase additional monitors, mouse devices, keyboards etc.The 2x2 DVI Switcher allows you to choose between any combination of Macintosh or PC computers and switching two monitors side by side.CONTENTSThe 2x2 DVI Switcher system consists of:(1) 2x2 DVI Switcher(1) 5V DC power supply(4) DVI to DVI cables (6FT)(2) USB cables (6FT)(2) Audio cables (6FT)(1) User Manual1-2 I n d i c a t o r L E D P o w e r L E D1-2 S w i t c h B u t t o n sP O W E R I N P U TD V I I N 1.1D V I I N 1.2D V I I N 2.1D V I I N 2.2D V I O U T 2U S B O U TU S B I N P U T SR E M O T E - R J -45 C o n n e c t e r F o r R M T -4 W i r e d R e m o t eA U D I O I N 1A U D I O I N 2A U D I O O U TD V I O U T1HOW TO CONNECT THE 2x2 DVI SWITCHER1- Connect the cables from your fi rst computer into the DVI 1.1, DVI 1.2, USB andAudio connection in the back of the 2x2 DVI Switcher.2- Connect the cable from your second computer into the DVI 2.1, DVI 2.2, USB and Audio connection in the back of the 2x2 DVI Switcher.3- Connect the monitors to the DVI Out (1 and 2) connections.4- Plug the 5v power supply into the 2x2 DVI Switcher.5- Plug the 5v wallmount power supply into the wall outlet.6- Start your computers only after you’ve made all the connections.7- Press select, to switch between Computer 1 or Computer 2 or switch remotely using the optional contact closure remote control.SPECIFICATIONSVideo Amplifi er Bandwidth ................................................................................. 1.65 GHz Input Video Signal ......................................................................................... 1.2 volts p-p Input Sync Signal ................................................................................... 5 volts p-p (TTL) Single Link Range ......................................................................................... 1920 x 1200 Vertical Frequency Range ....................................................................................... 60 Hz DVI Input/Output Connector Type ............................................................................. DVI-I USB Version ........................................................................................................ USB 2.0 USB Input Connector .......................................................................................... Type “B” USB Output Connector ........................................................................................ Type “A” Power Consumption ................................................................................ 18 Watts (max.) Power Supply ......................................................................................................... 5V DC Dimensions ...................................................................................... 16”W x 1.75”H x 4”D Rackmountable ........................................................................................... 1 Rack Space Shipping Weight ..................................................................................................... 12 LbsWARRANTYGefen Inc. warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects and Gefen Inc. is notifi ed within two (2) year from the date of shipment, Gefen Inc. will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifi cations.Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for ninety (90) days from the day of reshipment to the Buyer.This warranty is in lieu of all other warranties expressed or implied, including without limitation, any implied warranty or merchantability or fi tness for any particular purpose, all of which are expressly disclaimed.1. Proof of sale may be required in order to claim warranty.2. Customers outside the US are responsible for shipping charges to and from Gefen.3. Copper cables are limited to a 30 day warranty and cable must be free from anyscratches, markings, and neatly coiled.The information in this manual has been carefully checked and is believed to be accurate. However, Gefen Inc. assumes no responsibility for any inaccuracies that may be contained in this manual. In no event will Gefen Inc., be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. The technical information contained herein regarding the 2x2 DVI Switcher features and specifi cations is subject to change without notice.。
Mini DisplayPort to DVI Adapter 用户手册说明书
PSG90909PSG90910User ManualTable of Contents1.0 Introduction (1)2.0 Specifications (1)3.0 Package Contents (2)4.0 Panel Descriptions (2)5.0 Connection and Operation (2)Mini DisplayPort to DVI AdapterMini DisplayPort to DVI AdapterDEAR CUSTOMERThank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.1.0 INTRODUCTIONThe Mini DisplayPort to DVI Adapter seamlessly connect next generation DisplayPort based MacBook, MacBook Pro, or MacBook Air with a Mini DisplayPort to conventional DVI displays, such as CRT, LCD monitors and projectors. Mini DisplayPort offers a unified, scalable, and cost effective interface for embedded and external display applications. It not only has an elegant appearance with the white color but also brings much convenience with its small size.It offers solutions for digital entertainment center, projector factory, noisy space and security concerns, conference room presentation, school and corporate training environments.1.1FEATURES●Support Mini DisplayPort 1.1 input and DVI output.●Support DVI highest video resolution 1080p.●Support DVI 225MHz/2.25Gbps per channel (6.75Gbps all channel)bandwidth.●Support DVI 12bit per channel (36bit all channel) deep color.●Powered from Mini DisplayPort source.2.0 SPECIFICATIONSSignal Inputs/OutputInput Video Signal 5 Volts p-p (TTL)Maximum Single Link Range 1920x1080POutput Video DVIInput/Output Connector Input: Mini DisplayPort Male 20pinOutput: DVI Female (24+5)Operating FrequencyVertical Frequency Range50/60HzVideo Amplifier Bandwidth 2.25Gbps/225MHzResolutions(HDTV)Interlaced(50&60Hz) 480i,576i,1080iProgressive(50&60Hz) 480p,576p,720p,1080pWarrantyLimited Warranty 1 Year Parts and Labor EnvironmentalMini DisplayPort to DVI Adapter Operating Temperature 0 ℃to +70℃Operating Humidity 10% to 85 % RH (no condensation) Storage Temperature -10℃to +80℃Storage Humidity 5% to 90 % RH (no condensation) Power RequirementExternal Power Supply No external power neededPower consumption (Max) 3WRegulatory ApprovalsConverter Unit FCC,CE,ULPower Supply UL,CE,FCCAccessories AdapterUser ManualNote: Specifications are subject to change without notice.3.0 Package ContentsBefore attempting to use this unit, please check the packaging and make sure the following items are contained in the shipping carton:●Main unit●User's Manual4.0 PANEL DESCRIPTIONS5.0 CONNECTION AND OPERATION1) Connect the Mini DisplayPort male to Mini DisplayPort source device.2) Connect the DVI female to display by DVI M/M cable.Attention: Insert / Extract cable gently.5.1 CONNECTION DIAGRAMMini DisplayPort to DVI AdapterP/N:C016PSG90909PSG90910。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
T/RDVI-4S
HD DVI optical transceiver specification Product Overview
T/RDVI-4S optical transceiver is a kind of DVI remote transmission product in order to DVI the problem of digit transmission and develop . Meanwhile , optical fiber transmission owns some advantages : small attenuation , wide bandwidth,
strong anti-jamming, high safety performance ,small volume, light weight ,etc. ,
so it has incomparable advantages in long distance transmission and special
Environment ,etc.
T/RDVI-4S optical transceiver transmit the high definition DVI signal of the computers via four cores single-mode or multi-mode optical fiber , up to 10 km . It can be widely used in professional A/V, large conference system, large exhibition venues, aerospace command and control center, digital cinema and TV wall, army command system, stadiums and display system, the financial securities trading places, medical institutions, security system, campus environment, industrial control and so on, in order to meet the needs from remote access computers or the video signal
Product Features
Using special ASIC, high-speed DSP, and the surface mount, and other advanced technology; No radiation electromagnetic interference, good privacy;
Provide complete electrical isolation, avoid sending and receiving equipment mutual interference; Use the standard DVI-D, DVI-I interface;
Support the highest computer resolution UXGA1600x1200;
Support all the existing display standards;
Industrial design, high reliability;
Easy installation, when using, without regulation;
Packing list
User Manual
maintena
nce card
Qualified
Certification
Power Adapter Facility
1 copy 1 copy 1 copy 1 piece 1 set
Built-in precision component, please note that handled with care to avoid severe vibration, lest affect equipment performance. If equipment is damaged in transit or lost any parts, please inform our company or our distributor in time , we solve properly for you as soon as possible
Input/output resolution:
Display Mode Resolution
Refresh Frequency
VGA 640x480 60、70、75、85 Hz SVGA 800x600 60
、70、75
、85 Hz XGA 1024x768 60、70、75、85 Hz SXGA 1280x1024 60、70、75 Hz
1366x768 60 Hz 1400x1050 60 Hz 1920x1080 60 Hz UXGA
1600x1200
60 Hz
Work Environment
Operating Temperature::-30
℃～+ 70℃
Relative humidity :0～95%(Non-condensing)
Protection grade :General industry standard or special specified
Power supply mode: voltage AC/DC 220 V / 110 V + 5 V power supply
Product Size :
Stand alone type ;L * W * H ：116mm*110mm*25mm
Transmitter Panel Instruction
DVI IN DVI signal input, need connect the computer with DVI port
F1 F2 F3 F4
Fiber input port
P
If the led is On , the power connects normally
Receiver Panel Instruction
DVI OUT DVI signal output , need connect the display with DVI port
F1 F2 F3 F4
Fiber input port
P If the led is On , the power connects normally
1 2 3 4
When the fiber port of transmitter & receiver turn on , the led will be on
Production Application Map :
When using the DVI device , the device need be with DVI port or the device need be transferred with transfer cable to convert。