注塑常用术语英文表达

1.雾气Moisture Streaks
2.玻纤分配不均Glass Fiber Streaks
3.困气Gas Trap Effect
4.银丝纹Sliver Marks
5.联合线Weld Line
6.水波痕Water Wave Effect
7.黑点Dark Sport
8.顶出印Visible Ejector Marks
9.变形Deformation During Demolding
10.填补不足Short Filling
11.冷料流痕Cold Slug
12.进胶口点不良Dull Spots Near The Sprue
13.发射痕Jetting
14.表面起层Flaking Of The Surface Layer
15.浮泡Entrapped Air
16.过热变色Burnt Streaks
17.龟裂Stress Crack
18.缩水痕Sink Marks
19.真空气泡Density Bubble
20.披锋Flash
21.擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface
22 尺寸过大Over dimension
23 尺寸过小Under dimension
24 翘曲Warpage/warped
25 缩短Shrinkage/shrink
26 缩影Sink marks
27 打不满Short shot/short molding
塑料模具mould of plastics
注塑模具injection mould
冲压模具die
模架 mould base
定模座板 Top clamping plate
Top plate
Fixed clamp plate
水口推板stripper plate
A 板 A plate
B 板 B plate
支承板support plate
方铁spacer plate
底针板ejector plate
面针板ejector retainer plate
回针Return pin
导柱Guide pin
有托导套Shoulder Guide bush
直导套Straight Guide bush
动模座板 Bottom clamp plate Moving clamp plate
基准线 datum line
基准面 datum plan
型芯固定板core-retainer plate
凸模固定板punch-retainer plate
顶针 ejector pin
单腔模具single cavity mould
多腔模具multi-cavity mould
多浇口 multi-gating
浇口 gate
缺料 starving
排气 breathing
光彩 gloss
合模力 mould clamping force
锁模力 mould locking force
挤出 extrusion
开裂 crack
循环时间cycle time
老化 aging
螺杆 screw
麻点 pit
嵌件 insert
活动镶件movable insert
起垩 chalking
浇注系统feed system
主流道sprue
分流道 runner
浇口 gate
直浇口 direct gate , sprue gate
轮辐浇口spoke gate , spider gate
点浇口 pin-point gate
测浇口 edge gate
暗藏浇口submarine gate , tunnel gate 料穴 cold-slug well
浇口套 sprue bush
流道板 runner plate
排飞槽 vent
分型线（面） parting line
定模 stationary mould ， Fixed mould 动模 movable mould, movable half
上模 upper mould ， upper half
下模 lower mould ， lower half
型腔 cavity
凹模 cavity plate ， cavity block
拼块 split
定位销 dowel
定位销孔dowel hole
型芯 core
斜销 angle pin, finger cam
滑块 slide
滑块导板slide guide strip
楔紧块 heel block, wedge lock
拉料杆 sprue puller
定位环 locating ring
冷却通 cooling channel
脱模斜度draft
滑动型芯slide core
螺纹型芯threaded core
热流道模具hot-runner mould
绝热流道模insulated runner mould
熔合纹 weld line（flow line）
三板式模具three plate mould
脱模 ejection
换模腔模具interchangeable cavity mould 脱模剂 release agent
注射能力shot capacity
注射速率injection rate
注射压力injection pressure
差色剂 colorant
保压时间holdup time
闭模时间closing time
定型装置sizing system
阴模 female mould ， cavity block
阳模 male mould
电加工设备Electron Discharge Machining
数控加工中心CNC machine center
全能铁床 Universal milling machine
卧式刨床 Horizontal planer
车床 Engine lathe
平面磨床Surface grinding machine
去磁机 Demagnetization machine
全能摇臂钻床Universal radial movable driller 立式钻床 Vertical driller
超声波冲刷机Ultrasonic clearing machine。