1850851中文资料
PCA8565TS1,118;PCA8565BS1,118;中文规格书,Datasheet资料
1.General descriptionThe PCA8565 is a CMOS 1 real time clock and calendar optimized for low powerconsumption.A programmable clock output,interrupt output and voltage-low detector are also provided. All address and data are transferred serially via a two-line bidirectional I 2C-bus. Maximum bus speed is 400kbit/s. The built-in word address register is incremented automatically after each written or read data byte.AEC-Q100 compliant (PCA8565TS) for automotive applications.2.FeaturesI Provides year, month, day, weekday, hours, minutes and seconds based on a 32.768kHz quartz crystal I Century flagI Clock operating voltage: 1.8V to 5.5VI Extended operating temperature range:−40°C to +125°CI Low backup current; typical 0.65µA at V DD =3.0V and T amb =25°C I 400kHz two-wire I 2C-bus interface (at V DD =1.8V to 5.5V)I Programmable clock output for peripheral devices (32.768kHz,1.024kHz,32Hz and 1Hz)I Alarm and timer functions I Internal power-on resetI I 2C-bus slave address: read A3h and write A2h I Open-drain interrupt pinI One integrated oscillator capacitor3.ApplicationsI Automotive I IndustrialI Other applications that require a wide operating temperature rangePCA8565Real time clock/calendarRev. 02 — 16 June 2009Product data sheet1.The definition of the abbreviations and acronyms used in this data sheet can be found in Section 16.4.Ordering information5.Marking Table 1.Ordering informationType number PackageName Description Version PCA8565TS TSSOP8plastic thin shrink small outline package; 8 leads;body width 3 mmSOT505-1PCA8565BS HVSON10plastic thermal enhanced very thin small outlinepackage; no leads; 10 terminals;body 3×3× 0.85mmSOT650-1Table 2.Marking codesType number Marking codePCA8565TS8565PCA8565BS8565S6.Block diagramFig 1.Block diagram of PCA8565001aah661PCA8565OSCILLATOR 32.768 kHzDIVIDERCLOCK OUTINTERRUPTCLKOUTMONITORPOWER-ON RESETWATCH DOGI 2CINTERFACEOSCISCLSDA OSCOV DD V SSTIMER FUNCTIONTimer_control 0Eh Timer0FhCONTROL Control_100h Control_201h CLKOUT_control0DhTIMESeconds 02h Minutes 03hHours 04h Days 05h ALARM FUNCTIONMinute_alarm 09h Hour_alarm 0AhDay_alarm 0Bh Weekday_alarm0ChWeekdays 06h Months_century 07hYears 08hINT7.Pinning information7.1Pinning7.2Pin description[1]The die paddle (exposed pad) is wired to V SS but should not be electrically connected.Top view. For mechanical details see Figure 28.For mechanical details see Figure 29.Fig 2.Pin configuration of PCA8565TS (TSSOP8)Fig 3.Pin configuration of PCA8565BS (HVSON10)PCA8565TSOSCI V DD OSCO CLKOUT INT SCL V SSSDA001aaj75412346587001aaj753PCA8565BS SDAINT V SSSCL n.c.CLKOUT OSCO V DD OSCI n.c.Transparent top view56473829110terminal 1index areaTable 3.Pin descriptionSymbol Pin DescriptionTSSOP8HVSON10OSCI 11oscillator input OSCO 22oscillator outputn.c.-3, 10do not connect and do not use as feed through;connect to V DD if floating pins are not allowed INT 34interrupt output (open-drain; active LOW)V SS 45[1]ground SDA 56serial data I/O SCL 67serial clock input CLKOUT 78clock output, open-drain V DD89positive supply voltage8.Device protection diagram9.Functional descriptionThe PCA8565contains sixteen 8-bit registers with an auto-incrementing address register,an on-chip 32.768kHz oscillator with one integrated capacitor, a frequency divider which provides the source clock for the Real Time Clock (RTC),a programmable clock output,a timer, an alarm, a voltage-low detector and a 400kHz I 2C-bus interface.All 16registers are designed as addressable 8-bit registers although not all bits are implemented:•The first two registers (memory address 00h and 01h)are used as control and statusregisters•The registers at memory addresses 02h through 08h are used as counters for theclock function (seconds up to years counters)•Address locations 09h through 0Ch contain alarm registers which define theconditions for an alarm•The register at address 0Dh controls the CLKOUT output frequency•At address 0Eh is the timer control register and address 0Fh contains the timer valueThe arrays SECONDS, MINUTES, HOURS, DAYS, WEEKDAYS, MONTHS, YEARS as well as the bit fields MINUTE_ALARM, HOUR_ALARM, DAY_ALARM and WEEKDAY_ALARM are all coded in Binary Coded Decimal (BCD) format.When one of the RTC registers is read the contents of all time counters are frozen. This prevents faulty reading of the clock or calendar during a carry condition (see Section 10.5.3).Fig 4.Device diode protection diagram of PCA8565mce169SDAV SS SCLINTCLKOUTOSCO V DDOSCIPCA85659.1Register overviewTable 4.Register overview and control bits default valuesBit positions labeled as- are not implemented. Bit positions labeled as N should always be written with logic0. Reset values are shown in Table7.Address Register name Bit76543210 Control registers00h Control_1TEST1N STOP N TESTC N N N01h Control_2N N N TI_TP AF TF AIE TIE Time and date registers02h Seconds VL SECONDS (0 to 59)03h Minutes-MINUTES (0 to 59)04h Hours--HOURS (0 to 23)05h Days--DAYS (1 to 31)06h Weekdays-----WEEKDAYS (0 to 6)07h Months_century C--MONTHS (1 to 12)08h Y ears YEARS (0 to 99)Alarm registers09h Minute_alarm AE_M MINUTE_ALARM (0 to 59)0Ah Hour_alarm AE_H-HOUR_ALARM (0 to 23)0Bh Day_alarm AE_D-DAY_ALARM (1 to 31)0Ch Weekday_alarm AE_W----WEEKDAY_ALARM (0 to 6) CLKOUT control register0Dh CLKOUT_control FE-----FDTimer registers0Eh Timer_control TE-----TD0Fh Timer COUNTDOWN_TIMER9.2Control registers9.2.1Register Control_1Table 5.Register Control_1 (address00h) bits descriptionBit Symbol Value Description7TEST10[1]normal mode1EXT_CLK test mode6N0[2]default value5STOP0[1]RTC source clock runs1all RTC divider chainflip-flops are asynchronously set tologic0;the RTC clock is stopped(CLKOUT at32.768kHz is stillavailable)4N0[2]default value3TESTC0power-on reset override facility is disabled;set to logic0 for normal operation1[1]power-on reset override may be enabled2to0N000[2]default value[1]Default value.[2]Bits labeled as N should always be written with logic 0.9.2.2Register Control_2Table 6.Register Control_2 (address01h) bits descriptionBit Symbol Value Description7to5N000[1]default value4TI_TP0[2]INT is active when TF is active (subject to the status ofTIE)1INT pulses active according to T able26 (subject to thestatus of TIE);Remark:note that if AF and AIE are active then INT willbe permanently active3AF0[2]alarm flag inactive1alarm flag active2TF0[2]timer flag inactive1timer flag active1AIE0[2]alarm interrupt disabled1alarm interrupt enabled0TIE0[2]timer interrupt disabled1timer interrupt enabled[1]Bits labeled as N should always be written with logic 0.[2]Default value.9.3ResetThe PCA8565 includes an internal reset circuit which is active whenever the oscillator is stopped.In the reset state the I2C-bus logic is initialized including the address pointer.All other registers are set according to Table7.Table 7.Register reset values[1]Address Register name Bit76543210 00h Control_10000100001h Control_2x x00000002h Seconds1x x x x x x x03h Minutes1x x x x x x x04h Hours x x x x x x x x05h Days x x x x x x x x06h Weekdays x x x x x x x x07h Months_century x x x x x x x x08h Y ears x x x x x x x x09h Minute_alarm1x x x x x x x0Ah Hour_alarm1x x x x x x x0Bh Day_alarm1x x x x x x x0Ch Weekday_alarm1x x x x x x x0Dh CLKOUT_control1x x x x x000Eh Timer_control0x x x x x110Fh Timer x x x x x x x x[1]Registers labeled ‘x’ are undefined at power-on and unchanged by subsequent resets.9.4Time and date registersThe majority of the registers are coded in the BCD format to simplify application use.Table 8.Register Seconds (address02h) bits descriptionBit Symbol Value Place value Description7VL0-clock integrity is guaranteed1[1]-integrity of the clock information is not guaranteed 6to4SECONDS0to5[2]ten’s place actual seconds coded in BCD format3 to 00 to 9[2]unit place[1]Start-up value.[2]Values shown in decimal.[1]Values shown in decimal.[1]Values shown in decimal.[1]The PCA8565 compensates for leap years by adding a 29th day to February if the year counter contains a value which is exactly divisible by 4, including the year 00.[2]Values shown in decimal.[1]Values shown in decimal.Table 9.Seconds coded in BCD formatSeconds value in decimal Upper-digit (ten’s place)Digit (unit place)Bit 6Bit 5Bit 4Bit 3Bit 2Bit 1Bit 0000000000010000001020000010:090001001100010000:581011000591111Table 10.Register Minutes (address 03h) bits descriptionBit Symbol Value Place value Description 7---unused6to 4MINUTES0to 5[1]ten’s place actual minutes coded in BCD format3 to 00 to 9[1]unit placeTable 11.Register Hours (address 04h) bits descriptionBit SymbolValue Place value Description 7 to 6---unused5to 4HOURS 0to 2[1]ten’s place actual hours coded in BCD format3 to 00 to 9[1]unit placeTable 12.Register Days (address 05h) bits descriptionBit SymbolValue Place value Description 7 to 6---unused5to 4DAYS [1]0to 3[2]ten’s place actual day coded in BCD format3 to 00 to 9[2]unit placeTable 13.Register Weekdays (address 06h) bits descriptionBit SymbolValue Description 7 to 3--unused2to 0WEEKDAYS0to 6[1]actual weekday values, see Table 14[1]Definition may be re-assigned by the user.[1]This bit may be re-assigned by the user.[2]This bit is toggled when the years register overflows from 99 to 00.[3]Values shown in decimal.Table 14.Weekday assignmentsDay [1]Bit 210Sunday 000Monday 001T uesday010Wednesday 011Thursday 100Friday 101Saturday11Table 15.Register Months_century (address 07h) bits descriptionBit SymbolValue Place value Description 7C [1]0[2]-indicates the century is x 1-indicates the century is x +16 to 5---unused4MONTHS0to 1[3]ten’s place actual month coded in BCD format, see Table 163 to 00 to 9[3]unit placeTable 16.Month assignments coded in BCD formatMonthUpper-digit (ten’s place)Digit (unit place)Bit 4Bit 3Bit 2Bit 1Bit 0January 00001February 00010March 00011April 00100May 00101June 00110July 00111August 01000September 01001October 10000November 10001December11分销商库存信息:NXPPCA8565TS/1,118PCA8565BS/1,118。
REC1.8-0505SRH1中文资料
2.54
1.0ø+0.15/0
2.54
Top View
24 PIN DIP SMD Package
32.30 10.20 2.54 8.89 9.60 14.50
Pin Connections Pin # 1 & 24 2 & 23 3 & 21 22 10 & 15 Single +Vin NC NC NC –Vout +Vout –Vin
Input Voltage Range Output Voltage Accuracy Line Voltage Regulation Load Voltage Regulation (10% to 100% full load ) Output Ripple and Noise (at 20MHz BW) Operating Frequency Efficiency No Load Power Consumption Isolation Voltage Rated Working Voltage Isolation Capacitance Isolation Resistance Short Circuit Protection Short Circuit Protection Storage Temperature Range Temperature Coefficient Relative Humidity Thermal Impedance Package Weight MTBF (+25°C) (+80°C) 62 Natural convection using MIL-HDBK 217F using MIL-HDBK 217F July-2006 -40°C to +80°C (see Graph) -50°C to +125°C ±0.02%/°C 95% RH 20°C/W for metal case 8.5g
1850673资料
Extract from the onlinecatalogFRONT-MC 1,5/ 3-ST-3,81Order No.: 1850673The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1850673Plug component, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81 mm, no. of positions: 3, type of connection: Screw connectionhttp://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsPitch 3.81 mmDimension a7.62 mmNumber of positions3Screw thread M 2Tightening torque, min0.22 NmTechnical dataInsulating material group IRated surge voltage (III/3) 2.5 kVRated surge voltage (III/2) 2.5 kVRated surge voltage (II/2) 2.5 kVRated voltage (III/2)160 VRated voltage (II/2)320 VConnection in acc. with standard EN-VDENominal current I N8 ANominal voltage U N160 VNominal cross section 1.5 mm2Maximum load current8 A (with 1.5 mm2 conductor cross section) Insulating material PAInflammability class acc. to UL 94V0Internal cylindrical gage A1Stripping length9 mmConnection dataConductor cross section solid min.0.14 mm2Conductor cross section solid max. 1.5 mm2Conductor cross section stranded min.0.14 mm2Conductor cross section stranded max. 1.5 mm2Conductor cross section stranded, with ferrule0.25 mm2without plastic sleeve min.Conductor cross section stranded, with ferrule1.5 mm2without plastic sleeve max.Conductor cross section stranded, with ferrule0.25 mm2with plastic sleeve min.Conductor cross section stranded, with ferrule0.5 mm2with plastic sleeve max.Conductor cross section AWG/kcmil min.28Conductor cross section AWG/kcmil max162 conductors with same cross section, solid min.0.14 mm22 conductors with same cross section, solid max.0.5 mm22 conductors with same cross section, stranded0.14 mm2min.2 conductors with same cross section, stranded0.75 mm2max.2 conductors with same cross section, stranded,0.25 mm2ferrules without plastic sleeve, min.2 conductors with same cross section, stranded,0.34 mm2ferrules without plastic sleeve, max.2 conductors with same cross section, stranded,0.5 mm2TWIN ferrules with plastic sleeve, min.2 conductors with same cross section, stranded,0.5 mm2TWIN ferrules with plastic sleeve, max.Certificates / ApprovalsApproval logoCSANominal voltage U N300 VNominal current I N8 AAWG/kcmil28-16CULNominal voltage U N300 VNominal current I N8 AAWG/kcmil30-16ULNominal voltage U N300 VNominal current I N8 AAWG/kcmil30-16Certification CB, CSA, CUL, UL, VDE-PZIAccessoriesItem Designation DescriptionMarking1051993B-STIFT Marker pen, for manual labeling of unprinted Zack strips,smear-proof and waterproof, line thickness 0.5 mm0804109SK 3,81/2,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 10-sectionmarker strip, 14 identical decades marked 1-10, 11-20 etc. up to91-(99)100, sufficient for 140 terminal blocks0805056SK 3,81/2,8:SO Marker card, special printing, self-adhesive, labeled acc. tocustomer requirements, 14 identical marker strips per card, max.25-position labeling per strip, color: White0803883SK U/2,8 WH:UNBEDRUCKT Unprinted marker cards, DIN A4 format, pitch as desired,self-adhesive, with 50 stamped marker strips, 185 mm strip length,can be labeled with the CMS system or manually with the M-PENTools1205037SZS 0,4X2,5Screwdriver, bladed, matches all screw terminal blocks up to 1.5mm² connection cross section, blade: 0.4 x 2.5 mmAdditional productsItem Designation DescriptionGeneral1897814EMC 1,5/ 3-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 3, mounting: Press in1860650EMCV 1,5/ 3-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 3, mounting: Press in1857896IMC 1,5/ 3-ST-3,81Plug component, nominal current: 8 A, rated voltage: 160 V, pitch:3.81 mm, no. of positions: 3, type of connection: Screw connection 1803280MC 1,5/ 3-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 3, mounting: Soldering1908774MC 1,5/ 3-G-3,81 THT Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 3, mounting: SMD/THT1829963MCD 1,5/ 3-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 3, mounting: Soldering1843088MCD 1,5/ 3-G1-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 3, mounting: Soldering1830415MCDV 1,5/ 3-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 3, mounting: Soldering1847738MCDV 1,5/ 3-G1-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 3, mounting: Soldering1861730MCO 1,5/ 3-GL-3,81Header, nominal current: 8 A, rated voltage: 125 V, pitch: 3.81mm, no. of positions: 3, mounting: Soldering1861659MCO 1,5/ 3-GR-3,81Header, nominal current: 8 A, rated voltage: 125 V, pitch: 3.81mm, no. of positions: 3, mounting: Soldering1803439MCV 1,5/ 3-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 3, mounting: Soldering1832701MCVDU 1,5/ 3-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 3, mounting: Soldering1832743MCVK 1,5/ 3-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 3, mounting: Mounting rail1827282SMC 1,5/ 3-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 3, mounting: SolderingDrawingsDimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。
1850738资料
Extract from the onlinecatalogFRONT-MC 1,5/ 9-ST-3,81Order No.: 1850738The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1850738Plug component, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81 mm, no. of positions: 9, type of connection: Screw connectionhttp://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsPitch 3.81 mmDimension a30.48 mmNumber of positions9Screw thread M 2Tightening torque, min0.22 NmTechnical dataInsulating material group IRated surge voltage (III/3) 2.5 kVRated surge voltage (III/2) 2.5 kVRated surge voltage (II/2) 2.5 kVRated voltage (III/2)160 VRated voltage (II/2)320 VConnection in acc. with standard EN-VDENominal current I N8 ANominal voltage U N160 VNominal cross section 1.5 mm2Maximum load current8 A (with 1.5 mm2 conductor cross section) Insulating material PAInflammability class acc. to UL 94V0Internal cylindrical gage A1Stripping length9 mmConnection dataConductor cross section solid min.0.14 mm2Conductor cross section solid max. 1.5 mm2Conductor cross section stranded min.0.14 mm2Conductor cross section stranded max. 1.5 mm2Conductor cross section stranded, with ferrule0.25 mm2without plastic sleeve min.Conductor cross section stranded, with ferrule1.5 mm2without plastic sleeve max.Conductor cross section stranded, with ferrule0.25 mm2with plastic sleeve min.Conductor cross section stranded, with ferrule0.5 mm2with plastic sleeve max.Conductor cross section AWG/kcmil min.28Conductor cross section AWG/kcmil max162 conductors with same cross section, solid min.0.14 mm22 conductors with same cross section, solid max.0.5 mm22 conductors with same cross section, stranded0.14 mm2min.2 conductors with same cross section, strandedmax.0.75 mm22 conductors with same cross section, stranded,ferrules without plastic sleeve, min.0.25 mm22 conductors with same cross section, stranded,ferrules without plastic sleeve, max.0.34 mm22 conductors with same cross section, stranded,TWIN ferrules with plastic sleeve, min.0.5 mm22 conductors with same cross section, stranded,TWIN ferrules with plastic sleeve, max.0.5 mm2 Certificates / ApprovalsApproval logoCSANominal voltage U N300 VNominal current I N8 AAWG/kcmil28-16CULNominal voltage U N300 VNominal current I N8 AAWG/kcmil30-16ULNominal voltage U N300 VNominal current I N8 AAWG/kcmil30-16Certification CB, CSA, CUL, UL, VDE-PZIAccessoriesItem Designation DescriptionMarking1051993B-STIFT Marker pen, for manual labeling of unprinted Zack strips, smear-proof and waterproof, line thickness 0.5 mm0804109SK 3,81/2,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 10-section markerstrip, 14 identical decades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for 140 terminal blocks0805056SK 3,81/2,8:SO Marker card, special printing, self-adhesive, labeled acc. tocustomer requirements, 14 identical marker strips per card, max.25-position labeling per strip, color: White0803883SK U/2,8 WH:UNBEDRUCKT Unprinted marker cards, DIN A4 format, pitch as desired, self-adhesive, with 50 stamped marker strips, 185 mm strip length, canbe labeled with the CMS system or manually with the M-PENTools1205037SZS 0,4X2,5Screwdriver, bladed, matches all screw terminal blocks up to 1.5mm² connection cross section, blade: 0.4 x 2.5 mmAdditional productsItem Designation DescriptionGeneral1897872EMC 1,5/ 9-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 9, mounting: Press in1860715EMCV 1,5/ 9-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 9, mounting: Press in1857951IMC 1,5/ 9-ST-3,81Plug component, nominal current: 8 A, rated voltage: 160 V, pitch:3.81 mm, no. of positions: 9, type of connection: Screw connection 1803345MC 1,5/ 9-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 9, mounting: Soldering1908839MC 1,5/ 9-G-3,81 THT Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 9, mounting: SMD/THT1830020MCD 1,5/ 9-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 9, mounting: Soldering1843143MCD 1,5/ 9-G1-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 9, mounting: Soldering1830473MCDV 1,5/ 9-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 9, mounting: Soldering1847806MCDV 1,5/ 9-G1-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 9, mounting: Soldering1861798MCO 1,5/ 9-GL-3,81Header, nominal current: 8 A, rated voltage: 125 V, pitch: 3.81mm, no. of positions: 9, mounting: Soldering1861714MCO 1,5/ 9-GR-3,81Header, nominal current: 8 A, rated voltage: 125 V, pitch: 3.81mm, no. of positions: 9, mounting: Soldering1803497MCV 1,5/ 9-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 9, mounting: Soldering1837502MCVDU 1,5/ 9-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 9, mounting: Soldering1832808MCVK 1,5/ 9-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 9, mounting: Mounting rail1827347SMC 1,5/ 9-G-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 9, mounting: SolderingDrawingsDimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。
19857;19858;19859;中文规格书,Datasheet资料
"If any part of the loop should open (become disconnected or have out of limit resistance), the circuit will go into the alarm state" [ref TR20.20], nonetheless, due to the redundancy inherent in the dual wire wrist strap design, the operator will continue to be grounded via the second intact wire. Per ESD Handbook TR20.20 section 5.3.9.2.2 Dual Conductor Resistance Continuous Monitors, "This type of monitor is used with a two wire (dual conductor) wrist strap. The wrist strap assembly consists of a two-wire ground cord and a wristband that has two isolated halves. When a person is wearing the wrist strap properly, the monitor measures the loop resistance consisting of one wire of the ground cord, one-half of the wristband, the person's skin, the second half of the wristband, and a second wire in the ground cord. If any part of the loop should open (become disconnected or have out of limit resistance), the circuit will go into the alarm state. ESD Handbook TR 20.20 paragraph 5.3.2.4.4 Test Frequency "Because wrist straps have a finite life, it is important to develop a test frequency that will guarantee integrity of the system. Typical test programs recommend that wrist straps that are used daily should be tested daily. However, if the products that are being produced are of such value that knowledge of a continuous, reliable ground is needed, and then continuous monitoring should be considered or even required" Continuous Monitors pay for themselves improving quality, productivity, eliminating wrist strap daily testing and test result logging. Per ESD-S1.1 paragraph 6.1.3 Frequency of Functional Testing "Daily [Wrist Strap] testing may be omitted if constant monitoring is used." Improve wrist strap contact with Reztore™ ESD Hand Lotion. * U.S. Patents 6,052,053 and 6,205,408 Made in America
2-862548-1中文资料
2-862548-1 Product DetailsHome | Customer Support | Suppliers | Site Map | Privacy Policy | Browser Support© 2008 Tyco Electronics Corporation All Rights Reserved SearchProducts Documentation Resources My Account Customer SupportHome > Products > By Type > High Voltage LGH Products > Product Feature Selector > Product DetailsNo Image Available2-862548-1Active LGH Single-Pin Connectors and CableAssembliesAlways EU RoHS/ELV Compliant (Statement of Compliance)Product Highlights:?Lead Assembly?15 kVDC Operating Voltage?Lead Assembly Type = Double-End?Assembly Length = 482.60 mm?Barrel Depth = 22.61 mmView all Features | Find SimilarProductsCheck Pricing &AvailabilitySearch for ToolingProduct FeatureSelectorContact Us AboutThis ProductQuick LinksDocumentation & Additional InformationProduct Drawings:?LEAD ASS'Y, POS STOP, DBLE. END, LGH-1/2L(PDF, English)Catalog Pages/Data Sheets:?None AvailableProduct Specifications:?Standard LGH Connectors, Series 1/2I, 1/2LI, 1I, 1LI...(PDF, English)Application Specifications:?None AvailableInstruction Sheets:?None AvailableCAD Files:?None AvailableList all Documents Additional Information:?Product Line InformationRelated Products:?ToolingProduct Features (Please use the Product Drawing for all design activity)Product Type Features:?Product Type = Lead Assembly?Mount Angle = Straight?Cap Material = Glass-Filled Polyester?Shielded = No?Wire Size (mm²[AWG]) = 16Electrical Characteristics:?Operating Voltage (kVDC) = 15Body Related Features:?Lead Assembly Type = Double-End?Assembly Length (mm [in]) = 482.60 [19.000] ?Barrel Depth (mm [in]) = 22.61 [0.890]?Positive Stop Ferrule = With?Wire Color = White (Standard)?Cap Color = Green?Wire Diameter (mm [in]) = 4.22 [0.166]?Wire Insulation = Silicone Industry Standards:?RoHS/ELV Compliance = RoHS compliant, ELVcompliant?Lead Free Solder Processes = Not relevant forlead free process?RoHS/ELV Compliance History = Always wasRoHS compliantOther:?Brand = AMPProvide Website Feedback | Contact Customer Support。
1850576资料
Extract from the onlinecatalogSMSTB 2,5/18-ST-5,08Order No.: 1850576The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1850576Plug component, nominal current: 12 A, rated voltage: 250 V, pitch: 5.08 mm, no. of positions: 18, type of connection: Screw connectionhttp://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsHeight15.5 mmPitch 5.08 mmDimension a86.36 mmNumber of positions18Screw thread M 3Tightening torque, min0.5 NmTechnical dataInsulating material group IRated surge voltage (III/3) 4 kVRated surge voltage (III/2) 4 kVRated surge voltage (II/2) 4 kVRated voltage (III/2)320 VRated voltage (II/2)630 VConnection in acc. with standard EN-VDENominal current I N12 ANominal voltage U N250 VNominal cross section 2.5 mm2Maximum load current12 A (with 2.5 mm2 conductor cross section) Insulating material PAInflammability class acc. to UL 94V0Internal cylindrical gage A3Stripping length7 mmConnection dataConductor cross section solid min.0.2 mm2Conductor cross section solid max. 2.5 mm2Conductor cross section stranded min.0.2 mm2Conductor cross section stranded max. 2.5 mm2Conductor cross section stranded, with ferrule0.25 mm2without plastic sleeve min.Conductor cross section stranded, with ferrule2.5 mm2without plastic sleeve max.Conductor cross section stranded, with ferrule0.25 mm2with plastic sleeve min.Conductor cross section stranded, with ferrule2.5 mm2with plastic sleeve max.Conductor cross section AWG/kcmil min.24Conductor cross section AWG/kcmil max122 conductors with same cross section, solid min.0.2 mm22 conductors with same cross section, solid max. 1 mm22 conductors with same cross section, stranded0.2 mm2min.2 conductors with same cross section, stranded1.5 mm2max.2 conductors with same cross section, stranded,0.25 mm2ferrules without plastic sleeve, min.2 conductors with same cross section, stranded,1 mm2ferrules without plastic sleeve, max.2 conductors with same cross section, stranded,0.5 mm2TWIN ferrules with plastic sleeve, min.2 conductors with same cross section, stranded,1.5 mm2TWIN ferrules with plastic sleeve, max.Certificates / ApprovalsApproval logoCSANominal voltage U N300 VNominal current I N10 AAWG/kcmil28-12CULNominal voltage U N300 VNominal current I N10 AAWG/kcmil30-12ULNominal voltage U N300 VNominal current I N10 AAWG/kcmil30-12Certification CSA, CUL, GOST, ULAccessoriesItem Designation DescriptionTools1205053SZS 0,6X3,5Screwdriver, bladed, matches all screw terminal blocks up to 4.0mm² connection cross section, blade: 0.6 x 3.5 mm, without VDEapprovalAdditional productsItem Designation DescriptionGeneral1824007ICC 2,5/18-STZ-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 18, type of connection: Crimpconnection1788884MSTBVK 2,5/18-G-5,08Header, nominal current: 12 A, rated voltage: 320 V, pitch: 5.08mm, no. of positions: 18, mounting: Mounting rail1788693MVSTBU 2,5/18-GB-5,08Header, nominal current: 12 A, rated voltage: 320 V, pitch: 5.08mm, no. of positions: 18, mounting: Direct mounting1769625SMSTB 2,5/18-G-5,08Header, nominal current: 12 A, rated voltage: 250 V, pitch: 5.08mm, no. of positions: 18, mounting: Soldering3002034UK 3-MSTB-5,08Modular terminal blocks with plug entry, cross section: 0.2 - 2.5mm², AWG: 30 - 12, width: 5.1 mm, color: gray3002076UK 3-MVSTB-5,08Modular terminal blocks with plug entry, cross section: 0.2 - 2.5mm², AWG: 26 - 12, width: 5.1 mm, color: gray3002102UK 3-MVSTB-5,08-LA 24RD Modular terminal block with plug entry, nominal current: 12 A,rated voltage: 320 V, pitch: 5.08 mm, no. of positions: 1, mounting:mounting rail, with red light indicator, voltage light indicator: 24 VAC/DC, current light indicator: 3.3 mA3002063UK 3-MVSTB-5,08/EK Modular terminal blocks with plug entry, cross section: 0.2-2.5mm², AWG: 26-12, width: 5.1 mm, color: blue3002131UK 3D-MSTBV-5,08Modular terminal blocks with vertical plug entry, cross section: 0.2- 2.5 mm, AWG: 30 - 12, width: 5.1 mm, color: gray3002144UK 3D-MSTBV-5,08-LA 24RD Modular terminal block with vertical plug entry, color: Gray, withred light indicator, voltage light indicator: 24 V AC/DC, current lightindicator: 3.3 mA3002173UK 3D-MSTBV-5,08/EK Modular terminal blocks with plug entry, cross section: 0.2 - 2.5mm², AWG: 30 - 12, width: 5.1 mm, color: blue2770888UKK 3-MSTB-5,08Modular terminal blocks with 2 horizontal plug entries, crosssection: 0.2 - 2.5 mm, AWG: 30 - 12, width: 5.1 mm, color: gray 1876615UKK 3-MSTB-5,08-PE Ground terminal block, with 2 horizontal plug entries, nominalcurrent: 12 A, rated voltage: 320 V, pitch: 5.08 mm, no. ofpositions: 1, mounting: mounting rail.2770846UKK 3-MSTBVH-5,08Modular terminal blocks with vertical and horizontal plug entry,cross section: 0.2 - 2.5 mm, AWG: 30 - 12, width: 5.1 mm, color:gray1788279UMSTBVK 2,5/18-G-5,08Header, nominal current: 12 A, rated voltage: 320 V, pitch: 5.08mm, no. of positions: 18, mounting: Mounting rail1873016ZFKK 1,5-MSTBV-5,08Modular terminal blocks with plug entry, cross section: 0.2 - 1.5mm², width: 5.1 mm, color: grayDrawingsDimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。
1832581中文资料
Extract from the onlinecatalogGMVSTBR 2,5/ 8-ST-7,62Order No.: 1832581The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1832581Plug component, nominal current: 12 A, rated voltage: 500 V, pitch: 7.62 mm, no. of positions: 8, type of connection: Screw connectionhttp://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsPitch7.62 mmDimension a53.34 mmNumber of positions8Screw thread M 3Tightening torque, min0.5 NmTechnical dataInsulating material group IRated surge voltage (III/3) 6 kV Rated surge voltage (III/2) 6 kV Rated surge voltage (II/2) 6 kV Rated voltage (III/2)630 V Rated voltage (II/2)1000 V Connection in acc. with standard EN-VDE Nominal current I N12 A Nominal voltage U N500 V Nominal cross section 2.5 mm2 Maximum load current12 A Insulating material PA Inflammability class acc. to UL 94V0 Internal cylindrical gage A3 Stripping length7 mmConnection dataConductor cross section solid min.0.2 mm2 Conductor cross section solid max. 2.5 mm2 Conductor cross section stranded min.0.2 mm2 Conductor cross section stranded max. 2.5 mm2 Conductor cross section stranded, with ferrule0.25 mm2 without plastic sleeve min.Conductor cross section stranded, with ferrule2.5 mm2 without plastic sleeve max.Conductor cross section stranded, with ferrule0.25 mm2 with plastic sleeve min.Conductor cross section stranded, with ferrule2.5 mm2 with plastic sleeve max.Conductor cross section AWG/kcmil min.24 Conductor cross section AWG/kcmil max122 conductors with same cross section, solid min.0.2 mm2 2 conductors with same cross section, solid max. 1 mm22 conductors with same cross section, stranded0.2 mm2 min.2 conductors with same cross section, stranded1.5 mm2max.2 conductors with same cross section, stranded,0.25 mm2ferrules without plastic sleeve, min.2 conductors with same cross section, stranded,1 mm2ferrules without plastic sleeve, max.2 conductors with same cross section, stranded,0.5 mm2TWIN ferrules with plastic sleeve, min.2 conductors with same cross section, stranded,1 mm2TWIN ferrules with plastic sleeve, max.Certificates / ApprovalsCSANominal voltage U N300 VNominal current I N10 AAWG/kcmil28-12CULNominal voltage U N300 VNominal current I N10 AAWG/kcmil30-12ULNominal voltage U N300 VNominal current I N10 AAWG/kcmil30-12Certification CB, CSA, CUL, GOST, UL, VDE-PZIAccessoriesItem Designation DescriptionMarking0804549SK 7,62/3,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 10-section markerstrip, 12 identical decades marked 1-10, 11-20 etc. up to 91-99,sufficient for 120 terminal blocksPlug/Adapter1734634CP-MSTB Coding profile, is inserted into the slot on the plug or invertedheader, red insulating materialTools1205053SZS 0,6X3,5Screwdriver, bladed, matches all screw terminal blocks up to 4.0mm² connection cross section, blade: 0.6 x 3.5 mm, without VDEapprovalAdditional productsItem Designation DescriptionGeneral1828867GIC 2,5/ 8-ST-7,62Plug component, nominal current: 12 A, rated voltage: 400 V,pitch: 7.62 mm, no. of positions: 8, type of connection: Screwconnection1766181GMSTB 2,5/ 8-G-7,62Header, nominal current: 12 A, rated voltage: 400 V, pitch: 7.62mm, no. of positions: 8, mounting: Soldering1766291GMSTBA 2,5/ 8-G-7,62Header, nominal current: 12 A, rated voltage: 400 V, pitch: 7.62mm, no. of positions: 8, mounting: Soldering1766628GMSTBV 2,5/ 8-G-7,62Header, nominal current: 12 A, rated voltage: 400 V, pitch: 7.62mm, no. of positions: 8, mounting: Soldering1766835GMSTBVA 2,5/ 8-G-7,62Header, nominal current: 12 A, rated voltage: 400 V, pitch: 7.62mm, no. of positions: 8, mounting: SolderingDrawingsDimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。
AME8500BEFVDE28中文资料
1AME8500 / 8501µProcessor Supervisoryl Small packages: SOT-23, SOT-89l 11 voltage threshold optionsl Tight voltage threshold tolerance ---±1.50%l 5 reset interval options l 4 output configuration optionsl Wide temperature range -------- -40o C to 85o C l Low temperature coefficient --- 100ppm/o C (max)l Low quiescent current < 3.0µA l Thermal shutdown option (AME8501)The AME8500 family allows the user to customize the CPU reset function without any external components.The user has a large choice of reset voltage thresholds,reset time intervals, and output driver configurations, all of which are preset at the factory. Each wafer is trimmed to the customer's specifications.These circuits monitor the power supply voltage of µP based systems. When the power supply voltage drops below the voltage threshold a reset is asserted immedi-ately (within an interval T D1). The reset remains asserted after the supply voltage rises above the voltage threshold for a time interval, T D2 . The reset output may be either active high (RESET) or active low (RESETB). The reset output may be configured as either push/pull or open drain. The state of the reset output is guaranteed to be correct for supply voltages greater than 1V.The AME8501 includes all the above functionality plus an overtemperature shutdown function. When the ambi-ent temperature exceeds 80o C a reset is asserted and remains asserted until the temperature falls below 60o C.Space saving SOT23 packages and micropower qui-escent current (<3.0µA) make this family a natural for portable battery powered equipment.n General Descriptionn Featuresn Typical Operating CircuitNote: * External pull-up resistor is required if open-drain output is used. 10 k Ω is recommended.n Block Diagraml Portable electronics l Power suppliesl Computer peripherals l Data acquisition systems l Applications using CPUs l Consumer electronicsn ApplicationsAME8500 with Push-Pull RESETVV DDRESETAME8500 with Push-Pull RESET2µProcessor SupervisoryAME8500 / 8501n Block Diagram (contd.)AME8500AEET AME8501AEET 1.GND2.Reset/ResetB3.V DDSOT-23Top View123n Pin ConfigurationSOT-23Top View123SOT-23Top ViewAME8500CEET AME8501CEET 1.Reset/ResetB 2.V DD 3.GND123AME8500BEET AME8501BEET 1.Reset/ResetB 2.GND 3.V DDAME8500 with Open-Drain RESETV AME8500 with Open-Drain RESETV DDAME8500AEET AME8501AEET 1.GND2.Reset/ResetB3.V DDSOT-23-L Top View1233AME8500 / 8501µProcessor Supervisoryn Pin Configuration (contd.)SOT-89Top ViewSOT-89Top ViewSOT-89Top ViewAME8500AEFT AME8501AEFT 1.GND 2.V DD3.Reset/ResetBAME8500CEFT AME8501CEFT 1.V DD 2.GND3.Reset/ResetBAME8500BEFT AME8501BEFT 1.Reset/ResetB 2.V DD 3.GND132132132SOT-23-L Top ViewAME8500BEET AME8501BEET 1.Reset/ResetB 2.GND 3.V DD123SOT-23-L Top ViewAME8500CEET AME8501CEET 1.Reset/ResetB 2.VDD 3.GND123SOT-25Top ViewAME8500BEEV AME8501BEEV 1.Reset/ResetB 2.V DD 3.GND 4.N/C 5.N/C132544µProcessor SupervisoryAME8500 / 8501n Ordering InformationOperating Temperature Range Number of Pins Package TypePin ConfigurationSpecial FeatureAME8501 x x x x x x x xOutput Driver Option Reset Time (T D2NOM )VDD Threshold Voltage (V TH )AME8500 x x x x x x x x A1. GND E:-40O C to 85O C E:SOT-2X T:3A:RESETB /PP A:1.5 ms 15:VTH= 1.5V L:Low profile (SOT-23)2. Reset/F:SOT-89V:5B:RESETB /OD D:30 ms 16:VTH= 1.6V Y: ResetB C:RESET/ PP E:150 ms 18:VTH= 1.8V 3. VDD D:RESET/ OD F:210 ms19:VTH= 1.9V Z:Lead free B1. Reset/20:VTH=2.0V (SOT-23)ResetB 21:VTH= 2.1V 2. GND 22:VTH= 2.2V 3. VDD 23:VTH= 2.32V C1. Reset/24:VTH=2.4V (SOT-23)ResetB 26:VTH= 2.63V 2. VDD 27:VTH= 2.7V 3. GND 28:VTH= 2.8V A1. GND 29:VTH=2.93V (SOT-89)2. VDD 31:VTH=3.08V 3. Reset/40:VTH=4.0V ResetB 42:VTH= 4.2V B1. Reset/44:VTH= 4.38V (SOT-89)ResetB 46:VTH= 4.63V2. VDD3. GND C1. VDD (SOT-89)2. GND3. Reset/ ResetBLead free &Low profile Output DriverOptionCharacteristicof RESET orRESETB pinSpecial FeatureReset Time (T D2NOM )VDD Threshold Voltage (V TH )PackageTypeNumber of Pins Operating TemperatureRangePinConfiguration (PP = Push pull out)(RESET = Active High)(RESETB = Active Low)(OD = Open drain output polarity )AME8500 / 8501µProcessor Supervisory n Ordering Information6µProcessor SupervisoryAME8500 / 8501n Ordering Information (contd.)AME8500 / 8501µProcessor Supervisory n Ordering Information (contd.)Please consult AME sales office or authorized Rep./Distributor for other voltage options.78µProcessor SupervisoryAME8500 / 8501n Absolute Maximum RatingsCaution: Stress above the listed absolute maximum rating may cause permanent damage to the deviceAME8500 / 8501µProcessor Supervisory910µProcessor SupervisoryAME8500 / 8501n Timing Diagramn Applications InformationSupply TransientsThese devices have a certain immunity to fast negative going transients. In the following pages the graph titled “Glitch Rejection” indicates the maximum allowable glitch amplitude and duration to avoid triggering an unintended reset. As shown in the graph shorter transients can have larger amplitudes without triggering resets.Glitch Rejection Reset Time vs. TemperatureGlitchDuration(µS)Glitch Amplitude (V)204060801001201400.010.11ResetTime(mS)190195200205210215220-45-5255585115Temperature (o C)11AME8500 / 8501µProcessor SupervisoryI DD vs. V DDThreshold Hysteresis vs. TemperatureT D1 Delay vs. TemperatureI DD vs. TemperatureReset V TH vs. TemperatureReset VOL vs. TemperatureS u p p l y C u r r e n t @ 5V (u A )Temperature (o C)2.102.152.202.252.302.35-45-52555851152.6302.6322.6342.6362.6382.6402.6422.6442.6462.6482.650-45-5255585115R e s e t V t h (V )Temperature (oC)I D D (u A )V DD (V)0.40.81.21.6012345TD 2 D e l a y (u S )Temperature (o C)37383940414243-40-20020406080100H y s t e r es i s (% o f V T H )Temperature (o C)00.10.20.30.40.5-40-200204060801000.2200.2250.2300.2350.2400.2450.2500.2550.2600.265-45-5255585115Re s e t V O L @ 0.8m A (V )Temperature (o C)12µProcessor SupervisoryAME8500 / 8501n Package DimensionSOT-23c 1Top ViewSide ViewSOT-23-Lc 1Top ViewSide View13AME8500 / 8501µProcessor Supervisoryn Package DimensionSOT-89Top View Side ViewCSOT-25Top ViewSide ViewFront View。
LTC1858IG中文资料
1185789f100ksps SoftSpan A/D Converterswith ShutdownThe LTC ®1857/LTC1858/LTC1859 are 8-channel, low power, 12-/14-/16-bit, 100ksps, analog-to-digital con-verters (ADCs). These SoftSpan TM ADCs can be software-programmed for 0V to 5V, 0V to 10V, ±5V or ±10V input spans and operate from a single 5V supply. The 8-chan-nel multiplexer can be programmed for single-ended inputs or pairs of differential inputs or combinations of both. In addition, all channels are fault protected to ±25V.A fault condition on any channel will not affect the conversion result of the selected channel.An onboard high performance sample-and-hold and pre-cision reference minimize external components. The low 40mW power dissipation is made even more attractive with two user selectable power shutdown modes. DC speci-fications include ±3LSB INL for the LTC1859, ±1.5LSB INL for the LTC1858 and ±1LSB for the LTC1857.The internal clock is trimmed for 5µs maximum conver-sion time and the sampling rate is guaranteed at 100ksps.A separate convert start input and data ready signal (BUSY)ease connections to FIFOs, DSPs and microprocessors.■Sample Rate: 100ksps■8-Channel Multiplexer with ±25V Protection ■Single 5V Supply■Software-Programmable Input Ranges:0V to 5V, 0V to 10V, ±5V or ±10V Single Ended or Differential■±3LSB INL for the LTC1859, ±1.5LSB INL for the LTC1858, ±1LSB INL for the LTC1857■Power Dissipation: 40mW (Typ)■SPI/MICROWIRE TM Compatible Serial I/O ■Power Shutdown: Nap and Sleep■Signal-to-Noise Ratio: 87dB (Typ) for the LTC1859■Operates with Internal or External Reference ■Internal Synchronized Clock ■28-Pin SSOP Package±5V OR ±100kHz, 12-Bit/14-Bit/16-Bit Sampling ADC■Industrial Process Control■Multiplexed Data Acquisition Systems ■High Speed Data Acquisition for PCs ■Digital Signal ProcessingMICROWIRE is a trademark of National Semiconductor Corporation.CODE–32768I N L (L S B )00.51.001859 TA02–0.5–1.0–2.0–163841638432767–1.52.01.5LTC1859 Typical INL CurveDESCRIPTIOUFEATURESAPPLICATIO SUTYPICAL APPLICATIOU2LTC1857/LTC1858/LTC1859185789fA U G WA WU W A R BSOLUTEXI TI SSupply Voltage (OV DD = DV DD = AV DD = V DD )........... 6V Ground Voltage DifferenceDGND, AGND1, AGND2, AGND3...................... ±0.3V Analog Input Voltage ADC +, ADC –(Note 3)...................(AGND1 – 0.3V) to (AV DD + 0.3V)CH0-CH7, COM..................................................±25V Digital Input Voltage (Note 4)......(DGND – 0.3V) to 10V Digital Output Voltage....(DGND – 0.3V) to (DV DD + 0.3V)Power Dissipation..............................................500mW Operating Temperature RangeLTC1857C/LTC1858C/LTC1859C............ 0°C to 70°C LTC1857I/LTC1858I/LTC1859I .......... –40°C to 85°C Storage Temperature Range .................–65°C to 150°C Lead Temperature (Soldering, 10 sec)................. 300°C(Notes 1, 2)Consult LTC Marketing for parts specified with wider operating temperature ranges.PACKAGE/ORDER I FOR ATIOU U WThe ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at T A = 25°C.MUXOUT connected to ADC inputs. (Notes 5, 6)CO VERTER A D ULTIPLEXER CHARACTERISTICSUW ULTC1857LTC1858LTC1859PARAMETER CONDITIONSMIN TYP MAXMIN TYP MAXMIN TYP MAXUNITS Resolution●121416Bits No Missing Codes ●121415Bits Transition Noise0.060.261LSB RMSIntegral Linearity Error (Notes 7, 15)●±1±1.5±3LSB Differential Linearity Error (Note 15)●–11–11.5–24LSB Bipolar Zero Error (Note 8)●±9±17±28LSB Bipolar Zero Error Drift ±0.1±0.1±0.1ppm/°C Bipolar Zero Error Match ±4±6±10LSB Unipolar Zero Error (Note 8)●±6±15±25LSB Unipolar Zero Error Drift ±1±1±1ppm/°C Unipolar Zero Error Match ±1.2±2±8LSB Bipolar Full-Scale Error External Reference (Note 11)●±0.35±0.15±0.1%Internal Reference (Note 11)±0.45±0.40±0.4%Bipolar Full-Scale Error Drift External Reference ±2.5±2.5±2.5ppm/°C Internal Reference±7±7±7ppm/°C Bipolar Full-Scale Error Match ±5±10±15LSB Unipolar Full-Scale Error External Reference (Note 11)●±0.45±0.25±0.20%Internal Reference (Note 11)±0.75±0.85±0.75%Unipolar Full-Scale Error Drift External Reference ±2.5±2.5±2.5ppm/°C Internal Reference ±7±7±7ppm/°C Unipolar Full-Scale Error Match ±5±12±15LSB Input Common Mode Range Unipolar Mode ●0 to 100 to 100 to 10V Bipolar Mode●±10±10±10V Input Common Mode Rejection Ratio969696dB3LTC1857/LTC1858/LTC1859185789fThe ● denotes the specifications which apply over the full operating temperature range, otherwisespecifications are at T A = 25°C. (Note 5)A ALOG I PUT UUPARAMETER CONDITIONS MINTYP MAX UNITSAnalog Input RangeCH0 to CH7, COM 0 to 5, 0 to 10V ±5, ±10V ADC +, ADC – (Note 3)0 to 2.048V 0 to 4.096V ADC – ±1.024V ADC – ±2.048V ImpedanceCH0 to CH7, COM Unipolar 42k Ω Bipolar31k ΩMUXOUT +, MUXOUT – Unipolar 10k Ω Bipolar 5k ΩADC +, ADC –Hi-Z k ΩCapacitanceCH0 to CH7, COM 5pF Sample Mode ADC +, ADC – 0V to 2.048V, ±1.024V 24pF 0V to 4.096V, ±2.048V 12pF Hold Mode ADC +, ADC –4pFInput Leakage CurrentADC +, ADC –, CONVST = Low●±1µAThe ● denotes the specifications which apply over the full operating temperature range,otherwise specifications are at T A = 25°C. MUXOUT connected to ADC inputs. (Notes 5 and 12)LTC1857LTC1858LTC1859SYMBOL PARAMETERCONDITIONS MIN TYP MAXMIN TYP MAXMIN TYP MAXUNITS S/(N + D)Signal-to-(Noise + Distortion) Ratio 1kHz Input Signal748387dB THDTotal Harmonic Distortion1kHz Input Signal,–101–101–101dB First Five Harmonics Peak Harmonic or Spurious Noise 1kHz Input Signal –103–103–103dB Channel-to-Channel Isolation 1kHz Input Signal–120–120–120dB –3dB Input Bandwidth 111MHz Aperture Delay –70–70–70ns Aperture Jitter 606060ps Transient Response Full-Scale Step 444µs (Note 9)Overvoltage Recovery(Note 13)150150150nsDY A IC ACCURACYUW4LTC1857/LTC1858/LTC1859185789fThe ● denotes the specifications which apply over thefull operating temperature range, otherwise specifications are at T A = 25°C. (Note 5)PARAMETER CONDITIONS MIN TYP MAX UNITSV REF Output VoltageI OUT = 0●2.4752.50 2.525V V REF Output Temperature Coefficient I OUT = 0±10ppm/°CV REF Output Impedance –0.1mA ≤ I OUT ≤ 0.1mA 8k ΩV REFCOMP Output VoltageI OUT = 04.096VThe ● denotes the specifications which apply over thefull operating temperature range, otherwise specifications are at T A = 25°C. (Note 5)SYMBOL PARAMETERCONDITIONS MINTYP MAX UNITSV IH High Level Input Voltage V DD = 5.25V ● 2.4V V IL Low Level Input Voltage V DD = 4.75V ●0.8V I IN Digital Input Current V IN = 0V to V DD●±10µA C IN Digital Input Capacitance 5pF V OH High Level Output Voltage V DD = 4.75V, I O = –10µA, OV DD = V DD 4.74V V DD = 4.75V, I O = –200µA, OV DD = V DD ●4VV OL Low Level Output Voltage V DD = 4.75V, I O = 160µA, OV DD = V DD 0.05V V DD = 4.75V, I O = 1.6mA, OV DD = V DD ●0.100.4V I OZ Hi-Z Output Leakage V OUT = 0V to V DD , RD = High ●±10µA C OZ Hi-Z Output Capacitance RD = High 15pF I SOURCE Output Source Current V OUT = 0V –10mA I SINKOutput Sink CurrentV OUT = V DD10mAI TER AL REFERE CE CHARACTERISTICSU U UDIGITAL I PUTS A D DIGITAL OUTPUTSUU PARAMETER CONDITIONS MIN TYP MAX UNITSPositive Supply Voltage (Notes 9 and 10)4.755.00 5.25V Positive Supply Current ●8.013mA Nap Mode 5.58mA Sleep Mode CONVST = 0V or 5V8.015µA Power Dissipation 40.0mW Nap Mode 27.5mW Sleep ModeCONVST = 0V or 5V40.0µWThe ● denotes the specifications which apply over the full operating temperaturerange, otherwise specifications are at T A = 25°C. (Note 5)POWER REQUIRE E T SWU5LTC1857/LTC1858/LTC1859185789fThe ● denotes the specifications which apply over the full operating temperaturerange, otherwise specifications are at T A = 25°C. (Note 5)TI I G CHARACTERISTICSUW SYMBOLPARAMETERCONDITIONSMIN TYP MAX UNITS f SAMPLE(MAX)Maximum Sampling Frequency Through CH0 to CH7 Inputs ●100kHz Through ADC +, ADC – Only166kHzt CONV Conversion Time ●45µs t ACQ Acquisition Time Through CH0 to CH7 Inputs ●4µs Through ADC +, ADC – Only 1µs f SCK SCK Frequency (Note 14)●020MHz t r SDO Rise Time See Test Circuits 6ns t f SDO Fall Time See Test Circuits6ns t 1CONVST High Time ●40nst 2CONVST to BUSY Delay C L = 25pF, See Test Circuits ●1530ns t 3SCK Period ●50ns t 4SCK High ●10ns t 5SCK Low●10nst 6Delay Time, SCK ↓ to SDO Valid C L = 25pF, See Test Circuits ●2545ns t 7Time from Previous SDO Data Remains C L = 25pF, See Test Circuits ●520nsValid After SCK ↓t 8SDO Valid After RD ↓C L = 25pF, See Test Circuits ●1130ns t 9RD ↓ to SCK Setup Time ●20ns t 10SDI Setup Time Before SCK ↑●0ns t 11SDI Hold Time After SCK ↑●7ns t 12SDO Valid Before BUSY ↑RD = Low, C L = 25pF, See Test Circuits ●520nst 13Bus Relinquish TimeSee Test Circuits●1030nsNote 1: Absolute maximum ratings are those values beyond which the life of a device may be impaired.Note 2: All voltage values are with respect to ground with DGND, AGND1,AGND2 and AGND3 wired together unless otherwise noted.Note 3: When these pin voltages are taken below ground or above AV DD =DV DD = OV DD = V DD , they will be clamped by internal diodes. This product can handle currents of greater than 100mA below ground or above V DD without latchup.Note 4: When these pin voltages are taken below ground they will be clamped by internal diodes. This product can handle currents of greater than 100mA below ground without latchup. These pins are not clamped to V DD .Note 5: V DD = 5V, f SAMPLE = 100kHz, t r = t f = 5ns unless otherwise specified.Note 6: Linearity, offset and full-scale specifications apply for a single-ended analog MUX input with respect to ground or ADC + with respect to ADC – tied to ground.Note 7: Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual end points of the transfer curve.The deviation is measured from the center of the quantization band.Note 8: Bipolar zero error is the offset voltage measured from –0.5LSB when the output code flickers between 0000 0000 0000 0000 and 11111111 1111 1111 for the LTC1859, between 00 0000 0000 0000 and 111111 1111 1111 for the LTC1858 and between 0000 0000 0000 and 11111111 1111 for the LTC1857. Unipolar zero error is the offset voltagemeasured from 0.5LSB when the output codes flicker between 0000 00000000 0000 and 0000 0000 0000 0001 for the LTC1859, between 00 00000000 0000 and 00 0000 0000 0001 for the LTC1858 and between 00000000 0000 and 0000 0000 0001 for the LTC1857.Note 9: Guaranteed by design, not subject to test.Note 10: Recommended operating conditions.Note 11: Full-scale bipolar error is the worst case of –FS or +FSuntrimmed deviation from ideal first and last code transitions, divided by the full-scale range, and includes the effect of offset error. For unipolar full-scale error, the deviation of the last code transition from ideal, divided by the full-scale range, and includes the effect of offset error.Note 12: All Specifications in dB are referred to a full-scale ±10V input.Note 13: Recovers to specified performance after (2 • FS) input overvoltage.Note 14: t 6 of 45ns maximum allows f SCK up to 10MHz for rising capture with 50% duty cycle and f SCK up to 20MHz for falling capture (with 5ns setup time for the receiving logic).Note 15: The specification is referred to the ±10V input range.6LTC1857/LTC1858/LTC1859185789fTYPICAL PERFOR A CE CHARACTERISTICSU WLTC1859 Nonaveraged 4096-Point FFT PlotLTC1859 SINAD vs Input FrequencyLTC1859 Total Harmonic Distortion vs Input FrequencyLTC1859 Typical INL CurveLTC1859 Typical DNL CurveLTC1859 Channel-to-Channel Offset Error Matching vs TemperatureCODE–32768D N L (L S B )00.51.001859 G02–0.5–1.0–2.0–163841638432767–1.52.01.5FREQUENCY (kHz)01525501869 G035102030404535M A G N I T U D E (d B )–60–40–200–80–100–70–50–30–10–90–110–130–120f SAMPLE = 100kHz f IN = 1kHzSINAD = 86.95dB THD = –101.42dBINPUT FREQUENCY (kHz)174S I N A D (d B )788290101001859 G048676808884INPUT FREQUENCY (kHz)1–110T O T A L H A R M O N I C D I S T O R T I O N (d B )–100–90–70101001859 G05–80TEMPERATURE (°C)–50–1.0C H A N N E L -T O -C HA N N E L O F F S E T E R R O R M A T C H IN G (L S B s )–0.50.51.0–25025501959 G0675100BIPOLAR MODEUNIPOLAR MODECODE–32768I N L (L S B )00.51.001859 TA02–0.5–1.0–2.0–163841638432767–1.52.01.5Change in REFCOMP Voltage vs Load CurrentInternal Reference Voltage vs TemperatureLTC1859 Channel-to-Channel Gain Error Matching vs TemperatureTEMPERATURE (°C)–50–1.0C H A N N E L -T O-C H A N N E L G A I N E R R O R M A T C H I N G (L S B s )–0.50.51.0–25025501959 G0775100TEMPERATURE (°C)–50I N T E R N A L R E F E R E N C E V O L T A G E (V )25751859 G08–25502.5202.5152.5102.5052.5002.4952.4902.4852.480100LOAD CURRENT (mA)–50–0.04C H A N G E I N R E F C O M P V O L T A G E (V )–0.020.020.04–40–30–20–101859 G090107LTC1857/LTC1858/LTC1859185789fTYPICAL PERFOR A CE CHARACTERISTICSU WU U UPI FU CTIO SCOM (Pin 1): Common Input. This is the reference point for all single-ended inputs. It must be free of noise and is usually connected to the analog ground plane.CH0 (Pin 2): Analog MUX Input.CH1 (Pin 3): Analog MUX Input.CH2 (Pin 4): Analog MUX Input.CH3 (Pin 5): Analog MUX Input.CH4 (Pin 6): Analog MUX Input.CH5 (Pin 7): Analog MUX Input.CH6 (Pin 8): Analog MUX Input.CH7 (Pin 9): Analog MUX Input.MUXOUT + (Pin 10): Positive MUX Output. Output of the analog multiplexer. Connect to ADC + for normal operation.MUXOUT – (Pin 11): Negative MUX Output. Output of the analog multiplexer. Connect to ADC – for normal operation.ADC + (Pin 12): Positive Analog Input to the Analog-to-Digital Converter.ADC – (Pin 13): Negative Analog Input to the Analog-to-Digital Converter.AGND1 (Pin 14): Analog Ground.V REF (Pin 15): 2.5V Reference Output. Bypass to analog ground with a 1µF tantalum capacitor.REFCOMP (Pin 16): Reference Buffer Output. Bypass to analog ground with a 10µF tantalum and a 0.1µF ceramic capacitor. Nominal output voltage is 4.096V.AGND2 (Pin 17): Analog Ground.AGND3 (Pin 18): Analog Ground. This is the substrate connection.AV DD (Pin 19): 5V Analog Supply. Bypass to analog ground with a 0.1µF ceramic and a 10µF tantalum capacitor.DV DD (Pin 20): 5V Digital Supply. Bypass to digital ground with a 0.1µF ceramic and a 10µF tantalum capacitor.OV DD (Pin 21): Positive Supply for the Digital Output Buffers (3V to 5V). Bypass to digital ground with a 0.1µF ceramic and a 10µF tantalum capacitor.BUSY (Pin 22): Output shows converter status. It is low when a conversion is in progress.SDO (Pin 23): Serial Data Output.LTC1859 Power SupplyFeedthrough vs Ripple FrequencySupply Current vs Supply VoltageSupply Current vs TemperatureRIPPLE FREQUENCY (Hz)–60P O W E R S U P P L Y F E E D T H R O U G H (d B )–40–20–1010010k 100k 1M1859 G10–801k –30–50–70SUPPLY VOLTAGE (V)4.5S U P P L Y C U R R E N T (m A )8.08.55.51859 G117.57.0 4.755 5.259.0TEMPERATURE (°C)–507.0P O S I T I V E S U P P L Y C U R R E N T (m A )7.58.08.59.0–25025501859 G12751008LTC1857/LTC1858/LTC1859185789fU UWFU CTIO AL BLOCK DIAGRACONVST SDIBUSYSCKRD OV DD SDOCOMCH7CH1•••CH0DGND (Pin 24): Digital Ground.SDI (Pin 25): Serial Data Input.SCK (Pin 26): Serial Data Clock.U U UPI FU CTIO SRD (Pin 27):Read Input. This active low signal enables the digital output pin SDO.CONVST (Pin 28): Conversion Start. This active high signal starts a conversion on its rising edge.Load Circuits for Access Timing(A) Hi-Z TO V OH AND V OL TO V OH(B) Hi-Z TO V OL AND V OH TO V OL1859 TC01Load Circuits for Output Float Delay(A) V OH TO Hi-Z (B) V OL TO Hi-Z1859 TC02TEST CIRCUITS9LTC1857/LTC1858/LTC1859185789ft 1 (For Short Pulse Mode)t 2 (CONVST to BUSY Delay)t 3, t 4, t 5 (SCK Timing)t 6 (Delay Time, SCK ↓ to SDO Valid)t 7 (Time from Previous Data Remains Valid After SCK ↓)t 8↓)t 9 (RD ↓ to SCK Setup Time)RDSCKt 10 (SDI Setup Time Before SCK ↑)t 11 (SDI Hold Time After SCK ↑)TI I G DIAGRA SWU W t 12 (SDO Valid Before BUSY ↑, RD = 0)t 13(BUS Relinquish Time)10LTC1857/LTC1858/LTC1859185789fAPPLICATIO S I FOR ATIOW UUU OVERVIEWThe LTC1857/LTC1858/LTC1859 are innovative, multi-channel ADCs that provide software-selectable input ranges for each of their eight input channels. Using on-chip resistors and switches, it provides an attenuation and offset that can be programmed for each channel on the fly.The precisely trimmed attenuators ensure accurate input ranges. Because they precede the multiplexer, errors due to multiplexer on-resistance are eliminated.The input word that selects the input channel also selects the desired input range for that channel. The available ranges are 0V to 5V, 0V to 10V (unipolar), ±5V and ±10V (bipolar). They are achieved with the ADC running on a single 5V supply. In addition to the range selection, single ended or differential inputs may be selected for each channel or pair of channels. Finally, overrange protection is provided for unselected channels. An overrange condi-tion on an unused channel will not affect the conversion result on the selected channel.CONVERSION DETAILSThe LTC1857/LTC1858/LTC1859 use a successive approxi-mation algorithm and an internal sample-and-hold circuit to convert an analog signal to a 12-/14-/16-bit serial out-put respectively. The ADCs are complete with a precision reference and an internal clock. The control logic provides easy interface to microprocessors and DSPs. (Please refer to the Digital Interface section for the data format.)The analog signals applied at the MUX input channels are rescaled by the resistor divider network formed by R1, R2and R3 as shown below. The rescaled signals appear on the MUXOUT (Pins 10, 11) which are also connected to the ADC inputs (Pins 12, 13) under normal operation.Before starting a conversion, an 8-bit data word is clocked into the SDI input on the first eight rising SCK edges to select the MUX address, input range and power down mode. The ADC enters acquisition mode on the falling edge of the sixth clock in the 8-bit data word and ends on the rising edge of the CONVST signal which also starts a conversion (see Figure 7). A minimum time of 4µs will provide enough time for the sample-and-hold capacitors to acquire the analog signal. Once a conversion cycle has begun, it cannot be restarted.During the conversion, the internal differential 12-/14-/16-bit capacitive DAC output is sequenced by the SAR from the most significant bit (MSB) to the least significant bit (LSB). The input is successively compared with the binary weighted charges supplied by the differential capacitive DAC. Bit decisions are made by a high speed comparator.At the end of a conversion, the DAC output balances the analog input (ADC + – ADC –). The SAR contents (a 16-bit data word) which represents the difference of ADC + and ADC – are loaded into the 12-/14-/16-bit shift register.DRIVING THE ANALOG INPUTSThe nominal input ranges for the LTC1857/LTC1858/LTC1859 are 0V to 5V, 0V to 10V, ±5V and ±10V and the MUX inputs are overvoltage protected to ±25V. The input impedance is typically 42k Ω in unipolar mode and 31k Ωin bipolar mode, therefore, it should be driven with a low impedance source. Wideband noise coupling into the input can be minimized by placing a 3000pF capacitor at the input as shown in Figure 2. An NPO-type capacitor gives the lowest distortion. Place the capacitor as close to the device input pin as possible. If an amplifier is to be used to drive the input, care should be taken to select an amplifier with adequate accuracy, linearity and noise for the application. The following list is a summary of the op amps that are suitable for driving the LTC1857/LTC1858/LTC1859. More detailed information is available in the Linear Technology data books and online at .LT ®1007: Low noise precision amplifier. 2.7mA supply current ±5V to ±15V supplies. Gain bandwidth product 8MHz. DC applications.MUXOUTLTC1857/LTC1858/LTC1859LT1227: 140MHz video current feedback amplifier. 10mA supply current. ±5V to ±15V supplies. Low noise and low distortion.LT1468/LT1469: Single and dual 90MHz, 16-bit accurate op amp. Good AC/DC specs.LT1677: Single, low noise op amp. Rail-to-rail input and output. Up to ±15V supplies.APPLICATIO S I FOR ATIOW UUU1859 F02A IN A IN Figure 2. Analog Input FilteringFigure 1. LTC1857/LTC1858/LTC1859 Simplified Equivalent CircuitLT1792: Single, low noise JFET input op amp, ±5V supplies.LT1793: Single, low noise JFET input op amp, 10pA bias current, ±5V supplies.LT1881/LT1882: Dual and quad, 200pA bias current, rail-to-rail output op amps. Up to ±15V supplies.LT1844/LT1885: Dual and quad, 400pA bias current, rail-to-rail output op amps. Up to ±15V supplies. Faster response and settling time.INTERNAL VOLTAGE REFERENCEThe LTC1857/LTC1858/LTC1859 have an on-chip, tem-perature compensated, curvature corrected, bandgap ref-erence, which is factory trimmed to 2.50V. The full-scale range of the LTC1857/LTC1858/LTC1859 is equal to ±5V,0V to 5V, ±10V or 0V to 10V. The output of the reference is connected to the input of a gain of 1.6384x buffer through an 8k resistor (see Figure 3). The input to theCONVST SDI BUSY SCKRD OV DD SDOCOMCH7CH1•••CH0LTC1857/LTC1858/LTC1859buffer or the output of the reference is available at V REF (Pin 15). The internal reference can be overdriven with an external reference if more accuracy is needed. The buffer output drives the internal DAC and is available at REFCOMP (Pin 16). The REFCOMP pin can be used to drive a steady DC load of less than 2mA. Driving an AC load is not recommended because it can cause the performance of the converter to degrade.successive integer LSB values (i.e., 0.5LSB, 1.5LSB,2.5LSB, … FS – 1.5LSB). The output code is natural binary with 1LSB = FS/65536. Figure 4b shows the input/output transfer characteristics for the bipolar mode in two’s complement format.FULL SCALE AND OFFSETIn applications where absolute accuracy is important,offset and full-scale errors can be adjusted to zero during a calibration sequence. Offset error must be adjusted before full-scale error. Zero offset is achieved by adjusting the offset applied to the “–” input. For single-ended inputs,this offset should be applied to the COM pin. For differen-tial inputs, the “–” input is dictated by the MUX address.For unipolar zero offset error, apply 0.5LSB (actual voltage will vary with input span selected) to the “+” input and adjust the offset at the “–” input until the output code flickers between 0000 0000 0000 0000 and 0000 00000000 0001 for the LTC1859, between 00 0000 0000 0000and 00 0000 0000 0001 for the LTC1858 and between 0000 0000 0000 and 0000 0000 0001 for the LTC1857.For bipolar zero error, apply –0.5LSB (actual voltage will vary with input span selected) to the “+” input and adjust the offset at the “–” input until the output code flickers between 0000 0000 0000 0000 and 1111 1111 11111111 for the LTC1859, between 00 0000 0000 0000 andAPPLICATIO S I FOR ATIOW UUU Figure 3. Internal or External Reference SourceINPUT VOLTAGE (V)O U T P U T C O D E1859 F4aLSBINPUT VOLTAGE (V)O U T P U T C O D ELSB 1859 F4bLSB Figure 4a. Unipolar Transfer Characteristics (UNI = 1)Figure 4b. Bipolar Transfer Characteristics (UNI = 0)For minimum code transition noise the V REF pin and the REFCOMP pin should each be decoupled with a capacitor to filter wideband noise from the reference and the buffer.UNIPOLAR /BIPOLAR OPERATIONFigure 4a shows the ideal input/output characteristics for the LTC1859. The code transitions occur midway betweenLTC1857/LTC1858/LTC1859APPLICATIO S I FOR ATIOW UUU Figure 5. LTC1859 Histogram for 4096 Conversions11 1111 1111 1111 for the LTC1858 and between 00000000 0000 and 1111 1111 1111 for the LTC1857.As mentioned earlier, the internal reference is factory trimmed to 2.50V. To make sure that the reference buffer gain is not compensating for trim errors in the reference,REFCOMP is trimmed with an accurate external 2.5V ref-erence applied to V REF . For unipolar inputs, an input volt-age of FS – 1.5LSBs should be applied to the “+” input and the appropriate reference adjusted until the output code flickers between 1111 1111 1111 1110 and 1111 11111111 1111 for the LTC1859, between 11 1111 1111 1110and 11 1111 1111 1111 for the LTC1858 and between 1111 1111 1110 and 1111 1111 1111 for the LTC1857.For bipolar inputs, an input voltage of FS – 1.5LSBs should be applied to the “+” input and the appropriate reference adjusted until the output code flickers between 0111 11111111 1110 and 0111 1111 1111 1111 for the LTC1859,between 01 1111 1111 1110 and 01 1111 1111 1111 for the LTC1858 and between 0111 1111 1110 and 0111 11111111 for the LTC1857.These adjustments as well as the factory trims affect all channels. The channel-to-channel offset and gain error matching are guaranteed by design to meet the specifica-tions in the Converter Characteristics table.DC PERFORMANCEOne way of measuring the transition noise associated with a high resolution ADC is to use a technique where a DC signal is applied to the input of the MUX and the resulting output codes are collected over a large number of conversions. For example in Figure 5 the distribution of output code is shown for a DC input that has been digitized 4096 times. The distribution is Gaussian and the RMS code transition is about 1LSB for the LTC1859.DIGITAL INTERFACE Internal ClockThe ADC has an internal clock that is trimmed to achieve a typical conversion time of 4µs. No external adjustments are required and, with the maximum acquisition time of 4µs,throughput performance of 100ksps is assured.3V Input/Output CompatibleThe LTC1857/LTC1858/LTC1859 operate on a 5V supply,which makes the devices easy to interface to 5V digital systems. These devices can also interface to 3V digitalsystems: the digital input pins (SCK, SDI, CONVST and RD) of the LTC1857/LTC1858/LTC1859 recognize 3V or 5V inputs. The LTC1857/LTC1858/LTC1859 have a dedi-cated output supply pin (OVP) that controls the output swings of the digital output pins (SDO, BUSY) and allows the part to interface to either 3V or 5V digital systems. The output is two’s complement binary for bipolar mode and offset binary for unipolar mode.Timing and ControlConversion start and data read are controlled by two digital inputs: CONVST and RD. To start a conversion and put the sample-and-hold into the hold mode bring CONVST high for no less than 40ns. Once initiated it cannot be restarted until the conversion is complete. Converter status is indicated by the BUSY output and this is low while the conversion is in progress.Figures 6a and 6b show two different modes of operation for the LTC1859. For the 12-bit LTC1857 and 14-bit LTC1858, the last four and two bits of the SDO will output zeros respectively. In mode 1 (Figure 6a), RD is tied low.The rising edge of CONVST starts the conversion. The data outputs are always enabled. The MSB of the data output is available after the conversion. In mode 2 (Figure 6b),CONVST and RD are tied together. The rising edge of the CONVST signal starts the conversion. Data outputs are inCODE–4–3C O U N T20060080010002318001859 F05400–2–1014120014001600。
0908580021;中文规格书,Datasheet资料
This document was generated on 05/20/2011PLEASE CHECK FOR LATEST PART INFORMATIONPart Number:0908580021Status:ActiveOverview:rast_5_connector_systemDescription:5.00mm (.197") Pitch Appli-Mate RAST 5 Header, Vertical, 2 Circuits, Reference K16Documents:3D ModelPackaging Specification PK-90833-001 (PDF)Drawing (PDF)Packaging Specification PK-90858-001 (PDF)Product Specification PS-99020-0037 (PDF)RoHS Certificate of Compliance (PDF)Agency CertificationCSA LR19980ULE29179GeneralProduct Family PCB Headers Series90858Application Power, Wire-to-Board Overviewrast_5_connector_system Product NameRAST 5PhysicalBreakawayNo Circuits (Loaded)2Circuits (maximum)2Color - ResinNatural Durability (mating cycles max)10First Mate / Last Break No Flammability94V-0Glow-Wire Compliant No Guide to Mating Part No Keying to Mating Part None Lock to Mating Part None Material - MetalBrass Material - Plating MatingTin Material - Plating Termination Tin Number of Rows 1Orientation VerticalPC Tail Length 3.50mm (.138")PCB Locator Yes PCB RetentionNonePCB Thickness - Recommended 1.40mm (.055")Packaging TypeBagPitch - Mating Interface 5.00mm (.197")Polarized to PCB Yes Shrouded Fully StackableYes Surface Mount Compatible (SMC)NoTemperature Range - Operating -20°C to +85°C Termination Interface: StyleThrough Hole ElectricalCurrent - Maximum per Contact 16A Voltage - Maximum250VMaterial InfoSeriesimage - Reference onlyEU RoHSChina RoHSELV and RoHS Compliant REACH SVHCContains SVHC: No Low-Halogen Status Not Low-HalogenNeed more information on product environmental compliance?Email productcompliance@For a multiple part number RoHS Certificate of Compliance, click herePlease visit the Contact Us section for any non-product compliance questions.Search Parts in this Series 90858SeriesMates WithAppli-Mate 5.0 IDT Connector System Female Receptacle 90835 , 90833Reference - Drawing NumbersPackaging Specification PK-90833-001, PK-90858-001Product Specification PS-99020-0037Sales Drawing SD-90858-001This document was generated on 05/20/2011PLEASE CHECK FOR LATEST PART INFORMATION分销商库存信息: MOLEX 0908580021。
1823859中文资料
Extract from the onlinecatalogICC 2,5/ 3-STZ-5,08Order No.: 1823859The illustration shows a 15-position versionhttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1823859Plug component, nominal current: 12 A, rated voltage: 250 V, pitch:5.08 mm, no. of positions: 3, type of connection: Crimp connectionhttp://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsPitch 5.08 mmNumber of positions3Technical dataInsulating material group IRated surge voltage (III/3) 4 kVRated surge voltage (III/2) 4 kVRated surge voltage (II/2) 4 kVRated voltage (III/2)320 VRated voltage (II/2)630 VConnection in acc. with standard EN-VDENominal current I N12 ANominal voltage U N250 VNominal cross section 2.5 mm2Maximum load current12 AInsulating material PAInflammability class acc. to UL 94V0Connection dataConductor cross section stranded min.0.5 mm2Conductor cross section stranded max. 2.5 mm2Conductor cross section AWG/kcmil min.20Conductor cross section AWG/kcmil max14Certificates / ApprovalsApproval logoCSANominal voltage U N300 VNominal current I N10 AAWG/kcmil20-14CULNominal voltage U N300 VNominal current I N10 AAWG/kcmil20-14ULNominal voltage U N300 VNominal current I N10 AAWG/kcmil20-14Certification CB, CSA, CUL, UL, VDE-PZIAccessoriesItem Designation DescriptionMarking0804280SK 5,08/2,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 10-section markerstrip, 14 identical decades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for 140 terminal blocksPlug/Adapter3190577ICC-MT 0,5-1,0Module male contact, is inserted into the ICC connector shell afterthe conductor has been crimped, for conductors from 0.5-1.0 mm²3190603ICC-MT 0,5-1,0 BA Module male contact, is inserted into the ICC connector shell afterthe conductor has been crimped, for conductors from 0.5-1.0 mm²,ribbon contact3190580ICC-MT 1,5-2,5Module male contact, is inserted into the ICC connector shell afterthe conductor has been crimped, for conductors from 1.5-2.5 mm²3190593ICC-MT 1,5-2,5 BA Module male contact, is inserted into the ICC connector shell afterthe conductor has been crimped, for conductors from 1.5-2.5 mm²,ribbon contact1810529STZ 2-MSTBC-5,08Strain relief for snapping into the latching chambers of the plugcomponents, 2-pos., labeling with ZB 61810532STZ 4-MSTBC-5,08Strain relief for snapping into the latching chambers of the plugcomponents, 4-pos., labeling with ZB 61810516STZ 8-MSTBC-5,08Strain relief for snapping into the latching chambers of the plugcomponents, 8-pos., labeling with ZB 61810503STZ 12-MSTBC-5,08Strain relief for snapping into the latching chambers of the plugcomponents, 12-pos., labeling with ZB 6Tools1204038CRIMPFOX MT 2,5Crimping pliers, for crimping conductors to the module femalecontacts STG-MTN, crimp range: 0.5-2.5 mm², AWG: 20-14 1205037SZS 0,4X2,5Screwdriver, bladed, matches all screw terminal blocks up to 1.5mm² connection cross section, blade: 0.4 x 2.5 mmAdditional productsItem Designation DescriptionGeneral1872703A-ICV 2,5/ 3-G-5,08Header, nominal current: 12 A, rated voltage: 250 V, pitch: 5.08mm, no. of positions: 3, mounting: Mounting rail1873061FKC 2,5/ 3-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Spring-cage connection1902123FKCT 2,5/ 3-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Spring-cage connection1873964FKCVR 2,5/ 3-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Spring-cage connection1873663FKCVW 2,5/ 3-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Spring-cage connection1777293FRONT-MSTB 2,5/ 3-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Screwconnection1786417IC 2,5/ 3-G-5,08Header, nominal current: 12 A, rated voltage: 320 V, pitch: 5.08mm, number of positions: 3, mounting type: soldering 1785955ICV 2,5/ 3-G-5,08Header, nominal current: 12 A, rated voltage: 320 V, pitch: 5.08mm, number of positions: 3, mounting type: soldering 1757022MSTB 2,5/ 3-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Screwconnection1776168MSTB 2,5/ 3-STZ-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Screwconnection1808829MSTBC 2,5/ 3-ST-5,08Plug component, nominal current: 12 A, rated voltage: 320 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Crimpconnection1809514MSTBC 2,5/ 3-STZ-5,08Plug component, nominal current: 12 A, rated voltage: 320 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Crimpconnection1809051MSTBC 2,5/ 3-STZ-5,08-R Plug component, nominal current: 12 A, rated voltage: 320 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Crimpconnection1769023MSTBP 2,5/ 3-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Screwconnection1779990MSTBT 2,5/ 3-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Screwconnection1824133MSTBU 2,5/ 3-STD-5,08Plug component, nominal current: 12 A, rated voltage: 320 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Screwconnection1792252MVSTBR 2,5/ 3-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Screwconnection1792760MVSTBW 2,5/ 3-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Screwconnection1917914QC 0,75/ 3-ST-5,08Plug components, 5.08 mm pitch, color: green, no. of positions 3,dimension a 10.16 mm1883268QC 1/ 3-ST-5,08Plug, nominal current: 10 A, rated voltage: 500 V, pitch: 5.08mm, number of positions: 3, connection method: Insulationdisplacement connection QUICKON1826296SMSTB 2,5/ 3-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Screwconnection1853023TMSTBP 2,5/ 3-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 3, type of connection: Screwconnection1873029ZFKK 1,5-ICV-5,08Modular terminal blocks with plug entry, cross section: 0.2 - 1.5mm², width: 5.1 mm, color: grayDrawingsDimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。
LTC1851CFW#PBF;LTC1850CFW#PBF;LTC1850CFW;LTC1850CFW#TR;LTC1850CFW#TRPBF;中文规格书,Datasheet资料
25603072358440960512102415362048CODELTC1850/51 G011/218501fA UG WA W UW A R BSOLUTEXI TI SSupply Voltage (V DD ).................................................6V Analog Input Voltage (Note 3).....–0.3V to (V DD + 0.3V)Digital Input Voltage (Note 4)....................–0.3V to 10V Digital Output Voltage..................–0.3V to (V DD + 0.3V)Power Dissipation..............................................500mWWUUPACKAGE/ORDER I FOR ATIOOV DD = V DD (Notes 1, 2)Ambient Operating Temperature RangeLTC1850C/LTC1851C............................ 0°C to 70°C LTC1850I/LTC1851I.......................... –40°C to 85°C Storage Temperature Range.................–65°C to 150°C Lead Temperature (Soldering, 10 sec)................ 300°CConsult LTC Marketing for parts specified with wider operating temperature ranges./318501fSYMBOL PARAMETERCONDITIONS MIN TYP MAX UNITSV INAnalog Input Range (Note 9)4.75V ≤ V DD ≤5.25VUnipolar, Gain = 1 (PGA = 1)0 – REFCOMP V Unipolar, Gain = 2 (PGA = 0)0 – REFCOMP/2V Bipolar, Gain = 1 (PGA = 1)±REFCOMP/2V Bipolar, Gain = 2 (PGA = 0)±REFCOMP/4VI IN Analog Input Leakage Current V IN > 0V < V DD , All Channels q±1µA C INAnalog Input CapacitanceBetween Conversions (Gain = 1)15pF Between Conversions (Gain = 2)25pF During Conversions5pF t ACQ Sample-and-Hold Acquisition Time q 50150ns t S(MUX)Multiplexer Settling Time (Includes t ACQ )q 50150ns t AP Sample-and-Hold Aperture Delay Time –0.5ns t jitter Sample-and-Hold Aperture Delay Time Jitter 2ps RMSCMRRAnalog Input Common Mode Rejection Ratio0V < (A IN – = A IN +) < 5V60dBThe q denotes the specifications which apply over the full operating temperature range, otherwisespecifications are at T A = 25°C. (Note 5)A ALOG I PUT UULTC1850LTC1851PARAMETERCONDITIONSMIN TYP MAX MIN TYP MAXUNITS Resolution (No Missing Codes)q 1012Bits Integral Linearity Error (Note 7)q ±0.25±0.5±0.35±1LSB Differential Linearity Error q±0.25±0.5±0.25±1LSB Offset Error (Bipolar and Unipolar)(Note 8)Gain = 1 (PGA = 1)REFCOMP ≥ 2V ±2±5LSB Gain = 1 (PGA = 1)REFCOMP ≥ 2V q ±0.5±2±1±7LSB Gain = 2 (PGA = 0)q ±1±4±2±10LSB Offset Error Match ±0.5±1LSB Unipolar Gain Error With External 4.096V Reference Gain = 1 (PGA = 1)Applied to REFCOMP (Note 12)±2±6LSB Gain = 2 (PGA = 0)±4±10LSB Unipolar Gain Error Match ±0.5±1LSB Bipolar Gain Error With External 4.096V Reference Gain = 1 (PGA = 1)Applied to REFCOMP (Note 12)±2±6LSB Gain = 2 (PGA = 0)±4±10LSB Bipolar Gain Error Match±0.5±1LSB Full-Scale Error Temperature Coefficient1515ppm/°CThe q denotes the specifications which apply over the full operatingtemperature range, otherwise specifications are at T A = 25°C. (Notes 5, 6)CO VERTER CHARACTERISTICSU/418501fSYMBOL PARAMETERCONDITIONS MIN TYP MAX UNITSV IH High Level Input Voltage V DD = 5.25V q 2.4V V IL Low Level Input Voltage V DD = 4.75V q 0.8V I IN Digital Input Current V IN = 0V to V DDq±5µA C IN Digital Input Capacitance 2pF V OH High Level Output Voltage V DD = 4.75V, I O = –10µA 4.5VV DD = 4.75V, I O = –200µA q 4.0VV OL Low Level Output VoltageV DD = 4.75V, I O = 160µA 0.05V V DD = 4.75V, I O = 1.6mA q 0.100.4V I OZ Hi-Z Output Leakage D11 to D0, AD OUT , A1OUT , A2OUT , DIFF OUT V OUT = 0V to V DD , CS High q ±10µA C OZ Hi-Z Capacitance D11 to D0, AD OUT , A1OUT , A2OUT , DIFF OUT CS High (Note 9)q15pF I SOURCE Output Source Current V OUT = 0V –20mA I SINKOutput Sink CurrentV OUT = V DD30mAThe q denotes the specifications which apply over thefull operating temperature range, otherwise specifications are at T A = 25°C. (Note 5)DIGITAL I PUTS A D DIGITAL OUTPUTSUU PARAMETERCONDITIONS MIN TYP MAX UNITSREFOUT Output VoltageI OUT = 0 2.482.50 2.52V REFOUT Output Temperature Coefficient I OUT = 0±15ppm/°C REFOUT Line Regulation 0.01LSB/V Reference Buffer Gain V REFCOMP /V REFIN 1.636 1.638 1.640V/V REFCOMP Output Voltage External 2.5V Reference 4.090 4.096 4.100V Internal 2.5V Reference 4.0604.096 4.132V REFCOMP ImpedanceREFIN = V DD6.4k ΩT A = 25°C. (Notes 5, 6)I TER AL REFERE CE U U ULTC1850LTC1851SYMBOL PARAMETER CONDITIONS MIN TYP MAXMIN TYP MAXUNITSSNRSignal-to-Noise Ratio 47kHz Input SignalUnipolar, PGA = 061.671dB Unipolar, PGA = 161.772dB Bipolar, PGA = 061.671dB Bipolar, PGA = 161.772dBS/(N+D)Signal-to-(Noise + Distortion) Ratio 47kHz Input SignalUnipolar, PGA = 061.070dB Unipolar, PGA = 161.071dB Bipolar, PGA = 061.071dB Bipolar, PGA = 161.272dB THDTotal Harmonic Distortion 47kHz Input Signal,Unipolar, PGA = 0First 5 Harmonics–76–80dB Unipolar, PGA = 1–78–82dB Bipolar, PGA = 0–81–87dB Bipolar, PGA = 1–80–86dB SFDRSpurious-Free Dynamic Range 47kHz Input SignalUnipolar, PGA = 07482dB Unipolar, PGA = 18086dB Bipolar, PGA = 08490dB Bipolar, PGA = 18288dBDY A IC ACCURACYUW (Note 5)/518501fSYMBOL PARAMETERCONDITIONSMIN TYP MAX UNITS f SAMPLE(MAX)Maximum Sampling Frequency q 1.25MHz Acquisition + Conversion q 800ns t CONV Conversion Time q 650ns t ACQ Acquisition Time q150ns t 1CS to RD Setup Time (Notes 9, 10)q 0ns t 2CS to CONVST Setup Time (Notes 9, 10)q10nst 3CS to SHDN Setup Time (Notes 9, 10)200ns t 4SHDN to CONVST Wake-Up TimeNap Mode (Note 10)200ns Sleep Mode, 10µF REFCOMP 10ms Bypass Capacitor (Note 10)t 5CONVST Low Time (Notes 10, 11)q 50nst 6CONVST to BUSY Delay C L = 25pF10ns q 60ns t 7Data Ready Before BUSY2035ns q15ns t 8Delay Between Conversions (Note 10)q 50ns t 9Wait Time RD After BUSY q –5ns t 10Data Access Time After RDC L = 25pF2035ns q45ns C L = 100pF2545ns q60ns t 11BUS Relinquish Time1030ns 0°C to 70°C q 35ns –40°C to 85°Cq 40ns t 12RD Low Time qt 10ns t 13CONVST High Time (Note 10)q 50ns t 14Latch Setup Time (Notes 9, 10)q 10ns t 15Latch Hold Time (Notes 9, 10)q 10ns t 16WR Low Time(Note 10)q50nsThe q denotes the specifications which apply over the full operating temperaturerange, otherwise specifications are at T A = 25°C. (Note 5)TI I G CHARACTERISTICSUW The q denotes the specifications which apply over the full operating temperaturerange, otherwise specifications are at T A = 25°C. (Note 5)POWER REQUIRE E T SWU SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITSV DD Positive Supply Voltage (Note 10)q 4.75 5.25V OV DD Output Positive Supply Voltage (Note 10)q 2.75.25V I DD Positive Supply Current V DD = V DD = OV DD = 5V,q 810mA f SAMPLE = 1.25MHzP DISSPower Dissipationq4050mW Power Down Positive Supply CurrentNap Mode SHDN = 0V, CS = 0V 1mA Sleep ModeSHDN = 0V, CS = 5V 50µA Power Down Power Dissipation Nap Mode SHDN = 0V, CS = 0V 5mW Sleep ModeSHDN = 0V, CS = 5V0.25mW/618501fSYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITSt 17WR High Time (Note 10)q 50ns t 18M1 to M0 Setup Time (Notes 9, 10)q10nst 19M0 to BUSY DelayM1 High 20ns t 20M0 to WR (or RD) Setup Time (Notes 9, 10)q t 19ns t 21M0 High Pulse Width(Note 10)q 50ns t 22RD High Time Between Readback Reads (Note 10)q 50ns t 23Last WR (or RD) to M0(Note 10)q 10ns t 24M0 to RD Setup Time (Notes 9, 10)q t 19ns t 25M0 to CONVST (Note 10)q t 19ns t 26Aperture Delay –0.5ns t 27Aperture Jitter2ps RMSNote 1: Absolute maximum ratings are those values beyond which the life of a device may be impaired.Note 2: All voltage values are with respect to ground with GND, OGND and GND wired together unless otherwise noted.Note 3: When these pin voltages are taken below ground or above V DD ,they will be clamped by internal diodes. This product can handle input currents of 100mA below ground or above V DD without latchup.Note 4: When these pin voltages are taken below ground, they will be clamped by internal diodes. This product can handle input currents of 100mA below ground without latchup. These pins are not clamped to V DD .Note 5: V DD = 4.75V to 5.25V, f SAMPLE = 1.25MHz, t r = t f = 2ns unless otherwise specified.Note 6: Linearity, offset and full-scale specifications apply for a single-ended input on any channel with COM grounded.Note 7: Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual end points of the transfer curve.The deviation is measured from the center of the quantization band.Note 8: Bipolar offset is the offset voltage measured from –0.5LSB when the output code flickers between 0111 1111 1111 and 1000 0000 0000 for LTC1851 and between 01 1111 1111 and 10 0000 0000 for LTC1850.Note 9: Guaranteed by design, not subject to test.Note 10: Recommended operating conditions.Note 11: The falling CONVST edge starts a conversion. If CONVST returns high at a critical point during the conversion it can create small errors. For the best results, ensure that CONVST returns high either within 400ns Note 12: The analog input range is determined by the voltage onREFCOMP. The gain error specification is tested with an external 4.096V but is valid for any value of REFCOMP.The q denotes the specifications which apply over the full operating temperaturerange, otherwise specifications are at T A = 25°C. (Note 5)TI I G CHARACTERISTICSUW /7CODELTC1850/51 G04FREQUENCY (kHz)0100200300400LTC1850/51 G05500600SNR = 71.35dB SFDR = 90.4dB SINAD = 71.2dBFREQUENCY (kHz)0100200300400LTC1850/51 G06500600SNR = 72.3dB SFDR = 87.3dB SINAD = 71.4dBNonaveraged 4096 Point FFT,f IN = 47kHz, Bipolar Mode,PGA = 0, LTC1851Nonaveraged 4096 Point FFT,f IN = 47kHz, Unipolar Mode,PGA = 1, LTC1851CODE512102415362048LTC1850/51 G012560307235844096LTC1850/51 G02FREQUENCY (kHz)100200300400LTC1850/51 G03500600SNR = 71.2dB SFDR = 82.0dB SINAD = 70.6dBNonaveraged 4096 Point FFT,f IN = 47kHz, Unipolar Mode,PGA = 0, LTC1851CODE512102415362048LTC1850/51 G072560307235844096FREQUENCY (kHz)0–120A M P L I T U D E (dB )–100–80–60–400100200300400LTC1850/51 G08500600–20SNR = 72.3dB SFDR = 89.3dB SINAD = 72.1dBTypical INL, PGA = 0, LTC1851Nonaveraged 4096 Point FFT,f IN = 47kHz, Bipolar Mode,PGA = 1, LTC1851/818501fTYPICAL PERFOR A CE CHARACTERISTICSU WFREQUENCY (kHz)10–100D I S T O R T I O N (d B )–90–85–80–75–70–651001000185051 G10–60–55–50–9510000FREQUENCY (Hz)1kC M R R (d B )40506010MLTC1850/51 G113020010k100k 1M 108070Distortion vs Input Frequency,Bipolar Mode, PGA = 0Input Common Mode Rejection Ratio vs Frequency, Bipolar Mode,PGA = 0FREQUENCY (Hz)1kC M R R (d B )40506010MLTC1850/51 G143020010k100k 1M 108070Input Common Mode RejectionRatio vs Frequency, Unipolar Mode,PGA = 0Input Common Mode Rejection Ratio vs Frequency, Bipolar Mode,PGA = 1FREQUENCY (Hz)1k C MR R (d B )40506010MLTC1850/51 G133020010k 100k 1M 108070FREQUENCY (kHz)10–100D I S T O R T I O N (d B )–90–85–80–75–70–651001000185051 G09–60–55–50–9510000Distortion vs Input Frequency,Bipolar Mode, PGA = 1FREQUENCY (kHz)10–100D I S T O R T I O N (d B )–90–85–80–75–70–651001000185051 G19–60–55–50–9510000FREQUENCY (kHz)10–100D I S T O R T I O N (d B )–90–85–80–75–70–651001000185051 G20–60–55–50–9510000Distortion vs Input Frequency,Unipolar Mode, PGA = 0Distortion vs Input Frequency,Unipolar Mode, PGA = 1FREQUENCY (Hz)1k C M R R (d B )40506010MLTC1850/51 G163020010k 100k 1M 108070Input Common Mode Rejection Ratio vs Frequency, Unipolar Mode,PGA = 1/9/1018501fU U UPI FU CTIO SCH0 to CH7 (Pins 1 to 8): Analog Input Pins. Input pins can be used single ended relative to the analog input common pin (COM) or differentially in pairs (CH0 and CH1, CH2 and CH3, CH4 and CH5, CH6 and CH7).COM (Pin 9): Analog Input Common Pin. For single-ended operation (DIFF = 0), COM is the “–” analog input. COM is disabled when DIFF is high.REFOUT (Pin 10): Internal 2.5V Reference Output. Re-quires bypass to analog ground plane with 1µF.REFIN (Pin 11): Reference Mode Select/Reference Buffer Input. REFIN selects the Reference mode and acts as the reference buffer Input. REFIN tied to ground will produce 2.048V on the REFCOMP pin. REFIN tied to the positive supply disables the reference buffer to allow REFCOMP to be driven externally. For voltages between 1V and 2.6V,the reference buffer produces an output voltage on the REFCOMP pin equal to 1.6384 times the voltage on REFIN (4.096V on REFCOMP for a 2.5V input on REFIN).REFCOMP (Pin 12): Reference Buffer Output. REFCOMP sets the full-scale input span. The reference buffer pro-duces an output voltage on the REFCOMP pin equal to 1.6384 times the voltage on the REFIN pin (4.096V on REFCOMP for a 2.5V input on REFIN). REFIN tied to ground will produce 2.048V on the REFCOMP pin.REFCOMP can be driven externally if REFIN is tied to the positive supply. Requires bypass to analog ground plane with 10µF tantalum in parallel with 0.1µF ceramic or 10µF ceramic.GND (Pin 13): Ground. Tie to analog ground plane.V DD (Pin 14): 5V Supply. Short to Pin 15.V DD (Pin 15): 5V Supply. Bypass to GND with 10µF tantalum in parallel with 0.1µF ceramic or 10µF ceramic.GND (Pin 16): Ground for Internal Logic. Tie to analog ground plane.DIFF OUT /S6 (Pin 17): Three-State Digital Data Output.Active when RD is low. Following a conversion, the single-ended/differential bit of the present conversion is available on this pin concurrent with the conversion result. In Readback mode, the single-ended/differential bit of thecurrent sequencer location (S6) is available on this pin.The output swings between OV DD and OGND.A2OUT /S5, A1OUT /S4, A0OUT /S3 (Pins 18 to 20): Three-State Digital MUX Address Outputs. Active when RD is low. Following a conversion, the MUX address of the present conversion is available on these pins concurrent with the conversion result. In Readback mode, the MUX address of the current sequencer location (S5-S3) is available on these pins. The outputs swing between OV DD and OGND.D9/S2 (Pin 21, LTC1850): Three-State Digital Data Out-put. Active when RD is low. Following a conversion, bit 9of the present conversion is available on this pin. In Readback mode, the unipolar/bipolar bit of the current sequencer location (S2) is available on this pin. The output swings between OV DD and OGND.D11/S2 (Pin 21, LTC1851): Three-State Digital Data Out-put. Active when RD is low. Following a conversion, bit 11of the present conversion is available on this pin. In Readback mode, the unipolar/bipolar bit of the current sequencer location (S2) is available on this pin. The output swings between OV DD and OGND.D8/S1 (Pin 22, LTC1850): Three-State Digital Data Out-puts. Active when RD is low. Following a conversion, bit 8of the present conversion is available on this pin. In Readback mode, the gain bit of the current sequencer location (S1) is available on this pin. The output swings between OV DD and OGND.D10/S1 (Pin 22, LTC1851): Three-State Digital Data Out-puts. Active when RD is low. Following a conversion, bit 10of the present conversion is available on this pin. In Readback mode, the gain bit of the current sequencer location (S1) is available on this pin. The output swings between OV DD and OGND.D7/S0 (Pin 23, LTC1850): Three-State Digital Data Out-puts. Active when RD is low. Following a conversion, bit 7of the present conversion is available on this pin. In Readback mode, the end of sequence bit of the current sequencer location (S0) is available on this pin. The output swings between OV DD and OGND./分销商库存信息:LINEAR-TECHNOLOGYLTC1851CFW#PBF LTC1850CFW#PBF LTC1850CFWLTC1850CFW#TR LTC1850CFW#TRPBF LTC1850IFW#PBF LTC1850IFW LTC1850IFW#TR LTC1850IFW#TRPBF LTC1851CFW#TR LTC1851CFW#TRPBF LTC1851IFWLTC1851IFW#PBF LTC1851IFW#TR LTC1851IFW#TRPBF LTC1851CFW。
1829345中文资料
Extract from the onlinecatalogDFK-MC 1,5/ 2-GF-3,81Order No.: 1829345The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1829345Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81 mm, no. of positions: 2, mounting: Direct mountinghttp://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsPitch 3.81 mmDimension a 3.81 mmNumber of positions2Technical dataInsulating material group IRated surge voltage (III/3) 2.5 kV Rated surge voltage (III/2) 2.5 kV Rated surge voltage (II/2) 2.5 kV Rated voltage (III/2)160 V Rated voltage (II/2)320 V Connection in acc. with standard EN-VDE Nominal current I N8 A Nominal voltage U N160 V Nominal cross section 1.5 mm2 Maximum load current8 A Insulating material PA Inflammability class acc. to UL 94V0Max. current slip-on connection8 A Dimensions of slip-on connection 2.8 x 0.8 mmConnection dataConductor cross section solid min.0.14 mm2 Conductor cross section solid max. 1.5 mm2 Conductor cross section stranded min.0.14 mm2 Conductor cross section stranded max. 1.5 mm2 Conductor cross section AWG/kcmil min.28 Conductor cross section AWG/kcmil max16 Certificates / ApprovalsCSANominal voltage U N150 V Nominal current I N8 ACULNominal voltage U N300 V Nominal current I N8 AULNominal voltage U N300 VNominal current I N8 ACertification CB, CSA, CUL, GOST, UL, VDE-PZIAccessoriesItem Designation DescriptionAssembly0710015DFK-MC SS Screw set, for securing the header to the housing wall, consists ofM2 x 8 screw, spring washer and nut, 1 piece eachMarking0804109SK 3,81/2,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 10-section markerstrip, 14 identical decades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for 140 terminal blocksPlug/Adapter1734634CP-MSTB Coding profile, is inserted into the slot on the plug or invertedheader, red insulating materialTools1205037SZS 0,4X2,5Screwdriver, bladed, matches all screw terminal blocks up to 1.5mm² connection cross section, blade: 0.4 x 2.5 mmAdditional productsItem Designation DescriptionGeneral1851232FK-MCP 1,5/ 2-STF-3,81Plug, with screw flange, nominal current: 8 A, rated voltage: 160V, pitch: 3.81 mm, no. of positions: 2, type of connection: Spring-cage connection1850851FRONT-MC 1,5/ 2-STF-3,81Plug component, nominal current: 8 A, rated voltage: 160 V, pitch:3.81 mm, no. of positions: 2, type of connection: Screw connection 1827703MC 1,5/ 2-STF-3,81Plug component, nominal current: 8 A, rated voltage: 160 V, pitch:3.81 mm, no. of positions: 2, type of connection: Screw connection 1852367MCC 1/ 2-STZF-3,81Plug component, nominal current: 8 A, rated voltage: 160 V, pitch:3.81 mm, no. of positions: 2, type of connection: Crimp connection 1828346MCVR 1,5/ 2-STF-3,81Plug component, nominal current: 8 A, rated voltage: 160 V, pitch:3.81 mm, no. of positions: 2, type of connection: Screw connection 1828498MCVW 1,5/ 2-STF-3,81Plug component, nominal current: 8 A, rated voltage: 160 V, pitch:3.81 mm, no. of positions: 2, type of connection: Screw connection1897542QC 0,5/ 2-STF-3,81Plug, nominal current: 6 A, rated voltage: 320 V, pitch: 3.81mm, number of positions: 2, connection method: Insulationdisplacement connection QUICKONDrawingsDrilling diagramDimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。
1859658资料
Extract from the onlinecatalogEMSTBVA 2,5/16-G-5,08Order No.: 1859658The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1859658Header, nominal current: 12 A, rated voltage: 200 V, pitch: 5.08 mm, no. of positions: 16, mounting: press inhttp://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsPitch 5.08 mmDimension a76.2 mmNumber of positions16Pin dimensions1,7 mmHole diameter 1.75 mmTechnical dataInsulating material group IIIaRated surge voltage (III/3) 4 kVRated surge voltage (III/2) 4 kVRated surge voltage (II/2) 4 kVRated voltage (III/2)320 VRated voltage (II/2)320 VConnection in acc. with standard EN-VDENominal current I N12 ANominal voltage U N200 VMaximum load current12 AInsulating material PBTInflammability class acc. to UL 94V0Certificates / ApprovalsApproval logoCULNominal voltage U N300 VNominal current I N10 AULNominal voltage U N300 VNominal current I N10 ACertification CB, CUL, GOST, UL, VDE-PZIAccessoriesItem Designation DescriptionAssembly1877203EMSTB 2,5-SH Stamp holder, for upper and lower stamp1877229EMSTBVA 2,5-SS-2-5,08Stamp set, consisting of an upper and lower stamp, upper stamp:17 to 24-pos., lower stamp: 2 to 24-pos., pitch: 5.08 mm 1755477MSTB-BL Keying cap, for forming sections, plugs onto header pin, greeninsulating materialMarking0804293SK 5,08/3,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 12 identicaldecades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for120 terminal blocksPlug/Adapter1734401CR-MSTB Coding section, inserted into the recess in the header or theinverted plug, red insulating materialAdditional productsItem Designation DescriptionGeneral1873197FKC 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Spring-cage connection1902259FKCT 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Spring-cage connection1874099FKCVR 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Spring-cage connection1873799FKCVW 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Spring-cage connection1777426FRONT-MSTB 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Screwconnection1786543IC 2,5/16-G-5,08Header, nominal current: 12 A, rated voltage: 320 V, pitch: 5.08mm, number of positions: 16, mounting type: soldering 1786080ICV 2,5/16-G-5,08Header, nominal current: 12 A, rated voltage: 320 V, pitch: 5.08mm, number of positions: 16, mounting type: soldering 1757158MSTB 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Screwconnection1764248MSTB 2,5/16-STZ-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Screwconnection1808955MSTBC 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 320 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Crimpconnection1809640MSTBC 2,5/16-STZ-5,08Plug component, nominal current: 12 A, rated voltage: 320 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Crimpconnection1769159MSTBP 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Screwconnection1781124MSTBT 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Screwconnection1824269MSTBU 2,5/16-STD-5,08Plug component, nominal current: 12 A, rated voltage: 320 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Screwconnection1831456MSTBVK 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 320 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Screwconnection1792388MVSTBR 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Screwconnection1792896MVSTBW 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Screwconnection1918052QC 0,75/16-ST-5,08Plug components, 5.08 mm pitch, color: green, no. of positions 16,dimension a 76.20 mm1883844QC 1/16-ST-5,08Plug, nominal current: 10 A, rated voltage: 500 V, pitch: 5.08mm, number of positions: 16, connection method: Insulationdisplacement connection QUICKON1826429SMSTB 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 250 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Screwconnection1833959UMSTBVK 2,5/16-ST-5,08Plug component, nominal current: 12 A, rated voltage: 320 V,pitch: 5.08 mm, no. of positions: 16, type of connection: Screwconnection1873029ZFKK 1,5-ICV-5,08Modular terminal blocks with plug entry, cross section: 0.2 - 1.5mm², width: 5.1 mm, color: grayDrawingsDrilling diagramDimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。
1953981资料
Extract from the onlinecatalogMCDN 1,5/ 9-G1-3,5 P14THROrder No.: 1953981The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1953981Headers, 3.5 mm pitch, pin length 1,4 mm, plug-in direction parallel to the PCBhttp://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsLength13.3 mmHeight15.2 mmPitch 3.5 mmDimension a28 mmNumber of positions9Pin dimensions0,8 x 0,8 mm Pin spacing 3.5 mmHole diameter 1.4 mmTechnical dataInsulating material group IIIaRated surge voltage (III/3) 2.5 kVRated surge voltage (III/2) 2.5 kVRated surge voltage (II/2) 2.5 kVRated voltage (III/2)160 VRated voltage (II/2)250 V Connection in acc. with standard EN-VDE Nominal current I N8 ANominal voltage U N160 V Maximum load current8 A (per position) Insulating material LCP Inflammability class acc. to UL 94V0Certificates / ApprovalsApproval logoCULNominal voltage U N150 VNominal current I N8 AULNominal voltage U N150 VNominal current I N8 A Certification CUL, ULAccessoriesItem Designation DescriptionMarking0805030SK 3,5/2,8:SO Marker card, special printing, self-adhesive, labeled acc. tocustomer requirements, 14 identical marker strips per card, max.25-position labeling per strip, color: White0804109SK 3,81/2,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 10-section markerstrip, 14 identical decades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for 140 terminal blocksPlug/Adapter1734634CP-MSTB Coding profile, is inserted into the slot on the plug or invertedheader, red insulating materialDrawingsDrilling diagram*) ≤ 8-pos. = 1.3 / > 8-pos. = 1.4Dimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。
180918资料
180918 Product DetailsHome | Customer Support | Suppliers | Site Map | Privacy Policy | Browser Support© 2008 Tyco Electronics Corporation All Rights Reserved SearchProducts Documentation Resources My Account Customer SupportHome > Products > By Type > FASTON Electrical Quick Connects > Product Feature Selector > Product Details180918Active Multiple Circuit Housings with Tabs &Receptacles Including FASTIN-FASTONAlways EU RoHS/ELV Compliant (Statement of Compliance)Product Highlights:?Receptacle Housing?Number of Circuits = 2?Tab Fit = 6.35 mm?Loose Piece?Color = NaturalView all Features | Find SimilarProductsCheck Pricing &AvailabilitySearch for ToolingProduct FeatureSelectorContact Us AboutThis ProductQuick LinksDocumentation & Additional InformationProduct Drawings:? 2 WAY FLAG FASTIN ON REC. HOUS.(PDF, English)Catalog Pages/Data Sheets:?Automachine and General Products(PDF, English)Product Specifications:?FASTIN-FASTON CONN. .110 INCH, .187 INCH, .250 INCH,...(PDF, Italian)Application Specifications:?None AvailableInstruction Sheets:?None AvailableCAD Files:?None AvailableList all Documents Additional Information:?Product Line InformationRelated Products:?ToolingProduct Features (Please use the Product Drawing for all design activity)Product Type Features:?Product Type = Receptacle Housing ?Number of Circuits = 2?Tab Fit (mm [in]) = 6.35 [.250]?Color = Natural?FASTON = YesHousing Related Features:?Housing Material = Polyamide Industry Standards:?RoHS/ELV Compliance = RoHS compliant, ELVcompliant?Lead Free Solder Processes = Not relevant forlead free process?RoHS/ELV Compliance History = Always wasRoHS compliantPackaging Related Features:?Packaging Method = Loose PieceOther:?Line = FASTIN-FASTON .250?Brand = AMPProvide Website Feedback | Contact Customer Support。
1900853资料
Extract from the onlinecatalogMC 1,5/ 3-ST1F-5,08Order No.: 1900895The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1900895Plug component, nominal current: 8 A, rated voltage: 250 V, pitch: 5.08 mm, no. of positions: 3, type of connection: Screw connectionhttp://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsPitch 5.08 mmDimension a45.72 mmNumber of positions10Screw thread M 2Tightening torque, min0.22 NmTechnical dataInsulating material group IRated surge voltage (III/3) 4 kVRated surge voltage (III/2) 4 kVRated surge voltage (II/2) 4 kVRated voltage (III/2)320 VRated voltage (II/2)630 VConnection in acc. with standard EN-VDENominal current I N8 ANominal voltage U N250 VNominal cross section 1.5 mm2Maximum load current8 A (with 1.5 mm2 conductor cross section) Insulating material PAInflammability class acc. to UL 94V0Internal cylindrical gage A1Stripping length7 mmConnection dataConductor cross section solid min.0.14 mm2Conductor cross section solid max. 1.5 mm2Conductor cross section stranded min.0.14 mm2Conductor cross section stranded max. 1.5 mm2Conductor cross section stranded, with ferrule0.25 mm2without plastic sleeve min.Conductor cross section stranded, with ferrule1.5 mm2without plastic sleeve max.Conductor cross section stranded, with ferrule0.25 mm2with plastic sleeve min.Conductor cross section stranded, with ferrule0.5 mm2with plastic sleeve max.Conductor cross section AWG/kcmil min.28Conductor cross section AWG/kcmil max162 conductors with same cross section, solid min.0.08 mm22 conductors with same cross section, solid max.0.5 mm22 conductors with same cross section, stranded0.08 mm2min.2 conductors with same cross section, stranded max.0.75 mm 22 conductors with same cross section, stranded,ferrules without plastic sleeve, min.0.25 mm 22 conductors with same cross section, stranded,ferrules without plastic sleeve, max.0.34 mm 22 conductors with same cross section, stranded,TWIN ferrules with plastic sleeve, min.0.5 mm 22 conductors with same cross section, stranded,TWIN ferrules with plastic sleeve, max.0.5 mm2Certificates / ApprovalsApproval logoCULNominal voltage U N 300 V Nominal current I N 8 A AWG/kcmil 30-14ULNominal voltage U N 300 V Nominal current I N 8 A AWG/kcmil 30-14Certification CB, CUL, GOST, UL, VDE-PZIAccessories Item Designation DescriptionGeneral 1834343KGG-MC 1,5/ 2Cable housing, for cable diameters of up to 5 mm, cable ties and marker strips are included, color: green, no. of positions: 21834385KGG-MC 1,5/ 6Cable housing, for cable diameters of 4 - 11 mm, clamp, marker strips and transparent label carrier are included, color: green, no.of positions: 6Marking0804280SK 5,08/2,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 10-section markerstrip, 14 identical decades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for 140 terminal blocksTools1205037SZS 0,4X2,5Screwdriver, bladed, matches all screw terminal blocks up to 1.5mm² connection cross section, blade: 0.4 x 2.5 mmAdditional productsItem Designation DescriptionGeneral1836260MC 1,5/10-G-5,08Header, nominal current: 8 A, rated voltage: 250 V, pitch: 5.08mm, no. of positions: 10, mounting: Soldering1836370MCV 1,5/10-G-5,08Header, nominal current: 8 A, rated voltage: 250 V, pitch: 5.08mm, no. of positions: 10, mounting: SolderingDrawingsDimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Extract from the onlinecatalogFRONT-MC 1,5/ 2-STF-3,81Order No.: 1850851The figure shows a 10-position version of the producthttp://eshop.phoenixcontact.de/phoenix/treeViewClick.do?UID=1850851Plug component, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81 mm, no. of positions: 2, type of connection: Screw connectionhttp://Please note that the data givenhere has been taken from theonline catalog. For comprehensiveinformation and data, please referto the user documentation. TheGeneral Terms and Conditions ofUse apply to Internet downloads. Technical dataDimensions / positionsPitch 3.81 mmDimension a 3.81 mmNumber of positions2Screw thread M 2Tightening torque, min0.22 NmTechnical dataInsulating material group IRated surge voltage (III/3) 2.5 kVRated surge voltage (III/2) 2.5 kVRated surge voltage (II/2) 2.5 kVRated voltage (III/2)160 VRated voltage (II/2)320 VConnection in acc. with standard EN-VDENominal current I N8 ANominal voltage U N160 VNominal cross section 1.5 mm2Maximum load current8 A (with 1.5 mm2 conductor cross section) Insulating material PAInflammability class acc. to UL 94V0Internal cylindrical gage A1Stripping length9 mmConnection dataConductor cross section solid min.0.14 mm2Conductor cross section solid max. 1.5 mm2Conductor cross section stranded min.0.14 mm2Conductor cross section stranded max. 1.5 mm2Conductor cross section stranded, with ferrule0.25 mm2without plastic sleeve min.Conductor cross section stranded, with ferrule1.5 mm2without plastic sleeve max.Conductor cross section stranded, with ferrule0.25 mm2with plastic sleeve min.Conductor cross section stranded, with ferrule0.5 mm2with plastic sleeve max.Conductor cross section AWG/kcmil min.28Conductor cross section AWG/kcmil max162 conductors with same cross section, solid min.0.14 mm22 conductors with same cross section, solid max.0.5 mm22 conductors with same cross section, stranded0.14 mm2min.2 conductors with same cross section, stranded0.75 mm2max.2 conductors with same cross section, stranded,0.25 mm2ferrules without plastic sleeve, min.2 conductors with same cross section, stranded,0.34 mm2ferrules without plastic sleeve, max.2 conductors with same cross section, stranded,0.5 mm2TWIN ferrules with plastic sleeve, min.2 conductors with same cross section, stranded,0.5 mm2TWIN ferrules with plastic sleeve, max.Certificates / ApprovalsCSANominal voltage U N300 VNominal current I N8 AAWG/kcmil28-16CULNominal voltage U N300 VNominal current I N8 AAWG/kcmil30-16ULNominal voltage U N300 VNominal current I N8 AAWG/kcmil30-16Certification CB, CSA, CUL, UL, VDE-PZIAccessoriesItem Designation DescriptionMarking0804109SK 3,81/2,8:FORTL.ZAHLEN Marker card, printed horizontally, self-adhesive, 10-section markerstrip, 14 identical decades marked 1-10, 11-20 etc. up to 91-(99)100, sufficient for 140 terminal blocksTools1205037SZS 0,4X2,5Screwdriver, bladed, matches all screw terminal blocks up to 1.5mm² connection cross section, blade: 0.4 x 2.5 mmAdditional productsItem Designation DescriptionGeneral1829345DFK-MC 1,5/ 2-GF-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 2, mounting: Direct mounting1896941EMC 1,5/ 2-GF-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 2, mounting: Press in1879285EMCV 1,5/ 2-GF-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 2, mounting: Press in1858031IMC 1,5/ 2-STGF-3,81Plug component, nominal current: 8 A, rated voltage: 160 V, pitch:3.81 mm, no. of positions: 2, type of connection: Screw connection 1827868MC 1,5/ 2-GF-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 2, mounting: Soldering1908871MC 1,5/ 2-GF-3,81 THT Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 2, mounting: SMD/THT1842911MCD 1,5/ 2-G1F-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 2, mounting: Soldering1830101MCD 1,5/ 2-GF-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 2, mounting: Soldering1842762MCDV 1,5/ 2-G1F-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 2, mounting: Soldering1830253MCDV 1,5/ 2-GF-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 2, mounting: Soldering1830596MCV 1,5/ 2-GF-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 2, mounting: Soldering1833027MCVU 1,5/ 2-GFD-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 2, mounting: Direct mounting1827428SMC 1,5/ 2-GF-3,81Header, nominal current: 8 A, rated voltage: 160 V, pitch: 3.81mm, no. of positions: 2, mounting: SolderingDrawings Dimensioned drawingAddressPHOENIX CONTACT GmbH & Co. KGFlachsmarktstr. 832825 Blomberg,GermanyPhone +49 5235 3 00Fax +49 5235 3 41200http://www.phoenixcontact.de© 2008 Phoenix ContactTechnical modifications reserved;。