E16-01-D-T-A-A-A-A-1中文资料
ESA620电气安全分析仪商品说明书
Electrical Safety Analyzer• Superior compliance with multiple standards:IEC60601:2005, EN62353, VDE 751, ANSI/AAMI ES1:1993, NFPA-99, AN/NZS 3551, IEC61010 • Three test loads• Expanded leakage ranges through 10,000 µA • Dual-lead resistance, leakage, and voltage tests • AC only, dc only and true-rms leakage readings • 100 % and 110 % mains voltage for mains on applied part (lead isolation) test • 200 mA and 25 A ac PE test current• DSP filter technology for improved accuracy in leakage measurements • 20 A equipment current• More applied parts selections• ECG and performance waveforms • Intuitive user interface• Easy-to-use applied parts (ECG) connections • Insulation posts on applied parts connections • Five different insulation tests • Varying insulation test voltage500 V dc and 250 V dc• 2- or (optional) 4-wire ground wire resistance • Optional Ansur plug-in software • USB connection• CE, C-TICK and CSA for USA and Canada • RoHS compliance• Designed, tested, and built to incomparable Fluke quality standardsTechnical DataThe ESA620 Electrical Safety Analyzer, featuring smart technology to enhance productivity under any standard, represents the next generation in portable electrical safety testers. With selections of three test loads, two protective earth test currents and two insulation test voltages, this versatile device performs all primary electrical safety tests as well as several additional leakage tests for premium standards compliance worldwide.A convenient 20 A device receptacle broadens the range of equipment that can be tested using the ESA620. Standard 2-wire and optional 4-wire protective earth measurement capabilities offer first-rate time savings, while new DSP technology offers better accuracy of leakage measurements throughout specified ranges.Equipped with ten unique safety-enhanced ECG posts, the ESA620 offers simulation of ECG and performance waveforms so both electrical safety and basic tests on patient monitors can be performed with a single connection. When combined with optional Ansur computer-based software, the ESA620 allows for test procedure automation, the capture of results and comparison to standard limits, printed reports, and total digital data management.Key featuresSpecifications2 Fluke Biomedical ESA620 Electrical Safety Analyzer*No-cost extended warranty available after first-year calibration at any Fluke Biomedical authorized service center.ESA620 Electrical Safety Analyzer Fluke Biomedical 3Models2785725 ESA620 Electrical Safety Analyzer US, 115 V 20 A 3051408 ESA620 Electrical Safety Analyzer EUR, 230 V 3051390 ESA620 Electrical Safety Analyzer FR, 230 V 3051413 ESA620 Electrical Safety Analyzer ISR, 230 V 3051424 ESA620 Electrical Safety Analyzer ITA, 230 V 3051436 ESA620 Electrical Safety Analyzer AUS, 230 V 3051449 ESA620 Electrical Safety Analyzer UK, 230 V 3051451 ESA620 Electrical Safety Analyzer SWI, 230 VStandard accessories2814967 Operator’s Manual CD2814971 Multilingual Getting Started Guide 2195732 15 A to 20 A Adapter (USA only) 2814980 Carrying Case 1626219 Data Transfer Cable Power Cord (country specific)ESA620 Accessory Kit (country specific)Optional accessories3116463 Ansur ESA620 Plug-In 1903307 Retractable Test Leads 2242165 Ground Pin Adapter2067864 Kelvin Cable Set for 4-Wire MeasurementOrdering informationFluke Biomedical.Better products. More choices. One company.Fluke Biomedical 6045 Cochran RoadCleveland, OH 44139-3303 U.S.A.Fluke Biomedical Europe Science Park Eindhoven 5110 5692EC Son, The NetherlandsFor more information, contact us:In the U.S.A. (800) 850-4608 or Fax (440) 349-2307In Europe/M-East/Africa +31 40 267 5435 or Fax +31 40 267 5436From other countries +1 (440) 248-9300 or Fax +1 (440) 349-2307Email:*************************Web access: ©2007-2008 Fluke Biomedical. Specifications subject to change without notice. Printed in U.S.A. 9/2008 3086339 D-EN-N Rev CModification of this document is not permitted without written permission from Fluke Corporation.About Fluke Biomedicalfor all your equipment calibration needs.range of software and hardware tools to meet today’s challenges.Fluke Biomedical Regulatory Commitmentcertified and our products are:• CE Certified, where required • NIST Traceable and Calibrated• UL, CSA, ETL Certified, where required • NRC Compliant, where required。
DIN_VDE_0126-1-1_中文版
目录1. 前言2. 参考标准3. 定义4. 要求4.1 功能上的安全4.2 电压监控4.3 频率监控4.4 直流电流监控4.5 隔离运行的识别4.6 标识4.7 特殊要求5. 通用要求6. 型式测试6.1 功能上的安全6.2 电压监控6.3 频率监控6.4 直流电流监控6.5 隔离运行的识别6.6 故障电流监控7 例行测试8 安装要求附录A 声明A.1 其余识别隔离运行的方法A.2 频率界限A.3 发电机的运作A.4 短时间关机推荐书目图1 自动断路器的示意图（例如太阳能设备）图2 按照6.5.1 的测试电路－内置于逆变器中的断路器（举例）图3 按照6.5.2 的测试电路－内置于逆变器中的断路器（举例）图4 按照6.6.2.1 的测试电路－单相交流电逆变器的运行表 1 最大断开时间1. 应用范围应用范围自动断路器作为安全开关作用于发电装置和低压网络之间，并且作为随时配电网络供应商使用的带隔离功能的断路装置。
这一断路器用于阻止发电装置给跟其余电网分离的一个子网络（隔离运作）意外供电，以及按照 DIN VDE 0105－100 （VDE 0105－100）， 6.2 列出的措施提供保护－防止操作人员在子网络中触电。
－避免操作工具接触危险电压和频率。
－避免使用人员接触危险电压和频率。
－避免设备由于发电装置的故障而被供电。
当低压网络出现故障时，自动断路器使发电装置避免－危险电压－危险频率自动断路器并非使发电装置避免过载和短路。
这个保护功能应另外按照DIN VDE 0100-712(VDE0100-712), DIN VDE 0100-430(VDE 0100-430)和 DIN VDE 0100-530 (VDE 0100-530)去确认。
2. 参考标准参考标准对于此标准的使用，需要使用到下列标准。
具体日期标注的标准，则使用该日期版本。
没有具体日期标注的则使用最新的版本（包括所有的修改）。
DIN EN 50160: 2000-03, 公共电网的电压标识。
DIN_VDE_0126-1-1_中文版
目录1. 前言2. 参考标准3. 定义4. 要求4.1 功能上的安全4.2 电压监控4.3 频率监控4.4 直流电流监控4.5 隔离运行的识别4.6 标识4.7 特殊要求5. 通用要求6. 型式测试6.1 功能上的安全6.2 电压监控6.3 频率监控6.4 直流电流监控6.5 隔离运行的识别6.6 故障电流监控7 例行测试8 安装要求附录A 声明A.1 其余识别隔离运行的方法A.2 频率界限A.3 发电机的运作A.4 短时间关机推荐书目图1 自动断路器的示意图（例如太阳能设备）图2 按照6.5.1 的测试电路－内置于逆变器中的断路器（举例）图3 按照6.5.2 的测试电路－内置于逆变器中的断路器（举例）图4 按照6.6.2.1 的测试电路－单相交流电逆变器的运行表 1 最大断开时间1. 应用范围应用范围自动断路器作为安全开关作用于发电装置和低压网络之间，并且作为随时配电网络供应商使用的带隔离功能的断路装置。
这一断路器用于阻止发电装置给跟其余电网分离的一个子网络（隔离运作）意外供电，以及按照 DIN VDE 0105－100 （VDE 0105－100）， 6.2 列出的措施提供保护－防止操作人员在子网络中触电。
－避免操作工具接触危险电压和频率。
－避免使用人员接触危险电压和频率。
－避免设备由于发电装置的故障而被供电。
当低压网络出现故障时，自动断路器使发电装置避免－危险电压－危险频率自动断路器并非使发电装置避免过载和短路。
这个保护功能应另外按照DIN VDE 0100-712(VDE0100-712), DIN VDE 0100-430(VDE 0100-430)和 DIN VDE 0100-530 (VDE 0100-530)去确认。
2. 参考标准参考标准对于此标准的使用，需要使用到下列标准。
具体日期标注的标准，则使用该日期版本。
没有具体日期标注的则使用最新的版本（包括所有的修改）。
DIN EN 50160: 2000-03, 公共电网的电压标识。
Leviton ATLAS-X1 Cat 6A Component-Rated UTP QUICKP
Page 1 of 2APPLICATIONThe ATLAS-X1 Cat 6A Component-Rated UTP QUICKPORT Jack supports 10GBASE-T networks. The jack is part of a complete ATLAS-X1 Cat 6A UTP system, ideal for the most demanding mission-critical network applications. The connector supports emerging technologies and will easily adapt to network trends.SPECIFICATIONThe jack shall meet or exceed the requirements for channel and component-level electrical transmission performance as described in ANSI/TIA-568.2-D (Cat 6A), ISO/IEC11801-1 (Class E A ), and EN 50173-1 (Class E A ). The jack shall be compliant with ANSI/TIA-1096-A, c(UL)us Listed, and be independently verified for electrical transmission performance and power delivery. The jack body shall be made of die-cast zinc and all plastic components shall be made of high-impact, fire-retardant plastic rated UL 94V-0. The jack shall support tool-free termination and re-termination and shall not require a specialized termination tool. The jack wiring shall be universal to accommodate T568A and T568B wiring schemes. The jack shall be available in 13 colors; more than established by the ANSI/TIA-606-C standard. The jack shall be offered in standard and shuttered styles and select jacks shall be supplied with interchangeable icons. The jack shall be compliant with IEEE 802.3 PoE Type 1, 2, 3, 4 (100 watts max).DESIGN CONSIDERATIONS• Use in any QUICKPORT™ housing to support Cat 6A UTP connectivity in surface-mount, flush-mount, or modular furniture outlets and field-configurable panels• Can be used in conjunction with other QUICKPORT snap-in modules for voice/data/video applications over UTP , coax, and fiber• To identify ports, use different colored modules andicons for each application (full selection of ANSI/TIA-606 compatible colors, 13 available)• Robust housing and shutter protects the jack in harsh environmentsATLAS-X1™ Cat 6A Component-Rated UTP QUICKPORT™ Jack6AUJK-xx6, ICONS-ICxFEATURES• Independently tested and guaranteed to exceed all component, permanent link, and channel margins• Patented Retention Force Technology™ (RFT) protects against tine damage and increases system longevity • For Power over Ethernet, RFT maintains contact force between plug and jack, preventing arcing from intermittent disconnects• Unique design supports tool-free termination andre-termination and requires no specialized termination tool • Short jack design supports a wider range of applications (e.g. shallow boxes, enclosures, bend radius, etc.)• Terminates from 26 to 22 AWG solid or stranded conductors for use on various cable types• Robust IDCs can withstand 20 re-termination cycles and jack contacts are tested for 750 plug-mating cycles to ensure system longevity• Available in 13 ANSI/TIA-606-C compatible colors • Tested and approved for use in air-handling spaces (plenum rating) in accordance with UL Standard 2043• Select jacks available with interchangeable icons (voice, data, A/V, blank) for easy ID• Jack with internal shutter protects against dust and debris • Solid metal body dissipates 53% more heat than plastic, minimizing damage from excess heat in PoE applications • Tine geometry prevents arcing damage where plug and jack make contactSTANDARDS & REGULATIONS• ANSI/TIA-568.2-D (Cat 6A)• ISO/IEC 11801-1 (Cat 6A)• EN 50173-1 (Cat 6A)• ANSI/TIA-1096-A (formerly FCC Part 68)• IEC 60603-7 (includes IEC 60512-5-2)• IEC 60512-99-002• IEEE 802.3 PoE Type 1, 2, 3, 4 (100 watts max)• Cisco UPOE, UPOE+ (90 watts max)• Power over HDBaseT™ PoH (95 watts max)• c(UL)us Listed (UL 1863)• UL 2043 Plenum Certified • RoHS 3• ETL verified to meet the IEC 60512-99-002 standard for support of IEEE 802.3 Type 4 PoE (100 watt) applicationsCOUNTRY OF ORIGINUSA and Mexico (Contact Customer Service for details)6AUJK-xx6, ICONS-ICxUSANetwork Solutions Headquarters +1 (800) 722 2082 *******************Leviton Berk-Tek Cable : +1 (800) 237 5835 ************************Asia Pacific+852 3620 2602********************Canada+1 (800) 461 2002**********************Europe+44 (0) 1592 772124 **********************Latin AmericaMX: +52 (55) 2128 6286 LATAM: +52 (55) 2333 5963 *********************Middle East & Africa +971 (4) 247 9800 *******************NETWORK SOLUTIONS PRODUCTS ARE AVAILABLE WORLDWIDE IN OVER 100 COUNTRIES. VISIT US ONLINE AT /NS TO LEARN MORE.Page 2 of 2For further support information, visit /ns/support6AUJK-xx6, ICONS-ICx6AUJK-xx6, ICONS-ICxMECHANICAL SPECIFICATIONSDimensions:See belowMaterials: Jack Body: Die-cast zincSpring-Wire Contacts: High quality, copper-based alloy, plated with 50 microinches of gold for lowest contact resistance andmaximum life Temp. (Storage):Temp. (Installation): Temp. (Operating):Humidity (Max.):WARRANTY INFORMATIONFor Leviton product warranties, go to /ns/warrantyPART NUMBERDescriptionStandard Jack Jack with Shutter GREENPACK™12-Pack Standard Jack ATLAS-X1™ Cat 6A Component-Rated UTP QUICKPORT™ Jack, white 6AUJK-RW66AUJK-SW66AUJK-CW6ATLAS-X1 Cat 6A Component-Rated UTP QUICKPORT Jack, light almond 6AUJK-RT66AUJK-ST6—ATLAS-X1 Cat 6A Component-Rated UTP QUICKPORT Jack, ivory 6AUJK-RI66AUJK-SI6—ATLAS-X1 Cat 6A Component-Rated UTP QUICKPORT Jack, yellow 6AUJK-RY66AUJK-SY6—ATLAS-X1 Cat 6A Component-Rated UTP QUICKPORT Jack, orange 6AUJK-RO66AUJK-SO6—ATLAS-X1 Cat 6A Component-Rated UTP QUICKPORT Jack, crimson 6AUJK-RC66AUJK-SC6—ATLAS-X1 Cat 6A Component-Rated UTP QUICKPORT Jack, dark red 6AUJK-RR66AUJK-SR6—ATLAS-X1 Cat 6A Component-Rated UTP QUICKPORT Jack, purple 6AUJK-RP66AUJK-SP6—ATLAS-X1 Cat 6A Component-Rated UTP QUICKPORT Jack, blue 6AUJK-RL66AUJK-SL66AUJK-CL6ATLAS-X1 Cat 6A Component-Rated UTP QUICKPORT Jack, green 6AUJK-RV66AUJK-SV6—ATLAS-X1 Cat 6A Component-Rated UTP QUICKPORT Jack, gray 6AUJK-RG66AUJK-SG6—ATLAS-X1 Cat 6A Component-Rated UTP QUICKPORT Jack, black6AUJK-RE66AUJK-SE66AUJK-CE6ATLAS-X1 Cat 6A Component-Rated UTP QUICKPORT Jack, brown6AUJK-RB66AUJK-SB6—Green (V)Blue (L)Purple (P)Crimson (C)Dark Red (R)Orange (O)Yellow (Y)Black (E)Gray (G)Ivory (I)Light Almond (T)Brown (B)Color-matched icons (ICONS-ICx) can be ordered separately in 72-quantity packs.x = icon color。
伊顿断路器
6
W6ຫໍສະໝຸດ IZM9系列：标配抽屉式IZM 91B 4- U16 CW
标准模块:
• 抽屉式本体: IZM91B4-U16W • 电动操作机构:220AC • 分闸线圈: 220AC • 合闸线圈: 220AC • 脱扣故障指示触点: 2a2b • 标准辅助触点 :4a4b • 门框 • 手柄 • 安全挡板 • 灭弧罩 • 接线端子 • 电源模块（只适合U，P型脱扣器） • 抽屉座
SPC-S-20/280/1 SPC-S-20/280/2 SPC-S-20/280/3 SPC-S-20/280/4
SPC-S-20/385/1 SPC-S-20/385/2 SPC-S-20/385/3 SPC-S-20/385/4
SPC-S-20/580/1
SPD-S-1+1 SPV-D40/1000
运最行大电持压续Uc
型号 固定式
额定（放k电A）电流In (8/20) µs
35
440
SPI-35/440
120
B 50
260
SPI-50/NPE
80
100
260
SPI-100/NPE
-
B+C
12.5
280
SPB-12/280
65
20
C
-
-
-
25
30
光D伏
-
-
-
-
-
10 40
运最行大电持压续Uc
385
© 2011 Eaton Corporation. All rights reserved.
3
3
伊顿低压配电产品——空气断路器 塑壳断路器 终端配电产品
© 2011 Eaton Corporation. All rights reserved.
ATMEGA16A中文资料
ATMEGA16A中文资料高性能,低功耗AVR 8-bit微控制器•高级RISC建筑– 131条指令–绝大多数为单时钟周期执行– 32 x 8通用工作寄存器–全静态工作–高达16吞吐量在MIPS 16 MHz–片2—cycle乘数高耐久性非易失性内存段– 16K字节的程序存储器，在系统内可编程Flash– 512字节的EEPROM– 1K字节内部SRAM–写/擦除周期：10，000闪光/ 100，000的EEPROM–数据保存：在20年85°C/100年在25°C（1)–可选引导具有独立锁定Bits代码段•在系统编程的片上引导程序•真Read-While-Write操作–锁编程软件安全JTAG (IEEE std。
1149.1兼容）接口–边界扫描功能根据JTAG标准–广泛的片上调试支持–编程闪存，EEPROM，熔丝位和锁定Bits通过JTAG接口外设特点–两个8—bit定时器/计数器具有独立预分频器和比较模式–一个16-bit定时器/计数器具有独立预分频器,比较功能和捕捉模式–实时计数器具有独立振荡器–四PWM频道– 8-channel, 10-bit ADC• 8单端通道• 7在TQFP 包装差分通道只有• 2在1x, 10x,差分通道具有可编程增益或200x–面向字节的两线串行接口可编程串行USART的––主/从串行接口SPI–可编程看门狗定时器具有独立片内振荡器–片内模拟比较器单片机的特殊功能–上电复位和可编程的掉电检测–内部振荡器校准RC–外部和内部中断源– 6种睡眠模式：空闲，ADC降噪，省电，省电，待机和扩展待机I / O和封装– 32可编程I / O线– 40—pin PDIP, 44—lead TQFP，和44—pad QFN/MLF 工作电压– 2。
7为- 5。
5V ATmega16A速度等级– 0 —为16 MHz ATmega16A功耗＠ 1 MHz, 3V，和25°C为ATmega16A–活动:0。
伊顿电气有限公司Eaton Electrical Ltd. DMVCD系列隔离开关使用说明书
DMVCD系列隔离开关使用说明书伊顿电气有限公司Eaton Electrical Ltd.装箱单随机文件和附件产品型号说明书合格证手柄操作轴柜外操作机构标准件限制件DMV63CD/3.41111DMV100CD/3.411111DMV63CD/3.4G 111111DMV100CD/3.4G 1111111DMV160-630CD/3.41111DMV160-630CD/3.4G 11111DMV1000CD/3.41112DMV1000CD/3.4G 111112DMV1250-1600CD/3.41114DMV1250-1600CD/3.4G111114尊敬的用户：欢迎您使用本公司生产的DMVCD系列隔离开关产品!为了您能安全正确地使用本系列产品,敬请您在安装调试和使用前熟读本说明书。
本产品符合GB/T14048.3、IEC60947-3标准，并通过了国家CCC认证。
目录一.用途 (4)二.产品的工作条件 (4)三.结构与特点 (4)四.主要规格及技术参数 (4)五.外型与安装尺寸 (5)六.安装方法 (9)七.使用与维修 (14)八.订货须知 (14)一、用途DMVCD系列隔离开关（以下简称开关）适用于交流50Hz，额定电压415V以下，额定电流为63～1600A。
在配电系统中做不频繁接通与分断电路及隔离电路用。
二、产品的工作条件开关在如下条件下可靠运行：安装地点的海拔高度不超过2000米；周围空气温度不超过+40℃，而且其24h内的平均温度值不超过+35℃；周围空气温度的下限为-5℃；最高温度为+40℃时，空气的相对湿度不超过50%，在较低的温度下可以允许有较高的相对湿度，例如20℃时达90%。
对由于温度变化偶尔产生的凝露应采取特殊的措施；污染等级为3级。
注：若预期使用条件与以上标准不同，应在下单前提出。
三、结构与特点开关由不饱和聚酯玻璃纤维增强模塑料(DMC)制造的外壳；弹簧储能加速机构能快速实现接通与分断；触头结构为并联双断点两个分离触头面，并由片状弹簧保证触头压力；开关能够自动确定通断的极限位置，而且具有明显的通断标记来指示通断位置。
BRAUN_E16超速保护系统介绍_兰杰
阀座型号不同也不能互换。 2 ） 速关阀的 4 个位置传感器都是电感式二 线制接近开关， 由隔离器进行供电， 隔离器跳线为 电平输入。经测试进入隔离器的电压约在 6. 25V 时引发隔离器输出电平转换， 靠近传感器 （ 90% 位置） 时隔离器输入电压为 7. 5V （ ＞ 6. 25V ） ， 隔 离器 OUT 灯灭， 输出触点接通 （ 常闭式 ） ， 输出高 电平（ 24V ） 至 BRAUN （ BRAUN 设置为高电平有 效） 。 离 开 传 感 器 后 隔 离 器 输 入 电 压 为 3. 6V （ ＜ 6. 25V） ， 隔离器 OUT 灯亮， 输出触点断开， 输 出低电平（ OV） 至 BRAUN。 4 4. 1 维护及调试
1 ） 3 只带有集成信号放大器的 A5S15 差动 霍尔传 感 器 提 供 速 度 检 测。 此 传 感 器 通 过 了 TV 电气安全等级认证， 支持 BRAUN 系统的传 感器故障诊断功能。 2 ） 每个测速通道都包括一块 E1667 监视器。 3 ） 通过 E1615 辅助继电器组合单元扩大联 锁输出通道。两套 BRAUN 都配置有 6 块继电器 卡， 前面 3 块继电器卡分别代表 3 路 2oo3 表决通 道， 每块卡上有 8 个 LED 灯， 表示有 4 组 8 路 （ 2 路为一组） 输出。后面 3 块继电器卡是前面 3 块 也是 4 组 8 路输出， 这样 6 块继 卡的进一步扩展，
状态在 ESD 系统的 OS 操作站上进行监视， 并进 行手工复位。蒸汽透平的 BRAUN 保护系统分别 由现场油动执行器 （ 速关阀 ） 和 5 只电磁阀组以 及主控 BRAUN / E16 构成。 1 1. 1 BRAUN / E16 系统 主控 BRAUN / E16
图1
艾特顿191796安全传感器说明书
Eaton 191796Eaton ESR5 Safety relay emergency stop/protective door/light curtain monitoring with wide range input, 24 V-230 VDC/ACGeneral specificationsEaton ESR5 Safety relay 191796ESR5-NO-31-UC 4015081923151114.5 mm 113 mm 22.5 mm 0.17 kgCertified by UL for use in Canada CSA-C22.2 No. 14-95 IEC/EN 60947-5-1 UL 508 2014/30/EU CE IEC 62061UL report applies to both US and Canada EN 50156-1 EN ISO 13849-1 ULUL File No.: E29184 IEC 61508, Parts 1-7 Machines 2006/42/EGProduct NameCatalog Number Model Code EANProduct Length/Depth Product Height Product Width Product Weight CertificationsScrew connectionStart button monitoring4 kV basic insulation between all current paths and enclosure 4 kV basic insulation between 23/24 and 33/34 enable signal current paths and 41/42 signaling current pathManual start3 Non-delayed enable current pathsSafe insulationAutomatic start6 kV reinforced insulation between all other current pathsDetachable clampsApproval according to ULStart inputFeedback circuit2-channel1-channel M3 screw terminalsTerminals: IP20Installation location: ≥ IP54IP20Enclosure: IP20Status indication of SmartWire-DT network: Green LED240 monthBasic deviceTop-hat rail fixing (according to IEC/EN 60715, 35 mm)Rail mounting possible22.5 mmIII2Electronic safety relaysLevel eCat. 4, CategorySIL 3, Safety integrity level, In accordance with IEC 61508 10 x 10-10, PFHd, Probability of failure per hourSILCL 3, Safety integrity level claim limitSIL 3, Safety integrity levelMonitoring of magnetic switchesMonitoring of emergency-stop circuitsIf the sensor circuit is interrupted, the safety relay switches toElectric connection type FeaturesFitted with:Functions Connection typeDegree of protectionLED indicatorLifetimeModelMounting methodMounting widthOvervoltage categoryPollution degreeProduct categorySafety performance level (EN ISO 13849-1) Safety parameter (IEC 62061)Stop category (IEC 60204)Suitable forsafe modeModule used to safely interrupt electrical circuits Monitoring of optoelectronic protection equipmentSafety relay for monitoring one or two-channel signal generators and control of actuators Max. 1 Hz, Input data AC/DCAs required 56 Months (Low Demand) 240 Months (High Demand)0.05 W5 A, DC-13 at 24 V, Outputs 795 - 1080 hPa (operation)Max. 2000 m-40 °C55 °C-40 °C85 °CCondensation: Non-condensing -40 °C55 °C< 75 %24 V40 W max., inductive load (τ = 40 ms), at 48 V DC 35 W max., inductive loadSwitching frequency TypeVoltage type Mounting position ProoftestSwitching capacityAir pressureAltitude Ambient operating temperature - min Ambient operating temperature - max Ambient storage temperature - min Ambient storage temperature - max Environmental conditions Operating temperature - min Operating temperature - max Relative humidity Rated control supply voltage (Us) at AC, 50 Hz - min Breaking powerEmergency stop category 0; emergency switching off Feedback circuit Light curtain Protective door230 V24 V230 V24 V230 V250 V230 V AC6 A gL/gG, For output circuits, External (τ = 40 ms), at 110 V DC1500 VA, max., resistive load (τ = 0 ms), at 250 V AC 48 W max., inductive load (τ = 40 ms), at 24 V DC 33 W max., inductive load (τ = 40 ms), at 220 V DC∞ ms, Simultaneity for inputs 1/2One- and two-channel< 100 ms typ. (at Uₑ in manual mode)< 150 ms typ. (at Uₑ in automatic mode)72 A² (ITH² = I1² + I2² + In²)Normally < 20 ms (when driven via the sensor circuits) 6 A N/O, Limiting continuous current2.7 W 0 W 0 W 0 A 2.9 W easySafety ES4P Safety Relay ESR5 - brochureDA-DC-00004572.pdfDA-DC-00004580.pdfeaton-safety-relays-esr5-safety-relay-characteristic-curve-003.eps eaton-safety-relays-esr5-safety-relay-characteristic-curve-010.eps eaton-safety-relays-esr5-safety-relay-characteristic-curve-002.eps eaton-safety-relays-esr5-safety-relay-characteristic-curve-004.epsRated control supply voltage (Us) at AC, 50 Hz - max Rated control supply voltage (Us) at AC, 60 Hz - minRated control supply voltage (Us) at AC, 60 Hz - max Rated control supply voltage (Us) at DC - minRated control supply voltage (Us) at DC - max Rated insulation voltage (Ui)Rated operational voltageShort-circuit protection InputNumber of inputsNumber of outputs (safety related, delayed) with contact Number of outputs (safety related, undelayed) with contact Number of outputs (signaling function, delayed) with contact Number of outputs (signaling function, undelayed) with contact Pick-up timeQuadratic summation currentReset timeUninterrupted currentEquipment heat dissipation, current-dependent PvidHeat dissipation capacity PdissHeat dissipation per pole, current-dependent PvidRated operational current for specified heat dissipation (In) Static heat dissipation, non-current-dependent Pvs Brochures Certification reports Characteristic curveMeets the product standard's requirements.Meets the product standard's requirements.Meets the product standard's requirements.Meets the product standard's requirements.Meets the product standard's requirements.Does not apply, since the entire switchgear needs to be evaluated.Does not apply, since the entire switchgear needs to be evaluated.Meets the product standard's requirements.Does not apply, since the entire switchgear needs to be evaluated.Meets the product standard's requirements.Does not apply, since the entire switchgear needs to be evaluated.Does not apply, since the entire switchgear needs to be evaluated.Is the panel builder's responsibility.Is the panel builder's responsibility.Is the panel builder's responsibility.Is the panel builder's responsibility.eaton-safety-relays-relay-esr5-safety-relay-dimensions-003.eps DA-CE-ETN.ESR5-NO-31-UCIL049009MLMN049014_ENesr5_no_31_uc.dwgesr5_no_31_uc.stpeaton-safety-relays-esr5-safety-relay-wiring-diagram-016.eps10.2.2 Corrosion resistance10.2.3.1 Verification of thermal stability of enclosures10.2.3.2 Verification of resistance of insulating materials to normal heat10.2.3.3 Resist. of insul. mat. to abnormal heat/fire by internal elect. effects10.2.4 Resistance to ultra-violet (UV) radiation10.2.5 Lifting10.2.6 Mechanical impact10.2.7 Inscriptions10.3 Degree of protection of assemblies10.4 Clearances and creepage distances10.5 Protection against electric shock10.6 Incorporation of switching devices and components10.7 Internal electrical circuits and connections10.8 Connections for external conductors10.9.2 Power-frequency electric strength10.9.3 Impulse withstand voltage DrawingseCAD model Installation instructions Manuals and user guides mCAD modelWiring diagramsEaton Corporation plc Eaton House30 Pembroke Road Dublin 4, Ireland © 2023 Eaton. All rights reserved. Eaton is a registered trademark.All other trademarks areproperty of their respectiveowners./socialmediaIs the panel builder's responsibility.The panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.Is the panel builder's responsibility. The specifications for the switchgear must be observed.Is the panel builder's responsibility. The specifications for the switchgear must be observed.The device meets the requirements, provided the information in the instruction leaflet (IL) is observed.10.9.4 Testing of enclosures made of insulating material 10.10 Temperature rise10.11 Short-circuit rating10.12 Electromagnetic compatibility10.13 Mechanical function。
Eaton DE11可变速启动器180651说明书
Eaton 180651Eaton DE11 Variable speed starters, Rated operational voltage 230 V AC, 1-phase, Ie 2.3 A, 0.37 kW, 0.5 HP, Radio interference suppression filter DE11-122D3FN-N20NEspecificaciones generalesEaton DE11 Variable speed starter 1806514015081758166169 mm 230 mm 45 mm 1.04 kgIEC/EN61800-3Safety requirements: IEC/EN 61800-5-1 UL File No.: E172143 IEC/EN61800-5 CSA-C22.2 No. 14UL Category Control No.: NMMS, NMMS7 UL UL 508CUL report applies to both US and Canada CEIEC/EN 61800-3 CUL RCMSpecification for general requirements: IEC/EN 61800-2 RoHS, ISO 9001Certified by UL for use in CanadaProduct NameCatalog Number EANProduct Length/Depth Product Height Product Width Product Weight Certifications Catalog NotesModel Code240 V0.92 kVA2.3 A0.37 kW2.2 AIs the panel builder's responsibility. The specifications for the switchgear must be observed.240 V AC, 1-phase230 V AC, 1-phaseMeets the product standard's requirements.0.37 kW250 VMeets the product standard's requirements.-40 °C200 VRadio interference suppression filterPC connection0 Hz60 °C Drives - Product range catalogeaton-frequency-inverter-dimensions-009.epseaton-frequency-inverter-3d-drawing-017.epsDA-CE-ETN.DE11-122D3FN-N20NHVAC, water/wastewater and industrial mediums - brochure Number 1 in efficiency The easiest way of variable motor speed PowerXL DE1 Variable Speed StarterDA-SW-Codesys 2 SWD for DC1 and DE1DA-SW-drivesConnect - InstallationshilfeDA-SW-DE11 CANopen CODESYS2 LibraryDA-SW-DE1 ModbusRTU V1_00 LibraryDA-SW-drivesConnectDA-SW-drivesConnect - installation helpDA-SW-Codesys 3 SWD for DC1 and DE1DA-SW-USB Driver DX-COM-STICK3-KITDA-SW-DE11 CANopen ConfigFile 210DA-SW-DE11 CANopen CODESYSV3 LibraryDA-SW-USB Driver PC Cable DX-CBL-PC-1M5DA-SW-DE11 CANopen ConfigFile 203DA-SW-Driver DX-CBL-PC-3M0MN040011_ESDA-DC-00004551.pdfDA-DC-00004556.pdfIL040005ZUDA-CS-de1_fs1_ip20DA-CD-de1_fs1_ip20DX-COM-STICK3_ConnectionMains voltage - maxApparent power at 230 VRated operational current for specified heat dissipation (In) Rated operational power at 220/230 V, 50 Hz, 1-phase Assigned motor current IM at 440 - 480 V, 60 Hz, 150% overload 10.11 Short-circuit ratingRated operational voltage10.4 Clearances and creepage distancesOutput at quadratic load at rated output voltage - maxOutput voltage - max10.2.3.1 Verification of thermal stability of enclosuresAmbient storage temperature - minMains voltage - minFitted with:Output frequency - minAmbient operating temperature at 150% overload - max Starting current - max CatálogosDibujoseCAD modelFolletosGuías de Usuario Informes de certificación Instrucciones de montaje mCAD modelNotas de aplicación200 %, IH, max. starting current (High Overload), For 1.875 seconds every 600 seconds, Power section2 A60 °COP-Bus (RS485), built inModbus RTU, built inCANopen®, built in0.5 HP300 Hz240 V AC, 3-phase230 V AC, 3-phase16 kHz, 4 - 32 kHz adjustable (audible), fPWM, Power section, Main circuitParameterization: drivesConnectParameterization: drivesConnect mobile (App) Parameterization: FieldbusParameterization: KeypadOperation (with 150 % overload)-10 °C≤ 0.6 A (max. 6 A for 120 ms), Actuator for external motor brakeDoes not apply, since the entire switchgear needs to be evaluated.2.3 A Update DX-COM-STICK3How does the internal motor protection work? Starting, Stopping and OperationSet point settingConformal CoatingThe OP System Bus - Parameterizing - ControlQuick-Start-Guide DE1 (english)Fire modeMotor data Motor Protection V/f curves Slip Compensation I/O ConfigurationAccess to Parameter Level 2 Parameter Lock Load Default Quick-Start-Guide DE11 (english)Assigned motor current IM at 230 V, 50 Hz, 150% overload Ambient operating temperature - maxCommunication interfaceAssigned motor power at 115/120 V, 60 Hz, 1-phase Output frequency - maxOutput voltage (U2)Switching frequencyFeaturesHeat dissipation detailsAmbient operating temperature - minBraking currentNumber of HW-interfaces (serial TTY)10.6 Incorporation of switching devices and components Nominal output current I2NAssigned motor current IM at 220 - 240 V, 60 Hz, 150% overload 2.2 A10.2.6 Mechanical impactDoes not apply, since the entire switchgear needs to be evaluated.10.3 Degree of protection of assembliesDoes not apply, since the entire switchgear needs to be evaluated.Assigned motor current IM at 115 V, 50 Hz, 150% overload2 AProduct categoryVariable speed starterRadio interference classC1: for conducted emissions onlyC2, C3: depending on the motor cable length, the connected load, and ambient conditions. External radio interference suppression filters (optional) may be necessary.Optional external radio interference suppression filter for longer motor cable lengths and for use in different EMC environmentsAssigned motor current IM at 110/120 V, 60 Hz, 150% overload 2.2 AHeat dissipation capacity Pdiss0 WAssigned motor power at 460/480 V, 60 Hz, 3-phase0.5 HPNumber of HW-interfaces (RS-422)Mains current distortion120 %ProtocolOther bus systemsMODBUSEtherNet/IPCAN10.9.2 Power-frequency electric strengthIs the panel builder's responsibility.Overvoltage categoryIIIDegree of protectionIP20NEMA OtherAmbient storage temperature - max70 °CRated impulse withstand voltage (Uimp)2000 VOutput at linear load at rated output voltage - max0.37 kWLeakage current at ground IPE - max< 10 mA (DC-operated)< 3.5 mA (AC-operated)Converter typeU converterFrame sizeFS110.2.2 Corrosion resistanceMeets the product standard's requirements.Supply frequency50/60 Hz10.2.4 Resistance to ultra-violet (UV) radiationMeets the product standard's requirements.10.2.7 InscriptionsMeets the product standard's requirements.Shock resistance15 g, Mechanical, According to IEC/EN 60068-2-27, 11 msApplication in domestic and commercial area permittedYesNumber of inputs (analog)1 (parameterizable, 0 - 10 V DC, 0/4 - 20 mA)Number of phases (output)310.12 Electromagnetic compatibilityIs the panel builder's responsibility. The specifications for the switchgear must be observed.10.2.5 LiftingDoes not apply, since the entire switchgear needs to be evaluated.Number of HW-interfaces (RS-485)1Number of HW-interfaces (industrial ethernet)10.8 Connections for external conductorsIs the panel builder's responsibility.ProtectionFinger and back-of-hand proof, Protection against direct contact (BGV A3, VBG4)Number of relay outputs1 (parameterizable, N/O, 6 A (250 V, AC-1) / 5 A (30 V, DC-1))Application in industrial area permittedYesClimatic proofing< 95 average relative humidity (RH), no condensation, no corrosionConnection to SmartWire-DTIn conjunction with DX-NET-SWD3 SmartWire DT moduleYesStatic heat dissipation, non-current-dependent Pvs0 W10.9.3 Impulse withstand voltageIs the panel builder's responsibility.Voltage rating - max240 VOverload current IL at 150% overload3.45 AInput current ILN at 150% overload6.2 ANumber of HW-interfaces (RS-232)Number of inputs (digital)4 (parameterizable, 10 - 30 V DC)Rated control supply voltage10 V DC (Us, max. 0.2 mA)Cable lengthC1 ≤ 5 m, Radio interference level, maximum motor cable lengthC3 ≤ 25 m, Radio interference level, maximummotor cable lengthC2 ≤ 10 m, Radio interference level, maximum motor cable length10.5 Protection against electric shockDoes not apply, since the entire switchgear needs to be evaluated.Mounting positionVerticalMains switch-on frequencyMaximum of one time every 30 seconds10.13 Mechanical functionThe device meets the requirements, provided the information in the instruction leaflet (IL) is observed.10.9.4 Testing of enclosures made of insulating materialIs the panel builder's responsibility.Heat dissipation per pole, current-dependent Pvid0 WElectromagnetic compatibility1st and 2nd environments (according to EN 61800-3)Resolution0.03 Hz (Frequency resolution, setpoint value)Assigned motor power at 460/480 V, 60 Hz0.5 HPRelative symmetric net voltage tolerance10 %Equipment heat dissipation, current-dependent Pvid20 WRated operational current (Ie)2.3 A at 150% overload (at an operating frequency of 16 kHz and an ambient air temperature of +50 °C)Number of outputs (analog)Suitable forBranch circuits, (UL/CSA)Apparent power at 240 V0.96 kVANumber of HW-interfaces (USB)Operating modeSpeed control with slip compensationU/f controlRated frequency - min45 HzDelay time< 10 ms, On-delay< 10 ms, Off-delayNumber of outputs (digital)Power consumption20 W10.2.3.2 Verification of resistance of insulating materials to normal heatMeets the product standard's requirements.10.2.3.3 Resist. of insul. mat. to abnormal heat/fire by internal elect. effectsMeets the product standard's requirements.Number of HW-interfaces (other)Rated frequency - max66 HzVibrationResistance: According to EN 61800-5-1Short-circuit protection (external output circuits)Type 1 coordination via the power bus' feeder unit, Main circuit10.7 Internal electrical circuits and connectionsIs the panel builder's responsibility.Braking torqueAdjustable to 100 %, DC - Main circuitMax. 30 % MN, Standard - Main circuitAmbient operating temperature at 150% overload - min-10 °CRelative symmetric net frequency tolerance10 %10.10 Temperature riseThe panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.Eaton Corporation plc Eaton House30 Pembroke Road Dublin 4, Ireland © 2023 Eaton. All Rights Reserved. Eaton is a registered trademark.All other trademarks areproperty of their respectiveowners./socialmedia2 A0.5 HP110 W at 50% current and 0% speed 10.4 W at 50% current and 90% speed 11.6 W at 50% current and 50% speed 16.8 W at 100% current and 0% speed 16.8 W at 100% current and 50% speed 18.3 W at 100% current and 90% speed 5.6 W at 25% current and 0% speed 5.6 W at 25% current and 50% speed 10 A, UL (Class CC or J), Safety device (fuse or miniature circuit-breaker), Power Wiring 0Above 1000 m with 1 % derating per 100 m Max. 2000 mAssigned motor current IM at 400 V, 50 Hz, 150% overload Number of HW-interfaces (parallel)Assigned motor power at 230/240 V, 60 Hz, 1-phase Number of phases (input)Heat dissipation at current/speed Short-circuit protection ratingNumber of interfaces (PROFINET)Altitude。
TCL机型与遥控器对应表ok
型号
款式 RC-C09T RC-E16T RC-C16T RC-C12T RC-C12T
RC-F28T RC-038 RC-B01
RC-E09T RC-C14T RC-C14T
RC-C01T RC-C01T RC-C07T RC-C01T RC-C07T RC-B07T RC-B06T RC-E33T RC-B02T
TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL TCL
RC-F64T RC-042
113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169
2901A 2129C 2511F 2515DZ 2515DZ 2516B 2516BI 2516BP 2516BZ 2516EF 2518E 2518EF 2518EW 2535A 2536F 2536G 2536W 2539D 2566B 2575D 2580DB 2906A 2906E 2906E 2909A 2909B 2909B 2910G 2910GW 2911 2911DI 2911DZ 2913A 2913E 2913EB 2913UI 2915DZ 2916D 2916P 2916P 2918E 2918EW 2919AZ 2926UI 2927D 2927D 2939D 2939DR 2939R 2939W 2952AL 2952B 2956D 2956D 2966A/G 2966DG 2966F
艾特顿167123产品说明书
Eaton 167123Eaton Moeller series xEffect - FRCmM-NA RCCB. Residual currentcircuit breaker (RCCB), 40A, 2p, 300mA, type G/A, ULGeneral specificationsEaton Moeller series xEffect - FRCmM-NA RCCB167123FRCMM-40/2/03-G/A-NA401508163624280 mm71 mm35 mm0.22 kg RoHS conformUL 1053 IEC 61008 EN 61008 ÖVE E 8601 EN45545-2 IEC 61373Additionally protects against special forms of residual pulsating DC which have not been smoothed.Product Name Catalog NumberModel CodeEAN Product Length/Depth Product Height Product Width Product Weight Compliances Certifications Catalog Notes40 AIs the panel builder's responsibility. The specifications for the switchgear must be observed.7035-35 °CMeets the product standard's requirements.Is the panel builder's responsibility. The specifications for the switchgear must be observed.Quick attachment with 2 latch positions for DIN-rail IEC/EN 60715DIN rail40 ADoes not apply, since the entire switchgear needs to be evaluated.0.3 A184 V AC - 250 V AC, 196 V AC - 305 V AC (UL)Meets the product standard's requirements.Short time-delayed10 ms delay at 50 Hz8 ms delay at 60 HzInterlocking device500 A eaton-rcd-application-guide-br019003en-en-us.pdfUL 1053 DIN Rail RCCBeaton-xeffect-industrial-switchgear-range-catalog-ca003002en-en-us.pdf Eaton's Volume 4—Circuit Protectioneaton-xeffect-frcmm-na-rccb-catalog-ca003019en-en-us.pdfDA-DC-03_FRCm03_FRCm.-NA_181019eaton-circuit-breaker-xeffect-frcmm-na-rccb-dimensions.epsETN.FRCMM-40_2_03-G_A-NAMA180503312DA-CD-f9_ul1053_2pDA-CS-f9_ul1053_2pEaton Specification Sheet - 167123eaton-xeffect-frcmm-rccb-wiring-diagram.jpgeaton-circuit-breaker-xeffect-frcmm-na-rccb-wiring-diagram.epsRated operational current for specified heat dissipation (In) 10.11 Short-circuit ratingRAL-numberPermitted storage and transport temperature - min10.4 Clearances and creepage distances10.12 Electromagnetic compatibilityMounting MethodAmperage Rating10.2.5 LiftingRated fault current - maxTest circuit range10.2.3.1 Verification of thermal stability of enclosures Tripping timeFitted with:Rated residual making and breaking capacity Application notesBrochuresCatalogsCertification reports DrawingseCAD modelInstallation instructions mCAD model Specifications and datasheets Wiring diagramsFrequency rating50 Hz / 60 Hz10.8 Connections for external conductorsIs the panel builder's responsibility.Fault current rating300 mATerminal protectionFinger and hand touch safe, DGUV VS3, EN 50274Special featuresFRCmM-NAResidual current circuitbreakersType G/A (ÖVE E 8601)Sensitivity typePulse-current sensitiveAmbient operating temperature - max40 °CHeat dissipation per pole, current-dependent3.9 WClimatic proofing25-55 °C / 90-95% relative humidity according to IEC 60068-2Built-in depth70.5 mmShort-circuit ratingMax. admissible back-up fuse: 63 A gG/gL, 70 A class J fuse (UL)FeaturesResidual current circuit breakerAdditional equipment possibleLifespan, electrical4000 operationsTerminal capacity (cable)M5 (with cross-recessed screw as defined in EN ISO 4757-Z2, PZ2)Connectable conductor cross section (solid-core) - min1.5 mm²Contact position indicator colorRed / green10.9.3 Impulse withstand voltageIs the panel builder's responsibility.Number of polesTwo-poleTerminal capacity (solid wire)1.5 mm² - 35 mm²Ambient operating temperature - min-25 °C10.6 Incorporation of switching devices and componentsDoes not apply, since the entire switchgear needs to be evaluated.Rated short-circuit strength10 kA with back-up fuse5 kA (UL, as per CSA)10.5 Protection against electric shockDoes not apply, since the entire switchgear needs to be evaluated.Used withFRCmM-NAResidual current circuit breakersType G/A (�VE E 8601)Mounting positionAs requiredEquipment heat dissipation, current-dependent7.8 W10.13 Mechanical functionThe device meets the requirements, provided the information in the instruction leaflet (IL) is observed.10.2.6 Mechanical impactDoes not apply, since the entire switchgear needs to be evaluated.10.9.4 Testing of enclosures made of insulating materialIs the panel builder's responsibility.ApplicationSwitchgear for export to North America (UL-listed)10.3 Degree of protection of assembliesDoes not apply, since the entire switchgear needs to be evaluated.Voltage rating (IEC/EN 60947-2)240 V AC / 415 V ACVoltage typeACTerminal capacity (stranded cable)16 mm² (2x)Leakage current typeAFrame45 mmBuilt-in width (number of units)35 mm (2 SU)Terminals (top and bottom)Lift terminalsAmbient humdity range5 - 95 %Impulse withstand current3 kA (8/20 μs) surge-proofWidth in number of modular spacings210.2.3.2 Verification of resistance of insulating materials to normal heatMeets the product standard's requirements.10.2.3.3 Resist. of insul. mat. to abnormal heat/fire by internal elect. effectsMeets the product standard's requirements.Lifespan, mechanical10000 operationsStatus indicationWhite / blue10.9.2 Power-frequency electric strengthIs the panel builder's responsibility.Connectable conductor cross section (solid-core) - max35 mm²Degree of protectionIP20, IP40 with suitable enclosureIP20Rated short-time withstand current (Icw)10 kAOvervoltage tested - max530 VPollution degree210.7 Internal electrical circuits and connectionsIs the panel builder's responsibility.Connectable conductor cross section (multi-wired) - min 1.5 mm²Rated impulse withstand voltage (Uimp)4 kV10.10 Temperature riseThe panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.FunctionsShort-time delayed trippingVoltage rating (UL)480Y/277 V, 60 HzConnectable conductor cross section (multi-wired) - max 16 mm²TypeCurrent test marks as perinscriptionMaximum operatingtemperature is 75 °C:Starting at 40 °C, the max.permissible continuouscurrent decreases by 2.5%for every 1 °CThe maximum operatingcurrent of back-up fuse mustnot exceed the residualcurrent circuit breaker'srated operational current10.2.2 Corrosion resistanceMeets the product standard's requirements.10.2.4 Resistance to ultra-violet (UV) radiationMeets the product standard's requirements.10.2.7 InscriptionsMeets the product standard's requirements.Eaton Corporation plc Eaton House30 Pembroke Road Dublin 4, Ireland © 2023 Eaton. All Rights Reserved. Eaton is a registered trademark.All other trademarks areproperty of their respectiveowners./socialmedia3 kA60 °C40 A gG/gL0.3 A200 mA277 V440 VSurge current capacity Permitted storage and transport temperature - max Admissible back-up fuse overload - max Rated fault current - min Pick-up current Rated operational voltage (Ue) - max Rated insulation voltage (Ui)。
电气安全检测仪器ESA601入门手册
阿里阶梯测试仪系列E5061A、E5062A的数据手册说明书
AgilentENA-L RF Network Analyzers E5061A, 300 kHz to 1.5 GHzE5062A, 300 kHz to 3 GHzData SheetDefinitionsAll specifications apply over a 23 °C ±5 °C range (unless otherwise stated) and 90 minutes after the instrument has been turned on.Specification (spec.):Warranted performance. Specifications include guardbands to account for the expected statistical performance distribution, measurement uncertainties, and changes in performance due to environmental conditions.Supplemental information is intended to provide information that is helpful for using the instrument but that is not guaranteed by the product warranty. Typical (typ.):Describes performance that will be met by a minimum of 80% of all products. It is not guaranteed by the product warranty.Supplemental performance data (SPD):Represents the value of a parameter that is most likely to occur; the expected mean or average. It is not guaranteed by the product warranty.General characteristics:A general, descriptive term that does not imply a level of performance.23Corrected system performanceThe specifications in this section apply for measurements made with the Agilent E5061A/E5062A network analyzer with the following conditions:• No averaging applied to data• Environmental temperature of 23 °C ±5 °C, with less than 1 °C deviation from the calibration temperature• Response and isolation calibration not omittedTable 1-1 System dynamic range 1 2Description Specification SPD System dynamic range300 kHz to 1 MHz, IF bandwidth = 3 kHz 90 dB1 MHz to 3 GHz, IF bandwidth = 3 kHz 95 dB 300 kHz to 1 MHz, IF bandwidth = 10 Hz 115 dB 1 MHz to 3 GHz, IF bandwidth = 10 Hz120 dB130 dB 1. The test port dynamic range is calculated as the difference between the test port rms noise floor and the source maximum output power. The effective dynamic range must take measurement uncertainty and interfering signals into account.2. Applicable to the units with serial prefix MY442 and above .System dynamic range; specification and measurement example3.0E+055.0E+08 1.0E+09 1.5E+09 2.0E+09 2.5E+09Test frequency [/Hz]S y s t e m d y n a m i c r a n g e [/d B ]4Table 1-2 Corrected system performance with Type-N 50 Ω connectors, 85032F calibration kit, full 2-port calibrationNetwork analyzer: E5061A/E5062A, calibration kit: 85032F (Type-N, 50 Ω), calibration: full 2-portIF bandwidth = 10 Hz, No averaging applied to data, environmental temperature = 23 °C ±5 °C with < 1 °C deviation from calibration temperature, isolation calibration not omittedDescription Specification (dB)300 kHz to 1.5 GHz1.5 to 3 GHzDirectivity 49 46Source match 41 40Load match 49 46 Reflection tracking ±0.011 ±0.021 Transmission tracking±0.015±0.018Transmission uncertainty (specification)Magnitude PhaseReflection uncertainty (specification)Magnitude Phase5Table 1-3 Corrected system performance with Type-N 50 Ω connectors, 85032F calibration kit, enhanced response calibrationNetwork analyzer: E5061A/E5062A, calibration kit: 85032F (Type-N, 50 Ω) calibration: enhanced responseIF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 °C ±5 °C with < 1 °C deviation from calibration temperature, isolation calibration not omittedDescription Specification (dB)300 kHz to 1.5 GHz1.5 to 3 GHzDirectivity 49 46Source match 41 40Load match 15 15 Reflection tracking ±0.011 ±0.021 Transmission tracking±0.015±0.018Transmission uncertainty (specification)Magnitude PhaseReflection uncertainty (specification)Magnitude Phase6Table 1-4 Corrected system performance with Type-N 75 Ω connectors 85036E calibration kit, full 2-port calibrationNetwork analyzer: E5061A/E5062A, calibration kit: 85036E (Type-N, 75 Ω), calibration: full 2-portIF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 °C ±5 °C with < 1 °C deviation from calibration temperature, isolation calibration not omittedDescription Specification (dB)300 kHz to 1.5 GHz1.5 to 3 GHzDirectivity 48 44Source match 41 35Load match 48 44 Reflection tracking ±0.010 ±0.019 Transmission tracking±0.015±0.029Transmission uncertainty (specification)Magnitude PhaseReflection uncertainty (specification)Magnitude Phase7Table 1-5 Corrected system performance with Type-N 75 Ω connectors 85036E calibration kit, enhanced response calibrationNetwork analyzer: E5061A/E5062A, calibration kit 85036E (Type-N, 75 Ω), calibration: enhanced response IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 °C ±5 °C with < 1 °C deviation from calibration temperature, isolation calibration not omittedDescription Specification (dB)300 kHz to 1.5 GHz1.5 to 3 GHzDirectivity 48 44Source match 41 35Load match 15 15 Reflection tracking ±0.010 ±0.019 Transmission tracking±0.015±0.029Transmission uncertainty (specification)Magnitude PhaseReflection uncertainty (specification)Magnitude Phase8Table 1-6 Uncorrected system performance(correction: off, 23 °C ±5 °C)Description Specification300 kHz to 3 GHzDirectivity 25 dB Source match 25 dB Load match 15 dB Transmission tracking ±1.0 dB Reflection tracking±1.0 dBTable 1-7Test port output frequencyDescription Specification TypicalRange E5061A 300 kHz to 1.5 GHz E5062A300 kHz to 3 GHzResolution 1 Hz Source stability E5061A/E5062A±5 ppm (5 °C to 40 °C)CW accuracy E5061A/E5062A±5 ppm, 23 °C ±5 °C Uncorrected system performanceTest port output (source)9Table 1-9Test port output signal purityDescription Specification Typical Harmonics (2nd or 3rd) 10 MHz to 2 GHz< –25 dBc (at 5 dBm)Non-harmonic spurious 10 MHz to 3 GHz< –30 dBc (at 0 dBm)Test port output (source)Table 1-8Test port output powerDescription Specification Typical Level accuracy (at 23 °C ±5 °C)1 300 kHz to 3 GHz ±0.8 dB (at 0 dBm, 50 MHz absolute) ±1.0 dB (at 0 dBm, relativeto 50 MHz reference)Level linearity (at 23°C ±5°C) 300 kHz to 3 GHz ±0.75 dB (at –5 to 10 dBm)Range (standard) 300 kHz to 3 GHz –5 to 10 dBm Range (extended power) 300 kHz to 3 GHz–45 to 10 dBm (non-harmonics spurious may limit power range)Sweep range (without extended power range) 300 kHz to 3 GHz–5 to 10 dBmLevel resolution 0.05 dBTest port output (source)1. Level accuracy for 75Ω analyzers is not a specification for frequencies >2 GHz; it is a typical characteristic.Test port inputTable 1-10 Test port input levelsDescription Specification Typical Maximum test port input level300 kHz to 3 GHz +10 dBmDamage level300 kHz to 3 GHz +20 dBm, ±30 VDC Crosstalk1300 kHz to 3 GHz –110 dBTable 1-11 Test port input (trace noise2)Description Specification TypicalTrace noise magnitude300 kHz to 1 MHz 8 mdB rms (23 °C ±5 °C)(source power level = +10 dBm)1 MHz to 3 GHz 5 mdB rms (23 °C ±5 °C)(source power level = +10 dBm)Trace noise phase300 kHz to 1 MHz 0.05° rms (23 °C ±5 °C)(source power level = +10 dBm)1 MHz to 3 GHz 0.03° rms (23 °C ±5 °C)(source power level = +10 dBm)Table 1-12 Test port input (stability 3)Description Specification TypicalStability magnitude3 MHz to 3 GHz 0.01 dB/°C(at 23 °C ±5 °C) Stability phase3 MHz to 3 GHz 0.1°/°C(at 23 °C ±5 °C)1. Response calibration not omitted.2. Trace noise is defined as a ratio measurement of a through, at IF bandwidth = 3 kHz.3. Stability is defined as a ratio measurement at the test port.10Table 1-13 Test port input (dynamic accuracy)Accuracy of the test port input power reading is relative to –10 dBm reference input power level.TypicalSpecification Magnitude PhaseTable 1-14 Test port input (group delay 1)informationDescription Specification Supplemental Aperture (selectable) (frequency span)/(number of points –1)Maximum aperture 25% of frequency spanMinimum delay Limited to measuring no more than180° of phase change within the minimum aperture. Accuracy See graph belowThe following graph shows group delay accuracy with Type-N full 2-port calibration and a 10 Hz IF bandwidth. Insertion loss is assumed to be < 2 dB. Group delay (typical)In general, the following formula can be used to determine the accuracy, in seconds, of specific group delay measurement:±phase accuracy (deg)/[360 x aperture (Hz)]1. Group delay is computed by measuring the phase change within a specified step (determined by thefrequency span and the number of points per sweep).General informationTable 1-15 System bandwidthscharacteristicsGeneral DescriptionIF bandwidth settingsRange 10 Hz to 30 kHzNominal settings are:10, 30, 100, 300, 1 k, 3 k, 10 k, 30 kTable 1-16 Front panel informationcharacteristicsDescriptionGeneral RF connectorsType Type-N, female; 50 Ω or 75 ΩDisplaySize 10.4 in TFT color LCDResolution VGA (640 x 480)11. Valid pixels are 99.99% and more. Below 0.01% of fixed points of black, blue, green or red arenot regarded as failure.Table 1-17 Rear panel informationcharacteristicsDescription GeneralExternal trigger connectorfemaleType BNC,Input level LOW threshold voltage: 0.5 VHIGH threshold voltage: 2.1 VInput level range: 0 to +5 VPulse width ≥ 2 µseconlyPolarity Negative(downward) External reference signal input connectorfemaleType BNC,Input frequency 10 MHz ±10 ppmInput level 0 dBm ±3 dBInternal reference signal output connectorfemaleType BNC,Output frequency 10 MHz ±10 ppmSignal type Sine waveOutput level 0 dBm ±3 dB into 50 ΩOutput impedance 50 ΩVGA video output15-pin mini D-Sub; female; drives VGA compatible monitorsGPIB24-pin D-Sub (type D-24), female; compatible with IEEE-488Parallel port36-pin D-Sub (type 1284-C), female; provides connection to printers, or multiportsettestUSB port Universal serial bus jack, type A configuration (4 contacts inline, contact 1 on left);female; provides connection to printer, ECal module, USB/GPIB interfaceContact 1 Vcc: 4.75 to 5.25 VDC, 500 mA, maximumContact 2 -DataContact 3 +DataContact 4 GroundLAN10/100 BaseT Ethernet, 8-pin configuration; auto selects between the two data rates Handler I/O port36-pin Centronics, female; provides connection to handler systemLine power1Frequency 47 Hz to 63 HzVoltage 90 to 132 VAC, or 198 to 264 VAC (automatically switched)VA max 350 VA max.1. A third-wire ground is required.Table 1-18 EMC and safetycharacteristicsDescription GeneralTable 1-19 Analyzer environment and dimensionscharacteristicsDescription General Operating environmentTemperature +5 °C to +40 °CError-corrected temperature range 23 °C ±5 °C with < 1 °C deviation from calibration temperature Humidity 20% to 80% at wet bulb temperature < +29 °C (non-condensing) Altitude 0 to 2,000 m (0 to 6,561 feet)Vibration 0.5 G maximum, 5 Hz to 500 HzNon-operating storage environmentTemperature –10 °C to +60 °CHumidity 20% to 90% at wet bulb temperature < 40 °C (non-condensing) Altitude 0 to 4,572 m (0 to 15,000 feet)Vibration 0.5 G maximum, 5 Hz to 500 HzDimensions See figure 1-1 through figure 1-3.Weight 13.5 kgFigure 1-2. Dimensions (front view, in millimeters)Figure 1-3. Dimensions (rear view, in millimeters)Figure 1-4. Dimensions (side view, in millimeters)Table 1-20Typical cycle time for measurement completion 1 (ms) (Display update: off) Number of points51 201 401 1601Start 1 GHz, stop 1.2 GHz, 30 kHz IF bandwidthUncorrected 8 19 33 1172-port cal 14 35 63 230Start 300 kHz, stop 1.5 GHz, 30 kHz IF bandwidthUncorrected 15 25 39 1232-port cal 27 48 75 243Start 300 kHz, stop 3 GHz, 30 kHz IF bandwidthUncorrected 17 28 41 1252-port cal 31 53 80 247Measurement throughput summary1. Typical performance.Table 1-21Typical cycle time for measurement completion 1 (ms) (Display update: on) Number of points51 201 401 1601Start 1 GHz, stop 1.2 GHz, 30 kHz IF bandwidthUncorrected 59 68 83 1722-port cal 85 103 131 304Start 300 kHz, stop 1.5 GHz, 30 kHz IF bandwidthUncorrected 64 74 89 1782-port cal 95 116 144 317Start 300 kHz, stop 3 GHz, 30 kHz IF bandwidthUncorrected 66 78 91 1802-port cal 98 121 148 322Table 1-22 Data transfer time1 (ms)Number of points401160120151SCPI over GPIB2REAL 64 6 14 25 89ASCII 513831522193SCPI over 100 Mbps LAN (telnet)2REAL 64 3 3 4 62040510 ASCII 92354SCPI over 100 Mbps LAN (SICL-LAN)2REAL 64 7 7 8 121273421ASCII 9COM (program executed in the analyzer)2Variant type 2 2 2 21. Typical performance.2. Measured using a VEE 6.01 program running on a 500 MHz Pentium® III Dell Optiplex, Transferredcomplex S11 data, using :CALC:DATA?SDATA.Measurement capabilitiesNumber of measurement channels Up to 4 independent measurement channels. A measurement channel is coupledto stimulus response settings including frequency, IF bandwidth, power level,and number of points.Number of display windows Each measurement channel has a display window. Up to 4 display windows (channels)can be displayed.Number of traces 4 data traces and 4 memory traces per channelMeasurement choices Option E5061A/E5062A-150/175: S11, S21Option E5061A/E5062A-250/275: S11, S21, S12, S22Measurement parameter conversion Available to convert S-parameters into reflection impedance, transmission impedance,reflection admittance, transmission admittance, and 1/S.Data formats Log magnitude, linear magnitude, phase, expanded phase, positive phase,group delay, SWR, real, imaginary, Smith chart, polar.Data markers 10 independent markers per trace. Reference marker availablefor delta marker operation. Smith chart format includes 5 marker formats:linear magnitude/phase, log magnitude/phase, real/imaginary,R + jX, and G + jB. Polar chart format includes 3 marker formats:linear magnitude/phase, log magnitude/phase, and real/imaginary.Marker functionsMarker search Max value, min value, multi-peak, multi-target, peak, peak left, peak right, target,target left, target right, and width parameters with user-defined bandwidth values. Marker-to functions Set start, stop, center to active marker stimulus value; set reference to activemarker response value; set electrical delay to group delay at active marker.Search range User definable.Tracking Performs marker search continuously or on demand.Fault location functions (Option E5061A/E5062A-100)Transformation to distance and time domain Selectable transformation type from bandpass, lowpass impulse, lowpass step.Selectable window from maximum, normal and minimum.LXI compliance Class C (only applies to units that are shipped with firmware revision A.03.00 or later).Source controlMeasured number of points per sweep User definable from 2 to 1601.Sweep type Linear sweep, segment sweep, log sweep and power sweep.Segment sweep Define independent sweep segments. Set number of points, test port power levels,IF bandwidth, delay time, sweep time and sweep mode independently for each segment. Sweep trigger Set to continuous, hold, or single, sweep with internal, external, manual,or bus trigger.Power Set source power from -5 dBm (-45 dBm for option E5061A/E5062A-1E1/250/275)to 10 dBm. The power slope function compensates source power level error.Trace functionsDisplay data Display current measurement data, memory data,or current measurement and memory data simultaneously.Trace math Vector addition, subtraction, multiplication or division ofmeasured complex values and memory data.Title Add custom title to each channel window. Titles areprinted on hardcopies of displayed measurements.Autoscale Automatically selects scale resolution and reference value tovertically center the trace.Electrical delay Offset measured phase or group delay by a defined amount ofelectrical delay, in seconds.Phase offset Offset measured phase or group delay by a defined amount in degrees. Statistics Calculates and displays mean, standard deviation and peak-to-peakdeviation of the data trace.Data accuracy enhancementMeasurement calibration Measurement calibration significantly reduces measurementuncertainty due to errors caused by system directivity, source andload match, tracking and crosstalk. Full 2-port calibrationremoves all the systematic errors for the related test ports to obtainthe most accurate measurements.Calibration types availableResponse Simultaneous magnitude and phase correction of frequency responseerrors for either reflection or transmission measurements.Response and isolation Compensates for frequency response and crosstalk errors oftransmission measurements.Enhanced response Compensates for frequency response and source match errorsOne-port calibration Compensates for directivity, frequency response and source match errors.Full 2-port calibration (Option E5061A/E5062A-250/275) Compensates for directivity, source match, reflection tracking, load match,transmission tracking and crosstalk. Crosstalk calibration can be omitted. Interpolated error correction With any type of accuracy enhancement applied, interpolated moderecalculates the error coefficients when the test frequencies are changed.The number of points can be increased or decreased and the start/stopfrequencies can be changed.Velocity factor Enter the velocity factor to calculate the equivalent physical length. Reference port extension Redefine the measurement plane from the plane where the calibration was done.21StorageInternal hard disk drive Store and recall instrument states, calibration data, and trace dataon 10 GB, minimum, internal hard drive. Trace data can be saved in CSV(comma separated value) format. All files are MS-DOS ®-compatible.Instrument states include all control settings, limit lines, segment sweeptables, and memory trace data.File sharing Internal hard disk drive (D:) can be accessed from an externalWindows® PC through LAN.Disk drive Instrument states, calibration data, and trace data can be stored onan internal 3.5 inch 1.4 MB floppy disk in MS-DOS ®-compatible format. Screen hardcopy Printouts of instrument data are directly produced on a printer. The analyzerprovides USB and parallel interfaces.System capabilitiesFamiliar graphical user interface The ENA-L analyzer employs a graphical user interface based onWindows® operating system. There are three ways to operate the instrumentmanually: you can use a hardkey interface, touch screen interface (optionE5061A/E5062A-016) or a mouse interface.Limit lines Define the test limit lines that appear on the display for pass/fail testing.Defined limits may be any combination of horizontal/sloping lines and discretedata points.22AutomationGPIB InternalSCPI X XCOM XMethodsInternal analyzer execution Applications can be developed in a built-in VBA® (Visual Basic for Applications)language. Applications can be executed from within the analyzer via COM(component object model) or using SCPI.Controlling via GPIB The GPIB interface operates to IEEE 488.2 and SCPI protocols.The analyzer can be controlled by a GPIB external controller. The analyzer cancontrol external devices using a USB/GPIB interface.LANStandard conformity 10 BaseT or 100 BaseTX (automatically switched), Ethertwist,RJ45 connectorProtocol TCP/IPFunction Telnet, SICL-LANWeb ResourcesFor additional literature and productinformation about the Agilent ENA-L visit:/find/ena23Microsoft ®, Windows ® and Visual Basic ® are U.S. registered trademarks of Microsoft Corporation.Pentium ® is a US registered trademarks of Intel Corporation.Revised: July 2, 2009Product specifications and descriptions in this document subject to change without notice.© Agilent Technologies, Inc. 2009Printed in USA, September 18, 20095989-0018EN。
伊顿 ADE-1FC 非铠装电缆接头 数据表
US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2019 Eaton2061G 1ADE-1FC non-armoredcable glandsADE-1FC cable glands are designed to provide a flameproof andweatherproof seal on the outer sheath of non-armored, tray, marineshipboard or Type P cable. ADE glands are available in a wide rangeof materials to suit any application.Features:Standard materials:IECEx/ATEXNEMA 4XIP66/IP68Cable types:•Non-armored and tray cable – TC, TC-ER (HL)•Marine shipboard cable; Type P cable Unarmoured / Tray CableSteel/Copperwire braidedcableLead sheathedearthing washer)Metal-clad (interlocked andcorrugated armoured) cableOther certifications:•CEPEL 05.0558X•CCoE P360379-1•KOSHA 2015-BO-0479 to 0482•NANIO TC-RU C-FR.ГБ05.B.00858•NEPSI GYJ13.1082XShipping application:•ABS 14-HS1274083-PDA•BV 40910/A0 BV•DNV TAE000010X•Lloyds 11/00072•DTS-01:1991FeatuA Specifically formulated elastomer – provides IP sealing onouter sheath of the cableoutB Barrier compound chamber – seals conductors forexplosionproof applications with use of TSC compound barriersealseaDeluge seal – additional protection against moisture ingressC DelD Optional external clamp – provides additional external strainrelief for rugged applicationsOperating temperatures:For all certificates (excluding UL E324850): -60°C to +80°C•For UL certificate E324850: -25°C to +40°CACBD ATEX Certificate No.: INERIS12ATEX0032XZones 1 & 2, Groups IIA, IIB, IICZones 21 & 22, Groups IIIA, IIIB, IIICIM2 / Ex db I / Ex eb I; for mining applications: brass, stainlesssteel or bronze – ADE sizes 11 to 16, 2” to 4” NPT, ISO 63 to 110•Zones 21 & 22, Groups IIIA, IIIB, IIIC•Ex db IIC / Ex eb IIC / Ex nRc IIC / Ex tb IIICEx db I / Ex eb I; for mining applications: brass, stainless steel orbronze – ADE sizes 11 to 16, 2” to 4” NPT, ISO 63 to 110UL certifications:3DJN E310130, Class I, Zone 2A, AEx de II, Ex de II• ADE sizes 4 to 16, 1/2” to 4” NPT or ISO 20 to 110 with non-armored cable types ITC, MV, PLTC, TC-ER, TC-ER-HL, TC andTSC epoxy sealing compound3DJN E310130, Class I, Division 1, Groups A, B, C, D• ADE sizes 4 to 9, 1/2” to 11/4” NPT or ISO 20 to 40 with non-armored cable type TC-ER-HL and TSC epoxy sealing compound3DJN E310130, Class I, Division 2, Groups A, B, C, D” to 4” NPT or ISO 20 to 110 with non-armored cable types PLTC, PLTC-ER, ITC, ITC-ER, ITC-HL, TC,4EC5 E324850, Class I, Division 2, Groups A, B, C, D• ADE sizes 4 to 16, 1/2” to 4” NPT or ISO 20 to 110 with non-armored marine cable and TSC epoxy sealing compoundprovides 100% of cable clampingA Can be used in Division 2, provided that the enclosure contains no components that produce arcs or sparks. US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2019 Eaton2071GADE-1FC non-armored cable glandsIECEx/ATEX NEMA 4X IP66/IP68Catalog numbers are for nickel-plated brass; refer to part number builder above for other options.Dimensions shown in inches (millimeters).Ordering information:Part number exampleADE1CM253NPSCNK1B Not UL certified.NPT thread sizeCat. # NPTMetric thread sizeCat. # MetricABNPT threads (C)Metric threads (C)D EMax. no. of coresGland sizeMin.Max.3/”B ADE1CN0383NPSCN M16ADE1CM163NPSCN 0.16 (4.0)0.33 (8.0)0.75 (19.0)0.59 (15.0)0.65 (16.6)0.59 (15.0) 1.42 (36.0)0.26 (6.5)64。
Eaton CDAP-01 xx-1E智能调光插座数据手册说明书
Dimming Plug 230VAC / 250W CDAP-01/xx-1ET echnical Data / T echnische gegevens / T ekniske data /T echnische Daten / T echnická dataPower supply 230 VAC +10% -15%, 50 Hz Power standby 280mW (TYP)Load R,L,C: 0 - 250 W (0 - 250 VA) (at 45°C, Derating*)LED, ESL: 0 - 100 W (TYP)**Technology Eaton Smart Dimming technology with overload protection. Auto trailing / leading edge mode. EMS 0.5 W to 250 W, 5% ±0.5 W (>0.5 W)RF868,3MHz (xComfort compatible)Button Operation On / Off / DimButton LED Multi-Color EMS power consumption Profiles 6 Dimming ProfilesDimensions 100.3 x 52 x 56.9 mm (H x W x D)** Depending on the lamp type.Instruction Leaflet Montageanweisung Notice d’installation Instrucciones de montaje Istruzioni per il montaggioИнструкцияпомонтажуȈᬩMontagehandleiding Montagevejledning ΟδηγίεςεγκατάστασηςInstruções de montagem Monteringsanvisning Asennusohje Návod k montážiPaigaldusjuhend Szerelési utasítás Montāžas instrukcija Montavimo instrukcija Instrukcja montażu Navodila za montažo Návod na montážМонтажниинструкцииInstrucţiuni de montaj Upute za montažu Kullanma TalimatıУпутствоIntruksjonsbladМонтажнаінструкціяEU- type examination performed by: TÜV Austria Services GmbH, Notified Body 1230 Vienna, Deutschstrasse 10, Austria Affixing date of CE mark: 2018Doc.Id.: CDAP-01xx-1E_270718Senior Vice President Director Quality General Manager & Systems Friedrich Schröder Fernando Ceccarelli We, EATON Industries (Austria) GmbH3943 Schrems, Eugenia 1Austriadeclare under our sole responsibility as the manufacturer that the product (family)Eaton - Plug in adapter - dimming, CDAP-01/xx-1E (the declaration of conformity applies to all listed types within our actual product catalogue) provided that it is installed, maintained and used in the application intended for, with respect to the relevant manufacturers instructions, installation standards and “good engineering practices” complies with the provisions of Council directive(s):RED Directive 2014/53/EURoHS Directive 2011/65/EUbased on compliance with following standard(s):EN 301489-3 V2.1.1, EN 300220-2 V3.1.1, EN 50491-5-1:2010, EN50491-5-2:2010, EN 62479:2010, EN 50428:2005 + A1:2007 + A2:2009,EN 55015:2013, EN 61547:2009, IEC 60884-2-5:1995, EN 50581:201227.07.2018。
AWE1611功率分析仪
功率计说明书/User manual交直流通用功率分析仪AWE1611系列台式功率计Evision beta 1.0 AUG 28, 2015Website: http://www.aitek.twEmail: sales@aitek.tw手册内容为试用版，有可能存在错漏，或因技术升级而变更，恕不另行通知。
本产品的名称也可以为：电参数测量仪，电参数测试仪、功率测量仪、功率分析仪等。
开卷致谢感谢您购买AWE1611系列功率分析仪，为了最大限度地发挥分析仪的功能，请首先仔细阅读本使用手册，并留用随时查阅。
该产品具有众多的测量功能。
仪器属于台式仪器，具备六数码管窗口参数显示功能，并且可通过其他的系统显示测量参数，如Windows系统。
我们已经努力使本手册达到尽善尽美，但很可能仍有某些部分阐述不清，希望您能通过我们的代理商转告或直接致电给我们，在此先表示感谢。
开箱说明打开包装时，首先检查确认仪器在运输过程中没有损坏，特别是检查一下附件、面板开关和接头。
仪器若有损坏或按照说明不能操作，与经销商或直接致电AITEK联系。
包装包括以下主机和附件，请你认真核对：校验及校正声明AITEK特别声明，本手册所列的仪器设备完全符合本公司一般手册上所标称的规范和特性。
本仪器在出厂前已经通过本公司的厂内校验。
本公司校验用的所有仪器设备都已委请技术监督部门认可的检验中心作定期校正，校验的程序和步骤是符合电子检验中心的规范和标准。
产品质量保证AITEK保证所生产制造的新品仪器均经过严格的质量确认，同时保证在出厂一年内，如有发现产品的施工瑕疵或零件故障，本公司负责免费给予修复。
但是如果使用者有自行更改电路、功能、或自行修理仪器及零件或外壳损坏等情况，本公司不提供免费保修服务，得视实际状况收取维修费用。
如果未按照规定将所有地线接妥或未按照安全规范操作机器而发生异常状况，本公司恕不提供免费保修服务。
本保证不含本机器的附属设备等非AITEK所生产的附件。
IEC601~1
Typ B F N .C . 0 ,5 S .F .C . 11)
Typ C F N .C . 0 ,5 S .F .C . 11)
S .F .C . 11)
2 ,5
51)
2 ,5
51)
2 ,5
51)
5
101)
5
101)
5
101)
0 ,1
0 ,5
0 ,1
0 ,5
Application of electrical current directly to the human body
Special environmental conditions
Annex A of EN 60601-1
1
Comparison between EN60601 & EN60950 Paul Hung September 2000
EN 60601-1 Cl.2.1.5
4
Comparison between EN60601 & EN60950 Paul Hung September 2000
Limitation of Voltage and Energy / Discharge Test
EN 60601 Voltage 60V after 1s EN 60950 (37% of V 0 ) 1s (Pluggable type A) 10s (Pluggable type B) max. capacitance between L/N and enclosure (w/o testing) interference suppression capacitor < 3000pF (250V) < 5000pF (125V) interference suppression capacitor < 0.1 F interference suppression capacitor
电器渠道_Eaton DE1变速启动器说明书
Eaton 174340Eaton DE1 Variable speed starter, Rated operational voltage 400 V AC, 3-phase, Ie 16 A, 7.5 kW, 10 HP, Radio interference suppression filterGeneral specificationsEaton DE1 Variable speed starter 174340DE1-34016FN-N20N 4015081708024169 mm 230 mm 90 mm 1.6 kg Certified by UL for use in Canada UL File No.: E172143 CSA-C22.2 No. 14Specification for general requirements: IEC/EN 61800-2 IEC/EN61800-5 RoHS, ISO 9001 UL UL 508C CEUL report applies to both US and Canada CULIEC/EN 61800-3 RCMUL Category Control No.: NMMS, NMMS7Safety requirements: IEC/EN 61800-5-1Overload cycle for 60 s every 600 sProduct NameCatalog Number Model CodeEANProduct Length/Depth Product Height Product Width Product Weight CertificationsCatalog Notes480 V16 A14 AIs the panel builder's responsibility. The specifications for the switchgear must be observed.400 V AC, 3-phase480 V AC, 3-phaseMeets the product standard's requirements.7.5 kW500 VMeets the product standard's requirements.-40 °C380 VPC connectionRadio interference suppression filter0 Hz50 °C200 %, IH, max. starting current (High Overload), For 1.875 seconds every 600 seconds, Power section15.2 A I/O ConfigurationUpdate DX-COM-STICK3DX-COM-STICK3_ConnectionSet point settingHow does the internal motor protection work?Quick-Start-Guide DE11 (english)Motor data Motor Protection V/f curves Slip Compensation Starting, Stopping and OperationElectromagnetic compatibility (EMC)The OP System Bus - Parameterizing - ControlConformal CoatingConnecting drives to generator suppliesAccess to Parameter Level 2 Parameter Lock Load DefaultFire modeQuick-Start-Guide DE1 (english)Number 1 in efficiency The easiest way of variable motor speed PowerXL DE1 Variable Speed StarterHVAC, water/wastewater and industrial mediums - brochureProduct Range Catalog Drives EngineeringDrives - Product range catalogDA-DC-00004551.pdfDA-DC-00004556.pdfeaton-frequency-inverter-dimensions-010.epseaton-frequency-inverter-3d-drawing-018.epsIL040005ZUPowerXL DE1 variable speed starterMN040018_ENMN040011_ENMains voltage - maxRated operational current for specified heat dissipation (In) Assigned motor current IM at 440 - 480 V, 60 Hz, 150% overload 10.11 Short-circuit ratingRated operational voltage10.4 Clearances and creepage distancesOutput at quadratic load at rated output voltage - maxOutput voltage - max10.2.3.1 Verification of thermal stability of enclosuresAmbient storage temperature - minMains voltage - minFitted with:Output frequency - minAmbient operating temperature at 150% overload - max Starting current - maxAssigned motor current IM at 230 V, 50 Hz, 150% overload Application notesBrochuresCatalogsCertification reports DrawingsInstallation instructions Installation videos Manuals and user guides60 °CModbus RTU, built inOP-Bus (RS485), built in10 HP300 Hz400 V AC, 3-phase480 V AC, 3-phase16 kHz, 4 - 32 kHz adjustable (audible), fPWM, Power section, Main circuitParameterization: drivesConnectParameterization: drivesConnect mobile (App) Parameterization: FieldbusParameterization: Keypad-10 °C≤ 0.6 A (max. 6 A for 120 ms), Actuator for external motor brakeDoes not apply, since the entire switchgear needs to be evaluated.16 A14 ADoes not apply, since the entire switchgear needs to be evaluated.Does not apply, since the entire switchgear needs to be MZ040046_ENMN040003_ENDA-CD-de1_fs2_ip20 DA-CS-de1_fs2_ip20Ambient operating temperature - maxCommunication interfaceAssigned motor power at 115/120 V, 60 Hz, 1-phaseOutput frequency - maxOutput voltage (U2)Switching frequencyFeaturesAmbient operating temperature - minBraking currentNumber of HW-interfaces (serial TTY)10.6 Incorporation of switching devices and componentsNominal output current I2NAssigned motor current IM at 220 - 240 V, 60 Hz, 150% overload10.2.6 Mechanical impact10.3 Degree of protection of assembliesmCAD modelevaluated.Assigned motor current IM at 115 V, 50 Hz, 150% overload 15.2 AProduct categoryVariable speed starterRadio interference classC2, C3: depending on the motor cable length, the connected load, and ambient conditions. External radio interference suppression filters (optional) may be necessary.Optional external radio interference suppression filter for longer motor cable lengths and for use in different EMC environmentsAssigned motor current IM at 110/120 V, 60 Hz, 150% overload 14 AHeat dissipation capacity Pdiss0 WAssigned motor power at 460/480 V, 60 Hz, 3-phase10 HPNumber of HW-interfaces (RS-422)Mains current distortion120 %ProtocolMODBUSEtherNet/IPOther bus systems10.9.2 Power-frequency electric strengthIs the panel builder's responsibility.Overvoltage categoryIIIDegree of protectionIP20NEMA OtherAmbient storage temperature - max70 °CRated impulse withstand voltage (Uimp)2000 VOutput at linear load at rated output voltage - max7.5 kWLeakage current at ground IPE - max< 3.5 mA (AC-operated)< 10 mA (DC-operated)Converter typeU converterFrame sizeFS210.2.2 Corrosion resistanceMeets the product standard's requirements.Supply frequency50/60 Hz10.2.4 Resistance to ultra-violet (UV) radiationMeets the product standard's requirements.10.2.7 InscriptionsMeets the product standard's requirements.Shock resistance15 g, Mechanical, According to IEC/EN 60068-2-27, 11 msApplication in domestic and commercial area permittedYesApparent power at 480 V13.3 kVANumber of inputs (analog)1 (parameterizable, 0 - 10 V DC, 0/4 - 20 mA)Number of phases (output)3Apparent power at 400 V11.09 kVA10.12 Electromagnetic compatibilityIs the panel builder's responsibility. The specifications for the switchgear must be observed.10.2.5 LiftingDoes not apply, since the entire switchgear needs to be evaluated.Number of HW-interfaces (RS-485)1Number of HW-interfaces (industrial ethernet)10.8 Connections for external conductorsIs the panel builder's responsibility.ProtectionFinger and back-of-hand proof, Protection against direct contact (BGV A3, VBG4)Number of relay outputs1 (parameterizable, N/O, 6 A (250 V, AC-1) / 5 A (30 V, DC-1))Application in industrial area permittedYesClimatic proofing< 95 average relative humidity (RH), no condensation, no corrosionConnection to SmartWire-DTIn conjunction with DX-NET-SWD3 SmartWire DT moduleYesStatic heat dissipation, non-current-dependent Pvs0 W10.9.3 Impulse withstand voltageIs the panel builder's responsibility.Voltage rating - max480 VOverload current IL at 150% overload24 AInput current ILN at 150% overload16.5 ANumber of HW-interfaces (RS-232)Number of inputs (digital)4 (parameterizable, 10 - 30 V DC)Rated control supply voltage10 V DC (Us, max. 0.2 mA)Cable lengthC2 ≤ 10 m, Radio interference level, maximum motor cable lengthC3 ≤ 25 m, Radio interference level, maximum motor cable length10.5 Protection against electric shockDoes not apply, since the entire switchgear needs to be evaluated.Mounting positionVerticalMains switch-on frequencyMaximum of one time every 30 seconds10.13 Mechanical functionThe device meets the requirements, provided the information in the instruction leaflet (IL) is observed.10.9.4 Testing of enclosures made of insulating materialIs the panel builder's responsibility.Heat dissipation per pole, current-dependent Pvid0 WElectromagnetic compatibility1st and 2nd environments (according to EN 61800-3)Resolution0.025 Hz (Frequency resolution, setpoint value)Assigned motor power at 460/480 V, 60 Hz10 HPRelative symmetric net voltage tolerance10 %Equipment heat dissipation, current-dependent Pvid240 WRated operational current (Ie)16 A at 150% overload (at an operating frequency of 16 kHz and an ambient air temperature of +50 °C)Number of outputs (analog)Suitable forBranch circuits, (UL/CSA)Rated operational power at 380/400 V, 50 Hz, 3-phase7.5 kWNumber of HW-interfaces (USB)Operating modeU/f controlSpeed control with slip compensationRated frequency - min45 HzDelay time< 10 ms, On-delay< 10 ms, Off-delayNumber of outputs (digital)Power consumption240W10.2.3.2 Verification of resistance of insulating materials to normal heatMeets the product standard's requirements.10.2.3.3 Resist. of insul. mat. to abnormal heat/fire by internal elect. effectsMeets the product standard's requirements.Number of HW-interfaces (other)Rated frequency - max66 HzVibrationResistance: According to EN 61800-5-1Short-circuit protection (external output circuits)Type 1 coordination via the power bus' feeder unit, Main circuit10.7 Internal electrical circuits and connectionsIs the panel builder's responsibility.Braking torqueMax. 30 % MN, Standard - Main circuitAdjustable to 100 %, DC - Main circuitAmbient operating temperature at 150% overload - min-10 °CRelative symmetric net frequency tolerance10 %10.10 Temperature riseThe panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.Assigned motor current IM at 400 V, 50 Hz, 150% overload 15.2 AAmbient operating temperature detailsDerating between 50 °C and60 °C:None if fPWM ≤ 14 kHzup to a max. of 50 °CNone if fPWM ≤ 16 kHzup to a max. of 46 °CNone if Iₑ ≤ 10.6 A andfPWM ≤ 20 kHzNone if Iₑ ≤ 14.9 A andfPWM ≤ 10 kHzNumber of HW-interfaces (parallel)Assigned motor power at 230/240 V, 60 Hz, 1-phase10 HPNumber of phases (input)3Heat dissipation at current/speed116 W at 50% current and 0% speed121 W at 50% current and 50% speed126 W at 50% current and 90% speed180 W at 100% current and 0% speed198 W at 100% current and 50% speed216 W at 100% current and 90% speed78 W at 25% current and 0% speed86 W at 25% current and 50% speedShort-circuit protection rating25 A, UL (Class CC or J), Safety device (fuse or miniature circuit-breaker), Power WiringNumber of interfaces (PROFINET)AltitudeAbove 1000 m with 1 % derating per 100 mMax. 2000 mEaton Corporation plc Eaton House30 Pembroke Road Dublin 4, Ireland © 2023 Eaton. All Rights Reserved. Eaton is a registered trademark.All other trademarks areproperty of their respectiveowners./socialmedia。