CTEP125U-0R6M中文资料
DS91M125 125 MHz 1 4 M-LVDS Repeater with LVDS Inp
DS91M125 125 MHz 1:4 M-LVDS Repeater withLVDS Input Evaluation KitUSER MANUALPart Number: DS91M125EVK NOPBFor the latest documents concerning these products and evaluation kit, visit . Schematics andgerber files are also available at OverviewThe purpose of this document is to familiarize you with the DS91M125 evaluation board, suggest the test setup procedures and instrumentation, and to guide you through some typical measurements that will demonstrate the performance of the device. The board enables the user to examine performance and all functions of theDS91M125 as a standalone device.The DS91M125 is a high-speed 1:4 M-LVDS repeater with an LVDS input designed for multipoint applications with multiple drivers or receivers. The device conforms to TIA/EIA-899 standard. It utilizes M-LVDS technology for low power, high-speed and superior noise immunity.DescriptionFigure 1 below represents the top layer drawing of the board with the silkscreen annotations. It is a 2.5 x 3 inch 4 layer printed circuit board (PCB) that features a single DS91M125 (U2) device.Figure 1 -DS91M125EVK Top View DrawingDS91M125 Evaluation in a Point-to-Point LinkThe following is a recommended procedure for using and evaluating the DS91M125EVK. Figure 2 depicts a typical setup and instrumentation used.1. Select a single DS91M125 evaluation board.2. Apply the power to the board (3.3 V typical) between J3 and J4 power tabs, observe the value of I CC,and compare it with the expected value (refer to the datasheet) to ensure that the devices arefunctional.3. Enable one of the U2 driver outputs. This is accomplished by setting the DE0-3 pin to VDD (JP3-6).4. Connect a signal source to the driver input (DI+, DI-). The signal needs to be an LVDS/M-LVDS/CML/LVPECL compliant signal. Refer to the DS91M125 datasheet for the receiver inputcompatibility.5. Connect one of the U2 outputs (A0-3/B0-3) to an oscilloscope and observe the waveforms.Figure 2 – DS91M125 Test SetupFigure 3 shows an eye diagram acquired at the output of the DS91M125 driver loaded with a 100-ohm resistor. The generator connected to the driver input simulated a 100 Mbps PRBS-7 NRZ.Figure 3 – DS91M125 OutputIMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries(TI)reserve the right to make corrections,modifications,enhancements,improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty.Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty.Except where mandated by government requirements,testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design.Customers are responsible for their products and applications using TI components.To minimize the risks associated with customer products and applications,customers should provide adequate design and operating safeguards.TI does not warrant or represent that any license,either express or implied,is granted under any TI patent right,copyright,mask work right, or other TI intellectual property right relating to any combination,machine,or process in which TI products or services are rmation published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement e of such information may require a license from a third party under the patents or other intellectual property of the third party,or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties,conditions,limitations,and notices.Reproduction of this information with alteration is an unfair and deceptive business practice.TI is not responsible or liable for such altered rmation of third parties may be subject to additional restrictions.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications(such as life support)where a failure of the TI product would reasonably be expected to cause severe personal injury or death,unless officers of the parties have executed an agreement specifically governing such use.Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications,and acknowledge and agree that they are solely responsible for all legal,regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications,notwithstanding any applications-related information or support that may be provided by TI.Further,Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or"enhanced plastic."Only products designated by TI as military-grade meet military specifications.Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk,and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS16949requirements.Buyers acknowledge and agree that,if they use any non-designated products in automotive applications,TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAudio /audio Automotive and Transportation /automotiveAmplifiers Communications and Telecom /communicationsData Converters Computers and Peripherals /computersDLP®Products Consumer Electronics /consumer-appsDSP Energy and Lighting /energyClocks and Timers /clocks Industrial /industrialInterface Medical /medicalLogic Security /securityPower Mgmt Space,Avionics and Defense /space-avionics-defense Microcontrollers Video and Imaging /videoRFID OMAP Mobile Processors /omapWireless Connectivity /wirelessconnectivityTI E2E Community Home Page Mailing Address:Texas Instruments,Post Office Box655303,Dallas,Texas75265Copyright©2012,Texas Instruments Incorporated。
NTE0505M中文资料
Reflected Ripple Current
TYP 3.30
5 12 30
MAX Units 3.63 5.5 V 13.2
47 mA p-p
OUTPUT CHARACTERISTICS
Parameter
Conditions
Rated Power2
Voltage Set Point Accuracy
元器件交易网
NTE SERIES
Isolated 1W Single Output SM DC-DC Converters
FEATURES s Wide Temperature Performance at
Full 1 Watt Load, –40°C to 85°C s Lead Frame Technology s CECC00802 Reflow (280°C) s Single Isolated Output s 1kVDC Isolation s Efficiency to 78% s Power Density 1.8W/cm3 s 3.3V, 5V & 12V Input s 3.3V, 5V, 9V, 12V and 15V Output s Footprint Over Pins 1.64cm 2 s UL 94V-0 Package Material s No Heatsink Required s Internal SMD Construction s Toroidal Magnetics s Plastic Encapsulated s MTTF up to 2.9 Million Hours s Custom Solutions Available s Multi Layer Ceramic Capacitors s Lead Free Compatible
6MBI225U-120中文资料
6MBI225U-1201200V / 225A 6 in one-packageFeatures· High speed switching· Voltage drive· Low inductance module structureApplications · Inverter for Motor drive· AC and DC Servo drive amplifierMaximum ratings and characteristicsThermal resistance characteristicsThermal resistanceContact Thermal resistance––0.12––0.20–0.0167 –IGBTFWDWith thermal compound°C/W°C/W°C/W*2 : Two thermistor terminals should be connected together, each other terminals should be connected together and shortedto base plate when isolation test will be done.*3 :Recommendable value : 2.5 to 3.5 N·m(M5) *4 :Recommendable value : 3.5 to 4.5 N·m(M6)Rth(j-c)Rth(j-c)Rth(c-f)*5IGBT Module U-Series*5 : This is the value which is defined mounting on the additional cooling fin with thermal compound.4Items Symbols Conditions Characteristics UnitMin.Typ. Max.· Uninterruptible power supply· Industrial machines, such as Welding machinesCharacteristics (Representative)VGE=0V, f= 1MHz, Tj= 25°CVcc=600V, I=225A, Tj= 25°CCollector current vs. Collector-Emitter voltage (typ.)Tj= 125°C / chipCapacitance vs. Collector-Emitter voltage (typ.)Dynamic Gate charge (typ.)Collector current vs. Collector-Emitter voltage (typ.)Tj= 25°C / chipCollector current vs. Collector-Emitter voltage (typ.)VGE=15V / chipTj=25°C / chipCollector-Emitter voltage vs. Gate-Emitter voltage (typ.)010020030040050060012345C o l l e c t o r c u r r e n t : I c [A ]VGE=20V15V12V10V8V010020030040050060012345C o l l e c t o r c u r r e n t : I c [A ]VGE=20V 15V12V10V8V010020030040050060001234C o l l e c t o r c u r r e n t : I c [A ]Tj=125°CTj=25°C246810510152025C o l l e c t o r - E m i t t e r v o l t a g e : V C E [ V ]Ic=450A Ic=225A Ic= 112.5A0.11.010.0100.0102030C a p a c i t a n c e : C i e s , C o e s , C r e s [ n F ]200400600800100012001400C o l l e c t o r -E m i t t e r v o l t a g e : V C E [ 200V /d i v ]G a t e - E m i t t e r v o l t a g e : V G E [ 5V /d i v]Vcc=600V, Ic=225A, VGE=±15V, Tj= 25°CStray inductance <= 100nHSwitching loss vs. Collector current (typ.)Vcc=600V, VGE=±15V, Rg=3ΩVcc=600V, Ic=225A, VGE=±15V, Tj= 125°C+VGE=15V,-VGE <= 15V, RG >= 3Ω ,Tj <= 125°CSwitching time vs. Collector current (typ.)Vcc=600V, VGE=±15V, Rg=3Ω, Tj=125°CSwitching time vs. Gate resistance (typ.)Switching time vs. Collector current (typ.)Vcc=600V, VGE=±15V, Rg=3Ω, Tj= 25°CReverse bias safe operating area (max.)Switching loss vs. Gate resistance (typ.)10100100010000100200300400S w i t c h i n g t i m e : t o n , t r , t o f f , t f [ n s e c ]Collector current : Ic [ A ]10100100010000100200300400S w i t c h i n g t i m e : t o n , t r , t o f f , t f [ n s e c ]Collector current : Ic [ A ]10100100010000110100S w i t c h i n g t i m e : t o n , t r , t o f f , t f [ n s e c ]Gate resistance : Rg [ Ω ]trtftoffton 01020304050100200300400500S w i t c h i n g l o s s : E o n , E o f f , E r r [ m J /p u l s e ]Collector current : Ic [ A ]Eon(125°C)Eon(25°C)Eoff(125°C)Err(125°C)Err(25°C)Eoff(25°C)0255075100125150110100S w i t c h i n g l o s s : E o n , E o f f , E r r [ m J /p u l s e ]Gate resistance : Rg [ Ω ]EoffErrEon0100200300400500600200400600800100012001400C o l l e c t o r c u r r e n t : I c [ A ]Collector - Emitter voltage : VCE [ V ]Transient thermal resistance (max.)Reverse recovery characteristics (typ.)Vcc=600V, VGE=±15V, Rg=3ΩForward current vs. Forward on voltage (typ.)chipTemperature characteristic (typ.)01002003004005006001234F o r w a r d c u r r e n t : I F [ A ]Forward on voltage : VF [ V ]Tj=125°CTj=25°C101001000100200300400500R e v e r s e r e c o v e r y c u r r e n t : I r r [ A ]R e v e r s e r e c o v e r y t i m e : t r r [ n s e c ]Forward current : IF [ A ]Irr (125°C)Irr (25°C)trr (125°C)trr (25°C)0.0010.0100.1001.0000.0010.0100.1001.000T h e r m a l r e s i s t a n s e : R t h (j -c ) [ °C /W ]Pulse width : Pw [ sec ]0.1110100-60-40-20020406080100120140160180Temperature [°C ]R e s i s t a n c e : R [ k Ω ]Outline Drawings, mmM6296MBI225U-120IGBT ModuleEquivalent Circuit Schematic[Thermister]135111210987246[Inverter]。
施耐德E型接触器
电动机起动与保护
产品目录
施耐德电气
善用其效 尽享其能
全球能效管理专家施耐德电气为世界100多个国家提供整体解决方案，其中在能源与基 础设施、工业过程控制、楼宇自动化和数据中心与网络等市场处于世界领先地位，在 住宅应用领域也拥有强大的市场能力。致力于为客户提供安全、可靠、高效的能源， 施耐德电气2010年的销售额为196亿欧元，拥有超过110,000名员工。施耐德电气助 您——善用其效，尽享其能！
17...80 A p
LC1E65
80A 110A
3 22 kW 37 kW 45 kW 55 kW 45 kW 45 kW
17...104 A p
LC1E80
95A 110A
3 25 kW 45 kW 45 kW 55 kW 45 kW 45 kW
17...104 A p
LC1E95
3
特性
TeSys® E 接触器
1
选型指南
应用
TeSys® E 接触器
LC1E06到E95
各种类型的控制系统
额定工作电流
额定工作电压 极数 额定工作功率 AC-3 类
辅助触点 适用手动-过载继电 浪涌抑制模块 接触器型号 页码
Ie max AC-3 (Ue≤440 V) Ie AC-1 (q≤60˚C)
220/230 V 380 V 415/440 V 500 V 660/690 V 1000 V
LC1E06到E95
接触器型号
工作环境
额定绝缘电压 (Ui) 额定冲击耐受电压 (Uimp) 符合标准 产品证书 绝缘隔离 防护等级 (1) (仅适用于正面) 保护措施 环境温度 设备周围
最大工作海拔 工作位置
阿特克（Altech Corp.）UL 系列微型箔式过流保护器说明文件说明书
U L 489A N N E XU L 508U L 1077U L 1077E q u i p m e n t B r e a k e r sE a r t h L e a k a g e C i r c u i t B r e a k e r s• 35 Royal Road • Flemington, NJ 08822-6000 • P 908.806-9400 • F 908.806.9490 • 10UL(AC),DL(DC) SeriesUL489 Miniature Molded Case Circuit BreakersCurrent/ Voltage RatingUL-Series DL-SeriesCalibration TemperatureAmbient Temperature Storage Temperature Terminal Size Acceptability Terminal Torque (min/max)Electrical Life Mechanical Life Vibration ResistanceResistance to mechanical shocks Degree of protection acc. IEC/EN 60529Mounting Orientation0.3 - 63A/ 240V AC, 0.3-32A/ 480Y/277V AC* (48V DC / pole pending)0.3 - 63A/ 125/ 250V DC 40ºC (104ºF)-25ºC to +55ºC (-13ºF to 131ºF )-40ºC to +70ºC (-40ºF to 158ºF )T op: 18-3 AWG; Bottom: 18-2 AWG 2 Nm (17.7 lb.in.) / 2.5Nm (22.2 lb.in)6,000 switching cycles ON/ OFF 10,000 switching cycles ON/ OFF> 15g according to DIN EN 60069-2-59 during a load with I 1= 1.05 x I N 25g @ 11ms IP20 In any planeIEC 60947-2Short Circuit Tested•Available in AC and DC models •DIN Rail Mounted •17.5mm width •Thermal Magnetic•Current Limiting (UL tested)•240V , 480Y/277V AC, 50/60Hz•125V DC (1 pole); 250V DC (2 pole)•10kA Short Circuit Interrupting Capacity •HACR T ype 40°C •Line/Load reversibleLISTED CUSE329510C.B.No.Poles Type 0.3-32A 40-63A 1AC 10kA @ 120, 240,10kA @ 120,277V 240V 2-3AC10kA @ 120, 240,10kA @ 120480Y/277V240VNo.Poles Type 0.3-3240-63A 1AC 15kA@240V 15kA@240V 2-3AC15kA@415V10kA@415VNo.Poles Type 0.3-32A 40-63A 1DC 10kA @ 125V 10kA @ 125V 2DC10kA @ 250V10kA @ 250V*One device, dual voltage ratings.Short Circuit Interrupting Capacity According to UL 489Short Circuit Interrupting CapacityAccording to IEC 60947-2, DIN EN 60947-2U L 489A N N E XU L 508U L 1077U L 1077E q u i p m e n t B r e a k e r sE a r t h L e a k a g e C i r c u i t B r e a k e r s • 35 Royal Road • Flemington, NJ 08822-6000 • P 908.806-9400 •F 908.806.9490 • 11D-Characteristics AC1.05xRC1.35xRC10xRC16xRCD-Characteristics DC1.05xRC1.35xRC14xRC22.4xRC*The value of each characteristic is shown vertically beneath its corresponding heading.Characteristic Trip Boundaries Trip-Characteristics*ApplicationsC-Characteristics ACC-Characteristics DCThermal TripLighting Control CircuitsWiring Protection Business Equipment AppliancesTransformersPower Supplies HeatersMust not Trip>100ms Must Trip <1hr Must not Trip>100ms Must Trip at 100ms Magnetic TripLowInrush High InrushMotorsReactive LoadTelecommu-nications/Computer EquipmentPower Supplies1.05xRC1.35xRC5xRC10xRC1.05xRC1.35xRC7xRC14xRCWarning!This information should only be used as a selection guide. T he use of a Miniature Circuit Breaker in an application with a certain T rip-Characteristic always requires prototype testing! It is the responsibility of the circuit design engineer to select the appropriate Miniature Circuit Breaker for his specific application.1 Pole2 Pole3 Pole17.5 mm36.5 m m 36.8 m m35 mm52.5 mm68.4 mm 51.5 mm30.5 mm51.5 mm37.5 mm25.5 mm 14.5 mm45 m m105.3 m m52.5 m m34.5 m m 8467Dimensions in mmTrip CharacteristicVoltage Rating Rated Current No. of PolesApproval for heating,refrigerating and air conditioning devices.Approval Circuit Diagram Short Circuit RatingProduct SeriesIndividual Part Number is shown Marking DetailsU L 489A N N E XU L 508U L 1077U L 1077E q u i p m e n t B r e a k e r sE a r t h L e a k a g e C i r c u i t B r e a k e r s• 35 Royal Road • Flemington, NJ 08822-6000 • P 908.806-9400 • F 908.806.9490 • 12C -TripCharacteristicLISTED C USE329510C.B.Application Examples:Low inrush motors, resistive loads, wiring protection, receptacles,lighting, and control circuit applications. Relatively short thermal trip delay and medium magnetic trip point.Standard Pack: 12Weight:0.3-32A:1.74kg (3.83lb.)40-63A:1.98kg (4.37lb.)Standard Pack: 6Weight:0.3-32A:1.74kg (3.83lb.)40-63A:1.98kg (4.37lb.)Standard Pack: 4Weight:0.3-32A:1.74kg (3.83lb.)40-63A:1.98kg (4.37lb.)Rated Type/ Rated Current Cat. No. Voltage 0.3A 1C03UL 277V AC 0.5A 1C05UL 277V AC 1.0A 1C1UL 277V AC 1.6A 1C1.6UL 277V AC 2.0A 1C2UL 277V AC 3.0A 1C3UL 277V AC 4.0A 1C4UL 277V AC 5.0A 1C5UL 277V AC 6.0A 1C6UL 277V AC 8.0A 1C8UL 277V AC 10A 1C10UL 277V AC 12A 1C12UL 277V AC 13A 1C13UL 277V AC 15A 1C15UL 277V AC 16A 1C16UL 277V AC 20A 1C20UL 277V AC 25A 1C25UL 277V AC 30A 1C30UL 277V AC 32A 1C32UL 277V AC 40A 1C40UL 240V AC 50A 1C50UL 240V AC 60A 1C60UL 240V AC 63A 1C63UL 240V ACOne PoleThree PoleTwo PoleAdd-on Neutral PoleRated Type/ Rated Current Cat. No. Voltage 0.3A 2C03UL 480Y/277V AC 0.5A 2C05UL 480Y/277V AC 1.0A 2C1UL 480Y/277V AC 1.6A 2C1.6UL 480Y/277V AC 2.0A 2C2UL 480Y/277V AC 3.0A 2C3UL 480Y/277V AC 4.0A 2C4UL 480Y/277V AC 5.0A 2C5UL 480Y/277V AC 6.0A 2C6UL 480Y/277V AC 8.0A 2C8UL 480Y/277V AC 10A 2C10UL 480Y/277V AC 12A 2C12UL 480Y/277V AC 13A 2C13UL 480Y/277V AC 15A 2C15UL 480Y/277V AC 16A 2C16UL 480Y/277V AC 20A 2C20UL 480Y/277V AC 25A 2C25UL 480Y/277V AC 30A 2C30UL 480Y/277V AC 32A 2C32UL 480Y/277V AC 40A 2C40UL 240V AC 50A 2C50UL 240V AC 60A 2C60UL 240V AC 63A 2C63UL 240V ACRated Type/ Rated Current Cat. No. Voltage 0.3A 3C03UL 480Y/277V AC 0.5A 3C05UL 480Y/277V AC 1.0A 3C1UL 480Y/277V AC 1.6A 3C1.6UL 480Y/277V AC 2.0A 3C2UL 480Y/277V AC 3.0A 3C3UL 480Y/277V AC 4.0A 3C4UL 480Y/277V AC 5.0A 3C5UL 480Y/277V AC 6.0A 3C6UL 480Y/277V AC 8.0A 3C8UL 480Y/277V AC 10A 3C10UL 480Y/277V AC 12A 3C12UL 480Y/277V AC 13A 3C13UL 480Y/277V AC 15A 3C15UL 480Y/277V AC 16A 3C16UL 480Y/277V AC 20A 3C20UL 480Y/277V AC 25A 3C25UL 480Y/277V AC 30A 3C30UL 480Y/277V AC 32A 3C32UL 480Y/277V AC 40A 3C40UL 240V AC 50A 3C50UL 240V AC 60A 3C60UL 240V AC 63A 3C63UL 240V ACRated Type/ Rated Current Cat. No. Voltage 0.3-32A N32UL 480/277V AC 40-63A N63UL 240V ACStandard Pack: 6Weight:0.99kg (2.18 lb.)Standard Dual Connection Terminal•Box clamp terminals Top: 18-3 AWG;Bottom: 18-2 AWG (Line/Load reversible)•Ring tongue terminalsRing tongueBox clamp*May differ by manufacturer. T op terminal ring tongue max. thickness 1.6mm.18.3 mm (0.72 in.)M5 screw11.3 mm (0.44 in.)m a x . 8-12 m m (0.31-0.47 i n .)5.3 m m (0.21 i n .)UL - SeriesU L 489A N N E XU L 508U L 1077U L 1077E q u i p m e n t B r e a k e r sE a r t h L e a k a g e C i r c u i t B r e a k e r s • 35 Royal Road • Flemington, NJ 08822-6000 • P 908.806-9400 •F 908.806.9490 • 13Application Examples:High inrush motors, transformers, power supplies, heaters and reactive loads. Relatively long thermal trip delay and very high magnetic trip point.LISTED C USE329510C.B.Standard Pack: 12Weight:0.3-32A:1.74kg (3.83lb.)40-63A:1.98kg (4.37lb.)Standard Pack: 6Weight:0.3-32A:1.74kg (3.83lb.)40-63A:1.98kg (4.37lb.)Standard Pack: 4Weight:0.3-32A:1.74kg (3.83lb.)40-63A:1.98kg (4.37lb.)Rated Type/ Rated Current Cat. No. Voltage 0.3A 1D03UL 277V AC 0.5A 1D05UL 277V AC 1.0A 1D1UL 277V AC 1.6A 1D1.6UL 277V AC 2.0A 1D2UL 277V AC 3.0A 1D3UL 277V AC 4.0A 1D4UL 277V AC 5.0A 1D5UL 277V AC 6.0A 1D6UL 277V AC 8.0A 1D8UL 277V AC 10A 1D10UL 277V AC 12A 1D12UL 277V AC 13A 1D13UL 277V AC 15A 1D15UL 277V AC 16A 1D16UL 277V AC 20A 1D20UL 277V AC 25A 1D25UL 277V AC 30A 1D30UL 277V AC 32A 1D32UL 277V AC 40A 1D40UL 240V AC 50A 1D50UL 240V AC 60A 1D60UL 240V AC 63A 1D63UL 240V ACOne PoleThree PoleTwo PoleAdd-on Neutral PoleRated Type/ Rated Current Cat. No. Voltage 0.3A 2D 03UL 480Y/277V AC 0.5A 2D 05UL 480Y/277V AC 1.0A 2D 1UL 480Y/277V AC 1.6A 2D 1.6UL 480Y/277V AC 2.0A 2D 2UL 480Y/277V AC 3.0A 2D 3UL 480Y/277V AC 4.0A 2D 4UL 480Y/277V AC 5.0A 2D 5UL 480Y/277V AC 6.0A 2D 6UL 480Y/277V AC 8.0A 2D 8UL 480Y/277V AC 10A 2D 10UL 480Y/277V AC 12A 2D 12UL 480Y/277V AC 13A 2D 13UL 480Y/277V AC 15A 2D 15UL 480Y/277V AC 16A 2D 16UL 480Y/277V AC 20A 2D 20UL 480Y/277V AC 25A 2D 25UL 480Y/277V AC 30A 2D 30UL 480Y/277V AC 32A 2D 32UL 480Y/277V AC 40A 2D 40UL 240V AC 50A 2D 50UL 240V AC 60A 2D 60UL 240V AC 63A 2D 63UL 240V ACRated Type/ Rated Current Cat. No. Voltage 0.3A 3D 03UL 480Y/277V AC 0.5A 3D 05UL 480Y/277V AC 1.0A 3D 1UL 480Y/277V AC 1.6A 3D 1.6UL 480Y/277V AC 2.0A 3D 2UL 480Y/277V AC 3.0A 3D 3UL 480Y/277V AC 4.0A 3D 4UL 480Y/277V AC 5.0A 3D 5UL 480Y/277V AC 6.0A 3D 6UL 480Y/277V AC 8.0A 3D 8UL 480Y/277V AC 10A 3D 10UL 480Y/277V AC 12A 3D 12UL 480Y/277V AC 13A 3D 13UL 480Y/277V AC 15A 3D 15UL 480Y/277V AC 16A 3D 16UL 480Y/277V AC 20A 3D 20UL 480Y/277V AC 25A 3D 25UL 480Y/277V AC 30A 3D 30UL 480Y/277V AC 32A 3D 32UL 480Y/277V AC 40A 3D 40UL 240V AC 50A 3D 50UL 240V AC 60A 3D 60UL 240V AC 63A 3D 63UL 240V ACRated Type/ Rated Current Cat. No. Voltage 0.3-32A N32UL 480/277V AC 40-63A N63UL 240V ACStandard Pack: 6Weight:0.99kg (2.18 lb.)Standard Dual Connection Terminal•Box clamp terminals T op: 18-3 AWG;Bottom: 18-2 AWG (Line/Load reversible)•Ring tongue terminalsRing tongueBox clamp*May differ by manufacturer. T op terminal ring tongue max. thickness 1.6mm.18.3 mm (0.72 in.)M5 screw11.3 mm (0.44 in.)m a x . 8-12 m m (0.31-0.47 i n .)5.3 m m (0.21 i n .)D -TripCharacteristicUL - SeriesU L 489A N N E XU L 508U L 1077U L 1077E q u i p m e n t B r e a k e r sE a r t h L e a k a g e C i r c u i t B r e a k e r s• 35 Royal Road • Flemington, NJ 08822-6000 • P 908.806-9400 • F 908.806.9490 • 14C -Trip (DC)CharacteristicApplication Examples:Telecommunication equipment,computer equipment, uninterruptable power supplies.Standard Pack: 12Weight:0.3-32A:1.86kg (4.1lb.)40-63A:2.10kg (4.6lb.)Standard Pack: 6Weight:0.3-32A:1.86kg (4.1lb.)40-63A:2.10kg (4.6lb.)Rated Type/ Rated Current Cat. No. Voltage 0.3A 1C03DL 125V DC 0.5A 1C05DL 125V DC 1.0A 1C1DL 125V DC 1.6A 1C1.6DL 125V DC 2.0A 1C2DL 125V DC 3.0A 1C3DL 125V DC 4.0A 1C4DL 125V DC 5.0A 1C5DL 125V DC 6.0A 1C6DL 125V DC 8.0A 1C8DL 125V DC 10A 1C10DL 125V DC 12A 1C12DL 125V DC 13A 1C13DL 125V DC 15A 1C15DL 125V DC 16A 1C16DL 125V DC 20A 1C20DL 125V DC 25A 1C25DL 125V DC 30A 1C30DL 125V DC 32A 1C32DL 125V DC 40A 1C40DL 125V DC 50A 1C50DL 125V DC 60A 1C60DL 125V DC 63A 1C63DL 125V DCOne PoleTwo PoleRated Type/ Rated Current Cat. No. Voltage 0.3A 2C03DL 250V DC 0.5A 2C05DL 250V DC 1.0A 2C1DL 250V DC 1.6A 2C1.6DL 250V DC 2.0A 2C2DL 250V DC 3.0A 2C3DL 250V DC 4.0A 2C4DL 250V DC 5.0A 2C5DL 250V DC 6.0A 2C6DL 250V DC 8.0A 2C8DL 250V DC 10A 2C10DL 250V DC 12A 2C12DL 250V DC 13A 2C13DL 250V DC 15A 2C15DL 250V DC 16A 2C16DL 250V DC 20A 2C20DL 250V DC 25A 2C25DL 250V DC 30A 2C30DL 250V DC 32A 2C32DL 250V DC 40A 2C40DL 250V DC 50A 2C50DL 250V DC 60A 2C60DL 250V DC 63A 2C63DL 250V DCStandard Dual Connection Terminal•Box clamp terminals Top: 18-3 AWG;Bottom: 18-2 AWG (Line/Load reversible)•Ring tongue terminalsRing tongueBox clamp*May differ by manufacturer. T op terminal ring tongue max. thickness 1.6mm.18.3 mm (0.72 in.)M5 screw11.3 mm (0.44 in.)m a x . 8-12 m m (0.31-0.47 i n .)5.3 m m (0.21 i n .)LISTED C USE329510C.B.UL - Series ++–––+Warning!Correct polarity must be observedwhen connecting the DC circuit breakers.U L 489A N N E XU L 508U L 1077U L 1077E q u i p m e n t B r e a k e r sE a r t h L e a k a g e C i r c u i t B r e a k e r s • 35 Royal Road • Flemington, NJ 08822-6000 • P 908.806-9400 •F 908.806.9490 • 15D -Trip (DC)CharacteristicApplication Examples:Telecommunication equipment,computer equipment, uninterruptable power supplies.Standard Pack: 12Weight:0.3-32A:1.86kg (4.1lb.)40-63A:2.10kg (4.6lb.)Standard Pack: 6Weight:0.3-32A:1.86kg (4.1lb.)40-63A:2.10kg (4.6lb.)Rated Type/ Rated Current Cat. No. Voltage 0.3A 1D03DL 125V DC 0.5A 1D05DL 125V DC 1.0A 1D1DL 125V DC 1.6A 1D1.6DL 125V DC 2.0A 1D2DL 125V DC 3.0A 1D3DL 125V DC 4.0A 1D4DL 125V DC 5.0A 1D5DL 125V DC 6.0A 1D6DL 125V DC 8.0A 1D8DL 125V DC 10A 1D10DL 125V DC 12A 1D12DL 125V DC 13A 1D13DL 125V DC 15A 1D15DL 125V DC 16A 1D16DL 125V DC 20A 1D20DL 125V DC 25A 1D25DL 125V DC 30A 1D30DL 125V DC 32A 1D32DL 125V DC 40A 1D40DL 125V DC 50A 1D50DL 125V DC 60A 1D60DL 125V DC 63A 1D63DL 125V DCOne PoleTwo PoleRated Type/ Rated Current Cat. No. Voltage 0.3A 2D03DL 250V DC 0.5A 2D05DL 250V DC 1.0A 2D1DL 250V DC 1.6A 2D1.6DL 250V DC 2.0A 2D2DL 250V DC 3.0A 2D3DL 250V DC 4.0A 2D4DL 250V DC 5.0A 2D5DL 250V DC 6.0A 2D6DL 250V DC 8.0A 2D8DL 250V DC 10A 2D10DL 250V DC 12A 2D12DL 250V DC 13A 2D13DL 250V DC 15A 2D15DL 250V DC 16A 2D16DL 250V DC 20A 2D20DL 250V DC 25A 2D25DL 250V DC 30A 2D30DL 250V DC 32A 2D32DL 250V DC 40A 2D40DL 250V DC 50A 2D50DL 250V DC 60A 2D60DL 250V DC 63A 2D63DL 250V DCLISTED C USE329510C.B.UL - Series Standard Dual Connection Terminal•Box clamp terminals Top: 18-3 AWG;Bottom: 18-2 AWG (Line/Load reversible)•Ring tongue terminalsRing tongueBox clamp*May differ by manufacturer. T op terminal ring tongue max. thickness 1.6mm.18.3 mm (0.72 in.)M5 screw11.3 mm (0.44 in.)m a x . 8-12 m m (0.31-0.47 i n .)5.3 m m (0.21 i n .)++–––+Warning!Correct polarity must be observedwhen connecting the DC circuit breakers.U L 489A N N E XU L 508U L 1077U L 1077E q u i p m e n t B r e a k e r sE a r t h L e a k a g e C i r c u i t B r e a k e r s• 35 Royal Road • Flemington, NJ 08822-6000 • P 908.806-9400 • F 908.806.9490 • 16Type/ Cat No.Description Contacts Type Std Pk H10UL 1 Auxiliary Contact 1NO 6H11UL 2 Auxiliary Contacts 1NO + 1NC 6H12UL 3 Auxiliary Contacts 1NO + 2NC 6H21UL 3 Auxiliary Contacts 2NO + 1NC 6HLS11L*1 Auxiliary/1 Signal Contact 1CO + 1CO (Signal)6Max. Operating Type/ Cat No.Rated Voltage U N Current @ U N Std Pk FA12UL 12V AC/DC 1.3A 5FA24UL 24V AC/DC 0.6A 5FA48UL 48 - 72V AC/DC 0.2A50.25A @ 110V FA110UL0.5A @ 240V 50.58A @ 277V110 - 240V AC/DC,277V ACRated Operating 10A@240V AC Currents3A@110V DC 1A@220V DC Minimum Contact Load 1mA @ 24V DC Torquemax. 0.8Nm (7 lb.in)Wire Range :Single Wire 1.0mm² - 2.5mm² (18-14 AWG)Stranded Wire 1.0mm² - 1.5mm² (18-16 AWG)Stranded Wire 1.0mm² - 1.5mm² (18-16 AWG)with FerruleType/ Cat No.Rated Current I NRated Voltage U N Std Pk N32UL 0.3 - 32A 480Y/277V AC 6N63UL40 - 63A240V AC6UL/DL Series AccessoriesAuxiliary Contact, Alarm SwitchShunt TripNeutral Pole8.8 mm63.8 mm6 mm45 m m87 m m 52.7 m m17.7 m m51.5mm 37.5mm 25.5mm52.5m m45m m34.5m m36.5m m36.8m m105.3m m6mm7mm8mm 14.5mm17.5mm30.5mm 51.5mm 68.4mm4mm89.5 m m45 m mc a . 180-20045 m m17.5 mm21.8 mmAWG 236 mm68.4 mm43.6 mm45 m m88 m m9 mm68.4 mm43.8 mm63.8 mm6 mm12.4 mmLISTED C.B. ACC.3NY7CUSE335632For mounting instructions please refer to page 43.Dimensions HxxUL.Dimensions HLS11L.Dimensions NxxUL, FAxxULDimensions UA120ULType/ Cat No.Line Voltage V E Std Pk UA120UL120V AC, 60Hz5Reset-Hold Voltage = 0.85 x V EDrop-Out Voltage = 0.35 ~ 0.7 x V EV E = Rated Voltage* UL not approved.Undervoltage Trip*Type/ Cat No.Std Pk E98341910Mounting Screw 34mmto connect the auxiliary contact and shunt trip or neutral Pole to the circuit breaker.Type/ Cat No.Std Pk EASS10Type/ Cat No.Std Pk 15.9601Lock-out Adapter**Type/ Cat No.Std Pk BS.UL100Touch Protection Capsto cover the terminal screw holes on the switching devices, neutral Poles and shunt trips for increased touch protection.Cooling Spacer**UL and DL series can also be locked in the on and off position by simply using a common lead or meter seal, which gets fed through the hole in the handle and a corresponding hole in the housing.1/4”U L 489A N N E XU L 508U L 1077U L 1077E q u i p m e n t B r e a k e r sE a r t h L e a k a g e C i r c u i t B r e a k e r s• 35 Royal Road • Flemington, NJ 08822-6000 • P 908.806-9400 • F 908.806.9490 • 17“C” Magnetic Trip Parameters Rated current 0.3A to 63A.1. Hold for a minimum of 100ms at surge of 5 times rated current.2. Trip in under 100ms at 10 times rated current.“D” Magnetic Trip Parameters Rated current 0.3A to 63A.1. Hold for a minimum of 100ms at surge of 10 times rated current.2. T rip in under 100ms at 16 times rated current.10-34x10-310-24x10-210-10.41410141040601234568102040100Multiple of Rated CurrentS e c o n d sM i n u t e sT r i p p i n g t i m e tThermal Overload“Must T rip” < 1 hr = 135% RC “Must Not Trip” > 1 hr = 105% RC1.05-1.35xI N 0.3A Through 10A Rated Current 10-34x10-310-24x10-210-10.41410141040601234568102040100Multiple of Rated CurrentS e c o n d sM i n u t e sT r i p p i n g t i m e tThermal Overload“Must T rip” < 1 hr = 135% RC “Must Not Trip” > 1 hr = 105% RC1.05-1.35xI N 12A Through 63A Rated Current1.05-1.35xI N1234568102040100Multiple of Rated Current10-34x10-310-24x10-210-10.4141014104060S e c o n d sM i n u t e sT r i p p i n g t i m e t16Thermal Overload“Must T rip” < 1 hr = 135% RC “Must Not T rip” > 1 hr = 105% RC0.3A Through 10A Rated Current10-34x10-310-24x10-210-10.4141014104060123451668102040100Multiple of Rated CurrentS e c o n d sM i n u t e sT r i p p i n g t i m e tThermal Overload“Must T rip” < 1 hr = 135% RC “Must Not T rip” > 1 hr = 105% RC1.05-1.35xI N 12A Through 63A Rated CurrentUL Series (AC) Trip CurvesC (AC) Trip CurveD (AC) Trip CurveU L 489A N N E XU L 508U L 1077U L 1077E q u i p m e n t B r e a k e r sE a r t h L e a k a g e C i r c u i t B r e a k e r s• 35 Royal Road • Flemington, NJ 08822-6000 • P 908.806-9400 • F 908.806.9490 • 1810-34x10-310-24x10-210-10.41410141040601234567810142040100Multiple of Rated CurrentS e c o n d sM i n u t e sT r i p p i n g t i m e tThermal Overload“Must Trip” < 1 hr = 135% RC “Must Not T rip” > 1 hr = 105% RC1.05-1.35xI N 0.3A Through 10A Rated Current 1.05-1.35xI N1234578102040100Multiple of Rated Current 10-34x10-310-24x10-210-10.4141014104060S e c o n d sM i n u t e sT r i p p i n g t i m e t14Thermal Overload“Must Trip” < 1 hr = 135% RC “Must Not T rip” > 1 hr = 105% RC12A Through 63A Rated Current 10-34x10-310-24x10-210-10.41410141040601234568101422.440100Multiple of Rated CurrentS e c o n d sM i n u t e sT r i p p i n g t i m e tThermal Overload“Must T rip” < 1 hr = 135% RC “Must Not Trip” > 1 hr = 105% RC1.05-1.35xI N 0.3A Through 10A Rated Current10-34x10-310-24x10-210-10.41410141040601234514681022.440100Multiple of Rated CurrentS e c o n d sM i n u t e sT r i p p i n g t i m e tThermal Overload“Must T rip” < 1 hr = 135% RC “Must Not T rip” > 1 hr = 105% RC1.05-1.35xI N 12A Through 63A Rated CurrentUL Series (DC) Trip CurvesC (DC) Trip CurveD (DC) Trip Curve“C” Magnetic Trip Parameters Rated current 0.3A to 63A.1. Hold for a minimum of 100ms at surge of 7 times rated current.2. Trip in under 100ms at 14 times rated current.“D” Magnetic Trip Parameters Rated current 0.3A to 63A.1. Hold for a minimum of 100ms at surge of 14 times rated current.2. Trip in under 100ms at 22.4 times rated current.U L 489A N N E XU L 508U L 1077U L 1077E q u i p m e n t B r e a k e r sE a r t h L e a k a g e C i r c u i t B r e a k e r s • 35 Royal Road • Flemington, NJ 08822-6000 • P 908.806-9400 •F 908.806.9490 • 19Short Circuit Current I [kA]Time Basis:t=8.3msUL/ DL Series Internal ResistanceUL Series Let-through Energy I 2t Diagram, D Trip 1 poleRated CurrentTrip Characteristic (A)C D (Ohm)(Ohm)0.316.862016.86200.5 6.8540 6.00091.0 1.7000 1.75601.60.58700.58702.00.41900.41903.00.20200.20204.00.10900.10905.00.06540.06546.00.05280.04918.00.02780.0240100.02160.0187120.00840.0085130.00840.008515/ 160.00850.0076200.00670.0064250.00500.004130/ 320.00320.0027400.00250.0022500.00190.001860/ 630.00180.0017For other Trip/Pole configurations use the following correction factors:C T rip 1 pole + 0.84 x curve value C T rip 2 pole + 0.71 x curve value C T rip 3 pole + 0.92 x curve valueD T rip 1 pole + 1.00 x curve value D T rip 2 pole + 0.87 x curve value D T rip 3 pole + 1.08 x curve value。
6RA70参数表
[自版本 1.8 起]
o4 等待电压(电枢)
o4.0 等待在电源端子 1U1，1V1，1W1 的电压。电压和频率必须在参数
P351，P352，P353，P363 和 P364 规定的范围内。也见 P078.001。
o4.1 等待熔断器监控器 OK 信号
[自版本 1.7 起]
10) 参数在第 8 章指定的功能图加以表示(此处为图 G153)。
11-4
Siemens Electrical Drives Ltd. 6RX1700-0AD50 SIMOREG DC Master 使用说明书
05.2007
参数号 说 明
值范围 [单位] 步长
11.1
r000
运行状态显示
运行状态显示 状态显示，故障和报警信息
模拟工作模式激活(见 U840)
功能 运行显示 一般只读参数 访问权等级 SIMOREG DC MASTER 整流器定义 SIMOREG DC MASTER 功率部分定义 整流器控制设定值 电动机的定义 脉冲编码器定义，使用脉冲编码器作为速度检测 电枢电流闭环控制，自动换向部分，电枢触发单元 电流限幅，转矩限幅 自动换向部分，电枢触发单元 速度调节器(速度调节器其他参数 P550~P567) 励磁电流闭环控制，励磁触发单元 EMF 闭环控制 斜坡函数发生器 给定值处理 斜坡函数发生器 监控功能和限幅的设定值 限幅值监控的设定值 可设置的固定值 固定控制位 数字给定输入(固定给定值，点动和爬行给定) 用脉冲编码器的位置检测 连接器选择开关 电动电位计 振荡 “电动机接口”的定义 转矩层输入的配置 速度限幅调节器 摩擦补偿 转动惯量补偿(接入 dv/dt) 速度调节器(速度调节器详细参数见 P200 - P236) 励磁反向 信号的输入量 闭环控制的配置 控制字，状态字 进一步的配置方法 模拟量输入(主实际值，主给定值，可选输入)
《UM125T产品》课件
市场前景分析
市场需求：随着城市化进程的加快，人们对出行的需求日益增长
竞争分析：UM125T产品面临来自其他品牌的竞争，需要不断提高产品质量和性能
发展趋势：随着环保意识的提高，电动车市场将逐渐扩大，UM125T产品需要适应这一趋 势
技术发展：随着科技的进步，电动车的技术将不断提高，UM125T产品需要不断更新 技术，提高竞争力
用户反馈和评价
用户评价：UM125T产品性能稳定， 操作简便，易于维护
用户评价：UM125T产品性价比高， 价格合理
添加标题
添加标题
添加标题
添加标题
用户反馈：UM125T产品外观设计 时尚，符合现代审美
用户反馈：UM125T产品售后服务 周到，响应迅速
Part Six
UM125T产品的市 场前景和发展趋势
UM125T产品介绍
PPT,a click to unlimited possibilities
汇报人：PPT
目录
01 添 加 目 录 项 标 题 03 U M 1 2 5 T 产 品 规 格 和 参 数
02 U M 1 2 5 T 产 品 概 述 04 U M 1 2 5 T 产 品 功 能 和 优 势
05 U M 1 2 5 T 产 品 的 用 户 体 验
07 U M 1 2 5 T 产 品 的 品 质 保 障 和 服务支持
06 U M 1 2 5 T 产 品 的 市 场 前 景和发展趋势
Part One
单击添加章节标题
Part Two
UM125T产品概述
产品名称和型号
产品名称：UM125T 型号：UM125T 生产厂家：未知
解决方案和应用案例
解决方案：UM125T产品提供了一套完整的解决方案，包括硬件、软件和服务。 优势：UM125T产品具有高性能、高可靠性、高安全性等特点，能够满足不同客户的需求。
电池片等级划分标准
备注：以下情况必须通过特采流程：（1）厚度不符合上述情况时；（2）电性能不符合上述情况时；
硅太阳电池检验标准
1、 太阳电池的外观检验
a) 单晶硅电池，与表面成35°角日常光照情况下观察表面颜色，呈“褐；紫；兰”三色，目视颜色均匀，无明显色差、水痕
b) 多晶硅电池，与表面成35°角日常光照情况下观察表面颜色，呈“褐；紫；兰”三色，目视颜色均匀，无明显色差、水痕、手印。
c) 电极图形清晰、完整、无断线。
背面铝背电极完整，无明显凸起的“铝珠。
d) 电池受光面不规则缺损处面积小于1mm2，数量不超过2个。
e) 电池边缘缺角面积不超过1mm2，数量不超过2个。
f) 电池片上不允许出现肉眼可见的裂纹。
g) 正放电池片于工作台上，以塞尺测量电池的弯曲度，“125片”的弯曲度不超过0.75mm，
4、检验规则
a) 太阳电池电性能进行在线100%检验，根据转换效率和工作电流分档。
b) 太阳电池外观检验进行在线100%检验
c) 其它项目的抽样方案按GB2828中规定采用正常一次抽样方案。
检查水平为S-1、合格质量水平（AQL=2.5）
5、太阳电池的运输、贮存
在有外包
、水痕、手印。
、水痕、手印。
NUC微控制器产品系列说明书
M251 Feature
。 Arm® Cortex®-M23 。 运行速度可达 48 MHz
M252 Feature
。 USB 2.0 全速设备无需外 挂晶振
M253 Feature
。 USB 2.0 全速设备无需外 挂晶振
。 高达五路 UART 。 CAN FD x1
2
Low Power
TrustZone
AEC-Q100
Market Trend
随着电子应用对低功耗或电池供电的需 求日益增加，现今的应用必须尽量降低 能源消耗，甚至在极端情况下，可能需 要倚赖单颗电池来维持长达 15 至 20 年 运转
低功耗应用情景包含手持式设备、居家、 AIoT、IIoT (工业物联网) 等应用情景， 使用范围十分广泛
(Programmable Serial I/O) • USB 2.0 全速装置无需外挂晶振 • 独立的 RTC 电源 VBAT 管脚
Highlight
• 支持 1.8 V ~ 5.5 V 串行接口，可连接不同电压 装置
*USCI: Universal Serial Control Interface Controller
C
1.8 3.3 5 M253
CU
3.3 5 M071
1.8 3.3 5 M252
U
3.3 5 M051
1.8 3.3 5 M251
3.3 5 Mini51
3.3 5 3.3 5
1.8 3.3 Nano100
M480 M460 M471 M453 M452 M451
E CU E CU
U C
U
Arm9™
ITR9606中文资料
160
140
2
120
100 80
60
40
20
0 0 10 20 30 40 50 60 70
Fig.5 Collector Dark Current vs.
Ambient Temperature
10
10 10
10
10
0
25
50 75 100
Fig.4 Collector Current vs. Irradiance
1.3
1.2 IF=20mA
1.1
Ie-Radiant Intensity (mW/sr)
0 25 50 75 100 120
1 25 50 75 100 120
Everlight Electronics Co., Ltd. Device No：CDRX-096-004
http:\\ Prepared date：08-08-2005
http:\\ Prepared date：08-08-2005
Rev 3
Page: 3 of 6
Prepared by：Denky
元器件交易网
█ Typical Electrical/Optical/Characteristics Curves for IR
--- --- 10 μA
VR=5V
--- 940 --- nm
IF=20mA
--- 60 --- Deg
IF=20mA
--- --- 100 nA VCE=20V,Ee=0mW/cm2
VCE(sat) --- --- 0.4 V
IC=2mA ,Ee=1mW/cm2
Collect Current Transfer
ncp1252a中文规格书
ncp1252a中文规格书一、概述ncp1252a是一款高性能的数字信号处理器，主要用于工业控制、数据采集等领域。
本规格书详细介绍了ncp1252a的硬件架构、软件接口、性能参数、电气特性、温度特性等方面，以便用户更好地了解和使用该芯片。
二、产品特点1. 高性能：ncp1252a具有高速的数据处理能力，适用于高速数据采集和实时控制应用。
2. 兼容性好：ncp1252a支持多种编程语言，易于集成到现有的系统中。
3. 集成度高：ncp1252a内部集成了多种功能模块，降低了系统设计的复杂性。
4. 功耗低：ncp1252a采用低功耗设计，适用于需要长时间运行的应用场景。
三、硬件架构ncp1252a芯片采用x86架构，内部集成了处理器核心、内存控制器、高速I/O接口等。
芯片的主要接口包括：1. 数据输入输出接口：支持高速数据输入输出，最高数据传输速率可达500Mbps。
2. 模拟信号输入接口：支持多路模拟信号输入，适用于模拟信号采集和控制应用。
3. 数字信号输出接口：支持多路数字信号输出，可用于控制其他芯片或设备。
4. 串行接口：支持RS-232和USB等串行接口，便于与外部设备进行通信。
四、软件接口ncp1252a提供了一组标准的API函数，用户可以通过编程调用这些函数来实现对芯片的控制和操作。
主要API函数包括：1. 初始化函数：用于配置芯片的各项参数，包括工作模式、时钟频率等。
2. 数据读取函数：用于从芯片的数据输入输出接口读取数据。
3. 数据写入函数：用于向芯片的数据输入输出接口写入数据。
4. 模拟信号采集函数：用于采集模拟信号输入接口的数据。
5. 数字信号控制函数：用于控制数字信号输出接口的输出状态。
五、性能参数ncp1252a的性能参数如下：1. 处理器核心：主频最高可达xxxMHz，数据处理速度xxxMIPS。
2. 数据输入输出接口：最高数据传输速率xxxMbps，支持xxx位数据总线。
3. 模拟信号输入接口：支持xxx路模拟信号输入，采样率xxxS/s，精度xxx 位。
6r125p场效应管参数
场效应管参数
场效应管（Field-Effect Transistor，简写为 FET）是一种常见的电子元器件，广泛应用于放大、振荡、开关等电路中。
在选择和使用场效应管时，我们需要关注其参数，如：
1. 漏极源极电压（Vds）：指场效应管正常工作时，漏极与源极之间的电压。
这个参
数需要根据电路的需求进行选择，过高的电压可能会导致场效应管损坏。
2. 栅极源极电压（Vgs）：指场效应管正常工作时，栅极与源极之间的电压。
这个参
数对于场效应管的性能影响较大，需要谨慎选择。
3. 漏极电流（Id）：指场效应管正常工作时，漏极的电流大小。
这个参数需要根据电
路的需求进行选择，过大或过小的电流都可能影响电路的性能。
还有其他一些参数，如栅极输入电阻、反馈电容、导通电阻等，也需要根据具体应用
进行选择。
在选择场效应管时，需要根据具体的应用场景和需求，综合考虑各种参数，选择最适合的场效应管。
A3P125中文资料
QN1325 VQ100
PQ208 FG144, FG2565
400 k 9,216
54 12 1k Yes 1 18 4 194
600 k 13,824
108 24 1k Yes 1 18 4 235
1M 24,576
144 32 1k Yes 1 18 4 300
ProASIC3 Devices
ARM-Enabled ProASIC3 Devices
A3P030 A3P060 A3P125
A3P250 3
A3P400 3
M7A3P250 3, 4 M7A3P400 3 I/O Type
A3P600 M7A3P600
A3P1000 M7A3P1000
Single-Ended I/O Single-Ended I/O Single-Ended I/O Single-Ended I/O2 Differential I/O Pairs Single-Ended I/O2 Differential I/O Pairs Single-Ended I/O2 Differential I/O Pairs Single-Ended I/O2 Differential I/O Pairs
PQ208
PQ208
PQ208
FG144, FG256, FG144, FG256, FG144, FG256,
FG484
FG484
FG484
Notes:
1. Refer to the CoreMP7 datasheet for more information. 2. AES is not available for ARM-enabled ProASIC3 devices. 3. Six chip (main) and three quadrant global networks are available for A3P060 and above. 4. For higher densities and support of additional features, refer to the ProASIC3E Flash FPGAs datasheet. 5. The M7A3P250 device does not support this package.
2011年Optoma产品介绍(新)
EH7500
EH7500
7000 ISO21118流明, 满足大礼堂、会议室高 亮度需求
WUXGA 1920x1200分辨率，可 点对点显示1080P蓝光 高清画面和1600x1200 宽屏画面
EH7500
双灯同步、交替工 作、单灯独立工作等多 种模式,也用于全天候 无间断监测环境
电动镜头位移功能， 投影画面可以横向、纵 向无损平移，全部操作 均可通过遥控器完成
IS802
降噪Noise Reduction, 动作适应性降噪功能可以 减少隔行扫描信号中可见 噪点的数量
赠
随机附赠英国品牌 DMilc 100”电动壁挂玻 纤灰幕
IS802
2200流明高亮度设计 高对比度 8000：1(最大值) 完美支持1080P/24HZ 显示HDTV 1080i/p无失真 蝶恋花，度身定制中国元素 Optoma独家第三代Truevivid 影响技术 超高ANSI真实对比 强悍的可微调进阶影响处理引擎 内建6组“用户自定义的进阶影像处理” 内建噪讯消除(NR) 搭配六段色轮 背光设计的遥控器 小巧轻盈的机身仅重2.88kg 随机附赠英国品牌DMilc100”电动壁挂玻纤灰幕
HD20 HD33 HD20LV
XE152
XE149
IS500
XE151
PK301
微型机
DV20a
WVGA
ML500
WXGA
即将上市
WVGA 即将上市
明星机型简介
EH7500 EX665UT ES521 / EX521 / EX539 IS802 PK301 / ML500 /DV20a
EH7500
扬声器 尺寸 重量
ML500
500LM Luminus超高亮三色LED光源 WXGA 1280x800分辨率 支持DLP-Link 3D, 相容于DLP-3D眼镜 LED光源20000小时超长使用寿命 封闭式光机设计，光路与散热分开动作，环境耐受度高 內建陀螺仪, 可自动侦测角度执行梯形校正与画面反向 内建多媒体, MicroSoft Office, 以及PDF 解码功能 內含2GB閃存, 内置SD卡插槽，可直读存储卡中文件 完美输入接口，HDMI v1.3、USB 接口、VGA等 USB 接口 ,可供PC直接USB投影, 以及多媒体文件读取
中国商品说明书：中文版中国商品说明书：中文版
E-Panel InstructionsModel: MNE125ST, MNE175ST, MNE250ST, MNE125AL, MNE175AL, MNE250AL,MNE175STS, MNE250STS, MNE125LT, MNE175LT, MNE250LT, MNE125ALT, MNE175ALT, MNE250ALT, MNE125AL PLUS, MNE175AL PLUS, MNE250 PLUSMNE125STM, MNE175STM, MNE250STM, MNE125ALM, MNE175ALM, MNE250ALM, MNE125STMM, MNE175SM, MNE250SMLeft and Right hand 120/240VAC versionsModel Number code:MNE---------------175-----------ST or AL----------------M-240IMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONS - These instructions contain important safety and operating instructions for MidNite Solar E-Panels.If you do not fully understand any of the concepts, terminology, or hazards outlined in these instructions, please refer installation to a qualified dealer, electrician or installer. These instructions are not meant to be a complete explanation of a renewable energy system.GENERAL PRECAUTIONSWORKING WITH OR IN THE VICINITY OF A LEAD ACID BATTERY, SEALED OR VENTED IS DANGEROUS. VENTED BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL OPERATION. FOR THIS REASON, IT IS VERY IMPORTANT THAT BEFORE SERVICING EQUIPMENT IN THE VICINITY OF LEAD-ACID BATTERIES YOU REVIEW AND FOLLOW THESE INSTRUCTIONS CAREFULLY.If service or repair should become necessary, contact MidNite Solar Inc. Improper servicing may result in a risk of shock, fire or explosion. To reduce these risks, disconnect all wiring before attempting any maintenance or cleaning. Turning off the inverter will not reduce these risks. Solar modules produce power when exposed to light. When it is not possible to disconnect the power coming from the Photovoltaics by an external means such as a combiner, cover the modules with an opaque material before servicing any connected equipment.Never attempt to charge a frozen battery.When it is necessary to remove a battery, make sure that the battery bank disconnect breaker is in the off position and that the PV breakers, grid breakers and any other sources of power to the inverter are in the off position. Then remove the negative terminal from the battery first.To reduce risk of battery explosion follow these instructions and those published by the battery manufacturer as well as the manufacturer of any additional equipment used in the vicinity of the batteries. Before installing the battery enclosure, read all instructions and cautionary markings in or on any connected electrical equipment.Avoid producing sparks in the vicinity of the batteries when using vented batteries. Provide ventilation to clear the area of explosive gases. Sealed AGM and Gel batteries do not under normal conditions create explosive gases. Be especially cautious when using metal tools. Dropping a metal tool onto batteries can short circuit them. The resulting spark can lead to personal injury or damage to the equipment. Provide ventilation to outdoors from the battery compartment when installing vented batteries such as golf cart T-105 batteries. The addition of a spill tray is also a good idea.Clean all battery terminals. Very high currents are drawn from the batteries; even a small amount of electrical resistance can result in overheating, poor performance, premature failure or even fire.Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing or eyes. Wear complete eye and clothing protection. Always avoid touching eyes while working near batteries. If battery acid or battery terminal corrosion contacts skin or clothing, wash immediately with soap and water. If acid enters the eyes, immediately flood with cool running water for at least 15 minutes and get medical attention immediately. Baking soda neutralizes battery acid electrolyte. Keep a supply near the batteries.Do not work alone. Someone should be in the range of your voice or close enough to come to your aid when you work with or near electrical equipment.Remove rings, bracelets, necklaces, watches etc. when working with batteries, photovoltaic modules or other electrical equipment. Power from an illuminated photovoltaic array makes a very effective arc welder with dire consequences if one of the welded pieces is on your person.To reduce the risk of injury, connect only deep cycle lead acid type rechargeable batteries. Other types of batteries may leak or burst, causing personal injury or damage.This equipment is NOT intended for use with life support equipment or other medical equipment or devices.It is the responsibility of the installer to verify compliance with all applicable codes.Before making any connections verify that the circuit breakers are in the off position including the inverter breaker. Double check allwiring before applying power.The MidNite Solar E-Panel comes standard with the basic over-current protection and disconnects required to install your renewable energy system. It can also expand to grow as your needs arise.List of features:● Steel or aluminum chassis with all the r equired openings and knock outs to aid in a NEC compliant system installation● Inverter mounts on a unique hinged door to keep the footprint of the system small as possible● Mounting brackets are included to aid in one person installations● Inverter ba ttery breaker, inverter cables and snap in grommets included*● 500 amp / 50mv shunt included for battery monitoring systems● B us bars are included for additional battery plus, PV plus and battery minus wiring● Heavy duty 175 amp AC power distribution bu s bars included● 50 amp AC input disconnect for generator or utility included, pre-wired (15amp MM series) ● 50 amp AC bypass switch for bypassing inverter circuit, pre-wired (15amp MM series)● Mounting bracket to aid in mounting an OutBack MX60 or MidNi te Classic to the side of the E-Panel*● Battery cable cover to enclose cables external to the chassis***● Inverter and charge controller mounting hardware● Rectangular cut outs for mounting a North American GFCI style AC outlet● Cut outs for mounting up to six additional 13mm wide din rail mount breakers and three ¾” wide panel mount breakers for additional circuits such as PV, wind, hydro or AC distribution ● Plastic snap in conduit and fittings from chassis to inverter for AC, BTS and control circu its (OB versions)● ETL listed to UL and CSA standards* inverter cables and charge control bracket omitted on the LT configurations*** LT versions do not have a cable cover, MM series uses the inverter battery terminal capsThe dimensioned chassis drawings above show the location of the conduit knockouts, mounting holes and mounting brackets.✓Knockouts on the top surface are directly in line with ones on the bottom surface for stacking units vertically.✓Knockouts on the lower end of each side are directly in line with each other for stacking horizontally.✓Steel powder coated units are gray textured. Aluminum powder coated units are gloss white.Door ConfigurationThe standard E-Panel comes as a left hand hinged assembly with breakers on the left side and a left hand hinged door. The door will open to the left over the breakers. If for some reason you need the breakers on the left, but the door to open to the right, then you need the optional right hand door. All breakers can be unmounted and reassembled on the right side of the chassis as is explained in this manual. Right hand E-Panels can be built special at the factory for no additional charge. Changing sides in the field is not a simple task! The left hand hinge is standard because the majority of charge controllers need to be mounted to the right side of the E-Panel. See below.1. Apollo T-80 should be a left hand hinge (heatsink is on the right)3. OutBack MF80 should be left hand hinge (No knock out on the right side of chassis)4. MX60 works equally as well on either side5. WX controller works equally as well on either side6 C40/C60 and Tri-star work equally as well on either side7. Blue Sky has the heatsink on the left, so should use a right hand hinge.See E-Panels explained on the MidNite website for exact part numbers of door options and an explanation of each E-Panel platform. E-Panels Explained will further help you in selecting the applicable E-Panel for your application.The installation begins by selecting a wall. All E-Panels are indoor rated and should not be placed outside unless precautions are made to keep rain and moisture off of the system. The wall must have suitable clearance to open the door with inverter attached. It must also have adequate clearance to operate the breakers and outlets that protrude out the sides. The NEC requires 30” clear on the wall. The E -Panel may be located anywhere within this 30 inches, however make sure you have sufficient room to the side to operate the circuit breakers. Some E-Panel installations may have circuit breakers on both sides. The NEC also requires 36 inches free and clear of obstructions in front of the E-Panel. The 36” clear area in front of all electrical panels is to provide a space to fall back into incase of electrical shock. Each E-Panel with its’ inverter will weigh close to 100 pounds so make sure your wall is adequate for this load. The mounting brackets provided will span studs on 16 inch centers. Mount the top bracket as shown at about 64-68 inches off the floor. If stacking two systems vertically, make sure the breakers fall within the NEC guidelines for height, (lowest and highest allowable). Number 10 screws with back up washers will suffice, but ¼” (6mm) hardwar e provides for a better margin of safety.A little pre-planning here will go a long way towards a successful installation. Battery boxplacement and size also need to be thought out for NEC compliance. The remote display should be approximately at eye level when attached to the E-Panel. Some installation photos below show various ways to install your system.You can make life a little easier by installing additional breakers for charge control, the inverter and such while the E-Panel is still lying horizontal on a table. Do as much of the additionalwiring as possible before hanging the E-Panel on the wall. The following pictures show some of the operations that can be done “on the bench” where access is optimal.Field installed breakers should be torqued to 20 inch pounds, then re-torqued after one hour. This is important! Wires cold flow and sometimes loosen up after the initial tightening, so don’t skip this step. E-Bay is a good source for Sturdevant Richmont torque screw drivers if you are an installer.Breakers such as charge control input and output and DC-GFP can be completely wired prior to installation on the wall. Field wiring is done at the PV, AC and DC terminal bus bars.This picture shows the Outback E-Panel mountedwith two MNEPV63 charge control breakersinstalled and an AC and DC MNSPD Surge ProtectorDevice. The upper mounting bracket can be securedto the wall and then the E-Panel chassis hung ontoit using the keyhole slots in the upper back of thechassis.Before mounting the inverter to the chassis andwith the E-Panel mounted on the wall, complete allwiring that will be coming to and going from the E-Panel. The following pictures give you some idea ofwhat to expect.The picture to the right is a Magnum 240V E-Panel.Notice it has an OutBack OBDC-GFP mounted on the leftside of this right hand hinge unit. There are a total of sixdin rail slots available on each E-Panel for customerconfiguration. This installation has two chargecontrollers. You need a breaker in the PV input and onthe DC output of the charge controller. This took up 4din rail slots for this system. The MidNite DC-GFP takesup 2 din rail slots for the 63 amp version and 2 panelmount knock out slots for the 80 amp version. Neitherone of these would work in this case, so the two circuitOutBack GFP was used. It takes up three slots on theblank plate opposite the din rails. Note the green 6AWGneutral to ground bonding wire in this picture. Theneutral to ground bond is required on all systems perNEC. Note that if this were a power back up system on autility connected home, this bonding wire would not beinstalled as it would already be there on the serviceentrance. On off-grid installations thatemploy a sub panel circuit breaker box, you can make this neutral to ground bond in the sub-panel. It is technically better to make this bond closest to the source of power (the E-Panel), but many electrical inspectors will be looking for it in the sub-panel box. It will work just fine in either location, just make sure you have adequate conductor sizes between the E-Panel and the sub-panel. Do not rely on the hinges for grounding the equipment mounted to the door.The picture to the left shows the charge control bracket suppliedin the E-Panel kit. This one is for a left hand hinged unit, so thecharge control bracket is on the right side opposite the din railbreakers.The charge control bracket supplied works with the OutBackMX60, MF80, MidNite Classic and Xantrex WX charge controllers.The Charge control bracket is secured to the E-Panel with 3 #10 x3/8” sheet metal e one more screw to secure the topbracket of charge controller and a 1” close nipple on the side asshown below. Note tha t it takes three 1” locknuts to mount the controller. One lock nut is used in between the E-Panel side and the charge controller side to act as a spacer. It may help to replace the pan head screws on the side plate with flat head screws in some cases to increase clearance.In addition to the 1” close nipple andthree locknuts, you will need plasticthreaded adapters installed on the endsof the metal threaded nipple. Theseadapters protect wires from coming intocontact with the sharp edges of themetal close nipple.Before wiring the charge controller,determine what size wire and breakerswill be required. The breakers are there to protect the wiring, notthe controller!It is very common to use the MidNite 63 amp din rail breakers for this task. Even if the charge controller is only 30 amps, it can be wired using 63 amp breakers. You will need 6AWG wire to go with those breakers though. If using one of the more powerful 80 amp charge controllers, you will need the MNEDC80 panel mount breakers. These mount on the opposite wall from the din rail breakers. 4AWG wire is required to match up with these 80 amp breakers.The flow path for the PV circuit is as follows:1.The PV + wire comes into the E-Panel and attaches to the PV+ busbar2.The PV- comes into the E-Panel and attaches to the shunt busbar. This is for charge controllers thathave a common PV- and battery- connection, (most are this way). Some charge controllers like the Xantrex XW and the Blue Sky must keep thes PV- and battery- circuits separated. The E-Panels have mounting embosses to accommodate a short white busbar to act as an isolated PV-. Use theMNSBBW for the busbar.3.From the PV+ busbar, use the appropriate gauge red wire (THHN) and connect to the PV+ INbreaker. DC breakers have polarity markings. These may be a + sign or a line and load sign.Although the PV circuit has very limited energy available and thus making polarity issues not too critical, it is best to try to get it right. This is where the fun begins.4. The + (line) marking on the breaker would seem to indicate that you should connect the PV+ tothis terminal since the PV+ is the highest potential in the system. Our testing shows this would be correct. The + side of the breaker needs to be connected to the highest potential per the breaker instructions.5.The - side of the PV in breaker goes to the charge controller PV+ input terminal.6.The output of the charge controller is sometimes marked battery+ This terminal is to connect tothe charge controller output breaker. It will not connect to the + or Line side of the breaker.7.The other side of the breaker, + or line connects to the battery plus busbar. This connection isimportant to observe polarity markings. In the event of a charge controller failure, they quite often short internally, which means they are shorting out the battery. If proper polarity is not observed, the breaker may not open and the wiring will burn up.The factory installed red battery plus bus wire is 4AWG, so it is large enough for all breaker sizes.The diagrams above show 63 amp din rail mount breakers. When 80 amp breakers and or DC-GFPare required, those breakers mount on the wall opposite the din rails. Thereare three panel mount breaker slots to accommodate the 80 ampbreakers and DC-GFP. The 80 amp DC-GFP takes up two of the three slots. The third slot will be used for the output of the 80 amp charge controller. The PV input to an 80 amp charge controller could use a 63 amp din rail mount breaker. There is no additional DC-GFP required when using the MidNite Classic controller. The DC-GFP and arc fault protector are built into the Classic controllers.Mounting the inverterThe 6 x 20mm pan head Philips screws for mounting the inverter are taptite (thread forming). Use one of these 6mm screws to pre-tap threads into the steel doors extruded funnel holes. Aluminum doors have press nuts and do not require tapping. Make sure to install all ¼” star washers to bite through the powder coating.One of the best features of the MidNite E-Panel is that one person can do all the lifting.Slip Tab A into Slot B Install inverter cablesInstall the 3.5” bushing as shown protruding up into the inverter side of the door before routing the inverter cables through the door.More tidbits to digestImportant! Torque din rail mount breakers Installing the breaker cover to 20 in lb. Wait one hour and re-torque .Six locations are available for additional 13mm wide breakers. These breakers would normally be field installed for such things as: solar, wind or hydro charge controllers, DC ground fault protector, AC and or DC distribution center and others. Remove the cut outs for the intended breakers. Each 13mm wide breaker requires removal of two cut outs. 17.5mm wide breakers require removal of three cut outs. It is important to torque the terminals to 20 inch pounds. It is highly recommended to go back over all terminations after an hour and also conduct a pull test.Doors installed,plastic conduit installed, wiring complete. Note the battery cable routing. It is important to route cables so the doors close freely without undue force. The left E-Panel battery cables came from above, but could have come fromYou may be surprised that what you thought was a tight connection actually pulls out with little effort. This is caused be a phenomenon called cold flow. Copper is a relatively soft metal and will continue to move under inadequate clamping pressure. A 20 inch pound of torque takes a lot of strength! Use the supplied UL listed plastic 2” x 6” spacers to separate AC and DC breakers if installed on the same din rail. Barriers are required per NEC between AC and DC circuits.MidNite offers 150VDC breakers in 1,2,3,4,5,6,7,8,9,10,12,15,20,30,40,50 and 63 amps. AC breakers are available in 10,15 and 20 amp sizes. Those breakers carry the UL489 and UL489A branch circuit rating. 30 and 50 amp AC breakers are available in UL1077 listed versions, but are not branch circuit rated.For OutBack installations, install the conduit pieces supplied by routing the three wires through the door and conduit before snapping the fittings into place. Snap the top right angle fitting into place first and then the one in the door. Once the length of wire has beenestablished by opening and closing the door, then cut back the three wires as required and hook up to the terminal block. The conduit in the middle of the inverter is for AC wiring. The outer conduit is for remote and battery temp sense wires.Note: Battery cables in a NEC compliant system requires cable listed for use in residential wiring.For installations requiring the OutBack surge arrestor, see pictures below. Note that this surge arrestor is only accommodated on the Stretched OutBack E-Panel.The flex conduit snaps into the sides of the surge arrestor. You will need to get an adapter to go from the 1” conduit hole in the surge arrestor housing to the ¾” flex conduit. These are readily available at your local electrical supply store or Home Depot/Lowes.This basic wiring diagram is mounted on the inside of the hinged door. Elsewhere in these instructions is a slightly expanded version of the E-Panel wiring diagram. There is an AutoCAD version of the expanded wiring diagram at This is provided so that interested parties may download and modify it to tailor their specific system configuration. When stacking two OutBack inverters, it may be required to add the OutBack PSX-240 autotransformer.OutBack and Magnum horizontal stacked systemsE-Panel parts locator, DoorSupplied insulators to achieverequired separation of AC and DCcircuitsE-Panel parts locator, internal Ground to Neutral connectionMagnum MS4448-AE & MS4024-AE system pre-wire with DC-GFPMNE175SM / MNE250SM Samlex E-Panel wiring.MNE175SM Shown.。
Hypertherm FLEXCUT 125 CE 产品说明书
Powerful 125A Air PlasmaFLEXCUT ™ 125 CESteel Fabrication, Pipe Cutting, Structural Publication 04/17© LINCOLN ELECTRIC Cutting Solutions All Rights Reserved www.lincolnelectriccutting.euCE conformCUSTOMER ASSISTANCE POLICYThe Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equipment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occa- sion, purchasers may ask Lincoln Electric for information or advice about their use of our products. Our employees respond to inquiries to the best of their ability based on information provided to them by the customers and the knowledge they may have concerning the application. Our employees, however, are not in a position to verify the information provided or to evaluate the engineering requirements for the particular weldment. Accordingly, Lincoln Electric does not warrant or guarantee or assume any liability with respect to such information or advice. Moreover, the provision of such information or advice does not create, expand, or alter any warranty on our products. Any express or implied warranty that might arise from the information or advice, including any implied warranty of merchantability or any warranty of tness for any customers’ particular purpose is speci cally disclaimed.Lincoln Electric is a responsive manufacturer, but the selection and use of speci c products sold by Lincoln Electric is solely within the control of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric a ect the results obtained in applying these types of fabrication methods and service requirements.Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to for any updated information.FLEXCUT ™ 125 - Specifications10009008007006005004003002001000635050803810254012700125A CuttingFLEXCUT 125FLEXCUT 125125A-12 mm Mild Steel105A-12 mm Mild Steel 45A-2 mm Mild Steel105A CuttingCompetitorCompetitorN u m b e r o f p i e r c e s p e r E l e c t r o d e (20 s e c . C u t T e s t )D r o s s A r e a i n m m 2C u t S p e e d (m m / m i n)ELECTRODE LIFE COMPARISON *CUT QUALITY COMPARISONS *43,93,83,73,63,53,43,3FLEXCUT 125CompetitorB e v e l A n g l e i n D e g r e e sEdge Bevel, 125A, 12 mm Mild SteelDross Level, 125A, 12 mm Mild SteelEdge Profile, 125A, 12 mm Mild SteelCUT SPEED COMPARISON *Lincoln Electric CompetitorFLEXCUT TM 125 CE offers you:Longer Consumable Life • Faster Cut Speeds • Less Edge Bevel • Better Cut Quality and Performance*Claims based upon tests conducted by LINCOLN ELECTRIC in 2016 using an LC125M TorchLess Desired 4° Edge BevelDesired 0° Edge BevelXPLINCOLN ELECTRIC DEUTSCHLAND ZNL der Lincoln Smitweld B.V., Nijmegen Werkstrasse 5 • 64732 Bad Koenig • DeutschlandT: +49 6063 57721 0E-Mail:**************************************www.lincolnelectriccutting.eu1,991,931,871,801,741,671,611,550,1650,1630,1600,1570,1550,1520,1500,1470,1450,1420,140E d g e S u r f a c e F i n i s h i n m m。