手机触摸屏规格书

FILE No:
EDIT:
DATE:
REV:
手写类触摸屏规格承认书
Writing-type Touch panel Specification
品名/Product Name：
机种名/Product Number：手机类之通用标准
客户名称/ CUSTOMER NAME：
客户确认/CUSTOMER APPROVE：
日期/APPROVE DATE:
APPROVE CHECK EDIT
上海雁宇国际贸易有限公司
Shanghai Yanyu Intl. Trade Co., LTD
上海市浦东新区东方路1361号海富花园3号楼3E座
Room 3E,Building 3,Fortune Garden,NO.1361 Dongfang Road,Pudong New District,Shanghai CHINA Code: 200127
TEL:+86-21-6152-4108
FAX:+86-21-6152-8664
CONTENTS
0. 目录Contents
1. 范围 Scope
2. 外形 Shape
2.1 结构 Structure
2.2 外形尺寸 Shape dimension
3. 特性 Characteristics
3.1使用、保存环境Operation and storage
3.2电气特性 Electrical characteristics
3.3 机械特性 Mechanical characteristics
3.4 光学的特性 Optical characteristics
4. 外观检查 Appearance Inspection
4.1 检查规则 Inspection Criteria
4.2检验基准书Inspection standards
4.3 线状异物Linear foreign object
4.4 点状异物Dot-like foreign object
4.5 线状刮伤 Linear scratch
4.6 Film表面没有折伤No fold on film surface
4.7 牛顿环／干渉线Newton ring / Interference fringes
4.8 凸出（包括波状弯曲）Bulge (undulation included) 4.9 Film表面：鱼眼气泡 Film surface: Fish eye Air bubble
4.10 玻璃啐裂和裂纹Chip and Crack of glass
5. 信赖性测试 Reliability Test
5.1 环境实验 Environmental Test
5.2 耐久试验Durability Test
5.3 机械特性测试 Mechanical characteristics Test
6.出货检验事项 Quality Control Notices
7. 其它 Others
8. 保证 Warranty
9. 附件 Attached file
1. 范围 Scope
本规格书为明确规范本公司产品模拟式触控面板性能而订定，当本规格书与其它个别规格书内容有抵触情况发生时，仍以本规格书标准为最优先。

本规格书内容如有项目不足或内容需变更时，须经由会议讨论后另订之。

This specification defines performance of input surfaces for our transparent analog touch panels. In the event of a conflict between this specification and applicable individual specification, this specification takes precedence. Items missing from this specification are to be decided subject to discussion.
2. 外形 Shape
外形、结构和尺寸详见图纸
Shape, structure and dimension are referred to attached drawing
2.1 结构 Structure
结构 Structure 所用材料 Material used 备注 Remark
上线 Top Circuit ITO 薄膜 ITO FILM 亮面防刮; 单层膜;厚度: mm Clear Hard-coating;Single layer Thickness: mm
下线 Bottom Circuit ITO 玻璃 ITO GLASS 厚度: mm Thickness: mm
2.2 外形尺寸 Shape dimension
项目 Item 尺寸 Dimension 单位 Unit
外形尺寸 Out Dimension mm
可视区 View Area mm
动作区 Active Area mm
绝缘点大小及间隔
Spacer Dots & Pitch
mm
3. 特性 Characteristics
3.1使用、保存环境Operation and storage
项目 Item 值(条件) Value (conditions) 备注 Remark
使用温度范围 Operation temperature
& Humidity 湿度 20％～90％：非结露状态
－10℃～60℃
Humidity：20-90％ non dew
condensation
－10℃～60℃
单体状态下
In a single substance
保存温度范围 Storage temperature & Humidity 湿度 20％～90％：非结露状态
－20℃～70℃
Humidity：20-90％ non dew
condensation
－20℃～70℃
单体状态下
In a single substance
3.2电气特性 Electrical characteristics
项目Item 值 Value 备注 Remark 最大电压 Maximum voltage 直流7V DC7V
Ｘ方向(Film面)：Ω
X direction [Film side]:Ω
端子间阻抗
Resistance between terminals
Ｙ方向(Glass面)：Ω
Y direction [Glass side]:Ω
Ｘ方向：±1.5% 以内
X direction: within ±1.5% 直线性
Linearity Ｙ方向：±1.5% 以内
Y direction: within ±1.5% 测试方法如图所示 Testing method as following drawing
3.3 机械特性 Mechanical characteristics
项目 Item 性能 Performance Remark 备注
输入方法 Input method
用专用笔或手指触控
Use of an exclusive pen or finger
专用笔
Exclusive pen
80g 以下
80g or less
使用笔来进行操作或测试时，其笔尖端
材质必须符合以下条件：笔尖材质：
Polyacetal（聚纤维酯）
笔端：笔径Φ3.0 mm 、表面弧度
SR 0.8 mm
Operation and measurement with a
pen must be carried out under the
following tip conditions : Stylus pen
material:POM (Polyacetal)
Tip:Diameter3.0mm, SR0.8mm
动作荷重 Load upon operation
手指输入 Finger
80g 以下
80g or less
使用特定工具来代替手指进行操作和
测试，其材质必须符合以下条件
Operations and measurement
methods simulated for a finger must
be carried out under the following tip
conditions :
材 质：硅橡胶(硬度: 30°Hs)
顶端：笔径Φ12mm、表面弧度
SR12.5mm
Material: Silicon rubber(Hardness :
30°Hs)
Tip: Diameter12.0mm, SR12.5mm
表面硬度 Surface hardness
铅笔硬度3H 以上
Pencil hardness: 3H or more
依据JIS K5600试验方法
It complies with the way of test
method JIS K5600
备注: 由绝缘点的大小及间距来决定操作压力的大小。

Remark: The operation force depending on the diameter & pitch of spacer dot.
3.4 光学的特性 Optical characteristics
项目 Item 性能 Performance 备注 Remark
Total light transmittance 全光线透过率
%以上
% or more
JIS K7105
雾值 Haze
%以下
% or less
JIS K7136
Film规格Film specification
亮面 ，有一定表面硬度 Clear type with hard-coating surface
4. 外观检查 Appearance Inspection
4.2 检验基准 Inspection standards
产品可视范围外若有裂缝，刮伤，异物等外观不良，不影响产品电气特性的，也可接受。

For areas outside the visible range, it is acceptable if there is no crack, scratch, or foreign objects that can
greatly affect the electric performance of this product.
限度样品用于本基准中未尽描述的裂缝，刮伤或者异物等外观不良。

Limit samples shall be used for cracks, scratch, or foreign objects which are not described in this standard.
4.3 线状异物（W=宽度、L=长度） Linear foreign object (W=Width, L=Length)
宽度 Width （mm）长度 Length
（mm）
基准 Judge criterion 备注 Remark
W≦0.05 不计 Ignored 0.05＜W≦0.09 L≦5 1个 1 object
W＞0.09 不接受 Reject
4.4 点状异物(D=长径)Dot-like foreign object (D = longest diameter)
平均直径
Average diameter
（mm ）
基准 Judge criterion 备注 Remark D ≦0.10 不计 Ignored
0.10＜D ≦0.15
2个或2个以下(异物间隔小于10mm ，不接受)
2 objects or less, with the Failure under distance 10mm
0.15＜D ≦0.20 1个 1 object D ＞0.20
不接受 Reject
2个以上缺陷 Up to total two
defects
4.5 线状刮伤（W=宽度、L=长度） Linear scratch (W=Width, L=
Length)
刮痕
宽度（mm ）
长度（mm ）
基准 注意
W ＜0.03
不计 Ignored 0.03≦W ≦0.05 L ≦5 不计 Ignored
0.05＜W ≦0.1 L ≦5 2个或2个以下(异物间隔小于10mm ，不接受)
2 objects or less, with the Failure under distance 10mm
W ＞0.1
不接受 Reject
2个以上缺陷
Up to total two
defects
4.6 Film 表面没有折伤 No fold on film surface
4.7 牛顿环／干渉线 Newton ring / Interference fringes 根据 4.1外观检查方法确认 To be confirmed according to No.4.1inspection of appearance 4.8 凸出（包括波状弯曲）Bulge (undulation included)
膜鼓起在0.40mm 高度范围内判定为合格品。

The ITO film Bulged below
0.4mm or less
0.4mm或以下
4.9 Film表面：鱼眼气泡凹痕 Film surface: Fish eye Air bubble
Dent
鱼眼，凹痕与气泡
平均直径
Average diameter（mm）
基准 Judge criterion 备注 Remark D≦0.20 不计 Ignored
0.20＜D≦0.35
最多6个MAX 6 Pieces
0.35＜D≦0.60
最多2个MAX 2 Pieces
D＞0.60 不接受 Reject
5. 信赖性实验内容 Reliability Test
5.1 环境实验 Environment Test
项目 Items
内容
Contents
备注 Remark
高温保存 High temperature preservation (1)温度70℃,放置120小时；(2)室温放置24小时以上；(3)然后测量以下项目：
(1)Store at 70℃ for 120 hours; (2) Keep at a room temperature for more than 24 hours; and (3) Measure (satisfy) the following items:
端子间阻抗：参照电气特性栏Resistance between terminals: refer to electrical characteristics item; 直线性：参照电气特性栏 Linearity: refer to electrical characteristics item; 绝缘阻抗：参照电气特性栏 Insulation resistance: refer to electrical characteristics item
低温保存 Low temperature preservation (1)温度－30℃,放置120小时；(2)室温放置24小时以上；(3)然后测量以下项目：
(1)Store at -30 ℃for 120 hours; (2) Keep at a room temperature for more than 24 hours; and (3) Measure (satisfy) the following items:
端子间阻抗：参照电气特性栏Resistance between terminals: refer to electrical characteristics item; 直线性：参照电气特性栏 Linearity: refer to electrical characteristics item; 绝缘阻抗：参照电气特性栏 Insulation resistance: refer to electrical characteristics item
高温高湿保存 High temperature & high humidity (1)温度60℃湿度90%,放置120小时；(2)室温放置24小时以上(3)然后测量以下项目:
(1)Store at 60℃and 90% RH for 120 hours; (2) Keep at a room temperature for more than 24 hours; and (3) Measure (satisfy) the following items:
端子间阻抗：参照电气特性栏Resistance between terminals: refer to electrical characteristics item; 直线性：参照电气特性栏 Linearity: refer to electrical characteristics item; 绝缘阻抗：参照电气特性栏 Insulation resistance: refer to electrical characteristics item
冷热冲击测试Heat shook test (1)－30℃(60 分钟)→80℃(60 分钟)共10次循环;(2)室温放置24小时以上;(3)然后测量以下项目：
(1)－30℃(60min)→80℃(60min)total 10 cycles, (2) Keep at a room temperature for more than 24 hours; and (3) Measure (satisfy) the following items:
端子间阻抗：参照电气特性栏Resistance between terminals: refer to electrical characteristics item; 直线性：参照电气特性栏 Linearity: refer to electrical characteristics item; 绝缘阻抗：参照电气特性栏 Insulation resistance: refer to electrical characteristics item
5.2 Durability Test 耐久试验
项目 Items 内容 Contents
备注Remark
耐敲击 Hitting Durability (1)使用Placental (POM)铅笔(R0.8) 敲击100 万次。

(2)然后测量以下项目：
(1)Hit 1,000,000 times with a Placental (POM) pencil (R0.8); and (2) Measure (satisfy) the following items:
荷重：250gf Load:250gf
速度：2次／sec Speed: 2 times/sec
端子间阻抗：参照电气特性栏Resistance between terminals: refer to electrical characteristics item; 直线性：参照电气特性栏 Linearity: refer to electrical characteristics item; 绝缘阻抗：参照电气特性栏 Insulation resistance: refer to electrical characteristics item
5.3 机械特性测试 Mechanical characteristics Test (1) 操作压力测试 Operation force Test Ⅰ.笔输入 Operation with a exclusive pen
材质：聚纤维酯 Pen Material: Polyacetal
笔端 ：笔 径 Φ3.0mm 表面弧度：SR0.8mm Tip: Φ3.0 mm, SR 0.8mm Ⅱ.手指输入 Operation with a finger
材质：硅橡胶（硬度：30°Hs ） Material: Silicon Rubber (Hardness: 30°Hs) 顶端：笔 径Φ12 mm 表面弧度：SR12.5 mm Tip: Φ12mm, SR 12.5mm
方法：5V(DC)电压加于产品X 方向，测试头在产品AA 区内缩3mm 区域内五点施力（如下图），输出电压稳定（误差±5%），计算五点压力平均值，即为操作压力。

Method: Force 5V (DC) voltage to X-axis direction of touch panel. Force five dots in shrinks 3mm from
the AA verge with test tip. (As the following chart) If the output voltage is steady-going, then calculate the force mean value of these five dots, which is operation force.
Ⅲ.操作压力范围：T/P AA 区域内缩3mm 保证80g Max ；T/P AA 区域内缩5mm 保证50g Max 。

Range of operation force: Ensured max 80gf should be more than 3mm inside from the boundary of active area; ensured max 50gf should be more than 5mm inside from the boundary of active area. (2) 表面硬度测试：依据JIS K5600试验方法 Surface Hardness Test : Which according to the test method
JIS K5600.
方法：硬度铅笔笔心距离固定5mm 来划线（直线长约30~40mm ），角度45°，使其垂直下压约500g （如图）。

划线后，用无尘布沾上酒精擦去铅笔笔迹，观察划线处是否有刮痕存在。

Method: Slide the pencil each line with granularity 5mm （beeline length about 30～40mm ）and 45°
angle
，Force vertically approx. 500g （as the following chart). After sliding, wipe off the pencil trace with clean soft cloth moistened with ethanol, and then check whether or not existing the scratch on the sliding place.
判定：以硬度铅笔笔心划线处是否有刮痕存在评判。

若无刮痕表示此硬度达到测试铅笔的硬度。

Judgment: take the following situation as a criterion: whether or not existing disordered sliding trace
on the pencil sliding place. If have no disordered trace should be denoted that the surface hardness up to the hardness of the testing pen.
铅笔硬度等级：H 2H 3H 4H 5H
(3) 耐冲击实验 Impact resistance Test
要求：根据玻璃厚度的不同测试落下高度，适用于FILM+GLASS 类型的产品。

Requirement: Test the dropping height according to different glass thickness. Sample to be tested is
only Film + Glass type.
方法：将一个Φ11mm 5.5g 钢球于1.3m 高做自由落体运动撞击待测物体中心表面一次。

(0.7玻璃板厚
高度为1.0m)
Method: No glass breaks when 5.5 g, Φ11mm steel ball is dropped vertically on the center of
product surface from 1.3m height at one time in accordance with 1.1mm thickness. (0.7mm
glass thickness should be in accordance with 1.0m height)
判定：产品完好无破裂，满足端子间阻抗、直线性、绝缘阻抗要求。

Judgement ：No break or crack on product. The requirement " Terminal resistance, linearity,
Insulation resistance”shall be satisfied.
(注意：在待测物下方四周垫一层3mm 厚的泡棉。

)
(Remark: Under the product to be tested, Underlay one cushion which is 3mm thickness and the size is less than the product)
11∮㎜
(4) 耐静压测试 Static Load Resistance
方法：使用拉压力计的平头测试头(Φ10mm)对产品中心表面施加5~10kgf 持续30Sec ，产品不破裂。

Method: No glass break or crack after pressing the product vertically on the center of film surface
with 5-10kgf by Φ10mm testing pen of the manometer with 30 Sec. continuance. Sample
to be tested is only Film + Glass type.
判定：产品完好无破裂，满足端子间阻抗、直线性、绝缘阻抗要求。

Judgement: No break or crack on product. The requirement " Terminal resistance, linearity,
Insulation resistance”shall be satisfied.
(5) 耐振动测试 Vibration Resistance
Ⅰ. 操作状态：在X 、Y 、Z 各方向以2m/s 2的加速度，10~55Hz(1分钟)的频率振动，持续30分钟，满足端
子间阻抗、直线性、绝缘阻抗要求。

I. In operation:The requirements " Terminal resistance, linearity, Insulation resistance”shall be
satisfied, when sweep vibration of 2m/S², 10Hz to 55Hz (1 min.) is given for 30 min.
each in the direction of X,Y,Z.
Ⅱ. 非操作状态：在X 、Y 、Z 各方向以20m/s 2的加速度，10~55Hz(1分钟)的频率振动，持续30分钟，满足
端子间阻抗、直线性、绝缘阻抗要求。

II. Not in operation:The requirements " Terminal resistance, linearity, Insulation resistance”shall be
satisfied, when sweep vibration of 20m/S², 10Hz to 55Hz (1 min.) is given for 30 min.
each in the direction of X,Y,Z.
(6) 包装跌落测试 Package drop
方法：使包装在90cm 高处(1角、2棱、4面)依次各做一次自由落体实验。

Method: Make the package drops test about seven times from 90cm height.(each in one corner,
two arris and four surface )
判定：包装完好，产品无破损，满足端子间阻抗、直线性、绝缘阻抗要求。

Judgement: No break or crack on product. The requirement " Terminal resistance, linearity,
Insulation resistance”shall be satisfied.
6. 出货检验事项 Notices on Quality Control
每批交货实施下列检查, 并附检查报告
We here shall make the quality inspection for each lot products as the following, and attach inspection report as well :
(1) 外观 Appearance inspection
(2) 操作压力测试 Operation force test
(3) 电气特性 Electric characteristics
(4) 回路阻抗 Terminal resistance
7. 其它 Others
(1)触摸屏的信赖性测试应放置在平板上，在非通电状态下进行。

The reliability test shall be done with the touch panel put on a flat board, and with the circuit open. (2)各实验项目应在标准状态下（23℃±5℃、60%±10%RH）进行，除非有单独的说明。

Each test shall be done at a normal condition (23℃±5℃、60%±10%RH) unless otherwise specified separately.
8. 保证 Warranty
上海雁宇国际贸易有限公司对所有制造的成品在出货后一年内保证此规格书上所提到的项目
Shanghai Yanyu Intl. Trade Co., LTD warrants that all manufactured product to this specification for one year from date of purchase.
9. 附件 Attached file
9.1 工程图 Drawing
9.2 包装图 Packing Drawing
9.3 使用说明及注意事项Illustrate & Operation Instructions。