NC7SP14P5X, 规格书,Datasheet 资料
合集下载
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Supply Voltage (VCC) DC Input Voltage (VIN) DC Output Voltage (VOUT) HIGH or LOW State (Note 2) VCC = 0V DC Input Diode Current (IIK) VIN < 0V DC Output Diode Current (IOK) VOUT < 0V VOUT > VCC DC Output Source/Sink Current (IOH/IOL) DC VCC or Ground Current per Supply Pin (ICC or Ground) Storage Temperature Range (TSTG)
0.9V to 3.6V 0.0V to 3.6V 0V to VCC 0V to 3.6V
±2.6 mA ± 2.1 mA ± 1.5 mA ± 1 mA ±0.5 mA ±20 µA −40°C to +85°C
DC Electrical Characteristics
Symbol VP Parameter Positive Threshold Voltage VCC (V) 0.90 1.10 1.40 1.65 2.30 3.00 VN Negative Threshold Voltage 0.90 1.10 1.40 1.65 2.30 3.00 VH Hysteresis Voltage 0.90 1.10 1.40 1.65 2.30 3.00 TA = +25°C Min 0.3 0.4 0.5 0.7 1.0 1.5 0.1 0.15 0.2 0.25 0.4 0.6 0.07 0.08 0.09 0.10 0.25 0.60 Max 0.6 1.0 1.2 1.5 1.9 2.6 0.6 0.7 0.8 0.9 1.15 1.5 0.5 0.6 0.8 1.0 1.1 1.8 TA = −40°C to +85°C Min 0.3 0.4 0.5 0.7 1.0 1.5 0.1 0.15 0.2 0.25 0.4 0.6 0.07 0.08 0.09 0.10 0.25 0.60 Max 0.6 1.0 1.2 1.5 1.9 2.6 0.6 0.7 0.8 0.9 1.15 1.5 0.5 0.6 0.8 1.0 1.1 1.8 V V V Units Conditions
3
芯天下--/
NC7SP14
DC Electrical Characteristics
Symbol VOH Parameter HIGH Level Output Voltage VCC (V) 0.90 1.10 ≤ VCC ≤ 1.30 1.40 ≤ VCC ≤ 1.60 1.65 ≤ VCC ≤ 1.95 2.30 ≤ VCC ≤ 2.70 3.00 ≤ VCC ≤ 3.60 1.40 ≤ VCC ≤ 1.60 1.65 ≤ VCC ≤ 1.95 2.30 ≤ VCC ≤ 2.70 3.00 ≤ VCC ≤ 3.60 VOL LOW Level Output Voltage 0.90 1.10 ≤ VCC ≤ 1.30 1.40 ≤ VCC ≤ 1.60 1.65 ≤ VCC ≤ 1.95 2.30 ≤ VCC ≤ 2.70 3.00 ≤ VCC ≤ 3.60 1.10 ≤ VCC ≤ 1.30 1.40 ≤ VCC ≤ 1.60 1.65 ≤ VCC ≤ 1.95 2.30 ≤ VCC ≤ 2.70 3.00 ≤ VCC ≤ 3.60 IIN IOFF ICC Input Leakage Current Power Off Leakage Current Quiescent Supply Current 0.90 to 3.60 0 0.90 to 3.60
±2.6 mA @ 3.00V VCC ±2.1 mA @ 2.30V VCC ±1.5 mA @ 1.65V VCC ±1.0 mA @ 1.40V VCC ±0.5 mA @ 1.10V VCC ±20 µA @ 0.9V VCC
s Uses patented Quiet Series noise/EMI reduction circuitry s Ultra small MicroPak leadfree package s Ultra low dynamic power
TinyLogic is a registered trademark, and Quiet Series, and MicroPak are trademarks of Fairchild Semiconductor Corporation.
© 2004 Fairchild Semiconductor Corporation
−0.5V to +4.6V −0.5V to +4.6V −0.5V to VCC +0.5V −0.5V to 4.6V ±50 mA −50 mA +50 mA ± 50 mA ± 50 mA −65°C to +150 °C
Recommended Operating Conditions (Note 3)
Battery Life vs. VCC Supply Voltage
TinyLogic ULP and ULP-A with up to 50% less power consumption can extend your battery life significantly. Battery Life = (Vbattery *Ibattery*.9)/(Pdevice)/24hrs/day Where, Pdevice = (ICC * VCC) + (CPD + C L) * VCC2 * f Assumes ideal 3.6V Lithium Ion battery with current rating of 900mAH and derated 90% and device frequency at 10MHz, with CL = 15 pF load
Ordering Code:
Order Number NC7SP14P5X NC7SP14L6X Package Number MAA05A MAC06A Product Code Top Mark P14 K3 Package Description 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide 6-Lead MicroPak, 1.0mm Wide Supplied As 3k Units on Tape and Reel 5k Units on Tape and Reel
The NC7SP14 is a single inverter with Schmitt trigger input from Fairchild’s Ultra Low Power (ULP) Series of TinyLogic. Ideal for applications where battery life is critical, this product is designed for ultra low power consumption within the VCC operating range of 0.9V to 3.6V VCC . The internal circuit is composed of a minimum of inverter stages, including the output buffer, to enable ultra low static and dynamic power. The NC7SP14, for lower drive requirements, is uniquely designed for optimized power and speed, and is fabricated with an advanced CMOS technology to achieve best in class speed operation while maintaining extremely low CMOS power dissipation.
Features
s 0.9V to 3.6V VCC supply operation s 3.6V overvoltage tolerant I/O’s at VCC from 0.9V to 3.6V s tPD 4.0 ns typ for 3.0V to 3.6V VCC 5.0 ns typ for 2.3V to 2.7V VCC 6.0 ns typ for 1.65V to 1.95V VCC 7.0 ns typ for 1.40V to 1.60V VCC 11.0 ns typ for 1.10V to 1.30V VCC 27.0 ns typ for 0.90V VCC s Power-Off high impedance inputs and outputs s Static Drive (IOH/IOL)
NC7SP14 TinyLogic ULP Inverter with Schmitt Trigger Input
June 2002 Revised March 2004
NC7SP14 TinyLogic ULP Inverter with Schmitt Trigger Input
General Description
H = HIGH Logic Level L = LOW Logic Level
Function Table
Output Y H L
(Top Thru View)
2
芯天下--/
NC7SP14
Absolute Maximum Ratings(Note 1)
7SP14
Logic Symbol
IEEE/IEC
Connection Diagrams
Pin Assignments for SC70
Pin Descriptions
Pin Names A Y NC Description Input Output No Connect (Top View) Pad Assignments for MicroPak Y=A Inputs A L H
Supply Voltage Input Voltage (VIN) Output Voltage (VOUT) HIGH or LOW State VCC = 0V Output Current in IOH/IOL VCC = 3.0V to 3.6V VCC = 2.3V to 2.7V VCC = 1.65V to 1.95V VCC = 1.40V to 1.60V VCC = 1.10V to 1.30V VCC = 0.9V Free Air Operating Temperature (TA) Minimum Input Edge Rate (∆t/∆V) VIN = 0.8V to 2.0V, VCC = 3.0V 10 ns/V
oneiccomwwwfairchildsemicom4nc7sp14dcelectricalcharacteristicscontinuedacelectricalcharacteristicssymbolparametervccta25cta?40cto85cunitsconditionsvminmaxminmaxvohhighlevel090vcc?01vcc?01vioh?20?aoutputvoltage110vcc130vcc?01vcc?01140vcc160vcc?01vcc?01165vcc195vcc?01vcc?01230vcc270vcc?01vcc?01300vcc360vcc?01vcc?01110vcc130075xvcc070xvccioh?05ma140vcc160107099ioh?1ma165vcc195124122ioh?15ma230vcc270195187ioh?21ma300vcc360261255ioh?26mavollowlevel0900101viol20?aoutputvoltage110vcc1300101140vcc1600101165vcc1950101230vcc2700101300vcc3600101110vcc130030xvcc030xvcciol05ma140vcc160031037iol1ma165vcc195031035iol15ma230vcc270031033iol21ma300vcc360031033iol26maiininputleakagecurrent090to3600105?a0vi36vioffpoweroffleakagecurrent00505?a0vivo36viccquiescentsupplycurrent090to3600909?avivccorgndsymbolparametervccta25cta?40cto85cunitsconditionsfigurenumbervmintypmaxminmaxtphlpropagationdelay09027nsfigures12tplh110vcc130351121830343140vcc16025714820150cl10pf165vcc19520612015122rl1m?230vcc270155941099300vcc360104831090tphlpropag
Note 1: Absolute Maximum Ratings: are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table will define the conditions for actual device operation. Note 2: IO Absolute Maximum Rating must be observed. Note 3: Unused inputs must be held HIGH or LOW. They may not float.
0.9V to 3.6V 0.0V to 3.6V 0V to VCC 0V to 3.6V
±2.6 mA ± 2.1 mA ± 1.5 mA ± 1 mA ±0.5 mA ±20 µA −40°C to +85°C
DC Electrical Characteristics
Symbol VP Parameter Positive Threshold Voltage VCC (V) 0.90 1.10 1.40 1.65 2.30 3.00 VN Negative Threshold Voltage 0.90 1.10 1.40 1.65 2.30 3.00 VH Hysteresis Voltage 0.90 1.10 1.40 1.65 2.30 3.00 TA = +25°C Min 0.3 0.4 0.5 0.7 1.0 1.5 0.1 0.15 0.2 0.25 0.4 0.6 0.07 0.08 0.09 0.10 0.25 0.60 Max 0.6 1.0 1.2 1.5 1.9 2.6 0.6 0.7 0.8 0.9 1.15 1.5 0.5 0.6 0.8 1.0 1.1 1.8 TA = −40°C to +85°C Min 0.3 0.4 0.5 0.7 1.0 1.5 0.1 0.15 0.2 0.25 0.4 0.6 0.07 0.08 0.09 0.10 0.25 0.60 Max 0.6 1.0 1.2 1.5 1.9 2.6 0.6 0.7 0.8 0.9 1.15 1.5 0.5 0.6 0.8 1.0 1.1 1.8 V V V Units Conditions
3
芯天下--/
NC7SP14
DC Electrical Characteristics
Symbol VOH Parameter HIGH Level Output Voltage VCC (V) 0.90 1.10 ≤ VCC ≤ 1.30 1.40 ≤ VCC ≤ 1.60 1.65 ≤ VCC ≤ 1.95 2.30 ≤ VCC ≤ 2.70 3.00 ≤ VCC ≤ 3.60 1.40 ≤ VCC ≤ 1.60 1.65 ≤ VCC ≤ 1.95 2.30 ≤ VCC ≤ 2.70 3.00 ≤ VCC ≤ 3.60 VOL LOW Level Output Voltage 0.90 1.10 ≤ VCC ≤ 1.30 1.40 ≤ VCC ≤ 1.60 1.65 ≤ VCC ≤ 1.95 2.30 ≤ VCC ≤ 2.70 3.00 ≤ VCC ≤ 3.60 1.10 ≤ VCC ≤ 1.30 1.40 ≤ VCC ≤ 1.60 1.65 ≤ VCC ≤ 1.95 2.30 ≤ VCC ≤ 2.70 3.00 ≤ VCC ≤ 3.60 IIN IOFF ICC Input Leakage Current Power Off Leakage Current Quiescent Supply Current 0.90 to 3.60 0 0.90 to 3.60
±2.6 mA @ 3.00V VCC ±2.1 mA @ 2.30V VCC ±1.5 mA @ 1.65V VCC ±1.0 mA @ 1.40V VCC ±0.5 mA @ 1.10V VCC ±20 µA @ 0.9V VCC
s Uses patented Quiet Series noise/EMI reduction circuitry s Ultra small MicroPak leadfree package s Ultra low dynamic power
TinyLogic is a registered trademark, and Quiet Series, and MicroPak are trademarks of Fairchild Semiconductor Corporation.
© 2004 Fairchild Semiconductor Corporation
−0.5V to +4.6V −0.5V to +4.6V −0.5V to VCC +0.5V −0.5V to 4.6V ±50 mA −50 mA +50 mA ± 50 mA ± 50 mA −65°C to +150 °C
Recommended Operating Conditions (Note 3)
Battery Life vs. VCC Supply Voltage
TinyLogic ULP and ULP-A with up to 50% less power consumption can extend your battery life significantly. Battery Life = (Vbattery *Ibattery*.9)/(Pdevice)/24hrs/day Where, Pdevice = (ICC * VCC) + (CPD + C L) * VCC2 * f Assumes ideal 3.6V Lithium Ion battery with current rating of 900mAH and derated 90% and device frequency at 10MHz, with CL = 15 pF load
Ordering Code:
Order Number NC7SP14P5X NC7SP14L6X Package Number MAA05A MAC06A Product Code Top Mark P14 K3 Package Description 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide 6-Lead MicroPak, 1.0mm Wide Supplied As 3k Units on Tape and Reel 5k Units on Tape and Reel
The NC7SP14 is a single inverter with Schmitt trigger input from Fairchild’s Ultra Low Power (ULP) Series of TinyLogic. Ideal for applications where battery life is critical, this product is designed for ultra low power consumption within the VCC operating range of 0.9V to 3.6V VCC . The internal circuit is composed of a minimum of inverter stages, including the output buffer, to enable ultra low static and dynamic power. The NC7SP14, for lower drive requirements, is uniquely designed for optimized power and speed, and is fabricated with an advanced CMOS technology to achieve best in class speed operation while maintaining extremely low CMOS power dissipation.
Features
s 0.9V to 3.6V VCC supply operation s 3.6V overvoltage tolerant I/O’s at VCC from 0.9V to 3.6V s tPD 4.0 ns typ for 3.0V to 3.6V VCC 5.0 ns typ for 2.3V to 2.7V VCC 6.0 ns typ for 1.65V to 1.95V VCC 7.0 ns typ for 1.40V to 1.60V VCC 11.0 ns typ for 1.10V to 1.30V VCC 27.0 ns typ for 0.90V VCC s Power-Off high impedance inputs and outputs s Static Drive (IOH/IOL)
NC7SP14 TinyLogic ULP Inverter with Schmitt Trigger Input
June 2002 Revised March 2004
NC7SP14 TinyLogic ULP Inverter with Schmitt Trigger Input
General Description
H = HIGH Logic Level L = LOW Logic Level
Function Table
Output Y H L
(Top Thru View)
2
芯天下--/
NC7SP14
Absolute Maximum Ratings(Note 1)
7SP14
Logic Symbol
IEEE/IEC
Connection Diagrams
Pin Assignments for SC70
Pin Descriptions
Pin Names A Y NC Description Input Output No Connect (Top View) Pad Assignments for MicroPak Y=A Inputs A L H
Supply Voltage Input Voltage (VIN) Output Voltage (VOUT) HIGH or LOW State VCC = 0V Output Current in IOH/IOL VCC = 3.0V to 3.6V VCC = 2.3V to 2.7V VCC = 1.65V to 1.95V VCC = 1.40V to 1.60V VCC = 1.10V to 1.30V VCC = 0.9V Free Air Operating Temperature (TA) Minimum Input Edge Rate (∆t/∆V) VIN = 0.8V to 2.0V, VCC = 3.0V 10 ns/V
oneiccomwwwfairchildsemicom4nc7sp14dcelectricalcharacteristicscontinuedacelectricalcharacteristicssymbolparametervccta25cta?40cto85cunitsconditionsvminmaxminmaxvohhighlevel090vcc?01vcc?01vioh?20?aoutputvoltage110vcc130vcc?01vcc?01140vcc160vcc?01vcc?01165vcc195vcc?01vcc?01230vcc270vcc?01vcc?01300vcc360vcc?01vcc?01110vcc130075xvcc070xvccioh?05ma140vcc160107099ioh?1ma165vcc195124122ioh?15ma230vcc270195187ioh?21ma300vcc360261255ioh?26mavollowlevel0900101viol20?aoutputvoltage110vcc1300101140vcc1600101165vcc1950101230vcc2700101300vcc3600101110vcc130030xvcc030xvcciol05ma140vcc160031037iol1ma165vcc195031035iol15ma230vcc270031033iol21ma300vcc360031033iol26maiininputleakagecurrent090to3600105?a0vi36vioffpoweroffleakagecurrent00505?a0vivo36viccquiescentsupplycurrent090to3600909?avivccorgndsymbolparametervccta25cta?40cto85cunitsconditionsfigurenumbervmintypmaxminmaxtphlpropagationdelay09027nsfigures12tplh110vcc130351121830343140vcc16025714820150cl10pf165vcc19520612015122rl1m?230vcc270155941099300vcc360104831090tphlpropag
Note 1: Absolute Maximum Ratings: are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table will define the conditions for actual device operation. Note 2: IO Absolute Maximum Rating must be observed. Note 3: Unused inputs must be held HIGH or LOW. They may not float.