FBWINBLi智能水浸传感器使用说明书
水浸传感器使用说明书
水浸传感器使用说明书文档版本：1. 产品介绍 (3)2. 产品选型 (4)3. 设备安装说明 (5)4. 配置软件安装及使用 (6)5. 通信协议 (7)6. 常见问题及解决办法 (9)7. 联系方式 (9)8. 文档历史 (10)9. 附录：各种壳体尺寸 (10)1. 产品介绍产品概述该水浸探测器广泛适用于通讯基站、宾馆、饭店、机房、图书馆、档案库、仓库、设备机柜以及其它需积水报警的场所，传感器内输入电源，感应线，信号输出三部分完全隔离。
安全可靠，外观美观，安装方便。
功能特点我公司采用交变电流采集积水的电感参数，准确区分是否发生水浸，甚至可以区分纯净水与自来水（默认以自来水为检测对象，若要检测纯净水请特殊说明）。
因为采用交变电流检测，电极即使长时间浸泡也不会产生电泳极化，不依赖特殊电极，做到寿命长、检测可靠。
---此技术为我公司专利，已获专利局授权，凡仿冒者我公司保留追究其法律责任的权利。
主要技术指标供电电源：10~30V DC 存储环境：-20℃~80℃ 误报率：<100ppm 继电器输出：常开触点系统框架图系统方案图2. 产品选型壁挂王字壳卡轨壳3. 设备安装说明设备安装前检查设备清单：■水浸传感器设备1台■合格证、保修卡、售后服务卡等■12V/2A防水电源1台（选配）■USB转485（选配）接线电源及485信号接线宽电压电源输入10~30V均可。
485信号线接线时注意A\B两条线不能接反，总线上多台设备间地址不能冲突。
继电器接口接线设备标配是具有1路继电器输出，两条出线为常开触点。
具体型号接线卡轨壳接线出485-B（蓝色）4. 配置软件安装及使用软件选择打开资料包，选择“调试软件”---“485参数配置软件”，找到打开即可。
参数设置①、选择正确的COM口（“我的电脑—属性—设备管理器—端口”里面查看COM端口），下图列举出几种不同的485转换器的驱动名称。
②、单独只接一台设备并上电，点击软件的测试波特率，软件会测试出当前设备的波特率以及地址，默认波特率为4800bit/s,默认地址为0x01。
485型水浸传感器说明书
水浸传感器说明书 485型水浸传感器使用说明书水浸传感器说明书 第1章产品简介1.1产品概述水浸传感器主要用来检测是否出现漏水情况，本传感器采用交流阻抗测量方式，电极使用寿命长，不会出现氧化问题。
该水浸传感器广泛适用于通讯基站、宾馆、饭店、机房、图书馆、档案库、仓库、设备机柜以及其它需积水报警的场所。
1.2功能特点采用交流阻抗测量形式，交流阻抗方式可以有效避免电极发生氧化电解，极大的提高寿命。
漏水测量结果精准，误报率几乎为零。
1.3主要参数直流供电12V-24V DC开关量类型常开触点检测对象各类型水溶液耗电≤0.15W（@12V DC,25℃）开关量工作功率120VAC/24VDC水浸传感器说明书 1.4系统框架图本传感器可以连接单独使用，首先使用12V直流电源供电，设备可以直接连接带有485接口的PLC，可以通过485接口芯片连接单片机。
通过后文指定的modbus协议对单片机和PLC进行编程即可配合传感器使用。
同时使用USB转485即可与电脑连接，使用我公司提供的传感器配置工具进行配置和测试。
本产品也可以多个传感器组合在一条485总线使用，在进行485总线组合时请遵守“485总线现场接线守则”（见水浸传感器说明书 附录）。
理论上一条总线可以接16个以上的485传感器，如果需要接更多的485传感器，可以使用485中继器扩充更多的485设备，另一端接入带有485接口的PLC、通过485接口芯片连接单片机，或者使用USB转485即可与电脑连接，使用我公司提供的传感器配置工具进行配置和测试。
水浸传感器说明书 第2章硬件连接2.1设备安装前检查安装设备前请检查设备清单：名称数量高精度传感器1台12V防水电源1台（选配）USB转485设备1台（选配）保修卡/合格证1份2.2接口说明电源接口为宽电压电源输入12-24V均可。
485信号线接线时注意A/B两条线不能接反，总线上多台设备间地址不能冲突。
水浸传感器说明书线色说明电源棕色电源正（12-24VDC）黑色电源负通信黄色485-A蓝色485-B开关量白色开关量灰色开关量注意事项：请注意不要接错线序，错误的接线会导致设备烧毁。
Pulse Level Cellular 倾斜水位传感器说明书
3A8551CEN Installation, Operation, and ServicePulse® Level CellularTank Level MonitorMeasures the distance between the device and the surface of the fluid to determine the volume of fluid within a tank. For use only with Pulse Level. Intended fluids: oil, diesel, waste oil, automatic transmission fluid (ATF), kerosene, anti-freeze, windshield washer solution, waste water, and DEF. For professional use only. Not suitable for tank overfill protection.Not approved for use in explosive atmospheres or hazardous (classified) locations.Model DescriptionRadioApprovals25T461Pulse Level CellularNorth America FCC, IC133620Pulse Level CellularInternatiolnalCE, RCMImportant Safety InstructionsRead all warnings and instructions in thismanual and in all related Pulse manualsbefore using the equipment.Save allinstructions.This Tank Level Monitor (TLM) contains FCC ID XMR201707 BG96. This device complies with Part 15 of theFCC Rules. Operation is subject to the following twoconditions:•This device may not case harmful interference.•This device must accept any interference received,including interference that may cause undesiredoperation.Installation23A8551CInstallationSet UpRegister TLM to Tank in Pulse Level SoftwareNavigate to URL: This device requires access to a cellular network to work, and can be activated in Pulse Level. Refer to Pulse Level terms of service in the About section of the software.After creating user, organization, branch and site,navigate to Devices (located in the upper right corner of the screen). Associate the device to your organization by entering the serial number. When you create a tank for the site, the device will be assignable.Assign the TLM serial number to a tank in Pulse Level.Activation1.Hold the magnet (supplied) to the Hot Spot directlyunder the LED to activate the device (F IG . 1).2.Keep holding the magnet to the Hot Spot. The LEDwill flash green, and then flash red. Then the red light will stay lit.3.Remove the magnet.4.While the red light is illuminated, a series of beepsoccur as the device connects.5.Successfully connecting is indicated by ahigh/low/high series of beeps that indicate the data is being sent to Pulse Level. The LED turns green after data is successfully sent.6.Once activated, the device uploads readings atscheduled times, if assigned to a tank in Pulse Level.•The device measures the tank liquid level.•Do not over tighten TLM into tank bung. Over tightening can cause permanent damage and result in inaccurate readings.•Do not use the TLM with pressurized tanks. Using the TLM in a pressurized tank will damage the TLM.•Do not use thread sealant or adhesive. Many of these products are chemically incompatible with the ABS plastic.F IG . 1Hot SpotLED lightInstallation3A8551C 3LED PatternBeep PatternTypical InstallationMount OptionsIdentify a threaded opening on the top of the tank for the device to be installed. The location should be vertical with a clear path to the contents of the tank. There should be no obstructions that could interfere with the signal. Insert the threaded device by screwing it into the opening. Do not over tighten.1.If the hole is not threaded, place the foam gasket(included with kit) over the opening.2.Place the mounting adapter (included with kit) ontop of the foam e the two (2) stainless steel self-tapping,counter-sunk screws (included with kit) to attach the adapter to the tank. Do not over tighten.4.Attach the device to the adapter. To form a secureseal, make sure that the device is vertical on the tank, that it is secured correctly to the base, and that the threads have not crossed.NOTE: If the tank does not contain a suitably positioned opening at the top of the tank, reference Drilling , page 4.LED PatternFunctionLED Test: when a magnet is held against the hot spot, the LED is briefly green, followed by briefly red, then the LED is off.Red LED Lit Modem Busy: registering on the network and sending data.Green LED LitActivated: the server has responded and activated the server.Beep PatternDefinition Low beep once persecond Network registration High beep once persecondTCP connecting Low beep once every four (4) secondsNetwork / TCP listen forcommandsLow beep once every two(2) seconds Re-establish network / TCPHigh /Low combinationbeepIncoming data Low / High combinationbeep Outgoing data Low double beep everyfour (4) secondsNetwork listen (data received and the device isactive)F IG . 2Installation43A8551CInstallation ExamplesDrillingIf the tank does not contain a suitable positioned opening at the top of the tank, it will be necessary to manually drill into the top of the tank.1.Select a flat area on the top of the tank locatedtowards the center (F IG . 3).2.Drill a 1.5 in. bsp hole at the selected area using a45.5 mm tapping drill.3.Continue with Activation .F IG . 3Operation3A8551C 5OperationView DataThe TLM is configurable with Pulse Level() to take readings at predefined times.After configuring the TLM using the Pulse Level, apply the magnet to the hot spot until a solid red lightappears, creating a connection between the TLM and the Pulse Level to load the configuration (F IG . 4).NOTE: Frequent measurements results in shorter battery life.Manual Measurement1.Hold the magnet (supplied) to the Hot Spot directlyunder the LED to activate the device (F IG . 1).2.Keep holding the magnet to the Hot Spot. The LEDwill flash green, and then flash red. Then the red light will stay lit.3.Remove the magnet.F IG . 4MagnetHot SpotF IG . 5Hot SpotLED lightRecycling and Disposal63A8551CRecycling and DisposalEnd of Product LifeAt the end of the product’s useful life, dismantle and recycle it in a responsible manner.•Remove batteries, circuit boards, LCDs (liquidcrystal displays), and other electronic components. Recycle according to applicable regulations. •Do not dispose of batteries or electroniccomponents with household or commercial waste.•Deliver remaining product to a recycling facility.Troubleshooting3A8551C 7TroubleshootingProblemCauseSolutionDevice is not reporting scheduled readings.Out of RF range.RF obstruction.Consider implementing a WiFi network and using Graco’s WiFi TLM.Ensure that the TLM is not encased in metal, since this would obstruct the signal.Weak or dead batteries.Replace batteries. See Replace Batteries , page 8.Tank Level Monitor was notassociated with a tank in software.Assign TLM serial number to tank.Reading is scheduled when pump is operating.Ensure readings are scheduled during times that the pump is not operating.LED will not turn on.Magnet removed too soon.Hold magnet to device hot spot for a longer period of time.Try using a stronger magnet.Weak or dead batteries.Replace batteries. See Replace Batteries , page 8.Service83A8551CServiceAfter the TLM has been installed, the only additional maintenance or service necessary is changing the batteries.Replace BatteriesNOTE: After battery placement, activate the TLM with a magnet (see Activation , page 2), to synchronize the TLM internal clock to maintain scheduled TLM readings.1.Remove the TLM from the tank by unscrewing itfrom the opening.2.Remove the four (4) screws that keep the casetogether (F IG . 6).3.Verify that the device is right side up beforeopening to prevent the batteries from falling out (F IG . 7).4.Replace the four (4) C-cell Alkaline batteries(F IG . 8).WARNINGFire and Explosion HazardSparking can occur when changing batteries. Only replace the batteries in a non-hazardous location away from flammable fluids and fumes.F IG . 6F IG . 7F IG . 8Bottom TopNegative (-)Positive (+)Service3A8551C 95.Make sure that the gasket is placed correctly (F IG .9).6.Reconnect the two halves, then replace the four (4)screws.7.Re-install the TLM back into the tank opening.8.Take a manual measurement to verify the TLM isactivated.F IG . 9GasketDimensions - Tank Specifications103A8551CDimensions - Tank SpecificationsVertical Tank:•Maximum Volume - 999,999 gallons or liters.•Tank walls must be uniformly vertical from empty level to full.Cylindrical Tank:•Maximum volume = 999,999 gallons or liters.•Tank end walls must be flat; they cannot be any other shape, including belled.Obround Tank:•Maximum volume = 999,999 gallons or liters.•Tank end walls must be flat; they cannot be any other shape, including belled.Non-Standard Tanks:•Maximum volume = 999,000 gallons or liters.•Define strapping table in Pulse Level software.•Up to 100 strapping table points to correlate tank fluid height to volume.F IG. 10F IG . 11F IG . 12WidthTechnical Specifications3A8551C 11Technical SpecificationsCalifornia Proposition 65Tank Level Monitor (TLM)US MetricCompatible Fluids oil, kerosene, diesel, lubricants, additives, DEF/AdBlue ®,coolants, water, waste oil, waste water, automatic transmission fluid (AFT), anti-freeze, and windshield washersolution Ultrasonic Tank Depth Measurement range 5.0 in. to 13 ft. 12 cm (minimum) to 400 cm Fluid Level Measurement Accuracy+/- 1.0 in.+/- 2.0 cmMounting 1.5 in and 2.0 in. threaded npt connectorClearance: Height above tank for TLM 7.5 in.19.1 cmWeight 1.17 lb. with batteries 530.7 g with batteriesRF Frequency Band LTE CAT-M1Operating Temperature Range 0°F to 122°F-17.8°C to 50°CStorage Temperature Range -22°F to 140°F -30°C to 60°CBatteries 4 x Alkaline C-cell Battery Life 5 years*Enclosure (Ingress Protection)IP67Tanks Maximum Volume 999,999 gallons 999,999 litersMaximum Height 13 ft.400 cmAltitude <6,000 ft.< 2 km*The battery life is based upon four (4) measurements per day and one (1) Cellular connection per day from a location where the cellular coverage does not require retries, and a normal distribution over the operating temperature range centered at +25°C (77°F).All trademarks or registered trademarks are the property of their respective owners.CALIFORNIA RESIDENTSWARNING: Cancer and reproductive harm – .All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.Original instructions. This manual contains English. MM 3A8551Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA Copyright 2021, Graco Inc. All Graco manufacturing locations are registered to ISO Revision C, December 2021 Graco Extended WarrantyGraco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twenty four months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco's written recommendations.This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco's sole obligation and buyer's sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.FOR GRACO CANADA CUSTOMERS The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.Graco Information For the latest information about Graco products, visit .For patent information, see /patents .TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590。
水浸传感器使用说明书
水浸传感器使用说明书文档版本：1. 产品介绍 (3)2. 产品选型 (4)3. 设备安装说明 (5)4. 配置软件安装及使用 (6)5. 通信协议 (7)6. 常见问题及解决办法 (9)7. 联系方式 (9)8. 文档历史 (10)9. 附录：各种壳体尺寸 (10)1. 产品介绍产品概述该水浸探测器广泛适用于通讯基站、宾馆、饭店、机房、图书馆、档案库、仓库、设备机柜以及其它需积水报警的场所，传感器内输入电源，感应线，信号输出三部分完全隔离。
安全可靠，外观美观，安装方便。
功能特点我公司采用交变电流采集积水的电感参数，准确区分是否发生水浸，甚至可以区分纯净水与自来水（默认以自来水为检测对象，若要检测纯净水请特殊说明）。
因为采用交变电流检测，电极即使长时间浸泡也不会产生电泳极化，不依赖特殊电极，做到寿命长、检测可靠。
---此技术为我公司专利，已获专利局授权，凡仿冒者我公司保留追究其法律责任的权利。
主要技术指标供电电源：10~30V DC 存储环境：-20℃~80℃ 误报率：<100ppm 继电器输出：常开触点系统框架图系统方案图2. 产品选型壁挂王字壳卡轨壳3. 设备安装说明设备安装前检查设备清单：■水浸传感器设备1台■合格证、保修卡、售后服务卡等■12V/2A防水电源1台（选配）■USB转485（选配）接线电源及485信号接线宽电压电源输入10~30V均可。
485信号线接线时注意A\B两条线不能接反，总线上多台设备间地址不能冲突。
继电器接口接线设备标配是具有1路继电器输出，两条出线为常开触点。
具体型号接线卡轨壳接线出485-B（蓝色）4. 配置软件安装及使用软件选择打开资料包，选择“调试软件”---“485参数配置软件”，找到打开即可。
参数设置①、选择正确的COM口（“我的电脑—属性—设备管理器—端口”里面查看COM端口），下图列举出几种不同的485转换器的驱动名称。
②、单独只接一台设备并上电，点击软件的测试波特率，软件会测试出当前设备的波特率以及地址，默认波特率为4800bit/s,默认地址为0x01。
水浸探测器安装与配置说明
水浸探测器安装与配置说明一、产品概述本产品应用电极浸水阻值变化的原理来进行积水探测，采用MCU智能检测方式，传感器防锈设计，有较高的精度与灵敏度，具有低功耗、良好的长期稳定性、可靠性等优点。
本产品可广泛用于地下室，水箱，机房，水路，水塔，水窖，水池，游泳池，水房，太阳能等一切储水设备及需要知道漏水或溢水的地方。
用户可根据需要选择独立型/联网型/无线型报警器。
二、主要技术参数产品名称水浸探测器产品型号工作电压DC3V电池产品类型无线型安装方式壁挂或台面安装工作温度0℃-+60℃环境湿度0%~80%RH产品尺寸89*89*28mm三、操作说明1、无线型水浸探测器产品请装入2节1.5V的AA电池,接入电池电压大于2.4V上电时,绿色LED闪烁一次,同时蜂鸣器鸣叫一声;若电压小于2.4V上电则黄色LED快速闪烁3次，同时蜂鸣器鸣叫3声，随后探测器即进入工状态。
2、当使用电池供电时绿色LED将每隔约25S闪烁一次，以示供电正常。
3、为确保探测器完好，使用时应定期长按HUSH/TEST键(>2S)进行测试,2S后LED会红、绿交替快速闪烁，同时蜂鸣器随LED点亮而鸣叫,直到按键松开;此外,测试时探测器会发出无线报警信号。
4、当传感器探测到水后，探测器红色LED将快速闪烁，同时蜂鸣器发出“滴、滴”报警声提示提醒用户有漏水或溢水现象；探测器，则会发出无线报警信号。
5、报警时用户可以可以长按或短按HUSH/TEST键进入静音，此时红色和绿色LED每隔1S交替点亮一次，蜂鸣器关闭，静音时间为10分钟,10分钟后探测器若仍探测到有水，则探测器继续报警提示用户有漏水或溢水现象。
6、正常状态也可短按HUSH/TEST键进入静音，此时绿色LED 每隔1S闪烁一次,遇水时红色和绿色LED每隔1S交替闪烁一次，而不输出其他信号：如声音、无线信号。
在静音状态可以拖地板或洗刷水池。
若想结束静音可以再次短按HUSH/TEST键。
WE-NBWS24P 智能水浸传感器 使用说明书
WE-NBWS24P智能水浸传感器使用说明书WE-NBWS24P智能水浸传感器采用光电技术，经微处理器运算处理，现场显示。
产品主体按IP65防护等级设计，传感器采用光电采集技术，有效解决因水浸导致漏电而烧坏设备的问题。
介质：水油等液体。
该无线水浸传感器广泛用于宾馆、图书馆、通讯基站、仓库、档案馆以及其它需要积水报警的扬所。
传感器由传感头、电池、MCU、射频模块、天线组成；外观小巧，安装方便。
一、特点：◆光电采集、安全隔离.◆电池供电，安装方便◆传输方式：NB-IOT二、技术参数：六、安装方法及要求1、安装：传感器主体有安装孔位，请垂直安装。
2、传感器：根据需要，传感器平行于地面放置，或根据检测高度垂直于地址安装；3、防止传感和腐蚀性或过热的介质接触：4、传感器采用锂电池供电，安装位置必须远离热源及高强度光源聚积点。
5、请保证天线各接口旋紧无松动，天线尽量远离墙壁，避免天线放置于金属管道中间。
如信号微弱，需适当延长天线致信号较强处。
天线远离变频器、电机等强干扰设备。
免责声明我司认为，在出版时尽量做到文档描述的准确无误。
考虑到产品的技术复杂性及工作环境的差异性，但仍难以排除个别不准确或不完备之描述，故本文档仅作用户参考之用。
我司保留在不通知用户的情况下对产品作出更改的权利，我公司不做任何法律意义上的承诺和担保。
鼓励客户对产品和支持工具最近的更新提出意见。
版权说明本文档所提及的元件及器件，皆为对其版权持有公司所公布的资料之引用，其修改和发布的权利均属于其版权持有公司，请在应用时通过适当的渠道确认资料的更新情况以及勘误信息，我司不对这些文档具有任何权利和义务。
智能水浸探测器使用说明书
比
技术参数
温馨提示
更长，探测器与传感器分体设计，能有效防 止高湿度环境对产品造成的影响。有较高的 精度与灵敏度，具有良好的长期稳定性、可 靠性等优点。本产品可广泛用于地下室，机 房，宾馆，水塔，水窖，水池，游泳池，太 阳能 , 厨房 , 卫生间等漏水、溢水或水位的探 测。
3.报警电流：≤30mA 4.联网方式：ZigBee自组网 5.无线组网距离：≤100米（空旷环境） 6.工作环境：- 10℃ ～ + 50℃； 7.环境湿度：最大95%RH 8.探测器尺寸：60 * 30* 12.5 mm 9.传感器尺寸：28.3 * 26 . 5 * 12 . 2mm
80cm
传装在容易泄漏水的区域。 2 、请勿将探测器安装在有雨水、有油 烟、水蒸气熏着的地方。 3 、请勿将探测器安装在水已经浸没的 地方。
*为了让您舒心使用，请仔细阅读操作指南
此指南图片仅供参考，请以实物为准
3 4
55mm
拔下电池绝缘片，使设备通电。
1 2
点击APP界面上的添加设备键，进入组网模式。
根据APP提示，长按设备组网键2秒后，绿灯快闪，APP界 面出现提示，绿灯长亮3秒,组网成功。(长按设备组网键5秒 可退网,绿灯慢闪3秒后,退网成功。)
撕下双面胶背膜，将设备贴在所需区域。
将探测器挂入安装底座。
5
制作要求： 1、制作尺寸：275 * 55mm 2、五折扇形折页折法，折叠后尺寸为55 * 55mm 3、120g铜版纸彩色印刷
55mm
55mm
55mm
55mm
55mm
智能水浸探测器 快速操作指南
本产品为智能水浸探测器 , 采用超低功耗 ZigBee 无线组网技术设计，电池使用寿命
FLIR 温湿度计和水分仪使用指南说明书
假使您要精确定位墙体后、地板下、或者天花板上的湿度问题，需要怎么做？ 对水分进行定位可以再简单不过。
FLIR 的精选温湿度计产品现已包含带内置热成像的选配项 — 我们称之为IGM™(红外成像引导测量技术)。
IGM 的设计目的是帮助您用最短的时间精确地找到需进一步测试和检查的位置。
利用IGM ，您能够防微杜渐，防患未然。
FLIR 很高兴为您带来一系列高品质的温湿度计产品，用以满足您的检测需求采用IGM™红外成像引导测量技术的温湿度计工作更快、更为智能，并快速进行下一工作。
张图像可现场更换的温度相对湿度传感器外部连接器，水份测量传感器热成像传感器采用由内置热成像传感器实现的IGM技术，MR176和MR160能够直观地帮助您准确找到水分可能存在的位置。
主要性能• 利用80 x 60 FLIR Lepton®热成像传感器对 水分进行精准定位• 利用内部或外部无探针式探头或外部探针式 探头进行有损或无损测量• 利用激光指示器和显示器十字线轻松对目标 进行定位• 利用免费FLIR Tools®软件查看图像并生成 报告MR176独一无二的性能• 测量温度和相对湿度(可现场更换的传感器能够自动 计算并显示环境读数)• 利用“锁定图像”设置防止极端温度对图像造成干扰• 在不利环境条件下获取准确读数(“不利环境稳定性 指示器”会告知您相对湿度读数是否已稳定)MR176/MR160带IGM™的温湿度计无探针式温湿度传感器微型USB连接器RJ45连接器感应式湿度传感器耐用性经2米跌落测试可现场更换的温度/相对湿度传感器红外温度计用于非接触式温度测量可存储读数并调取多达99个测量点蓝牙连接用于无线数据传输RJ45连接器MR77一台温湿度计包含了您在湿度调节或暖通 空调方面所需的一切：蓝牙®METERLiNK 功能、感应式湿度传感器和探针式探头、 温度和相对湿度传感器，以及IR 温度计带METERLiNK®的5合1温湿度计主要性能• 在移动设备上查看和分享读数• 利用可兼容的FLIR 红外摄像机将温湿度读数无线 整合至热影像中• 测量温度和相对湿度(可现场更换的传感器能够 自动计算并显示环境读数)• 可手动存储读数并调取多达20个测量点感应式水份测量传感器大数字显示和彩色条形图IP54防溅保护等级可保存多达10000个截图和读数耐用性经3米跌落测试外部连接器，用于探针式水份测量传感器微型USB 连接器RJ45 连接器MR60一款功能弃全的结构故障诊断工具，对多个现场温度数据随时间变化的情况进行采集和存储主要性能• 利用外部感应式或者探针式传感器进行无损或者 有损测量• 保存多达10000 查看的截图和读数• 利用含11种材料类别的内置数据库， 调节温湿度计• 利用免费FLIR Tools PC • 按需扩展您的水份测量仪 系列外部水份探针兼容水份含量测量仪可现场更换的电极探针IP40等级校准/探针检查，集成于盖帽内蓝牙连接用于无线数据传输耐用性经3米跌落测试利用含11种材料类别的内置数据库,根据测量材料调节水份测量仪高亮度LED 工作灯MR55利用无线连接和含11种材料类别的内置数据库对您的工作流程进行优化，以获得更加准确的读数主要性能• 将水份测量仪无线连接至“FLIR Tools Mobile”， 进而能够从您的移动设备上远程查看读数• 利用含11种材料类别的内置数据库将水份测量仪 调节为与测试材料相对应，包括木材、干墙和混 凝土等• 使用手机等移动终端扫描仪器背部的二维码 可访问与被测材料相对应的材料组别带蓝牙功能的探针式水份测量仪电容球传感器用于进行无损测量蓝牙连接用于无线数据传输背光显示屏IP40等级高亮度LED工作灯耐用性经2米跌落测试一款经济型蓝牙感应式水份测量仪，球头传感器，能够帮助您在短时间内实现大面积覆盖，不留痕迹主要性能• 利用球头传感器测量角落和踢脚线周围• 将温湿度计无线连接至从您的移动设备上查看实时读数• 通过创建受影响区域的热度图来对隐藏的水分源和 水分转移路径进行定位• 对位于表面以下至多题进行识别带蓝牙功能的球形探头水份测量仪MR59校准/探针检查，集成于盖内IP54防溅等级耐用性经3米跌落测试高亮度工作灯可更换式探针MR40一款便携式、耐用型温笔式水份测量仪/工作灯组合，设计用于查找和确认木材及一般建筑材料中的水份含量主要性能• 利用双探针、单量程笔式水份测量仪获取精确的 测量值• 轻松携带笔式水份测量仪并在狭窄的空间内进行 测量• 无需另外携带工作灯• 与热像仪配合使用以确认水份笔式水份测量仪 + 工作灯技术参数*取决于被测材料**对于类别9以外的材料，请下载“MR40材料转换表”(版本号MR40-AN01)：/app/account/fl_download_manuals利用FLIR配件对您的温湿度计进行升级MR01可现场更换的温度/相对湿度传感器设计用于与FLIR MR77或MR176配套使用，以获取精确的温度和湿度测量值。
LBV301振动水位传感器说明书
LBV301Vibrating level switch Rugged, flexible and cleanable P r o d u c t i n f o r m a t i o nf L u i d s e n s o r s | s i c K8014462/2011-09-05Subject to change without notice2Product descriptionThe LBV family of level sensors features a vibrating fork sensor that provides overfill or dry-run signals for containers with bulk or powdered materials. The reli -able and accurate LBV301 level sensors signal full, empty, or demand states. The rugged, stainless steel sensor design prevents bulk materials from jamming. When the probe is covered with bulk ma -terial, the changing vibration amplitude is reliably detected and converted into a switching signal. In addition, the LBV301 features an easy-to-clean monoprobethat is immune to contamination, making it suitable for use in the food industry. While the LBV311 base version is mainly mounted horizontally, the LBV321 with a suspension cable and the LBV331 with a tube extension are mounted vertically to bridge switching distances of up to 80 m or 6 m respectively. With a variety of process connections for hygienic applica -tions, and several output options, the LBV301 can be used for nearly all appli -cations, even in explosive atmospheres.at a glance•Compact sensor from 1 in threaded •Monoprobe design prevents bulk ma -terials from sticking and jamming •Polished monoprobe for food applica -tions•Commissioning without filling•Process temperature up to 250 °C•ATEX versions (1D/2D/1G/2G) avail -able•Tube-extended version (LBV331) up to 6 m and rope-extended version (LBV321) up to 80 m available for vertical mountingYour benefits•Easy commissioning and no calibra -tion reduce setup time•Maintenance-free sensor, reduces downtime•On-site testing – no mounting re-quired, which reduces setup time•Flexible and rugged system suitablefor many types of applications•Vertical mounting in difficult installa-tion conditionsf L u i d s e n s o r s|s i c K 8014462/2011-09-05Subject to change without notice 3detailed technical dataMechanics Electronicsf L u i d s e n s o r s | s i c K8014462/2011-09-05Subject to change without notice4type codesLBV311approval XX Without approvalcX ATEX II 1G, 1/2G, 2G Ex ia IIC T6cK ATEX II 1,1/2,2G Ex ia IIC T6+1,1/2,2D Ex tD IP66 T*LX ATEX II 1/2G, 2G EEx d IIC T6GX ATEX II 1,1/2,2D Ex tD IP66 T*eZATEX II 3G Ex nA II T5...T1 X Version / Process temperature a Standard / –50 °C ... +150 °C B With adapter / –50 °C ... +250 °CcDetection of solids in water / –50 °C ... +150 °C Process fitting / materialGc thread G 1 (din 3852-a) Pn 16 / 316 LGr thread G 1 (din 3852-a) Pn 16 / 316 L, ra<0,8µm nc Thread 1” NPT (ASME B1.20.1) PN16 /316Lnr Thread 1” NPT (ASME B1.20.1) PN16 /316L, Ra<0,8µm cV tri-clamp 2'' / 316L, ra<0,8µmef flange dn 50 Pn 40 form c, din2501 / 316L Kf flange dn 80 Pn 40 form c, din2501 / 316L Zf flange dn 100 Pn 6 form c, din2501 / 316L Ha Flange 2‘‘ 150lb RF, ANSI B16.5 / 316L oa Flange 3‘‘ 150lb RF, ANSI B16.5 / 316L sa Flange 4‘‘ 150lb RF, ANSI B16.5 / 316L au flange dn 50 10K rf Jis / 316L Bu flange dn 80 10K rf Jis / 316L cu flange dn 100 10K rf Jis / 316Lelectronicsc Contactless electronic switch 20...253 V AC/DC r Relay (DPDT) 20...72 V DC/20...253 V AC (3A)tTransistor (NPN/PNP) 10...55 V DC n namur signalHousing / enclosure rate K Plastic / IP66/ IP67a Aluminium / IP66/ IP68 (0.2 bar)V Stainless steel (precision casting) 316L / IP66, IP67 (IP68, 0.2 bar)8Stainless steel (electro buffed) 316L / IP66, IP67 (IP68, 0.2 bar)cable entry / cable gland m M20x1,5 / withn½“ nPt / withoutLBV311-Xf L u i d s e n s o r s | s i c K 8014462/2011-09-05Subject to change without notice5LBV321approvalXX Without approvalcX ATEX II 1G, 1/2G, 2G Ex ia IIC T6cK ATEX II 1,1/2,2G Ex ia IIC T6+1,1/2,2D Ex tD IP66 T*GX ATEX II 1,1/2,2D Ex tD IP66 T*eZ ATEX II 3G Ex nA II T5...T1 XVersion / Process temperature t cable PUR / –20 °C ... +80 °C H cable FEP / –40 °C ... +150 °CcDetection of solids in water / –20 °C ... +80 °C Process fitting / materialXP without / mono probe 316L, ra<0,8µm Gc thread G 1 (din 3852-a) Pn 6 / 316LGr thread G 1 (din 3852-a) Pn 6 / 316L, tuning stick ra<0,8µm nc Thread 1“ NPT (ASME B1.20.1) PN 6 / 316Lnr Thread 1“ NPT (ASME B1.20.1) PN 6 / 316L, tuning stick Ra<0,8µm efflange dn 50 Pn 40 form c, din2501 / 316L Kf flange dn 80 Pn 40 form c, din2501 / 316L Zf flange dn 100 Pn 6 form c, din2501 / 316L Ha Flange 2" 150lb RF, ANSI B16.5 / 316L 0a Flange 3" 150lb RF, ANSI B16.5 / 316L sa Flange 4“ 150lb RF, ANSI B16.5 / 316L au flange dn 50 10K rf, Jis / 316L Bu flange dn 80 10K rf, Jis / 316L cu flange dn 100 10K rf, Jis / 316Lelectronicsc Contactless electronic switch 20...253 V AC/DC r Relay (DPDT) 20...72 V DC/20...253 V AC (3A)tTransistor (NPN/PNP) 10...55 V DC n namur signalHousing / enclosure rate K Plastic / IP66/ IP67a Aluminium / IP66/ IP67 (IP68, 0.2 bar)V Stainless steel (precision casting) 316L / IP66, IP67 (IP68, 0.2 bar)8Stainless steel (electro buffed) 316L / IP66, IP67 (IP68, 0.2 bar)cable entry / cable gland m M 20x1,5 / with n½“ nPt / withoutLBV321-Xf L u i d s e n s o r s | s i c K8014462/2011-09-05Subject to change without notice6LBV331approvalXX Without approvalcX ATEX II 1G, 1/2G, 2G Ex ia IIC T6cK ATEX II 1,1/2,2G Ex ia IIC T6+1,1/2,2D Ex tD IP66 T*GX ATEX II 1,1/2,2D Ex tD IP66 T*eZ ATEX II 3G Ex nA II T5...T1 XVersion / Process temperature t Kabel PUR / –20 °C ... +80 °C H Kabel FEP / –40 °C ... +150 °CcDetection of solids in water / –20 °C ... +80 °C Process fitting / materialGc thread G 1 (din 3852-a) Pn 16 /316LGr thread G 1 (din 3852-a) Pn 16 / 316L, ra<0,8µm nc Thread 1“ NPT (ASME B1.20.1) PN 16 / 316Lnr Thread 1“ NPT (ASME B1.20.1) PN 16 / 316L, Ra<0,8µm cVtri-clamp 2" / 316L, ra<0,8µmef flange dn 50 Pn 40 form c, din2501 / 316L Kf flange dn 80 Pn 40 form c, din2501 / 316L Zf flange dn 100 Pn 6 form c, din2501 / 316L Ha Flange 2" 150lb RF, ANSI B16.5 / 316L 0a Flange 3“ 150lb RF, ANSI B16.5 / 316L sa Flange 4“ 150lb RF, ANSI B16.5 / 316L auflange dn 50 10K rf, Jis / 316L Bu flange dn 80 10K rf, Jis / 316L cu flange dn 100 10K rf, Jis / 316Lelectronicsc Contactless electronic swi 20...253 V AC/DC r Relay (DPDT) 20...72 V DC/20...253 V AC (3A)tTransistor (NPN/PNP) 10...55 V DC n namur signalHousing / enclosure rate K Plastic / IP66/ IP67a Aluminium / IP66/ IP67V Stainless steel (precision casting) 316L / IP66, IP67 (IP68, 0.2 bar)8Stainless steel (electro buffed) 316L / IP66, IP67 (IP68, 0.2 bar)cable entry / cable gland m M 20x1,5 / with n½“ nPt / withoutLBV331-Xf L u i d s e n s o r s|s i c K 8014462/2011-09-05Subject to change without notice 7ordering informationThe part numbers below show a selection of our common configurations and represent only an extract of the product portfolio. LBV311•Process connection: G 1 A•Process temperature: –50 °C ... +150 °C•Process pressure: –1 bar ... +16 bar•Housing material: Plastic•electrical connection: M20 x 1,5•Probe length:160 mmLBV321•Process connection: G 1 A•Process temperature: –20 °C ... +80 °C•Process pressure: –1 bar ... 6 bar•Housing material: Plastic•electrical connection: M20 x 1,5•Probe length:1.000 mmLBV331•Process connection: G 1 A•Process temperature: –50 °C ... +150 °C•Process pressure: –1 bar ... 16 bar•Housing material: Plastic•electrical connection: M20 x 1,5•Probe length:1.000 mmf L u i d s e n s o r s | s i c K8014462/2011-09-05Subject to change without notice8dimensional drawingsProcess connections LBV311G 1 AAll dimensions in mm (inch)G 1 ½ AAll dimensions in mm (inch)Tri-clampAll dimensions in mm (inch)Temperature adapter –50 °C ... +250 °CAll dimensions in mm (inch)f L u i d s e n s o r s|s i c K 8014462/2011-09-05Subject to change without notice 9Process connections LBV321G 1 AAll dimensions in mm (inch)G 1 ½ AAll dimensions in mm (inch)f L u i d s e n s o r s | s i c K8014462/2011-09-05Subject to change without notice10Process connections LBV331G 1 AAll dimensions in mm (inch)G 1 ½ AAll dimensions in mm (inch)FlangeAll dimensions in mm (inch)f L u i d s e n s o r s|s i c K 8014462/2011-09-05Subject to change without notice 11Wiring planrelay outputWe recommend connecting LBV301 in such a way that the switching circuit is open when there is a level signal, line break or failure (safe condition).The relays are always shown in non-operative condition.LBV301 - Wiring plan, single chamber housing1 Relay output2 Relay output3 Voltage supplytransistor outputWe recommend connecting LBV301 in such a way that the switching circuit is open when there is a level signal, line break or failure (safe condition).The instrument is used to control relays, contactors, magnet valves, warning lights, horns as well as PLC inputs.LBV301 - Wiring plan, single chamber housing1 Voltage supply LBV301 Transistor output NPN actionLBV301 Transistor output PNP actionnamur outputFor connection of the amplifier according to NAMUR (IEC 60947-5-6, EN 50227). You can find further information in the …Technical data“.LBV301 - Wiring plan, single chamber housingf L u i d s e n s o r s | s i c K8014462/2011-09-05Subject to change without notice12contactless electronic switchWe recommend connecting LBV301 in such a way that the switching circuit is open when there is a level signal, line break or failure (safe condition).The contactless electronic switch is always shown in non-oper-ative condition.The instrument is used for direct control of relays, contac -tors, magnet valves, warning lights, horns etc. It must not be operated without an intermediately connected load, because the electronics would be destroyed if connected directly to the mains.It is not suitable for connection to low voltage PLC inputs. Do -mestic current is temporarily lowered below 1mA after switch -ing off the load so that contactors, whose holding current is lower than the constant domestic current of the electronics, are reliably switched off.LBV301 - Wiring plan, single chamber housing1 Shieldingrecommended accessoriesLock fittingf L u i d s e n s o r s|s i c K 8014462/2011-09-05Subject to change without notice 13mounting instructionsswitching pointIn general, LBV301 can be installed in any position. The instru-ment only has to be mounted in such a way that the vibrating element is at the height of the desired switching point.The only exception is vertical mounting of the tuning fork from below. In this position there is the danger of solid particles get-ting stuck between the fork tines.socketThe vibrating element should protrude into the vessel to avoid build-up. For that reason, avoid using mounting bosses for flanges and screwed fittings. This applies particularly to horizon-tal installation and use with adhesive products.filling openingInstall the instrument in such a way that the vibrating ele-ment does not protrude directly into the filling stream. Should such an installation location be necessary, mount a suitable baffle above or in front of the vibrating element, e.g. L80 x8 DIN 1028 (see Fig. Part …a.“). In abrasive solids, mounting according to fig. Part …b.“ has proven to be a good solution. The mound that forms in the concave baffle protects it from abrasion.a. Convex mountingb. Concave mountinginflowing mediumIf LBV301 is mounted in the filling stream, unwanted false measurement signals can be generated. For this reason, mount LBV301 at a position in the vessel where no disturbances, e.g. from filling openings, agitators, etc., can occur.Horizontal mountingTo achieve a very precise switching point, you can installLBV301 horizontally. However, if the switching point can have a tolerance of a few centimeters, we recommend mounting LBV301 approx. 20° inclined to the vessel bottom to avoid build-up. Orient the tuning fork of LBV301 so that the product cannot remain lying on the fork surface. There is a mark on the thread hexagon for aligning the fork. Make sure that the mark points upward. material coneTo achieve a very precise switching point, you can install LBV301 horizontally. However, if the switching point can have a tolerance of a few centimeters, we recommend mounting LBV301 approx. 20° inclined to the vessel bottom to avoid build-up.Orient the tuning fork of LBV301 so that the product cannot remain lying on the fork surface. There is a mark on the thread hexagon for aligning the fork. Make sure that the mark points upward.To compensate measurement errors caused by the material cone in cylindrical vessels, the sensor must be mounted at a distance of d/6 from the vessel wall.1 LBV3212 Emptying opening3 Filling openingf L u i d s e n s o r s | s i c K8014462/2011-09-05Subject to change without notice14tensile loadWith cable version, make sure that the max. permissible tensile load on the suspension cable is not exceeded. The danger of this happening exists particularly with very heavy solids and large meas. lengths. The max. permissible load is stated in chapter …Technical data“.agitatorsDue to filling or extraction forces, vibrations or similar, the level switch can be subjected to strong lateral forces. For this reason, do not use an overly long extension tube for LBV331, but check if a LBV311 level switch couldn‘t be used instead, mounted on the side of the vessel in horizontal position. Extreme vibration caused by the process or the equIP ment, e.g. by fluidization or beaters in the vessel, can cause theextension tube of LBV301 to vibrate in resonance. This leads to increased stress on the upper weld joint. Should a longer tube version be necessary, you can provide a suitable support or guy directly above the vibrating element to secure the extension tube.This measure applies mainly to applications in Ex areas. Make sure that the tube is not subject to bending stress due to this measure.If an installation from above is necessary, check if you can use a cable version. Over a longer period of time, strong vibration can damage the instrument electronics. You can decouple the electronics from the process by using a remote (displaced) housing.Baffle protection against falling rocksIn applications such as grit chambers or settling basins for coarse sediments, the vibrating element must be protected against damage with a suitable baffle.t i t L e|s i c K 8014462/2011-09-05Subject to change without notice 15Search online quickly and safely with the SICK “Finders”Efficiency – with SICK e-commerce toolsfind out prices and availabilityDetermine the price and possible delivery date of yourdesired product simply and quickly.Request or view a quoteYou can have a quote generated online here.Every quote is confirmed to you via e-mail.order onlineYou can go through the ordering process in just a fewsteps.Product finder: We can help you to quickly target the pro-duct that best matches your application.applications finder: Select the application description onthe basis of the challenge posed, industrial sector, or pro-duct group.Literature finder: Go directly to the operating instructions,technical information, and other literature on all aspectsof SICK products.These and other Finders at ProductServiceclearly structured: You can findeverything you need for your sensorplanning under the menu items Pro-ducts, Information, and My Account.available 24 hours a day: Regard-less of where you are in the world orwhat you’d like to know – everythingis just a click away at www.mysick.com.safe: Your data is password-pro-tected and only visible to you. Withthe individual user management,you define who can see what dataand who can execute what actions.8014462/2011-09-05 ∙ G W (2011-09) ∙ W B U S m o d i n t 37SICK AG | Waldkirch | Germany | Leading technologiesWith a staff of more than 5,000 and over 50 subsidiaries and representa -tions worldwide, SICK is one of the leading and most successful manufac -turers of sensor technology. The power of innovation and solution competency have made SICK the global market leader. No matter what the project and industry may be, talking with an expert from SICK will provide you with an ideal basis for your plans – there is no need to settle for anything less than the best.Unique product range•Non-contact detecting, counting, classifying, positioning and measur -ing of any type of object or media •Accident and operator protection with sensors, safety software and services•Automatic identification with bar code and RFID readers•Laser measurement technology for detecting the volume, position and contour of people and objects•Complete system solutions for analy -sis and flow measurement of gases and liquidsComprehensive services•SICK LifeTime Services – for safety and productivity•Application centers in Europe, Asia and North America for the develop-ment of system solutions under real-world conditions•E-Business Partner Portal – price and availabi-lity of products, requests for quotation and online orderssicK at a glanceWorldwide presence with subsidiaries in the following countries:australiaBelgium/Luxembourg Brasilceská republikacanada china danmark deutschland españa franceGreat Britain india israel italia JapanMéxico nederland norge Österreich Polska românia russia schweizsingapore slovenija south africasouth Korea suomi sverige taiwan türkiyeunited arab emirates usaPlease find detailed addresses and additional representatives and agencies in all major industrial nations at 。
NSL-F连续水位传感器说明书
Technical specification at a glance· Extremely precise, fast & flexiblelevel sensor · Flex Hybrid Technology with digital + analog interface (IO-Link + 4...20 mA )· Modular design: configurable from the low-priced to the fully equipped high-end model · For vessels from 50 mm to 3 m height · CIP / SIP cleaning up to 143 °C / 120 min. · Response time < 100 msfor constantly precise values even with rapid level changes in high-speed fillers· Protection class IP 69K for safe application · Smart Replace Design : Easy replacement of all components by plug & playRemote-Version NSL-FROptional versionsCurved Version NSL-F-01Double rod NSL-F-02NEGELE MESSTECHNIK GMBH Raiffeisenweg 787743 Egg an der GuenzPhone +49 (0) 83 33 . 9204 - 0 Fax +49 (0) 83 33 . 9204 - 49 *************************Tech. Support***************************Phone +49 (0) 83 33 . 9204 - 72060013 / 1.1 / 2021-06-28 / MHModular Sensor platform with IO-Link and 4…20 mAThe Flex-Hybrid Technology with IO-Link and 4...20 mA combines the best of both worlds: Data from the sensor can be transmitted digitally, analogously or in parallel. The bidirectional communication enables status control and preventive maintenance at any time to avoid production downtimes. Installation and commissioning are time- and cost-saving thanks to plug-and-play technology, and sensor replacement is easier than ever before thanks to "Smart Replace Design" with automatic detection, configuration and parameterization.Note:Order code for optional versions see product information: Remote: NSL-FR Curved: NSL-F-01 Double rod:NSL-F-02。
PBLT2 可浸入水度传感器安装和运行说明说明书
ELECTRICAL INSTALLATIONAn external power supply delivering 13-30VDC with minimum current capability of 40mA DC (per transmitter)is required to power the control loop.See figure below for connection of the power supply,transmitter andThe maximum receiver load resistance (RLmax)for the DC power supply voltage (Vsup)is expressed by the formula:RLmax =Vsup –13V0.02AShielded cable is recommended for control loop wiring.The PBLT2Submersible Level Transducer is manufactured for years of trouble free service in the harshest applications.The PBLT2measures the height of liquid above its position in the tank referenced to atmospheric pressure.The transducer consists of a piezoresistive sensing element,encased in a 316SS housing.Perfect for wastewater and slurry applications with features to protect the unit from these demanding applications.Superior lightning and surge protection utilizing dual arrestor technology,grounded to case,eliminating both power supply surges and lightning ground strike transients (surge protection is not guaranteed and is not covered by warranty).Large diameter 316SS diaphragm seal is non-clogging and damage resistant to floating es equipped with a 270-pound tensile strength,shielded,vented cable.Ventilation tube in the cable automatically compensates for changes in atmospheric pressure above the tank.The vent tube has a filter attached to the end that will block particles,such as dust,dirt,and water droplets,from entering the tube.APPLICATIONS•Wastewater:sludge pits,clarifiers,digesters;Alum tanks;Chemical storage tanks;Oil tanks;Lime slurry;Sumps;Reservoirs.SPECIFICATIONSService:Compatible liquids.Wetted Materials:316SS,316L SS,epoxy adhesive;Cable:Polyether polyurethane or ETFE.Accuracy:±.25%full scale.Temperature Limits:0to 200ºF (-18to 93ºC).Compensated Temperature Range:0to 180ºF (-18to 82ºC).Thermal Effect:Less than ±.02%/ºF.Pressure Limit:2X full scale.Power Requirement:13to 30VDC.Output Signal:4to 20mA DC,two wire.Response Time:50msec.Loop Resistance:850ohms at 30VDC.Electrical Connection:Wire pigtail.Mounting Orientation:Suspended in tank below level being measured.Can be placed on the bottom of the tank on its side.Weight:4.3lb (2.0kg).Electrical Protection:Lightning and surge protection.Ø1/4x [Ø6.35x Example Construction RangeCable Length OptionsPBLT2PBLT220XXX 40XXXPU PBLT2-20-40Cage style submersible level transmitter,ETFE cableIn psi (5000psi maximum)In feet (1500feet maximum)Polyurethane cableModel Number Guide。
萤石 智能传感器 水浸传感器 CS-T10-A 使用说明书
快速操作添加到萤石设备请配合萤石网关（如A1C、R2、C1S和A2）和其他探测器（如门磁、被动红外探测器）使用。
传感器出厂时默认已安装好电池，无需重新安装。
方式一：通过二维码添加：1.2.登录“萤石云视频”手机客户端，从主菜单进入扫描界面。
扫描无线水浸传感器（以下简称“传感器”）背面的二维码，根据提示将探测器添加到萤石设备（需连接网络）上。
开启关联设备模式 1扫描二维码21的用户手册或者登录萤石官网查询。
方式二：通过注册信号添加：开启关联设备模式：A1、A1C和A2短按功能键即可；R2和R2S需要通过显示器登录萤石云账户，进入详情界面，选择“添加探测器”模式。
将传感器拿到距离至少一个固定探针1.2.开启关联设备模式 150cm以内2放置传感器1.调整最低报警水位（可选）：用手或螺丝刀调整可调节探针，可以调节最低报警水位。
注意事项：请将传感器放置在容易泄露水的区域；请不要将传感器放置在水已经浸没的地方;请不要将传感器放置在人来人往的区域、防止踢走遗失；请不要将传感器放置在具有腐蚀性或强磁场环境中；建议200平方以下面积内使用；如果房间面积过大，可以购买两个及两个以上的萤石设备配合使用。
. . . . . 2.选择位置：根据您的需要将传感器放置在选定的平面上（比如洗手间、阳台、厨房等）。
3.报警测试：选定放置区域后，将传感器放入水中测试。
此时传感器的蜂鸣器响15秒，同时关联的萤石设备收到报警信号，测试成功。
附录装箱清单T10-A X1用户指南打开产品包装后，请确认传感器是否完好，对照下图确认配件是否齐全。
传感器利用水的导电性原理，发生水患威胁时，传感器的蜂鸣器响起，同时关联的萤石设备收到一个报警消息。
功能介绍外观及功能介绍可调节探针水浸没可调节探针和至少一个固定探针时，传感器发出报警信号固定探针电池盖12更换电池电池型号为CR123A，续航能力为24个月。
当电池电量低时，传感器会发送一个低电量警告消息到萤石设备，提醒您及时更换电池。
系列水位传感器安全操作及保养规程
系列水位传感器安全操作及保养规程前言水位传感器是一种常见的传感器设备，广泛应用于工业、市政、农业等领域，起到监测水位、液位等参数的作用。
然而，由于使用不当、操作不规范等原因，水位传感器可能会出现故障、泄露等情况，给人身财产造成严重损失。
因此，为了保证水位传感器的安全运行，特制定本规程，以便广大用户进行参考。
一、水位传感器安全操作规程1.在使用水位传感器之前，应该对设备进行全面检查，确保设备没有损坏、泄漏等问题；2.了解水位传感器的安装、使用说明书，并严格按照说明书要求进行操作，特别是接线部分，应该按照说明书上的标注进行正确接线；3.安全操作过程中应该避免使用过度的力量，以免设备因受损伤而影响传感器的测量精度；4.避免操作时粗暴对待设备，避免拆卸、改装传感器，以免造成损坏；5.禁止直接使用手触碰传感器部分，传感器部分因温度过高或电压过大等因素导致受到伤害；6.对于发现设备故障现象，及时停止使用，避免继续使用时出现问题；7.禁止在水位传感器环境中吸烟、野外使用明火等操作，防止传感器损毁。
二、水位传感器日常保养规程1.定期对水位传感器进行全面检查，逐一检查传感器部分是否存在损坏、疲劳等问题；2.定期清理传感器的灰尘及污垢，以免影响传感器的测量精度；3.检查连接接线的紧固程度，确保安装固定牢固；4.定期对传感器进行测量校验，以确保传感器的测量精度；5.对传感器按照说明书要求保养，如更换过滤、填充物等；6.在使用年限已到或者已经损坏的情况下，应该及时更换，避免损坏扩大，给设备和人员带来伤害。
三、水位传感器事故处理方法1.发现传感器出现异常现象，立即停止使用，并对传感器进行全面检查，查找问题的根源；2.在确认问题后，进行相应的处理，如更换部件，重新校准传感器等，若是无法进行本地处理，则及时通知厂家进行处理；3.严禁对传感器进行拆卸、修理等操作，必要时，需寻找专业人员进行维修。
四、总结通过以上分析，我们可以看出，对于水位传感器来说，安全操作和日常保养保这一切才能有效地延长设备的使用寿命，避免设备的故障和事故。
传感器液体流量传感器安全操作及保养规程
传感器液体流量传感器安全操作及保养规程引言液体流量传感器是一种用于测量液体流动的装置，广泛应用于工业生产、农业灌溉、环境监测等领域。
为了确保传感器的正常运行和延长其使用寿命，本文详细介绍了传感器液体流量传感器的安全操作和保养规程。
安全操作规程1.在操作液体流量传感器之前，务必熟悉所使用传感器的技术参数和使用说明书，并在操作前进行必要的准备工作。
2.液体流量传感器需要与其他设备连接，如管道、控制系统等，在连接前请确保传感器与其他设备的兼容性和正确连接方式。
3.在安装液体流量传感器时，应确保传感器放置在垂直位置，并避免与其他物体碰撞，以防止传感器损坏。
4.在操作液体流量传感器时，应遵循操作规程，逐步进行各项操作，并注意传感器的读数、指示灯等参数的变化情况。
安全操作注意事项1.在操作液体流量传感器时，务必戴上适当的防护手套和眼镜，以防止液体的溅溢伤害。
2.在操作液体流量传感器时，应确保设备的电源以及液体流量的源头处于关闭状态，以免发生意外事故。
3.如需对传感器进行维护或更换零部件，应先关闭电源，并且必须由经过专业培训的人员进行操作，以确保安全性。
4.如果发现液体流量传感器存在任何异常情况，如漏液、故障等，请立即停止使用并联系专业人员进行维修。
保养规程1.定期清洁液体流量传感器以保持其正常工作状态。
使用软布蘸取清洁剂轻轻擦拭传感器表面，注意避免液体进入传感器内部。
2.液体流量传感器的电源线路需要定期检查，确保线路连接牢固，并避免因线路老化等原因引起的漏电、短路等安全问题。
3.定期检查液体流量传感器的读数准确性，并与其他可靠的流量测量仪器进行比对。
如有发现偏差较大的情况，应及时进行校准。
4.注意保持液体流量传感器的周围环境干燥，避免传感器受到潮湿、灰尘等不良环境影响，损坏传感器的正常工作。
总结本文介绍了传感器液体流量传感器的安全操作及保养规程，通过遵循这些规程可以确保传感器的正常工作，并延长其使用寿命。
在操作时要注意安全事项，定期保养维护，以确保传感器的准确性和可靠性。
Series SBLTX 浸水水位传感器规格-安装和操作说明书指南 L-37
Series SBLTX Submersible Level TransducerSpecifications - Installation and Operating InstructionsBulletin L-37The Series SBLTX Submersible Level Transducer is manufactured for years of trouble free service. The transducer consists of a piezoresistive sensing element, encased in a 316 SS housing. Bullet nose design protects diaphragm from damage. Comes equipped with a 270-pound tensile strength, shielded, vented cable. Ventilation tube in the cable automatically compensates for changes in atmospheric pressure above the tank.Intrinsic Safety Approval ClassificationThe SBLTX is UL listed for use in Hazardous (Classified) Locations. The protection method is by Intrinsic Safety, “ia”. It was investigated by UL under UL Standard 913 8th Edition, CAN/CSA C22.2 No. 60079-0:15 and CAN/CSA C22.2 No. 60079-11:14.Hazardous (Classified) Location Intrinsically Safe For:Class I, Div. 1, Groups A,B,C,D; Class II, Groups E,F,G; Class III Class I Zone 0 AEx ia IIC T4 Ga Zone 20 AEx ia IIIC T135°C Da Ex ia IIC T4 GaEx ia IIIC T135°C DaTa = -20°C to 80°C (ETFE Cable)Ta = -20°C to 65°C (Polyurethane Cable)Install in accordance with Control Drawing 001833-43. See Control Drawing 001833-43 for Entity Parameters.ATEX Certified for: II 1 G Ex ia IIC T4 Ga / II 1 D Ex ia IIIC T135°C Da (-20°C ≤ Tamb ≤ 80°C ETFE cable) (-20°C ≤ Tamb ≤ 65°C Polyurethane cable)ATEX EU-Type Certificate: DEMKO 18 ATEX 2080ATEX Standards: EN IEC 60079-0, EN 60079-11IECEx Certified for: Ex ia IIC T4 Ga / Ex ia IIIC T135°C Da (-20°C ≤ Tamb ≤ 80°C ETFE cable) (-20°C ≤ Tamb ≤ 65°C Polyurethane cable)IECEx Certificate of Conformity: IECEx UL 18.0086IECEx Standards: IEC 60079-0, IEC 60079-11UKCA Ex Certified for: Tamb ≤ 80°C ETFE cable) (-20°C ≤ Tamb ≤ 65°C Polyurethane cable)UKCA Ex Certificate: UL21UKEX2364UKCA Ex Standards: EN IEC 60079-0, EN 60079-11Install in accordance with Control Drawing 001833-46.See Control Drawing 001833-46 for Entity Parameters.Use with approved safety barriers using entity evaluation.INSTALLATION1. Location: Select a location where the temperature of the transducer will be between -4 and 176°F (-20 to 80°C) for ETFE cable or -4 and 149°F (-20 to 65°C) for polyurethane cable. Distance from the receiver is limited only by total loop resistance.2. Position: The transducer is not position sensitive. However all standard models are originally calibrated with the unit in a position with the pressure connection downward. Although they can be used at other an g les, for best accuracy it is recommended that units be installed in the position calibrated at the factory.3. Mounting: The transducer can be mounted via several methods. It can besuspended from the electrical cable, it can be placed resting on the bottom of the tank in either horizontal or vertical orientation, or it can be attached to a pipe orhang wire by the 1/2˝ NPT male connection on the top of the housing.4. Electrical ConnectionsWire Length: The maximum length of wire connecting the transducer and receiver is a function of wire size and receiver resistance. Wiring should not contribute more than 10% of the receiver resistance to total loop resistance. For extremely long runs (over 1000 feet), choose receivers with higher resistance to minimize the size and cost of connecting leads. Where wiring length is under 100 feet, wire as small as 22 AWG can be used.5. Wiring: An external power supply delivering 10-28 VDC with minimum current capability of 40 mA DC (per transducer) is required to power the control loop. See Figure A for connection of the power supply, transducer and receiver. The range of appropriate receiver load resistance (RL) for the DC power supply voltage availableis expressed by the formula:RL Max = Vps – 10 V 20 mA DCShielded cable is recommended for control loop wiring.Black wire is negative [-] and red wire is positive [+].Do not exceed specified supply voltage ratings. Permanent damage not covered by warranty will result. This device is notdesigned for 120 or 240 VAC operation. Use only on 10-28 VDC.MAINTENANCEAfter final installation of the pressure transducer and its companion receiver, no routine maintenance is required. A periodic check of system calibration is suggested. The Series SBLTX transducer are not field repairable and should be returned if repair is needed (field repair should not be attempted and may void warranty). Be sure to include a brief description of the problem plus any relevant application notes. Contact customer service to receive a return goods authorization number before shipping.POWER SUPPLY 10-28 VDC-RECEIVER BLACKREDPRESSURETRANSDUCERmA Figure AFigure B©Copyright 2022 Dwyer Instruments, LLCPrinted in U.S.A. 5/22FR# 443550-00 Rev. 10。
海尔湿度传感器说明书
Computer Interface: USB connection for set-up, cable includedPower: One 3.6V lithium 8.4 Ahcapacity (C cell) included (two included with wireless option) (replacement battery model no. BATT -C-3.6V)Battery Life (Typical): Up to 9 months Enclosure Material: 316 Stainless Steel and ABS center gasketEnclosure Finish: Brushed 316 stainless steelEnclosure Environmental Rating: Weatherproof, NEMA 4X (IP65)Sensor Wetted Parts: 316L stainless steelPressure Connection: ¼-18 NPT male Dimensions: D isplay: 115 D x 89 W x 74 H mm (4.5 x 3.5 x 2.9")S ensor: 72 to 89 mm L (2.8 to 3.5") below display, 80 mm (3.1") wideWeight: 1 kg (2.2 lb) Typical depending upon configurationFront Panel FunctionsBacklight: Manually turns backlight on/offMin/Max: Recalls minimum/ maximum valuesZero/Clear: Zeros display or clears minimum/maximumU W et/Wet Differential Pressure Measurement U 5-Point NIST Traceable Calibration Included U E asy to Read 25 mm (1") Backlit LCD Display U High 0.08% Accuracy U H i and Lo Alarms StandardU MIN/MAX/AVG Reading U U ser Selectable Analog Output 0 to 5 Vdc, 0 to 10 Vdc or 4 to 20 mA U W ireless Transmitter Option Sends Reading to Remote Location and Includes Charting and Data Logging Software U C E Certified U B attery Powered with Long Battery Life U N EMA 4X (IP65) EnclosureOmega’s DPG409 digital differential pressure gauge incorporates a rugged 316 SS enclosure designed forwashdown and marine applicationswith a precision 0.08% accuracypressure transducer and 316L SS wetted parts and body. The result is an extremely durable digital pressure gauge. Y ou get all the durability and stability of the micromachined silicon sensor in a rugged NEMA 4X (IP65) package.SPECIFICATIONSCE Compliant: MeetsEN61326-1: 2006 for industrial locations with analog output cables 30 m (98')Accuracy (Combined Linearity, Hysteresis and Repeatability): ±0.08% BSLStorage Temperature: -40 to 82°C (-40 to 180°F)Operating Temperature: -18 to 66°C (0 to 150°F)Thermal Effects (Over Operating Range): Zero Balance: R anges 10 inH 2O to 1 psi: ±1% span Ranges >1 psi: ±0.5% span Span Setting: R anges 10 inH 2O to 1 psi: ±1% span Ranges >1 psi: ±0.5% span Minimum Resistance Between Transducer Body and Any Wire: 100M Ω @ 50 VdcPressure Cycles: 1 million minLong Term Stability (1-Yr.): ±0.1% FS typicalAnalog Output: User selectable 0 to 5 Vdc, 0 to 10 Vdc or 4 to 20 mA(external 24 Vdc power supply required for all analog output types)Note: Analog output is independently scalableS et jumper to select current or voltage. Software selection of 0 to 5 Vdc, 0 to 10 Vdc, or 4 to 20 mAAnalog Output Cable: 2.7 m (9')Analog Output Accuracy: 0.08% typicalLine/Static Pressure: 500 psi maximum applied to both sides simultaneouly Proof Pressure (Differential):10 inH 2O = 10 times range 1 psi = 6 times range2.5 to 750 psi = 4 times range 1000 psi Range = 3 times range Hi-Side Containment Pressure (Differential):10 inH 2O to 5 psi: To 1000 psi 15 to 1000 psi: To 3000 psi Display: 4-digit LCD with userselectable backlighting, (9999 count) 25 mm (1') character height Sample/Display Rate: User selectable from 0.38 to 30 sec (preset to 1/sec)DPG409-050DWU shown smaller than actual size.Magnetic stylusincluded.F a s tD e l i v e r y –T y p i c a l l y St o c k t o2 W e e k s !Uni-Directional Ranges 0-10 inH 2O to 0-1000 psi(0-25 mb to 0-70 bar)StandardDPG409 Differential Pressure SeriesDIGITAL DIFFERENTIALPRESSURE GAUGE VERY HIGH ACCURACY316L SS WETTED PARTS AND BODYNote: Because of transmission frequency regulations, wireless models may only be used in the US, Canada and Europe.Comes complete with operator’s manual, one 3.6V lithium C cell battery (two with wireless option), set-up and configuration software(charting and databasing software with common drivers) USB cable, 2.7 m (9') analog output cable and 5-point NIST traceable calibration certificate.To order wireless option add suffix “-W” to model number for additional cost.Ordering Examples: DPG409-015DWU, 0 to 15 psi uni-directional differential pressure gauge with analog output.DPG409-100DWU-W, 0 to 100 psi uni-directional differential pressure gauge with analog output and wireless transmitter.Software Settings (via USB)(USB connection is for set-up only)Units: psi, inHg, inH 2O, bar, mbar, hPa units; must be specified at time of order Lock: Allows the lock-out of front panel functionsAlarms: User selectable “High” and “Low” alarm limits (open collector)Backlight: On/Off, 10 sec, 30 sec, 1 min, 5 minWireless Transmitter (Optional): Channel number, transmission rate, alarms, sensor offset, chart recording, data loggingCalibrate: Zero and spanOverrange Indication: “_ _ _ _”WIRELESS OPTIONTransmit Sample Rate: Userprogrammable from 1 sample/2 min to 1 sample/2 secRadio Frequency (RF)Transceiver Carrier: ISM 2.4 GHz RF Output: 10 dBm (10 mW)Range of RF Link: Up to 120 m (400') outdoors (line of sight); Up to 40 m (130') indoors/urbanIncluded Software: RequiresWindows ® 7 (32 bit); XP , VistaData Transmission to Host: Pressure reading, ambient temperature reading, RF transmit strength and battery levelWireless Receivers (For Use with “V2” for 0 to 10 Vdc, “TC”or “MA” for 4 to 20 mA.。
WD水感应传感器胶带安装和操作指南（Dwyer仪器公司）说明书
The small and discreet Model WD Water Detector is designed for dependabledetection of low levels of conductive liquids. The module features a sturdy and reli-able aluminum enclosure and is powered by 24 VAC or 24 to 30 VDC. Water sens-ing tape attaches to module and if any liquid comes in contact with the tape theresistance is changed and the alarm will be triggered. The tape is hydrophobic so itdoes not absorb any of the liquid it is detecting which makes for a faster drying timeand faster return to service after a water leak.The sensing tape is 1˝ wide and can be bought in lengths of 5, 10, 15 and 25 feet.Multiple tapes can be connected together to extend the coverage area which makesit ideal for domestic as well as commercial applications. Typical uses include com-puter rooms, telecommunication facilities, in drip pans under HVAC equipment andaround water pumps.INSTALLATIONRemove front panel of device. Run wires through back plate and make terminations.Reassemble front panel. Plug the tape into the module and fasten the mountingscrews. Use included plastic clips to mount tape to clean and dry surface. Contactcement provides a more secure installation than double face tape. Fold tape on it-self to make sharp corners. Insulate tape from conduits and ground wires. Ground-ed tape may cause detector failure.OPERATION AND TROUBLESHOOTINGGreen LED will indicate proper power. Red LED is an alarm indicator. The water de-tector will go to alarm contact state on loss of power or if the tape sensor is removed.An open or shorted tape will be sensed by the detector and will produce an alarmcontact state as well. The “Test” button can be used to test module operation. De-pressing the button will simulate water detection on the tape and produce an alarmcontact state. It is important to dry sensing cable with paper towel in case alarm hasbeen caused by water. Do not allow water to evaporate on its own. Conductiveresidue will be left behind which will change tape’s resistance. In worst case falsealarms may occur over time.If alarm is present and water cannot be located:1.Disconnect tape2.Unplug end of line (EOL) resistor from end of tape3.Plug EOL resistor into the moduleIf alarm clears then replace the tape.If alarm persists then replace the module.WIRINGModel WD Water Detector is provided with round opening for 1/2˝ conduit or flexconnector. Terminations are made to screw terminal connectors shown in Figure 1.Both outputs of alarm relay function identically. Contacts could be connected in par-*********************************************************************outputs.SPECIFICATIONSService: Conductive Liquid.Switch Type: DPDT.Electrical Rating: 1A @ 24 VAC/VDC.Power Requirements: 24 VAC, 24 to 30 VDC.Power Consumption: 35 mA maximum.Electrical Connections: Screw terminals.Conduit Connections: Hole for 1/2˝ conduit.Enclosure: Extruded aluminum.Sensor Tape: 1˝ (25.4 mm) wide and 5, 10, 15 or 25 feet long.Weight: 8 oz (.23 kg).CONNECTION[2.10]。
英雷水分仪简单操作说明书
简单操作指IMS-W8B-1红外水份仪简明操作方法一、怎样修改水份显示。
（即修改截距）（此项很重要）1、当发现仪器显示有较大偏差时，应及时用烘箱法与仪器显示值进行比对并加以修正（即修改水份显示值）。
2、烘箱法是校正水份仪的基准，只有通过现场取样做烘箱比对才能判断仪器显示准确与否。
每次取样时间最好在生产正常1小时以后，这时水份仪及生产控制系统均进入稳态。
取样应尽量在水份平稳时进行（水份波动最好上下不要超过0.2）。
取样点应在光斑位置后20-40公分处的物料表面。
3、校正一次水份仪，所取的样品不能太少，建议取样数量要≥5个。
在样品中去伪存真，找出统计规律后再加以修正。
采样数量越多，可靠性准确性就越高。
烘箱法用国标法：100度烘2小时。
天平的精度要求准确到1‰克，烘烤被测物料的器皿最好用铝盒（导热性要好）。
4、如何修改水份显示（即截距）举例：修改水份显示（即截距）方法如下：●在正常工作状态下按显示箱面板“设置”键，显示“-01-”（即当前通道号）。
●按显示箱面板“截距”键，这时会显示某一数值（即原来截距）。
●要求显示值增大，则按显示箱面板“增加”键；要求显示值减小，则按“减少”键。
增加或减少的数值就是仪器显示值和实际水份（烘箱值）的差值。
●按“确定”键予以确认，显示值面板显示“--16”。
●按“设置”键，水份仪显示修改后的水份值。
二、阻尼时间的含义。
阻尼可以理解为仪器对物料含水率的响应时间。
物料水份均匀度好，阻尼时间可以小些，如15秒；物料均匀度差，阻尼时间可以适当大些，如15-45秒。
阻尼的作用是可以滤去由于物料中微小团粒水份的突变而产生的尖脉冲。
阻尼时间小，反应灵敏，但数字显示跳动较大，视觉上也很不舒服；阻尼太大，反应会有些迟钝。
一般情况下15-35秒为好。
怎样修改阻尼时间：●在正常工作状态下按显示箱面板“设置”键，显示“-01-”（即当前通道号）。
●按显示箱面板“阻尼”键，这时会显示某一数值（即原来的阻尼时间）。
穿透式微波水分传感器使用说明书
SIED PAPER TECHNOLOGYL&W Scanpro Moisture Measuring Head DS-115 DS115穿透式微波水分传感器Manual使用说明书Contents目录1 General简介2 Mechanical Design机械设计3 Electrical Design电气设计4 Installation安装5 External Connectors and Controls外部连接和控制6 Operating Modes操作模式7 Processing the Output Signal输出过程信号8 Replacing the Measuring Head Window测量窗口的更换9 Technical Specification技术指标10 Spare Parts备品备件11 Graphs曲线图12 Drawings尺寸图1. General简介The Scanpro type DS 115, dual-sided, non-contacting measuring head is intended foron-line measurement of the moisture content in paper and paperboard.DS 115型双面不接触测量头是专门为在线测量一般纸和板纸水分设计的。
Its main application is after the drier section, but it may also be used at earlier process stages for correspondingly lighter paper grades .主要应用在干燥部以后，但也可根据相应低定量纸的情况用在比较前的位置。
The DS 115 supplies a standard DC output signal, mainly represent-ing the amount ofwater in the sheet.DS115提供标准的直流输出信号，主要代表纸张的水分值.For moisture percentage presen-tation, the signal has to be basis weight compensated,linearized and calibrated in the user‘s own processing unit.如果要代表水分的百分度，就要对信号进行定量补偿、线性化，用户在自己的处理单元中进行校正。
NBI 水质 ORP（氧化还原电位）传感器 用户手册说明书
NBI水质ORP（氧化还原电位）传感器用户手册深圳市农博创新科技有限公司使用前须知•使用前请仔细阅读本说明书，因不遵守本说明书的操作规程及注意事项而造成产品损坏或失效的，农博创新将视情况不提供保修服务。
•使用前请检查包装是否完好，若发现产品有损坏，请将损坏货品与包装物一并寄回农博创新。
•因产品功能、性能的持续改进和优化，如有参数变动，恕不另行通知。
1.概述1.1功能及应用介绍农博创新水质ORP（氧化还原电位）传感器是一款用于水质氧化还原电位监测的传感器，可准确测量微生物、鱼虾类、水草类等多种环境下淡水或海水水体的氧化还原性。
配合农博创1.2.2尺寸1.2.3各部位说明保护帽探头传感器接头2.使用方法2.1安装方式水质ORP传感器采用沉入式安装，详细的信息请参见Watcher Pro2(Aqua)无线水质监测产品用户手册。
3.维护3.1贮存水质ORP传感器使用完毕后需要长时间贮存时，应先将水质ORP传感器冲洗干净，然后插入加有 3.5mol/L氯化钾溶液的保护帽，或者可将水质ORP传感器浸没到氯化钾溶液（浓度4.注意事项1请勿将传感器置于水流较快的地方，会导致污染物堆积过快。
2请勿用硬物（手指，金属等）接触水质ORP传感器探头，否则会导致传感器探头表面产生划痕。
3定期清洗检查传感器探头，避免被污染。
6.联系我们深圳市农博创新科技有限公司地址：中国广东省深圳市南山区讯美科技广场2座7楼709官网：联系电话：400-015-1568邮箱：**********************保修条例1.本产品保修期为半年。
从发货之日起六个月内，本产品保修期内按说明书正常使用的状况下产生的故障，予以免费维修。
2.属于以下情况之一不属于免费保修范围，农博创新提供有偿服务，敬请留意：(1)超过保修有效期；(2)未按产品说明书的要求使用、安装而造成的损坏；(3)由非农博创新授权维修服务者拆修造成的损坏；(4)因用户使用不当而造成的产品损坏，如摔坏、机械破坏等；(5)因不可抗力（如火灾、地震、台风等）造成的损坏；(6)其他非产品本身设计、技术、制造、质量等问题而导致的故障或损坏。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
FBWINBLi智能水浸传感器
使
用
说
明
书
（V1.00）
使用产品前请阅读使用说明书
四川锦睿智诚科技有限公司
概要 (3)
一、特点： (3)
二、技术参数： (3)
三、安装方法及要求 (4)
免责声明 (4)
版权说明 (4)
FBWINBLi智能水浸传感器采用光电技术，经微处理器运算处理，现场显示。
产品主体按IP65防护等级设计，传感器采用光电采集技术，有效解决因水浸导致漏电而烧坏设备的问题。
介质：水油等液体。
该无线水浸传感器广泛用于宾馆、图书馆、通讯基站、仓库、档案馆以及其它需要积水报警的扬所。
传感器由传感头、电池、MCU、射频模块、天线组成；外观小巧，安装方便。
一、特点：
◆光电采集、安全隔离.
◆电池供电，安装方便
◆传输方式：NB-IOT
二、技术参数：
项目参数单位备注
过程介质液体
供电方式 3.6 V >8000mAh锂亚电池
检测方式折射式
通信方式NB-IOT
三、安装方法及要求
1、安装：
传感器主体有安装孔位，请垂直安装。
2、传感器：
根据需要，传感器平行于地面放置，或根据检测高度垂直于地址安装；
3、防止传感和腐蚀性或过热的介质接触：
4、传感器采用锂电池供电，安装位置必须远离热源及高强度光源聚积点。
5、请保证天线各接口旋紧无松动，天线尽量远离墙壁，避免天线放置于金属
管道中间。
如信号微弱，需适当延长天线致信号较强处。
天线远离变频器、电机等强干扰设备。
免责声明
我司认为，在出版时尽量做到文档描述的准确无误。
考虑到产品的技术复杂性及工作环境的差异性，但仍难以排除个别不准确或不完备之描述，故本文档仅作用户参考之用。
我司保留在不通知用户的情况下对产品作出更改的权利，我公司不做任何法律意义上的承诺和担保。
鼓励客户对产品和支持工具最近的更新提出意见。
版权说明
本文档所提及的元件及器件，皆为对其版权持有公司所公布的资料之引用，其修改和发布的权利均属于其版权持有公司，请在应用时通过适当的渠道确认资料的更新情况以及勘误信息，我司不对这些文档具有任何权利和义务。