H3CMSR930系统固件恢复

H3C MSR 930 系统恢复1 配置计算机IP 地址并关闭系统防火墙
将计算机的IP 地址更改为192.168.1.210/ 24 ，关闭系统防火墙。

2 安装配置 TFTP软件
安装 3com 的 tftp 软件，并安装下图位置进行配置。

将 H3C MSR 930路由器的系统固件放到TFTP服务器的指定目录。

3检查串口设备，并做相应的设置。

按照下图设置COM 接口。

4 启用 SecretCRT，选择串口连接
5线路连接
Consol 线连接电脑串口，电脑网线连接路由器的GE0 口（ WAN）
6以下是设备升级的具体操作
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Do you want to check SDRAM? [Y/N]
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing.........................Done!
****************************************************************************
** *H3C MSR930 BootWare, Version 5.10*
** ****************************************************************************
Copyright (c) 2004-2015 Hangzhou H3C Technologies Co., Ltd.
Compiled Date: Dec 21 2015
CPU Type: P1010
CPU L1 Cache: 32KB
CPU L2 Cache: 256KB
CPU Clock Speed: 533MHz
Memory Type: DDR3 SDRAM
Memory Size: 256MB
Memory Speed: 667MHz
BootWare Size: 1024KB
Flash Size: 128MB
CPLD Version: 1.0
PCB Version: 3.0
BootWare Validating...
Application program does not exist.
BootWare password: Not required. Please press Enter to continue.
Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>=========================== |<1> Boot System|
|<2> Enter Serial SubMenu|
|<3> Enter Ethernet SubMenu|
|<4> File Control|
|<5> Restore to Factory Default Configuration|
|<6> Skip Current System Configuration|
|<7>BootWare Operation Menu|
|<8> Clear Super Password|
|<9> Storage Device Operation|
|<0> Reboot|
============================================================================ Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 3 进入以太网子菜单
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash|
|<1> Download Application Program To SDRAM And Run|
|<2> Update Main Application File|
|<3> Update Backup Application File|
|<4> Update Secure Application File|
|<5> Modify Ethernet Parameter|
|<0> Exit To Main Menu|
|<Ensure The Parameter Be Modified Before Downloading!>|
============================================================================ Enter your choice(0-5): 5 修改以太网配置
==========================<ETHERNET PARAMETER SET>========================== |Note:'.' = Clear field.|
|'-' = Go to previous field.|
|Ctrl+D = Quit.|
============================================================================ Protocol (FTP or TFTP) :tftptftp 选择协议 tftp
Load File Name:MSR93X-CMW520-R2513P21.BIN
:MSR93X-CMW520-R2516P02.BIN系统文件的名称（和下
的文件名称一致）
Target File Name:MSR93X-CMW520-R2513P21.BIN
:MSR93X-CMW520-R2516P02.BIN保存到路由器的系统文件名称
Server IP Address:192.168.11.12 192.168.1.210 计算机的IP 地址
Local IP Address:192.168.11.13 192.168.1.1 路由器的IP 地址
Gateway IP Address:0.0.0.0 网关不用配置
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash|
|<1> Download Application Program To SDRAM And Run|
|<2> Update Main Application File|
|<3> Update Backup Application File|
|<4> Update Secure Application File|
|<5> Modify Ethernet Parameter|
|<0> Exit To Main Menu|
|<Ensure The Parameter Be Modified Before Downloading!>|
============================================================================ Enter your choice(0-5): 2 这里升级主程序文件Loading..................................................................... ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ......................................Done!
32574464 bytes downloaded!
Updating File flash:/MSR93X-CMW520-R2516P02.BIN............................. ............................................................................ ............................................................................ .....................................................................Done!
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash|
|<1> Download Application Program To SDRAM And Run|
|<2> Update Main Application File|
|<3> Update Backup Application File|
|<4> Update Secure Application File|
|<5> Modify Ethernet Parameter|
|<0> Exit To Main Menu|
|<Ensure The Parameter Be Modified Before Downloading!>|
============================================================================ Enter your choice(0-5): 0 这里升级完成，需要返回主菜单
===========================<EXTEND-BOOTWARE MENU>=========================== |<1> Boot System|
|<2> Enter Serial SubMenu|
|<3> Enter Ethernet SubMenu|
|<4> File Control|
|<5> Restore to Factory Default Configuration|
|<6> Skip Current System Configuration|
|<7>BootWare Operation Menu|
|<8> Clear Super Password|
|<9> Storage Device Operation|
|<0> Reboot|
============================================================================ Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 1 升级完成，重启设备
Starting to get the main application file--flash:/MSR93X-CMW520-R2516P02.
BIN!........................................................................ ............................................................................ ............................................................................ ........................
The main application file is self-decompressing............................. ............................................................................ ............................................................................ ............................................................................ ...........................................Done!
System application is starting................................................................................................................................................ ............................................................................................................................................................ ............................................................................................................................................................ .................................................................................................................................
Startup configuration file does not exist.
It will take a long time to get configuration file, please wait...
Retrieving configuration file failed!
User interface aux0 is available.
到目前为止，系统已经恢复完毕，并且新系统已经启动。

Press ENTER to get started.
<H3C>
#Jan 1 00:01:15:249 2012 H3C SHELL/4/LOGIN:
Trap 1.3.6.1.4.1.25506.2.2.1.1.3.0.1<hh3cLogIn>: login from Console
%Jan 1 00:01:15:249 2012 H3C SHELL/5/SHELL_LOGIN: Console logged in from aux0.
<H3C>
<H3C>system-view 进入系统视图
System View: return to User View with Ctrl+Z.
[H3C]display current-configuration查看系统当前配置信息
#
version 5.20, Release 2516P02 当前系统的版本信息
#
sysname H3C
#
domain default enable system
#
dns proxy enable
#
telnet server enable
#
dar p2p signature-file flash:/p2p_default.mtd
#
ndp enable
#
ntdp enable
#
cluster enable
#
port-security enable
#
password-recovery enable
#
vlan 1
#
domain system
access-limit disable
state active
idle-cut disable
self-service-url disable
#
dhcp server ip-pool vlan1 extended
networkip range 192.168.1.2 192.168.1.254
network mask 255.255.255.0
gateway-list 192.168.1.1
dns-list 192.168.1.1
#
user-group system
group-attribute allow-guest
#
local-user admin
password cipher $c$3$40gC1cxf/wIJNa1ufFPJsjKAof+QP5aV authorization-attribute level 3
service-type telnet
service-type web
#
cwmp
undocwmp enable
#
interface Aux0
async mode flow
link-protocolppp
#
interface Cellular0/ 0
async mode protocol
link-protocolppp
tcpmss 1024
#
interface NULL0
#
interface Vlan-interface1
ip address 192.168.1.1 255.255.255.0
tcpmss 1024
dhcp server apply ip-pool vlan1
#
interface GigabitEthernet0/ 0
port link-mode route
tcpmss 1024
#
interface GigabitEthernet0/1
port link-mode bridge
#
interface GigabitEthernet0/ 2
port link-mode bridge
#
interface GigabitEthernet0/ 3
port link-mode bridge
#
interface GigabitEthernet0/ 4
port link-mode bridge
#
dhcp enable
#
load xml-configuration
#
load tr069-configuration
#
user-interfacetty 12
user-interface aux 0
user-interfacevty 0 4
authentication-mode scheme
#
return
[H3C]【下载本文档，可以自由复制内容或自由编辑修改内容，更多精彩文章，期待你的好评和关注，我将一如既往为您服务】。