AEC_Q200低频发射天线系列

DATE
QTTY Reuslt SH TUV High Temperature Exposure (Storage)1000 hours (+125 ºC).
Measurement at 24+/-2 hours
after test conclusion
6 weeks MIL-STD-202 Method 108WUXI VDE High Temperature Exposure (Storage)1000 hours (+85 ºC).
Measurement at 24+/-2 hours
after test conclusion
6 weeks MIL-STD-202 Method 108SUZHOU UNNION High Temperature Exposure (Storage). Precualificacion.96 hours (+85 ºC).
Measurement at 24+/-2 hours
after test conclusion
0,6 week MIL-STD-202 Method 108SUZHOU UNNION Temperature Cycling 1000 cycles (-40 ºC to + 125 ºC)
Measurement at 24+/-2 hours
after test conclusion
10 weeks JESD22 Method JA-104WUXI VDE Temperature Cycling 1000 cycles (-40 ºC to + 85 ºC)
Measurement at 24+/-2 hours
after test conclusion
10 weeks JESD22 Method JA-104SUZHOU UNNION Moisture Resistance (25ºC to +65ºC) 30 ciclos,
8h/ciclo. Humidity HR:80%-
100%.. Measurement 24+/-2
hours after test conclusion
1,5 weeks MIL-STD- 202 Method 106SUZHOU UNNION Biased Humidity 1000 hours (+85 ºC, 85% RH).
Measurement at 24+/-2 hours
after test conclusion
6,5 weeks MIL-STD- 202 Method 103SUZHOU UNNION Operational Life 1000 hours (+105 ºC).
Measurement at 24+/-2 hours
after test conclusion
6,5 weeks MIL-PRF-27WUXI VDE External Visual See Method 2009. Inspect
device construction, marking
and workmanship. Electrical test
not required.
0,2 week MIL-STD-883 Method 2009WUXI VDE Physical Dimension See Method JB-100
0,2 week JESD22 Method JB-100SUZHOU UNNION Resistance to Solvents See Method 215. Note: Add
aqueois wash chemical. OKEM
Clean or equivalent. Do not use
banned solvents
0,2 week MIL-STD-202 Method 215SUZHOU UNNION Resistance to Salt See Method TSC7306G.
0,2 week See Valeo testing WUXI VDE Vibration 5g's for 20 minutes, 12 cycles
each of 3 orientations. Note: Use
8"X5" PCB, .031" thick, 7 secure
points one one long side and 2
secure points at corners of
opposite sides. Parts mounted
within 2" from any secure point.
Test from 10-2000 Hz.
1 week MIL-STD-20
2 Method 204WUXI VDE Resistance to Soldering Heat See Method 210. Condition B
No pre-heated of samples.
0,5 week MIL-STD-202 Method 210SUZHOU UNNION Thermal Shock (-40 ºC to +85ºC). Note:
Number of cycles required is
300. Maximum transfer time is
20 seconds. Dwell time is 15
minutes.
1,5 weeks MIL-STD-202 Method 107SUZHOU UNNION Thermal Shock (-40 ºC to +125ºC). Note:
Number of cycles required is
300. Maximum transfer time is
20 seconds. Dwell time is 15
minutes.
1,5 weeks MIL-STD-202 Method 107SUZHOU UNNION Thermal Shock (-40 ºC to +110ºC). Note:
Number of cycles required is
100. Maximum transfer time is
20 seconds. Dwell time is 20
minutes. Preheating y
Precooling -45 y 115ºC. 4 lotes
25 pcs cada uno.
1,5 weeks DIN EN 60068ESD See AEC-Q200-002
0,5 week AEC-Q200-002WUXI VDE Electrical Characterization
(-40 ºC, +25ºC,+125ºC)
1 week User Spec.
WUXI VDE Electrical Characterization
(-40 ºC, +25ºC,+85ºC)
1 week User Spec.NEWIC Drop test
Drop test, 1m, 3 falls, 3 axis
0,2week NEWIC
Connector terminal strength 98N, 1min
0,5 week NEWIC Terminal strength pin connecctor 100 in-out female connector 0,5 week NEWIC Screw tigthtening test
Tightening torque=30 N.mm or
more
0,5 week NEWIC Vertical strength test
Apply vertical Strenght to
destruction
0,5 week NEWIC Waterproof connectors submerger 0,15m in water
during , 30minutes 0,2 week
IP67 or above
Total Test conditions AEC-Q-200
Test Aditional requirements /
Reference PN
t Emitter Antenna。