热敏打印机使用说明书(英文)

热敏打印机使用说明书
Thermal Printer User Manual
一、打印机自检（LF键为指示灯）Printer self test(LF key is indicator light)
打印机在关机状态下，按住LF键不松手同时给打印机上电，松手，打印机会打印出自检条。

When the printer is power off,press LF key and meanwhile power on,release the key,the printer will print self test paper.
二、打印机设置（LF键为指示灯）Printer setting(LF key is indicator light)
打印机在关机状态下，按住LF键同时给打印机上电，停顿5秒后松手，打印机进入设置模式，并打印出设置报告，见
下（按键次数对应选择设置项前面序号）：
When the printer is power off,press LF key and meanwhile power on,release after 5 seconds,the printer will enter into
setting mode,and it will print out setting report,see below(the number of pressing key will be equal to the below according item number):
（1）退出设置模式exit setting mode
（2）恢复默认配置recover default setting
（3）设置打印机方向set printing direction
（4）选择字符点阵choose character dots
（5）选择打印机功耗choose printer power comsuption
（6）设置打印浓度set printing density
（7）设置串口波特率set serial baud rate
（8）设置串口效验位set serial parity
（9）选择HEX打印set HEX printing
（以下彩色字体部分均为打印机打印出的提示，后面黑色字体部分是我们加的操作说明）(The below colorful characters are prompts for printer print out,and the black characters are operation instruction which we added)
（1）退出设置模式（按1下LF键，走一小段空白行，退出设置模式）
exit setting mode(Press LF key one time,and the paper feed one line,it will exit
setting mode)
（2）恢复默认配置（连续按2下LF键，恢复默认设置）
recover default setting(Press LF key for 2 times,and it will recover default setting)
（1）返回上级设置（此时不想保存刚才设置，则按1下LF键回到设置主页）Return to last setting( If do not want to save the setting just now,then press LF
key for one time to return to setting homepage)
（2）确认恢复默认设置（连续按2下LF键，打印机打印出“恢复默认设置，系统复位”的字样提示）
Confirm recover default setting(Press LF key for 2 times,the printer will print
out the prompt"recovery default setting,system reset")
（3）设置打印机方向（连续按3下LF键，进入打印方向的设置，打印机打印出3个选项供设置）
Set printing direction(Press LF key for 3 times,it will enter into setting printing direction,the printer will print out 3 items for choose)
（1）返回上级设置（此时不想设置打印机方向，则按1下LF键回到设置主页）Return to last setting(If do not want to set printing direction now,then press LF
key for one time to return to setting homepage)
（2）从左到右打印（连续按2下LF键，打印机打印出下面3行字）
From left to right printing(Press LF key for 2 times,the printer will print out the
below 3 lines characters:)
从左到右打印From left to right printing
（1）返回上级设置（此时不保存该打印方向，可按1下LF键，返回上级设置）
Return to last setting(If do not want to save this printing direction,then
press LF key for one time,then it will to return to last setting)
（2）确认(若确认则连续按2下LF键回到设置主页，打印机方向设置成功) Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting printing direction successfully)
（3）从右到左打印（连续按3下LF键，打印机打印出下面3行字）
From right to left printing(Press LF key for 3 times,then the printer will print
out the below 3 lines characters:)
从右到左打印From right to left printing
（1）返回上级设置（此时不保存该打印方向，可按1下LF键，返回上级设置）
Return to last setting(If do not want to save this printing direction,then
press LF key for one time,then it will to return to last setting)
（2）确认(若确认则连续按2下LF键回到设置主页，打印机方向设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting printing direction successfully)
（4）选择字符点阵（连续按4下LF键，选择字符点阵，打印机会打印出3个选项供设置）
Choose character dots(Press LF key for 4 times,choose character dots,the printer will print out 3 items for choose)
（1）返回上级设置（此时不设置字符点阵，按1下LF键回到设置主页）Return to last setting(If do not want to set character dots now,then press LF key
for one time to return to setting homepage)
（2）选择8*16字符16*16汉字（连续按2下LF键，打印机打印出下面3行提示）Choose 8*16 character 16*16 chinese character(Press LF key for 2 times,the
printer will print out the below 3 lines prompts)
选择8*16字符16*16汉字Choose 8*16 character 16*16 chinese character
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,then press LF key for
one time,then it will to return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，字符点阵设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting character dots successfully)
（3）选择12*24字符24*24汉字（连续按3下LF键，打印机打印出下面3行提示）Choose 12*24 character 24*24 chinese character(Press LF key for 3 times,the
printer will print out the below 3 lines prompts)
选择12*24字符24*24汉字Choose 12*24 character 24*24 chinese character
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,then press LF key for
one time,then it will to return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，字符点阵设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting character dots successfully)
（5）选择打印机功耗（联系按5下LF键，选择打印机功耗，打印机会打印出6下面6个选项，请根据提示操作）
Choose printer power comsuption(Press LF key for 5 times,choose printer power comsuption,the printer will print out the bleow 6 items,please operate according to the below prompts)
（1）返回上级设置Return to last setting
（2）I级功耗（最低）（连续按2下LF键，打印机打印出下面3行字样）
I leverl power comption(the lowest) (Press LF key for 2 times,the printer will print
out the below 3 lines prompts)
I级功耗（最低）I leverl power comption
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,then press LF key for
one time,then it will to return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，打印机功耗设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting printer power comsuption successfully) （3）II级功耗（连续按3下LF键，打印机打印出下面3行字样）
II leverl power comption(Press LF key for 3 times,the printer will print out the
below 3 lines prompts)
II级功耗II leverl power comption
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,then press LF key for
one time,then it will to return to last setting)
（2）确定（若确认则连续按2次LF键回到设置主页，打印机功耗设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting printer power comsuption successfully) （4）III级功耗（连续按4下LF键，打印机打印出下面3行字样）
III leverl power comption(Press LF key for 4 times,the printer will print out the
below 3 lines prompts)
III级功耗III leverl power comption
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,then press LF key for
one time,then it will to return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，打印机功耗设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting printer power comsuption successfully) （5）IV级功耗（连续按5下LF键，打印机打印出下面3行字样）
IV leverl power comption(Press LF key for 5 times,the printer will print out the
below 3 lines prompts)
IV级功耗IV leverl power comption
（3）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,then press LF key for
one time,then it will to return to last setting)
（4）确认（若确认则连续按2次LF键回到设置主页，打印机功耗设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting printer power comsuption successfully) （6）V级功耗(最高)（连续按6下LF键，打印机打印出下面3行字样）
V leverl power comption(the highest) (Press LF key for 6 times,the printer will print
out the below 3 lines prompts)
V级功耗（最高）V leverl power comption(the highest)
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,then press LF key for
one time,then it will to return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，打印机功耗设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting printer power comsuption successfully)
（6）设置打印浓度（连续按6下LF键，开始设置打印浓度，打印机会打印出下面3个选项，请根据提示操作）
Set printing density(Press LF key for 6 times,set printing density,the printer will print out the bleow 3 items,please operate according to the below prompts)
（1）确认设置后返回（此时不设置浓度，按1下LF键回到设置主页）
Confirm setting and return back(If do not want to set print density now,press LF
key for one time to return to setting homepage)
（2）增量调整打印浓度（进入浓度设置后，连续按两2下LF键进行增量设置，打印机会打印出当前的浓度序号；若还需增加浓度，再连续按2下进行增量浓度
设置，直到设置到理想浓度，按1下LF键确认设置后返回到设置主页）
Increase the printing density( After entering the setting printing density mode,press
LF key for 2 times to increase the printing density,
the printer will print out the number for current printer density:If still want to
increase the density,press the LF key for 2 times again to increase
the printer density,and again to the density you want. Press LF key for 1 time to
confirm the setting and return back to setting homepage)
（3）减量调整打印浓度（进入浓度设置后，连续按两3下LF键进行减量设置，打印机会打印出当前的浓度序号；若还需增加浓度，再连续按3下进行减量浓
度设置，直到设置到理想浓度，按1下LF键确认设置后返回到设置主页）
Decrease the printing density( After entering the setting printing density
mode,press LF key for 3 times to decrease the printing density,
the printer will print out the number for current printer density:If still want to
decrease the density,press the LF key for 3 times again to decrease
the printer density,and again to the density you want. Press LF key for 1 time to
confirm the setting and return back to setting homepage)
（7）设置串口波特率（连续按7下LF键，开始设置串口波特率，打印机会有如下8个选项，请按需要选择）
Set serial baud rate(Press LF key for 7 times,set the serial baud rate,the printer will print out the below 8 items for choose)
（1）返回上级设置（此时不设置串口波特率，按1下LF键回到设置主页）Return to last setting(If do not want to set serial baud rate,press LF key for one
time to return back to homepage)
（2）1200bps（连续按2下LF键，打印机打印出下面字样）
1200bps(Press LF key for 2 times,the printer will print out the below prompts
选择1200bps Choose 1200bps
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,press LF key for one
time,then it will to return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，串口波特率设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting serial baud rate successfully)
（3）2400bps（连续按3下LF键，打印机打印出下面字样）
2400bps(press LF key for 3 times,the printer will print out the below prompts)
选择2400bps Choose 2400bps
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,press LF key for one
time,then it will return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，串口波特率设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting serial baud rate successfully)
（4）4800bps（连续按4下LF键，打印机打印出下面字样）
4800bps(press LF key for 4 times,the printer will print out the below prompts)
选择4800bps Choose 4800bps
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,press LF key for one
time,then it will return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，串口波特率设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting serial baud rate successfully)
（5）9600bps（连续按5下LF键，打印机打印出下面字样）
9600bps(press LF key for 5 times,the printer will print out the below prompts)
选择9600bps Choose 9600bps
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,press LF key for one
time,then it will return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，串口波特率设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting serial baud rate successfully)
（6）19200bps（连续按6下LF键，打印机打印出下面字样）
19200bps(press LF key for 6 times,the printer will print out the below prompts)
选择19200bps Choose 19200bps
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,press LF key for one
time,then it will return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，串口波特率设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting serial baud rate successfully)
（7）38400bps（连续按7下LF键，打印机打印出下面字样）
38400bps(press LF key for 7 times,the printer will print out the below prompts)
选择38400bps Choose 38400bps
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,press LF key for one
time,then it will return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，串口波特率设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting serial baud rate successfully)
（8）115200bps（连续按8下LF键，打印机打印出下面字样）
115200bps(press LF key for 8 times,the printer will print out the below prompts)
选择115200bps Choose 115200bps
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,press LF key for one
time,then it will return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，串口波特率设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting serial baud rate successfully)
（8）设置串口效验位（联系按8下LF键，打印出3个选项供设置）
Set serial Parity(press LF key for 8 times,the printer will print out the below 3 items for choose)
（1）返回上级设置（此时不设置串口效验位，按1下LF键回到设置主页）Return to last setting(If do not want to set serial parity,press LF key for one
time,then it will return to setting homepage)
（2）无效验（连续按2下LF键，打印机打印出下面字样）
No Parity(press LF key for 2 times,the printer will print out the below prompts)
选择无效验Choose No Parity
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,press LF key for one
time,then it will return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，效验位设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting serial parity successfully)
（3）有效验（连续按3下LF键，打印机打印出下面字样）
with Parity(press LF key for 3 times,the printer will print out the below prompts)
选择有效验Choose with Parity
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,press LF key for one
time,then it will return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，效验位设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting serial parity successfully)
（9）选择HEX打印（联系按9下LF键，打印出3个选项供设置）
Choose HEX printing(Press LF key for 9 times,then the printer will print out the below 3 items for choose)
（1）返回上级设置（此时不选择HEX打印，按1下LF键回到设置主页）Return to last setting(If do not want to choose HEX printing,press LF key for one
time,then it will return to setting homepage)
（2）正常打印（连续按2下LF键，打印机打印出下面字样）
Normal printing(press LF key for 2 times,the printer will print out the below
prompts)
选择正常打印Choose normal printing
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,press LF key for one
time,then it will return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，正常打印设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting normal printing successfully)
（3）选择HEX打印（连续按3下LF键，打印机打印出下面字样）Choose HEX printing( press LF key for 3 times,the printer will print out the below prompts)
选择HEX打印Choose HEX printing
（1）返回上级设置（此时不保存该设置，可按1下LF键，返回上级设置）Return to last setting(If do not want to save this setting,press LF key for
one time,then it will return to last setting)
（2）确认（若确认则连续按2次LF键回到设置主页，HEX打印设置成功）Confirm(If confirm,then press LF key for 2 times to return to setting
homepage,then setting HEX printing successfully)。