GGD配电柜出厂检验报告
GGD检验报告
按照国家GB50150-2006、BG50303-2002执行
品管部签字：
年月日
设计签字：
年月日
制造签字：
年月日
仓库接收签字：
年月日
电器柜出厂检验报告
年月日
用户名称
云南大理正大
合同编号
产品名称
配电柜
安装人员
梁朝仁于溁
设计人员
张生勃
数量
4
检验项目
检验内油污、灰尘等污垢，不得有裂纹、凹坑、划痕，保证柜体表面漆面完整、（颜色符合合同要求）。
2．一般
检查
检查导线与容量符合：
电器的布置、安装是否正确：
各元件固定牢固，无歪斜和破损现象：
金属框架接地或接零、接地标志、线是否正确明显：
机械操作元件是否有效：
3．一次
电器
元件
装配
电器保护和保护导体的截面积、柜间线路绝缘电阻值测试、柜（屏）、采用兆欧表进行对地检测、符合国家规定。
关键元器件要与认证产品安全件一览表相一致。包括断路器、刀开关、绝缘支撑件等产品的规格型号、厂家名称要符合合同技术要求。
母线搭接牢固，接触良好；相序标志正确、保护接地标志清楚；规格尺寸符合设计图纸要求。
4．二次
配线
配线合理、正确、走线整齐、固定牢靠、地线使用正确；二次元件安装牢固、接线正确。
控制线松动：
多股导线必须采用按装线鼻，通过插入式端子必须搪锡。连接导线要有合格证、型号与设计图纸相一致。
5．通电试验
通电操作，其动作应可靠、正常，符合设计要求。不应出现不动作或误动作。
配电柜和开关柜合格证
产品数量：1台
出厂编号：0905004
检验员：3
1.1-2005标准，产品合格，准予出厂。
耐斯电气有限公司
公司地址:市民营科技产业园区
合格证
产品名称：低压抽出式开关柜
规格型号：GCS
产品数量：1
出厂编号：0905007
检验员：3
出厂日期：2009年05月
本产品经检验符合GB7251.1-2005标准，产品合格，准予出厂。
耐斯电气有限公司
公司地址:市民营科技产业园区
合格证
产品名称：低压抽出式开关柜
规格型号：GCS
产品数量：1
出厂编号：0905008
检验员：3
出厂日期：2009年05月
本产品经检验符合GB7251.1-2005标准，产品合格，准予出厂。
检验员：3
出厂日期：2009年05月
本产品经检验符合GB7251.1-2005标准，产品合格，准予出厂。
耐斯电气有限公司
公司地址:市民营科技产业园区
合格证
产品名称：交流低压开关柜
规格型号：GCK
产品数量：1台
出厂编号：0905002
检验员：3
出厂日期：2009年05月
本产品经检验符合GB7251.1-2005标准，产品合格，准予出厂。
耐斯电气有限公司
公司地址:市民营科技产业园区
合格证
产品名称
规格型号
产品数量
出厂编号
检验员
出厂日期年月
本产品经检验符合GB7251.1-2005标准，产品合格，准予出厂。
耐斯电气有限公司
公司地址:市民营科技产业园区
合格证
产品名称
规格型号
产品数量
高压开关柜型式试验报告有效期
高压开关柜型式试验报告有效期：开关柜型式高压有效期试验型式检验报告有效期哪些需要型式试验报告型式试验报告几年有效篇一：高低压开关柜型式、试验执行标准高低压开关柜型式试验一、低压交流配电柜1、G GD型交流低压配电柜GGD型交流低压配电柜适用于变电站、发电厂、厂矿企业等电力用户的交流50Hz,额定工作电压380V，额定工作电流1000-3150A 的配电系统，作为动力、照明及发配电设备的电能转换、分配与控制之用。
产品具有分断能力高，动热稳定性好，电气方案灵活、组合方便，系列性，实用性强、结构新颖，防护等级高等特点。
缺点：回路少，单元之间不能任意组合且占地面积大，不能与计算机联。
目前作为普通工厂用低压成套开关设备中低档主流柜型。
执行IEC60439-《1 低压成套开关设备和控制设备》、GB7251.1-1997 《低压成套开关设备和控制设备》、GB/T14048.1-93 《低压开关设备和控制设备总则》等标准。
产品型号及含义2、GCK低压抽出式开关柜(GCK柜和GCS MNS柜抽屉推进机构不同) GCK低压抽出式开关柜(以下简称开关柜)由动力配电中心(PC) 柜和电动机控制中心(MCC)两部分组成。
该装置适用于交流50（60）HZ、额定工作电压小于等于660V、额定电流4000A及以下的控配电系统,作为动力配电、电动机控制及照明等配电设备。
具有分断能力高、动热稳定性好、结构先进合理、电气方案灵活、系列性、通用性强、各种方案单元任意组合、一台柜体，容纳的回路数较多、节省占地面积、防护等级高、安全可靠、维修方便等优点。
缺点：水平母线设在柜顶垂直母线没有阻燃型塑料功能板，不能与计算机联络。
执行IEC60439-《1 低压成套开关设备和控制设备》、GB7251.1-1997 《低压成套开关设备和控制设备》、GB/T14048.1-93 《低压开关设备和控制设备总则》等标准。
产品型号及含义GCK G是封闭式开关柜C是抽出式K是控制中心3、GCS型低压抽出式开关柜（GCS柜只能做单面操作柜，柜深800mm）GCS型低压抽出式开关柜使用于三相交流频率为50Hz，额定工作电压为400V（690V），额定电流为4000A及以下的发、供电系统中的作为动力、配电和电动机集中控制、电容补偿之用。
交流低压开关柜GGD例行检验报告
交流低压开关柜GGD例行检验报告
No：
产品名称：交流低压开关柜
型号规格：GGD-1000
依据标准：GB/T 7251.12-2013
出厂编号：2020101021
地下室低压配电柜
生产日期：2020年10月10日
序
项目
技 术 要 求
实测
试验结果
1
一般检查
柜体各功能单元门的开启角应大于90°，转动灵活
符合
对主电路和不与主电路直接连接的辅助电路之间、辅助电路与框架之间应能受50Hz，1890V历时7s耐压试验。
符合
9
保护措施和保护电路的连续性
有主接地点和接地标记，零部件和电器元件的保护接地使用专用的螺钉，以保证保护电路的连续性。
符合
电阻值应在100mΩ以下。
主开关安装支架-主接地
≤50MΩ
分支开关安装支架-主接地
≤50MΩ
接线端子支架-主接地
≤50MΩ
门锁-主接地
≤50MΩ
10
操作试验
手动操作试验：装置中所有手动操作部分：如主开关的操作手柄等手动操作5次而无异常现象出现。有连锁功能要求的应连锁可靠。
符合
11
一致性检查
1关键元器件和材料、2.结构 3.铭牌应与型式试验报告描述一致
符合
12
检验结论：该产品经我公司检验合格，准予出厂
符合
5
内部电路和连接
装应符合认证产品的一致性要求、工艺要求和图纸规定的要求。
符合
6
外接端子
数量、类型和标识应符合成套设备输出接线的要求及型式试验报告的要求
符合
7
绝缘电阻
相与相之间,相与地之间的绝缘电阻值绝缘电阻不应小于1000Ω/V，规定≥10MΩ。
电控柜出厂检验报告范本
1、如空气开关、交流接触器、热过载继电器、中间继电器、缺相保护器、PLC、变频器等，相关电气配件型号、品牌是否按照相关要求。
符合要求
4
相关控制线路
1、控制旋钮安装牢固、无松动；
2、电缆线、连接线横平竖直，整齐有序；
3、指示灯是否正常；
4、电缆线、连接线粗细、规格型号是否达到要求。
符合要求
检验结论
本产品质量检验结论：
本产品经检验合格，准予出厂。
检验：
检验日期：2018年09月20日
产品检验报告
产品名称
电控柜
数量
1套
规格型号
3J-0.6*0.8m
检验日期
2018/9/20
序号
项目
执行标准/要求
检测结果
1
外观要求
1、柜体类别为：室内柜或室外柜；
2、产品外表面不出现磕碰、变形、锈蚀;
3、相应的警示牌、标牌内容是否准确。
符合要求
2
规格尺寸
1、依据相关电气图纸检验电控柜柜体尺寸；
2、电控柜柜体材质：不锈钢柜、碳钢柜、烤漆柜；
GGD配电柜出厂检验报告
GGD型交流低压配电控制柜出厂检验报告型号：___________________一、目的通过检查和试验，对GGD型交流低压配电柜在技术条件，范围的性能、安全性、适应性及制造、安装工艺进行验证，使产品达到出厂要求。
二、主要依据1、LEC439-1-1992低压成套开关设备第一部分2、GB7251-1-1997低压成套开关设备和控制条一部分三、试验项目1、柜体检验2、装配检验3、断路器检验4、隔离刀开关检验5、主四路无载通电操作试验6、绝缘电阻测试7、介电强度试验8、结论GGD型交流低压配电柜出厂检验报告第2页（英文版）Two regulations promulgated for implementation is in the party in power for a long time and the rule of law conditions, the implementation of comprehensive strictly strategic plan, implementation in accordance with the rules and discipline to manage the party, strengthen inner-party supervision of major initiatives. The two regulations supporting each other, the < code > adhere to a positive advocate, focusing on morality is of Party members and Party leading cadres can see, enough to get a high standard; < rule > around the party discipline, disciplinary ruler requirements, listed as "negative list, focusing on vertical gauge, draw the party organizations and Party members do not touch the" bottom line ". Here, the main from four square face two party rules of interpretation: the first part introduces two party Revised regulations the necessity and the revision process; the second part is the interpretation of the two fundamental principles of the revision of laws and regulations in the party; the third part introduces two party regulations modified the main changes and needs to grasp several key problems; the fourth part on how to grasp the implementation of the two regulations of the party. < code > and < Regulations > revised the necessity and revisedhistory of the CPC Central Committee the amendment to the Chinese Communist Party members and leading cadres honest politics several guidelines > and < Chinese Communist Party discipline and Punishment Regulations > column 1 by 2015 to strengthen party laws and regulations focus. Two party regulations revision work lasted a Years, pooling the wisdom of the whole party, ideological consensus, draw historical experience, respect for the wisdom of our predecessors, which reflects the unity of inheritance and innovation; follow the correct direction, grasp the limited goals, adhere to the party's leadership, to solve the masses of the people reflect a focus on the problem. The new revision of the < code > and < rule >, reflects the party's 18 and the eighth session of the third, the spirit of the fourth plenary session, reflecting the experience of studying and implementing the General Secretary Xi Jinping series of important speech, reflects the party's eighteen years comprehensive strictly practice. (a) revised two regulations of the party need of < the ICAC guidelines > in < in 1997 Leaders as members of the Communist Party of China clean politics certain criteria (Trial) > based on revised, the promulgation and implementation of January 2010, to strengthen the construction of the contingent of leading cadres play animportant role. But with the party to manage the party strictly administering the deepening, has not been able to fully meet the actual needs. Content is too complicated, "eight prohibition, 52 are not allowed to" hard to remember, and also difficult to put into practice; the second is concisely positive advocated by the lack of prohibited provisions excessive, no autonomy requirements; the third is banned terms and discipline law, both with the party discipline, disciplinary regulations repeat and Criminal law and other laws and regulations repeat; the fourth is to "clean" the theme is not prominent, not for the existing problems, and is narrow, only needle of county-level leading cadres above. < rule > is in 1997 < Chinese Communist Party disciplinary cases (Trial) > based on revision, in December 2003 the promulgation and implementation, to strengthen the construction of the party play very important role. Along with the development of the situation, which many provisions have been unable to fully meet the comprehensive strictly administering the practice needs. One is Ji law, more than half of the provisions and criminal law and other countries laws and regulations Repetition; two is the political discipline regulations is not prominent, not specific, for violation of the party constitution, damage theauthority of Party Constitution of misconduct lack necessary and serious responsibility to pursue; third is the main discipline for the leading cadres, does not cover all Party members. Based on the above situation, need to < the criterion of a clean and honest administration > and < rule > the two is likely to be more relevant regulations first amendment. By revising, really put the authority of Party discipline, the seriousness in the party tree and call up the majority of Party members and cadres of the party constitution of party compasses party consciousness. (II) two party regulations revision process the Central Committee of the Communist Party of China attaches great importance to two regulations revision . Xi Jinping, general books recorded in the Fifth Plenary Session of the eighth session of the Central Commission for Discipline Inspection, on the revised regulations < > made clear instructions. According to the central deployment, the Central Commission for Discipline Inspection from 2014 under six months begin study two regulations revision. The Standing Committee of the Central Commission for Discipline Inspection 4 review revised. Comrade Wang Qishan 14 times held a special meeting to study two regulations revision, amendment clarifies the direction, major issues of principle, path and target,respectively held a forum will listen to part of the province (area) secretary of the Party committee, Secretary of the Discipline Inspection Commission, part of the central ministries and state organs DepartmentThe first party committee is mainly responsible for people, views of experts and scholars and grassroots party organizations and Party members. Approved by the Central Committee of the Communist Party of China, on 7 September 2015, the general office of the Central Committee of the Party issued a notice to solicit the provinces (autonomous regions, municipalities) Party, the central ministries and commissions, state ministries and commissions of the Party (party), the General Political Department of the military, every 3 people organization of Party of two regulations revision opinion. Central Commission for Discipline Inspection of extensive solicitation of opinions, careful study, attracting, formed a revised sent reviewers. In October 8 and October 12, Central Committee Political Bureau Standing Committee and the Political Bureau of the Central Committee After consideration of the two regulations revised draft. On October 18, the Central Committee of the Communist Party of China formally issued two regulations. Can say, two laws amendment concentrated thewisdom of the whole party, embodies the party. Second, < code > and < Regulations > revision of the basic principles of two party regulations revision work and implement the party's eighteen, ten eight plenary, the spirit of the Fourth Plenary Session of the Eleventh Central Committee and General Secretary Xi Jinping important instructions on the revised < low political criterion > and < Regulations >, highlighting the ruling party characteristics, serious discipline, the discipline quite in front of the law, based on the current, a long-term, advance as a whole, with Bu Xiuding independent < rule > and < rule >. Main principle is: first, adhere to the party constitution to follow. The constitution about discipline and self-discipline required specific, awaken the party constitution of party compasses party consciousness, maintaining the authority of the constitution. General Secretary Xi Jinping pointed out that "no rules, no side round. Party constitution is the fundamental law, the party must follow the general rules. In early 2015 held the eighth session of the Central Commission for Discipline Inspection Fifth Plenary Session of the 16th Central Committee, Xi Jinping again pointed out that constitution is the party must follow the general rules, but also the general rules." the revision of the< code > and < rule > is Method in adhere to the regulations established for the purpose of combining rule of virtue is to adhere to the party constitution as a fundamental to follow, the constitution authority set up, wake up the party constitution and party rules the sense of discipline, the party constitution about discipline and self-discipline specific requirements. 4 second is to adhere to in accordance with the regulations governing the party and the party. The Party of rule of virtue "de", mainly refers to the party's ideals and beliefs, excellent traditional style. The revised the < code > closely linked to the "self-discipline", insisting on the positive initiative, for all members, highlight the "vital few", emphasized self-discipline, focusing on the morality, and the majority of Party members and the ideological and moral standards. The revised < > Ji method separately, Ji, Ji Yan to Method, as a "negative list", emphasizing the heteronomy, focusing on vertical gauge. Is this one high and one low, a positive reaction, the strict party discipline and practice results transformation for the integration of the whole party to observe moral and discipline requirements, for the majority of Party members and cadres provides benchmarking and ruler. Third, insist on to. In view of the problems existing in theparty at the present stage, the main problems of Party members and cadres in the aspect of self-discipline and abide by the discipline to make clearly defined, especially the party's eighteen years strict political discipline and political rules, organization and discipline and to implement the central eight provisions of the spirit against the four winds and other requirements into Disciplinary provisions. Not one pace reachs the designated position, focusing on in line with reality, pragmatic and effective. After the revision of major changes, major changes in the < code > and < rule > modified and needs to grasp several key problems (a) < code > < code > adhere to according to regulations governing the party and party with morals in combination, for at the present stage, the leadership of the party members and cadres and Party members in existing main problems of self-discipline, put forward principles, requirements and specifications, showing Communists noble moral pursuit, reflected at all times and in all over the world ethics from high from low 5 common requirements. One is closely linked to the "self-discipline", removal and no direct relation to the provisions of . the second is adhere to a positive advocate, "eight prohibition" 52 are not allowed to "about the content of the" negative list moved into synchronizationamendment < cases >. Three is for all the party members, will apply object from the leadership of the party members and cadres to expand to all Party members, fully embodies the comprehensive strictly required. The fourth is prominent key minority, seize the leadership of the party members and cadres is the key, and put forward higher requirements than the ordinary Party members. Five is to simplify, and strive to achieve concise, easy to understand, easy to remember. The revised < code > is the ruling Party since the first insists on a positive advocate forAll Party members and the self-discipline norms, moral declaration issued to all members of the party and the National People's solemn commitment. > < criterion of a clean and honest administration consists of 4 parts, 18, more than 3600 words. After the revision of the < code >, a total of eight, 281 words, including lead, specification and Party member cadre clean fingered self-discipline norms, etc. Part 3 members low-cost clean and self-discipline, the main contents can be summarized as "four must" "eight code". Lead part, reiterated on ideal and faith, fundamental purpose, the fine traditions and work style, noble sentiments, such as "four must" the principle of requirements, strong tone of self-discipline, The higher request for 6 andsupervised tenet, the foothold in permanent Bao the party's advanced nature and purity, to reflect the revised standards requirements. Members of self-discipline norms around the party members how to correctly treat and deal with the "public and private", "cheap and rot" thrifty and extravagance "bitter music", put forward the "four norms". Party leader cadre clean fingered self-discipline norms for the leadership of the party members and cadres of the "vital few", around the "clean politics", from civil servant of the color, the exercise of power, moral integrity, a good family tradition and other aspects of the leadership of the party members and cadres of the "four norms" < > < norm norm. "The Party member's self-discipline norms" and "party members and leading cadre clean fingered self-discipline norms," a total of eight, collectively referred to as the "eight". "Four must" and "eight" of the content from the party constitution and Party's several generation of leaders, especially Xi Jinping, general secretary of the important discussion, refer to the "three discipline and eight points for attention" statements, and reference some embody the Chinese nation excellent traditional culture essence of epigrams. (2) the revised regulations, the main changes in the revised Regulations > to fully adapt to thestrictly requirements, reflects the according to the regulations governing the law of recognition of deepening, the realization of the discipline construction and Jin Ju. < rule > is party a ruler, members of the basic line and follow. And the majority of Party members and cadres of Party organizations at all levels should adhere to the bottom line of thinking, fear discipline, hold the bottom line, as a preventive measure, to keep the party's advanced nature and purity. 1, respect for the constitution, refinement and discipline. Revised < rule > from comprehensive comb physical constitution began, the party constitution and other regulations of the Party of Party organizations and Party discipline requirements refinement, clearly defined in violation of the party constitution will be in accordance with regulations to give the corresponding disciplinary action. The original 10 categories of misconduct, integration specification for political discipline, discipline, honesty and discipline masses Ji Law and discipline and discipline and other six categories, the content of < rule > real return to Party discipline, for the majority of Party members and listed a "negative list. 7 2, highlighting the political discipline and political rules. > < Regulations according to the stage of the discipline of outstandingperformance, emphasizing political discipline and political rules, organization and discipline, in opposition to the party's leadership and the party's basic theory, basic line, basic program and basic experience, the basic requirement of behavior made prescribed punishment, increase the cliques, against the organization such as violation of the provisions, to ensure that the central government decrees and the Party of centralized and unified. 3, adhere to strict discipline in the law and discipline In front, Ji separated. Revised < Regulations > adhere to the problem oriented, do Ji separated. Any national law existing content, will not repeat the provisions, the total removal of 79 and criminal law, repeat the content of the public security management punishment law, and other laws and regulations. In the general reiterated that party organizations and Party members must conscientiously accept the party's discipline, die van comply with national laws and regulations; at the same time, to investigate violations of Party members and even criminal behavior of Party discipline and responsibility, > < Regulations distinguish five different conditions, with special provisions were made provisions, so as to realize the connection of Party discipline and state law. 4, reflect Wind building and anti-corruptionstruggle of the latest achievements. < rule > the party's eighteen years implement the spirit of the central provisions of the eight, against the requirements of the "four winds" and transformation for disciplinary provisions, reflecting the style construction is always on the road, not a gust of wind. In the fight against corruption out of new problems, increase the trading rights, the use of authority relatives profit and other disciplinary terms. Prominent discipline of the masses, the new against the interests of the masses and ignore the demands of the masses and other disciplinary terms and make provisions of the disposition and the destruction of the party's close ties with the masses.Discipline to protect the party's purpose. 8 of these regulations, a total of three series, Chapter 15, 178, more than 24000 words, after the revision of the regulations a total of 3 series, Chapter 11, 133, 17000 words, divided into "general" and "special provisions" and "Supplementary Provisions" Part 3. Among them, add, delete, modify the provisions of the proportion of up to nearly 90%. 1, the general general is divided into five chapters. The first chapter to the regulations of the guiding ideology, principles and scope of application of the provisions, highlight the strengthening ofthe party constitution consciousness, maintenance the authority of Party Constitution, increase the party organizations and Party members must abide by the party constitution, Yan Centralized centralized, would examine at all levels of the amended provisions implementing and maintaining Party discipline, and consciously accept the party discipline, exemplary compliance with national laws and regulations. The second chapter of discipline concept, disciplinary action types and effects of the regulations, will be a serious warning from the original a year for a year and a half; increase the Party Congress representative, by leaving the party above (including leave probation) punishment, the party organization should be terminated its representative qualification provisions. The third chapter of the disciplinary rules of use prescribed in the discipline rectifying process, non convergence, not close hand classified as severely or heavier punishment. "Discipline straighten "At least eighteen years of five years, these five years is to pay close attention to the provisions of the central eight implementation and anti -" four winds ". The fourth chapter on suspicion of illegal party disciplinary distinguish five different conditions, with special provisions were madeprovisions, to achieve effective convergence of Party and country 9 method. < rule > the provisions of Article 27, Party organizations in the disciplinary review found that party members have committed embezzlement, bribery, dereliction of duty dereliction of duty and other criminal law act is suspected of committing a crime shall give cancel party posts, probation or expelled from the party. The second is < Regulations > Article 28 the provisions of Party organizations in the disciplinary review But found that party members are stipulated in the criminal law, although not involved in a crime shall be investigated for Party discipline and responsibility should be depending on the specific circumstances shall be given a warning until expelled punishment. This situation and a difference is that the former regulation behavior has been suspected of a crime, the feeling is quite strict, and the latter for the behavior not involving crime, only the objective performance of the provisions of the criminal code of behavior, but the plot is a crime to slightly. < Regulations > the 29 provisions, Party organizations in the discipline review found that party members and other illegal behavior, affect the party's image, the damage to the party, the state and the people's interests, we should depend on the situationSeriousness given disciplinary action. The loss of Party members, seriously damaging the party's image of behavior, should be given expelled from the party. At this article is party member is in violation of the criminal law outside the other illegal acts, such as violates the public security administration punishment law, customs law, financial laws and regulations behavior. The fourth is < cases > Article 32 stipulates, minor party members and the circumstances of the crime, the people's Procuratorate shall make a decision not to initiate a prosecution, or the people's court shall make a conviction and exempted from criminal punishment shall be given within the party is removed from his post, probation or expelled from the party. Party members and crime, sheets were fined in accordance with For acts; the principal Ordinance amended the provisions of the preceding paragraph. This is the new content, in order to achieve Ji method effective convergence. Five is < > the thirty third article 10 of the provisions, the Party member due to an intentional crime is sentenced to criminal law (including probation) sheets or additional deprivation of political rights; due to negligence crime and was sentenced to three years or more (excluding three years) a penalty, shall give expelled punishment. Due to negligence crime is convictedand sentenced to three years (including three years) in prison or be sentenced to public surveillance, detention, shall in general be expelled from the party. For the individual may not be expelled from the party, should control Approval. This is followed and retained the original > < Regulations the provisions of punishment party authorization rules and report to a level party organizations. For is "party members with criminal acts, and by the criminal punishment, generally should be expelled from the party". The fifth chapter of probationary Party member of the discipline and discipline after missing members of the treatment and punishment decisions, such as the implementation of the provisions, clear the related party discipline and punishment decision made after, for duties, wages and other relevant alteration formalities for the longest time. 2, sub sub section will the original regulations of10 categories of acts of violation of discipline integration revised into 6 categories, respectively, in violation of the punishments for acts of political discipline "in violation of discipline behavior of punishment" in violation of integrity of disciplinary action points "of violation punishments for acts of mass discipline" "the violation of work discipline, punishment" in violation of discipline of life behaviorpunishment "6 chapters. 3, annex" Supplementary Provisions "clear authority making supplementary provisions of, cases of interpretative organ, as well as regulations implementation time and retroactivity etc.. 11 (3) learning understanding > < regulations needs to grasp several key problems The first problem -- about the violation of political discipline behavior > < new ordinance chapter 6 the political discipline column for the six disciplines, that is the main opposition to Party leadership and the opposition of the basic theory, basic line, basic program and basic experience, basic requirements of misconduct made provisions of the disposition, especially the eighteen since the CPC Central Committee put forward the Yan Mingzheng treatment of discipline and political rules requirements and practical achievements transformation for Discipline article, increase the false debate central policies, cliques, against the organization review, make no discipline of the principle of harmony terms. These are the party's eighteen years in comprehensive strictly Process combined with the practice of rich content. (1) false debate the central policies and undermine the Party of centralized and unified the problem is made in accordance with the provisions of the party constitution. Constitution in general programme requirementsadhere to democratic centralism is one of the requirements of the construction of the party must adhere to the four cardinal. Application of this principle is not only the party the basic organization principle and is also the mass line in party life, it requires that we must fully develop inner-party democracy, respect for the dominant position of Party members, safeguarding the Party member democratic rights, give full play to the enthusiasm and creativity of the party organizations at all levels and Party members, at the same time, also must implement the right concentration, ensure the party's mission < the chaos in unity and concerted action to ensure that the party's decision to get quickly and effectively implementing. The Party Central Committee formulated the major principles and policies, through different channels and ways, fully listen to the party organizations and Party members of the opinions and suggestions, but 12 is some people face to face not to say back blather "" will not say, after the meeting said, "" Taiwan does not say, and nonsense ", in fact, not only disrupt the people thought, some causing serious consequences, the damage to the Party of the centralized and unified, hinder the central policy implementation, but also a serious violation of the democratic system of principles. There is no doubt that shall, inaccordance with the Regulations > 4 Specified in Article 6 to give the appropriate punishment. For did not cause serious consequences, to give criticism and education or the corresponding tissue processing. (2) about the destruction of the party's unity < New Regulations > the forty eighth to fifty second article, to damage Party's unity unified and violation of political discipline, punishment situation made explicit provisions. Article 52 of the new "in the party get round group, gangs seek private gain, cliques, cultivate private forces or through the exchange of interests, for their own to create momentum and other activities to gain political capital, given a serious warning or withdraw from their party posts disposition; if the circumstances are serious, to give Leave a party to observation or expelled from the party. (3) on against the organization review of the provisions of the constitution, party loyalty honesty is party members must comply with the obligations. Members must obey the organization decision, shall not violate the organization decided encounters by asking questions to find organization, rely on the organization, shall not deceive the organization, against the organization. For example, after the investigation does not take the initiative to explain the situation, but to engage inoffensive and defensive alliance, hiding the stolen money is against survey organization, is a violation of the behavior of political discipline. Article 24 of the original > < Regulations, although the provisions of the interference, hinder group review the behavior of the fabric can be severely or 13 Aggravated punishment, but did not put this kind of behavior alone as a discipline for qualitative amount of discipline. > < new regulations increase the Article 57, "anti organization review, one of the following acts, given a warning or serious warning; if the circumstances are relatively serious, giving removed from or placed on probation within the party post; if the circumstances are serious, give expelled from the party: (a) on supply or forged, destroyed, transfer, conceal evidence; (II) to prevent others expose, providing evidence Material; (III) harboring co personnel; (4) to the organization to provide false information, to hide the fact;(5) the him against the acts of the organization review. "< rule > add this clause to the Constitution requires more specific, the previous no punishment in accordance with the definite list and put forward clear punishment in accordance with. (4) about organizing or participating in superstitious activities as < Regulations > about engage in activities of。
配电柜出厂检验报告新编
项目名称：编号：
柜体名称
柜体规格
柜体类型
柜体数量
项目
检验项目及技术要求
检验结果
备注
绝缘
测试
1、相间电阻、及相线与中线电阻应大于500MΩ。
合格/不合格
耐压
测试
1、主电路带电部件与地（框架）之间，2500V在5秒无击穿、无闪络现象。
合格/不合格
2、主电路母排各相之间，2500V5秒无击穿、无闪络。主回路导线之间，750V5秒无击穿、无闪络，二次回路500V源自秒无击穿、无闪络。合格/不合格
保护电 路的连 续 性
1、主接地线与门（箱体）之间的的连续性试验，接地电阻<0.1Ω，试验电流为》10A
合格/不合格
2、主接地线与柜体裸露导电部件之间，接地电阻<0.1Ω，试验电流为》10A。
合格/不合格
通电
测试
1、按装置的电气原理图要求进行模拟动作试验，试验结果应符合要求，5次以上均正常动作。
合格/不合格
2、安装置的电气原理图要求进行故障模拟试验，其故障信号和报警指示应正确。
合格/不合格
3、通电试验时每个回路的一、二次接线均正确无误。
合格/不合格
4、各回路开关的容量应与图纸相符。
合格/不合格
显示
指示
1、各种标签标识必须与图纸、工艺测试指示相吻合。
合格/不合格
2、同一设备不同标示、指示应协调一致。
合格/不合格
质检综合结论：
检验部门：
质 检 人：
检验日期：
合格/不合格
性能
参数
1、变频器、软启动器、热继电器、时间继电、仪表等参数必须按所需功能设定。
合格/不合格
高压柜出厂例行检验报告
柜架表面涂覆：要求色泽均匀，漆膜无皱纹、流痕、起泡等。
元器件的型号应与图纸所选型号一致，应有合格证及检验报告
元器件的排列是否与图纸一致
铭牌及柜体清洁度检查：符合相关标准
2
装
配
质
量
检
查
零部件、元器件安装要符合图纸要求，安装牢固，排列整齐、合理。
母线：表面光滑、无锤痕，无毛刺，接触紧密，有防电化腐蚀措施。
相序及涂（标）色：相序及涂（标）色是否符合标准规定
二次回路接线符合图纸，符合工艺规定：线路整齐美观，线号清晰。
测量电气间隙
相间、相对地电气间隙应≥125mm
带电体距门电气间隙应≥155mm
测量爬电距离
有机绝缘爬电距离应≥240mm
3
操
作
试
验
主回路开关的动作性能检查
同类型、同规格可移开部件互换性检查，进出灵活无卡滞
42KV/1min
隔离断口
48KV/1min
辅助回路
2KV/1s
6
防护等级
柜体的防护等级应符合IP30
结论：本产品经试验、检测符合相关图纸设计及国家技术标准GB/T3906-83，产品合格。
检验：审核：日期：
记录编号
高压柜出厂例行检验报告
文件版本
项目名称
合同号
额定电压
母线规格
产品型号
产品编号
额定电流
防护等级
一次元件
型号规格
生产厂
出厂编号
数量
二次元件
型号规格
生产厂
出厂编号
断路器
保护装置
互感器
仪表
隔离开关
GGD低压配电柜使用说明书
GGD低压配电柜使用说明一、产品介绍1.用途及特点GGD型交流低压配电柜适用于发电厂、变电站、厂矿企业等电力用户作为交流50赫。
额定工作电压389V，额定工作电流至3150A的配电系统中，做为动力，照明及配电设备的电能转换、分配与控制之用。
根据能源部主管部门、广大电力用户及设计部门的要求，本着安全、经济、合理、可靠的原则而设计的新型低压配电柜。
产品具有分断能力高，动热稳定性好，结构新颖、合理，电气方案切合实际，系列性、适用性强、防护等级高等特点。
可作为更新换代的产品使用。
符合IEC439《低压成套开关设备和控制设备》，GB7251《低压成套开关设备》等标准。
2.产品型号及含义3.使用条件3．1 周围空气温度不高于40℃，不低于–5℃。
24h内的平均温度不得大于+35℃。
3．2 户内安装使用，使用地点的海拔高度不超过2000M。
3．3 周围空气相对湿度在最高温度为+40℃时不超过50%。
在较低温度时允许在较大的相对湿度（例如：20℃时为90%）应考虑到由于温度的变化可能会偶然产生凝露的影响。
3．4 设备安装时与垂直面的倾斜度不超过5度。
3．5 设备应安装在无剧烈震动和冲击的地方，以及不足使电器元件受到腐蚀的场所。
4.电气参数4．1 额定绝缘电压660V4．2 额定工作频率50HZ4．3 辅助电路的工作电压：交流：100V、220V、380V；直流：110V、220V。
4．3 额定工作电流GGD1：400A、600A（630）、1000AGGD2：1000A、1500A（1600）GGD3：2000A、2500A、3150A。
4．5 额定短路强度GGD1：分断能力 15KA 峰值耐受电流 30KAGGD2：分断能力 30KA 峰值耐受电流 63KAGGD3：分断能力 50KA 峰值耐受电流 105KA5. 柜体结构5．1 构架用8Mf冷弯型钢材局部焊接拼装而成。
其钢性及承载能力均达到电器元件的安装要求，构架上分别有按E= 20mm和E= 100mm模数排列的安装孔，以提高产品装配的通用性。
电气控制柜(箱)出厂检验报告单
电气控制柜( 箱) 出厂检验报告单
NO.
产品名称：型号规格：
产品编号：检验依据：GB7251.1-5
序
检测项目与技术要求检验方法检测结果号
面板平整、焊接均匀牢靠、无明显变形、涂层完好
一
元件安装牢固
般
1
目测检二次配线连接牢固、端头有标志、相序排列正确
查
接地等标志符合要求。
尺
门开启角度>90 度，灵活开启
2 寸
检
电气间隙：≥10mm
目测
卷尺爬电距离：≥15mm 查
导电部件与地之间、导电部件之间
介2500V 1S 无闪络或击穿
3 电
试
控制回路与地之间
2000V 1S 无闪络或击穿
CC2672 型
耐压测试仪验绝缘手柄对地
3750V 1S 无闪络或击穿
抽测接地电阻（电阻应≤100 mΩ）
4 保护
电路
连续
性试
a）开关支架与地
b）仪表门锁与地
CC2520 型
接地电阻测试仪验
通
5 电
试
按原理图、功能通电试验通电试验台验
本产品出厂检验结论：检验日期：检验员：。
低压配电柜产品出厂检验报告
产品出厂检验报告
产品编号
产品名称
产品型号规格
额定电流
检验员
山西恒开电气设备有限公司
20年月日
低压配电设备出厂检验记录
产品型号：电流（A）：出厂编号：150101文件号：HKDQ15002
序号
检验
项目
检验内容及方法
标准要求
实测值
一次
合格
修后
合格
1
一般检查
1）外观质量
柜体内外喷漆质量
柜体正面是无反射的桔形漆，正面和侧面涂层不允许有皱纹、气泡、透底等缺陷。色泽均匀，无明显刷痕、伤痕、机械杂质，表面漆色一致。
2000V，1s，无闪烙、无击穿
4
保护电路连续性验证
测量主接地点与保护电路任一点之间的电阻值。
通不小10A电流所有保护接地回路的接地电阻均小于100mΩ。
检查接地符号是否明显牢固。
(1)柜架操作机构以及内部主电路所装元件需接地的部位均保证良好的接地连续性。
(2)骨架有明显的接地标记。
(3)有接地装置专用的螺栓和垫圈。
(2)通电试验，一、二次线路正确，符合原理图要求。
(3)主开关在85%和110%额定电压下吸合动作可靠，在65%~110%分闸和35%~70%失压脱扣动作可靠
(4)电子式脱扣器参照开关技术参数进行
3
介电强度验证
主电路及与主电路直接连接的辅助电路试验电压为：（V）
2500V，1s，无闪烙、无击穿
不与主电路直接连接的辅助电路试验电压为：（V）
(3)二次回路接线正确，配线整齐美观，标号清楚。
(4)母线及二次回路导线均符合工艺求。
4）间隙和爬电距离
检查各导电回路带电部件之间及其金属结构件之间，母线与母线之间的电气间隙和爬电距离。
低压配电柜产品出厂检验报告
低压配电柜产品出厂检验报告一、产品基本信息：产品名称：低压配电柜产品型号：XXXXX生产日期：XXXX年XX月XX日生产厂家：XXXXX有限公司二、检验项目：1.外观检查：外观无划痕、变形、漏胶等情况。
2.尺寸测量：测量产品的长、宽、高，以确保与设计要求一致。
3.防护等级检测：通过测试确定配电柜的防护等级是否符合设计要求。
4.绝缘电阻检测：测量配电柜的绝缘电阻，以评估绝缘性能。
5.功能性能测试：测试低压配电柜的各项功能，确保各种保护装置能够正常运行。
6.开合闸试验：测试低压配电柜的开合闸动作是否正常、准确。
7.触电保护测试：测试低压配电柜的触电保护装置是否能够有效防止触电事故的发生。
8.电气参数测试：测试低压配电柜的电气参数，如电压、电流、频率等是否符合设计要求。
9.通讯功能测试：测试低压配电柜的通讯功能是否正常，如远程监控、远程操作等。
三、检验结果：1.外观检查：配电柜外观无划痕、变形、漏胶等情况。
2.尺寸测量：配电柜尺寸满足设计要求。
3.防护等级检测：配电柜防护等级符合设计要求。
4.绝缘电阻检测：配电柜绝缘电阻满足要求，无异常情况。
5.功能性能测试：各项功能正常，保护装置能够正常运行。
6.开合闸试验：开合闸动作正常、准确。
7.触电保护测试：触电保护装置能够有效防止触电事故的发生。
8.电气参数测试：电气参数符合设计要求。
9.通讯功能测试：通讯功能正常，远程监控、远程操作等功能可正常使用。
四、结论与建议：根据上述检验结果，我们认为该低压配电柜产品符合设计要求，并可以出厂销售。
建议用户在使用过程中按照使用说明书正确操作、维护设备，以确保设备的正常运行和使用寿命。
同时，厂家应继续加强质量控制，提高产品质量和性能，满足客户的需求和要求。
五、检验人员签名：检验人员：XXX。
配电柜出厂检验分析报告
质检综合结论：
检验部门：
质 检 人：
检验日期：
合格/不合格
2、安装置的电气原理图要求进行故障模拟试验，其故障信号和报警指示应正确。
合格/不合格
3、通电试验时每个回路的一、二次接线均正确无误。
合格/不合格
4、各回路开关的容量应与图纸相符。
合格/不合格
显示
指示
1、各种标签标识必须与图纸、工艺测试指示相吻合。
合格/不合格
2、同一设备不同标示、指示应协调一致。
合格/不合格
性能
参数
1、变频器、软启动器、热继电器、时间继电、仪表等参数必须按所需功能设定。
合格/不合格
品牌检验
1、元件器品牌型号应与图纸或者报价单一致。
合格/不合格
包
装
1、编号管、图纸、安装附件应齐全。
合格/不合格
2、柜面、显示部分或突出部分应有保护措施。
合格/不合格
3、包装应有方向说明及注意事项。
电控柜验收报告
项目名称：编号：
柜体名称
柜体规格检验项目及技术要求
检验结果
备注
绝缘
测试
1、相间电阻、及相线与中线电阻应大于500MΩ。
合格/不合格
耐压
测试
1、主电路带电部件与地（框架）之间，2500V在5秒无击穿、无闪络现象。
合格/不合格
2、主电路母排各相之间，2500V5秒无击穿、无闪络。主回路导线之间，750V5秒无击穿、无闪络，二次回路500V5秒无击穿、无闪络。
合格/不合格
保护电 路的连 续 性
1、主接地线与门（箱体）之间的的连续性试验，接地电阻<0.1Ω，试验电流为》10A
合格/不合格
GGD盘出厂检验报告
GGD 低压配电盘出厂检验报告
用户： 产品名称规格： 出厂编号：
1、外观检查：检查壳体外壁、漆膜、元器件安装及参数，电气间隙和爬电距
离、母线和布线、各部件紧固程度，防护及接地等。
应符合技术条件和图纸要求。
检查结果：
2、摇绝缘、打耐压
2.1、主进柜、联络柜及分路柜试验
2.2 无功功率补偿装置试验
3、拉合闸操作及通电检验
3.1、所有开关操作应转动灵活、可靠，位置指示正确固定牢固，电气接触良好；
3.2、电压指示仪表转动灵活无卡阻，指示正确； 3.3、信号灯指示符合技术条件和图纸要求； 3.4、照明回路符合图纸要求。
检验结果：
4、检验结论： 检验员：
年 月 日
绝缘缘YUA 缘电阻
A 、
B 、
C 短路后对地 测试结果 结论
绝缘电阻
MΩ
交流耐压
主回路各相对地2.5KV1分钟，无击穿、无飞弧
辅助电路对地2.5KV1分钟，无击穿、无飞弧 带电部件对手柄3.75KV1分钟，无击穿、无飞弧
项目
相别
A 对地
B 对地
C 对地 相之间 测试结果 结论
绝缘电阻
MΩ
MΩ
MΩ
MΩ
交流耐压 主回路各相对地2.5KV1分钟，无击穿、无飞弧
辅助电路对地2.5KV1分钟，无击穿、无飞弧
带电部件对手柄3.75KV1分钟，无击穿、无飞弧。
低压开关柜GGD,现场测试报告(空白)
柜门板接地点与保护导体之间
mΩ
8
介电强度试验
耐压值(2.5KV)应无击穿放电现象，测试时间为1秒钟。
手柄3.75KV 1秒钟，应无击穿和放电现象
.所有带电部件与裸露导电部件之间，施加电压2500V、施压时间5s，无击穿闪络。
每个极和连接到裸露导电部件上的所有其它极之间，施加电压2500V、施压时间5s，无击穿闪络。
mm
5
防护等级测量
IP30,直径2.5的钢丝，施加3N的力，钢丝应不能进入柜内
6
绝缘电阻
绝缘电阻(MΩ)电阻应不小于1 MΩ/V A+B+C+N-地
MΩ
7
工频过压保护
试验
将电容拆除，给装置接上电源，并将电容器开关投切开关闭合，在1.1~1.2倍的额定电压范围内，应在60秒内将电容器切除。
V秒
切除
8
保护电路的连续性检验
不由主电路直接供电的辅助电路与柜架之间，施加电压2500V、施压时间5s，无击穿闪络。
带电部件和用金属箔裹缠的绝缘操作手柄之间，施加电压3750V、施压时间5s，无击穿闪络。
总结论：
经
检验负责人：日期：客户签名：日期：
备注：
————————有限公司
低压成套开关设备产品安装现场测试报告
（依据标准GB7251.1-2005）第页共页
3
机械操作
对安装在装置内的开关电器及所有手动部件，机械操作5次，其机构动作应可靠、正常，连锁机构应符合要求
4
电气间隙、
爬电距离的测量
电气间隙≥8 mm
mm
爬电距离≥12.5 mm
mm
5
防护等级测量
IP30,直径2.5的钢丝，施加3N的力，钢丝应不能进入柜内
配电箱出厂检验报告兼质保书
5
紧固件
柜内用以固定电器元件及连接导线的紧固件应拧紧，并有防松措施。螺母应置于维护侧。
合格
6
保护接地
保护导体的截面面积应符合标准要求，具有保护电路对外接线的主接地端子或PE母排，其附近有耐久清晰的接地标志符号。设备通过直接的相互有效连接，或通过由保护导体完成的相互有效连接，以确保保护电路的连续性。
合格
3
主电路接线
母线搭接面应平整，具有防电化腐蚀措施，相色、相序符合标准要求，母线配置整齐美观，安装牢固，并便于装置内部的维修。采用绝缘导线敷设时，端部应加冷压接头，导电截面符合新产品的要求。
合格
4
辅助电路接线
辅助电路用绝缘铜导线的导电截面及线色应符合有关标准规定，配线整齐美观符合工艺要求，接线端头有耐久、清晰的标记头。
合格
7பைடு நூலகம்
喷涂层
表面喷涂层应具有良好的附着力，色泽均匀，同批装置不应有明显的色差。电镀件的镀层不应有起皮、脱落、发黑、生锈等缺陷。
合格
8
电器间隙与爬电距离
装置内不同相或极的裸露带电导体之间以及它们与未经绝缘的金属构件之间的电气间隙与爬电距离应符合标准规定的要求，电器元件内部以及其端子间的电气间隙与爬电距离应符合其技术条件的规定，在抽出式装置中电气间隙和爬电距离≥20mm当主电路母线连接件中某部分间距＜20mm可采用包扎绝缘。
合格
检验员：朱良平
检验科长：周俊
上海申泰电器有限公司
配电箱出厂检验报告兼质保书
执行标准：GB7251.3-2006
产品型号及规格
数量
1台
出厂日期
序
号
检验项目
技术要求
检测结果
1
结构和焊接
配电柜例行检验报告
产品检测中心
检验报告
.用户名称出厂编号
规格型号数量
序号试验项目技术要求检测仪器检验结果
1 一般
检查一、二次元件
符合图纸要求，有合格证，
安装正确牢靠
目测一、二次布线符合工艺要求目测铭牌及标志牢固、平整、正确、清晰目测
2 手动操
作试验
手动合分闸各5次正常手动
3 电器
间隙主电路之间
≥10mm
尺具
4 抽屉隔离距离≥20mm
5 爬电
距离
主电路之间≥12.5mm
6 通电
试验100%Un分合闸动作正常、线路无误
通电试验台电压表指示正常
电流表指示正常
7 介
电
强
度主电路带电部件对地2500V，1s无击穿无闪络
耐压试验台相间及相对地
2500V，1s无击穿无闪络
2500V，1s无击穿无闪络
2500V，1s无击穿无闪络
辅助电路带电部件对地2320V，1s无击穿无闪络
绝缘手柄和主电路之间3750V，1s无击穿无闪络
8 绝缘
电阻
相间及相对地≥1000Ω/V兆欧表
9 保护
导体
及连
续性
接地电阻
1、前(后)门接地电阻
接地电阻
测试仪
2、断路器支架对地
3、仪表门对地电阻
4、框架和主接地之间
5、元件安装板和主接地之间
6.抽屉对地
7、接地排对地
10 防护等级IP30 前、后、左、右、顶各面用
IP直径2.5mm硬钢丝不得
插入柜内
直径2.5
mm硬钢丝
产品按GB7251.1-2005进行检验和试验，结论：
检验员：日期：。
电柜质检报告模板
电柜质检报告模板
1. 报告简介
本报告为某电器公司生产的电柜产品质检报告，对电柜的性能及质量进行了全
面的检测和评估。
2. 器件和元件检测
器件和元件规格检测结果
电阻1kΩ合格
电容220nF 合格
二极管1N4001 合格
场效应管IRF740 合格
三极管2N3904 合格
电位器10kΩ合格
3. 转换器效率测试
在输入电压为220V情况下，对电柜的转换器进行了效率测试，得到以下结果：
输出电压输出电流输出功率输入电流输入功率效率
5V 2.5A 12.5W 1.5A 330W 3.79%
12V 1.5A 18W 1.8A 396W 4.55%
24V 0.8A 19.2W 2.2A 484W 3.97%
4. 过压和过流保护测试
测试结果表明，输入电压在265V时，电柜能够自动断开电源，起到了过压保
护的作用；当输出电流达到3A时，电柜也会自动断开电源，起到了过流保护的作用。
5. 综合评估
根据以上的测试结果及其他相关对比数据，电柜的质量达到了标准要求，并且
其使用寿命和稳定性也得到了保证。
6. 结论
本次检测证明，某电器公司生产的电柜产品达到了质量标准要求，并在性能、
稳定性和安全性等方面得到了保障。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
11
柜所有设备及母线
各坚固连接处应有防松装置
CB7251
12
汇流排坚固
并拧紧，所有紧固螺栓均经过热镀锌处理
IEC439
Q/OCK11-2001
13
多股软铜线线头两端接线工艺处理
导线两端须配用相同规格的线鼻子，用诊挤压方法作可靠连接。
IEC439
Q/OCK11-2001
GB7251
IEC439
2
三相动触头，全闸一致性
不小于产品使用说明书要求
GB7251
IEC439
3
三相动触与静触头的接触有效性
应保证有三分之二以上的有效接触面积
GB7251
IEC439生产厂使用说明书
五、主回路无载通电、操作试验
序号
检验项目
技术要求
引用标准
结果
1
测量和计量代表与互感器，变换器等更好的致性。
GB7251
IEC439
Q/OCK11-2001
10
保护接地线
甲16平方毫米黄、绿双色软芯铜线求软铜段与柜体的接点作紧固连接，并带有防松装置，以保证接地的连续性，压接地的安全点，仪表门的过门接地线，开关门的操作手柄，电流互器的SZ端及其它标有标记的地方
GB7251
IEC439
Q/OCK11-2001
14
单股铜芯线头两端接线工艺处理
线的圈方向，须按顺时针方向旋转。
IEC439
Q/OCK11-2001
15
GGD专用ZMJ型组合母线柜
规格及尺寸应与主母线汇流排的规格和尺寸相配合，并且装备应合理、正确、坚固、无松动。
LVLS设计要求
16
柜门上山型橡塑条
在仪表门断开门及后开门的折边处应装有符合要求的山型橡塑条，应嵌紧、不脱落。
编号：________________
GGD型交流低压配电柜
出厂检验报告
型 号：GGD
出厂编号 ：170108
泰凯非晶电气
GGD型交流低压配电柜出厂检验报告 第1页
一、柜体检验
序号
检验项目
技术要求
引用标准
结果
1
KS型基础柜架
采用20mm模桂孔的8m干型材
NLS设计要求
2
应用柜架
在基础柜架基础上，配用各种经喷塑处理过的安装梁式各类处理过的通用结构零部件。
NLS设计要求
3
相对应于每个主电路方案的变更的应用框架变更和重组其灵活性，通用性和可靠性
变更和重组各类带20mm，模桂孔的安装梁并配以相应的通用结构件，方能灵活自如，并且柜体的精度质量保持不变。
NLS设计要求
4
整个柜体的接地保护完整性和可靠性
主要接触部位用8m梅花螺钉，次要接触部位应用8m标准镀锌螺钉，装有电器元件的仪表门用多股软铜线与构架作可靠连接。
I251
IEC439
7
二次回路电气距离
不小于5mm
GB7251
IEC439
8
二次配线工艺
走线槽槽平竖直，工艺整齐，美观、布置合理，规。
GB7251
IEC439
Q/OCK11-2001
9
二次线径及颜色
二次回路导线选用黑色塑料铜芯线，其中接于电流回路的导线截面积为2.5平方毫米，接于电压控制回路的导线截面积为1.5平方毫米，在活动部分求可能受到弯曲的地方须采用多股软芯铜线引接，且套有阻燃软管，结束长擀，应保证其受弯半径大于10倍的线束外径。
GGD型交流低压配电柜出厂检验报告 第2页
二、装配检验
序号
检验项目
技术要求
引用标准
结果
1
电器元件安装
合理、规、元件有足够的爬电柜安、电器距离符合要求，元件有合格证，使用说明书，检验报告，质量可靠、有保证。
GB7251
IEC439
Q/OCK11-2001
2
母线外观及接触性
母排表面应无明显锤底，刮伤、母线搭接面应平整，用0.5mm塞干、塞入深度不大于5mm。
Q/OCK11-201
变化应一致，旦仪表指示状态正确
GB7251
IEC439
Q/OCK11-201
2
维电器保护
正常情况下，不动，故障与不正常工作情况下不拒动，且应有足够的可靠性。
GB7251
IEC439
Q/OCK11-201
3
自动空气开关及按装器
动作正确无误，自动空气开关分断可靠，无误，应具有来弧能力。
GB7251
IEC439
NLS设计要求
9
种类KS型8m干型钢的通用尺寸
符合相关的技术要求
GBYT304.1-82
10
各类KS型8m干型钢外观
表面裂纹、行刺，无破坏性压痕及严重锈蚀。
GBYT304.1-82
11
顶盖板及底部板的可拆性
装拆应灵活、方便以满足用户进、出线的特殊要求，且底板上应有数个ф80的高步落孔。
NLS设计要求
NLS设计要求
5
柜散热措施
柜上、下部均开有散热孔或栅网，其外壳防护等级不低于IP30。
空全对流原理不电力设备安全运行措施
6
仪表门前、后开门
关合门次数，应无卡阻和磨擦
GB7251
IEC439
7
静电喷塑
均匀、美观、无脱落、剩份、缺陷等
GB7251
IEC439
8
框架、安装梁、另部件之间的紧固连接
用镀锌螺栓作紧固连接，应可靠、牢固、无松动。
GB7251
IEC439
Q/OCK11-2001
3
相应排列
从设备正面观察，相应A相、B相、C相，垂直排列上、中、下，水平排列左、中、右，前后排列远、中、近。
GB7251
IEC439
Q/OCK11-2001
4
主回路电气距离
不小于10mm
GB7251
IEC439
5
主回路爬电距离
不小于12mm
GB7251
LVLS设计要求
17
门锁
门锁及销杆应装配正确门转动时应灵活，自如，无卡阻现象。
LVLS设计要求
18
主器件主柜涛清洁
柜体及柜所有电元器件及辅助设备应清洁，无灰尘、垃圾、污物等。
LVLS设计要求
GGD型交流低压配电柜出厂检验报告 第4页
三、断路检验
序号
检验项目
技术要求
引用标准
结果
1
设备部接线检验
正确、失误、符合产品说明要求
GB7251
ETC439
5
电动机传动操作试验
在0.85-1.1ue时，机构应正确工作
生产厂使用说明书
6
电动机传动操作试验
在0.85-1.1ue时，机构应正确工作
生产厂使用说明书
GGD型交流低压配电柜出厂检验报告 第5页
四、隔离开关检验
序号
检验项目
技术要求
引用标准
结果
1
三相断开口距
不小于产品使用说明书要求
生产厂使用说明书
2
手动及电动无载分工操作
其动作正确、失误、分、合、状态位置指示无误
GB7251、IEC439生产厂家使用说明书
3
分励脱扣器，操作试验
在07-1.lue之间的任一数值断路器应可靠工作
GB7251
ETC439
4
欠电压脱扣器位试验
在0.85-1.1ue之间的任一数值断路器应可靠接通，在小干0.34ue时，断路器可靠