EFM201中文资料
FlexiForce标准型号A201传感器说明书
DS Rev I 062821ISO 9001:2008 Compliant & 13485:2016 RegisteredThe FlexiForce A201 is our standard sensor and meets the requirements of most customers. The A201 is a thin and flexible piezoresistive force sensor that is available off-the-shelf in a variety of lengths for easy proof of concept. These ultra-thin sensors are ideal for non-intrusive force and pressure measurement in a variety of applications. The A201 can be used with our test & measurement, prototyping, and embedding electronics, including the FlexiForce Sensor Characterization Kit, FlexiForcePrototyping Kit, FlexiForce Quickstart Board, and the ELF™ System*. You can also use your own electronics, or multimeter.FlexiForce™Standard Model A201BenefitsPhysical PropertiesThickness 0.203 mm (0.008 in.)Length 191 mm (7.5 in.)** (optional trimmed lengths: 152 mm (6 in.), 102 mm (4 in.), 51 mm (2 in.))Width14 mm (0.55 in.)Sensing Area 9.53 mm (0.375 in.) diameterConnector3-pin Male Square Pin (center pin is inactive)Substrate Polyester Pin Spacing 2.54 mm (0.1 in.)✓ROHS COMPLIANT• Thin and flexible • E asy to use• C onvenient and affordable* Sensor will require an adapter/extender to connect to the ELF System. Contact yourTekscan representative for assistance.** Length does not include pins. Please add approximately 6 mm (0.25 in.) for pin length for a total length of approximately 197 mm (7.75 in).Typical PerformanceEvaluation ConditionsLinearity (Error)< ±3% of full scaleLine drawn from 0 to 50% loadRepeatability < ±2.5%Conditioned sensor, 80% of full force applied Hysteresis < 4.5% of full scaleConditioned sensor, 80% of full force appliedDrift< 5% per logarithmic time scaleConstant load of 111 N (25 lb)Response Time < 5µsecImpact load, output recorded on oscilloscope Operating Temperature -40°C - 60°C (-40°F - 140°F)Convection and conduction heat sources Durability≥ 3 million actuations Perpendicular load, room temperature, 22 N (5 lb)Temperature Sensitivity0.36%/°C (± 0.2%/°F)Conductive heating***All data above was collected utilizing an Op Amp Circuit (shown on the next page). If your application cannot allow an Op Amp Circuit, visit/flexiforce-integration-guides, or contact a FlexiForce Applications Engineer.***©Tekscan Inc., 2021. All rights reserved. Tekscan, the Tekscan logo, and FlexiForce are trademarks or registered trademarks of Tekscan, Inc.+1.617.464.4283|1.800.248.3669|****************|/flexiforceP urchase T oday o nline aT www .Tekscan .com /sToreVOLUMEDISCOUNTSA s k U sAb o u t Ou rSensing Area14 mm (.55 in.)191 mm (7.5 in.)6 mm (.25 in.)Actual size of sensorTrim LinesV OUT = -V REF * (R F / R S )• Polarity of V REF must be opposite the polarity of V SUPPLY • Sensor Resistance R S at no load is typically >1MΩ• Max recommended current is 2.5mAV OUTC 1R F V SS = GroundV DD = V SUPPLYC 1 = 47 pFR FEEDBACK (R F ) = 100kΩ POTENTIOMETER V REF OptionsSquare Wave Up to 5V , 50% Max Duty CycleDC0.25V - 1.25VMCP6004-V REF100K potentiometer and 47 pF are general recommendations; your specific sensor may be best suited with a different potentiometer andcapacitor. Testing should be performed to determine this.R SRecommended Circuit†This sensor can measure up to 4,448 N (1,000 lb). In order to measure higher forces, apply a lower drive voltage (-0.5 V, -0.25 V, etc.) and reduce the resistance of the feedback resistor (1kΩ min.). To measure lower forces, apply a higher drive voltage and increase the resistance of the feedback resistor.Sensor output is a function of many variables, including interface materials.Therefore, Tekscan recommends the user calibrate each sensor for the application.Standard Force Rangesas Tested with Circuit Shown4.4 N (0 - 1 lb)111 N (0 - 25 lb) 445 N (0 - 100 lb) †。
深圳市昇润科技HY-40R201低功耗蓝牙5.0模块规格书说明书
HY-40R201深圳昇润科技对本手册中可能出现的和/或规格书的权利，恕不另行通知用作生命支持设备或系统中的关键标是由美国蓝牙SIG公司所有.R201低功耗蓝牙 5.0模块规格书(40 pin)文档版本：V2.02017年10月25日深圳市昇润科技有限公司版权所有现的错误不承担责任。
此外，昇润科技保留随时行通知，并不承诺更新此处所包含的信息。
昇润的关键组件。
以及不承担各种专利或知识产权的.密级：公开资料留随时更改硬件，软件。
昇润的产品不被授权产权的授权使用;蓝牙商1.简述 (1)1-1应用： (1)1-2主要特征： (1)2. 产品型号 (2)2-1.(4 种天线形式可供选择)/( 可选: 带屏蔽罩或不带屏蔽罩) (2)2-2: HY-40R201PC机种屏蔽罩上FCC ID &( IC ID 待定义）印刷内容： (2)3. 模块尺寸与图片 (2)3.1 HY-40R201P / WMD40R201SR6P0 PCB IFA天线 (2)3-2.HY-40R201I /WMD40R201SR6I0 IPEX RF外接天线连接端子 (3)3-3. HY-40R201W / MD40R201SR6W0 金属线天线 (1/4波长偶极子天线) (3)3.4. HY-40R201C/ WMD40R201SR6C0 (陶瓷天线) (3)(4). 应用注意事项: (4)5.引脚分配和端口功能说明 (5)6. 电气特性 (6)6-1. 射频特性 及 电流功耗: (6)6-2. 绝对最大额定值 (7)6-3. ESD 额定值 (7)6-4.建议工作条件 (7)6-5.GPIO DC特性 (7)6-6. 时序要求 (8)6-7. 动作状态切换时序特性 (8)7. 模块方块图 (8)8.IC功能方块图 (9)9. 工作模式架构图 (9)10. 回流焊曲线建议 (无铅锡膏: Sn 96.5%, Ag 3%, Cu 0.5%) (10)11. HY-40R201PC / WMD40R201SR6PC 模块 FCC及 IC声明 (11)12.联系我们 (13)HY-40R201提供蓝牙低功耗特性：无线电，蓝牙协议栈，配置文件和客户应用程序的所需空间。
Quidway Eudemon 200E-C&200E-F 防火墙 硬件描述(V100R002_01)
1.2.1 产品外观................................................................................................................................................1-2 1.2.2 接口编号方法........................................................................................................................................1-4 1.3 设备参数.........................................................................................................................................................1-5 1.4 环境要求.........................................................................................................................................................1-5 1.4.1 储存环境................................................................................................................................................1-6 1.4.2 运输环境................................................................................................................................................1-8 1.4.3 运行环境..............................................................................................................................................1-10
REF01中文手册
REF01数据表1、元器件参数特性1）High output accuracy（高输出精度）REF01: 10.0 V, ±0.3% maximumREF02: 5.0 V, ±0.3% maximumREF03: 2.5 V, ±0.6% maximum2）Excellent temperature stability（良好的温度稳定特性）REF01: 8.5 ppm/°C maximumREF02: 8.5 ppm/°C maximumREF03: 50 ppm/°C maximum3）Low noise（低噪声）REF01: 30 µV p-p typicalREF02: 15 µV p-p typicalREF03: 6 µV p-p typical最高供电电压范围：最大达36 V最低供电电流：最大值为1.4 mA高负荷驱动能力：最大10 mA（最大输出负载电流）温度输出功能（温度监控）应用场景精密数据系统高分辨率转换器工业过程控制系统精密仪器军事和航空航天应用概述REF01/REF02/REF03系列精密电压参考产品提供了稳定的10.0 V、5.0 V或2.5 V输出，且随供应电压、环境温度或负载条件的变化影响最小。
该设备有8引脚的SOIC、PDIP、CERDIP 和TO-99封装，以及20端口的LCC封装（仅883），进一步提高了该设备在标准和高压力应用中的可用性。
通过一个外部缓冲器和一个简单的电阻网络，TEMP终端可以用于温度传感和近似。
在该装置上还提供了一个TRIM端子，用于微调输出电压。
REF01、REF02/REF03系列应用非常适合通用和空间受限的应用。
较新的设计应使用ADR01/ADR02/ADR03/ADR06系列参考文献，可提供更高的精度和温度。
1、引脚配置不同封装下的引脚图如下：注：NC = NO CONNECT ，即不要在这些引脚上连接任何东西。
菲尼克斯型号
菲尼克斯电气中国公司隶属于德国菲尼克斯电气集团。
1928年，菲尼克斯电气发明了世界上第一片组合式接线端子，这就是现代端子的雏形，也是菲尼克斯电气申请并获得的第一个发明专利。
此后，菲尼克斯电气激情创新，致力于各种连接技术的开发，形成了完善的电气接口技术体系，其中很多产品系列已经成为行业的应用标准。
菲尼克斯电气中国公司植根中国大地，努力开拓自己的业务。
如今中国公司的业务发展迅速，已经成为整个集团全球业务的重要基石。
2004年集团提出了新的战略，中国公司与德国、美国公司一起成为集团的核心竞争力中心，技术支持和管理范围拓展到亚洲太平洋地区。
MACX MCR-EX-SL-RPSSI-IMACX MCR-SL-CAC-5-IMACX MCR-SL-CAC-5-I-UPMCR-1CLP-I-I-00MCR-2CLP-I-I-00MCR-4CLP-I-I-00MCR-C-I-I-00-DCMCR-C-I-I-04-DCMCR-C-I-I-40-DCMCR-C-I-U-0-DCMCR-C-I-U-4-DCMCR-CLP-UI-I-4MCR-CPS-I-I-44-EMCR-CPSS-I-I-44-EMCR-C-UI/UI-DCIMCR-C-U-I-0-DCMCR-C-U-I-10B-0B-DCIMCR-C-U-I-4-DCMCR-C-UI-UI-DCI-NCMCR-C-U-U-DCMCR-FL-C-UI-2UI-DCIMCR-FL-C-UI-2UI-DCI-NCMCR-FL-C-UI-UI-DCI-24/230MCR-F-UI-DCMCR-PS- 24DC/24DC/200MCR-PS- 24DC/2X24DCMCR-PS- 24DC-10DC MCR-PT 100-IMCR-PT100/I/DCMCR-PT100-UMCR-R-I-4-V-DCMCR-S-1/5-UI-DCIMCR-S-10/50-UI-DCI MCR-S10-50-UI-DCI-NC MCR-S-1-5-UI-SW-DCI-NC MCR-SL-1CLP-I-I-00-4KV MCR-SL-D-U-IMCR-SL-PT100-I-DC-24 MCR-SL-PT100-SPMCR-SL-S-1-5-I-DCI-230 MCR-SL-S-1-5-I-DCI-24 MCR-SL-S-16-SP-24 MCR-SWS-IMCR-SWS-UMCR-TE-JK-I-EMCR-T-UI-EMCR-T-UI-E-NCMCR-T-UI-NCMCR-VAC-UI-O-DCMCR-VDC-UI-B-DCMCV 1,5/ 2-G-3,5MCV 1,5/ 5-G-3,5MCV 1,5/ 8-G-3,5MCV 1,5/12-G-3,5 MCV 1,5/14-G-3,5MCV 1,5/16-G-3,5MCV 1.5/2-G-3.81MCV 1.5/6-GF-3.81 MCV 1.5/8-GF-3.81 MCVR 1.5/11-ST-3.81 MDSTB 2,5/10-G1-5,08 MDSTB 2,5/12-G1-5,08 MDSTB 2,5/20-G1-5,08ME 6,2 TBUS-2 1,5/5-ST-3,81 GN MINI MCR-SL-1CP-I-IMINI MCR-SL-2CP-I-IMINI MCR-SL-I-IMINI MCR-SL-PT100-UI-SPMINI MCR-SL-PTBMINI MCR-SL-RPS-I-IMINI MCR-SL-RPS-I-I-SPMINI MCR-SL-R-UIMINI MCR-SL-UI-2IMINI MCR-SL-UI-2I-NCMINI MCR-SL-UI-UIMINI MCR-SL-U-U-SPMINI-PS-100-240AC/ 5DC/3MINI-PS-100-240AC/10-15DC/2 MINI-PS-100-240AC/10-15DC/8 MINI-PS-100-240AC/24DC/MINI-PS-100-240AC/24DC/2MINI-PS-100-240AC/24DC/4MINI-PS-100-240AC/2X15DC/1 MINI-SYS-PS-100-240AC/24DC/1.5 PLC-BSC- 24DC/1/ACTPLC-BSC- 24DC/1/SENPLC-BSC- 24DC/21PLC-BSC- 24DC/21/SO46PLC-BSC- 24DC/21-21PLC-BSC- 24DC/21HCPLC-BSC- 24UC/21PLC-BSC- 24UC/21-21PLC-BSC- 48DC/21PLC-BSC- 48DC/21-21PLC-BSC- 48DC/21HCPLC-BSC-120UC/21-21/SO46PLC-BSC-230UC/1/SENPLC-BSC-230UC/21PLC-BSC-230UC/21/SO46PLC-BSC-230UC/21-21PLC-BSC-230UC/21-21/SO46 PLC-BSC-230UC/21HC/SO46 PLC-BSP- 24DC/1/ACTPLC-BSP- 24DC/21PLC-BSP- 24DC/21-21PLC-BSP- 48DC/21PLC-BSP- 48DC/21-21PLC-BSP-230UC/21/SO46PLC-ESK GYPLC-OSC- 24DC/24DC/2PLC-OSC- 24DC/48DC/100 PLC-OSC- 24DC/48DC/100/SEN PLC-OSC-230UC/48DC/100 PLC-OSP- 12DC/300DC/1PLC-OSP- 24DC/230AC/1PLC-OSP- 24DC/24DC/10PLC-OSP- 24DC/24DC/2PLC-OSP- 24DC/24DC/2/ACT PLC-RSC- 12DC/21PLC-RSC- 12DC/21-21PLC-RSC- 24DC/1/ACTPLC-RSC- 24DC/1-1/ACTPLC-RSC- 24DC/1IC/ACTPLC-RSC- 24DC/21PLC-RSC- 24DC/21-21PLC-RSC- 24DC/21AUPLC-RSC- 24DC/21HCPLC-RSC- 24UC/21PLC-RSC- 24UC/21-21PLC-RSC-120UC/21PLC-RSC-120UC/21-21PLC-RSC-230UC/1AU/SENPLC-RSC-230UC/21PLC-RSC-230UC/21/SO46PLC-RSC-230UC/21-21PLC-RSC-230UC/21-21/SO46 PLC-RSC-230UC/21HCPLC-RSP- 24DC/1/ACTPLC-RSP- 24DC/1AU/SENPLC-RSP- 24DC/21PLC-RSP-230UC/1/SENPLC-RSP-230UC/1AU/SENPLC-RSP-230UC/21PLC-RSP-230UC/21-21PLC-V8/FLK14/INPLC-V8/FLK14/OUTPND ADAPTER VGA USBPOWERSET BC/3/FM/PLUSPOWERSET BC/3+1/FMPOWERSET BC/3+1-100/FMPOWERSET-BC-CTRL/KYPPC 5315 PMPPS BASIC I/MPPS CD MPPS STANDARD I/MPR2-BSC3/4X21通用型初级开关电源2938578 QUINT-PS-100-240AC/24DC/2.5 2938581 QUINT-PS-100-240AC/24DC/5 2866255 QUINT-PS-100-240AC/48DC/5 2938594 QUINT-PS-3X400-500AC/24DC/5 2938811 QUINT-PS-100-240AC/12DC/10 2938604 QUINT-PS-100-240AC/24DC/10 2938248 QUINT-PS-100-240AC/48DC/10 2938617 QUINT-PS-3X400-500AC/24DC/10 2938219 QUINT-PS-3X400-500AC/48DC/10 2938620 QUINT-PS-100-240AC/24DC/20 2938976 QUINT-PS-100-240AC/48DC/20 2938727 QUINT-PS-3X400-500AC/24DC/ 20 2938222 QUINT-PS-3X400-500AC/48DC/20 2938633 QUINT-PS-3X400-500AC/24DC/30 2938879 QUINT-PS-100-240AC/24DC/40 2938646 QUINT-PS-3X400-500AC/24DC/40 2866378 QUINT-PS-24DC/24DC/102938196 QUINT-PS-ADAPTERS7/12938206 QUINT-PS-ADAPTERS7/22866857 QUINT-ADAPTER/42938235 UWA 182/52超薄设计的初级开关电源2938714 MINI-PS-100-240AC/ 5DC/3 2938743 MINI-PS-100-240AC/2X15DC/1 2938756 MINI-PS-100-240AC/10-15DC/2 2866297 MINI-PS-100-240AC/10-15DC/8 2938840 MINI-PS-100-240AC/24DC/1 2866446 MINI-PS-100-240AC/24DC/1.3 2938730 MINI-PS-100-240AC/24DC/2 2938837 MINI-PS-100-240AC/24DC/4 2866336 MINI-PS-100-240AC/24DC/C2LPS 2866271 MINI-PS-48-60DC/24DC/1 2866284 MINI-PS-12-24DC/24DC/1 2866983 MINI-SYS-PS-100-240AC/24DC/1.5 阶梯设计的初级开关电源2938918 STEP-PS-100-240AC/ 5DC/4 2938921 STEP-PS-100-240AC/12DC/3 2938934 STEP-PS-100-240AC/15DC/2.4 2938947 STEP-PS-100-240AC/24DC/1.5 2938950 STEP-PS-100-240AC/48DC/0.75菲尼克斯电压隔离转换模块2766821 MCR-PS- 24DC/24DC/2002781877 MCR-PS- 24DC/2X24DC2940676 EG 45-PS-230AC/ 5DC/250 2940618 EG 45-PS-230AC/24DC/250防爆型初级开关电源和冗余模块2938853 QUINT-PS-100-240AC/24DC/5/EX 2938866 QUINT-PS-100-240AC/24DC/10/EX 2938963 QUINT-DIODE/40菲尼克斯不间断初级开关电源2866213 QUINT-BUFFER/24DC/202866226 QUINT-DC-UPS/24DC/102866239 QUINT-DC-UPS/24DC/202866242 QUINT-DC-UPS/24DC/402866349 QUINT-BAT/24DC/3.4AH2866352 QUINT-BAT/24DC/7.2AH2866365 QUINT-BAT/24DC/12AH菲尼克斯初级开关电源单元2866268 TRIO-PS/1AC/24DC/2.52866310 TRIO-PS/1AC/24DC/52866323 TRIO-PS/1AC/24DC/102866459 TRIO-PS/3AC/24DC/102866381 TRIO-PS/1AC/24DC/202866394 TRIO-PS/3AC/24DC/202866404 TRIO-PS/3AC/24DC/40菲尼克斯电压调整模块2954963 EMG 45-NZG/G 5/SI2943903 EMG 30-NZG/G 5/SI2954976 EMG 45-NZG/G12/SI2943916 EMG 30-NZG/G12/SI2954992 EMG 45-NZG/G15/SI2943929 EMG 30-NZG/G15/SI2954989 EMG 45-NZG/G24/SI2943932 EMG 30-NZG/G24/SI2941060 EMG 75-NZG/G 5/22941057 EMG 75-NZG/G12/22941044 EMG 75-NZG/G15/22942454 EMG 75-NZG/G24/22736686 ASI QUINT 100-240/2.4 EFD2736699 ASI QUINT 100-240/4.8 EFD2943738 EMG 45-SD-D/LA/SI2940825 EMG 45-SD-D/LA/SI YE2941523 EMG 90-2SD-D/LA菲尼克斯防雷器、菲尼克斯浪涌保护器：菲尼克斯电源第一级防雷器2858467 AEC组合防雷器 POWERSET BC/3+1-100/FM1 2816881 电源第一级防雷器 FLT 35/3 通流量35KA（三相）2 2817482 电源第一级防雷器 FLT 35/3+1 通流量35KA（三相）3 2838940 电源第一级防雷器 FLT 35-260 通流量35KA（单相）4 2816904 电源第一级防雷器 FLT 50 N/PE 通流量50KA（N-E）5 2838160 电源第一级防雷器 FLT 100-260 通流量100KA（单相）6 2809717 电源第一级防雷器 FLT 25-400 通流量25KA7 2748603 电源第一级防雷器 FLT 60-400 通流量60KA8 2816386 电源第一级防雷器 FLT-PLUS 通流量50KA9 电源第一级防雷器 FLT 25-400/3+1 通流量50KA10 2856317 电源第一级防雷器 FLT 35/3+1 CTRL-0.9/I 通流量35KA（三相带指示灯）11 2856304 电源第一级防雷器 FLT 35/3 CTRL-0.9/I 通流量35KA（三相带指示灯）12 2817411 电源第一级防雷器 FLT 35 CTRL-0.9 通流量35KA（单相）13 2817424 电源第一级防雷器 FLT 35 CTRL-0.9/I 通流量35KA（单相，带指示灯）14 2817453 电源第一级防雷器 FLT 50 N/PE CTRL-1.5 通流量50KA（N-E）15 2818643 电源第一级防雷器 FLT-PLUS CTRL-0.9 通流量50KA,残压0.9KV16 2818960 电源第一级防雷器 FLT-PLUS CTRL-0.9/I 通流量50KA,残压0.9KV 电源第二级防雷器特价供应菲尼克斯电源，菲尼克斯安全栅，菲尼克斯端子，菲尼克斯继电器，大量库存.17 5772061 电源第二级防雷器 VAL-MS 320/1+1 通流量40KA单相8/20us、耐压320V18 5772074 电源第二级防雷器 VAL-MS 320/1+1-FM 同上、带遥信19 5772029 电源第二级防雷器 VAL-MS 230/1+1 通流量40KA单相8/20us、耐压275V20 5772032 电源第二级防雷器 VAL-MS 230/1+1-FM 同上、带遥信21 5772045 电源第二级防雷器 VAL-MS 230 IT/1+1 通流量40KA单相8/20us、耐压385V22 5772058 电源第二级防雷器 VAL-MS 230 IT/1+1-FM 同上、带遥信23 2838209 电源第二级防雷器 VAL-MS 230/3+1 通流量40KA三相8/20us24 2858548 电源第二级防雷器 VAL-MS 230 IT/3+1 通流量40KA三相8/20us25 2838199 电源第二级防雷器 VAL-MS 230/3+1 FM 通流量40KA（带遥信）三相8/20us26 2858551 电源第二级防雷器 VAL-MS 230 IT/3+1-FM 通流量40KA（带遥信）三相8/20us27 2858564 电源第二级防雷器 VAL-MS 320/3+1 通流量40KA三相8/20us28 2858577 电源第二级防雷器 VAL-MS 320/3+1-FM 通流量40KA三相8/20us29 直流48V防雷器 VAL-MS 60 通流量40KA（不带遥信）30 2817987 电源第二级防雷器 F-MS 12 通流量40KA（N-E）31 2817974 电源第二级防雷器 F-MS 12/FM 通流量40KA（N-E，带遥信）电源第三级防雷器32 2858357 电源第三级防雷器 PT 2-PE/S-230AC 通流量10KA、单相33 2839389 电源第三级防雷器 CBT-4MS 通流量5KA、4孔34 2762100 电源第三级防雷器 MT-4PE-230AC 通流量6.5KA、三相34 电源第三级防雷器 CBT-SCHUKO 通流量6.5KA、三相退耦器35 2749660 退耦器 LT35 额定电流35A36 2818546 退耦器 LT63 额定电流63A信号防雷器37 2839541 馈线防雷器 CF-UB-280DC-SB-SET 带接头38 2818148 馈线防雷器 CN-UB-280DC-SB N接头39 2809490 2M线防雷器 CN-UFB-5DC/E-LAN40 2782300 2M线防雷器 C-UFB-5DC/E2782313 C-UFB-24DC/E41 2838555 ISDN防雷器 CTM ISDN 插拔式42 2748276 ISDN防雷器 D-TR1/ISDN-A/RJ45-BB RJ4543 2838539 ADSL/电话线 CTM 1x2-110AC44 2838513 DDN CTM 1x2-24DC45 2838610 CTM接地架 CTM 10-MAG46 2765547 CTM接地架 CT 1-10-ES47 2818795 电话线防雷器 D-FM-A/RJ45-BB RJ45接口48 2838937 模拟电话信号 MT-2FM-RJ12 2路接口（RJ12接口）49 2858043 DDN/桢中继 PT3-HF-12DC-ST 插头，工作电压12V50 2856113 DDN/桢中继 PT 1x2-BE PT1＊2底座51 2818973 以太网防雷器 D-LAN-A/RJ45-BS RJ45接口52 2838050 广域网防雷器 D-DS1-A/RJ45-BB53 2749644 无线收发设备防雷器 C-RF54 2818067 有线电视防雷器 CF-TV-30DC-BB F接口55 2749631 有线电视防雷器 C-TV DIN接口56 2762278 RS485 MT-RS485/S57 2782601 RS485 D-UFB-485/BS-B58 2796118 V.11/RS-422 D-UFB-V11/SB-B59 2762773 V.24/RS-232C D-UFB-V24/S-DSUB 9/SB-B60 2763701 视频信号防雷器 C-UB/E61 2782245 视频信号防雷器 C-UB62 2838050 T1/E1 D-DS1-A/RJ45-BB RJ45接口63 2838228 4-20mA模拟信号防雷器 PT 2x2-24DC-ST 通流量10KA(插头)，2路保护UK1.5NUK1.5N BUUK2.5B UK2.5B BUUK3NUK3N BUUK 5NUK 5N BUUK 6NUK 6N BUUK 10NUK 10N BUUK 16NUK 16N BUUIK 35UIK 35 BUUK 35UKH 50UKH 50 BUUKH 95UKH 95 BUUKH 150UKH 150 BUUKH 240USLKG 1.5NUSLKG 2.5USLKG 3USLKG 5USLKG 6NUSLKG 10NUSLKG 16NUISLKG 35USLKG35USLKG50USLKG95UK 5-MTK-P/PUK 5-HESIUK 5-HSILED 24UK 5-HESILA 250 UK 10-DREHSI(5×20) URTK/SMBK 5/E-ZMBK 3/E-ZMBKKB 2.5UK 3-TWINUK 10-TWINUK 5-TWINUDK3UDK3-PEUDK4UDK4 BUUDK4-MTK-P/PUKK3UKK3 BUUKK5UKK5 BUDIK 1.5DIKD 1.5DOK 1.5URTKK 6-CAK4AK16AK35AKG 4 BUAKG 4 GNYEAKG 4 BKAKG 16 BUAKG 16 GNYEAKG 16 BKAKG 35 BUAKG 35 BKAZK 35D-URTKD-UK 2.5D-UK 4/10D-UK 16TS-RTKATS-RTKTS-KK3TS-KATP-UKATP-UK 5-MTKTP-UK35D-MBKKB 2.5DP-MBKKB2.5D-MBK/ED-UK 5-TWIND-UKK 3/5DP-UKK3/5DG-UKK3/5D-UDK4ATP-UKK3/5MPS-IH WHMPS-IH RDMPS-IH BUMPS-IH YEMPS-IH GNMPS-IH VTMPS-IH GYMPS-IH BKMPS-MTSAGK 10-UKH50AGK 10-UKH95AKG 10-UKH 150/240 UKH 50 EPUKH 150/240 EPFB10-6FB10-8FB10-10FB10-12FB2-15FB3-15FBRN 10-4NFBRI 2-5NFBRI 3-5NFBRI 4-5NFBRI 5-5NFBRI 10-5NFBRNI 2-5NFBRNI 3-5NFBRNI 10-5NFBI 2-6FBI 3-6FBI 5-6FBI 10-6FBI 2-8FBI 3-8FBI 5-8FBI 10-8FBI 2-10FBI 3-10 FBI 5-10 FBI 10-10FBI 10-12FB2-RTK/SFB3-RTK/SFB5-RTK/SFB10-RTK/SFBI 2-15FBI 3-15FBI 5-15FBI 2-20ISSBI 10-6ISSBI 10-10 ISSBI 10-8EB 10-5EB 3-5EB 2-5EBL 10-5EBL 2-5EBL 3-5EB 10-6EB 3-6EB 2-6EB 10-8EB 3-8EB 2-8EBS 10-8 EBS 3-8 EBS 2-8EB 10-10EB 3-10EB 2-10EB 10-12EB10-15EB 80-DIK BUEB 80-DIK RDSB 2-RTK/SSB 4-RTK/SUSB 2-RTK/SASB 2-RTK/SIS-K 4IS-K 10USBR 2-7KSS 6KSS 3-6 KSS 4-8 KSS 8RPSPS-IH WHPS-IH BUPS-IH YEPS-IH GNPS-IH VTPS-IH GYPS-IH BKPS-MTPSBJ 3/13/4 PSB 6/5/6 PSB 4/7/6PSB 3/10/4WS 3-6WS 3-8WS 4-6WS 4-8WS 4-15WS 5-6WS 5-8WS 5-15WS 3/4-UKH 50/25WS 4/5-UKH 50/25KLM-A+ES/KLM-GBUBE/D+ES/KMK3ST 1.5ST 1.5 BUST 2.5 ST 2.5 BUST4ST4 BUST6ST6 BUST10ST10 BUST16ST16 BUST35ST35 BUSTS2.5STS 2.5 BUSTS4 STS4 BUST1.5-PEST2.5-PEST4-PEST6-PEST 10-PEST 16-PEST 35-PESTS2.5-PESTS4-PEMZB1.5MZB1.5-NS35 MZDB1.5MZDB1.5-NS35MZB1.5-FMZB1.5-MMZDB1.5-FMZDB1.5-MMZB1.5-RZMZDB1.5-RZMZB1.5-PEMZB1.5-NS35-PEZRTK4ST1.5-TWINST2.5-TWINST4-TWIN ST6-TWINSTS2.5-TWINSTS4-TWINST1.5-QUATTROST2.5-QUATTROST4-QUATTROSTS4-QUATTROSTS2.5-QUATTROSTTB1.5STTB2.5STTB4ST1.5-TWIN-P E ST1.5-QUATTRO-PEST2.5-TWIN-PEST2.5-QUATTRO-PEST4-TWIN-PEST4-QUATTRO-PESTS4-TWIN-PESTS4-QUATTRO-PESTS2.5-TWIN-PESTS2.5-QUATTRO-PESTTB2.5-PEST2.5-MTST2.5-TGST4-HESI(5×20)ST2.5/1P ST2.5-QUATTRO/2P STTB2.5/2PSP2.5/1-LSP2.5/1-MSP2.5/1-RSPB2.5/1-LSPB2.5/1-MSPB2.5/1-RSPDB2.5/1-LSPDB2.5/1-MSPDB2.5/1-RFBS2-4FBS3-4FBS4-4FBS5-4FBS10-4FBS20-4 FBS2-5FBS3-5FBS4-5FBS5-5FBS10-5FBS20-5FBS2-6FBS3-6FBS4-6FBS5-6FBS10-6FBS20- FBS2-8FBS3-8FBS4-8FBS5-8FBS10-8FBS2-10FBS2-12FBS2-16D-MZB1.5D-MZB1.5-FD-MZB1.5-NS35D-ST2.5D-ST4D-ST6D-ST10D-ST16D-STS2.5D-STS4D-ST2.5-TWIND-ST4-TWIND-ST2.5-QUATTROD-ST4-QUATTROD-STTB2.5D-STTB4D-ZRTK4DS-ST2.5DS-ST4ATP-ST4ATP-ST4 QUATTROZB空白标识条ZB:数字标识条普通（1-100）ZB:数字标识条特殊打印ZBFM4/WH:UNBEDRUCKT ZBFM5/WH:UNBEDRUCKT ZBFM6/WH:UNBEDRUCKTZBFM4:SO/CMSZBFM5:SO/CMSZBFM6:SO/CMSZBFM7:SO/CMSB-STIFT 记号笔NS35/7.5 1M PERFORATED NS35/7.5 1M UNPERFORATED NS15 GELOCHT METER(带孔) NS15 UNGELOCHT METERNS32 GELOCHT METERNS32 UNGELOCHT METERNS35/7.5 UNGELOCHT METER NS35/7.5 GELOCHT METER NS35/15 UNGELOCHT METER NS35/15 GELOCHT METER NLS-CU3/10 1ME/UK1E/UKE/AL-NS32E/AL-NS35CLIPFIX35AB/SSAP2 METERAP3 METERAP2-TUAP3-TUAP-ESAI0.5-8WHAI0.75-8BU AI 1-8RDAI 1.5-8BKAI2.5-8GYAI4-10OGAI6-12GNAI10-12BNAI16-12WHAI25-16BKAI35-16RDAI50-20BUAI120-27BUAI70-20YEAI95-25RDAI-TWIN 2×0.75-8GYAI-TWIN 2×1-8RDAI-TWIN 2×1.5-8BKAI-TWIN 2×2.5-10BUAI-TWIN 2×4-12GYCUTFOX EBCUTFOX FBCUTFOX35PPS STANDARD I/MPPS BASIC I/MCRIMPFOX ZA 3CRIMPFOX UD 6-4CRIMPFOX UD 10-4CRIMPFOX UD 6-6CRIMPFOX INC 6 CRIMPFOX-4.0-ED-2.50 CF3000-2.5ZAP 25TZAP 100TSZF 1-0.6X3.5QUICK-WIREFOX6QUICK-WIREFOX 2.5CYCLOPSNS 15 PERFORATED 1MNS 15 UNPERFORATED 1MNS 35/7.5 PERFORATED 1MNS 35/7.5 UNPERFORATED 1MNS 32 PERFORATED 1MNS 32 UNPERFORATED 1MNS 35/15 PERFORATED 1MNS 35/15 UNPERFORATED 1MOTTA2.5OTTA6OTTA6-P/P OTTA6-T-P/POTTA6-TOTTA 6-PEOTTA2.5-PEOTTA2.5-P/POTTA25-M5OTTA25-M6UK35 BUURTK6D-OTTA2.5D-OTTA25D-OTTA6D-OTTA6-TATP-OTTAUT2.5UT2.5 BUUT2.5-PEUT2.5/1PUT2.5/1P BUUT2.5/1P-PEUT4UT4 BUUT4-PE UT4-DIO/L-R UT4-DIO/R-LUT4-HEDIUT4-HEDI BUUT4-HEDI-P/PUT4-HESI(5×20)UT4-HESILA 250UT4-HESILED 24UT4-HESILED 60UT4-MTUTF-MT BU UT4-MTD BU UT4-MTD-DIO/L-R-P/P UT4-MTD-DIO/R-L-P/P UT4-MTD-PEUT4-MTD-PE/SUT4-MT-P/PUT4-MT-P/P BUUT4-MT-P/P OGUT4-TGUT4-TG-P/PUT6UT6 BUUT6-PEUT10UT10 BUUT10-PEUT16 UT16 BUUT16-PEUT35UT35 BUUT35-PED-UT 2.5/10D-UT 2.5/1PD-UT16ATP-UTQTC1.5QTC1.5 BUQTC1.5-PEQTC1.5-QUATTRO QTC1.5-QUATTRO BU QTC1.5-QUATTRO-PE QTC1.5-TWINQTC1.5-TWIN BU QTC1.5-TWIN-PE QTC2.5QTC2.5 BUQTC2.5-PEQTC2.5-TWINQTC2.5-TWIN BU QTC2.5-TWIN-PED-QTC1.5D-QTC1.5-QUATTRO D-QTC1.5-TWIND-QTC2.5D-QTC2.5-TWINATP-QTCATP-QTC QUATTROATP-QTC TWINATP-QTTCBHDFK10 HDFKV10HDFK16HDFKV16HDFK25HDFKV25HDFK95HDFKV95HDFK4HDFKV4HDFK50HDFKV50ST4-HESILED24(5X20)ST4-HESILED24(6.3X32)MC1.5/2-GF-3.81MCV1.5/2-GF-3.81MC1.5/2-STF-3.81MC1.5/3-GF-3.81MCV1.5/3-GF-3.81MC1.5/3-STF-3.81MC1.5/4-GF-3.81MCV1.5/4-GF-3.81MC1.5/4-STF-3.81MC1.5/5-GF-3.81MCV1.5/5-GF-3.81MC1.5/5-STF-3.81MC1.5/6-GF-3.81MCV1.5/6-GF-3.81MC1.5/6-STF-3.81MC1.5/7-GF-3.81MCV1.5/7-GF-3.81 MC1.5/7-STF-3.81 MC1.5/8-GF-3.81MCV1.5/8-GF-3.81MC1.5/8-STF-3.81MC1.5/9-GF-3.81MCV1.5/9-GF-3.81MC1.5/9-STF-3.81MC1.5/10-GF-3.81MCV1.5/10-GF-3.81MC1.5/10-STF-3.81MC1.5/11-GF-3.81 MCV1.5/11-GF-3.81 MC1.5/11-STF-3.81MC1.5/12-GF-3.81MCV1.5/12-GF-3.81MC1.5/12-STF-3.81MC1.5/13-GF-3.81MCV1.5/13-GF-3.81MC1.5/13-STF-3.81MC1.5/14-GF-3.81MCV1.5/14-GF-3.81MC1.5/14-STF-3.81MC1.5/15-GF-3.81MCV1.5/15-GF-3.81MC1.5/15-STF-3.81MC1.5/16-GF-3.81MCV1.5/16-GF-3.81MC1.5/16-STF-3.81UTA159 MSTBV2.5/6-GF-5.08 MVSTBR2.5/6-STF-5.08MSTBV2.5/7-STF-5.08MUSTBR2.5/7-STF-5.08MSTBV2.5/11-GF-5.08MVSTBR2.5/11-STF-5.08MSTBV2.5/20-GF-5.08MVSTBR2.5/20-STF-5.08MDSTBV2.5/16-GF-5.08UMSTBVK2.5/2-G-5.08UMSTBVK2.5/3-G-5.08DFK-MSTB2.5/6-G-5.08DFK-MSTB2.5/10-G-5.08UMK-SE-11.25DFK-MSTB2.5/10-GF-5.08FRONT4-H-7.62MDSTB2.5/2-GFL-5.08MDSTB2.5/2-GFR-5.08AI-TWIN2*0.5-8WHAI0.5-6WH REL-MR-12DC/21REL-MR-24DC/21PLC-OSC-24DC/24DC/2PLC-BSC-24DC/21QUINT-PS-100-240AC/24DC/10 QUINT-PS-100-240AC/24DC/5PLC-RSC-48DC/21-21PLC-BSP-24DC/21(底座)PLC-RSP-24DC/21PLC-BSC-230UC/21(底座)DPT-24DC/24DC/2PLC-OSC-230UC/48DC/100MPS-MTMPS-1H-RDSZS0.6*3.5URTK/S-BEN ST2.5-QUATTRO-DI0/L-R MBKKB2.5-DI0/0-UKMKKMK2KMK3KMK4UKKB10ZDMTK 2.5ZDMTK 2.5 BUST-BEUK4-TGAI0.75-6GYAI2.5-8BUAI6-12YEMBK2.5/EST2.5-QUATTRO BU ST4-QUATTRO BUMZB1.5-MMZB1.5-F MBK 5/E-TG UBE+ES/KMK3SZF0-0.4*2.5SZF2-0.8*4.01B 1L AO 1/SFSZS0.4*2.5UK10-PLUSUK10-DREHSI(6.3*32) ZFK6-DREHSI(6.3*32) ESL 40*17DP-UKK3/5DG-UKK3/5MTK-P/PST6-TWIN BUD-ST6 TWIN ST6-TWIN AI1.5-10BKMKDSN1.5/2-5.08 MKDSN1.5/3-5.08 MKDS1.5/2-5.08 MKDS1.5/3-5.08 MKDS3/2-5.08MKDS3/3-5.08 MKDSP1.5/2-5.08 MKDSP1.5/3-5.08 SMKDSP1.5/2-5.08 SMKDSP1.5/3-5.08 MKKDSN1.5/2-5.08 MKKDSN1.5/3-5.08 MKKDS1.5/2-5.08 MKKDS1.5/3-5.08 MKKDS3/2-5.08 MKKDS3/3-5.08 GMKDS1.5/2-7.62 GMKDS1.5/3-7.62GMKDS3/2-7.62GMKDS3/3-7.62FRONT2.5-H/SA5D-FRONT2.5-V-O.Z.D-FRONT2.5-H-O.Z.FRONT2.5-V/SA5FFKDS/V-2.54FFKDS/H-2.54FFKDSA1/V-5.08FFKDSA1/H-5.08FFKDS/V-3.81FFKDS/H-3.81FFKDSA1/V-6.35FFKDSA1/H-6.35FFKDS/V1-5.08FFKDS/H1-5.08 FFKDSA1/1V-7.62 FFKDSA1/H1-7.62FFKDSA/H1-7.62FFKDSA/V1-7.62ZFKDS1-3.81ZFKDSA1-6.35ZFKDS1.5-5.08ZFKDSA1.5-7.62ZFKKDS1.5-5.08ZFKKDSA1.5-6.08ZFKDS1.5C-5.0ZFKDSA1.5C-6.0ZFKKDS1.5C-5.0ZFKKDSA1.5C-5.0LZFKKDSA1.5C-6.0RZFKDS2.5-5.08ZFKDS2.5-5.08LZFKDSA2.5-6.08RZFKKDS2.5-5.08ZFKKDSA2.5-6.08RZFKKDS2.5-5.08LZFKDS4-7.5ZFKDS4-10ZFKDSA4-9MC1.5/2-ST-3.81 MC1.5/3-ST-3.81 MC1.5/4-ST-3.81MC1.5/5-ST-3.81MC1.5/6-ST-3.81MC1.5/7-ST-3.81MC1.5/8-ST-3.81MC1.5/9-ST-3.81MC1.5/10-ST-3.81MC1.5/11-ST-3.81MC1.5/12-ST-3.81MC1.5/13-ST-3.81MC1.5/14-ST-3.81MC1.5/15-ST-3.81MC1.5/16-ST-3.81MC1.5/2-G-3.81MC1.5/3-G-3.81MC1.5/4-G-3.81MC1.5/5-G-3.81MC1.5/6-G-3.81MC1.5/7-G-3.81MC1.5/8-G-3.81MC1.5/9-G-3.81MC1.5/10-G-3.81MC1.5/11-G-3.81MC1.5/12-G-3.81MC1.5/13-G-3.81MC1.5/14-G-3.81MC1.5/15-G-3.81MC1.5/16-G-3.81MCV1.5/2-G-3.81MCV1.5/3-G-3.81MCV1.5/4-G-3.81MCV1.5/5-G-3.81MCV1.5/6-G-3.81MCV1.5/7-G-3.81MCV1.5/8-G-3.81MCV1.5/9-G-3.81MCV1.5/10-G-3.81MCV1.5/11-G-3.81MCV1.5/12-G-3.81MCV1.5/13-G-3.81MCV1.5/14-G-3.81MCV1.5/15-G-3.81MCV1.5/16-G-3.81MSTB2.5/2-ST-5.08MSTB2.5/3-ST-5.08MSTB2.5/4-ST-5.08MSTB2.5/5-ST-5.08MSTB2.5/6-ST-5.08MSTB2.5/7-ST-5.08MSTB2.5/8-ST-5.08MSTB2.5/9-ST-5.08MSTB2.5/10-ST-5.08MSTB2.5/11-ST-5.08MSTB2.5/12-ST-5.08MSTB2.5/13-ST-5.08MSTB2.5/14-ST-5.08MSTB2.5/15-ST-5.08MSTB2.5/16-ST-5.08 MSTB2.5/17-ST-5.08 MSTB2.5/18-ST-5.08MSTB2.5/19-ST-5.08MSTB2.5/20-ST-5.08MVSTBR2.5/2-ST-5.08MVSTBR2.5/3-ST-5.08MVSTBR2.5/4-ST-5.08MVSTBR2.5/5-ST-5.08MVSTBR2.5/6-ST-5.08MVSTBR2.5/7-ST-5.08MVSTBR2.5/8-ST-5.08MVSTBR2.5/9-ST-5.08MVSTBR2.5/10-ST-5.08MVSTBR2.5/11-ST-5.08MVSTBR2.5/12-ST-5.08MVSTBR2.5/13-ST-5.08MVSTBR2.5/14-ST-5.08MVSTBR2.5/15-ST-5.08MVSTBR2.5/16-ST-5.08MVSTBW2.5/2-ST-5.08MVSTBW2.5/3-ST-5.08MVSTBW2.5/4-ST-5.08MVSTBW2.5/5-ST-5.08 MVSTBW2.5/6-ST-5.08 MVSTBW2.5/7-ST-5.08MVSTBW2.5/8-ST-5.08MVSTBW2.5/9-ST-5.08MVSTBW2.5/10-ST-5.08MVSTBW2.5/11-ST-5.08MVSTBW2.5/12-ST-5.08MVSTBW2.5/13-ST-5.08MVSTBW2.5/14-ST-5.08MVSTBW2.5/15-ST-5.08MVSTBW2.5/16-ST-5.08FKC2.5/2-ST-5.08FKC2.5/3-ST-5.08FKC2.5/4-ST-5.08FKC2.5/5-ST-5.08FKC2.5/6-ST-5.08FKC2.5/7-ST-5.08FKC2.5/8-ST-5.08FKC2.5/9-ST-5.08FKC2.5/10-ST-5.08FKC2.5/11-ST-5.08FKC2.5/12-ST-5.08 FKC2.5/13-ST-5.08 FKC2.5/14-ST-5.08FKC2.5/15-ST-5.08FKC2.5/16-ST-5.08MSTBA2.5/2-G-5.08MSTBA2.5/3-G-5.08MSTBA2.5/4-G-5.08MSTBA2.5/5-G-5.08MSTBA2.5/7-G-5.08MSTBA2.5/8-G-5.08MSTBA2.5/9-G-5.08MSTBA2.5/10-G-5.08MSTBA2.5/11-G-5.08MSTBA2.5/12-G-5.08MSTBA2.5/13-G-5.08MSTBA2.5/14-G-5.08MSTBA2.5/15-G-5.08MSTBA2.5/16-G-5.08MSTBA2.5/17-G-5.08MSTBA2.5/18-G-5.08MSTBA2.5/19-G-5.08MSTBA2.5/20-G-5.08MSTBVA2.5/2-G-5.08MSTBVA2.5/3-G-5.08MSTBVA2.5/4-G-5.08MSTBVA2.5/5-G-5.08MSTBVA2.5/6-G-5.08MSTBVA2.5/7-G-5.08MSTBVA2.5/8-G-5.08MSTBVA2.5/9-G-5.08MSTBVA2.5/10-G-5.08MSTBVA2.5/11-G-5.08MSTBVA2.5/12-G-5.08MSTBVA2.5/13-G-5.08MSTBVA2.5/14-G-5.08MSTBVA2.5/15-G-5.08MSTBVA2.5/16-G-5.08MSTBVA2.5/17-G-5.08MSTBVA2.5/18-G-5.08MSTBVA2.5/19-G-5.08MSTBVA2.5/20-G-5.08GMSTB2.5/2-ST-7.62 GMSTB2.5/3-ST-7.62 GMSTB2.5/4-ST-7.62GMSTB2.5/5-ST-7.62GMSTB2.5/7-ST-7.62GMSTB2.5/8-ST-7.62GMSTB2.5/9-ST-7.62GMSTB2.5/10-ST-7.62GMSTB2.5/11-ST-7.62GMSTB2.5/12-ST-7.62GMSTBA2.5/2-G-7.62GMSTBA2.5/3-G-7.62GMSTBA2.5/4-G-7.62GMSTBA2.5/5-G-7.62GMSTBA2.5/6-G-7.62GMSTBA2.5/7-G-7.62 GMSTBA2.5/8-G-7.62 GMSTBA2.5/9-G-7.62GMSTBA2.5/10-G-7.62GMSTBA2.5/11-G-7.62GMSTBA2.5/12-G-7.62GMSTBVA2.5/2-G-7.62GMSTBVA2.5/3-G-7.62GMSTBVA2.5/4-G-7.62GMSTBVA2.5/5-G-7.62GMSTBVA2.5/6-G-7.62GMSTBVA2.5/7-G-7.62GMSTBVA2.5/8-G-7.62GMSTBVA2.5/9-G-7.62GMSTBVA2.5/10-G-7.62GMSTBVA2.5/11-G-7.62GMSTBVA2.5/12-G-7.62CR-MSTBCP-MSTBSK U/2.8 WH:UNBEDRUCKTSK U/3.8 WH:UNBEDRUCKTSK 5/3.8:UNBEDRUCKTSK 5.08/3.8:UNBEDRUCKTME12.5UT GNME12.5OT-MSTBO SETME12.5OT-MKDSO SETME17.5UT GNME17.5OT-MSTBO SETME17.5OT-MKDSO SETME22.5UT GNME22.5OT-MSTBO SETME22.5OT-MKDSO SETUM72-PROFIL 200CMUM72-SEUM72-SEFE/LUM72-SEFE/RUM72-FEHC-B 6-EBUSHC-B 6-ESTSHC-B 10-EBUSHC-B 10-ESTSHC-B 16-EBUSHC-B 16-ESTSHC-B 24-EBUSHC-B 24-ESTSHC-B 6-TFL-43/M1PG13.5SHC-B 6-AMLHC-B 10-TFQ-52/M1PG16SHC-B 10-AMQHC B 16-TFQ-76/M1PG21SHC-B 16-AMQHC-B 24-AMQHC-B 24-TFQ-76/M1PG21SHC-B 48-TFL-96/M1PG29SHC-B 48-AML HC-B 32-TFQ-80/M1PG29S HC-B 32-AMQHC-D 25-EBUCHC-D 25-ESTCHC-D 40-EBUCHC-D 40-ESTCHC-A 10-ESTSHC-A 10-EBUSHC-A 3-ESTSHC-A 3-EBUSHC-A 4-EBUSHC-A 4-ESTSHC-D 7-AML-24/GR ALUHC-D 7-TFL-48/M1PG11G ALUHC-D 15-TFL-66/M1PG16SHC-D 15-AMLHC-D 25-TFL-72/M1PG16SHC-D 25-AMLHC-D 50-TFQ-76/M1PG29SHC-D 50-AMQHC-A 16-EBUSHC-A 16-ESTS CK1.6-ED-0.75ST AG CK1.6-ED-1.00ST AGCK1.6-ED-1.50ST AGCK1.6-ED-0.75BU AGCK1.6-ED-1.00BU AGCK1.6-ED-1.50BU AGSACB-4/4-L-CSACB-4/8-L-CSACB-8/8-L-CSACB-8/16-L-CSACB-4/4-CSACB-4/8-CSACB-8/8-CSACB-8/16-CSACB-4/4-L-C-90SACB-4/8-L-C-90SACB-8/8-L-C-90SACB-8/16-L-C-90SACB-4/4-C 90SACB-4/8-C 90SACB-8/8-C 90SACB-8/16-C 90SACB-4/8-5.0PURSACB-4/8-10.0PURSACB-8/16-5.0PURSACB-4/4-5.0PURSACB-4/4-10.0PURSACB-8/8-5.0PUR SACB-8/8-10.0PUR SACB-4/4-L-5.0PURSACB-4/4-L-10.0PURSACB-4/8-L-5.0PURSACB-4/8-L-10.0PURSACB-8/8-L-5.0PURSACB-8/8-L-10.0PURSACB-8/16-L-5.0PURSACB-8/16-L-10.0PURSACB-4/4-L-SCSACB-8/8-L-SCSACB-4/8-L-SCSACB-8/16-L-SCSACB-4/4-SCSACB-8/8-SCSACB-4/8-SC SACB-8/16-SCSACB-4Q/4P-5.0PURSACB-4Q/4P-10.0PURSACB-8Q/4P-5.0PURSACB-8Q/4P-10.0PURSACB-4Q/4P-L-5.0PURSACB-4Q/4P-L-10.0PURSACB-8Q/4P-L-5.0PURSACB-8Q/4P-L-10.0PURSACB-4Q/4P-L-SCSACB-8Q/4P-L-SCSACB-4Q/4P-SCSACB-8Q/4P-SCSACB-4/4-L-M23SACB-4/8-L-M23SACB-8/8-L-M23SACB-8/16-L-M23 SACB-4/4-L-M23 180 SACB-4/8-L-M23 180SACB-8/8-L-M23 180SACB-4/4-M23 180SACB-4/8-M23 180SACB-8/8-M23 180SACB-8/16-M23 180SACB-4/4-M23 SACB-4/8-M23 SACB-8/8-M23SACB-8/16-M23SAC-3P-M12MS/1.5-PURSAC-3P-M12MS/3.0-PURSAC-3P-M12MS/5.0-PURSAC-3P-M12MR/1.5-PURSAC-3P-M12MR/3.0-PURSAC-3P-M12MR/5.0-PURSAC-3P-M12MS/1.5-PUR/M 8FS SAC-3P-M12MS/3.0-PUR/M 8FS SAC-3P-M12MS/1.5-PUR/M 8FR SAC-3P-M12MS/3.0-PUR/M 8FR SAC-3P-M12MR/1.5-PUR/M 8FS SAC-3P-M12MR/3.0-PUR/M 8FS SAC-3P-M12MR/1.5-PUR/M 8FR SAC-3P-M12MR/3.0-PUR/M 8FR SAC-3PQ-1.5-PUR/M 8FSSAC-3PQ-3.0-PUR/M 8FS SAC-3PQ-5.0-PUR/M 8FSSAC-3PQ-1.5-PUR/M 8FRSAC-3PQ-3.0-PUR/M 8FRSAC-3PQ-5.0-PUR/M 8FRSAC-3P-M12MS/1.5-PUR/M12FS SAC-3P-M12MS/3.0-PUR/M12FS SAC-3P-M12MS/1.5-PUR/M12FR SAC-3P-M12MS/3.0-PUR/M12FR SAC-3P-1.5-PUR/M12FSSAC-3P-3.0-PUR/M12FSSAC-3P-1.5-PUR/M12FRSAC-3P-3.0-PUR/M12FRSAC-3P-5.0-PUR/M12FRSAC-4P-M12MS/1.5-PURSAC-4P-M12MS/3.0-PURSAC-4P-M12MS/5.0-PURSAC-4P-1.5-PUR/M12FSSAC-4P-3.0-PUR/M12FSSAC-4P-5.0-PUR/M12FSSAC-4P-M12MR/1.5-PURSAC-4P-M12MR/3.0-PURSAC-4P-M12MR/5.0-PURSAC-4P-1.5-PUR/M12FRSAC-4P-3.0-PUR/M12FRSAC-4P-5.0-PUR/M12FRSAC-4P-M12MS/1.5-PUR/M12FS SAC-4P-M12MS/3.0-PUR/M12FS SAC-4P-M12MS/1.5-PUR/M12FR SAC-4P-M12MS/3.0-PUR/M12FR SAC-4P-M12MR/1.5-PUR/M12FS SAC-4P-M12MR/3.0-PUR/M12FS SAC-4P-M12MR/1.5-PUR/M12FR SAC-4P-M12MR/3.0-PUR/M12FR SAC-4P-M12MS/1.5-PUR/M 8FS SAC-4P-M12MS/3.0-PUR/M 8FS SAC-5P-M12MS/1.5-PURSAC-5P-M12MS/3.0-PURSAC-5P-M12MS/5.0-PURSAC-5P-M12MR/1.5-PURSAC-5P-M12MR/3.0-PURSAC-5P-M12MR/5.0-PURSAC-5P-1.5-PUR/M12FSSAC-5P-3.0-PUR/M12FSSAC-5P-5.0-PUR/M12FSSAC-5P-1.5-PUR/M12FRSAC-5P-3.0-PUR/M12FRSAC-5P-5.0-PUR/M12FRSAC-5P-M12MS/1.5-PUR/M12FS SAC-5P-M12MS/3.0-PUR/M12FS SAC-5P-M12MS/1.5-PUR/M12FRSAC-5P-M12MS/3.0-PUR/M12FR SACC-M 8MS-3CON-M-SW SACC-M 8MS-4CON-M-SW SACC-M 8MS-3PCONSACC-M 8MS-4PCONSACC-M12MS-4CON-PG 7-M SACC-M12MS-5CON-PG 7-M SACC-M12MR-5CON-PG 7-M SACC-M12MR-4CON-PG 7-M SACC-M 8MS-3CON-MSACC-M 8MS-4CON-MSACC-M12MS-5CON-PG9-M SACC-M12MR-5CON-PG9-M SACC-M 8MR-3CON-MSACC-M 8FS-3PCONSACC-M 8FS-4PCONSACC-M 8FS-3CON-M-SW SACC-M 8FS-4CON-M-SW SACC-M12FS-5CON-PG 7-M SACC-M12FR-5CON-PG 7-M SACC-M12FS-4CON-PG 7-M SACC-M12FR-4CON-PG 7-M SACC-M 8FS-3CON-MSACC-M 8FS-4CON-MSACC-M12FS-5CON-PG9-M SACC-M12FR-5CON-PG9-M SACC-DSIV-M12MS-5CON-L180 SACC-DSIV-M12MS-5CON-L90 SACC-DSIV-M12FS-5CON-L180 SACC-DSIV-M12FS-5CON-L90 SACC-DSI-M12MS-5CON-L180 SACC-DSI-M8MS-3CON-L180 SACC-DSI-M8MS-4CON-L180 SACC-DSI-M12FS-5CON-L180 SACC-DSI-M8FS-3CON-L180 SACC-DSI-M8FS-4CON-L180 SAC-3P-5.0-PUR/M 8FSSAC-3P-5.0-PUR/M 8FRSAC-3P-1.5-PUR/M 8FSSAC-3P-3.0-PUR/M 8FSSAC-3P-1.5-PUR/M 8FRSAC-3P-3.0-PUR/M 8FRSAC-3P-M 8MS/1.5-PURSAC-3P-M 8MS/3.0-PURSAC-3P-M 8MS/5.0-PURSAC-3P-M 8MR/1.5-PURSAC-3P-M 8MR/3.0-PURSAC-3P-M 8MR/5.0-PURSAC-3P-M 8MS/1.5-PUR/M 8FS SAC-3P-M 8MS/3.0-PUR/M 8FS SAC-3P-M 8MS/1.5-PUR/M 8FR SAC-3P-M 8MS/3.0-PUR/M 8FR SAC-3P-M 8MS/1.5-PUR/M 12FS SAC-3P-M 8MS/3.0-PUR/M 12FS SAC-3P-M 8MS/1.5-PUR/M 12FR SAC-3P-M 8MS/3.0-PUR/M 12FR SAC-4P-M 8MS/1.5-PURSAC-4P-M 8MS/3.0-PURSAC-4P-M 8MS/5.0-PURSAC-4P-M 8MR/1.5-PURSAC-4P-M 8MR/3.0-PURSAC-4P-M 8MR/5.0-PURSAC-4P-1.5-PUR/M 8FSSAC-4P-3.0-PUR/M 8FSSAC-4P-5.0-PUR/M 8FSSAC-4P-1.5-PUR/M 8FRSAC-4P-3.0-PUR/M 8FRSAC-4P-5.0-PUR/M 8FRRCK-TGUM/BL12/5.0PUR-URCK-TGUM/BL12/10.0PUR-U RCK-TWUM/BL12/5.0PUR-URCK-TWUM/BL12/10.0PUR-U RCK-TGUM/BL16+3/5.0PUR-U RCK-TGUM/BL16+3/10.0PUR-U。
EEM101-单相计量模块说明书
输出
5
P1
输 入 / 用户可编程 IO 口.推荐：不使用时悬空
输出
6
P2
输 入 / 用户可编程 IO 口.推荐：不使用时悬空
输出
7
P3
输 入 / 用户可编程 IO 口.推荐：不使用时悬空
输出
8
RX0
9
TX0
10
RD
11
RX1
12
TX1
13
VN
14
VL
15
I-
16
I+
17VDD18 NhomakorabeaGND
19，20，21， NC 22，23,24
输 入 / 用户可编程 IO 口.推荐：不使用时悬空 输出
输 入 / 用户可编程 IO 口.推荐：不使用时悬空 输出
输出
用户采用 485 通信时配合 UART 使用，485 通信发送接收 选择端口。推荐：使用 485 通信连接时使用此引脚
输入
UART 通信接收数据引脚，TTL 电平接口。可直接和用户 单片机 UART 连接。
输入
电流通道负极电流信号输入端，端口 Imax 120MA.推荐电 路：使用 5（6）/2.5ma 变比的互感器
输入
电流通道正极电流信号输入端，端口 Imax 120MA.推荐电 路：使用 5（6）/2.5ma 变比的互感器
输出
模块工作电源输出引脚。工作电压：5V 该引脚可接 10UF/16V 电容并联 100NF/16V 瓷介电容进行去耦
2 电源电路设计
电源电路设计采用 LDO 方式进行稳压设计，采用二极管 M7 保护电源接饭，电解电采用推 荐型号，推荐如下图所示：
电源设计电路
3 25V/22UF C V485 485GND 0 1 8 B A V 5 5 0 8 8 路 4 4 +Vo 电 压 稳 D 非 N C A 离 G N Vin 4 C U 隔 ZY1205FKD-1W U T P D D P6KE6.8CA TVS2 1 7 4 N N 1 G G D VCC IA- IA+ N G 2 VCC12 VCC50 25V/22UF C D N 3 4 5 6 7 8 9 0 1 2 3 4 G 1 1 1 1 1 1 1 2 2 2 2 2 V485 - + L C C C C C C I N D 485GND I V N N N N N N V N 485COMM-2 VCC 5 7 6 8 G 板 3 心 B A D 核 N VCC G 相 5 T D D 485GND 0 单 8 N D U D 3 2 1 0 7 2 E TX1 RX1 R TX0 RX0 P P P P VBAT G V O 3 2 VCC60 25V/22UF C D D /RE R D U SIGERPHAS U D D N N N G Nonpolarity-485 2 1 0 9 8 7 6 5 4 3 2 1 G G 2 1 1 1 4 3 2 1 k N 9 0 I 1 1 R U VCC60 1 3 D N G V485 V485 1 25V/22UF C T TXD4852 RXD4852 CON4852 U D O N D G D VCC12 N 0 0 N 8 7 1 1 G 5 R 5 R G 2 V485 6 理 N I 0 1 8 处 7 U 源 7 1 电 1 M M 485GND 1 D 25V/22UF C D D NEC2501 NEC2501 V N A NEC2501 G U VCC12 理 - + I I T 处 CT-2 C 源 7 1 OP6 OP4 OP5 电 M M 2 1 0 M 1 1 5 1 R 0 0 6 5 4 1 1 R 5 R 5 R VCC24 IA- IA+ RXD4852 L CON4852 TXD4852 V VCC VCC VCC
蜂鸟工业自动化-蜂鸟Herculine 2000系列电动阀门驱动器规格表说明书
Honeywell Process Control, 512 Virginia Drive, Fort Washington, PA 19034Printed in U.S.A. ν © Copyright 2006-2008 — HoneywellHerculine ® 2000 Series Actuators61-86-03-14June 08Page 1 of 14SpecificationOverviewHoneywell’s HercuLine ® 2000 seriesactuators are low torque, precision electric actuators incorporating all of the easy-to-use, high quality, and reliable features of the traditional HercuLine ® actuators. Ensuring processes operate at maximum efficiency, with minimal downtime, and lowest lifetime cost requires precision and high reliability Herculine ®actuators. They are industrial rated and engineered for very precise positioning of dampers and valves. They perform especially well in extremely demanding environmentsrequiring continuous duty, high reliability, and low maintenance. HercuLine ® 2000 actuators are used inon/off power to open/close or positionproportional with 135 or 1000 ohmfeedback applications.HercuLine ® 2001 and 2002 Smart actuators are used in current proportional or digital control applications. Access to all actuator parameters for real-time business and maintenance decisions isstandard through Modbus RTU, localdisplay, or via HercuLink ® Palm PDAsoftware.HercuLine ® 2002 actuators have additional standard features such as non-contact position sensing and slidewire emulation output. HercuLink ® software enables calibration, configuration, and access to maintenance data using your Palm PDA.Smart Features – HercuLine ® 2001 & 2002 RS485/Modbus RTU Communication -Modbus RTU communication is standard allowing seamless networking of Honeywell control productsAlarm Functions – Alarms may be assigned to relay outputs or may be accessed through the Modbus network. Alarms can be triggered from stall,temperature limits, motor cycle count, out of automatic mode, digital input, position, input failure, position sensor failure,power up failure, and more. Characterization – Programmable linear, equal percentage, quick opening, or user configured 20-point characterizationFailsafe – the actuator can beprogrammed to drive open, closed, remain in-place, or drive to a userspecified position on loss of input signal or position sensor.Split range operation –programmable and infinitely adjustable.Factory Calibration – stored in non-volatile memory and can be restored at any time.Digital Input Override – A digital input is provided that can be programmed to drive the actuator open, closed, remain in-place, or to a user specified position oncontact closure for emergency situations. Health Monitoring – A standard feature on all HercuLine ® Smart actuators accumulates information about actuatoroperation. The information then can be used to evaluate and determine predicted or scheduled maintenance periods. Parameters monitored are accumulated stall time, exceeded thermal operatingrating of the actuator, and number of motor starts in a region of travel, total travel and current actuator travel.Input Filter Setting – Fourprogrammable combinations - none,spike, low pass, or spike + low pass filter.Configuration security – Passwordprotection is provided to prevent tampering, allowing users to lock out some, all, or no groups of setup parameters. Direction of rotation – programmable. Input Signals – 0/4 to 20 mA, 0/1 to 5 Vdc, 0 to 10 Vdc, Digital RS485 Modbus RTU protocol, or Series 90 control. Output Signals – 0/4 to 20 mA, 0/1 to 5 Vdc or slidewire emulation. Accurate Positioning – Motor/gear train provides accurate positioning with almost instantaneous start/stop characteristics. Stall Alarm – provides alarm output in theevent of actuator stall due to overload. Smart OptionsHercuLink ® Software – loaded onto theusers Palm PDA, laptop PC or desktop computer. This software allows you to configure or calibrate the actuator. Inaddition, maintenance information may be read, stored and later loaded in CSV format to the user’s computer for maintenance tracking.Hart ™ Communication – For HART user’s optional HART communications provides access to calibration,configuration, and maintenance data. In addition, the HART communicationsoption is structured to work with the HART Asset Management Features.Local HMI Configuration – Optional keypad and high intensity display isavailable (Figure 1). The display may be rotated in 90° increments for actuator mounting orientations other than horizontal.Non-contact position sensing (NCS) – Herculine ® 2002 only. See description next page.Slidewire Emulation (SEC) – Herculine ®2001 and 2002 only. See text next page.Auxiliary Relay Outputs –Programmable relay outputs can be used in place of auxiliary switch outputs to provideadditional functionality such as indication of alarm status, control of other equipment, or to indicate position. Battery Powered 232/485 converter and cable – used to connect the Palm PDA to the HercuLine ® actuator for communication.61-86-03-14 Page 2Non-Contact Position SensingAvailable in the HercuLine ®2002actuator. The technology is a variableinductance, non-contact position sensor mounted directly to the actuator outputshaft providing precision position sensing from 0 to 150 degrees (Figure 3). Thistechnology eliminates maintenance item such as wipers, bearings, as well asstatic friction, hysteresis and electricalnoise over a wide range of demandingenvironmental conditions. Typically use in very demanding applicati s dons wheredowntime is not an option.Slidewire EmulationAvailable in the HercuLine ® 2001/2002 actuator. The Slidewire EmulationCircuit (SEC) emulates the proportiona voltage output of a typical slidewire through a high impedance circuit. Th voltage output is proportional to the supply voltage and shaft position. If ordered on the 2002 model, a non-contact position sensor is used todetermine shaft position in place o slidewire. Typically used in very demanding applications wher l e f the e downtime is not an option.Potentiometer SensingAn advanced high cycle filmpotentiometer for position sensing for true position feedback is available as option on the Herculine an ndard on Herculine ®2001 EEU model.® 2000 BMUmodel and sta Self-locking/releasingGear TrainThe worm gear output combination is self-locking and self-releasing and maintains position upon loss of power. It is designed to hold greater than two times the rated output torque in a back-driving condition. This design provides superior reliability without themaintenance associated with other self-locking and brake mechanisms. General Features • e thout • ycle – Continuous duty•y out degrading •Hz, single phase <Motor - no burn out motor can b stalled up to 100 hours wi damage to the actuator.Duty C cycle Any position mounting – the actuator may be mounted in an orientation with performance.Power Requirements – Low power consumption 120/240 Vac, 50/60 0.6/0.3 Amp.•X industrial •-•culine ® 2000 series •ification – CSA (pending), UL, CE Enclosure – Rugged, Die cast aluminum NEMA 4grade enclosure.Low Maintenance – Simple proven design means high reliability/low maintenance. Limit Switches – Two end-of-travel electric limit switches are supplied as standard equipment with all Her actuators.• Warranty – Exceptional warranty CertGeneral Options•r PDT switches are •tuator when power is • vailable •s to r ndis & Staefa) •or valve or damper connection.Auxiliary Switches – up to fou additional S available.Manual Operation – a manual hand wheel is optional and used to operate the ac not available.Auto-Manual – electric hand switch with auxiliary contacts indicating an "Out-of-Auto" position is a for local electric control.Competitive Mounting Plates – to adapt the HercuLine ® actuator Invensys (Barber-Colman) o Siemens (La mountings.Linkage assemblies – Pushrod assemblies f61-86-03-14Page 3Optional Local Display and Keypad for HercuLine ® 2001 and 2002A local display and keypad is optional for configuration and set-up (Figure 2). A high intensity 10-character LED display and simple push buttons provide quick access for actuator set up and status information. If relay outputs are specified, all configuration can be done through either the local HMI interface or the HercuLink ® configurator. HercuLink ® Palm PDA software or HART ™ communications is available for those ordering units without the display and keypad.Lower Control Arm RotationPushbuttons (Fou (Six Cha to Access Set Up, Status Calibration Para meters.Figure 1 Local HMI (Display and Keypad)61-86-03-14 Page 4Non-Contact Sensor NCS Spoiler (shown at full150 degree travel CCW)NCS PWA NCS setscrewRelay PWA card guides (relay PWAs removed)Figure 2 Non-Contact Sensor Assembly (HercuLine® 2002)61-86-03-14Page 5HercuLink® Computer InterfaceHercuLink® Computer software enables access to programming and communication functions available as standard with the HercuLine® 2001 and 2002 actuators without the added expense of the keypad & display HMI. Using a Palm™ PDA, laptop PC or desktop computer, HercuLink® software, and a RS232/485 converter users may configure, calibrate, and access maintenance information locally or remotely to the actuator.Using HercuLink® software the computer may be used as a master device over a Modbus network to access information to/from the actuators and to control the device. Set-up configurations may also be stored on the computer for download to other HercuLine®devices. Information may be stored on the users PC in CSV format for use in preventative maintenance programs.•Certified on Palm™ m125, m130, and m505.•Compatible with Palm OS3.5 or higher.•Compatible with Windows 2000 or XP operating systems•Minimum system requirements:•Windows 2000 (w/service pack 2), Windows NT (w/service pack 5), Windows ME, Windows XP•200 MHz Pentium with 64 Megs RamPalm™ is a trademark of Palm, Inc.HotSync® is a registered trademark of Palm Computing, Inc.HercuLink® is a trademark of HoneywellFigure 3 PDA connection61-86-03-14Page 6Set Up/Configuration Parameters for Keypad & Display or HercuLink® SoftwareConfiguration parameters are logically grouped and accessed using the local HMI. Actuator calibration is also accomplished through a simple procedure using the keypad. By pressing the SETUP button on the HMI, you can step through the set up groups that contain all of the configuration parameters. The table below summarizes the configuration parameters available within the various set up groups. Full details of all configuration parameters are found in the HercuLine® 2000 Series Actuator Installation, Operation and Maintenance Manual, document number 62-86-25-10.Set Up Group Configuration Parameter Selections/SettingsSET INPUT⎯Selects various parameters that define actuator operation.IN TYP – Input Actuation TypeINP HI – Input High Range ValueINP LO – Input Low Range ValueFILTYP – Input Filter TypeLPFILT – Low Pass Filter Time ConstantDirect – Actuator RotationDband – Input DeadbandFSFTYPH – FailsafeHI TypeFsFVALH – FailsafeHI ValueFSFTYPL – FailsafeLO TypeFsFVALL – FailsafeLO ValueCHAR – Input Characterization TypeCUST – Custom Characterization TypeSET RELAY⎯When the actuator is equipped with optional relays, this set up group allows you to set relay action for various actuator operating conditions. Contact closure can be wired to external annunciators or alarm points to indicate conditions for any of the Relay Types. RTYPnn – Relay TypeInput RangePosition RangeDeviationUpper or Lower Limit TravelTemperature High or LowCycle CountMotor StalledManual ModePower Up Test FailureInput Signal FailurePosition Sensor Signal FailureDigital Input ClosureTotal Degrees TraveledRnnVAL – Relay ValueRnn HL – Relay High/LowRLYnHY – Relay HysteresisSET CUROUT⎯Selects the current (or voltage) output range of the actuator.CUROUT - Output Signal Range4 – 20 mA 0 – 20 mA1 – 5 V 0 – 5 VOr SWESET COMM⎯Actuator can be defined as a master or slave device on a Modbus RTU RS-485 loop. Operating setpoint can be transmitted to the actuator and operating status can be read when connected to supervisory control M – Communications Parameters ADDRES – Device AddressBAUD – Baud RateXmtDLY – Response DelayDBLBYT – Floating Point Data FormatSET DIGINP⎯Selects digital input action upon contact closure. DIGINP – Digital Input State Endpos – End Position ValueSET DISPLA⎯Selects desired decimal places and engineering units for local display DECMAL – Decimal Point Location EUNITS – Units DisplayUNITS – Display UnitsCAL INPUT, MTR, CURENT⎯If needed, field calibration of the actuator input, motor position and actuator output can be performed using the local keypad and display.61-86-03-14Page 7 Set Up Group Configuration Parameter Selections/SettingsSET LOCK⎯Enables lock out or access to selected set up group parameters and calibration values.LOCKID – Set Security Password LOCK – Lock OutMAENAB – Mode button lockoutREAD STATUS⎯Displays failsafe condition and the results of various diagnostics performed during power up.FAILSF – FailsafeRAMTST – RAM Test DiagnosticSEETST – Serial EEPROM TestDiagnosticCFGTST – Configuration Test DiagnosticCALTST – Calibration Test DiagnosticSET DRVINF⎯Allows access to actuator device information.VERSON – Firmware VersionSPEED – Stroke SpeedPOWER – Power Input Voltage and LineFrequencyTAG – Tag NameDMFG – Manufacturing DateLREP – Date of Last RepairLCAL – Date of Last Field CalibrationREPTYP – Repair TypeSET MAINT⎯Allows access to parameters that monitor operating conditions.TEMP – Actuator TemperatureTEMPHI – High Temperature LimitTEMPLO – Low Temperature LimitACSTA – Accumulated Stall TimeSTARTS – Accumulated Motor StartsRLnCNTS – Relay Cycle CountsREGNn – Accumulated Motor StartsTOTDEG – Total degrees traveledMANRST – Reset Maintenance StatisticsLD CAL – Restore CalibrationLD CFG – Restore ConfigurationSYSRST – System RestartSpecifications – GeneralPhysicalWeight 2000: 25 lb. (11.36 kg)2001,2002: 27 lbs. (12.27 kg)Enclosure Precision-machined die cast aluminum housing, finished in light gray powder coat epoxy. Gear Train Alloy steel, high efficiency steel spur gear primary train. Precision ground, self-locking/selfreleasing worm gear final mesh.Mechanical Stops Factory set at 90° or 150° (+/-5°).Storage Temperature –40 °C to +93 °C (–40 °C to +200 °F)Relative Humidity 0 % to 99 % R.H. non-condensing over the full operating temperature range.Scale 0 % to 100 % corresponding to full crank arm travel.Crank Arm Adjustable radii 1.0 in (25.4mm) to a maximum of 2.8 in (71.1mm). Position adjustablethrough 360° rotation.Output Shaft 0.625+/-.005 in (15.88 +/-.13mm) diameter (round)Rotation 90° or 150° degrees between 0 % and 100 % on scale, limited by mechanical stops. Manual Hand wheel(option)Provides a means of positioning the actuator in the event of a power failure or set-up. Lubrication Texaco Starplex 2 EP GreaseOutput Torque/Full Travel Stroking Time Torque lb-in (N M)50 / (6.0)100 / (11.5)200 / (22.5)400 / (45.0)400 / (45.0)50 Hz (90°/150°)4.5 / 7.59 / 1518 / 3036 / 6054 / 9060 Hz (90°/150°)4 / 67 / 1215/2530/5045/7561-86-03-14Page 8ElectricalMains Supply 100-130 Vac single phase, 50 Hz or 60 Hz200-240 Vac single phase, 50 Hz or 60 HzMotor Instant start/stop, non-coasting, non-burnout, continuous duty, permanent magnet,synchronous induction motor. Can be stalled up to 100 hours without damage.Motor Current = No load = full load = locked rotor = 0.4 amp for 120Vac, 0.2 amp for 240 VacLoss of Power Stays in place on loss of powerLocal Auto/Manual Switch Optional – Allows local and automatic operation of the actuator.End of travel Limit Switches Standard – adjustable to limit actuator travel to less than 90 or 150 degrees respectively Auxiliary Switches/Relays Optional – Up to 4 additional SPDT switches rated at (10 A at 125 Vac, 5 A at 250 Vac). CertificationsApprovals CSA/UL (Standard)CE Compliant (optional)Enclosure Rating Type 4 (NEMA 4), IP66 (standard)Torque Settings of Crank Arm BoltsClamp Bolt 88 lb-in (10 N-m)Electrical and Performance SpecificationsHercuLine® 2000 SeriesHercuLine® 2002 HercuLine® 2001 Herculine® 2000Input Signals Analog:•0/4 to 20 mA (With CPUPWA jumper in currentposition)•0/1 to 5 Vdc•0 to 10 VdcDigital:•Modbus RTU (RS485) Analog:•0/4 to 20 mA (With CPUPWA jumper in currentposition)•0/1 to 5 Vdc•0 to 10 Vdc•Series 90 controlDigital:•Modbus RTU (RS485)120 Vac drive open/120 Vacdrive close240 Vac drive open/240 Vacdrive closeIsolation Input signal, output signal and power are isolated from eachother.NA Load Requirement (4-20) Current Out — 0 to 1000 ohms NAInput Impedance 0/4 to 20 mA0/1 to 5 Vdc0-10 Vdc 250 ohms10 K ohmsNA0 to 20 mA, 4 to 20 mA0 to 5 Vdc & 1 to 5 Vdc with 250 ohm resistor, (0 to 16 Vdc with 800 ohm resistor) Dual output 1000 ohms over 90 degrees (135 ohms with 158 resistor)Dual output 1000 ohms over 150 degrees (135 ohms with 158 resistor)FeedbackSlidewire emulation - Provides output voltage ratiometric toshaft position and potentiometric to supply voltage(1 Vdc to 18 Vdc) without a slidewire. Emulates a 100 ohm to1000 ohm slidewire. 10 mA output maximum.61-86-03-14Page 9HercuLine® 2002 HercuLine® 2001 Herculine® 2000 Communications Modbus RTU or optional HART™NAOperating Temperature –40°C to +75 °C (–40°F to +170 °F) -40°C to +85 °C (-40°F to+185 °F)Position sensing Non-contact position sensor 1000 ohm film potentiometer Optional dual 1000 ohm filmpotentiometersSensitivity 0.2 % to 5 % of 90° span, proportional to deadband NAHysteresis Less than 0.4 % of full scale NADeadband 0.2 % to 5 % of 90° span, programmable. Shipped at 0.5 %NARepeatability 0.2 % of 90° span NARepositions(minimum @ 90 or 150degree stroke)Table 1 option –050- Table 1 option –100- Table 1 option –200- Table 1 option –400- Table 1 option –600- 160290450700900120250400400400500Voltage/ SupplyStability0.25 % of span with +10/–15 % voltage change NATemperature Coefficient Less than ± 0.030 % of span per degree C for 0 °C to 50 °CLess than ± 0.05 % of span per degree C for –40 °C to 75 °CNAZero Suppression 90 % of span.NA Input Filters Selectable spike and low pass filters.NASolid State Motor Control Two triac switches for clockwise or anti-clockwise motoroperation. Transient voltage protection provided.NAFailsafe operation If input signal exceeds configured input range. Selectable andadjustable.NA Direction of Rotation Field programmable Wire swap Duty Cycle ContinuousProgrammableFunctionsSelectable and configurable operating parameters:NA• Inputrange• Inputfiltering• Inputcharacterization• Security•Digital Input action• Deadband•Failsafe on loss of input signal•Failsafe on loss of position sensor•Direction of rotation•Relay closure action• Communicationparameters•Split range operation• Outputrange• Alarms61-86-03-14Page 10Actuator Crank ArmThe HercuLine® 2000 Series Actuators come standard with a 2.8 inch (71.12mm) crank arm (Figure 4). The crank arm uses linkage kits (above). Adjustable radius (1.0 in (25.4mm) to 2.80 in (71.12mm)). Position adjustable through 360° rotation.Figure 4 Standard 2.8” (71.12mm) Crank ArmFigure 5 Crank Arm with optional ball joint and push rodModel Selection GuidecontinuedOutline Dimension DrawingsmminchesActionator M640A, M740A, and M940A replacementSee Honeywell SalesNet at /salesnet/supporting_docs/sales_tools/actionator_to_hl_xover.xlsWarranty/RemedyHoneywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Contact your local sales office for warranty information. If warranted goods are returned to Honeywell during the period ofcoverage, Honeywell will repair or replace without charge those items it finds defective. The foregoing is Buyer's sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability andfitness for a particular purpose. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use.While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application.For more information, contact Honeywell sales at (800) 343-0228.Honeywell Process ControlHoneywell512 Virginia DriveFort Washington, PA 1903461-86-03-14 June 08 Printed in USA /ps。
单相智能电能表说明书范文
目录一、产品简介....................................................................................................................... 错误!未定义书签。
1.1 概述....................................................................................................................... 错误!未定义书签。
1.2 规格和主要参数................................................................................................... 错误!未定义书签。
二、外形说明及安装........................................................................................................... 错误!未定义书签。
2.1 液晶显示及内容................................................................................................. 错误!未定义书签。
2.2 电表的安装及接线............................................................................................. 错误!未定义书签。
三、功能说明....................................................................................................................... 错误!未定义书签。
菲森 F200 F210 数字口内影像板扫描处理系统 使用说明书
使用说明书F200/F210数字口内影像板扫描处理系统声明本说明书为操作、保养和维修产品的参考资料。
用户应严格依照说明书内容操作，对于不按照说明书内容操作而造成的故障或事故，深圳市菲森科技有限公司（以下简称“菲森公司”）不负担任何法律责任。
菲森公司拥有本说明书中所有内容的版权，未经本公司的明确书面许可，任何人不得照相复制、复印或翻译成其它语言。
本产品说明书包含受版权法保护的专有资料，包括但不限于技术秘密、专利信息等商业秘密，用户具有保密义务，不得向无关第三方披露本说明书中的任何内容。
用户持有本产品说明书并不表示菲森公司对产品所含知识产权的授权许可。
本说明书的修改权、更新权及最终解释权均属于菲森公司。
产品注册信息产品名称：数字口内影像板扫描处理系统产品型号：F200/F210注册人/生产企业：深圳市菲森科技有限公司医疗器械生产企业许可证编号：粤食药监械生产许20081648号产品注册证号：粤械注准20172310737注册地址：深圳市南山区桃源街道同富裕工业城3号厂房1楼生产地址：深圳市南山区桃源街道同富裕工业城3号厂房1楼生产日期：详见标签说明书编写日期：2018年9月产品使用年限本产品使用寿命为5年。
制造商的责任菲森公司仅在下列情况下才认为应对仪器的安全性、可靠性和性能负责，即：装配操作、扩充、重调、改进和维修均由菲森公司认可的人员进行，相应房间的电气安装环境符合国家标准，以及仪器按照操作指导进行使用。
菲森公司将在您提出要求时有偿提供电路图及其它信息，以帮助适当的、合格的技术人员来维修那些菲森公司归类为可由用户维修的仪器部分。
前言本说明书主要介绍数字口内影像板扫描处理系统的功能和操作方法。
说明书适用对象本说明书适用于临床专业人员和其他授权用户。
图例和命名本说明书中提供的所有图例仅用于举例说明。
本说明书的术语说明警告：针对可能造成人员伤亡的操作或情形。
小心：针对可能造成设备损坏，产生错误数据，或使过程失效的操作或情形。
MEMORY存储芯片LPC824M201JHI33E中文规格书
1.General descriptionThe LPC82x are an ARM Cortex-M0+ based, low-cost 32-bit MCU family operating atCPU frequencies of up to 30MHz. The LPC82x support up to 32 KB of flash memory and8KB of SRAM.The peripheral complement of the LPC82x includes a CRC engine, four I2C-businterfaces, up to three USARTs, up to two SPI interfaces, one multi-rate timer,self-wake-up timer, and state-configurable timer with PWM function (SCTimer/PWM), aDMA, one 12-bit ADC and one analog comparator, function-configurable I/O ports througha switch matrix, an input pattern match engine, and up to 29 general-purpose I/O pins.For additional documentation related to the LPC82x parts, see Section18.2.Features and benefits⏹System:◆ARM Cortex-M0+ processor (revision r0p1), running at frequencies of up to30MHz with single-cycle multiplier and fast single-cycle I/O port.◆ARM Cortex-M0+ built-in Nested Vectored Interrupt Controller (NVIC).◆System tick timer.◆AHB multilayer matrix.◆Serial Wire Debug (SWD) with four break points and two watch points. JTAGboundary scan (BSDL) supported.◆MTB⏹Memory:◆Up to 32KB on-chip flash programming memory with 64 Byte page write anderase. Code Read Protection (CRP) supported.◆8 KB SRAM.⏹ROM API support:◆Boot loader.◆On-chip ROM APIs for ADC, SPI, I2C, USART, power configuration (powerprofiles) and integer divide.◆Flash In-Application Programming (IAP) and In-System Programming (ISP).⏹Digital peripherals:◆High-speed GPIO interface connected to the ARM Cortex-M0+ IO bus with up to 29General-Purpose I/O (GPIO) pins with configurable pull-up/pull-down resistors,programmable open-drain mode, input inverter, and digital filter. GPIO directioncontrol supports independent set/clear/toggle of individual bits.◆High-current source output driver (20 mA) on four pins.◆High-current sink driver (20 mA) on two true open-drain pins.◆GPIO interrupt generation capability with boolean pattern-matching feature on eightGPIO inputs.◆Switch matrix for flexible configuration of each I/O pin function.◆CRC engine.◆DMA with 18 channels and 9 trigger inputs.⏹Timers:◆State Configurable Timer (SCTimer/PWM) with input and output functions(including capture and match) for timing and PWM applications. EachSCTimer/PWM input is multiplexed to allow selecting from several input sourcessuch as pins, ADC interrupt, or comparator output.◆Four channel Multi-Rate Timer (MRT) for repetitive interrupt generation at up tofour programmable, fixed rates.◆Self-Wake-up Timer (WKT) clocked from either the IRC, a low-power,low-frequency internal oscillator, or an external clock input in the always-on power domain.◆Windowed Watchdog timer (WWDT).⏹Analog peripherals:◆One 12-bit ADC with up to 12 input channels with multiple internal and externaltrigger inputs and with sample rates of up to 1.2 Msamples/s. The ADC supports two independent conversion sequences.◆Comparator with four input pins and external or internal reference voltage.⏹Serial peripherals:◆Three USART interfaces with pin functions assigned through the switch matrix andone common fractional baud rate generator.◆Two SPI controllers with pin functions assigned through the switch matrix.◆Four I2C-bus interfaces. One I2C supports Fast-mode Plus with 1Mbit/s data rateson two true open-drain pins and listen mode. Three I2Cs support data rates up to 400 kbit/s on standard digital pins.⏹Clock generation:◆12MHz internal RC oscillator trimmed to 1.5 % accuracy that can optionally beused as a system clock.◆Crystal oscillator with an operating range of 1MHz to 25MHz.◆Programmable watchdog oscillator with a frequency range of 9.4 kHz to 2.3MHz.◆PLL allows CPU operation up to the maximum CPU rate without the need for ahigh-frequency crystal. May be run from the system oscillator, the external clockinput, or the internal RC oscillator.◆Clock output function with divider that can reflect all internal clock sources.⏹Power control:◆Power consumption in active mode as low as 90 uA/MHz in low-current modeusing the IRC as the clock source.◆Integrated PMU (Power Management Unit) to minimize power consumption.◆Reduced power modes: Sleep mode, Deep-sleep mode, Power-down mode, andDeep power-down mode.◆Wake-up from Deep-sleep and Power-down modes on activity on USART, SPI, andI2C peripherals.◆Timer-controlled self wake-up from Deep power-down mode.◆Power-On Reset (POR).◆Brownout detect (BOD).⏹Unique device serial number for identification.⏹Single power supply (1.8 V to 3.6 V).⏹Operating temperature range -40 °C to +105 °C.⏹Available in a TSSOP20 and HVQFN33 (5x5) package.3.Applications4.Ordering information4.1Ordering options⏹Sensor gateways ⏹Simple motor control ⏹Industrial⏹Portables and wearables ⏹Gaming controllers ⏹Lighting⏹8/16-bit applications ⏹Motor control⏹Consumer⏹Fire and security applications⏹Climate controlTable 1.Ordering informationType numberPackage NameDescriptionVersionLPC824M201JHI33HVQFN33HVQFN: plastic thermal enhanced very thin quad flat package; no leads; 33 terminals; body 5 ⨯ 5 ⨯ 0.85 mmn/aLPC822M101JHI33HVQFN33HVQFN: plastic thermal enhanced very thin quad flat package; no leads; 33 terminals; body 5 ⨯ 5 ⨯ 0.85 mmn/a LPC824M201JDH20TSSOP20plastic thin shrink small outline package; 20 leads; body width 4.4 mm SOT360-1LPC822M101JDH20TSSOP20plastic thin shrink small outline package; 20 leads; body width 4.4 mmSOT360-1Table 2.Ordering optionsType number Flash/KB SRAM/KB USART I 2C SPI ADCchannels Comparator GPIO Package LPC824M201JHI3332834212Y 29HVQFN33LPC822M101JHI3316434212Y 29HVQFN33LPC824M201JDH203283425Y 16TSSOP20LPC822M101JDH201643425y16TSSOP206.Block diagram7.Pinning information7.1Pinning。
松下电阻焊控制器中文手册
6
名称和功能 3. 名称和功能
3.1 指示灯
()
Panasonic
a. 条件选择指示灯 选择这个模式时亮灯
b. 启动指示灯 条件选择模式下选择启动程序时亮灯
c. 启动序号显示器 表示启动序号（1~4）
d. 焊接条件指示灯 条件选定及程序模式下，选择焊接条件
序号时亮灯 e. 焊接条件序号显示器
表示焊接条件序号（1~9 或者 A~F） f. SOL 指示灯
“严重的人身伤害”指的是失明，烫伤（高 和低度烫伤），电击，骨折和中毒，需要住 院治疗和必要的药物治疗。“轻度的人身伤
害”指烫伤电击等伤害不需要长期的住院治 疗和必要的药物治疗。“财产损失”指对周 围环境和设备的损失。
1.2 必须阅读的安全说明
危险
焊接电源
遵守说明规定防止冒险行事
⑴ 不要将焊接电源用于其它用途。（例如： 管道解冻。） ⑵ 阅读这些说明，安全警告，提醒等非常 重要，否则可能引起重大伤亡事故。 ⑶ 对于驱动电源的输入，要选择好工作位 置，处理方法，储存和接通高压气体，保管 好成品，按照操作说明以及工厂的规定处理 好废品。 ⑷ 防止未经允许的人员进入和在工作区域 周围徘徊。
程序模式下，选择 SOL 序号时亮灯 g. SOL 序号显示
表示 SOL 序号（1 或 2） h. 程序指示灯
选择程序模式下亮灯 i. 数据显示器 A
显示运转时的数据（通电周波、通电角、 打点数及故障序号）及程序监视模式的各 种数据 j. 数据显示器 B 显示运转时的数据（焊接电流、生产数） 及运转时的模式显示、程序监视模式等的 各种数据 k. 监视指示灯 选择监视模式时亮灯 l. 全负载引弧指示 焊接电流已临近界限，不能在上升时亮灯 m. 准备焊接指示灯 当控制器与焊接电源接通时，机器进入运 行状态时亮灯 n．焊接电源指示灯 焊接电源接通时亮灯
Canon佳能单反镜头知识
Canon佳能单反镜头知识-马达作者：疯疯发表在 于2009年07月27日一、佳能的EF自动对焦镜头都内置了两个马达，一个负责自动对焦，另一个负责电磁光圈，佳能自动对焦马达有三大类，弧形马达(ARC FORM DRIVE，简称AFD)，超声波马达(ULTRASONIC MOTOR，简称USM)和微型马达(MICRO MOTOR，简称MM)。
1、弧形马达是佳能EF自动对焦镜头中最早使用的马达，它是一种弧形无刷电机，这样它就可以安放在镜头圆柱壮的镜筒内而不用改变镜筒的形状了，由于其转子小巧的尺寸使得它有非常好的开始/停止反应和控制力，又由于它的无刷设计使得它有很长的使用寿命。
虽然随着高性能的超声波马达和成本更低的微型马达的出现，使用这种马达的镜头在现在已经不多见了，但在某些著名的EF镜头中我们仍然能“看到”它的身影，如EF50mm f/2.5 Compact Macro和EF100-300mm f/5.6 L以及EF135mm f/2.8 Soft Focus柔焦镜头等。
2、超声波马达和传统的马达有很大区别，不管传统的马达有多少种，其原理一般就是将电磁力转变为转动力，而超声波马达的转动力则是产生于超声波振动的能量。
如上所述，超声波马达分环形和微型超声波马达两种。
3、环形超声波马达的定子和转子的直径和镜筒直径相当，可以和镜筒完美的结合。
超声波马达的优点在于：一. 由于其低转速和高扭矩的特性，使得它可以直接驱动镜头而不需要额外的减速机构；二. 定位扭矩大，换句话说就是当马达停下来的时候，镜头就像有刹车那样自动停止对焦；三. 结构非常简单；四. 对启动和停止的控制能力非常好，它可以快速启动，也可以立即停止，而且可以被很精确地控制；五. 操作起来非常安静—几乎无声。
除此之外，佳能的环形超声波马达还有如下特点：六. 其高效率和低能耗的特性使得它可以用相机的电池来供电；七. 环状的马达和镜头镜筒非常合适；八. 低旋转速度非常适合镜头的驱动；九. 旋转速度可以在0.2RPM(五分钟旋转一周)到80RPM(每分钟旋转80周)的大范围内连续无级的调整，所以可以实现对镜头的高精度和高速驱动；十. 可以实现高精度的手控电驱动的调焦，即所谓的全时手动功能；十一. 操作温度范围非常宽，可以在摄氏零下30度到零上60度的温度环境下正常工作，保证了恶劣环境下的稳定操作。
伊顿马达样本
● 97 [ 5.9]
● 120 [ 7.3]
● 146 [ 8.9]
● 159 [ 9.7]
● 185 [11.3]
● 231 [14.1]
● 293 [17.9]
● 370 [22.6]
安装法兰
● 2 螺栓 (标准)，支口直径 82,6 [3.25]，安装孔径 13,59 [.535]，孔分布圆直径 106,2 [4.18] B.C.
hs和t系列马达输出轴密封hs和t系列马达防腐蚀涂层hs和t系列马达速度传感器hs和t系列马达转动轻松的定转子低速阀配流hs和t马达均可供选择h系列s系列t系列技术指标见p8见p14见p20性能参数91115172125尺寸产品安装尺寸输出轴接口121826输出轴的径向载荷能力29输出轴尺寸3031安装尺寸工具3233壳体压力及泄油口3435131927产品号标准的推荐的液压油36其他所有资料请与伊顿公司代理商联系产品目录内容油口尺寸3334373839型号规格编码特殊订货hs和t系列马达带有低速配流阀的技术指标和产品号28轴的转向标准的121826轴的转向与标准相反的373839速度传感器3529303132333435363334282930313233343536333428358通用马达h系列技术指标连续不连续连续不连续最高转速rpm连续流量推荐的过滤精度据iso清洁度1813技术指
● 直径 1 英寸，直轴，月牙键，端部有 1/4-20 的螺纹孔 ● 直径 1 英寸，SAE 6B 花键，端部有 1/4-20 的螺纹孔 ● 直径 1 英寸，直轴，有－ 7,9 [.31] 的垂直通孔，离端面 11,2 [.44] ● 直径 1 英寸，直轴，有－ 10,2 [.40] 的垂直通孔，离轴端 15,7 [.62]，端部还有一个 1/4-20 的螺纹孔 ● 直径 7/8 英寸，SAE B 13 T 花键 ● 直径 7/8 英寸，SAE B 直轴有方键 ● 直径 1 英寸，锥轴，月牙键，带螺母 ● 直径 25mm，直轴，8mm 平键，端部有 M8 x 1,2 螺纹孔 ● 直径 1 英寸，直轴，月牙键，端部 1/4-20 螺纹孔 (有防腐蚀保护层) ● 直径 25mm，直轴， 8mm 平键，及 M8 x 1,2 螺纹孔 (有防腐蚀保护层) ● 直径 1 英寸，直轴有 10,2 [.40] 直径的垂直通孔，离端面 15,7 [.62] 并端部还有 1/4-20 的螺纹孔 (有防
AFL M210e spel检测仪说明书
M210e Hand-held OTDRSpecifications aOTDR MULTIMODE SINGLE-MODEEmitter Type Laser LaserSafety Class Class I FDA 21 CFR 1040.10 and 1040.11; IEC 60825-1:2007-03Class I FDA 21 CFR 1040.10 and 1040.11; IEC 60825-1:2007-03 Center Wavelengths850/1300 nm1310/1550 nmWavelength Tolerance±20/±30 nm±20/±30 nmLaunch Condition n Controlled Launch at 850 nm n N/ALive Fiber Detection m Yes YesDynamic Range (SNR = 1) b28/28 dB34/33 dBEvent Dead Zone c 1.0 m 1.0 mAttenuation Dead Zone d 4.0 m 4.0 mPulse Widths5, 10, 30, 100, 300 ns, 1 µs,5, 10, 30, 100, 300 ns, 1, 3, 10 µs, 20 µsRange Settings250 m to 30 km250 m to 240 kmSampling Points Up to 120,000Up to 120,000Minimum Data Point Spacing e 3 cm 3 cmGroup Index of Refraction (GIR) 1.4000 to 1.6000 1.4000 to 1.6000Distance Uncertainty/Accuracy f±(1 +0.005 % x distance + data point spacing)±(1 +0.005 % x distance + data point spacing)Linearity g±0.05 dB/dB±0.05 dB/dBLoss Threshold0.02 dB0.02 dBLoss Resolution0.01 dB0.01 dBReflectance Range p, h850 nm: -14 to -58 dB (typical)1300 nm: -14 to -63 dB (typical)1310 nm -14 to -65 dB (typical) 1550 nm -14 to -65 dB (typical)Reflectance Resolution0.01 dB0.01 dBReflectance Accuracy h±2 dB±2 dBReal Time Refresh Rate j>2 Hz >2 HzUnits m, km, ft, kft, miOTDR Modes Full Auto, Expert, Real-TimeTrace File Format Bellcore GR-196 Version 1.1, Telcordia SR -4731 Issue 2Trace File Storage Medium Internal and USBTrace File Storage Capacity>1000 internal, 1000s on USBTrace File Transfer to PC USBNotes:a. All specifications valid at 23°C ±2°C (73.4°F ±3.6°F) unless otherwise specified.b. Longest Range and Pulse Width, 3 minutes Averaging Time, normal resolution.c. Typical distance between the two points 1.5 dB down each side of a reflective spike caused by a -40 dB (multimode)or -45 dB (single-mode) event using 10 ns pulse width.d. Typical distance from event location to point where trace is within 0.5 dB of backscatter.e. Range <8 km.f. Does not include GIR uncertainty. Is based on the trace and user positioned cursors.g. Typical.h. For a non-saturated event.j. 2 km Range, 100 ns.m. Signals greater than -20 dBm MMF and -30 dBm SMF will trigger the Live Fiber Indication warning.n. Comparable to Encircled Flux loss measurement on OM4 fiber networks.p. For OM1 fiber typical Backscatter Coefficient @850 nm -68 dB, @1300 nm -76 dB and attenuation coefficient @850 nm 2.77 dB, @1300 nm 0.52 dB.For OS1-OS2 fiber typical Backscatter Coefficient @1310 nm -79.6 dB, 1550 nm -82 dB and attenuation coefficient @1300 nm 0.31 dB, @1550 nm 0.18 dB.M210e Hand-held OTDRSpecifications aOPM (STANDARD)Calibrated Wavelengths 850, 1300, 1310, 1490, 1550, 1625, 1650 nm (displays up to 3 simultaneously)Detector Type InGaAs 2mmDisplay Range b+6 to -70 dBmAccuracy @ -10 dBm±0.25 dBResolution0.01 dBMeasurement Units dB, dBm, mWWavelength ID c YesSet Reference YesData Storage YesTone Detection d270 Hz, 330 Hz, 1 kHz, 2 kHzVFL (STANDARD)Emitter Type LaserSafety Class Class II FDA 21 CFR 1040.10 and 1040.11; IEC 825-1:1993, 60825-1:2007-03Wavelength635 nm ±20 nmOutput Power (nominal)0.8 mWGENERALDisplay Type 3.5-inch transflective color, high contrast, high reflectivity (20%) for optimum indoor/outdoor viewing , QVGA with touchscreen Size (in boot)23 x 11 x 7 cm (8.8 x 4.3 x 2.8 in)Weight<1.4 kg (3 lb)Power Removable Li-ion or AC/DC power adapter (input 100-240 V, ~1.5 A 47-63 Hz) output 18 V DC/3.6 A (can test while charging,can operate on AC with battery removed)Battery Life e16 hoursRecharge Time f 4 hoursAuto Shut Off0-60 minutesConnectivity USB host/full speed 1.1Operating Temperature-10°C to +50°CStorage Temperature-20°C to +60°CRelative Humidity0 to 95 % RH (non-condensing)DFS1 DIGITAL FIBERSCOPE SUPPORTField of View 400 x 300 µmOptical Resolution 4 µmDetection Capability 2 µmNotes:a. All specifications valid at 23°C ±2°C (73.4°F ±3.6°F) unless otherwise specified.b. Measurement Range:+3 to -65 dBm for 1300 to 1625 nm, and +3 to -60 dBm for 850 nmc. Wavelength ID Range:+3 to -50 dBm for 1300 to 1625 nm, and +3 to -40 dBm for 850 nmd. Tone Detect Range:+3 to -50 dBm 1300 to 1625 nm, and +3 to -40 dBm for 850 nme. Typical with new battery, per GR-196-Core Issue 2.f. Typical, from fully discharged to fully charged state, unit may be operating.All M210e OTDRs include a USB flash drive, an AC adapter, UCI switchable adapters for OTDR and OPM ports, trace analysis and documentation software and a quick reference guide.M210e Hand-held OTDRWhen ordering, select options as follows: Optical Configuration (NN), (U) for UPC connection and Language (LL). Add (HC) only if ordering the hard case option.Example: M210e-25U-01-HC -> This model number indicates M210e QUAD with the English/European language pack in the optional hard case.Ordering InformationDESCRIPTIONAFL NO.M210e QUAD Certification Kit (Tier 1 and 2): M210e QUAD, OLS4, DFS1* in hard case M210e-25K-01-HC2M210e QUAD Test and Inspection Kit (Tier 2): M210e QUAD, DFS1* in hard case M210e-25K-01-HC1M210e OTDR, SM (1310/1550), OPM, VFL in hard case M210e-20U-01-HC M210e OTDR, MM (850/1300) OPM, VFL in hard caseM210e-22U-01-HC M210e OTDR, QUAD (850/1300/1310/1550), OPM, VFL in hard case M210e-25U-01-HC M210e OTDR, SM (1310/1550) OPM, VFL in soft case M210e-20U-01M210e OTDR, MM (850/1300) OPM, VFL in soft caseM210e-22U-01M210e OTDR, QUAD (850/1300/1310/1550), OPM, VFL in soft caseM210e-25U-01* When ordering, specify DFS1 model (See Accessories Table below).Optical Configuration (NN)20 = 1310/1550 nm SM 22 = 850/1300 nm MM25 = 850/1300 nm MM and 1310/1550 nm SM OTDR port ferrule (U = UPC)Hard Case option (HC)(Select (HC) only if ordering hard case option)NN U LLL HCM210eM210e Models and Included AdaptersWAVELENGTHS (nm)DYNAMIC RANGE (dB)OTDR PORT ADAPTERS OPM PORT ADAPTERS AFL BASE MODEL NO.85013001310155034/33SC, FC SC, 2.5 mm Universal M210e-2028/28SC, ST SC, 2.5 mm Universal M210e-2228/28/34/33SC, FC, STSC, 2.5 mm UniversalM210e-25Quick Reference Guide Language (LLL)*ENG = EnglishCHS = Chinese, Simplified CHT = Chinese, Traditional DEU =GermanFRA = French ITA = Italian POL = PolishPOR = Portuguese SPA = Spanish TUR = Turkish*Specify Language for OTDR Quick Reference GuideInternational Sales and Service Contact InformationAvailable at /Test/ContactsAccessoriesDESCRIPTIONAFL NO.DFS1 Digital FiberScope PC/UPC inspection kit DFS1-00-04XU DFS1 Digital FiberScope APC inspection kit DFS1-00-04XA DFS1 Digital FiberScope kit without adapters DFS1-00-04XNFiber Ring, 50/125 µm multimode, 150 mFR1-M5-150-x1-x2 a Fiber Ring, Laser Optimized, 50 µm multimode, 150 m FR1-L5-150-x1-x2 a Fiber Ring, 62.5/125 mm multimode, 150 m FR1-M6-150-x1-x2 a Fiber Ring, single-mode, 150 mFR1-SM-150-y1-y2 a Wet Cleaning kit for SC/FC/ST/LC connectors 8500-20-0900Dry Cleaning kit8500-20-0901Basic Cleaning kit with carry caseFCP2-00-0900Basic Cleaning kit with MPO Cleaners and carry case FCP2-00-0901One-Click Cleaner SC, ST, FC (500+ cleans)8500-05-0001MZ One-Click Cleaner LC/MU (500+ cleans)8500-05-0002MZ One-Click Mini-100 SC, ST, FC (100+ cleans) 8500-05-0005MZ One-Click Mini-100 LC/MU (100+ cleans)8500-05-0006MZ One-Click Cleaner Ultra 2.5 SC, ST, FC (enlarged cleaning)8500-05-0007MZ One-Click Ultra Cleaner D-LC (Duplex LC, 500 cleans x 2)8500-05-0008MZNote:a. When ordering Fiber Rings, specify connector types (x1, x2, y1, y2).。
海康威视 1F201F自动过滤器漏斗商品说明书
Filter w/Automatic Drain
Installation
To install the Auto Drain, SHUT OFF AiR SUPPLY and depressurize the unit.
1. Remove bowl by unscrewing bowl or collar, turning unlocking ring, or turn bayonet lock 1/8 turn.
Safety Guide
For more complete information on recommended application guidelines, see the Safety Guide section of Pneumatic Division catalogs or you can download the Pneumatic Division Safety Guide at: /safety
TO CLEAN POLYCARBONATE BOWLS USE MILD SOAP AND WATER ONLY! DO NOT use cleansing agents such as acetone, benzene, carbon tetrachloride, gasoline, toluene, etc., which are damaging to this plastic.
Metal bowls are recommended where ambient and/or media conditions are not compatible with polycarbonate bowls. Metal bowls resist the action of most such solvents, but should not be used where strong acids or bases are present or in salt laden atmospheres. Consult the factory for specific recommendations where these conditions exist.
蜂窝海尔CO2传感器和差分压力传感器产品介绍说明书
Sensor Selection GuideSensing for Building ApplicationsCO 2SensorsThe Honeywell CO 2 sensor includes state-of-the-art non-dispersive infrared (NDIR) technology plus a corrosion-free-designed sensing chamber that provides accurate and stable CO 2 readings for years, avoiding costly and inconvenient re-calibration. A patented gold-plated sensing chamber eliminates a primary source of dirt. Paired with a Honeywell economizer, theHoneywell CO 2 sensor can triple year-round savings over “cooling only” economizing. The sensor is used in demand control ventilation applications to maintain acceptable levels of CO 2 in the space.Differential Pressure SensorsAll Honeywell differential pressure sensors offer field selectable 4-20 mA, 0-5 Vdc and 0-10 Vdc outputs, uni- and bi-directional outputs, push button and digital inputs to zero the output, and configurable pressure ranges. Use P7640 dry media sensors in applications where you want measure extremelylow pressure, such as clean rooms, hospitals, fume hoods and computer rooms. Use the PWT Series to monitor and control pump differential pressure, chiller/boiler differential pressure drop and CW/HW system differential pressure.Enthalpy SensorsHoneywell enthalpy sensors are used with Honeywell economizer logic modules to permit the use of outdoor air as the first stage of cooling in HVAC systems. Thelong-lasting solid-state sensing elements are accurate and stable over time. Maximum economizer savings are achieved when two enthalpy sensors are connected to one economizer logic module for differential enthalpy changeover control.Specify Honeywell Sensors And SaveHoneywell sensors have always been competitively priced, and today Honeywell sensors continue to be one of the industry’s best values. Add in the fact that their ease-of-installation increases your productivity and you’ll see that Honeywell sensors are the smart, cost-effective choice.2Honeywell’s complete line of sensor's cover all necessary control applications and mounting options, making Honeywell your best sensor source.Temperature SensorsYou can count on Honeywell temperature sensors for the latest technology, accurate performance and reliability. Honeywell temperature sensors feature solid-statecomponents and are impervious to dust and dirt.They cover a variety of applications that will fit your needs from averaging, immersion and outdoor sensors to duct-mount, wall mount and strap-on sensors.Current Sensors And SwitchesHoneywell current switches can detect whether current is flowing and then transmit the status to a building management system, DDC or PLC controller. Honeywellcurrent transmitters measure the level of operating current and can be used to monitor equipment or drive other equipment with a modulating output. Both current switches and transmitters can be used to detect a motor failure, belt loss or slippage, or a mechanical failure to help prevent further damage and reduce downtime. Because Honeywell current sensors are rated at up to 250 amps, you can meet high-amp applications without the need for a transformer. And Honeywell offers current switches with a very low trip point of 0.20 amps.Humidity SensorsHighly accurate, stable humidity transducers designed for use with HVAC controllers, thermostats and direct digital controllers, Honeywell humidity sensors feature a ceramic technology that’s affected by condensation. Applications include room comfort, rooftop units, air handlers, air conditioning and anywhere relative humidity is tightly controlled.Dew Point SensorsSuitable for mounting on flat and round surfaces, the Honeywell dew point sensor is used to regulate cooling performance, switch cooling systems ON and OFF, andsignal if the temperature is approaching the dew point.YOUR BeST SeNSOR SOURCe3thermostats and non-Honeywell thermostats with remote setpoint.* F or accessing virtually any point in thecontroller, balancing from wall module, etc. **TR75s also have over twice as much memory capacity for parameters as TR71's.4GeNeRAL TeMPeRATURe SeNSORST775-SENS-STRAPT775-SENS-OATT775-SENS-WRT775-SENS-WT50021579-001aFor use with T7350 applications. bFor use with W7100.* May be used with Duct Mounting Kit- Part # 50053060-001GeNeRAL TeMPeRATURe SeNSORS5NOTE: 20K ohms NTC sensors are used with excel 10, 15, 50, 100 and 500. See controller product data sheets for details. PT1000 sensors are used with excel 15, 100, 500, and 600. See controller product data sheets for details. PT3000 sensors are used on certain excel and Microcell products. See controller product data sheets for details. 3K ohm NTC sensors are used on W7100, W7459, W7215, W7212 an dall economizer modules. 10K ohms NTC Type II sensors are used with TB7600, TB7300, and TB7600 Series communicating thermostats. 10K ohms NTC Type III sensors are used with WeBs-AX I/OModules.C7041PC7041JC7041BTB-WALLC7041DC7041FC7041R6CURReNT SeNSORSSplit CoreSolid Core7HUMIDITY , DeW POINT, CO 2and PReSSURe SeNSORSH7655B, H7625B, H7635BC7600B, H7655AC7262A1008C7232BHSS-DPSAutomation and Control Solutions In the US: Honeywell1985 Douglas Drive North Golden Valley, MN 55422-3992In Canada: Honeywell Limited 35 Dynamic Drive Toronto, Ontario M1V 63-9285 PR October 2013© 2013 Honeywell International Inc.P7640BHUMIDITY , DeW POINT, CO 2and PReSSURe SeNSORS (CONT.)50035430PWT250Follow us on Twitter: @honeywellcproYouTube:@honeywellcpro。
智能手机说明书
Safety InstructionsZ o n e 2/22Smart-Ex ® 201 | Ex-Handy 209Content1. Application (4)1.1 ATEX & IECEx (4)1.2 NEC & CEC (4)2. Safety precautions (4)3. Faults and damage (4)4. Safety regulations (5)5. Ex-Data (6)5.1 ATEX (6)5.2 IECEx (6)5.3 NEC & CEC (7)7. Charging the Smartphone (9)8. Safety precautions for built-in battery (9)9. Repair (10)10. Cleaning, maintenance and storage (10)11. Disposal (11)12. Warranty and liability (12)13. EU Declaration of Conformity and Certificate (12)Note:The current safety instructions, operating instructions, EU Declaration of Con-formity and the Certificate of Conformity can be downloaded from the relevant product page at , or alternatively they can be requested di-rectly from the manufacturer.1. Application1.1 ATEX & IECExThe Smart-Ex 201 and Ex-Handy 209 are intrinsically safe water-, dust- and impact resistant Smartphones for industrial application in areas with an in-creased risk of explosion in zone 2 and zone 22 in accordance with directives 1999/92/EC, 2014/34/EU (ATEX) and the IECEx System.1.2 NEC & CECThe Smart-Ex 201 and Ex-Handy 209 are intrinsically safe water-, dust- and impact resistant Smartphones for industrial application in areas with an incre-ased risk of explosion. Approved for Division 2 / Zone 2 Class I.2. Safety precautionsThese safety instructions contain information and safety regulations which are to be observed without fail for safe operation in the described conditions. Non-observance of this information and these instructions can have serious conse-quences or it may violate regulations.Please read these safety instructions carefully before starting to use the de-vice! In the event of conflicting information the details specified in the safety instructions shall apply.In case of any doubt (in the form of translation or printing errors) the English version shall apply.3. Faults and damageIf there is any reason to suspect that the safety of the device has been impaired, it must be withdrawn from use and removed immediately from the hazardous area. Measures must be taken to prevent it from being used within the hazar-dous area accidentally.The safety of the device maybe compromised, if, for example:• There is visible damage to the housing.• The device has been subjected to excessive loads.• The device has been improperly stored.• The device has been damaged in transit.• Device markings or inscriptions are illegible.• Malfunctions occur.• Permitted limit values have been exceeded.4. Safety regulationsUse of the intrinsically safe Smartphone Smart-Ex 201 or Ex-Handy 209 as-sumes that the operator observes the conventional safety regulations and has read the certificate of conformity in order to eliminate malfunction of the device. The following items are to be observed:Operating conditions:• It must be ensured that the device is not taken into zones 0, 1, 20 or 21.• The device has to be protected against strong impacts.• The device must be protected against exposure to UV-radiation.• D o not disassemble or open the device excepted for the following reasons:It is allowed to open the SIM Card Cover in ordinary locations to get access to the card. Before entering the hazardous locations the SIM Card cover must be mounted. The Audio Jack cover must not be closed inside and outside hazardous locations.Electrostatic:• T he unit must not be used in close proximity to processes generating high electrostatic charges.Charging and data connections:• T he Smartphone may only be charged outside the hazardous area.• The Smartphone may only be charged in a temperature range of 0 – 45 °C.• The data transfer connections is only allowed outside the hazardous areas. • The nominal voltage for charging is 5V• F or charging or data transfer connections the USB data cable PC S201 must be used.• I t is only allowed to connect devices to the USB interface in ordinary locations. Before entering the hazardous location It must be ensured that nothing Is connected to the SB plug.• I t must be ensured that the power supply used fulfills requirements. Accessoires:• O nly accessories approved by ecom instruments GmbH may be used or intrinsically safe accessories applying to the relevant entity parameter for the audio jack as stated in document 500059EX04A.• R ecognized accessories are listed on the relevant product page at www. .• W ired headsets may only be used inside hazardous areas if the headset itself is certified for use inside hazardous areas and the headset meets the inter-face parameter of the Smartphone. In such case the Ex-Marking and special conditions of certification of the accessory must be observed additionally. 5. Ex-Data5.1 ATEXATEX Certificate of Conformity no.: EPS 15 ATEX 1 994 XRelevant Standards: EN 60079-0:2012/A11:201360079-11:2012ENEx-Marking: † II 3G Ex ic IIC T4 Gc IP64† II 3D Ex ic IIIB T135°C Dc IP64Ambient temperature: -20 °C ≤ Tamb ≤ +55 °CApproved for zone 2, device group II, explosion group IIC (explosive gases, vapors or mist), temperature class T4. Approved for zone 22, device group II, explosion group IIIB (combustible flying, non-conductive dust), maximum Tem-perature 135°C.5.2 IECExIECEx Certificate of Conformity no.: IECEx EPS 15.0031XRelevant Standards: EN 60079-0 ed.6EN 60079-11 ed.6Ex-Marking: Ex ic IIC T4 Gc IP64Ex ic IIIB T135°C Dc IP64Ambient temperature: -20 °C ≤ Tamb ≤ +55 °CApproved for zone 2, device group II, explosion group IIC (explosive gases, vapors or mist), temperature class T4. Approved for zone 22, device group II, explosion group IIIB (combustible flying, non-conductive dust), maximum Temperature 135°C.5.3 NEC & CECEx-Marking: NI CL I DIV 2 GRP A-D T4Class I Zone 2 Group IIC T4Ambient temperature: -20 °C ≤ Ta ≤ +55 °CApproved for Division 2 / Zone 2, Class I.Please note: Only devices showing the FCC and IC identification numbers are approved and certified to be used in the United States and Canada6. SpecificationsOperating system: Android 4.4 (Kitkat)Networks: EDGE 850/900/1800/1900 MHzHSPA 850/900/1700/2100 MHzLTE 800/900/1800/2100/2600 MHz (EU)or 700/850/900/1700/1800/1900/2100/2600 MHz (US) Bluetooth: 4.0/BLE (Bluetooth Low Energy)Power supply: Li-Ion battery 4800 mAh, 3.8 V (built-in)CE-designation: 0560Protection class: IP68 (for 30 minutes, 2 meters under water)SAR: max. 0.358 W/kg (10g) Smart-Ex 201max. 0.327 W/kg (10g) Ex-Handy 209Inserting the SIM Card:1. R emove the screws of the headset port cover and the SIM card cover with the provided Multitool “MT S01” and remove both covers.2. I nsert the pin of the Multitool “MT S01” into the pinhole and press inside. The SIM card tray will pop-up. Use the pin to hook into the loop on top of the SIM card tray and remove the tray completely.3. I nsert the SIM card in the tray and return the tray into the slot by pushing it in. Making sure the pinhole is aligned next to the headset port.4. Refix both the covers and screws in place using the Multitool “MT S01”.Notice:Insert SIM card tray as shown to avoid damage to the card.This information is also shown on the protection film affixed to the display of the Smartphones. For optimaluse of the touch screen you should remove the pro -tection film before using the Smartphone for the firsttime.None of the openings at either side of the device are reset buttons! The insertion of sharp objects will damage components of the device that are mandatory for the Ex-safety. Do not insert any objects intoopenings of the device!7. Charging the SmartphoneCharging the Smartphone is allowed only outside hazardous areas!The battery of the Smartphone is not fully charged. It is recommended to char-ge the phone for five hours before using it for the first time. The full capacity of the battery is reached after 3-4 complete charge/discharge cycles.Note:• There is a risk of explosion if the device is exposed to a flame.• Only use ecom charging accessories (see point 4).Don’t attempt to replace the Smart-Ex 201 or Ex-Handy 209 battery yourself—you may damage the battery, which could cause overheating and injury. Note that when opened by an unauthorized person, the Ex-protection as well as the warranty is void.In case the lithium-ion battery in Smart-Ex 201 or Ex-Handy 209 has to be replaced only by ecom instruments GmbH or by personnel or service centers authorized by ecom instruments GmbH, and must be recycled or disposed of separately from household waste. Don’t incinerate the battery.• T he charge level of the device has to be checked after 9 months at the latest in order to prevent deep discharge.• I f the battery is completely discharged, the phone will not switch on and the display will not show a charging process. Connect the phone to the charger. After charging for a few minutes the display will appear again and you can then switch on the phone.8. Safety precautions for built-in batteryDamaged devices and chargers should be removed from use and sent to ecom instruments GmbH for inspection. When sending batteries/battery packs or devices containing batteries/battery packs; the sender must comply with the transport regulations for dangerous goods.Note:• Extreme temperatures can have an adverse effect on charging the battery.• Do not dispose of the device in a fire.• D ispose of the device in accordance with local regulations and not with normal household waste.High quality lithium-ion batteries are used in your Smart-Ex 201 and Ex-Handy 209. These batteries have numerous advantages in everyday use, such as a low weight and high capacity in a nevertheless compact construction. In addition these batteries also exhibit practically no memory effect. However, these batte-ries are susceptible to a natural aging process which impairs their functionality. Modern batteries today have a lifespan of around 500 charge cycles, which, when used daily, corresponds to a service life of approximately 2 years. The ageing process increases rapidly after this period, which means that the bat-teries are deemed technically defective after 500 charge cycles. Moreover, the battery cells could expand and cause irreparable damage to your device in a worst case scenario.For this reason rechargeable batteries with lithium cells should be replaced after 2 years at the latest or after reaching a battery capacity that is 50% of its initial value.Note:The battery used in this unit poses a fire hazard and can cause chemical inju-ries if it is used improperly. Neither the battery nor the battery cells should be opened or disassembled and they should not be burned or exposed to tempe-ratures exceeding 100 °C.9. RepairRepairs are to be conducted by ecom instruments GmbH or by personnel or service centers authorized by ecom instruments GmbH, because the safety of the device needs to be tested after repairs are implemented.The actual repair report sheet can be downloaded from the service area at .10. Cleaning, maintenance and storage• Only use a suitable cloth or sponge to clean the phone.• Do not use any solvents or abrasive cleaning agents when cleaning.• I t is recommended that you have the functionality and accuracy of the phone inspected by the manufacturer every two years.• D o not exceed the permissible storage temperature range of -20 °C ... +55 °C!• T he device should only be stored within a range of -20 °C to +40 °C (for up to 3 months) or within a range of -20 °C to +50 °C (for up to 1 month).11. DisposalOld electrical devices by ecom instruments GmbH will be directed to disposal at our expense and disposed of free of charge in accordance with European Directive 2002/96/EC. Please follow local regulations for the disposal of electronic products. The costs associated with returning devices to ecom instruments GmbH are to be borne by the sender.In accordance with Article 1, Section 18 and Article 2 of the Act revising the law of Waste-Related Product Responsibility for Batteries and Accumulators (Gesetz zur Neuregelung der abfallrechtlichen Produktverantwortung für Batterien und Akkumulatoren) dated 25 June 2009, we are obligated to provide the following information.Your device contains a rechargeable lithium battery.Depleted batteries or rechargeable batteries that can no longer be rechar-ged should never be disposed of along with normal or household waste. Old batteries can contain harmful substances that are hazardous to health and damaging to the environment. Please return the batteries/rechargeable batteries. Return is free of charge and required by law. Please only dispose of discharged batteries in the designated containers and tape the terminals of lithium batteries.Note: The battery used in this unit poses a fire hazard and can cause chemical injuries if it is used improperly. Neither the battery nor the battery cells should be opened or disassembled and they should not be burned or exposed to temperatures exceeding 100 °C. If the battery needs to be disposed of, it can be removed as described under point (7). The disposal regulations specified above are also applicable for old devices.All batteries and rechargeable batteries can be recycled. Precious raw materi-be disposed of along with normal or household waste.12. Warranty and liabilityThe warranty of this product follows the General Conditions of Delivery and Payment of ecom instruments GmbH, which are available at www.ecom-ex. com, or alternatively they can be requested directly from the manufacturer. This warranty can be extended by the optional Service Level Agreement.13. EU Declaration of Conformity and CertificateThe EU declaration and the certificate of conformity is enclosed with the sales packaging as a separate document.Please also observe the information provided underneath the table of contents.Copyright © 2013 ecom instruments GmbH.Der Inhalt dieses Dokuments darf ohne vorherige schriftliche Genehmigung durch die ecom instruments GmbH in keiner Form, weder ganz noch teilweise vervielfältigt, weitergegeben, verbreitet oder gespeichert werden.Der Inhalt dieses Dokuments wird so präsentiert, wie er aktuell vorliegt. Die ecom instruments GmbH übernimmt weder ausdrücklich noch stillschweigend irgendeine Gewährleistung für dieRichtigkeit oder Vollständigkeit des Inhalts dieses Dokuments, einschließlich, aber nichtbeschränkt auf die stillschweigende Garantie der Markttauglichkeit und der Eignung für einen bestimmten Zweck, es sei denn, anwendbare Gesetze oder Rechtsprechungen schreiben zwingend eine Haftung vor. Die ecom instruments GmbH behält sich das Recht vor, jederzeit ohne vorherige Ankündigung Änderungen an diesem Dokument vorzunehmen oder das Dokument zurückzuziehen.Copyright © 2013 ecom instruments GmbH.The contents of this document, either in part or in their entirety, may not be reproduced, forwarded, distributed or saved in any way without ecom instruments GmbH prior written consent.The contents of this document are presented as they currently exist. ecom instruments GmbH does not provide any express or tacit guarantee for the correctness or completeness of the contents of this docu-ment, including, but not restricted to, the tacit guarantee of market suitability or fitness for a specific purpose unless applicable laws or court decisions make liability mandatory. ecom instruments GmbH reserves the right to make changes to this document or to withdraw it any time without prior notice.ecom instruments GmbH | Industriestraße 2 | 97959 Assamstadt | Germany Phone +49 62 94 42 24 0 | Fax +49 62 94 42 24 100 *****************|PA000620| 07/2016500059AL01A02 05/2015WEEE-Reg.-Nr. DE 934 99306Änderungen vorbehalten! Subject to change without notice.。
el-o-matic定位器F20+PTF20阀门执行机构-深圳立创
随着时间的推移，先进科学技术的不断发展，使得各类控制系统更加的先进化，成熟化。
现今，该类控制系统已广泛应用到世界各地的各个行业。
阀门定位器，定位器在过程控制中是一种非常重要的仪表，它快速而有效的转换其所得到的信号，并根据该信号对阀门开度在0～100％之间进行精确调节。
el-o-matic的“POSifleX”阀门定位器是一种高精度、高可靠性的仪表，其在过程控制中起到了非常重要的作用。
E L-O-M A T I C气动执行器为荷兰生产,是世界上最大的专门致力于开发和生产阀门执行机构的公司之一，该执行器已经广泛在美国,加拿大等市场使用,该执行器使用寿命在50万次以上.可在各种场合使用。
“POSiflex”阀门定位器“POsifleX”系列阀门定位器主要包括3种类型：F10气动阀门定位器、F20电气阀门定位器和P40数字式电气阀门定位器，它们适用于需要精确定位的单作用和双作用的气动执行机构，同时它们也可以被用在其他控制行程上。
所有的“POSifleX”系列阀门定位器都具有坚固的、可抵御各种外部腐蚀、涂有环氧树脂漆的铸造铝合金外壳，它采用模块式结构可以满足使用者不同的要求。
（模块化结构备广泛应用在最新一带的电动执行机构，插入式模块可以很容易的扩展整个控制功能，它可以使功能单一的机型机构很容易的扩展成一个功能齐全的执行机构，同时还具有传统的4-20MA模拟量信号和最新的数字通信功能。
）一般描述●可应用于角行程和直行程执行机构。
●涂有环氢树脂漆的优质铝合金外壳。
●适用于单作用(弹簧复位)、双作用执行机构。
●正／反作用。
●标准连接VDI ／VDE3845(NAMUR)方式。
●模块结构，易于扩展。
F10●气动阀门定位器。
●具有简单、坚固的结构。
●完全的机械装置。
●外部零点设置。
●外壳：防护等级IP54，可选IP65。
F20●电气阀门定位器。
●模拟量电信号(4～20mA)。
●通过跳线可分程控制和正/反作用。
●防爆等级可选本质安全型EEX ib ⅡCT6。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
0 0 25 50 75 100 125 150175
1cm
SET TIME BASE FOR 10 ns/cm
AMBIENT TEMPERATURE (
)
FIG. 3 - TYPICAL REVERSE CHARACTERISTICS
INSTANTANEOUS REVERSE CURRENT, (uA) INSTANTANEOUS FORWARD CURRENT, (A)
0
C
ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Forward Voltage at 2.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage Maximum Reverse Recovery Time (Note 1) NOTES : 1. Test Conditions: IF=0.5A, IR=-1.0A, IRR=-0.25A. 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts. @T A = 25 o C @T A =150 o C SYMBOL VF IR trr EFM201 EFM202 EFM203 0.95 EFM204 EFM205 EFM206 1.25 UNITS Volts uAmps 50 35 nSec 2001-5
FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10
20 4
100
~E FMLeabharlann M2EFTJ = 100
EF
1.0
.1
.1
TJ = 25
Pulse Width = 300uS 1% Duty Cycle
.01
.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%)
DO-214AA
0.083 (2.11) 0.077 (1.96) 0.180 (4.57) 0.160 (4.06)
MECHANICAL DATA
* Epoxy : Device has UL flammability classification 94V-0
0.155 (3.94) 0.130 (3.30)
FEATURES
* * * * * * Glass passivated device Ideal for surface mounted applications Low leakage current Metallurgically bonded construction Mounting position: Any Weight: 0.098 gram
FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 105 90 75 60 45 30 15 0 1 2 5 10 20 50 NUMBER OF CYCLES AT 60Hz 100
8.3ms Single Half Sine-Wave (JEDEC Method)
PEAK FORWARD SURGE CURRENT, (A)
.001 0 .2 .4 .6 .8 1.0 1.2 1.4 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 6 - TYPICAL JUNCTION CAPACITANCE
JUNCTION CAPACITANCE, (pF)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%.
200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 100
TJ = 25
EFM 201
M
20
10
01
TJ = 25
5~
1.0
EF M
TJ = 150
20 6
EFM
~EF
205
M2
04
~EF
M2
06
REVERSE VOLTAGE, ( V )
RECTRON
元器件交易网
RECTRON
SEMICONDUCTOR
TECHNICAL SPECIFICATION
EFM201 THRU EFM206
SURFACE MOUNT GLASS PASSIVATED SUPER FAST SILICON RECTIFIER
VOLTAGE RANGE 50 to 400 Volts CURRENT 2.0 Amperes
o
0.096 (2.44) 0.084 (2.13) 0.060 (1.52) 0.030 (0.76) 0.220 (5.59) 0.205 (5.21)
0.012 (0.305) 0.006 (0.152)
0.008 (0.203) 0.004 (0.102)
Dimensions in inches and (millimeters)
MAXIMUM RATINGS (At T A = 25 oC unless otherwise noted) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Volts Maximum DC Blocking Voltage Maximum Average Forward Current at T A = 55 oC Peak Forward Surge Current I FM (surge): 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range SYMBOL VRRM VRMS VDC IO I FSM CJ T J , T STG 30 -65 to + 175 EFM201 50 35 50 EFM202 100 70 100 EFM203 150 105 150 2.0 75 20 EFM204 200 140 200 EFM205 300 210 300 EFM206 400 280 400 UNITS Volts Volts Volts Amps Amps pF
5.0
元器件交易网
RATING AND CHARACTERISTIC CURVES ( EFM201 THRU EFM206 )
AVERAGE FORWARD CURENT, (A)
FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC
50 NONINDUCTIVE 10 NONINDUCTIVE
FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE
3.0 2.0
Single Phase Half Wave 60Hz Resistive or Inductive Load
trr +0.5A
(-) PULSE GENERATOR (NOTE 2)
(+) 25 Vdc (approx) (-)
D.U.T
0 -0.25A
1 NONINDUCTIVE
OSCILLOSCOPE (NOTE 1)
(+)
1.0
-1.0A
NOTES:1 Rise Time = 7ns max. Input Impedance =
1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms.