外文翻译=从生态加工技术对攻丝的研究=2500字符_毕业论文
机械加工毕业论文中英文资料外文翻译文献
毕业论文中英文资料外文翻译文献附录附录1：英文原文Selection of optimum tool geometry and cutting conditionsusing a surface roughness prediction model for end milling Abstract Influence of tool geometry on the quality of surface produced is well known and hence any attempt to assess the performance of end milling should include the tool geometry. In the present work, experimental studies have been conducted to see the effect of tool geometry (radial rake angle and nose radius) and cutting conditions (cutting speed and feed rate) on the machining performance during end milling of medium carbon steel. The first and second order mathematical models, in terms of machining parameters, were developed for surface roughness prediction using response surface methodology (RSM) on the basis of experimental results. The model selected for optimization has been validated with the Chi square test. The significance of these parameters on surface roughness has been established with analysis of variance. An attempt has also been made to optimize the surface roughness prediction model using genetic algorithms (GA). The GA program gives minimum values of surface roughness and their respective optimal conditions.1 IntroductionEnd milling is one of the most commonly used metal removal operations in industry because of its ability to remove material faster giving reasonably good surface quality. It is used in a variety of manufacturing industries including aerospace and automotive sectors, where quality is an important factor in the production of slots, pockets, precision moulds and dies. Greater attention is given to dimensional accuracy and surface roughness of products by the industry these days. Moreover, surface finish influences mechanical properties such as fatigue behaviour, wear, corrosion, lubrication and electrical conductivity. Thus, measuring and characterizing surface finish can be considered for predicting machining performance.Surface finish resulting from turning operations has traditionally received considerable research attention, where as that of machining processes using multipoint cutters, requires attention by researchers. As these processes involve large number of parameters, it would bedifficult to correlate surface finish with other parameters just by conducting experiments. Modelling helps to understand this kind of process better. Though some amount of work has been carried out to develop surface finish prediction models in the past, the effect of tool geometry has received little attention. However, the radial rake angle has a major affect on the power consumption apart from tangential and radial forces. It also influences chip curling and modifies chip flow direction. In addition to this, researchers [1] have also observed that the nose radius plays a significant role in affecting the surface finish. Therefore the development of a good model should involve the radial rake angle and nose radius along with other relevant factors.Establishment of efficient machining parameters has been a problem that has confronted manufacturing industries for nearly a century, and is still the subject of many studies. Obtaining optimum machining parameters is of great concern in manufacturing industries, where the economy of machining operation plays a key role in the competitive market. In material removal processes, an improper selection of cutting conditions cause surfaces with high roughness and dimensional errors, and it is even possible that dynamic phenomena due to auto excited vibrations may set in [2]. In view of the significant role that the milling operation plays in today’s manufacturing world, there is a need to optimize the machining parameters for this operation. So, an effort has been made in this paper to see the influence of tool geometry(radial rake angle and nose radius) and cutting conditions(cutting speed and feed rate) on the surface finish produced during end milling of medium carbon steel. The experimental results of this work will be used to relate cutting speed, feed rate, radial rake angle and nose radius with the machining response i.e. surface roughness by modelling. The mathematical models thus developed are further utilized to find the optimum process parameters using genetic algorithms.2 ReviewProcess modelling and optimization are two important issues in manufacturing. The manufacturing processes are characterized by a multiplicity of dynamically interacting process variables. Surface finish has been an important factor of machining in predicting performance of any machining operation. In order to develop and optimize a surface roughness model, it is essential to understand the current status of work in this area.Davis et al. [3] have investigated the cutting performance of five end mills having various helix angles. Cutting tests were performed on aluminium alloy L 65 for three milling processes (face, slot and side), in which cutting force, surface roughness and concavity of a machined plane surface were measured. The central composite design was used to decide on the number of experiments to be conducted. The cutting performance of the end mills was assessed usingvariance analysis. The affects of spindle speed, depth of cut and feed rate on the cutting force and surface roughness were studied. The investigation showed that end mills with left hand helix angles are generally less cost effective than those with right hand helix angles. There is no significant difference between up milling and down milling with regard tothe cutting force, although the difference between them regarding the surface roughness was large. Bayoumi et al.[4] have studied the affect of the tool rotation angle, feed rate and cutting speed on the mechanistic process parameters (pressure, friction parameter) for end milling operation with three commercially available workpiece materials, 11 L 17 free machining steel, 62- 35-3 free machining brass and 2024 aluminium using a single fluted HSS milling cutter. It has been found that pressure and friction act on the chip – tool interface decrease with the increase of feed rate and with the decrease of the flow angle, while the cutting speed has a negligible effect on some of the material dependent parameters. Process parameters are summarized into empirical equations as functions of feed rate and tool rotation angle for each work material. However, researchers have not taken into account the effects of cutting conditions and tool geometry simultaneously; besides these studies have not considered the optimization of the cutting process.As end milling is a process which involves a large number f parameters, combined influence of the significant parameters an only be obtained by modelling. Mansour and Abdallaet al. [5] have developed a surface roughness model for the end milling of EN32M (a semi-free cutting carbon case hardening steel with improved merchantability). The mathematical model has been developed in terms of cutting speed, feed rate and axial depth of cut. The affect of these parameters on the surface roughness has been carried out using response surface methodology (RSM). A first order equation covering the speed range of 30–35 m/min and a second order equation covering the speed range of 24–38 m/min were developed under dry machining conditions. Alauddin et al. [6] developed a surface roughness model using RSM for the end milling of 190 BHN steel. First and second order models were constructed along with contour graphs for the selection of the proper combination of cutting speed and feed to increase the metal removal rate without sacrificing surface quality. Hasmi et al. [7] also used the RSM model for assessing the influence of the workpiece material on the surface roughness of the machined surfaces. The model was developed for milling operation by conducting experiments on steel specimens. The expression shows, the relationship between the surface roughness and the various parameters; namely, the cutting speed, feed and depth of cut. The above models have not considered the affect of tool geometry on surface roughness.Since the turn of the century quite a large number of attempts have been made to find optimum values of machining parameters. Uses of many methods have been reported in the literature to solve optimization problems for machining parameters. Jain and Jain [8] have usedneural networks for modeling and optimizing the machining conditions. The results have been validated by comparing the optimized machining conditions obtained using genetic algorithms. Suresh et al. [9] have developed a surface roughness prediction model for turning mild steel using a response surface methodology to produce the factor affects of the individual process parameters. They have also optimized the turning process using the surface roughness prediction model as the objective function. Considering the above, an attempt has been made in this work to develop a surface roughness model with tool geometry and cutting conditions on the basis of experimental results and then optimize it for the selection of these parameters within the given constraints in the end milling operation.3 MethodologyIn this work, mathematical models have been developed using experimental results with the help of response surface methodolog y. The purpose of developing mathematical models relating the machining responses and their factors is to facilitate the optimization of the machining process. This mathematical model has been used as an objective function and the optimization was carried out with the help of genetic algorithms.3.1 Mathematical formulationResponse surface methodology(RSM) is a combination of mathematical and statistical techniques useful for modelling and analyzing the problems in which several independent variables influence a dependent variable or response. The mathematical models commonly used are represented by:where Y is the machining response, ϕ is the response function and S, f , α, r are milling variables and ∈is the error which is normally distributed about the observed response Y with zero mean.The relationship between surface roughness and other independent variables can be represented as follows，where C is a constant and a, b, c and d are exponents.To facilitate the determination of constants and exponents, this mathematical model will have to be linearized by performing a logarithmic transformation as follows:The constants and exponents C, a, b, c and d can be determined by the method of least squares. The first order linear model, developed from the above functional relationship using least squares method, can be represented as follows:where Y1 is the estimated response based on the first-order equation, Y is the measured surface roughness on a logarithmic scale, x0 = 1 (dummy variable), x1, x2, x3 and x4 are logarithmic transformations of cutting speed, feed rate, radial rake angle and nose radiusrespectively, ∈is the experimental error and b values are the estimates of corresponding parameters.The general second order polynomial response is as given below:where Y2 is the estimated response based on the second order equation. The parameters, i.e. b0, b1, b2, b3, b4, b12, b23, b14, etc. are to be estimated by the method of least squares. Validity of the selected model used for optimizing the process parameters has been tested with the help of statistical tests, such as F-test, chi square test, etc. [10].3.2 Optimization using genetic algorithmsMost of the researchers have used traditional optimization techniques for solving machining problems. The traditional methods of optimization and search do not fare well over a broad spectrum of problem domains. Traditional techniques are not efficient when the practical search space is too large. These algorithms are not robust. They are inclined to obtain a local optimal solution. Numerous constraints and number of passes make the machining optimization problem more complicated. So, it was decided to employ genetic algorithms as an optimization technique. GA come under the class of non-traditional search and optimization techniques. GA are different from traditional optimization techniques in the following ways:1.GA work with a coding of the parameter set, not the parameter themselves.2.GA search from a population of points and not a single point.3.GA use information of fitness function, not derivatives or other auxiliary knowledge.4.GA use probabilistic transition rules not deterministic rules.5.It is very likely that the expected GA solution will be the global solution.Genetic algorithms (GA) form a class of adaptive heuristics based on principles derived from the dynamics of natural population genetics. The searching process simulates the natural evaluation of biological creatures and turns out to be an intelligent exploitation of a random search. The mechanics of a GA is simple, involving copying of binary strings. Simplicity of operation and computational efficiency are the two main attractions of the genetic algorithmic approach. The computations are carried out in three stages to get a result in one generation or iteration. The three stages are reproduction, crossover and mutation.In order to use GA to solve any problem, the variable is typically encoded into a string (binary coding) or chromosome structure which represents a possible solution to the given problem. GA begin with a population of strings (individuals) created at random. The fitness of each individual string is evaluated with respect to the given objective function. Then this initial population is operated on by three main operators – reproduction cross over and mutation– to create, hopefully, a better population. Highly fit individuals or solutions are given theopportunity to reproduce by exchanging pieces of their genetic information, in the crossover procedure, with other highly fit individuals. This produces new “offspring” solutions, which share some characteristics taken from both the parents. Mutation is often applied after crossover by altering some genes (i.e. bits) in the offspring. The offspring can either replace the whole population (generational approach) or replace less fit individuals (steady state approach). This new population is further evaluated and tested for some termination criteria. The reproduction-cross over mutation- evaluation cycle is repeated until the termination criteria are met.4 Experimental detailsFor developing models on the basis of experimental data, careful planning of experimentation is essential. The factors considered for experimentation and analysis were cutting speed, feed rate, radial rake angle and nose radius.4.1 Experimental designThe design of experimentation has a major affect on the number of experiments needed. Therefore it is essential to have a well designed set of experiments. The range of values of each factor was set at three different levels, namely low, medium and high as shown in Table 1. Based on this, a total number of 81 experiments (full factorial design), each having a combination of different levels of factors, as shown in Table 2, were carried out.The variables were coded by taking into account the capacity and limiting cutting conditions of the milling machine. The coded values of variables, to be used in Eqs. 3 and 4, were obtained from the following transforming equations:where x1 is the coded value of cutting speed (S), x2 is the coded value of the feed rate ( f ), x3 is the coded value of radial rake angle(α) and x4 is the coded value of nose radius (r).4.2 ExperimentationA high precision ‘Rambaudi Rammatic 500’ CNC milling machine, with a vertical milling head, was used for experimentation. The control system is a CNC FIDIA-12 compact. The cutting tools, used for the experimentation, were solid coated carbide end mill cutters of different radial rake angles and nose radii (WIDIA: DIA20 X FL38 X OAL 102 MM). The tools are coated with TiAlN coating. The hardness, density and transverse rupture strength are 1570 HV 30, 14.5 gm/cm3 and 3800 N/mm2 respectively.AISI 1045 steel specimens of 100×75 mm and 20 mm thickness were used in the present study. All the specimens were annealed, by holding them at 850 ◦C for one hour and then cooling them in a furnace. The chemical analysis of specimens is presented in Table 3. Thehardness of the workpiece material is 170 BHN. All the experiments were carried out at a constant axial depth of cut of 20 mm and a radial depth of cut of 1 mm. The surface roughness (response) was measured with Talysurf-6 at a 0.8 mm cut-off value. An average of four measurements was used as a response value.5 Results and discussionThe influences of cutting speed, feed rate, radial rake angle and nose radius have been assessed by conducting experiments. The variation of machining response with respect to the variables was shown graphically in Fig. 1. It is seen from these figures that of the four dependent parameters, radial rake angle has definite influence on the roughness of the surface machined using an end mill cutter. It is felt that the prominent influence of radial rake angle on the surface generation could be due to the fact that any change in the radial rake angle changes the sharpness of the cutting edge on the periphery, i.e changes the contact length between the chip and workpiece surface. Also it is evident from the plots that as the radial rake angle changes from 4◦to 16◦, the surface roughness decreases and then increases. Therefore, it may be concluded here that the radial rake angle in the range of 4◦to 10◦would give a better surface finish. Figure 1 also shows that the surface roughness decreases first and then increases with the increase in the nose radius. This shows that there is a scope for finding the optimum value of the radial rake angle and nose radius for obtaining the best possible quality of the surface. It was also found that the surface roughness decreases with an increase in cutting speed and increases as feed rate increases. It could also be observed that the surface roughness was a minimum at the 250 m/min speed, 200 mm/min feed rate, 10◦radial rake angle and 0.8 mm nose radius. In order to understand the process better, the experimental results can be used to develop mathematical models using RSM. In this work, a commercially available mathematical software package (MATLAB) was used for the computation of the regression of constants and exponents.5.1 The roughness modelUsing experimental results, empirical equations have been obtained to estimate surface roughness with the significant parameters considered for the experimentation i.e. cutting speed, feed rate, radial rake angle and nose radius. The first order model obtained from the above functional relationship using the RSM method is as follows:The transformed equation of surface roughness prediction is as follows:Equation 10 is derived from Eq. 9 by substituting the coded values of x1, x2, x3 and x4 in termsof ln s, ln f , lnαand ln r. The analysis of the variance (ANOV A) and the F-ratio test have been performed to justify the accuracy of the fit for the mathematical model. Since the calculated values of the F-ratio are less than the standard values of the F-ratio for surface roughness as shown in Table 4, the model is adequate at 99% confidence level to represent the relationship between the machining response and the considered machining parameters of the end milling process.The multiple regression coefficient of the first order model was found to be 0.5839. This shows that the first order model can explain the variation in surface roughness to the extent of 58.39%. As the first order model has low predictability, the second order model has been developed to see whether it can represent better or not.The second order surface roughness model thus developed is as given below:where Y2 is the estimated response of the surface roughness on a logarithmic scale, x1, x2, x3 and x4 are the logarithmic transformation of speed, feed, radial rake angle and nose radius. The data of analysis of variance for the second order surface roughness model is shown in Table 5.Since F cal is greater than F0.01, there is a definite relationship between the response variable and independent variable at 99% confidence level. The multiple regression coefficient of the second order model was found to be 0.9596. On the basis of the multiple regression coefficient (R2), it can be concluded that the second order model was adequate to represent this process. Hence the second order model was considered as an objective function for optimization using genetic algorithms. This second order model was also validated using the chi square test. The calculated chi square value of the model was 0.1493 and them tabulated value at χ2 0.005 is 52.34, as shown in Table 6, which indicates that 99.5% of the variability in surface roughness was explained by this model.Using the second order model, the surface roughness of the components produced by end milling can be estimated with reasonable accuracy. This model would be optimized using genetic algorithms (GA).5.2 The optimization of end millingOptimization of machining parameters not only increases the utility for machining economics, but also the product quality toa great extent. In this context an effort has been made to estimate the optimum tool geometry and machining conditions to produce the best possible surface quality within the constraints.The constrained optimization problem is stated as follows: Minimize Ra using the model given here:where xil and xiu are the upper and lower bounds of process variables xi and x1, x2, x3, x4 are logarithmic transformation of cutting speed, feed, radial rake angle and nose radius.The GA code was developed using MATLAB. This approach makes a binary coding system to represent the variables cutting speed (S), feed rate ( f ), radial rake angle (α) and nose radius (r), i.e. each of these variables is represented by a ten bit binary equivalent, limiting the total string length to 40. It is known as a chromosome. The variables are represented as genes (substrings) in the chromosome. The randomly generated 20 such chromosomes (population size is 20), fulfilling the constraints on the variables, are taken in each generation. The first generation is called the initial population. Once the coding of the variables has been done, then the actual decoded values for the variables are estimated using the following formula: where xi is the actual decoded value of the cutting speed, feed rate, radial rake angle and nose radius, x(L) i is the lower limit and x(U) i is the upper limit and li is the substring length, which is equal to ten in this case.Using the present generation of 20 chromosomes, fitness values are calculated by the following transformation:where f(x) is the fitness function and Ra is the objective function.Out of these 20 fitness values, four are chosen using the roulette-wheel selection scheme. The chromosomes corresponding to these four fitness values are taken as parents. Then the crossover and mutation reproduction methods are applied to generate 20 new chromosomes for the next generation. This processof generating the new population from the old population is called one generation. Many such generations are run till the maximum number of generations is met or the average of four selected fitness values in each generation becomes steady. This ensures that the optimization of all the variables (cutting speed, feed rate, radial rake angle and nose radius) is carried out simultaneously. The final statistics are displayed at the end of all iterations. In order to optimize the present problem using GA, the following parameters have been selected to obtain the best possible solution with the least computational effort: Table 7 shows some of the minimum values of the surface roughness predicted by the GA program with respect to input machining ranges, and Table 8 shows the optimum machining conditions for the corresponding minimum values of the surface roughness shown in Table 7. The MRR given in Table 8 was calculated bywhere f is the table feed (mm/min), aa is the axial depth of cut (20 mm) and ar is the radial depth of cut (1 mm).It can be concluded from the optimization results of the GA program that it is possible toselect a combination of cutting speed, feed rate, radial rake angle and nose radius for achieving the best possible surface finish giving a reasonably good material removal rate. This GA program provides optimum machining conditions for the corresponding given minimum values of the surface roughness. The application of the genetic algorithmic approach to obtain optimal machining conditions will be quite useful at the computer aided process planning (CAPP) stage in the production of high quality goods with tight tolerances by a variety of machining operations, and in the adaptive control of automated machine tools. With the known boundaries of surface roughness and machining conditions, machining could be performed with a relatively high rate of success with the selected machining conditions.6 ConclusionsThe investigations of this study indicate that the parameters cutting speed, feed, radial rake angle and nose radius are the primary actors influencing the surface roughness of medium carbon steel uring end milling. The approach presented in this paper provides n impetus to develop analytical models, based on experimental results for obtaining a surface roughness model using the response surface methodology. By incorporating the cutter geometry in the model, the validity of the model has been enhanced. The optimization of this model using genetic algorithms has resulted in a fairly useful method of obtaining machining parameters in order to obtain the best possible surface quality.中文翻译选择最佳工具，几何形状和切削条件利用表面粗糙度预测模型端铣摘要：刀具几何形状对工件表面质量产生的影响是人所共知的，因此，任何成型面端铣设计应包括刀具的几何形状。
成组技术外文文献翻译、机械加工工艺方面外文翻译、中英文翻译
成组技术外文文献翻译、机械加工工艺方面外文翻译、中英文翻译外文原文：Group TechnologyGroup technology GT is a very important methodology in today’s manufacturing significant. The reason for this is that group technology, when utilized to its fullest extent, can affect most areas of manufacturing, including design, process planning, scheduling, routing, factory layout, procurement, quality assurance, machine tool utilization, tool design, producibility engineering, and assembly.1 IntroductionGroup technology is a simple concept that is used widely in various forms. For a variety of reasons, it is logical to collect and associate things based on features that they have in common. This approach is familiar to everyone for plants, animals, and chemicals. Such organizational structures have also been used for hardware and other obviously similar products within the manufacturing world. Group technology represents structured categorization of particular value to the manufacturing community. It is already widely used; perhaps 50% of manufacturing companies use some form of GT.Bath or lot production suffers from many inefficiencies due to part variety and the general-purpose nature flexibility requirements of machine tools in use on the shop floor. In fact, a Cincinnati Milacron study showed that 95% of the time a part spends on the shop floor is idle time, the other 5% is divided between setup and teardown of the machine tool. The future breakdown of the 5% of on-machine time was developed by Dunlap. Based on this estimate, only 24% of the 5% is time which actually involves cutting; i.e., parts are being machined during only 1.2% of the total time spent in manufacturing. Group technology makes possible the application of several methods of analysis which assist in making batch production more efficient by reducing part variety via part families and improving throughout and work-in-process inventory. It is for this reason that group technology is becoming a key concept in manufacturing.2 DefinitionManufacturing philosophy to some, fundamental building block for more efficient production to most, group technology is a simple concept which utilizes/exploits similarities for more efficient production in bath manufacturing. Group technology usually classifies parts in the form of a code which is assigned to each part based on its shape or production processing characteristics. In use, coding parts assists in the control of planning and processing. This added control, which exploits similarities, leads to economies in the overall manufacturing process.The actual operator on the shop floor may never know this code, but designers, engineers, and planners find it an invaluable tool, allowing them to do more productive and useful analysis.3 General BenefitsIn practice, group technology is really nothing more than an information/indexing system. However, because of its focus on part design and processing similarities, analysis is possible which creates manufacturing economies of scale, encourages standardization, and eliminates duplication in design and process planning.Mass production enjoys the benefits of what are called economies of scale. Economies of scale achieved by processing a large number of parts over the same workstations or equipment. This result in less labor per part, more efficient machine utilization, and a faster turnover of inventory. Batch production in the past has not enjoyed economies of scale because of the need to remain flexible for changing part types and products. However, by grouping parts into families based on their similarities, much of the manufacturing processing of these parts can be done on entire families. This increases the number of parts processed with the same equipment conditions, thereby permitting some of the economies of scale of mass production.Standardization is achieved in both design and part process planning. Essentially, group technology creates an efficient design retrievalsystem since parts have been code based on shape. Similar design are located quickly and aspects such as part tolerances and producibility can be better understood, more easily applied, and kept more consistent from design to design. When standardized process planes are developed and include in the group technology code, new parts and repeat orders can follow similar processing routes through the shop floor, simplifying scheduling and flow through the shop.Group technology eliminates duplication. In both design and process planning, there is much les “reinventing of the wheel” since there is sufficient retrieval of standard designs and process plans.4 Application of GT in Process PlanningAlthough many areas of business operation can benefit from GT, manufacturing, the original application area, continues to be the place where GT is most widely practiced. Two important tasks in manufacturing planning and manufacturing engineering are scheduling and process planning. Job scheduling sets the order in which parts should be processed and can determine expected completion times for operation and orders. Process planning, on the other hand, decides the sequence of machines to which a part should be routed when it is manufactured and the operations that should be performed at each machine. Process planning also encompasses tool, jig, and fixture selection as well as documentation of the time standards run and setup time associated with each operation.Process planning can directly affect scheduling efficiency and, thus, many of the performance measures normally associated with manufacturing planning and control.Some of the largest productivity gains have been reported in the creation of process plans that determine how a part should be produced. With computer-aided process planning CAPP and GT it is possible to standardize such plans, reduce the number of new ones, and store, retrieve, edit, and print them out very efficiently.Process planning normally is not a formal procedure. Each time a new part is designed, a process planner will look at the drawing and decide which machine tools should process the parts, which operations should be performed, and in what sequenceThere are two reasons why companies often generate excess process plans. First, most companies have several planners, and each may come up with a different process plan for the very same part, Second, process; planning is developed with the existing configuration of machine tools in mind. Over time, the addition of new equipment will change the suitability of existing plans. Rarely are alterations to old process plans made. One company reportedly had 477 process plans developed for 523 different gears. A close look revealed that more than 400 of the plans could be eliminated. Process planning using CAPP can avoid these problems.Process planning with CAPP takes two different forms;With variant-based planning, one standardized plan and possibly one or more alternate plans is created and stored for each part family. When the planner enters the GT code for a part, the computer will retrieve the best process plan. If none exists, the computer will search for routings and operations for similar parts. The planner can edit the scheme on the CRT screen before printout.With generative planning, which can but does not necessarily rely on coded and classified parts, the computer forms the process plan through a series of questions the computer poses on the screen. The end product is also a standardized process plan, which is the best plan for a particular part.The variant-based approach relied on established plans entered into the computer memory, while the generative technique creates the process plans interactively, relying on the same logic and knowledge that a planner has. Generative process planning is much more complex than variant-based planning; in fact, it approaches the art of artificial intelligence. It is also much more flexible; by simply changing the planning logic, for instance, engineers can consider the acquisition of a new machine tool. With the variant-based method, the engineers must look over and possibly correct all plans that the new tool might affect.CAPP permits creation and documentation of process plans in a fraction of the time it would take a planner to do the work manually and vastlyreduces the number of errors and the number of new plans that must be stored. When you consider that plans normally are handwritten and that process planners spend as much as 30% of their time preparing them, CAPP’S contribution of standardized formats for plans and more readable documents is important. CAPP, in effect, functions as advanced text editor. Furthermore, it can be linked with an automated standard data system that will calculate and record the run times and the setup times for each operation.CAPP can lead to lower unit costs through production of parts in an optimal way. That is, cost savings come not only via more efficient process planning but also through reduced labor, material, tooling, and inventory costs.GT can help in the creation of programs that operate numerically NC machinery, n area related to process planning. For example, after the engineers at Otis Engineering had formed part families and cells, the time to produce a new NC tape dropped from between 4 and 8 hours to 30 minutes. The company thereby improved the potential for use of NC equipment on batches with small manufacturing quantities.编者：吴非晓等《机械英语2》外语教学与研究出版社2002.7译文：成组技术在当今的制造环境下，尤其是对批量生产来说，成组技术（GT）是一个很重要的生产方式而且它正变得越来越重要。
机械专业毕业设计外文翻译--工艺规程制订
附录Process PlanningThe product design is the plan for the product and its components and subassemblies.To convert the product design into a physical entity ,a manufacturing plan is needed .The activity of developing such a plan is called process planning .It is the link between product design and manufacturing .Process planning involves determining the sequence of processing and assembly steps that must be accomplished to make the product .In the present chapter ,we examine processing planning and several related topics.At the outset ,we should distinguish between process planning and production planning ,which is covered in the following chapter. Process planning is concerned with the engineering and technological issues of how to make the products and its parts. What types of equipment and tooling are required to fabricate the parts and assemble the product ? Production planning is concerned with the logistics of making the product .After process planning is concerned with ordering the materials and obtaining the resources required to make the product in sufficient quantities to satisfy demand for it.Process PlanningProcess planning involves determining the most appropriate manufacturing and assembly processes and the sequence in which they should be accomplished to produce a given part or product according to specifications set forth in the product design documentation.The scope and variety of processes that can be planned are generally limited by the available processing equipment and technological capabilities of the company of plant .Parts that cannot be made internally must be purchased from outside vendors. It should be mentioned that the choice of processes is also limited by the details of the product design.This is apoint we will return to later.Process planning is usually accomplished by manufacturing engineers .(Other titles include in industrial engineer.) The process planner must be familiar with the particular manufacturing processes available in the factory and be able to interpret engineering drawings .Based on the planner’s knowledge,skill,and experience ,the processing steps are developed in the most logical sequence to make each part .Following is a list of the many decisions and details usually include within the scope of process planning :.Interpretation of design drawings.The part of product design must be analyzed (materials,dimensions,tolerances ,surface finished,etc.) at the start of the process planning procedure..Process and sequence.The process planner must select which processes are required and their sequence.A brief description of processing steps must be prepared..Equipment selection . In general , process planners must develop plans that utilize existing equipment in the plant .Otherwise ,the component must be purchased ,or an investment must be made in new equipment ..Tools ,dies,molds,fixtures,and gages.The process must decide what tooling is required for each processing step.The actual design and fabrication of these tools is usually delegated to a tool design department and tool room ,or an outside vendor specializing in that type of tool is contacted.Methods analysis .Workplace layout ,small tools ,hoists for lifting heavy parts ,even in some cases hand and body motions must be specified for manual operations .The industrial engineering department is usually responsible for this area..Work standards.Work measurement techniques are used to set time standards for each operation ..Cutting tools and cutting conditions.These must be specified for machiningoperations ,often with reference to standard handbook recommendations.Process Planning for partsFor individual parts,the processing sequence is documented on a form called a route sheet .(Not all companies use the name route sheet ;another name is “operation sheet .”)Just as engineering drawings are used to specify the product design ,route sheets are used to specify the process plan .They are counterparts,one for product design ,the other for manufacturing .A typical route sheet ,illustrated in Fig.21.1,includes the following information: (1) all operations to be performed on the work part ,listed in the order in which they should be performed ; (2) a brief description of each operation indicating the processing to be accomplished,with references to dimensions and tolerances on the part drawing; (3) the specific machines on which the work to be done; and (4) special tooling such as dies molds ,cutting tools,jigs or fixtures ,and gages.Some companies also include setup times ,cycle time standards,and other data.It is called a route sheet because the processing sequence defines the route that the part must follow in the factory .Some of the guidelines in preparing a route sheet are listed in Table 21-1.Decisions on process to be used to fabricate a given part are based largely on the starting material for the part .This starting material is selected by the product designer.Once the material has been specified ,the range of the possible processing operation is reduced considerably .The product designer’s decisions on starting material are based primarily on functional requirements ,although economics and manufacturability a role in the selection.A typical processing sequence to fabricate an individual part consists of : (1) a basic process,(2)secondary processes ,(3) operations to enhance physical properties,and (4)finishing operations.The sequence is shown in Fig.21.2. A basic process determines the starting geometry of the workpart.Metal casting ,plastic molding ,and roling of sheet metal are examples of basic processes.The starting geometry must often be refined by secondaryprocesses,operations that transform the starting geometry (or close to final geometry ).The secondary geometry processes that might be used are closely correlated to the basic process that provides the starting geometry.When sand casting is the basic processes,machining operations are generally the second processes .When a rolling mill produces sheet metal,stamping operations such as punching and bending are the secondary processes.When plastic injection molding is the basic process ,secondary operations are often unnecessary,because most of the geometric features that would otherwise require machining can be created by the molding operation.Plastic molding and other operation that require no subsequent secondary processing are called net shape processes.Operations that require some but not much secondary processing (usually machining ) are referred to as near net shape processes.Some impression die forgings are in this category .These parts can often be shaped in the forging operation(basic processes)so that minimal machining (secondary processing )is required .Once the geometry has been established ,the next step for some parts is to improve their mechanical and physical properties .Operations to enhance properties do not alter the geometry of the part;instead,they alter physical properties .Heat treating operations on metal parts are the most common examples .Similar heating treatments are performed on glass to produce tempered glass.For most manufactured parts ,these property-enhancing operations are not required in the processing sequence ,as indicated by the alternative arrow path in Fig.21.2.Finally finish operations usually provide a coat on the work parts (or assembly )surface. Examples inclued electroplating ,thin film deposition techniques ,and painting.The purpose of the coating is to enhance appearance ,change color ,or protect the surface from corrosion,abrasion ,and so forth .Finishing operations are not required on many parts ;for example, plastic molding rarely require finishing .When finishing is required ,it is usuallythe final step in the processing sequence .Table 21-2 presents some typical processing sequences for common materials used in manufacturing .In most cases,parts and materials arriving at the factory have complete their basic process.Thus ,the first operation in the process plan follows the basic process that has provided the starting geometry of the part ..For example ,machined parts begain as bar stock or castings or forgings,which are purchased from outide vendors.The process plan begains with the machining operations in the company’s own plant .Stempings begin as sheet metal coils or strips that are bought from the rolling mill.These raw materials are supplied outside sources so that the secondary processes,property-enhancing operations ,and finishing operatios can be performed in the company’s own factory.In addition to the route sheet ,a more detailed description of eac operation is usually prepared. This is filed in the particular production department office where the operation is performed.It lists specific details of the operation ,such as cutting conditionsand toolings(if the operation is machining )and other instructions that may be useful to the amchine operator.The desciptions often include sketches of the machine setup.Processing Planning for AssembliesThe type of assembly method used for a given product depends on factors such as : (1) the anticipated production quantities ;(2) complexity of the assembled product ,for example ,the number of distinct components ;and (3)assembly processes used ,for example ,mechanical assembly versus welding .For a product that is to be made in relatively small quantities ,assembly is usually performed on manual assembly lines .For simple products of a dozen or so components,to be made in large quantities ,automated assembly systems are appropriate .In any case ,there is a precedence order in which the work must be accomplished .The precedence requirements are sometimes portrayed graphically on a precedence diagram.Process planning for assembly involves development of assembly instructions,but in more detail .For low production quantities,the entire assembly is completed at a single station .For high production on an assembly line ,process planning consists of allocating work elements to the individual stations of the line, a procedure called line balancing.The assembly line routes the work unit to individual stations in the proper order as determined by the line balance solution.As in process planning for individual components ,any tools and fixtures required to accomplish an assembly task must be determined ,designed,and built;and the workstation arrangement must belaid out.工艺规程制订产品设计是用于产品,及它的部件装配的计划. 为了把产品设计转换成一个实际物体 ,这需要一个制造计划。
外文翻译Numerically Controlled (NC) Machines
本科生毕业设计（论文）外文翻译毕业设计（论文）题目：剪叉式物流液压升降台外文题目：Numerically Controlled (NC) Machines译文题目：数控机床学生姓名：张龙专业：机械设计制造及其自动化指导教师姓名：张凯评阅日期：正文内容小四号字，宋体，行距1.5倍行距。
Numerically Controlled (NC) MachinesWith automatics, programming is expensive and can be justified only for long production runs. However, with machines incorporating feedback control, programs can be provided in the form of punched tapes or punched cards, which are relatively inexpensive to produce compared with disc and drum cams. These machines are known as numerically controlled (NC) machines and can be used economically in small-batch production.As the name implies, numerical control involves control on the basis of numerical information that specifies the relative position of the tool and workpiece. From the block diagram for a machine-tool control system in Fig. 12 it can be seen that two essential elements are added to an otherwise standard machine.The first added element is a means of driving the machine table or toolholder by a servomotor, and hence the motion of the tool or workpiece depends on the signal passed to the servomotor. The second added element is a transducer that continuously monitors the position of the tool or workpiece. The signal from the transducer is compared with that obtained from the tape, and any difference (or error) is converted to analog form, amplified, and used to drive the servomotor until the tool or workpiece position agrees with the position specified by the information on the tape.Fig. 12: Feedback loop for one axis of a machine-tool control system There are two basic types of NC systems: the point-to-point, or positioning, system and the continuous-path, or contouring, system. The point-to-point system would be applied, for example, to a vertical-drilling machine. If control of the two horizontal-motion axes of the table supporting the workpiece is arranged, the machine can be programmed to locate and then drill a specified pattern of holes. In the point-to-point system the path of the tool relative to the workpiece between holes is not important, and only the coordinates of the end point of each motion of the table are specified. The continuous-path system would be applied, for example, to a vertical-milling machine that was required to end mill a complicated shape, such as cam or pocket in a workpiece. In the continuous-path system the position of the tool relative to the workpiece must be continuously controlled while workpieces are being machined.With continuous-path, or contouring, systems the position of the tool relative to the workpiece is specified by a series of coordinates, and the control system is designed to follow a path between these points by interpolation. Some machines follow a straight-line path (linear interpolation); others follow a curved path (circular or parabolic interpolation).Numerical control can be applied to motions along or about any axis,·but two or three-axis control systems are the most common. In general, vertical-milling machines and lathes utilize continuous-path, or contouring control. Vertical-drilling machines jig borers, and small milling machines often use positional control.One sophisticated form of NC machine is known as the machining center. This machine is generally a vertical-milling machine with several axes of control and with automatic tool-changing facilities. The tools are usually held in a rotary magazine, and tool changes are commanded by the punched tape. Thus, with a machining center a complicated workpiece can be completely machined on all faces except the base through a combination of milling, drilling, boring, facing, reaming, and tapping operations. This type of system is therefore most suitable for the batch production of main components.A further refinement of numerical control is adaptive control. This type of system can adapt itself to the prevailing circumstances. These circumstances are measured by the system itself and might include the power required for the machining operation, the wear of the cutting tool or grinding wheel, the forces generated, or the onset of chatter or instability. The system ideally would be designed for automatic adjustment of the feed, speed, or tool position to produce components at minimum cost and within the tolerance specified. Such a system would be very expensive and has not yet found wide application.A relatively simple adaptive control system would automatically vary the cutting speed and feed in such a way as to maximize metal-removal rates without exceeding predetermined cutting forces and power consumption. Systems of this type are relatively inexpensive and can machine under near-optimum conditions.数控机床伴随着自动化产生，只有在长期的生产运行中，编程的价格很昂贵，同时又是合理的。
机械工程专业毕业设计外文翻译
英文原文名Lthes中文译名车床10/ 1中文译文：车床车床主要是为了进行车外圆、车端面和镗孔等项工作而设计的机床。
车削很少在其他种类的机床上进行，而且任何一种其他机床都不能像车床那样方便地进行车削加工。
由于车床还可以用来钻孔和铰孔，车床的多功能性可以使工件在一次安装中完成几种加工。
因此，在生产中使用的各种车床比任何其他种类的机床都多。
车床的基本部件有：床身、主轴箱组件、尾座组件、溜板组件、丝杠和光杠。
床身是车床的基础件。
它能常是由经过充分正火或时效处理的灰铸铁或者球墨铁制成。
它是一个坚固的刚性框架，所有其他基本部件都安装在床身上。
通常在床身上有内外两组平行的导轨。
有些制造厂对全部四条导轨都采用导轨尖朝上的三角形导轨（即山形导轨），而有的制造厂则在一组中或者两组中都采用一个三角形导轨和一个矩形导轨。
导轨要经过精密加工以保证其直线度精度。
为了抵抗磨损和擦伤，大多数现代机床的导轨是经过表面淬硬的，但是在操作时还应该小心，以避免损伤导轨。
导轨上的任何误差，常常意味着整个机床的精度遭到破坏。
主轴箱安装在内侧导轨的固定位置上，一般在床身的左端。
它提供动力，并可使工件在各种速度下回转。
它基本上由一个安装在精密轴承中的空心主轴和一系列变速齿轮(类似于卡车变速箱)所组成。
通过变速齿轮，主轴可以在许多种转速下旋转。
大多数车床有8~12种转速，一般按等比级数排列。
而且在现代机床上只需扳动2~4个手柄，就能得到全部转速。
一种正在不断增长的趋势是通过电气的或者机械的装置进行无级变速。
由于机床的精度在很大程度上取决于主轴，因此，主轴的结构尺寸较大，通常安装在预紧后的重型圆锥滚子轴承或球轴承中。
主轴中有一个贯穿全长的通孔，长棒料可以通过该孔送料。
主轴孔的大小是车床的一个重要尺寸，因此当工件必须通过主轴孔供料时，它确定了能够加工的棒料毛坯的最大尺寸。
数字控制的机器比人工操纵的机器精度更高、生产出零件的一致性更好、生产速度更快、而且长期的工艺装备成本更低。
切削技术-加工基础外文文献翻译、中英文翻译
外文资料CUTTING TECHNOLOGYIntroduction of MachiningMachining as a shape-producing method is the most universally used and the most important of all manufacturing processes. Machining is a shape-producing process in which a power-driven device causes material to be removed in chip form. Most machining is done with equipment that supports both the work piece and cutting tool although in some cases portable equipment is used with unsupported workpiece.Low setup cost for small Quantities. Machining has two applications in manufacturing. For casting, forging, and press working, each specific shape to be produced, even one part, nearly always has a high tooling cost. The shapes that may he produced by welding depend to a large degree on the shapes of raw material that are available. By making use of generally high cost equipment but without special tooling, it is possible, by machining; to start with nearly any form of raw material, so tong as the exterior dimensions are great enough, and produce any desired shape from any material. Therefore .machining is usually the preferred method for producing one or a few parts, even when the design of the part would logically lead to casting, forging or press working if a high quantity were to be produced.Close accuracies, good finishes. The second application for machining is based on the high accuracies and surface finishes possible. Many of the parts machined in low quantities would be produced with lower but acceptable tolerances if produced in high quantities by some other process. On the other hand, many parts are given their general shapes by some high quantity deformation process and machined only on selected surfaces where high accuracies are needed. Internal threads, for example, are seldom produced by any means other than machining and small holes in press worked parts may be machined following the press working operations.Primary Cutting ParametersThe basic tool-work relationship in cutting is adequately described by means of four factors: tool geometry, cutting speed, feed, and depth of cut.The cutting tool must be made of an appropriate material; it must be strong, tough, hard, and wear resistant. The tool s geometry characterized by planes and angles, must be correct for each cutting operation. Cutting speed is the rate at which the work surface passes by the cutting edge. It may be expressed in feet per minute.For efficient machining the cutting speed must be of a magnitude appropriate to the particular work-tool combination. In general, the harder the work material, the slower the speed.Feed is the rate at which the cutting tool advances into the workpiece. "Where the workpiece or the tool rotates, feed is measured in inches per revolution. When the tool or the work reciprocates, feed is measured in inches per stroke, Generally, feed varies inversely with cutting speed for otherwise similar conditions.The depth of cut, measured inches is the distance the tool is set into the work. It is the width of the chip in turning or the thickness of the chip in a rectilinear cut. In roughing operations, the depth of cut can be larger than for finishing operations.The Effect of Changes in Cutting Parameters on Cutting TemperaturesIn metal cutting operations heat is generated in the primary and secondary deformation zones and these results in a complex temperature distribution throughout the tool, workpiece and chip. A typical set of isotherms is shown in figure where it can be seen that, as could be expected, there is a very large temperature gradient throughout the width of the chip as the workpiece material is sheared in primary deformation and there is a further large temperature in the chip adjacent to the face as the chip is sheared in secondary deformation. This leads to a maximum cutting temperature a short distance up the face from the cutting edge and a small distance into the chip.Since virtually all the work done in metal cutting is converted into heat, it could be expected that factors which increase the power consumed per unit volume of metal removed will increase the cutting temperature. Thus an increase in the rake angle, all otherparameters remaining constant, will reduce the power per unit volume of metal removed and the cutting temperatures will reduce. When considering increase in unreformed chip thickness and cutting speed the situation is more complex. An increase in undeformed chip thickness tends to be a scale effect where the amounts of heat which pass to the workpiece, the tool and chip remain in fixed proportions and the changes in cutting temperature tend to be small. Increase in cutting speed; however, reduce the amount of heat which passes into the workpiece and this increase the temperature rise of the chip m primary deformation. Further, the secondary deformation zone tends to be smaller and this has the effect of increasing the temperatures in this zone. Other changes in cutting parameters have virtually no effect on the power consumed per unit volume of metal removed and consequently have virtually no effect on the cutting temperatures. Since it has been shown that even small changes in cutting temperature have a significant effect on tool wear rate it is appropriate to indicate how cutting temperatures can be assessed from cutting data.The most direct and accurate method for measuring temperatures in high -speed-steel cutting tools is that of Wright &. Trent which also yields detailed information on temperature distributions in high-speed-steel cutting tools. The technique is based on the metallographic examination of sectioned high-speed-steel tools which relates microstructure changes to thermal history.Trent has described measurements of cutting temperatures and temperature distributions for high-speed-steel tools when machining a wide range of workpiece materials. This technique has been further developed by using scanning electron microscopy to study fine-scale microstructure changes arising from over tempering of the tempered martens tic matrix of various high-speed-steels. This technique has also been used to study temperature distributions in both high-speed -steel single point turning tools and twist drills.Wears of Cutting ToolDiscounting brittle fracture and edge chipping, which have already been dealt with, tool wear is basically of three types. Flank wear, crater wear, and notch wear. Flank wear occurs on both the major and the minor cutting edges. On the major cutting edge, which is responsible for bulk metal removal, these results in increased cutting forces and highertemperatures which if left unchecked can lead to vibration of the tool and workpiece and a condition where efficient cutting can no longer take place. On the minor cutting edge, which determines workpiece size and surface finish, flank wear can result in an oversized product which has poor surface finish. Under most practical cutting conditions, the tool will fail due to major flank wear before the minor flank wear is sufficiently large to result in the manufacture of an unacceptable component.Because of the stress distribution on the tool face, the frictional stress in the region of sliding contact between the chip and the face is at a maximum at the start of the sliding contact region and is zero at the end. Thus abrasive wear takes place in this region with more wear taking place adjacent to the seizure region than adjacent to the point at which the chip loses contact with the face. This result in localized pitting of the tool face some distance up the face which is usually referred to as catering and which normally has a section in the form of a circular arc. In many respects and for practical cutting conditions, crater wear is a less severe form of wear than flank wear and consequently flank wear is a more common tool failure criterion. However, since various authors have shown that the temperature on the face increases more rapidly with increasing cutting speed than the temperature on the flank, and since the rate of wear of any type is significantly affected by changes in temperature, crater wear usually occurs at high cutting speeds.At the end of the major flank wear land where the tool is in contact with the uncut workpiece surface it is common for the flank wear to be more pronounced than along the rest of the wear land. This is because of localised effects such as a hardened layer on the uncut surface caused by work hardening introduced by a previous cut, an oxide scale, and localised high temperatures resulting from the edge effect. This localised wear is usually referred to as notch wear and occasionally is very severe. Although the presence of the notch will not significantly affect the cutting properties of the tool, the notch is often relatively deep and if cutting were to continue there would be a good chance that the tool would fracture.If any form of progressive wear allowed to continue, dramatically and the tool would fail catastrophically, i. e. the tool would be no longer capable of cutting and, at best, theworkpiece would be scrapped whilst, at worst, damage could be caused to the machine tool. For carbide cutting tools and for all types of wear, the tool is said to have reached the end of its useful life long before the onset of catastrophic failure. For high-speed-steel cutting tools, however, where the wear tends to be non-uniform it has been found that the most meaningful and reproducible results can be obtained when the wear is allowed to continue to the onset of catastrophic failure even though, of course, in practice a cutting time far less than that to failure would be used. The onset of catastrophic failure is characterized by one of several phenomena, the most common being a sudden increase in cutting force, the presence of burnished rings on the workpiece, and a significant increase in the noise level.Mechanism of Surface Finish ProductionThere are basically five mechanisms which contribute to the production of a surface which have been machined. These are:1、The basic geometry of the cutting process. In, for example, single point turning the tool will advance a constant distance axially per revolution of the workpiecc and the resultant surface will have on it, when viewed perpendicularly to the direction of tool feed motion, a series of cusps which will have a basic form which replicates the shape of the tool in cut.2、The efficiency of the cutting operation. It has already been mentioned that cutting with unstable built-up-edges will produce a surface which contains hard built-up-edge fragments which will result in a degradation of the surface finish. It can also be demonstrated that cutting under adverse conditions such as apply when using large feeds small rake angles and low cutting speeds, besides producing conditions which lead to unstable built-up-edge production, the cutting process itself can become unstable and instead of continuous shear occurring in the shear zone, tearing takes place, discontinuous chips of uneven thickness are produced, and the resultant surface is poor. This situation is particularly noticeable when machining very ductile materials such as copper and aluminum.3、The stability of the machine tool. Under some combinations of cutting conditions; workpiece size, method of clamping ,and cutting tool rigidity relative to the machine tool structure, instability can be set up in the tool which causes it to vibrate. Under someconditions this vibration will reach and maintain steady amplitude whilst under other conditions the vibration will built up and unless cutting is stopped considerable damage to both the cutting tool and workpiece may occur. This phenomenon is known as chatter and in axial turning is characterized by long pitch helical bands on the workpiece surface and short pitch undulations on the transient machined surface. M4、The effectiveness of removing swarf. In discontinuous chip production machining, such as milling or turning of brittle materials, it is expected that the chip (swarf) will leave the cutting zone either under gravity or with the assistance of a jet of cutting fluid and that they will not influence the cut surface in any way. However, when continuous chip production is evident, unless steps are taken to control the swarf it is likely that it will impinge on the cut surface and mark it. Inevitably, this marking besides looking5、The effective clearance angle on the cutting tool. For certain geometries of minor cutting edge relief and clearance angles it is possible to cut on the major cutting edge and burnish on the minor cutting edge. This can produce a good surface finish but, of course, it is strictly a combination of metal cutting and metal forming and is not to be recommended as a practical cutting method. However, due to cutting tool wear, these conditions occasionally arise and lead to a marked change in the surface characteristics.Limits and TolerancesMachine parts are manufactured so they are interchangeable. In other words, each part of a machine or mechanism is made to a certain size and shape so will fit into any other machine or mechanism of the same type. To make the part interchangeable, each individual part must be made to a size that will fit the mating part in the correct way. It is not only impossible, but also impractical to make many parts to an exact size. This is because machines are not perfect, and the tools become worn. A slight variation from the exact size is always allowed. The amount of this variation depends on the kind of part being manufactured. For examples part might be made 6 in. long with a variation allowed of 0.003 (three-thousandths) in. above and below this size. Therefore, the part could be 5.997 to 6.003 in. and still be the correct size. These are known as the limits. The difference between upper and lower limits is called the tolerance.A tolerance is the total permissible variation in the size of a part.The basic size is that size from which limits of size arc derived by the application of allowances and tolerances.Sometimes the limit is allowed in only one direction. This is known as unilateral tolerance.Unilateral tolerancing is a system of dimensioning where the tolerance (that is variation) is shown in only one direction from the nominal size. Unilateral tolerancing allow the changing of tolerance on a hole or shaft without seriously affecting the fit.When the tolerance is in both directions from the basic size it is known as a bilateral tolerance (plus and minus).Bilateral tolerancing is a system of dimensioning where the tolerance (that is variation) is split and is shown on either side of the nominal size. Limit dimensioning is a system of dimensioning where only the maximum and minimum dimensions arc shown. Thus, the tolerance is the difference between these two dimensions.Surface Finishing and Dimensional ControlProducts that have been completed to their proper shape and size frequently require some type of surface finishing to enable them to satisfactorily fulfill their function. In some cases, it is necessary to improve the physical properties of the surface material for resistance to penetration or abrasion. In many manufacturing processes, the product surface is left with dirt .chips, grease, or other harmful material upon it. Assemblies that are made of different materials, or from the same materials processed in different manners, may require some special surface treatment to provide uniformity of appearance.Surface finishing may sometimes become an intermediate step processing. For instance, cleaning and polishing are usually essential before any kind of plating process. Some of the cleaning procedures are also used for improving surface smoothness on mating parts and for removing burrs and sharp corners, which might be harmful in later use. Another important need for surface finishing is for corrosion protection in a variety of: environments. The type of protection procedure will depend largely upon the anticipated exposure, with dueconsideration to the material being protected and the economic factors involved.Satisfying the above objectives necessitates the use of main surface-finishing methods that involve chemical change of the surface mechanical work affecting surface properties, cleaning by a variety of methods, and the application of protective coatings, organic and metallic.In the early days of engineering, the mating of parts was achieved by machining one part as nearly as possible to the required size, machining the mating part nearly to size, and then completing its machining, continually offering the other part to it, until the desired relationship was obtained. If it was inconvenient to offer one part to the other part during machining, the final work was done at the bench by a fitter, who scraped the mating parts until the desired fit was obtained, the fitter therefore being a 'fitter' in the literal sense. J It is obvious that the two parts would have to remain together, and m the event of one having to be replaced, the fitting would have to be done all over again. In these days, we expect to be able to purchase a replacement for a broken part, and for it to function correctly without the need for scraping and other fitting operations.When one part can be used 'off the shelf' to replace another of the same dimension and material specification, the parts are said to be interchangeable. A system of interchangeability usually lowers the production costs as there is no need for an expensive, 'fiddling' operation, and it benefits the customer in the event of the need to replace worn parts.Automatic Fixture DesignTraditional synchronous grippers for assembly equipment move parts to the gripper centre-line,assuring that the parts will be in a known position after they arc picked from a conveyor or nest. However, in some applications, forcing the part to the centre-line may damage cither the part or equipment. When the part is delicate and a small collision can result in scrap, when its location is fixed by a machine spindle or mould, or when tolerances are tight, it is preferable to make a gripper comply with the position of the part, rather than the other way around. For these tasks, Zaytran Inc. Of Elyria, Ohio, has created the GPNseries of non- synchronous, compliant grippers. Because the force and synchronizations systems of the grippers are independent, the synchronization system can be replaced by a precision slide system without affecting gripper force. Gripper sizes range from 51b gripping force and 0.2 in. stroke to 40Glb gripping force and 6in stroke.GrippersProduction is characterized by batch-size becoming smaller and smaller and greater variety of products. Assembly, being the last production step, is particularly vulnerable to changes in schedules, batch-sizes, and product design. This situation is forcing many companies to put more effort into extensive rationalization and automation of assembly that was previously the case. Although the development of flexible fixtures fell quickly behind the development of flexible handling systems such as industrial robots, there are, nonetheless promising attempts to increase the flexibility of fixtures. The fact that fixtures are the essential product - specific investment of a production system intensifies the economic necessity to make the fixture system more flexible.Fixtures can be divided according to their flexibility into special fixtures, group fixtures, modular fixtures and highly flexible fixtures. Flexible fixtures are characterized by their high adaptability to different workpieces, and by low change-over time and expenditure.Flexible fixtures with form variability are equipped with variable form elements (e. g. needle - cheek, multileaf, and lamella - cheek), modular workpiece nonspecific holding or clamping - elements (e. g. , pneumatic modular holding - fixtures and fixtures kits with moveable elements), or with fictile and hardening media(e.g. ,panic late- fluidized - bed - fixtures and thermal clamping - fixtures).Independent of the flexibility of a fixture, there are several steps required to generate a fixture, in which a workpiece is fixed for a production task. The first step is to define the necessary position of the workpiece in the fixture, based on the unmachined or base pan, and the working features. Following this, a combination of stability planes must be selected. These stability planes constitute the fixture configuration in which the workpiece is fixed in the defined position, all the forces or torques are compensated, and the necessary access tothe working features is ensured. Finally, the necessary positions of moveable or modular fixture elements must be calculated- adjusted, or assembled, so that the workpiece is firmly fixed in the fixture. Through such a procedure the planning and documentation of the configuration and assembly of fixture can be automated.The configuration task is to generate a combination of stability planes, such that fixture forces in these planes will result in workpiece and fixture stability. This task can be accomplished conventionally, interactively or in a nearly fully automated manner. The advantages of an interactive or automated configuration determination are a systematic fixture design process, a reduction of necessary designers, a shortening of lead time and better match to the working conditions. In short, a significant enhancement of fixture productivity and economy can be achieved.With the full preparation of construction plans and a bill of materials, t time saving of up to 60% in achieving the first assembly can be realized. Hence, an aim of the fixture configuration process is the generation of appropriate documents.The following sections will describe a program procedure for automated fixture design and an application example.中文译文切削技术加工基础作为产生形状的一种方法，机械加工是所有制造过程中最普遍使用的而且是最重要的方法。
毕业论文的外文翻译是什么
毕业论文的外文翻译是什么在如今全球化的时代，毕业论文的外文翻译变得越来越重要。
由于不同学术领域与研究主题在全球范围内的广泛交流，外文文献往往成为毕业论文写作的重要参考资源。
毕业论文的外文翻译不仅能够扩充研究数据来源，还能加深理解并对比国内外研究现状以提升研究质量。
本文将探讨毕业论文的外文翻译的定义、目的以及相关注意事项。
外文翻译的定义和目的毕业论文的外文翻译是指将英语、法语、德语、俄语或其他外文献的内容翻译成中文的过程。
它的目的是使学术研究者能够更好地理解和应用外文文献，以支撑他们的研究工作。
通过对外文献的翻译，学术界可以顺利进行国际交流与合作，拓宽知识视野。
研究者也能为毕业论文提供全球范围内的最新研究成果，提高论文的学术水平。
注意事项在进行毕业论文的外文翻译时，以下几个注意事项应牢记于心：1.准确性和可信性：翻译的准确性和可信性是首要关注的问题。
翻译者必须确保所翻译的内容与原文的意思保持一致，并尽量使用准确和专业的词汇。
对于生僻词汇或特定领域的术语，可以借助专业工具或咨询相关领域的专家以确保翻译的准确性。
2.语言风格的调整：毕业论文的外文翻译需要根据中文写作的习惯和规范进行语言风格的调整。
例如，外文中可能使用了复杂的句子结构或文化隐喻，翻译时应尽量使用简明清晰的中文表达，以确保读者能够准确理解研究内容。
3.文化背景的融入：语言与文化密不可分。
在外文翻译过程中，翻译者需要了解原文所处的文化背景，并适当融入到翻译中。
这样才能确保翻译的内容在目标文化中具有更好的可读性和可理解性。
4.保护原文作者的权益：毕业论文的外文翻译要尊重并保护原文作者的权益。
在翻译时，应注明原文出处，以遵守学术诚信规范，并尽量避免篡改、删减或误解原文的意思。
如果有需要，可以适度加入个人的理解或注释，但必须清晰标注为个人观点。
5.翻译工具的利用：在进行毕业论文的外文翻译时，可以利用翻译工具辅助翻译。
然而，机器翻译并不能完全取代人工翻译的重要性。
毕业论文英文翻译要求（通用版）（范文模版）
毕业论文英文翻译要求（通用版）（范文模版）第一篇：毕业论文英文翻译要求(通用版)（范文模版）本科毕业设计（论文）英文翻译要求翻译的文章应与毕业设计课题或专业知识相关的文献，要求翻译1-2篇，合计中文字数不少于3000字。
外文翻译应包括：外文题目，作者、出版日期和出版社，翻译内容的起止页码，外文原文，然后是中文题目，作者、出版日期和出版社，中文翻译。
外文翻译所用的文献，应主要选自学术期刊或学术会议的文章，其次是教科书或其他书籍。
英文原文和翻译均作为毕业论文附录，同时给出英文原文的出处，如果是网上下载的原文请给出网址。
第二篇：毕业论文英文翻译武汉科技大学本科毕业设计外文翻译Automatic Statistical Process Control of a CNC Turning Centre Using Tool Offsets and Tool ChangeP.R.Gibson and K.HoangDepartment of Mechanical Engineering, University of Wollongong, Australia School of Mechanical and Manufacturing Engineering, University of New South Wales, Australia 数控车削中心刀补及换刀的自动统计过程控制P.R.Gibson and K.Hoang澳大利亚伍伦贡大学机械工程系，新威尔士大学机械制造工程学院武汉科技大学本科毕业设计外文翻译该论文涉及了自动统计过程控制（ASPC）在数控车削中刀补和换刀的自动周期测量上的运用。
由于当今制造对快速稳定的控制系统的需求，而且为了实现较高的产出率，一个闭环ASPC系统已被采用。
我们引入了自动周期测量技术，以全面测量该系统。
关键字：工艺规划；数控；车削简介今天，所有制造行业都面临着采用更加经济高效的质量控制系统，以满足客户的需求这一问题。
机械加工外文翻译、中英文翻译、机械类外文文献翻译
机械加工外文翻译、中英文翻译、机械类外文文献翻译The engine lathe is an old but still useful metal removal machine with many desirable attributes。
While it is no longer commonlyXXX。
In today's n shops。
it has largely been XXX。
turret lathes。
and automatic XXX of single-point tooling for maximum metal removal。
and the use of form tools for finished products that are on par with the fastest processing XXX.When it XXX for the engine lathe。
it largely depends on the skill of the operator。
Design XXX part for n。
it is XXX.XXX cutting tools。
XXX ns。
as the machine can perform these ns in one setup。
They are also capable of producing parts with high n and accuracy。
XXX industries.Now more than ever。
n machining XXX of a specific method。
the XXX.When designing for low quantities。
such as 100 or 200 parts。
it is most cost-effective to use a XXX。
designers should aim to minimize the number of ns required.Another n for n XXX。
外文翻译=从生态加工技术对攻丝的研究_大学论文
外文资料翻译译文从生态加工技术对攻丝的研究摘要这项研究是关于攻螺纹（扭矩，攻丝，磨损，工作硬度等）的加工特性。
在生态加工技术操作下，涂有TiN的MMC（铝合金金属复合材料）攻螺丝形成的攻丝得到了调查，并与没有涂层的特性进行了比较。
下面的结果就是从这份研究中得到的：1.TiN涂层攻丝的刀具寿命是没有攻丝的四倍；2.有TiN涂层的攻丝形成的螺纹比没有的加工硬化要低。
关键词：攻丝；攻螺丝；螺纹；生态加工；钻孔1．引言螺栓、螺钉机械连接中的螺纹是机械部件的最重要紧固系统之一。
螺纹制造有很多种方法，特别攻螺丝是用来生产内螺纹的有效的技术。
最近，每年都强调增加生产力。
据说现在的车间里，最重要和最严重的问题是提高生产力。
怎样改善孔加工（钻/铰孔和攻丝）已成为一个严重的问题。
传统的刀具材料限制了生产力的提高，如高速钢刀具加工铝合金金属复合材料（MMC）时刀具寿命很短由于碳化硅粒子的腐蚀天性。
因此，刀具的磨损和破坏阻碍了生产力的提高。
为了实现理想的生产力，攻丝已经吸引了车间工程师的注意。
在这项研究中，用攻丝加工MMC，利用攻丝（扭矩，攻丝磨损，工作硬度等）的切割特点，有TiN涂层和没有涂层的都进行了调查。
2. 实验方法2.1实验装置攻丝试验在辛辛那提5’NC-MC (5HP)进行。
该（钻孔和攻丝）仪器和数据采集系统如图2.1。
切削力（推力和扭矩）测定使用三个类型9273 压电电力测功器和相应的场所用5007电荷放大器放大。
得到的信号，然后传递到A / D转换器AZI-16-12 ，连接到个人电脑。
切削力测量安装如图2.2。
2.2工件，钻及塔在本实验中使用的工件是铝合金（2618 MMC）的增强，15％碳化硅颗粒。
形成无槽丝锥的螺纹是M10如图2.3和两种类型的攻丝被用来在调查过程中。
攻丝的形状类似于螺钉的形状（M10，孔距1.5），无论有没有氮化钛涂层。
定位孔的直径9.3mm，用于所有试验和聚晶金刚石攻丝钻孔（高速钢硬质合金碳化钨和聚晶金刚石钻孔）用在所有测试。
机械类英语论文及翻译
机械类英语论文及翻译 Prepared on 22 November 2020附录一:Mechanical DesignLiqingyu zhangjiaMachinery manufacturing equipment designAbstractA machine is a combination of mechanisms and other components which transforms, transmits. Examples are engines, turbines, vehicles, hoists, printing presses, washing machines, and movie cameras. Many of the principles and methods of design that apply to machines also apply to manufactured articles that are not true machines. The term "mechanical design" is used in a broader sense than "machine design" to include their design. the motion and structural aspects and the provisions for retention and enclosure are considerations in mechanical design. Applications occur in the field of mechanical engineering, and in other engineering fields as well, all of which require mechanical devices, such as switches, cams, valves, vessels, and mixers.Keywords: Mechanical Design ；Rules for Design ；Design ProcessThe Design ProcessDesigning starts with a need apparatus may need improvements in durability, efficiency, weight, speed, or cost. New apparatus may be needed to perform a function previously done by men, such as computation, assembly, or servicing. With the objective wholly or partly.In the design preliminary stage, should allow to design the personnel fully to display the creativity, not each kind of restraint. Even if has had many impractical ideas, also can in the design early time, namely in front of the plan blueprint is corrected. Only then, only then does not send to stops up the innovation the mentality. Usually, must propose several sets of design proposals, then perform the comparison. Has the possibility very much in the plan which finally designated, has used certain not in plan some ideas which accepts.When the general shape and a few dimensions of the several components become apparent, analysis can begin in earnest. The analysis will have as its objective satisfactory or superior performance, plus safety and durability with minimum weight, and a competitive cost. Optimum proportions and dimensions will be sought for each critically loaded section, together with a balance between the strengths of the several components. Materials and their treatment will be chosen. These important objectives can be attained only by analysis based upon the principles of mechanics, such as those of static for reaction forces and for the optimum utilization of friction; of dynamics for inertia, acceleration, and energy; of elasticity and strength of materials for stress and deflection; of physical behavior of materials; and of fluid mechanics for lubrication and hydrodynamic drives. The analyses may be made by the same engineer who conceived the arrangement of mechanisms, or, in a large company, they may be made by a separate analysis division or research group. Design is a reiterative and cooperative process, whether done formally or informally, and the analyst can contribute to phases other than his own. Product design requires much research and development. Many Concepts of an idea must be studied, tried, and then either used or discarded. Although the content of each engineering problem is unique, the designers follow the similar process to solve the problems.Product liability suits designers and forced in material selection, using the best program. In the process of material, the most common problems for five (a) don't understand or not use about the latest application materials to the best information, (b) failed to foresee and consider the reasonable use material may (such as possible, designers should further forecast and consider due to improper use products. In recent years, many products liability in litigation, the use of products and hurt the plaintiff accused manufacturer, and won the decision), (c) of the materials used all or some of the data, data, especially when the uncertainty long-term performance data is so, (d) quality control method is not suitable and unproven, (e) by some completely incompetent persons choose materials.Through to the above five questions analysis, may obtain these questions is does not have the sufficient reason existence the conclusion. May for avoid these questions to these questions research analyses the appearance indicating the direction. Although uses the best choice of material method not to be able to avoid having the product responsibility lawsuit, designs the personnel and the industry carries on the choice of material according to the suitable procedure, may greatly reduce the lawsuit the quantity.May see from the above discussion, the choice material people should to the material nature, the characteristic and the processing method have comprehensive and the basic understanding.Finally, a design based upon function, and a prototype may be built. If its tests are satisfactory, the initial design will undergo certain modifications that enable it to be manufactured in quantity at a lower cost. During subsequent years of manufacture and service, the design is likely to undergo changes as new ideas are conceived or as further analyses based upon tests and experience indicate alterations. Sales appeal.Some Rules for DesignIn this section it is suggested that, applied with a creative attitude, analyses can lead to important improvements and to the conception and perfection of alternate, perhaps more functional, economical,and durable products.To stimulate creative thought, the following rules are suggested for the designer and analyst. The first six rules are particularly applicable for the analyst.1. A creative use of need of physical properties and control process.2. Recognize functional loads and their significance.3. Anticipate unintentional loads.4. Devise more favorable loading conditions.5. Provide for favorable stress distribution and stiffness with minimum weight.6. Use basic equations to proportion and optimize dimensions.7. Choose materials for a combination of properties.8. Select carefully, stock and integral components.9. Modify a functional design to fit the manufacturing process and reduce cost.10. Provide for accurate location and noninterference of parts in assembly.Machinery design covers the following contents.1. Provides an introduction to the design process , problem formulation ,safety factors.2. Reviews the material properties and static and dynamic loading analysis ,Including beam , vibration and impact loading.3. Reviews the fundamentals of stress and defection analysis.4. Introduces fatigue-failure theory with the emphasis on stress-life approaches to high-cycle fatigue design, which is commonly used in the design of rotation machinery.thoroughly the phenomena of wear mechanisms, surface contact stresses ,and surface fatigue.shaft design using the fatigue-analysis techniques.fluid-film and rolling-element bearing theory and applicationa thorough introduction to the kinematics, design and stress analysis of spur gears , and a simple introduction to helical ,bevel ,and worm gearing.spring design including compression ,extension and torsion springs.with screws and fasteners including power screw and preload fasteners.the design and specification of disk and drum clutches and brakes.Machine DesignThe complete design of a machine is a complex process. The machine design is a creative work. Project engineer not only must have the creativity in the work, but also must in aspect and so on mechanical drawing, kinematics, engineerig material, materials mechanics and machine manufacture technology has the deep elementary knowledge.One of the first steps in the design of any product is to select the material from which each part is to be made. Numerous materials are available to today's designers. The function of the product, its appearance, the cost of the material, and the cost of fabrication are important in making a selection. A careful evaluation of the properties of a. material must be made prior to any calculations.Careful calculations are necessary to ensure the validity of a design. In case of any part failures, it is desirable to know what was done in originally designing the defective components. The checking of calculations (and drawing dimensions) is of utmost importance. The misplacement of one decimal point can ruin an otherwise acceptable project. All aspects of design work should be checked and rechecked.The computer is a tool helpful to mechanical designers to lighten tedious calculations, and provide extended analysis of available data. Interactive systems, based on computer capabilities, have made possible the concepts of computer aided design (CAD) and computer-aided manufacturing (CAM). How does the psychologist frequently discuss causes the machine which the people adapts them to operate. Designs personnel''s basic responsibility is diligently causes the machine to adapt the people. This certainly is not an easy work, because certainly does not have to all people to say in fact all is the most superior operating area and the operating process. Another important question, project engineer must be able to carry on the exchange and the consultation with other concerned personnel. In the initial stage, designs the personnel to have to carry on the exchange and the consultation on the preliminary design with the administrative personnel, and is approved. This generally is through the oral discussion, the schematic diagram and the writing material carries on.If front sues, the machine design goal is the production can meet the human need the product. The invention, the discovery and technical knowledge itself certainly not necessarily can bring the advantage to the humanity, only has when they are applied can produce on the product the benefit. Thus, should realize to carries on before the design in a specific product, must first determine whether the people do need this kind of productMust regard as the machine design is the machine design personnel carries on using creative ability the product design, the system analysis and a formulation productmanufacture technology good opportunity. Grasps the project elementary knowledge to have to memorize some data and the formula is more important than. The merely service data and the formula is insufficient to the completely decision which makes in a good design needs. On the other hand, should be earnest precisely carries on all operations. For example, even if places wrong a decimal point position, also can cause the correct design to turn wrongly.A good design personnel should dare to propose the new idea, moreover is willing to undertake the certain risk, when the new method is not suitable, use original method. Therefore, designs the personnel to have to have to have the patience, because spends the time and the endeavor certainly cannot guarantee brings successfully. A brand-new design, the request screen abandons obsoletely many, knows very well the method for the people. Because many person of conservativeness, does this certainly is not an easy matter. A mechanical designer should unceasingly explore the improvement existing product the method, should earnestly choose originally, the process confirmation principle of design in this process, with has not unified it after the confirmation new idea.机械设计李庆余, 张佳.机械制造装备设计摘要机器是由机械装置和其它组件组成的。
机械专业毕业论文外文翻译
附录一英文科技文献翻译英文原文：Experimental investigation of laser surface textured parallel thrust bearingsPerformance enhancements by laser surface texturing (LST) of parallel-thrust bearings is experimentally investigated. Testresults are compared with a theoretical model and good correlation is found over the relevant operating conditions. A compari-son of the performance of unidirectional and bi-directional partial-LST bearings with that of a baseline, untextured bearing ispresented showing the benefits of LST in terms of increased clearance and reduced friction.KEY WORDS: fluid film bearings, slider bearings, surface texturing1. IntroductionThe classical theory of hydrodynamic lubrication yields linear (Couette) velocity distribution with zero pressure gradients between smooth parallel surfaces under steady-state sliding. This results in an unstable hydrodynamic film that would collapse under any external force acting normal to the surfaces. However, experience shows that stable lubricating films can develop between parallel sliding surfaces, generally because of some mechanism that relaxes one or more of the assumptions of the classical theory.A stable fluid film with sufficient load-carrying capacity in parallel sliding surfaces can be obtained, for example, with macro or micro surface structure of different types. These include waviness [1] and protruding microasperities [2–4]. A good literature review on the subject can be found in Ref. [5]. More recently, laser surface texturing (LST) [6–8], as well as inlet roughening by longitudinal or transverse grooves [9] were suggested to provide load capacity in parallel sliding. The inlet roughness concept of Tonder [9] is based on ‘‘effective clearanc e’’ reduction in the sliding direction and in this respect it is identical to the par- tial-LST concept described in ref.[10] for generating hydrostatic effect in high-pressure mechanical seals.Very recently Wang et al. [11] demonstrated experimentally a doubling of the load-carrying capacity for the surface- texture design by reactive ion etching of SiCparallel-thrust bearings sliding in water. These simple parallel thrust bearings are usually found in seal-less pumps where the pumped fluid is used as the lubricant for the bearings. Due to the parallel sliding their performance is poorer than more sophisticated tapered or stepped bearings. Brizmer et al. [12] demon-strated the potential of laser surface texturing in the form of regular micro-dimples for providing load-carrying capacity with parallel-thrust bearings. A model of a textured parallelslider was developed and the effect of surface texturing on load-carrying capacitywas analyzed. The optimum parameters of the dimples were found in order to obtainmaximum load-carrying capacity. A micro-dimple ‘‘collective effect’’ was identi-fied that is capable of generating substantial load-carrying capacity, approaching that of optimumconventional thrust bearings. The purpose of the present paper is to investigate experimentally the validity of the model described in Ref. [12] by testing practical thrust bearings and comparing the performance of LST bearings with that of the theoretical predictions and with the performance of standard non-textured bearings2. BackgroundA cross section of the basic model that was analyzed in Ref. [12] is shown in figure1. A slider having a width B is partially textured over a portion Bp =αB of its width.The textured surface consists of multiple dimples with a diameter，depth and area density Sp. As a result of the hydrodynamic pressure generated by the dimples the sliding surfaces will be separated by a clearance depending on the sliding velocity U, the fluid viscosity l and the external load It was found in Ref. [12] that an optimum ratio exists for the parameter that provides maximum dimensionless load-carrying capacity where L isthe bearing length, and this optimum value is hp=1.25. It was further found in Ref. [12] that an optimum value exists for the textured portion a depending onthe bearing aspect ratio L/B. This behavior is shown in figure 2 for a bearing with L/B = 0.75 at various values of the area density Sp. As can be seen in the range of Sp values from 0.18 to 0.72 the optimum a value varies from 0.7 to 0.55, respectively. It can also be seen from figure 2 that for a < 0.85 no optimum value exists for Sp and the maximum load W increases with increasing Sp. Hence, the largest area density that can be practically obtained with the laser texturing is desired. It is also interesting to note from figure 2 the advantage of partial-LST (a < 1) over the full LST (a = 1) for bearing applications. At Sp= 0.5, for example, the load W at a = 0.6 is about three times higher than its value at a = 1. A full account of this behavior is given in Ref. [12].3. ExperimentalThe tested bearings consist of sintered SiC disks 10 mm thick, having 85 mm outer diameter and 40 mm inner diameter. Each bearing (see figure 3) comprises a flat rotor (a) and a six-pad stator (b). The bearings were pr ovided with an original surface finish by lapping to a roughness average Ra= 0.03 lm. Each pad has an aspect ratio of 0.75 when its width is measured along the mean diameter of the stator. The photographs of two partial-LST stators are shown in figure 4 wher e the textured areas appear as brighter matt surfaces. The first stator indicated (a) is a unidirectional bearing with the partial-LST adjacent to the leading edge of each pad, similar to the model shown in figure 1. The second stator (b) is a bi-directional version of a partial-LST bearing having two equal textured portions, a/2, on each of the pad ends. The laser texturing parameters were the following; dimple depth, dimplediameter and dimple area density Sp= 0.60.03. These dimple dimensions were obtained with 4 pulses of 30 ns duration and 4 mJ each using a 5 kHz pulsating Nd:YAG laser. The textured portion of the unidirectional bearing was a= 0.73 and that of the bi-directional bearing was a= 0.63. As can be seen from figure 2 both these a values should produce load-carrying capacity vary close to the maximum theoretical value.The test rig is shown schematically in figure 5. An electrical motor turns a spindle to which an upper holder of the rotor is attached. A second lower holder of the stator is fixed to a housing, which rests on a journal bearing and an axial loading mechanism that can freely move in the axial direction. An arm that presses against a load cell and thereby permits friction torque measurements prevents the free rotation of this housing. Axial loading is provided by means of dead weights on a lever and is measured with a second load cell. A proximity probe that is attached to the lower holder of the stator allows on-line measurements of the clearance change between rotor and stator as the hydrodynamiceffects cause axial movement of the housing to which the stator holder is fixed. Tapwater is supplied by gravity from a large tank to the center of the bearing and the leakage from the bearing is collected and re-circulated. A thermocouple adjacent to the outer diameter of the bearing allows monitoring of the water temperature as the water exit the bearing. A PC is used to collect and process data on-line. Hence,theinstantaneous clearance, friction coefficient, bearing speed and exit water temperaturecan be monitored constantly.The test protocol includes identifying a reference “zero” point for the clearance measurements by first loading and then unloading a stationary bearing over the full load range. Then the lowest axial load is applied, the water supply valve is opened and the motor turned on. Axial loading is increased by steps of 40 N and each load step is maintained for 5 min following the stabilization of the friction coefficient ata steady-state value. The bearing speed and water temperature are monitored throughout the test for any irregularities. The test ends when a maximum axial load of 460 N is reached or if the friction coefficient exceeds a value of 0.35. At the end ofthe last load step the motor and water supply are turned off and the reference for the clearance measurements is rechecked. Tests are performed at two speeds of 1500and 3000 rpm corresponding to average sliding velocities of 4.9 and 9.8 m/s, respectively and each test is repeated at least three times.4. Results and discussionAs a first step the validity of the theoretical model in Ref. [12] was examined by comparing the theoretical and experimental results of bearing clearance versus bearing load for a unidirectional partial-LST bearing. The results are shown in fig ure 6 for the two speeds of 1500 and 3000 rpm where the solid and dashed lines correspond to the model and experiment, respectively. As can be seen, the agreement between the model and the experiment is good, with differences of less than 10%, aslong as the load is above 150 N. At lower loads the measured experimental clearances are much larger than the model predictions, particularly at the higher speed of 3000 rpm where at 120 N the measured clearance is 20 lm, which is about 60% higher than the predicted value. It turns out that the combination of such large clearances and relatively low viscosity of the water may result in turbulent fluid film. Hence, the assumption of laminar flow on which the solution of the Reynolds equation in Ref.[12] is based may be violated making the model invalid especially at the higher speed and lowest load. In order to be consistent with the model of Ref. [12] it was decided to limit further comparisons to loads above 150 N.It should be noted here that the first attempts t o test the baseline untextured bearing with the original surface finish of Ra= 0.03 lm on both the stator and rotor failed due to extremely high friction even at the lower loads. On the other hand the partial-LST bearing ran smoothly throughout the load range. It was found that the post-LST lapping to completely remove about 2 lm height bulges, which are formed during texturing around the rims of the dimples, resulted in a slightly rougher surface with Ra= 0.04 lm. Hence, the baseline untextured stator was also lapped to the same rough- ness of the partial-LST stator and all subsequent tests were performed with the same Ra value of 0.04 lm for all the tested stators. The rotor surface roughness remained, the original one namely, 0.03 lm. Figure 7 presents the experimental resultsfor the clearance as a function of the load for a partial-LST unidirectional bearing (see stator in figure 4(a)) and a baseline untextured bearing. The comparison is made at the two speeds of 1500 and 3000 rpm. The area density of the dimples in the partial-LST bearing is Sp= 0.6 and the textured portion is a ¼ 0:734. The load range extends from 160 to 460 N. The upper load was determined by the test-rig limitation that did not permit higher loading. It is clear from figure 7 that the pa rtial-LST bearing operates at substantially larger clearances than the untextured bearing. At the maximum load of 460 N and speed of 1500 rpm the partial-LST bearing has a clearance of 6 lm while the untextured bearing clearance is only 1.7 lm. At 3000 rpm the clearances are 6.6 and 2.2 lm for the LST and untextured bearings, respectively. As can be seen from figure 7 this ratio of about 3 in favor of the partial-LST bearing is maintained over the entire load range.Figure 8 presents the results for the bi-directionalbearing (see stator in figure 4(b)). In this case the LST parameters are Sp ¼ 0:614 and a ¼ 0:633. The clearances of the bi-directional partial-LST bearing are lower compared to these of the unidirectional bearing at the same load. At 460 N load the clearance for the 1500 rpm is 4.1 lm and for the 3000 rpm it is 6 lm. These values represent a reduction of clearance between 33 and 10% compared to the unidirectional case. However, as can be seen from figure 8 the performance of the partial-LST bi-directional bearing is still substantially better than that of the untextured bearing.The friction coefficient of partial-LST unidirectional and bi-directional bearings was compared with that of the untextured bearing in figures 9 and 10 for the two speeds of 1500 and 3000 rpm, respectively. As can be seen the friction coefficient of the two partial-LST bearings is very similar with slightly lower values in the case of the more efficient unidirectional bearing. The friction coefficient of the untextured bearing is much larger compared to that of the LST bearings. At 1500 rpm (figure 9) and the highest load of 460 N the friction coefficient of the untextured bearing is about 0.025 compared to about 0.01 for the LST bearings.At the lowest load of 160 N the values are about 0.06 for the untextured bearing and around 0.02 for the LST bearings. Hence, the friction values of the untextured bearing are between 2.5 and 3 times higher than the corresponding values for the partial-LST bearings over the entire load range. Similar results were obtained at the velocity of3000 rpm (figure 10) but the level of the friction coefficients is somewhat higherdue to the higher speed. The much higher friction of the untextured bearing is due to the much smaller clearances of this bearing (see figures 7 and 8) that result in higher viscous shear.Bearings fail for a number of reasons，but the most common are misapplication，contamination，improper lubricant，shipping or handling damage，and misalignment. The problem is often not difficult to diagnose because a failed bearing usually leaves telltale signs about what went wrong．However，while a postmortem yields good information，it is better to avoid the process altogether by specifying the bearing correctly in The first place．To do this，it is useful to review the manufacturers sizing guidelines and operating characteristics for the selected bearing.Equally critical is a study of requirements for noise, torque, and runout, as well as possible exposure to contaminants, hostile liquids, and temperature extremes. This can provide further clues as to whether a bearing is right for a job.1 Why bearings failAbout 40% of ball bearing failures are caused by contamination from dust, dirt, shavings, and corrosion. Contamination also causes torque and noise problems, and isoften the result of improper handling or the application environment．Fortunately, a bearing failure caused by environment or handling contamination is preventable，and a simple visual examination can easily identify the cause．Conducting a postmortem il1ustrates what to look for on a failed or failing bearing．Then，understanding the mechanism behind the failure, such as brinelling or fatigue, helps eliminate the source of the problem.Brinelling is one type of bearing failure easily avoided by proper handing and assembly. It is characterized by indentations in the bearing raceway caused by shock loading－such as when a bearing is dropped-or incorrect assembly. Brinelling usually occurs when loads exceed the material yield point(350,000 psi in SAE 52100 chrome steel)．It may also be caused by improper assembly, Which places a load across the races．Raceway dents also produce noise，vibration，and increased torque.A similar defect is a pattern of elliptical dents caused by balls vibrating between raceways while the bearing is not turning．This problem is called false brinelling. It occurs on equipment in transit or that vibrates when not in operation. In addition, debris created by false brinelling acts like an abrasive, further contaminating the bearing. Unlike brinelling, false binelling is often indicated by a reddish color from fretting corrosion in the lubricant.False brinelling is prevented by eliminating vibration sources and keeping the bearing well lubricated. Isolation pads on the equipment or a separate foundation may be required to reduce environmental vibration. Also a light preload on the bearing helps keep the balls and raceway in tight contact. Preloading also helps prevent false brinelling during transit.Seizures can be caused by a lack of internal clearance, improper lubrication, or excessive loading. Before seizing, excessive, friction and heat softens the bearing steel. Overheated bearings often change color，usually to blue-black or straw colored．Friction also causes stress in the retainer，which can break and hasten bearing failure．Premature material fatigue is caused by a high load or excessive preload．When these conditions are unavoidable，bearing life should be carefully calculated so that a maintenance scheme can be worked out．Another solution for fighting premature fatigue is changing material．When standard bearing materials，such as 440C or SAE 52100，do not guarantee sufficient life，specialty materials can be recommended. In addition，when the problem is tracedback to excessive loading，a higher capacity bearing or different configuration may be used．Creep is less common than premature fatigue．In bearings．it is caused by excessive clearance between bore and shaft that allows the bore to rotate on the shaft．Creep can be expensive because it causes damage to other components in addition to the bearing．0ther more likely creep indicators are scratches，scuff marks，or discoloration to shaft and bore．To prevent creep damage，the bearing housing and shaft fittings should be visually checked．Misalignment is related to creep in that it is mounting related．If races are misaligned or cocked．The balls track in a noncircumferencial path．The problem is incorrect mounting or tolerancing，or insufficient squareness of the bearing mounting site．Misalignment of more than 1/4·can cause an early failure．Contaminated lubricant is often more difficult to detect than misalignment or creep．Contamination shows as premature wear．Solid contaminants become an abrasive in the lubricant．In addition。
毕业论文外文翻译-齿轮的加工方法
英文原文Gear manufacturing methodsThere are two basic methods of manufacturing gear teeth: the generating process and the forming process. when a gear tooth is generated, the workpiece and the cutting or grinding tool are in continuous mesh and the tooth form is generated by the tool. In other words, the work and the tool are conjugated to each other. hobbing :machines, shaper cutters, shaving machines, and grinders use this principle.When a gear tooth is formed, the tool is in the shape of the space that is being machined out. Some grinding machines use this principle with an indexing mechianism which allows the gear teeth to be formed tooth by tooth. Broaches are examples of form tools that machine all the gear teeth simultaneously.shapingShaping is inherently similar to planning but uses a circular cuttrer instead of rack and the resulting reduction in the reciprocating inertia allows much higher stroking speeds: modern shapers cutting car gears can run at 2,000 cutting strokes per minmute. The shape of the cutter is roughly the same as an involute gear but the tips of the teeth are rounded.The generating drive between cutter and workpiece does not involve a rack or leadscrew since only circular motion in involved. The tool and workpiece move tangential typically 0.5 mm for each stroke of the cutter. On the return stroke the cutter must be retracted about 1 mm to give clearance otherwise tool rub occurs on the backstroke and failure is rapid. The speed on this type of machine is limited by the rate at which some 50kg of cutter and bearings can be moved a distance of 1 mm. the accelerations involved tequire forces of the order of 5000N yet high accuracy must be maintained.The advantages of shaping are that production rates are relatively high and that it is possible to cut right up to a shoulder. Unfortunately, for helical gears, a helical guide is required to impose a rotational motion on the stroking motion; such helical guides cannot be produced easily or cheaply so the method is only suitable for long runs with helical gears since special cutters and guides must be manufactured for each different helix angle. A great advantage of shaping is its ability to annular gears such as those required for large epicyclie drives.When very high accuracy is of importance the inaccuracies in the shaping cutter matter since they may transfer to the cut gear. It is obvious that profile errors will transfer but it is less obvious than an eccentrically mounted or ground cutter will give a characteristic “dropped tooth”. There are several causes for “dropped tooth” but it occurs most commonly when the diameter of the workpiece is about half, one and half, two and a half, etc, times the cutter diameter. If the cutter starts on a high point and finishes on a low point during the final finishing revolution of the gear the peak to peak eccentricity errors in the cutter occurs between the last and the first tooth of the final revolution of the cut gear; as the cumulative pitch error of the cutter may well be over 25 microns there is a sudden pitch error of this amount on the cut gear. The next gear cut on the machine may however be very good on adjacent pitch if the final cut happened to start in a favorable position on the cutter.Various attempts have been made to prevent this effect, in particular by continuing rotation without any further cutter infeed but if the shaping machine is not very rigid and the cutter very sharp then no further cutting will occur and the error will not be removed.hobbinghobbing, the most used metal cutting method, uses the rack generating principle but avoids slow reciprocation by mounting many “racks ” on a rotating cutter. The “racks” are displaced axially to form a gashed worm. The “racks” do not generate the correct involute shape for the whole length of the teeth since they are moving on a circular path and so the hob is fed slowly along the teeth either axially in normal or in the direction of the helix in “oblique” hobbing.Metal removal rates are high since no reciprocation of hob or workpiece is required and so cutting speeds of 40 m/min can be used for conventional hobs and up to 150m/min for carbide hobs. Typically with a 100mm diameter hob the rotation speed will be 100rpm and so a twenty tooth workpiece will rotate at 5 rpm. Each revolution of the workpiece will correspond to 0.75mm feed so the hob will advance through the workpiece at about 4mm per minute. For car production roughing multiple start hobs can be used with coarse feeds of 3mm per revolution so that 100 rpm on the cutter, a two-start hob and a 20 tooth gear will give a feed rate of 30mm/minute.The disadvantage of a coarse feed rate is that a clear marking is left on the workpiece, particularly in the root, showing a pattern at a spacing of the feed rate per revolution. This surface undulation is less marked on the flanks than in the root and is not important when there is a subsequent finishing operation such as shaving or grinding. When there are no further operations the feed per revolution must be restricted to keep the undulations below a limit which is usually dictated by lubrication conditions. The height of the undulations in the root of the gear is given by squaring the feed per revolution and dividing by four times the diameter of the hob; 1 mm feed and 100mm diameter gives 2.5 micron high undulations in the root. On the gear flank the undulation is roughly cos70 as large, i.e., about 0.85 micron.Accuracy of hobbing is normally high for pitch and for helix, provided machines are maintained; involute is dependent solely on the accuracy of the hob profile. As the involute form is generated by as many cuts as there are gashes on the hob the involute is not exact, but if there are, say, 14 tangents generating a flank of 20 mm radius curvature about 4 mm high the divergence from a true involute is only about half a micron; hob manufacturing and mounting errors can be above 10 microns. Use of twostart hobs or oblique hobbing gives increased error levels since hob errors of pitching transfer to the cut gear.broachingBroaching is not used for helical gears but is useful for internal spur gears; the principal use of broaching in this context is for internal splines which cannot easily be made by any other method. As with all broaching the method is only economic for large quantities since setup costs are high.The major application of broaching techniques to helical external gears is that used by Gleasons in their G-TRAC machine .this machine operates by increasing the effective radius of a hobbing cutter to infinity so that each tooth of the cutter is travelingin a straight line instead of on a radius. This allows the cutting action to extend over the whole facewidth of a gear instead of the typical 0.75 mm feed per revolution of hobbing. The resulting process gives a very high production rate , more suitable for U.S.A. production volumes than for the relatively low European volumes and so, despite a high initial cost ,is very competitive.Broaching give high accuracy and good surface finish but like all cutting processes is limited to “soft” materials which must be subsequently casehardened or heat treated, giving distortion.ShavingA shaving cutting cutter looks like a gear which has extra clearance at the root and whose tooth flanks have been grooved to give cutting edges. It is run in mesh with the rough gear with crossed axes so that there is in theory point contact with a relative velocity along the teeth giving scraping action. The shaving cutter teeth are relatively flexible in bending and so will only operate effectively when they are in double contact between two gear teeth. The gear and cutter operate at high rotational speeds with traversing of the workface and about 100 mm micron of material is removed. Cycle times can be less than half a minute and the machines are not expensive but cutters are delicate and difficult to manufacture. It is easy to make adjustments of profile at the shaving stage and crowning can be applied. Shaving can be carried out near a shoulder by using a cutter which is plunged in to depth without axial movement; this method is fast but requires more complex cutter design.grindingGrinding is extremely important because it is the main way hardened gear are machined. When high accuracy is required it is not sufficient to pre-correct for heat treatment distortion and grinding is then necessary.The simplest approach to grinding, often termed the Orcutt method. The wheel profile is dressed accurately to shape using single point diamonds which are controlled by templates cut to the exact shape required; 6:1 scaling with a pantograph is often used. The profile wheel is then reciprocated axially along the gear which rotates to allow for helix angle effects; when one tooth shape has been finished, involving typically 100 micron metal removal the gear is indexed to the next tooth space. This method is fairly show but gives high accuracy consistently. Setting up is lengthy because different dressing templates are needed if module, number of teeth, helix angle, or profile correction are changed.The fastest grinding method uses the same principle as hobbing but replaces a gashed and relieved worm by a grinding wheel which is a rack in section. Since high surface speeds are needed the wheel diameter is increased so that wheels of 0.5 m diameter can run at over 2000 rpm to give the necessary 1000 m/min. only single start worms are cut on the wheel but gear rotation speeds are high,100 rpm typically, so it is difficult to design the drive system to give accuracy and rigidity. Accuracy of the process is reasonably high although there is a tendency for wheel and workpiece to deflect variably during grinding so the wheel form may require compensation for machine deflection effects. Generation of a worm shape on the grinding wheel is a slow process since a dressing diamond or roller must not only form the rack profile but has to move axially as the wheel rotates. Once the wheel has been trued, gears can be groundrapidly until redressing is required. This is the most popular method for high production rates with small gear and is usually called the Reishauer method.Large gears are usually generated by the Maag method which is similar to planning in its approach but uses cup grinding wheels of large diameter to form the flanks of the theoretical mating rack. Gears of very large diameter cannot easily be moved so the gear is essentially stationary while the grinding wheel carriage reciprocates in the direction of the helix. The wheel is only in contact over a small part of the facewidth in helical gears so this is not important when only a few gears of this size are made in a year. As with form grinding, after grinding a pair of flanks the gear is indexed to the next pair.A similar method used for medium size gears has stationary wheels, while the rough gear is traversed under the wheels. Corresponding rotational movement of the gear is controlled by steel bands unwrapping from a cylinder of pitch circle diameter so that the motion of gear relative to “rack” is correct.Another method, the Nile approach, uses a wheel which is formed to give the “theoretical mating rack” instead of using two cup wheels as in the Maag method. This approach is best suited to medium precision work on smaller gears and is intermediate in speed between the Reishauer and Maag methods.All grinding processes are slow and costly compared with cutting processed and so are only used when accuracy is essential. A rough rule of thumb is that grinding will increase gear cutting costs by a factor of 10 but the cost of the teeth is often only a small part of the total cost of a gearbox. The accuracies attainable are surprisingly not very dependent on size of gear ; whether a gear is 5 m or 50 m diameter the pitch involute and helix accuracies attainable are of the order of 5 microns or better and more dependent on the skill and patience of the operator and inspectors than on any other factors.It is often assumed that grinding will remove all error generated at the roughing stage. Unfortunately, grinding machines are relatively flexible and so the grinding wheel has a tendency to follow previous errors. The errors will thus be reduced but not completely eliminated unless very many cuts are used; whenever a grinding process is giving in consistent results it is advisable to check the accuracies at the rough-cut stage. The only exception is the form grinding process which will not follow involute errors though it will still allow helix and pitch errors.中文译文齿轮的加工方法加工齿轮轮齿有两种基本的方法：产生过程和形成过程。
【精品毕设】机电专业论文英文文献及其中文译文
毕业论文外文文献翻译译文题目:INTEGRATION OF MACHINERY外文资料翻译资料来源：文章名：INTEGRATION OF MACHINERY 《Digital Image Processing》书刊名：作者：Y. Torres J. J. Pavón I. Nieto and J. A.Rodríguez章节：2.4 INTEGRATION OF MACHINERYINTEGRATION OF MACHINERY （From ELECTRICAL AND MACHINERY INDUSTRY）ABSTRACT Machinery was the modern science and technology development inevitable resultthis article has summarized the integration of machinery technology basic outlineand the development background .Summarized the domestic and foreign integration ofmachinery technology present situation has analyzed the integration of machinerytechnology trend of development. Key word：integration of machinery ，technology，present situation ，productt，echnique of manufacture ，trend of development 0. Introduction modern science and technology unceasing development impelleddifferent discipline intersecting enormously with the seepage has caused the projectdomain technological revolution and the transformation .In mechanical engineeringdomain because the microelectronic technology and the computer technology rapiddevelopment and forms to the mechanical industry seepage the integration of machinerycaused the mechanical industry the technical structure the product organizationthe function and the constitution the production method and the management systemhas had the huge change caused the industrial production to enter into quottheintegration of machineryquot by quotthe machinery electrificationquot for the characteristicdevelopment phase. 1. Integration of machinery outline integration of machinery is refers in theorganization new owner function the power function in the information processingfunction and the control function introduces the electronic technology unifies thesystem the mechanism and the computerization design and the software whichconstitutes always to call. The integration of machinery development also has becomeone to have until now own system new discipline not only develops along with thescience and technology but also entrusts with the new content .But its basiccharacteristic may summarize is: The integration of machinery is embarks from thesystem viewpoint synthesis community technologies and so on utilization mechanicaltechnology microelectronic technology automatic control technology computertechnology information technology sensing observation and control technologyelectric power electronic technology connection technology information conversiontechnology as well as software programming technology according to the systemfunction goal and the optimized organization goal reasonable disposition and thelayout various functions unit in multi-purpose high grade redundant reliable inthe low energy consumption significance realize the specific function value andcauses the overall system optimization the systems engineering technology .From thisproduces functional system then becomes an integration of machinery systematic orthe integration of machinery product. Therefore quotintegration of machineryquot coveringquottechnologyquot and quotproductquot two aspects .Only is the integration of machinerytechnology is based on the above community technology organic fusion one kind ofcomprehensivetechnology but is not mechanical technical the microelectronictechnology as well as other new technical simple combination pieces together .Thisis the integration of machinery and the machinery adds the machinery electrificationwhich the electricity forms in the concept basic difference .The mechanicalengineering technology has the merely technical to develop the machineryelectrification still was the traditional machinery its main function still wasreplaces with the enlargement physical strength .But after develops the integrationof machinery micro electron installment besides may substitute for certainmechanical parts the original function but also can entrust with many new functionslike the automatic detection the automatic reduction information demonstrate therecord the automatic control and the control automatic diagnosis and the protectionautomatically and so on .Not only namely the integration of machinery product ishumans hand and body extending humans sense organ and the brains look has theintellectualized characteristic is the integration of machinery and the machineryelectrification distinguishes in the function essence. 2. Integration of machinery development condition integration of machinerydevelopment may divide into 3 stages roughly.20th century 60s before for the firststage this stage is called the initial stage .In this time the people determinationnot on own initiative uses the electronic technology the preliminary achievement toconsummate the mechanical product the performance .Specially in Second World Warperiod the war has stimulated the mechanical product and the electronic technologyunion these mechanical and electrical union military technology postwar transferscivilly to postwar economical restoration positive function .Developed and thedevelopment at that time generally speaking also is at the spontaneouscondition .Because at that time the electronic technology development not yetachieved certain level mechanical technical and electronic technology union alsonot impossible widespread and thorough development already developed the productwas also unable to promote massively. The 20th century 7080 ages for the second stagemay be called the vigorous development stage .This time the computer technologythe control technology the communication development has laid the technology basefor the integration of machinery development . Large-scale ultra large scaleintegrated circuit and microcomputer swift and violent development has provided thefull material base for the integration of machinery development .This timecharacteristic is :①A mechatronics word first generally is accepted in Japanprobably obtains the quite widespread acknowledgment to 1980s last stages in theworldwide scale ②The integration of machinery technology and the product obtainedthe enormous development ③The various countries start to the integration ofmachinery technology and the product give the very big attention and the support.1990s later periods started the integration of machinery technology the new stagewhich makes great strides forward to the intellectualized direction the integrationof machinery enters the thorough development time .At the same time optics thecommunication and so on entered the integration of machinery processes thetechnology also zhan to appear tiny in the integration of machinery the footappeared the light integration of machinery and the micro integration of machineryand so on the new branch On the other hand to the integration ofmachinery systemmodeling design the analysis and the integrated method the integration ofmachinery discipline system and the trend of development has all conducted thethorough research .At the same time because the hugeprogress which domains and so on artificial intelligence technology neural networktechnology and optical fiber technology obtain opened the development vast worldfor the integration of machinery technology .These research will urge theintegration of machinery further to establish the integrity the foundation and formsthe integrity gradually the scientific system. Our country is only then starts fromthe beginning of 1980s in this aspect to study with the application .The State Councilhad been established the integration of machinery leading group and lists as quot863plansquot this technology .When formulated quot95quot the plan and in 2010 developed thesummary had considered fully on international the influence which and possiblybrought from this about the integration of machinery technology developmenttrend .Many universities colleges and institutes the development facility and somelarge and middle scale enterprises have done the massive work to this technicaldevelopment and the application does not yield certain result but and so on theadvanced countries compared with Japan still has the suitable disparity. 3. Integration of machinery trend of development integrations of machinery arethe collection machinery the electron optics the control the computer theinformation and so on the multi-disciplinary overlapping syntheses its developmentand the progress rely on and promote the correlation technology development and theprogress .Therefore the integration of machinery main development direction is asfollows: 3.1 Intellectualized intellectualizations are 21st century integration ofmachinery technological development important development directions .Theartificial intelligence obtains day by day in the integration of machineryconstructors research takes the robot and the numerical control engine bedintellectualization is the important application .Here said quottheintellectualizationquot is to the machine behavior description is in the control theoryfoundation the absorption artificial intelligence the operations research thecomputer science the fuzzy mathematics the psychology the physiology and the chaosdynamics and so on the new thought the new method simulate the human intelligenceenable it to have abilities and so on judgment inference logical thinkingindependent decision-making obtains the higher control goal in order to .Indeedenable the integration of machinery product to have with the human identicalintelligence is not impossible also is nonessential .But the high performancethe high speed microprocessor enable the integration of machinery product to havepreliminary intelligent or humans partial intelligences then is completelypossible and essential. In the modern manufacture process the information has become the controlmanufacture industry the determining factor moreover is the most active actuationfactor .Enhances the manufacture system information-handling capacity to become themodern manufacture science development a key point .As a result of the manufacturesystem information organization and structure multi-level makes the information thegain the integration and the fusion presents draws up the character informationmeasuremulti-dimensional as well as information organizations multi-level .In themanufacture information structural model manufacture information uniform restraintdissemination processing and magnanimous data aspects and so on manufacture knowledgelibrary management all also wait for further break through. Each kind of artificial intelligence tool and the computation intelligence methodpromoted the manufacture intelligence development in the manufacture widespreadapplication .A kind based on the biological evolution algorithm computationintelligent agent in includes thescheduling problem in the combination optimization solution area of technologyreceives the more and more universal attention hopefully completes the combinationoptimization question when the manufacture the solution speed and the solutionprecision aspect breaks through the question scale in pairs the restriction .Themanufacture intelligence also displays in: The intelligent dispatch the intelligentdesign the intelligent processing the robot study the intelligent control theintelligent craft plan the intelligent diagnosis and so on are various These question key breakthrough may form the product innovation the basicresearch system. Between 2 modern mechanical engineering front science differentscience overlapping fusion will have the new science accumulation the economicaldevelopment and societys progress has had the new request and the expectation tothe science and technology thus will form the front science .The front science alsohas solved and between the solution scientific question border area .The front sciencehas the obvious time domain the domain and the dynamic characteristic .The projectfront science distinguished in the general basic science important characteristicis it has covered the key science and technology question which the project actualappeared. Manufacture system is a complex large-scale system for satisfies the manufacturesystem agility the fast response and fast reorganization ability must profit fromthe information science the life sciences and the social sciences and so on themulti-disciplinary research results the exploration manufacture system newarchitecture the manufacture pattern and the manufacture system effectiveoperational mechanism .Makes the system optimization the organizational structureand the good movement condition is makes the system modeling the simulation andthe optimized essential target .Not only the manufacture system new architecture tomakes the enterprise the agility and may reorganize ability to the demand responseability to have the vital significance moreover to made the enterprise first floorproduction equipment the flexibility and may dynamic reorganization ability set ahigher request .The biological manufacture view more and more many is introduced themanufacture system satisfies the manufacture system new request. The study organizes and circulates method and technique of complicated systemfrom the biological phenomenon is a valid exit which will solve many hard nut tocracks that manufacturing industry face from now on currently .Imitating to livingwhat manufacturing point is mimicry living creature organ of from the organizationfrom match more from growth with from evolution etc. function structure and circulatemode of a kind of manufacturing system and manufacturing process. The manufacturing drives in the mechanism under continuously by ones ownperfect raise on organizing structure and circulating modeand thus to adapt theprocess ofwith ability for the environment .For from descend but the last productproceed together a design and make a craft rules the auto of the distance born producesystem of dynamic state reorganization and product and manufacturing the system tendautomatically excellent provided theories foundation and carry out acondition .Imitate to living a manufacturing to belong to manufacturing science andlife science ofquotthe far good luck is miscellaneous to hand overquot it will produceto the manufacturing industry for 21 centuries huge of influence .机电一体化摘要机电一体化是现代科学技术发展的必然结果本文简述了机电一体化技术的基本概要和发展背景。
机械专业英语论文翻译
RisersRisers are designed and placed so as to ensure filling the cavity during solidification.They also act to relieve gas pressure in the mold and to reduce pressure on the lifting surfaces of the mold.The volume of metal in the riser should be sufficient to retain heat long enough to feed the shrinkage cavity and to equalize the temperature in the mold, avoiding casting strains.The riser requirements vary with the type of metal being poured.Gray cast iron, for example, needs less feeding than some alloys because a period of graphitization occurs during the final stages of solidification, which causes an expansion that tends to counteract the metal shrinkage.Many nonferrous metals require elaborate feeding that tends to counteract the casting.Two riser designs for the same casting are shown in Fig.7-4.Risers are placed near the heavy sections of the casting. The feed metal must be located above the highest point of the point of the casting.Chill BlocksChill blocks are metal blocks placed in the mold for localized heat dissipation.They may be placed at an intersection or joint where there is a comparatively large volume of metal to cool, thus relieving a hot spot or maintaining a more uniform cooling rate and better microstructure.They may also be placed at far surface of a mold, away from a riser or sprue.This will help the far end of the mold to freeze rapidly, promoting directional solidification.Chill blocks are also used at points where it is designable to have localized hardening, as in the case of bearings or wear surfaces.PaddingPadding consists of adding to or building up a section to obtain adequate feeding of isolated sections.Fig.7-4showed two methods of feeding the central and outside boss .Shown at (b) is the plan of using two risers and at (c) one riser with a pad. The second plan provides a yield of 45% of the metal poured, compared to 30% when two risers are used. The feeding distance to the central hub is 4.5t, where t= the thickness of the feed path. By rule of thumb, the total thickness of pad and castinuld not be less than one-fifth of the metal-feeding distance. This rule is not absolute but a good generalization.
机械类英语论文及翻译翻译
High-speed millingHigh-speed machining is an advanced manufacturing technology, different from the traditional processing methods. The spindle speed, cutting feed rate, cutting a small amount of units within the time of removal of material has increased three to six times. With high efficiency, high precision and high quality surface as the basic characteristics of the automobile industry, aerospace, mold manufacturing and instrumentation industry, such as access to a wide range of applications, has made significant economic benefits, is the contemporary importance of advanced manufacturing technology. For a long time, people die on the processing has been using a grinding or milling EDM (EDM) processing, grinding, polishing methods. Although the high hardness of the EDM machine parts, but the lower the productivity of its application is limited. With the development of high-speed processing technology, used to replace high-speed cutting, grinding and polishing process to die processing has become possible. To shorten the processing cycle, processing and reliable quality assurance, lower processing costs.1 One of the advantages of high-speed machiningHigh-speed machining as a die-efficient manufacturing, high-quality, low power consumption in an advanced manufacturing technology. In conventional machining in a series of problems has plagued by high-speed machining of the application have been resolved.1.1 Increase productivityHigh-speed cutting of the spindle speed, feed rate compared withtraditional machining, in the nature of the leap, the metal removal rate increased 30 percent to 40 percent, cutting force reduced by 30 percent, the cutting tool life increased by 70% . Hardened parts can be processed, a fixture in many parts to be completed rough, semi-finishing and fine, and all other processes, the complex can reach parts of the surface quality requirements, thus increasing the processing productivity and competitiveness of products in the market.1.2 Improve processing accuracy and surface qualityHigh-speed machines generally have high rigidity and precision, and other characteristics, processing, cutting the depth of small, fast and feed, cutting force low, the workpiece to reduce heat distortion, and high precision machining, surface roughness small. Milling will be no high-speed processing and milling marks the surface so that the parts greatly enhance the quality of the surface. Processing Aluminum when up Ra0.40.6um, pieces of steel processing at up to Ra0.2 ~ 0.4um.1.3 Cutting reduce the heatBecause the main axis milling machine high-speed rotation, cutting a shallow cutting, and feed very quickly, and the blade length of the workpiece contacts and contact time is very short, a decrease of blades and parts of the heat conduction. High-speed cutting by dry milling or oil cooked up absolute (mist)lubrication system, to avoid the traditional processing tool in contact with the workpiece and a lot of shortcomings to ensure that the tool is not high temperature under the conditions of work, extended tool life.1.4 This is conducive to processing thin-walled partsHigh-speed cutting of small cutting force, a higher degree of stability, Machinable with high-quality employees compared to the company may be very good, but other than the company's employees may Suanbu Le outstanding work performance. For our China practice, we use the models to determine the method of staff training needs are simple and effective. This study models can be an external object, it can also be a combination of internal and external. We must first clear strategy for the development of enterprises. Through the internal and external business environment and organizational resources, such as analysis, the future development of a clear business goals and operational priorities. According to the business development strategy can be compared to find the business models, through a comparative analysis of the finalization of business models. In determining business models, a, is the understanding of its development strategy, or its market share and market growth rate, or the staff of the situation, and so on, according to the companies to determine the actual situation. As enterprises in different period of development, its focus is different, which means that enterprises need to invest the manpower and financial resources the focus is different. So in a certain period of time, enterprises should accurately selected their business models compared with the departments and posts, so more practical significance, because the business models are not always good, but to compare some aspects did not have much practical significance, Furthermore This can more fully concentrate on the business use of limited resources. Identify business models, and then take the enterprise of the corresponding departments and staff with the business models for comparison, the two can be found in the performance gap, a comparative analysis to find reasons, in accordance with this business reality, the final identification of training needs. The cost of training is needed, if not through an effective way to determine whether companies need to train and the training of the way, but blind to training, such training is difficult to achieve the desired results. A comparison only difference between this model is simple and practical training.1.5 Can be part of some alternative technology, such as EDM, grinding high intensity and high hardness processingHigh-speed cutting a major feature of high-speed cutting machine has the hardness of HRC60 parts. With the use of coated carbide cutter mold processing, directly to the installation of a hardened tool steel processing forming, effectively avoid the installation of several parts of the fixture error and improve the parts of the geometric location accuracy. In the mold of traditional processing, heat treatment hardening of the workpiece required EDM, high-speed machining replace the traditional method of cutting the processing, manufacturing process possible to omit die in EDM, simplifying the processing technology and investment costs .High-speed milling in the precincts of CNC machine tools, or for processing centre, also in the installation of high-speed spindle on the general machine tools. The latter not only has the processingcapacity of general machine tools, but also for high-speed milling, a decrease of investment in equipment, machine tools increased flexibility. Cutting high-speed processing can improve the efficiency, quality improvement, streamline processes, investment and machine tool investment and maintenance costs rise, but comprehensive, can significantly increase economic efficiency.2 High-speed millingHigh-speed milling the main technical high-speed cutting technology is cutting the development direction of one of it with CNC technology, microelectronic technology, new materials and new technology, such as technology development to a higher level. High-speed machine tools and high-speed tool to achieve high-speed cutting is the prerequisite and basic conditions, in high-speed machining in the performance of high-speed machine tool material of choice and there are strict requirements.2.1 High-speed milling machine in order to achieve high-speed machiningGeneral use of highly flexible high-speed CNC machine tools, machining centers, and some use a dedicated high-speed milling, drilling. At the same time a high-speed machine tool spindle system and high-speed feeding system, high stiffness of the main characteristics of high-precision targeting and high-precision interpolation functions, especially high-precision arc interpolation function. High-speed machining systems of the machine a higher demand, mainly in the following areas:General use of highly flexible high-speed CNC machine tools, machining centers, and some use a dedicated high-speed milling, drilling. At the same time a high-speed machine tool spindle system and high-speed feeding system, high stiffness of the main characteristics of high-precision targeting and high-precision interpolation functions, especially high-precision arc interpolation function. High-speed machining systems of the machine a higher demand, mainly in the following areas:High-speed milling machine must have a high-speed spindle, the spindle speed is generally 10000 ~ 100000 m / min, power greater than 15 kW. But also with rapid speed or in designated spots fast-stopping performance. The main axial space not more than 0 .0 0 0 2 m m. Often using high-speed spindle-hydrostatic bearings, air pressure-bearing, mixed ceramic bearings, magnetic bearing structure of the form. Spindle cooling general use within the water or air cooled.High-speed processing machine-driven system should be able to provide 40 ~ 60 m / min of the feed rate, with good acceleration characteristics, can provide 0.4 m/s2 to 10 m/s2 acceleration and deceleration. In order to obtain good processing quality, high-speed cutting machines must have a high enough stiffness. Machine bed material used gray iron, can also add a high-damping base of concrete, to prevent cutting tool chatter affect the quality of processing. A high-speed data transfer rate, can automatically increase slowdown. Processing technology to improve the processing and cutting tool life. At present high-speed machine tool manufacturers, usually in the general machine tools on low speed, the feed of the rough and then proceed to heat treatment, the last in the high-speed machine on the half-finished and finished, in improving the accuracy and efficiency at the same time, as far as possible to reduce processing Cost.2.2 High-speed machining toolHigh-speed machining tool is the most active one of the important factors, it has a direct impact on the efficiency of processing, manufacturing costs and product processing and accuracy. Tool in high-speed processing to bear high temperature, high pressure, friction, shock and vibration, such as loading, its hardness and wear-resistance, strength and toughness, heat resistance, technology and economic performance of the basic high-speed processing performance is the key One of the factors. High-speed cutting tool technology development speed, the more applications such as diamond (PCD), cubic boron nitride (CBN), ceramic knives, carbide coating, (C) titanium nitride Carbide TIC (N) And so on. CBN has high hardness, abrasion resistance and the extremely good thermal conductivity, and iron group elements between the great inertia, in 1300 ℃ would not have happened significant role in the chemical, also has a good stability. The experiments show that with CBN cutting toolHRC35 ~ 67 hardness of hardened steel can achieve very high speed. Ceramics have good wear resistance and thermal chemical stability, its hardness, toughness below the CBN, can be used for processing hardness of HRC <5 0 parts. Carbide Tool good wear resistance, but the hardness than the low-CBN and ceramics. Coating technology used knives, cutting tools can improve hardness and cutting the rate, for cutting HRC40 ~ 50 in hardness between the workpiece. Can be used to heat-resistant alloys, titanium alloys, hightemperature alloy, cast iron, Chungang, aluminum and composite materials of high-speed cutting Cut, the most widely used. Precision machining non-ferrous metals or non-metallic materials, or the choice of polycrystalline diamond Gang-coated tool.2.3 High-speed processing technologyHigh-speed cutting technology for high-speed machining is the key. Cutting Methods misconduct, will increase wear tool to less than high-speed processing purposes. Only high-speed machine tool and not a good guide technology, high-speed machining equipment can not fully play its role. In high-speed machining, should be chosen with milling, when the milling cutter involvement with the workpiece chip thickness as the greatest, and then gradually decreased. High-speed machining suitable for shallow depth of cut, cutting depth of not more than 0.2 mm, to avoid the location of deviation tool to ensure that the geometric precision machining parts. Ensure that the workpiece on the cutting constant load, to get good processing quality. Cutting a single high-speed milling path-cutting mode, try not to interrupt the process and cutting tool path, reducing the involvement tool to cut the number to be relatively stable cutting process. Tool to reduce the rapid change to, in other words when the NC machine tools must cease immediately, or Jiangsu, and then implement the next step. As the machine tool acceleration restrictions, easy to cause a waste of time, and exigency stop or radical move would damage the surface accuracy. In the mold of high-speed finishing, in each Cut, cut to the workpiece, the feed should try to change the direction of a curve or arc adapter, avoid a straight line adapter to maintain the smooth process of cutting.3 Die in high-speed milling processing ofMilling as a highly efficient high-speed cutting of the new method,inMould Manufacturing has been widely used. Forging links in the regular production model, with EDM cavity to be 12 ~ 15 h, electrodes produced 2 h. Milling after the switch to high-speed, high-speed milling cutter on the hardness of HRC 6 0 hardened tool steel processing. The forging die processing only 3h20min, improve work efficiency four to five times the processing surface roughness of Ra0.5 ~ 0.6m, fully in line with quality requirements.High-speed cutting technology is cutting technology one of the major developments, mainly used in automobile industry and die industry, particularly in the processing complex surface, the workpiece itself or knives rigid requirements of the higher processing areas, is a range of advanced processing technology The integration, high efficiency and high quality for the people respected. It not only involves high-speed processing technology, but also including high-speed processing machine tools, numerical control system, high-speed cutting tools and CAD / CAM technology. Die-processing technology has been developed in the mold of the manufacturing sector in general, and in my application and the application of the standards have yet to be improved, because of its traditional processing with unparalleled advantages, the future will continue to be an inevitable development of processing technology Direction.4 Numerical control technology and equipping development trend and countermeasureEquip the engineering level, level of determining the whole national economy of the modernized degree and modernized degree of industry, numerical control technology is it develop new developing new high-tech industry and most advanced industry to equip (such as information technology and his industry, biotechnology and his industry, aviation, spaceflight, etc. national defense industry) last technology and getting more basic most equipment. Marx has ever said "the differences of different economic times, do not lie in what is produced, and lie in how to produce, produce with some means of labor ". Manufacturing technology and equipping the most basic means of production that are that the mankind produced the activity, and numerical control technology is nowadays advanced manufacturing technology and equips the most central technology. Nowadays the manufacturing industry all around the world adopts numerical control technology extensively, in order to improve manufacturing capacity and level, improve the adaptive capacity and competitive power to the changeable market of the trends. In addition every industrially developed country in the world also classifies the technology and numerical control equipment of numerical control as the strategic materials of the country, not merely take the great measure to develop one's own numerical control technology and industry, and implement blockading and restrictive policy to our country in view of " high-grade, precision and advanced key technology of numerical control " and equipping. In a word, develop the advanced manufacturing technology taking numerical control technology as the core and already become every world developed country and accelerate economic development in a more cost-effective manner, important way to improve the overall national strength and national position.Numerical control technology is the technology controlled to mechanical movement and working course with digital information, integrated products of electromechanics that the numerical control equipment is the new technology represented by numerical control technology forms to the manufacture industry of the tradition and infiltration of the new developing manufacturing industry, namely the so-called digitization is equipped, its technological range covers a lot of fields: (1)Mechanical manufacturing technology;(2)Information processing, processing, transmission technology; (3)Automatic control technology;(4)Servo drive technology; (5)Technology of the sensor; (6)Software engineering ,etc..Development trend of a numerical control technologyThe application of numerical control technology has not only brought the revolutionary change to manufacturing industry of the tradition, make the manufacturing industry become the industrialized symbol , and with the constant development of numerical control technology and enlargement of the application, the development of some important trades (IT , automobile , light industry , medical treatment ,etc. ) to the national economy and the people's livelihood of his plays a more and more important role, because the digitization that these trades needed to equip has already been the main trend of modern development. Numerical control technology in the world at present and equipping the development trend to see, there is the following several respect [1- ] in its main research focus.5 A high-speed, high finish machining technology and new trend equippedThe efficiency, quality are subjavanufacturing technology. High-speed, high finish machining technology can raise the efficiency greatly , improve the quality and grade of the products, shorten production cycle and improve the market competitive power. Japan carries the technological research association first to classify it as one of the 5 great modern manufacturing technologies for this, learn (CIRP) to confirm it as the centre in the 21st century and study one of the directions in international production engineering.In the field of car industry, produce one second when beat such as production of 300,000 / vehicle per year, and many variety process it is car that equip key problem that must be solved one of; In the fields of aviation and aerospace industry, spare parts of its processing are mostly the thin wall and thin muscle, rigidity is very bad, the material is aluminium or aluminium alloy, only in a situation that cut the speed and cut strength very small high, could process these muscles, walls. Adopt large-scale whole aluminium alloy method that blank " pay empty " make the wing recently, such large-scale parts as the fuselage ,etc. come to substitute a lot of parts to assemble through numerous rivet , screw and other connection way, make the intensity , rigidity and dependability of the component improved. All these, to processing and equipping the demand which has proposed high-speed, high precise and high flexibility.According to EMO2001 exhibition situation, high-speed machining center is it give speed can reach 80m/min is even high , air transport competent speed can up to 100m/min to be about to enter. A lot of automobile factories in the world at present, including Shanghai General Motors Corporation of our country, have already adopted and substituted and made the lathe up with the production line part that the high-speed machining center makes up. HyperMach lathe of U.S.A. CINCINNATI Company enters to nearly biggest 60m/min of speed, it is 100m/min to be fast, the acceleration reaches 2g, the rotational speed of the main shaft has already reached 60 000r/min. Processing a thin wall of plane parts, spend 30min only, and same part general at a high speed milling machine process and take 3h, the ordinary milling machine is being processed to need 8h; The speed and acceleration of main shaft of dual main shaft lathes of Germany DMG Company are up to 120000r/mm and 1g.In machining accuracy, the past 10 years, ordinary progression accuse of machining accuracy of lathe bring 5μm up to from 10μm already, accurate grades of machining center from 3～5μm, rise to 1～1.5μm, and ultraprecision machining accuracy is it e nter nanometer grade to begin already (0.01μm).In dependability, MTBF value of the foreign numerical control device has already reached above 6 000h,MTBF value of the servo system reaches above 30000h, demonstrate very high dependability .In order to realize high-speed, high finish machining, if the part of function related to it is electric main shaft, straight line electrical machinery get fast development, the application is expanded further .5.2 Link and process and compound to process the fast development of the lathe in 5 axesAdopt 5 axles to link the processing of the three-dimensional curved surface part, can cut with the best geometry form of the cutter , not only highly polished, but also efficiency improves by a large margin . It is generally acknowledged, the efficiency of an 5 axle gear beds can equal 2 3 axle gear beds, is it wait for to use the cubic nitrogen boron the milling cutter of ultra hard material is milled and pared at a high speed while quenching the hard steel part, 5 axles link and process 3 constant axles to link and process and give play to higher benefit. Because such reasons as complicated that 5 axles link the numerical control system , host computer structure that but go over, it is several times higher that its price links the numerical control lathe than 3 axles , in addition the technological degree of difficulty of programming is relatively great, have restricted the development of 5 axle gear beds.At present because of electric appearance of main shaft, is it realize 5 axle complex main shaft hair structure processed to link greatly simplify to make, it makes degree of difficulty and reducing by a large margin of the cost, the price disparity of the numerical control system shrinks. So promoted 5 axle gear beds of head of complex main shaft and compound to process the development of the lathe (process the lathe including 5).At EMO2001 exhibition, new Japanese 5 of worker machine process lathe adopt complex main shaft hair, can realize the processing of 4 vertical planes and processing of the wanton angle, make 5 times process and 5 axles are processed and can be realized on the same lathe, can also realize the inclined plane and pour the processing of the hole of awls. Germany DMG Company exhibits the DMUVoution series machining center, but put and insert and put processing and 5 axles 5 times to link and process in once, can be controlled by CNC system or CAD/CAM is controlled directly or indirectly.5.3 Become the main trend of systematic development of contemporary numerical control intelligently, openly, networkedly.The numerical control equipment in the 21st century will be sure the intelligent system, the intelligent content includes all respects in the numerical control system: It is intelligent in order to pursue the efficiency of processing and process quality, control such as the self-adaptation of the processing course, the craft parameter is produced automatically; Join the convenient one in order to improve the performance of urging and use intelligently, if feedforward control , adaptive operation , electrical machinery of parameter , discern load select models , since exactly makes etc. automatically; The ones that simplified programming , simplified operating aspect are intelligent, for instance intelligent automatic programming , intelligent man-machine interface ,etc.; There are content of intelligence diagnose , intelligent monitoring , diagnosis convenient to be systematic and maintaining ,etc..Produce the existing problem for the industrialization of solving the traditional numerical control system sealing and numerical control application software. A lot of countries carry on research to the open numerical control system at present, such as NGC of U.S.A. (The Next Generation Work-Station/MachineControl), OSACA of European Community (Open System Architecture for Control within Automation Systems), OSEC (Open System Environment for Controller) of Japan, ONC (Open Numerical Control System) of China, etc.. The numerical control system melts to become the future way of the numerical control system open. The so-called open numerical control system is the development of the numerical control system can be on unified operation platform, face the lathe producer and end user, through changing, increasing or cutting out the structure target(numerical control function), form the serration, and can use users specially conveniently and the technical know-how is integrated in the control system, realize the open numerical control system of different variety , different grade fast, form leading brand products with distinct distinction. System structure norm of the open numerical control system at present, communication norm , disposing norm , operation platform , numerical control systematic function storehouse and numerical control systematic function software development ,etc. are the core of present research.The networked numerical control equipment is a new light spot of the fair of the internationally famous lathe in the past two years. Meeting production line , manufacture system , demand for the information integration of manufacturing company networkedly greatly of numerical control equipment, realize new manufacture mode such as quick make , fictitious enterprise , basic Entrance that the whole world make too. Some domestic and international famous numerical control lathes and systematic manufacturing companies of numerical control have all introduced relevant new concepts and protons of a machine in the past two years, if in EMO2001 exhibition, " Cyber Production Center " that the company exhibits of mountain rugged campstool gram in Japan (Mazak) (intellectual central production control unit, abbreviated as CPC); The lathe company of Japanese big Wei (Okuma ) exhibits " IT plaza " (the information technology square , is abbreviated as IT square ); Open Manufacturing Environment that the company exhibits of German Siemens (Siemens ) (open the manufacturing environment, abbreviated as OME),etc., have reflected numerical control machine tooling to the development trend of networked direction.5.4 Pay attention to the new technical standard, normal setting-up5.4.1 Design the norm of developing about the numerical control systemAs noted previously, there are better common ability, flexibility, adaptability, expanding in the open numerical control system, such countries as U.S.A. ,European Community and Japan ,etc. implement the strategic development plan one after another , carry on the research and formulation of the systematic norm (OMAC , OSACA , OSEC ) of numerical control of the open system structure, 3 biggest economies in the world have carried on the formulation that nearly the same science planned and standardized in a short time, have indicated a new arrival of period of change of numerical control technology. Our country started the research and formulation of standardizing the frame of ONC numerical control system of China too in 2000.5.4.2 About the numerical control standardThe numerical control standard is a kind of trend of information-based development of manufacturing industry. Information exchange among 50 years after numerical control technology was born was all。
机械加工外文翻译
附录附录1英文原文Basic Machining Operations and Cutting TechnologyBasic Machining OperationsMachine tools have evolved from the early foot-powered lathes of the Egyptians and John Wilkinson's boring mill. They are designed to provide rigid support for both the work piece and the cutting tool and can precisely control their relative positions and the velocity of the tool with respect to the work piece. Basically, in metal cutting, a sharpened wedge-shaped tool removes a rather narrow strip of metal from the surface of a ductile work piece in the form of a severely deformed chip. The chip is a waste product that is considerably shorter than the work piece from which it came but with a corresponding increase in thickness of the uncut chip. The geometrical shape of work piece depends on the shape of the tool and its path during the machining operation.Most machining operations produce parts of differing geometry. If a rough cylindrical work piece revolves about a central axis and the tool penetrates beneath its surface and travels parallel to the center of rotation, a surface of revolution is produced, and the operation is called turning. If a hollow tube is machined on the inside in a similar manner, the operation is called boring. Producing an external conical surface uniformly varying diameter is called taper turning, if the tool point travels in a path of varying radius, a contoured surface like that of a bowling pin can be produced; or, if the piece is short enough and the support is sufficiently rigid, a contoured surface could be produced by feeding a shaped tool normal to the axis of rotation. Short tapered or cylindrical surfaces could also be contour formed.Flat or plane surfaces are frequently required. They can be generated by radial turning or facing, in which the tool point moves normal to the axis of rotation. In other cases, it is more convenient to hold the work piece steady and reciprocate the tool across it in a series of straight-line cuts with a crosswise feed increment before each cutting stroke. This operation is called planning and is carried out on a shaper. For larger pieces it is easier to keep the tool stationary and draw the work piece under it as in planning. The tool is fed at each reciprocation. Contoured surfaces can be produced by using shaped tools.Multiple-edged tools can also be used. Drilling uses a twin-edged fluted tool for holes with depths up to 5 to 10 times the drill diameter. Whether thedrill turns or the work piece rotates, relative motion between the cutting edge and the work piece is the important factor. In milling operations a rotary cutter with a number of cutting edges engages the work piece. Which moves slowly with respect to the cutter. Plane or contoured surfaces may be produced, depending on the geometry of the cutter and the type of feed. Horizontal or vertical axes of rotation may be used, and the feed of the work piece may be in any of the three coordinate directions.Basic Machine ToolsMachine tools are used to produce a part of a specified geometrical shape and precise I size by removing metal from a ductile material in the form of chips. The latter are a waste product and vary from long continuous ribbons of a ductile material such as steel, which are undesirable from a disposal point of view, to easily handled well-broken chips resulting from cast iron. Machine tools perform five basic metal-removal processes: I turning, planning, drilling, milling, and grinding. All other metal-removal processes are modifications of these five basic processes. For example, boring is internal turning; reaming, tapping, and counter boring modify drilled holes and are related to drilling; bobbing and gear cutting are fundamentally milling operations; hack sawing and broaching are a form of planning and honing; lapping, super finishing. Polishing and buffing are variants of grinding or abrasive removal operations. Therefore, there are only four types of basic machine tools, which use cutting tools of specific controllable geometry: 1. lathes, 2. planers, 3. drilling machines, and 4. milling machines. The grinding process forms chips, but the geometry of the abrasive grain is uncontrollable.The amount and rate of material removed by the various machining processes may be I large, as in heavy turning operations, or extremely small, as in lapping or super finishing operations where only the high spots of a surface are removed.A machine tool performs three major functions: 1. it rigidly supports the work piece or its holder and the cutting tool; 2. it provides relative motion between the work piece and the cutting tool; 3. it provides a range of feeds and speeds usually ranging from 4 to 32 choices in each case.Speed and Feeds in MachiningSpeeds, feeds, and depth of cut are the three major variables for economical machining. Other variables are the work and tool materials, coolant and geometry of the cutting tool. The rate of metal removal and power required for machining depend upon these variables.The depth of cut, feed, and cutting speed are machine settings that must be established in any metal-cutting operation. They all affect the forces, the power, and the rate of metal removal. They can be defined by comparing them to the needle and record of a phonograph. The cutting speed (V) is represented by the velocity of- the record surface relative to the needle in the tone arm at any instant. Feed is represented by the advance of the needle radially inward perrevolution, or is the difference in position between two adjacent grooves. The depth of cut is the penetration of the needle into the record or the depth of the grooves.Turning on Lathe CentersThe basic operations performed on an engine lathe are illustrated. Those operations performed on external surfaces with a single point cutting tool are called turning. Except for drilling, reaming, and lapping, the operations on internal surfaces are also performed by a single point cutting tool.All machining operations, including turning and boring, can be classified as roughing, finishing, or semi-finishing. The objective of a roughing operation is to remove the bulk of the material as rapidly and as efficiently as possible, while leaving a small amount of material on the work-piece for the finishing operation. Finishing operations are performed to obtain the final size, shape, and surface finish on the work piece. Sometimes a semi-finishing operation will precede the finishing operation to leave a small predetermined and uniform amount of stock on the work-piece to be removed by the finishing operation.Generally, longer work pieces are turned while supported on one or two lathe centers. Cone shaped holes, called center holes, which fit the lathe centers are drilled in the ends of the work piece-usually along the axis of the cylindrical part. The end of the work piece adjacent to the tail stock is always supported by a tail stock center, while the end near the head stock may be supported by a head stock center or held in a chuck. The head stock end of the work piece may be held in a four-jaw chuck, or in a type chuck. This method holds the work piece firmly and transfers the power to the work piece smoothly; the additional support to the work piece provided by the chuck lessens the tendency for chatter to occur when cutting. Precise results can be obtained with this method if care is taken to hold the work piece accurately in the chuck.Very precise results can be obtained by supporting the work piece between two centers. A lathe dog is clamped to the work piece; together they are driven by a driver plate mounted on the spindle nose. One end of the Work piece is mecained;then the work piece can be turned around in the lathe to machine the other end. The center holes in the work piece serve as precise locating surfaces as well as bearing surfaces to carry the weight of the work piece and to resist the cutting forces. After the work piece has been removed from the lathe for any reason, the center holes will accurately align the work piece back in the lathe or in another lathe, or in a cylindrical grinding machine. The work piece must never be held at the head stock end by both a chuck and a lathe center. While at first thought this seems like a quick method of aligning the work piece in the chuck, this must not be done because it is not possible to press evenly with the jaws against the work piece while it is also supported by the center. The alignment provided by the center will not be maintained and the pressure of the jaws may damage the center hole, the lathe center, andperhaps even the lathe spindle. Compensating or floating jaw chucks used almost exclusively on high production work provide an exception to the statements made above. These chucks are really work drivers and cannot be used for the same purpose as ordinary three or four-jaw chucks.While very large diameter work pieces are sometimes mounted on two centers, they are preferably held at the headstock end by faceplate jaws to obtain the smooth power transmission; moreover, large lathe dogs that are adequate to transmit the power not generally available, although they can be made as a special. Faceplate jaws are like chuck jaws except that they are mounted on a faceplate, which has less overhang from the spindle bearings than a large chuck would have.Introduction of MachiningMachining as a shape-producing method is the most universally used and the most important of all manufacturing processes. Machining is a shape-producing process in which a power-driven device causes material to be removed in chip form. Most machining is done with equipment that supports both the work piece and cutting tool although in some cases portable equipment is used with unsupported work piece.Low setup cost for small Quantities. Machining has two applications in manufacturing. For casting, forging, and press working, each specific shape to be produced, even one part, nearly always has a high tooling cost. The shapes that may he produced by welding depend to a large degree on the shapes of raw material that are available. By making use of generally high cost equipment but without special tooling, it is possible, by machining; to start with nearly any form of raw material, so tong as the exterior dimensions are great enough, and produce any desired shape from any material. Therefore .machining is usually the preferred method for producing one or a few parts, even when the design of the part would logically lead to casting, forging or press working if a high quantity were to be produced.Close accuracies, good finishes. The second application for machining is based on the high accuracies and surface finishes possible. Many of the parts machined in low quantities would be produced with lower but acceptable tolerances if produced in high quantities by some other process. On the other hand, many parts are given their general shapes by some high quantity deformation process and machined only on selected surfaces where high accuracies are needed. Internal threads, for example, are seldom produced by any means other than machining and small holes in press worked parts may be machined following the press working operations.Primary Cutting ParametersThe basic tool-work relationship in cutting is adequately described by means of four factors: tool geometry, cutting speed, feed, and depth of cut.The cutting tool must be made of an appropriate material; it must be strong, tough, hard, and wear resistant. The tool s geometry characterized by planes and angles, must be correct for each cutting operation. Cutting speed is the rate at which the work surface passes by the cutting edge. It may be expressed in feet per minute.For efficient machining the cutting speed must be of a magnitude appropriate to the particular work-tool combination. In general, the harder the work material, the slower the speed.Feed is the rate at which the cutting tool advances into the work piece. "Where the work piece or the tool rotates, feed is measured in inches per revolution. When the tool or the work reciprocates, feed is measured in inches per stroke, Generally, feed varies inversely with cutting speed for otherwise similar conditions.The depth of cut, measured inches is the distance the tool is set into the work. It is the width of the chip in turning or the thickness of the chip in a rectilinear cut. In roughing operations, the depth of cut can be larger than for finishing operations.The Effect of Changes in Cutting Parameters on Cutting TemperaturesIn metal cutting operations heat is generated in the primary and secondary deformation zones and these results in a complex temperature distribution throughout the tool, work piece and chip. A typical set of isotherms is shown in figure where it can be seen that, as could be expected, there is a very large temperature gradient throughout the width of the chip as the work piece material is sheared in primary deformation and there is a further large temperature in the chip adjacent to the face as the chip is sheared in secondary deformation. This leads to a maximum cutting temperature a short distance up the face from the cutting edge and a small distance into the chip.Since virtually all the work done in metal cutting is converted into heat, it could be expected that factors which increase the power consumed per unit volume of metal removed will increase the cutting temperature. Thus an increase in the rake angle, all other parameters remaining constant, will reduce the power per unit volume of metal removed and the cutting temperatures will reduce. When considering increase in unreformed chip thickness and cutting speed the situation is more complex. An increase in undeformed chip thickness tends to be a scale effect where the amounts of heat which pass to the work piece, the tool and chip remain in fixed proportions and the changes in cutting temperature tend to be small. Increase in cutting speed; however, reduce the amount of heat which passes into the work piece and this increase the temperature rise of the chip m primary deformation. Further, the secondary deformation zone tends to be smaller and this has the effect of increasing the temperatures in this zone. Other changes in cutting parameters have virtually no effect on the power consumed per unit volume of metal removed and consequently have virtually no effect on the cutting temperatures. Since ithas been shown that even small changes in cutting temperature have a significant effect on tool wear rate it is appropriate to indicate how cutting temperatures can be assessed from cutting data.The most direct and accurate method for measuring temperatures in high -speed-steel cutting tools is that of Wright &. Trent which also yields detailed information on temperature distributions in high-speed-steel cutting tools. The technique is based on the metallographic examination of sectioned high-speed-steel tools which relates microstructure changes to thermal history.Trent has described measurements of cutting temperatures and temperature distributions for high-speed-steel tools when machining a wide range of work piece materials. This technique has been further developed by using scanning electron microscopy to study fine-scale microstructure changes arising from over tempering of the tempered martens tic matrix of various high-speed-steels. This technique has also been used to study temperature distributions in both high-speed -steel single point turning tools and twist drills.Wears of Cutting ToolDiscounting brittle fracture and edge chipping, which have already been dealt with, tool wear is basically of three types. Flank wear, crater wear, and notch wear. Flank wear occurs on both the major and the minor cutting edges. On the major cutting edge, which is responsible for bulk metal removal, these results in increased cutting forces and higher temperatures which if left unchecked can lead to vibration of the tool and work piece and a condition where efficient cutting can no longer take place. On the minor cutting edge, which determines work piece size and surface finish, flank wear can result in an oversized product which has poor surface finish. Under most practical cutting conditions, the tool will fail due to major flank wear before the minor flank wear is sufficiently large to result in the manufacture of an unacceptable component.Because of the stress distribution on the tool face, the frictional stress in the region of sliding contact between the chip and the face is at a maximum at the start of the sliding contact region and is zero at the end. Thus abrasive wear takes place in this region with more wear taking place adjacent to the seizure region than adjacent to the point at which the chip loses contact with the face. This result in localized pitting of the tool face some distance up the face which is usually referred to as catering and which normally has a section in the form of a circular arc. In many respects and for practical cutting conditions, crater wear is a less severe form of wear than flank wear and consequently flank wear is a more common tool failure criterion. However, since various authors have shown that the temperature on the face increases more rapidly with increasing cutting speed than the temperature on the flank, and since the rate of wear of any type is significantly affected by changes in temperature, crater wear usually occurs at high cutting speeds.At the end of the major flank wear land where the tool is in contact with the uncut work piece surface it is common for the flank wear to be more pronounced than along the rest of the wear land. This is because of localised effects such as a hardened layer on the uncut surface caused by work hardening introduced by a previous cut, an oxide scale, and localised high temperatures resulting from the edge effect. This localised wear is usually referred to as notch wear and occasionally is very severe. Although the presence of the notch will not significantly affect the cutting properties of the tool, the notch is often relatively deep and if cutting were to continue there would be a good chance that the tool would fracture.If any form of progressive wear allowed to continue, dramatically and the tool would fail catastrophically, i. e. the tool would be no longer capable of cutting and, at best, the work piece would be scrapped whilst, at worst, damage could be caused to the machine tool. For carbide cutting tools and for all types of wear, the tool is said to have reached the end of its useful life long before the onset of catastrophic failure. For high-speed-steel cutting tools, however, where the wear tends to be non-uniform it has been found that the most meaningful and reproducible results can be obtained when the wear is allowed to continue to the onset of catastrophic failure even though, of course, in practice a cutting time far less than that to failure would be used. The onset of catastrophic failure is characterized by one of several phenomena, the most common being a sudden increase in cutting force, the presence of burnished rings on the work piece, and a significant increase in the noise level.Mechanism of Surface Finish ProductionThere are basically five mechanisms which contribute to the production of a surface which have been machined. These are:(l) The basic geometry of the cutting process. In, for example, single point turning the tool will advance a constant distance axially per revolution of the workpiecc and the resultant surface will have on it, when viewed perpendicularly to the direction of tool feed motion, a series of cusps which will have a basic form which replicates the shape of the tool in cut.(2) The efficiency of the cutting operation. It has already been mentioned that cutting with unstable built-up-edges will produce a surface which contains hard built-up-edge fragments which will result in a degradation of the surface finish. It can also be demonstrated that cutting under adverse conditions such as apply when using large feeds small rake angles and low cutting speeds, besides producing conditions which lead to unstable built-up-edge production, the cutting process itself can become unstable and instead of continuous shear occurring in the shear zone, tearing takes place, discontinuous chips of uneven thickness are produced, and the resultant surface is poor. This situation is particularly noticeable when machining very ductile materials such as copper and aluminum.(3) The stability of the machine tool. Under some combinations of cutting conditions; work piece size, method of clamping ,and cutting tool rigidity relative to the machine tool structure, instability can be set up in the tool which causes it to vibrate. Under some conditions this vibration will reach and maintain steady amplitude whilst under other conditions the vibration will built up and unless cutting is stopped considerable damage to both the cutting tool and work piece may occur. This phenomenon is known as chatter and in axial turning is characterized by long pitch helical bands on the work piece surface and short pitch undulations on the transient machined surface.(4)The effectiveness of removing swarf. In discontinuous chip production machining, such as milling or turning of brittle materials, it is expected that the chip (swarf) will leave the cutting zone either under gravity or with the assistance of a jet of cutting fluid and that they will not influence the cut surface in any way. However, when continuous chip production is evident, unless steps are taken to control the swarf it is likely that it will impinge on the cut surface and mark it. Inevitably, this marking besides looking.(5)The effective clearance angle on the cutting tool. For certain geometries of minor cutting edge relief and clearance angles it is possible to cut on the major cutting edge and burnish on the minor cutting edge. This can produce a good surface finish but, of course, it is strictly a combination of metal cutting and metal forming and is not to be recommended as a practical cutting method. However, due to cutting tool wear, these conditions occasionally arise and lead to a marked change in the surface characteristics.Limits and TolerancesMachine parts are manufactured so they are interchangeable. In other words, each part of a machine or mechanism is made to a certain size and shape so will fit into any other machine or mechanism of the same type. To make the part interchangeable, each individual part must be made to a size that will fit the mating part in the correct way. It is not only impossible, but also impractical to make many parts to an exact size. This is because machines are not perfect, and the tools become worn. A slight variation from the exact size is always allowed. The amount of this variation depends on the kind of part being manufactured. For examples part might be made 6 in. long with a variation allowed of 0.003 (three-thousandths) in. above and below this size. Therefore, the part could be 5.997 to 6.003 in. and still be the correct size. These are known as the limits. The difference between upper and lower limits is called the tolerance.A tolerance is the total permissible variation in the size of a part.The basic size is that size from which limits of size arc derived by the application of allowances and tolerances.Sometimes the limit is allowed in only one direction. This is known as unilateral tolerance.Unilateral tolerancing is a system of dimensioning where the tolerance (that is variation) is shown in only one direction from the nominal size. Unilateral tolerancing allow the changing of tolerance on a hole or shaft without seriously affecting the fit.When the tolerance is in both directions from the basic size it is known as a bilateral tolerance (plus and minus).Bilateral tolerancing is a system of dimensioning where the tolerance (that is variation) is split and is shown on either side of the nominal size. Limit dimensioning is a system of dimensioning where only the maximum and minimum dimensions arc shown. Thus, the tolerance is the difference between these two dimensions.Surface Finishing and Dimensional ControlProducts that have been completed to their proper shape and size frequently require some type of surface finishing to enable them to satisfactorily fulfill their function. In some cases, it is necessary to improve the physical properties of the surface material for resistance to penetration or abrasion. In many manufacturing processes, the product surface is left with dirt .chips, grease, or other harmful material upon it. Assemblies that are made of different materials, or from the same materials processed in different manners, may require some special surface treatment to provide uniformity of appearance.Surface finishing may sometimes become an intermediate step processing. For instance, cleaning and polishing are usually essential before any kind of plating process. Some of the cleaning procedures are also used for improving surface smoothness on mating parts and for removing burrs and sharp corners, which might be harmful in later use. Another important need for surface finishing is for corrosion protection in a variety of: environments. The type of protection procedure will depend largely upon the anticipated exposure, with due consideration to the material being protected and the economic factors involved.Satisfying the above objectives necessitates the use of main surface-finishing methods that involve chemical change of the surface mechanical work affecting surface properties, cleaning by a variety of methods, and the application of protective coatings, organic and metallic.In the early days of engineering, the mating of parts was achieved by machining one part as nearly as possible to the required size, machining the mating part nearly to size, and then completing its machining, continually offering the other part to it, until the desired relationship was obtained. If it was inconvenient to offer one part to the other part during machining, the final work was done at the bench by a fitter, who scraped the mating parts until the desired fit was obtained, the fitter therefore being a 'fitter' in the literal sense. J It is obvious that the two parts would have to remain together, and m the event of one having to be replaced, the fitting would have to be done all over again. In these days, we expect to be able to purchase a replacement fora broken part, and for it to function correctly without the need for scraping and other fitting operations.When one part can be used 'off the shelf' to replace another of the same dimension and material specification, the parts are said to be interchangeable. A system of interchangeability usually lowers the production costs as there is no need for an expensive, 'fiddling' operation, and it benefits the customer in the event of the need to replace worn parts.Automatic Fixture DesignTraditional synchronous grippers for assembly equipment move parts to the gripper centre-line, assuring that the parts will be in a known position after they arc picked from a conveyor or nest. However, in some applications, forcing the part to the centre-line may damage cither the part or equipment. When the part is delicate and a small collision can result in scrap, when its location is fixed by a machine spindle or mould, or when tolerances are tight, it is preferable to make a gripper comply with the position of the part, rather than the other way around. For these tasks, Zaytran Inc. Of Elyria, Ohio, has created the GPN series of non- synchronous, compliant grippers. Because the force and synchronizations systems of the grippers are independent, the synchronization system can be replaced by a precision slide system without affecting gripper force. Gripper sizes range from 51b gripping force and 0.2 in. stroke to 40Glb gripping force and 6in stroke. GrippersProduction is characterized by batch-size becoming smaller and smaller and greater variety of products. Assembly, being the last production step, is particularly vulnerable to changes in schedules, batch-sizes, and product design. This situation is forcing many companies to put more effort into extensive rationalization and automation of assembly that was previouslyextensive rationalization and automation of assembly that was previously the case. Although the development of flexible fixtures fell quickly behind the development of flexible handling systems such as industrial robots, there are, nonetheless promising attempts to increase the flexibility of fixtures. The fact that fixtures are the essential product - specific investment of a production system intensifies the economic necessity to make the fixture system more flexible.Fixtures can be divided according to their flexibility into special fixtures, group fixtures, modular fixtures and highly flexible fixtures. Flexible fixtures are characterized by their high adaptability to different work pieces, and by low change-over time and expenditure.There are several steps required to generate a fixture, in which a work piece is fixed for a production task. The first step is to define the necessary position of the work piece in the fixture, based on the unmachined or base pan, and the working features. Following this, a combination of stability planes must be selected. These stability planes constitute the fixture configuration in which the work piece is fixed in the defined position, all the forces or torques are compensated,。
机械外文翻译中英文002
xxxxxx大学毕业设计（论文）外文文献（翻译）学院xxxxxxxxxxxxxxxx专业班级xxxxxxxx学生姓名xxxxxxx指导教师xxxxx附录2中文翻译基本加工工序和切削技术机床是从早期的埃及人的脚踏动力车和约翰·威尔金森的镗床发展而来的。
它们为工件和刀具提供刚性支撑并可以精确控制它们的相对位置和相对速度。
基本上讲，金属切削是指一个磨尖的锲形工具从有韧性的工件表面上去除一条很窄的金属。
切屑是被废弃的产品，与其它工件相比切屑较短，但对于未切削部分的厚度有一定的增加。
工件表面的几何形状取决于刀具的形状以及加工操作过程中刀具的路径。
大多数加工工序产生不同几何形状的零件。
如果一个粗糙的工件在中心轴上转动并且刀具平行于旋转中心切入工件表面，一个旋转表面就产生了，这种操作称为车削。
如果一个空心的管子以同样的方式在内表面加工，这种操作称为镗孔。
当均匀地改变直径时便产生了一个圆锥形的外表面，这称为锥度车削。
如果刀具接触点以改变半径的方式运动，那么一个外轮廓像球的工件便产生了；或者如果工件足够的短并且支撑是十分刚硬的，那么成型刀具相对于旋转轴正常进给的一个外表面便可产生，短锥形或圆柱形的表面也可形成。
平坦的表面是经常需要的，它们可以由刀具接触点相对于旋转轴的径向车削产生。
在刨削时对于较大的工件更容易将刀具固定并将工件置于刀具下面。
刀具可以往复地进给。
成形面可以通过成型刀具加工产生。
多刃刀具也能使用。
使用双刃槽钻钻深度是钻孔直径5-10倍的孔。
不管是钻头旋转还是工件旋转，切削刃与工件之间的相对运动是一个重要因数。
在铣削时一个带有许多切削刃的旋转刀具与工件接触，工件相对刀具慢慢运动。
平的或成形面根据刀具的几何形状和进给方式可能产生。
可以产生横向或纵向轴旋转并且可以在任何三个坐标方向上进给。
基本机床机床通过从塑性材料上去除屑片来产生出具有特别几何形状和精确尺寸的零件。
后者是废弃物，是由塑性材料如钢的长而不断的带状物变化而来，从处理的角度来看，那是没有用处的。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
外文资料翻译译文从生态加工技术对攻丝的研究摘要这项研究是关于攻螺纹（扭矩，攻丝，磨损，工作硬度等）的加工特性。
在生态加工技术操作下，涂有TiN的MMC（铝合金金属复合材料）攻螺丝形成的攻丝得到了调查，并与没有涂层的特性进行了比较。
下面的结果就是从这份研究中得到的：1.TiN涂层攻丝的刀具寿命是没有攻丝的四倍；2.有TiN涂层的攻丝形成的螺纹比没有的加工硬化要低。
关键词：攻丝；攻螺丝；螺纹；生态加工；钻孔1．引言螺栓、螺钉机械连接中的螺纹是机械部件的最重要紧固系统之一。
螺纹制造有很多种方法，特别攻螺丝是用来生产内螺纹的有效的技术。
最近，每年都强调增加生产力。
据说现在的车间里，最重要和最严重的问题是提高生产力。
怎样改善孔加工（钻/铰孔和攻丝）已成为一个严重的问题。
传统的刀具材料限制了生产力的提高，如高速钢刀具加工铝合金金属复合材料（MMC）时刀具寿命很短由于碳化硅粒子的腐蚀天性。
因此，刀具的磨损和破坏阻碍了生产力的提高。
为了实现理想的生产力，攻丝已经吸引了车间工程师的注意。
在这项研究中，用攻丝加工MMC，利用攻丝（扭矩，攻丝磨损，工作硬度等）的切割特点，有TiN涂层和没有涂层的都进行了调查。
2. 实验方法2.1实验装置攻丝试验在辛辛那提5’NC-MC (5HP)进行。
该（钻孔和攻丝）仪器和数据采集系统如图2.1。
切削力（推力和扭矩）测定使用三个类型9273 压电电力测功器和相应的场所用5007电荷放大器放大。
得到的信号，然后传递到A / D转换器AZI-16-12 ，连接到个人电脑。
切削力测量安装如图2.2。
2.2工件，钻及塔在本实验中使用的工件是铝合金（2618 MMC）的增强，15％碳化硅颗粒。
形成无槽丝锥的螺纹是M10如图2.3和两种类型的攻丝被用来在调查过程中。
攻丝的形状类似于螺钉的形状（M10，孔距1.5），无论有没有氮化钛涂层。
定位孔的直径9.3mm，用于所有试验和聚晶金刚石攻丝钻孔（高速钢硬质合金碳化钨和聚晶金刚石钻孔）用在所有测试。
本实验中用的钻头如图2.4。
图2.1 窃听器和数据采集仪器图2.2 Schmatic图的窃听系统图2.3 水龙头用于这项工作2.3仪表和检测方法的线程线程的估计是用螺纹规来衡量。
结果被分为A等和B等[ 1 ]。
硬铝合金[ 2 ]螺纹深度是攻丝直径的1.4倍。
甲等-质量：直径通过整个螺纹测量。
乙等-质量：直径至少15毫米。
图2.5是显示的直径指标(M10×1.5 ISO 6H)。
2.4实验特性攻丝试验时，切削速度（攻丝的转速）是215 rpm和进给速度0.1mm/rev （322.5mm/min）。
冷却油（氯和硫免费热切割石油）手动供应。
3.实验结果与讨论在M10攻丝操作的推力和扭矩信号显示在图3.1 。
结果表明，随着螺纹扣数的形成，扭矩增大，离开孔时减小。
然而，可以看到几乎没有推力的增加。
图2.4 形状的聚晶金刚石钻头图2.5 螺纹规3.1转矩比较图3.2显示是先前所提到的有TiN涂层和没有涂层的第1孔和第8孔攻丝的扭矩信号。
图2.1 参数确定图3.1 图切削力信号根据窃听测试扭矩图3.2 比较扭矩信号（第1洞和第8洞）与扭矩在攻丝操作的初始阶段显示推力和扭矩的增加。
然而，当螺纹成形进入全速时，推力显示出下降的趋势伴随着扭矩的增加和攻丝缩回，在螺纹孔口也可以看到负扭矩的出现。
图3.1负推力值是攻丝偏离中心的结果是因为一方不正当的工件，刀具的安装或定位空的表面粗糙度。
上述不确定的因素是定位孔的表面粗糙度。
当有TiN涂层第一孔的攻螺纹的攻丝扭矩值8.7 Nm而没有涂层的值是11.2Nm，得到扭矩信号。
因而，第一孔有涂层的相比没有涂层的扭矩减少了28 ％。
而对第8孔有TiN 涂层的扭矩相比没有涂层减少了52 ％。
初始阶段和在攻丝突破点前扭矩信号的比较表明，没有涂层的攻丝扭矩减少要明显于有TiN涂层的攻丝。
可以说，就形成的攻丝而言，在车螺纹时工作是均匀分布在刮削端。
扭矩的比较结果总结在图3.3 。
结果表明，有TiN涂层的攻丝扭矩一般低于那些没有涂层的攻丝。
3.2螺纹形式的比较有TiN涂层和没有涂层的攻丝的螺纹形式如图3.4 。
在螺纹孔①，②，③，④位置的横截面的放大图像以及1，4，8号孔作了比较。
图3.4是不同位置螺纹的照片模型，而图3.5是八号孔放大的图像。
可以从图3.5 中看出，有TiN涂层攻丝形成的螺纹的侧面①②没有异常。
相反，没有涂层表明孔的进口和出口相应的①号和④号位置无规律。
图3.3 比较扭矩信号同类型图3.4 阐明的轴向截面建制线程为了验证上述的意见，对孔①和②进行详细的分析进行。
结果总结在图3.6 。
图3.6（a）和（b）给出了1号和8号螺纹孔各自的①和②位置的结果。
可以观察图3.6（a），有TiN涂层的攻丝齿形远远优于没有涂层的。
3.3比较加工硬化当采用有TiN涂层和没有涂层的攻丝车螺纹时，研究比较加工硬化的严重性。
本研究结果归纳于图3.7 。
选用了两种类型中1号攻丝。
有TiN涂层和没有涂层的结果分别在图3.7（a）和（b）。
用能受100 gw的硬度测量硬度仪测量硬度。
结果表明，有TiN涂层的攻螺纹的硬度低于没有涂层的。
上述结果表明，在以下几个方面，如螺纹形式和加工硬化等，有TiN涂层的攻丝优于没有涂层的攻丝。
图3.5 比较线程形式图3.6 比较扩大线程形式3.4刀具寿命的比较有TiN涂层和没有涂层的攻丝被用来调查性能和攻丝的刀具寿命一样高。
每种类型的攻丝反复进行3次试验，。
结果总结在图3.8 。
螺纹规读数用A,B值评估。
结果表明，在刀具寿命达到限制前，螺纹孔的平均数，是没有TiN涂层攻丝的X = 13和有涂层攻丝的X = 49。
有TiN涂层攻丝的刀具寿命是没有涂层的3.8倍。
3.5比较塔磨损图3.9显示各种类型攻丝的刀具磨损，在实验中车螺纹后如图3.8所示。
应当指出的是，所有用于比较的攻丝已充分达到刀具寿命。
有TiN涂层和没有涂层的攻丝分别如图3.9（a）和（b），。
可以看出，所有攻丝的刀具磨损点。
此外，可以看到大量的磨损在分界线上。
有TiN涂层和没有涂层攻丝的比较，如放大点，结果表明，后者的磨损明显高于前者。
就有TiN涂层攻丝来说，在刀具磨损区可以看到覆盖的TiN涂层。
图3.7 比较硬度分布图3.8 用攻丝的刀具寿命的比较图3.9 用攻丝的刀具磨损比较4.结论4.1有TiN涂层的刀具的寿命大约是没有涂层的刀具寿命的4倍。
4.2和没有TiN涂层的刀具相比，有涂层刀具的扭转力下降了28 ％。
4.3和没有TiN涂层的刀具相比，带有涂层的齿形螺纹刀具则显示出更少的不规则性。
4.4有TiN涂层的刀具的硬度低于没有涂层的刀具。
4.5从以上结果显示，有TiN涂层的刀具在以下方面优于没有涂层的刀具：刀具寿命，螺纹样式和加工硬化等。
参考文献[1] WOLFGANGSTRACHE : Alternative Strategies for the Production of Threads in Aluminum-based SICReinforced Metal Matrix Composite (MMC) Alloy,1993.[2] Beitz.W : Dubbel-Taschhenbuch fuer den Maschinenbau. ISBN 3-540-52381-2, (1990), G15.外文原文A Study on Tapping Viewed from Eco-Machining TechnologyAbstractThis study deals with machining characteristics of thread tapping (torque, tap, wear, workhardness etc.) The tapping of MMC (aluminum alloy metal matrix composite) with TiN coated forming taps under eco-machining technology operation, where chips are not produced and ejected from the tap flute, was investigated and compared with the characteristics during uncoated tapping. The following results are obtained from this study. 1.The tool life of TiN coated taps was 4 times longer than that of uncoated tap；2.Threads formed with the TiN coated taps exhibit lower work hardening than those formed with uncoated taps.Keywords:Tap；Tapping；Thread；Eco-Machining；Drilling1. IntroductionThreads form the mechanical joint of a bolt–screw connection, which is one of the most important fastening systems for mechanical components. There are many ways of thread making,especially that of tapping which has been employed as an efficient technique for the production of internal threads.Recently, the rise of productivity has been emphasized year by year. Also it is said that the improvement of productivity is one of the most important and serious problem in today’s machine shops. The improvement of hole making production (drilling/reaming and tapping) has become a serious matter. One factor limiting productivity gains has been that conventional tool materials such as HSS exhibit very short tool lives when machining an aluminum alloy metal matrix composite (MMC) due to the abrasive nature of the SiC particles. Therefore, the improvement has been obstructed by various problems as rapid tool wear and failure. As a mean of achieving the desired productivity gains, forming taps have caught the attention of machine shop engineers.In this study, cutting characteristics of tapping (torque, taps wear, work hardness, etc.) during the tapping of MMC with forming taps, both TiN coated and uncoated was investigated.2. Experimental Methods2.1 Experimental EquipmentThe tapping tests were conducted on a Cincinati 5’NC-MC (5HP). The (drilling and tapping) apparatus and data acquisition system are presented in Figure 2.1. The cutting forces (thrust and torque) were measured using a three component Kistler Type 9273 Piezo-electric dynamometer and the corresponding locus was amplified by a Kistler type 5007 charge amplifier. The signal obtained was then passed to a Towa A/D converter type AZI-16-12, connected to a personal computer. A schematic diagram of the cutting force measuring setup is presented in Figure 2.2.2.2 Workpiece, Drill and TapThe workpiece used in this experiment is aluminum alloy (2618 MMC) reinforced with 15 vol% silicon carbide (SiC) particulate. The thread forming fluteless taps were M10 as shown in Figure 2.3 and two types of taps were used during the course of the investigation.The shape of the taps was similar to the shape of a screw (M10, Pitch:1.5), either uncoated or coated with Titanium nitride (TiN).Pilot holes of 9.3mm diameter were used for all trials and PCD tipped drills (HSS cemented tungsten carbide and polycrystalline diamond drilling) were employed in all the tests. The shape of drill used in this test is shown in Figure 2.4.2.3 Gauge and Inspection Method of ThreadThe estimate of threads was performed with a thread gauge (Go-NoGo gauge).The results were classified as A and B quality[1]. Where, 1.4×tapped diameter is Diameter is the recommended depth of thread of hard Aluminum alloy[2].A – quality : Gauge can be turned through the whole thread.B – quality : Gauge can be turned in at least 15mm.Figure 2.5 shows the appearance of gauge (M10×1.5 ISO 6H).2.4 Experimental CharacteristicsTapping tests were conducted at a cutting speed (rotational speed of tap) of 215 rpm and feed rate of 0.1mm/rev (322.5mm/min). Coolant oil (Chlorine and sulphur free heat cutting oil) was supplied manually.3. Experimental Results And DiscussionCutting Forces in Tapping (thrust, torque) The thrust and torque signals produced in this tapping operation with a M10 tap are shown in Figure 3.1. The results show that torque increases with number of threads formed and decreases at the instant that the tap is about to break through the outlet of the hole. Whereas, little increase in thrust can be observed.3.1 Comparison of TorqueFigure 3.2 shows torque signals of tap in the 1st hole and 8th holes for the TiN-coated and uncoated taps mentioned in the previous section.At the initial stage of the tapping operation both thrust and torque show an increase in magnitude. However, when the thread forming operation enters full gear, the thrust force shows a decreasing trend accompanied with in increase in torque and as the tap retracts after breakthrough, a negative torque of 5N magnitude can be observed across a few threads at hole outlet.The negative thrust value observed in Figure 3.1 is the outcome of the deflection of the tap from the center due to either improper workpiece, tool setup or poor finish of the pilot holes. The inconclusive results observed above led to the investigating of the factors responsible for the poor finish of the pilot holes.The torque signals derived while threading taps for the 1st hole show tapping torque values of 8.7 Nm for the TiN coated tap and11.2 Nm for the uncoated and tap respectively. Thus, for the1st hole, the TiN coated tap exhibits a 28% reduction in torque compared to the uncoated tap. While for the 8th hole the reduction in torque for the TiN coated tap is approximately 52% as compared to uncoated tap.Comparison of the torque signals at the initial phase and prior to breakthrough of the taps shows that the uncoated tap exhibits a sharper decrease in torque than the TiN coated tap. It can be said that, in the case of forming taps, work is evenly distributed at the scrape point during threading.A comparison of the torque results is summarized in Figure 3.3. Results indicate that tapping torque of the TiN coated tap is generally lower than those of the un-coated tap.3.2 Comparison of Thread FormsThe thread forms for the TiN coated and uncoated taps are shown in Figure 3.4. Magnified images of the axial cross-section of the formed threads at position No.①,②③ and ④ in holesand 1.4 and 8 were used in the comparison.Figure 3.4 is a model of the photographed threads at the various positions, while Figure 3.5 shows magnified images for hole No.8As it can be seen from Figure 3.5, the thread profile at position No.① to ② of threads formed with the TiN coated tap show no abnormalities. On the contrary, with the uncoatedtaps the root shows irregularities at position No.① and ④ corresponding to the hole inlet and outlet.In order to validate the observations mentioned above, a detailed analysis was performed on holes No.① and ②. Results are summarized in Figure 3.6. Figure 3.6(a) and (b) give results for hole No.① and 8 at thread position No.① and ② respectively. As it can be observed in Figure 3.6(a), the tooth profile of the TiN coated is far superior to the uncoated tap.3.3 Comparison of Work HardeningA comparative study was performed to investigate the magnitude of work hardening when using the TiN coated and uncoated taps to form threads.Results of this study are summarized in Figure 3.7. Tap No.1 of both tap types were used.Results for the TiN coated and uncoated tap are given in Figure 3.7(a) and (b) respectively. Hardness was measured on a hardness tester loaded with a 100 gw.The results show that the hardness of the TiN coated tapping thread is lower than the uncoated tapping thread. The above results show that the TiN coated tap is superior to the uncoated tap in the following aspects, thread form and work hardening etc,.3.4Comparison of Tool LifeThe TiN coated and uncoated taps were used to investigate the performance level with respect to tool life of taps. Tests were repeatedly performed three times with each type of tap. The results are summarized in Figure 3.8.Thread gauge readings were evaluated using A, B values. The results indicate that the average number of thread holes before tool life limit is reached are uncoated X =13 and TiN coated tap X =49 hole tap. The tool life of the TiN coated tap is 3.8 times longer than that of uncoated tap.3.5 Comparison of Tap WearFigure 3.9 shows the tool wear of the various taps after threading in the experiments indicated in Figure 3.8. It should be noted that all the taps used for this comparison have already attained full tool life. TiN coated and uncoated taps are shown in Figure 3.9(a) and (b), respectively. It can be seen that the point of all the taps show tool wear. In addition, extensive wear can be observed at the boundary between the full thread form with the chamfer thread run-out of same 3～5 threads from the scrape point. A comparison of the TiN coated and the uncoated tap, as exemplified by the magnified point, shows that wear of the latter is more pronounced than the former. In the case of the TiN coated tap, an overlay of TiN coating can be observed at the tool wear zone.4. Conclusions4.1The tool life of the TiN coated tap was approximately 4 times longer than that of the uncoated tap.4.2The TiN coated tap (for the 1st hole) exhibits 28% reduction in torque compared to the uncoated tap.4.3The tooth profile of the thread produced by the TiN coated tap shows fewer irregularities than for the uncoated tap.4.4 The hardness of the TiN coated tapping thread is lower than the uncoated tapping thread. 4.5From the above results, the TiN coated tap is superior to the uncoated tap in the following aspects, tool life, thread forms and work hardening etc,.References[1] WOLFGANGSTRACHE : Alternative Strategies for the Production of Threads in Aluminum-based SIC Reinforced MetalMatrix Composite (MMC) Alloy,1993.[2] Beitz.W : Dubbel-Taschhenbuch fuer den Maschinenbau. ISBN 3-540-52381-2, (1990), G15.。