Tibo Audio PA500 产品说明书

TIBO AUDIO PA500
Owner’s manual
Please read this manual carefully before using
this product and then retain for future reference.
CONTENTS
CONTENTS3
WHAT’S IN THE BOX4
SAFETY
Safety precautions 5 Important safety instructions6
CONNECTIONS 8 TECHNICAL DATA9
OTHER TIBO AUDIO PRODUCTS10 TROUBLE SHOOTING11
Owner’s manual
1 x 5 m
1 x 1 x 1 x 1 x
WHAT’S IN THE BOX
A triangle with a lighting symbol draws the user’s
attention to “dangerous voltage” without insulation in
the cabinet which may be high enough to entail a risk
of an electric shock.
A triangle with an exclamation mark draws the user’s
attention to important instructions for use and main-
tenance in the accompanying manual, which should
be studied and adhered to.
The symbol for a CLASS II (double insulation) product. Safety precautions
Warning: Caution:To minimise the risk of fire or electric shock, do not expose the unit
to rain or moisture. Do not open the cabinet as it contains dangerous voltages. Only qualified technicians are allowed to carry out repair and service of this system.
If the plug of the power cord needs to be replaced. It is important that the replacement is identical to the plug that needs to be replaced, or that the new plug has been recommended by the manufacturer.
To avoid electric shock, it is important to insert the plug correctly into the wall outlet.
SAFETY
Warning:It is important that you read and observe both the instructions in this manual and the instruction on the unit. Keep this manual for safe future reference. This unit was designed and manufactured with a view to providing maximum safety for the user. Incorrect use of the unit may cause an electric shock or fire. The protection devices built into this unit will protect the user if the procedures below are observed in connection with installation, use and repair. This unit is fully electronic and contains no parts that can be repaired by the user.Do not remove the covers. Risk of dangerous voltage. Only qualified technicians are allowed to repair the unit.
Important safety instructions
Read the manual
After unpacking the unit, please read the manual care-
fully and observe all the instructions given.
Power supply
Only the power supply indicated on the rating plate must
be used for this unit. If you are not sure which power
supply you have, please contact your local shop.
Earthing or polarisation
If the plug cannot be inserted properly into the socket,
or if the plug does not fit, the unit must not be used in
your country.
Ventilation
The cabinet is provided with slots and openings to ensure
ventilation and reliable operation and to protect the unit
against overheating. Do not block or cover these open-
ings. The openings must never be blocked, for instance
by placing the unit on a bed, a sofa, a carpet or similar
surface.
Heat
Do not place the unit near sources of heat such as radia-
tors, ovens or other units that produce heat.
Water and moisture The unit must not be placed close to water, such as bath-tub, wash basin, kitchen sink or laundry tub, in a damp cellar or close to a swimming pool, etc.Cleaning Unplug the unit before cleaning. Do not use liquid deter-gents and aerosol cleaning agents. Use a dry cloth.Power cords Wiring must be organised to prevent people from stepping on the cables and to avoid pinching by objects placed on or beside them. Take special care around sockets and plug boxes and where the power cords leave the unit.Lightning Unplug the unit for additional protection during storms or when the unit is not used for prolonged periods. This will prevent damage to the unit from lightning and power surges.
SAFETY
Important safety instructions
Penetration of objects and liquid Never push any foreign objects through the openings into the unit, as they may touch dangerous voltage points or short-circuit parts and cause fire or an electric shock. Do not spill liquid onto the unit.
Accessories
Do not place the unit on unstable surfaces such as a trolley, stand, tripod, shelf or table. The unit may fall and injure children or adults or be seriously damaged. Use only trolley, stand, tripod, shelf or table that is very stable or provided with the unit. The unit must be installed in accordance with the manufacturer’s instructions and by means of installation equipment recommended by the manufacturer. If the unit is placed on a trolley, the trolley must be moved very carefully. Sudden stops, unnecessary force and uneven surfaces may cause the trolley to turn over.
Loads
Do not place heavy loads on the unit and do not step on it. The load may fall and cause serious injury to persons or damage to the unit.
Damage
Unplug the unit and contact qualified technicians in the following cases:
A) If the power cord or the plug is damaged.
B) If liquid has been spilled on the unit or objects have fallen into the unit.
C) If the unit has been exposed to rain or water.
D) If the unit does not work properly after adhering to
the instructions in the operation manual. Only the settings described in the operation manual must be made as incorrect setting may result in damage and often will make it difficult for a qualified technician to make the unit work properly again.
E) If the unit has been dropped or damaged in any other way.
F) When the operation of the unit changes drastically, the unit requires service.
Service
Do not attempt to carry out any service work by yourself. By opening or removing the cover, you will be exposed to dangerous voltage or other hazards. Any service work should be carried out by qualified technicians. Recycling
If at any time in the future you need to dispose of this product please note that waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Approval
This product complies with European Low Voltage and Electromagnetic Compatibility Directives when used and installed according to this instruction manual.
SAFETY
1. Microphone volume control
Use this control to set the volume level of the microphone (6.3 mm or balanced). 2. XLR balanced microphone input
XLR connection for a balanced microphone 3. Microphone input
6.3 mm jack connection for a microphone 4. Line-in volume control
Use this control to set the volume level of the Line-In signal.
5. RCA Line-In
RCA connection for an external audio
device (CD, radio, DVD, etc.)
6. XLR line-In
XLR connection for an external audio
device (CD, radio, DVD, etc.)
7. Volume control
Use this control to set the general volume level.
8. 6.3 mm line-out
6.3 mm jack connection for an external audio device.
9. XLR line-out
XLR connection for an external audio
device. 10. Treble control
Use this control to adjust the treble level. 11. Bass control
Use it to adjust the bass level.
12. On/Off power switch
Press to power on/off the speaker box. 13. AC power socket and fuse carrier
Use it to connect the AC power cord.
Replace the fuse only with the correct
type and rating as specified on the rear
panel.
14. USB/SD volume control
Use to set USB/SD volume level.
15. USB port
Connect a compatible USB memory device.
16. SD memory card slot
Connect a compatible SD card.
1. LCD Screen
2. Play/Pause
Press to start playing music.
Press one more time to pause current
track, to return normal mode, press
again.
3. Stop
Press to stop current track.
4. Play mode
Select a playing mode.
R1: Repeat one, RA: Repeat All,
RD: Random.
5. Backward
Press to skip to previous track.
Press and hold to go back a track during
playback.
6. Forward
Press to skip to next track.
Press and hold to go forward a track during playback.
2
3
1
6
5
4
CONNECTIONS
Type: Tweeter: Woofer: Frequency: Crossover:
Output power: Inputs:
Outputs: Dimensions: Weight:2 way full range powered speaker 34 mm titanium
305 mm
50-18.000 Hz
3.5 kHz
120 W RMS
XLR for microphone
6.3 mm jack for microphone XLR
RCA
USB, CD card
XLR
6.3 mm jack
590(H) x 35(W) x 310(D) mm
18 kg
We reserve the right to change the technical data and the design of the product without notice as a result of further development.
TECHNICAL DATA
DJ PRO 2000 specification
Mixer:
• Large LCD display with blue back light
• 2 x CD drive
• 2 x USB slot
• Mp3 playback
• iPod docking station
• 40 sec. Anti-Shock system
• Loop and re-loop function
• Jog mode: pitch, bend, scratch, search
• 2 x XLR outputs
• 2 channel mixer, fader
• Inputs: microphone (jack/XLR), headphones) Loudspeakers:
• 2 way bass reflex active loudspeakers
• 25 mm DXT soft dome tweeter
• 165 mm polypropylene woofer
• High power 2 channel stereo amplifier built-in
• Connection for active subwoofer
• Cloth covers included Microphone:
• Superb quality dynamic microphone • Delivers a crisps detailed performance • Frequency response: 50-15,000 Hz • 4 metre microphone cable included Headphones:
• Exceptional sound output
• Frequency response: 15-22,000 Hz • Very comfortable to wear
Need Help?
You can contact our technical support
Monday - Friday
8 AM to 4 PM
***********
*************************
OTHER TIBO AUDIO PRODUCTS
Symptom Likely Cause What to do
No sound Unit is not connected to active AC power.Verify that unit is connected and the circuit
is on.
Power not switched on.Switch on power and verify that power
LED is on.
No sound, the unit is connected to working AC power but won’t come on.Unit power cable is faulty or improperly
connected.
Re-seat the power cable at both ends.
Substitute a known-good power cable. Blown fuse. Check fuse and replace with same type
“spare fuse in holder”.
Unit is operating but there is no sound.Faulty cables and connections Disconnect and re-seat signal cables.
Replace suspected cable with a known-
good cable.
Check that your USB or SD device is properly
connected and has music content.
Signal sounds distorted and very loud.Excessive input signal, trying to exceed the
capabilities of the speakers.
Excessive BASS or TREBLE boost.Reduce the output level of the source. Turn down the level controls on the speaker. Reduce BASS or TREBLE control.
Signal sound distorted even at moderate volumes.Mixer or the source is overdriven.Review the owner’s manual for your mixer
or other source and adjust controls as
needed.
Input sensitivity (gain).
Channel faders.
Lots of hiss in the sound, the mixer controls are at very low settings.Improper gain structure Make sure that the MIC/LINE switch is in the
LINE (disengaged) position.
Reduce the level settings at speaker. Review
the owner’s manual for your mixer or other
source and adjust controls as needed.
Input sensitivity (gain).
Channel faders.
Master faders.
Noise or hiss heard at output.Noisy source device.Disconnect the devices that are connected
to your unit one at a time. If the noise goes
away, the problem is with the source or the
connecting cable.
Hum or Buzz that increases or decreases when the mixer level controls are moved.
Improper A/C ground or faulty equipment
connected to mixer input.
Disconnect inputs one at a time to isolate
the problem. Refer to the owner’s manual
of the faulty equipment for troubleshoot-
ing help.
Faulty cable between source equipment
and unit.
Substitute a known-good cable for the
suspected faulty cable. TROUBLE SHOOTING
11。