Aurora 错误代码+光强模块-中英文(1)

AURORA U/T系列错误代码
1.1.1.1内存自检
RAM self-check
[0x0011,0x0011] <设备内存自检失败，错误原因0x%03X。

>
[0x0011,0x0011] <Error:0x%03X. Memory self-check failure.>
[0x0012,0x0012] <设备内存自检失败，错误原因0x%03X。

>
[0x0012,0x0012] <Error:0x%03X. Memory self-check failure.>
[0x0013,0x0013] <设备内存自检失败，错误原因0x%03X。

>
[0x0013,0x0013] <Error:0x%03X. Memory self-check failure.>
[0x0014,0x0014] <设备内存自检失败，错误原因0x%03X。

>
[0x0014,0x0014] <Error:0x%03X. Memory self-check failure.>
[0x0015,0x0015] <设备内存自检失败，错误原因0x%03X。

>
[0x0015,0x0015] <Error:0x%03X. Memory self-check failure.>
[0x0018,0x0018] <设备内存自检失败，错误原因0x%03X。

>
[0x0018,0x0018] <Error:0x%03X. Memory self-check failure.>
[0x0019,0x0019] <设备内存自检失败，错误原因0x%03X。

>
[0x0019,0x0019] <Error:0x%03X. Memory self-check failure.>
[0x001A,0x001A] <设备内存自检失败，错误原因0x%03X。

>
[0x001A,0x001A] <Error:0x%03X. Memory self-check failure.>
[0x001B,0x001B] <设备内存自检失败，错误原因0x%03X。

>
[0x001B,0x001B] <Error:0x%03X. Memory self-check failure.>
1.1.2设备阀自检
Valve self-check
[0x1003,0x1003] <设备版道上检测到有版！请关闭设备,取走版后重新打开设备。

>
[0x1003,0x1003] <Printing plate is still on the plate gate! Please shut down and take it away, then retry.> [0x1017,0x1017] <请检查设备版尾夹的安装情况！>
[0x1017,0x1017] <Please confirm whether the TEC is correctly installed or not!>
[0x1018,0x1018] <请确认设备转鼓上是否有版。

如果有版，请同步转鼓后，执行自动退版操作后取走版。

等待版门关闭后重新自检。

如果没有版，请检查设备版尾夹的安装。

>
[0x1018,0x1018] <Please confirm if there is plate on the drum. If yes, please synchronize the drum and take plate way after executing auto-plate-unload. And do self-checking after the plate door closed. If no, please confirm whether the TEC is correctly installed or not.>
[0x1021-0x1021] <执行重新自检之前，转鼓压辊不处于升起状态！>
[0x1021-0x1021] <Before self-check again, drum RO (plate roller) is not in the up state! >
[0x1022-0x1022] <执行重新自检之前，版头夹压杆不处于升起状态！>
[0x1022- 0x1022] <Before self-check again, HC press bar is not in the up state!>
[0x1023-0x1023] <执行重新自检之前，版尾夹压杆不处于升起状态！>
[0x1023- 0x1023] <Before self-check again, TEC press bar is not in the up state!>
[0x1024-0x1024] <执行重新自检之前，版尾夹横拉杆不处于锁定状态！>
[0x1024- 0x1024] <Before self-check again, TEC sliding rod is not in the SL-Lock state!>
[0x1025-0x1025] <执行重新自检之前，动平衡插杆不处于拔出状态！>
[0x1025- 0x1025] <Before self-check again, dynamic balance inserted piston is not in the out state! > [0x1026-0x1026] <执行重新自检之前，版门不处于关闭状态！>
[0x1026- 0x1026] < Before self-check again, PD is not in the close state!>
[0x1027-0x1027] <执行重新自检之前，版道不处于升起状态！>
[0x1027- 0x1027] < Before self-check again, PT is not in the up state!>
[0x1031,0x1031]<转鼓压辊对应的传感器显示不在常态（上位左和右传感器不处于升起状态，下位左和右传感器不处于压下状态）。

>
[0x1031, 0x1031] <Sensor corresponded with drum RO (plate roller)is not in the normal state (up left and right sensor is not in the up state, down left and right sensor is not in the down state).>
[0x1032,0x1032] <版头夹压杆对应的传感器显示不在常态（上位左和右传感器不处于升起状态，下位左和右传感器不处于压下状态）。

>
[0x1032, 0x1032] < Sensor corresponded with HC press bar is not in the normal state (up left and right sensor is not in the up state, down left and right sensor is not in the down state).>
[0x1033,0x1033] <版尾夹压杆对应的传感器显示不在常态（上位左和右传感器不处于升起状态，下位左和右传感器不处于压下状态）。

>
[0x1033, 0x1033] < Sensor corresponded with TEC press bar is not in the normal state (up left and right sensor is not in the up state, down left and right sensor is not in the down state).>
[0x1034,0x1034] <版尾夹横拉杆对应的传感器显示不在常态（上位传感器不处于解锁状态，下位传感器不处于锁定状态）。

>
[0x1034, 0x1034] < Sensor corresponded with TEC sliding rod is not in the normal state (up sensor is not in the SL-Relase state, down sensor is not in the SL-Lock state).>
[0x1035,0x1035] <动平衡插杆对应的传感器显示不在常态（上位传感器不处于拔出状态，下位传感器不处于插入状态）。

>
[0x1035,0x1035] < Sensor corresponded with dynamic balance inserted piston is not in the normal state (up sensor is not in the out state, down sensor is not in the in state).>
[0x1036,0x1036] <版门控制阀对应的传感器显示不在常态。

>
[0x1036,0x1036] < Sensor corresponded with plate door control valve is not in the normal state. >
[0x1037,0x1037] <版道对应的传感器显示不在常态（上位传感器不处于升起状态，下位传感器不处于放下状态）。

>
[0x1037,0x1037] < Sensor corresponded with PT (plate gate) is not in the normal state (up sensor is not in the up state, down sensor is not in the down state).>
[0x1080,0x1080] <设备急停开关被按下！请复位急停开关后重新自检。

>
[0x1080,0x1080] <Emergency stop button has been pressed down! Please reset it and redo self-check.> [0x10F0, 0x10F0] <压辊对应的传感器状态不合法>
[0x10F0, 0x10F0] <Illegal state of the sensor corresponded with plate roller>
[0x10F1, 0x10F1] <版头夹压杆对应的传感器状态不合法>
[0x10F1, 0x10F1] <Illegal state of the sensor corresponded with HC press bar>
[0x10F2, 0x10F2] <版尾夹压杆对应的传感器状态不合法>
[0x10F2, 0x10F2] <Illegal state of the sensor corresponded with TEC press bar>
[0x10F3, 0x10F3] <版尾夹横拉杆对应的传感器状态不合法>
[0x10F3, 0x10F3] <Illegal state of the sensor corresponded with TEC sliding rod>
[0x10F4, 0x10F4] <左平衡块顶杆对应的传感器状态不合法>
[0x10F4, 0x10F4] <Illegal state of the sensor corresponded with left balance block locking pin>
[0x10F5, 0x10F5] <右平衡块顶杆对应的传感器状态不合法>
[0x10F5, 0x10F5] <Illegal state of the sensor corresponded with right balance block locking pin>
[0x10FD, 0x10FD] <版道对应的传感器状态不合法>
[0x10FD, 0x10FD] <Illegal state of the sensor corresponded with plate gate>
[0x1400,0x1400] <设备阀控制器24V电源故障！>
[0x1400,0x1400] <Valve control 24V power error! >
[0x1401,0x1401] <气源压力不足！请检查设备供气压力，排除故障后重新自检。

>
[0x1401,0x1401] <Insufficient air supply presure! Please check the air pressure, troubleshoot and redo self-check again. >
1.1.3快扫自检
Fast scan self-check
[0x2002,0x2002] <设备部分气阀不处在开机默认状态！请复位气阀状态后重新自检。

>
[0x2002,0x2002] <Some valve is not on the default state! Please reset and then redo self-check.>
[0x2004,0x2004] <转鼓无法完成同步！>
[0x2004,0x2004] <Drum cannot synchronize!>
[0x2005,0x2005] <光学平台无法找到零位！>
[0x2005,0x2005] <Optical carriage cannot find the home position!>
[0x2009,0x2009] <设备运动系统自检失败，错误原因0x%03X。

>
[0x2009,0x2009] <Error:0x%03X.Motion system self-check failure. >
[0x200A,0x200A] <上下版复位失败！>
[0x200A,0x200A] <Plate loading and unloading reset failure!>
[0x20FF,0x20FF] <设备运动系统电源处于关闭状态！>
[0x20FF,0x20FF] <Motion system is power-off!>
[0x2100,0x21FF] <启动转鼓运动失败，错误原因0x%03X。

>
[0x2100,0x21FF] <Error:0x%03X. Drum starting failure. >
[0x2200,0x22FF] <启动光学平台运动失败，错误原因0x%03X。

>
[0x2200,0x22FF] <Error:0x%03X. Optical carriage starting failure.>
[0x2300,0x2300] <设备无法找到平衡块！请检查平衡块的位置，复位平衡块位置后重新自检。

> [0x2300,0x2300] <Cannot find the balanced block! Please check and reset the balanced block position, then redo self-check.>
[0x2400,0x2400] <转鼓驱动器没有准备好！>
[0x2400,0x2400] <Drum driver is not ready! >
[0x2401,0x2401] <转鼓驱动器报错！请读取转鼓驱动器屏幕提示信息，协助工程师排除设备故障。

> [0x2401,0x2401] <Drum driver error! Please read the prompted message, assisting engineers to troubleshoot. >
[0x2402,0x2402] <转鼓编码器报错！>
[0x2402,0x2402] <Drum encoder error! >
[0x2403,0x2403] <转鼓驱动器没有到位！>
[0x2403,0x2403] <Drum driver is not on the position! >
[0x2404,0x2404] <转鼓无法定位到15000EP的位置上！>
[0x2404,0x2404] <Drum cannot be lock at the position of 15000EP. >
[0x2405,0x2405] <转鼓无法从15000EP的位置按退版方向移动到10000EP的位置上！>
[0x2405,0x2405] <Drum cannot move from 15000EP to 10000EP on the plate-unload direction! >
[0x2406,0x2406] <转鼓无法从10000EP的位置按上版方向移动到5000EP的位置上！>
[0x2406,0x2406] <Drum cannot move from 15000EP to 10000EP on the plate-load direction! >
[0x2407,0x2407] <无法定位到版头夹压下位置！>
[0x2407,0x2407] <Can not locate the HC press down position!>
1.1.4 RS485自检
RS485 self-check
[0x3001,0x3001] <设备无法和调焦板通讯！>
[0x3001,0x3001] <Device cannot connect the spider board!>
[0x3010,0x301F] <设备找到的激光控制板数量和设备参数定义的光路数不匹配！错误原因0x%03X。

>
[0x3010,0x301F] <Error:0x%03X.The number of the laser control boards do not match with the laser channels defined by device parameter!>
[0x300A, 0x300A]<Tiffdownload已设置为脱机状态，但A T800已联机>
[0x300A, 0x300A] <Tiffdownloadhas been set to off-line state, but A T800 has been on-line>
[0x300B, 0x300B]<Tiffdownload已设置为联机状态，但A T800已脱机>
[0x300B, 0x300B] <Tiffdownloadhas been set to on-line state, but A T800 has been off-line>
1.1.5调焦板自检
Spider board self-check
[0x4001,0x4001] <设备找不到内核版本匹配的调焦板！>
[0x4001,0x4001] <Cannot find the spider board that match with the kernel! >
[0x4002,0x4002] <设备调焦板自检失败，错误原因0x%03X。

>
[0x4002,0x4002] <Error:0x%03X. Spider board self-check failure.>
[0x4003,0x4003] <设备调焦板序列号不合法！>
[0x4003,0x4003] <Illegal number of spider board! >
[0x4100,0x41FF] <设备调焦板初始化通讯故障，错误原因0x%03X。

>
[0x4100,0x41FF] <Error:0x%03X. Initialize communication error of spider board. >
1.1.6 HotSpot板自检
Hotspot board self-check
[0x5010,0x501F] <设备激光控制板自检失败，错误原因0x%03X。

>
[0x5010,0x501F] <Error:0x%03X. Laser control board self-check failure.>
[0x5020,0x502F] <设备激光控制板自检失败，错误原因0x%03X。

>
[0x5020,0x502F] <Error:0x%03X. Laser control board self-check failure.>
[0x5040,0x504F] <设备部分激光控制板不处于出厂状态，错误原因0x%03X。

>
[0x5040,0x504F] <Error:0x%03X. Some laser control boards are not on factory's settings.> [0x5050,0x505F] <设备部分激光控制板不处于空闲状态，错误原因0x%03X。

>
[0x5050,0x505F] <Error:0x%03X. Some laser control boards are busy.>
[0x5400,0x540F] <设备部分激光控制板初始化没有完成，错误原因0x%03X。

>
[0x5400,0x540F] <Error:0x%03X. Some laser control boards are not initialized.>
[0x5410,0x541F] <设备部分激光控制板存在故障，错误原因0x%03X。

>
[0x5410,0x541F] <Error:0x%03X. Some laser control boards error. >
1.1.7数据通路自检
Data channel self-check
[0x6001,0x6001] <设备数据通路自检失败，错误原因0x%03X。

>
[0x6001,0x6001] <Error:0x%03X. Data channel self-check failure.>
[0x6003,0x6003] <设备数据通路检查启动失败！>
[0x6003,0x6003] <Data-channel-checking starting failure! >
[0x6004,0x6004] <设备数据通路检查通讯失败！>
[0x6004,0x6004] <Data-channel-checking communication failure! >
[0x6005,0x6005] <设备数据通路检查测试数据不匹配！>
[0x6005,0x6005] <The test data does not match during data-channel-checking!>
1.1.8阀控制模块错误代码0x3000-0x3017
Valve control module error code 0x3000-0x3017
[0x3000,0x3000] <阀ID号错误，研发级错误>
[0x3000,0x3000] < Errorof the valve ID NO., development level error>
[0x3001,0x3001] <FPGA版本不对！管理级错误>
[0x3001,0x3001] < FPGA version is wrong! Management level error>
[0x3002,0x3002] <设备切换阀或继电器状态失败！>
[0x3002,0x3002] <Error:0x3002. Switching valve or relay error! >
[0x3010,0x3010] <设备参数未初始化>
[0x3010,0x3010] <Parameter is not initialized>
[0x3011,0x3011] <阀24V电源故障>
[0x3011,0x3011] <Valve 24V power supply error>
[0x3012,0x3012] <设备正在自检>
[0x3012,0x3012] <Device is doing self-check>
[0x3013,0x3013] <设备气压低于设定值>
[0x3013,0x3013] <Air pressure is lower than set value>
[0x3014,0x3014] <转鼓正在运动>
[0x3014,0x3014] <Drum is rotating>
[0x3015,0x3015] <版尾夹横拉杆正在切换，版尾夹压杆无法执行切换动作>
[0x3015,0x3015] < TEC sliding rod is switching, while TEC press bar cannot perform it! > [0x3016,0x3016] <转鼓没有完成同步，版尾夹压杆无法执行>
[0x3016,0x3016] <If drum hasn’t completed the synchronization, TEC press bar cannot perform the action!>
[0x3017,0x3017] <正在把版尾夹位置写入存储芯片，不允许升起版尾夹>
[0x3017,0x3017] <Not allow to rise up TEC when writing TEC position into storage chip>
1.1.9快扫AC马达控制模块错误代码0xE000-0xE0FF
Fast scan AC motor control module error code 0xE000-0xE0FF [0xE000,0xE000] <设备转鼓位置没有同步！>
[0xE000,0xE000] <The location of drum has not been synchornized!>
[0xE001,0xE001] <检查FPGA版本号。

保护措施>
[0xE001,0xE001] < Check FPGA version number. Protection measures >
[0xE002,0xE002] <AC电机正在运动！>
[0xE002,0xE002] <AC motor is running now!>
[0xE003,0xE003] <设备转鼓驱动器提示故障！>
[0xE003,0xE003] <Drum driver shows error! >
[0xE004,0xE004] <设备转鼓驱动器没准备好！>
[0xE004,0xE004] <Drum driver is not ready! >
[0xE005,0xE005] <设备转鼓驱动器控制信号禁止输出！>
[0xE005,0xE005] <The control signal of drum driver is not allowed to output! >
[0xE006,0xE006] <设备部分阀状态处于禁止转动状态！>
[0xE006,0xE006] <Some valves are disabled to run! >
[0xE007,0xE007] <设备传感器指示部分阀位置处于禁止转动状态！>
[0xE007,0xE007] <Sensor shows some valves are disabled to run! >
[0xE008,0xE008] <设备负压泵没有开启足够长的时间！>
[0xE008,0xE008] <Negative pressure pump doesn’t run long enough! >
[0xE009,0xE009] <转鼓速度参数不符合设备系统参数约定！>
[0xE009,0xE009] <The drum speed parameters do not meet the system parameter constraint! >
[0xE00A,0xE00A] <转鼓位置或者距离参数不符合设备系统参数约定！>
[0xE00A,0xE00A] <The drum location or distance parameters do not meet the system parameter constraint! >
[0xE00B,0xE00B] <转鼓加速度参数不符合设备系统参数约定！>
[0xE00B,0xE00B] <The drum acceleration parameters do not meet the system parameter constraint! > [0xE00D,0xE00D] <转鼓编码器显示没有到位>
[0xE00D,0xE00D] <Drum encoder shows not on the position>
[0xE00E,0xE00E] <转鼓编码器显示处于错误状态！>
[0xE00E,0xE00E] <The drum encoder shows error! >
[0xE00F,0xE00F] <转鼓方向参数不符合设备系统参数约定！>
[0xE00F,0xE00F] <The drum parameters on moving direction do not meet the system parameter constraint!>
[0xE0FF,0xE0FF] <设备运动部件控制电源被关闭！>
[0xE0FF,0xE0FF] <The moving parts control power is shutdown! >
1.1.10慢扫马达控制模块错误代码0xE400-0xE4FF
Slow scan AC motor control module error code 0xE400-0xE4FF [0xE400,0xE400] <设备光学平台位置没初始化！>
[0xE400,0xE400] <Optical carriage location is not initialized! >
[0xE401,0xE401] <设备启动光学平台运动失败！>
[0xE401,0xE401] <Start optical carriage failure!\n Error code:0xE401. >
[0xE402,0xE402] <设备光学平台正在移动！>
[0xE402,0xE402] <The optical carriage is moving now! >
[0xE403,0xE403] <光学平台马达驱动器错误！>
[0xE403,0xE403] <Optical carriage motor driver is error!>
[0xE404,0xE404] <光学平台马达驱动器没有准备好！>
[0xE404,0xE404] < Optical carriage motor driver is not ready!>
[0xE405,0xE405] <设备光学平台控制信号禁止使用！>
[0xE405,0xE405] <The optical carriage control signal is disabled to use! >
[0xE408,0xE408] <光学平台加速度参数不符合设备系统参数约定！>
[0xE408,0xE408] <The acceleration parameters of optical carriage do not meet the system parameter constraint! >
[0xE409,0xE409] <光学平台速度参数不符合设备系统参数约定！>
[0xE409,0xE409] <The speed parameters of optical carriage do not meet the system parameters constraint! >
[0xE40A,0xE40A] <光学平台距离参数超过设备允许移动范围！>
[0xE40A,0xE40A] <The distance parameters of optical carriage exceed the maximum value! >
[0xE40B,0xE40B] <转鼓与光学平台联动参数超过最大允许值！>
[0xE40B,0xE40B] <The drum and optical carriage linkage parameters exceed the maximum limit! > [0xE40C,0xE40C] <光学平台位置或距离参数超过设备系统参数最大限制！>
[0xE40C,0xE40C] <The location or distance parameters of optical carriage exceed the maximum value! > [0xE40D,0xE40D] <设备光学平台驱动器没有到位！>
[0xE40D,0xE40D] < Optical carriage motor driver is not on the position!>
[0xE40E,0xE40E] <设备正在曝光，光学平台已被锁定无法执行移动动作！>
[0xE40E,0xE40E] <Device is exposing, optical carriage is locked and cannot perform the moving action!> [0xE40F,0xE40F] <光学平台方向参数不符合设备系统参数约定！>
[0xE40F,0xE40F] <The parameters of optical carriage on moving direction do not meet the system parameter constraint! >
[0xE4FF,0xE4FF] <设备运动部件控制电源被关闭！>
[0xE4FF,0xE4FF] <The motion parts control power is shutdown! >
1.1.11光学平台归零模块错误代码0xE500-0xE5FF
Optical carriage searching home position module error code0xE500-0xE5FF [0xE500,0xE500] <设备系统参数没有完成初始化！>
[0xE500,0xE500] <The system parameters are not initialized! >
[0xE501,0xE501] <设备光学平台正在移动！>
[0xE501,0xE501] <The optical carriage is moving now! >
[0xE502,0xE502] <设备光学平台正在寻找零位！>
[0xE502,0xE502] <The optical carriage is searching the home position now! >
[0xE504,0xE504] <设备当前有其它任务正在执行！>
[0xE504,0xE504] <Some other tasks are running now!>
[0xE5FF,0xE5FF] <设备运动部件控制电源被关闭！>
[0xE5FF,0xE5FF] <The moving parts control power is shutdown! >
1.1.12上下版控制模块错误代码0x7701-0x77C0
Loading \ unloading plate control module error code 0x7701-0x77C0 [0x7701,0x7701] <上下版过程中阀状态不合法！>
[0x7701,0x7701] < State of valve is illegal when loading / unloading plate!>
[0X7703,0X7703] <进行快扫描时检测到转鼓在转动！>
[0X7703,0X7703] <Drum is rotating when fast scanning!>
[0x7704,0x7704] <快扫描过程中，AC电机出错！>
[0x7704,0x7704] < AC motor is in error when fast scanning!>
[0x7705,0x7705] <快扫描时转鼓位置未进行初始化！>
[0x7705,0x7705] <Drum position is not initialized when fast scanning!>
[0x7706,0x7706] <上下版过程中版头夹压下位置不到位！>
[0x7706,0x7706] <HC press down position is not in the right place when plate loading and unloading!> [0x7707,0x7707] <上下版过程中版尾夹压下位置不到位！>
[0x7707,0x7707] < TEC press down position is not in the right place when plate loading and unloading!> [0x7708,0x7708] <版道升起位置不到位！>
[0x7708,0x7708] <Plate gate raising position is not in the right place! >
[0x7709,0x7709] <版宽不符合规定！>
[0x7709,0x7709] <Plate width does not meet the constraint!>
[0x770A,0x770A] <急停开关被拍下！>
[0x770A,0x770A] <Emergency stop button has been pressed down!>
[0x770B,0x770B] <正在进行上下版！>
[0x770B,0x770B] <Plate is being loaded or unloaded!>
[0x770E,0x770E] <驱动与设备不匹配，请保存你的设备信息INI文件，并与amsky联系！>
[0x770E,0x770E] < The driver does not match with device, please save your information INI file and contact with amsky!>
[0x770F,0x770F] <内核与诊断程序之间的错误，请与amsky联系！>
[0x770F,0x770F] < The error is between kernel and diagnosis program, please contact with amsky!> [0x7741,0x7741] <上版道传感器状态不合法>
[0x7741,0x7741] < State of the up plate gate sensor is illegal>
[0x77F0, 0x77F0] <上下版过程中，压辊对应的传感器状态不合法>
[0x77F0, 0x77F0] <State of the sensor corresponded with plate roller is illegal when loading / unloading plate>
[0x77F1, 0x77F1] <上下版过程中，版头夹压杆对应的传感器状态不合法>
[0x77F1, 0x77F1] < State of the sensor corresponded with HC press bar is illegal when loading / unloading plate >
[0x77F2, 0x77F2] <上下版过程中，版尾夹压杆对应的传感器状态不合法>
[0x77F2, 0x77F2] < State of the sensor corresponded with TEC press bar is illegal when loading / unloading plate >
[0x77F3, 0x77F3] <上下版过程中，版尾夹横拉杆对应的传感器状态不合法>
[0x77F3, 0x77F3] < State of the sensor corresponded with TEC sliding rod is illegal when loading / unloading plate >
[0x77F4, 0x77F4] <上下版过程中，左平衡块顶杆对应的传感器状态不合法>
[0x77F4, 0x77F4] < State of the sensor corresponded with left balance block locking pin is illegal when loading / unloading plate >
[0x77F4, 0x77F4] <上下版过程中，左平衡块顶杆对应的传感器状态不合法>
[0x77F4, 0x77F4] < State of the sensor corresponded with left balance block locking pin is illegal when loading / unloading plate >
[0x77F5, 0x77F5] <上下版过程中，右平衡块顶杆对应的传感器状态不合法>
[0x77F5, 0x77F5] < State of the sensor corresponded with right balance block locking pin is illegal when loading / unloading plate >
[0x77F5, 0x77F5] <上下版过程中，右平衡块顶杆对应的传感器状态不合法>
[0x77F5, 0x77F5] < State of the sensor corresponded with right balance block locking pin is illegal when loading / unloading plate >
[0x77FD, 0x77FD] <上下版过程中，版道对应的传感器状态不合法>
[0x77FD, 0x77FD] < State of the sensor corresponded with plate gate is illegal when loading / unloading plate >
[0x77FD, 0x77FD] <上下版过程中，版道对应的传感器状态不合法>
[0x77FD, 0x77FD] < State of the sensor corresponded with plate gate is illegal when loading / unloading plate >
1.1.13自动进版模块错误代码
Error code of the auto-feed plate module
[0x7711,0x7711] <下版道电机运动超过最大时间限制>
[0x7711, 0x7711] <Movement time of the down plate gate motor is more than maximum limit>
[0x7724,0x7724] <打印模块取消进版>
[0x7724,0x7724] <Print module cancelsfeeding plate >
[0x7726,0x7726] <版道不处于进版位置，无法启动进版>
[0x7726,0x7726] <Can’t start feeding plate when plate gate is not on the position>
[0x7727,0x7727] <启动进版后，版道上没有版>
[0x7727,0x7727] <After starting feeding plate, there is no plate on the plate gate>
[0x7728,0x7728] <启动进版后，上版道模块出现错误，但是没有显示任何错误>
[0x7728,0x7728] < After starting feeding plate, up plate gate is in error but shows no errors>
[0x7729,0x7729] <上版道模块不处在允许进版状态>
[0x7729,0x7729] <Up plate gate module is not in the feeding plate state >
[0x772A,0x772A] <Autoload启动送版(OutMedia)指令后，超过指定时间上版道始终没有接收到版> [0x772A,0x772A] <After Autoload startingOutMedia instruction, up plate gate does not receive plate beyond the appointed time >
[0x772B,0x772B] <CTP进版动作执行时间超过指定的时间>
[0x772B,0x772B] < Execution time of CTP feeding plate is more than the specified time>
[0x772C,0x772C] <Autoload操作(清错,取板)时间超过指定的时间>
[0x772C,0x772C] <Autoload operation (clear error, take plate away) time is more than the specified time> [0x772D,0x772D] <Autoload出于错误状态或者非正常状态>
[0x772D,0x772D] <Autoload is in error condition or abnormal condition>
[0x772E,0x772E] <Autoload状态查询模块出现错误>
[0x772E,0x772E] <Autoload status query module is in error>
[0x772F,0x772F] <启动进版前，上版道模块出现错误，但是没有显示任何错误>
[0x772F,0x772F] < Before starting feeding plate, up plate gate is in error but shows no errors>
1.1.14平衡块控制模块错误代码0xBB00-0xBB13
Balance block control module error code 0xBB00-0xBB13
[0xBB00,0xBB00] <设备气阀不处于平衡块操作允许的状态！>
[0xBB00,0xBB00] <Valves are not in the proper condition, balanced block are not allowed to operate! > [0xBB02,0xBB02] <设备在没有找到任意平衡块！>
[0xBB02,0xBB02] <Balanced block missing!>
[0xBB03,0xBB03] <设备找到的平衡块无法限定在两组操作位置！>
[0xBB03,0xBB03] <Cannot set the balanced blocks within their operating range!>
[0xBB04,0xBB04] <平衡块查找初始化失败！>
[0xBB04,0xBB04] <Balance block searching initialization failure>
[0xBB0A,0xBB0A] <平衡块查找动作被意外停止！>
[0xBB0A,0xBB0A] <The homing process of balanced block has been inexpertly stopped! >
[0xBB0B,0xBB0B] <设备气阀位置传感器指示气阀动作不到位！>
[0xBB0B,0xBB0B] <The valve position’ sensor shows that the valve's motion is not in place! >
[0xBB0C,0xBB0C] <在设备保存的平衡块位置上没有找到平衡块！请重新查找平衡块后重新定位平衡块。

>
[0xBB0C,0xBB0C] <Cannot find the balanced blocks at the saved positions! Please check and relocate the balanced blocks.>
[0xBB0D,0xBB0D] <检测到急停开关被按下！>
[0xBB0D,0xBB0D] <Emergency stop button has been pressed! >
[0xBB0E,0xBB0E] <运动控制系统电源被关闭！>
[0xBB0E,0xBB0E] <The power of motion system has been shutdown! >
[0xBB0F,0xBB0F] <平衡块控制器不明原因故障！请联系软件供应商。

>
[0xBB0F,0xBB0F] <The balanced blocks controller error with an unknown reason! Please connect with the software suppliers.>
[0xBB10,0xBB13] <转鼓移动不到指定位置>
[0xBB10,0xBB13] <Drum cannot be moved to set position>
1.1.15版边检测控制模块错误代码0xE600-0xE689
Plate edge detection control module error code 0xE600-0xE689 [0xE600,0xE600] <用户取消版边检测操作！>
[0xE600,0xE600] <User has cancelled the edge detection operation! >
[0xE602,0xE602] <参数未初始化！！>
[0xE602,0xE602] <Parameter is not initialized!!>
[0xE610,0xE610] <设备正在寻零！>
[0xE610,0xE610] <Device is searching the home position now!>
[0xE611,0xE611] <光学平台无法找到设备零位！>
[0xE611,0xE611] <The optical carriage cannot find the home position! >
[0xE612,0xE612] <光学平台无法停止在设备零位！>
[0xE612,0xE612] <The optical carriage cannot stop at the home position! >
[0xE615,0xE615] <光学平台无法停止在检测起始位置！>
[0xE615,0xE615] <The optical carriage cannot stop at the start-to-detect position! >
[0xE617,0xE617] <光学平台无法停止在检测结束位置！>
[0xE617,0xE617] <The optical carriage cannot stop at the stop-to-detect position! >
[0xE620,0xE620] <部分气阀不处于转鼓允许运动状态！>
[0xE620,0xE620] <Some valve is in wrong position, drum rotation is prohibited! >
[0xE621,0xE627] <气阀位置检测传感器显示部分气阀不处于转鼓允许运动状态！>
[0xE621,0xE621] <The valve position’ sensor shows that some valve is in wrong position, drum rotation has been prohibited! >
[0xE640,0xE640] <在检测起始位置没有找到版材！>
[0xE640,0xE640] <Cannot find the plate at the start-to-detect position! >
[0xE641,0xE641] <检测过程中始终显示找到版材！>
[0xE641,0xE641] <Cannot find the plate during the whole checking process! >
[0xE643,0xE643] <检测完成时光学平台停止位置不在设备工作行程范围内！>
[0xE643,0xE643] <After optical carriage test, the head position is not within the operating range. >
[0xE650,0xE650] <运动控制系统电源被关闭！>
[0xE650,0xE650] <The power of motion control system has been shutdown! >
[0xE654,0xE655] <镜头位置发生过载！>
[0xE654,0xE655] <Lens position is overloaded!>
[0xE661,0xE661] <无法设定到版边检测的焦距位置！>
[0xE661,0xE661] <Cannot set the focus position to edge detection! >
[0xE662,0xE662] <版边检测传感器反馈光强超过检测电路的允许最大值！>
[0xE662,0xE662] < The feedback laser power of edge detection sensor is more than the Max default value! >
[0xE663,0xE663] <版边检测传感器反馈光强小于控制参数允许的最小值！请检查版边检测控制参数。

>
[0xE663,0xE663] <The feedback laser power of edge detection position sensor is less than the Min default value! Please check the control parameter of edge detection. >
[0xE664,0xE664] <版边检测传感器反馈光强大于控制参数允许的最大值！请检查版边检测控制参数。

>
[0xE664,0xE664] <The feedback laser power of edge detection position sensor is more than the Max default value! Please check the control parameter of edge detection. >
[0xE665,0xE665] <版边检测传感器检测位置小于控制参数允许的最小值！请检查版边检测控制参数。

>
[0xE665,0xE665] <The detection position of edge detection position sensor is less than the Min default value! Please check the control parameter of edge detection. >
[0xE666,0xE666] <版边检测传感器检测位置大于控制参数允许的最大值！请检查版边检测控制参数。

>
[0xE666,0xE666] <The detection position of edge detection position sensor is more than the max default value! Please check the control parameter of edge detection. >
[0xE66F,0xE66F] <找不到调焦板！>
[0xE66F,0xE66F] <Spider board cannot be found!>
[0xE671,0xE677] <阀对应传感器有问题！>
[0xE671,0xE677] <Sensor corresponded with valve is error!>
[0xE680,0xE680] <正在版边检测！>
[0xE680,0xE680] <Plate edge is detecting now>
[0xE681,0xE681] <系统有其他冲突事件！>
[0xE681,0xE681] <System has other conflict!>
[0xE682,0xE682]<转鼓电机没能完成同步！>
[0xE682,0xE682] <Drum motor hasn’t completed the synchronization!>
[0xE683,0xE683] <未连接调焦板！>
[0xE683,0xE683] <Spider board hasn’t been connected!>
[0xE685,0xE685] <调焦板不处于空闲状态！>
[0xE685,0xE685] <Spider board is not in the idle state!>
[0xE686,0xE686] <调焦板未初始化！>
[0xE686,0xE686] <Spider board is not initialized!>
[0xE688,0xE688] <转鼓位置异常！>
[0xE688,0xE688] <Drum position is error!>
[0xE689,0xE689] <查找版边的起始位置，超出光学平台的最大位置限制！>
[0xE689,0xE689] < Find the starting position of the plate edge, beyond the maximum position limitation of the optical carriage!>
[0xE670,0xE670] <检测光点没有落在版边上，请将版材放置在预先设定的版边位置>
[0xE670, 0xE670] <Detection laser spot can n’t locate at the plate edge, please put the plate on the preset plate edge position >
[0xE6F0, 0xE6F0] <找版边过程中，压辊对应的传感器状态不合法>
[0xE6F0, 0xE6F0] < In the process of plate edge detection, state of the sensor corresponded with plate roller is illegal>
[0xE6F1, 0xE6F1] <找版边过程中，版头夹压杆对应的传感器状态不合法>
[0xE6F1, 0xE6F1] < In the process of plate edge detection, state of the sensor corresponded with HC press bar is illegal>
[0xE6F2, 0xE6F2] <找版边过程中，版尾夹压杆对应的传感器状态不合法>
[0xE6F2, 0xE6F2] < In the process of plate edge detection, state of the sensor corresponded with TEC press bar is illegal>
[0xE6F3, 0xE6F3] <找版边过程中，版尾夹横拉杆对应的传感器状态不合法>
[0xE6F3, 0xE6F3] < In the process of plate edge detection, state of the sensor corresponded with TEC sliding rod is illegal>
[0xE6F4, 0xE6F4] <找版边过程中，左平衡块顶杆对应的传感器状态不合法>
[0xE6F4, 0xE6F4] < In the process of plate edge detection, state of the sensor corresponded with left balance block locking pin is illegal>
[0xE6F5, 0xE6F5] <找版边过程中，右平衡块顶杆对应的传感器状态不合法>。