SUNLORDINC顺络电子共模选型
细说磁珠
说说磁珠(Ferrite Bead)第一次使用磁珠还是在实习的时候，但是看原理图发现有个元件写着”Bea d”，单位是100欧姆，用万用表测，导通，电阻约为0。
当时就很奇怪，是什么有什么用？后来问了师兄，才知道，这个是磁珠，相当于电感，通直流阻交流(不准确)。
这就是我当初对磁珠的印象。
磁珠全称为铁氧体磁珠，Ferrite Bead，简写FB。
磁珠的单位是欧姆，而不是亨特，这一点要特别注意。
因为磁珠的单位是按照它在某一频率产生的阻抗来标称的，阻抗的单位也是欧姆。
磁珠的 DATASH EET上一般会提供频率和阻抗的特性曲线图，一般以100MHz为标准，比如60 0R@100MHz，意思就是在100MHz频率的时候磁珠的阻抗相当于600欧姆。
磁珠的结构X射线下的结构(真的活像线圈)磁珠的等效模型R bead是磁珠的直流电阻；L bead是磁珠的等效电感；Cpar和Rpar是并联电容和电阻。
在低频的时候，Cpar开路，L bead短路，只有直流电阻R bead。
当频率增加的时候，阻抗(JwL bead)随着L bead的增加线性增加，阻抗(1/jwCpar)随着Cpar的减小而相反增长。
磁珠的阻抗频率曲线图上升斜率主要由电感L bead决定。
在高频到达一定频率点时，Cpar的阻抗开始起主要作用。
磁珠的阻抗开始减小。
阻抗频率曲线的斜率下降主要由磁珠的寄生电容Cpar所决定。
Rpar对抑制品质因素(Q-factor)有作用，无论如何，Rpar和Cpar的值增长过大会增加磁珠的品质因素和减小磁珠的有效带宽。
高品质因素(Q)可能导致电源输送网络瞬态频率响应不想要的抬升。
Z=R+jxZ：阻抗R：电阻X：电抗磁珠的电性参数Z(阻抗) [Z]@100MHz (ohm)磁珠的阻抗是指在电流下所有阻抗的总和，包括交流与直流部分。
阻抗的直流部分仅仅是绕线的直流电阻，交流部分包括电感电抗。
下面的公式计算了一个理想电感在正弦交流信号下的电感电抗。
SUNLORDINC顺络电子一级代理分销经销通路供应商KOYUELEC光与电子SDMM0806U
【Version change history】Rev. Effective Date Changed Contents Change reasons Approved By01 / New release / Hai GuoCautionAll products listed in this specification are developed, designed and intended for use in general electronics equipment. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require especially high reliability, or whose failure, malfunction or trouble might directly cause damage to society, person, or property. Please understand that we are not responsible for any damage or liability caused by use of the products in any of the applications below. Please contact us for more details if you intend to use our products in the following applications.1.Aircraft equipment2.Aerospace equipment3.Undersea equipment4.nuclear control equipmentitary equipment6.Power plant equipment7.Medical equipment8.Transportation equipment (automobiles, trains, ships,etc.)9.Traffic signal equipment10.Disaster prevention / crime prevention equipment11.Data-processing equipment12. The application with a long term direct-current voltage difference, which is greater than 1.5V, between D+ and D- of differential lines13. Applications of similar complexity or with reliability requirements comparable to the applications listed in the above1. ScopeThis specification applies to SDMM Series of multi-layer common mode filter. 2.Product Description and Identification (Part Number) 1) DescriptionSDMM Series of multi-layer common mode filter. 2)Product Identification (Part Number) SDMM 0806 U -2 -□□□T ① ② ③ ④ ⑤ ⑥3. Electrical CharacteristicsPlease refer to Appendix A . 1) Operating and storage temperature range (individual chip without packing): -40 ~ +85℃℃ 2) Storage temperature range (packaging conditions): -10~+40 and RH 70% (Max.)℃℃Appendix A: Electrical CharacteristicsPart NumberCommon modeImpedance @ 100MHz(Ω)DC Resistance (Ω) Max.Rated Current (mA) Max.Insulation Resistance (M Ω) Min.Cutoff Frequency(typ.) (GHz) SDMM0806U-2-120T 12±5 2.5 130 100 ＞8 SDMM0806U-2-350T 35±20% 3.5 100 100 ＞6SDMM0806U-2-470T 47±20% 4.0 100 100 6 SDMM0806U-2-900T 90±20% 4.51001003.5Note: Absolute maximum long term direct-current voltage between D+ and D- of differential lines: DC 1.5VPacking ⑥TTape Carrier Package① TypeSDMMmultilayer commonmode filter② External Dimensions (L x W) (mm)08060.85×0.65Number of Lines ④-2 2 linesCommon Mode Impedance ⑤ (Ω)Example Nominal Value350 35③Feature TypeUFor Ultra high speedDifferential SignalLinesTypical Electrical CharacteristicsSDMM0806U-2-120T SDMM0806U-2-350TImpedance vs. Frequency(SDMM0806U-2-120T) Impedance vs. Frequency(SDMM0806U-2-350T)Insertion loss vs. Frequency (SDMM0806U-2-120T) Insertion loss vs. Frequency (SDMM0806U-2-350T)Insertion loss vs. Frequency (SDMM0806U-2-120T) Insertion loss vs. Frequency (SDMM0806U-2-350T)SDMM0806U-2-470T SDMM0806U-2-900TImpedance vs. Frequency (SDMM0806U-2-470T) Impedance vs. Frequency (SDMM0806U-2-900T)Insertion loss vs. Frequency (SDMM0806U-2-470T) Insertion loss vs. Frequency (SDMM0806U-2-900T)Insertion loss vs. Frequency (SDMM0806U-2-470T) Insertion loss vs. Frequency (SDMM0806U-2-900T)4. Shape and Dimensions1) Dimensions: See Fig.4-1 and Table 4-1. 2) Equivalent circuit: See Fig. 4-2.3)Recommended PCB pattern for reflow soldering: See Fig. 4-3.4) Structure: See Fig. 4-4 and Fig. 4-5.Material Information: See Table 4-2.[Table 4-2]Code Part NameMaterial Name ① Ceramic Body Ceramic Powder ② Ferrite Body Ferrite Powder ③ Inner Coils(Ag) Silver Paste ④ Pull-out Electrode (Ag) Silver PasteTypeL W T SL SW P 0806 0.85±0.05 0.65±0.05 0.40±0.05 0.20+0.05/-0.10 0.27±0.05 0.50±0.05[Table 4-1] Unit: mmSW（3） （1） （4）（2）（3） （1） （2）（4）For 0806Fig. 4-2Fig. 4-3Fig.4-1①③④⑤Fig. 4-4②①AgStructure of Electro-platingBodyNiSn⑤-1 ⑤-2Fig. 4-55.Test and Measurement Procedures 5.1 Test ConditionsUnless otherwise specified, the standard atmospheric conditions for measurement/test as:a. Ambient Temperature: 20±15℃b. Relative Humidity: 65±20%c.Air Pressure: 86 kPa to 106 kPaIf any doubt on the results, measurements/tests should be made within the following limits:a. Ambient Temperature: 20±2℃b. Relative Humidity: 65±5%c. Air Pressure: 86kPa to 106 kPa 5.2 Visual Examination a. Inspection Equipment: 20× magnifier5.3 Electrical TestItems Requirements Test Methods and Remarks5.3.1 Impedance (Common Mode)Refer to Appendix ATest equipment: High Accuracy RF LCR Meter Agilent4287A/E4991A or equivalent.Common Mode Impedance is tested according to the following circuit.5.3.2 Impedance (Differential Mode)Refer to Appendix ATest equipment: High Accuracy RF LCR Meter Agilent4287A/E4991A or equivalent. Differential Mode Impedance is tested according to the following circuit.5.3.3DC ResistanceRefer to Appendix ATest equipment: High Accuracy Milliohm meter Agilent4338B/34420 or equivalent. DC Resistance is tested according to the following circuit.5.3.4Rated CurrentRefer to Appendix ATest equipment: Electric Power, Electric current meter, Thermometer.Definition of Rated Current (Ir): Ir is direct electric current as chip surface temperature rise just20 against chip initial surface temperature.℃ Rated Current is tested according to the following circuit.5.3.5 Insulation ResistanceRefer to Appendix ATest equipment: High resistance meter Agilent4339B. Withstand Voltage:2.5 times rated voltage Application time:1~5 SecondsThe charging and discharging current::Less than 1mAInsulation Resistance is tested according to the following circuit.5.3.6Insertion LossRefer to Appendix ATest equipment: S-parameter Network Analyzer AgilentE5071C or equivalent. Insertion Loss is S21mag tested according to the following circuit.5.4.10 Loading under damp heat① No visible mechanical damage. ② Impedance change: within ±20%. ③ Insulation Resistance: 100M Ω Min.① Temperature: 60±2.℃ ② Humidity: 90% to 95% RH. ③ Duration: 1000+12hours.④ Applied current: Rated current.⑤ The chip shall be stabilized at normal condition for 1~2 hoursbefore measuring.5.4.11Loading at high temperature (Life test) ① No visible mechanical damage. ② Impedance change: within ±20%. ③ Insulation Resistance: 100M Ω Min.① Temperature: 85±2.℃ ② Duration: 1000+12hours.③ Applied current: Rated current.④The chip shall be stabilized at normal condition for 1~2 hours before measuring.6. Packaging and Storage6.1 PackagingTape Carrier Packaging: Packaging code: T a. Tape carrier packaging are specified in attached figure Fig.6.1-1~4 b.Tape carrier packaging quantity please see the following table:Type 0806 Tape Paper Tape Quantity10Kc. Reel shall be packaged in vinyl bag.d. Maximum of 5 or 10 reels bags shall be packaged in an inner box.e.Maximum of 6 or 10 inner boxes shall be packaged in an outer case.(1)Remark: The sprocket holes are to the right as the tape is pulled toward the user.(2) Taping Dimensions (Unit: mm)Type A B P Tmax 08060.80±0.051.0±0.052.0±0.050.55Chip CavityTSunlord Business categories ：Level 0（general confidential ） Specifications for Multi-layer Common Mode Filter Page 11 of 11(3) Reel Dimensions (Unit: mm)6.2 Storage a. The solderability of the external electrode may be deteriorated if packages are stored where they are exposed to high humidity. Package must be stored at 40 or less and 70% RH or less.℃b. The solderability of the external electrode may be deteriorated if packages are stored where they are exposed to dust of harmful gas (e.g. HCl, sulfurous gas of H 2S).c. Packaging material may be deformed if package are stored where they are exposed to heat of direct sunlight.d.Solderability specified in Clause 5.4.6shall be guaranteed for 6 months from the date of delivery on condition that they are stored at the environment specified in Clause 3 .For those parts, which passed more than 6 months shall be checked solder-ability before use.7. Recommended Soldering Technologies7.1 Re-flowing Profile:△ Preheat condition: 150 ~200/60~120℃sec. △ Allowed time above 217: 60~90s ℃ec. △ Max temp: 260℃△ Max time at max temp: 10sec. △ Solder paste: Sn/3.0Ag/0.5Cu △ Allowed Reflow time: 2x max7.2 Iron Soldering Profile.△ Iron soldering power: Max.30W. △ Pre-heating: 150 / 60 sec. ℃ △ Soldering Tip temperature: 350Max.℃ △ Soldering time: 3 sec Max. △ Solder paste: Sn/3.0Ag/0.5Cu. △ Max.1 times for iron soldering. [Note: Take care not to apply the tip of the soldering iron to the terminal electrodes.]CFig.6.1.34.3±0.2mm4.0±0.1mm5.0±0.1mm3.0±0.1mmmax ＜14.4mm[Note: The reflow profile in the above table is only for qualification and is not meant to specify board assembly profiles. Actual board assembly profiles must be based on the customer's specific board design, solder paste and process, and should not exceed the parameters as the Reflow profile shows.]26015020021725℃ Tc ℃350℃。
细说磁珠
说说磁珠(Ferrite Bead)第一次使用磁珠还是在实习的时候，但是看原理图发现有个元件写着”Bea d”，单位是100欧姆，用万用表测，导通，电阻约为0。
当时就很奇怪，是什么有什么用？后来问了师兄，才知道，这个是磁珠，相当于电感，通直流阻交流(不准确)。
这就是我当初对磁珠的印象。
磁珠全称为铁氧体磁珠，Ferrite Bead，简写FB。
磁珠的单位是欧姆，而不是亨特，这一点要特别注意。
因为磁珠的单位是按照它在某一频率产生的阻抗来标称的，阻抗的单位也是欧姆。
磁珠的 DATASH EET上一般会提供频率和阻抗的特性曲线图，一般以100MHz为标准，比如60 0R@100MHz，意思就是在100MHz频率的时候磁珠的阻抗相当于600欧姆。
磁珠的结构X射线下的结构(真的活像线圈)磁珠的等效模型R bead是磁珠的直流电阻；L bead是磁珠的等效电感；Cpar和Rpar是并联电容和电阻。
在低频的时候，Cpar开路，L bead短路，只有直流电阻R bead。
当频率增加的时候，阻抗(JwL bead)随着L bead的增加线性增加，阻抗(1/jwCpar)随着Cpar的减小而相反增长。
磁珠的阻抗频率曲线图上升斜率主要由电感L bead决定。
在高频到达一定频率点时，Cpar的阻抗开始起主要作用。
磁珠的阻抗开始减小。
阻抗频率曲线的斜率下降主要由磁珠的寄生电容Cpar所决定。
Rpar对抑制品质因素(Q-factor)有作用，无论如何，Rpar和Cpar的值增长过大会增加磁珠的品质因素和减小磁珠的有效带宽。
高品质因素(Q)可能导致电源输送网络瞬态频率响应不想要的抬升。
Z=R+jxZ：阻抗R：电阻X：电抗磁珠的电性参数Z(阻抗) [Z]@100MHz (ohm)磁珠的阻抗是指在电流下所有阻抗的总和，包括交流与直流部分。
阻抗的直流部分仅仅是绕线的直流电阻，交流部分包括电感电抗。
下面的公式计算了一个理想电感在正弦交流信号下的电感电抗。
Sunlord多层片陶瓷电感SDCL-D系列说明书
Multilayer Chip Ceramic Inductor – SDCL-D SeriesOperating Temp. : SDCL1005 series: -55℃~+125℃SDCL1608 series: -40℃~+85℃FEATURES●Monolithic structure for high reliability● High self-resonant frequency● Excellent solderability and high heat resistanceAPPLICATIONS●RF circuit in telecommunication and other equipmentsPRODUCT IDENTIFICATIONSHAPE AND DIMENSIONSUnit: mm [inch]Type L W T a SDCL1005[0402]1.0±0.15 [.039±.006]0.5±0.15 [.020±.006]0.5±0.15 [.020±.006]0.25±0.1 [.010±.004]Fig.11.6±0.15 [.063±.006]SDCL1608 [0603] 1.65±0.15 [.065±.006]0.8±0.15 [.031±.006]0.8±0.15 [.031±.006] 0.3±0.2 [.012±.008]Fig.2②External Dimensions (L×W) (mm)1005 [0402] 1.0×0.5 1608 [0603] 1.6×0.8 ① Type SDCL Chip Ceramic Inductor③ Material Code C ④ Nominal Inductance Example Nominal Value 3N9 3.9nH 10N 10nH R10 100nH※R= Decimal Point ，N=nH ⑤Inductance ToleranceS ±0.3nH J ±5%K ±10% ⑥ Packing T Tape & Reel ⑧Hazardous Substance Free Products FSDCL ① 1608② C ③ 10N ④ J ⑤ T⑥ D ⑦ F ⑧ ⑦Internal Code D Fig.1Fig.2SPECIFICATIONSSDCL1005-D TYPETypical Q @ Freq. (MHz)Part Number InductanceMin. Qual i t y FactorL,Q Test Freq.L/Q 1008001000Min. Self-resonant FrequencyMax. DCResistanceMax.RatedCurrent ThicknessUnits nH - MHz - MHz Ω mA mm [inch]SymbolL Q Freq Q S.R.F DCR Ir T SDCL1005C1N0STDF 1.0±0.3 8 10011 34 36 10000 0.10 400 SDCL1005C1N1STDF 1.1±0.38 10011 34 36 10000 0.10 400 SDCL1005C1N2STDF 1.2±0.38 10011 34 36 10000 0.10 400 SDCL1005C1N3STDF 1.3±0.38 10011 34 36 10000 0.10 400 SDCL1005C1N5STDF 1.5±0.38 10011 34 36 6000 0.10 300 SDCL1005C1N6STDF 1.6±0.38 10011 32 35 6000 0.10 300 SDCL1005C1N8STDF 1.8±0.38 10011 30 34 6000 0.10 300 SDCL1005C2N0STDF 2.0±0.38 10010 29 33 6000 0.20 300 SDCL1005C2N2STDF 2.2±0.38 10010 29 33 6000 0.20 300 SDCL1005C2N4STDF 2.4±0.38 10010 29 32 6000 0.20 300 SDCL1005C2N7STDF 2.7±0.38 10010 29 32 6000 0.20 300 SDCL1005C3N0STDF 3.0±0.38 10010 29 32 6000 0.20 300 SDCL1005C3N3STDF 3.3±0.38 10010 29 32 6000 0.20 300 SDCL1005C3N6STDF 3.6±0.38 10010 28 31 4000 0.20 300 SDCL1005C3N9STDF 3.9±0.38 10010 28 31 4000 0.20 300 SDCL1005C4N3STDF 4.3±0.38 10010 28 31 4000 0.20 300 SDCL1005C4N7STDF 4.7±0.38 10010 28 31 4000 0.20 300 SDCL1005C5N1STDF 5.1±0.38 10010 28 30 4000 0.30 300 SDCL1005C5N6STDF 5.6±0.38 10010 28 30 4000 0.30 300 SDCL1005C6N2STDF 6.2±0.38 10010 27 30 3900 0.30 300 SDCL1005C6N8□TDF 6.8 8 10010 27 30 3900 0.30 300 SDCL1005C7N5□TDF 7.5 8 10010 27 30 3700 0.40 300SDCL1005C8N2□TDF 8.2 8 10010 27 30 3600 0.40 300SDCL1005C9N1□TDF 9.1 8 10010 27 30 3400 0.40 300 SDCL1005C10N □TDF 10 8 10010 27 30 3200 0.40 300 SDCL1005C12N □TDF 12 8 10010 26 29 2700 0.50 300 SDCL1005C15N □TDF 15 8 10010 26 28 2300 0.50 300 SDCL1005C18N □TDF 18 8 10010 25 27 2100 0.60 300 SDCL1005C20N □TDF 20 8 10010 25 26 2000 0.60 300 SDCL1005C22N □TDF 22 8 10010 25 25 1900 0.60 300 SDCL1005C27N □TDF 27 8 10010 25 23 1600 0.70 300 SDCL1005C33N □TDF 33 8 10010 22 22 1300 0.80 200 SDCL1005C39N □TDF 39 8 10010 22 19 1200 1.00 200 SDCL1005C43N □TDF 43 8 10010 21 16 1100 1.10 200 SDCL1005C47N □TDF 47 8 10010 21 16 1000 1.10 200 SDCL1005C56N □TDF 56 8 10010 18 13 750 1.20 200 SDCL1005C68N □TDF 68 8 10010 18 9 750 1.40 180 SDCL1005C82N □TDF 82 8 10010 13 - 750 2.40 150 SDCL1005CR10□TDF 100 8 10010 12 - 700 2.60 150SDCL1005CR12□TDF 120 8 10010 - - 600 2.80 150SDCL1005CR15□TDF 150 8 10010 - - 550 3.20 100 SDCL1005CR18□TDF 180 8 10010 - - 500 3.70 100 SDCL1005CR22□TDF 220 8 10012 - - 450 4.00 100 SDCL1005CR27□TDF 270 8 10012 - - 400 4.50 100 SDCL1005CR33□TDF 330 6 50 - - - 350 7.00 500.5±0.15[.020±.006]※□: Please specify the inductance tolerance code (J=±5%, K=±10%). The product with tolerance less than ±5%, ±10% isalso available. Please contact your local sales.SPECIFICATIONSSDCL1608-D TYPETypical Q @ Freq. (MHz)Part NumberInductanceMin. Qual i t y FactorL,Q Test Freq. L/Q1008001000Min.Self-resonantFrequencyMax. DC Resistance Max.RatedCurrentThicknessUnits nH - MHz - MHz Ω mA mm [inch]SymbolL Q Freq Q S.R.F DCR Ir T SDCL1608C1N0STDF 1.0±0.38 100 13 70 80 10000 0.05 500 SDCL1608C1N2STDF 1.2±0.38 100 13 60 70 10000 0.05 500 SDCL1608C1N5STDF 1.5±0.38 100 13 47 68 6000 0.10 500 SDCL1608C1N8STDF 1.8±0.38 100 13 45 61 6000 0.10 500 SDCL1608C2N2STDF 2.2±0.38 100 13 45 60 6000 0.10 500 SDCL1608C2N7STDF 2.7±0.310 100 13 44 55 6000 0.12 500 SDCL1608C3N3STDF 3.3±0.310 100 13 43 50 6000 0.15 500 SDCL1608C3N9STDF 3.9±0.310 100 13 43 50 6000 0.16 500 SDCL1608C4N7STDF 4.7±0.310 100 13 43 50 6000 0.20 500 SDCL1608C5N6STDF 5.6±0.310 100 14 42 48 5000 0.25 500 SDCL1608C6N8□TDF 6.8 10 100 14 43 50 5000 0.30 500 SDCL1608C8N2□TDF 8.2 10 100 14 43 48 4500 0.35 500 SDCL1608C10N □TDF 10 12 100 15 45 50 3500 0.40 300 SDCL1608C12N □TDF 12 12 100 18 48 50 3000 0.45 300 SDCL1608C15N □TDF 15 12 100 18 48 50 2300 0.50 300 SDCL1608C18N □TDF 18 12 100 16 48 51 2200 0.55 300 SDCL1608C22N □TDF 22 12 100 16 45 48 2000 0.60 300 SDCL1608C27N □TDF 27 12 100 16 45 45 1700 0.65 300 SDCL1608C33N □TDF 33 12 100 16 45 41 1500 0.70 300SDCL1608C39N □TDF 39 12 100 17 40 48 1400 0.70 300 SDCL1608C47N □TDF 47 12 100 17 35 35 1200 0.70 300 SDCL1608C56N □TDF 56 12 100 17 35 30 1100 0.75 300 SDCL1608C68N □TDF 68 12 100 17 30 20 900 0.85 300 SDCL1608C82N □TDF 82 8 100 15 22 - 800 1.00 300 SDCL1608CR10□TDF 100 8 100 15 16 - 700 1.20 300 SDCL1608CR12□TDF* 120 8 50 15 - - 600 1.40 200 SDCL1608CR15□TDF* 150 8 50 15 - - 500 1.60 200 SDCL1608CR18□TDF* 180 8 50 15 - - 400 1.90 200 SDCL1608CR22□TDF* 220 8 50 15 - - 350 2.40 200 SDCL1608CR27□TDF* 270 8 50 16 - - 350 2.60 150 SDCL1608CR33□TDF* 330 8 50 16 - - 350 2.80 150 SDCL1608CR39□TDF* 390 8 50 16 - - 300 3.20 150 SDCL1608CR43□TDF* 430 8 50 16 - - 280 3.40 150 SDCL1608CR47□TDF* 470 8 50 15 - - 250 3.60 150 SDCL1608CR56□TDF* 560 8 50 15 - - 250 4.00 100 SDCL1608CR68□TDF*680 8 50 15 - - 250 4.50 1000.8±0.15[.031±.006]※□: Please specify the inductance tolerance code (J=±5%, K=±10%). The product with tolerance less than ±5%, ±10% isalso available. Please contact your local sales.※*: The length: 1.65±0.15mm, for others: 1.60±0.15mm.TYPICAL ELECTRICAL CHARACTERISTICSSDCL1005-D TYPE SDCL1005-D TYPEFrequency(MHz)I n d u c t a n c e (n H )Frequency(MHz)0QSDCL1608-D TYPE SDCL1608-D TYPEFrequency(MHz)I n d u c t a n c e (n H )Frequency(MHz)0Q。
EMC资料
深圳顺络电子股份有限公司
Sunlord EMC主要解决方法 EMC主要解决方法
I/O Filter Enclosure Shielding Design PCB EMC Design Internal Cable EMC Design
屏蔽 接地 印刷板设计 互连与搭接设计 EMI滤波（滤波器件：电感、磁珠、电容、滤波器等）
辐射耦合
减敏
EMC评定指标 评定指标
CS，CE ，
深圳顺络电子股份有限公司
RS，RE ，
Sunlord 电磁干扰抑制部位
高速信号线上的谐波、辐射噪声 微处理器、视频电路、时钟线、高频模拟电路、振荡器等 直流源处的高频噪声 电源的高频噪声和谐波 I/O接口、其他接口部位的噪声 电缆都是天线，电缆是干扰进出设备的有效途径 PCB布局 数字地与模拟地的去耦
SZ Series PZ Series HZ Series
高频噪声和大电流 HPZ series 线路
47～ 100 ～
500～ 3500 ～
深圳顺络电子股份有限公司
Sunlord
磁珠频谱图及衰减特性图( 磁珠频谱图及衰减特性图(I)
GZ频谱图 频谱图
GZ2012D601
GZ衰减特性图 衰减特性图
功能 滤波吸收元件 滤波模块元件 滤波模块元件 阻抗匹配 滤波模块元件 阻抗匹配
0603(0201) SDCL ~2012(0805)
1nH~470nH
1005(0402) SDHL ~1608(0603)
1nH~180nH
深圳顺络电子股份有限公司
Sunlord 电感的使用频段
产品类型
SDFL SDCL SDHL 使用频率
工频及音频干扰 甚低频干扰 载频干扰
SUNLORDINC顺络电子20200515 CN-Sunlord PPT_已签章
2019年位居全球片式绕线电感产能第三位
深圳市首批科技创新行业龙头企业 电感行业国内第一，处于绝对领先地位
2019年“中国电子元件百强企业” 排名27位
片式电感产品全球市场份额超过10%
Page 7 of 26
财务总监 徐佳
总工程师 郭海
汽车电子副总裁 李家凯
副总裁 高海明
绕线产品 厂房 D
叠层产品 厂房 A
LTCC 技术产品 厂房 B
天线产品 厂房 C
Page 4 of 26
贵阳工厂
位置: 贵州省贵阳 厂房面积: 38,000 ㎡ 员工人数: 711人（2019年12月） 获得证书: ISO9001/GJB9001 产 品 线: 片式绕线电感、 功率电感、变压器
东莞工厂2（建设中）
小型化
大电流
模块
LTCC产品
车规级
Page 20 of 26
CNAS认可实验室 符合ISO/ IEC17025:2005 要求
符合UL认证实验室
“顺络-是德”电子测量联 合实验室
材料分析
扫描电镜， X-射线荧光光谱测量机， 热重分析仪， 等等
失效分析
抛光研磨机， X-Ray CT仪， 探针台， 等等
Page 12 of 26
氧化锆陶瓷产品
手机背板、智能穿戴壳体、指纹识别盖片
PDS 天线
NFC 产品
磁性片、柔性天线
PCB
4~8层通孔&二阶HDI板
Page 13 of 26
6
7
8
1
3 4 5
1 LED灯 2 电池管理系统 3 信息娱乐系统 4 驾驶辅助系统 2 5 T-BOX 6 车载充电 7 DC/DC 转换 8 电机驱动
顺络贴片电感选型手册
绕线贴片功率电感—ASWPA 系列Wire Wound SMD Power Inductors – ASWPA SeriesOperating temperature range: -40℃~+125℃ (Including self-heating)特征 FEATURES● 磁性胶水涂敷结构极大减少了蜂鸣声● 直接在磁芯上金属化电极，抗跌落冲击强，经 久耐用● 闭合磁路结构设计，漏磁少，抗EMI 能力强● 同等尺寸，额定电流特性较传统电感高出30% 以上● AEC-Q200D 认证用途 APPLICATIONS● 车载信息娱乐系统 ● LED 灯 ● 安全气囊● 除汽车电源系统以外的DC-DC 转换器产品型号 PRODUCT IDENTIFICATIONASWPA 4035 S 1R0 N T □□□① ② ③ ④ ⑤ ⑥ ⑦● Magnetic-resin shielded construction reduces buzz noise to ultra-low levels● Metallization on ferrite core results in excellent shock resistance and damage-free durability ● Closed magnetic circuit design reduces leakage flux and Electro Magnetic Interference (EMI) ● 30% higher current rating than conventional inductors of equal size ● AEC-Q200D verified● Infotainment system ● LED Lighting ● Airbag● DC-DC conversion except for vehicle power外观尺寸 SHAPE AND DIMENSIONSFig.1 Fig.2规格特性 SPECIFICATIONSNote: ※ 1: Rated current: Isat (max.) or Irms (max.), whichever is smaller;※ 2: Saturation Current: Max. Value, DC current at which the inductance drops less than 20% from its value without current; Typ. Value, DC current at which the inductance drops 30% from its value without current;※ 3: Heat Rating Current: DC current that causes the temperature rise (ΔT) from 20°C ambient. For Max. Value, ΔT＜40℃; For Typ. Value, ΔT is approximate 40℃.The part temperature (ambient + temp. rise) should not exceed 125 °C under worst case operating conditions. Circuit design, component placement, PCB trace size and thickness, airflow and other cooling provisions all affect the part temperature. Part temperature should be verified in the end application。
顺络电感规格书
Wire Wound SMD Power Inductors – SWPA SeriesOperating temperature range: -40℃~+125℃ (Including self-heating)FEATURES● Magnetic-resin shielded construction reduces buzz noise to ultra-low levels● Metallization on ferrite core results in excellent shock resistance and damage-free durability ● Closed magnetic circuit design reduces leakage flux and Electro Magnetic Interference (EMI) ● 30% higher current rating than conventional inductors of equal size ● Takes up less PCB real estate and save more powerAPPLICATIONS● Smart phone, smart TV, set top box, notebook ● Car navigation systems, telecomm base stations ● VR, AR ● LED lightingPRODUCT IDENTIFICATIONSWPA 3012 S 1R0 N T□□□① ② ③ ④ ⑤ ⑥ ⑦②(L×W×H) [mm]External Dimensions (L×W×H) [mm]252010 2.5×2.0×1.0 252012 2.5×2.0×1.23010 3.0×3.0×1.0 3012 3.0×3.0×1.2 3015 3.0×3.0×1.5 4010 4.0×4.0×1.0 4012 4.0×4.0×1.2 4018 4.0×4.0×1.8 4020 4.0×4.0×2.0 4026 4.0×4.0×2.6 4030 4.0×4.0×3.0 5012 5.0×5.0×1.2 5020 5.0×5.0×2.0 5040 5.0×5.0×4.0 5045 5.0×5.0×4.5 6020 6.0×6.0×2.0 6028 6.0×6.0×2.8 6040 6.0×6.0×4.0 6045 6.0×6.0×4.5 8040 8.0×8.0×4.0 8050 8.0×8.0×5.0 8065 8.0×8.0×6.5①Type SWPAWire Wound SMD Power Inductor③ Feature TypeS Standard ④ Nominal InductanceExample Nominal Value1R0 1.0μH 100 10μH⑤ Inductance ToleranceK ±10%M ±20% N ±30% ⑥PackingTTape Carrier Package⑦ Design Code □□□Standard product is blank微亨电子赵先生 销售经理 ＱＱ：３００２２６８４１７SHAPE AND DIMENSIONSFig.1 Fig.2Unit: mmSeries Shape A B C D E F a Typ. b Typ.c Typ.SWPA252010S Fig.1 2.5±0.1 2.0±0.1 1.0 Max. 1.5±0.20.80±0.20.80±0.2 0.80 0.85 2.0 SWPA252012S Fig.1 2.5±0.1 2.0±0.1 1.2 Max. 1.5±0.20.80±0.20.80±0.2 0.80 0.85 2.0 SWPA3010S Fig.2 3.0±0.2 3.0±0.2 1.0 Max. 2.5±0.20.75±0.2 1.5±0.2 1.5 0.8 2.7 SWPA3012S Fig.2 3.0±0.2 3.0±0.2 1.2 Max. 2.5±0.20.75±0.2 1.5±0.2 1.5 0.8 2.7 SWPA3015S Fig.2 3.0±0.2 3.0±0.2 1.5 Max. 2.5±0.20.75±0.2 1.5±0.2 1.5 0.8 2.7 SWPA4010S Fig.2 4.0±0.2 4.0±0.2 1.0 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4012S Fig.2 4.0±0.2 4.0±0.2 1.2 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4018S Fig.2 4.0±0.2 4.0±0.2 1.8 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4020S Fig.2 4.0±0.2 4.0±0.2 2.0 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4026S Fig.2 4.0±0.2 4.0±0.2 2.6 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA4030S Fig.2 4.0±0.2 4.0±0.2 3.0 Max. 3.3±0.20.95±0.2 2.1±0.2 1.9 1.1 3.7 SWPA5012S Fig.3 5.0±0.2 5.0±0.2 1.2 Max. 4.0±0.2 1.25±0.2 2.5±0.2 2.3 1.4 4.2 SWPA5020S Fig.3 5.0±0.2 5.0±0.2 2.0 Max. 4.0±0.2 1.25±0.2 2.5±0.2 2.3 1.4 4.2 SWPA5040S Fig.3 5.0±0.2 5.0±0.2 4.0 Max. 4.0±0.2 1.25±0.2 2.5±0.2 2.3 1.4 4.2 SWPA5040S Fig.3 5.0±0.2 5.0±0.2 4.5 Max. 4.0±0.2 1.25±0.2 2.5±0.2 2.3 1.4 4.2 SWPA6020S Fig.2 6.0±0.3 6.0±0.3 2.0 Max. 4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.7 5.7 SWPA6028S Fig.2 6.0±0.3 6.0±0.3 2.8 Max. 4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.7 5.7 SWPA6040S Fig.2 6.0±0.3 6.0±0.3 4.0 Max. 4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.7 5.7 SWPA6045S Fig.2 6.0±0.3 6.0±0.3 4.5 Max. 4.9±0.3 1.55±0.3 2.9±0.3 2.8 1.7 5.7 SWPA8040S Fig.2 8.0±0.3 8.0±0.3 4.2 Max. 6.3±0.3 2.00±0.3 4.0±0.3 3.8 2.2 7.5 SWPA8050S Fig.3 8.0±0.3 8.0±0.3 5.0 Max. 6.3±0.3 2.00±0.3 4.0±0.3 3.8 2.2 7.5 SWPA8065S Fig.3 8.0±0.3 8.0±0.3 6.5 Max.6.3±0.32.00±0.34.0±0.3 3.8 2.2 7.5※*1: All products are printed with Marking except the 252010S, 252012S, 3010S, 3012S and 3015S series.Part Number Frequency*3Current*4@100kHz,1V Max. Typ. Min. Max. Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat IrmsSWPA252010SR47NT 0.47±30% 0.056 0.047206 2.503.352.352.56 SWPA252010SR56NT 0.56±30% 0.072 0.060160 2.903.202.002.18 SWPA252010SR68NT 0.68±30% 0.074 0.062129 2.202.752.002.18 SWPA252010S1R0NT 1.0±30% 0.108 0.090100 1.852.201.651.80 SWPA252010S1R5NT 1.5±30% 0.182 0.15281 1.802.101.301.42 SWPA252010S2R2NT2.2±30% 0.209 0.17461 1.201.601.201.31 SWPA252010S3R3MT 3.3±20% 0.328 0.27347 1.051.300.900.98 SWPA252010S4R7MT 4.7±20% 0.563 0.46942 0.951.150.700.76 SWPA252010S5R6MT 5.6±20% 0.563 0.46935 0.800.950.730.80 SWPA252010S6R8MT 6.8±20% 0.896 0.74731 0.780.920.590.64 SWPA252010S100MT 10±20% 1.092 0.91027 0.650.780.500.55 SWPA252012S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat IrmsSWPA252012SR47NT 0.47±30% 0.0610.047160 3.82 4.27 2.15 2.34 SWPA252012SR68NT 0.68±30% 0.0740.057140 3.28 3.68 1.95 2.13 SWPA252012S1R0NT 1.0±30% 0.0900.069110 2.59 2.90 1.93 2.10 SWPA252012S1R2NT 1.2±30% 0.1290.099100 2.38 2.67 1.46 1.59 SWPA252012S1R5MT 1.5±20% 0.1470.11397 2.24 2.51 1.40 1.53 SWPA252012S1R5NTY01 1.5±30% 0.1300.10063 1.80 2.00 1.45 1.58 SWPA252012S2R2MT 2.2±20% 0.2160.16669 1.85 2.07 1.15 1.25 SWPA252012S2R2NTY02 2.2±30% 0.1530.11853 1.55 1.75 1.30 1.42 SWPA252012S2R7MT 2.7±20% 0.2390.18463 1.72 1.92 1.09 1.19 SWPA252012S3R3MT 3.3±20% 0.2640.20362 1.61 1.80 1.04 1.13 SWPA252012S3R6MT 3.6±20% 0.3480.26853 1.46 1.64 0.90 0.98 SWPA252012S4R3MT 4.3±20% 0.3770.29051 1.37 1.53 0.87 0.95 SWPA252012S4R7MT 4.7±20% 0.3770.29047 1.12 1.25 0.84 0.92 SWPA252012S5R1MT 5.1±20% 0.5000.38544 1.23 1.37 0.75 0.82 SWPA252012S5R6MT 5.6±20% 0.5380.41438 1.111.250.730.80 SWPA252012S6R2MT 6.2±20% 0.5420.41738 1.03 1.16 0.73 0.80 SWPA252012S6R8MT 6.8±20% 0.5810.44738 0.98 1.09 0.69 0.75 SWPA252012S7R5MT 7.5±20% 0.6110.47035 0.97 1.09 0.68 0.74 SWPA252012S8R2MT 8.2±20% 0.6580.50636 0.98 1.10 0.65 0.71 SWPA252012S9R1MT 9.1±20% 0.6900.53134 0.91 1.02 0.62 0.68 SWPA252012S100MT 10±20% 0.6900.53134 0.79 0.88 0.62 0.68 SWPA252012S120MT 12±20% 1.0750.82728 0.78 0.88 0.51 0.56 SWPA252012S150MT 15±20% 1.591 1.22425 0.68 0.77 0.42 0.46 SWPA252012S220MT 22±20% 1.976 1.52020 0.53 0.59 0.38 0.41Part Number Frequency*3Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA3010S1R0NT 1.0±30% 0.0850.065180 1.402.101.451.80SWPA3010S1R2NT 1.2±30% 0.0850.065137 1.251.701.451.80SWPA3010S1R5NT 1.5±30% 0.1040.080120 1.271.701.301.60SWPA3010S2R2NT 2.2±30% 0.1430.110100 1.151.501.091.40SWPA3010S2R7NT 2.7±30% 0.1690.13090 1.001.201.021.40SWPA3010S3R3NT 3.3±30% 0.1890.14574 0.971.200.961.20SWPA3010S3R6MT 3.6±20% 0.2150.16567 0.951.200.901.10SWPA3010S4R7MT 4.7±20% 0.2930.22559 0.751.050.771.10SWPA3010S5R6MT 5.6±20% 0.3220.248 40 0.580.650.701.05SWPA3010S6R8MT 6.8±20% 0.3970.30542 0.550.720.660.96SWPA3010S8R2MT 8.2±20% 0.5200.400 23 0.550.700.580.70SWPA3010S100MT 10±20% 0.5200.40039 0.550.750.580.70SWPA3010S120MT 12±20% 0.6570.50536 0.430.650.520.67SWPA3010S150MT 15±20% 0.7930.61030 0.420.570.470.57SWPA3010S220MT 22±20% 1.2090.93028 0.350.480.380.52SWPA3010S270MT 27±20% 1.404 1.08025 0.300.450.350.50SWPA3010S330MT 33±20% 2.015 1.55018 0.290.420.300.55SWPA3010S390MT 39±20% 2.275 1.75018 0.280.380.280.53SWPA3010S430MT 43±20% 2.340 1.80018 0.230.360.270.52SWPA3010S470MT 47±20% 2.535 1.95018 0.220.350.260.52SWPA3010S510MT 51±20% 2.860 2.20018 0.210.330.250.48SWPA3010S560MT 56±20% 3.016 2.32016 0.210.280.240.35 SWPA3012S SeriesPart Number Inductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat IrmsSWPA3012SR22NT 0.22±30% 0.022 0.017 321 5.306.003.003.30 SWPA3012SR82NT 0.82±30% 0.039 0.030 180 2.05 2.80 2.47 3.00SWPA3012S1R0NT 1.0±30% 0.0520.040 120 1.87 2.80 2.20 2.70SWPA3012S1R2NT 1.2±30% 0.0590.045 120 2.22 2.50 2.01 2.20SWPA3012S1R5NT 1.5±30% 0.0590.045 110 1.62 1.90 2.01 2.20SWPA3012S1R8NT 1.8±30% 0.0820.063 90 1.30 1.90 1.65 1.80SWPA3012S2R2NT 2.2±30% 0.0980.075 84 1.20 1.90 1.55 1.70SWPA3012S2R4NT 2.4±30% 0.0880.068 100 1.15 1.50 1.60 1.70SWPA3012S2R7NT 2.7±30% 0.1100.085 65 1.14 1.50 1.48 1.50SWPA3012S3R3MT 3.3±20% 0.1300.100 64 1.05 1.50 1.36 1.40SWPA3012S3R6MT 3.6±20% 0.1300.100 36 1.05 1.50 1.36 1.40SWPA3012S3R9MT 3.9±20% 0.189 0.145 61 1.00 1.30 1.24 1.30SWPA3012S4R7MT 4.7±20% 0.1560.120 61 0.901.001.241.30 SWPA3012S5R6MT 5.6±20% 0.2260.17461 0.801.101.131.24 SWPA3012S6R8MT 6.8±20% 0.2470.190 61 0.75 0.90 0.98 1.10SWPA3012S100MT 10±20% 0.3450.265 42 0.60 0.88 0.83 0.90SWPA3012S120MT 12±20% 0.4490.345 32 0.48 0.67 0.73 0.84SWPA3012S150MT 15±20% 0.4680.360 27 0.45 0.62 0.71 0.77SWPA3012S180MT 18±20% 0.7090.545 25 0.43 0.59 0.58 0.65SPECIFICATIONS SWPA3012S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA3012S220MT 22±20% 0.8390.645 23 0.42 0.52 0.53 0.59SWPA3012S270MT 27±20% 1.1310.870 21 0.35 0.48 0.47 0.51SWPA3012S330MT 33±20% 1.1380.875 18 0.36 0.46 0.46 0.50SWPA3012S360MT 36±20% 1.2350.950 18 0.34 0.44 0.44 0.48SWPA3012S390MT 39±20% 1.7291.330 18 0.30 0.39 0.37 0.41SWPA3012S470MT 47±20% 1.8851.450 14 0.27 0.35 0.35 0.40SWPA3012S560MT 56±20% 1.794 1.380 9 0.260.330.280.40SWPA3012S680MT 68±20% 2.171 1.670 7 0.24 0.29 0.33 0.37 SWPA3012S820MT 82±20% 3.302 2.540 7 0.17 0.27 0.27 0.31 SWPA3012S101MT 100±20% 3.718 2.860 5 0.21 0.23 0.25 0.29 SWPA3015S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat IrmsSWPA3015SR50NT 0.5±30% 0.0390.030 162 3.90 4.20 2.60 2.80 SWPA3015S1R0NT 1.0±30% 0.0390.030 150 2.32 2.80 2.35 2.50 SWPA3015S1R2NT 1.2±30% 0.0520.040 110 2.21 3.10 1.95 2.30 SWPA3015S1R5NT 1.5±30% 0.0650.050 100 2.30 2.70 1.70 2.20 SWPA3015S1R8NT 1.8±30% 0.0650.050 92 1.75 2.20 1.70 2.20 SWPA3015S2R2NT 2.2±30% 0.0780.060 86 1.60 2.00 1.60 2.00 SWPA3015S2R7NT 2.7±30% 0.0980.075 64 1.52 1.90 1.43 1.90 SWPA3015S3R3MT 3.3±20% 0.104 0.080 68 1.32 1.81 1.36 1.60 SWPA3015S3R6MT 3.6±20% 0.137 0.105 59 1.28 1.60 1.20 1.50 SWPA3015S3R9MT 3.9±20% 0.137 0.105 47 1.20 1.40 1.20 1.50 SWPA3015S4R3MT 4.3±20% 0.150 0.115 53 1.20 1.40 1.14 1.30 SWPA3015S4R7MT 4.7±20% 0.163 0.125 46 1.10 1.40 1.09 1.30 SWPA3015S5R1MT 5.1±20% 0.173 0.133 49 1.00 1.20 1.05 1.20 SWPA3015S6R2MT 6.2±20% 0.254 0.195 46 1.00 1.20 0.86 1.00 SWPA3015S6R8MT 6.8±20% 0.260 0.200 39 0.85 1.10 0.85 1.10 SWPA3015S100MT 10±20% 0.3250.250 41 0.72 0.92 0.77 0.90 SWPA3015S120MT 12±20% 0.4160.320 32 0.70 0.90 0.68 0.89 SWPA3015S150MT 15±20% 0.4550.350 30 0.66 0.88 0.65 0.72 SWPA3015S180MT 18±20% 0.5590.430 23 0.56 0.72 0.59 0.72 SWPA3015S220MT 22±20% 0.5980.460 23 0.52 0.68 0.57 0.69 SWPA3015S270MT 27±20% 0.9490.730 22 0.48 0.56 0.45 0.56 SWPA3015S330MT 33±20% 1.0660.820 20 0.44 0.53 0.43 0.51 SWPA3015S390MT 39±20% 1.2940.995 14 0.41 0.55 0.39 0.44 SWPA3015S430MT 43±20% 1.3781.060 16 0.37 0.43 0.37 0.48 SWPA3015S470MT 47±20% 1.6251.250 14 0.35 0.43 0.35 0.44 SWPA3015S560MT 56±20% 1.6641.280 13 0.33 0.42 0.34 0.41 SWPA3015S620MT 62±20%2.0931.610 13 0.30 0.40 0.30 0.41 SWPA3015S680MT 68±20% 3.5102.700 11 0.28 0.37 0.23 0.31 SWPA3015S101MT 100±20% 4.0433.110 6.3 0.23 0.25 0.21 0.25 SWPA3015S151MT 150±20%4.940 3.800 4.7 0.18 0.22 0.19 0.23SPECIFICATIONS SWPA4010S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ.Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4010S1R0NT 1.0±30% 0.0670.056 116 2.00 2.30 1.90 2.40SWPA4010S1R5NT 1.5±30% 0.0840.070 94 1.68 2.00 1.70 2.00SWPA4010S2R2MT 2.2±20% 0.102 0.085 73 1.20 1.50 1.50 2.00 SWPA4010S3R3MT 3.3±20% 0.120 0.100 58 1.10 1.40 1.40 1.80 SWPA4010S4R7MT 4.7±20% 0.168 0.140 47 0.95 1.10 1.20 1.50 SWPA4010S6R8MT 6.8±20% 0.240 0.200 38 0.80 0.95 1.00 1.20 SWPA4010S100MT 10±20% 0.3600.300 31 0.62 0.75 0.75 1.00SWPA4010S150MT 15±20% 0.5160.430 24 0.54 0.61 0.60 0.85SWPA4010S220MT 22±20% 0.6840.570 19 0.45 0.52 0.50 0.75 SWPA4012S SeriesPart Number Inductance DC Resistance Self-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4012SR82NT 0.82±30% 0.065 0.050 150 3.02 3.30 1.65 2.50 SWPA4012S1R0NT 1.0±30% 0.0650.050 120 2.61 3.20 1.65 2.50 SWPA4012S1R5NT 1.5±30% 0.0850.065 90 2.10 2.70 1.46 2.20 SWPA4012S1R8NT 1.8±30% 0.1040.080 88 2.12 2.60 1.32 1.90 SWPA4012S2R2NT 2.2±30% 0.1040.080 74 1.76 2.30 1.32 1.90 SWPA4012S2R7NT 2.7±30% 0.117 0.090 71 1.90 2.30 1.25 1.70 SWPA4012S3R3NT 3.3±30% 0.143 0.110 60 1.72 2.10 1.12 1.60 SWPA4012S3R6NT 3.6±30% 0.143 0.110 57 1.20 1.70 1.12 1.60 SWPA4012S4R3NT 4.3±30% 0.1820.140 54 1.58 1.70 1.00 1.50 SWPA4012S4R7NT 4.7±30% 0.1630.125 50 1.15 1.80 1.05 1.50 SWPA4012S5R1NT 5.1±30% 0.2010.155 50 1.55 1.60 0.95 1.50 SWPA4012S5R6NT 5.6±30% 0.1820.140 42 1.00 1.60 1.00 1.20 SWPA4012S6R8MT 6.8±20% 0.257 0.198 40 0.85 1.40 0.84 1.20 SWPA4012S100MT 10±20% 0.345 0.265 33 0.80 1.10 0.77 1.00 SWPA4012S120MT 12±20% 0.377 0.290 32 0.66 1.00 0.70 0.95 SWPA4012S150MT 15±20% 0.442 0.340 25 0.56 0.80 0.64 0.85 SWPA4012S180MT 18±20% 0.611 0.470 23 0.55 0.75 0.55 0.80 SWPA4012S220MT 22±20% 0.763 0.587 20 0.46 0.70 0.49 0.75 SWPA4012S270MT 27±20% 0.936 0.720 18 0.50 0.70 0.45 0.60 SWPA4012S330MT 33±20% 1.053 0.810 17 0.42 0.60 0.42 0.58 SWPA4012S360MT 36±20% 1.170 0.900 14 0.40 0.50 0.40 0.56 SWPA4012S390MT 39±20% 1.430 1.100 16 0.55 0.66 0.37 0.50 SWPA4012S470MT 47±20% 1.430 1.100 12 0.35 0.50 0.37 0.50 SWPA4012S560MT 56±20% 1.625 1.250 11 0.33 0.45 0.33 0.46 SWPA4012S680MT 68±20% 2.535 1.950 11 0.38 0.45 0.27 0.45 SWPA4012S820MT 82±20% 2.782 2.140 11 0.28 0.40 0.26 0.36 SWPA4012S101MT 100±20% 2.873 2.210 9.4 0.25 0.30 0.25 0.35Part Number Frequency*3Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4018SR47NT 0.47±30% 0.0180.014155 4.30 5.20 4.00 4.50 SWPA4018SR68NT 0.68±30% 0.0260.020128 4.90 5.60 3.30 3.80 SWPA4018S1R0NT 1.0±30% 0.0330.02580 4.80 5.20 2.00 3.30 SWPA4018S1R5NT 1.5±30% 0.0390.03065 3.35 4.00 1.80 3.20 SWPA4018S1R8NT 1.8±30% 0.0440.03454 3.00 3.40 2.00 2.80 SWPA4018S2R2MT 2.2±20% 0.0590.04552 2.70 3.20 1.65 2.60 SWPA4018S3R3MT 3.3±20% 0.0910.07044 2.45 2.90 1.23 2.10 SWPA4018S4R7MT 4.7±20% 0.1170.09034 1.70 2.20 1.20 1.80 SWPA4018S6R8MT 6.8±20% 0.1430.11029 1.45 2.00 1.06 1.50 SWPA4018S100MT 10±20% 0.2340.18024 1.30 1.60 0.84 1.20 SWPA4018S150MT 15±20% 0.3250.25019 0.94 1.10 0.65 1.00 SWPA4018S220MT 22±20% 0.4680.36016 0.80 0.88 0.59 0.85 SWPA4018S270MT 27±20% 0.6110.47027 0.47 0.62 0.52 0.90 SWPA4018S330MT 33±20% 0.6890.53012 0.56 0.75 0.49 0.72 SWPA4018S470MT 47±20% 0.8450.65010 0.57 0.70 0.42 0.65 SWPA4018S680MT 68±20% 1.300 1.0008.3 0.47 0.51 0.32 0.52 SWPA4018S101MT 100±20% 2.275 1.750 6.5 0.40 0.44 0.25 0.41 SWPA4018S151MT 150±20% 3.250 2.500 5.5 0.31 0.34 0.22 0.36 SWPA4018S221MT 220±20% 5.200 4.000 4 0.27 0.30 0.17 0.27 SWPA4020S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat IrmsSWPA4020SR24MT 0.24±20% 0.0140.011283 10.5 12.5 4.50 5.20 SWPA4020SR33NT 0.33±30% 0.0160.013223 7.50 8.50 3.30 4.90 SWPA4020SR47NT 0.47±30% 0.0290.022160 7.00 7.50 3.30 3.70 SWPA4020SR68NT 0.68±30% 0.0360.028120 6.40 6.60 2.80 3.30 SWPA4020S1R0NT 1.0±30% 0.0380.02975 4.78 5.20 2.15 3.20 SWPA4020S1R2NT 1.2±30% 0.0380.02972 5.10 5.60 2.15 3.20 SWPA4020S1R5NT 1.5±30% 0.0460.03571 4.45 4.90 1.98 3.00 SWPA4020S2R2NT 2.2±30% 0.0520.04049 3.40 3.70 1.85 2.80 SWPA4020S3R3MT 3.3±20% 0.0910.07044 3.20 3.50 1.40 2.50 SWPA4020S3R6MT 3.6±20% 0.0720.05549 2.80 3.00 1.54 2.50 SWPA4020S4R7MT 4.7±20% 0.0980.07542 2.35 2.50 1.34 2.00 SWPA4020S5R1MT 5.1±20% 0.111 0.08542 2.30 2.50 1.27 1.80 SWPA4020S5R6MT 5.6±20% 0.1170.09030 2.20 2.40 1.22 1.80 SWPA4020S6R2MT 6.2±20% 0.1500.11536 2.15 2.30 1.08 1.60 SWPA4020S6R8MT 6.8±20% 0.1630.12533 2.20 2.40 1.04 1.60 SWPA4020S7R5MT 7.5±20% 0.1500.11530 1.85 2.00 1.08 1.50 SWPA4020S8R2MT 8.2±20% 0.1630.12527 1.75 1.90 1.04 1.40 SWPA4020S100MT 10±20% 0.2150.16526 1.60 1.70 0.90 1.20 SWPA4020S120MT 12±20% 0.2280.17526 1.50 1.60 0.88 1.20 SWPA4020S150MT 15±20% 0.2990.23024 1.35 1.50 0.77 1.10 SWPA4020S220MT 22±20% 0.4550.35015 1.05 1.10 0.62 0.87 SWPA4020S270MT 27±20% 0.7090.54514 1.02 1.10 0.50 0.70Part Number Frequency*3Current*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4020S330MT 33±20% 0.7150.55011 0.850.930.490.68SWPA4020S390MT 39±20% 0.8450.65011 0.820.900.460.64SWPA4020S430MT 43±20% 0.8580.66010 0.770.850.450.63SWPA4020S470MT 47±20% 0.9230.71010 0.740.810.440.61SWPA4020S510MT 51±20% 0.9750.75010 0.700.770.420.59SWPA4020S560MT 56±20% 1.0400.80010 0.660.720.410.57SWPA4020S620MT 62±20% 1.1700.9009.6 0.650.710.390.52SWPA4020S680MT 68±20% 1.380 1.0607.7 0.610.670.360.50SWPA4020S750MT 75±20% 1.510 1.1607.7 0.700.770.350.49SWPA4020S820MT 82±20% 1.520 1.1707.2 0.500.550.340.47SWPA4020S101MT 100±20% 2.020 1.550 6.3 0.480.530.310.43 SWPA4026S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4026S1R0NT 1.0±30% 0.0310.024151 3.303.803.003.30SWPA4026S1R2NT 1.2±30% 0.0390.030120 3.103.402.303.30SWPA4026S1R5NT 1.5±30% 0.0390.030100 2.402.902.303.10SWPA4026S2R2MT 2.2±20% 0.0520.04096 2.102.402.003.80SWPA4026S3R3MT 3.3±20% 0.0650.05058 1.802.001.702.50SWPA4026S4R7MT 4.7±20% 0.0720.05546 1.451.701.602.30SWPA4026S6R8MT 6.8±20% 0.0850.06533 1.301.501.502.00SWPA4026S100MT 10±20% 0.1100.08526 1.001.201.301.90SWPA4026S150MT 15±20% 0.1430.11019 0.901.001.101.50SWPA4026S220MT 22±20% 0.2140.16513 0.600.800.901.40SWPA4026S330MT 33±20% 0.3510.2709 0.550.650.701.00SWPA4026S470MT 47±20% 0.3900.300 6 0.400.550.650.90 SWPA4030S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4030SR68NT 0.68±30% 0.0130.010130 6.80 8.00 4.56 5.10 SWPA4030SR91NT 0.91±30% 0.0170.013100 6.25 6.80 4.15 4.70 SWPA4030S1R0NT 1.0±30% 0.0180.01470 5.26 5.70 4.15 4.70 SWPA4030S1R2NT 1.2±30% 0.0200.01580 5.80 6.30 3.82 4.20 SWPA4030S1R5NT 1.5±30% 0.0260.02062 4.84 5.30 3.34 3.60 SWPA4030S1R8NT 1.8±30% 0.0330.02560 5.40 5.80 3.20 3.30 SWPA4030S2R2NT 2.2±30% 0.0390.03052 4.90 5.80 2.95 3.20 SWPA4030S3R3MT 3.3±20% 0.0520.04038 3.30 3.60 2.40 2.60 SWPA4030S3R6MT 3.6±20% 0.0520.04037 3.00 3.50 2.40 2.60 SWPA4030S3R9MT 3.9±20% 0.0740.05732 3.00 3.30 2.10 2.30Part Number Inductance DC Resistance Self-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA4030S4R3MT 4.3±20% 0.072 0.05537 2.95 3.20 2.10 2.30 SWPA4030S4R7MT 4.7±20% 0.078 0.06031 2.90 3.20 2.00 2.30 SWPA4030S5R6MT 5.6±20% 0.085 0.06530 2.60 2.80 1.95 2.10 SWPA4030S6R8MT 6.8±20% 0.1170.09024 2.75 3.00 1.60 1.70 SWPA4030S7R5MT 7.5±20% 0.110 0.08526 2.20 2.40 1.65 1.80 SWPA4030S8R2MT 8.2±20% 0.117 0.09026 2.10 2.30 1.60 1.70 SWPA4030S100MT 10±20% 0.1300.10021 1.95 2.40 1.50 1.60 SWPA4030S120MT 12±20% 0.1750.13518 1.70 1.80 1.30 1.40 SWPA4030S150MT 15±20% 0.2470.19016 1.65 1.80 1.11 1.20 SWPA4030S180MT 18±20% 0.2600.20010 1.40 1.50 1.10 1.20 SWPA4030S220MT 22±20% 0.2920.22510 1.30 1.40 1.00 1.20 SWPA4030S270MT 27±20% 0.3380.26010 1.15 1.35 0.90 1.05 SWPA4030S330MT 33±20% 0.4290.33010 1.10 1.20 0.84 0.92 SWPA4030S360MT 36±20% 0.4360.3359.8 1.05 1.10 0.83 0.91 SWPA4030S390MT 39±20% 0.5660.43510 1.03 1.10 0.73 0.80 SWPA4030S470MT 47±20% 0.5790.4458.4 0.95 1.00 0.72 0.80 SWPA4030S510MT 51±20% 0.6110.4708.4 0.90 1.13 0.70 0.80 SWPA4030S560MT 56±20% 0.7220.5558.4 0.85 0.94 0.65 0.71 SWPA4030S620MT 62±20% 0.7610.5857 0.80 0.99 0.63 0.70 SWPA4030S680MT 68±20% 1.1280.8687 0.72 0.80 0.52 0.57 SWPA4030S750MT 75±20% 1.326 1.020 6.3 0.70 0.88 0.48 0.53 SWPA4030S820MT 82±20% 1.378 1.060 5.6 0.66 0.72 0.47 0.52 SWPA4030S910MT 91±20% 1.430 1.100 5.6 0.65 0.71 0.46 0.50 SWPA4030S101MT 100±20% 1.495 1.150 5.6 0.60 0.73 0.45 0.49 SWPA4030S121MT 120±20% 1.755 1.350 5.4 0.55 0.60 0.42 0.46 SWPA4030S151MT 150±20% 2.340 1.800 4 0.50 0.55 0.30 0.35 SWPA4030S221MT 220±20% 3.250 2.500 4.2 0.40 0.50 0.35 0.40 SWPA4030S331MT 330±20% 5.200 4.000 6.8 0.30 0.40 0.25 0.26 SWPA4030S471KT 470±10% 9.3607.200 2 0.30 0.35 0.20 0.23 SWPA4030S501MT 500±20% 9.027 6.944 2 0.28 0.30 0.15 0.20 SWPA4030S681MT 680±20% 9.8547.580 1.2 0.19 0.20 0.14 0.18SWPA5012S SeriesPart Number Inductance DC Resistance Self-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat IrmsSWPA5012SR22NT 0.22±30% 0.0340.028315 8.109.303.003.30 SWPA5012S1R0NT 1.0±30% 0.0680.0571034.40 4.70 2.00 2.40SWPA5012S1R5NT 1.5±30% 0.0860.07268 3.70 3.80 1.90 2.20SWPA5012S2R2NT 2.2±30% 0.1080.09050 3.10 3.20 1.70 2.00SWPA5012S3R3NT 3.3±30% 0.1510.12634 2.40 2.60 1.40 1.70SWPA5012S4R7NT 4.7±30% 0.1970.16431 2.20 2.30 1.30 1.50SWPA5012S6R8MT 6.8±20% 0.2940.24522 1.70 1.90 1.00 1.20SWPA5012S100MT 10±20% 0.4130.34417 1.40 1.50 0.85 1.00SWPA5012S150MT 15±20% 0.5230.43613 1.20 1.30 0.80 0.92Part NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat Irms SWPA5012S220MT 22±20% 0.8580.780 16 0.88 0.98 0.60 0.68 SWPA5020S SeriesPart NumberInductance DC ResistanceSelf-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat IrmsSWPA5020SR22NT 0.22±30% 0.0110.009280 9.0012.005.306.00 SWPA5020SR24NT 0.24±30% 0.0110.009248 8.0010.005.306.00 SWPA5020SR47NT 0.47±30% 0.0170.013160 6.15 6.70 4.60 5.00 SWPA5020SR56NT 0.56±30% 0.0220.017137 8.50 9.60 3.80 4.20 SWPA5020SR68MT 0.68±30% 0.0220.017120 5.50 6.00 4.00 4.40 SWPA5020SR75NT 0.75±30% 0.0220.017117 5.50 6.00 4.00 4.40 SWPA5020S1R0NT 1.0±30% 0.0260.020114 4.10 5.00 3.80 4.10 SWPA5020S1R2NT 1.2±30% 0.0290.02283 4.50 4.90 3.55 3.90 SWPA5020S1R5NT 1.5±30% 0.0340.02668 4.10 4.50 3.20 3.50 SWPA5020S2R2NT 2.2±30% 0.0420.03257 3.20 4.00 2.90 3.10 SWPA5020S2R7NT 2.7±30% 0.0490.03852 2.90 3.50 2.70 2.90 SWPA5020S3R0NT 3.0±30% 0.0490.03849 2.55 2.80 2.70 2.90 SWPA5020S3R3NT 3.3±30% 0.0560.04346 2.55 3.00 2.50 2.70 SWPA5020S3R6NT 3.6±30% 0.0560.04343 2.80 3.00 2.50 2.70 SWPA5020S3R9NT 3.9±30% 0.0560.04340 2.30 2.80 2.50 2.70 SWPA5020S4R3MT 4.3±20% 0.0740.05737 2.50 3.00 2.20 2.40 SWPA5020S4R7MT 4.7±20% 0.0740.05737 2.50 2.70 2.20 2.40 SWPA5020S5R1MT 5.1±20% 0.0830.06432 2.25 2.60 2.05 2.20 SWPA5020S5R6MT 5.6±20% 0.0830.06432 2.30 2.50 2.05 2.20 SWPA5020S6R8MT 6.8±20% 0.1080.08330 2.05 2.20 1.80 1.90 SWPA5020S7R5MT7.5±20% 0.1170.09026 1.85 2.00 1.75 1.90 SWPA5020S8R2MT8.2±20% 0.1270.09826 1.85 2.00 1.65 1.80 SWPA5020S9R1MT9.1±20% 0.1430.11024 1.70 1.80 1.55 1.70 SWPA5020S100MT 10±20% 0.1430.11024 1.70 1.80 1.55 1.70 SWPA5020S120MT 12±20% 0.1820.14022 1.50 1.60 1.40 1.50 SWPA5020S150MT 15±20% 0.2150.16520 1.35 1.40 1.25 1.30 SWPA5020S180MT 18±20% 0.2600.20016 1.25 1.30 1.15 1.20 SWPA5020S220MT 22±20% 0.2940.22614 1.15 1.20 1.10 1.20 SWPA5020S330MT 33±20% 0.5070.39010 0.92 1.00 0.90 0.99 SWPA5020S470MT 47±20% 0.6800.5237 0.77 0.84 0.77 0.84 SWPA5020S560MT 56±20% 0.8190.630 6 0.77 0.84 0.70 0.77 SWPA5020S680MT 68±20% 0.9620.740 6 0.65 0.70 0.64 0.70 SWPA5020S820MT 82±20% 1.1580.965 6 0.65 0.75 0.50 0.60 SWPA5020S101MT 100±20% 1.430 1.100 6 0.53 0.58 0.53 0.58 SWPA5020S121MT 120±20% 1.755 1.350 6 0.42 0.53 0.40 0.50 SWPA5020S201MT 200±20% 2.600 2.000 4.5 0.30 0.33 0.40 0.45Part Number Inductance DC Resistance Self-resonantFrequencySaturation Current*3Heat RatingCurrent*4@100kHz,1V Max.Typ. Min. Max.Typ. Max. Typ.Units μH ΩMHz A ASymbol L DCR S.R.F Isat IrmsSWPA5040SR22MT 0.22±20% 0.0080.006289 18.0020.006.507.50 SWPA5040SR24NT 0.24±30% 0.0080.006251 15.7018.006.407.40 SWPA5040SR47MT 0.47±20% 0.0090.007171 10.0011.506.607.60 SWPA5040S1R0NT 1.0±30% 0.0160.012117 7.35 8.00 4.90 5.00SWPA5040S1R2NT 1.2±30% 0.0210.016110 6.50 7.00 4.15 4.25SWPA5040S1R5NT 1.5±30% 0.0200.01586 6.30 6.80 4.30 4.85SWPA5040S1R8MT 1.8±20% 0.0210.01655 5.50 6.05 4.15 4.30SWPA5040S2R2NT 2.2±30% 0.0250.01950 4.90 5.50 3.80 4.20SWPA5040S2R7NT 2.7±30% 0.0290.02237 4.30 4.80 3.60 4.00SWPA5040S3R0NT 3.0±30% 0.0290.02237 4.15 4.60 3.60 4.00SWPA5040S3R3NT 3.3±30% 0.0310.02432 3.95 4.45 3.40 3.90SWPA5040S3R6MT 3.6±20% 0.0340.02630 3.80 4.40 3.30 3.70SWPA5040S3R9NT 3.9±30% 0.0350.02729 3.55 4.00 3.20 3.70SWPA5040S4R7NT 4.7±30% 0.0390.03028 3.50 3.80 3.00 3.30SWPA5040S5R6MT 5.6±20% 0.0460.03527 3.00 3.70 2.80 3.10SWPA5040S6R8MT 6.8±20% 0.0560.04321 2.90 3.40 2.50 2.80SWPA5040S8R2MT 8.2±20% 0.0620.04820 2.70 2.90 2.30 2.60SWPA5040S100MT 10±20% 0.0830.06418 2.35 2.70 2.10 2.35SWPA5040S120MT 12±20% 0.1000.07714 2.22.52.02.1 SWPA5040S150MT 15±20% 0.1120.08613 2.00 2.20 2.00 2.05SWPA5040S180MT 18±20% 0.1550.11912 1.702.001.451.65 SWPA5040S220MT 22±20% 0.1680.12911 1.601.801.501.60 SWPA5040S270MT 27±20% 0.2440.1889.8 1.521.751.101.25 SWPA5040S330MT 33±20% 0.2440.1889 1.301.451.201.35 SWPA5040S470MT 47±20% 0.3540.2727 1.101.201.001.15 SWPA5040S510MT 51±20% 0.4940.380 6 1.001.201.001.10 SWPA5040S560MT 56±20% 0.4940.380 6 1.051.200.800.90 SWPA5040S680MT 68±20% 0.5200.400 6 0.901.000.800.90 SWPA5040S750MT 75±20% 0.5850.450 6 0.850.950.720.80 SWPA5040S101MT 100±20% 0.7280.560 5 0.750.850.700.78 SWPA5040S151MT 150±20% 0.9750.750 3.7 0.650.670.600.70 SWPA5040S221MT 220±20% 1.82 1.40 3.0 0.480.550.400.50 SWPA5040S301MT 300±20% 2.60 2.00 2.7 0.500.580.350.40 SWPA5040S331MT 330±20% 2.73 2.10 2.7 0.420.470.400.50 SWPA5040S471MT 470±20% 3.90 3.00 2.7 0.370.430.350.40 SWPA5040S561MT 560±20% 4.92 3.78 1.3 0.310.360.310.35 SWPA5040S681MT 680±20% 5.07 3.90 1.3 0.300.350.250.30 SWPA5040S102MT 1000±20% 7.800 6.000 1.3 0.210.250.200.23 SWPA5040S332MT 3300±20% 25.2021.000.9 0.1400.1500.1000.120SWPA5040S392MT 3900±20% 30.5523.500.8 0.1250.1500.1000.115SWPA5040S472MT 4700±20% 45.5035.000.6 0.1100.1300.0800.100SWPA5040S502MT 5000±20% 43.1635.970.49 0.1100.1300.0850.098SWPA5040S562MT 5600±20% 50.7039.000.49 0.1050.1200.0800.092SWPA5040S682MT 6800±20% 55.9043.000.38 0.0900.1100.0750.086SWPA5040S822MT 8200±20% 55.9043.000.38 0.0700.0850.0750.086SWPA5040S103MT 10000±20% 58.5045.000.32 0.0650.0750.0750.086。