常用管件管道配件中英文对照

合集下载

管道及配件中英文对照

管道及配件中英文对照化工管道词汇翻译1 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless(SMLS)steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe;straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbow长半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow(right hand or left hand) 双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee(right hand or 1eft hand)异径三通（分支口为异径）reducing tee (reducing on outlet)异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet)异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull head) 45°斜三通45°lateral管道及配件中英文对照245°斜三通（支管为异径）45°lateral (reducing on branch)45°斜三通(一个直通口为异径) 45°lateral(reducing on one run)45°斜三通(一个直通口及支管为异径) 45°lateral(reducing on one run and branch)Y 型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and outlet)异径四通（两个分支口为异径）reducing cross (reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run and both outlet)异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss(以上带红线的单词已经查过，应该是行业很组合的名词，可以查得到)。

管道专业常用英文对照

管道专业常用英文对照一、PIPE （管道/管子）二、FITTING （管件/连接件）3、 FTE ——内螺纹 MTE 外螺纹 TOE 一端螺纹 TBE 两端螺纹4、 EQ TEE ——等径三通5、 RED TEE ——异径三通6、 CONC.RED ——同心大小头7、 ECC.RED ——偏心大小头8、 RED.CPLG ——异径管接头9、 H.CPLG ——半管接头 F.CPLG ——管接头10、 HOSE CONNECTOR,FTE/FEMALE HOSE END ——软管接头 11、 NIPPLE TOE （NPT ）——螺纹管段 12、 CAP FTE(NPT)——螺纹管帽三、FLANGE （法兰）1、 BLIND ——盲板2、 RF/FF ——凸面/平面3、 SO/WN/LJ ——带颈平焊/带颈对焊/活套4、 STUB END ——翻边5、 MHRF/MH/MHRN ——需二次加工（详见相应图集）四、V ALES （阀门）1、 GA TE VL ——闸阀2、 GLOBE V ALVE ——截止阀3、 BALL V ALVE ——球阀4、 DIAPHRAGM V ALVE ——隔膜阀5、 PRESS SAFETY V ALVE ——安全阀6、 JACKETED V ALVE ——夹套阀7、 BUTTERFLY V ALVE ——蝶阀8、 JACKETED FLUSH BOTTOM V ALVE ——夹套底部冲洗阀 9、其它详见PID 图例五、GASKETS （垫片）六、BOLTS （螺栓）七、其它：1、 JACKET SPACER （固定板）2、 JACKET BARRIER （隔板）3、 FLOW CIRCULA TOR （导流板）4、 PR GAGE （压力表）5、 TEMP GAGE （TEMP SCAN ELEMENT/TEMP ELEMENT ）测温元件管外径表。

管件名称中英文对照

缩写中文名称英文名称P管子PipeEL弯头ElbowELL长半径弯头LongradiuselbowELS短半径弯头ShortradiuselbowMEL斜接弯头虾米腰弯头MitreelbowREL异径弯头ReducingelbowT三通TeeLT斜三通LateralteeRT异径三通ReducingteeR异径管接头大小头ReducerCR同心异径管接头同心大小头Concentricreducer ER偏心异径管接头偏心大小头Eccentricreducer CPL管箍CouplingFCPL双头管箍FullcouplingHCPL单头管箍HalfcouplingRCPL异径管箍ReducingcouplingBU内外螺纹接头BushingUN活接头UnionHC软管接头HosecouplerSE翻边短节StubendNIP短节Pipenippleorstraightnipple SNIP异径短节SwagednippleCP管帽封头CapPL管堵丝堵PlugBLK盲板BlankSB8字盲板SpectacleblindblankRP补强板Reinforcingpad法兰缩写中文名称英文名称PLG法兰FlangeWNF对焊法兰WeldingneckflangeSOF平焊法兰Slip-onflangeSWF承插焊法兰Socket-weldingflange T螺纹法兰ThreadedflangeLJ松套法兰Lappedjointflange REDF异径法兰ReducingflangeBF法兰盖日法兰BlindflangeFSF法兰密封面FlangescalingfaceFF全平面FlatfaceRF凸台面RaisedfaceMFF凹凸面MaleａndfemalefaceLF凹面FemalefaceLM凸面MalefaceRJ环连接面RingjointfaceTG榫槽面TongueａndgroovefaceTF榫面TonguefaceGF槽面Grooveface垫片缩写中文名称英文名称G垫片GasketNMG非金属垫片Non-metallicgasketAG石棉垫片AsbestosgasketRG橡胶垫片RubbergasketTEG聚四氟乙烯包复垫片PTFEenvelopegasket SMG半金属垫片SemimetallicgasketMJG金属包垫片Meta-jacketgasketSWG缠绕式垫片SpiralwoundgasketMG金属垫片MetallicgasketFMG金属平垫片FlatmetallicgasketSMSG齿形金属垫片Solidmetalserratedgasket LER透镜式金属环垫LensringgasketOCR八角形金属环垫Octagonalringgasket OVR椭圆形金属环垫OvalringgaksetIR/OR内外定位环InnerringａndouterringIR内定位环InnerringOR外定位环Outerring坚固件缩写中文名称英文名称B螺栓BoltSB螺柱StudboltNU螺母NutTB花蓝螺母TurnbuckleWSR垫圈WasherSWSR弹簧垫圈Springwasher阀门缩写中文名称英文名称GV闸阀GatevalveGLV截止阀GlobevalveCHV止回阀CheckvalveBUV蝶阀ButterflyvalveBAV球阀BallvalvePV旋塞阀PlugvalvecockCV调节阀ControlvalveSV安全阀SafetyvalveRV减压阀Pressurereducingvalve ST蒸汽疏水阀SteamtrapPRV泄压阀Pressurreliefvalve BV呼吸阀BreathervalveNV针形阀NeedlevalveAV角阀DV隔膜阀TWV三通阀SGV插板阀管道上用的小型设备缩写中文名称英文名称SPR气液分离器SeparatorFA阻火器FlamearresterSR过滤器StrainerSRYY型过滤器Y-typestrainer SRTT型过滤器T-typestrainerSRB桶式过滤器Buckettypestrainer TSR临时过滤器Temporarystrainer SIL消声器SilencerSG视镜SlightglassSC取样冷却器SamplecoolerDF排液漏斗DrainfunnelLM管道混合器LinemixerRO限流孔板RestrictionorificeMO混合孔板MixingorificeRD爆破片爆破膜RupturediskEJ补偿器Expansionjoint隔热、伴热中文名称英文名称INS隔热ThermalinsulationH保温HotinsulationC保冷ColdinsulationP防烫伤隔热Personnelprotectioninsulation T&I伴热Tracingａndinsulation管道伴热冷TracingEST蒸汽外伴热ExternalsteamtracingIST蒸汽内伴热InternalsteamtracingSJT蒸汽夹套伴热Steam-jackettracingET电伴热Electrictracing配管材料和等级缩写中文名称英文名称M金属材料MetallicmaterialCS碳钢CarbonsteelCAS铸钢CaststeelFS锻钢ForgedsteelAS合金钢AlloysteelSS不锈钢StainlesssteelAUSTSS奥氏体不锈钢Austeniticstainless-steel CI铸铁CastironMI可锻铸铁MalleableironDI球墨铸铁DuctileironAL铝AluminumBRS黄铜BrassBRZ青铜BronzeCU紫铜CopperLAS低合金钢LowalloysteelFLAS低合金锻钢Forgedlowalloysteel CLAS低合金铸钢Castlowalloysteel THK壁厚ThicknessSCH表号SchedulenumberSTD标准StandardXS加强ExtrastrongXXS特强Doubleextrastrong装置布置缩写中文名称英文名称CN建北ConstructionnorthE东EastW西WestS南SouthN北NorthH水平HorizontalV竖直、铅直、直立VerticalGRD地坪GroundUG地下UndergroundBL装置边界线BatterylimitlineESEW事故沐浴洗眼器Emergencyshowerａndeyewasher HS软管站HosestationML接续分界线MatchlinePS管道支架管架PipingsupportPR管桥PiperackSTRU构架构筑物Structure BLDG建筑物BuildingPD清扫设施Purgedevice PT池PitSHLT棚ShelterCOFF围堰CofferdamFL楼板FloorPF平台Plateform尺寸标注缩写中文名称英文名称EL标高ElevationBOP管底Bottomofpipe COP管中心Centerofpipe TOP管顶TopofpipeFOB底平FlatonbottomFOT顶平FlatontopCL屯中心线CenterlineTL切线TangentlineSYM对称的SymmetricalBOS支架底Bottomofsupport TOS支架顶TopofsupportCL净距净空ClearanceCTC中心至中心Centertocenter CTF中心至面Centertoface CTE中心至端部Centertoend ETE端到端EndtoendFEF法兰端面Flangeａndface FTF面到面FacetofaceD直径DiameterDN公称直径NominaldiameterID内径InsidediameterOD外径OutsidediameterDIM尺寸DimensionMAX最大MaximumMIN最小MinimumAVG平均AverageAPP约、近似Approximate点标高Pointelevation图表缩写中文名称英文名称PFD工艺流程图ProcessflowdiagramPID管道和仪表流程图Piping&instrumentdiagram COD接续图ContinuedondrawingDTL详图DatailSPDWGISODWG管段图Spooldrawingeachlineisometricdrawing DWGNO图号DrawingnumberDWGI所在图号DrawingidentificationLOW材料表ListofmaterialMTO汇料Materialtake-offAPPX附录Appendix.工号JobNumberBEDD基础工程设计数据Basicengineeringdesigndata DEDD详细工程设计数据Detailengineeringdesigndata .修改号RecisionnumberREFDWG参考图ReferencedrawingSC采样接口Sampleconnection操作方式及工作参数缩写中文名称英文名称AUT自动AutomaticML手动Manualcontrol CHOP链条操作Chainoperated CSC铅封关Carsealclose CSO铅封开CarsealopenLC锁闭LockclosedLO锁开LockopenNC正常关NormallycloseNO正常开NormallyopenATM大气压AtmospherePN公称压力Nominalpressure A绝压G表压T温度TemperatureP压力Pressure施工缩写中文名称英文名称W焊接WeldingAW电弧焊ArcweldingGSAW气体保护电弧焊Gasshielded-acrwelding EFW电熔焊ElecricfusionweldingERW电阻焊ElectricResistanceweldingGW气焊GasweldingLW搭接焊LapweldingBW对焊ButtweldingTW定位焊TackweldingSW承插焊SocketweldingCW连续焊ContinuousweldingSEW密封焊SealweldingSFG堆焊SurfacingFW现场焊接FieldweldingHT热处理HeattreatmentPH预热PreheatingSR应力消除StressreliefPWHT焊后热处理PostweldheattreatmentEIT检查、探伤和实验Examination,inspection&testing VE外观检查VisualexaminationUIUT超声探伤UltrasonicinspectiontestRIRT射线探伤RadiographicinspectiontestMPIMT磁粉探伤Magneticparticleinspectiontest LPIPT液体渗透检验Liquidpenterantinspectiontest HADT硬度实验HardnesstestingHYDT水压实验HydraulictestingPNET气压实验Pneumatictesting焊条CoveredelectrodeWW焊丝WeldingwireASSY装配、组合AssemblyF现场FieldF/F现场制造FieldfaricatedSF现场决定SuitinfieldCSP冷紧ColdspringBCT螺栓冷紧BoltcoldtighteningBHY螺栓热紧BolthottighteningCO清洗口CleanoutANNY退火AnnealedPE平端面PlainendBE坡口端BelelledendTHR螺纹ThreadHB布氏硬度BrinnelhardnessRC洛氏硬度其他缩写中文名称英文名称FDN基础FoundationINF信息资料InformationREF 参考ReferenceREV修改RevisionSEQ序号顺序SequenceW/E设备带来WithequipmentW/I仪表带来WithinstrumentCM色标ColourmarkCA 腐蚀裕度CorrosionallowanceUTL公用系统UtilityUC公用工程接头UtilityconnectionQTY数量QuantityWT重量WeightMHR工时ManhourBC螺栓分布圆BoltcircleHP高点HighpointLP低点LowpointSUC吸入口SuctionDIS排出口DischargeSO蒸气吹扫口SteamoutNPT美国标准锥管螺纹NationalstandardtaperpipethreadNPS美国标准直管螺纹NationalstandardstraightpipethreadDR排液DrainVT放气VentRTG 压力等级RatingCL等级ClassSMLS无缝Seamless。

管件中英文对照表 (常用)

碳钢弯头 Carbon Steel Elbow不锈钢弯头 Stainless Steel Elbow高压弯头 High-Pressure Elbow同心异径管 Concentric Reducers偏心异径管 Eccentric Reducers高压异径管 High-pressure Reducers不锈钢等径三通 Stainless Straight Tee碳钢等径三通 Carbon Straight Tee不锈钢等径四通 Stainless Straight Cross高压三通 High-pressure Tee锻制三通 Forged Tee异径接头 Template 管帽 Caps 法兰flange长径和短径弯头 long and short radius elbows同心和偏心异径接头 concentric and eccentric reducers等径和异径三通 straight and reducing outlet tees大小头 CONCENTRIC REDUCER相等的三通Tee Equal等径三通Straight Tee异径三通Reducing Tee等径四通Straight Cross90°短半径弯头90°SS Elbow(SR) U型管Return Bend90°长半径弯头90°SS Elbow (LR)高压厚壁弯头Thickness Elbow盲法兰Blank Flange 弯管Bends翻边stub ends 异径接头reducers 公称通径 nominal diameter外径(mm) outside diameter 中心距至端面的距离center to end理论重量(kg/pcs) approx weight类种description 标准Standard类型Design 材质Material 双丝头 Nipple同心异径短节 SWAGE Nipple活接头 Union PLUG HEX HEAD六角管堵 PLUG HEX HEADSCRD六角螺纹管堵MPT螺纹 RC螺纹螺桩 stud SWAGE (CONC)同心异径短节单承口管箍 Half-Coupling 异径管箍Coupling, Reducing盲板 Blind Flange 带双圈的盲板spectacle blind 偏心的Ecentric 等径直通equal coupling内牙直通 female coupling外牙直通 straight tube with outside90等径弯头 90 equal elbow45等径弯头 45 equal elbow外牙弯头 male elbow内牙弯头 female elbow 等径三通 equal tee异径三通 reducing tee内牙三通female tee外牙三通 male tee 管帽cap拆除:dismantle 结头（管线的）：tie-in插盲板：slip spade 盲板：blank接头：fitting 加热器：heater金属缠绕垫片（带外环）:SW with outside ring 热轧on site: 管汇manifold3. 对焊管座weldolet 对焊支管台nipolet--短管支管台welding plate flange焊接板式法兰..threaded (THD) 螺纹的.sockolet 承插焊支管台...thredolet 螺纹支管台.3. 短节、双丝头 nipple... nipple 螺纹接头短节SWAGE nipple... 活接头 Union4. 螺纹接套；喷嘴nipper 钳子；拔钉钳...nipple 螺纹接套；喷嘴...noiseabatement measure 减低噪音措施• 1. 弯头支管台elbolet|弯头支管台...elbolet|弯头支管台...elbow|弯头2. 螺纹支管台；弯头管座elastometric lining橡胶内衬...elbolet螺纹支管台；弯头管座3. 斜接支管台Sockolet弯头支管台...elbolet斜接支管台trolet镶入式支管嘴Seamless---无缝的equal-----相等的，同样的Reducers----异径的，不同的blind flange--法兰堵板/盲板法兰盲法兰法兰-FLANGEblind--法兰盖,盲目的HEX==hexagon(六角形;六边形)Head--上端;前端头PLUG—管赌NIPOLET—短管斜支管台支管台NIPPLE—螺纹短节PLUG—丝堵SCD NPT--是符合NPT标准的螺纹C.STL A105 TO AP SPEC 4WPI-MWCF01 分开解释如下C.STL A105 材料标准TO AP SPEC 4WPI-MCCN01 应该符合AP（air product）规范4WPI-MCCN01BLE/PSE 大头破口，小头平面SWAGE, CON, BLE/PSE-----异径管短节同心大头破口，小头平面“o-let”=管支台螺纹支管台 threadolet 焊接支管台 weldolet 承插支管台 sockolet弯头支管台 elbolet 斜支管台latrolet 镶入式支管嘴sweeplet 短管支管台npoletPL 平端点，外丝管座承插焊（SWF）BV 斜端点对焊FL 法兰连接法兰连接在AutoCAD Plant 3D 中管道与管道元件连接形式有很多方式，详细介绍如下：端码说明链接示例（匹配）PL 平端点，外丝管座承插焊（SWF）BV 斜端点对焊THDM 外螺纹螺纹连接（THDF）THRD丝扣(THREADED) THDF 内螺纹螺纹连接（THDM）SW 内丝承插焊承插焊FL 法兰连接法兰连接WF 平头平头法兰链接（FL）LAP 搭接环搭接（PL）GRV 凹槽连接凹槽连接（PL）SO 松套平焊（PL）PPL 塑料平面熔焊PSW 内丝塑料管座胶接（PPL）LFL 直法兰LLP 直搭接LUG 接线片法兰连接（FL）BELL 钟形接头钟形接头和承插焊（SPIG）SPIG 承插焊钟形接头和承插焊（BELL）TAP 旋塞旋塞（PL）异径双承口管箍—reducing couplingCoupling, RED—异径双承口管箍FPT（缩写）=Female Pipe Thread=内螺纹管接头lateral tee--斜三通；斜侧三通FORGED--锻造inside THR-Ends—底端内侧螺纹LO TEMP=low temperature 低温。

管子及管件部分中英文对照

管子及管件部分中英文对照1 管道组成件Piping component1.1 管子PipeBE（BEVELLED ENDS）坡口Caps 管帽DRL 双倍尺SRL 单倍尺ERW:电阻焊SAW埋弧焊SSAW 螺旋埋弧焊LSAW 直缝埋弧焊SMLS 无缝管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded（ERW）steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe 螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbowk半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand)双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand)异径三通（分支口为异径）reducing tee (reducing on outlet)异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet)异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull head)45°斜三通45° lateral45°斜三通（支管为异径）45° lateral (reducing on branch)45°斜三通(一个直通口为异径) 45° lateral (reducing on one run)45°斜三通(一个直通口及支管为异径) 45° lateral (reducing on one run and branch)Y型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and outlet)异径四通（两个分支口为异径）reducing cross (reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run and both outlet) 异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss管接头coupling, full coupling半管接头half coupling异径管接头reducing coupling活接头union内外螺纹缩接（俗称补芯）bushing管帽cap (C)堵头plug短节nipple异径短节reducing nipple; swage nipple1.3 弯管Bend预制弯管fabricated pipe bend跨越弯管（^ 形）cross-over bend偏置弯管（~ 形）offset bend90°弯管quarter bend环形弯管cirele bend单侧偏置90°弯管（? 形）single offset quarter bendS形弯管“S” bend单侧偏置U形膨胀弯管（| ?形）single offset “U” bend U形弯管“U” b end双偏置U膨胀弯管double offset expansion “U” bend。

管件中英文对照表-(常用)

碳钢弯头 Carbon Steel Elbow不锈钢弯头 Stainless Steel Elbow高压弯头 High-Pressure Elbow同心异径管 Concentric Reducers偏心异径管 Eccentric Reducers高压异径管 High-pressure Reducers不锈钢等径三通 Stainless Straight Tee碳钢等径三通 Carbon Straight Tee不锈钢等径四通 Stainless Straight Cross高压三通 High-pressure Tee锻制三通 Forged Tee异径接头 Template 管帽 Caps 法兰flange长径和短径弯头 long and short radius elbows同心和偏心异径接头 concentric and eccentric reducers等径和异径三通 straight and reducing outlet tees大小头 CONCENTRIC REDUCER相等的三通Tee Equal等径三通Straight Tee异径三通Reducing Tee等径四通Straight Cross90°短半径弯头90°SS Elbow(SR) U型管Return Bend90°长半径弯头90°SS Elbow (LR)高压厚壁弯头Thickness Elbow盲法兰Blank Flange 弯管Bends翻边stub ends 异径接头reducers 公称通径 nominal diameter外径(mm) outside diameter 中心距至端面的距离center to end理论重量(kg/pcs) approx weight类种description 标准Standard类型Design 材质Material 双丝头 Nipple同心异径短节 SWAGE Nipple活接头 Union PLUG HEX HEAD六角管堵 PLUG HEX HEADSCRD六角螺纹管堵MPT螺纹 RC螺纹螺桩 stud SWAGE (CONC)同心异径短节单承口管箍 Half-Coupling 异径管箍Coupling, Reducing盲板 Blind Flange 带双圈的盲板spectacle blind 偏心的Ecentric 等径直通equal coupling内牙直通 female coupling外牙直通 straight tube with outside90等径弯头 90 equal elbow45等径弯头 45 equal elbow外牙弯头 male elbow内牙弯头 female elbow 等径三通 equal tee异径三通 reducing tee内牙三通female tee外牙三通 male tee 管帽cap拆除:dismantle 结头〔管线的〕：tie-in插盲板：slip spade 盲板：blank接头：fitting 加热器：heater金属缠绕垫片〔带外环〕:SW with outside ring 热轧on site: 管汇manifold3. 对焊管座weldolet 对焊支管台nipolet--短管支管台welding plate flange焊接板式法兰..threaded (THD) 螺纹的.sockolet 承插焊支管台...thredolet 螺纹支管台.3. 短节、双丝头 nipple... nipple 螺纹接头短节SWAGE nipple... 活接头 Union4. 螺纹接套；喷嘴nipper 钳子；拔钉钳...nipple 螺纹接套；喷嘴...noiseabatement measure 减低噪音措施• 1. 弯头支管台elbolet|弯头支管台...elbolet|弯头支管台...elbow|弯头2. 螺纹支管台；弯头管座elastometric lining橡胶内衬...elbolet螺纹支管台；弯头管座3. 斜接支管台Sockolet弯头支管台...elbolet斜接支管台trolet镶入式支管嘴Seamless---无缝的equal-----相等的，同样的Reducers----异径的，不同的blind flange--法兰堵板/盲板法兰盲法兰法兰-FLANGEblind--法兰盖,盲目的HEX==hexagon(六角形;六边形)Head--上端;前端头PLUG—管赌NIPOLET—短管斜支管台支管台NIPPLE—螺纹短节PLUG—丝堵SCD NPT--是符合NPT标准的螺纹C.STL A105 TO AP SPEC 4WPI-MWCF01 分开解释如下C.STL A105 材料标准TO AP SPEC 4WPI-MCCN01 应该符合AP〔air product〕标准4WPI-MCCN01BLE/PSE 大头破口，小头平面SWAGE, CON, BLE/PSE-----异径管短节同心大头破口，小头平面“o-let”=管支台螺纹支管台 threadolet 焊接支管台 weldolet 承插支管台 sockolet弯头支管台 elbolet 斜支管台latrolet 镶入式支管嘴sweeplet 短管支管台npoletPL 平端点，外丝管座承插焊〔SWF〕BV 斜端点对焊FL 法兰连接法兰连接在AutoCAD Plant 3D 中管道与管道元件连接形式有很多方式，详细介绍如下：端码说明链接例如〔匹配〕PL 平端点，外丝管座承插焊〔SWF〕BV 斜端点对焊THDM 外螺纹螺纹连接〔THDF〕THRD丝扣(THREADED) THDF 内螺纹螺纹连接〔THDM〕SW 内丝承插焊承插焊FL 法兰连接法兰连接WF 平头平头法兰链接〔FL〕LAP 搭接环搭接〔PL〕GRV 凹槽连接凹槽连接〔PL〕SO 松套平焊〔PL〕PPL 塑料平面熔焊PSW 内丝塑料管座胶接〔PPL〕LFL 直法兰LLP 直搭接LUG 接线片法兰连接〔FL〕BELL 钟形接头钟形接头和承插焊〔SPIG〕SPIG 承插焊钟形接头和承插焊〔BELL〕TAP 旋塞旋塞〔PL〕异径双承口管箍—reducing couplingCoupling, RED—异径双承口管箍FPT〔缩写〕=Female Pipe Thread=内螺纹管接头lateral tee--斜三通；斜侧三通FORGED--锻造inside THR-Ends—底端内侧螺纹LO TEMP=low temperature 低温。

常用管件管道配件中英文对照

常用管件管道配件中英文对照１.管件系列1.1>>P 管子Pipe1.2>> EL 弯头Elbow1.2.1> ELL 长半径弯头Long radius elbow1.2.2> ELS 短半径弯头Short radius elbow1.2.3>MEL 斜接弯头（虾米腰弯头）Mitre elbow1.2.4> REL 异径弯头Reducing elbow1.3>> T 三通Tee1.3.1> LT 斜三通Lateral tee1.3.2> RT 异径三通Reducing tee1.3.3> CROSS 四通1.4>>R 异径管接头（大小头）Reducer1.4.1> CR 同心异径管接头（同心大小头）Concentric reducer 1.4.2> ER 偏心异径管接头（偏心大小头）Eccentric reducer 1.5>> CPL 管箍Coupling1.5.1> FCPL 双头管箍Full coupling1.5.2> HCPL 单头管箍Half coupling1.5.3> RCPL 异径管箍Reducing coupling1.6>>BU 内外螺纹接头Bushing1.7>> UN 活接头Union1.8>> HC 软管接头Hose coupler1.9>> SE 翻边短节Stub end1.10>> NIP 短节Pipe nipple or straight nipple1.10.1>SNIP 异径短节Swaged nipple1.11>>CP 管帽（封头）Cap1.12>> PL 管堵（丝堵）Plug1.13>> BLK 盲板Blank1.13.1> SB 8字盲板Spectacle blind1.14>> PAD 补强板Reinforcing pad1.15>焊接支管台 WELDOLET1.16> 螺纹支管台 THREADOLET1.17> FO 限流孔板2 法兰2.1>> PLG 法兰Flange2.1.1> WNF 对焊法兰Welding neck flange2.1.2> SOF 平焊法兰Slip-on flange2.1.3> SWF 承插焊法兰Socket-welding flange2.1.4>T 螺纹法兰Threaded flange2.1.5> LJ 松套法兰Lapped joint flange2.1.6> REDF 异径法兰Reducing flange2.1.7> BF 法兰盖（盲法兰）Blind flange2.2>> FSF 法兰密封面Flange scaling face2.2.1> FF 全平面Flat face2.2.2>RF 凸台面Raised face2.2.3> MFF 凹凸面Male and female face2.2.4>LF 凹面Female face2.2.5> LM 凸面Male face2.2.6> RJ 环连接面Ring joint face2.2.7>TG 榫槽面Tongue and groove face2.2.8> TF 榫面Tongue face2.2.9> GF 槽面Groove face3 垫片3.1>> >G 垫片Gasket3.1.1>> NMG 非金属垫片Non-metallic gasket3.1.1.1> AG 石棉垫片Asbestos gasket3.1.1.2> RG 橡胶垫片Rubber gasket3.1.1.3> TEG 聚四氟乙烯包复垫片PTFE envelope gasket 3.1.2>> SMG 半金属垫片Semimetallic gasket3.1.2.1 >MJG 金属包垫片Meta-jacket gasket3.1.2.2> SWG 缠绕式垫片Spiral wound gasket3.1.3>> MG 金属垫片Metallic gasket3.1.3.1> FMG 金属平垫片Flat metallic gasket3.1.3.2> SMSG 齿形金属垫片Solid metal serrated gasket 3.1.3.3> LER 透镜式金属环垫Lens ring gasket3.1.3.4> OCR 八角形金属环垫Octagonal ring gasket3.1.3.5> OVR 椭圆形金属环垫Oval ring gakset3.1.3.6> IR/OR 内外定位环Inner ring and outer ring 3.1.3.7> IR 内定位环Inner ring3.1.3.8> OR 外定位环Outer ring4 坚固件4.1>> B 螺栓Bolt4.1.1> SB 螺柱Stud bolt4.2>> NU 螺母Nut4.3>> TB 花蓝螺母Turnbuckle4.4>> WSR 垫圈Washer4.4.1 >SWSR 弹簧垫圈Spring washer5 阀门5.1>> GV 闸阀Gate valve5.2>> GLV 截止阀Globe valve5.3>> CHV 止回阀Check valve5.4 >> BUV 蝶阀Butterfly valve5.5>> BAV 球阀Ball valve5.6>> PV 旋塞阀Plug valve (cock)5.7>> CV 调节阀Control valve5.8>> SV 安全阀Safety valve5.9>>RV 减压阀Pressure reducing valve 5.10>> ST 蒸汽疏水阀Steam trap5.11>> PRV 泄压阀Pressur relief valve5.12>> BV 呼吸阀Breather valve5.13>> NV 针形阀Needle valve5.14>> AV 角阀5.15>> DV 隔膜阀5.16>> TWV 三通阀5.17>> SGV 插板阀6 管道上用的小型设备6.1>> SPR 气液分离器Separator6.2 >>FA 阻火器Flame arrester6.3 >>SR 过滤器Strainer6.3.1> SRY Y型过滤器Y-type strainer6.3.2> SRT T型过滤器T-type strainer6.3.3> SRB 桶式过滤器Bucket type strainer 6.3.4> TSR 临时过滤器Temporary strainer 6.4.>> SIL 消声器Silencer6.5 >>SG 视镜Slight glass6.6 >>SC 取样冷却器Sample cooler6.7 >>DF 排液漏斗Drain funnel6.8>> LM 管道混合器Line mixer6.9>> RO 限流孔板Restriction orifice6.9.1> MO 混合孔板Mixing orifice6.1>>> RD 爆破片（爆破膜）Rupture disk6.11 >>EJ 补偿器Expansion joint7 隔热、伴热编号缩写中文名称英文名称7.1 >>INS 隔热Thermal insulation7.1.1> H 保温Hot insulation7.1.2> C 保冷Cold insulation7.1.3>> P 防烫伤隔热Personnel protection insulation7.2 >T&I 伴热Tracing and insulation7.3> T 管道伴热（冷）Tracing7.3.1> EST 蒸汽外伴热External steam tracing7.3.2> IST 蒸汽内伴热Internal steam tracing7.3.3 >SJT 蒸汽夹套伴热Steam-jacket tracing7.3.4 >ET 电伴热Electric tracing8、配管材料和等级8.1> M 金属材料Metallic material8.1.1> CS 碳钢Carbon steel8.1.2 >CAS 铸钢Cast steel8.1.3> FS 锻钢Forged steel8.1.4>> AS 合金钢Alloy steel8.1.5> SS 不锈钢Stainless steel8.1.6> AUST SS 奥氏体不锈钢Austenitic stainless-steel 8.1.7>> CI 铸铁Cast iron8.1.8> MI 可锻铸铁Malleable iron8.1.9> DI 球墨铸铁Ductile iron8.1.10> AL 铝Aluminum8.1.11> BRS 黄铜Brass8.1.12> BRZ 青铜Bronze8.1.13> CU 紫铜Copper8.1.14> LAS 低合金钢Low alloy steel8.1.15> FLAS 低合金锻钢Forged low alloy steel8.1.16> CLAS 低合金铸钢Cast low alloy steel8.2>> THK 壁厚Thickness8.2.1> SCH 表号Schedule number8.2.2> STD 标准Standard8.2.3 >>XS 加强Extra strong8.2.4>> XXS 特强Double extra strong9、装置布置9.1>> CN 建北Construction north9.2 >>E 东East9.3>> W 西West9.4>> S 南South9.5>> N 北North9.6>> H 水平Horizontal9.7>> V 竖直、铅直、直立Vertical9.8>> GRD 地坪Ground9.9>> UG 地下Underground9.10>> BL 装置边界线Battery limit line9.11>> ESEW 事故沐浴洗眼器Emergency shower and eye washer 9.12>> HS 软管站Hose station9.13 >>ML 接续分界线Match line9.14>> PS 管道支架（管架）Piping support9.15>> PR 管桥Pipe rack9.16>>STRU 构架（构筑物）Structure9.17>>BLDG 建筑物Building9.18>> PD 清扫设施Purge device9.19 >>PT 池Pit9.20 >>SHLT 棚Shelter9.21>> COFF 围堰Cofferdam9.22>> FL 楼板Floor9.23>> PF 平台Plateform10、尺寸标注10.1 >>>EL 标高Elevation10.2>> BOP 管底Bottom of pipe10.3>> COP 管中心Center of pipe10.4>> TOP 管顶Top of pipe10.5 >>FOB 底平Flat on bottom10.6>> FOT 顶平Flat on top10.7>> CL(屯) 中心线Center line10.8>> TL 切线Tangent line10.9>> SYM 对称的Symmetrical10.10>> BOS 支架底Bottom of support10.11 >>TOS 支架顶Top of support10.12>> CL 净距（净空）Clearance10.13>> CTC 中心至中心Center to center10.14>> CTF 中心至面Center to face10.15>> CTE 中心至端部Center to end10.16>> ETE 端到端End to end10.17>> FEF 法兰端面Flange and face10.18 >>FTF 面到面Face to face10.19 >>D 直径Diameter10.20>> DN 公称直径Nominal diameter10.21 >>ID 内径Inside diameter10.22>> OD 外径Outside diameter10.23>> DIM 尺寸Dimension10.24>> MAX 最大Maximum10.25 >>MIN 最小Minimum10.26>> AVG 平均Average10.27>> APP 约、近似Approximate10.28>> PT.EL 点标高Point elevation11 图表11.1>> PFD 工艺流程图Process flow diagram11.2>> PID 管道和仪表流程图Piping & instrument diagram11.3>> COD 接续图Continued on drawing11.4>> DTL 详图Datail11.5>> SPDWG 管段图Spool drawing (each line isometric drawing) 11.6>> DWGNO 图号Drawing number11.7>> DWGI 所在图号Drawing identification11.8>> LOW 材料表List of material11.9>> MTO 汇料Material take-off11.10>> APPX 附录Appendix11.11>> JOB. No. 工号Job Number11.12>> BEDD 基础工程设计数据Basic engineering design data 11.13>> DEDD 详细工程设计数据Detail engineering design data 11.14>> REV. No. 修改号Recision number11.15>> REF DWG 参考图Reference drawing11.16 >>SC 采样接口Sample connection12、操作方式及工作参数12.1>> AUT 自动Automatic12.2>> ML 手动Manual control12.3>> CHOP 链条操作Chain operated12.4 >>CSC 铅封关Car seal close12.5>> CSO 铅封开Car seal open12.6>> LC 锁闭Lock closed12.7>> LO 锁开Lock open12.8>> NC 正常关Normally close12.9>> NO 正常开Normally open12.10>> ATM 大气压Atmosphere12.11>> PN 公称压力Nominal pressure12.12>> A 绝压12.13>> G 表压12.14>> (T) 温度Temperature12.15>> (P) 压力Pressure13、施工13.1>> W 焊接Welding13.1.1> AW(SMAW) 电弧焊Arc welding13.1.2> GSAW 气体保护电弧焊Gas shielded-acr welding13.1.3> EFW 电熔焊Elecric fusion welding13.1.4 >ERW 电阻焊Electric Resistance welding13.1.5> GW 气焊Gas welding13.1.6> LW 搭接焊Lap welding13.1.7> BW 对焊Butt welding13.1.8 >TW 定位焊Tack welding13.1.9> SW 承插焊Socket welding13.1.10> CW 连续焊Continuous welding13.1.11> SEW 密封焊Seal welding13.1.12> SFG 堆焊Surfacing13.1.13> FW 现场焊接Field welding13.1.14 > TIG(GTAW) 钨极惰性气体保护焊(氩弧焊)Gas Tungsten Arc Weld 13.2 >>HT 热处理Heat treatment13.2.1>> PH 预热Preheating13.2.2 >SR 应力消除Stress relief13.2.3> PWHT 焊后热处理Post weld heat treatment13.3> EIT 检查、探伤和实验Examination, inspection & testing13.3.1> VE 外观检查Visual examination13.3.2>> UI (UT) 超声探伤Ultrasonic inspection (test)13.3.3>> RI (RT) 射线探伤Radiographic inspection (test)13.3.4> MPI (MT) 磁粉探伤Magnetic particle inspection (test) 13.3.5> LPI (PT) 液体渗透检验Liquid penterant inspection (test) 13.3.6> HADT 硬度实验Hardness testing13.3.7> HYDT 水压实验Hydraulic testing13.3.8> PNET 气压实验Pneumatic testing13.3.9> CE 焊条Covered electrode13.3.10> WW 焊丝Welding wire13.3.11> ASSY 装配、组合Assembly13.3.12 >F 现场Field13.3.13> F/F 现场制造Field faricated13.3.14> SF 现场决定Suit in field13.3.15> CSP 冷紧Cold spring13.3.16> BCT 螺栓冷紧Bolt cold tightening13.3.17> BHY 螺栓热紧Bolt hot tightening13.3.18> CO 清洗口Clean out13.3.19> ANNY 退火Annealed13.4 >PE 平端面Plain end13.5 >BE 坡口端Belelled end13.6> THR 螺纹Thread13.7 >HB 布氏硬度Brinnel hardness13.8> RC 洛氏硬度14、其他14.1> FDN 基础Foundation14.2> INF 信息（资料）Information14.3 >REF 参考Reference14.4 >REV 修改Revision14.5 >SEQ 序号（顺序）Sequence14.6> W/E 设备带来With equipment14.7> W/I 仪表带来With instrument14.8> CM 色标Colour mark14.9> CA 腐蚀裕度Corrosion allowance14.10> UTL 公用系统Utility14.11> UC 公用工程接头Utility connection14.12> QTY 数量Quantity14.13 >WT 重量Weight14.14> MHR 工时Man hour14.15> BC 螺栓分布圆Bolt circle14.16> HP 高点High point14.17> LP 低点Low point14.18> SUC 吸入（口）Suction14.19 DIS 排出（口）Discharge14.20> SO 蒸气吹扫（口）Steam out14.21> NPT 美国标准锥管螺纹National standard taper pipe thread 14.22> NPS 美国标准直管螺纹National standard straight pipe thread 14.23> DR 排液Drain14.24> VT 放气Vent14.25> RTG （压力）等级Rating14.26> CL 等级Class14.27 >SMLS 无缝Seamless14.28> 螺旋缝 Spiral seam。

管件名称中英文对照

管件名称中英文对照
缩写中文名称英文名称P管子PipeEL弯头ElbowELL长半径弯头LongradiuselbowELS短半径弯头ShortradiuselbowMEL斜接弯头（虾米腰弯头）MitreelbowREL异径弯头ReducingelbowT三通TeeLT斜三通LateralteeRT异径三通ReducingteeR异径管接头（大小头）ReducerCR同心异径管接头（同心大小头）ConcentricreducerER偏心异径管接头（偏心大小头）EccentricreducerCPL管箍CouplingFCPL双头管箍FullcouplingHCPL单头管箍HalfcouplingRCPL异径管箍ReducingcouplingBU内外螺纹接头BushingUN活接头UnionHC软管接头HosecouplerSE翻边短节StubendNIP短节PipenippleorstraightnippleSNIP异径短节SwagednippleCP管帽（封头）CapPL管堵（丝堵）PlugBLK盲板BlankSB8字盲板Spectacleblind（blank）RP补强板Reinforcingpad法兰缩写中文名称英文名称PLG法兰FlangeWNF对焊法兰WeldingneckflangeSOF平焊法兰Slip-onflangeSWF承插焊法兰Socket-weldingflangeT螺纹法兰ThreadedflangeLJ松套法兰LappedjointflangeREDF异径法兰ReducingflangeBF法兰盖（日法兰）BlindflangeFSF法兰密封面FlangescalingfaceFF全平面FlatfaceRF凸台面RaisedfaceMFF凹凸面MaleａndfemalefaceLF凹面FemalefaceLM凸面MalefaceRJ环连接面Ringjoint

管件资料中英文对照

管件资料中英文对照
等径直通equal coupling
异径直通reducing coupling
内牙直通 female coupling
外牙直通 straight tube with outside
90等径弯头 90 equal elbow
45等径弯头 45 equal elbow
等径四通 Straight Cross
水管连接件
外接头俗称：直接头、直通、束节、管箍。用途：用来连接两根公称通径相同的管子
异径外接头俗称：异径管箍、大小头，用来连接两根公称通径不同的管子，使管路通径变小。
活接头俗称：连接螺母、外丝活节，主要用于两根固定管中间的连接。
六角内接头俗称：对丝、外丝。用来连接两根公称通径相同的内螺纹管件或阀门
内外螺母俗称：补心、管子衬。外螺纹一端配合外接俗称：90度弯头，用来连接两根公称通径相同的管子，使管路作90度转弯和通径变小；一般可分为等径弯头和异径弯头、带丝活节和不带外丝活节
异径接头俗称：大小头，用来连接两根规格不同的管材或管件。
碳钢等径三通 Carbon Straight Tee
不锈钢等径四通 Stainless Straight Cross
高压三通 High-pressure Tee
锻制三通 Forged Tee
异径接头 Template
管帽 Caps
法兰flange
长径和短径弯头 long and short radius elbows
管帽
俗称：盖头、管盖、用来封闭管路，作用与管堵相同，但管帽可直接旋在管子上，不需要与其它管件配合。
45度弯头俗称：半弯，用来连接两根直径相同的管子，使管路成45度转弯。

管道及配件中英文对照

管道及配件中英文对照化工管道词汇翻译1 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbow长半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand) 双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand)异径三通（分支口为异径）reducing tee (reducing on outlet)异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet)异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull head) 45°斜三通45° lateral管道及配件中英文对照245°斜三通（支管为异径）45° lateral (reducing on branch)45°斜三通(一个直通口为异径) 45° lateral (reducing on one run)45°斜三通(一个直通口及支管为异径) 45° lateral (reducing on one run and branch)Y型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and outlet)异径四通（两个分支口为异径）reducing cross (reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run and both outlet)异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss(以上带红线的单词已经查过，应该是行业很组合的名词，可以查得到)。

管件英汉对照词大全

管件英汉对照词大全2010-06-28 09:45管件 pipe fitting对焊管件 butt welding fittings碳钢对焊管件 carbon steel butt welding fittings不锈钢对焊管件 stainless steel butt welding fittings 弯头 elbow异径弯头 reducing elbow碳钢弯头 Carbon Steel Elbow不锈钢弯头 Stainless Steel Elbow高压弯头 High-Pressure Elbow等径三通 Straight Tee异径三通 Reducing Tee碳钢三通 CS Tee同心异径管 Concentric Recducer偏心异径管 eccentric reducer高压异径管 high-pressure reducer不锈钢管帽 stainless steel caps碳钢管帽 carbon steel caps四通 cross单承口管箍 half coupling双承口管箍 coupling半管接头 boss对焊管座 weldolets承插管座 sockolets螺纹管座 threadolets变径接头 welding insert补心\内外丝、螺套 bushing六角头螺套 hex head bushing平螺套 flush bushing管接头 coupler活接头、游任 union短接头、对丝 nipple六角对丝 hex nipple螺母 nut管堵、螺塞 plug六角头螺塞 hex head plug四方头螺塞 square head plug圆头螺塞 round head plug套筒 sleeve弯管 bendU型管 close return bend法兰 flange锻钢法兰 forged steel flanges对焊法兰 welding neck flanges平焊法兰 slip on flanges盲板法兰 blind flanges平板法兰 plate flanges承插焊法兰 socket welding flanges螺纹法兰 threaded flanges松套法兰 lap joint flanges翻边短节 stub ends公称通径 Nomonal Diameter端部外径 Outside Diameter at Bevel中心至端面 Center to End中心至中心 Center to Center背面到端面 Back to FaceNPT=Normal Pressure and Temperature 常温常压, 标准温度与压力90°短半径弯头90°SS Elbow (SR)90°长半径弯头90°SS Elbow (LR)高压厚壁弯头 Thickness ElbowTee Equal 相等的三通male plug 插头female socket 插座dust cap 防尘盖等径三通 Straight teesafety cap 安全罩异径三通 Reducing Tee等径四通 Straight Cross同心异径管 Concentric Reducers同中心的 concentric不同圆心的 eccentric偏心异径管 Eccentric Reducers高压异径管 High-pressure Reducers不锈钢等径三通 Stainless Straight Tee碳钢等径三通 Carbon Straight Tee不锈钢等径四通 Stainless Straight Cross高压三通 High-pressure Tee锻制三通 Forged Tee异径接头 Template管帽 Caps法兰 flangevalve 阀门类型description 类种Standard 标准Design 类型Type 类型Type Model 型号Material 材质classes 种类specification 规格机床类冲床punching machine机械手robot油压机hydraulic machine车床 lathe刨床planer铣床miller磨床grinder（钻床）driller线切割linear cutting金属切削 metal cutting机床 machine tool管件材质类steel 钢carbon steel 碳素钢rustless steel 不锈钢alloy steel 合金钢angle steel 角钢blister steel 泡钢carburizing steel 渗碳钢cast steel 铸钢cementation steel 渗碳钢chrome steel 铬钢chrome molybdenum steel 铬钼钢chrome-vanadium steel 铬钒钢dies steel 模具钢ferrite steel 铁素体钢ferritic steel 铁素体钢flat steel 扁钢flat-rolled steel 扁钢forged steel 锻造钢hard steel 硬钢hardened stainless steel 硬化不锈钢heat (-resisting) steel 耐热钢hig-carbon steel 高碳钢high manganese steel 高锰钢high-speed steel 高速钢；锋钢high strength steel 高强度钢high tensile steel 高强度钢H-section steel 工字钢low carbon steel 低碳钢low manganese steel 低锰钢mild steel 软钢nickel steel 镍钢nickel-chrome steel 镍铬钢nickel chromium steel 镍铬钢The Tube Inserting （卡套式接头）Compressioned Joint （管路截止阀）Welding Joint （焊接式接头）Velding Joint （扩口式接头）Ream Joint （控油压接头）Pipeline Cut-off Valves （紫铜管件）Fast Fittings （管夹）Oil-Pressure Controlling Connectors （快速接头）Pagoda-Shape Connectors （宝塔型接头）Hydraulic Rubber Tube Assembly （液压胶管总成）Flange （法兰）Inside-and-Outside Connectors （内外接头）Construction Machinery Connectors （工程机械接头）Connectors for Military Use （军用接头）长径和短径弯头 long and short radius elbows同心和偏心异径接头 concentric and eccentric reducers 等径和异径三通 straight and reducing outlet tees大小头 CONCENTRIC REDUCERU型管Return Bend盲法兰Blank Flange弯管Bends翻边stub ends异径接头reducers公称通径 nominal diameter外径(mm) outside diameter中心距至端面的距离 center to end理论重量(kg/pcs) approx weight双丝头 Nipple短节 SWAGE NIPPLE内外螺纹活接头 Union螺桩 studHalf-Coupling单承口管箍Coupling双承口管箍盲板 Blind Flangespectacle blind 带双圈的盲板Ecentric 偏心的活接活接 loose joint活接地 swinging earth活接结合 articulated joint活接联接器 joint coupling活接三通 union tee活接头 articulation; union swivel; union活接头螺母 union nut活接头螺栓 swing bolt活接头套管 union thimble活接卸槽 articulated chute (浇混凝土用的)弯头 joint弯头 angle fittings; bent pipe; elbow; knee弯头扳手 bent-handle wrench; bent spanner弯头车刀 angular tool弯头持针钳 curved needle holders弯头刀架 knee tool弯头道钉 brob弯头管 swan neck弯头键 gib head key弯头接合 knee-joint弯头螺栓 bolt with one end bent back弯头锁紧螺母 elbow jam unt弯头套管 elbow union弯头套筒扳手 offset socket wrench弯头脱水器 elbow separator弯头芯盒 elbow core box三通三通 tee bend; tee branch; tee joint; tee conneetion; tee fitting; wye; Y; yoke 三通玻璃栓 three-way glass stopcock三通道放大器 three-channel amplifier; three-path amplifier三通道自动驾驶仪 three-dimensional autopilot三通电缆分线盒 three-way coupling box三通阀 tee valve; three-port valve; three-way valve; triple valve三通阀盖 triple-valve cap三通阀活塞 triple-valve piston三通阀联箱 three way valve menifold三通阀体 triple body; triple-valve body三通管 single sweep tee; T-branch (pipe); three-limb tube三通管接头 tee pipe coupling三通横长 horizontal length of tee三通换向旋塞 three-way reversing cock三通活栓 three-way cock三通货协定 triparties currency agreement三通接头 tee coupling; tee fitting; tee union; three-way piece; three-way connection三通接线夹 three-way connector三通开关 three-way cock三通控制阀 three-way control valve三通连接 tee junction三通路循环器 three-terminal circulator三通式热风炉 three-pass stove三通天线转发开关 triplexer三通筒 triple cylinder三通筒垫密片 triple-cylinder gasket三通弯头 three-way elbow三通旋塞 tee cock; three-way cock; three-throw tap三通循环器 three-terminal circulator三通液体流量计 tee fluid flow meter三通闸阀 treble ported slide valve直通直通 direct connection; straight in; straight bore; through; feed(-)through; once-through 直通拨号 through dial(l)ing直通测量线路 end-to-end measurement直通单向阀 in-line check valve; straight check valve; straightway check valve直通道路 through road直通的 through and through直通地 dead earth; dead ground直通垫外底 through midsole直通电报 telex直通电报通信 telex communication直通电流 through current直通电流偏置 through current bias直通电路 direct circuit直通阀 pass valve; straight-through valve; straightway valve; through valve直通干馏炉 through retort直通锅炉 once-through boiler直通换料 once-through refuelling直通回路 straight circuit直通汇接呼叫制 straight forwardjunction working直通监控 through supervision直通接头 straight coupling; straight fitting直通接线装置 through joint直通街道 through expressway; through street; throughway直通进位 standing carry直通开关 globe cock直通空气制动阀 straight air brake valve直通空气制动器 straight air brake直通快动阀 straight-through fast acting valve直通连接 straight-through joint直通裂化 straight-through cracking直通流动 straight through flowpiping material specification。

管子及管件部分中英文对照

管子及管件部分中英文对照管子PipeCaps 管帽SAW埋弧焊管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe [kɑ:st ˈaiən paip]碳钢管carbon steel pipe合金钢管alloy steel pipe ['ælɔɪ]不锈钢管stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe [ˌɔ:stə'nɪtɪk] 轧制钢管wrought-steel pipe [rɔ:t]锻铁管wrought-iron pipe无缝钢管seamless steel pipe焊接钢管welded steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe直管run pipe; straight pipe管件Fitting弯头elbow异径弯头reducing elbow长半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return三通tee异径三通reducing tee等径三通straight tee45°斜三通45°lateral四通cross等径四通straight cross异径四通reducing cross异径管reducer同心异径管concentric reducer [kənˈsentrɪk] 偏心异径管eccentric reducer [ɪkˈsentrɪk] 螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet短节nipple ['nɪpl]异径短节reducing nipple; swage nipple弯管Bend90°弯管quarter bend [bend]Current 电流Inert gas 惰性气体Polarity 极性Filler metal 填充金属Base metal 母材Welding process 焊接方法Qualification 评定Pipe bend specimen 管子弯曲试样bend test 弯曲试验Welding supervised 焊接监督者Defects 缺陷Specification 标准Autual values 实际值Range qualified 评定范围法兰flangeU型管Return Bend翻边stub endsGeneral manager 总经理Representative 代表Attachment 附件承插焊法兰socket welding flange带颈对焊法兰welding neck flange对焊环welding neck collar平焊环welding-on collar整体管法兰integral pipe flange钢管法兰steel pipe flange螺纹法兰threaded flange滑套法兰（包括平焊法兰）slip-on flange (SO); slip-on welding flange 松套法兰lap joint flange (LJF)法兰盖blind flange, blind孔板法兰orifice flange异径法兰reducing flange盘座式法兰pad type flange松套带颈法兰loose hubbed flange焊接板式法兰welding plate flange突缘短节stub end, lap翻边端lapped pipe end松套板式法兰loose plate flange压力级pressure rating, pressure rating class压力—温度等级pressure-temperature rating法兰密封面，法兰面flange facing突面raised face (RF)凸面male face (MF)凹面female face (FMF)榫面tongue face槽面groove face环连接面ring joint face全平面；满平面flat face; full face (FF)光滑突面smooth raised face (SRF)法兰面加工facing finish粗糙度roughness光滑的smooth齿形serrated均方根root mean square (RMS)算术平均粗糙高度arithmetical average roughness height (AARH) 配对法兰companion-flange螺栓圆bolt circle (B.C.)。

钢管及管件中英文对照

钢管及管件中英文对照90°ELBOW,BW,20#,SMLS,LR,GB/T8163,SH/T3408,GrⅠ,Sch4090度弯头，对焊，20#碳钢材质，无缝，制造标准GB/T8163 ，验收标准SH/T3408，质量等级1级，SCH40是ASME壁厚表示方式三通1 1/2"*3/4" SW SCH80 20 GB/T14383(I)是什么意思异径三通 1 1/2"*3/4" SW(承插焊) SCH80(厚度，查询可得知具体厚度) 20（材质，20#碳钢）GB/T14383(I)（标准号）90 ELBOW 20# GALV SMLS GB/T8163,LR BW:SH3408 SCH80 其中GALV和LR 代表什么意思？" SWAGE NIPPLE 20# GB8163 PBE:MSS SP-95 SCH80 中PBE:MSS SP-95 是什么意思？SPIRAL WOUND GASKET CL150 RF ,4.5MM, 304+GRAF ,344 INNERRING,CS OUT RING: SH3407 其中红颜色的字母代表什么意思？20＃GB/T699 SW 平底形40T025/01 SCH160 中的红颜色的字母代表什么意思？螺柱/螺母STUD BOLT WITH 2 HEAVY NUTS,35CRMOA/35CRMOA,SH3404 其中红颜色的字母代表什么意思？以上表示的字母可以在哪里查到啊GALV英文为galvanized是镀锌的意思，一般是仪表风管线和水管线。

LR英文为long radius是长半径弯头的意思。

4.5MM, 304+GRAF ,344 INNERRING,CS OUT RING，表示垫片厚度为4.5mm，304不锈钢＋石墨外环，内环为344材质40T025/01，这个应该是洛阳石化设计院标准，关于加强管接头等管件STUD BOLT WITH 2 HEAVY NUTS,35CRMOA/35CRMOA，表示一个双头螺栓和2个六角螺母，材质为35CRMOA) c'1 GALV 镀锌 LR 长半径1 t0 y( e. ]$ ^: \$ G4 s d5 E2 PBE 两端平口 MSS SP-95 管件和阀门制造商协会标准* Q8 n& h1 M4 W5 e Z5 |2 P$ p3 厚度4.5MM 304+石墨缠绕垫304+GRAF 344不锈钢材料内环344 INNERRING 碳钢外环CS OUT RING4 洛阳设计院的标准“洛阳石化短接头图集”40T025/015 双头螺栓STUD BOLT WITH 2 HEAVY 螺母NUTS 材质35CRMOA/35CRMOACoupling half 1-1/2NPT 3000PSI ASTM 105CS 是什么意思啊介绍详细点特别是1-1/2NPT 是什么意思？半管接头规格1-1/2NPT （英寸）压力3000英镑碳素钢105CS（相当于20#）GATE VALVE A105 SW 13Cr W/STELLITE SEATS BB OS&Y PLAIN SOLID WEDGE API CL800 API 602SPW-304SS/GRAPHITE% z% r/ T M0 w) G' U8 G ]A105：指ASTM A105 是碳素钢锻件，它相应的中国牌号在GB/T12228-2005中规定为A105（20#钢）SW ：SOCKET WELDED承插焊，( n+ U; B0 ~( f2 e' y7 ?5 T13Cr W/STELLITE SEATS ：阀座材质为13Cr，阀座密封面堆焊了钨铬钴合金（W就是WELD，焊接），Cr13就是含13%Cr的马氏体不锈钢，耐磨耐温。

管件中英文对照

管件中英文对照等径直通equal coupling 异径直通reducing coupling 内牙直通female coupling 夕卜牙直通straight tube with outside 90 等径弯头90 equal elbow 45 等径弯头45 equal elbow 外牙弯头male elbow 内牙弯头female elbow 等径三通equal tee 异径三通reducing tee 内牙三通female tee 夕卜牙三通male tee 管帽capsch代表压力lr长半径或1倍半大小SIZE 数量QTY碳钢弯头Carbon Steel Elbow 不锈钢弯头Stainless Steel Elbow 高压弯头High-Pressure Elbow 同心异径管Concentric Reducers 偏心异径管Ecce ntric Reducers 高压异径管High-pressure Reducers 不锈钢等径三通Stai nless Straight Tee 碳钢等径三通Carbo n Straight Tee 不锈钢等径四通Stai nless Straight Cross 高压三通High-pressure Tee 锻制三通Forged Tee 异径接头Template 管帽Caps 法兰flange长径和短径弯头long and short radius elbows 同心和偏心异径接头concen tric and ecce ntric reducers等径和异径三通straight and reduci ng outlet tees 大小头CONCENTRIC REDUCER Tee Equal相等的三通等径三通Straight Tee异径三通Reduc ing Tee等径四通Straight Cross90 ° 短半径弯头90 ° SS Elbow (SR)90 ° 长半径弯头90 ° SS Elbow (LR)高压厚壁弯头Thick ness ElbowU 型管Return Bend盲法兰Bla nk Fla nge 弯管Bends 翻边stub ends异径接头reducers公称通径nominal diameter夕卜径（mm） outside diameter中心距至端面的距离center to end理论重量（kg/pcs） approx weightdescription 类币中Stan dard 标准Desig n 类型Material 材质双丝头Nipple短节SWAGE NIPPLE内外螺纹活接头Union螺桩studHalf-Coupli ng 单承口管箍Coupling双承口管箍盲板Bli nd Fla nge spectacle bli nd 带双圈的盲板Ecentric偏心的拆除:dismantle结头（管线的）：tie-in插盲板：slip spade盲板：bla nk接头：fitting加热器：heater金属缠绕垫片（带外环）:SW with outside ringHR:热轧manifold:管汇1.2 管件Fitti ng弯头elbow异径弯头reducing elbow带支座弯头base elbowk 半径弯头long radius elbow短半径弯头short radius elbow长半径180° 弯头long radius return 短半径180° 弯头short radius return 带侧向口的弯头（右向或左向）side outlet elbow （right hand or lefthand）双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee （right hand or 1eft hand）异径三通（分支口为异径）reduci ng tee （reduci ng on outlet）异径三通（一个直通口为异径）reduci ng tee （reduc ing on one run）带支座三通base tee异径三通（一个直通口及分支口为异径）reduci ng tee （reduci ng on one runoutlet）异径三通（两个直通口为异径，双头式）reduci ng tee （reduci ng on both runs,bull head）45 斜三通45 ° lateral45 斜三通（支管为异径）45 ° lateral （reducing on branch）45 斜三通（一个直通口为异径）45 ° lateral （reducing on one run）45 斜三通（一个直通口及支管为异径）45 ° lateral （reducing on one run and branch）Y型三通（俗称裤衩）true “ Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reduci ng cross （reduci ng on one outlet）异径四通（一个直通口及分支口为异径）reduci ng cross （reduc ing on one runand outlet）one runand both outlet）异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss管接头coupling, full coupling半管接头half coupling 异径管接头reducing coupling 活接头union内外螺纹缩接（俗称补芯）bushi ng管帽cap （C）堵头plug短节n ipple异径短节reducing nipple; swage nipple1 管道组成件Piping component1.1 管子Pipe管子（按照配管标准规格制造的）pipe管子（不按配管标准规格制造的其他用管）tube辛钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carb on steel pipe合金钢管alloy steel pipe不锈钢sta ini ess steel pipe奥氏体不锈钢管auste nitic sta ini ess steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless （SMLS） steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resista nee welded steel pipe电熔（弧）焊钢板卷管electric-fusio n （arc）-welded steel-plate pipe螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-draw ing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitti ng弯头elbow异径弯头reducing elbow带支座弯头base elbowk 半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow （right hand or left han d）双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee （right hand or left hand）异径三通（分支口为异径）reduc ing tee （reduc ing on outlet）异径三通（一个直通口为异径）reduc ing tee （reduci ng on one run）带支座三通base tee异径三通（一个直通口及分支口为异径）reduci ng tee （reduci ng on one run and outlet）异径三通（两个直通口为异径，双头式）reduci ng tee （reduci ng on both runs, bull head）45°斜三通45 ° lateral45°斜三通（支管为异径）45 ° lateral （reduci ng on bran ch）45° 斜三通（一个直通口为异径）45 ° lateral （reducing on one run）45°斜三通（一个直通口及支管为异径）45 ° lateral （reduci ng on one run and bran ch）Y型三通（俗称裤衩）true “ Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reduc ing cross （reduci ng on one outlet）异径四通（一个直通口及分支口为异径）reduci ng cross （reduci ng on one run and outlet）异径四通（两个分支口为异径）reduci ng cross （reduc ing on both outlet）异径四通（一个直通口及两个分支口为异径）reduci ng cross （reduc ing on one run and both outlet）异径管reducer同心异径管concentric reducer 偏心异径管eccentric reducer 锻制异径管reducing swage 螺纹支管台threadolet 焊接支管台weldolet 承插支管台sockolet 弯头支管台elbolet 斜接支管台latrolet 镶入式支管嘴sweepolet 短管支管台nipolet 支管台•插入式支管台boss 管接头coupling, full coupling 半管接头half coupling 异径管接头reducing coupling 活接头union内外螺纹缩接（俗称补芯）bush ing管帽cap （C）堵头plug 短节n ipple 异径短节reducing nipple; swage nipple1.3 弯管Be nd预制弯管fabricated pipe bend 跨越弯管（A形）cross-over bend 偏置弯管（~形）offset bend 90。

管道及配件中英文对照精品

管道及配件中英文对照精品管道及配件中英文对照化工管道词汇翻译1 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe 螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbow长半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand)双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand)异径三通（分支口为异径）reducing tee (reducing on outlet) 异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet)异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull head) 45°斜三通45° lateral管道及配件中英文对照245°斜三通（支管为异径）45° lateral (reducing on branch)45°斜三通(一个直通口为异径) 45° lateral (reducing on one run) 45°斜三通(一个直通口及支管为异径) 45° later al (reducing onone run and branch)Y型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and outlet)异径四通（两个分支口为异径）reducing cross (reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run and both outlet)异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss(以上带红线的单词已经查过，应该是行业很组合的名词，可以查得到)。

管件中英文对照表 (常用)

碳钢弯头 Carbon Steel Elbow不锈钢弯头 Stainless Steel Elbow高压弯头 High—Pressure Elbow同心异径管 Concentric Reducers偏心异径管 Eccentric Reducers高压异径管 High—pressure Reducers不锈钢等径三通 Stainless Straight Tee碳钢等径三通 Carbon Straight Tee不锈钢等径四通 Stainless Straight Cross高压三通 High-pressure Tee锻制三通 Forged Tee异径接头 Template 管帽 Caps 法兰flange长径和短径弯头 long and short radius elbows同心和偏心异径接头 concentric and eccentric reducers 等径和异径三通 straight and reducing outlet tees大小头 CONCENTRIC REDUCER相等的三通Tee Equal等径三通Straight Tee异径三通Reducing Tee等径四通Straight Cross90°短半径弯头90°SS Elbow (SR) U型管Return Bend 90°长半径弯头90°SS Elbow （LR)高压厚壁弯头Thickness Elbow盲法兰Blank Flange 弯管Bends翻边stub ends 异径接头reducers 公称通径 nominal diameter外径（mm） outside diameter 中心距至端面的距离 center to end理论重量（kg/pcs） approx weight类种description 标准Standard类型Design材质Material 双丝头 Nipple 同心异径短节 SWAGE Nipple活接头 Union PLUGHEX HEAD六角管堵PLUGHEX HEADSCRD六角螺纹管堵MPT螺纹 RC螺纹螺桩 stud SWAGE （CONC）同心异径短节单承口管箍Half-Coupling 异径管箍Coupling, Reducing盲板 Blind Flange 带双圈的盲板spectacle blind偏心的Ecentric等径直通equal coupling内牙直通 female coupling外牙直通 straight tube with outside90等径弯头 90 equal elbow45等径弯头 45 equal elbow外牙弯头 male elbow内牙弯头 female elbow等径三通 equal tee异径三通 reducing tee内牙三通female tee外牙三通 male tee 管帽cap拆除:dismantle 结头（管线的）：tie—in插盲板：slip spade 盲板：blank接头：fitting 加热器：heater金属缠绕垫片（带外环）:SW with outside ring热轧on site：管汇manifold3. 对焊管座weldolet对焊支管台nipolet--短管支管台welding plate flange焊接板式法兰。