聚合物锂电池规格表
聚合物锂电池 YJ802040-600MAH 普通板规格书
A
First Edition
Page 2 o f 1 6
VER: A
深 圳 市 言 九 电 子 科 技 有 限 公 司 YJ POWER GROUP LIMITED
1
DATE:15.10.10
Scope（适用范围） This specification is applied to the reference battery in this Specification and manufactured by
VER: A
深 圳 市 言 九 电 子 科 技 有 限 公 司 YJ POWER GROUP LIMITED
Customer/客户: DATE:15.10.10
Li-ion Polymer Battery Specification
锂离子聚合物电池规格书
MODEL/型号: YJ-PL802040（600mAh）
7
Standard discharge （标准放电）
8
Fast charge (快速充电)
Charge time : Approx 2.5h （充电时间：大约 2.5 个小时）
Page 3 o f 1 6
VER: A
深 圳 市 言 九 电 子 科 技 有 限 公 司 YJ POWER GROUP LIMITED
3.1 Standard Test Conditions（标准测试条件） Test should be conducted with new batteries within one week after shipment from our factory and the cells shall not be cycled more than five times before the test. Unless otherwise specified, test and measurement shall be done under temperature of 20 ± 5 ℃ and relative humidity of 45~85%. If it is judged that the test results are not affected by such conditions, the tests may be conducted at temperature 15~30℃ and humidity 25~85%RH. 测试必须使用出厂时间不超过一个星期的新电池， 且未进行过五次以上的充放电循环。 除非特别说明， 否则测试会在温度 20±5℃，相对湿度 45~85%的条件下进行。如果经鉴定测试结果不受上述条件影响， 测试也可以在温度 15~30℃，相对湿度 25~85%RH 的条件下进行。 3.2 Measuring Instrument or Apparatus（测量器具及设备） 3.2.1 Dimension Measuring Instrument（尺寸测量器具） The dimension measurement shall be implemented by instruments with equal or more precision scale of 0.01mm. 尺寸测量器具的精度等级应不小于 0.01 mm 。 3.2.2 Voltmeter（伏特计） Standard class specified in the national standard or more sensitive class having inner impedance more than 10kΩ/V 按照国家标准指定规格等级或采用灵敏度更高的，测量电压时内阻不应小于 10kΩ/V。 3.2.3 Ammeter（安培计） Standard class specified in the national standard or more sensitive class. Total external resistance including ammeter and wire is less than 0.01Ω. 按照国家标准指定规格等级或采用灵敏度更高的，包括电流表及电线在内的总外阻应小于 0.01Ω。 3.2.4 Impedance Meter（电阻计） Impedance shall be measured by a sinusoidal alternating current method(1kHz LCR meter). 内阻测试仪测量原理应为交流阻抗法（1kHz LCR） 。 3.3 Standard Charge\Discharge（标准充放电） 3.3.1 Standard Charge ：Test procedure and its criteria are referred as follows: 标准充电：测试过程及标准如下： 0.5C5A =300mA Charging shall consist of charging at a 0.5C5A constant current rate until the cell reaches 4.2V. The cell shall then be charged at constant voltage of 4.2 volts while tapering the charge current. Charging shall be terminated when the charging current has tapered to 0.01 C5A . Charge time : Approx 4.0h, The cell shall demonstrate no permanent degradation when charged between 0 ºC and 45 ºC. 电池先 0.5C5A 恒流充至 4.2V，当充电电流逐渐减小时再以 4.2V 恒压充至电流减小到 0.01 C5A， 充电时间大约为 4 个小时。在 0℃-45℃内充电电池应没有永久损害。 3.3.2 Standard Discharge（标准放电） 0.2C5A =120mA Cells shall be discharged at a constant current of 0.2 C5A to 2.75 volts @ 20º 5C 电池以 0.2 C5A 恒流放电至 2.75V @ 20º 5C 3.3.3 If no otherwise specified, the rest time between Chare and Discharge amount to 30min. 如果没有特别说明，电池充放电间隔时间为 30 分。
聚合物锂离子电池产品规格书说明书
Product Specification for Li-ion Polymer Battery 聚合物锂离子电池产品规格书Model电芯型号: 702427(PCM)惠州基安比新能源有限公司HUIZHOU MARKYN NEW ENERGY CO.,LTD.电话: ************传真: ************TEL: ************ FAX : ************SPECIFICATION AMENDMENT RECORDS规格书变更记录1. Scope适用范围：This document describes the Product Specification of the Li-Polymer Rechargeable Battery supplied by Huizhou Markyn New Energy Co., LTD.本规格书描述了惠州基安比新能源有限公司的可充电锂离子聚合物电池的产品性能指标。
2. Description 说明2.1 Description: Li-Polymer Battery类型：锂离子聚合物电池2.2 Model: 702427型号：7024273. Specification产品规格4. Battery Cell Performance Criteria 电芯性能标准4.1 Standard testing environment标准测试环境Unless specifically stated otherwise, tests must be done within one month of delivery and the number of charging-recharging cycles is fewer than 5. The following is test conditions:Test conditions:Ambient Temperature：23ºC ± 2ºCAmbient Humidity：65±20%RH除非另有说明，测试应在电池出货的1个月内进行，且充放电循环的次数少于5次。
电池组装产品规格表
浪颖集团有限公司WWEE GROUP LIMITED电池组装产品规格表Specifications of battery packs18650锂电池组 3.7V 4400mAh18650锂电池组 7.4V 4400mAh AA 5号锂电池 3.7V 700mAh 18650 li-battery pack 3.7V 4400mAh18650 li-battery pack 7.4V 4400mAh AA Size li-ion battery 3.7V 700mAhiphone备用电池锂聚合物电池3.7V 1500mAh GPS防水锂电池 7.4V 2200mAh iphone mobile power li-polymer battery 3.7V 1500mAh Waterproof GPS li-battery 7.4V 2200mAhiphone应急充电器黑莓手机电池 3.7V 1400mAh便携式DVD聚合物电池7.4V 1800mAh iiphone Emergency charger BlackBerry battery 3.7V 1400mAh portable dvd battery 7.4V 1800mAhPSP游戏机电池 3.6V 2400mAh发热服保暖衣锂电池 7.4V 2200mAh发热服保暖衣聚合物电池 7.4V 4400mAh磷酸铁锂动力电池发热服保暖衣锂离子电池7.4V 4400mAh聚合物电池组12V 4000mAhMP3播放器电池3.7V 650mAh动力电池3.6V 8AH手机数码产品应急充电器锂聚合物电池组25.9V 6000mAh电动自行车电池电动汽车电池对讲机电池电动工具/航模高倍率电池理疗保暖聚合物电池蓝牙耳机锂聚合物电池3.7V 120mAh通信终端备用锂电池组可视门铃锂电池3.7V 1200mAh无线扩音器锂电池7.4V 1000mAh磷酸铁锂电池3.2V 100Ah磷酸铁锂电池3.2V 80Ah上网本电池7.4V 6600mAh暖手宝/应急充锂电池镍氢电池组数码相机电池电子菜谱/点菜机聚合物电池太阳能应急充电器军用锂电池组5V应急充电器/备用电源移动电源/应急充电器大容量锂电池组电子烟圆柱聚合物电池USB充电AA电池点读机/学习机电池3.7V 1800mAh便携式DVR锂电池MP4播放器电池3.7V 1600mAh上网本电池 7.4V 2100mAh便携式DVD锂聚合物电池7.4V 1400mAh安防报警器电池7.4V 1000mAhGPS追踪定位器锂电池7.4V 2200mAH移动数字电视电池7.4V 2400mAh可视对讲门铃电池7.4V 1000mAh便携式激光治疗仪电池3.7V 1100mAh ATSC便携式数字电视电池7.4V 2000mAh LED荧光板备用电池12V 4000mAh18650锂电池组7.4V 6600mAh智能玩具电池3.7V 2500mAh数码相框聚合物电池7.4V 2000mAh军用聚合物备用电池3.7V 20AH 电动剃须刀锂电池3.7V 700mAh 18650锂电池组14.8V 2200mAh17670锂电池组18.5V 1700mAh Mini投影仪电池3.7V 2200mAh 26650磷酸铁锂电池组 12V 6AhLED手电筒锂电池3.7V 2200mAh 无线直发器锂聚合物电池3.7V 3600mAh 18500锂电池3.7V 1300mAh发热手套锂电池7.4V 2200mAh GPS导航仪锂聚合物电池3.7V 1300mAh 任天堂游戏机锂电池3.7V 600mAh锂聚合物电池组7.4V 3000mAh iPhone手机电池 3.7V 1400mAh PDA/MID电池3.7V 2800mAh电子巡更棒锂电池3.7V 700mAh电子书/阅读器锂电池 3.7V 1500mAh大容量动力锂电池3.7V 11Ah医疗器械锂电池组LED发光显示电子电池3.7V 1200mAh便携式医疗电子电池3.7V 850mAh锂聚合物电池组14.8V 6000mAh18650锂电池组11.1V 4400mAh手提电脑电池 HP 6芯。
3.2V10AH电池组中文规格书
1.适用范围
本规格书描述的是可充电聚合物锂离子电池的产品性能指标。
2.单只型号：PF69153257-100000mah
3.尺寸：
项目
描述
尺寸
T
厚度
65.0mm max
W
宽度
153mm max
L
长度
253mm max
B
极柱高度
16±1mm
4.规格
废弃之电池应用绝缘纸包住电极,以防起火、爆炸
5
热冲击安全性能
不起火、不爆炸
测量电池的初始状态，电池标准充电后，放置于热箱中，并与热电偶相连，温度以（5±2℃）/min的速率升至150±2℃并保温30Min。观察电池外观变化
5.3环境适应性能
序号
项目
标准
测试方法
1
热循环性能
不漏液、不冒烟、不起火、
不爆炸。
电池标准充电后,在环境温度为75±2℃℃的条件下开路放置48h，后在-20℃条件下开路放置6h，后在室温条件下开路放置24h。观察电池外观变化。
5.2安全性能
序号
项目
标准
测试方法
1
过充性能
不爆炸、不起火，
最高温度<130℃
电池标准充电后，测量电池的初始状态，保证电池状态正常（下同）,以3C5A电流充电至10.0V，然后转恒压充电至截至电流0.01C5A时终止，观察电池的温度及外观变化。
2
过放性能
不起火、不爆炸
电池标准充电后，测量电池初始状态，以0.2C5A进行放电至2.0V，然后用10Ω的电阻将电池正负极相连，搁置14天。观察电池外观变化。
使用规定的充电器
聚合物规格表10.31
额定容量典型容量 内阻 重量 极耳中间距极耳宽T(±0.2)W(±0.5)L(±0.5)(mAh)(mAh)(mΩ)(±3%g)(±1mm)(±0.2mm)1561ICP324880P 3.2max 48.0max 80.0max12301280≤5024.216.0 4.02464ICP332527P 3.1≤25.0≤27.0(含极耳胶)150165≤180 3.08.0 2.03560ICP344880P 3.4max 48.0max 80.0max 13301420≤5026.516.0 4.04302ICP355585P 3.555.085.017001750≤4535.024.0 5.05319ICP355597P 3.355.096.519001940≤5039.028.0 4.06331ICP3567103P 3.367.0102.525002550≤4551.518.0 5.07479ICP381223P 3.90max 12.5max 23.0max (含极耳胶）7075≤350 1.7~2.0 3.0 2.08301ICP383562P 3.635.062.0830850≤5017.514.0 4.09419ICP383562P2 3.835.062.0850880≤5018.014.0 4.010324ICP401235P 4.012.035.0120125≤180 2.9 4.0 2.011321ICP401745P 4.017.045.0260270≤100 5.3 5.0 2.012375ICP406297P 4.062.097.027503050≤3556.532.0 5.013434ICP423557P 4.034.557.0910930≤5017.010.0 4.014470ICP423955P 4.2039.755.910001050≤6019.510.0 4.015349ICP425585P 4.255.085.021002145≤3543.024.0 5.016413ICP4357100P4.256.097.025002550≤4053.026.04.0序号产品代码产品型号外形尺寸(mm)聚合物锂离子电池产品规格表版 次：D/1页 码：第1页 共4页额定容量典型容量 内阻 重量 极耳中间距极耳宽T(±0.2)W(±0.5)L(±0.5)(mAh)(mAh)(mΩ)(±3%g)(±1mm)(±0.2mm)17554ICP4450113P 4.40max 50.00max 113.5max (含极耳胶）28002930≤5052.516.0 5.018512ICP454093P 4.50max 40.0max 93.0max 18001870≤4033.616.0 4.019380ICP454461P 4.443.560.513001340≤5025.024.0 3.020558ICP484651PA 4.8max 46.3max 51.6max 1400/≤6024.214.0 4.021318ICP496479P 4.763.578.527002750≤4552.015.0 3.022438ICP501525P 4.4±0.414.50±0.824.7110120≤200 2.5 5.0 2.023322ICP501858P 5.018.058.0520550≤8010.0 5.0 2.024435ICP502025P 5.15max19.70±0.825.0190205≤180 4.07.0 2.025429ICP502029P 4.819.2±0.830.2±0.8(含极耳胶)220230≤120 4.5 6.0 2.026305ICP502030P 5.019.7±0.830.0240260≤120 4.96±0.5 6.0 2.027314ICP502035P 5.020.2max 35.2max 320335≤907.0 6.0 2.028556ICP502258P 5.0max 22.0max 58.0max640680≤7012.1 6.0 2.029460ICP502430P 4.8≤24.4≤29.7(含极耳胶)290300≤120 5.58.0 2.030345ICP503759P 5.037.059.012001220≤5022.510.0 4.031535ICP505573P 5.0max 55.0max 73.5max 23502420≤6042.026.0 4.032363ICP505597P5.055.096.530003050≤3556.533.04.0聚合物锂离子电池产品规格表序号产品代码产品型号外形尺寸(mm)版 次：D/1页 码：第2页共4页额定容量典型容量 内阻 重量 极耳中间距极耳宽T(±0.2)W(±0.5)L(±0.5)(mAh)(mAh)(mΩ)(±3%g)(±1mm)(±0.2mm)33426ICP505874P 4.858.074.022502300≤4043.033.0 4.034340ICP522850P 5.228.050.0700720≤5514.013.0 3.035347ICP523450P 5.234.050.0880920≤6018.014.0 4.036537ICP524064P 5.2max 40.0max 64.0max 14501500≤6029.016.0 4.037519ICP5259115P 5.2max 59.0max 115.5max 36503800≤5072.013.0 5.038510ICP534445P 5.3max 44.0max 46.0max 10801140≤6021.014.0 4.039364ICP5367103P 5.3067.0102.540004200≤3080.032.0 5.040344ICP542447P 5.224.047.0600620≤6011.5 6.5 2.041350ICP551430P 5.514.030.0170180≤150 3.5 4.0 2.042446ICP551729P 5.3017.028.5180190≤150 3.5 5.0 2.043563ICP554443P 5.5max 44.0max 43.0max10301080≤6019.5 4.016.044522ICP5550105P 5.5max 50.0max 105.0max (含极耳胶）30003150≤3056.516.0 5.045421ICP583436P 5.833.535.5600620≤7012.514.0 3.046422ICP583759P 5.637.059.014001450≤5025.510.0 4.047487ICP603395P 6.0max 33.0max 93.0max 20002080≤4037.59.0 5.048385ICP604296P6.042.096.028002840≤4052.017.04.0深圳华粤宝电池有限公司聚合物锂离子电池产品规格表序号产品代码产品型号外形尺寸(mm)文件编号：HYB/QI-13-944版 次：D/1页 码：第3页 共4页额定容量典型容量 内阻 重量 极耳中间距极耳宽T(±0.2)W(±0.5)L(±0.5)(mAh)(mAh)(mΩ)(±3%g)(±1mm)(±0.2mm)49513ICP604396P 6.0max 42.5max 96.0max 25002600≤4046.516.0 4.050502ICP606075P 6.0max 60.0max 75.0max 30003130≤4055.016.0 5.051565ICP615085P 6.1max 50.0max 85.0max 32003300≤6057.0 4.016.052442ICP623965P 6.038.564.517001750≤5034.014.0 4.053415ICP686560P 6.865.060.028002850≤4054.015.0 4.054453ICP703961P 6.80±0.2538.762.7±1.0(含极耳胶)18001830≤5033.511.0 4.055550ICP705462P 7.00max 54.00max 62.50max 27002800≤5547.523.0（左偏1mm）5.056511ICP705575P 7.0max 55.0max 75.0max 30003120≤5053.523.5 4.057427ICP723048P 7.2max 30.0max 48.0max 10001050≤6019.09.0 4.058371ICP963450P9.634.050.017501780≤5031.010.04.0序号产品代码产品型号外形尺寸(mm)深圳华粤宝电池有限公司聚合物锂离子电池产品规格表文件编号：HYB/QI-13-944版 次：D/1页 码：第4页 共4页。
聚合物锂电池型号释义
聚合物锂电池型号释义同学们！今天咱们来好好聊聊聚合物锂电池的型号释义。
这聚合物锂电池啊，在我们的生活中可越来越常见了，从手机到平板电脑，从蓝牙耳机到智能手表，很多地方都能看到它的身影。
但是，你知道那些一串串的型号都代表着什么意思吗？别着急，听我慢慢道来。
咱们得知道聚合物锂电池是啥。
聚合物锂电池就是一种比较先进的电池。
它和我们以前常见的那种圆柱形的电池不太一样，聚合物锂电池通常是扁扁的，形状可以根据需要进行设计。
而且它的性能也很不错，容量大、重量轻、安全性高。
那聚合物锂电池的型号是怎么回事呢？聚合物锂电池的型号是由一串字母和数字组成的。
这些字母和数字可不是随便乱写的哦，它们都有着特定的含义。
比如说，型号中的数字通常会表示电池的容量。
容量呢，就是这个电池能够储存多少电量。
数字越大，容量就越大，电池能用的时间也就越长。
比如，一个型号为“1000mAh”的聚合物锂电池，就表示它的容量是1000 毫安时。
如果你的手机电池是这个型号的，那在正常使用的情况下，可能可以让你的手机用比较长的时间呢。
除了容量，型号中的字母也有特定的含义。
有些字母可能表示电池的尺寸。
比如，“L”可能表示长条形的电池，“S”可能表示正方形的电池。
这样，我们通过型号就能大概知道电池的形状和大小了。
还有一些字母可能表示电池的性能特点。
比如，“H”可能表示高容量的电池，“F”可能表示快速充电的电池。
如果你的手机需要经常充电，那你可能就会选择一个带有“F”字母的聚合物锂电池，这样可以让你的手机充电更快，更方便。
型号中还可能会有一些特殊的符号。
比如，“+”“-”号可能表示电池的正负极。
这个很重要哦，我们在使用电池的时候一定要注意正负极的连接，不然可能会损坏设备或者引发危险。
在实际生活中，我们怎么根据型号来选择合适的聚合物锂电池呢？这可就有讲究啦。
首先，我们要根据自己的设备需求来选择容量合适的电池。
如果你的设备需要长时间使用，那你就可以选择容量大一点的电池。
锂电池规格参数表
3 85120 PL1585120M 14500 ≤15 3.7
4 5064 PL155064P 3600 ≤40 3.2
5
PL136067P 3000 ≤40 3.2
6 6067 PL166067P 5000 ≤40 3.2
7 8067 PL158067P 6500 ≤40 3.2
厚度(±0.2) 15 10 15 15 13 16 15
长度(±0.5) 67.5 64.5 67.5 67.5 67.5 67.5 67.5 67.5 70.5 80.5 64.5 67.5 67.5
序
标称容量 内阻 标称电压
号 系列 型 号
(mAh) (mΩ) (V)
1 77100 PL1577100M 9000 ≤20 3.7
2
PL1085120M 10000 ≤15 3.7
厚度 (±0.2) 3.2 6.5 5 4 5 6 3.8 4 4 5 5 6 3.8 5 8 3.8 3.5 3.8 4 5 5.2 5.8 4 5 6 6.3 5 5 4 5 5.8 5.2 4.2 6 6 5 4 7.2
尺寸(mm) 宽度(±0.5)
10.5 11.5 12.5 12.5 12.5 12.5 14.5 14.5 14.5 14.5 16.5 17.5 17.5 17.5 19.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 21.5 22.5 27.5 30.5 30.5 30.5 30.5 30.5
1
PL363450A 550 ≤55 3.7
3.8
2
PL383450A 600 ≤55 3.7
锂离子电池规格表
锂离子电池规格表（北京天锐驰能源科技公司）1 聚合物锂离子电池聚合物锂离子电池具有安全性能好、厚度薄、重量轻、容量大、自放电小、形状可定制、有平稳的放电特性和更高的放电平台、保护板设计简单等优势，开发新的电芯型号，价格便宜，开模周期短，被广泛地应用于 MP3 、 MP4 播放器、蓝牙耳机、手机、笔记本电脑，移动 DVD 、小型电动工具，玩具等。
2 聚合物锂离子矿灯电池产品特点安全性：采用锰酸锂或磷酸铁锂作正极材料，铝塑膜软包装，整体密封设计，具有良好的安全性能。
经国家权威机构检验，该电池在重物冲击、高温、过充电、短路的条件下测试，电池不起火、不爆炸方便性：体积小、重量轻、携带方便、免维护、充电简便、使用方便。
体积和重量只有传统铅酸矿灯的五分之一左右。
耐用性：使用寿命长，维护费用大大降低。
适应性：可根据客户需求设计电池并加装保护电路，提供相关技术支持。
环保性：所用材料中不含镉、铅、汞之类的有害重金属物质，在生产及使用过程中没有污染物产生，废电池回收过程中不存在污染水源和土壤的问题。
M －锰酸锂电池 P －磷酸铁锂电池电池容量、形状和尺寸可根据客户要求进行量身定制。
3 聚合物锂离子动力电池和电池组电动车的发展将是交通业未来发展的必然趋势，在众多的电动车的动力电池体系中，最有发展前景的当数锂离子动力电池。
锂离子动力电池可用磷酸铁锂或锰酸锂作正极材料，可根据需要组成电池组。
装载锂离子电池组的电动车重量轻、循环寿命长、安全性好。
本公司可根据客户需求生产容量为 10Ah 、 15 Ah ，电压为 6V 、 9V 、 12V 、 24V 、 36 V 、48 V 等不同规格的电池组。
本公司还可生产各种仪表、小型电动工具、电动玩具专用的锂离子电池组，目前生产的有磷酸铁锂 9V 电池组，容量有 120mAh 、 160mAh 、 200mAh 等。
单体电池技术指标M －锰酸锂电池 P －磷酸铁锂电池电池容量、形状和尺寸可根据客户要求进行量身定制。
聚合物锂电池401520规格书
egrahC dradnatS smetI
电充准标
1 .O N
能性电放充 scitsiretcarahc lacirtcelE 1.4
airetirC ecnamrofreP lleC yrettaB.4
试测及查检能性芯电
41 fo 4 :EGAP A : .VER 810 :.ON COD
司公限有技科子电达立迅海珠
寸尺芯电 noisnemiD lleC 量重芯电 thgieW lleC 度温存储 erutarepmet egarotS 度温作工 erutarepmet gnitarepO 压电止截电放 egatlov ffo-tuc egrahcsiD 流电电放大最 tnerruc egrahcsid.xaM 流电电充大最 tnerruc egrahc.xaM 间时电充 emit gnigrahC 法方电充准标 dohtem gnigrahC dradnatS 流电电充 tnerruc egrahC 量容称标 yticapac lanimoN 压电称标 egatlov lanimoN smetI 压电电充 egatlov egrahC
认确户客
准批
核审
定制
025154 SCI
025154 SCI �号
:ledoM
型
�芯电�书认确格规品产 )lleC(teehS lavorppA noitacificepS
41 fo 1 :EGAP A : .VER :.ON COD 810
司公限有技科子电达立迅海珠
31 21 11 01 01 9 8 7 7 6 5 4 3 3 3
定确商协方双经须�项事的及提未中书明说本何任 .NUJOUHZ dna remotsuc eht neewteb derrefnoc eb dluohs revoc ton seod noitacificeps siht taht srettam ynA 项事它其 srehtO )b
锂电池规格参数表
1
PL363450A 550 ≤55 3.7
3.8
2
PL383450A 600 ≤55 3.7
4
3
PL413450A 700 ≤55 3.7
4.4
3450
4
PL423450A 700
≤55
3.7
4.4
5
PL053450A 850 ≤55 3.7
5.3
6
PL063450A 950 ≤55 3.7
6.3
1
PL042040P 180 ≤160 3.2
本公司可根据客户需求生产容量为 10Ah 、15Ah ，电压为 6V 、9V 、12V 、24V 、36V 、 48V 等不同规格的电 池组。
本公司还可生产各种仪表、小型电动工具、电动玩具专用的锂离子电池组，目前生产的有磷酸铁锂 9V 电池组， 容量有 120mAh 、160mAh 、200mAh 等。
≤70
3.7
3.8
3553
46
PL053553 840
≤70
3.7
5
47 4450 PL124450 1800 ≤60
3.7
12
34.5
50.5
13.5
34.5
50.5
14.5
34.5
50.5
31
34.5
65.5
20.5
34.5
65.5
33.5
35.5
43.5
19
35.5
53.5
9
PL041430 120
1430
10
PL051430 150
11 1646 PL051646 280
12 1736 PL061736 280
Polymer 锂离子电池产品规格说明书
Specification Approval Sheet Name：Polymer Lithium-Ion BatteryModel： CELLEVIA BATTERIES LP573450SPEC：3.7V/ 980mAhNumber: 573450Specification Modification RecordsContent1.Scope:This specification describes the Product Specification of chargeable Polymer Lithium-IonBattery produced by Cellevia.Any copies are invalid without our company’s approval2.Model :3.Cell parameters Index:3.2 Parameters of batterythe temperature.4.Electronic Characteristics test and inspection:4.1 Standard testing environmentUnless special stated, tests should be done within one month of delivery and thecharging-recharging times is less than 5 times. The following is test conditions: Ambient Temperature： 25℃±0.5℃Ambient Humidity： 65 ±20%4.2 The requirement of measure instrument(1) The measure instrument is passed tested by qualified institute.(2) The accuracy of the size instrument is not more than 0.01mm.(3) The accuracy of multimeter is not less than 0.5%. while measure the voltage, theinternal resistance mustn’t less than 10KΩ.(4) The principal of the internal resistance is 1KHz LCR, the accuracy is 0.2%.(5) The internal resistance is changeable, it varies according to the temperature and thecharging mode. And it is relevant to the PTC and the length and the Capacity of the drawing line.(6) The current accuracy of the battery test system is more than ±0.1%,isobaricallyaccuracy is ±0.5%, timer accuracy is less than ±0.1%.(7) The accuracy of the temperature meter is less than ±0.5℃.4.3 Visual inspectionAny visual inspection defects will affect the electronic characteristics, such as cracks,leakage, and flaw, are not inexistence.Notes： The Max. voltage while charging is not more than 4.25V.The Max.protective voltage designed on PCB board should not more than4.3V.5. Storage and others5.1 Long Period StorageIf the cell has been stored for 3 month, it should be transfer to a dry and cool environment. Storage Voltage is between 3.6V and 3.9V and the storage conditions as Item 4.1.5.2Any matters that this specification does not cover should be conferred between theSpecification Approval sheet6.Drawing6.1 Assembly diagram(not in scale)Model：L573450! Danger●Strictly prohibits heat or throw cell into fire.●Strictly prohibits throw and wet cell in liquid such as water, gasoline or drink etc.●Strictly prohibits use leave cell close to fire or inside of a car where temperature may be above60°C. Also do not charge / discharge in such conditions.●Strictly prohibits put batteries in your pockets or a bag together with metal objects such asnecklaces. Hairpins,coins, or screws. Do not store or transportation batteries with such objects.●Strictly prohibits short circuit the (+) and (-) terminals with other metals.●Do not place Cell in a device with the (+) and (-) in the wrong way around.●Strictly prohibits pierce Cell with a sharp object such as a needle.●Strictly prohibits disassemble or modify the cell.●Strictly prohibits welding a cell directly.●Do not use a Cell with serious scar or deformation.●Thoroughly read the user’s manual before use, inaccurate handling of lithium ion rechargeablecell may cause leakage, heat, smoke, an explosion, or fire, capacity decreasing.! Warning●Strictly prohibits put cell into a microwave oven, dryer, or high-pressure container.●Strictly prohibits use cell with dry cells and other primary batteries, or new and old battery orbatteries of a different package, type, or brand.●Stop charging the Cell if charging is not completed within the specified time.●Stop using the Cell if abnormal heat, odor, discoloration, deformation or abnormal condition isdetected during use, charge, or storage.●Keep away from fire immediately when leakage or foul odor is detected.●If liquid leaks onto your skin or clothes, wash well with fresh water immediately.●If liquid leaking from the Cell gets into your eyes, do not rub your eyes. Wash them well with cleanedible oil and go to see a doctor immediately.! Caution●Before using the Cell, be sure to read the user’s manual and cautions on handling thoroughly.●Charging with specific charger according to product specification. Charge with CC/CV method.Strictly prohibits revered charging. Connect cell reverse will not charge the cel. At the sametime, it will reduce the charge-discharge characteristics and safety characteristics, this will leadto product heat and leakage.●Store batteries out of reach of children so that they are not accidentally swallowed.●If younger children use the Cell, their guardians should explain the proper handling.●Before using the Cell, be sure to read the user’s manual and cautions on handling thoroughly.●Batteries have life cycles. If the time that the Cell powers equipment becomes much shorter thanusual, the Cell life is at an end. Replace the Cell with a new same one.●When not using Cell for an extended period, remove it from the equipment and store in aplace with low humidity and low temperature.●While the Cell pack is charged, used and stored, keep it away from objects or materials with staticelectric charges.●If the terminals of the Cell become dirty, wipe with a dry clothe before using the Cell.●Storage the cells in storage temperature range as the specifications, After full discharged, wesuggest that charging to 3.9~4.0V with no using for a long time.●Do not exceed these ranges of the following temperature ranges.Charge temperature range : 0 °C to 45 °C;Discharge temperature range : -20 °C to 60 °C.(When using equipment)Handling Precaution and GuidelineFor LIP (Lithium-Ion Polymer) Rechargeable BatteriesPrefaceThis document of ‘Handling Precautions and Guideline LIP Rechargeable Batteries’shall be applied to the battery cells manufactured by CELLEVIA.Note (1): The customer is requested to contact CELLEVIA in advance, if and when the customer needs other applications of operating conditions than those described in this document. Additional experimentation may be required to verify performance and safety under such condition.Note (2): CELLEVIA will take no responsibility for any accident when the cell is used under other condition.Note (3): CELLEVIA will inform, in a written form, the customer of improvement(s) regarding proper use and handling of the cell, if it is deemed necessary.1. Charging 1.1ChargingCurrent:Charging current should be less than maximum charge current specified in theSpecification Approval Sheet.1.2 Charging Voltage:Charging voltage should be less than the maximum nominal voltage 4.2V, andthe charging voltage upper limited is 4.30V(single pack).1.3 Charging Temperature:The cell should be charged within the range specified in this Specification ApprovalSheet.1.4 Notes:Since charging with constant current or constant voltage, reverse charging isprohibited. In case of the cell is connected improperly, the cell cannot be charged.Simultaneously, the reverse charging may cause damaging to the cell whichmay lead to degradation of cell performance and damage the cell safety, andcould cause heat generation or leakage.2. Discharging Current:The cell shall be discharged at less than the maximum discharge current specified in the Specification Approval Sheet. High discharging current may reduce the discharging capacity significantly or cause over-heat.3. Discharging TemperatureDischarging Temperature should be within the range specified in this Specification Approval Sheet.4.Over-DischargeOver-discharging will cause cell low-performance and function loss. The cell would be in a over-discharged state by its self-discharge characteristic. In order to prevent over-discharging, the cell shall be charged periodically to maintain between 3.6V and 3.9V.5. Protective Circuit Module5.1 The cell / battery pack shall be with a PCM that can protect cell / battery packproperly. PCM shall have functions of(1) Overcharging prevention(2) Over-discharging prevention(3) Over current prevention to maintain safety and prevent significant deteriorationof cell performance. The over current can occur by external short circuit.5.2 Overcharging ProtectionOvercharging prevention function shall stop charging if any cell of the battery packreaches 4.30V.5.3 Over-discharging protectionOver-discharging protection function shall monitor the voltage of every cell in the pack, and work to avoid further drop in the cell voltage of 2.75V or less.6. StorageCells should be stored in proper temperature specified in Specification ApprovalSheet.7. AppearanceIt shall be free from any defects such as remarkable scratches, breaks, cracks,discoloration, leakage or deformation .8. Notice△!8.1 Handling of cells:Avoid any short-circuit, it will caused the pole hot and lost electronic functions.Soft packing is very damaged by sharp edge parts such as needles and knives.Avoid cells touch with sharp edge part, when handling and storage.Beside the poles is the sealed edge. Don’t bend or fold dealing edge, for it is a sensitive part.Don’t open the folding edge on both sides of the cells.Don’t bend the tabs, for the tabs are not so stubborn.Avoid mechanical shock to the cells.Don’t put the cells into the heater, washing machine or high-voltage container.Don’t use the charger without any safety guarantee, and recommend you use specified charger.You should immediately stop charging, as cell is overheating, delivery any smell, changed color, distortion etc.Before Children use batteries, adults should explain the usage first.Before use batteries, please read the handling guideline carefully and fully understand.Away from the static-electronic field, while using, charging and storing cells.Don’t put the cells together with metal conductors such as chains, barrette, bolt into the pocket or stored them together.Don’t use metal conductor to shortcut the positive and negative poles.Don’t mis-assemble the positive pole with the negative one.8.2 Notice for Designing Battery Pack8.2.1 Package DesignBattery pack should have sufficient strength and battery should be protected from mechanical shock.No sharp edge components should be inside the pack containing the battery.The overcharge threshold voltage should not be exceed 4.30V (single pack)The over-discharge threshold voltage should not be lower than 2.75V (single pack)The PCM should have short protection built inside.8.3 Notice for Assembling Battery Pack8.3.2 Tab connectionUltrasonic welding or spot welding is recommended to connect battery with PCM or other parts.If apply manual solder method to connect tab with PCM, below notice is very important to ensure battery performance.8.3.2.1 The solder iron should be temperature controlled and ESDsafe.8.3.2.2 Soldering temperature should not exceed 350℃.8.3.2.3 Soldering time should not be longer than 3 seconds .8.3.2.4 Keep battery tab cold down before next time soldering.8.3.2.5 Directly heat cell body is strictly prohibited. Battery shouldbe damaged by heat above approx. 60℃.8.3.3 Cell fixingThe battery should be fixed to the battery pack by its large surface area.No sharp edge at the assembling position.No cell movement in the battery pack should be allowed.9.Others9.1 The disassembling may generate internal shout circuit in the cell, which may causegassing, firing, or other problem.9.2 Prohibition of dumping of cells into fireNever incinerate or dispose the cells in fire, for these may cause firing of the cells.9.3 The cells should never be soaked with liquids such as water, drinks or oil.9.4 Prohibit using the cells mixed with different manufactories. Prohibit using new cellsmixed with old ones.▲Special Notice: If the cell isn’t used for a long time, Please Keep the cells in half-charged state, which is keeping them unfully charged or incompletely discharged. Recharge the cells and use half of the power after 2-3months. Store the cells in cool and dry place. It will protect the cell from damage effectively and long-term.10. StatementIf our specifications material, product process or product control system has changed, the information will be transmitted to consumer by way of written with quality and reliability data.。
2011-11-28比克锂离子(聚合物)电芯规格表
电芯极耳 产品可使 中心距 用范围 （mm） Applicab Cell Tab le scope Pitch
备注 Remarks
73.50 2.85 ≤60 16.00 18.0±1.5
已送样,待客户确 认书
2 201124P
28 JOC 3.7 2.60 11.00 24.50 0.10 ≤500 0.50 5.5±1.5
Code （V）
宽度 Width Max (mm)
1 254973P
770 JHR 3.7 2.50 49.60
P3-BE/PLB/CT-005
A/00
2011-11-28
高度 瓦特/时 内阻 重量
Height watt Internal Weight Max hour resistance (g) (mm) (WH) （mΩ)
25 346595P
2200 JMG 3.7 3.60 65.50 95.50 8.14 ≤60 45.90 38.0±1.5
试产阶段
26 363031P
270 JPH 3.7 3.60 30.00 31.50 1.00 ≤150 5.10 10.5±1.5
试产中
27 363830P 28 364175P 29 355462P 30 365079P 31 372318P 32 374237P
送样OK,暂无订 单需求
2400 JDO 3.7 3.90 69.80 85.50 8.88 ≤80 46.00 44.5±1.5
已送样,待客户确 认书
3300 JSD
55 JOW 3.7 3.80 12.40 19.50 0.20 ≤400 1.04 5.0±1.5
39 381223P 40 382040P 41 383030P
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
版 本制定日期页 次1222441150140180 3.7 3.5±0.52263030200190130 3.74±1330153310095300 3.72±14301550170160200 3.7 3.4±0.55302029140130200 3.7 2.8±0.56302025110100270 3.7 2.8±0.57302040190185140 3.7 3.8±0.58302222105100300 3.7 2.1±0.59302236190190150 3.7 3.8±0.510302248260260100 3.7 5.2±0.511302425150140200 3.73±0.5123007457070380 3.7 1.4±0.51330074565380 3.7 1.3±0.514302323120120250 3.7 2.4±0.515302535210200140 3.7 4.2±0.516302540230230120 3.7 4.6±0.517302626150140200 3.73±118303040310310100 3.7 6.2±0.51930304840040090 3.78±12030345050050070 3.710±12130346060060060 3.712±12233344850070 3.710±12333346265065060 3.713±124303535310310100 3.7 6.2±12530404550049070 3.710±12630436068068045 3.713.6±1273245100140060 3.728±1283512205045450 3.7 1.5±0.5293514279090270 3.7 1.8±0.530352025********* 3.7 2.6±0.531353035********* 3.7 6.2±1323565852000195040 3.738±13336132070350 3.7 1.4±13437515295095045 3.719±135381429130240 3.7 2.6±13638345065065060 3.713±13.20-0.3 *45.0+0.5-0.5 *100.5+0.5-0.53.80.2-0.3 *14.0+0.5-0.5 *29.0+0.5-0.5A 2009-12-09PAGE 1 OF 63.90-0.3 *13.0+0.5-0.5 *20.0+0.5-0.53.80-0.3 *34.0+0.5-0.5 *50.0+0.5-0.53.50-0.3 *14.0+0.5-0.5 *27.0+0.5-0.53.50-0.3 *65.0+0.5-0.5 *85.0+0.5-0.53.10-0.3 *34.0+0.5-0.5 *50.0+0.5-0.53.00-0.3 *34.0+0.5-0.5 *59.0+0.5-0.53.30-0.3 *34.0+0.5-0.5 *61.0+0.5-0.53.10-0.3 *40.0+0.5-0.5 *45.0+0-0.5深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY TECHNOLOGY CO., LTD.尺寸(mm)序号最小容量（mAh） 3.70-0.3 *51.0+0.5-0.5 *52.0+0.5-0.53.10-0.3 *30.0+0.5-0.5 *48.0+0.5-0.5量产规格表3.10-0.3 *43.0+0.5-0.5 *60.0+0.5-0.53.50-0.3 *20.0+0.5-0.5 *25.0+0.5-0.53.50-0.3 *30.0+0.5-0.5 *35.0+0.5-0.5内阻（mΩ）标称容量（mAh）型号 3.10-0.3 *15.0+0.5-0.5 *50.0+0.5-0.53.10-0.3 *20.0+0.5-0.5 *29.0+0.5-0.53.10-0.3 *20.0+0.5-0.5 *25.0+0.5-0.53.10.1-0.3 *20.0+0.5-0.5 *40.0+0.5-0.53.00.3-0.3 *7.0+1.5-0.5 *45.0+0.5-0.53.10-0.3 *25.0+0.5-0.5 *35.0+0.5-0.53.10-0.3 *22.0+0.5-0.5 *36.0+0.5-0.5电压（V）重量（g)厚×宽×高2.750-0.3 *30.0+0.5-0.5 *30.0+0.5-0.52.20-0.3 *24.0+0.5-0.5 *41.0+0.5-0.53.10-0.3 *30.0+0.5-0.5 *40.0+0.5-0.53.10-0.3 *15.0+0.5-0.5 *33.0+0.5-0.53.10-0.3 *35.0+0.5-0.5 *35.0+0.5-0.53.10-0.3 *22.0+0.5-0.5 *48.0+0.5-0.53.10-0.3 *25.0+0.5-0.5 *40.0+0.5-0.53.10-0.3 *26.0+0.5-0.5 *26.0+0.5-0.53.10.1-0.3 *23.0+0.5-0.5 *23.0+0.5-0.53.50-0.3 *12.0+0.5-0.5 *20.0+0.5-0.53.30-0.3 *34.0+0.5-0.5 *48+0.5-0.53.10-0.3 *22.0+0.5-0.5 *22.0+0.5-0.53.20-0.3 *24.0+0.5-0.5 *25.0+0.5-0.53.00.3-0.3 *7.0+1.0-0.5 *45.0+0.5-0.5版 本制定日期页 次3738364155055070 3.711±13838112580330 3.7 1.6±13940103080330 3.7 1.5±0.5404011174040600 3.7 1.5±0.5414011206060430 3.72±0.5424012258075330 3.72±0.543401229100100300 3.72±0.544401235120120200 3.7 2.4±0.545401429120120200 3.7 2.4±0.546401445200200130 3.74±0.547401525110240 3.7 2.2±0.548401730160160180 3.7 3.2±0.549402020110110240 3.7 2.2±0.550402023130120200 3.7 2.6±0.551402025150145180 3.73±0.552402030190190130 3.7 3.8±0.553402035220220130 3.7 4.4±0.554402040280260100 3.7 5.6±155402535300300100 3.76±15640254034034090 3.7 6.8±157402626210210130 3.7 4.2±15840304046046070 3.79.2±15940304858058060 3.711.6±16040344050050070 3.710±16140345068068060 3.713.6±16240471082000200040 3.738±1634215155550420 3.7 1.1±0.5644315178080350 3.7 1.6±0.5654411206060380 3.7 1.2±0.56645102780330 3.7 1.6±0.5674511154040500 3.71±0.5684511175050500 3.71±0.56945121760430 3.71±0.5704512207070350 3.7 1.8±0.571451225100100300 3.72±0.572451235130200 3.7 2.6±0.54.00-0.3 *15.0+0.5-0.5 *25.0+0.5-0.54.00-0.3 *12.0+0.5-0.5 *35.0+0.5-0.54.00-0.3 *14.0+0.5-0.5 *29.0+0.5-0.54.00-0.3 *12.0+0.5-0.5 *29.0+0.5-0.54.00-0.3 *11.0+0.0-0.5 *17.0+0.5-0.53.80-0.3 *11.0+1.0-0.5 *25+0.5-0.54.00-0.3 *10.0+0.7-0.5 *30+0.5-0.54.00-0.3 *20.0+0.5-0.5 *30.0+0.5-0.54.00-0.3 *12.0+0.5-0.5 *25.0+0.5-0.54.50-0.3 *12.0+0.5-0.5 *35.0+0.5-0.54.00-0.3 *34.0+0.5-0.5 *40.0+0.5-0.54.00-0.3 *47.0+0.5-0.5 *108.0+0.5-0.54.00-0.3 *11.0+0.0-0.5 *20.0+0.5-0.5厚×宽×高内阻（mΩ）最小容量（mAh）A 2009-12-09PAGE 2 OF 6电压（V）重量（g)量产规格表序号型号标称容量（mAh） 4.00-0.3 *20.0+0.5-0.5 *40.0+0.5-0.54.00-0.3 *34.0+0.5-0.5 *50.0+0.5-0.54.50-0.3 *12.0+0.5-0.5 *20.0+0.5-0.54.50-0.3 *10.0+0.5-0.5 *27.0+0.5-0.54.20-0.3 *15.0+0.5-0.5 *15.0+0.5-0.54.30.2-0.3 *15.0+0.5-0.5 *17.0+0.5-0.54.50-0.3 *11.0+0-0.5 *17.0+0.5-0.54.50-0.3 *12.0+0.5-0.5 *25.0+0.5-0.54.40-0.3 *11.0+0.5-0.5 *20.0+0.5-0.54.00-0.3 *25.0+0.5-0.5 *35.0+0.5-0.54.00.1-0.3 *26.0+0.5-0.5 *26.0+0.5-0.54.00-0.3 *30.0+0.5-0.5 *40.0+0.5-0.54.00-0.3 *30.0+0.5-0.5 *48.0+0.5-0.54.00-0.3 *25.0+0.5-0.5 *40.0+0.5-0.54.00-0.3 *20.0+0.5-0.5 *25.0+0.5-0.54.00-0.3 *20.0+0.5-0.5 *35.0+0.5-0.54.00-0.3 *17.0+0.5-0.5 *30.0+0.5-0.53.80-0.3 *36.0+0.5-0.5 *41.0+0.5-0.5深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY TECHNOLOGY CO., LTD.尺寸(mm)4.50-0.3 *12.0+0.5-0.5 *17.0+0.5-0.54.50-0.3 *11.0+0.5-0.5 *15.0+0.5-0.54.00-0.3 *20.0+0.5-0.5 *20.0+0.5-0.54.00-0.3 *20.0+0.5-0.5 *23.0+0.5-0.54.00-0.3 *14.0+0.5-0.5 *45.0+0.5-0.57345151880330 3.7 1.6±0.574452030********* 3.7 4.4±0.575452626********* 3.7 4.6±0.57645283742042080 3.78.4±0.5774538751450145040 3.729±0.5784538851650165035 3.733±0.5794538901800180035 3.736±0.580459555150140180 3.73±0.5814540851700170035 3.734±1824550601400140045 3.728±1834555601700170045 3.734±1844562712250225045 3.743±185471630180170180 3.7 3.6±0.5864808184038550 3.71±0.387481135140140200 3.73±1884812208075330 3.7 1.6±0.589481520100300 3.72±0.590481525130125220 3.7 2.6±0.591482020130125220 3.7 2.6±0.592501230********* 3.7 2.6±0.593501235150150200 3.73±0.594501430150150200 3.73±0.595501621110240 2.296501730********* 3.7 4.2±0.597501735260260130 3.7 5.2±0.598502025200200140 3.74±0.599502030250250120 3.75±0.510050203530030090 3.76±110150273035035080 3.77±110250303038038080 3.77.6±110350313045045080 3.79±110450304058058070 3.711.6±110550304872072045 3.714.4±110650344065065060 3.713±11075035621100110045 3.722±11085037591100110045 3.722±15.00-0.3 *37.0+0.5-0.5 *59.0+0.5-0.55.00-0.3 *30.0+0.5-0.5 *40.0+0.5-0.55.00-0.3 *30.0+0.5-0.5 *48.0+0.5-0.54.50-0.3 *9.0+0.5-0.5 *55.0+0.5-0.54.50-0.3 *38.0+0.5-0.5 *90.0+1.0-0.54.50-0.3 *15.0+0.5-0.5 *18.0+0.5-0.55.00-0.3 *34.0+0.5-0.5 *40.0+0.5-0.54.70-0.3 *16.0+0.5-0.5 *30.0+0.5-0.54.50-0.3 *55.0+0.5-0.5 *60.0+0.5-0.54.50-0.3 *41.5+0.5-0.5 *85.0+0.5-0.55.00-0.3 *12.0+0.5-0.5 *29.0+0.5-0.55.00-0.3 *12.0+0.5-0.5 *35.0+0.5-0.55.00-0.3 *30.0+0.5-0.5 *30.0+0.5-0.55.00-0.3 *31.0+0.5-0.5 *30.0+0.5-0.54.50-0.3 *20.0+0.5-0.5 *30.0+0.5-0.54.80-0.3 *11.0+0.5-0.5 *34.0+0.5-0.54.50-0.3 *62.0+0.5-0.5 *71.0+0.5-0.54.50-0.3 *50.0+0.5-0.5 *60.0+0.5-0.54.50-0.3 *26.0+0.5-0.5 *26.0+0.5-0.55.80-0.3 *8.0+0.5-0.5 *20.0+0.5-0.54.80-0.3 *11.5.0+0.5-0.5 *20.0+0.5-0.54.80-0.3 *15.0+0.5-0.5 *25.0+0.5-0.54.80-0.3 *20.0+0.5-0.5 *20.0+0.5-0.5尺寸(mm)5.00.1-0.3 *17.0+0.5-0.5 *34.0+0.5-0.54.80-0.3 *15.0+0.5-0.5 *20.0+0.5-0.54.50-0.3 *28.0+0.5-0.5 *37.0+0.5-0.54.50-0.3 *38.0+0.5-0.5 *85.0+0.5-0.54.50-0.3 *38.0+0.5-0.5 *75.0+0.5-0.55.00-0.3 *14.0+0.5-0.5 *29.0+0.5-0.55.00-0.3 *17.0+0.5-0.5 *30.0+0.5-0.5量产规格表序号型号标称容量（mAh）内阻（mΩ）电压（V）重量（g)厚×宽×高最小容量（mAh） 5.00-0.3 *35.0+0.5-0.5 *62.0+0.5-0.55.00-0.3 *16.0+0.5-0.5 *21.0+0.5-0.55.00-0.3 *20.0+0.5-0.5 *30.0+0.5-0.55.00-0.3 *20.0+0.5-0.5 *25.0+0.5-0.55.00-0.3 *27.0+0.5-0.5 *30.0+0.5-0.55.00-0.3 *20.0+0.5-0.5 *35.0+0.5-0.51095055601800180045 3.736±11105050681800180045 3.736±1111522022160160180 3.7 3.2±0.511252353355055070 3.711±11135350601800180045 3.736±1114551235170170170 3.7 3.4±111555345095095045 3.719±1116653759150045 3.730±111770242635035090 3.77±111870253252052070 3.710.4±1119701223130130200 3.7 2.6±0.512070255080080050 3.716±0.51217036381000100050 3.720±0.51227315158070330 3.7 1.6±0.5123751126180180180 3.7 3.6±0.512480102580330 3.7 1.6±0.5125801223160160200 3.7 3.2±0.512690186297597545 3.719.5±11273196509090300 3.7 2.3±0.5128552020170170200 3.7 3.4±0.51295551521400140045 3.728±113056223640090 3.78±1131582030300300100 3.76±113258313454070 3.710.8±1133601220100100300 3.72±1134601230170170180 3.7 3.4±0.5135601235200200150 3.74±1136601630240240120 3.7 4.8±1137601735300300120 3.76±1138601045220220130 3.8 4.4±1139602025240240120 3.7 4.8±11406032100A 170045 3.734±11416032100200035 3.738±11426034481000100060 3.720±1143602020170170200 3.7 3.4±114460204045045070 3.79±15.50-0.3 *34.0+0.5-0.5 *50.0+0.5-0.55.00-0.3 *50.0+0.5-0.5 *68.0+0.5-0.57.50-0.3 *12.0+0.0-0.5 *26.5+0.5-0.56.00-0.3 *34.0+0.5-0.5 *48.0+0.5-0.57.60-0.3 *12.0+0.5-0.5 *23.5+0.5-0.57.00.0-0.3 *36.0+0.5-0.5 *38.0+0.5-0.57.00.2-0.3 *12.0+0.5-0.5 *23.0+0.5-0.56.00-0.3 *20.0+0.5-0.5 *40.0+0.5-0.57.00.0-0.3 *25.0+0.5-0.5 *49.0+0.5-0.57.00.2-0.3 *15.0+0.5-0.5 *15.0+0.5-0.5重量（g)7.00-0.3 *24.0+0.5-0.5 *26.0+0.5-0.5电压（V）6.00-0.3 *20.0+0.5-0.5 *20.0+0.5-0.5序号最小容量（mAh） 6.00-0.3 *17.0+0.5-0.5 *35.0+0.5-0.5尺寸(mm)6.00-0.3 *12.0+0.5-0.5 *20.0+0.5-0.56.00-0.3 *32.0+0.5-0.5 *101+0.5-0.56.00-0.3 *32.0+0.5-0.5 *101+0.5-0.55.50-0.3 *51.0+0.5-0.5 *52.0+0.5-0.5型号 5.80-0.3 *20.0+0.5-0.5 *30.0+0.5-0.65.50-0.3 *12.0+0.5-0.5 *35.0+0.5-0.58.00-0.3 *10.0+0.5-0.5 *25+0.5-0.56.50-0.3 *37.0+0.5-0.5 *59.0+1.0-0.57.00-0.3 *25.0+0.5-0.5 *32.0+0.5-0.5内阻（mΩ）标称容量（mAh） 5.00-0.3 *55.0+0.5-0.5 *60.0+0.5-0.5量产规格表5.80-0.3 *31.0+0.5-0.5 *34.0+0.5-0.6厚×宽×高6.00-0.3 *10.0+0.8-0.5 *45.0+0.5-0.65.60-0.3 *22.5+0.5-0.5 *36.5+0.5-0.53.10-0.3 *9.6+0.5-0.5 *47.5+0.5-0.56.00-0.3 *16.0+0.5-0.5 *30.0+0.5-0.55.50-0.3 *20.0+0.5-0.5 *20.0+0.5-0.56.00-0.3 *12.0+0.5-0.5 *30.0+0.5-0.56.00-0.3 *12.0+0.5-0.5 *35.0+0.5-0.56.00-0.3 *20.0+0.5-0.5 *25.0+0.5-0.59.00-0.3 *18.0+0.5-0.5 *62.5+0.5-0.55.20-0.3 *20.0+0.5-0.5 *22.0+0.5-0.55.20-0.3 *35.0+0.5-0.5 *33.0+0.5-0.55.30-0.3 *50.0+0.5-0.5 *60.0+0.5-0.5145602425300300100 3.76±114660253240090 3.78±114760304890090045 3.718±1148653475175045 3.735±11494012154545500 3.7 1.1±0.51502314204040500 3.7 1.1±0.51514011299090270 3.72±0.51526011207575350 3.7 1.8±0.51536534611250125045 3.724.5±0.51543010305050430 3.7 1.4±0.51553510153030670 3.71±0.5156302029130130200 3.7 3.1±0.5157701837420400100 3.78.5±0.51584539661150105045 3.723±0.51594440841600160035 3.730±0.5159803450H 1100110035 4.128±1160481417H 5555170 4.1 1.5±0.2161551417H/601417H 7070160 4.12±0.2162400922H 40163701719H 140 4.1±0.2164701417H 9090140 4.1 2.4±0.2165452030H 15015090 4.1 4.5±0.3166502030H 20020070 4.1 5.3±0.3167501225H 7070150 4.12±0.3168602035H 30030055 4.17.6±0.3169603048H 60060035 4.115.5±0.5170383040H 35035050 4.19±0.5171401220H 4545250 4.1 1.6±0.5172703048H 80080025 4.119.5±0.5173523582H 1250125025 4.131±1174403048H 42042050 4.112±1175453048H 48048045 4.113±1176501723H 100100120 4.1 2.7±0.5177503465H 1000100025 4.126±1.04.50-0.3 *37.5+0.5-0.5 *83.50.5-0.5高倍率电池系列3.10-0.3 *20.0+0.5-0.5 *29.00.5-0.56.30-0.3 *33.5+0.5-0.5 *60.50.5-0.54.10-0.3 *10.5+0.5-0.5 *28.00.5-0.55.90-0.3 *10.5+0.5-0.5 *19.00.5-0.52.40-0.3 *14.0+0.5-0.5 *20.00.5-0.56.50-0.3 *34.0+0.5-0.5 *76+0.5-0.54.20-0.3 *12+0.5-0.5 *15.50.5-0.56.00-0.3 *30.0+0.5-0.5 *48.0+0.5-0.56.00-0.3 *25.0+0.5-0.5 *32+0.5-0.56.00-0.3 *24.0+0.5-0.5 *25.0+0.5-0.5量产规格表厚×宽×高4.50.2-0.3 *30.0+1.0-0.5 *48.0+1.0-0.5尺寸(mm)容量（mAh）8.00.2-0.3 *34.0+1.0-0.5 *50.0+1.0-0.57.00.2-0.3 *14.0+0.5-0.5 *18.0+0.5-0.55.00.2-0.3 *20.0+0.5-0.5 *30.0+0.5-0.56.00.20.3 *30.0+1.0-0.5 *48.0+1.0-0.53.80.20.3 *30.0+1.0-0.5 *40.0+1.0-0.54.00.2-0.3 *12.0+0.5-0.5 *20.0+0.5-0.55.20.2-0.3 *35.0+1.0-0.5 *82.0+1.0-0.54.00.2-0.3 *30.0+1.0-0.5 *48.0+1.0-0.5电压（V）重量（g)7.00.2-0.3 *30.0+1.0-0.5 *48.0+1.0-0.55.00.2-0.3 *17.0+1.0-0.5 *23.5+1.0-0.56.00.2-0.3 *20.0+1.0-0.5 *35.0+1.0-0.5序号型号容量（mAh）内阻（mΩ） 3.50-0.3 *9.5+0.5-0.5 *150.5-0.53.20-0.3 *9.5+0.5-0.5 *29.00.5-0.54.40-0.3 *39.5+0.5-0.5 *83.50.5-0.55.00.2-0.3 *34.0+1.0-0.5 *65+1.0-0.57.00-0.3 *18.0+0.5-0.5 *37.00.5-0.54.80-0.3 *14.0+0.5-0.5 *18.0+0.5-0.55.70.3-0.3 *14.0+0.5-0.5 *18.0+0.5-0.54.50.2-0.3 *12.0+0.5-0.5 *25.0+0.5-0.54.50-0.3 *20.0+0.5-0.5 *30.0+0.5-0.5178502025H 16016090 4.14±0.5版 本制定日期页 次179601719H 100100120 4.1 2.7±0.5180601717H 9090130 4.1 2.4±0.3181653562H 1100110025 4.127±1.0182701224H 100100140 3.7 2.5±0.3183702535H 45045045 3.712.5±0.5184483462H 85085025 3.722±0.5185553462H 95095025 3.723±0.5186703465H 1300130020 3.731±0.5187852040H 50050045 3.715±0.518875400H 15015090 3.74±0.5189581417H 7070145 3.7 2.06±0.319080600H 28028080 3.7 5.7±0.519180500H 21021080 3.7 4.8±0.519280400H 19019080 3.7 3.8±0.519375500H 17017090 3.74±0.519470350H 100100110 3.7 2.5±0.5195651723H 130±0.5196601723H 13013090 3.7 3.3±0.319775400H 120120110 3.7 3.6±0.3198551723H 120120100 3.7 3.0±0.3199903048H 20011500H 36038075 3.78.0±0.32011850020218650P 20318650204505068A 1550155035 3.729±1205535060A 1550155035 3.729±120550344335 3.70±15.30.2-0.3 *50.0+0.5-0.5 *60.0+0.50-0.5审 核制 定刘勇备注：规格表中产品内容仅供参考,详细内容以具体的产品规格书为准!※ 聚合物电芯的尺寸和规格可以按客户的要求定做※ 厚度不同（小于6mm）、长宽相同的电芯，不需另外开模※ 客户要求的电池容量若高于上述的标称容量，则要具体讨论，有颜色部分为新增型号，核 准 5.00.2-0.3 *50.0+0.5-0.5 *68.0+0.50-0.55.30.2-0.3 *50.0+0.5-0.5 *60.0+0.50-0.57.00.2-0.3 *25.0+1.0-0.5 *35+1.0-0.56.00.2-0.3 *17.0+1.0-0.5 *23.5+1.0-0.57.00.2-0.3 *34.0+1.0-0.5 *65.0+1.0-0.55.50.2-0.3 *34.0+1.0-0.5 *62.0+1.0-0.55.00.2-0.3 *34.0+1.0-0.5 *62.0+1.0-0.5深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY TECHNOLOGY CO., LTD.内阻（mΩ） 5.00.2-0.3 *20.0+1.0-0.5 *25.0+1.0-0.56.50.2-0.3 *35.0+1.0-0.5 *62+1.0-0.57.00.2-0.3 *12.0+1.0-0.5 *25+1.0-0.57.80.2-0.3 *50.0+1.0-0.56.00.2-0.3 *17.0+1.0-0.5 *20.0+1.0-0.56.00.2-0.3 *17.0+1.0-0.5 *18+1.0-0.57.80.2-0.3 *60.0+1.0-0.57.30.2-0.3 *40.0+1.0-0.56.80.2-0.3 *35.0+1.0-0.55.50.2-0.3 *17.0+1.0-0.5 *23.0+1.0-0.57.30.2-0.3 *50.0+1.0-0.5其他系列电芯7.80.2-0.3 *40.0+1.0-0.510.30.2-0.3 *50.0+1.0-0.58.30.2-0.3 *20.0+1.0-0.5 *40.0+1.0-0.57.30.2-0.3 *40.0+1.0-0.55.80.2-0.3 *14.0+1.0-0.5 *17.0+1.0-0.5A 2009-12-09PAGE 6 OF 6量产规格表电压（V）重量（g)厚×宽×高序号型号标称容量（mAh）最小容量（mAh）尺寸(mm)。