量能科技圆柱18650锂电池-2200mAh产品规格书
18650单电芯规格书
18650单电芯规格书BATTERY CO., LTD. DOC NO.: QR-WI-733-003-002/A REV. : APAGE: 1 of 8Specification Approval Sheet (cylinder Cell) 产品规格确认书（圆柱电池）Model/型号：ZZ18650Capacity/容量：1500mAhVoltage/电压：3.7V制定（Prepared By）审核（CheckedBy）批准（ApprovedBy）DOC NO.: QR-WI-733-003-002/A REV. : APAGE: 2 of 81.0基本特性Basic performance型号Model BJ18650P 外壳材质Can Material 镀镍钢Nickel-plated 标称容量NominalCapacity，（0.2C5A）1300mAh额定电压Nominal 3.70V 充电截止电压Max 4.20 V 放电终止电压 2.80V 最大充电电流Max.Charge Current1C5A标准持续放电流10C5A最大瞬间放电电流Max. Discharge Curent20 C5A电池最大直径（光壳）18.5电池最大高度（光壳）66mm 电池重量(Approx.) 约36g 内阻（Max, at 1000Hz.）≤16mΩ充电方法Charge 标准0.2C5A×快速 1 C5A×操作温度Operating Temperature 充电Charge0℃～45℃放电Discharge-20℃～60℃贮存Storage-10℃～45℃2.0 外形图figure2.1结构图Structure3.0 主要放电曲线Mainly capability graphBJ18650P-1300mAh 15C Discharge Cruve BJ18650P-1300mAh 1C Charge CruveBJ18650P-1300mAh 13C Cycle Life BJ18650P-1300mAh -20℃Discharge CruveDOC NO.: QR-WI-733-003-002/A REV. : APAGE: 3 of 84.0 电池性能Characteristic若没有特别说明，电池在做各项试验前，均需在86KPa～106 KPa大气压，环境温度20℃±5℃，相对湿度为45％～75％的条件下，以0.2C5A恒流放电至终止电压2.8V，并在收到产品两周内进行以下试验。
BFN18650F21(2200mAh)中英文
保定风帆新能源有限公司Baoding Fengfan New Energy Co.,Ltd.高能量圆柱型电池High Capacity Cylindrical Li-ion BatteryBFN18650F21-2200mAh编制Compile审核Audit批准Authoriz e2007-06-23发布Issue2007-06-23实施Execute地址：中国河北省保定市高开区鲁岗路199号Add:No.199Lugang Road of High Technology Z one,Baoding City,Hebei Provice,China 电话Tel：+863123327796传真Tel：+8631233277881.适用范围Scope of Application本规格书规定了保定风帆新能源有限公司向客户提供的BFN18650F21(2200mAh)圆柱型锂离子电池的技术参数及测试标准。
本型号电池适用于笔记本电脑、对讲机、便携式DVD，仪器仪表、音响设备、航模、玩具、摄像机、数码照相机等电子设备。
This specification gives the technical parameters and testing standard of BFN18650F21(2200mAh)provided by Baoding Fengfan New Energy Co.,Ltd..This kind of battery is suitable for notebook,interphone,portable DVD,instruments and meters,sonic equipment,aeromodelling,electric tools,vidicons,digital cameras.2.种类型号Kind&Type2.1种类Kind：圆柱型锂离子二次电池Rechargeable Cylindrical Lithium-ion Battery2.2型号Type：BFN18650F21-2200mAh3.参考标准Reference Standa rds此规范参考GB/T18287-2000、UL1642及IEC61960—1：2000等技术标准规范编制。
友创伟业 YCY Li-ion 18650 3.7V 2200mAh电池说明书
SpecificationSeries系列:圆柱锂离子电池Pack Type组合类型:电芯+保护板+引线Model No.型号:YCY Li-ion186503.7V2200mAhCapacity容量:2200mAhVersion版本:01Customer Approve客户确认Company Name客户名称Dept.部门Signature签名Date日期QA Dept品质R&D Dept研发Approved批准1.SCOPE使用范围This specification is applied to the reference battery in this specification and manufactured by Shenzhen YCY Technology Co.,Ltd本说明书适用于本书中所提及的深圳市友创伟业科技有限公司生产的锂电池。
12Max.Continuous Discharge Current最大连续放电电流 1.5CmA 13Operation Temperature Range操作温度Charge 充电:0~45℃60±25%R.H.Discharge 放电:-20~60℃14Storable Temperature Range储存温度1year 一年-20~25℃60±25%R.H.3months 三个月-20~40℃1week 一周-20~60℃15Weight 重量Approx 约:48.0gBattery pack 电池包16Dimension尺寸Height :64.9±0.2mm (Max.50.1mm )Battery CELL电芯Diameter :18.3±0.1mm (Max.18.4mm )3.Performance And Test Conditions3.1Standard Test Conditions 标准测试条件Test should be conducted with new batteries within one week after shipment from our factory and the batterys shall not be cycled more than five times before the test.Unless otherwise defined,test and measurement shall be done under temperature of 20±5℃and relative humidity of 45~85%.If it is judged that the test results are not affected by such conditions,the tests may be conducted at temperature 15~30℃and humidity 25~85%RH.测试必须使用出厂时间不超过一个星期的新电池，且未进行过五次以上的充放电循环。
18650（3600mah）规格书（标准书）
18650（3600mah）规格书（标准书）文件名称产品型号修改记录产品型号目录1 适用范围 (4)2 引用标准 (4)3 定义........................................ .. (4)3.1 手机用电池battery for cellular phone ..... . (4) 3.2 充电限制电压 limited charge voltage ............... .. (4)3.3 额定容量 rated capacity ........................... .. (4)3.4 标称电压 nominal voltage (4)3.5 终止电压 cut-off voltage (4)4 技术参数 (4)4.1 电芯参数表 (4)4.2 主要参数表 (5)4.3 保护板参数表 (5)5 要求 (5)5.1 测试条件 (5)5.2 测量仪表与设备要求 (6)5.3 外观 (6)5.4 充电制式 (6)5.5 20℃放电性能 (6)5.6 高温性能 (6)5.7 低温性能 (6)5.8 荷电保持能力 (6)5.9 循环寿命 (7)5.10 环境适应性 (7)5.11 安全保护性能 (7)5.12 电池完全完全充电后内阻 (8)6 运输、贮存 (8)7 安全规程及使用说明 (8)8 特殊要求 (8)9 PCB原理图，电芯基本特性及外形图 (9)10 电芯充放电曲线图11 成品电池尺寸图产品型号1 适用范围本规格书适用于可充电锂离子电池产品的定义、要求、测试方法、质量评定程序及标志、包装、运输、贮存。
用户请务必严格按照规格书中的测试或使用方法进行测试或使用，如对表中的测试项目或测试方法有异议，请与供应方协商解决2 引用标准下列标准所包含的条文，通过在本规范中引用而构成为本规范的条文。
GB/T 2828-1987 逐批检查计数抽样程序及抽样表（适用于连续批的检查）GB/T 2829-1987 周期检查计数抽样程序及抽样表（适用于生产过程稳定性的检查）GB/T 2900.11-1988 蓄电池名词术语3 定义本规范采用GB/T 2900.11 中规定的术语和下列定义。
E18650C22-2200mAh规格书-0007-A-0(纯钴)
1Preface 前言Maximum allowable charge andHigh-LowNO. 序号ITEM 项目6 Package picture包装图片Small box big box pallet(50pcs cells in a small box, 6 small boxes in a big box)7 Guaranteed and product liability 保质期及产品责任Guaranteed from the date of delivery is the first six months保质期是从出厂日期开始起6个月8Warning and cautions in handling the lithium-ion cell电芯使用时警告事项及注意事项To prevent the possibility of the cell from leaking, heating, explosion, please observe the following precautions:为防止电芯可能发生泄露，发热，爆炸，请注意以下预防措施：Don’t immerse the cell in water.严禁将电芯浸入水中。
保存不用时，应放置在阴凉干燥的环境中。
Caution小心If the cell leaks and the electrolyte get into your eyes, don’t wipe eyes, instead, thoroughly rinse the版本V ersionThis spec manual is the enterprise standard of ZNB, without authorization, any pirate or circulation is prohibited. Page 11 of 11。
三星18650 2200mAh规格书
SPECIFICATION OF PRODUCTfor Lithium-ion Rechargeable CellModel : ICR18650-22FMAug, 2008Samsung SDI Co., Ltd.Battery Business DivisionHistory of Revisions1. ScopeThis product specification has been prepared to specify the rechargeable lithium-ion cell ('cell') to be supplied to the customer by Samsung SDI Co., Ltd.2. Description and Model2.1 Description Cell (lithium-ion rechargeable cell)2.2 Model ICR18650-22FM3. Nominal SpecificationsNote (1): If the cell is kept as ex-factory status(50% of charge),the capacity recovery rate is more than 80%.4. Outline DimensionsSee the attachment(Fig. 1)5. AppearanceThere shall be no such defects as scratch, rust, discoloration, leakage whichmay adversely affect commercial value of the cell.6. Standard Test Conditions6.1 Environmental ConditionsUnless otherwise specified, all tests stated in this specification areconducted at temperature 25±5℃and humidity 65±20%.6.2 Measuring Equipment(1) Ammeter and VoltmeterThe ammeter and voltmeter should have an accuracy of the grade 0.5 or higher.(2) Slide caliperThe slide caliper should have 0.05 mm scale.(3) Impedance meterThe impedance meter with AC 1kHz should be used.7. Characteristics7.1 Standard ChargeThis "Standard Charge" means charging the cell with charge current1100mA and constant voltage 4.2V at 25℃for 3hours.7.2 Standard Discharge CapacityThe standard discharge capacity is the initial discharge capacity of the cell, which is measured with discharge current of 440mA with 2.75V cut-off at 25℃within 1 hour after the Standard charge.Standard Discharge Capacity ≥2150mAh7.3 Initial internal impedanceInitial internal impedance measured at AC 1kHz after Standard charge.Initial internal impedance ≤100mΩ7.4 Temperature Dependence of Discharge CapacityDischarge capacity comparison at each temperature, measured with dischargeconstant current 1100mA and 2.75V cut-off with follow temperature after the standard charging at 25℃.Note: If charge temperature and discharge temperature is not the same,the interval for temperature change is 3 hours.Percentage as an index of the Standard discharge capacity(=2150mAh) is 100%.7.5 Temperature Dependence of Charge CapacityCapacity comparison at each temperature, measured with dischargeconstant current 1000mA and 2.75V cut-off at 25℃after the Standard charge isas follow temperature.Note: If charge temperature and discharge temperature is not the same,the interval for temperature change is 3 hours.Percentage as an index of the Standard discharge capacity(=2150mAh) is 100%.7.6 Charge Rate CapabilitiesDischarge capacity is measured with constant current 440mA and 2.75V cut-offafter the cell is charged with 4.2V as follows.Note: Percentage as an index of the capacity at 25℃(=2150mAh) is 100%.7.7 Discharge Rate CapabilitiesDischarge capacity is measured with the various currents in under table and 2.75Vcut-off after the standard charge.Note: Percentage as an index of the capacity at 25℃(=2150mAh) is 100%.7.8 Cycle LifeEach cycle is an interval between the charge (charge current 1760mA) and thedischarge (discharge current 2200mA) with 2.75V cut-off. Capacityafter 299cycles and plus 1 day, measured under the same condition in 7.2Capacity ≥1500mAh7.9 Storage CharacteristicsCapacity after storage for 30days at 25℃after the Standard charged,measured with discharge current 1100mA with 2.75V cut-off at 25℃.Capacity retention(after the storage) ≥1720mAh7.10 Status of the cell as of ex-factoryThe cell should be shipped in 50% charged state.8. Mechanical Characteristics8.1 Drop TestTest method: Cell(as of shipment or full charged) drop onto the oak-board(thickness:≥30mm) from 4feet height at a random direction 6 times.Criteria: No leakage8.2 Vibration TestTest method: Cell(as of shipment) is vibrated along 2 mutuallyperpendicular axes with total excursion of 1.6mm and withfrequency cycling between 10Hz and 55Hz by 1Hz/min.Criteria: No leakage9. Safety10.1 Overcharge TestTest method: To charge the standard charged cell with 12V and 2200mA at 25℃for 2.5 hours.Criteria: No fire, and no explosion.10.2 External Short-circuit TestTest method: To short-circuit the standard charged cell by connecting positive and negative terminal by less than 50mΩwire for 3 hours.Criteria: No fire, and no explosion.10.3 Reverse Charge TestTest method: To charge reversely the standard charged cell with charge current2200mA for 2.5 hours.Criteria: No fire, and no explosion.10.4 Heating TestTest method: To heat the standard charged cell at heating rate of 5℃per minute up to 130℃and keep the cell in oven for 60 minutes.Criteria: No fire, and no explosion.10. WarrantySamsung SDI will be responsible for replacing the cell against defects or poor workmanship for 15month from the date of shipping. Any other problems caused by malfunction of the equipment or unsuitable use of the cell are not under this warranty.The warranty set forth in proper use, handling conditions described above,and excludes in the case of a defect which is not related to manufacturing of the cell.11. Others12.1 Storage for a long timeIf the cell is kept for a long time(3months or more), It is strongly recommendedthat the cell is preserved at dry and low-temperature.12.2 OtherAny matters that specifications does not have, should be conferred withbetween the both parties.12. PackagingSee Fig.2,Package DrawingFig. 1 Outline Dimensions of ICR18650-22FMUnit : mm Max. 18.4 Max. 65.0Fig 2. Package DrawingProper Use and Handling of Lithium Ion CellsSee before using lithium-ion cellSupplied bySamsung SDIEM1. GeneralThis document has been prepared to describe the appropriate cautions and prohibitions, which the customer should take or employ when the customer usesand handles the lithium ion cell to be manufactured and supplied by Samsung SDIEM in order to obtain optimum performance and safety.2. Charging2.1 Charging currentCharging current should be less than maximum charge current specified inthe product specification.2.2 Charging voltageCharging should be done by voltage less than that specified inthe product specification.2.3 Charging timeContinuous charging under appropriate voltage does not cause any loss ofcharacteristics. However, the charge timer is recommended to be installedfrom a safety consideration, which shuts off further charging at time specifiedin the product specification.2.4 Charging temperatureThe cell should be charged within a range of specified temperatures inthe product specification.2.5 Reverse chargingThe cell should be connected, confirming that its poles are correctly aligned.Inverse charging should be strictly prohibited. If the cell is connectedimproperly, it may be damaged.3. Discharging3.1 Discharging3.1.1 The cell should be discharged at less than maximum discharge currentspecified in the product specification.3.2 Discharging temperature3.2.1 The cell should be discharged within a range of temperatures specified inthe product specification.3.2.2 Otherwise, it may cause loss of characteristics.3.3 Over-discharging3.3.1 The system should be equipped with a device to prevent further dischargingexceeding discharging cut-off voltage specified in the productspecification.(over-discharging)3.3.2 Over-discharging may cause loss of performance, characteristics, ofbattery function.3.3.3 Over-discharging may occur by self-discharge if the battery is left fora very long time without any use.3.3.4 The charger should be equipped with a device to detect cell voltage and todetermine recharging procedures.4. Storage4.1 Storage conditions4.1.1 The cell should be stored within a range of temperatures specifiedin the product specification.4.1.2 Otherwise, it may cause loss of characteristics, leakage and/or rust.4.2 Long-term storage4.2.1 The cell should be used within a short period after charging becauselong-term storage may cause loss of capacity by self-discharging.4.2.2. If long-term storage is necessary, the cell should be stored at lowervoltage within a range specified in the product specification, becausestorage at higher voltage may cause loss of characteristics.5. Cycle life5.1 Cycle life performance5.1.1 The cell can be charged/discharged repeatedly up to times specified inthe produce specification with a certain level of capacity also specifiedin the product specification.5.1.2 Cycle life may be determined by conditions of charging, discharging,operating temperature and/or storage.6. Design of System6.1 Connection between the cell and the battery6.1.1 The cell should not be soldered directly with leads. Namely, the cellshould be welded with leads on its terminal and then be soldered withwire or leads to soldered lead.6.1.2 Otherwise, it may cause damage of component, such as separator andinsulator, by heat generation.6.2 Positioning the battery in the System6.2.1 The battery should be positioned as possible as far from heat sourcesand high temperature components.6.2.2 Otherwise, it may cause loss of characteristics.6.3 Mechanical shock protection of the battery6.3.1 The battery should be equipped with appropriate shock absorbers in order tominimize shock.6.3.2 Otherwise, it may cause shape distortion, leakage, heat generationand/or rupture.6.4 Short-circuit protection of the cell6.4.1 The cell is equipped with an insulating sleeve to protect short-circuit whichmay occur during transportation, battery assembly and /or systemoperation.6.4.2 If the cell sleeve is damaged by some causes such as outside impact,it may cause short-circuit with some wiring inside the battery.6.5 Connection between the battery and charger/system6.5.1 The battery should be designed to be connected only to the specifiedcharger and system.6.5.2 A reverse connection of the battery, even in the specified system,should be avoided by employing special battery design such asa special terminals.7. Battery Pack Assembly7.1 Prohibition of usage of damaged cell7.1.1 The cell should be inspected visually before battery assembly.7.1.2 The cell should not be used if sleeve-damage, can-distortion and/orelectrolyte-smell is detected.7.2 Transportation7.2.1 If the cell is necessary to transport to order place, such as thebattery manufacturer, careful precautions should be taken to avoiddamage of cell.8. Others8.1 Disassembly8.1.1 The cell should not be dismantled from the battery pack.8.1.2 Internal short-circuit caused by disassembly may lead to heat generationand/or venting.8.1.3 When the electrolyte is coming in contact with the skin or eyes,wash immediately with fresh water and seek medical advice.8.2 Short-circuiting8.2.1 Short-circuit results in very high current which leads to heat generation.8.2.2 An appropriate circuitry should be employed to protect accidentalshort-circuiting.8.3 Incineration8.3.1 Incinerating and disposing of the cell in fire are strictly prohibited,because it may cause rupture.8.4 Immersion8.4.1 Soaking the cell in water is strictly prohibited, because it may causemelt of components to damaged to functions.8.5 Mixing use8.5.1 Different types of cell, or same types but different manufacturer's cellmay lead to cell rupture or damage to system due to the differentcharacteristics of cell.8.6 Battery disposal8.6.1 Although the cell contains no environmentally hazardous component,such as lead or cadmium. the battery should be disposed according tothe local regulations when it is disposed.8.6.2 The cell should be disposed with a discharged state to avoid heat generationby an inadvertent short-circuit.8.7 Caution - The Battery used in this device may present a risk of fire or chemical burn ifmistreated. Do not disassemble, heat above 100℃or incinerate. Replacebattery with Samsung SDI battery only. Use of another battery may present a riskof fire or explosion. Dispose of used battery promptly. Keep away from children.Do not disassemble and do not dispose of in fire.8.8 AttachedSystem Pack Quality Guideline8-8-1 The battery pack’s consumption current.- Sleep Mode: Under 250uA.- Shut Down Mode: Under 10uA (under 2.5V).8-8-2 SOC 0%- Any bank voltage in SOC 0% of Pack should be higher than 3.0V.(Discharging Cut-off Voltage)8-8-3 Operating Charging Voltage of a cell.- Normal operating voltage of cell is 4.20V.- Max operating voltage of cell is 4.25V.8-8-4 No continuous charge- Charge cut-off condition : Cut-off Current is higher than 1/20C(Charging method: CC-CV)- Initial recharging condition : Remaining Capacity is lower than 90% or Voltageis lower than 4.10V8-8-5 Pre-charging function- Pre-charge function should be implemented to prevent abnormal high ratecharging after deep discharge.- Pre-charging condition :Operation: less than 3.0VCharging current : Under 150mA/Cell.(Continuous)Pre-charge stop (Normal Charge Start) : All cells reach 3.0V8-8-6 Cell voltage monitoring system.- The system (Charger or Pack) should equip a device to monitor each cellvoltage and to stop charging if a cell imbalance happened.8-8-7 The battery pack should have warning system for over temperature, over voltage, over current, and unexpected events would be harm to system. If battery facesharsh condition such as over temperature, Battery pack should control FET-offdirectly.8-8-8 Mechanical guides.- PCBA and Cell stack should have heat insulation material between them. (Suchas plastic barrier which is giving air isolation or non-thermal conductivematerial.)- B+ and B- wire connection should not be crossed each other. Do not make wirewhich had the voltage difference more than 4.0V get together.- The material such as double sided tape and rubber which are used in batterypack should be verified for its flammabilityHandling Precaution and Prohibitions of Lithium Ion & Lithium Ion PolymerRechargeable Cells and BatteriesInaccurate handling of lithium ion and lithium ion polymer rechargeable battery may cause leakage, heat, smoke, an explosion, or fire.This could cause deterioration of performance or failure. Please be sure to follow instructions carefully.1.1 StorageStore the battery at low temperature (below 20℃is recommended), low humidity, no dust and no corrosive gas atmosphere.1.2 Safety precaution and prohibitionsTo assure product safety, describe the following precautions in the instruction manual of theapplication.[ Danger!]■Electrical misusageUse dedicated charger.Use or charge the battery only in the dedicated application.Don't charge the battery by an electric outlet directly or a cigarette lighter charger.Don't charge the battery reversely.■Environmental misusageDon't leave the battery near the fire or a heated source.Don't throw the battery into the fire.Don't leave, charge or use the battery in a car or similar place where inside of temperature may be over 60℃.Don't immerse, throw, wet the battery in water / seawater.■othersDon't fold the battery cased with laminated film such as pouch and Polymer.Don't store the battery in a pocket or a bag together with metallic objects such as keys, necklaces, hairpins, coins, or screws.Don't short circuit (+) and (-) terminals with metallic object intentionally.Don't pierce the battery with a sharp object such as a needle, screw drivers.Don't heat partial area of the battery with heated objects such as soldering iron.Don't hit with heavy objects such as a hammer, weight.Don't step on the battery and throw or drop the battery on the hard floor to avoid mechanical hock.Don't disassemble the battery or modify the battery design including electric circuit.Don't solder on the battery directly.Don't use seriously scared or deformed battery.Don't put the battery into a microwave oven, dryer ,or high-pressure container.Don't use or assemble the battery with other makers' batteries, different types and/or models of batteries such as dry batteries, nickel-metal hydride batteries, or nickel-cadmium batteries.Don't use or assemble old and new batteries together.[ Warning! ]Stop charging the battery if charging isn't completed within the specified time.Stop using the battery if the battery becomes abnormally hot, order, discoloration, deformation, orabnormal conditions is detected during use, charge, or storage.Keep away from fire immediately when leakage or foul odors are detected. If liquid leaks onto your skin or cloths, wash well with fresh water immediately.If liquid leaking from the battery gets into your eyes, don't rub your eyes and wash them with clean water and go to see a doctor immediately.If the terminals of the battery become dirty, wipe with a dry cloth before using the battery.The battery can be used within the following temperature ranges. Don't exceed these ranges.Charge temperature ranges : 0℃~ 45℃Discharge Temperature ranges : -20℃~ 60℃Store the battery at temperature below 60℃Cover terminals with proper insulating tape before disposal.[ Caution! ]■Electrical misusageBattery must be charge with constant current-constant voltage (CC/CV).Charge current must be controlled by specified value in Cell specification.Cut-off Voltage of charging must be 4.2V.Charger must stop charging battery by detecting either charging time or cur rent specified in Cell’s specification.Discharge current must be controlled by specified value in Cell’s specification.Cut-off Voltage of discharging must be over 2.5V.■othersKeep the battery away from babies and children to avoid any accidents such as swallow.If younger children use the battery, their guardians should explain the proper handling method and precaution before using.Before using the battery, be sure to read the user's manual and precaution of it's handling.Before using charger, be sure to read the user's manual of the charger.Before installing and removing the battery from application, be sure to read user's manual of the application.Replace the battery when using time of battery becomes much shorter than usual.Cover terminals with insulating tape before proper disposal.If the battery is needed to be stored for an long period, battery should be removed from the application and stored in a place where humidity and temperature are low.While the battery is charged, used and stored, keep it away from object materials with static electric chargers.Safety Handling Procedure for the Transporter■Quarantine : Packages that are crushed, punctured or torn open to reveal contents should not be transported. Such packages should be isolated until the shipper has been consulted,provided instructions and, if appropriate, arranged to have the product inspected andrepacked.■Spilled Product : In the event that damage to packaging results in the release of cells or batteries, the spilled products should be promptly collected and segregated and the shippershould be contacted for instructions.Design of positioning the battery pack in application and charger To prevent the deterioration of the battery performance caused by heat, battery shall be positioned away from the area where heat is generated in the application and the charger.Design of the Battery PackBe sure adopting proper safe device such as PTC specified type or model in Cell Specification.If you intend to adopt different safety device which is not specified in Cell Specification, please contact Samsung SDI to investigate any potential safety problem.Be sure designing 2nd protective devices such as PTC & PCM at the same time to protect Celljust in case one protective device is fault.Please contact following offices when you need any help including safety concerns.Samsung SDI Emergency Contact Information■Samsung SDI Headquarter.575 Shin-dong, Youngtong-gu, Suwon, Kyunggi-doTel:(+82)31-210-7114 Fax:(+82)31-8006-3689■Samsung SDI Chonan factory.508, Sungsung-Dong, Chonan City, Chungchongnam-Do, KoreaTel:(+82)41-560-3669 Fax:(+82)41-560-3697■Samsung SDI America office.18600 Broadwick Street Rancho Dominguez CA 90220Tel:(+1)310-900-5205 Fax:(+1)310-537-1033■Samsung SDI Taiwan office.Rm. 3010, 30F., 333, Keelung Rd. Sec. 1, Taipei, TaiwanTel:(+886)2-2728-8469 Fax:(+886)2-2728-8480。
H18650CIL-2400mAh通用规格书A02
锂离子电芯规格书SpecificationForLithium-ion Rechargeable Cell电芯型号:H18650CILCell Type:H18650CILDocument No P/PR03/PB-D-H18650CIL Revised date2015.11.13 Version A/02Pages9 Approved Checked Designed孙新科Contents目录1Preface前言2Definition定义2.1Rated capacity标称容量2.2Standard charge method标准充电方式2.3Standard discharge method标准放电方式3Cell type and dimension电芯型号及尺寸3.1Description and model电芯说明及型号3.2Cell dimension电芯尺寸4Cell characteristics电芯特性5Technical requirements技术要求5.1Cell usage conditions电芯使用环境5.2Cell testing conditions电芯实验环境5.3Requirement of the testing equipment测量仪表要求5.4Electrochemical characteristics电化学特性5.5Environmental characteristics and safety characteristics环境适应性能与安全性能6Package picture包装图片7Shipment出货8Warranty质量保证9Storage and Shipment Requirement存储及运输要求10Warning and cautions in handling the lithium-ion cell电芯使用时警告事项及注意事项11The restriction of the use of hazardous substances有害物质控制要求12Contact information联系方式13Version history修订履历1Preface前言This specification describes the type and dimension,performance,technical characteristics,warning and caution of the lithium ion rechargeable cell.The specification only applies to H18650CIL cell supplied by Shenzhen BAK Power Battery Co.,Ltd.本标准描述了圆柱型锂离子电芯的外型尺寸、特性、技术要求及注意事项。
圆柱型锂离子电芯规格书PRODUCTSPECIFICATION
圆柱型锂离子电芯规格书PRODUCT SPECIFICATIONCylindrical Lithium-ion Cell电芯型号: LR1865AMSignature 签名Date 日期Company Name ：公 司 名 称Customer Approval 客 户 认 同Company Stamp ：公 司 印 章Prepared By首 发Checked By 核 对 QA 质量确认 Approved By 批 准Model: LR1865AM适用范围The product specification describes the requirement of the Cylindrical Lithium-ion Cell to be supplied to the customer by Tianjin Lishen Battery J/S Co., Ltd. Should there be any additional information required by the customer, customer are advised to contact Tianjin Lishen Battery J/S Co., Ltd..本规格书规定了由天津力神电池股份有限公司生产的圆柱型锂离子电芯的技术要求，测试方法及注意事项，如需获取本规格书以外的技术要求，请与力神电池股份有限公司联系相关事宜。
2 DESCRIPTION AND MODEL 型号及说明2.1 Description 说明 : Cylindrical Lithium Ion Cell 圆柱型锂离子电芯2.2 Model 电芯型号 : LR1865AM3 GENERAL SPECIFICATIONS 常规指标3.1 Nominal Capacity 标称容量 1100mAh (at 0.55A Discharge 0.55A放电)Minimum Capacity 最低容量 1000mAh (at 0.55A Discharge 0.55A 放电)3.2 Charging Voltage 充电电压 3.60V±0.05V3.3 Average working Voltage 标称电压 3.20V@0.55A3.4 Standard Charge Method 标准充电方式 Constant Current and Constant Voltage (CC/CV)先恒流充电再恒压充电Current 电流 0.55AVoltage 电压 3.6VEnd Current 终止电流 20mA±5mA3.5 Maximum Charge Current 最大充电电流 1.5A3.6 Standard Discharge 标准放电方式 Constant Current 恒流放电 (CC)Current 电流 0.55AEnd Voltage 终止电压 2.0V3.7 Maximum Discharge Current 最大放电电流 25A3.8 Cycle Life 循环寿命 1000th cycle >60% of 4th Capacity (1.5A/10A at 25℃)1000 次循环>60%第四次循环容量 (25℃，1.5A充电/10A放电) 750th cycle >60% of 4th Capacity (1.5A/10A at 45℃)750 次循环>60%第四次循环容量 (45℃，1.5A充电/10A放电) 500th cycle >60% of 4th Capacity (1.5A/10A at 60℃)500 次循环>60%第四次循环容量 (60℃，1.5A充电/10A放电)外形尺寸（单位：mm）Dimension: Diameter 18.4mm (max), Height 65.1mm (max). Refer to the attached drawing 3.电芯尺寸：直径 18.4mm（最大），高度65.15mm（最大），参考附图3。
规格书SZNS mAh
REMARK（备注） Standard.charge/discharge
标准充放电 Standard.charge/discharge
标准充放电 Average 平均值
Constant current 恒流 Constant voltage 恒压 End current 截止电流 Constant current 恒流 Constant voltage 恒压 End current 截止电流
Max. Charge Voltage 最大充电电压
Max.charge current 最大充电电流
Standard Discharge （Refer to 4.2） 标准放电
Fast Discharge (refer to 4.3) 快速放电（参照 4.3） Max.discharge current 最大放电电流 Approx Weight 大约重量 Internal resistance 内阻 Diameter 直径
电池 按 4.3 的测试方法进行充放电 300 周，其中 1 周包
含 1 个充电和放电。
Cells shall be charged per 4.1 at 25℃±2 ℃ and discharge per
4.2 at the following temperatures
在 25℃±2℃ 按照 4.1 放式充满电，在如下的温度下按 4.2 放式放
深圳市卓能新能源股份有限公司
锂离子电芯规格书
Specification For
Lithium-ion Rechargeable Cell
电芯型号：SZNS18650-2200（带 PTC） Cell Type：SZNS18650-2200（with PTC）
圆柱18650锂电规格 容量 详细资料
各种18650锂电池规格和容量容量松下-S O N Y锂电池的容量判断方法松下锂电池的容量判断方法蓝色c g r186501200m a h粉红色c g r186501350m a h黄色c g r18650h m1600m a h橙色c g r18650h g1800m a h紫色c g r18650H G L1800m a h浅绿色c g r18650a2000m a h`浅红色c g r18650c b2060m a h浅蓝色c g r18650c2200m a h锂电池容量标识蓝色的是1350m a hg21550m a h g30p1700m a h1800m a h g41950m a h2100m a h g62200m a hP a n a s o n i c C G R18650A F2050m A h型号 :P A N A S O N I C C G R18650A F标称容量 :2050m A h标称电压 :3.6V直径 :M a x18.6m m高度 :M a x65.2m m重量 :42gP a n a s o n i c C G R18650C2200m A h标称容量: 2150mAh标称电压: 3.6 V直径: Max 18.6mm高度: Max 65.2mm重量: 44.5 gP a n a s o n i c C G R18650C F2300m A h标称容量 :2250m A h标称电压 :3.6V直径 :M a x18.6m m高度 :M a x65.2m m重量 :45gP a n a s o n i c C G R18650D2400m A h标称容量 :2350m A h标称电压 :3.6V直径 :M a x18.6m m高度 :M a x65.2m m重量 :45gP a n a s o n i c C G R18650D A2450m A h 标称容量 :2450m A h标称电压 :3.6V直径 :M a x18.6m m高度 :M a x65.2m m重量 :45.5gP a n a s o n i c C G R18650E2550m A h标称容量 :2550m A h标称电压 :3.6V直径 :M a x18.6m m高度 :M a x65.2m m重量 :46.5gLG ICR18650P2 2000mAh型号: ICR 18650P2 2000mAh标称容量: 2000mAh(标准充放电)直径: 18.3±0.1 mm高度: 64.9±0.2 mm大概重量: 46.7 gLG ICR18650S2 2200mAh标称容量:2200m A h最低容量:2150m A h直径:18.3±0.1m m(M a x18.4m m)高度:64.8±0.2m m(M a x65.1m m)重量 (T y p i c a l)大约:44.5gLG ICR18650A2 2350mAh型号: LG ICR18650A2标称容量: 2350mAh(标准充放电)最小容量: 2300mAh直径: 18.3±0.1 mm (Max 18.4 mm)高度: 64.8±0.2 mm (Max 65.1 mm)大概重量: 46.5 gLG ICR18650A3 2430mAh型号 :L G I C R18650A3标称容量 :2430m A h最低容量 :2380m A h直径 :18.3±0.1m m(M a x18.4m m)高度 :64.8±0.2m m(M a x65.1m m)重量 :约 46.1gLG ICR18650B2 2600mAh型号: LG-18650-2600标称容量: 2600mAh(标准充放电)直径: 18.3±0.1 mm (Max 18.4 mm)高度: 64.9±0.2 mm (Max 65.1 mm)大概重量: 46.5 g-o U n2c p E w w w.6s q.n e t摩利（MOLICEL）18650产地：加拿大Model: ICR18650H容量: 2200mAhNominal V oltage: 3.75V重量: 46.1gM O L I C E L I C R18650J2400m A h标称容量: 2400mAh标称电压: 3.75V重量: 47g直径: 18.24 mm高度: 65.0 mmS A M S U N G I C R18650-202000m A h直径 :18.25m m高度 :65.0m m重量 :44gS A M S U N G I C R18650-222200m A h标称容量:2200m A h直径:18.25m m高度:65.0m m重量:46gS A M S U N G I C R18650-242400m A h标称容量:2400m A h直径:18.25m m高度:65.0m m重量:48gS A M S U N G I C R18650-262600m A h标称容量: 2600mAh重量(大约): 48gS A N Y O U R18650V1900m A h标称容量: 1900mAh重量: Max.46.0gS A N Y O U R18650H1900m A h标称容量: 1900mAh重量: Max.46.0gS A N Y O U R18650F H2000m A h型号: UR18650FH标称容量: 2000mAhS A N Y O U R18650F2200m A h标称电压 :3.7V重量: Max.46.5g直径: Max.18.1 mm高度: Max.64.8 mm三洋18650 SANYO 2400MAH绿头三洋18650 SANYO 2200MAH红头三洋18650 SANYO 2000MAH白头SONY2200MAH日本万胜18650电池，容量1800mah/2000mahB A K18650C42200m A h（比克电池）标称容量: 2200mAh标称电压: 3.0 V内部阻抗: < 70 m直径: 18.2±0.2 mm (Max 18.4 mm)高度: 64.80±0.3 mm (Max 65.1 mm)大概重量: 48 gS A P H I O N I F R18650E可充电锂离子电芯（磷酸铁锂型锂离子电池）充电电压：3.65V标准充电（最高4.2V）标称工作电压：3.2V@0.2C标称容量：1400mAh@0.2C标准放电方法：280mA@0.2C最大连续放电：2.8A(2C)最大瞬间放电：（30秒）5.6A(4C)放电截至电压：2.5V充电时间：标准充电2.5小时充电方法：恒流0.5C电流充电至3.65V，然后恒压充电直至电流小于0.05C循环寿命特性：到90%容量大于1000次循环工作温度：Charge O-C ~ 45-C; Discharge: -10-C ~ 50-C储存温度：400C~ 500C湿度：相对湿度5-95%电芯重量：38±2g电池尺寸：长：65±0.3mm;直径：18±0.3mmS A P H I O N I F R18650P可充电锂离子电芯（磷酸铁锂型锂离子电池）充电电压：3.65V标准充电标称工作电压：3.2V@1C标称容量：1100mAh@1C放电截至电压：2.0V充电时间：标准充电2.5小时工作温度：-10°C to 50°C储存温度：-40°C to +50°C电芯重量：39g电池尺寸：长：65±0.3mm;直径：18±0.3mm部分S O N Y锂电参数表C O K E C Y L I ND R:圆柱形，炭正极型号———电压—容量—长度———直径————重量U S14500—3.6—500——50.5———14.3————19U S14650—3.6—700——64.9———14.9————25U S17670—3.6—1270—66.8———16.9————38U S18650—3.6—1500—65.1———18.4————42U S26650—3.6—2800—65.4———26.3————83C O K E P R I S M:方形，炭正极h*L+c n.w h型号———电压—容量———长度——宽度————厚度——重量U S083488—3.6—850———7.9———33.7————48.1——35U S093448—3.6—950———8.6———34—————48.2——39U S103463—3.6—1650——10————34—————62.8——58G R A P H I T E C Y L I N D R:圆柱形，石墨正极型号————电压—容量——长度———直径————重量U S14430G—3.7——460——42.8———14—————17U S14500G—3.7——580——49.6———14.1————18U S14650G—3.7——780——64.9———14—————24U S17570G—3.7——1270——66.8———16.9————39U S18650G—3.7——1500——65.1———18.4————42G R A P H I T E P R I S M:方形，石墨正极型号————电压——容量——长度——宽度————厚度——重量0 U S083448G—3.7——620——6.3———29.5————47.8——25。
规格书SZNS18650-2200mAh
电池 按 4.3 的测试方法进行充放电 300 周，其中 1 周包
含 1 个充电和放电。
Cells shall be charged per 4.1 at 25℃±2 ℃ and discharge per
4.2 at the following temperatures
在 25℃±2℃ 按照 4.1 放式充满电，在如下的温度下按 4.2 放式放
深圳市卓能新能源股份有限公司
锂离子电芯规格书
Specification For
Lithium-ion Rechargeable Cell
电芯型号：SZNS18650-2200（带 PTC） Cell Type：SZNS18650-2200（with PTC）
Document NO Version Designed
Max. Charge Voltage 最大充电电压
Max.charge current 最大充电电流
Standard Discharge （Refer to 4.2） 标准放电
Fast Discharge (refer to 4.3) 快速放电（参照 4.3） Max.discharge current 最大放电电流 Approx Weight 大约重量 Internal resistance 内阻 Diameter 直径
标准放电方式： “Standard Discharge” shall consist of discharging at a constant current of 0.2C (440mA) to 2.75V. Discharging is to be performed at 25℃±2 ℃ unless otherwise noted (such as capacity versus temperature ) 指在 25℃±2 ℃环境下，0.2C（440mA）恒流放电至 2.75V。 4.3 Fast charge/discharge method 快速充放电方式 Tested at 25℃±2 ℃ Cell shall be charged at constant current of 0.5C(1100mA) to 4.20Vwith end current of 22mA. Cells shall be discharge at constant current of 0.5C(1100mA) to 2.75V. Cells are to rest 10 minutes after charge and 20minutes after discharge. 在 25℃±2 ℃，0.5C(1100mA)恒流恒压充电到 4.20V，截止电流为 22mA，搁置 10min，然后 0.5C(1100mA)放电到 2.75V，搁置 20min。
2200mah电芯规格书
锂离子二次电池
产品规格书
型号:IMR18650P22
制定： 审核： 批准：
产品规格书
IMR18650P22
编号：XB-S-102 版次：A/0
一、范围
本规格书描述了由赣州雄博新能源科技有限公司提供的锂离子二次电池 IMR18650P22 的有关参考要求。
二பைடு நூலகம்电池类型与型号
1、电池类型：锂离子二次电池。 2、电池型号：IMR18650P22。
编号：XB-S-102 版次：A/0
七、 安全性能
项 1. 短路 目 测试方法 标 准 电池通过导线短路正负极，导线总电阻不大于 50 不漏液、不冒烟、 m，当电池温度下降到比峰值低约 10℃时，结束 不爆炸；电池外 试验。 部温度不高于 150℃ 将完全充电的电池连接电芯正负极于一恒流恒压 不起火、爆炸 电源， 调节电流至 1C5A 电压为 5V， 然后对电芯进 行充电，直到电芯电压达到最大输出电压后，再持 续充电 7h。 试验过程中监视电芯温度变化， 当电芯 温度下降到比峰值低约 10℃，结束试验。 电池以 0.2C5A 放电至 2.75V， 然后在正负极之间接 不起火、不爆炸 上 30Ω电阻，放置 24h，观察电芯外观。 将 完 全 充 电 电 池 放 置 于 热 箱 中 ， 温 度 以 不起火、不爆炸 5℃±2℃/min 的速率升至 130℃±2℃并保温 30min。 将完全充电电池放置于冲击台上，1 根 18.5mm 的 不起火、不爆炸 棒十字交叉放在样品的国心位置上，将 9.1kg 重锤 自 61cm 高度跌落在样品上。 将完全充电电池放置在两个平面间进行挤压， 挤压 不起火、不爆炸 力通过一直径为 1.25 英寸(32mm)活塞的液压活塞 施加，挤压持续直至压力达到 17.2Mpa，施加的挤 压力为 13KN， 当达到最大压力即可卸压。 圆柱型和 方形电芯在进行挤压试验时， 应使其纵轴方向与挤 压平面平行。
单体电芯18650-2200-3.7V 规格书
Temperature: 20℃~25℃
Relative Humidity:60%±25% R.H.
4.3CellElectrical characteristics/电气特性
No
Items/项目
Test Method and Condition/测试方法及条件
容量保持
≥80%
4
Temperature Dependence ofdischargecapacity（放电温度特性）
Cells shall be charged per3.3.1anddischarged@0.2C5A to3.0volts.Except to be discharged at temperatures per Table3. Cells shall be stored for3hours at the test temperature prior to discharging and then shall be discharged at the test temperature. The capacity of a cell at each temperature shall be compared to the capacity achieved at 23ºC and the percentage shall be calculated. .
本说明书只适用于描述本规格书中相关的产品以及优贝特科技有限公司提供的电池。
2Model/型号：18650
3Cell Specification/电芯产品规格
No.
Items/项目
Specifications/规格
Remark
备注
韩国LG化学有限公司锂离子电池ICR18650 S3 2200mAh说明书
A (Max. 18.40 mm)
Method of Cell Printing
LG
Company
Name
I
Year
A
Complex
A
Capacity
site
Code
290 J17
Date Code Lot Id
S3
Model
1865
Model
Name
Size
6 A1
Line
Lot Serial
1st Line: LG Chem, Ochang 2 Factory, Capacity(0~2400mAh), S3 model, 18650 Size 2nd Line: 2009, 290th Date, J17 Lot, Line No=6, Lot serial=A1
Prepared
LGC MED/BTC
Approved
CLhGecCkedMED/BTC
Kim, Yong Chan Ryu, Duk Hyun
PRODUCT SPECIFICATION
CONFIDENTIAL
Document No.
Date
Rev
LRB-PS-CY2200_S3_Rev8 2011-02-01
3. Appearance and Dimension
3.1 Appearance
There shall be no such defects as deep scratch, crack, rust, discoloration or leakage, which may
adversely affect the commercial value of the cell.
N18650-2200-2P3S+引线 规格书
客户名称：产品类型电池型号电芯类型电芯型号2P3S11.1V4400mAh Li-ion NCM18650-2200制造商：制订/日期审核/日期批准/日期2015-3-16客户确认：审核/日期批准/日期制造商：宁波德朗能锂电池科技有限公司地址：浙江省奉化市高新技术开发区南山北路1号电话：86－0574-********传真：86－0574-********目录版本更改历史记录更改时间更改内容00/002015-3-16新版发行1.适用范围2.引用标准3.电气特性4.成品电池尺寸图5.主要物料6.可靠性测试规范7.常规性测试规范8.运输9.贮存10.包装和标志11.使用说明和安全规程1、适用范围：本规格书描述电池之标称参数、电气特性、安全性能、环境适应性及其实验和判定、使用说明和安全规程、质量评定及包装、标志、贮存、运输等。
2．引用标准：GB/T18287-2000中华人民共和国蜂窝电话用锂离子电池总规范。
3．电气特性：序号内容参数备注1标称电压10.8V2标称容量4400mAh0.2C 完全充电后用0.2C放电至截止电压的容量。
3充电电压 4.25V±0.025V 4内阻200mΩ（Max）5充电方式C.C/C.V.恒流/恒压方式恒流/恒压视电池电压转换6充电方式1.标准充电0.2C充电电流880mA2.快速充电1C充电电流4400mA7充电时间标准充电8Hours 快速充电2Hours8最大充电电流4400mA9最大放电电流4400mA10放电截止电压 2.75V11过充电保护电压 4.25±0.025V12过充回复电压 4.15±0.05V13过充电保护侦测延时时间400ms(Typical)14过放电保护电压 2.7±0.08V15过放电保护回复 3.0±0.1V16过电流保护4A～8A17输出短路保护保护后撤销短路负载回复18工作消耗电流50uA(Max)19过电流保护侦测延时时间200mS(Max)20过放电保护侦测延时时间100mS(Max)21输出短路保护侦测延时时间50uS(Max)22工作温度充电时0~45℃放电时-20~60℃23贮存温度-5℃-35℃推荐（25±5℃）贮存时应充电至容量的40%~50%24ID电阻10K±5％25喷码内容11.1V4400mAh2015-03-12(年月日按生产时间而更变）26静电测试±8KV27循环寿命300cycle28重量约272g 4．成品电池尺寸图：A尺寸40.15±0.2mmB尺寸55.7±0.2mmC尺寸68.5±0.5mmD尺寸10±1cm5．主要物料：材料规格描述数量备注厂商锂电芯NCM18650-2206PCS DLGPCB板PCM-137A11PCS保护IC8254AA1PCSMOS管44092PCS6．可靠性测试规范：6.1测试条件:除非另有规定,本规范中各项试验应在试验的标准大气条件下进行:温度:-5℃-35℃推荐（25±5℃）相对湿度：≦75%大气压强：86KP—106KP6.2测量仪表与设备的要求：6.2.1测量电压的仪表准确度应不低于0.5级,内阻应不小于10KΩ/V6.2.2测量电流的仪表准确度应不低于0.5级.6.2.3测量时间的仪表准确度不低于±0.1%.6.2.4测量温度的仪表准确度不低于±0.5℃.6.2.5恒流源的电流恒定可调,在充电或放电过程中,其电流变化应在±1%范围内.6.2.6恒压源的电压可调,其电压变化范围为±0.5%.6.2.7尺寸测量仪的准确度不低于0.02mm,量程为200mm.6.2.8称量质量的仪器感量不低于0.1g,秤量为1.5Kg..组号检验项目标准测试方法1高温性能电池在55±2℃，用1C5A放电时间不少于51min,电池外观无变形、无爆裂.完全充电后置于55±2℃,2h用1C5A放电2低温性能电池在-20±2℃，用0.2C5A放电时间不少于3h,电池外观无变形、无爆裂.完全充电后置于-20±2℃,16-24h用0.2CA放电,结束后将电池置于20±5℃条件下搁置2h,观察电池外观.3荷电保持能力放电时间不少于4.25h 完全充电后,在25±5℃条件下,将电开路搁置28d,再0.2C5A放电.4恒定湿热性能电池外观应无明显变形、锈蚀、冒烟或爆炸，放电时间不低于36min.完全充电后,在40±2℃,相对湿度为90%-95%的恒温恒湿条件下搁置48h后,再取出放在20±5℃条件下搁置2h再以1C5A放电.5振动电池外观应无明显变形、锈蚀、冒烟或爆炸，电池电压不低于3.6V.完全充电后,以0.38mm振幅作谐振10Hz~30Hz的频率,将电池安装在振动台上,设置好X.Y.Z三个方向上从扫频速率为1oct/min,循还扫频振动30min6碰撞电池外观应无明显变形、锈蚀、冒烟或爆炸，电池电压不低于3.6V.振动试验结束后,将电池平均按X.Y.Z三个互相垂直轴向上,设置脉冲峰值加速度为100m/s2,每分钟碰撞次数40~80,脉冲持续时间16ms,碰撞次数1000±10.7自由跌落电池应不漏液,不冒烟,不爆炸,能插入蜂窝电话,锁扣可靠;放电时间不低于51min.碰撞试验结束后,将样品电池从1000mm高处自由跌落于水泥地面上的18-20mm厚的硬木板上,从X,Y,Z正负六个方向每个方向1次.试验结束后,能完全充放电不少于3个循还.8过充电保护性能电池应不爆炸,不起火,不冒烟或漏液.电池完全充电结束后,用恒流恒压源给电池加载8h,恒流恒源设定为2倍标称电压,电流设定为2C5A9过放电保护性能电池应不爆炸,不起火,不冒烟或漏液.电池在环境温度20±5℃的条件下,以0.2C5A放电至终止电压后,外接30Ω负载电阻放电24h.10短路保护性能电池应不爆炸,不起火,不冒烟或漏液;瞬时充电后电池电压不低于10.8V.电池完全充电后,将正负极用0.1Ω电阻短路1h,将正负极断开后,电池以1C5A电流瞬时充电5S.11重物冲击不起火,不爆炸,电池允许变形电池置于冲击台上,将10KG重锤自1M高度自由下落冲击已固定在夹具中的电池(电池的面积最大的面应与台面垂直),12热冲击不起火,不爆炸电池置于热箱中,温度以5℃±2℃/min,升至130℃±2℃并保持30min.13过充电不起火,不爆炸本项试验应在拆除电池保护线路板后进行.将接有电热偶的电池置于通风橱中,连接正负极于一恒流恒压电源,调节电流至3C5A,电压为3*4.8V 然后对电池充电直到电压为3*4.8V,电流降到接近0A,监视温度变化,当电池温度下降到比峰值低约10℃时,试验结束.14短路不起火,不爆炸,电池外部温度不高于150℃.本项试验应在拆除电池保护线路板后进行.将接有电热偶的电池置于通风橱中,短路其正负极(线路总电阻不大于50mΩ),监视温度变化,当电池温度下降到比峰值低约10℃时,试验结束.15循环寿命循环寿命不低于300次.电池循环寿命试验应在20℃±5℃,以1CA充电,当电池端电压达到充电限制电压时,改为恒压充电,直到充电电流小于或等于20mA,停止充电搁置0.5h-1h,然后以1C5A电流放电至终止电压,放电结束后,搁置0.5-1h,再进行下一个循还,直至连续两次放电时间小于36min.则认为寿命终止.16贮存电池贮存12个月,经完全充电后,0.2C5A,放电时间不小于4h.进行贮存试验的电池应选自生产日期到试验日期不足3个月的电池,电池贮存前应按完全充电的40%~50%的容量,在环境温度20℃±5℃,相对湿度45%-85%的环境中贮存,贮存期满后,电池按完全充放电制进行充放电.7．常规性测试规范：7.1除非另有规定,本规范中各项试验应在试验的标准大气条件下进行:温度:-5℃-35℃推荐（25±5℃）相对湿度：≦75%大气压强：86KP—106KP组号检验项目测试方式标准备注1外观目测与实配电池外表面应清洁，无机械损伤,触点无锈蚀,必须有产品标示,与蜂窝电话配合,开机应工作正常，锁扣可靠20.2C5A放电性能完全充电后放电时间不应低于5H3安全保护性能过充电保护性能电池完全充电后,用恒流恒压给电池加载8H,电压设定为7.4V,电流设定为2C5A电池应不爆炸,不起火,不冒烟或漏液.过放电保护性能以0.2C5A放电至终止电压后,外接30Ω负载放电24H.电池应不爆炸,不起火,不冒烟或漏液.短路保护以0.2C5A充电，当电池端电压达到充电限制电压时，改为恒压充电，直到充电电流小于或等于0.01C5A，最长充电时间不大于8h，充电结束后将正负极用0.1Ω电阻器短路1h，池应不爆炸,不起火,不冒烟或漏液.将正负极断开，电池以1C5A电流瞬时充电5s后用电压表测量电池电压，电池电压应不低于10.8V。
1Li-ion18650C-2200mAh 锂离子圆柱电池说明书
Li-ion Cylindrical Battery Specification锂离子圆柱电池说明书MODEL型号: 1Li-ion18650CNominal Capacity标称容量: 2200mAhCustomer客户:Total Page文件页数：9Registered 编制Checked审核Approved批准林育张年根2017.04.202017.04.20Customer Approve客户确认Dept. 部门Signature签名Date日期QA Dept品质R&D Dept研发Approved批准Add: No.1 Factory,Oriebtal Hi-tech Park ,Qiaoxiang Rd,ShenZhen ,China 地址：深圳市南山区侨香西路高发东方科技园1#厂房P.C.: 518053 邮编：518053Tel：+86-755-26756070 Fax：+86-755 26755329http：// E-mail:**************.cnContent目录1.MODIFIED LIST (3)2 .Scope 适用范围 (4)3.Initial Dimension初始尺寸 (4)4.Specification 产品规格 (5)5 General Performance 常规性能 (6)6 Environment Performance 环境性能 (6)7 Safe Characteristic 安全性能 (6)8. CAUTIONS IN USE使用警告 (7)9. Battery operation instruction电池操作说明 (8)10. Period of Warranty保质期 (9)11. Other The Chemical Reaction其它化学反应 (9)12.Note: 备注 (9)1. MODIFIED LIST修订履历Product Modified Record List产品变更履历表Revision 版本Date日期Mark标记Modified content变更内容Approved by批准A1 201-04-202 .Scope 适用范围This specification describes the basic performance, technical requirement, testing method, warning and caution of the Li- ionCylindrical rechargeable battery .The specification only applies to Shenzhen Kunteng Co., Ltd.本标准规定了圆柱锂离子可充电池的基本性能、技术要求、测试方法及注意事项，本标准只适用于深圳市昆腾实业有限公司。
HYLC18650-2200mAh圆柱低温锂电池规格书
Operating
10
temperature
工作温度
11
Storage temperature 储存温度
440mA
2.5V
Charging： 0℃~45℃
充电：
0℃~45℃
Discharging：-40℃~60℃
放电：
-40℃~60℃
-10℃~ +45℃
12
Cell weight 电芯重量
Approx：44.2g 约：44.2g
2) Put the cell into -40±2℃ high temp oven for 4 hours and discharge at 440mA for 5 mins and then change to 220mA to 2.5V at this temperature.
Initial capacity 初始容量 70%
3 Temperature 高温放电
discharge at 0.2C CC to 2.5V at the high temperature. 在 初始容量 90% 60±2℃的高温箱中恒温 2h，在该温度下 0.2C 恒流放电至 2.5V。
1) Standard Charge 标准充电
4
Discharging at Low Temperature
Initial Capacity voltage after standard charge.
2
初始容量
该容量是指标准充电后，0.2C 放电至 3V 截止电压所放
出的容量。
Criteria ≥ 2.2Ah
Discharging at 1) Standard Charge 标准充电
High
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Specification for Li-ion Rechargeable cylindrical battery圆柱锂离子电池规格书MODEL/型号: 18650-2200mAh1.0 SPECIFICATIONS基本特性2.0 CONFIGURATION外形图DiameterHeight3.0 The definitions of some nomenclatures of this specification标准中的一些术语的定义：（1）Standard Charge: Charge with current 0.5C5A to limit charge voltage 4.2V under the condition of 25℃±5℃surrounding temperature, then change to charge with constant voltage till the current less than or equal to 0.01 C5A.标准充电：在环境温度20℃±5℃的条件下，以0.5C5A充电，当电池端电压达到充电限制电压4.2V时，改为恒压充电，直到充电电流小于或等于0.01C5A后停止充电（2）Initial State: The initial appearance, open-circuit voltage and internal resistance of battery.初始状态：电池的初始外观、开路电压、交流内阻。
（3）Final State: The final appearance, open-circuit voltage and internal resistance of battery.最终状态：电池的最终外观、开路电压、交流内阻。
（4）Residual Capacity: After a specific testing program, the first discharge capacity of battery.剩余容量：电池经过特定的检测程序后的首次放电容量。
（5）Recovery capacity: After a specific testing program,and through the repeatedly charging and discharging to the recovery state, then the discharge capacity of battery.恢复容量：电池经过特定的检测程序后，通过反复充放电使状态恢复后的放电容量。
（6）0.5 C5A /1 C5A (0.5 C5A /0.5 C5A, 0.5 C5A /0.2 C5A）：Charge at 0.5C5A to limit charge voltage 4.2V, then change to charge with constant voltage until the current less than or equal to 0.01 C5A, rest for 5 min, then discharge at 1C5A(0.5 C5A, 0.2C5A) to 2.75V cut-off.0.5C/1C（0.5C/0.5C、0.5C/0.2C）：以0.5C5A充电，当电池端电压达到充电限制电压4.2V时，转为恒压充电，直到充电电流小于或等于0.01C5A停止充电，充电完成后，搁置5min，再以1C5A（0.5 C5A、0.2C5A）恒流放电至终止电压3.00V。
4.0 CHARACTERISTICS电池性能4.1 Electrochemical Performance电化学性能4.1.1 Discharge Characteristics (Room Temperature) 常温放电性能Test Method: At standard atmospheric pressure, ambient temperature 25℃±5℃, relative humidity 45％～80％（The following if no specific instructions are all in these conditions, according to this charging ways）, after 0.5 C5A standard charged, rest for 15min and then discharge at 0.2C5A, 0.5C5A, 1C5A and 2C5A to the discharge cut-off voltage 2.75V respectively. Charge/discharge cycle can be conducted for 3 times before meeting the Standards（the same below）.测试方法：在1标准大气压，环境温度25℃±5℃，相对湿度为45％～80％的条件下，电池0.5C标准充电后（以下若没有特别说明，均在此条件下放置，皆按此充电方式），搁置10min，分别以0.2C5A、0.5C5A、1C5A、2C5A进行放电至下限电压2.75V，循环三次，当有一次达到标准，即达到标准要求（下同）。
Standard：Discharge capacity / Nominal capacity *100％A）0.2C5A ≥100％B）0.5C5A ≥98％C）1C5A ≥95％D）2C5A ≥85％The charging and discharging curves must be smooth标准：放电容量/标称容量×100％A）0.2C5A ≥100％B）0.5C5A ≥98％C）1C5A ≥95％D）2C5A ≥85％充放电曲线应平稳光滑4.1.2 Normal Storage常温荷电保持能力Test Method: Tested the initial condition and initial capacity of battery. Store for 28 days after standard charged, tested the final condition of battery. Then discharge at 0.5C5A to the discharge cut-off voltage 2.75V, tested the residual capacity of battery. 0.5C5A /0.5 C5A tested the recovery capacity of battery.Charge/discharge cycle can be conducted for3 times before meeting the Standards.测试方法：测量电池的初始状态和初始容量，电池标准充电后，开路放置30天，测量电池最终状态；以0.5C5A 放电至2.75V，测量电池的剩余容量；0.5C/0.5C测量电池的恢复容量。
可循环三次，当有一次达到标准，即达到标准要求。
Standard：Residual capacity ≥ Nominal capacity *85％Recovery capacity ≥ Nominal capacity *90％Diminishing rate of open-circuit voltage≤3％Increasing rate of internal resistance≤20％标准：剩余容量≥标称容量*85％恢复容量≥标称容量*90％开路电压减小率≤3％内阻增加率≤20％4.1.3 Cycle Life循环寿命Test Method: Measured the initial condition and initial capacity of battery. Then conduct 0.5C5A/1C5A 150th cycle measured the final condition of battery. Or conduct 0.5C5A/0.5C5A 150th cycle measured the final condition of battery.测试方法：测量电池的初始状态和初始容量，进行0.5C/1C循环，150次后测量电池的最终状态；或0.5C/0.5C 循环300次后测量电池的最终状态。
Standard：Residual capacity ≥ Nominal capacity *80％标准：容量≥标称容量*80％4.1.4 Long Time Storage贮存性能Test Method: Charged to the voltage of 3.80±0.02V, before storage, measured the initial condition and initial capacity of battery. Store for 3 months, 6 months, 12 months at room temperature, measured the final condition of battery. Then conduct 0.5 C5A /0.2 C5A cycle for 3 times to record the discharge time of the battery.测试方法：测量电池的初始容量，电池充电至3.80±0.02V后，测量电池存储前的初始状态，分别室温贮存3个月、6个月、12个月后，测量电池的最终状态,然后以0.5C/0.2C循环3次记录电池的放电时间。
Standard：The discharge time of 0.2C5A:Storage 3 months of battery≥4.5h；Storage 6 months of battery≥4.25h；Storage 12 months of battery≥4h.标准：0.2C5A放电时间贮存3个月的电池≥4.5h；贮存6个月的电池≥4.25h；贮存12个月的电池≥4h。
4.2 Safety Performance安全性能4.2.1 Overcharge过充性能Test Method: Standard charge. Charge at 1 C5A to 10V, then change to charge with constant voltage till the current less than or equal to 0.01 C5A. Observe the variation of the bat tery’s appearance and temperature.测试方法：电池标准充电后，测量电池的初始状态, 保证电池状态正常（下同）,以1 C5A电流充电至4.8V,然后转恒压充电至截至电流0.01C5A时终止, 观察电池的温度及外观变化。