LED 5050硬灯条规格书
5050高亮灯珠规格书
XQD-L5DZGL-SPC1 ● Customer:Technical Data Sheet ---- Preliminary Luminosity Full Color/Single Color LED(5050 )Contents1. Features2. Applications3. Package outline dimension4. Absolute maximum ratings5. Electrical-optical characteristics6. Typical electro-optical characteristics curves7. Tapping specifications8. Package method9. BIN code description10. BIN range11. Reliability test items and conditions12. Precautions for use13. Hazard substance analysisCustomer confirm Approved by Issued ByXQD-L5DZGL-SPC1※Features.White package with black surface..Optical indicator..Colorless clear window..Ideal for backlight and light pipe application..Interior reflector..Wide viewing angle..Suitable for vapor-phase reflow, infrared reflow and wave solder processes. .Computable with automatic placement equipment..Pb-free..The product itself will remain within RoHS compliant version※Applications:.Amusement equipment..Information boards..Flashlight for digital camera of cellular phone.Device Selection GuideChip Emiteed Resin Color Type MaterialR A1GaInP Brilliant RedXQD-L5DZGL-SPC1 G InGaN Brilliant GreenB InGaN Blue※ →Package Outline Dimension:Notes: All dimensions in mm tolerance is ±0.1mm unless otherwise noted.XQD-L5DZGL-SPC1 ※Absolute Maximum Ratings(Ta=25 ℃)XQD-L5DZGL-SPC1 ※Electrical-optical characteristics(Ta=25 ℃)Note:1. Tolerance of Luminous Intensity: ±10%2. Tolerance of Dominant Wavelength: ±1nm3. Tolerance of Forward Voltage: ±0.1V※BIN rangeLuminous intensity (tolerance is ±10%@ If= 60 60mA): mA):Note:1. Tolerance of Luminous Intensity: ±10%2. Tolerance of Dominant Wavelength:±1nmXQD-L5DZGL-SPC1※Reliability test items and conditions:The reliability of products shall be satisfied with items listed below. Confidence level：90%LTPD：10%XQD-L5DZGL-SPC1 Typical Electro-Optical Characteristics Curves (G)XQD-L5DZGL-SPC1Typical Electro-Optical Characteristics Curves (R)XQD-L5DZGL-SPC1Typical Electro-Optical Characteristics Curves (B)XQD-L5DZGL-SPC1※Precautions for use ::1. Over-current-proofCustomer must apply resistors for protection; otherwise slight voltage shift will cause big current change (Burn out will happen).2. Storage2.1 Do not open moisture proof bag before the products are ready to use.2.2 Before opening the package: The LEDs should be kept at 30 or less and 90%RH or less.2.3 After opening the package: The LED's floor life is 1 year under 30 or less and 60% RH orless. If unused LEDs remain, it should be stored in moisture proof packages.2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded theXQD-L5DZGL-SPC1 storage time, baking treatment should be performed using the following conditions.Baking treatment: 60±5 fo℃ r 24 hours.3. Soldering Condition3.1 Pb-free solder temperature profile3.2 Reflow soldering should not be done more than twotimes.3.3 When soldering, do not put stress on the LEDs during heating.3.4 After soldering, do not warp the circuit board.Note:a) Reflow soldering should not be done more than two times.b) Don’t put stres s on the LEDs when soldering.c) Don’t warp the circuit board before it have been returned to normal ambientXQD-L5DZGL-SPC1 TemperatureTime2min, Max..5℃ /Sec. Max.4℃/Sec. Max.5 Sec. Max.260℃ Max.160~180℃TemperatureTTTTime ime120~180 sec.Preheat245 ±5℃ within 5 sec.Soldering heat Max. 260 ℃120~150℃conditions after soldering.Loaded quantity: 1000 pcs/reel※Package Method:(unit:mm)XQD-L5DZGL-SPC1Note: Tolerance unless mentioned is ±0.1mm,Unit=mm。
5050全彩5050RGB5050全彩RGBH5规格书
●Customer:Technical Data Sheet-PreliminaryLuminosity Full Color LED(5050)Contents1.Features2.Applications3.Package outline dimension4.Absolute maximum ratings5.Electrical-optical characteristics6.Typical electro-optical characteristics curves7.Tapping specifications8.Package method9.BIN code description10.BIN range11.Reliability test items and conditions12.Precautions for use13.Hazard substance analysisCustomer confirm ApprovedbyIssuedby※Features․White package with black surface.․Optical indicator.․Colorless clear window.․Ideal for backlight and light pipe application.․Interior reflector.․Wide viewing angle.․Suitable for vapor-phase reflow,infrared reflow andwave solder processes.․Computable with automatic placement equipment.․Pb-free.․The product itself will remain within RoHScompliant version※Applications:․Amusement equipment.․Information boards.․Flashlight for digital camera of cellular phone.Device Selection GuideChip Emiteed Resin Color Type MaterialR A1GaInP Brilliant RedG InGaN Brilliant GreenB InGaN Blue※→Package Outline Dimension:※Electrical-optical characteristics(Ta=25℃)Parameter Symbol Min.Typ.Max.Unit ConditionForward Voltage Vf R 1.8 2.0 2.6VI F=20mA G 2.8 3.1 3.7B 2.8 3.1 3.7Luminous Intensity Iv R---450---mcd G---1200---B---350---Dominant Wavelengthλd R617---630nm G517---530B462---475Viewing Angle2θ1/2---120---DegReverse Current I R-------10μA Vr=5V Junction Temperature Tj110------℃Electrostatic DischargeClsaaificationESD1500VNote:1.Tolerance of Luminous Intensity:±10%2.Tolerance of Dominant Wavelength:±1nm3.Tolerance of Forward Voltage:±0.1V4.Electrostatic Discharge Clsaaification R=G=B=1500V※BIN rangeLuminous intensity(tolerance is±10%@If=20mA):Symbol Bin Code Min Max.Unit ConditionIV R10300500mcd I F=20mA 11500700137001000G131000125014125015501515502000B1021030011300500Note:1.Tolerance of Luminous Intensity:±10%※Color Bin Limit(IF=20mA)Symbol Bin Code Min Max.Unit ConditionColor R1615620nM IF=20mA 26206253625630G451552055205256525530B446046554654706470475Note:1.Tolerance of Dominant Wavelength:±1nm※Reliability test items and conditions:The reliability of products shall be satisfied with items listed below.Confidence level：90%LTPD：10%No.Test Item Test Conditions Duration/Cycle Sample size Ac/Re 1Operation Life Ta=25℃,I F=20mA1000hrs220/12High TemperatureHigh HumidityTa=85℃/85%RH1000hrs220/13Thermal Shock H:+100℃30min∫10secL:-30℃30min100cycle220/14High TemperatureStorageTa=100℃1000hrs220/15Low TemperatureStorageTa=-40℃1000hrs220/16Temperature Cycle H:+100℃30min∫5minL:-30℃30min100cycle220/17High Humidity HeatLife Test60℃RH=90%IF=20mA1000hrs220/18ESD(HBM)1KV at1.5kΩ;100pf3Time220/1※Precautions for use :1.Over-current-proofCustomer must apply resistors for protection;otherwise slight voltage shift will cause big current change (Burn out will happen).2.Storage2.1Do not open moisture proof bag before the products are ready to use.2.2Before opening the package:The LEDs should be kept at 30or less and 90%RH or less.2.3After opening the package:The LED's floor life is 1year under 30or less and 60%RH orless.If unused LEDs remain,it should be stored in moisture proof packages.2.4If the moisture absorbent material (silica gel)has faded away or the LEDs have exceeded thestorage time,baking treatment should be performed using the following conditions.Baking treatment:60±5fo ℃r 24hours.3.Soldering Condition3.1Pb-free solder temperature profile3.2Reflow soldering should not be done more than two times.3.3When soldering,do not put stress on the LEDs during heating.3.4After soldering,do not warp the circuit board.Note:a)Reflow soldering should not be done more than two times.b)Don’t put stress on the LEDs when soldering.c)Don’t warp the circuit board before it have been returned to normal ambientconditions after soldering.TempTime2min, Max..5℃ /Sec. Max. 4℃/Sec. Max.5 Sec. Max.240℃ Max.160~180℃TempTime120~180 sec.Preheat 235 ±5℃ within 5 sec.Soldering heat Max. 240 ℃120~150℃H5---WENEN-H5050RGB*版本：A2Ver A page 11of 11Loaded quantity:1000pcs/reel ※Package Method:(unit:mm)。
LED硬灯条产品说明书
LED硬灯条产品说明书一、产品说明颜色:黄,白,暖白光工作电压: DC 24V灯珠分类：SMD5050(贴片5050灯珠)1、规格:5050每米40灯DC 24V 1M≤8 W；5050每米60灯DC 24V 1M≤12W ；5050每米72灯DC 12V 1M≤14.4 W；光源色温不同,光色也不同色温在3300K以下,光色偏红给以温暖的感觉；有稳重的气氛，温暖的感觉.，通称暖色温。
色温在 3000--6000K 为中间，人在此色调下无特别明显的视觉心理效果，有爽快的感觉；故称为“中性”色温色温超过 6000K ，光色偏蓝，给人以清冷的感觉，通称冷色温2、工艺类别NK---裸板（室内用）铝---滴胶（半防水，灯脚滴硅胶，工艺稍复杂）铝---全滴胶（防水，室外用，工艺稍复杂，适合室外复杂环境工作）产品特性1、采用散热性能好的铝基板或玻纤板作为载体，印制电路板，散热性能好，导电性强。
2、外壳为铝合金材料，散热性能好。
如果安装在室外，可根据客户要求把铝合金外壳氧化成跟楼体相同的颜色，不会因为安装灯具而影响楼体的美观。
3、采用防紫外线，抗老化的胶水全部密封，防水性能达到IP65。
4、一般应用于广告装饰、城市亮化、楼宇亮化、酒柜、珠宝展柜、天花暗槽等室内外照明以及装饰照明。
长度可按要求定做。
3、使用及注意：本产品为恒流低压12V，请接12V低压或购置变压开关电源；本品常规使用时，建议并联；当串联使用时，连接长度请勿超过电源最大功率的80%，以免电源超负载工作导致电源烧毁。
二、使用说明：1、接线说明：红、黄、蓝、绿、白单色防水软光条：产品引出两根电源线，一根是红色，一根是黑色，导线线径是22AWG，长度是150MM。
红色线接电源正级，黑色线接电源负极。
如果使用控制器控制，红色线接控制器输出的正级，黑色接控制器输出的负极。
2、安装说明：方案一：将灯条放到需要安装的位置上，取出螺丝，在灯条的两端堵头上上紧螺丝，固定好灯条，如左下图所示；方案二：卡件安装。
LC8805B-5050RGB规格书
1.2.运输及储存 Smart SMDLED采用防潮防静电铝箔袋包装，运输过程中避免挤压或刺穿包装袋，并做好必要的防静电防护措施 ，产品生产前，发现漏气及破损，请停止直接使用，并做必要的高温除湿后使用，产品在换料，贴装，成品出 货 ，安装过程中，应注意防止外力碰撞挤压 LED，造成外力损伤 LED 灯珠失效。 如生产前，已发现铝箔袋，拆封，破损，漏气请及时退回原厂重新除湿检测，绝不能上线使用。
4.封装尺寸图：
备注：所有尺寸标注单位为毫米公差为±0.15 毫米，除特别标注外。
文件编号：SPC-TOP- A/20701
PAGE: 2nd
深圳市丽创光电有限公司
Shenzhen Lictron Co.,LTD
5.引脚图及功能描述：
序号 1 2 3 4
符号 GND DIN DOUT VDD
引脚 地线或电源负端
PRODUCT NO: QUANTITY: LOT NO: DATE:
贴标签位
Lead free
标
PCS
签
示
图
注明：SMD5050 系列包装标准 1000PCS/包，特别要求除外。
文件编号：SPC-TOP- A/20701
PAGE: 8th
深圳市丽创光电有限公司
Shenzhen Lictron Co.,LTD
Smart SMD LED 属于湿敏元件，将 LED 包装在铝箔袋中是为了避免 LED 在运输和储存时吸收湿气，在包装袋中 放 有干燥剂，以吸收湿气，如果 LED 吸收了湿气，在 LED 过回流焊时，湿气就会膨胀，使胶体与支架脱离，或损 害键 合金丝，造成产品失效，由于这个原因，真空防湿包装是为了使包装袋内避免有湿气，此款产品防潮等级为 LEVEL5a。 表一：IPC/JEDEC J-STD-020 规定的材料防潮等级（MSL)定义
台湾晶元5050lmw5050w-3规格书18-20lm
承认书Samples approval sheet客户名称（Customer name）：宋生：组件名称（Production name）：贴片发光二极管型号（Model）： LMW5050W-3 编号（Part number）：日期（Date）： 2011-5-14型号Model：LMW5050W-3页码Page: 1/6一、外形图Outline dimensions：单位Unit公差Tolerance胶体颜色Lens color发光颜色Emission colormm±White白色white※备注：承认书之编号和型号可用于查询，客户如有需要，请提供相应的编号和型号。
Remark：P/N & Model in samples approval sheet can be used to inquire，please provide corresponding P/N& model if customer need .型号Model：LMW5050W-3页码Page：2/6型号Model：LMW5050W-3页码Page： 3/6四、典型光电特性曲线图Typical photoelectricity characteristic curve chart型号Model：LMW5050W-3页码Page： 4/6型号Model：LMW5050W-3页码Page： 6/6型号Model：LMW5050W-3页码Page： 5/6六、注意事项 Note（一）引脚成形方法Led bracket forming method（1）必需离胶体2毫米才能折弯支架。
The pin of led can be bent where is at least 2mm out of led colloid.（2）支架成形必须用夹具或由专业人员来完成。
Must use fixture to deform the led bracket.（3）支架成形必须在焊接前完成。
5050参数
LED SMD5050产品简介与规格参数☆产品特性1、外形尺寸：5.0×5.0×1.6mmOutline package：5.0×5.0×1.6mm2、胶体颜色：无色透明Lens appearance: Water or Yellow Clear3、发光效率和显色性高High luminous efficiency and high color display4、光谱窄，单色性好Narrow spectrum and good single color5、功耗低，精密恒流Low power consumption ,precision constant current6、硅胶封装，低衰减Silicone package ,low brightness attenuation☆产品应用1、室内室外显示屏和广告屏2、信号和指示照明Indoor or outdoor displays and billboard Signal and symbol Illumination 3、背光源4、汽车内部和尾灯照明Back lighting Interior automotive and tail lighting 5、LED日光灯和球泡灯6、LED灯条LED daylight tube and LED globe bulb LED strip☆外型尺寸图Package Outline Dimensions☆焊盘设计PAD Lay Out PCBLED SMD5050 0.2W正白最大绝对额定值Absolute maximum ratings at Ta=25度参数 Parameter 符号Symbol 值Value 单位Unit 功率耗损Power dissipation Pd 200 mW正向电流Forward current If 70 mA反向电压Reverse voltage Vr 5 V 工作温度范围Operating temperature range Topr ﹣40－﹢80 ℃贮存温度范围Storage temperature range Tstg ﹣40－﹢85 ℃最大脉冲电流Peak pulsing current Ifp 100 mA 抗静电能力Electrostatic Discharge ESD 4000 VLED SMD5050 0.2W正白光电特性Electrical optical characteristics at Ta=25度参数Parameter符号Symbol值Value单位Unit测试条件Test Conditions Min Typ Max正向电压Forward voltage VF 3.0 / 3.6 V IF=60 mA 发光强度Luminous intensity IV 3000 4500 Mcd IF=60 mA 角度Viewing angles2θ1/2 120 Dge IF=60 mA 色温Color temperature TC 5500 6500 K IF=60 mA 光通量Luminous flux/ 10 12 Lm IF=60 mA 反向电流Reverse current IR 10 μA VR=5VLED SMD5050 0.2W其他产品光电参数发光颜色Emitting Color 产品型号Model正向电压ForwardVoltage(v)正向电流ForwardCurrent(mA)色温或波段CCT(k) orWD(nm)发光强度LuminousIntensity(Mcd)角度Beanangel(°)蓝色(Blue)SY-5050-BE02 3.0—3.660 460-465600-1800 120 绿色(Green)SY-5050-GN02 3.0—3.660 520-5251800-3000 120 红色(Red )SY-5050-RD02 1.8—2.4 60 620-625800-1500 120 黄色(Yellow)SY-5050-YW02 1.8—2.4 60 585-590600-1500 120RGB SY-5050-RGB021.8—2.4 60 620-625(R)300-500 120 3.0—3.6 60 520-525(G)600-1200 120 3.0—3.6 60 460-465(B)250-600 120温馨提示：所有参数均为实验得出的统计参数，因测试设备、具体使用芯片不同，具体参数以单个产品实验数据为准。
布里德拉克斯SMD 5050系列强力LED数据手册说明书
Product Data Sheet DS69The Bridgelux SMD 5050 Gen2 high power LED is hot-color targeted, which ensures that the LEDs fall within their specified color bin at the typical application conditions of 85°C. With its broad lumen coverage and wide range of CCT options, the SMD 5050 provides unparalleled design-in flexibility for indoor and outdoor lighting applications. The SMD 5050 is ideal as a drop-in replacement for emitters with an industry standard 5.0mm x 5.0mm footprint.Features• Industry-standard 5050 footprint• 3 bin color control enables tight color control• Hot-color targeting ensures that color is within the ANSI bin at the typical application conditions of 85°C • Enables 3- and 5-step MacAdam ellipse custom binning kits• RoHS compliant and lead free• Multiple CCT configurations for a wide range of lighting applicationsBenefits• Lower operating and manufacturing cost• Ease of design and rapid go-to-market• Uniform consistent white light• Reliable and constant white point• Environmentally friendly, complies with standards • Design flexibilityContentsProduct Feature MapProduct NomenclatureThe part number designation for Bridgelux SMD 5050 is explained as follows:Product Test ConditionsBridgelux SMD 5050 Gen2 LEDs are tested and binned with a 10ms pulse of 125mA at T j (junction temperature)=T sp (solder point temperature) =25°C. Forward voltage and luminous flux are binned at a T j =T sp =25°C, while color is hot targeted at a T sp of 85°C.Bridgelux SMD LED products come in industry standard package sizes and follow ANSI binning standards. These LEDs are optimized for cost and performance, helping to ensure highly competitive system lumen per dollar performance while addressing the stringent efficacy and reliability standards required for modern lighting applications.1 2 3 4 5 6 7 8 9 10 11 12 1314 15 16Product FamilyColor Bin OptionsFlux BinsMinimum CRIC = 70 CRI E = 80 CRI G = 90 CRIForward Voltage Bins Nominal CCT27 = 2,700K 30 = 3,000K 35 = 3,500K 40 = 4,000K 45 = 4,500K 50 = 5,000K 57 = 5,700K 65 = 6,500KBXEP – 30 E – 1 C 5 – 36 B – 00 – 00 – oProduct VersionPower 5 = 4.4W Die count in parallelTypical Forward VoltageDie count in series Yellow phosphor Light Emitting Surface (LES)Cathode MarkProduct Selection GuideThe following product configurations are available:Table 1: S election Guide, Pulsed Measurement Data at 125mA (T j =T sp =25°C)Notes for Table 1:1. The last 7 characters (including hyphens ‘-’) refer to flux bins, forward voltage bins, and color bin options, respectively. “00-00-0” denotes the full distribution of flux, forward voltage, and 7 SDCM color. Example: B XEP-30E-1C5-36B-00-00-0 refers to the full distribution of flux, forward voltage, and color within a 3000K 7-step ANSI standard chromaticity region with a minimum of 80CRI, 1x12 die configuration, 4.4w power, 35.5V typical forward voltage.2. Product CCT is hot targeted at T sp = 85°C. Nominal CCT as defined by ANSI C78.377-2011.3. Listed CRIs are minimum values and include test tolerance.4. Products tested under pulsed condition (10ms pulse width) at nominal drive current where T j =T sp =25°C.5. Bridgelux maintains a ±7.5% tolerance on luminous flux measurements, ±0.1V tolerance on forward voltage measurements, and ±2 tolerance on CRI measurements for the SMD 5050 Gen2.6. Refer to Table 6 and Table 7 for Bridgelux SMD 5050 Gen2 Luminous Flux Binning and Forward Voltage Binning information.Product Selection GuideThe following product configurations are available:Notes for Table 2:1. The last 7 characters (including hyphens ‘-’) refer to flux bins, forward voltage bins, and color bin options, respectively. “00-00-0” denotes the full distribution of flux, forward voltage, and 7 SDCM color. Example: B XEP-30E-1C5-36B-00-00-0 refers to the full distribution of flux, forward voltage, and color within a 3000K 7-step ANSI standard chromaticity region with a minimum of 80CRI, 1x12 die configuration, 4.4w power, 35.5V typical forward voltage.2. Product CCT is hot targeted at T sp = 85°C. Nominal CCT as defined by ANSI C78.377-2011.3. Listed CRIs are minimum values and include test tolerance.4. Bridgelux maintains a ±7.5% tolerance on luminous flux measurements, ±0.1V tolerance on forward voltage measurements, and ±2 tolerance on CRI measurements for the SMD 5050 Gen2.5. Refer to Table 6 and Table 7 for Bridgelux SMD 5050 Gen2 Luminous Flux Binning and Forward Voltage Binning information.6. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.7. Typical performance is estimated based on operation under DC (direct current) with LED emitter mounted onto a heat sink with thermal interfacematerial and the solder point temperature maintained at 85°C. Based on Bridgelux test setup, values may vary depending on the thermal design of the luminaire and/or the exposed environment to which the product is subjected.Table 2: Selection Guide, Stabilized DC Performan ce (T sp = 85°C)6,7Table 3:Performance at Commonly Used Drive CurrentsSMD 5050 LEDs are tested to the specifications shown using the nominal drive currents in Table 1. SMD 5050 may also be driven at other drive currents dependent on specific application design requirements. The performance at any drive current can be derived from the current vs. voltage characteristics shown in Figure 2 and the relative luminous flux vs. current characteristics shown in Figure 3. The performance at commonly used drive currents is summarized in Table 3.Notes for Table 3:1. Alternate drive currents in Table 3 are provided for reference only and are not a guarantee of performance.2. Bridgelux maintains a ± 7.5% tolerance on flux measurements.3. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.Table 3:Performance at Commonly Used Drive CurrentsSMD 5050 LEDs are tested to the specifications shown using the nominal drive currents in Table 1. SMD 5050 may also be driven at other drive currents dependent on specific application design requirements. The performance at any drive current can be derived from the current vs. voltage characteristics shown in Figure 2 and the relative luminous flux vs. current characteristics shown in Figure 3. The performance at commonly used drive currents is summarized in Table 3.Notes for Table 3:1. Alternate drive currents in Table 3 are provided for reference only and are not a guarantee of performance.2. Bridgelux maintains a ± 7.5% tolerance on flux measurements.3. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.Table 3:Performance at Commonly Used Drive Currents(Continued)Notes for Table 3:1. Alternate drive currents in Table 3 are provided for reference only and are not a guarantee of performance.2. Bridgelux maintains a ± 7.5% tolerance on flux measurements.3. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.Table 3:Performance at Commonly Used Drive Currents (Continued)Notes for Table 3:1. Alternate drive currents in Table 3 are provided for reference only and are not a guarantee of performance.2. Bridgelux maintains a ± 7.5% tolerance on flux measurements.3. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.Electrical CharacteristicsNotes for Table 4:1. The last 7 characters (including hyphens ‘-’) refer to flux bins, forward voltage bins, and color bin options, respectively. “00-00-0” denotes the full distribution of flux, forward voltage, and 7 SDCM color. Example: B XEP-30E-1C5-36B-00-00-0 refers to the full distribution of flux, forward voltage, and color within a 3000K 7-step ANSI standard chromaticity region with a minimum of 80CRI, 1x12 die configuration, 4.4w power, 35.5V typical forward voltage.2. Bridgelux maintains a tolerance of ± 0.1V on forward voltage measurements. Voltage minimum and maximum values at the nominal drive current are guaranteed by 100% test.3. Products tested under pulsed condition (10ms pulse width) at nominal drive current where T sp = 25°C.4. Thermal resistance value was calculated using total electrical input power; optical power was not subtracted from input power.Table 4: Electrical CharacteristicsAbsolute Maximum RatingsTable 5: Maximum RatingsNotes for Table 5:1. The condition of the maximum drive current is limited, Figure 7 can be reference.2. Bridgelux recommends a maximum duty cycle of 10% and pulse width of 10 ms when operating LED SMD at maximum peak pulsed current specified.Maximum peak pulsed current indicate values where LED SMD can be driven without catastrophic failures.3. The maximum drive current for LM80 test result is based on 128% nominal drive current listed.Table 6: Luminous Flux Bin Definitions at 125mA, T sp=25°CTable 6 lists the standard photometric luminous flux bins for Bridgelux SMD 5050 LEDs. Although several bins are listed, product availability in a particular bin varies by production run and by product performance. Not all bins are available in all CCTs.Table 7: Forward Voltage Bin Definition at 125mA, T sp=25°CNote for Table 7:1. Bridgelux maintains a tolerance of ± 0.1V on forward voltage measurements.Note for Table 6:1. Bridgelux maintains a tolerance of ± 7.5% on luminous flux measurements.Table 8: 3- and 5-step MacAdam Ellipse Color Bin DefinitionsNotes for Table 8:1. Color binning at T sp =85°C2.Bridgelux maintains a tolerance of ± 0.007 on x and y color coordinates in the CIE 1931 color space.Figure 1: C.I.E. 1931 Chromaticity Diagram (3 Color Bin Structure, hot-color targeted at T=85°C)spNote for Figure 3:1. Bridgelux does not recommend driving high power LEDs at low currents. Doing so may produce unpredictable results. Pulse width modulation (PWM) is recommended for dimming effects.Figure 2: Drive Current vs. Voltage (T sp =25°C)Figure 3: Typical Relative Luminous Flux vs. Drive Current (T sp =25°C)Figure 4: Typical Relative DC Flux vs. Solder Point TemperatureFigure 5: Typical DC ccx Shift vs. Solder Point TemperatureNotes for Figures 4 & 5:1. Characteristics shown for warm white based on 2700K and 80 CRI.2. Characteristics shown for neutral white based on 4000K and 80 CRI.3. Characteristics shown for cool white based on 5700K and 80 CRI.4. For other color SKUs, the shift in color will vary. Please contact your Bridgelux Sales Representative for more information.Figure 6: Typical DC ccy Shift vs. Solder Point TemperatureNotes for Figure 6:1. Characteristics shown for warm white based on 2700K and 80 CRI.2. Characteristics shown for neutral white based on 4000K and 80 CRI.3. Characteristics shown for cool white based on 5700K and 80 CRI.4. For other color SKUs, the shift in color will vary. Please contact your Bridgelux Sales Representative for more information. Figure 7: Drive Current Derating CurveTypical Radiation PatternFigure 8: Typical Spatial Radiation Pattern at 125mA, T sp =25°CFigure 9: Typical Polar Radiation Pattern at 125mA, T sp =25°CNotes for Figure 8:1. Typical viewing angle is 116⁰.2.The viewing angle is defined as the off axis angle from the centerline where luminous intensity (Iv) is ½ of the peak value.Typical Color Spectrum Figure 10: Typical Color SpectrumNotes for Figure 10:= 25°C1. Color spectra measured at nominal current for Tsp2. Color spectra shown for warm white is 2700K and 80 CRI.3. Color spectra shown for neutral white is 4000K and 80 CRI.4. Color spectra shown for cool white is 5700K and 80 CRI.Mechanical DimensionsFigure 11: Drawing for SMD 5050Notes for Figure 11:1. Drawings are not to scale.2. Drawing dimensions are in millimeters.3. Unless otherwise specified, tolerances are ± 0.10mm.Recommended PCB Soldering Pad PatternReliabilityTable 9: Reliability Test Items and ConditionsNotes for Table 9:1. Measurements are performed after allowing the LEDs to return to room temperature2. T sld : reflow soldering temperature; T a: ambient temperaturePassing CriteriaFigure 12 :Reflow ProfileReflowing CharacteristicsFigure 13 : Pick and PlaceNote for Figure 13:1. When using a pick and place machine, choose a nozzle that has a larger diameter than the LED’s emitting surface. Using a Pick-and-Place nozzle witha smaller diameter than the size of the LEDs emitting surface will cause damage and may also cause the LED to not illuminate.Is greater than LEDsemitting surfaceFigure 14: Emitter Reel DrawingsNote for Figure 14:1. Drawings are not to scale. Drawing dimensions are in millimeters. Figure 15: Emitter Tape DrawingsNote for Figure 15:1. Drawings are not to scale. Drawing dimensions are in millimeters.Figure 16: Emitter Reel Packaging DrawingsNote for Figure 16:1. Drawings are not to scale.Design ResourcesDisclaimersPrecautionsPlease contact your Bridgelux sales representative for assistance.MINOR PRODUCT CHANGE POLICYThe rigorous qualification testing on products offered by Bridgelux provides performance assurance. Slight cosmetic changes that do not affect form, fit, or function may occur as Bridgelux continues product optimization.CAUTION: CHEMICAL EXPOSURE HAZARDExposure to some chemicals commonly used in luminaire manufacturing and assembly can cause damage to the LED emitter. Please consult Bridgelux Application Note AN51 for additional information.CAUTION: EYE SAFETYThis SMD package emits visible light, that, under certain circumstances, could be harmful to the eye. Proper safe -guards must be used.CAUTION: RISK OF BURNDo not touch the SMD LED emitter during operation. Allow the emitter to cool for a sufficient period of time before handling. The SMD LED emitter may reachelevated temperatures such that could burn skin when touched.CAUTIONCONTACT WITH LIGHT EMITTING SURFACE (LES) Avoid any contact with the LES. Do not touch the LES of the emitter or apply stress to the LES (yellow phosphor resin area). Contact may cause damage to the emitterOptics and reflectors must not be mounted in contact with the LES (yellow phosphor resin area).STANDARD TEST CONDITIONSUnless otherwise stated, LED emitter testing is performed at the nominal drive current.About Bridgelux: We Build Light That Transforms© 2018 Bridgelux, Inc. All rights reserved 2018. Product specifications are subject to change without notice. Bridgelux and the Bridgelux stylized logo design are registered trademarks of Bridgelux, Inc. All other trademarks are the property of their respective owners.46430 Fremont Boulevard Fremont, CA 94538Tel (925) At Bridgelux, we help companies, industries and people experience the power and possibility of light. Since 2002, we’ve designed LED solutions that are high performing, energy efficient, cost effective and easy to integrate. Our focus is on light’s impact on human behavior, delivering products that create better environments, experiences and returns—both experiential and financial. And our patented technology drives new platforms for commercial and industrial luminaires.For more information about the company, please visit /Bridgelux /Bridgelux/user/Bridgelux WeChat ID: BridgeluxInChina。
LA-5050RGB-A LED说明书
LA-5050RGB-A●目录：（Content）◆封面:(Cover)━‥━‥━‥━‥━‥━‥━‥━‥━‥‥━‥━‥PAGE:1OF12◆产品简介(Product introduction)━‥━‥━‥━‥━‥━‥‥━‥━‥PAGE:2OF12◆外形尺寸图及应用领域(Outline Dimensions)━‥━‥━‥━‥━‥━PAGE:3OF12◆产品编码解说及光电参数：Electrical-Optical Characteristics━‥━‥PAGE:4OF12◆色区分BIN及色温坐标：（Intensity Bin Limit）━‥━‥‥━‥━‥━PAGE:5OF12◆光电特性曲线图：（Optical Characteristics）━‥━‥━‥━‥━‥━‥PAGE:7OF12◆信赖度测试项目及标准：（Test items and results of reliability）‥‥‥PAGE:8OF12◆包装规范：（Packing）━‥━‥━━‥━‥━━‥━‥━‥━‥━‥━‥PAGE:9OF12◆产品使用说明及注意事项:(Usage and Handling Instructions)‥‥‥PAGE:10-12OF12●特性：（Features）◆ 5.4长*5.0宽*1.6高：（5.4mm*5.0mm*1.6mm SMT LED Thickness.）◆角度：120度：（View Anglc:120°）◆包装：1000/一盒：（Package：1000PCS/Packet）◆发光颜色：RGB（Emitted Color:RGB）◆混色型：（Mono-color type）◆工作温度：-40～80度：（Operating Temperature:-40～+80℃）◆焊接温度：260度10秒：（S oldering Temperature：260for10sec℃）◆超大功率：（Supper High Power Consumption）◆可做不同的种类：（Various Colors And Types Available.）◆胶水：硅胶：（Resin(Mold):Silicone）◆反向电压5V：（Reverse Voltage:5V）◆储存温度-40～+100度：（Storage Temperature:-40～+100℃）◆脉冲电流60mA注：脉冲宽度0.1mS占空比1/10Pulsed Forward Current60mA(Duty1/10,Pulse Width0.1mS.）LA-5050RGB-ALA-5050RGB-ALA-5050RGB-A●分BIN参数：（Color Coordinate Comparison）·色坐标范围LA-5050RGB-A●典型光学特性曲线：（Typical optical characteristics curves）环境温度与正向电流特性曲线正向电流与相对光强特性曲线Ambient Temperature vs.Forward Current Forward Current VS.Relative Intensity正向电压与正向电流特性曲线环境温度与相对光强特性曲线Forward Voltage VS.Forward Current Ambient Temperature VS.Relative Intensity相对光谱分布特性曲线辐射图特性曲线Relative spectral emission Radiation diagramLA-5050RGB-ALA-5050RGB-A●包装规格✧标签：（Label）卷轴尺寸：（Reel Dimensions）✧载带规格（单位：mm):（Tape Specifications(Units:mm）✧防潮带包装：（Moisture Resistant Packaging）注：标注公差为±0.1mm，单位：mm：（Note:The tolerances unless mentioned is±0.1mm,Unit:mm）LA-5050RGB-A●回流焊接曲线图（IR reflow soldering Profile）✧有铅焊接（Lead solder）✧无铅焊接（Lead Free solder）注意：（NOTES：）1.我们建议的回流焊温度为240℃±5℃，最高的焊接温度要控制在260℃以内。
5050RGB规格书(中文)
标示区有无由蓝色变为粉红色.如漏气或变色现象,请联系厂家或退回厂家高温除湿处理,(高温除湿 环境：120 度，6H)切勿自行处理 2-2. 打开包装前， LEDs 需储存在温度低于 30℃，湿度低于 70%RH 。 2-3. 打开包装后，在温度低于 30℃ ，湿度低于 60%RH 的情况下，且开封到焊接完成控制在 4H。 2-4. 如果吸湿材料 (硅凝胶)已经消退或是 LEDs 已经超过了储存时间, 则需要基于以下条件进行烘烤 处理： 60±5℃ / 24 小时。 3. 回流焊注意事项 3-1. 无铅锡膏的温度曲线
█ 电性与光学特性(Ta=25℃)
参数 正向电压 反向电流 发光角度 波长
光通量
符号
条件
最小 平均 最大 单位
R IF=20mA
2.0
--
2.3
VF G IF=20mA
2.9
--
3.2
V
B IF=20mA
2.9
--
3.2
IR
VR=5V
--
--
5
μA
2θ1/2
IF=3*20mA
--
120
--
deg
R IF=20mA
3-2. 回流焊不能超过两次。 3-3. 焊接期间, 加热时不要在 LEDs 上添加任何压力。 3-4. 焊接后, 正常回温至 40℃以下后才可过电流。 4. 防护措施
用适当的工具从材料侧面夹取，因产品使用硅胶封装避免在应用过程中压伤胶体，损伤内部结构造
成不良。LED 为半导体敏感器件，静电放电（ESD）或脉冲电流（EOS）可能会损害 LED。 作业机台 有效接地、作业中作好静电防护，可有效提升产品品质。贴片 LED 灯珠在生产过程中及灯具使用环境 需避免与硫.卤素.酸.醇.碱.酮肟类挥发性化合物,强氧化物.增塑剂(又名塑化剂,领苯二甲酸二辛酯 DOP 或邻苯二甲酸二丁酯 DBP,PVC 物料即含有大量增塑剂)等腐蚀性物质接触
5050RGB声控灯条规格书
使用本产品之前，敬请仔细阅读本手册，确保完全理解本规格书以避免不必要的损坏和额外的费用。
产品简介LED RGB声控灯条采用先进的PWM控制技术，能够实现多钟RGB颜色变化（详细模式见下文）；采用RF无线射频遥控进行模式选择调节，实现静态、跳变、渐变和音频感应等灯光变化效果，同时客户可根据实际需求对静态颜色进行亮度调节，对动态变化进行速度调节；该款产品是基于音频分析技术和更人性化遥控器设计基础上进行升级的第二代音乐控制器,达到完美的音频控制效果和用户体验；并可以与本公司的RGB信号放大器进行功率扩展，实现更多LED灯的同步化，理论上可以连接无数个RGB放大器。
技术参数工作温度-20-60℃供电电压12~24V静态功耗<1W连接方式共阳灰度级256级（可连发）速度档100级（可连发）净重185g毛重215g外型尺寸L130ΧW64ΧH24 mm包装尺寸L137ΧW80ΧH54 mm输出3回路输出电流≤4A(每回路)遥控方式RF发射接收频率433.92Mhz遥控距离20m模式14种控制器输出功率12V:≤144W产品特点1、产品供电电压12V电压；2、输出为三回路，每路允许最大电流为4A，能带12V30灯/米的灯带20米，12V60灯/米的灯带10米；3、采用RF无线遥控方式，具有遥控距离远，无方向性，可穿透一定厚度阻碍物等特点，环境的不同，最大距离可以达到20米；常规产品的无线遥控器是可通用的，如需要一对一控制，需要对其编码；4、具有断电记忆存储功能，每次上电都会保留上次掉电时的变化模式；5、14种模式，包括8种静态颜色、3种动态变化和3种音乐模式，其中3种音乐模式分别对应F.T.:DJ(快节奏变化)、M.T.:动感(通用型的节奏变化)、C.T.:柔情(慢节奏变化)；音频模式时可通过黑色旋钮调节灵敏度；6、音频控制可以通过麦克风和音频线输入信号两种方法实现;7、为了实现更多灯具的同步，可与本公司的RGB信号放大器进行功率扩展。
规格书(一米10段60灯)
SM16703 IC（5050）灯条规格书一米10段60灯LED全彩灯条又名LED幻彩灯条，LED数码灯条，像素灯条，英文名为：LED pixel strips，产品为柔性FPC(软灯条板)/PCB(硬灯条板)为基板焊接LED，以及外围电路形成，可以实现追逐，流水，幻彩，显示效果等，主要用于KTV，酒店，家庭等等地方的装饰.SM16703全彩灯条采用一个IC六个灯,俗称”一拖六”,IC为SM16703,灯珠是5050RGB灯珠.工作电压为24V直流电压,配备24V全彩控制器可实现渐变/跳变，单/多跑马变，流水/追逐变，流星/快闪,单色变/混和变等等各种效果模式！灯带带有智能IC芯，可通过全彩控制器或带有编程的，达到任何想要的效.*产品规格*产品名称: 10段60灯灯珠型号: 5050RGB内置IC灯珠型号: SM16703工作电压: 24V功率：±18W/米灰度等级：256数据传输速率：800K/S工作温度：-40°C---80°C工作寿命：30Kh灯珠数量: 60灯/米IC数量: 10个IC/米（集成到了灯珠外部）10个像素点/米发光颜色：全彩/通过控制器控制能实现任意颜色任意效果（可定制其他单色跑马）点间距：板宽：12MM板底颜色：白板 / 黑板防水等级与重量：裸板-不防水 -滴胶防水-IP65 -套管防水-IP66 -灌胶防水-IP68 -包装：5米/盘卷盘固定防静电袋包装裸板-不防水：两端出三并对插接头外加双色电源线；背面贴3M强力双面胶；5米/盘，卷盘固定静电袋包装出货滴胶防水-IP65：表面覆盖一层透明防护硅胶；两端出三并对插接头外加双色电源线；背面贴3M强力双面胶；5米/盘，卷盘固定静电袋包装出货套管防水-IP65：将灯条置入360度全方位保护的硅胶套管内部；两端堵头堵死出三并对插接头外加双色电源线；5米/盘，卷盘固定静电袋包装出货灌胶防水-IP68：全方位保护的硅胶套管内部再注满透明硅胶；两端堵头堵死出三并对插接头外加双色电源线（也可出特制的防水对插接头）；5米/盘，卷盘固定静电袋包装出货*产品优点*1、比传统的单色灯条更漂亮、色彩更绚丽。
5050 0.5W规格书
Color bin limit(If=150mA)—◎white
色区范围(IF=150mA) —白光
Bin
X
Y
Bin
X
Y
Bin
0.283 0.284
0.3035 0.332
0.295 0.297
0.315 0.3435
A0
A7
B4
0.298 0.288
0.316 0.332
0.287 0.276
0.306 0.322
Y 0.357 0.3697 0.3568 0.345 0.369 0.3827 0.3697 0.357 0.3812 0.3956 0.3827 0.369 0.321 0.342 0.332 0.3135 0.342 0.355 0.3435 0.332
White CIE Chromaticity Diagram
Our 5050 products, use silica gel packages, effectively improve the heat dissipation performance. Reliability is better than companies in general, it is a complete white combination with high brightness, low-light decay characteristics.
0.316 0.332
0.329 0.33
0.317 A6
0.308
0.319 0.311
0.329 0.345 B3
0.3455 0.3568
0.306 0.322
0.3442 0.3421
X 0.329 0.3466 0.3455 0.329 0.329 0.3478 0.3466 0.329 0.329 0.3489 0.3478 0.329 0.287 0.301 0.3035 0.2895 0.301 0.314 0.315 0.3035
5050系列高压灯带规格书1doc
60
LUX-FLT50SW060C-230-020 White 765 lm
60
LUX-FLT50SW060C-230-050 White 765 lm
60
LUX-FLT50WW060C-230-005
Warm white
665 lm
60
LUX-FLT50WW060C-230-020
Warm white
-5-
-2-
深圳纳科士光电科技有限公司
Shenzhen Luxes Optoelectronics CO,.Ltd
Lux-FLT50XX060C-230-XXX
产品光电参数表：
产品型号
颜色
光通量 LED 数
/M
量/M
LUX-FLT50SW060C-230-005 White 765 lm
3．不要将灯带作连续性的扭曲，多次扭曲易造成内部电源线路疲劳损伤，扭 曲角度不小于 45 度，不要在直径 60mm 以下的弧度弯曲。软灯带在户外、 户内使用应做好安全防范措施，以免减少火灾，电击和人身伤害。
4. 在安装时用螺丝将轨道固定在要装饰的物体表面上，将灯嵌入轨道夹内， 注意灯体的发光面部分要朝上。软灯带在使用过程中，请勿用任何物体包 住，遮盖软灯带表面。
使用注意事项
1．每条灯带均接有整流桥堆和插头，只需将插头插入电源插座内即可方便使 用。使用前请明确产品功率，确保供电线路不超负荷，电路有电路保护 器，如电源插座带有保险丝或接了漏电开关。使用时请参照产品技术及光 电参数内容，确保在电压参数±5%范围内工作。
2．如需自定义长度，应在单元组焊接位置剪切，不可小于最小单元长度或在 单元组内剪切。剪切后须注意，切口应用防水绝缘胶封好，以免烧坏产品 或出现安全事故（因此造成的损失，产品供应商不负责）。我司不建议客 人自行裁剪长度，如需求非标准长度产品，请与我司市场人员联系。
5050灯珠规格书
0.4386
4000K
Rank
CIE-X
0.3760
40C02 0.3859 (3900-4100K) 0.3920
0.3822
5000K
Rank
CIE-X
0.3444
50C02 0.3469 (4700-5000K) 0.3558
0.3539
6500K
Rank
CIE-X
0.3104
CIE-Y 0.424 0.4116 0.4204 0.4329
条件 =60mA
=60mA =60mA =60mA
最小
18 20 22
2.9 3.0 3.1 3.2 3.3 118
62
最大
20 22 24
3.0 3.1 3.2 3.3 3.4 123
85
单位 lm V deg -
4
4.: 03/01/2013: 03/01/2013 Rev: 01
5050 灯珠规格书
ZT5050W: 03/01/2013 Rev: 01
目录
1.产品描述 2.最大额定值 3.光电参数 4.典型光电特性曲线 5.分光标准 6.可靠性测试 7.产品规格尺寸 8.料盘结构和包装 9.回流焊 10.使用注要事项
240℃ 20-40 秒 最大 6℃/每秒 最大 8 分钟
10.使用注意事项 储存 (1) 打开包装前 在温度不超过 40℃及湿度不超过 90%RH 条件下，LED 可以保存一年，在储存的时候， 建议采用带干燥剂的防潮袋的包装方式。 (2)打开包装后 LED 需要储存在<=40℃＆<=60%RH 相对湿度的条件下，我们强烈建议您从打开包装到 完成贴片整个过程在一个星期内完成。 如果有未使用完的剩余 LED，我们建议重新使用出厂时的防潮剂，并且需要重新密封。 如果干燥剂过期了，请将 LED 放在 60℃烤箱烘烤 12 小时。 LED 电极和引线框架是由表面镀了银的铜合金构成，镀银层会受到来自周围环境的破 坏，请把 LED 远离那种会腐蚀 LED 电极镀银层的环境，LED 电极被腐蚀后，会降低它的 焊接能力和光电参数。 请避免 LED 使用在温度快速变化的环境中，尤其是会发生冷凝的高湿环境中。
灯带的规格
灯带的规格LED灯带规格参数颜色 LED灯带规格(mm) LED数量波长/色温(nm/k) 亮度(mcd) 电压(V) 电流（A）每组功率（W）每米功率(W) 连接最长长度(米)红色 500x8 30 620~625 460~600 12 0.2 0.24 4.8 15黄色 500x8 30 589~592 350~460 12 0.2 0.24 4.8 15蓝色 500x8 30 465~470 350~460 12 0.2 0.24 4.8 15绿色 500x8 30 520~525 1000~1300 12 0.2 0.24 4.8 15正白 500x8 30 6500~8000 1400~1600 12 0.2 0.24 4.8 15暖白 500x8 30 3500~4500 1300~1700 12 0.2 0.24 4.8 15二、5050 LED灯带规格参数5050 LED灯带规格参数颜色灯带规格（mm）波长/色温(nm/k) 亮度（mcd）电压(v) 电流（A）每组功率(W) 每米功率(W) LED数量最长连接长度(米)红色 500x10 621~624 1000~1200 12 0.3 0.72 7.2 15 10蓝色 500x10 461~464 1000~1200 12 0.3 0.72 7.2 15 10绿色 500x10 515~518 2900~3770 12 0.3 0.72 7.2 15 10黄色 500x10 590~593 800~1000 12 0.3 0.72 7.2 15 10正白 500x10 6500~8000 4600~5000 12 0.3 0.72 7.2 15 10暖白 500x10 3500~4500 4600~5000 12 0.3 0.72 7.2 15 10R 500x10 621~624 210~275 12 0.2 0.24 2.4 15 10G 500x10 512~515 1000~1200 12 0.2 0.24 2.4 15 10B 500x10 464~467 275~355 12 0.2 0.24 2.4 15 10三、LED跑马灯带规格参数0603系列LED跑马灯带规格参数颜色灯带规格(mm) LED数量波长/色温(nm/k) 亮度(mcd) 电压(v) 电流(A) 每组功率(w) 每米功率（w）最长连接长度(米) 红色 500x10 36 620~625 300 12 0.24 0.24 5.76 12蓝色 500x10 36 465~470 150 12 0.24 0.24 5.76 12绿色 500x10 36 520~525 500 12 0.24 0.24 5.76 12黄色 500x10 36 589~592 220 12 0.24 0.24 5.76 12正白 500x10 36 6500~7500 700 12 0.24 0.24 5.76 12暖白 500x10 36 3500~4500 500 12 0.24 0.24 5.76 12。
LED 5050硬灯条规格书
确认后请回传,谢谢!Please confirm and fax to us ,thank you!XL-5050 LED 硬灯条产品效果展示：LED 硬灯条 5050灯珠效果 LED 硬灯条 5050灯珠效果一、 特点：1、采用高亮度SMD5050 LED 灯珠 ， 铝合金外壳 ， 每三个LED 为一段。
2、每条的标准长度为1M ，每条灯珠数量分别有 30PCS/M LED 灯珠 ，60PCS/M LED 灯珠 ，72PCS/M LED 灯珠3、发光颜色：红/绿/蓝/黄/白/暖白和长彩等多种颜色可供选择4、工作电压：DC12V/DC24V 两种5、防水型SMD 灯条，表面采用灌胶二、 用途：1、SMD 高亮度硬灯条适用于酒店，超薄灯箱，KTV 娱乐场所等室内装饰。
2、用于广告招牌等精品装饰领域。
3、度假装饰照明灯，显示及展览。
4、商场专柜，珠宝，首饰台及名贵钟表柜台。
三、产品规格：四、参数灯珠类型号： SMD 5050 LED 可选颜色： 红/绿/蓝/黄/白/暖白/RGB发光角度: 120度 灯珠数量: 30PCS / M 60PCS / M 72PCS / M 外形尺寸: 1000*10*2mm 按整体封存装: 裸板 V 型槽 U 型槽硬灯条套V 型槽图示硬灯条裸板图示U 型槽图示五、 注意事项：六、产品应用应用家居装饰应用KTV 装饰珠宝柜装饰●使用说明use manual:1.请先仔细阅读产品规格书,确认其使用环境是否符合规格书上的条件上,方可放心使用. Please read the specificationfirst to make sure the using condition is fit2.将产品接入电源时,请先确保开关处于闭合状态..Please shut off the switch before connect the product, then turn on3.本产品保质期为一年This product warranty for one year4.。
5050RGBLED灯珠全彩规格书88
DONGGUAN TONGJIA OPTOELECTRONICS TECHNOLOGY CO., LTD
承 認 書 Specification For Approval
Customer: (客戶) Description:(產品描述)
Typ 3.2 2.1 --625 521 468 800 2000 500 120
Max ----2
Unit V
Forward Voltage
VF ( IF =20mA)
R
Reverse Current Dominant Wavelength
IR Λd(IF =20mA)
VR =5V R G B R
Customer Service Hotline：400-6பைடு நூலகம்6-8616
TEL：0769-8200 5999 0769-8200 2226 FAX：0769-8200 2777 E-MIAL∶tongjiacn@
5
WEB：
TAIWAN TONGJIA OPTOELECTRONICS TECHNOLOGY CO., LTD
1
WEB：
TAIWAN TONGJIA OPTOELECTRONICS TECHNOLOGY CO., LTD
DONGGUAN TONGJIA OPTOELECTRONICS TECHNOLOGY CO., LTD
■Absolute Maximum Ratings (Ta = 25℃)
Approved By: (客戶承認)
Prepared By:(我司承認)
Approval Check Design Sales
5050RGBW中文规格书
5050RGBW中文规格书型号：YT5050RGBWOS4-4560描述:5050RBGW贴片发光二极管是5050RGB行业内标准的封装产品的升级版，此类产品为高可靠性及应用范围非常广泛，此高可靠性的产品非常适用于半户外及户外全彩显示屏及相关高可靠性要求的应用场合。
特性:尺寸(mm):5.0x5.0mm 表面贴片发光二极管胶体颜色:透明发光颜色:七彩和白光发光角度:120°表面颜色:表面白色应用:ＬＥＤ面板灯，半户外和户外显示屏红绿蓝全彩屏产品在不断更新，建议有新产品代替时使用.产品参数：注意:所有尺寸单位为mm；如无特殊说明误差范围为±0.05mm 。
＊＊＊应用注意事项特点本文件主要向顾客及用户介绍怎样如何更好的使用我司的SMD LED 产品。
描述一般来说，SMD 5050跟一般的半导体有相同的用法。
当使用荧月电子的ＳMD5050产品，请遵从以下的使用方法以保护SMD LED 产品。
1.清洁：不要使用不明化学液体清洗SMD LED，不明的化学液体可能会损坏SMDLED。
当必要清洗时，把SMD LED沉浸在酒精里，在正常的室温下少于1 分钟并且自然干燥15 分钟，然后才开始使用。
2.防潮湿包装为避免产品在运输及储存中吸湿,SMD LED 的包装是用防潮的铝包装袋包装，并且包装袋里面含有干燥剂及湿度卡，干燥剂主要起到控制包装袋里的湿度，湿度卡主要是起到监控包装袋里的湿度。
3.储存a.包装袋密封后贮存在条件为温度< 40℃，湿度< 60%RH，保存期为12 个月。
当超过保质期时，需要重新烘烤。
b.在开包装之前，请先检查包装袋有无漏气或湿度指示卡有无变色，如果有漏气或湿度指示卡有变色现象，请重新烘烤后再使用。
c.开封后请在以下条件使用：温度< 30℃、湿度在30%RH 以下；如果使用时间超出24小时，须做以下烘烤处理才可使用。
d.烘烤条件：产品在烘箱在温度为70℃±5℃；相对湿度≤10%RH，时间:24 小时。
5050灯带规格书
特点•5M*10mm贴片软灯条（30L E D/M）.•印制电路板厚度：0.2mm•印制电路板宽度：10mm•工作电压：24V 直流.•工作电流:0.3A/M.•LED 可视角度(2θ1/2):120°•使用寿命：50000H•防水等级：IP20.应用户外照明：建筑装饰照明、标致照明、路径和轮廓标识、水下工程照明；广告照明：广告字的背光源、超薄灯箱、发光字、发光招牌；气氛照明：酒吧、KTV、咖啡厅等娱乐场所气氛渲染、工艺品照明。
室内装饰：高档专卖店、商铺等室内商业氛围照明、汽车装饰、楼梯走廊家居装饰照明；实物图静电敏感设备应用场景：LED 灯带3灯带参数光电参数压降说明：发光角度外形尺寸500010033.3310.00FPCSMD LED Res lstcr.501.753M stiker1. 所有的单位为 mm.2. 如无特殊说明，所有的公差均为3 .包装说明注意事项a)富晟LED灯带是静电敏感产品，应采取措施避免静电，诸如在使用过程中戴静电手环或防静电手套，所有的装置、设备仪器接地。
建议对组装后的LED灯带进行测试，确认LED灯带是否受到静电的破坏，确认方法为（参考）：低电流或低电压，LED不能点亮或同等条件下亮度较其他LED明显偏暗为缺陷品；b)LED灯带供电电压为12V，过长使用（超过5M）压降上升，导热尾部供电电压不足，造成LED亮暗不均匀，建议使用时，超过5米从中间供电或者两头供电；c)富晟LED灯带为柔性线路板，使用过程中请勿旋转折叠，以免造成线路破坏；d)LED灯带长时间暴露在阳光或偶尔暴露在紫外线下可能导致胶体黄变；e)为保证LED灯带光电性能，请保持LED灯带发光区域表面清洁，避免手指印或其它异物覆盖；f)富晟LED灯带自带双面胶，粘贴前需保证粘贴表面平整.干净.无油；g)富晟LED灯带自带双面胶粘性强，不可在粘贴后又拉起质量保证限制●在正常使用条件下的品质保证：是基于产品的正确保存、安装、使用和维护；●由于客户安装使用不当，违反产品操作规程，而引起的产品损坏；●未经授权的修改或误用；●在指定的环境外操作本产品，或是在非指定的维修点进行配置及维修；●客户自行安装的电路造成的损坏。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
确认后请回传,谢谢!Please confirm and fax to us ,thank you!
XL-5050 LED 硬灯条
产品效果展示：
LED 硬灯条 5050灯珠效果 LED 硬灯条 5050灯珠效果
一、 特点：
1、采用高亮度SMD5050 LED 灯珠 ， 铝合金外壳 ， 每三个LED 为一段。
2、每条的标准长度为1M ，每条灯珠数量分别有 30PCS/M LED 灯珠 ，60PCS/M LED 灯珠 ，72PCS/M LED 灯珠
3、发光颜色：红/绿/蓝/黄/白/暖白和长彩等多种颜色可供选择
4、工作电压：DC12V/DC24V 两种
5、防水型SMD 灯条，表面采用灌胶
二、 用途：
1、SMD 高亮度硬灯条适用于酒店，超薄灯箱，KTV 娱乐场所等室内装饰。
2、用于广告招牌等精品装饰领域。
3、度假装饰照明灯，显示及展览。
4、商场专柜，珠宝，首饰台及名贵钟表柜台。
三、产品规格：
四、参数
灯珠类型号： SMD 5050 LED 可选颜色： 红/绿/蓝/黄/白/暖白/RGB
发光角度: 120度 灯珠数量: 30PCS / M 60PCS / M 72PCS / M 外形尺寸: 1000*10*2mm 按整体封存装: 裸板 V 型槽 U 型槽
硬灯条套V 型槽图示
硬灯条裸板图示
U 型槽图示
五、 注意事项：
六、
产品应用
应用家居装饰
应用KTV 装饰
珠宝柜装饰
●使用说明use manual:
1.请先仔细阅读产品规格书,确认其使用环境是否符合规格书上的条件上,方可放心使用. Please read the specification
first to make sure the using condition is fit
2.将产品接入电源时,请先确保开关处于闭合状态..Please shut off the switch before connect the product, then turn on
3.本产品保质期为一年This product warranty for one year
4.。