LED便携应急灯规格说明书

合集下载

TH-ZH3W恒流型应急电源应急灯规格书

4.灯具工作电压交流 220V50Hz，请注意查看电源电压情况，如误接上 380V 三相电会烧毁灯具；
5.如灯具接上电工作不正常，要即刻切断电源，取下灯具维修；
⊙ 试验按钮功能 2
2.1.主电状态下按动试验按钮<5 秒为正常的模拟主电故障； 2.2.主电状态下按动试验按钮 1 次（绿指示灯按 1HZ 闪烁，即 1 秒钟闪烁 1 次）松开后进入手动月检，先主电 2 秒再放电 120 秒之后回到主电状态； 2.3.主电状态下连续按试验按钮 2 次（绿指示灯按 3HZ 闪烁，即 1 秒钟闪烁 3 次）再松开，电路进入手动年检，先主电 2 秒再放电终止回到主电状态； 2.4.主电状态处于月检或年检状态时，连续按动试验按钮 3 次即可回复到主电状态。 3.指示灯功能: 3.1.绿色指示灯长亮为主电状态。 3.2.红色指示灯长亮为充电状态，灯灭为停止充电状态，以 1HZ 的频率闪烁为月检状态，以 3HZ 的频率闪烁为年检状态。 3.3.黄色指示灯以 1HZ 的频率闪烁为电池开路丶充电回路断路状态；以 3HZ 的频率闪烁为光源开路丶光源断路或自检时应急无输出状态；长亮为自检时检测到电池放电时间不足。 4.故障报警功能: 4.1.当电路出现故障进入自检时未排除 2 秒内报警； 4.2.在自检过程中出现电池开路，充电回路短路，放电回路无输出、月检放电不足 120 秒以及年检放电不足 30 分钟则报警； 4.3.报警声每隔 50 秒提示一次，每次持续时间为 2 秒，报警声持续到故障排除为止。 4.4.当在自检过程中发现电池放电时间不足或光源故障时，此时要求排除故障后按动试验按钮巡检一次才能回到主电状态。 5.本灯具除设计手动月检和手动年检功能，还具有自动月检和自动年检功能。自动月检：在正常主电状态电路工作 48 小时后每隔 30 天±2 天自动由主电工作状态转入应急状态，并持续 120 秒，然后自动恢复到主电工作状态。自动年检：在正常主电状态电路工作每隔 1 年自动由主电工作状态转入应急工作状态并持续至放电终止然后自动恢复到主电工作状态。要加速测试自动月检和自动年检功能见本制造商提供的《频率加速测试月检年检功能的方法》 6.做好维护保养记录，定期进行对灯具维护保养。 7.定员定期检查，排除故障，以确保使用寿命和正常使用。

HLL系LED爆炸防护灯具说明书

MANUALHLL Series LED Explosion-protected Luminaire3. Safety InstructionsThis product should be installed, inspected, and maintained by a qualifiedelectrician only, in accordance with national regulation, including the relevantstandard and, where applicable, in acc. With IEC 60079-17 on electrical apparatus for explosive atmospheres.The national safety rules and regulations for prevention of accidents and the following safety instructions in these operating instructions, will have to be observed!The luminaire must not be operated in Zone0 and in Zone20!When using in Zone21,Zone22, the requirements of IEC/EN 60079-14 relating to temperature must be observed. The indicated surface temperatures are not related to a layers above 5 mm thickness.Do not install where the marked operating temperature exceed the ignition temperature of the hazardous atmosphere.Do not operate in ambient temperatures above those indicated on the luminaire nameplate.The luminaires shall be operated as intended and only in undamaged and perfect conditions! And Keep tightly closed when in operation! The technical data indicated on the luminaire are to be observed!!connection cable. Following their manufacturer instructions.Fig.1Ceiling mounting 1. DIMENSIONSFig.2Wall mountingFig.3Pipe mounting2. Technical dataHazardous area specificationType of protection:Ex d, e, i,m, tIEC Certification Marking:Ex db eb mb IIC Gb(Normal with switch)Ex db eb ib mb IIC Gb(EM with switch)Ex eb mb IIC Gb(Normal without switch)Ex eb ib mb IIC Gb(EM without switch)Ex tb IIIC T80℃DbATEX Certification Marking:II2 G Ex db eb mb op is IIC T6 Gb(Normal with switch)II2 G Ex db eb ib mb op is IIC T6 Gb(EM with switch)II2 G Ex eb mb op is IIC T6 Gb(Normal w/o switch)II2 G Ex eb ib mb op is IIC T6 Gb(EM without switch)II2 D Ex tb op is IIIC T80℃DbAmbient temperature:-40ºC~+55ºC/-25ºC~+55ºC Temperature class:T6IECEx Certificate No.:IECEx CQM 16.0030X temperature is -40ºC~+55ºC or -25ºC~+55ºC . Refer to the luminaire nameplate, For specific information, corresponding operating temperature(T-Code).The enclosure materials used, including any external metal parts, are High quality materials that ensure a corrosion resistance and resistance to chemical substances according to the requirements for use in a “normal“ industrial atmosphere. In case of use in an extremely aggressive atmospheres, please refer to manufacture.5. Conformity with standardsThis explosion protection floodlight meet the requirements of IEC/EN 60079-0, IEC/EN 60079-1, IEC/EN 60079-7, IEC 60079-11, IEC 60079-18, IEC/EN 60079-31. It also complies with the EC Directives for “Apparatus and protective system for use in explosion atmospheres” (2014/34/EU). It has been designed, manufactured and tested in accordance to the state of the art and according to ISO 9001:2008. The luminaires are suitable for use in explosive atmospheres, Zone1, Zone2 according to IEC60079-10-1 and dust area Zone21 and Zone22 according to IEC60079-10-2.7. Type configuration and Max. Ambient and Temperature RatingsStd. Cat No.ColorTemp.SystempowerLEDQty.T Class(Gas)T ℃(Dust)Voltage(V)Tamb.(ºC)Weight(kg)HLL-2-W-2L-D-*-*-*-*3000K4000K30W28T680110-240Vac50-60Hz108-250Vdc-40~+556HLL-2-W-2L-D-EM*-*-*-*-25~+557HLL-2-3L-D-*-*-*-*5000k5700K6500K -40~+556HLL-2-3L-D-EM*-*-*-*-25~+557HLL-4-W-4L-D-*-*-*-*3000K4000K60W56-40~+5510HLL-4-W-4L-D-EM*-*-*-*-25~+5512HLL-4-5L-D-*-*-*-*5000k5700K6500K -40~+5510HLL-4-5L-D-EM*-*-*-*-25~+55128. Installation8.1GeneralThe respective national regulations IEC/EN 60079-14 as well as the general rules of engineering which apply to the installation and operation of explosion protected apparatus will have to be observed!The improper installation and operation may result in the explosion protection and invalidation of the guarantee. 8.2 Mounting luminaire8.2.1 Mounting the bracketOnly use the accompanying mounting bracket! Securely fasten the mounting bracket to a suitable base with sufficient load-bearing capacity. The mounting should be secured with M8 bolts and relative lock washers, nuts should be used.The minimum distance between the luminaire and illuminated surface, directly in front of the luminaire, is 0.5 meter. The lamp must not be illuminated when at a distance of less than 0.5m from inflammable material8.3 Cable entries/Plugs and Breathing valve The “Increased safety (Exe)" properties must be preserved when select and mount cable entry/plug and breathing valve. Unused holes must be closed with certified plug to establish the Exe protection category. The cable glands/plugs and breathing valve should be Ex tb certified if the whole product is Ex tb certified also. Cable entries sealing washer(if required by manual of cable gland/plug) must be used to obtain IP66.The authoritative mounting guidelines for the cable glands and breathing valve used must be observed. Mounting the selected cable entries acc. type and dimensions of the main connection cable following their manufacturer instructions. The cable temperatures are given as the rise over the max. rated ambient (Tamb). This allows the user to adjust the cable specification for actual maximum site ambient. Only heat resistant cable according to the data on the type label may be used! The max. conductor size is 6mm². The standard looping cable size is 4mm².8.4 Opening/closing the luminaire8.4.1 GeneralThe opening of luminaire always shall be without voltage! All gasket seals must be clean and undamaged before closing the luminaire. Make sure the luminaires is well closed before operation!8.4.2 Exe chamber coverOpen the buckles and remove the PC cover. And carry out the steps in reverse order to close the luminaire. Check all buckles to ensure a secure fit during operation .8.5 Electrical connectionThe electrical connection of the lamp must only be established by qualified electricians.Make sure the supply voltage is the same as the luminaire voltage! Use proper supply wiring as specified on the nameplate of the luminaire and in this instructions! Excessive tightening may affect or damage the connection.8.5.1 Wire connectionThe conductors shall be connected with special care inorder to maintain the explosion category.The conductor itself shall not be damaged.The connectible min. and max. conductor cross-sections shall be observed (see technical data). Allterminals, used and unused, shall be fully tightened toprevent incorrect selection between 1.2Nm for Exe T6P and 1.5~1.8Nm for MBK. Main connection: Seewiring diagram. See Fig.4 for details.9. Putting into operationPrior to putting the apparatus into operation, the testsspecified in the relevant national regulations shall becarried out. Insulation measurements may only becarried out between PE and the external conductor L1(L2, L3) as well as between PE and N.-Measurement voltage: Max. 1.5 KV AC-Measurement current: Max.5 mA-The luminaire may only be operated when closed.-It is generally recommended (see IEC/EN 60079-14)that you ensure the type of protection of theconstruction is not impaired during installation.10. Maintenance/Servicing10.1 GeneralThe relevant national regulations which apply to themaintenance/servicing of electrical apparatus inexplosive atmospheres, shall be observed (EN/IEC60079-17). The interval between maintenance dependsupon the ambient conditions and the hours ofoperation. The recommendations given within EN/IEC60079-17 for recurring checks must be observed.10.2 ChecksThe equipment must be de-energised before openingVisual inspection should be carried out at a minimumof 12 monthly intervals and more frequently ifconditions are severe, refer to EN/IEC 60079-17. Thetime between lamp changes could be very infrequentand this is too long a period without inspection.10.3 Routine ExaminationDuring maintenance, the parts affecting the level ofprotection must be checked in particular:-Ensure the lamp is lit when energised and examine theenclosure and glass for any signs of cracks and damage.-When de-energised and left to cool, there should be nosignificant sign of internal moisture. If there are signs ofwater ingress, the luminaire should be opened up, driedout, and any likely ingress points eliminated by re-gasketing, re-greasing or other replacement.-Check the gasket of pc cover and LED housing for anydamage or permanent set and replace as required.-Terminal, screw glands and blanking plugs for securefitting.-To maintain the light output, clean the protective pccover periodically with a damp cloth or a mild cleaningfluid.-If this product is used in the combustible dust area,outside of enclosure must be cleaned on a regular basis toprevent accumulation of dust.-The cable connections should be checked for tightness.The gasket should be checked for cracks or lack ofelasticity, and if necessary, replaced.-Check that mountings are secure and the adjusting boltsare tight.-If it has been suspected that the luminaire has mechanicaldamage, a stringent workshop overhaul will be required.Where spares are needed, these must be replaced withfactory specified parts.No modifications should be made without the knowledgeand approval of the manufacturer.Cleaning the joint of housing assy. and pc cover use adamp cloth or a mild cleaning fluid.11. Repair/Overhaul/Modifications11.1 GeneralThe national regulations EN/IEC60079-19 have to beobserved! Repairs and overhaul may only be carried outwith genuine Eaton Crouse-Hinds spare parts.In the case of battery failure, the battery pack must bereplaced as a complete unit from the manufacture.Before replacing or disassembling individual parts, observethe following:Disconnect the power supply to the equipment beforemaintenance/repair.Make sure that there is no explosive atmosphere whenopening the equipment. See section 8.4 for notes onopening and closing the lamp.Only use original spare parts. If the luminaire waspreviously in operation then wait to cool enough beforeopening. Repairs that affect the explosion protection,may only be carried out by Eaton Crouse-Hinds or aqualified electrician in compliance with the applicablenational rules. Modifications to the device or changes toits design are not permitted.After carrying out repair or overhaul work, ensure thatthe “Exde" properties have not been affected.Assistance may also be obtained through CooperElectronic Technologies (Shanghai) Co., Ltd. Sales Servicedepartment,955 ShengLi Road, Pudong Shanghai 201201Phone (86) 21-2899394312. Disposal/RecyclingWhen the apparatus is disposed of, the respective nationalregulations on waste disposal will have to be observed. Fig4。

瑞丰LED光线灯具规格书说明书

and reliability.如产品需要用在有特殊质量要求及可靠性要求的地方，请提前咨询瑞丰的销售人员以取得相关信息。

disassemble and analyzein written form.在取得瑞丰的同意前，客户不应该对产品进行拆解分析，如发现失效产品，请直接书面通知瑞丰。

Features 特征Extremelywide viewing angle.发光角度大Suitable for all SMT assembly and solder process.适用于所有的SMT 组装和焊接工艺 Moisture sensitivity level:Level 3.防潮等级Level 3 Package:4000pcs/reel.包装每卷4000pcs RoHS compliant.满足RoHS 要求Description 描述The Colour LED which was fabricated by using a green chip 该产品为绿光LED ，是由绿光芯片封装形成Applications 应用Optical indicator.光学指示Switch and Symbol,Display.开关和标识、显示器等 General use.其他应用RF-GNS150TS-CFPackage Dimension外观尺寸NOTES:1.All dimensions units are millimeters.(所有尺寸标注单位为毫米)2.All dimensions tolerances are 0.2mm unless otherwise noted.(除特别标注外，所有尺寸公差为±0.2毫米)Electrical/Optical Characteristics at Ts=25°C电性与光学特性Note:备注Vr=5V For test conditions.Vr=5v为测试分选条件。

Chloride Compac LED紧急灯具CLU介绍及参数说明书

Chloride Compac LED emergency unit CLU features a low-profile, contemporary design with aesthetic appeal for many commercial applications. It was designed to be unobtrusive, but also deliveroptimum performance in treacherous situations. The two high-outputLED lamps are fully adjustable to meet your requirements.Ordering guideExample: CLUNWAccessories (order separately)• W G5 - Wire guard (for CLU emergancy unit mounted flat against the wall)DimensionsCLUPerformanceMeets Life Safety Code illumination standard; average of 1.0 FC, no point less than 0.1 FC, max to min ratio of 40:1. Assumes open space with no obstructions.†Based on 6ft corridor and 9ft ceiling height and a mounting height of 7.5ft.‡Based on 200ft by 200ft open area and 30ft ceiling height.Codes and standards• NFPA 70(National Electric Code)• NFPA 101(Life Safety Code)• ETL listed to Standard 924• UL Listed for damp locations Construction• Wall or ceiling mounted• UL 94 V-0.5VA Flame rated,UV stable thermoplastic housing • Provisions for surface mounted conduit to top of wall mounted unit• Back plate keyhole slots are easily removable knockouts for securing to single gang boxes, 3" J-boxes and 4" J-boxes for easy mountingInstallation• Designed for wall or ceiling mount with a universal J-box pattern on back plate• Surface conduit entry on top of housing in centerof backplate • CLU unit mounts to a standard single gang boxes, 3" J-boxes and 4" J-boxes for easy mountingElectronics• 120/277VAC, 50-60Hz dual voltage selectable input• Surge protected, solid state circuitry• Charging systems are complete with low voltage disconnect (prevents deep dischargeof battery), battery lockout (prevents discharge of battery during installation), and brownout protection Power consumptionCLU 120V = 0.027CLU 277V = 0.026Lamps• CLU unit contains 2 - 1Wadjustable LED lampheads (5000k)Battery• Maintenance-free sealed 3.6VNickel Cadmium battery• Manual test switch and LEDlight indicator• Supplies emergency illuminationfor a minimum of 90 minutes• Operating temperature range:Batteries have an approximatedservice life of 6 to 8 years at aoperating temperature range of10°C to 40°C (50°F to 104°F)Remote capabilityThe CLU Series units do not havethe capacity for remote capability.Listings• California Energy Commission,Title 20 compliant (BatteryCharger)Warranty• Five year full warranty on unit.Self-diagnostics/Self-testThe CLU units contain self-diagnostic/self-test electronicsas a standard feature. Anautomatic self-test is performedevery month for 3 minutes, anda 30 minute self-test every sixmonths. A manual test may also beperformed at anytime by pressingthe manual test button.Manual testing:Test button Length of test1 press30 seconds2 presses3 minutes3 presses30 minutes4 presses90 minutesSelf-Diagnostic Red status indicator:Indicator StatusOne blink Battery is notconnectedTwo blinks Battery voltage hasdropped belowacceptable valueThree blinks Charger boardcir faultFour blinks Transfer faultFive blinks Lamp faultSix blinks Remote lamphead faultSeven blinks EXIT Led strip faultThe Self-diagnostic/self-test electronics meets therequirements of the NationalElectric Code and/or the NationalFire Protection Association.© 2019 Signify Holding. All rights reserved. This document contains information relating to the product portfolio of Signify which information may be subject to change. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. All trademarks are owned by Signify Holding or their respective owners.Signify North America Corporation200 Franklin Square Drive,Somerset, NJ 08873Telephone 855-486-2216Signify Canada Ltd.281 Hillmount Road,Markham, ON, Canada L6C 2S3Telephone 800-668-9008The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract.。

应急灯说明书

五、电池与光源的使用与更换：警告：本灯具内部线路板带有220V/50HZ的高压，非专业人士不许拆开灯具！1、电池：正常情况下，在充电24小时后放电时间小于90分钟或电池漏液时，请更换电池。

如要更换电池则应断开电源，拆开灯具，拔下电池插头，更换新的相同规格型号电池则可。

正常情况下，电池寿命可达三年以上。

2、光源：采用LED灯珠，在应急时LED不亮更换灯珠，更换时,先断开电源，拆开灯具，换上相同规格型号灯珠则可。

六、安全使用方法与维护事项：1.使用前必须详细阅读此说明书，方可让灯具接上市电。

2.一般安装在楼梯间、通道、出口等醒目处，不允许露天安装。

3.此灯具主电源应进行单独开关控制，不受其他灯具及家用电器的电源控制开关的影响。

4.灯具工作电压交流220V50Hz，请注意查看电源电压情况，如误接上380V三相电会烧毁灯具。

5.如灯具接上电指示灯工作不正常，要即刻切断电源，取下灯具送维修。

6.绿色指示灯为主电指示，红色指示灯为充电指示，出现故障时黄色指示灯亮。

七、安装调试以及维护保养：2.按键功能：2.1.按动试验按钮<3秒为正常的模拟主电故障；2.2.持续按动试验按钮4秒（绿指示灯按1HZ闪烁，即1秒钟闪烁1次）松开后进入手动月检，先主电2秒再放电120秒之后回到主电状态；2.3.持续按试验按钮5秒（绿指示灯按3HZ闪烁，即1秒钟闪烁3次）再松开，电路进入手动年检，先主电2秒再放电终止回到主电状态；2.4.断开主电灯具处于应急状态，持续按动试验7秒即可关断应急输出。

3.指示灯功能：3.1.绿色指示灯长亮为主电状态，以1HZ的频率闪烁为月检状态，以3HZ的频率闪烁为年检状态。

3.2.红色指示灯长亮为充电状态，灯灭为停止充电状态。

3.3.黄色指示灯以1HZ的频率闪烁为电池开路丶充电回路断路状态；以3HZ的频率闪烁为光源开路丶光源断路或自检时应急无输出状态；长亮为自检时检测到电池放电时间不足。

4.故障报警功能:4.1.当电路出现故障进入自检时未排除2秒内报警；4.2.在自检过程中出现电池开路，充电回路短路，放电回路无输出、月检放电不足120秒以及年检放电不足30分钟则报警；4.3.报警声每隔30秒提示一次，每次持续时间为2秒，报警声持续到故障排除为止。

消防应急照明灯安装使用说明书

消防应急照明灯安装使用说明书1、概述本产品采用GB17945-2010标准，以LED为照明的应急灯，具有最新高科技产品，LED为发光，发光清晰，光色柔和，功耗极低，寿命长等特点，是当前一般灯管型应急照明的升级换代产品。

2、技术参数防护等级：≥IP30额定工作电压/频率：AC220V/50HZ应急时间≥90分钟应急输出光通量：≥501m应急转换时间：≤1秒主电功率：2W电池种类：Ni-Cd镍镉电池保险丝规格：交流1A 直流5A光源名称：发光二极管电池规格：Ni-Cd AA800mAh/2.4V光源输出参数：0.8W3、安装方法：吊装、壁挂，吊装用吊链吊在拉手上，壁挂挂在灯箱后面的瓜子形孔上。

4、使用方法：1、接线方法：棕色线接火线，蓝色线接零线，黄绿色接地注：棕色线、蓝色线不能接任何开关。

2、把本产品插上交流220V电源（充电18小时）此灯具主电绿色指示灯亮起，LED正常发光，a．用手按住试验开关2s进入试验状态，指示灯熄灭而LED仍然发光则表示应急工作正常；b．按住试验开关4s绿色指示灯1HZ闪烁，进入月自检模拟状态，自检通过转入主电状态。

c．按住试验开关6s绿色指示灯3HZ闪烁，进入年自检模拟状态，自检通过转入主电状态。

3、平时该消防应急灯具不点亮，应急才点亮；应急状态按住试验开关大于6s关断应急。

5、日常维护1、试验按钮用来模拟停电、月自检、年自检之用，以检测灯具应急工作是否正常，用户应按消防部分要求进行检测和维护。

2、灯具出厂内部电源于放空状态，使用前应先充电24小时，充电时充电灯亮起，接近充满红色指示灯熄灭，此时电路进入浮充对电池小电流充电。

3、声光报警1（故障灯黄灯1HZ闪烁，蜂鸣器1min/1次），表示该灯充电回路短路或者开路；检查保险丝或电池，并及时修理。

4、声光报警2（故障灯黄灯3HZ闪烁，蜂鸣器1min/1次），表示该灯光源短路，开路或应急回路断开；检查光源或应急回路，并及时修路。

消防应急灯具产品规格书

YYJD-ZZ-66 应急灯技术参数产品型号功率输入电压应急时间充电时间应急转换时间YYJD-ZZ-66 6W AC220V ＞90min ＜24h ＜0.5sec特点■采用开关电源控制电路，性能稳定，能适应宽松电压环境。

■微处理集中控制技术，美国FAIRCHILD PWM IC稳压技术。

■恒流恒压充电技术，有效提升电池使用寿命。

■智能故障自动检测，性能稳定■采用LED光源，节能环保，使用寿命长。

■采用优质镍镉电池，电池容量大。

■采用贴片工艺，产品质量稳定。

安装方式壁挂、手提YYJD-ZZ-68应急灯技术参数产品型号功率输入电压应急时间充电时间应急转换时间YYJD-ZZ-68 2W AC220V ＞90min ＜24h ＜0.5sec特点■采用开关电源控制电路，性能稳定，能适应宽松电压环境。

■微处理集中控制技术，美国FAIRCHILD PWM IC稳压技术。

■恒流恒压充电技术，有效提升电池使用寿命。

■智能故障自动检测，性能稳定■采用LED光源，节能环保，使用寿命长。

■采用优质镍镉电池，电池容量大。

■采用贴片工艺，产品质量稳定。

安装方式壁挂、手提YYJD-BZ-R标志灯技术参数产品型号功率输入电压应急时间充电时间应急转换时间YYJD-BZ-R 1W AC220V ＞90min ＜24h ＜0.5sec特点■采用优质镍镉电池，电池容量大，可连续充放电500-1000次■采用LED光源，节能环保，使用寿命长，可达100000小时■采用开关电源控制电路，性能稳定，能适应宽松电压环境■采用优质氧化铝材，超薄设计，外形美观结构形式壁挂式、吊装式YYJD-标志灯技术参数产品型号功率输入电压应急时间充电时间应急转换时间YYJD-BZ-LQ 1W AC220V ≥90分钟＜24h ＜0.5sec特点■采用优质镍镉电池、电池容量大、可连续充电500-1000次；■采用LED光源、节能环保；■使用寿命长、可达100000小时；■采用开关电源控制电路、性能稳定、能适用宽松电压环境；■采用优质氧化铝材、超薄设计、外形美观。

INL-03XLED灯应急电源规格书

7.3、测试开关
开关状态
功能
模式
按下<3 秒
模拟断电测试
按下 3-5 秒
模拟自检/月检功能①
主电
按下>5 秒
模拟自检/年检功能①
按下<6 秒按下>6 秒
关闭/打开应急输出② 彻底关闭应急输出③
电池
注①：模拟月/年检状态下，再次按下测试开关，取消模拟自检功能。月检/年检状态下无效。
注②：(手动应急控制）须电池组有正常的电量和市电触发后有效。
INC-032 86010032 LED 灯具
40-80 220~AC 50/60 Max 6 11.1/12
-25 45 70 -25—70
Data 13/07/14 INC-03X_SPEC V1.1_CN 如有更改恕不另行通知
2/5
5.2、电池尺寸（A2 型 / 连接线长：150-170 mm）
INL-03X LED 灯应急电源规格书
六、安装布线 6.1、接线图
N L
LED灯具
照明开关
OUT
OUT
N
L1
INC-03X
L
Bat Bat + LED/K LED/A Switch Switch
12V电池组 LED指示灯测试开关
6.2、连接线类型及截面积使用单芯线或多股绞合线，截面 0.75mm²-1.5mm²的铜芯线布线。线端剥开 6-8mm 的裸线（右图），确保完好的接入本控制装置的接线端子并压紧。 6.3、布线注意事项功率 LED 的连接线会增加损耗应尽量短些，推荐灯的连线使用小于 3 米的铜芯线连接。指示灯及测试按钮的连线应小于 1 米。墙壁照明开关(L 和 L1 之间)，其布线时须在同一相线上，布线距离应小于 100 米。推荐使用小于 50 米的铜芯线连接。为安全的使用本控制装置及避免损坏本控制装置，请勿将两路相线接入本控制器。LED 光源为有极性光源，请勿将极性接错，以免导致故障及额外的损失。为正确安全的使用本控制装置，请严格按照接线图正确接线（见 6.1 节）。 6.4、安装推荐本产品拥有良好的热处理单元，为保证产品性能、可靠性及使用寿命，应使本产品拥有良好的散热条件及使用环境。为确保良好的散热，应使本产品的底部良好的安装在金属板上或远离发热源，使本产品工作环境温度控制在允许的范围内。 6.5、电磁干扰 ● 不要将电源输入线和灯连接线交叉布线。 ● 尽量不要将电源输入线和灯连接线长距离平行布线，平行布线时应留 5-10cm 的距离。 ● 不要将电源输入线太贴近本控制装置。 ● 弯曲灯连接线。 ● 缩短电源输入线到本控制装置的连线距离。 ● 并联多个运行时应使电源输入线和灯的连接线尽可能短。

HW-ZFJC-E3W-N650消防应急照明灯具说明书

N600(Ver1.06，2020.07)一、注意二、概述本说明书为 2 线制集中电源集中控制型消防应急照明灯具（以下简称照明灯）综合说明书，包括以下产品:HW-ZFJC-E3W-N650（3W 嵌顶安装）、HW-ZFJC-E6W-N651（6W 嵌顶安装）、HW-ZFJC-E9W-N652（9W 嵌顶安装）、HW-ZFJC-E3W-N660（3W 壁挂安装）、HW-ZFJC-E6W-N661（6W 壁挂安装）。

照明灯通常安装于室内，有 2 种工作状态：正常，应急。

具有故障检测功能，故障信息通过总线上传到应急照明分配电装置，应急照明分配电装置再上传到应急照明控制器。

照明灯采用电子编码方式，可通过我公司生产的GST-BMQ-2 型电子编码器进行现场编码。

三、特点1. 受应急照明控制器的控制可使照明灯改变工作状态。

1. 照明灯的光源故障、通讯故障可在应急照明控制器上显示。

四、技术特性1. 总线电压：36V，允许范围：25V～DC36V2. 各型号功耗光通量如下表。

型号功耗W 光通量lmHW-ZFJC-E3W-N650 3 ≥120HW-ZFJC-E6W-N651 6 ≥200HW-ZFJC-E9W-N652 9 ≥350HW-ZFJC-E3W-N660 3 ≥90HW-ZFJC-E6W-N661 6 ≥2003. 光源类型，应急时间：LED，不小于90min，应急时间由集中电源的配置确定。

LED 光源的规格：DC2.9V～DC3.1V/0.2W；LED 光源的型号：2835W80N03。

4. 故障检测：光源出现短路、断路时，总线电压过低时，照明灯发送故障信号。

5. 编码方式：采用电子编码方式，占用一个地址6. 使用场所：室内相对湿度95%，不凝露7. 使用环境：温度：0℃～+55℃ ≤8. 防护等级：IP309. 外形尺寸、安装孔距、重量、壳体材料及颜色：型号外形尺寸（mm）安装尺寸（mm）重量g 壳体材料颜色HW-ZFJC-E3W-N650 Φ142×65 开孔直径Φ120 190 铝合金+ABS+PC 白色HW-ZFJC-E6W-N651 Φ173×66 开孔直径Φ145 270 铝合金+ABS+PC 白色HW-ZFJC-E9W-N652 Φ173×66 开孔直径Φ145 290 铝合金+ABS+PC 白色HW-ZFJC-E3W-N660 209×119×76 60 370 ABS+PC 白色HW-ZFJC-E6W-N661 209×119×76 60 370 ABS+PC 白色10. 执行标准：GB 17945-2010五、结构特征与工作原理1. 照明灯按安装方式可分为2 大类：a) 壁挂照明灯，外形示意图如图1 所示。

Velos LED紧急出口灯系列说明书

• Unit with innovative LED technology certiﬁed family of emergency exit signs in accordance to EN 60598-2-22• 3rd party certiﬁcation• Nickel Metal Hydride Batteries • Push button for test operation• Ceiling, wall, suspension, recessed and lateral installation• Models of 30m and 40m visibility • Test functionsThe Velos family of emergency lighting is designed and equipped with technical solutionsthat make it suitable for a wide range of applications. A complete range of accessories such as the recessed base for false ceiling installations, lateral and back base as well as suspension options allow for a variety of mounting positions.Together with the choice of ISO and EURO exit sign labels, the Velos LED range is appropriate for emergency lighting requirements in multiple of places such as ofﬁces, restaurants, hotels, hospitals and general commercial applications.Light Source:LED Strip with a lifetime of more than 60,000 hours 24 LEDs producing 140 lumens Materials:Base and reﬂector unit in white Polycarbonate Operation:Maintained, slave and CBS models available Autonomy from 3hAdjustable brightness function to 50% in mains operation Functional test button Telecommand, Inhibition operation Autotest and Slave models available Installation:Ceiling, wall, recessed,suspended through rope or me-tal pipe and lateral installation No special tools required Applications:Schools, universities, public administration, commercial environments Hotels, restaurants, meeting rooms, ofﬁces, shops,cinemas, theaters, museums Areas with large heights and long distance viewrequirementsViewing distanceMaximum viewing distance: 30/40m .Distance view of 30 / 40 meters provides the ability to use fewer products and less power consumption per coverage area of an application.224mm346mm69mm7Power Supply Unit• Easy to install with no use of special tools required.• Environmentally friendly: no heavy metals and energy-op-timized charging process due to low self-discharge.• Easy to connect power cables via screwless connectorsfor up to 2.5mm 2cables.• Multiple entrance points for power cables through base andmain body of the power supply unit.• Construction Material: Polycarbonate.• Large capacity NiMH batteries with small construction sizefor compact luminaire design.Velos electronics• Fully automatic function test (weekly) or duration test (every 10 weeks).• Testing button for manual triggering of function test.• Autotest models available with simple fault analysis with two LED indication of battery / LED test and statusdisplay (operation, function test, duration test, failure).• Easily set the level in mains operation to 50% or 100%.• Increased product reliability with LED matrix orientation. By groups of 3, if one of the 24 LEDs fails,the intact LEDs will illuminate more brightly.Velos distance view• Velos provides a solution regarding distance view and emergency exit signs • Distance view from 30 up to 40 meters, minimizing the number of lights into an installation, reducing the energy consumption of the emergency lighting in a building and installation and maintenance cost.• Various accessories for ease of installation aiming to accommodate all possible applications and areas, with recessed base, wall mounting accessories, lateral direction base, suspended from ceiling either with rope or metal pipes.Velos optimal illuminationThe exit sign plate used in Velos converts the high luminance of the LED into an illuminated surface with homogeneous bright-ness, with luminance of over 38 cd/m 2 on the white surface. As such the escape sign always remains easily recognisable even with poor visibility conditions or in bright surroundings.Velos LEDs illuminate with a high efﬁciency of more than 112lm/W.Velos Exit Sign • Design life time: exceeding 60.000 hours lifetime expectancyusing an EN1838 standard plate of 4mm thickness with 24 LEDproducing 140lm with minimum 240 cd/m 2 on white surface.• Simple parts clicking with each other ensuring fast installation.Photometric requirements for escape sign EN 1838 (1999), Emergency lighting operation:Lmin = 2 cd/m 2 (green surface) Lgreen ≥ 2 cd/m 2Lwhite ≥ 10 cd/m 25 ≤ Lwhite / Lgreen ≤15ISO 30061 (2007), When smoke is prime consideration:Lgreen ≥ 10 cd/m 2Lwhite ≥ 50 cd/m 2Distance view of 20m.Distance view of 40m.22112233344556667PSU unit of Velos (order separately)O-ESC-3H Velos PSU 3h3h 4VTCs NiCd 1600mA O-ESM-AT -3H Velos PSU 3h Auto Test 3h 4VTCs NiMH 2000mA O-ESC-3H-CGL Velos PSU, 3h, CGL+ 3h 4VTCs NiCd 1600mAO-ESMAINSVelos 230V Mains SlaveO-ES-CG-SVelos 220/230V Mains Slave CG-SOrder code Description AccessoriesOrder code DescriptionO-ESA-RB Velos Recessed base O-ESA-FLEX Velos Wall FLEXI JointO-ESA-RSA Velos Wire suspension adjustable 150cm O-ESA-RSA-5M Velos Wire suspension adjustable 5m O-ESA-PS30 Velos Pipe Suspension 48cm (ISO30061) O-ESA-LMB Velos Lateral Mounting Base O-ESA-BMBVelos Back Mounting BaseVelos+Recessed Base (O-ESA-RB)Recessed (30m)PSU+Exit sign 40m (O-ESP40-IDD)Ceiling mount (40m)Velos+PSU +Recessed Base (O-ESA-RB)+Exit sign 40m (O-ESP40-ILR)Recessed (40m)Velos+Pipe Suspension 48cm (ISO30061)(O-ESA-PS30)Suspended with metal pipesVelos+Velos Wire suspensionadjustable 150cm (O-ESA-RSA)Suspended with adjustable ropeadjustable to 150cmCeiling mountPSU + Exit Sign VelosVelos+Wall FLEXI Joint (O-ESA-FLEX)Wall mount Velos+Back mounting Base (O-ESA-BMB)Back wall mountVelos+Lateral Base (O-ESA-LMB)Lateral mount 7O-ESP-H Velos Hydrant pictogram 30m 24 LEDs 288x165Exit sign of VelosOrder code Description DimensionsOrder code Description DimensionsO-ESP40-ILR Velos pictogram ISO LEFT/RIGHT 40m 24 LEDs 370x220 7。

EATON SafeLite 紧急灯具说明书

SafeLiteFunction Use either as an emergency luminaire or exit sign Testing system Stand AloneRest Mode Possibility to switch off the luminaire when operating on battery mode (TLU)HousingPolycarbonate, Glow wire test : 850°C, RAL9003Type of mounting SurfaceOptions : see accessories pageTerminalsup to 2.5 mm² (connector type depending on product variant)Degree of protection IP42/IK04 or IP65/IK07Operation Mode Non Maintained or Maintained & Non Maintained mode selectable Connection voltage 230V -/+ 5% [220V-240V] 50-60Hz Permissible ambient temperature +5°C to +40°C Battery Ni-Cd Light source LED strip Viewing distance 20m or 30m Insulation class IIDimensions in mm 20 m viewing distance version: 270 x 119 x 4930 m viewing distance version: 371 x 170 x 62Lighting performanceSee photometric data pagesSafeLite 20m49 mm 270 mm119 m mSafeLite 30mWire guard :Recessed base:Cone Diffuser:Plexi Diffuser:Recessed box:Safelite self-contained luminaires • Compliant with EC standards • EN certiﬁed• All applications covered (Escape route, Anti-panic, Exit sign)• One product throughout installation for same look and feel across the building • Accessories available for a better integration in all buildings• Easily installed as retro ﬁt due to good performance ensuring scheme compliance • 1h, 2h & 3h Duration• Latest generation LEDs with high lumen/watt ratioConsumptionOrder code V i e w i n g d i s t a n c e (m )I PI KD u r a t i o n (h )L u m i n e m e r g e n c yL u m i n m a i n sO p e r a t i o nN M V AN M WM V AM WB a t t e r yW e i g h t (k g )A d h e s i v e E x i t L e g e n d i n c l u d e d SL2MNM42C1C3A 20420416060MNM 2,72,62,82,73,6 V 0.8 Ah 0.5ISO (L, R, D)SL2MNM42D1C3A 204204110060MNM 2,52,42,62,53,6 V 0.8 Ah 0.5ISO (L, R, D)SL2MNM65C1C3A 20650716060MNM 2,72,62,82,73,6 V 0.8 Ah 0.5ISO (L, R, D)SL2MNM65D1C3A 206507110060MNM 2,52,42,62,53,6 V 0.8 Ah 0.5ISO (L, R, D)SL2NM42D12042041100-NM 1,40,9--3,6 V 0.8 Ah 0.5SL2MNM42E1C3A 204204115060MNM 2,72,62,82,73,6 V 0.8 Ah 0.5ISO (L, R, D)SL2MNM42F1C3A 204204120060MNM 2,52,42,62,53,6 V 0.8 Ah 0.5ISO (L, R, D)SL2MNM65E1C3A 206507115060MNM 2,72,62,82,73,6 V 0.8 Ah 0.5ISO (L, R, D)SL2MNM65F1C3A 206507120060MNM 2,52,42,62,53,6 V 0.8 Ah 0.5ISO (L, R, D)SL2MNM42H1C 204204130060MNM 3,22,53,83,23,6 V 1.7 Ah 0.7SL2MNM65H1C 206507130060MNM 3,22,53,83,23,6 V 1.7 Ah 0.7SL2MNM42C2C3A 20420426060MNM 2,72,62,82,73,6 V 0.8 Ah 0.5ISO (L, R, D)SL2MNM42D2C3A 204204210060MNM 2,52,42,62,53,6 V 0.8 Ah 0.5ISO (L, R, D)SL2MNM65C2C3A 20650726060MNM 2,72,62,82,73,6 V 0.8 Ah 0.5ISO (L, R, D)SL2MNM65D2C3A 206507210060MNM 2,52,42,62,53,6 V 0.8 Ah 0.5ISO (L, R, D)SL2MNM42D2C 204204210060MNM 2,52,42,62,53,6 V 0.8 Ah 0.5SL2MNM42F2C 204204220060MNM 3,22,53,83,23,6 V 1.7 Ah 0.6SL2MNM65D2C 206507210060MNM 2,52,42,62,53,6 V 0.8 Ah 0.5SL2MNM65F2C 206507220060MNM 3,22,53,83,23,6 V 1.7 Ah 0.6SL2MNM42D3C3A 204204310060MNM 3,22,53,83,23,6 V 1.7 Ah 0.6ISO (L, R, D)SL2MNM65D3C3A 206507310060MNM 3,22,53,83,23,6 V 1.7 Ah 0.7ISO (L, R, D)SL2NM42D32042043100-NM 1,71,4--3,6 V 1.7 Ah 0.5SL2MNM42E3C3A 2042043150 60MNM 3,22,53,83,23,6 V 1.7 Ah 0.6ISO (L, R, D)SL2MNM42F3C3A 204204320060MNM 3,22,53,83,23,6 V 2 Ah 0.6ISO (L, R, D)SL2MNM65E3C3A 206507315060MNM 3,22,53,83,23,6 V 1.7 Ah 0.7ISO (L, R, D)SL2MNM65F3C3A 206507320060MNM 3,22,53,83,23,6 V 2 Ah 0.7ISO (L, R, D)SL2MNM42C3C 20420436060MNM 2,72,62,82,73,6 V 0.8 Ah 0.5SL2MNM42D3C 204204310060MNM 3,22,53,83,23,6 V 1.7 Ah 0.7SL2MNM65C3C 20650736060MNM 2,72,62,82,73,6 V 0.8 Ah 0.5SL2MNM65D3C 206507310060MNM 3,22,53,83,23,6 V 1.7 Ah 0.7SL2MNM42C3D 204204360100MNM 4,54,44,84,63,6 V 0.8 Ah 0.6SL2NM65D32065073100-NM 1,71,4--3,6 V 1.7 Ah 0.6SL3MNM42E1C3A 304204115060MNM 2,72,62,82,73,6 V 0.8 Ah 0.7ISO (L, R, D)SL3MNM42F1C3A 3042041200 60MNM 2,52,42,62,53,6 V 0.8 Ah 0.7ISO (L, R, D)SL3MNM65E1C3A 306507115060MNM 2,72,62,82,73,6 V 0.8 Ah 0.7ISO (L, R, D)SL3MNM65F1C3A 306507120060MNM 2,52,42,62,53,6 V 0.8 Ah 0.7ISO (L, R, D)SL3MNM42E3C3A 304204315060MNM 3,22,53,83,23,6 V 1.7 Ah 0.9ISO (L, R, D)SL3MNM42F3C3A 304204320060MNM 3,22,53,83,23,6 V 2 Ah 0.9ISO (L, R, D)SL3MNM65E3C3A 306507315060MNM 3,22,53,83,23,6 V 1.7 Ah 0.9ISO (L, R, D)SL3MNM65F3C3A 306507320060MNM 3,22,53,83,23,6 V 2 Ah 0.9ISO (L, R, D)SL3MNM42F3C 304204320060MNM 3,22,53,83,23,6 V 2 Ah 0.9SL3MNM65F3C306507320060MNM3,22,53,83,23,6 V2 Ah0.9Order codesRecessed Base 20m Dimensional drawings (mm)Cone Diffuser 20m Dimensional drawings (mm)Recessed Base 30m Dimensional drawings (mm)Cone Diffuser 30m Dimensional drawings (mm)SafeLite 20m Exit Sign Plexiglass drawings (mm)SafeLite 30m Exit Sign Plexiglass drawings (mm)AccessoriesWire guard - ensures high degree of protectionSL2PG SafeLite 20m, Wire guardO-EL-GRID SafeLite 30m, Wire guardRecessed base - For full recessed mounting, compatible IP42 & IP65 variants, can be associated to double side diffusersSL2RB SafeLite 20m,RecesBaseSL3RB SafeLite 30m,RecesBaseRecessed boxSL2WB SafeLite 20m,Wall BaseOpal diffuserSL2OP SafeLite Opal Diffuser**Wall bracketEL-BR1SafeLite 20m, 90° Wall BracketDouble side cone diffuser - compliant with EN1838SL2CD SafeLite 20m,Cone Diffuser*SL3CD SafeLite 30m,Cone Diffuser*Double side plexi diffuserSL2PPD SafeLite 20m,Plexi Plate, one side, DownSL2PPDD SafeLite 20m,Plexi Plate, double side, DownSL2PPLR SafeLite 20m,Plexi Plate, double side, Left & RightSL3PPD SafeLite 30m,Plexi Plate,one side, DownSL3PPDD SafeLite 30m,Plexi Plate,double side, DownSL3PPLR SafeLite 30m,Plexi Plate, double side, Left & RightLUM10312Remote control box - TLU 2*Pictograms have to be ordered separately (or re use ones delivered with luminaires).**Light decrease around 5%, mesured values upon request 00Light distribution curvePhotometric data - 20m version, 60 lm Escape route 2m wide 1 lux minMounting height [m]2,53,42,56,66,42,42,82,72,46,76,62,43,02,32,36,86,72,33,51,72,16,86,72,14,01,31,76,66,51,74,51,00,86,36,20,8Open (anti-panic) area 1 lux minMounting height [m]2,52,25,95,72,12,82,26,15,82,13,02,26,15,92,13,52,16,26,12,04,01,76,26,21,64,51,16,26,71,0Open (anti-panic) area 0.5 lux minMounting height [m]2,52,97,26,92,82,83,07,57,22,93,03,07,77,42,93,53,07,97,82,94,02,98,38,22,84,52,88,58,52,7Light distribution curvePhotometric data - 20m version, 100lmEscape route 2m wide 1 lux minMounting height [m]2,55,73,17,87,73,12,84,63,28,28,03,13,04,03,28,48,23,13,52,93,28,88,53,14,02,23,08,98,63,04,51,82,88,98,72,85,01,42,58,88,62,4Open (anti-panic) area 1 lux minMounting height[m]2,52,76,96,62,62,82,77,16,92,63,02,87,37,02,73,52,87,77,42,74,02,77,97,72,64,52,58,18,02,45,02,38,28,22,2Open (anti-panic) area 0.5 lux minMounting height[m]2,53,37,78,03,32,83,48,68,63,33,03,58,98,83,43,53,69,79,73,54,03,710,110,03,64,53,710,510,33,65,03,610,710,63,6Mounting height for 5 lux below 2.8 metersLight distribution curvePhotometric data - 20m version, 150lm Escape route 2m wide 1 lux minMounting height [m]2,58,03,58,68,63,42,86,43,69,19,03,53,05,53,79,39,23,53,54,03,89,89,63,74,03,13,710,19,93,74,52,53,610,310,13,65,02,03,410,510,23,45,51,63,110,410,33,16,01,42,710,210,12,76,51,12,19,99,82,07,01,00,99,59,50,9Mounting height [m]2,53,17,37,13,02,83,27,57,43,13,03,27,77,63,13,53,28,28,03,14,03,18,88,63,04,53,19,18,93,05,02,99,49,32,85,52,89,59,42,76,02,69,59,62,46,52,09,59,82,17,01,09,510,61,1Open (anti-panic) area 0.5 lux minMounting height [m]2,53,78,58,63,62,83,79,29,63,73,03,89,59,73,83,54,010,310,33,94,04,110,810,84,04,54,211,411,34,15,04,212,011,94,15,54,212,512,44,16,04,112,712,64,16,54,113,012,94,07,04,013,313,23,97,53,813,313,43,78,03,513,513,53,58,53,113,514,03,19,02,813,514,32,8Mounting height for 5 lux below 3.3 metersLight distribution curvePhotometric data - 20m version, 200lm Escape route 2m wide 1 lux minMounting height [m]2,510,03,98,79,23,72,88,04,09,49,73,93,07,04,09,89,93,93,55,14,110,810,54,14,03,94,211,211,04,04,53,14,211,511,24,15,02,54,111,711,44,05,52,03,911,811,63,86,01,73,711,811,63,66,51,53,311,611,53,37,01,32,811,411,32,7Open (anti-panic) area 1 lux minMounting height [m]2,53,27,97,83,12,83,38,38,13,23,03,48,58,33,33,53,59,48,93,34,03,59,79,43,44,53,510,09,83,45,03,410,410,13,35,53,310,610,33,26,03,210,710,53,16,52,910,810,72,87,02,510,811,02,4Open (anti-panic) area 0.5 lux minMounting height [m]2,53,99,19,53,72,84,19,49,83,93,04,19,710,14,03,54,311,010,94,24,04,511,811,64,44,54,612,612,44,55,04,713,012,84,65,54,713,413,14,66,04,713,713,54,66,54,614,113,94,67,04,514,614,34,4Mounting height for 5 lux below 3.7 metersLight distribution curvePhotometric data - 30m version, 100lm Escape route 2m wide 1 lux minMounting height [m]2,55,23,07,57,52,92,84,23,08,07,83,03,03,63,18,38,03,03,52,73,08,58,22,94,02,12,88,68,42,84,51,62,68,58,42,55,01,32,18,38,22,0Open (anti-panic) area 1 lux minMounting height [m]2,52,66,66,42,62,82,66,96,72,63,02,77,16,82,63,52,77,37,02,64,02,67,67,32,54,52,47,77,42,35,02,17,77,52,0Open (anti-panic) area 0.5 lux minMounting height [m]2,53,47,47,33,42,83,57,97,83,43,03,58,38,23,43,53,59,29,13,44,03,69,99,63,54,53,610,59,93,55,03,510,810,33,55,53,410,810,53,46,03,310,810,63,36,53,010,910,83,07,02,710,910,82,7Mounting height for 5 lux below 2.6 metersLight distribution curvePhotometric data - 30m version, 150lm Escape route 2m wide 1 lux minMounting height [m]2,57,43,58,08,23,42,86,03,68,68,63,53,05,23,69,08,93,53,53,83,79,89,53,64,03,03,710,09,83,64,52,33,510,29,93,45,01,93,310,210,03,2Open (anti-panic) area 1 lux minMounting height[m]2,53,27,97,83,12,83,38,38,13,23,03,48,58,33,33,53,59,48,93,34,03,59,79,43,44,53,510,09,83,45,03,410,410,13,35,53,310,610,33,26,03,210,710,53,16,52,910,810,72,87,02,510,811,02,4Open (anti-panic) area 0.5 lux minMounting height [m]2,53,16,96,93,02,83,17,57,33,03,03,17,87,53,03,53,18,38,13,14,03,28,78,33,14,53,18,98,63,05,02,99,28,92,8Mounting height for 5 lux below 3.2 metersLight distribution curvePhotometric data - 30m version, 200lm Escape route 2m wide 1 lux minMounting height [m]2,510,63,88,39,13,82,88,54,19,29,64,03,07,44,29,69,94,03,55,54,310,610,64,24,04,24,411,511,24,24,53,34,411,911,54,25,02,74,212,111,84,15,52,24,112,211,94,16,01,83,812,211,93,86,51,53,512,111,93,57,01,33,111,911,73,0Open (anti-panic) area 1 lux minMounting height [m]2,53,47,47,43,32,83,48,28,03,33,03,58,58,33,43,53,69,38,93,54,03,69,89,53,54,53,610,39,83,55,03,510,510,23,55,53,510,710,43,46,03,310,910,63,26,53,111,210,73,07,02,811,110,82,7Open (anti-panic) area 0.5 lux minMounting height [m]2,53,97,78,53,82,84,38,68,73,93,04,49,29,14,13,54,510,110,14,34,04,611,211,34,54,54,712,312,14,75,04,713,112,94,75,54,813,713,44,76,04,814,213,84,76,54,814,514,14,77,04,814,814,44,7Mounting height for 5 lux below 3.65 meters。

应急灯使用说明书

应急灯使用说明书一、用途本系列消防应急灯主要用于各类建筑物突发性停电而能自动发出应急照明的灯具，主要为楼梯口通道出口维尔西安地段提供应急照明。

二、产品特点本系列产品采用优质电子元件生产，具有亮度高、寿命长、耗能低等特点，灯内采用先进电路具有过充、过放、空载等多种异常状态保护。

三、应急灯图片：YJD-201 YJD-201A YJD-208YJD-208A YJD-221 YJD-221A其它应急照明产品：安全出口标志牌、强光手电、疏散指示灯三、应急灯技术参数：1）执行标准：GB17945-20002）电源：AC220V(±10%)/50Hz3）光源：6V 0.5A(3W*2)灯泡4）应急时间≥90分钟5）应急转换时间≤IS6）电池规格：3.6V1.8h 优质电池6V/1.8Ah6V/2.5Ah6V/4Ah四、使用说明1、本应急灯不易安装在户外及潮湿、有腐蚀性气体的地方。

2、应采用单独回路供电，不应与照明或其它带有开关电器共用回路，以保证应急灯能正常充电。

3、本产品设有工作状态指示灯，绿色显示主电，红色显示正在充电，黄色显示灯内系统出现故障，应定期检查产品工作状态是否正常。

4、当应急时间小于额定时间时请更换电池。

方法：断开电源将电池与线路板之间的连接线拔下，将新电池紧固在原来位置即可。

5、光源更换：当灯泡烧坏或变黑时，应换上通规格的灯泡。

方法：将灯头上的透明镜松开，将已坏灯泡扭下，换上新灯泡，再紧固灯泡即可。

6、线路中设有保险，交流为0.5A。

直流为2A，需要更换时请注意规格型号。

7、产品出厂时已放电。

使用时需充电18小时，即可达到额定应急时间。

8、产品长期储存和停用，应每三个月充放电一次，以保护电池的性能。

消防应急照明灯具安装说明书

一、安装声明：1. 安装前请仔细阅读说明书；2. 请专业电工安装；3. 为避免触电危险，在安装、维护前请确认关闭电源；4. 灯具可嵌入安装天花板表面，需预留足够的安装空间，不要在灯具上方覆盖隔热物和可燃物，以避免引发火灾；5. 玻璃如有开裂，请立即更换；6. 请勿将灯具安装于不稳定，不坚固的天窗上，以避免灯具坠落；7. 保留说明书，以备使用参考；8.此灯具内的光源应由制造商或其服务代理商或有类似资格的人来更换。

二、产品尺寸（单位：mm）：三、灯具安装(以HG-ZLZD-E10WDLF31为例，其余型号类似)：1. 将产品从包装箱中取出，安装前应检查灯具配件是否齐全；2. 确认天花板上有足够空间安装灯具(单位：mm) ，宽度方向需保证能放下电器盒；3. 在天花板上挖直径φ78mm的圆孔（不同灯具型号开孔尺寸不同，具体见产品尺寸）；4.将灯具的电源输入线接入对应供电系统，棕色接火线，蓝色接零线，黑色接开关线（与火线同相），黄绿色接地线；警告：如果灯具的外部软缆线损伤，需由专业人员更换，避免发生危险！5. 电器盒输入线接好电源线后，将电线，电器盒送入天花板，双手拇指、食指与中指把弹片向灯具的轴心方向按压，直至弹片进入天花板孔内；6.双手托住灯具送入天花板挖孔内，直至灯具面板与天花板表面贴平；7. 接通市电AC220V 时，灯具呈主电状态，然后点动试验按钮，检查试验灯具应急状态是否工作正常。

四、主要技术指标：1. 下照款2. 调角款五、性能及使用说明：灯具上有：红色（充电）、绿色（主电）、黄色（故障）三种颜色指示灯各一个（或红黄绿三色指示灯一个），试验按钮一个, 蜂鸣器（电器盒内）一个。

主电：绿色指示灯，此指示灯长亮时，表示市电正常（注：本灯具有电压自动转换电路，市电电压如果处在150V 左右时，灯具会由主电状态转入应急状态，当市电电压上升到170V 左右时，灯具会自动由应急状态恢复主电状态。

使用本灯具时，应检查输入交流电压是否正常）。

奥视威 FL-C60D 便携聚光灯使用说明书

技术参数>>注意事项>>清洁>>感谢您选择本公司产品，请在使用前通读本使用说明书，并妥善保存以备将来参考。

产品型号色温亮度最大照度半峰光束角CRITLCI工作电压输出功率整灯尺寸整灯净重FL-C60D2700K-8000K 0%-100%Spot: 25000Lux@1m Flood:4000Lux@1mSpot:15º ； Flood:60º9597DC 11-36V 约60W 如图所示约2.1kg1.请勿随意拆卸灯具或用金属物体接触灯具内部，以免造成损坏；2.请避免将灯具储存在满是灰尘或潮湿环境中，以免造成损坏；3.为避免运输过程中意外摔落损坏遮光片，请将灯头缩至最小位置收纳；4.环境温度低于-2℃使用本品，LCD风扇动画出现拖尾不影响使用；B接口为预留接口，请根据本公司相关产品的指定环境使用，不可用于其他用途，以免造成损失；6.仅限在-10℃～40℃的温度范围内使用本产品。

1.请使用柔软的干布清洁本产品菲涅尔透镜，亦可使用略微蘸有中性洗涤剂溶液的软布进行清洁，但在清洁后请用柔软的干布进行擦拭。

图1 图2使用方法 >>装箱清单 >>1. 安装根据使用需求，将本品安装在灯光脚架或支架上，通过灯体侧边可调手柄（图3 ⑧）调整灯具照射角度。

2. 供电方式选择本品支持通过扣板电池或电源适配器两种供电方式给灯具供电。

3. 亮度及色温设置及使用本品具备两种色温及亮度的调节模式：普通调节模式、快速调节模式。

按压亮度/色温调节旋钮（图3 ②/①）切换相应亮度或色温的调节模式，用户根据使用需求结合这两种调节模式可完成对亮度/色温的快速设置。

3.1 普通调节模式⑴.色温调节范围：2700K-8000K，调节步长：100K ⑵.亮度调节范围：0%-100%，调节步长：1%3.2 快速调节模式 ⑴.色温调节在该模式下，可快速选择常用色温：2700K，3200K，4500K，5600K，6500K,7200K,8000K ⑵.亮度调节范围：0%-100%，调节步长：10%4. 通信地址设置及使用4.1 通信地址的设置长按亮度调节旋钮（图3 ②）约2s即可进入通信地址的设置界面，通信地址设置范围：001-512。

消防应急照明灯安装使用说明书

消防应急照明灯安装使用说明书消防应急照明书安装使用说明书 1消防应急照明灯安装使用说明书一、概述本产品采用GB17945-2010标准，以LED为照明的应急灯，具有最新高科技产品，LED为发光，发光清晰，光色柔和，功耗极低，寿命长等特点，是当前一般灯管型应急照明的升级换代产品。

二、技术参数防护等级:?IP30 额定工作电压/频率:AC220V/50HZ 应急时间?90分钟应急输出光通量:?501m 应急转换时间:?1秒主电功率:2W电池种类:Ni-Cd镍镉电池保险丝规格:交流1A 直流5A 光源名称:发光二极管电池规格:Ni-Cd AA800mAh/2.4V光源输出参数:0.8W 三、安装方法:吊装、壁挂，吊装用吊链吊在拉手上，壁挂挂在灯箱后面的瓜子形孔上。

四、使用方法:1、接线方法:棕色线接火线，蓝色线接零线，黄绿色接地注:棕色线、蓝色线不能接任何开关。

2、把本产品插上交流220V电源(充电18小时)此灯具主电绿色指示灯亮起，LED正常发光，a( 用手按住试验开关2s进入试验状态，指示灯熄灭而LED仍然发光则表示应急工作正常;b( 按住试验开关4s绿色指示灯1HZ闪烁，进入月自检模拟状态，自检通过转入主电状态。

c( 按住试验开关6s绿色指示灯3HZ闪烁，进入年自检模拟状态，自检通过转入主电状态。

3、平时该消防应急灯具不点亮，应急才点亮;应急状态按住试验开关大于6s关断应急。

五、日常维护1、试验按钮用来模拟停电、月自检、年自检之用，以检测灯具应急工作是否正常，用户应按消防部分要求进行检测和维护。

1消防应急照明书安装使用说明书 22、灯具出厂内部电源于放空状态，使用前应先充电24小时，充电时充电灯亮起，接近充满红色指示灯熄灭，此时电路进入浮充对电池小电流充电。

3、声光报警1(故障灯黄灯1HZ闪烁，蜂鸣器1min/1次)，表示该灯充电回路短路或者开路;检查保险丝或电池，并及时修理。

4、声光报警2(故障灯黄灯3HZ闪烁，蜂鸣器1min/1次)，表示该灯光源短路，开路或应急回路断开;检查光源或应急回路，并及时修路。

LED便携应急灯规格说明书

TH-ZH3W恒流型应急电源应急灯规格书

HLL系LED爆炸防护灯具说明书

瑞丰LED光线灯具规格书说明书

Chloride Compac LED紧急灯具CLU介绍及参数说明书

应急灯说明书

消防应急照明灯安装使用说明书

消防应急灯具产品规格书

INL-03XLED灯应急电源规格书

HW-ZFJC-E3W-N650消防应急照明灯具说明书

Velos LED紧急出口灯系列说明书

EATON SafeLite 紧急灯具说明书

应急灯使用说明书

消防应急照明灯具安装说明书

奥视威 FL-C60D 便携聚光灯 使用说明书

消防应急照明灯安装使用说明书

奥视威 FL-C60D 便携聚光灯使用说明书