CylindricalLIFEPO4BatterySpecification圆柱型磷酸铁锂电池规格书
比克18650C4规格书
5 Technical characteristics 技术要求 5.1 Electronic performance 电性能
(fresh cells, tested at 22.5 ± 2.5℃, standard charge and discharge unless otherwise specified) （除非有特殊说明，否则所有测试要求为：温度为 22.5 ± 2.5℃，样本为新电芯，充放电制式为标准充电 和标准放电）
2100 mAh@0.2C
Nominal voltage 标称电压
3.7 V
Max Charging voltage 最大充电电压
4.2+0.05 V
Discharge ending voltage 放电终止电压
3.0 ±0.05 V
Max charge current 最大充电电流
Max discharge current 最大放电电流
capacity capacity
at at
1.0C 0.2C
≥
90%
;
1.0C放电容量 0.2C放电容量
≥
90%
能
discharge discharge
capacity capacity
at at
2.0C 0.2C
≥
80% ;
2.0C放电容量 0.2C放电容量
≥
80%
;
Cycle life 5.1.2 循环寿命
Maximum allowable charge and discharge ambient temperature. Charging and discharging at these conditions will shorten cell cycle
IFR14500-磷酸铁锂-600mAh
Product SpecificationFILE NAME： SPECIFICATIONS OFSEALED LiFePO 4 CYLINDRICAL BATTERIESMODEL： IFR14500MAB 600mAhSpecification No.: S/RONDA 0181-1EDITION： A3DATE： 2014-1-14EDITIONAMENDMENTDATE OF ISSUE AA0 Initial publishA1 1.Editing the parameters of IR and the weight2.Editing the parameters of the diameter and the heightA2 Editing the parameters of charge and discharge temperature A3 Editing the parameter of IR2008-11-05 2012-07-182013-11-112014-1-14DrawnCheckedReviewedApprovedNotice: If the document wasn’t signed and stamped, the information (subject to change without prior notice) contained in this document is for reference only and should not be used as a criterion for product guarantee or warranty.Product SpecificationIFR14500MAB 600mAh 1. SCOPEThe specification governs the performance of the following RONDA LiFePO4 Cylindrical cell and its battery pack. (Refer to the attached figure 1 )Rated capacity: 600mAhDesignation: IFR14500 (D: 13.90±0.2mm H: 48.50±0.5mm)Figure 1- Jacketed LiFePO4 cylindrical cells2. DATA OF BATTERY PACKThe data of battery pack, including voltage and weight, is almost equivalent to the multiple numbers of the relevant single cells.Example: Battery pack consisting three single cellsNominal voltage of single cell = 3.2VNominal voltage of battery pack = 3.2V×3 = 9.6V3. RATINGSTable 1 - Ratings of the cellsDescription Unit Specification Remark Nominal Voltage V 3.2 Single cellMax. Charge Voltage V 3.7 Single cellDischarge cut-off Voltage V 2.0 Single cellMax. constant charge current mA 600(1.0ItA) /Max. constant discharge current mA 1200(2.0ItA) /Rated Capacity mAh 600Charge with 0.2ItA to3.7V,then charge withconstant voltage till thecharge current is less than0.01ItA，and rest for 60 min,discharge with constantcurrent 0.2ItA to 2.0V.Operation Temp. ℃Charge:0~+40Discharge:-10~+40/Storage Temp. ℃ -10~+45 /within one monthWeightgAbout 18.0 For reference onlyStorage Voltage V3.20~3.40Product SpecificationIFR14500MAB 600mAh4. PERFORMANCE AND TEST METHODStandard charge method: Charge with constant current 0.2ItA to 3.7V/cell,and then charge withconstant voltage 3.7V,when the charge current is less than 0.01ItA,stop charging. Standard testing condition：Temp. 20±5℃Relative Humidity 65±20%RH (Unless otherwise stated)Table 2 – Performance and test methods bTest Item Unit SpecificationTest ConditionsRemarksDischarge performance 20 ah≥5After Standard Charge, stored for 1-2 hrs, then Discharge with 0.2ItA to 2.0V（25±2℃） Can be recycled for 5 times -10 h ≥3After Standard Charge, stored for 2h in -10±2℃, then discharged with 0.2I t A to 2.0V./55 h ≥4.5 After Standard Charge, stored for 2h in 55±2℃, then discharged by 0.2I t A to 2.0V./Charge (capacity)retention h/mi n≥4h15min After Standard Charge, stored on open circuit for a period of 28days in 20±5℃, then discharged with 0.2I t A to 2.0V./Endurance in cycles cycle ≥1000 Discharge with 0.2ItA to 2.0V, charge with 0.2ItA to 3.7V,then charge with 3.7V till the charge current less than 0.01ItA,stored for 10min,and move to next cycle, cycles should be repeated until the discharge capacity is less than 80% of normal capacity for three times. 20±2℃Internal resistance mΩ ≤55 50% Charged ,to measure in AC 1000Hz (20±2)℃/4.2 Safety performanceTest ItemSpecification Test conditionOvercharge testNo fire,No explosionDischarge with 0.2ItA to 2.0V, charge with 3ItA to5.0V,when the constant voltage get to 5.0V thecurrent is close to 0, last for 30min.Over-discharge testNo fire,No explosionAfter Standard charge, then discharge with 0.2ItAto 2.0V/cell, and then keeps on discharging for24h loaded with 30 Ω.S/RONDA 0181-1Heat Impact testNo fire,No explosionStandard charge first, then put the battery in the hot chamber, the temp. of chamber increased by 5±2℃ every min. till 130±2℃ keep for 10min.Product SpecificationIFR14500MAB 600mAh4.3.Reliability PerformanceTest Item SpecificationTest conditionHigh Temp. testElectric performance and appearance are free from affected Put the full charged battery in 70℃ for 2 hoursLow temp. testElectricperformanceandappearance are free fromaffectedPut the full charged battery in -10℃ for 2 hours，then stored in room temp. for 3 hours High Temp&High HumiditytestElectric performance and appearance are free from affected,including package.Put the full charged battery in the chamber of 40±2℃ 90-95%RH for 48 hours, then stored in 20±5℃ for 2 hours5. CONFIGURATION, DIMENSIONS AND MARKINGSPlease refer to the attached drawing. 6. EXTERNAL APPEARANCEThe cell/battery shall be free from cracks, scars, breakage, rust, discoloration, leakage nor deformation.6. Protection function requirementThe cell/battery shall be free from cracks, scars, breakage, rust, discoloration, leakage nor deformation.7. Protect requirement of batteryWhen Li-ion rechargeable battery is working under voltage/current which is higher than the specification stipulated, the electrolyte may be decomposed, which will affect the safety performance of the battery; the battery performance will be worsen if its voltage lower than 1.0V. In order to avoid overcharging, over-discharging or over-current ，please use right charger to charge the battery.To make sure safety, the charger and protect circuit should comply with following requirement:Object ItemRequirement RemarksCharger Charge cut-off Voltage (3.700~4.200)±0.049V / Protect Circuit （For reference only） Overcharge protect Voltage (3.700~4.200)±0.025V / Overcharge recover Voltage (3.700~4.200)±0.050V/ Discharge cut-off Voltage2.0±0.10V/S/RONDA 0181-1Over-discharge protect Voltage 2.0±0.08V/Over-discharge recover Voltage 2.0±0.10V /Over-current protect Value 2.0±0.2A / Note The above parameter is for reference only, customers could decide to adopt or change according to the practical situation.Product SpecificationIFR14500MAB 600mAh 8. Period of warranty12 months from manufacture date9. Disclaimer clauseFire or explosion will happen in case misuse of battery. So please comply with Ronda specification and caution in the document. Ronda will take no responsibility for any accident when the cell is used under other conditions than those described in this Document.10. Caution in use1）Do not immerse the cell in water, it should be kept in dry;2）Do not use/expose the cell to extreme heat or flame;3）Use the special Li-ion charger to charge the cell;4）Do not reverse the polarity of the cell for any reason;5）Do not connect cell to the plug socket or car-cigarette-plug;6）Do not throw the cell into heater or fire;7）Do not connect the cell with metal directly;8）Do not handle or store with metallic like necklaces, coins or hairpins, etc.9）Do not strike the cell by hammer or tread it.10）Do not make the direct soldering onto a cell or drive a nail into the cell;11）Do not use or leave the cell in high temp.(under the blazing sun or in heated car by sunshine),to avoid fire, disabled or life shorter of the cell;12）Do not use the cell under strong static or magnetic field, to avoid destroying of the protect device;13）If the electrolyte came into the eyes, do not rub, you should wash with water and contact a doctor at once;S/RONDA0181-114）If find any peculiar smell, heat, color change, distortion of the cell or there is any abnormity in using, storing or charging process, you should take it from the device or charger and stop its use;15）To avoid bad contact or function disabled, please use a dry cloth to clean the battery if it is dirty;16）Wasted cells should be packed with a insulated paper, to avoid fire or explosion.Product SpecificationIFR14500MAB 600mAh Base Data:Nominal voltage 3.2VCapacity comparison(mAh)0.2I t A 1.0I t A600 570Weight(g) 18.0Internal Impedance at 1000Hz(After Charge;m )≤55Charge currentStandard 120mAFast 600mACharge timeStandard /Fast /D 13.90±0.2mmAmbient Temperature charge Standard 0~+40℃H 48.50±0.5mm Fast +10~+40℃Discharge -10~+40℃Storage -10~+45℃S/RONDA0181-1this document is for reference only and should not be used as a criterion for product guarantee or warranty.产品规格书文件名称 圆柱型磷酸铁锂电池规格书 型 号 IFR14500MAB 600mAh 编 号 S/RONDA0181-1 版 次 A3日 期2014年1月14日版 次 修 改 内 容生 效 日 期 AA0 初版发行A1 1.修订电池内阻参数和重量 2.修订电池外径参数和高度 A2 修订充电和放电温度 A3 修订电池内阻参数2008-11-05 2012-07-182013-11-11 2014-1-14S/RONDA 0181-2草 拟审 核复 核批准如果文件没有签名并盖章，本文件中包含的信息仅供参考，不应被用来作为产品提供保证或担保的基准。
梅德隆 12V 100Ah 磷酸铁锂电池组 使用说明书
Mainland Energy Conversion Ltd.电话: +852 2366 9610使用说明书LiFePO4 磷酸铁锂电池组12V/100Ah 系列:• 由于身体，感官或精神方面的能力不足或是因经验不足而无法安全使用本电池组的人，不得在没有技术人员的控制或指导的情况下使用。
• 本电池组不适合儿童使用，有机会危及生命。
并须时刻提防触电的危险。
• 时刻远离易燃气体、溶剂或蒸汽。
时刻确保空气流通，避免明火或火花，切勿焚烧电池组，以免引起爆炸事故！ • 请严格遵守充放电指示，并仅使用具合适规格或充电模式之充电器进行充电。
• 请确保正负极端子上的螺丝时刻锁紧，并仅使用具电绝缘功能的螺丝刀。
• 使用前请确保正负极做好电气绝缘。
• 切勿打开或拆开电池组。
维修工作只能由获授权的专业技术人员操作。
• 拆装电池组可能会导致电芯间的短路，从而引致火花、有害气体泄露、电解液体泄露，甚至爆炸。
• 如发生明显的损坏或故障，例如：变形的外壳、电解液泄漏或出现任何奇怪气味，请停止使用电池组。
请立即断开设备的电源和负载。
• 请勿接触有害的电解液。
如电解液不慎接触到眼睛或皮肤，请立即以大量清水清洗眼睛或皮肤，并咨询医生意见。
• 避免太阳直接照射电池组或存放于超过40°C 的温度。
•电池组应贮存在干燥地方（相对湿度<80%），仅使用干布清洁电池组。
避免电池组与任何液体接触。
• 被动散热• 經电镀及喷粉处理的铁制外箱• 在放电深度达 80% 状态下，>2000 次循环 • 过充、过放自动保护机制 • 在高低温环境下自动关闭 • 先进的蓝牙APP 显示电池状态•LED 指示灯显示电池容量和错误的警告1.充电端子 / 放电端子2.LED 指示灯 (LED 4 to LED 0)IP65电池组配备智能电池管理系统 (BMS)，以确保稳定和高效率的充电及放电表现。
电池组可使用专用的锂电池充电器充电。
AA 螺帽电池电源 Polymer LiFePO4 立方体电池说明书
AA Portable Power Corp , Email:**********************Page 1 / 7PolymerLiFePO4 Lithium-ion BatteryProduct SpecificationModel ：87122200L1. This product specification describes polymer lithium-ion battery. Please using the test methods thatrecommend in this specification. If you have any opinions or advices about the test items and methods, please contact us. Please read the cautions recommended in the specifications first, take the credibility measure of the cell’s using.If the cells should be using at the environment that not preferred in this document, please connect with our first and get our authorization. For the reason of stable Performance and better safety, battery pack with more than 2 cells connected in serial way should be charged with a balance charger.It is claimed that we should have no any responsibility with the contingency and loss due to the cells’ wrong usage (not preferred in the product specification). 2. Product Type, Model and Dimension ： 2.1 Type: Polymer lithium-ion battery2.2 Model ：87122200L (Cell adding Cu Tabs)2.3 Dimension( Max. T*W*L)mm ：8.7×123.0×201.5 3. Specification ：Item Parameter RemarkNominal Capacity 15000mAh ±5%0.2C 5A discharge ，25℃Nominal V oltage 3.2V Average V oltage at 0.2C 5A dischargeStandard Charge Current 0.2C 5A Working temperature ：0～45℃ Max Charge Current 1.0C 5A Working temperature ：0～45℃Charge cut-off V oltage 3.80±0.05V CC/CVDischarge Current Cont.0.2C 5A~Max:2.0C 5AWorking temperature ： 0~60℃Discharge cut-off V oltage2.4VCell V oltage 3.2～3.4V When leave factory Impedance ≤4m Ω AC 1KHz after 50% charge,25℃WeightApprox:382gStorage Temperature≤1month -10～45℃Best 20±5℃ for long-time storage ≤3month0～30℃≤12month 0～30℃Storage humidity 65±20% RH4. General Performance：Definition of Standard charging method：At 20±5℃，charging the cell initially with constant current 0.2C5A till voltage 3.8V, then with constant voltage3.8 V till current declines to 0.05C5A.Item Test Methods Performance4.1 0.2C CapacityAfter standard charging, laying the battery 0.5h, then dischargingat 0.2C5A to voltage2.4V, recording the discharging time. ≥300min4.2 1.0C Capacity After standard charging, laying the battery 0.5h, then dischargingat 1C5A to voltage 2.4V, recording the discharging time.≥54min4.3 Cycle lifeConstant current 1C5A charge to 3.8V, then constant voltagecharge to current declines to 0.05C5A, stay 5min，constant current1C5A discharge to 2.4V，stay 5min. Repeat above steps till continuously discharging time less than 36min.≥1000次4.4 Capability ofkeepingelectricity20±5℃,After standard charging, laying the battery 28days,discharging at 0.2C5A to voltage2.4V, recording the dischargingtime.≥240min5.Environment Performance：Item Test Methods Performance5.1HightemperatureAfter standard charging, laying the battery 4h at 55℃±2℃, then discharging at 0.2C5A to voltage 2.4V, recording thedischarging time.≥270min5.2LowtemperatureAfter standard charging, laying the battery 4h at -10℃, thendischarging at 0.2C5A to voltage 2.0V, recording thedischarging time.≥180min5.3Constanthumidity andtemperatureAfter standard charging, laying the battery 48h at 40±2℃,RH 93±2%. Recording 0.2C5A discharging time≥270min。
14430(700mAh)中英文
保定风帆新能源有限公司Baoding Fengfan New Energy Co.,Ltd.高能量圆柱型电池High Capacity Cylindrical Li-ion BatteryBFN14430-700mAh编制compile审核audit批准authoriz e2007-06-23发布Issue2007-06-23实施Execute地址：中国河北省保定市高开区鲁岗路Add:No.199Lugang Road of High Technology Z one,Baoding City,Hebei Provice,China 电话Tel：+863123327785传真Fax：+8631233277851.适用范围Scope of Application本规格书规定了保定风帆新能源有限公司向客户提供的BFN14430(700mAh)圆柱型锂离子电池的技术参数及测试标准。
本型号电池适用于摄像机、数码照相机、玩具、无绳电话、仪器仪表等电子产品。
This specification gives the technical parameters and testing standard of BFN14430(700mAh) provided by Baoding Fengfan New Energy Co.,Ltd..This kind of battery is suitable for electric products,such as digital cameras,vidicons,toys,cordless telephones,instruments and meters, etc.2.种类型号Kind&Type2.1种类Kind：圆柱型锂离子二次电池Rechargeable Cylindrical Lithium-ion Battery2.2型号Type：BFN14430-700mAh3.参考标准Reference Standa rds此规范参考GB/T18287-2000、UL1642及IEC61960—1：2000等技术标准规范编制。
维克顿能源 LiFePO4 锂磷电池安全数据表说明书
Victron Energy Batterie SICHERHEITSDATENBLATTLithium SuperPack 12,8V/20Ah, 60Ah, 100Ah, 200Ah, 25,6V/50AhABSCHNITT 2 - ZUSAMMENSETZUNG/INFORMATIONEN ZU DEN INHALTSSTOFFENInhaltsstoff G ewicht % CAS-Nr. EC-Nr. Phosphat 26 % -- PVDF 1,5 % 24937-79-9 -Graphit 13 % 7782-42-5 231-955-3 CMC 0,2 % 07.11.9000 -Al 6% 7429-90-5 231-072-3 Cu10 % 7440-50-8 231-159-6 PP-Separator 2,1 % -- Stahl 20 % - - Elektrolyt16 % - - Schrumpffolie PVC 0,03 % - - PP Dichtungsring0,05 %--GEBRÄUCHLICHE BEZEICHNUNG: (auf dem Etikett verwendet) Lithium-Ionen-BatterieABSCHNITT 6 - MASSNAHMEN BEI UNBEABSICHTIGTER FREISETZUNGWasser durchnässen oder mit reichlich Wasser besprühen. Nachdem sie abgekühlt ist, in einen genehmigten Behälter geben und in Einklang mit den örtlichen Bestimmungen entsorgen.Persönliche Sicherheitsmaßnahmen: Säureresistente Schürzen, Stiefel und Schutzkleidung. Durch die ANSI genehmigte Schutzbrillen mit Seiten-/Gesichtsschutz empfohlen.ABSCHNITT 11 - TOXIKOLOGISCHE ANGABENWiederaufladbare Lithium-Batterien enthalten keine giftigen Materialien.ABSCHNITT 12 - TOXIKOLOGISCHE ANGABENBei normaler Nutzung bis zum Ende der Lebenszeit kann die Batterie recycelt werden und verursacht keinerlei Umweltverschmutzung. ABSCHNITT 13 - ENTSORGUNG1. In Einklang mit den geltenden Bestimmungen entsorgen. Diese können je nach Land unterschiedlich sein.2. Die Anschlüsse von Lithium-Ionen-Batterien sollten vor der Entsorgung isoliert werden und am besten sollten die Batterien einzeln inPlastiktüten verpackt werden.3. Batterien dürfen nur von autorisierten Entsorgungsstellen im Feuer entsorgt werden.ABSCHNITT 14 - TRANSPORT1. UN-NO.3480ARD /RIDKlasse 9 Verpackungsgruppe II ADR/RID-EtikettenKorrekte Versandbezeichnung Lithium-Ionen-Batterien, UN3480IMOKlasse 9 Verpackungsgruppe II IMO-EtikettenKorrekte Versandbezeichnung Lithium-Ionen-Batterien, UN3480IATA-DGRKlasse 9 Verpackungsgruppe II ICAO-EtikettenKorrekte Versandbezeichnung Lithium-Ionen-Batterien, UN34802. Victron Energy B.V. erklärt hiermit, dass das …UN Manual of Tests and Criteria“, Teil III, Untersektion 38.3 eingehalten wurde.3. In der Luftfracht werden kleine Lithium-Ionen-Batterien (Zellen<20 WH oder Packs>100 WH) als “Expected Lithium-ion Batteries” angesehen, wenn sie den Anforderungen der Ed. 63 der IATA Bestimmungen (UN3480) und ICAO Verpackungsanleitung 965 Abschnitt II entsprechen. Diese legen weniger als 10 kg Gesamtgewicht pro Paket fest. So gekennzeichnetes Versandgut kann als normale Fracht unter dem aktuellen IATA versandt werden.4. In anderen Fällen (insbesondere bei großen Zellen >20 WH oder Packs > 100 WH), gelten diese als Klasse 9 (Siehe Verpackungshinweis 965 Abschnitt I für Luftfracht).5. In der Seefracht gelten Lithium-Ionen-Batterien als "Lithium-ion-Batteries-Not Restricted", sofern sie den Anforderungen des IMDGfür IMO Gefahrgut-Regulierung (UN3480) entsprechen.6. Der Transport von wiederaufladbaren Lithium-Ionen-Batterien wird durch mehrere Stellen reguliert, beachten Sie: IATA, IMO, ADR/RID. ABSCHNITT 15 - BESTIMMUNGEN1. TemperaturbereichFortlaufend SofortLagerung Entladung Aufladen +25°C ±5°C30/80°C0/75°C-45/+85°C-45/+85°C-0/+75°C2. Spezifische Energie: (Hinweis: Wh = normale Spannung x Nenn-Ah) kg = Durchnittliches Gewicht der Batterie)3. Spezifische Pulsleistung: 600 w-1200 w/kg schwankt je nach Größe4. Mechanische Widerstandsfähigkeit: Wie in der IEC-Norm festgelegt.ABSCHNITT 16 - SONSTIGE INFORMATIONEN1. Diese Angaben wurden aus Quellen zusammengetragen, die als zuverlässig erachtet werden und dies geschah nach bestem Wissen und Gewissen und so genau und zuverlässig wie es zu dem Zeitpunkt der Erstellung möglich war. Jedoch wird keine Erklärung, Gewährleistung (weder ausdrücklich noch impliziert) noch eine Garantie bezüglich der Genauigkeit, Zuverlässigkeit oder Vollständigkeit der hier gemachten Angaben abgegeben.2. Diese Angaben beziehen sich auf die spezifisch aufgeführten Materialien und gelten möglicherweise nicht für solche Materialien, die in Kombination mit anderen Materialien oder in irgendeinem Verfahren verwendet werden. Es obliegt der Verantwortung des Nutzers selbst, sich ausreichend bezüglich der Eignung und Vollständigkeit dieser Angaben für seine jeweilige Nutzung abzusichern.3.Victron Energy B.V. übernimmt keinerlei Haftung für Verluste oder Schäden, die entweder direkt der indirekt, nebensächlich oder als Konsequenz aus der Nutzung dieser Angaben entstehen. Victron Energy B.V. bietet keine Gewährleistung gegenüber Patentverletzungen. Weitere Informationen sind telefonisch unter Angabe des beabsichtigten Zweckes möglich.。
RS PRO 14500 3.7V 800mAh Li-ion 循环电池说明书
ENGLIS.Li-ion Cylindrical BatterySpecificationLi -i o n 14500 3.7V 800m A h50.5-1.01 .ScopeThis specification describes the basic performance, technical requirement, testing method, warning and caution of the Li- ion Cylindrical rechargeable battery .The specification only applies to RS PRO Ltd.2. Products assembly drawing and size refers to picture 13.SpecificationNO.ItemSpecifications3.1Typical Capacity 820mAh @ 0.2C Discharge Minimum capacity 800mAh @ 0.2C Discharge 3.2Nominal voltage3.7V3.3Standard ChargeCC/CV,0.2C5A, 4.20V3.4Standard Discharge CC,0.2C5A, 3.00V3.5End-of-charge Voltage4.20V±0.05V3.6End-of-charge Current 0.02C5A （At CV mode）3.7End-of-discharge Voltage 3.00 V3.8Charging Time 8.0hours（standard charge）3.9Quick Charge Current 800mA （1.0C 5rate）3.10Quick Discharge Current 1600mA （2.0C 5rate）3.11Max Discharge Current 2400mA （3.0C 5rate）3.12Initial Impedance Max:70m3.13 Weight Approx(约)：20.2±2g3.14Operating temperature Charging ： 0℃~45℃Discharging ：-20℃~60℃3.15Storage temperature -5℃~35℃3.16Storage Humidity ≤75% RH3.17Appearance Without scratch, distortion, contaminationand leakage3.18Standard environmental conditionTemperature ： 25±2℃Humidity : 45-75%RHAtmospheric Pressure ： 86-106 KPA3.19Temperature Dependence of Discharge Capacity @ 0.2C DischargeChargetemperatureDischarge temperature25℃-10℃0℃15℃25℃40℃Relative Capacity50%80%90%100%100% 4 General PerformanceNo.Item Test Methods and Condition Criteria4.10.2CCapacityAfter standard charging, rest battery for 10min,then discharging at 0.2C to voltage 3.0V,recording the discharging time.≥300min4.2Cycle Life Constant current 0.5C charge to 4.2V, thenconstant voltage charge to current declines to0.01C, rest 10min，constant current 0.5Cdischarge to 3.0V，rest 10min. Repeat abovesteps till continuously discharging capacity≥300 times(次)Higher than 80% of the Initial Capacities of the Cells4.3Capability ofkeepingelectricity20±5℃, After standard charging, rest thebattery 28days, discharging at 0.2C to voltage3.0V, recording the discharging time.≥240min5 Environment PerformanceNo.Item Test Methods and Condition Criteria5.1Discharge athightemperatureAfter standard charging, rest the cells 4h at60±2℃, then discharging at 1C to voltage 3.0V,recording the discharging time.≥54min5.2Discharge atlowtemperatureAfter standard charging, rest the cells for 16h at-20±2℃, then discharging at 0.2C to voltage 3.0V,recording the discharging time.≥210min5.3ThermalshockPut the cells in the oven. The temperature of theoven is to be raised at 5±2℃ per minute to atemperature of 130±2℃ and remains 30 minutes.No fire, nosmoke6 Safe CharacteristicNo.Item Test Methods and Condition Criteria6.1Over chargetestingAt 23±5℃, charging cells with constantcurrent 2C to voltage 5.0V, Stop test till cellstemperature 10℃ lower than max temperature.No smoke or fire6.2OverdischargetestingAt 23±5℃, According to the requirements ofstandard charge, the cells will be discharge tocut-off voltage, then connect with external loadof 30 ohm for 24 hours.No fire, nosmoke, noleakage.6.3Short-circuittestingAt 23±5℃, After standard charging,connect cells anode and cathode by wire whichimpedance less than 80±20mΩ, keep 6h.No smoke or fireAbove testing of safe characteristic must be with protective equipment.※7. CAUTIONS IN USETo ensure proper use of the battery please read the manual carefully before using it. Handling(1)Do not expose to, dispose of the battery in fire.(2)Do not put the battery in a charger or equipment with wrong terminals connected.(3)Avoid shorting the battery(4)Avoid excessive physical shock or vibration.(5)Do not disassemble or deform the battery.(6)Do not immerse in water.(7)Do not use the battery mixed with other different make, type, or model batteries.(8)Keep out of the reach of children.(9)Do not place in a pocket.charge and dischargeBattery must be charged in appropriate charger only.Never use a modified or damaged charger.Do not leave battery in charger over 24 hours.Store the battery in a cool, dry and well-ventilated area.Regulations vary for different countries. Dispose of in accordance with local regulations.8. Battery operation instruction8.1 ChargingCharging current：Cannot surpass the biggest charging current which in this specification book stipulated。
LiFePO4 Battery - BatterySpacecom
2
3
4
5
6
7
8
≤50mΩ
9
Approx:0.37kg 70×47×101
10
大致数据 Approx
2-2 主要性能 Genபைடு நூலகம்ral Performance
标准充电方式 Standard charge: 电池组必须用专用充电器进行充电，在 23±2℃环境下 0.2 C20A 恒流恒压方式充电到 7.6V。 Charge battery pack with specific charger, 0.2 C20A constant Current/constant voltage to 7.6V at 23±2℃. 项目 Item 测试方法 Test Methods 标准充电后，静置 0.5 小时，然后以 20h 率电流放电到 4.8V 的放电时间。 After standard charging, laying the battery 0.5h, then discharging at 0.05C20A to voltage 4.8V,recording the discharging time. 标准充电后，静置 0.5 小时，然后以 1 C20A 放电到 4.8V 的 放电时间。 After standard charging, laying the battery 0.5h, then discharging at 1C20A to voltage 4.8V, recording the discharging time. 标准充电后， 在－10℃环境中静置 4 小时以上， 然后以 0.05C 放电到 4.0V 的放电时间。 After standard charging, laying the battery in -10 ℃ more than 4h, then discharging at 0.05C20A to voltage 4.0V recording the discharging time. 指标 Performance
RS Pro主动LiFeS2电池AAA型号规格说明说明书
ENGLISScopeThis specification is suitable for the performance for the Lithium and Iron Disulfide battery.ModelRS-AAA/IEC R3 (Li/FeS2)Reference DocumentQ/(GZ) PH001-2004: Lithium and iron disulfide batteryIEC60086-4: 2000 Primary batteries- Part 4 Safety of lithium batteriesNo.ItemsNominal VoltageRated CapacityWorking VoltageMax. Discharge CurrentDischarge Cut-off VoltageVolumeWeightLithium Content6. Test Conditions and Performance6.1Measuring Instrument or Apparatus6.1.1 Dimension Measuring InstrumentThe dimension measurement shall be implemented by calipers with equal or more precision scale of 0.01mm6.1.2 VoltmeterStandard class specified in the national standard or more sensitive class having inner impedance more than 10KΩΝ6.1.3 AmmeterStandard class specified in the national standard or more sensitive class. Total external resistance including ammeter and wire is less than 0.01Ω.6.2 Standard Test ConditionsUnless other defined, test and measurement shall be done under temperature of 20±5℃ and relative humidity of 45~85%. If it is judged that the test results are not affected by such conditions, the tests may be conducted at temperature 10~30℃ and humidity 25~85％RH. 6.3 Visual inspectionThere shall be no such defect as scratch, flaw crack, and leakage, which may adversely affect commercial value of cell.6.4 Basic CharacteristicsNo.Item Measuring Procedure Criteria1Open-Circuit Voltage The open-circuit voltage shall bemeasured by voltmeter.≦1.74V2Dimension Use calipers test cell’sdimensions.As item 4.93Discharge capacity The capacity means thedischarge capacity of the cell,which is measured bycontinuously discharging with acurrent of 100mA to 0.8V(25±2℃)≦1050 mAh4External short circuit Positive and negative of freshbattery are connected by a Cuwire, this short-circuit condition iscontinued for 1 day at roomtemperature (20±2℃)No leakage; No explosion5Forced discharge Discharged to 0.8V at 30mA; Andthen the sample cell is forceddischarged with 30mA for 3hours.No explosion ; No fire 6.5 Mechanical CharacteristicsNo.Item Test Method Criteria1Impact A15.8mm diameter bar isvertically placed across the centreof the sample cell. A9.1 kg massis dropped from a height of 61cmonto the sampleNo explosion, No fire2Vibration Freq: 10~55hz; Amp: 2mm; Threedirections; total 90 min No leakage, No explosion, no fire 0.02V total maximum OV changes3Crush A samples cell is to be crushedbetween two flat surfaces.Force: 32mm diameter piston;Max pressure: 17.2MPa; Maxforce: 13KN; Released when themax pressure obtained.No explosion, No fire6.6 Environmental testNo.Item Test Conditions Criteria1Thermal test Fresh batteries, store at 70degree C for 4 hours; 20 degreeC for 4 hours; -20 degree C for 2hours. 20 degree C for 2 hours.All cycled 5 times No leakageNo explosion; No fire2Heating test Fresh battery is heated in anoven. The rate of temperatureraised: 5±2℃ per minute; Maxtemperature 150±2℃ remainingfor 10 minutesNo explosion; No fire3Drop test Fresh batteries; Height: 1m, 6times: Each direction two times;Concrete floor No leakageNo explosion; No fireMajor ApplicationsLithium batteries deliver long-lasting power to keep up with today’s high-tech, Power hungry devices like digital cameras , MP3, MP4 Flashlight, Electric Torch , CD, MD, Toy hand-held games etc. Which could replace for Alkaline battery and other ordinary 1.5V primary battery.7. Cautions in useTo ensure proper use of the battery please read the manual carefully before using it.HandlingDo not expose to, dispose of the battery in fire.Do not place in a pocket.Do not put the battery in a charger or equipment with wrong terminals connected.Avoid shorting the batteryAvoid excessive physical shock or vibration.Do not disassemble or deform the battery.Do not immerse in water.Do not use the battery mixed with used or other different make, type model batteries.Keep out of the reach of children.StorageStore the battery in a cool, dry and well-ventilated area.Disposal Regulations Vary for different countries.Dispose of in accordance with local regulations.8. Battery operation instruction8.1 Discharging currentThe discharging current does not have to surpass this specification book stipulation the biggest discharging current, the over sized electric current electric discharge can cause the battery capacity play to reduce and to cause the battery heat.8.2 Electric discharge temperatureThe battery discharge must carry on in the ambient temperature scope which this specification book stipulated.8.3 Storing the BatteriesThe battery should store in the product specification book stipulation temperature range. If has surpasses above for six months the long time storage, the discharge capacity will decrees sharply9. Other Chemical ReactionBecause batteries utilize a chemical reaction, battery performance will deteriorate over time even if stored for a long period of time without being used. In addition, if the various usage conditions such as discharge, ambient temperature, are not maintained within the specified ranges the life expectancy of the battery may be shortened or the device in which the battery is used may be damaged by electrolyte leakage. Pease change the battery in time.10. NoteAny other items which are not covered in thus specification shall be agreed by both parties.。
LBC-38D P LiFePO4 电池充电器说明书
Meaning of Markings
For safety, please pay special attention to the items indicated by the following marks.
%"/(&3
Procedures which may have a high risk of death/serious injury to the user if not carried out properly.
8"3/*/(
Do not touch the battery charger and the battery for long hours while charging. Extended contact with them could result in minor burns.
If the battery charger or the battery is damaged when it falls to the ground or the floor, do not use it. To avoid electric shock or injury, never touch any internal parts of it which may be exposed.
通信用磷酸铁锂电池标准
目次前言 (1)1 适用范围 (1)1.1 适用范围 (1)2 规范性引用文件 (1)3 术语和定义 (1)3.1 磷酸铁锂电池 LiFePO4 battery cell (1)3.2 单体电池 Single battery (1)3.3 磷酸铁锂电池模块 LiFePO4 battery block (2)3.4 电池采集模块 battery acquisition module(BAM) (2)3.5 电池管理模块 battery management module（BMM） (2)3.6 磷酸铁锂电池组 LiFePO4 battery system (2)3.7 标称容量nominal capacity (2)3.8 标称电压nominal voltage (2)3.9 终止电压 end of discharge voltage (2)3.10 循环寿命 cycle life (2)3.11 容量保存率 save rate of capacity (2)3.12 内阻 internal resistance (2)3.13 电导 conductance (2)4 产品分类和系列 (3)4.1 电池模块额定容量系列（Ah） (3)4.2 电池组输出电压标称值系列 (3)4.3 电池组应用系列 (3)4.4 电池组管理系列 (3)5 要求 (3)5.1 使用环境条件 (3)5.2 外观 (3)5.3 性能指标 (3)5.4 电池间连接电压降 (6)5.5 寿命 (6)5.6 安全性能 (6)5.7 储存 (7)5.8 电磁兼容性 (7)5.9 BMM要求 (8)5.10 监控要求 (10)6 检验方法 (10)6.1 检验条件 (10)6.2 检验仪表要求 (10)6.3 外观 (10)6.4 放电性能 (10)I / 16.5 电池组性能一致性 (11)6.6 容量保存率 (11)6.7 电池间连接电压降 (11)6.8 寿命 (11)6.9 安全性能 (12)6.10 储存 (13)6.11 电磁兼容性 (13)6.12 BMM测试方法 (14)6.13 监控要求 (15)6.14 电池管理模块环境试验 (16)7 应用方法与要求 (16)7.1 应用分类 (16)7.2 BMM与开关电源系统的关系 (17)7.3 工作方式 (17)8 检验规则 (17)8.1 检验分类 (17)8.2 出厂检验 (17)8.3 鉴定检验（型式检验） (19)9 标志、包装、运输、储存 (19)9.1 标志 (19)9.2 包装 (19)9.3 运输 (19)9.4 储存 (19)附录 A (20)附录 B (21)前言本规范的目的是为加强中国移动使用的通信用磷酸铁锂电池的管理，使新建、改建、扩建工程中通信用磷酸铁锂电池的设计及设备选型有标准可依。
铁锂电池技术协议
铁锂电池技术协议引言本文档旨在明确铁锂电池技术的相关规范和要求，以确保铁锂电池的安全性和可靠性。
铁锂电池作为一种新型的绿色储能技术，具有高能量密度、长寿命、环保等优势，被广泛应用于电动汽车、储能系统等领域。
制定本技术协议是为了规范铁锂电池的生产、使用和维护，促进铁锂电池技术的不断发展和应用。
1. 术语定义•铁锂电池（LiFePO4 Battery）：指采用铁锂磷酸盐（LiFePO4）作为正极材料的锂离子电池。
•充电量（Charge Capacity）：指铁锂电池在充电过程中所吸收的电荷量，单位为安时（Ah）。
•放电量（Discharge Capacity）：指铁锂电池在放电过程中所释放的电荷量，单位为安时（Ah）。
•循环寿命（Cycle Life）：指铁锂电池能够进行循环充放电的次数，通常以充放电容量降至初始容量的80%作为结束标准。
•安全性（Safety）：指铁锂电池在正常使用和异常情况下具有的安全性能。
•电池管理系统（Battery Management System，BMS）：指对铁锂电池进行监控、平衡和保护的系统。
2. 技术要求2.1 电池性能•容量要求：铁锂电池的额定容量应满足设计要求，并且应保持一定的放电效率（通常不低于90%）。
•循环寿命：铁锂电池的循环寿命应达到或超过设计要求，通常不低于500次。
•充电速率：铁锂电池的充电速率应符合设计要求，通常不低于0.5C。
•安全性要求：铁锂电池的安全性能应满足国家相关标准和行业规范要求，包括但不限于电池短路、过充、过放和过温等安全保护。
2.2 生产工艺•原材料控制：确保采用高品质的正负极材料以及电解液和隔膜等辅助材料，并建立相应的供应链管理体系。
•生产工艺控制：确保生产过程的可控性和稳定性，包括但不限于搅拌、涂布、成型、焊接、封装等工艺环节。
•质量控制：建立完善的质量管控体系，包括原料检验、生产检验、成品检验和过程监控等，确保产品符合规定的技术要求。
LiFePO4 Battery
鋰鐵電池特性
高效率輸出：標準放電為2 5C、連續高電流放電可達10C， 高效率輸出：標準放電為2～5C、連續高電流放電可達10C，瞬間 10C 脈衝放電（10sec）可達20C 20C。 脈衝放電（10sec）可達20C。 極好的使用壽命， 500次迴圈 其放電容量仍大於95% 次迴圈， 95%。 極好的使用壽命，經500次迴圈，其放電容量仍大於95%。 安全性高，即使電池內部或外部受到傷害，電池不燃燒、不爆炸。 安全性高，即使電池內部或外部受到傷害，電池不燃燒、不爆炸。 耐熱程度佳，且可承受3~5C 甚至更高的充放電速度。 3~5C、 耐熱程度佳，且可承受3~5C、甚至更高的充放電速度。 高溫時性能良好：工作環境外部溫度65℃ 65℃時 高溫時性能良好：工作環境外部溫度65℃時，內部溫度將高達 95℃，電池放電結束時溫度可達160℃ 但電池的結構安全、 160℃， 95℃，電池放電結束時溫度可達160℃，但電池的結構安全、完 好。 過放電到零伏也無損壞。 過放電到零伏也無損壞。 可快速充電。 可快速充電。 鋰鐵電池原料沒有使用稀有金屬，可以大幅降低成本。 鋰鐵電池原料沒有使用稀有金屬，可以大幅降低成本。 對環境無污染。 對環境無污染。
LFP Battery Process
磷酸鋰鐵 (Cathode material)
分子式LiFePO4，又稱磷酸鐵鋰、鋰鐵磷，簡 稱LFP(三維橄欖石結構)
LFP Power Process
磷酸鋰鐵材料的合成可分為濕式法與乾式法兩 種，技術重點在配方與燒成控制。 一般生產工廠都配備攪拌機、氣氛燒成爐、研 磨機與篩分機等裝置。
2004年 2004年 3.2V 120-160 255 115 2000 2000 5~6
IFR 14500-450mAh 3.2V磷酸铁锂电池规格书超详细版
地址：省市坪山新区金荔科技园4栋DATE: TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 83962015/11/04地址：省市坪山新区金荔科技园4栋TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396DATE:2015/11/04Amendment Records（修正记录）Edition (版本) Description（记述）Prepared by（编制）Approved by（批准）Date（日期）A First Publish 时春2015/11/04地址：省市坪山新区金荔科技园4栋TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396DATE:2015/11/041Scope（适用围）This specification is applied to the reference battery in this Specification that manufactured by Yinkai Power Technology Co., Ltd.本说明书适用于本书中所提及的银凯动力科技制造的电池。
2Product Specification（产品技术规格）Table 1 (表1)No. (序号)Item（项目）General Parameter(常规参数)Remark（备注）1 Rated Capacity（额定容量）Typical（标称容量）450mAh Standard discharge（0.2C5A)after Standard charge（标准充电后0.2C5A标准放电）Minimum(最小容量)450mAh2 Nominal Voltage（正常电压）3.2VMean Operation Voltage（即工作电压）3Voltage at end ofDischarge（放电终止电压）2.0VDischarge Cut-off Voltage（放电截止电压）4 Charging Voltage(充电电压)3.65V5 出货电压≥3.28V6 Internal Impedance(阻)≤130mΩInternal resistance measured atAC 1KH Z after 50% charge（半电态下用交流法测量阻）The measure must uses the newbatteries that within one weekafter shipment and cycles lessthan 5 times(使用出货后不到一个星期及循环次数少于5次的新电池测量)7 Standard charge（标准充电）Constant Current 0.2C5AConstant Voltage 3.65V0.01 C cut-off（持续电流：0.2C5A持续电压：3.65V截止电流：0.01 C）8 Standard discharge（标准放电）Constant current 0.2C5Aend voltage 2.0V（持续电流：0.2C A地址：省市坪山新区金荔科技园4栋TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396DATE:2015/11/04 Continuous the table 1 (续表1)No. (序号)Item（项目）General Parameter(常规参数)Remark（备注）9 Fast charge(快速充电)Constant Current 0.5CConstant Voltage 3.65V0.01 C cut-off（持续电流：0.5C持续电压：3.65V截止电流：0.01 C）10 Fast discharge(快速放电)Constant current 1.0Cend voltage 2.0V（持续电流：1.0 C截止电压：2.0V）11 Maximum ContinuousCharge Current(最大充电持续电流)1.0 C12 Maximum ContinuousDischarge Current（最大放电持续电流）1.0 C13 Operation TemperatureRange（工作温度围）Charge（充电）: 0~45℃60±25%R.H.Bare Cell（电池储存湿度围）Discharge（放电）: -10~60℃14 Storage Temperature Range（储存温度围）Less than 1 year: -20~25℃（小于一年：-20~25℃）60±25%R.H.at the shipment state（出货状态时的湿度围）less than 3 months: -20~40℃（小于3个月：-20~40℃）Less than 1 month : -20~60℃（小于1个月：-20~60℃）15Weight电池重量About 20.0g16Cell Dimension（单体电芯尺寸）High/高度：50.0±0.4 mmInitial Dimension（初始尺寸）Diameter/直径: 14.1±0.2地址：省市坪山新区金荔科技园4栋DATE:TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 83962015/11/043Performance And Test Conditions (电池性能及测试条件)3.1 Standard Test Conditions（标准测试条件）Test should be conducted with new batteries within one week after shipment from our factory and the cells shall not be cycled more than five times before the test. Unless otherwise specified, test and measurement shall be done under temperature of 23±3℃and relative humidity of 45~85%. If it is judged that the test results are not affected by such conditions, the tests may be conducted at temperature 15~30℃and humidity 25~85%RH.测试必须使用出厂时间不超过一个星期的新电池，且未进行过五次以上的充放电循环。
LiFePO4BatterySpecifications磷酸铁锂电池组规格书-KAYO
Checked by / Date 审核
Prepared by/ Date 制作
Zeng xiang bo
Edition 版本
A
Description 描述
First Issue 首版发行
History of revisions 修订记录
Prepared by 制作
Approved by 批准
Date 日期
Client Confirmation 客户确认
Date / 日期
Page 1 of 13
深圳市嘉洋电池有限公司
SHEN ZHEN KAYO BATTERY CO., LTD
Contents / 主Байду номын сангаас内容
1.Scope / 适用范围-----------------------------------------------------------------------------------------------------------------3 2.Product configurations / 产品结构-------------------------------------------------------------------------------------------3 3.Product Dimensions / 产品尺寸----------------------------------------------------------------------------------------------3 4.Product Specifications / 产品规格--------------------------------------------------------------------------------------------5 5.Product Performance / 产品电性能------------------------------------------------------------------------------------------6 6.PCM Specifications / 保护板规格-------------------------------------------------------------------------------------------8 7.Security Test / 安全测试-------------------------------------------------------------------------------------------------------10 8.Storage and Transportation / 储存与运输---------------------------------------------------------------------------------11 e Attentions / 使用注意事项----------------------------------------------------------------------------------------12 10.Warranty / 品质保证----------------------------------------------------------------------------------------------------------13 11.Others / 其它事项-------------------------------------------------------------------------------------------------------------13 12.Note / 通知----------------------------------------------------------------------------------------------------------------------13 13 .App e nd i x/ 附件-- -- - - - -- - - - -- - - -- - - - -- - - - -- - - -- - - - -- - - - -- - - - -- - - -- - - - -- - - - -- - - -- - - - -- - - - -- - - - -- - 13
LiFePO4BatterySpecifications磷酸铁锂电池组规格书-KAYO
LiFePO4BatterySpecifications磷酸铁锂电池组规格书-KAYOCustomer /客户:LiFePO4Battery Specifications磷酸铁锂电池组规格书Model No./型号:25.6V100Ah-GSP09185190-100Ah-8S4PApproved by/Date批准Checked by /Date审核Prepared by/Date制作Zeng xiang boSHEN ZHEN KAYO BATTERY CO.,LTD.深圳市嘉洋电池有限公司Tel:+86-755-28117967,Fax:+86-755-28117957The 5th,11#Building,HuaLian Industrial Park,HuaNing Road,DaLang Community,LongHua Town,Shenzhen,P.R.China深圳市龙华新区⼤浪街道华宁路华联⼯业区11栋5楼/doc/bc516047db38376baf1ffc4ffe4733687e21fcec.htmlNote:1.Please kindly sign on the underneath and send it back to us if the samples have been approved.请帮忙在下⾯客户确认栏中签名并回传，如果样品通过了客户的测试。
2.Please kindly contact us as soon as possible if the samples can’t be approved.Thanks!请尽快与我们联系，如果样品没有通过客户的测试。
谢谢！Client Confirmation 客户确认Date /⽇期History of revisions修订记录Edition 版本Description描述Prepared by制作Approved by批准Date ⽇期AFirst Issue ⾸版发⾏2016-7-25Contents/主要内容1.Scope/适⽤范围-----------------------------------------------------------------------------------------------------------------32.Product configurations/产品结构-------------------------------------------------------------------------------------------33.Product Dimensions/产品尺⼨----------------------------------------------------------------------------------------------34.Product Specifications/产品规格--------------------------------------------------------------------------------------------55.Product Performance/产品电性能------------------------------------------------------------------------------------------66.PCM Specifications/保护板规格-------------------------------------------------------------------------------------------87.Security Test/安全测试-------------------------------------------------------------------------------------------------------108.Storage and Transportation/储存与运输---------------------------------------------------------------------------------11/doc/bc516047db38376baf1ffc4ffe4733687e21fcec.html e Attentions/使⽤注意事项----------------------------------------------------------------------------------------1210.Warranty/品质保证----------------------------------------------------------------------------------------------------------1311.Others/其它事项-------------------------------------------------------------------------------------------------------------1312.Note/通知----------------------------------------------------------------------------------------------------------------------1313.App e nd ix/附件---------------------------------------------------------------------------------131.Scope/适⽤范围This specification is applied to25.6V100Ah-GSP09185190-100Ah-8S4P battery Manufactured by SHEN ZHEN KAYO BATTERY CO.,LTD.本规格书是由深圳市嘉洋电池有限公司制作提供，适⽤的电池型号是25.6V100Ah-GSP09185190-100Ah-8S4P。
25.6V 200Ah LiFePO4 Battery Specification说明书
25.6V 200Ah LiFePO4 Battery Specification25.6V 200AhBattery Model： 25.6V200AHBattery Material： LiFePO4Nominal Voltage： 25.6VNominal Capacity： 200AH✓ Product PictureStock image may vary, multiple case options available✓ SpecificationItem SpecificationCell TypeCATL Brand LiFePO4 Prismatic Cell Nominal Capacity 200Ah Nominal voltage 25.6V Charge Cut-off Voltage 29.2V Discharge Cut-off Voltage 20.0V Maximum Charge Current 100AContinuous Discharge Current 150A (200A Optional) Peak Discharge Current 300A Communication Port RS485SOC Display LCD Voltage Display Battery HousingMetal case, white Operating temperatureCharging: 0℃~45℃Discharging: -10℃~60℃ Storage temperature -5℃~35℃ Storage Humidity≤75% RHEnvironmental conditionTemperature ：25±2℃Humidity: 45-75%RHAtmospheric Pressure: 86-106 KPADischarge/Charge connector Screw In TerminalsSize (Custom Cases Available)500 (L) x 260 (W) x 230 (H) (mm) 20(L) x 10.2 (W) x 9 (H) (inches)Net WeightApprox.: 50kg / 110lbsGeneral PerformanceItem Test Methods and Condition Criteria0.2C Capacity After standard charging, hold battery for 10mins, thendischarge at 0.2C to voltage 21.0V, recording the dischargingtime.≥201AhCycle Life Constant current 0.2C charge to 29.2V, then constant voltagecharge to current declines to 0.01C, rest 10min constant current0.5C discharge to 20.0V rest 10min.Repeat above steps till continuous discharging capacity Higherthan 70% of the Initial Capacities of the Cells≥5000 timesCapability of storing electricity 20+/-5℃, After standard charging, hold the battery for 28days,then discharge at 0.2C rate to voltage 21.0V, recording thedischarging time.≥240min✓Environment PerformanceItem Test Methods and Condition CriteriaDischarge at high temperature After standard charging, shelve the cells 4h at 60+/-2℃,then discharging at 1C to voltage 21.0V, recording the discharging time.≥54minDischarge at low temperature After standard charging, shelve the cells for 16h at -20+/2℃, then discharging at 0.2C to voltage 21.0V,recording the discharging time.≥210minThermal shock Put the battery cells in the dryer box.The temperature of the oven is to be raised at 5+/-2℃per minute to a temperature of 100+/-2℃ and remains 30minutes.No fire, nosmoke✓Safe CharacteristicItem Test Methods and Condition CriteriaOver charge testing At 23+/-5℃, charging cells with constant current 2C tovoltage 29.2V, Stop test till cells temperature 10°C lowerthan max temperature.No smoke orfireOver discharge testing At 23+/-5℃, According to the requirements of standardcharge, the cells will be discharge to cut-off voltage, thenconnect with external load of 30 ohm for 24 hours.No fire, nosmoke, noleakage.Short-circuit testing At 23+/-5℃, After standard charging, connect cells anodeand cathode by wire which impedance less than 200+/-20mΩ, shelve the battery for 6 hours.No smoke orfire※Above testing of safe characteristic must be with protective equipment.CAUTIONS IN USETo ensure proper use of the battery please read the manual carefully before using it. Handling ▪ Do not expose to, dispose of the battery in fire.▪ Do not put the battery in a charger or equipment with wrong terminals connected.▪ Avoid shorting the battery▪ Avoid excessive physical shock or vibration.▪ Do not disassemble or deform the battery.▪ Do not immerse in water.▪ Do not use the battery mixed with other different make, type, or model batteries.▪ Keep out of the reach of children.✓Charge and Discharge▪ Battery must be charged in appropriate charger only.▪ Never use a modified or damaged charger.▪ Do not leave battery in charger over 24 hours.✓Storage▪ Store the battery in a cool, dry and well-ventilated area.✓Disposal▪ Regulations vary for different countries. Dispose of in accordance with local regulations.✓Battery operation instruction★ChargingCharging current Cannot surpass the biggest charging current which in this specification book stipulated.Charging voltage Does not have to surpass the highest voltage range which in this specification book stipulated.Charge temperature The battery must carry on the charge in the ambient temperature scope which this specification book stipulated.Uses the constant electric current, and the constant voltage way charge, the prohibition reverse charges. Incorrect connection of the battery positive electrode and the negative terminal can damage the battery.★Discharging currentThe discharging current does not have to surpass this specification book stipulation the biggest discharging current, the oversized electric current electric discharge can cause the battery capacity reduction and to cause the battery overheat.★Discharge temperatureThe battery discharge must carry on in the ambient temperature scope which this specification book stipulated.★Over-dischargesAfter the short time excessively discharges charges immediately cannot affect the use, but the long time excessively discharges can cause the battery the performance, battery function losing. The battery long-term has not used, has the possibility to be able to be at because of its automatic flashover characteristic certain excessively discharges the condition, for prevented excessively discharges the occurrence, the battery should maintain the certain electric quantity.★Storing the BatteriesThe battery should store in the product specification book stipulation temperature range. If has surpasses above for one months the long-time storage, suggested you should carry on additional charge to the battery.✓Other The Chemical ReactionBecause batteries utilize a chemical reaction, battery performance will deteriorate over time even if stored for a long period of time without being used.In addition, if the various usage conditions such as charge, discharge, ambient temperature, etc. are not maintained within the specified ranges the life expectancy of the battery may be shortened or the device in which the battery is used may be damaged by electrolyte leakage. If the batteries cannot maintain a charge for long periods of time, even when they are charged correctly, this may indicate it is time to change the battery.✓NOTICEBefore using the battery pack/packs, pls DO NOTE BELOW REMINDINGS:# Battery appearance visual check:Carefully open the protective carton/wooden box Once batteries received.Pls do check if the batteries with any scratches or impacted.If everything goes well, pls go on.If any, pls contact us at the very first time without any delay.# Do correctly connect the battery with Positive Pole and Negative Pole (usually Red + Black -). Otherwise short circuit would possibly happen due to wrong connection on +/- terminal.# Connection Use Notice:Do keep the battery packs within 1.0VDC voltage difference if you are going to connect them in series or parallel. The smaller voltage difference (0.1V-1.0V) of the battery packs the better for batteries connection.# DO NOT discharge the battery pack till 0% Power which is not that good to keep longer life. Pls charge the battery to 80% (100% would also be fine) and DO Recharge the Battery while they are discharged/used down to 20% Power.# DO Recharge the Battery Packs every 3 months if they are shelved/not used for long time.。
IFR-32650-5000mAh-3.2V磷酸铁锂规格书
地址：广东省深圳市坪山新区金荔科技园4栋TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396 DATE: 2015/04/09Cylindrical LIFEPO4 BatterySpecification圆柱型磷酸铁锂电池规格书MODEL/型号: IFR 32650-5000mAh 3.2VPrepared By/Date 编制/日期Checked By/Date审核/日期Approved By/Date批准/日期冯时春/2015.04.09Customer Approval 客户批准Signature确认Date日期Company Name：公司名称：Company Stamp：客户印章：--- 保密文件---地址：广东省深圳市坪山新区金荔科技园4栋TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396 DATE: 2015/04/09Amendment Records （修正记录）Edition (版本) Description（记述）Prepared by（编制）Approved by（批准）Date（日期）A First Publish 冯时春2015/04/09地址：广东省深圳市坪山新区金荔科技园4栋TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396 DATE: 2015/04/091 Scope（适用范围）This specification is applied to the reference battery in this Specification that manufactured by Yinkai Power Technology Co., Ltd.本说明书适用于本书中所提及的银凯动力科技有限公司制造的电池。
2 Product Specification（产品技术规格）Table 1 (表1)No. (序号)Item（项目）General Parameter(常规参数)Remark（备注）1 Rated Capacity（额定容量）Typical（标称容量）5000mAh Standard discharge（0.2C5A)after Standard charge（标准充电后0.2C5A标准放电）Minimum(最小容量)4750mAh2 Nominal Voltage（正常电压）3.2VMean Operation Voltage（即工作电压）3 Voltage at end ofDischarge（放电终止电压）2.5VDischarge Cut-off Voltage（放电截止电压）4 Charging Voltage(充电电压)3.65V5 Internal Impedance(内阻)≤10mΩInternal resistance measured atAC 1KH Z after 50% charge（半电态下用交流法测量内阻）The measure must uses thenew batteries that within oneweek after shipment and cyclesless than 5 times(使用出货后不到一个星期及循环次数少于5次的新电池测量)6 Standard charge（标准充电）Constant Current 0.2C5AConstant Voltage 3.65V0.01 C cut-off（持续电流：0.2C5A持续电压：3.65V截止电流：0.01 C）7 Standard discharge（标准放电）Constant current 0.2C5Aend voltage 2.5V（持续电流：0.2C5A截止电压：2.5V）地址：广东省深圳市坪山新区金荔科技园4栋TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396 DATE: 2015/04/09Continuous the table 1 (续表1)No. (序号)Item（项目）General Parameter(常规参数)Remark（备注）8 Fast charge(快速充电)Constant Current 0.5CConstant Voltage 3.65V0.01 C cut-off（持续电流：0.5C持续电压：3.65V截止电流：0.01 C）9 Fast discharge(快速放电)Constant current 1.0Cend voltage 2.5V（持续电流：1.0 C截止电压：2.5V）10 Maximum ContinuousCharge Current(最大充电持续电流)1.0 C11 Maximum ContinuousDischarge Current（最大放电持续电流）1.5 C12 Operation TemperatureRange（工作温度范围）Charge（充电）: 0~45℃60±25%R.H.Bare Cell（电池储存湿度范围）Discharge（放电）: -10~60℃13 Storage TemperatureRange（储存温度范围）Less than 1 year: -20~25℃（小于一年：-20~25℃）60±25%R.H.at the shipment state（出货状态时的湿度范围）less than 3 months: -20~40℃（小于3个月：-20~40℃）Less than 7 day : -20~65℃（小于7天：-20~65℃）14Cell Dimension（单体电芯尺寸）High/高度：70±0.2mmInitial Dimension（初始尺寸）Diameter/直径: 32.2±0.5 mm地址：广东省深圳市坪山新区金荔科技园4栋TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396 DATE: 2015/04/093 Performance And Test Conditions (电池性能及测试条件)3.1 Standard Test Conditions（标准测试条件）Test should be conducted with new batteries within one week after shipment from our factory and the cells shall not be cycled more than five times before the test. Unless otherwise specified, test and measurement shall be done under temperature of 23±3℃and relative humidity of 45~85%. If it is judged that the test results are not affected by such conditions, the tests may be conducted at temperature 15~30℃and humidity 25~85%RH.测试必须使用出厂时间不超过一个星期的新电池，且未进行过五次以上的充放电循环。
Lithium Ion AA型电池说明书
Lithium Ion Battery SpecificationsType: Normal Cylindrical Battery Model: LC-14500AA Portable Power CorpDba 825 S 19th Street, Richmond, CA 94804Tel: 510-525-2328Product SpecificationsType ---------------------- Normal Cylindrical BatteryModel--------------------- LC-14500Dimension (Including shrink sleeve/label)Diameter, d ---------------------- 14.1±0.2mmHeight, h ------------------------- 48.5±0.5mmWeight--------------------------- 20g (Approx)Nominal voltage -------------- 3.7V0.2C Capacity (0.2C discharge)Nominal---------------------- 750mAhMinimum ----------------------- 750mAhMaximum charge voltage 4.2VMax .continuous charge current750mAMaximum discharge currentContinuous----------------------- 1500mADischarge cut-off voltage--- 2.75VInternal impedance (23±2°C) ≤75mΩOperation temperatureDischarge------------------------- -20-60°CCharge------------------------------ 0-45°CStorage temperature(non-condensing)Within 1month------------------ 0-45°C1-3months----------------------- 0-35°C3-12months--------------------- 0-25°C1. ScopeThis specification shall be applied to Lithium ion rechargeable battery cell supplied by AA Portable Power Corp.2. Testing EnvironmentUnless otherwise specified, all tests stated in this document shall be performed at 23±2°C3. Performance and Test ConditionsStandard charge: 0.5C=375mA constant current (CC) charge to 4.2V, followed by 4.2V constant voltage (CV) charge until current taper to ≤0.01C.Standard discharge: 0.5C=375mA CC discharge to the end of discharge voltage.No.Test item Test conditions Requirements 3.1Outside Appearance Visual check No prominent stainand deformation, nordamage.3.2Outside Dimensions Vernier clippers Diameter14.1±0.2 mmHeight48.5±0.5 mm3.3Open circuit voltageat deliveryVoltage is tested within 1 week after delivery 3.75V or more3.4Internalresistance atdelivery The cell impedance shall be measuredby AC method (1kHz) within 1 weekafter delivery.75mΩ or less3.5Nominal capacity At standard charging (CH) and discharging at 0.2C750mAh or more3.6Temperature-rateperformance 1)Standard CH at R.TKeep batteries in a icebox with ambient temperature of-20°C for 4 hours.DCH at 0.2C to the end of DCH voltage at -20°C;Calculate the capacity ratio with the nominal capacity.2)Standard CH at R.TKeep batteries in a icebox with ambient temperature of0°C for 4 hours.Capacity ratio ≥50%Capacity ratio≥75%Standard DCH to the end of DCH voltage at 0°C;Calculate the capacity ratio with the nominal capacity.3)Standard CH at RTKeep batteries in a icebox with ambient temperature of60°C for 4 hours.Standard DCH to the end of DCH voltage at 60°C;Calculate the capacity ratio with the nominal capacity..Capacity ratio ≥95%3.7Cycle Life300次循环。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
DATE: 2017/02/23
No. (序号)
Item （项目）
General Parameter (常规参数)
Remark （备注）
8
Fast charge (快速充电)
9
Fast discharge (快速放电)
Constant Current 0.5C Constant Voltage 14.6V
SHENZHEN YINKAI POWER TECHNOLOGY Co., Ltd
地址：广东省深圳市坪山新区坪葵路 216 号 TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396
VER: A
DATE: 2017/02/23
Edition (版 本)
A
Amendment Records （修正记录）
Maximum Continuous
11
Discharge Current
（最大放电持续电流）
100A
Operation Temperature
Charge（充电）: 0~45℃
60±25%R.H.
12
12.8V
Mean Operation Voltage （即工作电压）
Voltage at end of
3
Discharge
（放电终止电压）
10.0V
Discharge Cut-off Voltage （放电截止电压）
4
Charging Voltage (充电电压)
14.6V
Internal resistance measured at AC 1KHZ after 50% charge
end voltage 10.0V （持续电流：0.2C5A
截止电压：10.0V）
Page 3 of 12
第 4 页 共 12 页
深 圳 市 银 凯 动 力 科 技 有 限 公 司 VER: A
SHENZHEN YINKAI POWER TECHNOLOGY Co., Ltd
地址：广东省深圳市坪山新区坪葵路 216 号 TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396
地址：广东省深圳市坪山新区坪葵路 216 号 TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396
VER: A
DATE: 2017/02/23
1 Scope（适用范围） This specification is applied to the reference battery in this Specification that manufactured by
Description （记 述）
Prepared by Approved by
Date
（编 制）
（批 准） （日 期）
First Publish
刘晓军
2017/02/23
Page 2 of 12
第 3 页 共 12 页
深圳市银凯动力科技有限公司
SHENZHEN YINKAI POWER TECHNOLOGY Co., Ltd
Cylindrical LIFEPO4 Battery Specification
圆柱型磷酸铁锂电池规格书
MODEL/型号: IFR26650 100Ah 12.8V(4S34P)
Prepared By/Date 编 制/日 期
刘晓军/2017.02.23
Checked By/Date 审 核/日 期
Yinkai Power Technology Co., Ltd.
本说明书适用于本书中所提及的银凯动力科技有限公司制造的电池。
2 Product Specification（产品技术规格）
Table 1 (表 1)
No. (序号)
Item （项目）
General Parameter (常规参数)
Remark （备注）
Approved By/Date 批 准/日 期
Signature 确认
Date 日期
Customer Approval 客户批准
Company Name： 公司名称：
Company Stamp： 客户印章：
--- 保密文件 ---
Page 1 of 12
第 2 页 共 12 页
深圳市银凯动力科技有限公司
Constant Current 0.2C5A
Constant Voltage 14.6V
6
Standard charge （标准充电）
0.01 C cut-off （持续电流：0.2C5A
持续电压：14.6V
截止电流：0.01 C）
Constant current 0.2C5A
7
Standard discharge （标准放电）
0.01 C cut-off （持续电流：0.5C 持续电压：14.6V 截止电流：0.01 C）
Constant current 1.0C end voltage 10.0V （持续电流：1.0 C 截止电压：10.0V）
Maximum Continuous
10
Charge Current
50A
(最大充电持续电流)
1
Rated Capacity （额定容量）
Typical （标称容量）
Minimum (最小容量)
100Ah 95Ah
Standard discharge（0.2C5A) after Standard charge
（标准oltage （正常电压）
（半电态下用交流法测量内阻）
5
Internal Impedance (内阻)
≤200mΩ
The measure must uses the new batteries that within one week after shipment and cycles
less than 5 times (使用出货后不到一个星期及循 环次数少于 5 次的新电池测量)
第 1 页 共 12 页
深圳市银凯动力科技有限公司
SHENZHEN YINKAI POWER TECHNOLOGY Co., Ltd
地址：广东省深圳市坪山新区坪葵路 216 号 TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396
VER: A
DATE: 2017/02/23