与机械有关英语单词
机械英语单词综述
board n.板卡fine adj.精密的word n.字ABS(absolute) adj.绝对的absolute adj.绝对的AC n.交流accelerate v.加速acceleration n.加速度active adj.有效的adapter n.适配器，插头address n.地址adjust v.调整adjustment n.调整advance v.前进advanced adj.高级的，增强的alarm n.报警ALM(alarm) n.报警alter v.修改amplifier n.放大器angle n.角度APC n.绝对式脉冲编码器appendix n.附录，附属品arc n.圆弧argument n.字段，自变量arithmetic n.算术arrow n.箭头AUTO n.自动automatic adj.自动的automation n.自动auxiliary function 辅助功能axes n.轴（复数）axis n.轴background n.背景，后台backlash n.间隙backspace v.退格backup v.备份bar n.栏，条battery n.电池baudrate n.波特率bearing n.轴承binary adj..二进制的bit n.位blank n.空格block n.块，段block n.撞块，程序段blown v.熔断bore v.镗boring n.镗box n.箱体，框bracket n.括号buffer n.v.缓冲bus n.总线button n.按钮cabient n.箱体calbe n.电缆calculate v.计算calculation n.计算call v.调用CAN(cancel) v.清除cancel v.清除canned cycle 固定循环capacity n.容量card n.板卡carriage n.床鞍，工作台cassette n.磁带cell n.电池CH(chanel) n.通道change v.变更，更换channel n.通道check v.检查chop v.錾削chopping n.錾削circle n.圆circuit n.电路，回路circular adj.圆弧的clamp v.夹紧clear v.清除clip v.剪切clip board n.剪贴板clock n.时钟clutch n.卡盘，离合器CMR n.命令增益CNC 计算机数字控制code n.代码coder n.编码器command n,v.命令communication n.通讯compensation n.补偿computer n.计算机condition n.条件configuration n.配置configure v.配置connect v.连接connection n.连接connector n.连接器console n.操作台constant n.常数，adj.恒定的contour n.轮廓control v.控制conversion n.转换cool v.冷却coolant n.冷却coordinate n.坐标copy v.拷贝corner n.转角correct v.改正，adj.正确的correction n.修改count v.计数counter n.计数器CPU n.中央处理单元CR n.回车cradle n.摇架create v.生成CRT n.真空射线管CSB n.中央服务板current n.电流，当前的，缺省的current loop n.电流环cursor n.光标custom n.用户cut v.切削cutter n.（元盘形）刀具cycle n.循环cylinder n.圆柱体cylindrical adj.圆柱的data n.数据（复数）date n.日期datum n.数据（单数）DC n.直流deceleration n.减速decimal point n.小数点decrease v.减少deep adj.深的define v.定义deg. n.度degree n.度DEL(delete) v.删除delay v,n.延时delete v.删除deletion n.删除description n.描述detect v.检查detection n.检查device n.装置DGN(diagnose) v.诊断DI n.数字输入DIAG(diagnosis) n.诊断diagnosis n.诊断diameter n.直径diamond n.金刚石digit n.数字dimension n.尺寸，（坐标系的）维DIR n.目录direction n.方向directory n.目录disconnect v.断开disconnection n.断开disk n.磁盘diskette n.磁盘display v,n.显示distance n.距离divide n,v除，v.划分DMR n.检测增益DNC 直接数据控制DO n.数字输出dog switch n.回参考点减速开关DOS n.磁盘操作系统DRAM n.动态随机存储器drawing n.画图dress v.修整dresser n.修整器drill v.钻孔drive v.驱动driver n.驱动器dry run 空运行duplicate v.复制duplication n.复制dwell n,v.延时edit v.编辑EDT(edit) v.编辑EIA n.美国电子工业协会标准electrical adj.电气的electronic adj.电子的emergency n.紧急情况enable v.使能encoder n.编码器end v,n.结束enter n.回车，v.输入，进入entry n.输入equal v.等于equipment n.设备erase v.擦除error n.误差，错误，故障esc=escape v.退出exact adj.精确的example n.例子exchange v.更换execute v.执行execution n.执行exit v.退出external adj.外部的failure n.故障FANUC n.（日本）法那克fault n.故障feed v.进给feedback v.反馈feedrate n.进给率figure n.数字file n.文件filt(filtrate) v.过滤filter n.过滤器fin(finish) n.完成（应答信号）fine adj.精密的fixture n.夹具FL （回参考点的）低速flash memory n.闪存flexible adj.柔性的floppy adj.软的foreground n.前景，前台format n.格式，v.格式化function n.功能gain n.增益GE FANUC GE法那克gear n.齿轮general adj.总的，通用的generator n.发生器geometry n.几何gradient n.倾斜度，梯度graph n.图形graphic adj.图形的grind v.磨削group n.组guidance n.指南，指导guide v.指导halt n,v.暂停，间断handle n.手动，手摇轮handy adj.便携的handy file 便携式编程器hardware n.硬件helical adj.螺旋上升的help n,v.帮助history n.历史HNDL(handle) n.手摇，手动hold v.保持hole n.孔horizontal a.水平的host n.主机hour n.小时hydraulic adj.液压的I/O n.输入/输出illegal adj.非法的inactive adj.无效的inch n.英寸increment n.增量incremental adj.增量的index 分度，索引initial adj.原始的initialization n.C523初始化initialize v.初始化input n.v.输入INS(insert) v.插入insert v.插入instruction n.说明interface n.接口internal adj.内部的interpolate v.插补interpolation n.插补interrupt v.中断interruption n.中断intervent n.间隔，间歇involute n.渐开线ISO n.国际标准化组织jog n.点动jump v.跳转key n.键keyboard n.键盘label n.标记，标号ladder diagram 梯形图language n.语言lathe n.车床LCD n.液晶显示least adj.最小的length n.长度LIB(library) n.库library n.库life n.寿命light n.灯limit n.极限limit switch n.限位开关line n.直线linear adj.线性的linear scale n.直线式传感器link n,v.连接list n,v.列表load n.负荷，v.装载local adj.本地的locate v.定位，插销location n.定位，插销lock v.锁定logic n.逻辑look ahead v.预，超前loop n.回路，环路LS n.限位开关LSI n.大规模集成电路machine n.机床，v.加工macro n.宏macro program n.宏程序magazine n.刀库magnet n.磁体，磁magnetic a.磁的main program n.主程序maintain v.维护maintenance n.维护MAN(manual) n.手动management n.管理manual n.手动master adj.主要的max adj.最大的，n.最大值maximum adj.最大的，n.最大值MDI n.手动数据输入meaning n.意义measurement n.测量memory n.存储器menu n.菜单message n.信息meter n.米metric adj.米制的mill n.铣床，v.铣削min adj.最小的,n.最小值minimum adj.最小的,n.最小值minus v.减,adj.负的minute n.分钟mirror image n.镜像miscellaneous function n.辅助功能MMC n.人机通讯单元modal adj.模态的modal G code n.模态G代码mode n.方式model n.型号modify v.修改module n.模块MON(monitor) v.监控monitor v.监控month n.月份motion n.运动motor n.电机mouse n.鼠标MOV(移动） v.移动move v.移动movement n.移动multiply v.乘N number n.程序段号N.M n.牛顿.米name n.名字NC n.数字控制NCK n.数字控制核心negative adj.负的nest v,n.嵌入，嵌套nop n.空操作NULL n.空number n.号码numeric adj.数字的O number n.程序号octal adj.八进制的OEM n.原始设备制造商OFF adv.断offset n.补偿，偏移量ON adv.通one shot G code 一次性G代码open v.打开operate v.操作operation n.操作OPRT(operation) n.操作origin n.起源，由来original adj.原始的output n,v.输出over travel 超程over voltage 过电压overcurrent 过电流overflow v,n.溢出overheat n.过热overload n.过负荷override n.（速度等的）倍率page n.页page down 下翻页page up 上翻页PARA(parameter) n.参数parabola n.抛物线parallel adj.平行的，并行的，并联的parameter n.参数parity n.奇偶性part n.工件，部分password n.口令，密码paste v.粘贴path n.路径pattern n.句型，式样PC n.个人电脑PCB n.印刷电路板per prep.每个percent n.百分数pitch n.节距，螺距plane n.平面PLC n.可编程序逻辑控制器plus n.增益，prep.加,adj.正的PMC n.可编程序逻辑控制器pneumatic adj.空气的polar adj.两极的，n.极线portable adj.便携的POS(position) v,n.位置，定位position v,n.位置，定位position loop n.位置环positive adj.正的power n.电源，能量，功率power source n.电源preload v.预负荷preset v.予置pressure n.压力preview v.予览PRGRM(program) v.编程，n.程序print v.打印printer n.打印机prior adj.优先的，基本的procedure n.步骤profile n.轮廓，剖面program v.编程，n.程序programmable adj.可编程的programmer n.编程器protect v.保护protocol n.协议PSW(password) n.密码，口令pulse n.脉冲pump n.泵punch v.穿孔puncher n.穿孔机push button n.按钮PWM n.脉宽调制query n.问题，疑问quit v.退出radius n.半径RAM n.随机存储器ramp n.斜坡ramp up v.（计算机系统）自举range n.范围rapid adj.快速的rate n.比率，速度ratio n.比值read v.读ready adj.有准备的ream v.铰加工reamer n.铰刀record v,n.记录REF(reference) n.参考reference n.参考reference point n.参考点register n.寄存器registration n.注册，登记relative adj.相对的relay v,n.中继remedy n.解决方法remote adj.远程的replace v.更换，代替reset v.复位restart v.重启动RET(return) v.返回return v.返回revolution n.转rewind v.卷绕rigid adj.刚性的RISC n.精简指令集计算机roll v.滚动roller n.滚轮ROM n.只读存储器rotate v.旋转rotation n.旋转rotor n.转子rough adj.粗糙的RPM n.转/分RSTR(restart) v.重启动run v.运行sample n.样本，示例save v.存储save as 另存为scale n.尺度，标度scaling n.缩放比例schedule n.时间表，清单screen n.屏幕screw n.丝杠，螺杆search v.搜索second n.秒segment n.字段select v.选择selection n.选择self-diagnostic 自诊断sensor n.传感器sequence n.顺序sequence number 顺序号series n.系列，adj.串行的series spindle n.数字主轴servo n.伺服set v.设置setting n.设置shaft n.轴shape n.形状shift v.移位SIEMENSE （德国）西门子公司sign n.符号，标记signal n.信号skip v,n.跳步slave adj.从属的SLC n.小型逻辑控制器slide n.滑台,v.滑动slot n.槽slow adj.慢soft key n.软键盘software n.软件space n.空格，空间SPC n.增量式脉冲编码器speed n.速度spindle n.主轴SRAM n.静态随机存储器SRH(search) v.搜索start v.启动statement n.语句stator n.定子status n.状态step n.步stop v.停止,n.挡铁store v.储存strobe n.选通stroke n.行程subprogram n.子程序sum n.总和surface n.表面SV(servo) n.伺服switch n.开关switch off v.关断switch on v.接通symbol n.符号，标记synchronous adj.同步的SYS(system) n.系统system n.系统tab n.制表键table n.表格tail n.尾座tandem adv.一前一后，串联tandem control n.纵排控制（加载预负荷的控制方式）tank n.箱体tap n,v.攻丝tape n.磁带，纸带。
与机械有关英语单词
组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet柳丁table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA（out of box audit）开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC(quality control)品管质量控制supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP(standard operatingprocedures)制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线精品left fork叉车personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener 整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller??床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vicemanager副理section supervisor课长deputy section supervisor=vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, tohandle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料精品to unload material卸料to return material/stock to 退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/generalaffairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车精品forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a littlebigger尺寸偏大(小)cosmetic defect外观不良slippedscrewhead/slippery screwhead螺丝滑头slippedscrewhead/shippery screwthread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边精品poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surfaceprocessing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan =enterprise expansionprojects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products,up-to-grade products良品defective products, notup-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模精品to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing 压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, notqualified不合格material change, stockchange材料变更feature change 特性变更evaluation评估prepare for, makepreparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to,switch---to throw--overswitching over切换engineering, projectdifficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器精品die lifter举模器argon welding氩焊vocabulary for stamping 冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener 整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locatingpiece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine andverify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and handin提报safe stock安全库存acceptance = receive验收to notice通知application form forpurchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角精品character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate 移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary fordie engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow(-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=sidescrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板精品spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physicalinvetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accountingdepartment for reference会计部存查end-user/usingunit(department)使用单位summary of year-endphysical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physicalinventory list will be sentto accountingdepartment together(Those of NHK will besent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status recordsof year-end physicalinventory List andphysical inventory card年终盘点卡与清册使用－状况明细表blank and waste sheetNO.空白与作废单号plate电镀mold成型material for engineeringmold testing工程试模材料精品not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by/ prepared by核准/审核/承办PCE assembly productionschedule sheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production controlconfirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected orreworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表精品notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/acceptedgoods/ acceptedparts/good parts良品defectiveproduct/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physicalinventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=diebutton圆冲子shape punch=die insert异形子精品stock locater block定位块under cut=scrap chopper 清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线精品heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=intera ction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火精品annealing退火carbonization碳化alloy合金tungsten high speed steel 钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高精品die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool 等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子精品bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具精品移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口精品Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output qualitycontrol 最终出货品质管制人员IQC incoming qualitycontrol 进料品质管制人员TQC total qualitycontrol 全面质量管理POC passage qualitycontrol 段检人员QA quality assurance质量保证人员OQA output qualityassurance 出货质量保证人员QE quality engineering品质工程人员品质保证类FAI first articleinspection 新品首件检查FAA first articleassurance 首件确认TVR tool verificationreport 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index ofprocess 模具制程能力参数SSQA standardizedsupplier quality 合格供应商品质评估OOBA out of box audit开箱检查QFD quality functiondeployment 品质机能展开FMEA failure modeleffectiveness analysis 失效模式分析精品8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average OutputQuality 平均出厂品质AOQL Average OutputQuality Level 平均出厂品质Q/R/SQuality/Reliability/Service 品质/可靠度服务MIL-STDMilitary-Standard 军用标准S I-S IV SpecialI-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept OnDeviation 特采UAI Use As It 首件检查报告FPIR First PieceInspection Report 百万分之一PPM Percent PerMillion 批号制程统计品管专类SPC Statistical ProcessControl 统计制程管制SQC Statistical QualityControl 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper CentralLimit 管制上限LCL Lower CentralLimit 管制下限MAX Maximum 最大值精品MIN Minimum 最小值精品GRR Gauge Reproducibility&Repeatab ility 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do CheckAction 计划执行检查总结ZD Zero Defect 零缺点QI QualityImprovement 品质改善QP Quality Policy 目标方针TQM Total QualityManagement 全面品质管理MRB Material RejectBill 退货单LQL Limiting QualityLevel 最低品质水准RMA Return MaterialAudit 退料认可QAN QualityAmelionrate Notice 品质改善活动ADM AbsoluteDimension Measuremat全尺寸测量QT Quality Target 品质目标7QCTools 7 QualityControll Tools 品管七大手法通用之件类ECN EngineeringChange Notes 工程变更通知(供应商)ECO EngineeringChange Order 工程改动要求(客户)PCN Process ChangeNotice 工序改动通知PMP ProductManagement Plan 生产管制计划SIP Specification InProcess 制程检验规格SOP StandardOperation Procedure 制精品造作业规范精品IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China GeneralPCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS InternationalWorkman Standard 工艺标准ISO InternationalStandard Organization国际标准化组织GS GeneralSpecification 一般规格CMCS C-ChinaM-Manufact C-CompaqS-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-QualityA-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-PaintingCompaq产品在龙华烤漆厂品管作业规范部类PMC Production &Material Control 生产和物料控制PPC Production PlanControl 生产计划控制MC Material Control物料控制ME ManafactureEngineering 制造工程部精品PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课) PD ProductDepartment 生产部LAB Labratry 实验室IE IndustrialEngineering 工业工程R&D Research &Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order采购订单MO Manufacture Order生产单D/C Date Code 生产日期码ID/C IdentificationCode (供应商)识别码SWR Special WorkRequest 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM OriginalEquipment Manufacture原设备制造PCE Personal ComputerEnclosure 个人电脑外设PC Personal Computer个人电脑CPU Central ProcessingUnit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料精品NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-staticDischarge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM CompactDisk Read-Only Memory只读光碟FDD Floppy Disk Drive软碟机HDD Hard Disk Drive碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer AidDesign 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit集成电路精品T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间) S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy QualityAssurance 策略品质保证DQA Desigh QualityAssurance 设计品质保证MQA ManufactureQuality Assurance 制造品质保证SSQA Sales and serviceQuality Assurance 销售及服务品质保证LRR Lot Rejeet Rate批退率BS Brain storming 脑力激荡EMI ElectronicMagnetion Inspect 高磁测试FMI FrequencyModulatim Inspect 高频测试B/M Boar/Molding(flatcable)C/P Connector of PCA/P AssemblySPS Switching powersupply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)精品DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS ComplemeruaryMetoll OxideSemiconductor 互补金属氧化物半导体PDA Personal DigitalAssistant 个人数字助理IC Integrated Circuit集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro ChannelArchitecture 微通道结构EISA ExtendedIndustry StandardArchitecture 扩充的工业标准结构SIMM Single in-linememory module 单项导通汇流组件DIMM Dual in-lineMemory Module 双项导通汇流组件LED Light-EmittingDiode 发光二级管FMEA Failure ModeEffectivenes 失效模式分析W/H Wire Harness金属线绪束集组件F/C Flat Calle 排线PCB Printed CircuitBoard 印刷电路板CAR Correction ActionReport 改善报告NG Not Good 不良WPR Weekly DeliveryRequirement 周出货要求PPM Parts Per Million百万分之一TPM Total Production精品Maintenance 全面生产保养精品MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing Change P/P Plans & Procedune EMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material Condition MMS MaximumMaterial SizeLMC Least MaterialConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metalforging 粉末锻造cold chamber die casting冷式压铸precisionforging 精密锻造cold forging 冷锻pressforging 冲锻compacting molding 粉末压出成形rocking dieforging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotationalmolding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand moldcasting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻sixsides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形精品hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mouldthermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold料套式模具center-gated mold 中心浇口式模具loose detailmold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold多模穴模具electroformed mold 电铸成形模multi-gate mold复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold通气性模具精品duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectionaldie 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套singlecavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball精品plunger 定位球塞精品ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体diebody 铸模座die bush 合模衬套diebutton 冲模母模die clamper 夹模器diefastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowelhole 导套孔dowel pin 合模梢dozzle辅助浇口dowel pin 定位梢draft拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆精品。
机械英语单词汇总
1, Nanometallic 纳米金属2, metallic glasses金属玻璃3, material extrusion 材料挤制成型技术4, additive manufacturingn. 增材制造；添加剂制造5, control algorithm [计] 控制算法6, scanner ['skænə]n. [计] 扫描仪；扫描器；光电子扫描装置7, sensor ['sensə]n. 传感器8, function ['fʌŋ(k)ʃ(ə)n]n. 功能；[数] 函数；9, time delay [time+delay]延时，延迟10, computation [kɒmpjʊ'teɪʃ(ə)n]n. 估计，计算11, continuous track 持续追踪12, alloy ['ælɔɪ]n. 合金13, electrical discharge machining电火花加工14, fabrication [fæbrɪ'keɪʃ(ə)n]制备15, titanium [taɪ'teɪnɪəm; tɪ-]n. [化学] 钛（金属元素）16, penetration [penɪ'treɪʃ(ə)n]n. 渗透；突破；侵入；洞察力17, intensity [ɪn'tensɪtɪ]n. 强度18, graphitization [,ɡræfitai'zeiʃən, -ti'z-] n. [化工][冶] 石墨化19, three-dimensionaladj. 三维的；立体的；真实的20, carbon diffusion 碳扩散21, single-crystal diamond 单晶金刚石22, surface integrity [surface+integrity]表面完整性；表面质量23, diamond ['daɪəmənd] 钻石金刚石24, microstructured 微观构造25, physiotherapy [,fɪzɪo'θɛrəpi]物理疗法26, randomised trials 随机试验27, ion etching 离子浸蚀离子蚀刻28, ion excitation 离子激发29, telemedicine ['tɛlɪ,mɛdɪsɪn]n. （通过遥测、电视、电话等方式求诊的）远距离医学30, smart factory 智慧工厂31, toolbox ['tu:l,bɔks]n. 工具箱32, intelligent manufacturing 智能制造33, error allocation 误差分配34, drilling force 钻削力35, convolutional networks 卷积网络36, architecture ['ɑrkə'tɛktʃɚ]体系架构37, efficiency [ɪ'fɪʃ(ə)nsɪ]n. 效率；效能；功效38, photoexcited [photoexcited]adj. 光激的39, Graphene nanosheets石墨烯纳米薄膜40, electron cyclotron resonance plasma微波电子回旋共振等离子体41, resonance ['rez(ə)nəns]n. [力] 共振；共鸣；反响42, cyclotron ['saɪklətrɒn]n. [核] 回旋加速器，粒子回旋加速器43, p-silicon P型硅44, Photoelectric behavior 光电效应45, evaluate [ɪ'væljʊeɪt]vt. 评价；估价；求…的值46, gait [geɪt]n. 步法，步态47, joint [dʒɒɪnt]n. 关节；接缝；接合处，接合点48, nanostructured materials纳米结构材料49, adhesive force [adhesive+force]粘合力，[力] 附着力50, surface roughness[机][气象] 表面粗糙度；表面光洁度51, Raman spectral analysis 拉曼光谱分析52, covalent bond [covalent+bond]n. [物化] 共价键53, Physical Etching 物理蚀刻54, threshold voltage [threshold+voltage] [电子] 阈值电压；[电子] 阈电压55, film deposition 薄膜沉积56, plasma ['plæzmə]n. [等离子] 等离子体57, electron cyclotron resonance[物] 电子回旋共振58, excitation [,eksaɪ'teɪʃ(ə)n]n. 激发，刺激；激励；激动59, etching ['etʃɪŋ]v. 蚀刻；刻画（etch的ing形式）60, acceptable [ək'septəb(ə)l]adj. 可接受的；合意的；可忍受的61, mean burr thickness 平均毛刺厚度62, delamination [diː,læmɪ'neɪʃən]n. 分层；[生物][化学] 层离63, finite element analysis[数] 有限元分析64, stress [strɛs]n. 压力；65, feed rate [feed+rate][机] 进给速率66, surface quality表面质量；表面符号；外观要求67, printed circuit board 印刷电路板68, Micro-Drilling 微孔钻削69, hole quality 成孔质量70, characteristics [,kærəktə'rɪstɪks]n. 特性，特征；特色（characteristic的复数）；特质71, analytical simulation 分析仿真72, application [ˌæplɪ'keɪʃ(ə)n]n. 应用；申请；应用程序；敷用73, layer [ˈler]n. 层，层次；膜；74, spin magnetic moment 自旋磁矩75, antiferromagnetic[,æntɪ,ferəʊmæg'netɪk]adj.反铁磁性的76, ferromagnetic [,ferə(ʊ)mæg'netɪk] adj. [物] 铁磁的；铁磁体77, structure ['strʌktʃə]n. 结构；构造78, carbon film 碳膜79, nanocrystallites 纳米微晶80, magnetoresistancen. [电磁] 磁阻；[物] 磁致电阻81, image feature 影像特征82, calculate ['kælkjʊleɪt]vt. 计算；预测；认为；打算83, detection algorithm 检测算法84, depth map 深度图85, machine vision[计] 机器视觉；计算机视觉86, technical risk 技术风险87, minimize [ˈmɪnɪˌmaɪz]vi. 最小化88, flycutting快速切削（flycut的现在分词形式）89, dynamic accuracy design动态精度设计90, frequency domain[计] 频域；[电子][通信] 频率范围91, workpiece [workpiece]n. 工件；轧件；工件壁厚92, Ultra-precision machine tool超精密机床93, mathematical model 数学模型94, range of motion 活动范围95, mechanical design 机械设计96, robot-assisted 机器人辅助的97, rehabilitation robot 康复机器人98, kinematic [,kɪnə'mætɪk]adj. [力] 运动学上的，[力] 运动学的99, dynamic simulation [计] 动态仿真100, diameter [daɪ'æmɪtə]n. 直径101, specificity [,spesɪ'fɪsətɪ]n. [免疫] 特异性;特征;专一性102, emulate ['emjʊleɪt]n. 仿真;仿效103, coining ['kɒɪnɪŋ]vt. 冲制;压模(coin的ing形式)104, polymer ['pɒlɪmə]n. 聚合物105, module ['mɒdjul]n. 模块;组件;模数106, filler ['fɪlə]n. 装填物107, resin ['rezɪn]n. 树脂;松香108, deformation n. 变形109, autonomous [ɔː'tɒnəməs]adj. 自治的;自主的;自发的110, metallic [mɪ'tælɪk]adj. 金属的,含金属的111, ceramic [sɪ'ræmɪk]adj. 陶瓷的;陶器的;制陶艺术的n. 陶瓷;陶瓷制品112, interaction [ɪntər'ækʃ(ə)n]n.相互作用；[数] 交互作用n.互动113, payload ['peɪləʊd]n.有效载荷，有效负荷；114, magnetic [mæg'netɪk]adj.地磁的；有磁性的；有吸引力的115, ion ['aɪən]n.[化学] 离子116, irradiation [ɪ,reɪdɪ'eɪʃ(ə)n]n.照射；发光，放射。
机械专业英语常见单词
1、mold n. 模具v.铸造(第一单元)2、die 钢模冲模3、term 术语4、tooling 工艺装备5、plastic parts 塑料件6、hardened steel 硬质刚7、aluminium 铝8、beryllium-copper alloy 铍铜合金9、steel molds 钢模10、Rockwell-C scale 洛氏硬度11、resin 树脂12、sprue喷嘴13、runner 流道14、gate 浇口15、protrusion 突出物,凸模16、core 型芯17、clay 粘土18、pin 销钉19、plenum 高压20、vent 通风口21、overhang v. 悬挂22、household 家庭的23、bucket n.桶24、cling to 黏附25、stripper plate 分馏柱塔板26、thermoplastics 热塑性材料27、solidification n.凝固28、chase vt.雕镂29、slide n. 滑块30、perpendicular 垂直的31、gib n.楔形块32、horn pin 推杆33、tire 轮胎34、lander 接触的35、hose 管道36、forklift 叉式升降机37、overhead crane 桥式起重机38、hoist n.提升39、impressions 压痕,型腔40、cavitation第二单元1、Injection Monding 注射模2、gravity 重力3、hopper 料斗4、barrel n.桶5、screw 螺杆,螺孔6、plunger 活塞7、chamber 腔8、melt v.熔化9、nozzle 喷嘴10、cravity 型腔11、gate 浇口12、runner system 热流道系统13、solidify v.使凝固14、ejector pin 顶针15、calmp 夹钳16、tonnage 吨位17、molten 熔铸的18、sprue bushing 浇口套19、mold cavity 模具型腔20、thickness 厚度21、plastication n.塑化22、throat 颈部,窄处23、non-return valve 单向阀24、extruder n.挤压25、plunder 活塞26、melt pool 榕料池27、vacuum 真空28、hydraulics 液压的29、water-cooling 水冷30、resin 树脂31、pellet 小球32、granule 颗粒33、poured into 流入,涌入34、screw flight 螺杆上的螺纹。
机械类专业英语单词
⏹Unit1⏹lubricant：n.润滑剂⏹graphite ：n.石墨⏹polymer ：n.聚合材料，聚合体⏹cobalt：n. Co. 钴⏹foil n.箔，金属薄片⏹beverage can n.饮料罐⏹maganesium ：n. Mg[化]镁⏹amorphous n.非晶体⏹chromium ：n. Cr.铬⏹nick n.刻痕、缺口⏹dent n.凹、凹痕⏹valence n.（化合）价、原子价⏹photon n. [物]光子⏹piezoelectric n.压电晶体⏹superconductor n.超导体⏹sintering v.烧结⏹refractive index 折射率⏹degradation n.降级, 降格, 退化⏹modulus n.系数, 模数⏹covalent adj.[化]共有原子价的,共价的⏹covalent bond 共价键⏹matrix n.矩阵、基体⏹thermoset polymer 热固塑料⏹permeability n.渗透性⏹polyisobutylene n.[化]聚异丁烯⏹elastomeric adj.弹性体的⏹crystallinity n.结晶性、结晶度⏹molecular weight 分子量⏹hydrophilic adj.亲水的⏹hydrophobic adj.恐水的⏹die ：n.模具⏹stress-strain 应力-应变⏹yield point：屈服点⏹tensile strength ：抗拉强度⏹chlorine：n. cl，氯⏹nitrogen ：n. N, 氮⏹be prone to ：易于，有…的倾向⏹anodic：adj. 阳极的⏹cathodic ：adj. 阴极的⏹polyester ：n.聚酯⏹gasket：n.垫圈、衬垫⏹bronze ：n.青铜⏹nickel silver ：n.镍黄铜⏹coefficient of thermalconductivity：导热系数⏹coefficient of linearexpansion ：线性热胀系数⏹thermostat：n.恒温器⏹resistivity ：n.抵抗力、电阻系数⏹dielectric strength：绝缘强度⏹ferromagnetic ：adj. 铁磁的、铁磁体⏹transmittance ：n. 透射⏹reflectance ：n. 反射比、反射系数⏹aluminum：n. Al. 铝⏹molybdenum：n.钼⏹tungsten ：n.钨⏹silicon ：n.硅⏹vanadium ：n.钒⏹eutecoid ：a.共析的⏹hypoeutectoid: a.亚共析的⏹hypereutectoid: a.过共析的⏹proeutectoid: a.先共析的⏹cementite ：n.渗碳体⏹ferrite ：n.铁素体Unit2 Heat Treatment of Matals⏹Centigrade degree ：℃摄氏温度⏹Fahrenheit degree：℉华氏温度⏹etch v.蚀刻⏹nitric acid 硝酸⏹pearlite n.珠光体⏹microscopic examination 金相试验⏹hardening：v.淬火⏹hardenability ：n.淬透性⏹quench：v.淬火⏹tempering ：v.回火⏹martensite：n.马氏体⏹precipitation：n. 沉淀（物），析出（物）⏹agglomeration ：n.凝聚、结块⏹coalescence ：n. 聚集、合并⏹salt bath：盐浴⏹austemper：n. A（奥氏体）回火⏹martemper n. M（马氏体）回火⏹nitriding 渗氮⏹crystalline a.n.结晶的（体），晶体的⏹normalizing 正火⏹spheroidizing 球化处理⏹carburizing 渗碳⏹case hardening：表面硬化⏹carbonaceous ：a.碳的，含碳的⏹charcoal n. 木炭⏹coke n.焦碳⏹carbonitriding：v. 碳氮共渗、氰化⏹ammonia n.氨水⏹cyaniding v.氰化⏹sodium cyanide 氰化钠⏹nitriding v.渗氮⏹Brinell n.布氏硬度⏹alkalie n.碱⏹crude oil：原油Unit3 Casting Processes⏹pour v.浇注⏹inject v. 注射、注入⏹mold n.模子,铸型⏹Cavity n. 型腔⏹bronze n. 青铜⏹brass n.黄铜⏹sprue n.浇注口、直浇道⏹runner n.横浇道⏹void n.空隙、缩孔⏹Shink n.收缩⏹flask n.长颈瓶, 烧瓶，砂箱⏹cope n.上箱⏹drag n.下箱⏹core print 型芯座、型芯头⏹gating system 浇注系统⏹Parting line 分型线、接合线⏹draft n. 拔模斜度⏹pouring cup 浇口盆⏹vent n.通风孔、排气孔⏹allowance n.余量、公差⏹bonded sand 粘砂⏹bentonite n.斑脱土、膨润土⏹mull vt.研磨⏹compaction n.压紧、紧实⏹alignment pin 定位销⏹concave a. n. 凹的、凹面⏹chill n. 激冷铸型、金属冷铸模、冷铁⏹bake v.烘焙、干燥⏹mate v. 配合、紧密结合⏹crucible n.坩埚⏹degas v. 脱气、排气⏹backflow v.回流⏹dendrite n.树枝状结晶⏹homogenous a.均质的⏹eutectic a.共晶的⏹vibrating table振动台⏹sand/shot blaster喷丸清理机⏹Ｏxide n.氧化物⏹investment casting熔模铸造⏹lost wax casting 熔模铸造、失蜡铸造⏹pharaoh n.法老王（古埃及君主的称号）、暴君⏹intricate a.复杂的、精致的⏹turbine blade涡轮叶片⏹refractory a.难溶的、耐火的⏹refractory slurry 耐火涂料⏹robust a.坚固的、耐用的⏹oven n.炉子、烤箱、加热室⏹undercut n.下陷、凹部⏹mold permeability 充型能力⏹stellite n.钨铬钴合金、硬合金⏹hastelloyｎ．镍基合金⏹close tolerance紧公差⏹centrifugal casting离心浇铸（注）法⏹inclusion n.夹杂物⏹surface finish表面精度⏹OD:outer diameter 外径⏹ID: inner diameter内径⏹boiler n.锅炉⏹flywheel n.调速轮⏹cylinder liner气缸套⏹axis-symmetric a.轴对称的⏹expendable a.一次使用的、消耗性的Unit４Forging Processes⏹item n.产品、零件⏹hammer blow锤打、锤击⏹power hammer动力锤⏹anvilｎ．铁砧、砧座⏹semi-mechanized a.半机械化的⏹forging press 锻压机⏹quantity production 大量生产⏹open-die forging开模锻造⏹hammer forging锤锻⏹forging hammer 锻锤⏹closed-die forging闭模锻造⏹lateral a.横向的⏹upsetting n.钝锻、镦粗⏹die n.锻模⏹ram n.压头、顶杆⏹surface finish 表面光洁度⏹jet-aircraft 喷气式飞机（发动机）⏹hydraulic a.液压的、水压的⏹marine propeller 船用螺旋桨⏹shaft n.轴⏹drop-forge 落锤锻造、落锻⏹ingot n.钢锭、锭块⏹manipulaton n.操作、处理⏹crystal n.晶体、晶粒⏹finishing operation 最后（完成）工序⏹plating n.电镀⏹frame member 构件⏹recrystallization n.再结晶⏹forge hot 热锻⏹forge cold 冷锻⏹blacksmith n.锻工、铁工⏹impression die forging 模锻⏹die forging 模锻⏹die impression 刻印模、槽模⏹forging die 锻模⏹principal stress 主应力⏹press forging 压锻⏹upset forging 顶锻（镦粗）⏹bolt n.螺钉⏹fastener n.紧固件⏹roll forging 滚锻⏹leaf spring 板簧、片簧⏹swaging 型锻、模锻⏹net shape forging 净形锻造⏹blank 毛坯、坯体⏹tooling v. 加工⏹capital expenditure 基本建设费用、资本支出⏹thrust force 推力⏹rib n.肋板⏹shift n.移动、变化⏹round off 修整⏹lateral a.横向的、侧面的⏹stress-raiser 应力集中源⏹match v. n.配合、装配⏹powder metallurgy 粉末冶金⏹sintering v.烧结⏹compact v.压紧、塞满n.压制品、压块⏹coalesce n.熔合⏹compaction n.压紧⏹ferrous a.铁的、含铁的⏹nonferrous a.不含铁的、非铁的⏹ferrous metal 黑色（铁类）金属⏹nonferrous metal 有色金属⏹controlled atmosphere furnace保护气体炉、可控气氛炉Unit5 Powder Metallurgy⏹structural components 构件、结构零件⏹homogeneous a. 均匀的、相似的⏹compromise n. v.折衷、妥协⏹segregate v.隔离⏹dusting n.清扫、除尘⏹consolidation n. 压实、凝固、加强⏹elevated a.升高的、提高的⏹Whilst conj.时时、同时⏹bush n.轴瓦、衬套、轴套⏹bearing n.轴承⏹uniaxial a. 单轴的⏹atomize v.打碎、使成微粒、使雾化⏹elemental a.基本的、元素的、单体的⏹lithium n.[化]锂⏹stearate n.[化]硬脂酸盐⏹of say 比方说、大约、估计、假定⏹isostatic a.均衡的、等压的⏹membrane n.膜、隔膜⏹billet n.坯段⏹rectification n.校正、调整、清除⏹encapsulate v.封装、压缩⏹evacuate v.抽空、排空、搬空⏹contamination n.污染、污染物⏹densification n.压实、密封、稠化⏹yield strength 屈服强度⏹enclosure n.围住、盒子、外壳⏹metal injection moulding 金属注塑（射）成型⏹screw thread 螺纹⏹moulded plastic 模压塑料⏹skeleton n.骨骼、骨干、基体⏹impregnate v.注入、灌注、浸透⏹infiltrate v.渗透⏹cemented a.渗碳的、烧结的⏹thermoplastics n.热塑性塑料⏹thermosetting plastic 热固性塑料⏹elastomer n.人造橡胶⏹reciprocating a.往复的、来回的、摆动的⏹extruder n.压出机、挤压机⏹resin n.树脂v.涂树脂于⏹granule n.颗粒、细粒⏹eject v.驱逐、逐出、喷射⏹plunger n.活塞⏹stuffing n.填充物、填塞料⏹patent v.取得…的专利n.专利⏹celluloid n.赛璐珞、明胶Unit6 Injection Moulding⏹thermoplastics n.热塑性塑料⏹thermosetting plastic 热固性塑料⏹elastomer n.人造橡胶⏹reciprocating a.往复的、来回的、摆动的⏹extruder n.压出机、挤压机⏹resin n.树脂v.涂树脂于⏹granule n.颗粒、细粒⏹eject v.驱逐、逐出、喷射⏹plunger n.活塞⏹stuffing n.填充物、填塞料⏹patent v.取得…的专利n.专利⏹celluloid n.赛璐珞、明胶⏹encyclopedia n.百科全书⏹HDPE——high densitypolyethylene 高密度聚乙烯⏹rheology n.流变学、流变能力⏹margin n.利润⏹skimpy a.不足的、吝啬的⏹mat n.垫子、席子⏹analogy n.模拟、类似⏹fluidity n.流动性⏹entity n.实体⏹crystalline n.晶体⏹amorphous n.非晶体⏹solvent a.溶解的n.溶剂⏹polycarbonate n.[化]聚碳酸酯⏹opaque a.不透明的、不传热的⏹transparent a.透明的⏹chop v.剁碎、砍n.砍、排骨⏹clamp n.夹子、夹具v.夹紧⏹viscous a.粘性的、粘滞的⏹spine n.脊柱、中心⏹knockout n.脱模、脱壳、脱模机⏹bin n.容器、箱子⏹viscosity n.粘滞、粘性⏹orientation n.取向、方向、定位⏹shear thinning 剪切变稀，使界层内剪力变小⏹crystallinity n.结晶度、结晶性⏹overpack n.第二层包装⏹inhibit v. 抑制、约束⏹susceptibility (to) n.敏感性、灵敏度⏹stress crack 应力裂纹⏹transverse a.横向的、横断的⏹superimpose v.添加、双重、叠加、安装、配合⏹superimpose a.成阶层的、有层理的⏹biaxial a.二轴的⏹obstruction n.阻塞、妨碍、障碍物⏹molecular weight 分子量⏹process variable 工艺参数⏹tensile strength 抗拉强度⏹conveyor n.输送机、传送带⏹flash n. 余料、(模塑)溢料、（模锻）飞边、毛边⏹foam n.泡沫塑料⏹reground a.重新研磨的⏹elaborate a.精细的、精心制作的⏹hydraulics n.水力学⏹in attendance 负责、值班⏹warpage n.翘曲、扭曲、热变形⏹render v.致使、给予⏹cross-disciplinary 交叉学科的⏹lead time 订货至交货的时间⏹debugging n.调试Unit7 METAL CUTTING⏹machine tool 机床⏹rake angle (刀具)前角⏹rake face 前刀面⏹tip n.顶、尖端、末端⏹normal a.正交的、垂直的⏹dissipation n.消散、分散⏹mild steel 软钢、低碳钢⏹clearance angle 后角⏹flank face 后刀面⏹rub v.擦、摩擦⏹spoil v.损坏、破坏⏹feed rate 进给量⏹chip n.切屑、碎片⏹schematically adv.图解地、图示地⏹shear zone 剪切区域⏹yielding n.屈服、变形⏹chip curl 切屑螺旋、螺旋形切屑⏹strain n.应变、张力v.拉紧、扯紧⏹slip plane 滑移面、滑动面⏹categorise v.分类⏹BUE-built up edge 积屑瘤⏹shear strength 抗剪强度⏹dislodge v.驱逐、移走⏹planar a.平面的、平坦的⏹vector n.矢量⏹cater v.满足、迎合⏹fluctuation n.波动、起伏⏹coefficient n.系数⏹dissipate v.驱散、消散⏹geometry n.几何学⏹turning n.车削⏹nose radius 刀尖半径⏹surface geometry 表面几何图形⏹rigidity n.刚性、硬度⏹vibration n.振动⏹exert v.施加⏹equation n.方程式、等式、公式⏹erroneously adv.错误地、不正确地⏹coolant n.冷却液、冷却剂⏹investigation n.调查、研究⏹asperity n.微粒、凹凸不平⏹capillary n.毛细管 a.毛细作用的Unit8 Grinding⏹abrasive wheel 砂轮、磨轮⏹miniature a.缩小的、微型的⏹cutting edge 切削刃、刃口、刀刃⏹finishing process 精加工、最后的工序⏹cylindrical grinding machine外圆磨床⏹surface grinding 平面磨削⏹planer 刨工、刨机⏹reciprocating adj.往复的、来回的⏹planer-type reciprocating table刨床式往复工作台⏹periphery n.外围⏹fixture n.工作夹具⏹strap n.带、皮带，v.用带捆扎⏹strap clamp 带夹⏹clamping strap 夹板、压板⏹depth of cut 切削深度、背吃刀量⏹plunge-cut 切入式（横向进给）磨削⏹internal grinding 内圆磨削⏹planetary internal grinding 行星内圆磨削⏹rest blade 托板⏹cross feed 横向进给⏹longitudinal feed 轴向（纵向）进给⏹peripheral velocity 圆周速度⏹spin v. n. 旋转⏹centerless grinding 无心磨削⏹clog n. v.障碍、阻塞⏹recessed wheel 槽式轮⏹slotting 开槽、打孔⏹straight cup wheel 直角碗形砂轮⏹flaring cup 杯形(碗形)砂轮⏹emery n.金刚砂⏹corundum n.刚玉、金刚砂⏹carborundum n.碳化硅、金刚砂⏹silicate n.硅酸盐⏹resinoid n.树脂⏹shellac n.虫漆、虫胶⏹oxychloride n.氯氧化物Unit9 Lapping and Polishing⏹lap n.研磨盘、研具⏹close fit 紧配合、过盈配合⏹piston n.活塞⏹cylinder n.气缸、圆筒⏹plateau n.高地、高原⏹mountain range 山脉⏹grind down 磨平、碾碎⏹electropolishing 电解抛光⏹ion n.离子⏹electrolysis n.电解⏹electrolyte n.电解、电解液⏹film n.薄膜、膜层v.在…上覆以薄膜⏹dissolution n.分解、解散⏹depression n.凹陷处、坑、洞、低气压⏹projection n.凸出物⏹anodic a.阳极的⏹cathodic a.阴极的⏹stock n.原料、材料⏹chemical mechanical polishing化学机械抛光⏹integrated circuit 集成电路⏹wafer n.晶片、圆片⏹resilient a.弹回的、有回弹力的⏹pad n.垫、衬垫⏹reagent n.试剂、反应物⏹oxidation-reductive reaction氧化还原反应⏹desorption n.解吸附作用Unit10 Surface Engineering⏹tailor…to 适应（满足）…的要求⏹covering the surface 表面涂覆⏹resistivity n.电阻率⏹conversion coating 转化膜⏹thermal spraying 热喷涂⏹hot dipping 热浸、热镀⏹deposit v.沉淀、涂、喷镀⏹substrate n.基体、衬底⏹ionic a.离子的⏹nugget n.天然金块、矿块⏹ripple n.波纹，起波纹⏹replenishment n.补给、补充⏹potential n.潜能、电压 a.势的、位的⏹gun n.喷射器⏹PVD—Physical VaporDeposition 物理气相沉积⏹CVD—chemical VaporDeposition 物理气相沉积⏹conical a.圆锥的、圆锥形的⏹thermal evaporation 热蒸发（镀膜）⏹fragile a.易碎的、脆的⏹line of sight 视线、瞄准线⏹jet engineer n.喷气发动机⏹sputtering n.阴极真空喷镀、阴极溅镀⏹donor n.原料物质、杂质⏹atomise v.使分裂为原子，将…喷成雾状⏹radio-frequency sputtering 射频溅射⏹titanium nitride 氮化钛⏹volatilize v.挥发⏹decompose v.分解、使腐烂⏹nickel carbonyl 羰基镍⏹altering the surface 表面改性⏹electron beam treatment 离子束表面改性⏹ion implantation 离子注入⏹impinge v.撞击⏹coil n.线圈⏹lattice n.晶格⏹vacuum chamber 真空室、压力室⏹laser beam treatment 激光表面改性⏹dosage n.剂量、用量Unit11 Lathe and Turning⏹turning v.车削⏹lathe n.车床⏹engine lathe 普通车床⏹toolroom lathe 多轴车床⏹turret lathes 六角转塔式车床⏹vertical turning and boring mill旋转立式车床⏹grey cast iron 灰口铸铁⏹nodular cast iron 球墨铸铁⏹damp v.阻尼、衰减、抑止⏹headstock n.主轴箱⏹spindle n.主轴⏹carriage n.车架、床鞍⏹gearbox n. 变速箱⏹tool post 刀架、刀座⏹compound rest 复式刀架、（车床）小刀架⏹carriage （车床的）托板、溜板⏹tailstock n.尾架⏹quill n.主轴、套筒轴⏹tailstock quill 尾架顶尖套筒轴⏹face plate 划线平台、划线平板⏹nut n.螺母⏹guideway 导轨、导槽⏹twist drill 麻花钻⏹apron n.溜板箱⏹nose radii 刀尖半径⏹shank n.刀柄、刀把⏹lead screw 丝杠⏹feed rod 进给杆、光杆⏹HSS—high speed steel 高速钢⏹braze v.铜焊、钎焊⏹worm gear 涡轮⏹annular grooves 环形槽⏹trapezoidal adj.梯形的⏹thread form 牙形⏹clamp n.夹具、夹钳，v.夹紧⏹washer n. 垫圈⏹ribbon n.带子⏹cemented carbide 硬质合金、烧结碳化物⏹chip breaker 碎屑装置⏹seat n.刀座⏹contouring 仿形加工⏹helix n.螺旋、螺旋状物⏹pitch n.螺距⏹cross slide 横向拖板⏹shoulder n.轴肩⏹periphery n.外围⏹spiral n.螺旋 a.螺旋形的⏹crank v.转动曲柄⏹chuck n.卡盘v.用卡盘夹⏹apex n.顶点⏹stroke n.行程⏹disengagement n.脱离⏹kinematic adj.运动学的⏹gear train 轮系⏹knurling 滚花⏹file n.锉刀v.锉⏹guidelines n.指导方针⏹HSS:high-speed-steel 高速钢Unit12 Drilling and Milling⏹drilling n.钻孔、钻削⏹milling n.铣削⏹hand drill 手钻⏹drilling machine 钻床⏹flute n.凹槽⏹coolant n.冷却液⏹Shank n.手柄、柄部⏹wedge action 楔紧作用⏹socket n.孔、牙槽⏹tang n.扁尾、柄脚、刀柄⏹slot n.缝、狭槽，v.开槽于⏹chisel-like n.凿子，v.砍凿⏹chisel-like edge 横刃⏹twist drill 麻花钻⏹margin n.边缘、边界、空白⏹core drill 空心钻⏹conduit n.管道、导管⏹gun drill 深孔钻、枪孔钻⏹trepanning 开孔、打孔、钻眼⏹spade drill 扁钻⏹tangible adj.切实的⏹boring n.钻孔、镗孔⏹milling cutter 铣刀⏹helical a.螺旋状的⏹rake angle 前角、刀面角⏹relief angle 后角⏹versatile adj.通用的、万能的⏹up milling 逆铣⏹down milling 顺铣⏹backlash eliminator 齿隙消除器⏹horizontal milling machine卧式铣床⏹vertical milling machine 立式铣床⏹arbor n.轴、心轴⏹slitting saw 切割锯，开槽锯⏹spline n.花键、键槽，v.开键槽⏹dovetail groove 燕尾槽⏹rachet wheel 棘轮⏹gear hob 齿轮滚刀、滚齿刀⏹convex adj.凸起的⏹concave adj. 凹入的，n.凹、凹面⏹sintered carbide 烧结碳化物、硬质合金⏹heavy cuts 重切削、强力切削Unit13 JIGS AND FIXTURES⏹jigs n.钻模、夹具⏹fixture n.夹具⏹rib n.肋板⏹reamer n.绞刀⏹interchangeable a.可互换的⏹spare part n.备件⏹clearance n.间隙、距离⏹observance n.习惯、惯例⏹encroach v.侵占、超出界限⏹mutually adv.互相地、互助⏹translation n.平移⏹tap v.攻螺纹⏹bushing n.轴套、衬套⏹flange n.凸缘、法兰v.给…装凸缘⏹post n.杆、柱⏹drill plate 钻模⏹tenon n. [木工] 榫，凸榫，v. 造榫，榫接Unit14 LIMITS AND TOLERANCES⏹limit n.极限⏹tolerance n.公差⏹assembly drawing 装配图⏹detail drawing 零件图、详图⏹conversant adj.熟悉的、精通的⏹trigonometric adj.三角法的⏹unilateral adj.单边的⏹bilateral adj.双边的⏹interchangeability n.互换性⏹component part 零件、部件⏹individual part 单个零件⏹mating parts 配合件⏹tolerance zone 公差带⏹interference n.干涉、过盈⏹blanket note 注释⏹allowance n.允差⏹nominal size 名义尺寸、基本尺寸⏹force fit 压入配合⏹imperfection n.不完整性、非理想性⏹clearance fit 间隙配合⏹transition fit 过渡配合⏹interference fit 过盈配合⏹shaft-basis system 基轴制⏹hole-basis system 基孔制⏹horology n.钟表学Unit15 Unconventional Machining Processes(Ⅰ)⏹ultrasonic machining 超声波加工⏹electron-beam machining 电子束加工⏹plasma-jet machining 等离子喷射加工⏹etch v.蚀刻⏹electric current 电流⏹discharge n. v.放电⏹EDM：electro-dischargemachining 电火花加工⏹erode v.腐蚀、侵蚀⏹dielectric n.电介质，绝缘体，adj.非传导性的⏹reservoir n.水库、蓄水池⏹foul adj.淤塞的、肮脏的⏹debris n.碎片，残骸⏹capacitor n.电容器⏹servomechanism n. 伺服机构(系统), 自动控制装置⏹erode vt.侵蚀，腐蚀，vi.受腐蚀⏹ECM：electrochemicalmachining 电化学加工⏹electrolytic adj.电解的，由电解产生的⏹electrolyte n.电解、电解液⏹profiling n.压型、仿形加工⏹chloride n.[化]氯化物⏹chloride sodium n.[化]氯化钠⏹nitrate n.[化]硝酸盐、硝酸钾⏹sodium nitrate n.[化]硝酸钠⏹turbine blade 涡轮叶片⏹jet-engine n.喷气发动机⏹forging-die 锻模⏹die sinking 加工模腔、开模、制阴模⏹burr n.毛口、毛头v.去毛刺、磨光毛口⏹deburring n.修边、去除毛刺、倒角⏹oscillation n.振动⏹transducer n.变频器、换能器、传感器⏹amplitude n.振幅⏹of the order of 达到…的数量或程序⏹oscillate v.振动、振荡⏹concentration n.浓度⏹crater n.弹坑Unit16 Unconventional Machining Processes(Ⅱ)⏹laser beam machining 激光加工⏹coherent light beam 相干光束⏹amplification n.放大、扩大⏹stimulated emission 受激发射⏹coherency n.相干性⏹diverging angle 发散角⏹mrad:millirad (辐射吸收剂量单位)毫拉德⏹divergence n.发散性⏹bleeder hole 排气孔⏹fuel pump 燃油泵⏹hub n.轮毂、轴套⏹vane (螺旋浆等的)翼、叶片⏹flash lamp 闪光灯、光泵⏹focal length 焦距⏹tribological a.摩擦学的⏹punch n.冲压机、冲床v.冲孔⏹stylus n.铁笔⏹scroll roll 卷辊⏹stamping n. v.冲压⏹engraving n.雕刻术、雕版⏹vacuum chamber 真空室、压力室⏹kerf n.切口、截口⏹water-jet machining 水喷射加工⏹momentum n.动力、动量、冲量⏹gas turbine 燃气涡轮⏹hydrodynamic a.水利的、水压的⏹deburring n.修边、去毛刺⏹saw n.锯⏹jet-nozzle 喷嘴、喷射管⏹vinyl n.乙基烯、乙烯树脂⏹foam n.泡沫、泡沫塑料⏹dashboard n.仪表板、挡泥板⏹abrasive water-jet machining磨料喷射加工⏹ruby n.红宝石⏹sapphire n.蓝宝石、刚玉、青玉⏹photochemical machining 光化学加工⏹photoetching 光刻⏹photoresist n.感光树脂、光刻胶、光致抗蚀剂⏹etching n.蚀刻、蚀刻法⏹photo-tool 光刻掩模⏹film n.薄膜、胶片、膜层⏹developer n.显影、显影剂⏹irradiate v.照射⏹actinic a.光化的、光化学的⏹ultraviolet a.紫外线的、紫外的n.紫外线辐射⏹ultraviolet light 紫外线⏹laminate v.碾压、把…压成薄片⏹negative-working photoresist负性感光胶⏹emulsion n.感光乳剂⏹stencil n.模版、蜡纸⏹aperture n.孔、穴、缝隙⏹hydrochloric a.盐酸的⏹alphanumeric a.文字数字的。
机械英语单词
board n.板卡fine adj.精密的word n.字ABS(absolute) adj.绝对的absolute adj.绝对的AC n.交流accelerate v.加速acceleration n.加速度active adj.有效的adapter n.适配器，插头address n.地址adjust v.调整adjustment n.调整advance v.前进advanced adj.高级的，增强的alarm n.报警ALM(alarm) n.报警alter v.修改amplifier n.放大器angle n.角度APC n.绝对式脉冲编码器appendix n.附录，附属品arc n.圆弧argument n.字段，自变量arithmetic n.算术arrow n.箭头AUTO n.自动automatic adj.自动的automation n.自动auxiliary function 辅助功能axes n.轴（复数）axis n.轴background n.背景，后台backlash n.间隙backspace v.退格backup v.备份bar n.栏，条battery n.电池baudrate n.波特率bearing n.轴承binary adj..二进制的bit n.位blank n.空格block n.块，段block n.撞块，程序段blown v.熔断bore v.镗boring n.镗box n.箱体，框bracket n.括号buffer n.v.缓冲bus n.总线button n.按钮cabient n.箱体calbe n.电缆calculate v.计算calculation n.计算call v.调用CAN(cancel) v.清除cancel v.清除canned cycle 固定循环capacity n.容量card n.板卡carriage n.床鞍，工作台cassette n.磁带cell n.电池CH(chanel) n.通道change v.变更，更换channel n.通道check v.检查chop v.錾削chopping n.錾削circle n.圆circuit n.电路，回路circular adj.圆弧的clamp v.夹紧clear v.清除clip v.剪切clip board n.剪贴板clock n.时钟clutch n.卡盘，离合器CMR n.命令增益CNC 计算机数字控制code n.代码coder n.编码器command n,v.命令communication n.通讯compensation n.补偿computer n.计算机condition n.条件configuration n.配置configure v.配置connect v.连接connection n.连接connector n.连接器console n.操作台constant n.常数，adj.恒定的contour n.轮廓control v.控制conversion n.转换cool v.冷却coolant n.冷却coordinate n.坐标copy v.拷贝corner n.转角correct v.改正，adj.正确的correction n.修改count v.计数counter n.计数器CPU n.中央处理单元CR n.回车cradle n.摇架create v.生成CRT n.真空射线管CSB n.中央服务板current n.电流，当前的，缺省的current loop n.电流环cursor n.光标custom n.用户cut v.切削cutter n.（元盘形）刀具cycle n.循环cylinder n.圆柱体cylindrical adj.圆柱的data n.数据（复数）date n.日期datum n.数据（单数）DC n.直流deceleration n.减速decimal point n.小数点decrease v.减少deep adj.深的define v.定义deg. n.度degree n.度DEL(delete) v.删除delay v,n.延时delete v.删除deletion n.删除description n.描述detect v.检查detection n.检查device n.装置DGN(diagnose) v.诊断DI n.数字输入DIAG(diagnosis) n.诊断diagnosis n.诊断diameter n.直径diamond n.金刚石digit n.数字dimension n.尺寸，（坐标系的）维DIR n.目录direction n.方向directory n.目录disconnect v.断开disconnection n.断开disk n.磁盘diskette n.磁盘display v,n.显示distance n.距离divide n,v除，v.划分DMR n.检测增益DNC 直接数据控制DO n.数字输出dog switch n.回参考点减速开关DOS n.磁盘操作系统DRAM n.动态随机存储器drawing n.画图dress v.修整dresser n.修整器drill v.钻孔drive v.驱动driver n.驱动器dry run 空运行duplicate v.复制duplication n.复制dwell n,v.延时edit v.编辑EDT(edit) v.编辑EIA n.美国电子工业协会标准electrical adj.电气的electronic adj.电子的emergency n.紧急情况enable v.使能encoder n.编码器end v,n.结束enter n.回车，v.输入，进入entry n.输入equal v.等于equipment n.设备erase v.擦除error n.误差，错误，故障esc=escape v.退出exact adj.精确的example n.例子exchange v.更换execute v.执行execution n.执行exit v.退出external adj.外部的failure n.故障FANUC n.（日本）法那克fault n.故障feed v.进给feedback v.反馈feedrate n.进给率figure n.数字file n.文件filt(filtrate) v.过滤filter n.过滤器fin(finish) n.完成（应答信号）fine adj.精密的fixture n.夹具FL （回参考点的）低速flash memory n.闪存flexible adj.柔性的floppy adj.软的foreground n.前景，前台format n.格式，v.格式化function n.功能gain n.增益GE FANUC GE法那克gear n.齿轮general adj.总的，通用的generator n.发生器geometry n.几何gradient n.倾斜度，梯度graph n.图形graphic adj.图形的grind v.磨削group n.组guidance n.指南，指导guide v.指导halt n,v.暂停，间断handle n.手动，手摇轮handy adj.便携的handy file 便携式编程器hardware n.硬件helical adj.螺旋上升的help n,v.帮助history n.历史HNDL(handle) n.手摇，手动hold v.保持hole n.孔horizontal a.水平的host n.主机hour n.小时hydraulic adj.液压的I/O n.输入/输出illegal adj.非法的inactive adj.无效的inch n.英寸increment n.增量incremental adj.增量的index 分度，索引initial adj.原始的initialization n.C523初始化initialize v.初始化input n.v.输入INS(insert) v.插入insert v.插入instruction n.说明interface n.接口internal adj.内部的interpolate v.插补interpolation n.插补interrupt v.中断interruption n.中断intervent n.间隔，间歇involute n.渐开线ISO n.国际标准化组织jog n.点动jump v.跳转key n.键keyboard n.键盘label n.标记，标号ladder diagram 梯形图language n.语言lathe n.车床LCD n.液晶显示least adj.最小的length n.长度LIB(library) n.库library n.库life n.寿命light n.灯limit n.极限limit switch n.限位开关line n.直线linear adj.线性的linear scale n.直线式传感器link n,v.连接list n,v.列表load n.负荷，v.装载local adj.本地的locate v.定位，插销location n.定位，插销lock v.锁定logic n.逻辑look ahead v.预，超前loop n.回路，环路LS n.限位开关LSI n.大规模集成电路machine n.机床，v.加工macro n.宏macro program n.宏程序magazine n.刀库magnet n.磁体，磁magnetic a.磁的main program n.主程序maintain v.维护maintenance n.维护MAN(manual) n.手动management n.管理manual n.手动master adj.主要的max adj.最大的，n.最大值maximum adj.最大的，n.最大值MDI n.手动数据输入meaning n.意义measurement n.测量memory n.存储器menu n.菜单message n.信息meter n.米metric adj.米制的mill n.铣床，v.铣削min adj.最小的,n.最小值minimum adj.最小的,n.最小值minus v.减,adj.负的minute n.分钟mirror image n.镜像miscellaneous function n.辅助功能MMC n.人机通讯单元modal adj.模态的modal G code n.模态G代码mode n.方式model n.型号modify v.修改module n.模块MON(monitor) v.监控monitor v.监控month n.月份motion n.运动motor n.电机mouse n.鼠标MOV(移动） v.移动move v.移动movement n.移动multiply v.乘N number n.程序段号N.M n.牛顿.米name n.名字NC n.数字控制NCK n.数字控制核心negative adj.负的nest v,n.嵌入，嵌套nop n.空操作NULL n.空number n.号码numeric adj.数字的O number n.程序号octal adj.八进制的OEM n.原始设备制造商OFF adv.断offset n.补偿，偏移量ON adv.通one shot G code 一次性G代码open v.打开operate v.操作operation n.操作OPRT(operation) n.操作origin n.起源，由来original adj.原始的output n,v.输出over travel 超程over voltage 过电压overcurrent 过电流overflow v,n.溢出overheat n.过热overload n.过负荷override n.（速度等的）倍率page n.页page down 下翻页page up 上翻页PARA(parameter) n.参数parabola n.抛物线parallel adj.平行的，并行的，并联的parameter n.参数parity n.奇偶性part n.工件，部分password n.口令，密码paste v.粘贴path n.路径pattern n.句型，式样PC n.个人电脑PCB n.印刷电路板per prep.每个percent n.百分数pitch n.节距，螺距plane n.平面PLC n.可编程序逻辑控制器plus n.增益，prep.加,adj.正的PMC n.可编程序逻辑控制器pneumatic adj.空气的polar adj.两极的，n.极线portable adj.便携的POS(position) v,n.位置，定位position v,n.位置，定位position loop n.位置环positive adj.正的power n.电源，能量，功率power source n.电源preload v.预负荷preset v.予置pressure n.压力preview v.予览PRGRM(program) v.编程，n.程序print v.打印printer n.打印机prior adj.优先的，基本的procedure n.步骤profile n.轮廓，剖面program v.编程，n.程序programmable adj.可编程的programmer n.编程器protect v.保护protocol n.协议PSW(password) n.密码，口令pulse n.脉冲pump n.泵punch v.穿孔puncher n.穿孔机push button n.按钮PWM n.脉宽调制query n.问题，疑问quit v.退出radius n.半径RAM n.随机存储器ramp n.斜坡ramp up v.（计算机系统）自举range n.范围rapid adj.快速的rate n.比率，速度ratio n.比值read v.读ready adj.有准备的ream v.铰加工reamer n.铰刀record v,n.记录REF(reference) n.参考reference n.参考reference point n.参考点register n.寄存器registration n.注册，登记relative adj.相对的relay v,n.中继remedy n.解决方法remote adj.远程的replace v.更换，代替reset v.复位restart v.重启动RET(return) v.返回return v.返回revolution n.转rewind v.卷绕rigid adj.刚性的RISC n.精简指令集计算机roll v.滚动roller n.滚轮ROM n.只读存储器rotate v.旋转rotation n.旋转rotor n.转子rough adj.粗糙的RPM n.转/分RSTR(restart) v.重启动run v.运行sample n.样本，示例save v.存储save as 另存为scale n.尺度，标度scaling n.缩放比例schedule n.时间表，清单screen n.屏幕screw n.丝杠，螺杆search v.搜索second n.秒segment n.字段select v.选择selection n.选择self-diagnostic 自诊断sensor n.传感器sequence n.顺序sequence number 顺序号series n.系列，adj.串行的series spindle n.数字主轴servo n.伺服set v.设置setting n.设置shaft n.轴shape n.形状shift v.移位SIEMENSE （德国）西门子公司sign n.符号，标记signal n.信号skip v,n.跳步slave adj.从属的SLC n.小型逻辑控制器slide n.滑台,v.滑动slot n.槽slow adj.慢soft key n.软键盘software n.软件space n.空格，空间SPC n.增量式脉冲编码器speed n.速度spindle n.主轴SRAM n.静态随机存储器SRH(search) v.搜索start v.启动statement n.语句stator n.定子status n.状态step n.步stop v.停止,n.挡铁store v.储存strobe n.选通stroke n.行程subprogram n.子程序sum n.总和surface n.表面SV(servo) n.伺服switch n.开关switch off v.关断switch on v.接通symbol n.符号，标记synchronous adj.同步的SYS(system) n.系统system n.系统tab n.制表键table n.表格tail n.尾座tandem adv.一前一后，串联tandem control n.纵排控制（加载预负荷的控制方式）tank n.箱体tap n,v.攻丝tape n.磁带，纸带。
机械双字分词 英文分词
机械双字分词英文分词好的，以下为您生成 20 个关于机械相关的双字分词示例，包含英文分词、英语释义、短语、单词、用法和双语例句：---1. 机械加工- 英文分词：Mechanical Processing- 英语释义：The act or process of modifying or fabricating a material or component using machinery and tools.- 短语：mechanical processing technology（机械加工技术）- 单词：processing（加工；处理）- 用法：“Mechanical processing is widely used in the manufacturing industry.”（机械加工在制造业中被广泛应用。
）- 双语例句：The quality of the product depends on the accuracy of mechanical processing.（产品的质量取决于机械加工的精度。
）2. 机械设计- 英文分词：Mechanical Design- 英语释义：The process of creating or planning the structure, form, and functionality of a mechanical system or device.- 短语：mechanical design engineer（机械设计工程师）- 单词：design（设计；构思）- 用法：“The mechanical design of this machine needs to be improved.”（这台机器的机械设计需要改进。
）- 双语例句：He is specialized in mechanical design and has many innovative ideas.（他专攻机械设计，有很多创新的想法。
机械工程专业英语翻译
机械工程专业英语翻译Introduction机械工程是一门涵盖机械原理、设计、制造以及维护的综合性学科，其中涉及许多专业术语和英语翻译。
良好的英语翻译能力对机械工程师在国际合作和成果交流中至关重要。
本文将介绍机械工程专业中常见的英语单词和短语，并提供中文翻译和相关注释。
Mechanical Principles 机械原理对于机械原理，下面是一些常见的英语单词和短语。
1.Mechanism（机构）：A mechanism is a device designedto transform input forces and movement into a desiredoutput force and movement.2.Kinematics（运动学）：Kinematics is the study ofmotion, without regard to the cause of the motion.3.Statics（静力学）：Statics is the study of thebehavior of structures, under the action of forceswithout producing motion.4.Dynamics（动力学）：Dynamics is the study of thebehavior of motion of objects under the action of forces.5.Thermodynamics（热力学）：Thermodynamics deals withthe relationships between heat, work, and energy.6.Fluid Mechanics（流体力学）：Fluid mechanics is thestudy of the behavior of fluids at rest or in motion. Mechanical Design 机械设计对于机械设计，下面是一些常见的英语单词和短语。
与机械有关英语单词
组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet柳丁table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver 气动起子worktable 工作桌OOBA（out of box audit）开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC(quality control)品管质量控制supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试V oltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP(standard operatingprocedures)制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resourcedepartment人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener 整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller??床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vicemanager副理section supervisor课长deputy section supervisor=vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, tohandle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down 抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=platepinch压板bolt螺栓name of a department部门名称administration/generalaffairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposedfingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a littlebigger尺寸偏大(小)cosmetic defect外观不良slippedscrewhead/slippery screwhead螺丝滑头slippedscrewhead/shipperyscrew thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal 金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansionprojects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products,up-to-grade products良品defective products, notup-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate;barricade隔板carton box纸箱to pull and stretch拉深to put material in place,to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution 转速manufacture management 制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to,switch---to throw--overswitching over切换engineering, projectdifficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing outpress冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock 库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinerybackto retrn of goods退货registration登记registration card登记卡to control管制to put forward and handin提报safe stock安全库存acceptance = receive验收to notice通知application form forpurchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary fordie engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die 冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plateblank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physicalinvetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference 会计部存查end-user/usingunit(department)使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application statusrecords of year-endphysical inventory Listandphysical inventory card年终盘点卡与清册使用－状况明细表blank and waste sheetNO.空白与作废单号plate电镀mold成型material for engineeringmold testing工程试模材料not included in physicalinventory不列入盘点sample样品incoming material to beinspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by/ prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected orreworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physicalinventory differenceanalysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/acceptedgoods/ acceptedparts/good parts良品defectiveproduct/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physicalinventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head 挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=diebutton圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block forlocation定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch =stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mm diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control品质管理人员FQC final qualitycontrol 终点品质管制人员IPQC in processquality control 制程中的品质管制人员OQC output qualitycontrol 最终出货品质管制人员IQC incoming qualitycontrol 进料品质管制人员TQC total qualitycontrol 全面质量管理POC passage qualitycontrol 段检人员QA quality assurance质量保证人员OQA output qualityassurance 出货质量保证人员QE quality engineering品质工程人员品质保证类FAI first articleinspection 新品首件检查FAA first articleassurance 首件确认TVR tool verificationreport 模具确认报告3B 3B 模具正式投产前确认CP capability index能力指数CPK capability indexof process 模具制程能力参数SSQA standardizedsupplier quality 合格供应商品质评估OOBA out of box audit开箱检查QFD quality functiondeployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average OutputQuality 平均出厂品质AOQL Average OutputQuality Level 平均出厂品质Q/R/SQuality/Reliability/Service 品质/可靠度服务MIL-STDMilitary-Standard 军用标准S I-S IV SpecialI-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept OnDeviation 特采UAI Use As It 首件检查报告FPIR First PieceInspection Report 百万分之一PPM Percent PerMillion 批号制程统计品管专类SPC Statistical ProcessControl 统计制程管制SQC Statistical QualityControl 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper CentralLimit 管制上限LCL Lower CentralLimit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeata bility 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do CheckAction 计划执行检查总结ZD Zero Defect 零缺点QI QualityImprovement 品质改善QP Quality Policy 目标方针TQM Total QualityManagement 全面品质管理MRB Material RejectBill 退货单LQL Limiting QualityLevel 最低品质水准RMA Return MaterialAudit 退料认可QAN QualityAmelionrate Notice 品质改善活动ADM AbsoluteDimension Measuremat全尺寸测量QT Quality Target 品质目标7QCTools 7 QualityControll Tools 品管七大手法通用之件类ECN EngineeringChange Notes 工程变更通知(供应商)ECO EngineeringChange Order 工程改动要求(客户)PCN Process ChangeNotice 工序改动通知PMP ProductManagement Plan 生产管制计划SIP Specification InProcess 制程检验规格SOP StandardOperation Procedure 制造作业规范IS InspectionSpecification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS InternationalWorkman Standard 工艺标准ISO InternationalStandard Organization国际标准化组织GS GeneralSpecification 一般规格CMCS C-ChinaM-Manufact C-CompaqS-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-QualityA-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-PaintingCompaq产品在龙华烤漆厂品管作业规范部类PMC Production &Material Control 生产和物料控制PPC Production PlanControl 生产计划控制MC Material Control物料控制ME ManafactureEngineering 制造工程部PE Project Engineering产品工程部A/C Accountant Dept会计部P/A Personal &Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research &Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order采购订单MO Manufacture Order生产单D/C Date Code 生产日期码ID/C IdentificationCode (供应商)识别码SWR Special WorkRequest 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM OriginalEquipment Manufacture原设备制造PCE PersonalComputer Enclosure 个人电脑外设PC Personal Computer个人电脑CPU CentralProcessing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North ofHongkong 中国大陆PRC People's Republicof China 中国大陆U.S.A the United Statesof America 美国A.S.A.P As Soon AsPossible 尽可能快的E-MAILElectrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-staticDischarge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM CompactDisk Read-Only Memory只读光碟FDD Floppy DiskDrive 软碟机HDD Hard Disk Drive碟碟机REF Reference 仅供参考CONN Connector 连接器CA V Cavity 模穴CAD Computer AidDesign 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit集成电路T/P True Position 真位度TYP Type 类型WDR Weekly DeliveryRequitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcatio n,Consumer electronic's 消费性电子5WIHWhen,Where,Who,What, Why,How to5MMan,Machine,Material,M ethod,Measurement4MIHMan,Materia,Money,Met hod,Time 人力,物力,财务,技术,时间(资源)SQA Strategy QualityAssurance 策略品质保证DQA Desigh QualityAssurance 设计品质保证MQA ManufactureQuality Assurance 制造品质保证SSQA Sales and serviceQuality Assurance 销售及服务品质保证LRR Lot Rejeet Rate批退率BS Brain storming 脑力激荡EMI ElectronicMagnetion Inspect 高磁测试FMI FrequencyModulatim Inspect 高频测试B/M Boar/Molding(flatcable)C/P Connector of PCA/P AssemblySPS Switching powersupply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital VedioDiskVCD Vdeio CompactDiskLCD Liquid CrystalDisplayCAD Computer AIDDesignCAM Computer AIDManufacturingCAE Computer AIDEngineeringABIOS AchancedBasic in put/outputsystem 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微通道结构EISA ExtendedIndustry StandardArchitecture 扩充的工业标准结构SIMM Single in-linememory module 单项导通汇流组件DIMM Dual in-lineMemory Module 双项导通汇流组件LED Light-EmittingDiode 发光二级管FMEA Failure ModeEffectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed CircuitBoard 印刷电路板CAR Correction ActionReport 改善报告NG Not Good 不良WPR Weekly DeliveryRequirement 周出货要求PPM Parts Per Million百万分之一TPM Total ProductionMaintenance 全面生产保养MRP MaterialRequiremcnt Planning物料需计划OC Operation System作业系统TBA To Be Design待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-MusicIndustry 电子音乐工业RFI Read FrequencyInput 读频输入MMC MaximumMaterial ConditionMMS MaximumMaterial SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precisionforging 精密锻造cold forging 冷锻pressforging 冲锻compacting molding 粉末压出成形rocking dieforging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotationalmolding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding注入成形sand moldcasting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻sixsides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding中空(吹出)成形squeezecasting 高压铸造hot chamber die casting热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched diemethod 对模成形法laminating method 被覆淋膜成形low pressurecasting 低压铸造lost wax casting 脱蜡铸造matched mouldthermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold多模穴模具electroformed mold 电铸成形模multi-gatemold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold通气性模具duplicated cavity plate复板模positive mold全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ballplunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottomplate 下固定板bracket 托架bumperblock 缓冲块buster 堵口castingladle 浇注包casting lug 铸耳cavity模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowelhole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machinedround plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib凹形拉紧?goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guidepost 引导柱guide plate 导板guiderail 导轨head punch 顶?冲头。
机械-英语单词
互 补 金 属 氧 化 物 106 、 体 complementary metal oxide semiconductors (CMOS) 107 、 介子；垫片 washer 108 、 介指铁 ring mandrel 109 、 介电常数；电容率 permittivity 110 、 介稳态的；亚稳态的 metastable 111 、 内力 internal force 112 、 内卡尺 inside calipers 113 、 内能 internal energy 114 、 内涵性质 intensive properties 115 、 内圆弯凿 scribing gouge 116 、 内锁式配件 interlocking fitting 117 、 内燃机 internal combustion engine 118 、 内螺纹制造法 tapping 119 、 内螺丝 internal thread 120 、 内弯边 concave edge 121 、 六角金属枝 hexagonal bar 122 、 六角匙 Allen key 123 、 六角头螺丝 hexagonal head screw 124 、 公制的；十进制的 metric 125 、 公差 tolerance
1 、 一字螺丝批 slot type screwdriver 2 、 一点透视 one-point perspective 3 、 二合一黏合剂 epoxy resin adhesive 4 、 二合胶；混合胶 epoxy glue 5 、 二维的；平面的 two-dimensional 6 、 二进制 binary 7 、 二极管；整流子 diode 8 、 二号螺丝攻 second tap 9 、 二路开关 two-way switch 10 、 十进制的；公制的 metric 11 、 人工制品 artefact 12 、 人造板 man-made board 13 、 人体工程学 ergonomics; human engineering 14 、 人体尺寸 human dimension 15 、 人体测量学 anthropometry; anthropometrics 16 、 刀片 blade 17 、 刀身 blade 18 、 刀具 tool 19 、 刀具溜座 carriage 20 、 刀柱 tool post 21 、 刀架 tool rest 22 、 刀架底座 tool rest bracket 23 、 刀座帷；床鞍 apron 24 、 刀座鞍；溜板座 saddle 25 、 力 force 26 、 力三角形 triangle of force 27 、 力平行四边形 parallelogram of force 28 、 力多边形；多边形力学 polygon of force 29 、 力的分解 force resolution 30 、 力架；亮漆 lacquer 31 、 力矩 moment 32 、 力偶 couple 33 、 力矩定律 law of moment 34 、 力-距离图表 force-distance graph 35 、 力图 force diagram 36 、 力线 line of force 37 、 力点 effort 38 、 十字榫 cross halving joint 39 、 十字螺丝 Philip's head screw 40 、 十字螺丝批 Philip's type screwdriver 41 、 丁字尺；T 尺 tee square 42 、 三爪夹头 three-jaw chuck
机械专业英语单词整理
turret n.刀塔（炮塔）twist drill n.麻花钻taper n.锥度v.（使）成锥形bore v. 镗、钻（孔）boring n.镗、钻（孔）mill v.铣削，磨milling n.铣削，磨sharpened n.磨床，磨具mould n.模具v.浇铸forge v.锻造cast v.铸造cage n.保持架（轴承）addendum n.齿顶（高）dedendum n.齿根（高）top land n.齿顶部bottom land n.齿根部reference circle n.分度圆pitch n.齿距module n.模数，组件line of action n.啮合线involute n.渐开线circumference n.周长，圆周normal n.法线，正交flange n.凸缘，轮缘flank n.侧面mesh v.啮合superpose v.放在上面，使重叠（重合）tangential a.切线的，正切的tangent n.切线，正切parabola n.抛物线parabolic a.抛物线的sinusoid n.正弦曲线sinusoidal a.正弦曲线的sine n.正弦cosine n.余弦chamfer n.斜面radii n.半径tilt v.(使)倾斜micron n.微米transversal a.横向的，截线的n.截线，贯线quench v.淬火union n.活接头valve n.阀，气门，电子管toner n.墨粉cartridge n.墨盒sustainability n.稳定性aluminum n.铝alloy n.合金epicycloid n.外摆线，圆外旋转线bevel n.斜面，斜边bevel gears n.锥齿轮spiral gear(helical gear)n.斜齿轮，螺旋齿轮beam n.（横）梁crossrail n.横梁gantry n.龙门架gasket n.垫圈，衬垫tutorial n.教程tube n.管rubber n.橡胶flange n.凸缘，轮缘，法兰tee n.T字型物grind v/n.磨，碾trajectory n.轨迹，轨道rated a.额定的threading n.车螺纹，攻丝turning n.车削，旋转，变向polygonal a.多边形的broaching n.拉削，铰孔，扩孔broach v. 拉削，铰孔，扩孔slotting n.开槽ventilation n.空气流通carriage n.托架，拖板travel n.行程bracket n.支架，托架coefficient n.[数]系数abrasion n.磨损hydrostatic a.流体静力学的，静压传动的symmetrical a.对称的asymmetry n.不对称asymmetrical a.不对称的film n.薄膜pad n.垫，衬垫slipper n.滑块part n.零件，部件agile a.敏捷的，轻快的，灵活的backlash n.侧隙，间隙，游隙finish n.（表面）光洁度flatness n.平面度compatibility n.兼容性immunity n.免疫性，免疫力，抗扰度aid n.辅助设备cable n.电缆pressure n.电压metallic a.金属（性）的circuit n.电路，回路，网路，线路pressure n.压力，电压jack n.起重器，千斤顶hoist n.起重机，升降机，吊车lateral a.横（向）的，侧面的eyebolt n.吊环螺栓blank n.毛坯pallet n.货盘pneumatic a.空气的，气体的，风力的deaerate v.使除去空气kinetic a.（运）动的，动力（学）的kinematic a.运动学的elastomer n.人造橡胶，弹性体electrotechnics n.电工学electrotechnical a.intake n.(管道等的)入口drawbolt n.紧固螺栓drawscrew n.起模螺钉shank n.（入柄的）杆；轴杆柄diagram n.电路图plan n.设计图ambient a.周围的n.周围环境phosphatize v.使磷化vulcanize v.硫化，硬化nitrogen n.氮，氮气nickel v.镀镍n.镍zinc v.涂锌n.锌cadmium n.隔chrome n.铬tungsten n.钨titanium n.钛platinum n.铂，白金brass n.黄铜copper n.铜，紫铜zinc n.锌magnesium n.镁magnesia n.氧化镁manganese n.锰fluorocarbon n.碳氟化合物carbide n.碳化物galvanize v.通电，电镀counterbalance v.使平衡n.平衡力calibration n.校准run off v.进行（试验）duty n.负载，功guideway n.导轨hex 六角形（的），六边形（的）facelift n..翻新，整修compensate v.补偿quadric a.二次的n.二次曲面volumetric a..体积的，容积的prism n.棱柱benchmark n.基准velocity n.速度，速率，周转率angular a,角的harmonic n.谐波，谐函数offset n/v.偏移量，抵消，弥补temper v.回火anneal v.退火chasm n.深坑，裂口inelastic a.无弹性的viscoelastic a.黏弹性的coarsen v.（使）变粗糙anti-torsion rigidity 抗扭刚度bending rigidity 抗弯刚度compressive rigidity 抗压刚度stationary a.静止的，不动的nipple n.火门，喷嘴，螺纹接套outlet n.出口inlet n.入口displacement n.排水量clockwise a/ad 顺时针的（地）counter clockwise 逆时针方向link n.构件component n.构件stiffen v.(使)变硬cutter n.刀具file n.锉刀razor n.剃刀hook n.钩，吊钩v.钩住electromagnetism n.电磁，电磁学viscous a.粘性的，粘滞的stress n.应力support(constraint) n.约束condition n.场force n.载荷cartesian a.笛卡尔的polar n.极线，极面annulus n.环面spherical a.球的，球形的prism n.棱柱sphere n.球体cone n.圆锥体conical a.圆锥的torus n.圆环面diagonal n.对角线a.斜的saddle n.滑座，滑板cam n.凸轮drawbar n.拉杆，导杆，连接杆datum n.基点，基线，基面housing n.(机, 构, 框, 支, 骨)架, 轴承座, 机体[座]wobble n.摇动，晃动，不稳定v.（使）摇动，晃动anodize v.阳极电镀, 作阳极化处理roughness n.粗糙度roundness n.圆度cylindricity n.圆柱度coaxial=concentric a.同轴的concentricity n.同轴度parallelism n.平行度hysteresis n.滞后作用，磁滞现象swivel v.旋转groove n.凹槽v.开槽ceramic n/a.陶器的，陶瓷的clearance n.间隙elongation n.延长（线），延伸率concave a.凹的n.凹面convex a.凸的chuck n.（钻机等的）卡盘，夹盘gripper n.钳子，夹子plant n.工厂，成套设备、装置、机械rod n.杆，棒duct n.管道，输送管collet n.夹头retention n.保持力sparepart n.备件，零配件solenoid n.螺线管teflon n.聚四氟乙烯cryogenic a.低温学的engagement n.接合ratchet n.（防倒转的）棘轮v.安装棘轮于，松脱ratchetting n.松脱振动energise v.使通电pole n.电极，磁极sleeve n.套管，衬套bushing n.轴衬，套管probe n.探测器，探针drainage n.排水, 排泄, 排水装置graphite n.石墨cavity n.腔，洞stall torque n.堵转扭矩stall current n.堵转电流piston n.活塞coil n.卷，盘tensile a.拉力的，可伸长的curvature n.曲率，弯曲analog n.模拟elliptical a.椭圆的circular a.圆形的，椭圆的tribology n.摩擦学kelmet n.油膜轴承journal bearings n.滑动轴承recess n.凹处v.制造凹陷clearance n.空隙，间隙elastohydrodynamica.流体弹性动力（学）的hydrodynamic a.流体动力学的，水力的behavior n.性状critical a.临界的gyroscopic a.回转仪的repulsion n.推力，排斥density n.密度viscosity n.粘度spillage n.溢出（量）immersion n.陷入，浸入glossary n.词汇表，汇编glossy a.平滑的，有光泽的matte a.不光滑的thermometer n.温度计resistor n.电阻（器）resistance n.阻力，电阻，阻抗proximity n.接近ultrasonic a.超音速的n.超声波photoelectric n.光电的hydrolysis n.水解splatter n.飞溅，干扰halogen n.卤素acid n.酸alkali n.碱chiller n.冷却机embed v.（使）插入，嵌入nonferrous a.不含铁的，非铁的fit n.配合reamer n.扩孔锥; 铰刀; 铰床;整孔钻[器], 锪钻counterbore v.(用平底扩孔钻)扩孔［锪孔，镗孔，镗阶梯孔bur n.磨石synthetic a.合成的, 人造的, 综合的wrought a.锻造的edm 放电加工satin finish 磨光leaf spring 钢板弹簧sandblast n./v.喷沙fraction n.分数decimal n.小数logarithm n.对数algebra n.代数（学）felt n.毛毡aerostatic a.空气静力学的gib n.凹字型楔phenolic adj.[化]酚的, 石碳酸的phenolics n.酚醛塑料herringbone adj.鲱骨状的;人字形的polymer n.聚合物backup ring 挡圈transducer n.变频器，变换器hinge n.铰链solvent n.溶剂galvanize v.电镀，镀锌，电刺激graphite n.石墨，墨铅，铅笔粉pinion n.小齿轮inline 内联chromeplate v.镀铬nozzle n.管嘴，喷嘴metallurgical a.冶金学的atomise v.使分裂成原子，将…喷成雾状strainer n.滤网siphon n.弯管，虹吸管phosphate n.磷酸盐degrease v.脱脂，除油污oil mist 油雾portal n.桥门grate n.磨碎，压碎malleable a.可锻造的dashed n.虚线varnish n.清漆，罩光漆foundry n.铸造, 翻砂, 铸工厂foundry goods n.铸件attrition n.磨擦，磨损perpendicularity n.垂直度straightness n.直线度stock n.台，座apparatus n.器械, 设备, 仪器pentagonal adj.五角的, 五边形的5-axies simultaneous machinen.五轴联动机床circuit-breaker n.断路器pedestal n. 基架，基座；基础；底座granite n.花岗岩polarity n.两极，极性assembler n.装配工indexing n.分度positioning accuracy n.定位精度repeat positioning accuracy n.重复定位精度repeatability n.重复定位精度tool magazine n.刀库longitudinal n.长度的，纵向的turbocharger n.涡轮增压器acrylic a.丙烯酸的resin n.树脂，松香excavator n.挖掘机，打洞机lever n.杠杆potentiometer n.电位计，电势机，分压器potentiometric a.uni-directional a.单向的porosity n.有孔性，多孔性diode n.二极管commissioning n.试车，试运转ripple n.（物理学）波动，脉动auxiliary n.辅助物，辅助机构eccentricity n.离心率，偏心距fixture n.夹具，装置器copolyester n.共聚酯，共聚多酯glycerine n.丙三醇，甘油manometer n.压力表（计）quill v.刺穿n.（机）套管轴spanner n.扳手bonderize v.磷化，在表面涂防腐剂porcelain n.瓷，瓷器a.瓷制的，精美的slave n.从动装置tandem a.串联的carriage n.大拖板hob n.滚刀v.滚铣oxidation n.氧化bionic a.仿生学的throttle n.节流阀vt.压制，使…节流vi.节流，减速hermetical a.与外界隔绝的，密封的electrochromic a.电致变色的n.电色显示器lamellar a.片/层状的，薄膜（片）的apex n.顶尖，顶点centrifugal a.离心的n.离心机skew n.a.斜交（的），歪斜（的）profiling n.压型，仿形切削yield strength n.屈服强度tensile strength n.抗拉强度gradient n.[数、物]梯度、坡度、倾斜度a.倾斜的clearance-free a.无间隙的reciprocate vi.往复运动reciprocation n.往复运动brinelling n.渗碳硬化，布氏硬度试验stoppage n.停止，故障，罢工，堵塞，扣留spacer n.垫片counterstay n.控制台slippage n.滑程，滑动量，滑移，下降pre-ground a.事先磨好的even a.[数]偶数的，平坦的，相等的intermediate vi.起媒介作用a.中间的，中级的n.中间物，媒介。
机械行业英语
机械行业英语以下是二十个机械行业相关的英语单词、释义、短语、用法和双语例句：一、bolt（螺栓）1. 释义- n. 螺栓；（门或窗的）插销；弩箭。
- vt. 筛选；囫囵吞下；（把门、窗等）闩上；突然说出，脱口说出。
2. 短语- bolt hole（螺栓孔）- loose bolt（松动的螺栓）- bolt cutter（断线钳，螺栓切割器）3. 用法- 作名词时，可用于描述机械部件连接中的螺栓。
作动词时，可表示固定或关闭的动作。
4. 双语例句- Noun: We need to tighten the bolts on this machine.（我们需要拧紧这台机器上的螺栓。
）- Verb: She bolted the door before going to bed.（她睡觉前闩上了门。
）二、gear（齿轮）1. 释义- n. 齿轮；装置，用具；传动装置；排挡。
- vt. 使适应；装上齿轮；用齿轮连接。
- vi. 适合；搭上齿轮；开始工作。
2. 短语- gear box（齿轮箱）- spur gear（正齿轮）- helical gear（斜齿轮）3. 用法- 作名词时，是机械传动系统中的重要部件。
作动词时，用于表示调整使适应或连接齿轮等动作。
4. 双语例句- Noun: The gears in this transmission are well - designed.（这个变速器里的齿轮设计得很好。
）- Verb: Thepany is gearing up for a big production increase.（公司正在为大幅提高产量做准备。
）三、shaft（轴）1. 释义- n. 轴；杆状物；箭杆；杆身。
- vt. 欺骗；苛待。
2. 短语- drive shaft（传动轴）- shaft diameter（轴直径）- crankshaft（曲轴）3. 用法- 主要作名词，在机械中用于描述转动或传递动力的部件。
机械专业英语词汇(+音标)
机械专业英语词汇金属切削metal cutting [英] [ˈmetl][美] [ˈmɛtl]机床machine tool [英] [məˈʃi:n tu:l][美] [məˈʃin tul]金属工艺学technology of metals [tekˈnɔlədʒi] [ˈmetl]刀具cutter['kʌtɚ]摩擦friction['frikʃən][’frɪkʃən]联结link [liŋk]传动drive/transmission [trænzˈmiʃən]轴shaft [ʃɑ:ft]弹性elasticity[ɪlæ'stɪsɪti:, ,i:læ-][ɪlæ'stɪsɪti, ,ilæ-]频率特性frequency characteristic ['fri:kwənsi][ˌkæriktəˈristik]误差error[ˈerə]响应response[ri'spɔns]定位allocation[ˌæləˈkeiʃən]机床夹具jig[dʒɪg]动力学dynamic[dai'næmik]运动学kinematic[,kaini'mætik]静力学static[ˈstætik]分析力学analyse mechanics[ˈænəlaiz] .[mɪˈkænɪks]拉伸pulling['puliŋ]压缩hitting[hitiŋ]剪切shear[ʃiə]扭转twist[twist]弯曲应力bending stress['bendiŋ] .[stres]强度intensity[inˈtensiti]三相交流电three-phase AC[feiz]磁路magnetic circles[mæɡˈnetik] .[ˈsə:kl]变压器transformer[trænsˈfɔ:mə]异步电动机asynchronous motor[ei'siŋkrənəs] ['məutə]几何形状geometrical[dʒɪəˈmetrɪkəl]精度precision[priˈsiʒən]正弦形的sinusoid[ˈsainəˌsɔid]交流电路AC circuit [ˈsə:kit]机械加工余量machining allowance [mə'ʃi:niŋ] .[əˈlauəns]变形力deforming force [dɪˈfɔ:miŋ] .[fɔ:s]变形deformation [ˌdi:fɔ:ˈmeɪʃən, ˌdefə-]应力stress [stres]硬度rigidity [rɪˈdʒɪdɪti:]]热处理heat treatment [ˈtri:tmənt]退火anneal [əˈni:l]正火normalizing ['nɔ:məlaiziŋ]脱碳decarburization [di:,kɑ:bjuərai'zeiʃən]渗碳carburization [,kɑ:bjurai'zeiʃən]电路circuit [ˈsə:kit]半导体元件semiconductor element [ˌsemikənˈdʌktə] .[ˈelimənt] 反馈feedback [ˈfi:dbæk]发生器generator [ˈdʒenəreitə]直流电源DC electrical source [i'lektrikəl] .[sɔ:s]门电路gate circuit [ɡeit] [ˈsə:kit]逻辑代数logic algebra [ˈlɔdʒik] .[ˈældʒibrə]外圆磨削external grinding [eksˈtə:nl] ['ɡraindiŋ]内圆磨削internal grinding [inˈtə:nəl] ['ɡraindiŋ]平面磨削plane grinding [plein] ['ɡraindiŋ]变速箱gearbox [ˈɡiəbɔks]离合器clutch [klʌtʃ]绞孔fraising [freiziŋ]绞刀reamer D.J.[ˈri:mə]螺纹加工thread processing [θred] .[prəʊˈsesɪŋ]螺钉screw [skru:]铣削mill [mil]铣刀milling cutter [ˈmiliŋ] .[ˈkʌtə]功率power [ˈpauə]工件workpiece [ˈwɜ:kpi:s]齿轮加工gear machining [ɡiə] [mə'ʃi:niŋ]齿轮gear [ɡiə]主运动main movement [mein] .[ˈmu:vmənt]主运动方向direction of main movement [diˈrekʃən]进给方向direction of feed [diˈrekʃən] .[fi:d]进给运动feed movement [fi:d] [ˈmu:vmənt]合成进给运动resultant movement of feed [riˈzʌltənt] [ˈmu:vmənt] [fi:d]合成切削运动resultan t movement of cutting [riˈzʌltənt] [ˈmu:vmənt][ˈkʌtɪŋ]合成切削运动方向direction of resultant movement of cutting [diˈrekʃən] [riˈzʌltənt] [ˈmu:vmənt] [ˈkʌtɪŋ] 切削深度cutting depth [ˈkʌtɪŋ] .[depθ]前刀面rake face [reik][ feis]刀尖nose of tool [nəuz] .[tu:l]前角rake angle [reik] .[ˈæŋɡl]后角clearance angle [ˈkliərəns] .[ˈæŋɡl]龙门刨削planing [plæniŋ]主轴spindle [ˈspɪndl]主轴箱headstock [ˈhedstɔk]卡盘chuck [tʃʌk]加工中心machining center [mə'ʃi:niŋ]车刀lathe tool [leɪð] .[tu:l]车床lathe [leɪð]钻削镗削bore [bɔ:]车削turning [ˈtɜ:nɪŋ]磨床grinder [ˈgraɪndə]基准benchmark [ˈbentʃˌmɑ:k]钳工locksmith [ˈlɔkˌsmɪθ]锻forge [fɔ:dʒ]压模stamping [ˈstæmpiŋ]焊weld [weld]拉床broaching machine ['brəutʃiŋ] .[məˈʃi:n]拉孔broaching['brəutʃiŋ]装配assembling [ə'sembliŋ]铸造found [faund]流体动力学fluid dynamics ['flu(:)id] [dai'næmiks]流体力学fluid mechanics ['flu(:)id] [mi'kæniks]加工machining [mə'ʃi:niŋ]液压hydraulic pressure [hai'drɔ:lik] ['preʃə]切线tangent ['tændʒənt]机电一体化mechanotronics mechanical-electrical integration [,mekənə'trɔniks] [mi'kænikl] [i'lektrikəl] [,inti'ɡreiʃən]气压air pressure pneumatic pressure [nju(:)'mætik]稳定性stability [stə'biliti]介质medium ['mi:djəm]液压驱动泵fluid clutch ['flu(:)id] [klʌtʃ]液压泵hydraulic pump [hai'drɔ:lik] [pʌmp]阀门valve [vælv]失效invalidation [in'vælideiʃn]强度intensity [in'tensiti]载荷load [ləud]应力stress [stres]安全系数safety factor ['seifti] ['fæktə]可靠性reliability [ri,laiə'biliti]螺纹thread [θred]螺旋helix ['hi:liks]键spline [splain]销pin [pin]滚动轴承rolling bearing ['rəuliŋ] ['bɛəriŋ]滑动轴承sliding bearing ['slaidiŋ] ['bɛəriŋ]弹簧spring [spriŋ]制动器arrester brake [ə'restə] [breik]十字结联轴节crosshead ['krɔshed]联轴器coupling ['kʌpliŋ]链chain [tʃein]皮带strap [stræp]精加工finish machining ['finiʃ] [mə'ʃi:niŋ]粗加工rough machining [rʌf] [mə'ʃi:niŋ]变速箱体gearbox casing ['ɡiəbɔks] ['keisiŋ]腐蚀rust [rʌst]氧化oxidation [ɔksi'deiʃən]磨损wear [wɛə]耐用度durability [,djuərə'biliti]随机信号random signal ['rændəm] ['siɡnl]离散信号discrete signal [dis'kri:t] ['siɡnl]超声传感器ultrasonic sensor ['ʌltrə'sɔnik] ['sensə]集成电路integrate circuit ['intiɡreit] ['sə:kit]挡板orifice plate ['ɔrifis] [pleit]残余应力residual stress [ri'zidjuəl] [stres]套筒sleeve [sli:v]扭力torsion ['tɔ:ʃən]冷加工cold machining [mə'ʃi:niŋ]电动机electromotor [i,lektrəu'məutə]汽缸cylinder ['silində]过盈配合interference fit [,intə'fiərəns] [fit]热加工hot work [hɔt] [wə:k]摄像头CCD camera ['kæmərə]倒角rounding chamfer ['raundiŋ] ['tʃæmfə]优化设计optimal design ['ɔptiməl] [di'zain]工业造型设计industrial moulding design [in'dʌstriəl] ['məuldiŋ] [di'zain]有限元finite element ['fainait] ['elimənt]滚齿hobbing ['hɔbiŋ]插齿gear shaping [ɡiə] ['ʃeipiŋ]伺服电机actuating motor ['æktjueitiŋ] ['məutə]铣床milling machine ['miliŋ] [mə'ʃi:n]钻床drill machine [dril] [mə'ʃi:n]镗床boring machine ['bɔ:riŋ] [mə'ʃi:n]步进电机stepper motor ['stepə] ['məutə]丝杠screw rod [skru:] [rɔd]导轨lead rail [li:d] [reil]组件subassembly ['sʌbə'sembli]可编程序逻辑控制器Programmable Logic Controller PLC ['prəuɡræməbl] ['lɔdʒik] [kən'trəulə]电火花加工electric spark machining [i'lektrik] [spɑ:k] [mə'ʃi:niŋ] 电火花线切割加工electrical discharge wire – cutting [i'lektrikəl] [dis'tʃɑ:dʒ]相图phase diagram [feiz] ['daiəɡræm]固态相变solid state phase changes [feiz]有色金属nonferrous metal ['nɔn'ferəs] ['metl]陶瓷ceramics [si'ræmiks]合成纤维synthetic fibre [sin'θetic] ['faibə]电化学腐蚀electrochemical corrosion [i,lektrəu'kemikəl] [kə'rəuʒən]车架automotive chassis [ɔ:tə'məutiv] ['ʃæsi]悬架suspension [səs'penʃən]转向器redirector ['ri:di'rektə]变速器speed changer [spi:d] ['tʃeindʒə]板料冲压sheet metal parts [ʃi:t] ['metl] [pɑ:ts]孔加工spot facing machining [spɔt] ['feisiŋ] [mə'ʃi:niŋ]车间workshop ['wə:kʃɔp]工程技术人员engineer [,endʒi'niə]气动夹紧pneuma lock ['nju:mə] [lɔk]数学模型mathematical model [,mæθi'mætikəl]画法几何descriptive geometry [dis'kriptiv] [dʒi'ɔmitri] 机械制图Mechanical drawing [mi'kænikl] ['drɔ:iŋ] 投影projection [prə'dʒekʃən]视图view [vju:]剖视图pro ['prəufail] [tʃɑ:t]标准件standard component ['stændəd] [kəm'pəunənt] 零件图part drawing [pɑ:t] ['drɔ:iŋ]装配图assembly drawing [ə'sembli] ['drɔ:iŋ]尺寸标注size marking [saiz] ['mɑ:kiŋ]技术要求technical requirements刚度rigidity [ri'dʒiditi]内力internal force [in'tə:nl] [fɔ:s]位移displacement [dis'pleismənt]截面section ['sekʃən]疲劳极限fatigue limit [fə'ti:ɡ] ['limit]断裂fracture ['fræktʃə]塑性变形plastic distortion ['plæstik, plɑ:stik] [dis'tɔ:ʃən] 脆性材料brittleness material ['britl] [mə'tiəriəl] 刚度准则rigidity criterion [ri'dʒiditi] [krai'tiəriən]垫圈washer ['wɔʃə]垫片spacer ['speisə]直齿圆柱齿straight toothed spur gear [tu:ðd] [spə:]斜齿圆柱齿轮helical-spur gear ['helikəl] [spə:][ɡiə]直齿锥齿轮straight bevel gear [streit] ['bevəl] [ɡiə]运动简图kinematic sketch [,kaini'mætik] [sketʃ]齿轮齿条pinion and rack ['pinjən] [ræk]蜗杆蜗轮worm and worm gear [wə:m] [ɡiə]虚约束passive constraint ['pæsiv] [kən'streint]曲柄crank [kræŋk]摇杆racker ['rækə]凸轮cams [kæm]共轭曲线conjugate curve ['kɔndʒuɡit] [kə:v]范成法generation method [,dʒenə'reiʃən] ['meθəd]定义域definitional domain [,defi'niʃən] [dəu'mein]值域range [reindʒ]导数\\微分differential coefficient [,difə'renʃəl] [kəui'fiʃənt]求导derivation [deri'veiʃən]定积分definite integral ['definit] ['intiɡrəl]不定积分indefinite integral [in'definit] ['intiɡrəl]曲率curvature ['kə:vətʃə]偏微分partial differential ['pɑ:ʃəl] [,difə'renʃəl]毛坯rough [rʌf]游标卡尺slide caliper [slaid] ['kælipə]千分尺micrometer calipers [mai'krɔmitə] ['kælipəs]攻丝tap [tæp]二阶行列式second order determinant ['sekənd] [' ɔ:də] [di'tə:minənt]逆矩阵inverse matrix ['in'və:s] ['meitriks]线性方程组linear equations ['liniə] [i'kweiʃən]概率probability [,prɔbə'biliti]随机变量random variable ['rændəm] ['vɛəriəbl]排列组合permutation and combination [,pə:mju(:)'teiʃən] [,kɔmbi'neiʃən]气体状态方程equation of state of gas [i'kweiʃən] [steit] [ɡæs]动能kinetic energy [kai'netik] ['enədʒi]势能potential energy [pə'tenʃəl] ['enədʒi]机械能守恒conservation of mechanical energy [,kɔ nsə(:)'veiʃən] [mi'kænikl] ['enədʒi]动量momentum [məu'mentəm]桁架truss [trʌs]轴线axes ['æksi:z]余子式cofactor [kəu'fæktə]逻辑电路logic circuit ['lɔdʒik] ['sə:kit]触发器flip-flop ['flipflɔp]脉冲波形pulse shape [pʌls] [ʃeip]数模digital analogy ['didʒitl] [ə'nælədʒi]液压传动机构fluid drive mechanism ['flu(:)id] [draiv] ['mekənizəm] 机械零件mechanical parts [mi'kænikl] [pɑ:t]淬火冷却quench [kwentʃ]淬火hardening ['hɑ:dəniŋ]回火tempering ['tempəriŋ]调质hardening and tempering ['hɑ:dəniŋ] ['tempəriŋ]磨粒abrasive grain [ə'breisiv] [ɡrein]结合剂bonding agent ['bɔndiŋ] ['eidʒənt]砂轮grinding wheel ['ɡraindiŋ] [wi:l, hw-]机械零件mechanical parts [mi'kænikl] [pɑ:t]淬火冷却quench [kwentʃ]淬火hardening ['hɑ:dəniŋ]回火tempering ['tempəriŋ]调质hardening and tempering ['hɑ:dəniŋ] ['tempəriŋ]磨粒abrasive grain [ə'breisiv] [ɡrein]结合剂bonding agent ['bɔndiŋ] ['eidʒənt]砂轮grinding wheel ['ɡraindiŋ] [wi:l, hw-]机床行业部分英汉对照按英文字母排序3-Jaws indexing spacers[dʒɔ:] ['indeksiŋ] ['speisə]三爪分割工具头A T C system ['sɪstəm]加工中心机刀库Aluminum continuous melting & holding furnaces [ə'lu:mənəm] [kən'tinjuəs] ['meltiŋ] ['həuldiŋ] ['fə:nis] 连续溶解保温炉Balancing equipment ['bælənsiŋ] [i'kwipmənt]平衡设备Bayonet ['beɪənɪt, -,net, ,beɪə'net]卡口Bearing fittings ['bɛəriŋ] ['fitiŋ]轴承配件Bearing processing equipment ['bɛəriŋ] [prəu'sesiŋ] [i'kwipmənt]轴承加工机Bearings ['bɛəriŋ]轴承Belt drive [belt] [draɪv]带传动Bending machines ['bendiŋ] [mə'ʃi:n]弯曲机Blades [bleid]刀片Blades,saw [bleid] [sɔ:]锯片Bolts,screws&nuts [bəult][skru:][nʌts]螺栓,螺帽及螺丝Boring heads ['bɔ:riŋ] [hed]搪孔头Boring machines ['bɔ:riŋ] [mə'ʃi:n]镗床Cable making tools ['keibl] ['meikiŋ] [tu:l]造线机Casting,aluminium ['kæstɪŋ] [,ælju:'minjəm]铸铝Casting,copper ['kæstɪŋ] ['kɔpə]铸铜Casting,gray iron ['kæstɪŋ] [ɡrei] ['aiən]铸灰口铁Casting,malleable iron ['kæstɪŋ] ['mæliəbl]可锻铸铁Casting,other ['kæstɪŋ]其他铸造Casting,steel ['kæstɪŋ] [sti:l]铸钢Chain drive [tʃein] [draɪv]链传动Chain making tools [tʃein]造链机Chamfer machines ['tʃæmfə] [mə'ʃi:n]倒角机Chucks [tʃʌk]夹盘Clamping/holding systems ['klæmpiŋ]夹具/支持系统CNC bending presses （CNC=Computerized Numerical Control [kəm'pju:tə] [nju(:)'merikəl] [kən'trol]）['bendiŋ] [pres] 电脑数控弯折机CNC boring machines ['bɔ:riŋ] [mə'ʃi:n]电脑数控镗床CNC drilling machines ['driliŋ] [mə'ʃi:n]电脑数控钻床CNC EDM wire-cutting machines（EDM=Electron Discharge Machining [i'lektrɔn] [dis'tʃɑ:dʒ] [mə'ʃi:niŋ]放电加工）[mə'ʃi:n] ['waiə]电脑数控电火花线切削机CNC electric discharge machines [i'lektrik] [dis'tʃɑ:dʒ] [mə'ʃi:n]电脑数控电火花机CNC engraving machines [en'greɪvɪŋ] [mə'ʃi:n]电脑数控雕刻机CNC grinding machines ['ɡraindiŋ] [mə'ʃi:n]电脑数控磨床CNC lathes [leið]电脑数控车床CNC machine tool fittings [mə'ʃi:n] [tu:l] ['fitiŋ]电脑数控机床配件CNC milling machines ['miliŋ] [mə'ʃi:n]电脑数控铣床CNC shearing machines ['ʃiəriŋ] [mə'ʃi:n]电脑数控剪切机CNC toolings CNC ['tu:liŋ]刀杆CNC wire-cutting machines ['waiə] ['kʌtiŋ] [mə'ʃi:n] 电脑数控线切削机Conveying chains [kən'veiiŋ] [tʃein]输送链Coolers ['ku:lə]冷却机Coupling ['kʌpliŋ]联轴器Crimping tools [krimpiŋ] [tu:l]卷边工具Cutters ['kʌtə]刀具Cutting-off machines ['kʌtiŋ] [mə'ʃi:n]切断机Diamond cutters ['daiəmənd] ['kʌtə]钻石刀具Dicing saws ['daisiŋ] [sɔ:]晶圆切割机Die casting dies [dai] ['kɑ:stiŋ]压铸冲模Die casting machines [dai] ['kɑ:stiŋ] [mə'ʃi:n]压铸机Dies-progressive [dai] [prə'ɡresiv]连续冲模Disposable toolholder bits [dis'pəuzəbl] ['tu:l,həuldə] [bit]舍弃式刀头Drawing machines ['drɔ:iŋ] [mə'ʃi:n]拔丝机Drilling machines ['driliŋ] [mə'ʃi:n]钻床Drilling machines bench ['driliŋ] [mə'ʃi:n] [bentʃ]钻床工作台Drilling machines,high-speed ['driliŋ] [mə'ʃi:n] [hai] [spi:d]高速钻床Drilling machines,multispindle [,m ʌlti] ['spindl]多轴钻床Drilling machines,radial ['driliŋ] [mə'ʃi:n] ['reidjəl]摇臂钻床Drilling machines,vertical ['driliŋ] [mə'ʃi:n] ['və:tikəl] 立式钻床drills [dril]钻头Electric discharge machines(EDM) [i'lektrik] [dis'tʃɑ:dʒ]电火花机Electric power tools [i'lektrik] ['pauə] [tu:l]电动刀具Engraving machines [en'greɪvɪŋ] [mə'ʃi:n]雕刻机Engraving machines,laser [en'greɪvɪŋ] [mə'ʃi:n] ['leizə]激光雕刻机Etching machines ['etʃiŋ] [mə'ʃi:n]蚀刻机Finishing machines ['finiʃiŋ] [mə'ʃi:n]修整机Fixture ['fikstʃə]夹具Forging dies ['fɔ:dʒiŋ] [dai]锻模Forging,aluminium ['fɔ:dʒiŋ] [,ælju:'minjəm]锻铝Forging,cold ['fɔ:dʒiŋ] [kəuld]冷锻Forging,copper ['fɔ:dʒiŋ] ['kɔpə]铜锻Forging,other ['fɔ:dʒiŋ] ['ʌðə]其他锻造Forging,steel ['fɔ:dʒiŋ] [sti:l]钢锻Foundry equipment ['faundri] [i'kwipmənt]铸造设备5 Gear cutting machines [ɡiə] ['kʌtiŋ] [mə'ʃi:n]齿轮切削机Gears [ɡiə]齿轮Gravity casting machines ['ɡræviti] ['kɑ:stiŋ] [mə'ʃi:n]重力铸造机Grinder bench ['ɡraində] [bentʃ]磨床工作台Grinders,thread ['ɡraində] [θred]螺纹磨床Grinders,tools & cutters ['ɡraində] [tu:l] ['kʌtə]工具磨床Grinders,ultrasonic ['ɡraində] ['ʌltrə'sɔnik]超声波打磨机Grinding machines ['ɡraindiŋ] [mə'ʃi:n]磨床Grinding machines,centerless ['ɡraindiŋ] [mə'ʃi:n] ['sentəles]无心磨床Grinding machines,cylindrical [si'lindrik(ə)l]外圆磨床Grinding machines,universal [,ju:ni'və:səl]万能磨床Grinding tools ['ɡraindiŋ] [tu:l]磨削工具Grinding wheels ['ɡraindiŋ] [wi:l, hw-]磨轮Hand tools [hænd] [tu:l]手工具Hard/soft and free expansion sheet making plant[iks'pænʃən] [ʃi:t]硬(软)板(片)材及自由发泡板机组Heat preserving furnaces [pri'zə:v] ['fə:nis]保温炉Heating treatment funaces ['tri:tmənt] ['fə:nis]熔热处理炉Honing machines ['həuniŋ] [mə'ʃi:n]搪磨机Hydraulic components [hai'drɔ:lik][kəm'pəunənt]液压元件Hydraulic power tools [hai'drɔ:lik]液压工具Hydraulic power units [hai'drɔ:lik]液压动力元件Hydraulic rotary cylinders['rəutəri] ['silində]液压回转缸Jigs [dʒiɡ]钻模Lapping machines ['læpiŋ] [mə'ʃi:n]精研机Lapping machines,centerless无心精研机Laser cutting ['leizə] ['kʌtiŋ]激光切割Laser cutting for SMT stencil['stensl, -sil]激光钢板切割机Lathe bench ['leizə] [bentʃ]车床工作台Lathes,automatic ['leizə] [,ɔ:tə'mætik]自动车床Lathes,heavy-duty ['leizə] [hevi:'du:ti:, -'dju:-]重型车床Lathes,high-speed ['leizə] [hai] [spi:d]高速车床Lathes,turret ['leizə] ['tʌrit]六角车床Lathes,vertical ['leizə] ['və:tikəl]立式车床Lubricants ['lu:brikənt]润滑液Lubrication Systems [,lu:bri'keiʃən] ['sɪstəm]润滑系统Lubricators ['lju:brikeitə]注油机Machining centers,general [mə'ʃi:niŋ] ['sentə] ['dʒ enərəl]通用加工中心Machining centers,horizontal [mə'ʃi:niŋ] ['sentə] [,h ɔri'zɔntl]卧式加工中心Machining centers,horizontal & vertical [mə'ʃi:niŋ] ['sentə] [,hɔri'zɔntl] ['və:tikəl]卧式及立式加工中心Machining centers,vertical [mə'ʃi:niŋ] ['sentə] ['və:tikəl]立式加工中心Machining centers,vertical double-column type [mə'ʃi:niŋ] ['sentə] ['və:tikəl] ['dʌbl] ['kɔləm] [taip]立式双柱加工中心Magnetic tools [mæɡ'netik] [tu:l]磁性工具Manifolds ['mænifəuld]集合管Milling heads ['miliŋ] [hed]铣头Milling machines ['miliŋ] [mə'ʃi:n]铣床Milling machines,bed type ['miliŋ] [mə'ʃi:n] [taip]床身式铣床Milling machines,duplicating ['miliŋ] [mə'ʃi:n] ['dju:plikeitiŋ]仿形铣床Milling machines,horizontal ['miliŋ] [mə'ʃi:n] [,hɔri'z ɔntl]卧式铣床Milling machines,turret vertical ['miliŋ] [mə'ʃi:n] ['tʌ rit] ['və:tikəl]六角立式铣床Milling machines,universal ['miliŋ] [mə'ʃi:n] [,ju:ni'və:səl]万能铣床Milling machines,vertical ['miliŋ] [mə'ʃi:n] ['və:tikəl]立式铣床Milling machines,vertical & horizontal ['miliŋ] [mə'ʃ i:n] ['və:tikəl] [,hɔri'zɔntl]立式及卧式铣床Mold & die components [məuld] [dai] [kəm'pəunənt] 模具单元Mold changing systems [məuld] ['tʃeindʒiŋ] ['sɪstəm] 换模系统Mold core [məuld] [kɔ:]模芯Mold heaters/chillers [məuld] ['hi:tə] ['tʃilə]模具加热器/冷却器Mold polishing/texturing [məuld] ['pɔliʃiŋ] ['tekstʃəriŋ]模具打磨/磨纹Mold repair [məuld] [ri'pɛə]模具维修Molds [məuld]模具Nail making machines [neil] [mə'ʃi:n]造钉机Oil coolers [ɔil] ['ku:lə]油冷却器Overflow cutting machines for aluminium wheels ['əuvə'fləu] [mə'ʃi:n] [,ælju:'minjəm] [wi:l, hw-]铝轮冒口切断机P type PVC waterproof rolled sheet making plant 6 [taip] ['wɔ:təpru:f] [rəuld] [ʃi:t] [plɑ:nt] PPVC高分子防水PCB fine piecing systems [fain] [pi:s] ['sɪstəm]( PCB =Printed -circuit Board [bɔ:d]印刷电路板)印刷电器板油压冲孔脱料系统Pipe & tube making machines [paip] [mə'ʃi:n] ['tju:b] [mə'ʃi:n]管筒制造机Planing machines [plæniŋ] [mə'ʃi:n]刨床Planing machines vertical [plæniŋ] [mə'ʃi:n] ['və:tikəl]立式刨床Pneumatic hydraulic clamps [nju(:)'mætik] [hai'dr ɔ:lik] [klæmp]气油压虎钳Pneumatic power tools [nju(:)'mætik] ['pauə] [tu:l]气动工具Powder metallurgic forming machines ['paudə] [,metə'lə:dʒik] ['fɔ:miŋ] [mə'ʃi:n]粉末冶金成型机Presses,cold forging [pres] ['fɔ:dʒiŋ]冷锻冲压机presses,crank [pres] [kræŋk]曲柄压力机Presses,eccentric [pres] [ik'sentrik]离心压力机Presses,forging [pres] ['fɔ:dʒiŋ]锻压机Presses,hydraulic [pres]液压冲床Presses,knuckle joint [pres]肘杆式压力机Presses,pneumatic [pres] [hai'drɔ:lik]气动冲床Presses,servo [pres] ['sə:vəu]伺服冲床Presses,transfer [pres] [træns'fə:]自动压力机Pressing dies [presiŋ] ['daii:z]压模Punch formers [pʌntʃ] ['fɔ:mə]冲子研磨器Quick die change systems [kwik] [dai] [tʃeindʒ] ['sɪ stəm]速换模系统Quick mold change systems [kwik] [məuld] [tʃeindʒ] ['sɪstəm]快速换模系统Reverberatory furnaces [ri'və:bərətəri] ['fə:nis]反射炉Rollers ['rəulə]滚筒Rolling machines ['rəuliŋ] [mə'ʃi:n]辗压机Rotary tables ['rəutəri] ['teibl]转台Sawing machines ['sɔ:iŋ] [mə'ʃi:n]锯床Sawing machines,band ['sɔ:iŋ] [mə'ʃi:n] [bænd]带锯床Saws,band [sɔ:] [bænd]带锯Saws,hack [sɔ:] [hæk]弓锯Saws,horizontal band [sɔ:] [,hɔri'zɔntl] [bænd]卧式带锯Saws,vertical band [sɔ:] ['və:tikəl] [bænd]立式带锯shafts [ʃɑ:ft]轴Shapers ['ʃeipə]牛头刨床Shearing machines ['ʃiəriŋ] [mə'ʃi:n]剪切机Sheet metal forming machines [ʃi:t] ['metl] ['fɔ:miŋ] [mə'ʃi:n]金属板成型机Sheet metal working machines [ʃi:t] ['metl] [mə'ʃi:n]金属板加工机Slotting machines ['slɔtiŋ] [mə'ʃi:n]插床spindles ['spindl]主轴Stamping parts ['stæmpiŋ] [pɑ:t]冲压机Straightening machines ['streitniŋ] [mə'ʃi:n]矫直机Switches & buttons [switʃ] ['bʌtn]开关及按钮Tapping machines ['tæpiŋ] [mə'ʃi:n]攻螺丝机Transmitted chains [trænz'mit] [tʃein]传动链Tube bending machines ['tju:b] ['bendiŋ] [mə'ʃi:n]弯管机Vertical hydraulic broaching machine ['və:tikəl] [hai'drɔ:lik] ['brəutʃiŋ] [mə'ʃi:n]立式油压拉床Vises [vais]虎钳Vises,tool-maker [vais][ 'tu:l,meɪkə]精密平口钳Wheel dressers [wi:l, hw-] ['dresə]砂轮修整器Woven-Cutting machines ['wəuvən]织麦激光切割机Wrenches [rentʃ]扳手螺丝词汇的中英文对照六角盖头螺帽HEX CAP NUTS (HEX= hexagon ['heksəɡən] 六角形; 六边形) [kæp] [nʌts]六角锯齿螺帽HEX SERRATED NUTS (HEX= hexagon ['heksəɡən] 六角形; 六边形) [se'reitid [nʌts] 六角轮缘螺帽HEX FLANGE NUTS (HEX= hexagon ['heksəɡən] 六角形; 六边形) [flændʒ] [nʌts]高脚螺帽HEX COUPLING NUTS(HIGH NUTS) (HEX= hexagon ['heksəɡən] 六角形; 六边形) ['kʌpliŋ] [nʌts] [hai]圆螺帽ROUND NUTS [raund] [nʌts]四角螺帽SQUARE NUTS HEAVY HEX NUTS [skwɛə] [n ʌts] [ 'hevi] (HEX= hexagon ['heksəɡən] 六角形; 六边形)不锈钢六角螺帽STAINLESS STEEL HEX NUTS ['steinlis] [sti:l] (HEX= hexagon ['heksəɡən] 六角形; 六边形) [n ʌts]不锈钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS ['steinlis] [sti:l] ['nailən] [in'sə:t] [lɔk] [nʌts] 普通六角螺帽HEX NUTS (HEX= hexagon ['heksəɡən] 六角形; 六边形) [nʌts]六角重型螺帽HEAVY HEX NUTS [ 'hevi]['heksəɡən][nʌts]薄型螺帽HEX JAM NUTS ['heksəɡən][dʒæm] [nʌts]尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS ['nailən] [in'sə:t] [lɔk] [nʌts]机械螺丝用六角螺帽HEX MACHINE SCREW NUT ['heksəɡən] [mə'ʃi:n] 7 [skru:] [nʌt]机械工具英语机械工具spanner 扳子(美作:wrench) ['spænə] [rent ʃ] double-ended spanner ['spænə]双头扳子adjustable spanner, monkey wrench [ə'dʒʌstəbl] ['spænə] ['mʌŋki] [rentʃ]活扳子,活络扳手box spanner 管钳子(美作:socket wrench) [bɔks] ['spænə] ['sɔkit] [rentʃ]calipers ['kælipə]卡规pincers, tongs ['pinsəz] [tɔŋz]夹钳shears [ʃiəz]剪子hacksaw ['hæksɔ:]钢锯wire cutters ['waiə] ['kʌtə]剪线钳multipurpose pliers,universal pliers ['mʌlti'pə:pəs] ['plaiə] [,ju:ni'və:səl] ['plaiəz]万能手钳adjustable pliers [ə'dʒʌstəbl] ['plaiəz]可调手钳punch [pʌntʃ]冲子drill [dril]钻chuck [tʃʌk]卡盘scraper ['skreipə]三角刮刀reamer ['ri:mə]扩孔钻calliper gauge ['kælipə] [ɡedʒ]孔径规rivet ['rivit]铆钉nut [nʌt]螺母locknut ['lɔknʌt]自锁螺母,防松螺母bolt [bəult]螺栓pin, peg, dowel [pin] [peɡ] ['dauəl]销钉washer ['wɔʃə]垫圈staple ['steipl]U形钉oil can 油壶jack工作服grease gun [ɡri:s]注油枪机械加工抛光polishing ['pɔliʃiŋ]安装to assemble [ə'sembl]衬套bushing ['buʃiŋ]外贸常用机械英语大全Assembly line [ə'sembl]组装线Layout ['lei,aut]布置图Conveyer [kən'vei]流水线物料板Rivet table ['rivit]拉钉机Rivet gun ['rivit]拉钉枪Screw driver 起子Pneumatic screw driver [nju(:)'mætik]气动起子worktable ['wə:kteibl]工作桌OOBA 开箱检查fit together [tə'ɡeðə]组装在一起fasten ['fɑ:sn]锁紧(螺丝)ixture ['fikstʃə]夹具(治具)pallet ['pælit]栈板bar code [bɑ:] [kəud]条码bar code scanner [bɑ:] [kəud] ['skænə]条码扫描器fuse together [fju:z] [tə'ɡeðə]熔合fuse machine [fju:z] [mə'ʃi:n]热熔机repair[ri'pɛə]修理operator['ɔpəreitə]作业员QC [=Quality Control ['kwɔliti] [kən'trol]质量控制]品管supervisor ['sju:pəvaizə]课长ME [=Mechanical Engineer机械工程师]制造工程师MT 制造生技cosmetic inspect [kɔz'metik] [in'spekt]外观检查inner parts inspect ['inə] [in'spekt]内部检查thumb screw [θʌm]大头螺丝lbs inch [intʃ]镑、英寸EMI gasket ['ɡæskit]导电条front plate [frʌnt] [pleit]前板rear plate [riə] [pleit]后板chassis ['ʃæsi]基座bezel panel ['bezəl] ['pænl]面板power button ['pauə] ['bʌtn]电源按键reset button ['ri:set] ['bʌtn]重置键Hi-pot test of SPS [test]高源高压测试Voltage switch of SPS ['vəultidʒ] [switʃ]电源电压接拉键sheet metal parts [ʃi:t]冲件plastic parts ['plæstik, plɑ:stik]塑胶件SOP [=Standard Operating Procedure 标准操作程序] 制造作业程序material check list [mə'tiəriəl]物料检查表work cell [wə:k] [sel]工作间trolley ['trɔli]台车carton ['kɑ:tən]纸箱sub-line ['sʌblain]支线left fork [fɔ:k]叉车personnel resource department [,pə:sə'nel] [ri'sɔ:s] [di'pɑ:tmənt]人力资源部production department [prə'dʌkʃən]生产部门planning department ['plænɪŋ] [di'pɑ:tmənt]企划部QC Section ['sekʃən]品管科stamping factory ['stæmpiŋ] ['fæktəri]冲压厂painting factory ['peintiŋ]烤漆厂molding factory ['məuldiŋ] ['fæktəri]成型厂common equipment ['kɔmən] [i'kwipmənt]常用设备。
复试机械英语单词必备
Mentallurgical 冶金的 plasticity 可塑性 mineral 矿物Corrode 腐蚀Solvent 溶剂的Extrusion 挤压Mold 模型Die-casting 压铸Resist 抗，耐Disjoin 拆散Forging 锻造Drawing 制图，拉Symmetrical 对称的Solder 焊料Dissolve 使溶解inorganic 无机的 deform 使..变形rigid 刚性的 exploite 开发开拓forming 成型 foundry 铸造composition 成分 intricate 错综的die-maintenance 修理磨具hollow 中空的ingot 铸模block 毛坯graphite 石墨pronounced 显著的roughly 大体地hydraulic 液压的 draft 牵引力furnace 熔炉 pyrometer 高温计weld 焊接 trap 聚集夹杂squeeze 挤压 butt 对接Electrode 电极的Contract 收缩Distortion 变形Brittle 脆性易碎Specimen 试样Sustain 支撑Vital 活的Bevel 锥齿轮Mount 安装Coverage 范围Lead 导程Involute 渐开线Fabric 纤维molecular 分子的machining 切削quench 淬火annealing 退火grinding 磨削tempering 回火shear 剪切stiffness 刚性undue 过度transmit 传播preclude 妨碍mesh 啮合配合conduct 进行实施toughness 韧性elasticity 弹性helical 斜齿轮rotary 回转运动spur 直圆柱齿轮configuration 排列 deteriorate 损坏geometry 几何学 envelope 包住rack 齿条 versatility 通用性inherent 固有的 impeller 涡轮Variation 变化Elliptical 椭圆Screw 螺钉Oval 椭圆形的Nut 螺母Reciprocate 往复Separator 分离器Interpose 放入插入Mating 配合Spatical 空间的Winding 缠绕的Engagement 啮合Coefficient 系数compressure 压缩力 cantilever 悬臂proportion 部分/尺寸 diameter 直径truncate 截断 groove 沟槽stud 螺栓conjunction 结合magnitude 大小mild 温和的couping 联轴器alignment 对准coaxial 共轴的respect 方面friction 摩擦力pinch 夹紧clamp 夹具stretch 伸展bearing 轴承omit 省去wear 磨损interfere with 与..干扰rigidly 坚硬地clutch 离合器severe 剧烈的linkage 连杆Hinge 铰链 behave 工作性能specify 拟定技术Compatible 兼容的 visualize 目测constraint 约束Lubricant 润滑剂 encounter 遭遇viscosity 粘性Delicate 精密 abrasion 磨损处inhibitor 抑制剂Contaminant 污染物 asperity 粗糙度ambient 周围的Preservative 防腐的 neutralize 使..中和accommodate 调节Taper 圆锥Frame 框架Stock 原料thread 螺纹punch 冲压机fabrication 制作pitch 螺距versatility 多功能的slot 缝/槽Successively 连续 refinement 改进 incorporate 采用Duplicate 完全相同的/复制品 leakage 泄漏物Coil 线圈 interface 分界面 electromagnetic 电磁铁Chip 切削 portable 可移动的 revolution 旋转Assess 估计 scale 比例 discount 忽视Abrasive 有磨损力的 scrap 废弃Catastrophic 灾难的 criterion 标准 degradation 降级Tear 裂纹 ductile 可延展的Undulation 波动Replicate 重复Allowance 容差swarf 金属屑tolerance 公差split 分开clamp 夹紧impinge 冲击unilateral 单向empirical 经验的Feature 特点 identification 鉴别 inference 推理Typically 典型地 jack 增加 reap 获得Sprayer 喷射装置 contour 轮廓 fatigue 疲劳Optimize 优化 payload 有效载荷 manipulator 操作器Execute 执行 robust 稳定的 configuration 结构Fluctuate 脉动 intermediate 中间的 transformer 变压器Rectifier 整流器Archaically 旧式的Proprietary 专利的Terminal 终端Prototype 原型Batch 批量Fault 故障Intervention 干扰Iterative 迭代的Inductor 电感Element 元件Alleviate 减轻Nominal 额定的capacitor 电容器 relay 继电器retention 保留 versed 熟练的automatic 自动化 drafting 草图flip 翻转 kinematics 运动学respective 各自的 substantial 大量的conveyor 传递装置 hierarchy 层次module 模块 node 节点contouring 仿形 stiffness 刚度lateral 侧面的strain 应变变形halt 停止concise 简洁的differential 微分的transducer 传感器insight 直觉dictate 指令bastardize 使品质变坏 fastener 紧固件。
机械英语单词大全
机械英语单词大全Sure, I can provide you with a comprehensive list of mechanical engineering vocabulary. Here it is:1. Mechanical Engineering - 机械工程2. Gear - 齿轮3. Shaft - 轴4. Bearing - 轴承5. Friction - 摩擦6. Lubrication - 润滑7. Tension - 张力8. Compression - 压缩9. Torque - 扭矩10. Force - 力11. Velocity - 速度12. Acceleration - 加速度13. Stress - 应力14. Strain - 应变15. Fatigue - 疲劳16. Welding - 焊接17. Casting - 铸造18. Forging - 锻造19. Machining - 加工20. CNC (Computer Numerical Control) - 数控21. CAD (Computer-Aided Design) - 计算机辅助设计22. CAM (Computer-Aided Manufacturing) - 计算机辅助制造23. Thermodynamics - 热力学24. Fluid Mechanics - 流体力学25. Heat Transfer - 热传导26. Thermocouple - 热电偶27. HVAC (Heating, Ventilation, and Air Conditioning) - 暖通空调28. Pneumatics - 气动29. Hydraulics - 液压30. Kinematics - 运动学31. Dynamics - 动力学32. Vibration - 振动33. Resonance - 共振34. Material Science - 材料科学35. Alloy - 合金36. Composite - 复合材料37. Tensile Strength - 抗拉强度38. Yield Strength - 屈服强度39. Elastic Modulus - 弹性模量40. Ductility - 延展性41. Hardness - 硬度42. Creep - 蠕变43. Fatigue Strength - 疲劳强度44. Impact Strength - 冲击强度45. Toughness - 韧性46. Thermal Expansion - 热膨胀47. Electrical Conductivity - 电导率48. Corrosion Resistance - 耐腐蚀性49. Surface Roughness - 表面粗糙度50. Dimensional Tolerance - 尺寸公差这是一个涵盖机械工程领域的词汇列表，希望能帮助到你。
机械专业英语单词
acceleration 加速度，加速度值，加快adaptive 适合的，适应的，自适应的adaptive control 自适应控制bearing 轴承，支撑blade 叶片，刀片boring 镗孔，镗削加工bar stock 棒料bench type 台式burr 毛刺back engagement 背吃刀量cam 凸轮，偏心轮couple 力偶coupling 联轴器，连接、耦合cross section 截面，横断面，剖面curvature 弯曲，曲率，弧度carriage 溜板center distance 中心距，顶尖距chip 切削、切、削cold-roll冷轧、冷轧机clutch抓住、捏紧、离合器compound rest 小刀架casting 铸造，铸件dynamics 动力学，动力特性die 模切，模具、冲模、压模displacement 位移drawing 绘图，制图deburr 去毛刺，去飞翅durable耐用的、耐久的、坚固的deflection偏转、偏差deformation 变形，形变，扭曲，应变engagement啮合、吃刀量free-body 自由体，隔离体free-body diagram隔离体受力图follower 从动轮，随动机构、从动件facing 车平面，端面加工feed rod 光杠forge锻造、打制、锻工车间feed motion 进给运动feed per tooth 每齿进给量flexible coupling弹性联轴器、gear 齿轮，齿轮传动装置gear box齿轮箱、变速箱geometric ratio 等比headstock 主轴箱，动力箱inertia 惯性，惯量，惰性in-process （加工，处理）过程中的journal bearing 滑动轴承，向心滑动轴承knob 旋钮key键keyway键槽kinematic 运动的，运动学的kinematic pair 运动副linkage 连杆机构，低副运动链、连接lever 杠杆，手柄leadscrew 丝杠mating surface 啮合表面，接触面moment 力矩momentum 动量plasmas 等离子piston 活塞，柱塞primary motion 主运动prototype 原型，模型机、样机pulley 滑轮，皮带轮quill 活动套筒，空心轴，钻轴、衬套runout 偏斜，径向跳动reaming 铰孔reversal 颠倒、相互、反向、改变方向statics 静力学，静止状态shaft 轴scalar 数量（的），标量（的）sketch 草图，简图、示意图、设计图sawing 锯，锯切，锯开stem 杆、棒、柄、柱、轴socket wrench 套筒扳手slider-crank mechanism曲柄滑块机构shaft bearing 轴承stress concentration 应力集中screw driver 螺丝刀turning 旋转，车削，车外圆tailstock尾座，尾架torque转矩、扭矩、扭转vector 矢量、向量vector 矢量，向量workpiece 工件。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
组装、冲压、喷漆等专fit together 组装在一起业词汇fasten 锁紧 (螺丝 )fixture 夹具 (治具 ) Assembly line 组装线pallet 栈板Layout 布置图barcode 条码Conveyer 流水线物料板barcode scanner 条码扫Rivet 柳丁 table 拉钉机描器Rivet gun 拉钉枪fuse together 熔合Screw driver 起子fuse machine 热熔机Electric screw driver 电repair 修理动起子operator 作业员Pneumatic screw driver QC(quality control) 品管气动起子质量控制worktable工作桌supervisor 课长OOBA（ out of box audit ）ME 制造工程师开箱检查MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板 chassis基座 bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP(standard operatingprocedures)制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resourcedepartment人力资源部production department 生lathe 车床factory director 厂长产部门planer |'plein| 刨department director 部长planning department 企划床deputy manager | =vice 部miller 铣床manager 副理QC Section 品管科grinder 磨床section supervisor 课长stamping factory 冲压厂driller?? 床deputy section supervisor painting factory 烤漆厂linear cutting 线切割=vice section superisor 副molding factory 成型厂electrical sparkle 电火花课长common equipment 常用welder 电焊机group leader/supervisor 设备staker=reviting machine组长uncoiler and straightener铆合机line supervisor 线长整平机position 职务assistant manager助理punching machine 冲床president 董事长to move, to carry, to robot 机械手general manager 总经理handle 搬运hydraulic machine 油压special assistant manager be put in storage 入库机特助pack packing 包装to apply oil 擦油 tofile burr 锉毛刺 final inspection 终检to connect material 接料to reverse material 翻料wet station 沾湿台 Tiana 天那水 cleaning cloth 抹布to load material 上料 to unload material 卸料 to return material/stock to 退料scraped |'skræpid| 报废scrape ..v.刮 ;削deficient purchase 来料不良stamping-missing 漏冲manufacture procedure 制production capacity 生产程力deficient manufacturing education and training教procedure 制程不良育与训练oxidation|'proposal improvement提ksi'dein| 氧化案改善scratch 刮伤spare parts=buffer 备件dents 压痕forklift 叉车defective upsiding down trailer=long vehicle 拖板抽芽不良车defective to staking 铆合compound die 合模不良die locker 锁模器embedded lump 镶块pressure plate=plate feeding is not in place 送pinch 压板料不到位bolt 螺栓name of a department 部pedal 踩踏板门名称stopper 阻挡器administration/general flow board流水板affairs dept 总务部hydraulic handjack 油压automatic screwdriver 电板车动启子forklift 叉车thickness gauge 厚薄规pallet 栈板gauge(or jig) 治具glove(s)手套power wire 电源线glove(s)with exposed buzzle 蜂鸣器fingers 割手套defective product label 不thumb 大拇指良标签forefinger食指identifying sheet list 标示midfinger 中指单ring finger无名指screwdriver holder 起子little finger小指插座band-aid 创可贴iudustrial alcohol 工业酒magnetizer 加磁器not up to standard 不合规burr( 金属 )flash( 塑件 )毛精lamp holder 灯架格边alcohol container 沾湿台to mop the floor 拖地dimension/size is a little poor staking 铆合不良head of screwdriver 起子to clean the floor 扫地bigger 尺寸偏大 (小 )excesssive gap间隙过大头to clean a table 擦桌子cosmetic defect 外观不良grease/oil stains 油污sweeper 扫把air pipe 气管slipped inclusion 杂质mop 拖把packaging tool 打包机screwhead/slippery screw painting peel off 脏污vaccum cleaner 吸尘器packaging 打包head 螺丝滑头shrinking/shrinkage 缩水rag 抹布missing part 漏件slipped mixed color 杂色garbage container 灰箕wrong part 错件screwhead/shippery scratch 划伤garbage can垃圾箱excessive defects 过多的screw thread 滑手poor processing 制程不garbage bag 垃圾袋缺陷speckle 斑点良chain 链条critical defect 极严重缺mildewed=moldy=mould poor incoming part 事件jack 升降机陷y 发霉不良production line 流水线major defect 主要缺陷rust 生锈fold of pakaging belt 打chain 链条槽minor defect 次要缺陷deformation 变形包带折皱painting make-up 补漆enterprise expansion up-to-grade products 良basket 蝴蝶竺discoloration 羿色projects 企划品plastic basket 胶筐water spots 水渍QC 品管defective products, not isolating plate baffle plate; polishing/surface die worker 模工up-to-grade products 不barricade 隔板processing 表面处理production, to produce 生良品carton box 纸箱exposed metal/bare metal产waste 废料to pull and stretch 拉深金属裸露equipment 设备board 看板to put material in place, lack of painting 烤漆不to start a press 开机feeder 送料机to cut material, to input 到位stop/switch off a press 关sliding rack 滑料架落料safety 安全机defective product box 不to impose lines 压线quality 品质classification整理良品箱to compress, compressing delivery deadline 交货期regulation 整顿die change 换模压缩cost 成本cleanness清扫to fix a die 装模character die 字模engineering 工程conservation 清洁to take apart a die 拆模to feed, feeding 送料die repair 模修culture 教养to repair a die 修模transportation 运输enterpriseplan=qualified products,packing material 包材(be)qualfied, up to grade合格not up to grade, not qualified 不合格material change, stock change 材料变更feature change 特性变更evaluation 评估prepare for,make preparations for 准备parameters 参数production unit 生产单位lots of production 生产批量steel plate 钢板 rollmaterial 卷料 manufactureprocedure 制程operation procedure 作业流程to revise, modify 修订stage die 工程模punch press, dieing outautomation 自动化press 冲床to stake, staking, reviting uncoiler & strainghtener铆合整平机add lubricating oil加润feeder 送料机滑油rack, shelf, stack 料架shut die 架模cylinder 油缸shut height of a die架模robot 机械手高度taker 取料机analog-mode device 类模conveyer belt 输送带rotating speed, revolution to switch over to,转速switch---to throw--over manufacture management switching over 切换制造管理engineering,project abnormal handling 异常difficulty处理工程瓶颈器transmission rack 输送架die lifter 举模器top stop 上死点argon welding 氩焊bottom stop 下死点vocabulary for stamping one stroke 一行程冲压常词汇inch 寸动stamping, press 冲压to continue, cont. 连动to grip(material) 吸料processing, to process 加to notice 通知具location lump,locating工application formfor to load a die 装上模具piece, block stop定位块delivery, to deliver 交货purchase 请购单to tight a bolt 拧紧螺栓reset 复位to return delivenry to.consume, consumption 消to looser a bolt 拧松螺栓smoothly 顺利to send delinery耗to move away a die plate dent 压痕back to fill in 填写移走模板scratch 刮伤to retrn of goods 退abrasion 磨损easily damaged parts 易deformation 变形货reverse angle = chamfer损件filings 铁削registration 登记倒角standard parts 标准件to draw holes 抽孔registration card 登记卡character die 字模breaking.(be)broken,(be) inquiry, search for 查寻to control 管制to collect, to gather 收集cracked 断裂to stock, storage, in stock to put forward and hand failure, trouble 故障to lubricate 润滑库存in 提报statistics 统计common vocabulary for receive 领取safe stock 安全库存demand and supply 需求die engineering approval examine and acceptance =receive 验career card 履历卡模具工程常用词汇verify 审核收to take apart a die 卸下模die 模具figure file, chart file 图档cutting die, blanking die 冲裁模progressive die, follow (-on)die连续模compound die 复合模punched hole 冲孔panel board 镶块to cutedges=sidecut=side scrap 切边to bending 折弯to pull, to stretch 拉伸Line streching, line pulling 线拉伸 engraving, to engrave 刻印upsiding down edges 翻边to stake 铆合designing, to design 设计design modification 设计变化die block 模块folded block 折弯块sliding block 滑块location pin 定位销lifting pin 顶料销die plate, front board 模板padding block 垫块stepping bar 垫条upper die base上模座first check 初盘复棹人lower die base 下模座second count 复盘人upper supporting blank second check 复盘复核上承板人upper padding plate equipment 设备blank 上垫板waste materials 废料spare dies模具备品work in progress productspring弹簧在制品bolt 螺栓casing = containerazationdocument folder 文件夹装箱file folder资料夹quantityof physicalto put file in order 整理invetory second count 复资料盘点数量spare tools location 手工quantity of customs count备品仓会计师盘 ,点数量first count初盘人the first page 第一联filed by accounting department for reference 会计部存查end-user/usingunit(department) 使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name 单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial mold 成型distribution department department)material for engineering分发单位本表请与盘点清册一起mold testing 工程试模材location 地点送会计部－ (NHK厂区料chairman 主席送财会部 )not included in physical present members 出席人Application status inventory 不列入盘点员records ofyear-end sample 样品subject 主题physical inventory List incoming material to be conclusion 结论and inspected 进货待验decision items 决议事项physical inventory card description 品名responsible department 年终盘点卡与清册使用steel/rolled steel 钢材负责单位－状况明细表material statistics sheet pre-fixed finishing date blank and waste sheet物料统计明细表预定完成日NO.meeting minutes 会议记approved by / checked by 空白与作废单号录/ prepared by 核准 /审核 / plate 电镀meeting type 会别承办PCE assembly production available material 良品可year-end physical packing materials 包材schedule sheet使用inventory difference good product/accepted PCE 组装厂生产排配表obsolete material 良品已analysis sheet goods/accepted model 机锺呆滞年终盘点差异分析表parts/good parts 良品work order 工令to be inspected or physical inventory 盘点defectiverevision 版次reworked数量product/non-good parts remark 备注待验或重工physical count quantity不良品production control total 合计帐面数量disposed goods 处理品confirmation 生产确认cause description 原因说difference quantity 差异warehouse/hub 仓库checked by 初审明量on way location 在途仓approved by 核准part number/ P/N 料号cause analysis原因分析oversea location 海外仓department 部门type 形态raw materials 原料spare parts physical stock age analysis sheet item/group/class 类别materials 物料inventory list备品盘点库存货龄分析表quality 品质finished product 成品清单on-hand inventory现有prepared by 制表semi-finished product 半spare molds location 模库存notes 说明成品具备品仓skid/pallet 栈板feature die 公母模active plate 活动板phosphate 皮膜化成tox machine 自铆机expansion dwg 展开图baffle plate 挡块viscosity 涂料粘度wire EDM 线割radius 半径cover plate 盖板alkalidipping 脱脂EDM 放电机shim(wedge) 楔子male die 公模main manifold 主集流脉coil stock 卷料torch-flame cut 火焰切割female die 母模bezel 斜视规sheet stock 片料set screw 止付螺丝groove punch 压线冲子blanking 穿落模tolerance 工差form block 折刀air-cushion eject-rod 气dejecting 顶固模score=groove 压线stop pin 定位销垫顶杆demagnetization 去磁 ;消cam block 滑块round pierce punch=die spring-box eject-plate 弹磁pilot 导正筒button 圆冲子簧箱顶板high-speed transmission trim 剪外边shape punch=die insert 异bushing block 衬套高速传递pierce 剪内边形子insert 入块heat dissipation 热传drag form 压锻差stock locater block 定位club car 高尔夫球车rack 上料pocket for the punch head块capability 能力degrease脱脂挂钩槽under cut=scrap chopper parameter 参数rinse 水洗slug hole 废料孔清角factor 系数alkaline etch 龄咬desmut 剥黑膜assembly 组装dryer 烘干机cold slug 冷块D.I. rinse 纯水次stamping 冲压induction 感应blush 导色Chromate 铬酸处理molding 成型induction light 感应光gouge 沟槽 ;凿槽Anodize 阳性处理spare parts=buffer 备品response=reaction=intera satin texture 段面咬花seal 封孔coordinate 座标ction 感应witness line 证示线revision 版次dismantle the die 折模ram 连杆patent 专利part number/P/N 料号auxiliary fuction 辅助功edge finder 巡边器grit 沙砾good products 良品能concave 凸granule=peuet=grain 细scraped products 报放心poly-line多义线convex 凹粒品heater band 加热片short 射料不足grit maker 抽粒机defective products 不良thermocouple 热电偶nick 缺口cushion 缓冲品sand blasting 喷沙speck 瑕 ??magnalium 镁铝合金finished products 成品grit 砂砾shine 亮班magnesium 镁金disposed products 处理品derusting machine 除锈splay 银纹metal plate 钣金barcode 条码机gas mark 焦痕lathe 车flow chart 流程表单degate 打浇口delamination 起鳞mill 锉plane 刨度现状volatile 挥发性forming 成型 (抽凸 ,冲凸 ) grind 磨torque 扭矩resistance电阻draw hole 抽孔drill 铝spline=the multiple keys ion 离子bending 折弯boring 镗花键titrator 滴定仪trim 切边blinster 气泡quenching 淬火beacon 警示灯emboss 凸点fillet 镶 ;嵌边tempering 回火coolant 冷却液dome 凸圆through-hole form 通孔annealing 退火crusher 破碎机semi-shearing 半剪形式carbonization 碳化模具工程类stamp mark 冲记号voller pin formality 滚针alloy 合金plain die 简易模deburr or coin 压毛边形式tungsten high speed steel pierce die 冲孔模punch riveting 冲压铆合cam driver 铡楔钨高速的forming die 成型模side stretch 侧冲压平shank 摸柄moly high speed steel 钼progressive die 连续模reel stretch 卷圆压平crank shaft 曲柄轴高速的gang dies 复合模groove 压线augular offset 角度偏差organic solvent 有机溶剂shearing die 剪边模blanking 下料velocity 速度bracket 小磁导riveting die 铆合模stamp letter 冲字 (料号 ) production tempo 生产进liaison 联络单pierce 冲孔shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification冲床规格lifter pin 顶料销punch set 上模座die height range 适用模eq-height sleeves=spool punch pad 上垫板高等高套筒punch holder 上夹板die height 闭模高度pin 销stripper pad 脱料背板burr 毛边lifter guide pin 浮升导料up stripper 上脱料板gap 间隙销male die 公模 (凸模 ) weight 重量guide pin 导正销feature die 公母模total wt. 总重量wire spring 圆线弹簧female die 母模 (凹模 ) punch wt. 上模重量outer guiding post 外导upper plate 上模板五金零件类柱lower plate 下模板inner guiding post 内导stop screw 止付螺丝die pad 下垫板柱located pin 定位销die holder 下夹板inner hexagon screw 内outer bush 外导套die set 下模座六角螺钉模板类bottom block 下垫脚dowel pin 固定销top plate 上托板（顶板）bottom plate 下托板 (底coil spring 弹簧top block 上垫脚板 )stripping plate 内外打 (脱料板 )outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块 (嵌入件 ) deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴guide plate 定位板baffle plate 挡块sliding block滑块located block 定位块sliding dowel block 滑块supporting block for固定块location active plate 活动板定位支承块lower sliding plate 下滑air cushion plate 气垫板块板air-cushion eject-rod 气upper holder block 上压垫顶杆块trimming punch 切边冲upper mid plate 上中间子板stiffening rib punch=spring box 弹簧箱stinger 加强筋冲子spring-box eject-rod 弹簧ribbon punch 压筋冲子箱顶杆reel-stretch punch 卷圆压spring-box eject-plate 弹平冲子簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块塑件 & 模具相关英文compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹two plate 两极式（模具）L=3~5mm stress crack 应力电裂flow mark 流痕well type蓄料井welding line 熔合痕orientation 定向welding mark 溶合痕insulated runner 绝缘浇eject pin 顶出针sprue gate 射料浇口，直post screw insert 螺纹套道方式knock pin 顶出销浇口筒埋值hot runner 热浇道return pin 回位销反顶针nozzle 射嘴self tapping screw 自攻runner plat 浇道模块sleave 套筒sprue lock pin 料头钩销螺丝valve gate 阀门浇口stripper plate 脱料板(拉料杆 )striper plate 脱料板band heater 环带状的电insert core 放置入子slag well 冷料井piston 活塞热器runner stripper plate 浇道side gate 侧浇口cylinder 汽缸套spindle 阀针脱料板edge gate侧缘浇口chip 细碎物spear head刨尖头guide pin 导销tab gate 搭接浇口handle mold 手持式模具slag well 冷料井eject rod (bar)（成型机）film gate 薄膜浇口移转成型用模具cold slag 冷料渣顶业捧flash gate 闸门浇口encapsulation molding 低air vent 排气道subzero 深冷处理slit gate 缝隙浇口压封装成型h=0.02~0.05mm three plate 三极式模具fan gate 扇形浇口射出成型用模具w=3.2mm runner system 浇道系统dish gate 因盘形浇口H=F=1/2t~1/5t品质人员名称类T=2.5~3.5mm QC quality control diaphragm gate 隔膜浇口品质管理人员ring gate 环形浇口FQC final quality subarine gate 潜入式浇control终点品质管制口人员tunnel gate 隧道式浇口IPQC in process pin gate 针点浇口quality control制程中Φ 0.8~1.0mm的品质管制人员Runner less 无浇道OQC output quality (sprue less)无射料control最终出货品质管方式管制人员long nozzle 延长喷嘴方IQC incoming quality 式control进料品质管制sprue 浇口 ;溶渣人员TQC total quality control全面质量管理POC passage qualitycontrol段检人员QA quality assurance质量保证人员OQA output qualityassurance出货质量保证人员QE quality engineering品质工程人员品质保证类FAI first articleinspection新品首件检查FAA first articleassurance首件确认TVR tool verificationreport模具确认报告3B 3B模具正式投产前确认CP capability index能力指数CPK capability indexof process模具制程能力参数SSQA standardizedsupplier quality合格供应商品质评估OOBA out of box audit开箱检查QFD quality functiondeployment品质机能展开S/S Sample size 抽样Military-Standard军用FMEA failure model检验样本大小标准effectiveness analysis ACC Accept允收S I-S IV Special 失效模式分析REE Reject拒收I-Special IV特殊抽样8 disciplines8 项回CR Critical极严重的水准等级复内容MAJ Major主要的P/N Part Number料FA final audit最後一MIN Minor轻微的号次稽核AOQ Average Output L/N Lot Number特CAR corrective action Quality平均出厂品质采request改正行动要求AOQL Average Output AOD Accept On corrective action report Quality Level平均出Deviation特采改正行动报告厂品质UAI Use As It首件FQC 运作类Q/R/S检查报告AQL Acceptable Quality/Reliability/Servic FPIR First Piece Quality Level运作类 e 品质 /可靠度服务Inspection Report百万允收品质水准MIL-STD分之一PPM Percent Per Million批号制程统计品管专类SPC Statistical Process Control统计制程管制SQC Statistical Quality Control统计品质管制R Range全距AR Averary Range全距平均值UCL Upper Central Limit管制上限LCL Lower Central Limit管制下限MAX Maximum最大值MIN Minimum最小质改善小组值PDCA Plan Do Check GRR Gauge Action计划执行检Reproducibility&Repeata查总结bility量具之再制性及ZD Zero Defect零缺重测性判断量可靠与否点DIM Dimension尺寸QI Quality DIA Diameter直径Improvement品质改善FREQ Frequency 频QP Quality Policy 目率标方针N Number 样品数TQM Total Quality 其它品质术语类Management全面品质QCC Quality Control管理Circle品质圈MRB Material Reject QIT Quality Bill退货单Improvement Team 品LQL Limiting Quality Level最低品质水准RMA Return MaterialAudit退料认可QAN QualityAmelionrate Notice品质改善活动ADM AbsoluteDimension Measuremat全尺寸测量QT Quality Target品质目标7QCTools7 QualityControll Tools品管七大手法通用之件类ECN EngineeringChange Notes工程变更通知 (供应商 )ECO EngineeringChange Order工程改动要求 (客户 )PCN Process ChangeNotice工序改动通知PMP ProductManagement Plan生产管制计划SIP Specification InProcess制程检验规格SOP StandardOperation Procedure制造作业规范IS InspectionSpecification成品检验规范BOM Bill Of Material 物料清单PS Package Specification包装规范SPEC Specification 规格DWG Drawing图面系统文件类QC Quality System 品质系统ES Engineering Standarization工程标准CGOO China General PCE 龙华厂文件H Huston ( 美国 )休斯敦C Compaq ( 美国 ) 康伯公司C China中国大陆A Assembly 组装 (厂) SStamping 冲压 (厂 )P Painting烤漆(厂)I Intel英特尔公司T TAIWAN台湾IWS InternationalWorkman Standard工艺标准ISO InternationalStandard Organization国际标准化组织GS GeneralSpecification一般规格CMCS C-ChinaM-Manufact C-CompaqS-Stamping Compaq 产品在龙华冲压厂制造作业规范CQCA Q-QualityA-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-PaintingCompaq 产品在龙华烤漆厂品管作业规范部类PMC Production&Material Control生产和物料控制PPC Production PlanControl生产计划控制MC Material Control物料控制ME ManafactureEngineering制造工程部PE Project Engineering产品工程部A/C Accountant Dept会计部P/A Personal&Administration人事行政部DC Document Center 资料中心QE Quality Engineering品质工程(部 )QA Quality Assurance 品质保证 (处 )QC Quality Control 品质管制 (课 )PD Product Department 生产部LAB Labratry实验室IE Industrial Engineering工业工程R&D Research&Design设计开发部P Painting烤漆(厂)A Asssembly组装(厂)S Stamping冲压(厂)生产类PCS Pieces个(根,块等)PRS Pairs 双 (对等 ) CTNCarton 卡通箱 PALPallet/skid 栈板 POPurchasing Order采购订单MO Manufacture Order生产单D/C Date Code生产日期码ID/C IdentificationCode (供应商 )识别码SWR Special WorkRequest特殊工作需求L/N Lot Number批号P/N Part Number料号其它OEM Original EquipmentManufacture原设备制造PCE PersonalComputer Enclosure个人电脑外设PC Personal Computer个人电脑CPU CentralProcessing Unit中央处理器SECC SECC`电解片SGCC SGCC热浸镀锌材料NHK NorthofHongkong中国大陆PRC People's Republicof China中国大陆U.S.A the United Statesof America美国A.S.A.P As Soon AsPossible尽可能快的C=0Critical=0极严CD Compact Disk光E-MAIL重不允许碟Electrical-Mail电子邮ESD Electry-static CD-ROM Compact 件Discharge 静电排放Disk Read-Only Memory N/A Not Applicable5S希腊语整理 ,整顿 ,只读光碟不适用清扫 ,清洁 ,教养FDD Floppy Disk QTY Quantity数量ATIN Attention知会Drive软碟机VS以及CC Carbon Copy 副HDD Hard Disk Drive REV Revision版本本复印相关人员碟碟机JIT Just In Time零库APP Approve核准 ,REF Reference仅供存认可 ,承认参考I/O Input/Output输CHK Check确认CONN Connector连入/输出AM Ante Meridian接器OK Ok好上午CAV Cavity模穴NG Not Good不行 ,PM Post Meridian 下CAD Computer Aid 不合格午Design计算机辅助设计ASS'Y Assembly装配 ,组装MAT'S Material材料IC Integrated Circuit 集成电路T/P True Position真位度TYP Type类型WDR Weekly Delivery Requitement周出货需求C?T Cycle Time制程周期L/T Lead Time前置时间 (生产前准备时间)S/T Standard Time 标hod,Time 人力 ,物力 ,财BS Brain storming脑MT Mini-Tower立式准时间务 ,技术 ,时间 (资源 )力激荡(机箱 )P/M Product Market SQA Strategy Quality EMI Electronic DVD Digital Vedio 产品市场Assurance 策略品质保Magnetion Inspect高Disk3C证磁测试VCD Vdeio Compact Computer,Commumcatio DQA Desigh Quality FMI Frequency Diskn,Consumer electronic's Assurance 设计品质保Modulatim Inspect高LCD Liquid Crystal 消费性电子证频测试Display5WIH MQA Manufacture B/M Boar/Molding(flat CAD Computer AID When,Where,Who,What,Quality Assurance制造cable)DesignWhy,How to品质保证C/P Connector of PC CAM Computer AID 5M SSQA Sales and service A/P Assembly ManufacturingMan,Machine,Material,M Quality Assurance销售SPS Switching power CAE Computer AID ethod,Measurement及服务品质保证supply 电源箱Engineering4MIH LRR Lot Rejeet Rate DT Desk Top卧式ABIOS Achanced Man,Materia,Money,Met批退率(机箱 )Basic in put/outputsystem先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor互补金属氧化物半导体PDA Personal Digital Assistant个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture工业标准体制结构MCA Micro Channel Architecture微通道结构W/H Wire Harness 金MRP Material EISA Extended属线绪束集组件Requiremcnt Planning Industry Standard F/C Flat Calle排线物料需计划Architecture扩充的工PCB Printed Circuit OC Operation System 业标准结构Board印刷电路板作业系统SIMM Single in-line CAR Correction Action TBA To Be Design memory module单项Report 改善报告待定 ,定缺导通汇流组件NG Not Good不良D/C Drawing Change DIMM Dual in-line WPR Weekly Delivery P/P Plans & Procedune Memory Module双项Requirement周出货要EMI Electrical-Music 导通汇流组件求Industry 电子音乐工业LED Light-Emitting PPM Parts Per Million RFI Read Frequency Diode发光二级管百万分之一Input读频输入FMEA Failure Mode TPM Total Production MMC Maximum Effectivenes失效模式Maintenance全面生产Material Condition分析保养MMS MaximumMaterial SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding压延成形powder metal forging粉末锻造cold chamber die casting冷式压铸precisionforging精密锻造cold forging冷锻pressforging冲锻compacting molding粉末压出成形rockingdieforging摇动锻造compound molding复合成形rotary forging回转锻造compression molding压缩成形rotationalmolding离心成形dip mold浸渍成形rubber molding橡胶成形encapsulation molding注入成形sand moldcasting 砂模铸造 extrusionmolding 挤出成形 shellcasting 壳模铸造foam forming ? 泡成形sinter forging 烧结锻造forging roll 轧锻 six sidesforging 六面锻造 gravitycasting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出) 成形squeezecasting 高压铸造hot chamber die casting热室压铸swaging 挤锻hot forging 热锻 transfermolding 转送成形injection molding 射出成形 warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mouldthermal forming对模热成形模各式模具分类用语chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模 flashmold 溢料式模具bismuth mold铋铸模冲切模landed plunger mold 有composite dies 复合模肩柱塞式模具具 manifold die 分歧管burnishing die挤光模模具landed positive mold 有counter punch反凸模肩全压式模具modular mold组合式模button die 镶入式圆形具凹模 loading shoe mold double stack mold 双层料套式模具模具 multi-cavity mold center-gated mold 中心多模穴模具浇口式模具loose detail electroformed mold 电mold 活零件模具铸成形模multi-gate extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具 plaster mold 石膏模blank through dies 漏件式落料模 porous mold通气性模具duplicated cavity plate 复板模 positive mold全压式模具fantail die 扇尾形模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具 prototype mold 雏形试验模具ingot mold钢锭模punching die 落料模lancing die切口模raising(embossing)压花起伏成形re-entrant mold 倒角式模具 sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold单腔模具solid forging die 整体锻模 split forging die拼合锻模split mold双并式模具sprueless mold无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold平刮铸模swing die 振动模具three plates mold 三片式模具 trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模模具厂常用之标准零配件air vent vale通气阀anchor pin 锚梢angular pin 角梢baffle调节阻板angular pin 倾斜梢baffle plate 折流档板 ballbutton 球塞套 ballplunger 定位球塞ball slider球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster上下模板bottom board 浇注底板bolster 垫板bottomplate 下固定板bracket托架bumperblock 缓冲块buster 堵口castingladle 浇注包casting lug 铸耳cavity模穴 (模仁 )cavity retainer plate 模穴托板center pin 中心梢clamping block锁定块coil spring螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型 core pin心die holder 母模固定板ejector guide pin 顶出导型梢die lip 模唇梢 ejector leader busher cotter 开口梢cross 十die plate 冲模板 die set顶出导梢衬套字接头冲压模座ejector pad 顶出垫cushion pin缓冲梢direct gate 直接浇口ejector pin 顶出梢diaphragm gate 盘形浇dog chuck 爪牙夹头ejector plate 顶出板口dowel定位梢 dowel ejector rod 顶出杆die approach模头料道hole 导套孔ejector sleeve 顶出衬套die bed 型底dowel pin 合模梢ejector valve 顶出阀die block 块形模体die dozzle辅助浇口eye bolt环首螺栓body 铸模座dowel pin 定位梢 draft filling core椿入蕊die bush 合模衬套die拔模锥度film gate 薄膜形浇口button 冲模母模draw bead 张力调整杆finger pin指形梢die clamper 夹模器die drive bearing 传动轴承finish machined plate 角fastener 模具固定用零ejection pad 顶出衬垫形模板 finish machined 件ejector脱模器round plate 圆形模板fixed bolster plate 固定侧模板 flanged pin 带凸缘 ?flash gate 毛边形浇口flask 上箱floating punch浮动冲头gate 浇口gate land浇口面gib 凹形拉紧 ?goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢 guide post 引导柱guide plate 导板guide rail 导轨head punch顶?冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒 hose nippler管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land合模平坦面l and area 合模面leader busher 导梢衬套lifting pin 起模顶 ? lining内衬 locatingcenter punch 定位中心冲头locating pilot pin定位导梢locating ring 定位环lock block 压块 lockingblock 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate分型板pin gate 针尖浇口 platemold base塑胶模座衬板mold clamp铸模紧固夹pre extrusion punch 顶mold platen 模用板挤冲头 punch冲头moving bolster换模保puncher 推杆pusher持装置pin衬套梢moving bolster plate 可rack机架 rapping rod动侧模板one piece起模杆casting整体铸件re-entrant mold 凹入模parallel block 平行垫块retainer pin 嵌件梢paring line分模线retainer plate托料板parting lock set合模定return pin 回位梢位器 pass guide穴型导riding stripper浮动脱模板器 ring gate 环型浇口peened head punch 镶入roller滚筒 runner流道式冲头 pilot pin导 ?runner ejector set流道顶出器runner lock pin spindle 主轴sprue 注流道拉梢道screw plug头塞set sprue bushing注道衬套screw固定螺丝sprue bushing guide 注shedder 脱模装置 shim道导套分隔片sprue lock bushing注道shoe 模座之上下模板定位衬套 sprue puller shoot流道注道拉料 ?shoulder bolt 肩部螺丝spue line合模线 square skeleton骨架key方键slag riser冒渣口square nut方螺帽slide(slide core) 滑块square thread 方螺纹slip joint滑配接头stop collar限位套 stop spacer block间隔块pin止动梢spacer ring间隔环stop ring止动环spider模蕊支架stopper 定位停止梢straight pin圆柱?stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar支撑支柱/顶出支柱support pin支撑梢supporting plate托板sweep templete 造模刮板tab gate 辅助浇口taperkey 推拔键taper pin 拔锥梢 /锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate隧道形浇口vent 通气孔wortleplate 拉丝模板模具常用之工作机械3D coordinatemeasurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床 contouring machine轮廓锯床。