夏普PC929引脚图

VO2H VO2L VO1L ICCH
Low level supply current
*7 "Low→High" threshold input current
Isolation resistance "Low→High" propagation delay time "High→Low" propagation delay time Rise time Fall time
tPCOtf
VCC = V01 = 24V, IF = 5mA
CG = 3 000pF, RG = 47Ω CP = 1 000pF, RC = 1kΩ
VCC
V
Error signal output current IFS
20
mA
*3 Total power dissipation Ptot
550
mW
*5 Isolation voltage
Viso
4 000 Vrms
Operating temperature Topr - 25 to + 80 ˚C
PC929
s Electro-optical Characteristics (1)
(Ta=Topr unless otherwise specified)
Input
Output
Parameter Forward voltage Reverse current Terminal capacitance Operating supply voltage
Protective output Overcurrent detection
*9
*10 Overcurrent detecting voltage
Overcurrent detecting voltage hysteresis width
VCTH VCHIS
Ta = 25˚C, IF = 5mA
VCC - VCC - VCC -
s Truth Table
Input ON OFF
C Input/Output Low level High level Low level High level
O2 Output High level Low level Low level Low level
FS Output High level Low level High level High level
0.5 0.5 0.5 0.5
-
-
Unit V V µA pF V V
Measuring circuit
-
-
V
(1)
V
(2)
V
(3)
µ A (4)
mA
mA
(6)
mA
mA
mA
(5)
mA
Ω
-
µs
µs
(8)
µs
µs
V/ µ s (7)
V/ µ s
Transfer characteristics Response time
Operation truth table is shown on the next page.
*1, 2, 3 Decrease in the ambient temperature range of the Absolute Max. Rating : Shown in Figs 1 and 2. *4 Pulse width <=0.15 µs, Duty ratio=0.01 *5 40 to 60% RH, AC for 1 minute, Ta=25˚C
V
VCC = V01 = 24V, RG = 47Ω
6.5 6.0 5.5
CG = 3 000pF, FS = OPEN
1
2
3
V
(9)
*9
O2 "High→Low" delay time at protection from overcurrent
tPCOHL
Ta = 25˚C
-
4
10
µs
O2 fall time at protection from overcurrent
Ta = 25˚C, VCC = VO1 = 24V RG = 47Ω , CG = 3 000pF, IF = 5mA
*8
Ta = 25˚C, VCC = VO1 = 24V, IF = 5mA VCM = 600V(peak ), ∆ VO2H = 2.0V *8
Ta = 25˚C, VCC = VO1 = 24V, IF = 0mA VCM = 600V(peak ), ∆ VO2L = 2.0V *8
For protective operation
PC929
s Electro-optical Characteristics (2)
(Ta=Topr unless otherwise specified)
Parameter
Symbol
Conditions
MIN. TYP. MAX. Unit Test circuit
Amp.
1 2 3 4 5 67
1 Cathode 2 Cathode 3 Anode 4 NC 5 NC 6 NC 7 NC
8 FS
9C
10 GND
11 O2 12 O1 13 VCC 14 GND
Terminals 4 to 7 : Shortcircuit in element
* "OPIC" (Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and signal processing circuit integrated onto a single chip.
Symbol VF1 VF2 IR Ct
VCC
O1 low level output voltage
O2 high level output voltage O2 low level output voltage O leak current High level supply current
VO1L
MIN. 1.2 15 15
-
20
0.3 0.2 5 x 1010 -
- 1 500
1 500
TYP. 1.6 1.5 30 -
0.2
22
1.2 10 11 1.5 1 x 1011 0.3 0.3 0.2 0.2
-
-
MAX. 1.75
10 250 30 24
0.4
-
2.0 500 17 19 18 20 3.0 5.0
12 - 1.27
0.35
1.0
1.0
10.0
Internal connection diagram
s Absolute Maximum Ratings (Ta=Topr unless otherwise specified)
Parameter
Symbol Rating Unit
*1 Forward current Input
s Features 1. Built-in IGBT shortcircuit protector circuit 2. Built-in direct drive circuit for IGBT drive
(Peak output current ... IO1P, IO2P : MAX. 0.4A) 3. High speed response (tPLH, tPHL : MAX. 0.5 µ s) 4. High isolation voltage (Viso : 4000Vrms) 5. Half lead pin pitch (p=1.27 mm) package type 6. Recognized by UL, file NO. E64380
s Outline Dimensions
14 13 12 11 10 9 8
PC929
Primary side mark
1234567
6.5
(Unit : mm)
s Application 1. IGBT control for inverter drive
9.22
7.62
0.26
3.5
14 - 0.6
IO1 = 0.1A, IF = 5mA
*8
VCC = VO1 = 24V, IO2 = - 0.1A
IF = 5mA
*8
VCC = VO1 = 24V, IO2 = 0.1A, IF = 0mA *8
Ta = 25˚C, VCC = VO1 = 35V, IF = 0mA *8
Ta = 25˚C, VCC = VO1 = 24V, IF = 5mA *8
0.4
A
Output O1 output voltage
VO1
35
V
*2 Power dissipation
PO
500
mW
Overcurrent detecting voltage VC
VCC
V
Overcurrent detecting current IC
30
mA
Error signal output voltage VFS
“ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.”