POLYONE ECCOH 5500-1C TDS01 2013-10 EN

We recommend you not to exceed melting temperature of 170°C (338°F) ECCOH™5500/1C is a formulation allowing PVC/PE extruders to be used. Melt temperature: keep the extrusion melts temperature below 165°C (329°F) and do not exceed 170°C (338°F). Screw and head: Low compression screw and head are recommended, CR 1:1,2 Screw pack and breaker plate are normally not required. Screw cooling is not required. For special extruder or application, please contact PolyOne for detailed processing information. Pre-Drying Our formulation is supplied in aluminium foil lined bags or octa-boxes and, providing the packaging has not been disturbed, the formulation does not require pre-drying. If the formulation has been stored in a moist environment over a long period then Pre-drying at approximately 70°C (158°F) for 4 hours is recommended in dehumidifying dryers. Colorability ECCOH™5500/1C is a colourable formulation. A full range of polymer specific colour master-batches are available for ECCOH™ solutions within PolyOne. PolyOne advises customers to conduct a full homologation program on their final cable construction to confirm acceptability.
NES 713 IEC 60754-2
IEC 60332-3 IEC 61034 Test Method IEC 60250 (ASTM D150) IEC 60250 (ASTM D150)
14 15
Typical Value(Imperial)
Typical Value (SI)
cm
1.0 x 10 2.0 x 10
1 ° ° °
Halogen content Smoke density -Flaming mode(1mm) Ds max -Non Flaming mode(1mm) Ds max Toxicity Acid Gas Emission pH Conductivity (max) Vertical burning test Smoke density Electrical Properties Dielectric constant 50Hz (23°C-50%HR) Dissipation factor 50Hz (23°C-50%HR) Volume resistivity (23°C-50%HR) Surface resistivity (23°C-50%HR) 1 measured on type IV specimen 2 depending on cable construction
Technical Data sheet
edition 01, 2013-10
ECCOH 5500/1C
Product Description ECCOH™ 5500/1C is a low smoke and fume flame retardant non halogen solution. This product is designed for sheathing for power and telecom cable. This solution exhibits a remarkable processing performance with good mechanical properties.
cm
IEC 60093 (ASTM D257) IEC 60093 (ASTM D257)
1/2
Technical Data sheet
edition 01, 2013-10
ECCOH 5500/1C
Other properties Heat shock 1h at 150°C Shrinkage 1h at 100°C Typical Value(Imperial) pass 1.5% Typical Value (SI) pass 1.5% Test Method IEC 60811-3-1 IEC 60811-1-3
14 15 2 2 3
Typical Value (SI) 1.49 g/cm 28 55 Typical Value (SI) 12.0 MPa 104% 220% 91% 9 N/mm 15% pass pass Typical Value (SI) 35% 0 60 180 1 5.2 5.5 µS/mm Pass Pass 4.7 0.006
Copyright © 2009, PolyOne Corporation. PolyOne makes no representations, guarantees, or warranties of any kind with respect to the Information contained in this document about its accuracy, suitability for particular applications, or the results obtained or obtainable using the information. Some of the Information arises from laboratory work with small-scale equipment which may not provide a reliable indication of performance or properties obtained or obtainable on larger-scale equipment. Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for p roperty ranges and min/max specifications. Processing conditions can cause material properties to shift from the values stated in the Information. PolyOne makes no warranties or guarantees respecting suitability of either PolyOne’s products or the Information for your process or end -use application. You have the responsibility to conduct fullscale end-product performance testing to determine suitability in your application, and you assume all risk and liability arising from your use of the Information and/or use or handling of any product. POLYONE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, either with respect to the Information or products reflected by the Information. This data sheet shall NOT operate as permission, recommendation, or inducement to practice any patented invention without permission of the patent owner.
2 2 3
Test Method ISO 1183-1 (ASTM D792) ISO 1133, (b) DIN53523 (ASTM D1646) ISO R 868 (ASTM D2240) Test Method IEC 60811-1-1 IEC 60811-1-2 IEC 60811-1-1 IEC 60811-1-2 BS 6469:99-1 IEC 60811-3-1 UL 2556 IEC 60811-1-4 Test Method ISO 4589-2(ASTM D2863) IEC 60754-1 ASTM E-662
General Material Status Regional Availability Features
Uses Forms
Commercial Active Asia Pacific Non Halogen Low Smoke generation Low Toxicity &low corrosivity Environmentally friendly Wire&Cable Pellets
CONTACT INFORMATION
Americas U.S. – Avon Lake, Ohio +1 440 930 1000 Brasil – Campinas +55 19 3206 0561 ASIA China – Shanghai +86 (0) 21 5080 1188 India – Mumbai +91 22 2564 0750 +91 9820 194 220 Europe Belgium – Assesse +32 (0) 830 660 211
Retention after heat ageing 7d at Leabharlann Baidu13°C(UL Oven)
Typical Value(Imperial) 1.49 g/cm 28 55 Typical Value(Imperial) 1740 psi 104% 220% 91% 15% pass pass Typical Value(Imperial) 35% 0 60 180 1 5.2 5.5 µS/mm Pass Pass 4.7 0.006 1.0 x 10 2.0 x 10
Recommended processing parameters
Extrusion Zone 1 Temparature (Imperial) Temperature (SI) 239°F 115°C Cylinder Temperatures Zone 2 248°F 120°C Zone 3 266°F 130°C Zone 4 275°F 135°C Zone 5 302°F 150°C Adapter 311°F 155°C Head 320°F 160°C Die 329°F 165°C
4.4 g/10min
4.4 g/10min
Elongation at break 250mm/min
Retention after heat ageing 7d at 113°C(UL Oven)
Tear Strength, 23°C Hot pressure test 6h at 90 C Heat deformation 1h at 100 C,500g Cold elongation -25 C Flammability Oxygen index

Good Flame retardant Excellent processing Very Low Shrinkage
Technical Properties
Physical Properties Density, 23°C MFR (150°C/21.6kg) Mooney viscosity, ML (1+4) 140°C Hardness Shore D 15 Second Mechanical Properties Tensile Strength 250mm/min