模具英文
模具英文单词
Mould components & AccessoriesMould base 模胚Bolts 螺栓Mould frame 模架screw 螺丝Top clamp plate 面板Stripper screw 脱料螺丝Bottom clamp plate底板 F.H.C. screw（flat head cap screw）平头螺丝Socket head sountersunk screws 平头螺丝Hot runner plate 热流道板S.H.C. screw( socket head cap screw) 杯头螺丝Runner plate 水口板hexagonal socket head cap screw 杯头螺丝A plate A板 Hexagonal head screw 六角头螺丝B plate B板 Grub screw 无头螺丝（等高螺丝，基米螺丝）Stripper plate 推板Ball screw 波仔螺丝Support plate 支撑板Shoulder screw 限位螺丝（带肩螺丝，塞打螺丝）Spacer plate 方铁latch 插销Ejector retainer plate 顶针面板baffle 隔水片Ejector plate 顶针板plugs 喉塞Insulating plate 隔热板Jiffy plugs 喉咀Cavity 前模o-ring 密封圈Cavity insert 前模镶件Cooling tube 散热管Core 后模spring 弹簧Core insert 后模Support pillar 撑头Slide 行位Stop pin 垃圾钉Slide insert 行位镶件Dowel pin 管钉jaw 行位压块Spacer ring/washer 间隙圈Slide wear plate 行位耐磨块Venting slots 排气槽Slide guide block 行位导向块thermocouple 电热偶Slide lock 行位锁/行位扣Thermocouple connector 接线盒Wedge block 铲机Limit switch 限位开关W.B. wear plate 铲机耐磨块probe 探针Core pin 镶针Pry bar slots 开模槽Angle pin 斜导柱Safety strap 模锁Angle lifter 斜顶Lifting eye bolt 吊环（方向已固定）Lifter guide block 斜顶导向块Hydraulic cylinder 油缸Lifter base 斜顶座Air cylinder 气缸Press block 模料挤紧块Hydraulic motor 马达hoist ring 吊环（可转动方向）Knock out hole 顶棍孔Parting lock 树脂开闭器（尼龙扣）Name plate 铭牌Straight side interlocks T型锁（直身锁）Date code 日期印Tapered interlocks 斜度锁Cavity number 模穴号sensor 感应器engrave 刻字/凹入heater 加热器Raised out 凸出K.O. insert 顶棍孔镶件Gate type & runnerDrop gate 点水口Sprue bushing 唧嘴Pin point gate 细水口Sprue/gate 浇口Edge/side gate 边水口Center sprue/sprue gate 中心进胶/直浇口runner shut off 流道开关/转水口Sub gate 潜水口Runner lock pin 水口扣针Tunnel gate 隧道浇口Puller 拉钩Ring gate 环形浇口Sprue lock pin 拉料杆Fan gate 扇形浇口Slag well 冷料井Valve gate 针阀式水口Banana gate 香蕉水口Guide＆Locating systemGuide pin/leader pin 导柱Grinder研磨机Crane 天车（吊车）Guide bushes 导套Grinding machine 磨床 Groover machine 开槽机locating ring 法兰Lathe machine 车床Radial drill摇臂钻床EGB( ejector guide bush) 中托司Milling machine 铣床Wire cut machine 线割机Ejecting systemEjector pin 顶针Gear 齿轮Stepped ejector pin 有托顶针Rack 齿条Blade ejector 扁顶针Bearing 轴承Ejector bar 顶块Roller bearings 滚珠轴承Sleeve 司筒Retraction spring 复位弹簧Stripper plate 推板Return pin 回针Unscrewing 脱螺纹Two-stage ejector 二次顶出Ejector retainer plate 顶针面板chain 链条Ejector plate 顶针板Chain wheel 链轮Stop block 限位块key 键Ejector bushes 顶针套Specification of Injection Moulding MachineDiameter of the location ring 法兰直径Nozzle radius 机嘴半径Nozzle injection hole diameter 机嘴注射孔直径Depth for the nozzle into the mould 机嘴进入模具的深度KO hole distance KO孔间距fine thread 细螺纹Rough thread 粗螺纹mould opening distance 开模距离mould thickness 模具厚度tie bar distance Tie Bar 距离Injection defectsflash 披锋Warpage/deformation 变形Ejected mark 顶白Step 断差/台阶Weld line 熔接线Short shots 短胶Sink mark 缩水Sharp corner 尖角Gas trapped 困气Sharp edge 尖边Scratch marks 拖花Air bubble 气泡Kiss off 碰穿Short shot 短射(欠充填)Shut off 擦穿位Flow mark 流纹Sticking cavity 粘前模Sticking core 粘后模Mould designplastic 胶位radius 半径Draft angle 拔模角Diameter 直径Fillet/ inside radius 圆角Inner diameter/I.D. 内径Outside radius 外转角Outer diameter/O.D. 外径Sprue bush radius 机嘴球半径boss 柱位Corner radius 转角半径Rib 骨位Part drawing 产品图hole 孔Mould drawing 模图Pre-hardened steel 预硬钢Plastic material 胶料Through hardened steel 全硬钢Parting line 分型面Filling uneven 走胶不平衡Plastic thickness 胶厚Balanced runner 平衡水口系统Shrinkage rate 缩水率Cycle time 循环周期Surface treatmentEDM 火花纹Demoulding polish 脱模抛光High polish 高抛光Medium polish 中抛光Optical/mirror polish 镜面抛光chrome 镀铬Texture 蚀纹。
（精编）模具注塑术语中英文对照
（精编）模具注塑术语中英文对照(精编)模具注塑术语中英文对照根据国家标准，以下为部分塑料模具成形术语的标准翻译。
动模MovableMouldMovingHalf定模座板FixedClampPlateTopClampingPlateTopPlate动模座板MovingClampPlateBottomClampingPlateBottomPlate上模座板UpperClampingPlate下模座板LowerClampingPlate凹模固定板Cavity-retainerPlate 型芯固定板MouldCore-retainerPlate凸模固定板Punch-retainerPlate模套DieBodyDieSleeveDieBlank支承板BackingPlateSupportPlate垫块SpacerParallel支架EjectorHousingMouldBaseLeg模头DieHead模具分类8InjectionMold注塑模PlasticRubberMould塑胶模RubberMolding橡胶成形HotChamberDieCasting热室压铸SandMoldCasting砂模铸造ExtrusionMold挤出模Multi-CavityMold多模穴模具PalletizingDie叠层模PlasterMold石膏模ThreePlatesMold三板模PlainDie简易模PierceDie冲孔模FormingDie成型模ProgressiveDie连续模GangDies复合模ShearingDie剪边模CavityDie型腔模RivetingDie铆合模CompressionMolding压缩成型FlashMold溢流式模具ExtrusionMold挤压式模具SplitMold分割式模具MouldCavity型腔母模MoldCore模芯公模LargeDieMold大型模具PreciseDieMold 精密模具ComplexDieMold复杂模具FoamingMould发泡模具MetalDie金属模具PlasticMold塑料模具ToolStampingDiePunchDie冲压模具ExtrusionDie挤压模具GraphiteDie石墨模具流道浇口部分RunnerSystem浇道系统SprueColdMaterialTrap浇道冷料井SpruePuller拉杆RunnerDesign流道设计MainRunner主流道SecondaryRunner 次流道MouldGateDesign浇口设计SubmarineGate潜伏浇口TunnelGate隧道式浇口PinpointGate点浇口FanGate扇形浇口SideGate侧浇口EdgeGate侧缘浇口TabGate 搭接浇口FilmGate薄膜浇口FlashGate闸门浇口SlitGate缝隙浇口DishGate盘形浇口DiaphragmGate隔膜浇口RingGate环形浇口Runnerless无浇道Sprueless无射料管方式LongNozzle延长喷嘴方式Sprue浇口，溶渣Insulated/HotRunner热浇道RunnerPlat 浇道模块ValveGate阀门浇口SlagWell冷料井ColdSlag冷料渣SprueGate射料浇口Nozzle 射嘴SprueLockPin料头钩销（拉料杆）注塑缺陷Flash飞边Warpage翘曲AirTrap积风Blush发赤FlowLine流痕Splay银纹ShortShot 短射SinkMark缩痕Streak条纹Void缩孔WeldLine熔接线GasMark烧焦ColdSlug冷斑Delamination起皮Burr毛刺FlawScratch刮伤Gloss光泽Glazing光滑SurfaceCheck表面裂痕Hesitation迟滞注塑工艺MoldingConditions成型条件Drying烘干BarrelTemperature 料筒温度MeltTemperature熔化温度MoldTemperature模具温度InjectionPressure注塑压力BackPressure背压InjectionSpeed注塑速度ScrewSpeed螺杆转速TensileStrength抗拉强度T ensileElongation延伸率FlexuralModulus弯曲模FlexuralStrength抗弯强度Shrinkage收缩率RegrindUsage次料使用Moulding模塑机械设备Lathe车床Planer刨床Miller/MillingMachine铣床Grinder磨床Driller钻床LinearCutting线切割ElectricalSparkle电火花Welder电焊机PunchingMachine冲床Robot机械手CommonEquipment 常用设备EDMElectronDischargeMachining放电加工3DCoordinateMeasurement三次元量床BoringMachine搪孔机ContouringMachine轮廓锯床CopyGrindingMachine仿形磨床CylindricalGrindingMachine外圆磨床DieSpottingMachine合模机EngravingMachine 雕刻机EngravingE.D.M雕模放置加工机FormGrindingMachine成形磨床GraphiteMachine石墨加工机HorizontalBoringMachine卧式搪孔机HorizontalMachineCenter卧式加工制造中心InternalCylindricalMachine内圆磨床模具零件TopPlate上托板（顶板）T opBlock上垫脚PunchSet上模座PunchPad上垫板PunchHolder上夹板StripperPad脱料背板UpStripper上脱料板MaleDie公模（凸模）FeatureDie公母模FemaleDie母模（凹模）UpperMoldPlate上模板LowerMoldPlate 下模板DiePad下垫板DieHolder下夹板DieSet下模座BottomBlock下垫脚BottomPlate下托板（底板）StrippingPlate内外打（脱料板）OuterStripper外脱料板InnerStripper内脱料板LowerStripper下脱料板InnerGuidingPost 内导柱InnerHexagonScrew内六角螺钉DowelPin固定销MouldCoilSpring模具弹簧LifterPin 顶料销IsoheightSleeve等高套筒Pin销LifterGuidePin浮升导料销GuidePin导正销WireSpring圆线弹簧OuterGuidingPost外导柱StopScrew止付螺丝LocatedPin定位销OuterBush外导套Punch冲头Insert入块（嵌入件）DeburringPunch压毛边冲子GroovePunch压线冲子StampedPunch字模冲子RoundPunch圆冲子SpecialShapePunch 异形冲子BendingBlock折刀Roller滚轴BafflePlate挡块LocatedBlock定位块SupportingBlockforLocation定位支承块AirCushionPlate气垫板Air-CushionEject-rod 气垫顶杆TrimmingPunch切边冲子StiffeningRibPunchStinger加强筋冲子RibbonPunch压筋冲子Reel-stretchPunch卷圆压平冲子GuidePlate定位板SlidingBlock滑块SlidingDowelBlock滑块固定块ActivePlate活动板LowerSlidingPlate 下滑块板UpperHolderBlock上压块UpperMidPlate上中间板SpringBox弹簧箱Spring-BoxEject-rod弹簧箱顶杆Spring-BoxEjec模具技术用语各种常用模具成形方式AccurateDieCasting精密压铸PowderForming粉末成形CalendaringMolding压延成形PowderMetalForging粉末锻造ColdChamberDieCasting冷式压铸PrecisionForging 精密锻造ColdForging冷锻PressForgingstampforging冲锻CompactingMolding粉末压出成形RockingDieForging摇动锻造CompoundMolding复合成形RotaryForging回转锻造CompressionMolding压缩成形RotationalMolding离心成形DipMold浸渍成形RubberMolding橡胶成形EncapsulationMolding注入成形SandMoldCasting砂模铸造ExtrusionMolding挤出成形ShellCasting壳模铸造FoamForming 发泡成形SinterForging烧结锻造ForgingRoll轧锻SixSidesForging 六面锻造GravityCasting重力铸造SlushMolding凝塑成形HollowBlowMolding中空（吹出）成形SqueezeCasting高压铸造HotChamberDieCasting热室压铸Swaging挤锻HotForging 热锻TransferMolding转送成形InjectionMolding射出成形WarmForging温锻InvestmentCasting精密铸造MatchedDieMethod对模成形法LaminatingMethod被覆淋膜成形LowPressureCasting低压铸造LostWaxCasting脱蜡铸造MatchedMouldThermalForming对模热成形模CloseMold合模Demould脱模脱模剂MouldUnloading开模ToolChangeRetoolingDieChanging换模MouldClamping锁模各式模具分类用语BismuthMold铋铸模LandedPlungerMold有肩柱塞式模具BurnishingDie挤光模LandedPositiveMold有肩全压式模具ButtonDie镶入式圆形凹模LoadingShoeMold料套式模具Center-GatedMold中心浇口式模具LooseDetailMold活零件模具ChillMold冷硬用铸模LooseMold活动式模具ColdHobbing冷挤压制模法LouveringDie百叶窗冲切模CompositeDies复合模具ManifoldDie分歧管模具CounterPunch反凸模ModularMold组合模具DoubleStackMold双层模具Multi-CavityMold多模穴模具ElectroformedMold电铸成形模Multi-GateMold复式浇口模具ExpanderDie扩径模OffsetColdBendingDie双折冷弯模具ExtrusionDie挤出模PalletizingDie叠层模FamilyMold反套制品模具PlasterMold石膏模BlankThroughDies漏件式落料模PorousMold通气性模具DuplicatedCavityPlate复板模PositiveMold全压式模具FantailDie扇尾形模具PressureDie压紧模FishtailDie鱼尾形模具ProfileDie轮廓模FlashMold溢料式模具ProgressiveDie顺序模GypsumMold石膏铸模PortableMold手提式模具Hot-RunnerMold热流道模具PrototypeMold雏形试验模具原型模具IngotMold钢锭模PunchingDie落料模LancingDie切口模切缝模Raising（Embossing）压花起伏成形Re-entrantMold倒角式模具SectionalDie拼合模RunlessInjectionMold无流道冷料模具SectionalDie对合模具SegmentMold组合模Semi-PositiveMold半全压式模具Shaper 定型模套SingleCavityMold单腔模具SolidForgingDie整体锻模SplitForgingDie拼合锻模SplitMold双并式模具SpruelessMold无注道残料模具SqueezingDie挤压模StretchFormDie拉伸成形模SweepingMold 平刮铸模SwingDie振动模具ThreePlatesMold三片式模具TrimmingDie切边模UnitMold单元式模具UniversalMold 通用模具UnscrewingMold退扣式模具YokeTypeDie轭型模t-Plate弹簧箱顶板BushingBlockLinerBushing衬套CoverPlate盖板GuidePad导料块模具厂常用之标准零配件AirVentValve通气阀AnchorPin锚梢AngularPin角梢Baffle调节阻板AngularPin倾斜梢BafflePlate折流档板BallButton球塞套BallPlunger定位球塞BallSlider球塞滑块BinderPlate压板BlankHolder防皱压板BlankingDie落料冲头Bolster上下模板Bottomboard浇注底板Bolster垫板BottomPlate下固定板Bracket托架BumperBlock 缓冲块Buster堵口CastingLadle浇注包Castinglug铸耳Cavity模穴（模仁）CavityRetainerPlate模穴托板CenterPin中心梢ClampingBlock 锁定块CoilSpring螺旋弹簧ColdPunchedNut冷冲螺母CoolingSpiral螺旋冷却栓Core心型CorePin心型梢Cotter开口梢Cross十字接头CushionPin缓冲梢DiaphragmGate盘形浇口DieApproach模头料道DieBed型底DieBlock块形模体DieBody铸模座DieBush合模衬套DieButton冲模母模DieClamper夹模器DieFastener模具固定用零DieHolder母模固定板DieLip模唇DiePlate冲模板DieSet冲压模座DirectGate直接浇口DogChuck爪牙夹头Dowel定位梢DowelHole导套孔DowelPin合模梢Dozzle辅助浇口DowelPin定位梢Draft拔模锥度DrawBead张力调整杆DriveBearing传动轴承EjectionPad顶出衬垫Ejector脱模器EjectorGuidePin顶出导梢EjectorLeaderBush顶出导梢衬套EjectorPad顶出垫EjectorPin 顶出梢EjectorPlate顶出板EjectorRod顶出杆EjectorSleeve顶出衬套EjectorValve顶出阀EyeBolt环首螺栓FillingCore填充型芯椿入蕊FilmGate薄膜形浇口FingerPin指形梢FinishMachinedPlate 角形模板FinishMachinedRoundPlate圆形模板FixedBolsterPlate固定侧模板FlangedPin带凸缘针FlashGate毛边形浇口Flask上箱FloatingPunch浮动冲头Gate浇口GateLand浇口面Gib凹形拉紧楔GooseNeck鹅颈管GuideBushing引导衬套GuidePin导梢GuidePost 引导柱GuidePlate导板GuideRail导轨HeadPunch顶头冲孔HeadlessPunch直柄冲头HeavilyT aperedSolid整体模蕊盒HoseNippler管接头ImpactDamper缓冲器InjectionRam压射柱InlayBush嵌入衬套InnerPlunger内柱塞InnerPunch内冲头Insert 嵌件InsertPin嵌件梢KingPin转向梢KingPinBush主梢衬套KnockoutBar脱模杵Land 合模平坦面LandArea合模面LeaderBush导梢衬套LiftingPin起模顶针起模杆Lining内衬LocatingCenterPunch定位中心冲头LocatingPilotPin定位导梢LocatingRing定位环LockBlock压块LockingBlock定位块LockingPlate定位板LooseBush活动衬套MakingDie打印冲子ManifoldBlock歧管档块MasterPlate靠模样板MatchPlate分型板MoldBase塑胶模座MoldClamp铸模紧固夹MoldPlaten模用板MovingBolster换模保持装置MovingBolsterPlate可动侧模板OnePieceCasting整体铸件ParallelBlock平行垫块PartingLine 分模线PartingLockSet合模定位器PassGuide穴型导板PeenedHeadPunch镶入式冲头锤击强化冲头钻杆凸模PilotPin定位销导向销子PinGate针尖浇口Plate衬板PreExtrusionPunch顶挤冲头Punch冲头Puncher推杆PusherPin衬套梢Rack机架RappingRod起模杆Re-entrantMold凹入模RetainerPin嵌件梢RetainerPlate托料板ReturnPin回位梢RidingStripper浮动脱模器RingGate环型浇口Roller滚筒Runner流道RunnerEjectorSet流道顶出器RunnerLockPin流道拉梢ScrewPlug头塞SetScrew固定螺丝Shedder脱模装置Shim分隔片Shoe模座之上下模板Shoot流道ShoulderBolt肩部螺丝Skeleton骨架SlagRiser冒渣口Slide（SlideCore）滑块SlipJoint滑配接头SpacerBlock间隔块SpacerRing间隔环Spider模蕊支架Spindle主轴Sprue注道SprueBushing注道衬套SprueBushingGuide注道导套SprueLockBushing注道定位衬套SpruePuller注道拉料浇道推出杆注道残料顶销SpewLine合模线SquareKey方键SquareNut方螺帽SquareThread方螺纹LimitStopCollar限位套StopPin止动梢StopRing止动环Stopper定位停止梢StraightPin圆柱销StripperBolt脱料螺栓StripperBushing脱模衬套StripperPlate剥料板StrokeEndBlock行程止梢SubmarineGate潜入式浇口SupportPillar支撑支柱顶出支柱SupportPin支撑梢SupportingPlate托板SweepT emplate造模刮板TabGate辅助浇口TaperKey推拔键TaperPin拔锥梢锥形梢TeemingPouring浇注ThreeStartScrew 三条螺纹ThrustPin推力销TieBar拉杵TunnelGate隧道形浇口Vent通气孔WortlePlate拉丝模板模具常用之工作机械3DCoordinateMeasurement三次元量床BoringMachine搪孔机CNCMillingMachineCNC铣床ContouringMachine轮廓锯床CopyGrindingMachine仿形磨床CopyLathe仿形车床CopyMillingMachine仿形铣床CopyShapingMachine仿形刨床CylindricalGrindingMachine外圆磨床DieSpottingMachine合模机DrillingMachine钻孔机EngravingMachine雕刻机EngravingE.D.M 雕模放置加工机FormGrindingMachine成形磨床GraphiteMachine 石墨加工机HorizontalBoringMachine卧式搪孔机HorizontalMachineCenter卧式加工制造中心InternalCylindricalMachine内圆磨床JigBoringMachine冶具搪孔机JigGrindingMachine冶具磨床LapMachine研磨机MachineCenter加工制造中心MultiModelMiller靠磨铣床NCDrillingMachineNC钻床NCGrindingMachineNC磨床NCLatheNC车床NCProgrammingSystemNC程式制作系统Planer 龙门刨床ProfileGrindingMachine投影磨床ProjectionGrinder投影磨床RadialDrillingMachine旋臂钻床Shaper牛头刨床SurfaceGrinder平面磨床TryMachine试模机TurretLathe转塔车床UniversalToolGrindingMachine万能工具磨床VerticalMachineCenter立式加工制造中心WireE.D.M线割放电加工机入水Gate进入位GateLocation水口形式GateType大水口EdgeGate细水口Pin-pointGate水口大小GateSize转水口SwitchingRunnerGate唧嘴口径SprueDiameter流道MoldRunner热流道HotRunnerHotManifold温度控制器温控器ThermostatThermoregulatorsT emperatureController 热嘴冷流道HotSprueColdRunner 唧嘴直流DirectSprueGate圆形流道RoundFullHalfRunner流道电脑分析MoldFlowAnalysis流道平衡RunnerBalance热嘴HotSprue热流道板HotManifold发热管CartridgeHeater探针Thermocouples插头ConnectorPlug插座ConnectorSocket密封封料Seal运水WaterLine喉塞LinePlugThroatT aps喉管Tube塑胶管PlasticTube快速接头JiffyQuickConnectorQuickDisconnectCoupling 模具零件MoldComponents三板模3-PlateMold二板模2-PlateMold边钉导边LeaderPinGuidePin边司导套BushingGuideBushing中托司ShoulderGuideBushing中托边GuidePin顶针板EjectorRetainnerPlate托板SupportPlate螺丝Screw管钉DowelPin开模槽PlyBarScot内模管位CoreCavityinter-Lock顶针EjectorPin司筒EjectorSleeve司筒针EjectorPin推板EjectPlatePushPlateStripperPlate缩呵MovableCoreReturnCorePuller 扣机（尼龙拉勾）NylonLatchLock 斜顶Lifter模胚（架）MoldBase上内模CavityInsert下内模CoreInsert行位（滑块）Slide镶件Insert压座Wedge耐磨板油板WedgeWearPlate压条Plate撑头SupportPillar唧嘴SprueBushing挡板StopPlate定位圈LocatingRing锁扣Latch扣机PartingLockSet推杆PushBar栓打螺丝S.H.S.B顶板EjectorPlate活动臂LeverArm分流锥SprueSpreader分流板SpreaderPlate水口司Bush垃圾钉StopPin隔片Buffle弹弓柱SpringRod弹弓DieSpring中托司EjectorGuideBush中托边EjectorGuidePin镶针Pin销子DowelPin波子弹弓Ballcatch喉塞PipePlug锁模块LockPlate斜顶AnglefromPin斜顶杆AngleEjectorRod尼龙拉勾PartingLocks活动臂LeverArm复位键提前回杆EarlyReturnBar气阀Valves斜导边AnglePin术语Terms承压平面平衡PartingSurfaceSupportBalance模排气PartingLineVenting回针碰料位ReturnPinandCavityInterference 顶针碰运水WaterLineInterfereswithEjectorPin 料位出上下模PartfromCavith （Core）Side不准用镶件DoNotUse（CoreCavity）Insert 用铍铜做镶件UseBerylliumCopperInsert初步模图设计PreliminaryMoldDesign正式模图设计FinalMoldDesign弹弓压缩量SpringCompressedlength稳定性好GoodStabilityStable强度不够InsufficientRigidity均匀冷却EvenCooling扣模Sticking热膨胀ThermalExpansion公差Tolerance铜公（电极）CopperElectrode AirVentValve通气阀AnchorPin锚梢AngularPin角梢Baffle调节阻板AngularPin倾斜梢BafflePlate折流挡板BallButton球塞套BallPlunger定位球塞BallSlider球塞滑块BinderPlate压板BlankHolder防皱压板BlankingDie落料冲头Bolster上下模板BottomBoard浇注底板Bolster垫板BottomPlate 下固定板Bracket托架BumperBlock缓冲块Buster堵口CastingLadle浇注包CastingLug铸耳Cavity模腔模穴（模仁）CavityRetainerPlate模穴托板CenterPin中心梢ClampingBlock锁定块CoilSpring螺旋弹簧ColdPunchedNut冷冲螺母CoolingSpiral螺旋冷却栓。
模具英语
替换镶件：Interchangeable Mold Inserts。
模芯：Parting Core。
侧抽芯：Side Action 。
脱螺纹：unscrew。
excluding metallic parts price：不包括五金件价格。
Subtract to button up, convenient mold：反向弹出：reverse eject，硬度：hardness 。
牛角进胶：cashew gate 。
runner system：浇道系统。
stress crack：应力电裂。
orientation：定向。
sprue gate；射料浇口。
直浇口：nozzle射嘴。
slag well：冷料井。
bronze：青铜。
brass；黄铜。
prototype mold；手办模。
side gate：侧浇口。
edge gate：侧缘浇口。
tab gate：搭接浇口。
film gate：薄膜浇口。
flash gate：闸门浇口。
slit gate：缝隙浇口。
fan gate：扇形浇口。
dish gate：因盘形浇口。
Mold working automatic 模具自动生产 overmolding 包胶模H=F=1/2t~1/5t 。
T=2.5~3.5mm 。
diaphragm gate：隔膜浇口。
ring gate：环形浇口。
Sub gate：潜入式浇口。
tunnel gate：隧道式浇口 pin gate：针点浇口。
晒纹Texturing。
方铁;Spacer Block . 顶针板:Ejector Plate。
There are under cut at this area of part 零件这处有倒扣，can not be released 不能脱模 runner shut off 转水口cavity and core direct cut on A.B-plate 料位在A,B板上原身出。
2 stage ejection 二次顶出interchangeable cavity,core and sliders for each part互换前后模和行位生产每一个产品。
模具术语中英文对照
模具术语中英文对照模具(Mold) - A shaped cavity or matrix into which molten or uncured material is poured so thatupon solidification it will take on the shape of the cavity.注射模(Injection mold) - A molding cavity created by injecting material into a mold via a runner system.常用于塑料件注塑。
压铸模(Die casting mold) - A metal mold created for die casting processes, usually zinc, copper or aluminum based alloys.充型范(Pattern) - A full sized model of the desired casting, used to create the mold cavity in processes like sand casting.冒口(Sprue) - The primary vertical channel through which liquid material is poured into mold cavities.冒口通过主要供料道向模板腔内引入熔融金属。
气孔(Vent) - A small channel allowing the gases formed (by vaporization,chemical reaction etc.) to escape from mold cavity.用来排出模具腔内气体的小通道。
流道(Gate) - The channel that conveys molten metal from the sprue into the mold cavity.将熔融金属从主流道(冒口)引入模腔的小槽道。
模具专业英文术语大全
模具专业英文术语大全1. Die - 模具2. Mold - 模具3. Cavity - 型腔4. Core - 芯子5. Ejector pin - 顶杆6. Land - 分型面7. Gate - 浇口8. Filleting - 去毛刺9. Trim - 修整10. Draft - 拔模斜度11. Undercut - 底切12. Flash - 飞边13. Warpage - 翘曲14. Shrinkage - 收缩15. Melt flow rate - 熔融指数16. Injection molding - 注塑成型17. Blow molding - 吹塑成型18. Compression molding - 压缩成型19. Vacuum molding - 真空成型20. Overmolding - 包覆成型21. Co-injection molding - 双色注塑成型22. Gas assist injection molding - 气体辅助注塑成型23. Rotational molding - 旋转成型24. Injection compression molding - 注射压缩成型25. Injection blow molding - 注射吹塑成型26. Injection stretch blow molding - 注射拉伸吹塑成型27. Injection transfer molding - 注射传递成型28. Injection foam molding - 注射发泡成型29. Injection gas assisted rotational molding - 注射气体辅助旋转成型30. Injection compression blow molding - 注射压缩吹塑成型31. Injection stretch blow molding - 注射拉伸吹塑成型32. Injection transfer blow molding - 注射传递吹塑成型33. Injection foam blow molding - 注射发泡吹塑成型34. Injection gas assisted transfer molding - 注射气体辅助传递成型35. Injection compression foam molding - 注射压缩发泡成型36. Injection stretch foam molding - 注射拉伸发泡成型37. Injection transfer foam molding - 注射传递发泡成型38. Injection gas assisted foam blow molding - 注射气体辅助发泡吹塑成型39. Injection compression foam blow molding - 注射压缩发泡吹塑成型40. Injection stretch foam blow molding - 注射拉伸发泡吹塑成型41. Injection transfer foam blow molding - 注射传递发泡吹塑成型42. Injection gas assisted compression molding - 注射气体辅助压缩成型43. Injection gas assisted stretch blow molding - 注射气体辅助拉伸吹塑成型44. Injection gas assisted transfer blow molding - 注射气体辅助传递吹塑成型45. Injection gas assisted foam compression molding - 注射气体辅助发泡压缩成型46. Injection gas assisted foam stretch blow molding - 注射气体辅助发泡拉伸吹塑成型47. Injection gas assisted foam transfer blow molding - 注射气体辅助发泡传递吹塑成型48. Injection gas assisted compression foam molding - 注射气体辅助压缩发泡成型49. Injection gas assisted stretch foam blow molding - 注射气体辅助拉伸发泡吹塑成型50. Injection gas assisted transfer foam blow molding - 注射气体辅助传递发泡吹塑成型51. Mold temperature control system - 模具温度控制系统52. Coolant system - 冷却系统53. Ejector system - 顶出系统54. Feed system - 喂料系统55. Packaging machine - 包装机56. Automated guided vehicle (AGV) - 自动导引车（AGV）57. Robotic arm - 机械臂58. Computer numerical control (CNC) machine - 计算机数控（CNC）机床59. Plastics injection machine - 塑料注塑机60. Plastics extruder - 塑料挤出机61. Plastics blow molding machine - 塑料吹塑机62. Plastics injection compression molding machine -塑料注塑压缩成型机63. Plastics injection stretch blow molding machine - 塑料注塑拉伸吹塑成型机64. Plastics injection transfer molding machine - 塑料注塑传递成型机65. Plastics injection foam molding machine - 塑料注塑发泡成型机66. Plastics injection gas assisted rotational molding machine - 塑料注塑气体辅助旋转成型机67. Plastics injection compression foam molding machine - 塑料注塑压缩发泡成型机68. Plastics injection stretch foam molding machine - 塑料注塑拉伸发泡成型机69. Plastics injection transfer foam molding machine - 塑料注塑传递发泡成型机70. Plastics injection gas assisted foam blow molding machine - 塑料注塑气体辅助发泡吹塑成型机71. Plastics injection compression foam blow molding machine - 塑料注塑压缩发泡吹塑成型机72. Plastics injection stretch foam blow molding machine - 塑料注塑拉伸发泡吹塑成型机73. Plastics injection transfer foam blow moldingmachine - 塑料注塑传递发泡吹塑成型机74. Plastics injection molding machine with movable platen - 带活动模板的塑料注塑机75. Plastics injection molding machine with fixed platen - 带固定模板的塑料注塑机76. Plastics injection molding machine with hot runner system - 带热流道系统的塑料注塑机77. Plastics injection molding machine with cold runner system - 带冷流道系统的塑料注塑机78. Plastics injection molding machine with multi-cavity design - 带多腔设计的塑料注塑机79. Plastics injection molding machine with clamping force control - 带夹紧力控制的塑料注塑机80. Plastics injection molding machine with cycle time reduction - 带循环时间缩短的塑料注塑机81. Plastics injection molding machine with energy saving features - 带节能功能的塑料注塑机82. Plastics injection molding machine with high precision control - 带高精度控制的塑料注塑机83. Plastics injection molding machine with automatic tool changing system - 带自动换模系统的塑料注塑机84. Plastics injection molding machine with roboticautomation - 带机器人自动化的塑料注塑机85. Plastics injection molding machine with quality control system - 带质量管理系统的塑料注塑机86. Plastics injection molding machine with process monitoring system - 带工艺监控系统的塑料注塑机87. Plastics injection molding machine with maintenance reminder system - 带维护提醒系统的塑料注塑机88. Plastics injection molding machine with data logging and analysis - 带数据记录和分析的塑料注塑机89. Plastics injection molding machine with remote control and monitoring - 带远程控制和监控的塑料注塑机90. Plastics injection molding machine with safety features - 带安全功能的塑料注塑机91. Plastics injection molding machine with operator interface - 带操作员界面的塑料注塑机92. Plastics injection molding machine with easy cleaning system - 带易清洁系统的塑料注塑机93. Plastics injection molding machine with quick change tooling - 带快速换模装置的塑料注塑机94. Plastics injection molding machine with low noiseoperation - 带低噪音运行的塑料注塑机95. Plastics injection molding machine with high throughput capacity - 带高产量能力的塑料注塑机96. Plastics injection molding machine with energy recovery system - 带能量回收系统的塑料注塑机97. Plastics injection molding machine with environmental protection features - 带环保功能的塑料注塑机98. Plastics injection molding machine with advanced materials compatibility - 带先进材料兼容性的塑料注塑机99. Plastics injection molding machine with customizable options - 可定制选项的塑料注塑机100. Plastics injection molding machine with reliable performance and durability - 具有可靠性能和耐用性的塑料注塑机。
模具专业英文分类
dish gate盘形浇口
diaphragm gate隔膜浇口
ring gate环形浇口
Runner less无浇道
(sprueless)无射料管方式
long nozzle延长喷嘴方式
sprue浇口;溶渣
insulated runner/hotrunner热浇道
runner plat浇道模块
guide pad导料块
2插穿碰穿斜顶前模行位弹ke活动ke
3顶白拉伤气纹粘模走胶不齐
white mark, scratch, flow mark/ air trap ( Not sure), mold stuck, unbalance filling
4有倒扣出不了模
Have undercut, part cannot release from mold
three plates mold三板模
plaindie简易模
pierce die冲孔模
forming die成型模
progressive die连续模
gangdies复合模
shearing die剪边模
riveting die铆合模
compre sion molding压缩成型
flash mold溢流式模具
trimming punch切边冲子
stiffening rib punch =stinger加强筋冲子
ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guideplate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
模具,冲压相关英语专业翻译
模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣accurate die casting 精密压铸 powder forming 粉末成形calendaring molding 压延成形 powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形 rocking die forging 摇动锻造compound molding 复合成形 rotary forging 回转锻造compression molding 压缩成形 rotational molding 离心成形dip mold 浸渍成形 rubber molding 橡胶成形6vaggh - 2007-01-15 10:58encapsulation molding 注入成形 sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming ?泡成形 sinter forging 烧结锻造forging roll 轧锻 six sides forging 六面锻造gravity casting 重力铸造 slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸 swaging 挤锻hot forging 热锻 transfer molding 转送成形injection molding 射出成形 warm forging 温锻investment casting 精密铸造 matched die method 对模成形法laminating method 被覆淋膜成形 low pressure casting 低压铸造lost wax casting 脱蜡铸造 matched mould thermal forming 对模热成形模7vaggh - 2007-01-15 10:58各式模具分类用语bismuth mold 铋铸模 landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具 loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具counter punch 反凸模 modular mold 组合式模具8vaggh - 2007-01-15 10:58double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模 palletizing die 叠层模family mold 反套制品模具 plaster mold 石膏模blank through dies 漏件式落料模 porous mold 通气性模具duplicated cavity plate 复板模 positive mold 全压式模具fantail die 扇尾形模具 pressure die 压紧模fishtail die 鱼尾形模具 profile die 轮廓模flash mold 溢料式模具 progressive die 顺序模gypsum mold 石膏铸模 protable mold 手提式模具hot-runner mold 热流道模具 prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具 sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具9vaggh - 2007-01-15 10:59segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套 single cavity mold 单腔模具solid forging die 整体锻模 split forging die 拼合锻模split mold 双并式模具 sprueless mold 无注道残料模具squeezing die 挤压模 stretch form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具 trimming die 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模10vaggh - 2007-01-15 10:59模具厂常用之标准零配件air vent vale 通气阀 anchor pin 锚梢angular pin 角梢 baffle 调节阻板angular pin 倾斜梢 baffle plate 折流档板ball button 球塞套 ball plunger 定位球塞ball slider 球塞滑块 binder plate 压板blank holder 防皱压板 blanking die 落料冲头bolster 上下模板 bottom board 浇注底板bolster 垫板 bottom plate 下固定板bracket 托架 bumper block 缓冲块buster 堵口 casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁)cavity retainer plate 模穴托板 center pin 中心梢clamping block 锁定块 coil spring 螺旋弹簧cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓core 心型 core pin 心型梢cotter 开口梢 cross 十字接头cushion pin 缓冲梢 diaphragm gate 盘形浇口11vaggh - 2007-01-15 10:59die approach 模头料道 die bed 型底die block 块形模体 die body 铸模座die bush 合模衬套 die button 冲模母模die clamper 夹模器 die fastener 模具固定用零件die holder 母模固定板 die lip 模唇die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck 爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆 drive bearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin 顶出梢ejector plate 顶出板 ejector rod 顶出杆ejector sleeve 顶出衬套 ejector valve 顶出阀eye bolt 环首螺栓 filling core 椿入蕊film gate 薄膜形浇口 finger pin 指形梢finish machined plate 角形模板 finish machined round plate 圆形模板12vaggh - 2007-01-15 10:59fixed bolster plate 固定侧模板 flanged pin 带凸缘?flash gate 毛边形浇口 flask 上箱floating punch 浮动冲头 gate 浇口gate land 浇口面 gib 凹形拉紧?goose neck 鹅颈管 guide bushing 引导衬套guide pin 导梢 guide post 引导柱guide plate 导板 guide rail 导轨head punch 顶?冲头 headless punch 直柄冲头heavily tapered solid 整体模蕊盒 hose nippler 管接头impact damper 缓冲器 injection ram 压射柱塞inlay busher 嵌入衬套 inner plunger 内柱塞inner punch 内冲头 insert 嵌件insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockout bar 脱模杵land 合模平坦面 land area 合模面leader busher 导梢衬套 lifting pin 起模顶?lining 内衬 locating center punch 定位中心冲头locating pilot pin 定位导梢 locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush 活动衬套making die 打印冲子 manifold block 歧管档块master plate 靠模样板 match plate 分型板mold base 塑胶模座 mold clamp 铸模紧固夹mold platen 模用板 moving bols13vaggh - 2007-01-15 11:00parallel block 平行垫块 paring line 分模线parting lock set 合模定位器 pass guide 穴型导板peened head punch 镶入式冲头 pilot pin 导?pin gate 针尖浇口 plate 衬板pre extrusion punch 顶挤冲头 punch 冲头puncher 推杆 pusher pin 衬套梢rack 机架 rapping rod 起模杆re-entrant mold 凹入模 retainer pin 嵌件梢retainer plate 托料板 return pin 回位梢riding stripper 浮动脱模器 ring gate 环型浇口roller 滚筒 runner 流道runner ejector set 流道顶出器 runner lock pin 流道拉梢screw plug 头塞 set screw 固定螺丝shedder 脱模装置 shim 分隔片shoe 模座之上下模板 shoot 流道shoulder bolt 肩部螺丝 skeleton 骨架slag riser 冒渣口 slide(slide core) 滑块slip joint 滑配接头 spacer block 间隔块spacer ring 间隔环 spider 模蕊支架spindle 主轴 sprue 注道sprue bushing 注道衬套 sprue bushing guide 注道导套sprue lock bushing 注道定位衬套 sprue puller 注道拉料? 14vaggh - 2007-01-15 11:00spue line 合模线 square key 方键square nut 方螺帽 square thread 方螺纹stop collar 限位套 stop pin 止动梢stop ring 止动环 stopper 定位停止梢straight pin 圆柱? stripper bolt 脱料螺栓stripper bushing 脱模衬套 stripper plate 剥料板stroke end block 行程止梢 submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱 support pin 支撑梢supporting plate 托板 sweep templete 造模刮板tab gate 辅助浇口 taper key 推拔键taper pin 拔锥梢/锥形梢 teeming 浇注three start screw 三条螺纹 thrust pin 推力销tie bar 拉杵 tunnel gate 隧道形浇口vent 通气孔 wortle plate 拉丝模板。
3-塑胶模具专业英文单词
模具固定用零件 母模固定板 模唇 冲模板 冲压模座 直接浇口 爪牙夹头 定位梢 导套孔 合模梢 固定侧模板 带凸缘针 毛边形浇口 上箱 浮动冲头 浇口 浇口面 凹形拉紧楔 鹅颈管 引导衬套 导梢 引导柱 导板 导轨 冲头 直柄冲头 整体模蕊盒 管接头 缓冲器 压射柱塞 嵌入衬套 内柱塞 内冲头 嵌件 嵌件梢 转向梢 塑胶模座 铸模紧固夹 模用板 换模保持装置 可动侧模板 整体铸件 平行垫块 分模线 合模定位器 穴型导板
模具中英文對照表
英 文 模具零件類 Mold Components 三板模 二板模 边钉 导边 边司 导套 中托司 中托边 顶针板 托板 螺丝 管钉 开模槽 内模管位 顶针 司筒 司筒针 推板 Movable Core Return Core Puller 缩呵 Nylon Latch Lock 扣机（尼龙拉勾） Lifter 斜顶 Mold Base 模胚（架） Cavity Insert 上内模 Core Insert 下内模 Slide 行位（滑块） Insert 镶件 Wedge 压座 Wedge Wear Plate 耐磨板 油板 Plate 压条 Support Pillar 撑头 Top Plate 上托板（顶板） Top Block 上垫脚 Punch Set 上模座 Punch Pad 上垫板 Punch Holder 上夹板 Stripper Pad 脱料背板 Up Stripper 上脱料板 Male Die 公模（凸模） Feature Die 公母模 Female Die 母模（凹模） Upper Plate 上模板 Lower Plate 下模板 Die Pad 下垫板 Die Holder 下夹板 Die Set 下模座 Bottom Block 下垫脚 Bottom Plate 下托板（底板） 3-Plate Mold 2-Plate Mold Leader Pin Guide Pin Bushing Guide Bushing Shoulder Guide Bushing Guide Pin Ejector Retainner Plate Support Plate Screw Dowel Pin Ply Bar Scot Core Cavity inter-Lock Ejector Pin Ejector Sleeve Ejector Pin Stripper Plate 挡板 定位圈 锁扣 扣鸡 推杆 栓打螺丝 顶板 活动臂 分流锥 分流板 水口司 垃圾钉 隔片 弹弓柱 弹弓 中托司 中托边 镶针 销子 波子弹弓 喉塞 锁模块 斜顶 斜顶杆 尼龙拉勾 活动臂 复位键 提前回杆 气阀 压线冲子 字模冲子 圆冲子 异形冲子 折刀 滚轴 挡块 定位块 Supporting Block for Location 定位支承块 Air Cushion Plate 气垫板 Air-Cushion Eject-rod 气垫顶杆 Trimming Punch 切边冲子 Stiffening Rib Punch Stinger 加强筋冲子 Ribbon Punch 压筋冲子 Reel-stretch Punch 卷圆压平冲子 Guide Plate 定位板 Sliding Block 滑块 Stop Plate Locating Ring Latch Parting Lock Set Push Bar S.H.S.B Ejector Plate Lever Arm Sprue Spreader Spreader Plate Bush Stop Pin Buffle Spring Rod Die Spring Ejector Guide Bush Ejector Guide Pin Pin Dowel Pin Ball catch Pipe Plug Lock Plate Angle from Pin Angle Ejector Rod Parting Locks Lever Arm Early Return Bar Valves Groove Punch Stamped Punch Round Punch Special Shape Punch Bending Block Roller Baffle Plate Located Block 中 文 英 文 中 文
模具专业英文术语大全
模具英语专业术语一、图纸制图用术语英语基准： datum公差: tolerance尺寸：dimension圆角： fillet半径：radius曲线： curve公称直径：nominal diameter正方形：square直线度：straightness平面度：flatness圆度：roundness圆柱度：cylindricity线轮廓度：profile of line面轮廓度：profile of surface平行度：parallelism位置公差：position tolerance垂直度：perpendicularity周围标志：all around symbol倾斜度：angularity同轴度：coaxlality同心度：concentricity对称度: symmetry位置度：position圆跳动:run out全跳动: total run out最大材料状态：maximum material condition (MMC)最小材料状态: least material condition (LMC)不论大小的特征：no symbol regardless of feature size (RFS)投影公差区：projected tolerance zone切平面: tangent plane自由状态的变化：free state variations基本尺寸：basic dimension参考尺寸：reference dimension基准特征：datum feature尺寸源：dimension origin特征控制框：feature control frame圆锥锥度： conical taper斜坡度：slope沉孔或忽孔： counter bore/ spot face埋头孔：countersink深度：depth相同的地方：number of places电弧长度：arc length厚度：thickness球面半径：SR spherical radius均布：EQS球面直径公差值：SØ spherical diameter 控制半径：CR controlled radius45度倒角: 45 chamfer之间-表明：between统计公差：statistical tolerance基准目标：datum target靶点： target point公称厚度：nominal thickness图纸中常用术语：交界面：interface冲压工艺试验：stamping process pilot 防错工艺：POKA YOKE process翻领：collar单向的：unidirectional理论重量：theoretical weight分段区：segment定位孔：pilot hole缺陷：defect氧化：oxidation毛刺：burr税利边缘：sharp edges刀痕：tool marks闪点：flashing褶皱：wrinkles开裂：crack/splitting撕裂：tear老化：aging间隙：gap压伤：crush刮伤：scratch擦伤：scratch拉伤：abrasion划伤：scoring变形：deformation缺料：short shot挤料：extrusion deformation打磨严重：serious grinding尺寸不良：out-of-size锈斑：rust麻点：pit油脂：grease/lubricants/oil模具：tooling / die/ mold/ mould检具：checking fixture/ gauge工装：fixture三坐标测量： coordinate measuring machine简易模：plain die连续模：progressive die传递模：transfer die复合模：gang die型腔母模：mould cavity模芯公模：mould core上模板：下模板：上垫板：下垫板：冲压：stamping冲孔：pierce落料/下料：blank成型：form整型：restrike切边：trim折弯：bend翻边：flange翻孔：extrude卷耳：curling导向：pilot压筋：bead压凸台：emboss空步：idle回折：tip back拉深：draw剪边：shear铆合：rivet印字：stamp marker压印：coin压平： stretch切断：cut off切开：split切舌：lance斜楔：cam模具述语一、入水：gate进入位： gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口： switching runner/gate唧嘴口径： sprue diameter二、流道: runner热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴： hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples 插头： connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connectorplug/socker四、模具零件： mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing 中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板： support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针： ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cuton B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length 稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half定模座板 fixed clamp plate, top clamping plate. top plate动模座板 moving clamp plate. bottom clamping plate. bottom plate上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate垫块 spacer parallel支架 ejector housing. mould base leg 压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材 khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector 阴连接器Housing阳连接器wafer 线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance绝缘电阻insulation resistance超声波焊接ultrasonic welding耐压withstand voltage针pin物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity接触长度contact length接触件电镀层contact plating接触压力contact pressure接触件中心距contact space接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ，Ribbon cable柔性印刷电线Flexible printed wiring多层印制电路Multilayer printed circuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board，Double-sided board表面安装surface Mounting翘曲warp， bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould 冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half 上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould 熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板（顶板）Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块（嵌入件）Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具标准翻译。
模具常用名称中英文对应表
電阻焊接 固定圈 螺絲批 點焊 彈簧夾 彈簧墊圈 雙頭螺栓 轉矩扳鉗 觸針 超聲焊接
resistance welding retaining ring screw driver spot welding spring clips spring washer stud torque wrench welding horn ultrasonic welding
模具常用名稱中英文對應表 中文名 模胚 模（前模） 口哥（后模） 細水口 大水口 水口板 水口推板 模板 口哥板 面針板 底針板 方鐵（凳仔方） 底板 水口邊（支撐針） 直邊（導柱）/導向針 水口拉 木旱 托司(導套) 直司 回針 唧嘴 熱呶嘴 入水 流道 定位圈（法蘭） 水口鉤針 塞打螺絲 彈弓膠 拉膠 頂針 扁頂針 有托頂針 司筒針 單頭柳釘 平接 電動螺絲批 氣動螺絲批 換能器 焊條 磨擦焊接 氣焊 膠 熱壓封口 搭接 保險螺絲 螺母 英文名 簡稱 Mold Base Cavity Core Pin Point Gate Side gate Top clamp Plate Stripper Plate A Plate B Plate Ejector Retainer Plate Ejector Plate Spacer Block Bottom Clamp Plate Support Pin S.P. Guide Pin G.P. Small Support Pin S.S.P. Shoulder Guide Bush SH.G.B. Straight Guide Bush S.G.B. Return Pin R.P. Sprue Bushing SP.B. Hot Sprue Bushing Gate Runner Locating Ring L.R. Runner Lock Pin R.L.P. Puller Bolt C TYPE P.B.C. Rubber Spring R.S. Parting Lock PA.L. Ejector Pin E.J.P. Ejector Blade E.J.B. Stepped Ejector Pin S.E.J.P. Ejector Sleeves E.J.S. blind rivet butt joint screw driver, electric screw driver,pneumatic energy converter filler rod friction welding gas welding glue heat sealing lap joint lock nut/lock washer nut 中文名 推方 英文名 簡稱 Ejector Block E.J.K. Insert 行位 Slide 斜方 Slant 鑲針 Insert Pin I.P. 拈板 Clamp Wedge 開模線面 Parting Line P.L. 杯頭螺絲 Screws 硬板 Harden Plate 電鑄 Electro-formed 中托邊 Ejector Guide Bushigs E.G.P. 撐頭 Support Block S.B. 彈弓 Spring 運水 Cooling 運水膠圈 "0"Ring 運水桶 Cooling Hole 喉嘴 Water Junction W.J. 發熱管 Hot Pin 拉令孔 Tapped Hole For Eyebolt 蝴蝶鉸 Butterfly Ware 拉勾(扣基) Multi Lock 指示針 Date Code 字嘜 Indicator 彈弓螺絲 Spring Screw 拉圾釘 Stop Pin 方型輔助器 Straight Side Interlocks S.S.L. 斜邊釘 Taper InterLock T.L. 斜導柱 Angular Pin A.P. 定位扣 "P" Lock P.K. 銷釘 Dowel Pin D.P. 斜鎖位 taper Block Set-ky TYPE T.B.S. 中文名 添加劑 粘結劑 醇酸(樹脂) 抗氧化劑 抗靜電劑 觸媒,催化劑 涂層 著色劑 化合物 硬化劑 填充劑 阻烯劑 起泡劑 層壓料 潤滑劑 單聚物 增強劑 樹脂 溶劑 穩定劑(器) 紫外線吸收劑 超聲波模 螺紋 螺旋形的 倒扣,咬邊 操作表面 鋼公 加工程序 英文名 (')additive adhesive alkyd antioxidant antigtatic agent catalyst coating colorant compound daring agent(hardener) filler flame retardant foaming agent laminated lubricant monomer reinforcing agent resin solvent stabilizer ultraviolet absorber ultrasonic welding thread spiral undercut actuating surface electrode secondary process 中文名 燃燒率 冷流 壓縮強度 開裂應力 蠕變 撓曲溫度 介電常數 介電強度 體積穩定性 彈性模數 伸長 防火 可燃性 彎曲強度 耐熱 沖擊強度 模塑收縮量 戶外風蝕 抗刮磨 抗剪/切變強度 軟化溫度 比重 腫脹 抗撕裂/抗扯強度 抗拉強度 熱傳導性 熱膨脹系數 粘度 翹曲 附針(導柱) 司(導套,套司) 平行板 壓板 墊片 碼板 托板(固定器) 勾針 頂針 頂針板 托板 頂針 頂出條 頂出板 壓條,碼板 英文名 burning rate cold flow 3 compressive strength cracking stress creep deflection temperature dielectric constant dielectric strength dimensional stability elastic moulds elongation flame resistance flammability flexural strength heat resistance impact stregnth mould shrinkage scoutdoor weathering scratch resistance shear strength softening point specific gravity swelling tear resistance tensile strength thermal conductivity thermal expanion coefficient viscosity warpage guide pins guide pin bushings parallels clamping plate pressure pads mounting plates retainers pot plungers pots pot retainers backing plates knockout pins knockout bars knockout pin plates gibs
模具术语中英文表
流道拉料銷（SPRUCE PULLER）
60 肩部螺絲（SHOUL SCREW） 90
模具專業朮語
1 毛邊（BURR） 2 段差（STEP） 3 缺料/短射（SHORT SHOT） 4 頂白（EJECT MARKS） 5 結合線（WELDING LINE） 6 流痕（FLOW MARKS） 7 尺寸太大（COER SIZE） 8 尺寸太小（UNDER SIZE） 9 位置錯位（ERROR） 10 拉傷（SCRATCH ） 11 變形（DEFORMATION） 12 縮水/凹痕（SINK MARK） 13 凸出（RAISE） 14 塑膠（PLASTIC ） 15 翹曲（WARP/BENDING） 16 氣泡（AIR BLADDER） 17 尺寸（SIZE） 18 分模線（PARTING LINE） 19 細裂痕（CHECK） 20 畫痕（SCRATCH) 21 咬入（BITE） 22 切邊碎片（EDGE） 23 矯直（STRAIGHTENING） 24 波動（SURGING） 25 廢料（SCRAP） 26 廢料阻塞（SCRAP） 27 坑（PIT） 28 破孔（BLOW HOLE） 29 麻點（POCK） 30 色差（ABERRATION）
78 雙節頂針（SHOULDER EJECTOR PIN）
79
斜度定位柱（TAPER SETS）
PIN
80 斜度定位塊（TAPER BLOCK SETS）
81 定位拉板（TENSION LINKS)
22 靠破（SHUT-OFF）
52 壓板（BINDER PLATE）
82 防水圈（"O"RING）
23 水孔（WATER LINE）
20 鋸削（SAWING）
22 表面研磨（SKIVING）
模具中英文对照
模具中英文对照accurate die casting 精密压铸 powder forming 粉末成形calendaring molding 压延成形 powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形 rocking die forging 摇动锻造compound molding 复合成形 rotary forging 回转锻造compression molding 压缩成形 rotational molding 离心成形dip mold 浸渍成形 rubber molding 橡胶成形encapsulation molding 注入成形 sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming 发泡成形 sinter forging 烧结锻造forging roll 轧锻 six sides forging 六面锻造gravity casting 重力铸造 slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸 swaging 挤锻hot forging 热锻 transfer molding 转送成形injection molding 射出成形 warm forging 温锻investment casting 精密铸造 matched die method 对模成形法laminating method 被覆淋膜成形 low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模 landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具 loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具counter punch 反凸模 modular mold 组合式模具double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模 palletizing die 叠层模family mold 反套制品模具 plaster mold 石膏模blank through dies 漏件式落料模 porous mold 通气性模具duplicated cavity plate 复板模 positive mold 全压式模具fantail die 扇尾形模具 pressure die 压紧模fishtail die 鱼尾形模具 profile die 轮廓模flash mold 溢料式模具 progressive die 顺序模gypsum mold 石膏铸模 protable mold 手提式模具hot-runner mold 热流道模具 prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具 sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套 single cavity mold 单腔模具solid forging die 整体锻模 split forging die 拼合锻模split mold 双并式模具 sprueless mold 无注道残料模具squeezing die 挤压模 stretch form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具 trimming die 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀 anchor pin 锚梢angular pin 角梢 baffle 调节阻板angular pin 倾斜梢 baffle plate 折流檔板ball button 球塞套 ball plunger 定位球塞ball slider 球塞滑块 binder plate 压板blank holder 防皱压板 blanking die 落料冲头bolster 上下模板 bottom board 浇注底板bolster 垫板 bottom plate 下固定板bracket 扥架 bumper block 缓冲块buster 堵口 casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁) cavity retainer plate 模穴扥板 center pin 中心梢clamping block 锁定块 coil spring 螺旋弹簧cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓core 心型 core pin 心型梢cotter 开口梢 cross 十字接头cushion pin 缓冲梢 diaphragm gate 盘形浇口die approach 模头料道 die bed 型底die block 块形模体 die body 铸模座die bush 合模衬套 die button 冲模母模die clamper 夹模器 die fastener 模具固定用零件die holder 母模固定板 die lip 模唇die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck 爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆 drive bearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin 顶出梢ejector plate 顶出板 ejector rod 顶出杆ejector sleeve 顶出衬套 ejector valve 顶出阀eye bolt 环首螺栓 filling core 椿入蕊film gate 薄膜形浇口 finger pin 指形梢finish machined plate 角形模板 finish machined round plate 圆形模板fixed bolster plate 固定侧模板 flanged pin 带凸缘销flash gate 毛边形浇口 flask 上箱floating punch 浮动冲头 gate 浇口gate land 浇口面 gib 凹形拉紧销goose neck 鹅颈管 guide bushing 引导衬套guide pin 导梢 guide post 引导柱guide plate 导板 guide rail 导轨head punch 顶镦冲头 headless punch 直柄冲头heavily tapered solid 整体模蕊盒 hose nippler 管接头impact damper 缓冲器 injection ram 压射柱塞inlay busher 嵌入衬套 inner plunger 内柱塞inner punch 内冲头 insert 嵌件insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockout bar 脱模杵land 合模平坦面 land area 合模面leader busher 导梢衬套 lifting pin 起模顶销lining 内衬 locating center punch 定位中心冲头locating pilot pin 定位导梢 locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush 活动衬套making die 打印冲子 manifold block 歧管档块master plate 靠模样板 match plate 分型板mold base 塑料模座 mold clamp 铸模紧固夹mold platen 模用板 moving bolster 换模保持装置moving bolster plate 可动侧模板 one piece casting 整体铸件parallel block 平行垫块 paring line 分模线parting lock set 合模定位器 pass guide 穴型导板peened head punch 镶入式冲头 pilot pin 导销pin gate 针尖浇口 plate 衬板pre extrusion punch 顶挤冲头 punch 冲头puncher 推杆 pusher pin 衬套梢rack 机架 rapping rod 起模杆re-entrant mold 凹入模 retainer pin 嵌件梢retainer plate 扥料板 return pin 回位梢riding stripper 浮动脱模器 ring gate 环型浇口roller 滚筒 runner 流道runner ejector set 流道顶出器 runner lock pin 流道拉梢screw plug 头塞 set screw 固定螺丝shedder 脱模装置 shim 分隔片shoe 模座之上下模板 shoot 流道shoulder bolt 肩部螺丝 skeleton 骨架slag riser 冒渣口 slide(slide core) 滑块slip joint 滑配接头 spacer block 间隔块spacer ring 间隔环 spider 模蕊支架spindle 主轴 sprue 注道sprue bushing 注道衬套 sprue bushing guide 注道导套sprue lock bushing 注道定位衬套 sprue puller 注道拉料销spue line 合模线 square key 方键square nut 方螺帽 square thread 方螺纹stop collar 限位套 stop pin 止动梢stop ring 止动环 stopper 定位停止梢straight pin 圆柱销 stripper bolt 脱料螺栓stripper bushing 脱模衬套 stripper plate 剥料板stroke end block 行程止梢 submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱 support pin 支撑梢supporting plate 扥板 sweep templete 造模刮板tab gate 辅助浇口 taper key 推拔键taper pin 拔锥梢/锥形梢 teeming 浇注three start screw 三条螺纹 thrust pin 推力销tie bar 拉杵 tunnel gate 隧道形浇口vent 通气孔 wortle plate 拉丝模板。
模具英文- for poster
1.Drawing/2D drawing--2D图纸2.3D--三维模型3.Upper plate--上模4.Bottom plate--下模5.Middle plate--中板6.Paper pattern--纸版7.Top net pattern--内仁版8.Upper pattern--上版9.Bottom pattern--大底板10.Wedge angle--后跟面角度11.Medial wall gauge--内墙板st bottom gauge--楦底板13.Bottom gauge--底花板14.Top gauge--模口板15.Section--剖切板16.Section A-A/profile--龙骨板17.Top net gauge--下内仁板18.Top out gauge--内围板19.Midsole sidewall--中底边墙20.Outsole sidewall--大底边墙21.Medial/lateral side view--内/外侧视图22.Parting line--分模线23.Mark point--记号点24.Sample size--样品号码25.Full size--全套号码26.Grading--级放27.Grouping—分段28.Mass production--量产29.Original/first mold--初模30.Revise/modify/change/adjust/update--修改31.Confirm--确认32.Rubber outsole--橡胶大底33.Hand rubber--加硫底34.De-molding--脱模35.Distortion--变形36.Outsole mould--大底模具37.Midsole mould--中底38.Injection midsole--射出中底pression midsole--热压中底40.EVA cold molding--冷压EVA41.Poured PU--灌注PU42.Sponge EVA--发泡EVA43.Molded EVA wedge--成型的EVA中插44.Cup sole--全包底45.Cup wall--包边墙46.EDM/electrical discharge machine--放电47.Electric welding--电焊48.Electroplating--电镀49.Engraving--雕刻ser cut—镭射51.Planing machine--刨床C(computer number control)-CNC机器53.Sole maker--底厂54.CAD(computer-aided-design)--电脑辅助设计55.Cast mold--铸模56.Cutting die gauge-裁刀板57.Pression pad—压底垫58.Color dam--隔色沟59.Color bleeding –-溢色60.Color-way--配色61.Heel center line--后跟中心线st center line--头中心线63.Heel covering--包鞋跟64.Heel cup--鞋跟杯65.Instep girth--脚背周长66.Instep point--脚背点67.Instep high--脚背高度68.Waist girth--腰围69.Lug/studs--颗粒70.Herring bone--水波纹71.Honey comb--省料槽72.Radius/fillet--R度/R角73.Angle--角度74.Chamfer—斜度75.Flex groove--弯曲沟76.Stitching groove--车线沟77.Flash--毛边/水口78.Texture--咬花79.Buffing--打粗80.Polish--抛光81.Sandblast--喷砂82.Printing--喷漆/印刷83.Symmetry--对称84.Parallel--平行85.Rotate--旋转86.Undercut--倒插87.Forefoot--前掌88.Footbed--脚床面89.Midfoot—中腰90.Ground contact--着地面91.Shank--中腰弧形92.Pattern grading--纸板级放st bottom feather line--帮脚线st bottom width--楦底(掌面)宽度teral/medial gauge--外/内墙板yer--层97.Leg of the boot--靴统98.Throat of vamp--鞋口开度，鞋喉99.Toe spring--鞋头翘度100.H eel spring—后跟翘度。
模具中英文通用名_
模具中英文通用名称.doc以下是模架：模胚—Mold Base顶板—Top Clamp Plate脱料板—Runner Stripper Plate热流板—Spacer Plate母模板—A Plate推板—Stripper Plate公模板—B Plate承板—Support Plate方铁—Spacer Block面针板—Ejector Retainer Plate底针板—Ejector plate底板—Bottom Clamp Plate以下是镶嵌件和滑块：母模仁—Cavity Insert公模仁—Core Insert滑块—Slide斜顶—Lift镶针—Core Pin镶件—Insert互换镶件—Change Insert滑块镶件—Slide Insert铲鸡—Wedge压条—Plate斜导柱—Slide Pin耐磨板—Wear Plate导向块—Guide Block斜顶导向块—Lift Guide Block 滑块导轨—Slide Guide滑块束块—Slide Wedge斜顶底座—Lift Base以下是进胶组件：唧咀—Sprue Bushing分流锥—Sprue Spreader定位环—Locating Ring胶口衬套—Sprue Bushing以下是电热组件：电热衬套—Hot Tip Bushing电热管—Heater电热圈—Heater Band线接头—Power控温耦合器—Thermocouple以下是顶针组件：顶针—Ejector Pin扁顶针—Rec. Ej. Pin方顶针—Sqrt. Ej. Pin双节顶针—Step Ej. Pin司筒—Ejector Sleeve双节司筒—Step Ej. Sleeve顶出块—Ejector Block以下是拉料组件：勾针—Sprue Pin拉杆—Puller Pillar拉料销—Runner Lock Pin开闭器—Slide Lock Set尼龙开闭器—Parting Lock以下是限位、复位、弹簧组件：复位杆—Return Pin支撑柱—Support Pillar垃圾钉—Stop Pin限制块—Stop Block开模止板—Stop Plate日期章—Date Marked Pin压力胶—Rubber Spring限位开关—Limits Switch弹簧—Spring轻小载荷弹簧—Lightest Load Spring轻载荷弹簧—Light Load Spring中载荷弹簧—Medium Load Spring重载荷弹簧—Heavy Load Spring极重载荷弹簧—Super Load Spring圆线弹簧—Wire Spring耐热弹簧—Heatproof Spring弹簧柱—Spring Rod波子弹簧—Ball Catch以下是水路组件：O型圈—O Ring隔水片—Baffle Boards喉塞—Pipe Plug水道塞子—Coolant Plug水管—Water Connection喷水管—Cascade Water Junction挡水板—Plug Baffles快速接头—Jiffy-Tile Sockets水管无头螺丝—Water Bass Pressure Plugs以下是导柱导套：导柱—Guide Pin直导套—Straight Guide Bush有托导套—Shoulder Guide Bush顶针板导柱—Ejector Guide Pin 顶针板导套—Ejector Guide Bush 以下是螺丝组件：限位螺丝—Stop Bolt无头螺丝—Screw Plug内六角螺丝—S.H.C.S平头小螺丝—F.H.C.S外六角螺丝—Hexangdlar Bolt以下是定位组件：定位销—Dowel Pin定位钢珠—Ball Plung锁模块—Lock Block0度定位块—Straight Block Set 斜度定位块—Taper Block Set圆形定位器—Taper Pin Set以下是注塑机组件：轴—Shaft轴承—Bearing齿轮—Gear凸轮—Cam Wheel气阀—Valves气压缸—Air Cylinder油压缸—Hydraulic Cylinder 油压马达—Hydraulic Motors 油封—Oil Close轴用C环—"C"Type Ring轴用E环—"E"Type Ring孔止环—Stop Hold Ring。
模具常用语中英文对照
以下是30 个模具常用语的中英文对照：1.模具：mold2.模具设计：mold design3.模具制造：mold manufacturing4.模具加工：mold processing5.模具寿命：mold life6.模具维护：mold maintenance7.模具成本：mold cost8.模具材料：mold material9.模具结构：mold structure10.模具零件：mold part11.模具装配：mold assembly12.模具调试：mold debug13.模具成型：mold forming14.模具分型面：mold parting surface15.模具型腔：mold cavity16.模具型芯：mold core17.模具滑块：mold slider18.模具斜顶：mold lifter19.模具顶针：mold ejector pin20.模具冷却系统：mold cooling system21.模具浇注系统：mold gating system22.模具排气系统：mold venting system23.模具尺寸公差：mold dimensional tolerance24.模具表面粗糙度：mold surface roughness25.模具硬度：mold hardness26.模具钢：mold steel27.模具加工工艺：mold processing technology28.模具检测：mold inspection29.模具修改：mold modification30.模具报废：mold scrap。
模具词汇
模具英文词汇对照与塑料模专业英词一、模具結構Mould / Tooling 模具Top Clamp Plate 面板Mould Base 模胚Runner Stripper Plate 水口板Gate 澆口(入水位)A Plate A 板Side Gate - 側澆口Stripper Plate 推板Pin Point Gate 點澆口B Plate--B 板Submarine Gate 潛伏澆口Support Plate 托板Disk Gate 圓盤澆口Spacer Block- 方鐵Tab Gate 薄片澆口Ejector Retainer Plate- 面針板Spoke Gate- 輪輻澆口Ejector Plate- 底針板Direct Gate直接澆口Bottom Clamp Plat底板Cavity型腔Insert 鑲件Core 型芯二、加工工具Bushing Borers 杯司鑽頭Tapered Reamers 爹把絞刀Core Pins- 哥針Ejector Pin Reamers-頂針絞刀Capscrew Counterbores--杯頭螺絲撥頭Leader Pin Reamers 導邊絞刀Ejector Pin Counterbores-頂針撥頭Springs“A”Type (Orange Color)---扁線壓力彈弓“A”(橙色)Leader Pin Counterbores--導邊撥頭Springs“B”Type (Silver Color)扁線壓力彈弓“B”(銀色) Return Pin Counterbores- 回針撥頭Tapered Drills-- 爹把鑽Shoulder Bushing Counterbores-- 有托杯司撥頭“R”Cutters-唧咀弧度刃三、螺紋標準名稱BSW 英制粗螺紋Metric (Coarse) 公制粗螺紋BSF 英制幼螺紋Metric (Fine) 公制幼螺紋BSPP 英制管平衡螺紋Pg公制電力螺紋BSPT英制管斜度螺紋UNC 美制粗螺紋BA 英國協會螺紋UNF 美制幼螺紋四、標準模具零件Angular Pins斜度邊釘Return Pins回針Dowel Pins管位釘Shoulder Bushings--有托杯司E.G. Bushing-中托司套Shoulder Leader Pins--有托導邊Ejector Pin圓身頂針Special Water Junctions--特殊喉咀Hotwork Ejector Pins耐熱頂針Spring彈簧HS Ejector Pins高速度鋼頂針Sprue Bushings唧咀Ejector Blade-扁身頂針Stop Pins限位釘Ejector Return Assembly頂針板回歸器Straight Bushings-直身杯司Ejector Sleeves-頂針司筒Straight Leader Pins-直身導邊Gas Expeller疏氣針Support Pillars 撐頭Jiggle pin- 斜頂Support Pins 細水口導邊Locating Ring 定位圈Tapered Interlocks爹把邊釘“P”Locks 定位扣Tension Link拉力板Puller Bolt Collars 拉桿介指Thermo Pin導熱針Puller Bolts脫水口螺絲Water Junctions 標准喉咀Puller Lock--拉模扣Hot Runner System熱流道系統五、不良成形現象Air Trap 困氣Flash披鋒Air Vent排氣Jetting摺紋Black Spot 黑點Short Shots 走膠不全Burning燒焦Sinks 局部收縮Burr- 毛刺Splay-Silver Streaks- 水花白Cold Well- 冷料穴Weld Line 夾水紋Distortion 扭曲六、圖紙用字Drawn By 繪圖者Chamfer- 倒角Checked By- 核對者Fillet 倒圓角Approved by- 批核者Draft Angle]\ 脫模斜度Client / Customer客戶Parting Line分型線Title 題目Center Line中心線Drawing No圖紙編號Tolerance 公差Part name零件名稱Detail View詳細圖Tool No模具編號Top View 頂視圖Tool Type模具種類Front View正視圖No of Cavity模腔數Side View側視圖Shrinkage收縮率Section View切面圖Issue發行Notes告示Modification更改Wall Thickness膠位厚度Item 項目Texture花紋Material材料Radius半徑BOM物料菜單Diameter直徑Date 日期Colour顏色Scale比例Coarse粗NTS不按比例Fine幼Unspecified未註明的Projection投影七、一般加工方法Boring鏜加工Milling銑床加工CNC數控銑床加工Polishing拋光Sand Blasting噴砂Engraving雕刻Sand Casting砂模鑄造Etching蝕紋Sawing鋸Forging鍛造Sintering燒結Grilling鑽床加工Tap攻螺絲Grinding磨床加工Turning車床加工Heat Treatment熱處理Welding燒焊Latheing車床加工Wire Cut線切割加工八、其他Injection 注射Key 鑰匙Plastic 塑膠Lens 鏡片Rubber 橡膠Handle 手柄Resin 樹脂Cover 蓋Feet 英尺Panel 表板Inch 英吋Shaft 軸Meter 米/ 公尺Motor- 馬達Millimeter 毫米Rust生鏽Height高度Dimension尺寸Depth深度Rib骨位Weight重量Glass Fiber玻璃纖維Speed速度Friction摩擦力Temperature溫度Tension拉力Screw螺絲Pressure壓力Screw Driver螺絲刀Alarm警報Thread螺紋Pneumatic氣動Pitch螺距Hydraulic液壓Base基座Cylinder唧筒Button按鈕Lubricating Oil潤滑油Gear齒輪Magnet磁石Pulley滑輪Spanner扳手Housing外殼Fixture夾具常用朮語中英文對照short shot缺膠break斷裂flash披鋒gap too large after assembly裝配間隙大dimension NG尺寸NGfailed to assembked不能裝配no conduct due to broken wire銅絲線斷,不導電力度不良defective forcedistortion變形poor plating電鍍不良damage破損returned by production line生產線退貨wire come off端子松脫printing defect tapping defect打印不良,滑絲hurt批傷Crack爆裂bruise碰傷broken snap斷扣Rust生銹Reworked by supplier供應商返工Hurt on wire線披傷Holes有針孔Scratch划傷Foreign material異物Dust灰塵Cable come off線脫落Press hurt壓傷Which caused the abnormal voice from assembly 造成裝配有異音Broken pins扞腳斷Lead wire導線Motor馬達It cannot rotate smoothly轉動不暢Loose gear齒輪松Lead wire導線Loose tube and bad insertion wire線頭熱熔膠管脫落Panel按健表板Key defect按健不良Fold皺折Structure different with sample結构與樣板不符Broken tab柱子斷Lead wire assy導線組Adaptor火牛Black specks黑點Hole blocked up塞孔Crack 破裂Mixed color料花Spec標准Actual實測Spring彈弓Non homogeneouse colour混色Hole larger孔徑大There are oil on the part surface部品表面有油Gear dent齒輪位碰傷Thickness NG厚度NGE-PIN too high頂針位高Higher gate水口位高Colour different異色Contamination 雜物Grease 油污Cosmetic defects熔膠不良Rusting 銹斑Resilience NG彈力NGSmudge 污跡Without chamfer未倒角Wire is broken線斷White plastie of terminal peal off白膠脫落Wire is broken線破損Broken snap扣位斷Loose connector線頭松脫焊線脫落The welded wire looseThe boss is shorter柱子低Oddment 碎屑Rand pick 選別游標卡尺/Vemier Caliper ( VC)電子卡尺/Digital Caliper( DC)三座標測量儀(三次元)/Coordinate Measuring Maching(CMM)電子千分尺/Digital Micrometer( DM)游標千分尺/Vernier Micrometer(VM)針規/Pin Gauge( PG)投影儀/Projector( P)電子高度尺/Digital Height Gauge( DH)游標高度尺/ Vemier Height Gauge( VH)塞尺/Thickness Gauge( TG)直尺/Ruler( R)百分表/Dial Indicator( DI)涂層厚度計/Coating Thickness Gauge( CT)塊規/Block Gauge( BG)角度規(尺)/Goniometer/Bevel Protracter( G) 直角尺/Right Angle Ruler/Spuare( AR)溫適度計表/Hygrothermograph( H)平台板/Flat/Plate( F)色差儀/Chromometer( C)鈕具表/Torfque Gauge( TE)推拉力計/Pull-Push Gauge( PP)數字鈕鉅儀/Digital Torfque Gauge( DT)電子稱/ Digital Scale( DS)法碼/Weights( WT)天平/Balance( BG)照度計/Light Meter( LM)萬用表/Multimeter(M)螺紋規/Thread Gauge( TD)表面粗糙度樣塊/Roughness Block( RB)功力表/Power Meter( PM)硬度計/Sclerometer( S)秒表/Stop Watch( SW)刀口尺/Knife Gauge( KG)放大鏡/Amlifer( A)水平儀/Level Balance ( LB)內徑千分尺/Internal Micrometer( IM)卷尺/Roll Meter( RM)耐壓測試儀器/Pressure Meter( PM)千分尺/Micrometer( M)內側千分尺/Insiele Micrometer( IM)深度千分尺/Depth Micrometer( DM)塑料模专业英语1、ejector unit顶出单元，包括一切有顶出功能的零件：ejector pin, ejector plate,ejector sleeve,ejector rod,ejector leader busher顶出导销（顶出板导杆）的衬套，也叫ejector guide bush ejector stopper,用于顶出制动的，或限位的ejector pin retaining plate:顶针固定板。
各式模具分类用语中英文对照
loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offset bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模portable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模run less injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具cassette 卡座color display 彩色显示器command 指令communication 通信compact 精简小型computer 电脑copy 复制cursor 游标curve modeling 曲面模拟database 资料库design 设计digitizing 数位化disk 磁碟dot 点eyelet 眼孔floppy 磁碟片format 格式化graphic 圆解hardware 硬体honeycomb 蜂巢interface 界面know how 秘诀laser printer 雷射印表机lay out 布置memory 记忆memory swap 交换记忆microprocessor 微处理器modeling 造型module 模组monitor 萤幕mouse 滑鼠need 需求network 网路new version 新版on line 上线中option 选择PC 个人电脑Plotter 绘图机Program 程式scanning 扫描simulation 模拟software 软体solid model 实体模型system 系统tape 磁带terminal 终端机texture 构造trim 修边word processor 文书处理器各种冲模加工关连用语barreling 滚光加工belling 压凸加工bending 弯曲加工blanking 下料加工bulging 撑压加工burring 冲缘加工cam die bending 凸轮弯曲加工coining 压印加工compressing 压缩加工compression bending 压弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工dinking 切断蕊骨double shearing 叠板裁断drawing 引伸加工drawing with ironing 抽引光滑加工embossing 浮花压制加工extrusion 挤制加工filing 锉削加工fine blanking 精密下料加工finish blanking 光制下料加工finishing 精整加工flanging 凸缘加工folding 折边弯曲加工folding 摺叠加工forming 成形加工impact extrusion 冲击挤压加工indenting 压痕加工ironing 引缩加工knurling 滚花lock seaming 固定接合louvering 百叶窗板加工marking 刻印加工necking 颈缩加工notching 冲口加工parting 分断加工piercing 冲孔加工progressive bending 连续弯曲加工progressive blanking 连续下料加工progressive drawing 连续引伸加工progressive forming 连续成形加工reaming 铰孔加工restriking 二次精冲加工riveting 铆接加工roll bending 滚筒弯曲加工roll finishing 滚压加工rolling 压延加工roughing 粗加工scrapless machining 无废料加工seaming 折弯重叠加工shaving 缺口修整加工shearing 切断加工sizing 精压加工slitting 割缝加工stamping 锻压加工swaging 挤锻压加工trimming 整缘加工upsetting 锻粗加工wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴blank determination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落锤brake 煞车buckle 剥砂面charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blanking press 精密下料冲床forging roll 辊锻机finishing slag 炼後熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching 微调尺寸isothermal forging 恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部level 水平loader 供料器unloader 卸料机loop controller 闭回路控制器lower die 下模micro inching device 微寸动装置microinching equipment 微动装置motor 马达moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device 防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距pressfit 压入progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人roll forming machine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全保护装置scrap cutter 废料切刀scrap press 废料冲床seamless forging 无缝锻造separate 分离shave 崩砂shear angle 剪角sheet loader 薄板装料机shot 单行程工作shrinkage fit 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slide balancer 滑动平衡器slug hole 逃料孔spin forming machine 旋压成形机spotting 合模stack feeder 堆叠拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程take out device 取料装置toggle press 肘杆式压力机transfer 传送transfer feed 连续自动送料装置two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机vibration feeder 振动送料机wiring press 嵌线卷边机线切割放电加工关连用语abnormal glow 不规则辉光放电arc discharge 电弧放电belt 皮带centreless 无心chrome bronze 铭铜clearance angle 後角corner shear drop 直角压陷deflection 挠曲度discharge energy 放电能量dressing 修整dwell 保压flange 凸缘gap 间隙graphite 石墨graphite contraction allowance 电极缩小余量graphite holder 电极夹座hair crack 发裂horn 电极臂jump 跳刀magnetic base 磁性座master graphite 标准电极pipe graphite 管状电极pulse 脉冲rib working 肋部加工roller electrode 滚轮式电极rotary surface 旋转面shank 柄部sharp edge 锐角部tough bronze 韧铜traverse 摇臂waviness 波形起伏work 工件working allowance 加工余量working dischard 加工废料锻铸造关连用语accretion 炉瘤acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnace 酸性平炉aerator 松砂机air set mold 常温自硬铸模airless blasting cleaning 离心喷光all core molding 集合式铸模all round die holder 通用模座assembly mark 铸造合模记号back pouring 补浇注backing sand 背砂base bullion 粗金属锭base permeability 原砂透气度belling 压凸billet 坏料bleed 漏铸blocker 预锻模膛blocking 粗胚锻件blow hole 铸件气孔board drop hammer 板落锤bottom pour mold 底浇bottom pouring 底注boxless mold 脱箱砂模break-off core 缩颈砂心brick molding 砌箱造模法buckle 剥砂面camber 错箱cast blade 铸造叶片casting flange 铸造凸缘casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗cleaning of casting 铸件清理closed-die forging 合模锻造core compound 砂心黏结剂core template 砂心模板core vent 砂蕊排气孔corner gate 压边浇口counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔die approach 模口角度draw out 锻造拔长draw plate 起模板draw spike 起模长针dummying 预锻embedded core 加装砂心erosion 冲砂fettling 铸件清理filling core 埋入砂心filling in 填砂film play 液面花纹finishing slag 炼後熔渣flash gutter 锻模飞边槽flask molding 砂箱造模forging roll 辊锻机formboard 进模口板gutter 锻模飞边槽hammer man 锻工heading machine 顶镦机impacter 卧式锻造机inblock cast 整体铸造ingot 铸锭ingot blank 铸坯inlay casting 镶铸法investment casting 失模铸造isothermal forging 恒温锻造loose piece 木模活块molding pit 铸模地坑pouring process 浇注法recasting 重铸roll forging 轧锻rolled surface 轧制表面rough sand 粗砂roughing forge 粗锻sand crushing 塌箱seamless forging 无缝锻造separate 分离shave 崩砂shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slag 熔渣slag inclusion 夹渣stickness 黏模性strip layout 带状胚料排样法tap casting 顶注top gate 顶注浇口unworked casting 不加工铸件upender 翻转装置upending 顶锻uphill casting 底铸white cast iron 白口铸件模具加工方法barrel 滚筒(加工)bending 波纹加工broaching 拉刀切削centering 定中心cutting 切削cylindrical lathe cutting 外圆车削electric discharge machine 放电加工electrolytic grinding 电解研磨embossing 压花加工facing 面车削filing 锉刀修润hand finishing 手工修润hemming 卷边加工hobbing 滚齿加工joggling 摇动加工lapping 抛光/研磨修润laser beam machining 雷射加工lathe cutting 车床车削planning 刨削加工polishing 抛亮光reaming 铰孔修润rough machining 粗切削rounding 圆形加工sawing 锯削scaling 清除钢碇缺陷shaping 成形加工skiving 表面研磨slotting 切缝切削taper turning 锥度车削thread cutting 螺纹切削ultrasonic machining 超音波加工up cut milling 逆铣加工学理实验与试验用语air permeability test 透气性试验austenitic steel 沃斯田铁钢Brinell hardness 布耐内尔硬度Brinell hardness test 布氏硬度试验Charpy impact test 夏比冲击试验conical cup test 圆锥杯突试验cup flow test 杯模式流动度试验dart drop impact test 落锤冲击试验Elmendorf test 埃罗门多撕裂强度试验environmental stress cracking test境应力龟裂试验Ericessen test 埃留伸薄板拉伸试验falling ball impact test 落球冲击试验fatigue test 疲劳试验ferrite 纯铁体Gantt chart 甘特图heat cycle test 热循环试验histogram 柱状图hot bend test 热弯试验Izod impact test 埃左德冲击试验loop tenacity 环结强度martens heat distortion temperature test 马顿斯耐热试验Martensite 马氏体Mullen bursting strength tester密廉式破裂强度试验机Nol ring test 诺尔环试验normal distribution 常态分配ozone resistance test 抗臭氧试验Pareto diagram 柏拉图peeling test 剥离试验pinhole test 针孔试验机rattler test 磨耗试验Rockweel hardness test 洛氏硬度试验Rockweel hardness 洛氏威尔硬度Rolinx process 罗林克斯射出压缩成形法Rossi-peakes flow test 罗西皮克斯流动试验sampling inspection 抽样检查scratch hardness 抗刮硬度shore hardness 萧氏硬度spiral flow test 螺旋流动试验surface abrasion test 表面磨耗试验Taber Abraser 泰伯磨耗试验机tensile impact test 拉伸冲击试验tensile strength 抗拉强度tension test 张力试验thermal shock test 冷热剧变试验torsion test 扭曲试验Ubbelohde viscometer 乌别洛德黏度计Vicat indentation test 维卡针压陷试验Vickers hardness test 维氏硬度试验warpage test 翘曲试验weatherometer 人工老化试验机Weissenberg effect 威森伯格回转效应砂轮用语abrasive 砂轮Al2O3 氧化铝balance 平衡bond 结合borazon 氧化硼立方晶buffing wheel 抛光布轮diamond 钻石dresser 砂轮整修机dressing 修整endless grinding belt 循环式研磨带finishing allowance 加工余量grain 磨粒grinding disc 研磨盘mesh 网筛目parameter 参数resinoid grinding wheel 半树脂型砂轮slitting 切缝量vitrified 陶瓷的wheel 旋转机械设计及周边其他用语assembly drawing 装配图auto tool change cycle 自动换刀时间周期beam 横梁bending moment 弯矩bending stress 弯曲应力bottoming 底靠buckling 纵弯曲chamfering 去角斜切channel 凹槽chattering 颤动check point 查核点chip 切屑chip conveyor 排屑输送机coefficient of friction 摩擦系数compact 小型的cooling pipe 冷却管coupon 试样胚deflection 挠曲量distortion 扭曲变形draft taper 拔模锥度draw out 拉拔fit tolerance 配合公差flexible rigidity 弯曲刚性gas vent 气孔hatching 剖面线heater cooler 加热器冷却装置hook cavity 钩穴inching 寸动lug 凸缘maintenance 维修保固metallurgy 冶金学notch effect 切口效果out of roughness 真圆度performance 动作性能pit 坑plane strain 倒角应力plug mill 蕊棒轧管机repeated load 重覆载荷sand paper 砂纸shift 偏移shrink fit 热压配合shrinkage hole 缩孔sinking 凹陷sketch 草图spalling 剥落straightness 直度submarine 深陷式surface roughness 表面粗度tapping 攻螺丝thermocouple 热电耦torsion load 扭转载荷toughness 韧性tracing 描图under cut 凹割业务与贸易关连用语accept order 接受订货account 帐户after service 售后服务amendment 修正annual sales 年销售额at sight 见票即付balance 余额bank draft 汇票bargain goods 廉价品batch 批次bid 出价bid sales 投标买卖bill of landing 提单bills receivable 应收票据brand 品牌bulk cargo 散装货business transaction 商业交易buyer 买方carbon copy 打字副本cargo collection 揽货carton 纸箱cash in advance 预付现金catalogue 型录cheque 支票CLF 运费保险费在内价格claim 索赔clearance goods 清仓品commision 佣金commission 批发商complain 抱怨container 货柜correspondence bank 往来银行cost 成本cost and freight; C&F 含运费价格custom broker 报关行customer 客户D/A 承兑交单D/P 付款交单deferred payment 分期付款deferred shipment 分期装运delivery on spot 当场交货delivery time 交期delivery order 交货单discount 折扣discount on draft 贴现documentary draft 跟单汇票down payment 订金enclosure 附件endorsement 背书exhibition 展览会export 出口factory visit 工厂参观favourable price 合宜价格foreign exchange 外汇free on board 船上交货价idea price 希望价格import 进口Japanese Industrial 日本工业规格invoice 发票L/C 信用状margin 利润market 市价net weight 净重no payment 拒绝付款odd item 零头offer 报价open account 交互计算order 订单over looked 疏漏packing 包装pamphlet 小册子partial shipment 分批装船patent 专利paying price 合算价格payment method 付款方式port of destination 目地港port of trans-shipment 转口港price 价格price descending 减价price rising 涨价procurement 采办prompt delivery 即时交货purchase 购入purchasing agent 采购代理商quotation 报价单rebate 回扣reference 查询remittance 汇款repeat order 追加订货request letter 请求函rumor 风评second hand goods 二手货shipper 货主shipping 装船shipping mark 麦头shipment 出货sold out 卖完sole agent 总代理商special discount 特别折扣specification 规格sample order 指样订货standing 信用情形storage charge 仓租subcontract 外包subject to final confirmation 有待确认之报价supplier 供应商T/T 电汇tie-in sale 搭售trade fair 商展会trans-shipment 转运transferred 已转运wharf 码头A 3D coordinate measurement 三次元量床3D modeling 三次元模拟aberration 色差abnormal glow 不规则辉光放电abrasive 砂轮access 通路account 帐户accretion 炉瘤accurate die casting 精密压铸acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth activator 活化剂acetylene 乙炔adjustable spanner 活动扳手aerator 松砂机ageing 老化处理air hardening 气体硬化airless plasting cleaning 离心喷光air patenting 空气韧化air permeability test 透气性试验air set mold 常温自硬铸模air vent valve 通气阀all core molding 集合式铸模alloy tool steel 合金工具钢allround die holder 通用模型aluminium alloy 铝合金钢amendment 修正ampere 电流安培anchor pin 锚梢angle cutter 角铣刀angle welding 角焊angular pin 角梢breathing 排气caulking compound 填隙料cell 气孔cold slug 半凝式射出colorant 著色剂color matching 调色compound 混合料copolymer 共聚合体cull 残料废品cure 凝固化cryptometer 不透明度仪daylight 开隙dry cycle time 空料试车周期时间ductility 延性elastomer 弹性体extruded bead sealing 压出粒涂层法feed 供料filler 充填剂film blowing 薄膜吹制法floating platen 活动模板foaming agent 发泡剂gloss 光泽granule 颗粒料gunk 料斗hot mark 热斑hot stamping 烫印injection nozzle 射出喷嘴injection plunger 射出柱塞injection ram 射出冲柱isomer 同分异构物kneader 混合机leveling agent 匀涂剂lubricant 润滑剂matched die method 配合成形法mould clamping force 锁模力mould release agent 脱模剂nozzle 喷嘴oriented film 取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂plunger 压料柱塞porosity 孔隙率post cure 後固化premix 预混料purging 清除reciprocating screw 往复螺杆resilience 回弹性resin injection 树脂射出法rheology 流变学sheet 塑胶片shot 注射shot cycle 射出循环slip agent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性void content 空洞率塑胶原料acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CA cellulose acetate butyrate 醋酸丁酸纤维素CAB composite material 复合材料cresol resin 甲酚树CF dially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑胶epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetate copolymer乙烯-醋酸乙烯EVA ethylene-vinlacetate copolyme醋酸乙烯共聚物EVA expanded polystyrene 发泡聚苯乙烯EPSfiber reinforcement 纤维强化复合材料high density polyethylene 高密度聚乙烯HDPE high impact polystyrene 高冲击聚苯乙烯HIPS high impact polystyrene rigidity高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MF nitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑胶polyacrylic acid 聚丙烯酸PAP 耐龙PA 聚对苯二甲酸丁酯PBT 聚碳酸酯PC 聚乙二醇PFG 聚氧化乙烯PEO 聚乙醇对苯PETP 聚甲基丙烯酸甲酯PMMA 聚缩醛POM 聚硫化亚苯polyphenyleneoxide 聚苯醚PPO 聚丙烯PP 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PE polyurethane 聚氨基甲酸酯PU polyvinylacetate 聚醋酸乙烯PVAC polyvinylalcohol 聚乙烯醇PVA polyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物silicone resin 矽树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑胶unsaturated polyester 不饱和聚酯树脂成形不良用语aberration 色差atomization 雾化bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕hair crack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮摺叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱摺surging 波动sweat out 冒汗torsion 扭曲]warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
細長線狀之突出成形。
旋鍛加工(swaging)
材料承受輪流式壓縮面朝橫方向擴展。
刻印加工(marking)
材料表面刻印細線文字或圖案。
定寸加工(sizing)
材料受微量壓縮，消除變形或使厚度精度提高。
機械加工名詞中英文對照(1)
序號
中文
英文
序號
中文
英文
1
衝壓加工
Stamping(press working)
Bulging
壓縮加工
Compressing
浮花壓制加工
Embossing
精整加工
Finishing
折疊加工
Folding
壓痕加工
Indenting
百葉窗板加工
Louvering
刻印加工
Marking
頸縮加工
Necking
二次精衝加工
Restriking
壓延加工
Rolling
矯正加工
Sizing
割縫加工
43
凸緣成形
Flanging
2
衝床
Press
44
孔凸緣成形
Hole flanging
3
溜塊
Ram
45
壓印加工
Coining
4
承塊
Bolster
46
鍛粗加工
Upsetting
5
衝壓模具
Stamping die
47
引縮加工
Ironing
6
剪應力
Shear stress
48
旋鍛加工
Swaging
7
抗剪強度
在模具內強制壓縮成形。
異形引伸
不規則形狀工件之引伸。
鍛粗加工(upsetting)
棒材軸方向之壓縮成形。
拉張成形
利用材料之伸長性之成形加工。
壓凹加工(indenting)
材料的一部分被衝頭壓凹。
縮頸成形(necking)
圓筒件或管件之端部形狀縮小。
引縮加工(ironing)
將引伸件璧部或管件厚度薄化，表面良好且光划。
模穴(模仁)
Cavity
角梢
Angular pin
心型
Core
防皺壓板
Blank holder
衝模板
Die plate
上下模板
Bolster
合模板(定位梢)
Dowel pin
托架
Bracket
脫模器
Ejector
模穴托板
Cavity retainer plate
頂出板
Ejector plate
夾模器
模具常用刀具與工作法用語
帶式打磨機
Belt sander
凹面銑刀
Concave cutter
凸形銑刀
Convex cutter
十字接頭
Cross joint
刀角
Nose angle
鉗子
Pinchers
劃線
Scribing
直角尺
Square
脫模鉗
Wiper
各種衝模加工關連用語
壓凸加工
Belling
撐壓加工
Master graphite
脈衝
Pulse
銳角邊
Sharp edge
加工餘量
Working allowance
模具加工方法
面車削
facing
銼刀修潤
Filing
研磨修潤
Lapping
粗切削
Rough machining
逆銑加工
Up cut milling
砂輪用語
砂輪
Abrasive
鑽石
Diamond
Land
導梢
Guide pin
活動襯套
Loose bush
引導柱
Guide post
分模線
Parting line
內柱塞
Inner plunger
針尖澆口
Pin gate
嵌件
Insert
推桿
Pusher
定位環
Locating ring
流道
Runner
塑膠模座
Mold base
滑塊
Slide
導銷
Pilot pin
錐度車削
Taper turning
螺紋切削
Thread cutting
超音波加工
Ultrasonic machining
機械加工相關名詞解釋
1
加工類型
加工名稱
加工特徵
加工類型
加工名稱
加工特徵
衝切加工
切 斷(cutting)
以一對切刃切斷，不產生衝切廢料，毛頭方向左右相反。
衝切加工
衝 孔(piercing)
Slitting
線割、放電加工關連用語
凸緣
Flange
電極臂
Horn
搖臂
Traverse
模具工方法
滾筒
Barrel
壓花加工
Embossing
卷邊加工
Hemming
滾齒加工
Hobbing
搖動加工
Joggling
刨削加工
Planing
拋亮光
Polishing
鉸孔修潤
Reaming
切縫切削
Slotting
正弦量規
Sine bar
觸針
Stylus
表面處理關連用語
偏析
Segregation
均熱處理
Soaking
表面硬化處理
Surface hardening
回火脆性
Temper brittleness
調質處理
Thermal refining
變態
Transformation
真空氮化
Vacuum nitriding
母模或衝頭附R角，可得良好的剪切面。
刮光加工(shaving)
制品胚件或孔之微量切削，可得良好的剪切面。
成形加工
V、L彎曲(bending)
利用v形衝頭或平直衝頭使胚件成V或L形狀。
成形加工
浮壓成形(embossing)
自由形狀之淺狀成形，使具花紋狀。
U彎曲
制品兩側同一方向彎曲呈U形。
肋條成形(ribbing)
衝頭
Punch
注道襯套
Sprue bushing
回位梢
Return pin
剝料板
Stripper plate
頭塞
Screw plug
拔錐梢
Taper pin
間隔塊
Spacer block
模具常用之工作機械
搪孔機
Boring machine
CNC銑床
CNC milling machine
仿形磨床
Copy grinding machine
Gauge plate
測高規
Height gauge
內卡鉗
Inside calipers
內分釐卡
Inside micrometer
平台
Levelling block
測微計
Micrometer
游標卡尺
Nonius
半徑
Radius
環規
Ring gauge
卡模
Snap gauge
直角尺
Square master
Die clamper
頂出襯套
Ejector sleeve
衝模壓座
Die set
引導襯套
Guide bushing
拔模錐度
Draft
導板
Guide plate
頂出梢
Ejector pin
導軌
Guide rail
頂出桿
Ejector rod
內衝頭
Inner punch
環首螺栓
Eye bolt
合模平坦面
Cylindrical grinding machine
治具搪孔機
Jig boring machine
靠模銑床
Multi model miller
龍門鉋床
Planer
牛頭鉋床
Shaper
轉塔車床
Turret lathe
檢驗量測工具用語
比測儀
Comparator
壓力計
Monometer
內徑儀
Passimeter
封閉形狀之全周衝切、衝切部分是廢料。
分 斷(parting)
材料或半制品之中間切斷，毛頭方向左右相同。
切 邊(trimming)
成形件邊緣之衝沏整外形。
下 料(blanking)
封閉形狀之全周下料。
衝缺口(notching)
開放形狀之衝切使材料或半制品邊側有缺口。
機械加工相關名詞解釋
2
加工類型
加工名稱
Shot peening
燒結處理
Sintering
軟化退火
Softening
矯直退火
Straightening annealing
應力消除退火
Stress relieving
深冷處理
Subzero treatment
回火
Tempering
軟氮化處理
Tufftride proccss
真空滲碳氮化
Vacuum carbonitriding
Austenite
染黑法
Blackening
磷酸鹽皮膜處理
Bonderizing
化學蒸鍍
Chemical vapor deposition