您的位置：360文档中心› MAX235EPG+G36中文资料

MAX235EPG+G36中文资料

合集下载

MX-3、 MX-5、 MMX-6、 PX-7测厚仪使用手册

MX-3、 MX-5、 MMX-6、 PX-7测厚仪使用手册

MX-3、MX-5、MMX-6、PX-7 测厚仪使用手册目录第一章MX-5测厚仪使用指南 (1)第二章MX-3测厚仪使用指南 (12)第三章MMX-6测厚仪使用指南 (12)第四章PX-7测厚仪使用指南 (13)第一章 MX-5测厚仪使用指南简介MX-5是精密的超声波测量仪器，可单边测量物体的厚度，但没有不去除表面涂层或漆层测量金属基体厚度的功能。

显示精度可达0.01mm。

本手册共分2个部分。

第一部分为键盘功能，显示和仪器操作；第二部分为应用及不同材料的声速。

操作键盘功能ON/OFF键为开关键。

开机后，仪器先进行自检显示。

一秒后，显示软件版本号，然后显示“0.00”，表明仪器可以使用。

MX-5关机后，可保存其所有设置。

如果5分钟不做任何操作，将自动关机。

PRB0键用于探头和仪器的调零。

- 1 -CAL键用来进入和退出MX-5校验模式。

该模式用来调节厚度值或声速值，可直接输入声速或通过样块厚度值计算某种材料的声速。

▲键有两个功能，当仪器处于标定状态时，该键用来增加厚度值或声速值。

因为有自动重复功能，一直按着该键数值将会加速增加。

当不处于标定状态时，▲键将用于开启或关闭扫查功能。

▼键有两个功能，当仪器处于标定状态时，该键用来减少厚度值或声速值.因为有自动重复功能，一直按着该键数值将会加速减少。

当不处于标定状态时，▼键将用于选择背景灯的3种工作状态：ON（常开）、OFF（常关），AUTO（自动，在测量时背景灯点亮，不测量时背景灯关闭以节省电源）。

SEND键用来将测量的厚度值通过底部的RS232接口传送到计算机或其它外部存储器。

ALRM键有两个作用：一个是用来和开关键联合使用，开启和关闭声音报警功能（在关机状态下按住该键并按开机键）；另一个功能是进入或退出报警功能。

- 2 -DIFF键用于开启或关闭差值功能。

IN/MM键用于在公/英制间转换。

显示屏显示数值及不同的设置。

通常显示最后一个测量值。

此外，电池电量不足时，屏幕开始闪动，应该更换电池。

MAX232中文

MAX232中文

+5V供电、多通道RS-232驱动器、接收器详细介绍MAX220-MAX249包括4个部分:双路电荷泵DC-DC电压转换器、RS-232驱动器、RS-232接收器，以及接收器与发送器使能控制输入。

双路电荷泵电压转换器MAX220-MAX249内部有两个电荷泵，将+5V转换为+10V（空载），为RS-232驱动器提供工作电压。

第一个转换器利用电容C1将+5V输入加倍，得到V+输出端C3上的+10V；第二个转换器利用电容C2将+10V转换为V-输出端C4上的-10V。

可以从+10V（V+）和-10V（V-）输出端获取少量的电源功率，为外部电路供电；但MAX225与MAX245- MAX247例外，因为它们不提供这些引脚，V+与V-未经稳压，所以输出电压会随负载电流的增大而下降。

当V+、V-为外部电路提供电流时，注意不要因为所加载的原因使V+、V-低于EIA/TIA-232E驱动端输出电压最小值+5V的限制。

使用MAX2222、MAX225、MAX230、MAX235、MAX236、MAX240、MAX241以及MAX245- MAX249上的关断功能时，应避免V+与V-为外部电路供电。

这些器件关断时，V-降至0V，V+降至+5V。

对于那些能够将+10V外部电源提供到V+引脚（而不是使用内部电荷泵来产生+10V）的应用，一定不要安装电容C1，并且必须将SHDN引脚连接至Vcc，这是应为在关断模式下V+被内部连接到Vcc。

RS-232驱动器如果负载是标称值为5KΩ的RS-232接收器，并且Vcc=+5V时，驱动器输出电压摆幅的典型值为+8V。

输出摆幅确保符合EIA/TIA-232E和V.28规范，该规范要求在最糟糕的情况下能够满足+5V驱动器输出电压最小值的要求，其中包括3KΩ的负载电阻最小值、Vcc=+4.5V以及最高工作温度。

空载是驱动器输出电压范围是（V+-1.3V）至（V-+0.5V）.输入门限兼容与TTL和COMS逻辑。

锐科 1000-1500W 连续光纤激光器 用户手册说明书

锐科 1000-1500W 连续光纤激光器 用户手册说明书

高性能1000-1500W连续激光器说明书武汉锐科光纤激光技术股份有限公司Wuhan Raycus Fiber Laser Technologies Co., Ltd.目录1 安全信息 (1)1.1 安全标识 (1)1.2 激光安全等级 (1)1.3 安全标识 (2)1.4 光学安全 (3)1.5 电学安全 (3)1.6 其他安全注意事项 (3)2 产品介绍 (4)2.1 产品特性 (4)2.2 型号说明 (4)2.3 装箱清单 (5)2.4 开箱及检查 (5)2.5 运行环境 (5)2.6 注意事项 (7)2.7 产品性能 (7)3 安装 (10)3.1 整机尺寸图 (10)3.1.1高性能1000-1500W连续激光器整机尺寸 (10)3.2 输出光缆的尺寸与安装 (11)3.2.1高性能1000-1500W连续激光器输出光缆 (11)3.3 冷却系统安装与要求 (12)3.4 安装注意事项 (13)4 产品使用 (15)4.1 前面板 (15)4.2 后面板 (15)4.3 电源连接 (16)4.4 接口定义 (16)4.4.1控制接口 (16)4.4.2 RS-232串口 (18)4.4.3以太网TCP/IP接口及连接步骤 (19)4.7 激光器的上位机功能 (22)4.7.1控制界面 (23)4.7.2日志界面 (24)4.7.3关于 (24)4.7.4语言选择 (25)4.7.5授权 (25)4.7.6模式选择 (26)4.7.7主控模块 (26)4.7.8电源监控 (27)4.8 控制模式选择 (28)4.8.1控制模式接线图 (28)4.8.2单机模式（内控模式）（顺序接上4.6） (29)4.8.3外控模式（顺序接上4.6） (29)4.8.4 AD模式 (30)4.8.5控制时序图 (31)4.8.6红光控制 (32)4.9 关闭操作顺序 (33)4.10 蓝牙APP操作说明 (33)4.10.1登录 (33)4.10.2连接 (33)4.10.3设备 (35)4.10.4 我的页面 (38)4.10.5软件介绍 (40)4.10.6工作流程 (40)5 常见警及处理措施 (41)5.1 告警显示 (41)5.2 告警处理 (41)6 质保及返修、退货流程 (44)6.1 一般保修 (44)6.2 保修的限定性 (44)6.3 技术支持及产品维修 (44)1安全信息感谢您选择锐科光纤激光器，本用户手册为您提供了重要的安全、操作、维护及其它方面的信息。

深川SVF-G7变频器使用说明书用户手册

深川SVF-G7变频器使用说明书用户手册
3.2 电气安装 ............................................................................................... 40 3.2.1 外围电气元件选型指导................................................................ 40 3.2.2 外围电气元件使用说明................................................................ 43 3.2.3 接线方式 ....................................................................................... 45 3.2.4 主回路端子及接线........................................................................ 46 3.2.5 控制端子及接线 ........................................................................... 47
2.15.1 日常保养 ..................................................................................... 34 2.15.2 定期检查 ..................................................................................... 35 2.15.3 变频器易损件更换...................................................................... 35 2.15.4 变频器的存贮 ............................................................................. 36 2.15.5 变频器的保修说明...................................................................... 36 2.16 选型指导 ............................................................................................. 36

MICROMEGA 高精度过程控制器说明书

MICROMEGA 高精度过程控制器说明书

CN77000 R300和R500控制器,图片中含RHS-43孔锯, 易于钻圆孔。

有关订购信息, 请参见最后一页。

CN77333-A2 NEMA 12款方形开孔。

CN77533 NEMA 4方形开孔。

图片为实际尺寸。

1⁄16 DIN MICROMEGA ®自动调谐PID温度/过程控制器U 高精度：±0.5°C (0.9°F), 读数的0.03% U品质优秀, 还有5年保修支持 U 通用输入—过程电压/电流、热电偶、RTD U 双4位数字LED 显示屏和指示器, 用于显示输出和报警状态 U 可选RS232或RS485, OMEGA ® 协议U 继电器、SSR 、DC 脉冲、0 ~ 10 V, 以及 0 ~ 20 mA 输出类型 U 斜坡到设定值功能 U 通用电源, 90 ~ 250 Vac 或Vdc U 双输出和双报警功能U 隔离模拟输出或远程设定值可选将方形控制器放置于圆孔中！高精度、高品质MICROMEGA ®控制器在过程控制中提供无与伦比的灵活性。

每台设备均允许用户从10个热电偶类型（J 、K 、T 、E 、R 、S 、B 、C 、N 和JDIN ）、Pt RTD （100、500或1000 Ω, 385或392曲线）或者模拟电压或电流输入中选择输入类型。

 电压/电流输入可完全扩展到各工程单位，可选择小数点，是压力、流量或其他过程输入的理想之选。

MICROMEGA ®控制器具有大型双LED 显示屏，采用前面板配置，可选温度/过程输入，并接受90 ～ 250 Vac 或Vdc 通用电源。

提供单和双输入配置，CN77000系列适用于继电器、SSR 、DC 脉冲或模拟电压或电流输出。

单报警是标准配置。

可选项包括第二报警、 RS232、RS485、模拟输出以及远程设定值可选。

“300”系列控制器有许多特色，更大，紧凑型1⁄4 DIN 控制器，1⁄16 DIN 尺寸。

航盛维修手册统一版

航盛维修手册统一版

www. hangsheng- sh. com
3.3.2.3 车内部半球摄像头................................................................28 3.3.2.3.1 车内部半球摄像头参数.....................................................28 3.3.2.3.2 车内部半球摄像头尺寸图.................................................28 3.3.2.3.3 车内部半球摄像头接口定义.............................................29 3.3.3 连接线参数 .............................................................................. 29 3.3.4 控制盒尺寸 .............................................................................. 29 3.3.5 系统连接总成图....................................................................... 29 3.4 故障排除指导 ..................................................................................... 30 3.5 注意事项 ............................................................................................ 30 影音类 ............................................................................................................... 31 4 高清播放器（固态存储）.......................................................................... 31 4.1 功能描述 ............................................................................................. 31 4.2 系统组成 ............................................................................................. 31 4.2.1 产品图示 .................................................................................. 31 4.2.2 系统组成图 .............................................................................. 32 4.2.3 整机接线图 .............................................................................. 32 4.3 技术参数 ............................................................................................. 33 4.3.1 性能及技术参数....................................................................... 33 4.3.2 面板及定义 .............................................................................. 33 4.4 故障排除及维护指导.......................................................................... 34 4.4.1 故障排除 ................................................................................. 34 4.4.2 日常维护保养.......................................................................... 34 5 液晶显示器 ................................................................................................. 35 5.1 功能描述 ............................................................................................. 35 5.1.1 功能介绍：.............................................................................. 35 5.2 系统组成 ............................................................................................. 35

美好暖和的商品说明书：美国好曼晟制造公司RP-658B维修部件

美好暖和的商品说明书：美国好曼晟制造公司RP-658B维修部件

REPAIR PARTSRP-658BThis manual is to be used by qualified technicians only.This manual replaces RP-658A.© 2011-2013 Goodman Manufacturing Company, L.P. ◊ 5151 San Felipe, Suite 500 ◊ Houston, TX 77056August 2013*PD14 Dual Fuel Package UnitsAPD1424070M41AA APD1424070M41BA APD1430090M41AA APD1430090M41BA APD1436090M41AA APD1436090M41BA APD1437090M41AA APD1442115M41AA APD1442115M41BA APD1448115M41AA APD1448115M41BA GPD1424070M41AA GPD1424070M41BA GPD1430090M41AA GPD1430090M41BA GPD1436090M41AA GPD1436090M41BA GPD1437090M41AA GPD1442115M41AA GPD1442115M41BA GPD1448115M41AA GPD1448115M41BAImportant Information For assistance within the U.S.A. contact:Goodman Company, L.P.For assistance outside the U.S.A. contact:IndexFunctional Parts List Rev B: Addition of 3 Ton models with increased efficiencyIllustration and Parts......................................................................................................................................................................................................Views shown are for parts illustrations only, not servicing procedures.AR - As Required NA - Not Available NS - Not Shown00000000 - See NoteQTY - Quantity Example (QTY 3) (If Quantity not shown, Quantity = 1)M - Model Example (M1) (If M Code not shown, then part is used on all Models)Text Codes:ExampleM1 - Model#1 M2 - Model#2 M3 - Model#3Expanded Model Nomenclature:Goodman Manufacturing Company, L.P. is not responsible for personal injury or property damage resulting from improper service. Review all service information before beginning repairs.Warranty service must be performed by an authorized technician, using authorized factory parts. If service is required after the warranty expires, Goodman Manufacturing Company, L.P. also recommends contacting an authorized technician and using authorized factory parts.Goodman Manufacturing Company, L.P. reserves the right to discontinue, or change at any time, specifications or designs without notice or without incurring obligations. 2Consumer Affairs DepartmentGoodman Manufacturing Company, L.P.7401 Security Way Houston, Texas 77040877-254-4729-Telephone 713-863-2382-FacsimileInternational DivisionGoodman Manufacturing Company, L.P.7401 Security Way Houston, Texas 77040713-861-2500-Telephone 713-863-2382-Facsimileg g 4 - 153RP-658BFunctional Parts PartNo:Description:0130M0002524V RELAY10735102BECKETT BURNER (QTY A/R)D6723303S BLOWER WHEEL (M3, M4, M5, M6, M7, M14,M15, M16, M17, M18)B1368058BLOWER WHEEL 10 X 8 (M1, M2, M12, M13) B1368000BLOWER WHEEL 11 X 10 (M8, M9, M10, M11,M19, M20, M21, M22)CAP050400440RT CAPACITOR 5/40/440V (M1, M2, M3, M4, M12,M13, M14, M15)CAP050450440RT CAPACITOR 5/45/440V (M5, M6, M7, M8, M9,M10, M11, M16, M17, M18, M19, M20, M21,M22)ZP21K5EPFV130COMP,21300,208/230/60/1 (M1, M2, M12, M13) ZP34K5EPFV130COMP,34500,208/230/60/1 (M8, M9, M19, M20) ZP25K5EPFV130COMPRESSOR 25200, 208/230/60/1 (M3, M4,M14, M15)ZP29K5EPFV130COMPRESSOR 29000, 208/230/60/1 (M7, M18) ZP31K5EPFV130COMPRESSOR 31100, 208/230/60/1 (M5, M6,M16, M17)ZP39K5EPFV130COMPRESSOR 39000, 208/230/60/1 (M10,M11, M21, M22)0131M00429COND MOTOR 1/4 HP, 1 SP, 6 PL (M8, M9,M10, M11, M19, M20, M21, M22)0131M00061COND MOTOR 1/4 HP, 1 SP, 8 PL (M3, M4,M5, M6, M7, M14, M15, M16, M17, M18)0131M00009P COND MOTOR 1/6 HP, 1 SP, 8 PL (M1, M2,M12, M13)CONT1P025024V CONTACTOR 25 AMP, 1P, 24V (M1, M2, M3,M4, M5, M6, M7, M12, M13, M14, M15, M16,M17, M18)CONT1P030024V CONTACTOR 30 AMP, 1P, 24V (M8, M9, M10,M11, M19, M20, M21, M22)0230G00005CRANKCASE HEATER SWITCH (M8, M9,M19, M20)B1086773FAN BLADE 22" (M1, M2, M12, M13)0150G00003FAN BLADE SWEPT-WING (M8, M9, M10,M11, M19, M20, M21, M22)0150G00002FAN BLADE SWEPT-WING (M3, M4, M5, M6,M7, M14, M15, M16, M17, M18)0130F00010FLAME SENSOR0151F00000P GAS VALVE - WHITE-RODGERS 2-STAGE 0163R00003HEATER, CRANKCASE 230V 40W (M8, M9,M19, M20)0130M00074HIGH PRESSURE SWITCH0130F00014IGNITOR10728344LIMIT SWITCH (M8, M9, M10, M11, M19, M20,M21, M22)10728343LIMIT SWITCH (M1, M2, M3, M4, M5, M6, M7,M12, M13, M14, M15, M16, M17, M18)0130M00075LOW PRESSURE SWITCH10123529MANUAL RESET LIMIT0131M00361MOTOR - 3/4 HP PROGRAMMED SELE (M10,M21)0131M00351MOTOR - 3/4 HP PROGRAMMED SELE (M8,M19)0131M00379MOTOR-1/2 HP PROGRAMMED SELEC (M3,M14)0131M00378MOTOR-1/2 HP PROGRAMMED SELEC (M5,M16)0131M00364MOTOR-1/2 HP PROGRAMMED SELEC (M1,M12)PCBDM133PCB, DEFROST CONTROLPCBAG127PCB, IGNITION, DSI, 2 STG 11112501PRESSURE SWITCH0131M00594PROGRAMMED MOTOR (M7, M18)0131M00434PROGRAMMED MOTOR (M2, M13)0131M00435PROGRAMMED MOTOR (M4, M15)0131M00436PROGRAMMED MOTOR (M6, M17)0131M00441PROGRAMMED MOTOR (M11, M22)0131M00440PROGRAMMED MOTOR (M9, M20)0151M00019REVERSING VALVE (M1, M2, M3, M4, M7,M12, M13, M14, M15, M18)0151M00021REVERSING VALVE (M5, M6, M8, M9, M10,M11, M16, M17, M19, M20, M21, M22)0130M00138TRANSFORMER, 208/230, 24VExpanded Model NomenclatureM1 - APD1424070M41AAM2 - APD1424070M41BAM3 - APD1430090M41AAM4 - APD1430090M41BAM5 - APD1436090M41AAM6 - APD1436090M41BAM7 - APD1437090M41AAM8 - APD1442115M41AAM9 - APD1442115M41BAM10 - APD1448115M41AAM11 - APD1448115M41BAM12 - GPD1424070M41AAM13 - GPD1424070M41BAM14 - GPD1430090M41AAM15 - GPD1430090M41BAM16 - GPD1436090M41AAM17 - GPD1436090M41BAM18 - GPD1437090M41AAM19 - GPD1442115M41AAM20 - GPD1442115M41BAM21 - GPD1448115M41AAM22 - GPD1448115M41BA3RP-658B Top Panel/Fan/Cabinet 4RP-658BTop Panel/Fan/CabinetRef.No:Part No:Description:Ref.No:Part No:Description:Image 1:FAN BLADE 22" (M1, M2, M12, M13)B108677311FAN BLADE SWEPT-WING (M3, M4, M5, M6, M7, M14, M15, M16, M17, M18)0150G0000211FAN BLADE SWEPT-WING (M8, M9, M10, M11, M19, M20, M21, M22)0150G0000311COND MOTOR 1/4 HP, 1 SP, 6 PL (M8, M9, M10, M11, M19, M20, M21, M22)0131M0042921COND MOTOR 1/4 HP, 1 SP, 8 PL (M3, M4, M5, M6, M7, M14, M15, M16, M17, M18)0131M0006121COND MOTOR 1/6 HP, 1 SP, 8 PL (M1, M2, M12, M13)0131M00009P 21GRILLE-FAN 0152G0000231PNL, TOP, PNT 0121G00156PDG 41SMALL SCREW (QTY 6)M022181751ACORN NUT 5/16 HEX BLACK (QTY 4)0163M00006P 61BLOWER DOOR 32" (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)20464801PDG 71BLOWER DOOR 40" (M8, M9, M10, M11, M19, M20, M21, M22)20464806PDG 71DOOR-EVAP/CONTROL 32 W/PAINT (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)20464802PDG81EVAP/CONTROL DOOR 40" (M8, M9, M10, M11, M19, M20, M21, M22)20464807PDG 81DOOR-HT EXCHANGE 32 (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)0121G00526DG 91DOOR-HT EXCHANGE 38 (M8, M9, M10, M11, M19, M20, M21, M22)0121G00527DG 91DOOR-COMPRESSOR 32 W/PAINT (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)20464804PDG101DOOR-COMPRESSOR 40 W/PAINT (M8, M9, M10, M11, M19, M20, M21, M22)20464809PDG 101LOUVERED PANEL, COND SIDE 32" (M12, M13, M14, M15, M16, M17, M18)20467701PDG 111LOUVERED PANEL, COND SIDE 32" (M1, M2, M3, M4, M5, M6, M7)20467701PLG 111LOUVERED PANEL, COND SIDE 40" (M19, M20, M21, M22)20467702PDG 111LOUVERED PANEL, COND SIDE 40" (M8, M9, M10, M11)20467702PLG 111UTILITY PANEL 32" (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)20466101PDG 121UTILITY PANEL 40" (M8, M9, M10, M11, M19, M20, M21, M22)20466102PDG 121PNL, DUCT, GAS 32.5" (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)0121G00442DG 131PNL, DUCT, GAS 40" (M8, M9, M10, M11, M19, M20, M21, M22)0121G00443DG 131SUPPORT POST 32" (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)0121G00460141SUPPORT POST 40" (M8, M9, M10, M11, M19, M20, M21, M22)0121G00462141LOUVERED PANEL, COND SIDE 32" (M12, M13, M14, M15, M16, M17, M18)20464401PDG 161LOUVERED PANEL, COND SIDE 32" (M1, M2, M3, M4, M5, M6, M7)20464401PLG 161LOUVERED PANEL, COND SIDE 40" (M19, M20, M21, M22)20464402PDG 161LOUVERED PANEL, COND SIDE 40" (M8, M9, M10, M11)20464402PLG 161BASE PAN RAIL (QTY 2)0121G00290181CORNER POST-COMP END 32" (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)20464201PDG251Image 1:CORNER POST-COMP END 40" (M8, M9, M10, M11, M19, M20, M21, M22)20464202PDG 251CORNER POST-HAIRPIN END 32" (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)20464301PDG261CORNER POST-HAIRPIN END 40" (M8, M9, M10, M11, M19, M20, M21, M22)20464302PDG 261FLUE HOOD (QTY 2)0121G00323271FLUE HOOD-LOWER 0121G00190281SCREEN-FLUE HOOD 20472601291GAS LINE GROMMET B1910012301ACCESS FITTING (QTY 2)B1373315NS CAP WITH O-RING (QTY 2)0163M00175NS FLUE HOOD ASSY 0270G00070NS PVC CONDUIT 8.25"177********F NS WASHER, BLACK (.50 OD .218ID) (QTY 4)0163M00005P NS WIRE HARNESS, FAN MOTOR (M1, M2, M8, M9, M10, M11, M12, M13, M19, M20, M21, M22)0259G00106NS WIRE HARNESS, FAN MOTOR (M3, M4, M5, M6, M7, M14, M15, M16, M17, M18)0259G00107NSExpanded Model Nomenclature M1 - APD1424070M41AA M2 - APD1424070M41BA M3 - APD1430090M41AA M4 - APD1430090M41BA M5 - APD1436090M41AA M6 - APD1436090M41BA M7 - APD1437090M41AA M8 - APD1442115M41AA M9 - APD1442115M41BA M10 - APD1448115M41AA M11 - APD1448115M41BA M12 - GPD1424070M41AA M13 - GPD1424070M41BA M14 - GPD1430090M41AA M15 - GPD1430090M41BA M16 - GPD1436090M41AA M17 - GPD1436090M41BA M18 - GPD1437090M41AA M19 - GPD1442115M41AA M20 - GPD1442115M41BA M21 - GPD1448115M41AA M22 - GPD1448115M41BA5RP-658B Partition Panels 6RP-658BPartition PanelsRef.No:Part No:Description:Ref.No:Part No:Description:Image 1:BLOWER DIVIDER (M1, M2, M12, M13)2046530571BLOWER DIVIDER 32" 10 X 9 (M3, M4, M5, M6, M7, M14, M15, M16, M17, M18)2046530471BLOWER DIVIDER 38" (M8, M9, M10, M11, M19, M20, M21, M22)0121G0017771FILLER PANEL, HEAT EXCHANGER 32" (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)20465201101FILLER PANEL, HEAT EXCHANGER 40" (M8, M9, M10, M11, M19, M20, M21, M22)20465202101PNL, PTN, 32.5" (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)0121G00360111PNL, PTN, 40" (M8, M9, M10, M11, M19, M20, M21, M22)0121G00361111EVAP/HEAT EXCHANGER DIVIDER 32" (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)20465501121EVAP/HEAT EXCHANGER DIVIDER 38" (M8, M9, M10, M11, M19, M20, M21, M22)20465502121FAN PARTITION SHELF20465701131FAN SURROUND 32" (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)20465801141SHIELD, HEAT EXCHANGER TUBES 20472501151DRAIN CHANNEL, SUCTION TUBE20496801161EVAP/BASEPAN BLOCK 32" (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)20463802221EVAP/BASEPAN BLOCK 40" (M8, M9, M10, M11, M19, M20, M21, M22)20463801221Effective July 2008 (serial codes 0807), single phase units will no longer be factory shipped with horizontal duct covers.For downshot applications, contact your local Goodman distributor.Expanded Model Nomenclature M1 - APD1424070M41AA M2 - APD1424070M41BA M3 - APD1430090M41AA M4 - APD1430090M41BA M5 - APD1436090M41AA M6 - APD1436090M41BA M7 - APD1437090M41AA M8 - APD1442115M41AA M9 - APD1442115M41BA M10 - APD1448115M41AA M11 - APD1448115M41BA M12 - GPD1424070M41AA M13 - GPD1424070M41BA M14 - GPD1430090M41AA M15 - GPD1430090M41BA M16 - GPD1436090M41AA M17 - GPD1436090M41BA M18 - GPD1437090M41AA M19 - GPD1442115M41AA M20 - GPD1442115M41BA M21 - GPD1448115M41AA M22 - GPD1448115M41BA7RP-658BBasepan/Blower Assembly 8RP-658BBasepan/Blower AssemblyRef.No:Part No:Description:Ref.No:Part No:Description:Image 1:TC SCREW 1.25" (QTY 3)M025056511MOTOR MOUNT BAND 0121M0003821MOTOR MOUNT ARM (QTY 3)B137685731BLOWER WHEEL (M3, M4, M5, M6, M7, M14, M15, M16, M17, M18)D6723303S 41BLOWER WHEEL 10 X 8 (M1, M2, M12, M13)B136805841BLOWER WHEEL 11 X 10 (M8, M9, M10, M11, M19, M20, M21, M22)B136800041MACHINE SCREW HWH 1/4-20 X 1-1/2 BZ B139332361BASEPAN, PACKAGE0121G0044471SINGLE COVER, DOWN DISCHARGE (QTY 2)0121G0014891LOCKNUT, NYLON, INSERT 1/4, 20B1393800101MOTOR - 3/4 HP PROGRAMMED SELE (M8, M19)0131M00351121MOTOR - 3/4 HP PROGRAMMED SELE (M10, M21)0131M00361121MOTOR-1/2 HP PROGRAMMED SELEC (M1, M12)0131M00364121MOTOR-1/2 HP PROGRAMMED SELEC (M5, M16)0131M00378121MOTOR-1/2 HP PROGRAMMED SELEC (M3, M14)0131M00379121PROGRAMMED MOTOR (M2, M13)0131M00434121PROGRAMMED MOTOR (M4, M15)0131M00435121PROGRAMMED MOTOR (M6, M17)0131M00436121PROGRAMMED MOTOR (M9, M20)0131M00440121PROGRAMMED MOTOR (M11, M22)0131M00441121PROGRAMMED MOTOR (M7, M18)0131M00594121AUXILIARY LIMIT, AUTO RESET20269903131BLOWER BLOCK-OFF (M3, M4, M5, M6, M7, M14, M15, M16, M17, M18)764742141BLOWER BLOCK-OFF 10 X 8 (M1, M2, M12, M13)764740141BLOWER CUT-OFF (M8, M9, M10, M11, M19, M20, M21, M22)1864703F 141AUXILIARY LIMIT BRACKET2509503F 151BLOWER HOUSING ASSY (11X10) (M8, M9, M10, M11, M19, M20, M21, M22)2539309161BLOWER HOUSING ASSY 10 X 8 (M1, M2, M12, M13)0271F00001P 161BLOWER HOUSING ASSY 10 X 9 (M3, M4, M5, M6, M7, M14, M15, M16, M17, M18)0271G0002416111 X 10 BLOWER MOUNTING (M8, M9, M10, M11, M19, M20, M21, M22)20463701171Expanded Model Nomenclature M1 - APD1424070M41AA M2 - APD1424070M41BA M3 - APD1430090M41AA M4 - APD1430090M41BA M5 - APD1436090M41AA M6 - APD1436090M41BA M7 - APD1437090M41AA M8 - APD1442115M41AA M9 - APD1442115M41BA M10 - APD1448115M41AA M11 - APD1448115M41BA M12 - GPD1424070M41AA M13 - GPD1424070M41BA M14 - GPD1430090M41AA M15 - GPD1430090M41BA M16 - GPD1436090M41AA M17 - GPD1436090M41BA M18 - GPD1437090M41AA M19 - GPD1442115M41AA M20 - GPD1442115M41BA M21 - GPD1448115M41AA M22 - GPD1448115M41BA9RP-658B Compresor/Tubing Assembly 10RP-658BCompresor/Tubing AssemblyRef.No:Part No:Description:Ref.No:Part No:Description:Image 1:COMP,21300,208/230/60/1 (M1, M2, M12, M13)ZP21K5EPFV13011COMP,34500,208/230/60/1 (M8, M9, M19, M20)ZP34K5EPFV13011COMPRESSOR 25200, 208/230/60/1 (M3, M4, M14, M15)ZP25K5EPFV13011COMPRESSOR 29000, 208/230/60/1 (M7, M18)ZP29K5EPFV13011COMPRESSOR 31100, 208/230/60/1 (M5, M6, M16, M17)ZP31K5EPFV13011COMPRESSOR 39000, 208/230/60/1 (M10, M11, M21, M22)ZP39K5EPFV13011TF SHOULDER SCREW (QTY 4)M022164131TUBING ASSY, EVAP COIL (M10, M11, M21, M22)0202G0028261TUBING ASSY, EVAP COIL (M1, M2, M12, M13)0202G0028361TUBING ASSY, EVAP COIL (M3, M4, M7, M14, M15, M18)0202G0031561TUBING ASSY, EVAP COIL (M8, M9, M19, M20)0202G0031661TUBING ASSY, EVAP COIL (M5, M6, M16, M17)1262643 61COND COIL TUBING ASSY (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)0201G0016491COND COIL TUBING ASSY (M8, M9, M19, M20)0201G0024291COND COIL TUBING ASSY (M10, M11, M21, M22)0201G0026091REVERSING VALVE (M1, M2, M3, M4, M7, M12, M13, M14, M15, M18)0151M00019111REVERSING VALVE (M5, M6, M8, M9, M10, M11, M16, M17, M19, M20, M21, M22)0151M00021111HIGH PRESSURE SWITCH0130M00074141HEATER, CRANKCASE 230V 40W (M8, M9, M19, M20)0163R00003171ACCUMULATOR (M1, M2, M3, M4, M7, M12, M13, M14, M15, M18)B1226206211ACCUMULATOR .875 (M5, M6, M8, M9, M10, M11, M16, M17, M19, M20, M21, M22)B1226207211BI-FLOW FILTER DRIER20485201241COMPRESSOR GROMMET (QTY 4)B1339533NS COMPRESSOR SCROLL HARNESS (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)0159G00002NSCOMPRESSOR SCROLL HARNESS (M8, M9, M10, M11, M19, M20, M21, M22)0159G00006NS CONTROL, DEFROST (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)0130M00099NS CONTROL, DEFROST (M8, M9, M10, M11, M19, M20, M21, M22)0130M00102NS CRANKCASE HEATER SWITCH (M8, M9, M19, M20)0230G00005NS DRAIN PAN-EVAP COIL 20464901DF NS DRAIN PAN-EVAP COIL 20464901DF NS EVAP DRAIN FITTING 20513001NS EVAP DRIP SHIELD 0121G00324NS LOW PRESSURE SWITCH 0130M00075NS SOLENOID COIL B1225022NS WIRE ASSY-9 CIRCUIT0259G00029NSExpanded Model Nomenclature M1 - APD1424070M41AA M2 - APD1424070M41BA M3 - APD1430090M41AA M4 - APD1430090M41BA M5 - APD1436090M41AA M6 - APD1436090M41BA M7 - APD1437090M41AA M8 - APD1442115M41AA M9 - APD1442115M41BA M10 - APD1448115M41AA M11 - APD1448115M41BA M12 - GPD1424070M41AA M13 - GPD1424070M41BA M14 - GPD1430090M41AA M15 - GPD1430090M41BA M16 - GPD1436090M41AA M17 - GPD1436090M41BA M18 - GPD1437090M41AA M19 - GPD1442115M41AA M20 - GPD1442115M41BA M21 - GPD1448115M41AA M22 - GPD1448115M41BAHeat Exchanger/Manifold/Gas ValveHeat Exchanger/Manifold/Gas ValveRef.No:Part No:Description:Ref.No:Part No:Description:Image 1:ID BLOWER0131G0000121ID BLOWER PLATE LRG 5 BRNR (M8, M9, M10, M11, M19, M20, M21, M22)0121G0021831ID BLOWER PLATE SML 3 BRNR (M1, M2, M12, M13)2046310231ID BLOWER PLATE SML 4 BRNR (M3, M4, M5, M6, M7, M14, M15, M16, M17, M18)2046310331PRESSURE SWITCH1111250141PART/TUBE ASSY 3B (M12, M13)2049070751PART/TUBE ASSY 3B (M1, M2)2049071051PART/TUBE ASSY 4B (M14, M15, M16, M17, M18)2049070351PART/TUBE ASSY 4B (M3, M4, M5, M6, M7)2049071151PART/TUBE ASSY 5B (M19, M20, M21, M22)2049070551PART/TUBE ASSY 5B (M8, M9, M10, M11)2049071351IGNITOR0130F0001471GAS VALVE - WHITE-RODGERS 2-STAGE 0151F00000P 81FLAME SENSOR0130F0001091MANIFOLD - 3 BRNR (M1, M2, M12, M13)20493103101MANIFOLD - 4 BRNR (M3, M4, M5, M6, M7, M14, M15, M16, M17, M18)20493104101MANIFOLD - 5 BRNR (M8, M9, M10, M11, M19, M20, M21, M22)20493106101BECKETT BURNER (QTY A/R)10735102111BURNER BRACKET 3B (M1, M2, M12, M13)20190411121BURNER BRACKET 4B (M3, M4, M5, M6, M7, M14, M15, M16, M17, M18)20190412121BURNER BRACKET 5B (M8, M9, M10, M11, M19, M20, M21, M22)20190413121MANUAL RESET LIMIT 10123529131ELBOW-FLUE LEFT 20484401141ELBOW-FLUE RIGHT20484402141ORIFICE SHIELD (M1, M2, M12, M13)11072202151ORIFICE SHIELD (M3, M4, M5, M6, M7, M14, M15, M16, M17, M18)11072203151ORIFICE SHIELD (M8, M9, M10, M11, M19, M20, M21, M22)11072204151SMALL SCREW (QTY 25)M022*******ID BLOWER PLATE GASKET LRG (M8, M9, M10, M11, M19, M20, M21, M22)20463001NS ID BLOWER PLATE GASKET SML (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)20462801NSORIFICE (QTY A/R)10716003NS Expanded Model Nomenclature M1 - APD1424070M41AA M2 - APD1424070M41BA M3 - APD1430090M41AA M4 - APD1430090M41BA M5 - APD1436090M41AA M6 - APD1436090M41BA M7 - APD1437090M41AA M8 - APD1442115M41AA M9 - APD1442115M41BA M10 - APD1448115M41AA M11 - APD1448115M41BA M12 - GPD1424070M41AA M13 - GPD1424070M41BA M14 - GPD1430090M41AA M15 - GPD1430090M41BA M16 - GPD1436090M41AA M17 - GPD1436090M41BA M18 - GPD1437090M41AA M19 - GPD1442115M41AA M20 - GPD1442115M41BA M21 - GPD1448115M41AA M22 - GPD1448115M41BAControl PanelControl PanelRef.No:Part No:Description:Ref.No:Part No:Description:Image 1:LIMIT SWITCH (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)1072834341LIMIT SWITCH (M8, M9, M10, M11, M19, M20, M21, M22)1072834441PCB, IGNITION, DSI, 2 STG PCBAG12751TRANSFORMER, 208/230, 24V0130M0013861CAPACITOR 5/40/440V (M1, M2, M3, M4, M12, M13, M14, M15)CAP050400440RT 71CAPACITOR 5/45/440V (M5, M6, M7, M8, M9, M10, M11, M16, M17, M18, M19, M20, M21, M22)CAP050450440RT 71CONTACTOR 25 AMP, 1P, 24V (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)CONT1P025024V 81CONTACTOR 30 AMP, 1P, 24V (M8, M9, M10, M11, M19, M20, M21, M22)CONT1P030024V 81PCB, DEFROST CONTROL PCBDM1339124V RELAY0130M00025111CAPACITOR STRAP 20520901NS WIRE HARNESS ASSY 0259G00101NS WIRE HARNESS ASSY 0259G00102NS WIRE HARNESS ASSY0259G00103NS WIRE HARNESS ASSY (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)0259G00104NS WIRE HARNESS ASSY (M8, M9, M10, M11, M19, M20, M21, M22)0259G00105NS WIRE HARNESS ASSY (M1, M2, M3, M4, M5, M6, M7, M12, M13, M14, M15, M16, M17, M18)0259G00108NS WIRE HARNESS ASSY (M8, M9, M10, M11, M19, M20, M21, M22)0259G00109NS WIRE HARNESS, 6 CIRCUIT 0259G00098NS WIRE HARNESS, 9 CIRCUIT 0259G00110NS WIRE HARNESS, ECONO0259G00099NS WIRE HARNESS, OUTDOOR THERMO0259G00100NSExpanded Model Nomenclature M1 - APD1424070M41AA M2 - APD1424070M41BA M3 - APD1430090M41AA M4 - APD1430090M41BA M5 - APD1436090M41AA M6 - APD1436090M41BA M7 - APD1437090M41AA M8 - APD1442115M41AA M9 - APD1442115M41BA M10 - APD1448115M41AA M11 - APD1448115M41BA M12 - GPD1424070M41AA M13 - GPD1424070M41BA M14 - GPD1430090M41AA M15 - GPD1430090M41BA M16 - GPD1436090M41AA M17 - GPD1436090M41BA M18 - GPD1437090M41AA M19 - GPD1442115M41AA M20 - GPD1442115M41BA M21 - GPD1448115M41AA M22 - GPD1448115M41BA。

海德遥控器说明书

海德遥控器说明书
接收器进入安全模式
以下的状况会导致接收器进入安全模式： • 信号干扰 • 发射器处于操作范围之外 • 急停按扭被启动 • 急停回路故障 • 电池电量不足
当接收器接收不到发射器信号时，接收器就 会自动进入安全模式。在安全模式下，接收 器将关闭所有被控组件的电源，并启动急停 功能。 BMS-2 接收器会显示“001”表示接收器进 入安全模式状况。
关闭发射器电源，如果操作人员要离 开现场，则必须带走电源钥匙。 2、 在进行装配、维护和修理工作之前， 一定要切断系统的电源。
要点：避免系统的损坏，在对机器的任何
部分进行焊接之前一定要切断接收器电 源。 3、 不要更换或改造该系统的任何安全功
能设备。 4、 在对机器进行操作之前，确认其无线
遥控系统的急停功能运行正常。
发射器的用法
在使用发射器时，应面对发射器操作面板， 确定你可以清晰的看到发射器上各个功能 的图标。不恰当的握法会导致机器的不正 确的操作。发射器配有的腰带或吊带，则 务必使用，从而减少操作压力并提高安全 性。
部分进行焊接之前一定要切断接受器电 源。
接收器安装说明
警告：如不按照该手册的要求去 安装，有可能会造成系统损坏、 人员伤害或机器损坏。请详细阅 读该手册上的安装要求。
以下是接收器螺丝孔的安装尺寸
安装接收器
寻找一个理想的安装接收器位置，以便于观 察接收器上的 LED 状态显示，以方便安装 调试以及避免接收器遭到外来的破坏。 接受器的外壳达到 IP65 防护等级（可防尘， 防水），所以恶劣天气等外界环境因素不是 选择安装位置时的主要考虑因素。
产品和系统资料
当您需要维护或者购买零配件等服务时，请 与代理商联系，您必须提供发射器和接受器 的详细系统资料。该资料粘贴于系统外壳 上，请勿私自损坏或移除。

电子芯片大全

电子芯片大全

号功能简述型号AD1380JDAD1380KDAD1671JQAD1672APAD1674ADAD1674JNAD202JNAD202JYAD204JNAD22100KTAD22105ARAD261BND-1AD2S99APAD420AN-32AD420AR-32AD421BNAD421BRAD515AJHAD515ALHAD517JHAD518JHAD521JDAD524ADAD526BDAD526JNAD532JHAD534JDAD534JHAD536AJDAD536AJHAD536AJQAD537JHAD537SHAD538ADAD539JNAD542JHAD545ALHAD546JNAD547JHAD548JNAD549JHAD549LHAD5539JNAD557JNAD558JNAD568JQ AD569JN AD570JD/+ AD574AJD AD574AKD AD578KN AD580JH AD580LH AD581JH AD582KD AD584JH AD584JN AD585AQ AD586JN AD586JQ AD586KN AD586KQ AD586KR AD587KN AD587KR AD588AQ AD589JH AD590JH AD590KH AD592AN AD592BN AD595AD AD595AQ AD598AD AD600XN AD602JN AD603AQ AD606JN AD607ARS AD620AN AD621AN AD622AN AD623AN AD623AR AD624AD AD625JN AD625KN AD626AN AD627AN AD629AN AD630JNAD636JDAD636JHAD637JQAD648JNAD650JNAD650KNAD652AQAD654JNAD654JRAD660ANAD6640AST AD6644AST AD667JNAD667KNAD669ANAD670JNAD676JDAD676JNAD676KDAD677ARAD677JDAD677JNAD678JDAD678KNAD679JNAD679KNAD680JNAD684JQAD693AQAD694AQAD694JNAD698APAD7008AP20 AD7008JP-50 AD704JNAD705JNAD706JNAD707AQAD707JNAD708AQAD708JNAD7111ABN AD7111LN AD711AQAD711JNAD711JRAD712JN AD713BQ AD713JN AD720JP AD7224KN AD7226KN AD7228ABN AD722JR-16 AD7237AAN AD7237JN AD7243AN AD7245AAN AD7249BN AD724JR AD73360AR AD734AQ AD736JN AD737AQ AD737JN AD7416AR AD741KN AD743JN AD744JN AD745JN AD75019JP AD7501JN AD7502JN AD7502KQ AD7503JN AD7506JN AD7507JN AD7510DIJN AD7510DIKN AD7512DIJN AD7512DIKN AD7520LN AD7523JN AD7524JN AD7528JN AD7528KN AD7533JN AD7535JN AD7537JN AD7541AKN AD7542JN AD7543KNAD7564BN AD7574JN AD7590DIKN AD7660AST AD7664AST AD767JNAD768ARAD7701AN AD7703AN AD7703BN AD7705BN AD7705BR AD7706BN AD7707BR AD7710AN AD7711AN AD7712AN AD7713AN AD7714AN-3 AD7714AN-5 AD7715AN-5 AD7715AR-5 AD7731BN AD7741BN AD7742BN AD7750AN AD7755AARS AD7777AR AD779JDAD780ANAD781JNAD7820KN AD7821KN AD7822BN AD7824BQ AD7824KN AD7837AN AD7845JN AD7846JN AD7847AN AD7856AN AD7862AN-10 AD7864AS-1 AD7865AS-1 AD7872AN AD7874ANAD7886JD AD7886KD AD7888AR AD7890AN-10 AD7891AP-1 AD7892AN-1 AD7895AN-10 AD790JNAD795JNAD797ANAD797ARAD8001AN AD8002AN AD8009AR AD8011AN AD8015AR AD8018AR AD8031AN AD8032AN AD8036AN AD8037AN AD8041AN AD8041AR AD8042AN AD8044AN AD8047AN AD8055AR AD8056AR AD8058AR AD8079AR AD8108AST AD8109AST AD810ANAD8111AST AD8115AST AD8116AST AD811ANAD811JRAD812ANAD812ARAD8131AR AD8138AR AD813ANAD813AR-14 AD815AYAD8170ANAD817ANAD8180AN AD8184AN AD818ANAD820ANAD822ANAD822AN-3V AD823ANAD824ANAD826ANAD827AQAD827JNAD828ANAD829JNAD8307AN AD8307AR AD8309ARU AD830ANAD830ANAD8313ARM AD8313ARM AD8320ARP AD834JNAD8350AR15 AD835ANAD8402AN-10 AD8403AN100 AD840JNAD843AQAD844ANAD845JNAD845KNAD847AQAD847JNAD847SQAD849JNAD8522AN AD8551AR AD8552AR AD8561AN AD8561AR AD8564AN AD8598AN AD9042AST AD9048JQ AD9049BRSAD9051BRSAD9057BRS-40 AD9057BRS-60 AD9058JJAD9059BRSAD9066JRAD9071BRAD9101ARAD9200ARSAD9203ARUAD9220ARAD9221ARAD9223ARAD9225ARAD9226ARSAD9240ASAD9243ASAD9260ASAD9280ARSAD9281ARSAD9283BRS-100 AD9283BRS-80 AD9288BRS-80 AD9300KQAD9483KS-100 AD9500BQAD9501JNAD9617JRAD9617JNAD9618JNAD9630ANAD9631ANAD96687BQAD9698KNAD9708ARUAD9709ASTAD9713BANAD9721BRAD9731BRAD9732BRSAD9750ARAD9752ARAD9760ARAD9762ARAD9764ARAD976CNAD976AAN AD9772AST AD977AAN AD977AN AD9801JCST AD9802JST AD9803JST AD9805JS AD9816JS AD9822JR AD9830AST AD9831AST AD9832BRU AD9850BRS AD9851BRS AD9852AST AD9852ASQ AD9853AS AD9854AST AD9854ASQ AD9901KQ ADG201AKN ADG201HSJN ADG211AKN ADG222AKN ADG333ABN ADG333ABR ADG408BN ADG409BN ADG411BN ADG417BN ADG419BN ADG431BN ADG436BN ADG441BN ADG442BN ADG506AKN ADG507AKN ADG508AKN ADG508FBN ADG509AKN ADG511BN ADG608BN ADG609BN ADG719BRM ADG736BRMADM690ANADM708ANADSP21060KS160 ADSP21060CZ-160 ADSP21062KS-160 ADSP2181KS-133 ADSP2181KST-133 ADUC812BS ADVF32KNADXL105JQC ADXL202AQC AMP02FPAMP04FPDAC08CPDAC8228FPOP07AZ/883COP07CPOP07CSOP176GPOP177GPOP27GPOP291GPOP295GPOP296GPOP297GPOP297GSOP37EPOP37GPOP495GPOP497GPOP77GPOP90GPOP97FPOP97FSPKD01FPREF02CPREF03GPREF192GPREF192GSREF194GPREF195GSREF43FZSMP04EPSMP08FPSSM2141PSSM2142PSSM2211P SSM2275P TMP03FS TMP04FS TMP36GT9 MAX038CPP MAX1044CPA MAX110ACPE MAX110BCPE MAX111BCPE MAX122BCNG MAX1232CPA MAX1242BCSA MAX125CEAX MAX134CPL MAX135CPI MAX139CPL MAX140CPL MAX1480BCPI MAX1480BEPI MAX1483CPA MAX1487CPA MAX1487ECPA MAX1488ECPD MAX1489ECPD MAX148BCPP MAX1490BCPG MAX158BCPI MAX1771CPA MAX1771CSA MAX180CCPL MAX186CCPP MAX187BCPA MAX189CCPA MAX191BCNG MAX192BCPP MAX197BCNI MAX202CPE MAX202CSE MAX202ECPE MAX202EESE MAX202EPE MAX207CNG MAX208CNG MAX232CPE MAX232CSEMAX235CPG MAX238CNG MAX238ENG MAX260BCHG MAX260BENG MAX261BCNG MAX280CPA MAX291CPA MAX292CPA MAX293CPA MAX294CPA MAX297CPA MAX301CPE MAX305EPE MAX306CPI MAX3080CPD MAX3082CPA MAX308CPE MAX309CPE MAX3100CPD MAX312CPE MAX313CPE MAX318CPA MAX319CPA MAX3218CPP MAX3223CPP MAX3232CPE MAX325CPA MAX333CPP MAX338CPE MAX339CPE MAX351CPE MAX354CPE MAX354CWE MAX354EPE MAX355CPE MAX355CWE MAX366CPA MAX367CPN MAX384CPN MAX391CPE MAX400CPA MAX4016ESA MAX4100ESA MAX4101ESA MAX4106ESAMAX4142ESD MAX4146ESD MAX419CPD MAX420CPA MAX427CPA MAX435CPD MAX436CPD MAX440CPI MAX441CPP MAX442CPA MAX4456CPL MAX453EPA MAX457EPA MAX458CPL MAX468CPE MAX470CPE MAX479CPD MAX480EPA MAX483CPA MAX485CPA MAX487CPA MAX487ECPA MAX487EEPA MAX488CPA MAX490ECPA MAX491CPD MAX491ECPD MAX501AENG MAX504CPD MAX505BCNG MAX506CPP MAX509BCPE MAX512CPD MAX515CPA MAX517BCPA MAX518BCPA MAX526DCNG MAX527DCNG MAX528CPP MAX530BCNG MAX531BCPD MAX532BCPE MAX536BCWE MAX538BCPA MAX543ACPA MAX551ACPAMAX619CPA MAX6225ACPA MAX6225AESA MAX6225BCPA MAX6225BCSA MAX622CPA MAX6250BCPA MAX633ACPA MAX638AEPA MAX639CPA MAX660CPA MAX662ACPA MAX667CPA MAX691ACPE MAX691CPE MAX705CPA MAX706CPA MAX708CPA MAX708CSA-T MAX709LEPA MAX712CPE MAX712EPE MAX713CPE MAX7219CNG MAX7219ENG MAX724CCK MAX726CCK MAX729CCK MAX730ACPA MAX733CPA MAX735CPA MAX736CPD MAX738ACPA MAX738AEPA MAX739CPD MAX739CWE MAX7400CPA MAX743CPE MAX743EPE MAX749CPA MAX750ACPA MAX756CPA MAX761CPA MAX764CPA MAX765CPA MAX766EPAMAX791CPE MAX807LCPE MAX810LEUR-T MAX813LCPA MAX813LEPA MAX818LCPA MAX860ISA MAX865EUA MAX866ESA MAX874EPA MAX875BCPA MAX882CPA MAX883CPA MAX883CSA MAX907CPA MAX910CNG MAX912CPE MAX913CPA MAX931CPA MAX934CPE MXD1210CPA LFC2LFC3LFC4LFC54LFC75F003F004(5G23)F005F006F007(5G24)F010F011F1550F1490F1590F157/AF253F741(F007)F741AF747OP-07OP111AF4741F101A/201AF301AF308F110/210 F310F118/218 F441F318F124/224 F324F148F248/348 F158/258 F358F1558F4558LF791LF4136 FD37/FD38 FD46LF082 LFOP37LF3140LF7650LZ1606LZ19001 LBMZ1901 LM741LM747OP-07LM101/201 LM301LM108/208 LM308LM110LM310LM118/218 LM318LM124/224 LM324LM148LM248/348 LM158/258 LM358LM1558 OP-27CP TL062TL072TL082TL084MC1458LF147/347LF156/256/356LF107/307LF351LF353LF155/355LF157/357LM359LM381CA3080CA3100CA3130CA3140CA3240CA3193CA3401MC3303MC3403LF411LF444µpc4558MC4741LM709LM725LM733LM748ICL7650ICL7660稳压器固定输出（正电压）稳压器78xx 系列 3端稳压器 5V 到 24V1A78Lxx 系列 3端稳压器 5V 到 24V 0.1A78Mxx 系列 3端稳压器 5V 到 24V 0.5A78Sxx 系列 3端稳压器 5V 到 24V 2A固定输出（负电压）稳压器79xx 系列 3端负电压稳压器 -5V 到 -24V 1A [110kb] 79Lxx 系列 3端负电压稳压器 -5V 到 -24V 0.1A [95kb]可调输出 - 常用稳压器LM117 1.2V... 37V 1.5A 正电压可调稳压器 [100kb] LM217 1.2V... 37V 1.5A 正电压可调稳压器 [100kb] LM317 1.2V... 37V 1.5A 正电压可调稳压器 [100kb] LM137 -1.2V...-37V 1.5A 负电压可调稳压器 [246kb] LM237 -1.2V...-37V 1.5A 负电压可调稳压器 [246kb]LM337 -1.2V...-37V 1.5A 负电压可调稳压器 [246kb] LM138 1.2V --32V 5-安培 可调LM338 1.2V -- 32V 5-安培 可调LM723 高精度可调 [136kb]L200 2 A / 2.85 to 36 V.可调 [166KB]TTL 逻辑电路 [LS - HC 或 HCT 系列]74LS0074LS0474LS0874LS1074LS1374LS1474LS2774LS3074LS3274LS4274LS4574LS4774LS9074LS9274LS9374LS12174LS15474LS19274LS19374HC23774LS37474LS390CMOS 逻辑电路4001400240074011401340164017402240234025402640284029404040464051405240534055 4056 4060 4066 4067 4068 4069 4071 4072 4075 4081 4082 4093 4511 4518 4583 4584晶体管小功率管2N9302N16132N2222A 2N34392N34402N39042N39062N54012N54152N54162N55502N55512N65152N49212N49222N4923 AF125 BC107 BC108 BC109 BC148 BC177 BC178 BC179 BC182 BC183 BC184BC214BC327BC301BC302BC303BC304BC328BC337BC338BC414BC416BC461BC516BC517BC546BC547BC548BC549BC550BC556BC557BC558BC559BC560BC635BC636BC637BC638BC639BC640BCY70BCY71BCY78BCY79BCY87BCY88BCY89MPSL01 MPSL51 MPSA06 MPSA42 MPSA43 MPSA56 MPSA92 MPSA93中、大功率管2N6283 2N6284 2N6286 2N6287 BD135 BD136 BD137 BD138 BD139 BD140 BD162 BD203 BD204 BD241C BD242C BD243 BD249 BD250 BD375 BD376 BD377 BD378 BD379 BD380 BD543 BD529 BD530 BD533 BD534 BD535 BD536 BD537 BD538 BD677 BD678 BD679 BD680 BD681 BD682 BD591 BD592 BDX53C BDX54C BDW51 BU208A BU508AMJ2955MJ4502MJ15003MJ15004MJE340MJE350MJE15028MJE15029MJE15030MJE15031PMD16K100PMD17K100TIP31TIP32TIP122TIP140TIP141TIP142TIP145TIP146TIP147TIP2955TIP3055Fet 晶体管2N52482N54572N5460BS170BF245CBF256BJ210J211J212Fet 功率管2SK15302SJ201IRF540IRF9540集成电路（模拟）AD711CA3130LH0032LF351LF411LM108LM208LM833LM358LM359LM324LM391LM393NE5532NE5534OP27OP37TL071TL072TL074TL081TL082TL084TLC271TLC272TLC274MN3004IC's 功率放大 [模拟] L165LM388LM1875TDA1516BQTDA1519CTDA1563QTDA2002TDA2005TDA2004TDA2030STK4036 IISTK4036 XISTK4038 IISTK4040 IISTK4040 XISTK4042 IISTK4042 XISTK4044 IISTK4044 IISTK4046 XISTK4048 XISTK4050 V显示驱动LM3914LM3915UAA180CA3161ECA3162EICL7136PLL 立体声解码LM1800CA3090PMC1310P定时-时钟电路555556MN3101XR2206光电耦合4N254N264N274N284N354N364N37H11A1H11A2H11A3SCR - TRIAC BTY79-800RC106D时钟MM5314N二极管1N4000 系列1N41481N5408IN5236B1N5240B1N5252B电子管300B5U4G6SN76BX76DJ8ECC886N1PECC88692212AT712AU712AX7E80CCECC81ECC82ECC83ECC88EL34EL84Z2CKT88常用锁相环电路集成电路型号(规格) 数据表生产厂家器件名称参考单价兼容型号EM92600/1EMC 专用型锁相环（中国10频道）HT9286A/BHT9287A/BHOLTEK 专用型锁相环（美国10频道）HT9288A/BHOLTEK 专用型锁相环（中国10频道）HYL21011S/JHYUNDAI 通用型锁相环HYL21012S/JHYUNDAI 专用型锁相环（美国10频道）HYL21014S/JHYUNDAI 专用型锁相环（中国10频道）MC145162MOTOROLA通用型锁相环MC145166MOTOROLA专用型锁相环（美国10频道）MC145167MOTOROLA专用型锁相环（美国10频道）KS8805BGM6532LG 专用型锁相环（中国10频道）DMD5603DAEWOO专用型锁相环（中国10频道）DMD5602DAEWOO专用型锁相环（美国10频道）KA567KA567LLM567常用元器件ICL7106,ICL7107DAC0830/DAC0832ADC0831/ADC0832/ADC0834/ADC0838 ADC0808/ADC0809ADC0802/ADC0803/ADC0804AD7520/AD7521/AD7530/AD75214N35/4N36/4N37ICL7116,ICL7117ICL7650ICL7660/MAX1044ICL7106,ICL7107DAC0830/DAC0832ADC0831/ADC0832/ADC0834/ADC0838 ADC0808/ADC0809ADC0802/ADC0803/ADC0804AD7520/AD7521/AD7530/AD75214N35/4N36/4N37ICL7116,ICL7117ICL7650ICL7660/MAX1044ICL8038ICM7216ICM7226ISO2-CMOSLF351LF353LM117/LM317A/LM317LM124/LM124/LM324LM137/LM337LM139/LM239/LM339LM158/LM258/LM358LM193/LM293/LM393LM201/LM301LM231/LM331LM285/LM385LM308ALM386LM399LM431LM567/LM567CLM741LM831LM833LM8365MAX038MC1403MC1404MC1413/MC1416MC145026/MC145027/MC145028MC145403-5/8MC145406MC145407MC145583MC145740MC1488MC1489MC2833MC3362MC4558MC7800系列MC78L00系列MC78M00系列MC78T00系列MC7900系列MC79L00系列MC79M00系列Microchip PIC系列单片机RS232通讯应用MM5369MOC3009/MOC3012MOC3020/MOC3023MOC3081/MOC3082/MOC3083MOC8050MOC8111MT8870MT8888CNE5532/NE5532ANE5534/SE5534NE555/SA555NE556/SA556/SE556NE570/NE571/SA571OP07OP27OP37OP77OP90PC817/PC827/PC847PT2262PT2272SG2524/SG3524ST7537TDA1521TDA7000TTDA7010TTDA7021TTDA7040TTDA7050TL062/TL064TL071/TL072/TL074TL082/TL084 JFETTL494TL594TLP521/1-4TOP100-4TOP221-7TOP232-4TOP412/TOP414ULN2068ULN2803ULN2803/ULN2804VFC32LM319LM393/LM339经典8腿IC封装（LM393）经典14腿IC封装（LM339）电源范围 2――36V静态工作电流 0.4mA翻转时间 1.3us最大输出电流 16mA输入电压范围 －0.3V――Vcc型号功能简述功能16位 20us高性能模数转换器(民用级)16位 20us高性能模数转换器(民用级)12位 1.25MHz采样速率带宽2MHz模数转换器(民用级)12位 3MHz采样速率带宽20MHz单电源模数转换器(工业级)12位 100KHz采样速率带宽500KHz模数转换器(工业级)12位 100KHz采样速率带宽500KHz模数转换器(民用级)小型2KHz隔离放大器(民用级)卧式小型2KHz隔离放大器(民用级)立式小型5KHz隔离放大器(民用级)卧式带信号调理比率输出型温度传感器可编程温控开关电阻可编程温度控制器 SOIC数字隔离放大器可编程正弦波振荡器（工业级） PLCC16位单电源 4-20mA输出数模转换器（工业级）DIP16位单电源 4-20mA输出数模转换器（工业级）SOIC16位环路供电符合HART协议 4-20mA输出数模转换器（工业级）DIP 16位环路供电符合HART协议 4-20mA输出数模转换器（工业级）SOIC 低价格，低偏置电流，高输入阻抗运放(民用级) TO-99低价格，低偏置电流，高输入阻抗运放(民用级) TO-99低失调电压，高性能运放 (民用级) TO-99宽带，低价格运放(民用级) TO-99电阻设置增益精密仪表放大器（民用级）DIP引脚设置增益高精度仪表放大器（工业级）DIP软件编程仪表放大器（工业级）DIP软件编程仪表放大器（民用级）DIP模拟乘法器(民用级)TO-99模拟乘法器(民用级)DIP模拟乘法器(民用级)TO-99集成真有效值直流转换器(民用级)DIP集成真有效值直流转换器(民用级)TO-99集成真有效值直流转换器(民用级)DIP150KHZ集成压频转换器（民用级）TO-99150KHZ集成压频转换器（军用级）TO-99单片实时模拟乘法器（工业级）DIP宽带双通道线性乘法器（民用级）DIP低价格，低偏置电流，高输入阻抗运放(民用级) TO-99低偏置电流，高输入阻抗运放(民用级) TO-99静电计放大器（民用级）DIP低价格，低偏置电流，高输入阻抗运放(民用级) TO-99精密 BiFET输入运放（民用级）DIP低偏置电流，高输入阻抗运放(民用级) TO-99低偏置电流，高输入阻抗运放(民用级) TO-99高速运放（民用级）DIP微处理器兼容完整7位电压输出数模转换器（民用）DIP微处理器兼容完整8位电压输出数模转换器（民用）DIP12位 0.25us电流输出数模转换器（民用）DIP12位超高速电流输出数模转换器（民用）DIP16位 3us电流输出数模转换器（民用）DIP8位 25us模数转换器（民用）DIP12位 25us模数转换器（民用）DIP12位 25us模数转换器（民用）DIP12位 3us模数转换器（民用）DIP精密 2.5V电压基准源（民用级）TO-52精密 2.5V电压基准源（民用级）TO-52精密 10V电压基准源（民用级）TO-50.7us采样保持放大器（民用）DIP引脚设置输出电压基准源（民用级）TO-99引脚设置输出电压基准源（民用级）DIP3us采样保持放大器（工业级）DIP精密 5V电压基准源（民用级）DIP精密 5V电压基准源（民用级）DIP精密 5V电压基准源（民用级）DIP精密 5V电压基准源（民用级）DIP精密 5V电压基准源（民用级）SOIC精密 10V电压基准源（民用级）DIP精密 10V电压基准源（民用级）SOIC精密可编程电压基准源（工业级）DIP精密 1.235V电压基准源（民用级）H-02A—55℃～150℃测温范围温度传感器 TO-52—55℃～150℃测温范围温度传感器 TO-52低价格，精密单片温度传感器 TO-92低价格，精密单片温度传感器 TO-92K型（铬-铝）热电偶信号调节器（工业级）DIPK型（铬-铝）热电偶信号调节器（工业级）DIP线性可变位移信号调节器（LVDT）（工业级）DIP低噪声宽带可变增益双运放（民用级）DIP低噪声宽带可变增益双运放（民用级）DIP低噪声可变增益运放（工业级）DIP50MHz, 80db对数放大器（民用级）DIP低功耗混频器/AGC/RSSC 3V接收机的IF子系统（工业级） SSOP 低功耗仪表放大器（工业级）DIP低功耗仪表放大器（工业级）DIP单电源仪表放大器（工业级）DIP单电源Rail-Rail输出仪表放大器（工业级）DIP单电源Rail-Rail输出仪表放大器（工业级）SOIC精密仪表放大器（工业级）DIP可编程增益仪表放大器（民用级）DIP可编程增益仪表放大器（民用级）DIP单电源仪表放大器（工业级）DIP单电源低功耗Rail-Rail输出仪表放大器（工业级）DIP高电压抑制比差分放大器（工业级） DIP平衡跳制解调器（民用级）DIP低价格模拟乘法器（民用级）DIP高精度真有效值直流转换器（民用级）DIP高精度真有效值直流转换器（民用级）TO-99高精度真有效值直流转换器（民用级）DIP精密，BiFET输入运放（民用级）DIP1MHz，电压频率转换器（民用级）DIP1MHz，电压频率转换器（民用级）DIP2MHz，同步电压频率转换器（工业级）DIP500KHz，低价格电压频率转换器（民用级）DIP500KHz，低价格电压频率转换器（民用级）SOIC16位 8us串并行输入数模转换器（工业级）DIP12位65MSPS模数转换器(工业级) LQFP14位65MSPS模数转换器(工业级) LQFP12位 3us并行输入数模转换器（民用级）DIP12位 3us并行输入数模转换器（民用级）DIP16位 8us并行输入数模转换器（工业级）DIP单电源，内带仪表放大器电压基准源8位数模转换器（民用级）DIP16位100KSPS采样速率并行输出模数转换器（民用级）DIP16位100KSPS采样速率并行输出模数转换器（民用级）DIP16位100KSPS采样速率并行输出模数转换器（民用级）DIP16位100KSPS采样速率串行输出模数转换器（民用级）SOIC16位100KSPS采样速率串行输出模数转换器（民用级）DIP16位100KSPS采样速率串行输出模数转换器（民用级）DIP12位200KSPS采样速率并行输出模数转换器（民用级）DIP12位200KSPS采样速率并行输出模数转换器（民用级）DIP14位128KSPS采样速率并行输出模数转换器（民用级）DIP14位128KSPS采样速率并行输出模数转换器（民用级）DIP精密 2.5V电压基准源（民用级）DIP1us 四通道采样保持放大器（民用级）DIP环路供电，4～20mA输出传感器信号变送器（工业级）DIP0～2V或0～10V输入，4～20mA或0-20mA输出信号变送器（工业级）DIP 0～2V或0～10V输入，4～20mA或0-20mA输出信号变送器（民用级）DIP 通用线性可变位移信号调节器（LVDT）（工业级）PLCC带10位D/A，20MHz主频直接数字同步调制器（工业级）PLCC带10位D/A，50MHz主频直接数字同步调制器（民用级）PLCC精密四运放（民用级）DIP精密运放（民用级） DIP精密双运放（民用级） DIP精密单运放（工业级）DIP精密单运放（民用级）DIP双AD707（工业级）DIP双AD707（民用级）DIP0.37db对数数模转换器（工业级）DIP0.37db对数数模转换器（工业级）DIP精密 BiFET输入运放（工业级）DIP精密 BiFET输入运放（民用级）DIP精密 BiFET输入运放（民用级）SOIC双AD711（工业级）DIP双AD711（民用级）DIP四AD711（工业级）DIP四AD711（民用级）DIPRGB-NTSC/PAL编码器（民用级）PLCC8位 3us转换时间电压输出数模转换器（民用级）DIP8位 4通道3us转换时间电压输出数模转换器（民用级）DIP8位 8通道5us转换时间电压输出数模转换器（工业级）DIPAnalog toNTSC/PAL编码器（民用级） SOIC12位 2通道5us转换时间电压输出数模转换器（工业级）DIP12位 2通道5us转换时间电压输出数模转换器（民用级）DIP12位电压输出型数模转换器（工业级） DIP12位 10us转换时间电压输出数模转换器（工业级）DIP12位双路串行输出数模转换器（工业级） DIPAnalog toNTSC/PAL编码器（民用级） SOIC16位6通道数据采集子系统（三相电量测量IC）（工业级） SOIC10MHz带宽四象限模拟乘法器（工业级）DIP通用真有效值直流转换器（民用级）DIP通用真有效值直流转换器（工业级）DIP通用真有效值直流转换器（民用级）DIP片内带D/A 数字输出温度传感器 LM35升级品可8片级联（工业级）SOIC 通用运放（民用级）DIP低噪声，BiFET输入运放（民用级）DIP精密，双极性运放（民用级）DIP精密低噪声运放（民用级） DIP16×16音频距阵开关（民用级） PLCC8选1 CMOS多路转换器（民用级）DIP差动4选1 CMOS多路转换器（民用级）DIP差动4选1 CMOS多路转换器（民用级）DIP8选1 CMOS多路转换器（民用级）DIP16选1 CMOS多路转换器（民用级）DIP差动8选1 CMOS多路转换器（民用级）DIP四单刀单掷 CMOS介质隔离模拟开关9民用级）DIP四单刀单掷 CMOS介质隔离模拟开关9民用级）DIP双单刀双掷 CMOS介质隔离模拟开关9民用级）DIP双单刀双掷 CMOS介质隔离模拟开关9民用级）DIP10位 CMOS数模转换器（民用级）DIP8位 CMOS数模转换器（民用级）DIP8位 CMOS带锁存数模转换器（民用级）DIP8位 180ns电流输出CMOS数模转换器（民用级）DIP8位 180ns电流输出CMOS数模转换器（民用级）DIP10位 600ns电流输出CMOS数模转换器（民用级）DIP14位 1.5us电流输出CMOS数模转换器（民用级）DIP12位双路1.5us电流输出CMOS数模转换器（民用级）DIP12位 600ns电流输出CMOS数模转换器（民用级）DIP12位 250ns电流输出CMOS数模转换器（民用级）DIP12位串行输入CMOS数模转换器（民用级）DIP12位 1us电流输出CMOS数模转换器（民用级）DIP低功耗四路数模转换器（工业级） DIP8位 15us电流输出CMOS数模转换器（民用级）DIP四单刀单掷 CMOS带锁存介质隔离模拟开关9民用级）DIP16位100KSPS CMOS模数转换器（工业级） LQFP16位570KSPS CMOS模数转换器（工业级） LQFP12位高速电压输出数模转换器（民用级）DIP16位高速电流输出数模转换器（民用级）SOIC16位 ∑–△模数转换器（工业级）DIP20位 ∑–△模数转换器（工业级）DIP20位 ∑–△模数转换器（工业级）DIP16位 ∑–△模数转换器（工业级）DIP16位 ∑–△模数转换器（工业级）SOIC16位 ∑–△模数转换器（工业级）DIP16位 ∑–△模数转换器（工业级）SOIC24位 ∑–△模数转换器（工业级）DIP24位 ∑–△模数转换器（工业级）DIP24位 ∑–△模数转换器（工业级）DIP24位 ∑–△模数转换器（工业级）DIP24位 ∑–△模数转换器（工业级）DIP 3V电源24位 ∑–△模数转换器（工业级）DIP 5V电源16位 ∑–△模数转换器（工业级）DIP 5V电源16位 ∑–△模数转换器（工业级）SOIC 5V电源24位 ∑–△模数转换器（工业级）DIP单通道输入6MHz压频转换器（工业级） DIP四通道输入6MHz压频转换器（工业级） DIP两通道乘积/频率转换器电度表专用芯片（工业级）DIPIEC521/1036标准电度表专用芯片（工业级）DIP10位多路T/H子系统（工业级） SOIC14位128KSPS采样速率并行输出模数转换器（民用级）DIP2.5V或3V可选输出高精度电压基准源（工业级）DIP700ns采样保持放大器（民用级）DIP8位500KSPS采样速率模数转换器（民用级）DIP8位1MSPS采样速率模数转换器（民用级）DIP8位2MSPS采样速率模数转换器（工业级）DIP8位四通道高速模数转换器（民用级）DIP8位四通道高速模数转换器（工业级）DIP12位双路乘法数模转换器（工业级）DIP12位乘法数模转换器（民用级）DIP16位电压输出数模转换器（民用级）DIP12位双路乘法数模转换器（工业级）DIP14位8通道285KSPS采样速率模数转换器（工业级）DIP12位4通道同时采样250KSPS速率模数转换器带2SHA and 2ADCs（工业级）DIP 12位4通道同时采样147KSPS速率模数转换器（工业级）PQFP14位4通道同时采样175KSPS速率模数转换器带2SHA and 2ADCs（工业级）PQFP 14位串行输出模数转换器（工业级）DIP12位 750KSPS采样速率模数转换器（民用级）DIP12位8通道200KSPS速率模数转换器（工业级）SOIC12位单电源八通道串行采样模数转换器（工业级）DIP12位单电源八通道串并行采样模数转换器（工业级）DIP12位600KSPS采样模数转换器（工业级）DIP12位单电源200KSPS采样速率模数转换器（工业级）DIP12位四通道同时采样模数转换器（工业级）DIP12位四通道同时采样模数转换器（工业级）SOIC12位 750KSPS采样速率模数转换器（民用级）DIP高速精密比较器（民用级）DIP低偏置电流低噪声运放（民用级）DIP低失真低噪声运放（工业级）DIP低失真低噪声运放（工业级）SOIC800MHz 电流反馈运放（工业级）DIP800MHz 电流反馈双运放（工业级）DIP1GHz 4500V/us 电流反馈双运放（工业级）DIP340MHz 电流反馈运放（工业级）DIP单电源真空管前置放大器（工业级） SOIC5V Rail-Rail 大电流输出 XDSL线性驱动放大器（工业级） SOIC 单电源 Rail-Rail输入输出运放（工业级）DIP单电源 Rail-Rail输入输出双运放（工业级）DIP低失真宽带240MHz电压输出运放（工业级）DIP低失真宽带270MHz电压输出运放（工业级）DIP120MHz带宽 Rail-Rail输出运放(工业级)DIP120MHz带宽 Rail-Rail输出运放(工业级)SOIC120MHz带宽 Rail-Rail输出双运放(工业级)DIP80MHz带宽 Rail-Rail输出四运放(工业级)DIP电压反馈运放（工业级） DIP电压反馈运放（工业级） SOIC低价格 300MHz电压反馈双运放(工业级) SOIC电压反馈双运放（工业级） SOIC双通道 260MHz缓冲器(工业级) SOIC8×8视频距阵开关（工业级） LQFP8×8视频距阵开关（工业级） LQFP带电源休眠控制端的低功耗视频运放(工业级) DIP16×8视频距阵开关（工业级） LQFP16×16视频距阵开关（工业级） LQFP16×16视频距阵开关（工业级） LQFP高性能视频运放(工业级) DIP高性能视频运放(工业级) SOIC低功耗电流反馈双运放(工业级) DIP低功耗电流反馈双运放(工业级) SOIC差分输入输出电压反馈放大器（工业级） SOICIF 放大器（工业级） SOIC单电源低功耗三视频运放(工业级) DIP单电源低功耗三视频运放(工业级) SOIC大电流输出,差动输入\输出运放(工业级)2选1视频多路转换器(工业级) DIP4选1视频多路转换器(工业级) DIP高速低功耗宽电源运放(工业级) DIP差动2选1视频多路转换器(工业级) DIP4选1视频多路转换器(工业级) DIP低价格高速电压反馈视频运放(工业级) DIP单电源低功耗FET输入 Rail-Rail输出运放(工业级) DIP 双AD820(工业级) DIP双AD820(工业级) DIP 3V电源单电源 Rail-Rail输出双运放（工业级） DIP单电源 Rail-Rail输出四运放（工业级） DIP高速低功耗双运放(工业级) DIP双AD847 (工业级) DIP双AD847 (民用级) DIP双AD818(工业级) DIP高速低噪声视频运放(工业级) DIP500MHz对数放大器（工业级）DIP500MHz对数放大器（工业级）SOIC500MHz对数放大器（工业级）TSSOP高速视频差动运放(工业级) DIP高速视频差动运放(工业级) DIP2.5GHz对数放大器（工业级） RM-82.5GHz对数放大器（工业级） RM-8数字可变增益线性驱动器（工业级） RP-20500MHz带宽四象限模拟乘法器（工业级）DIP差分输入射频放大器（工业级） SOIC250MHz带宽四象限电压输出模拟乘法器（工业级）DIP2通道数字电位器阻值10K(工业级) DIP4通道数字电位器阻值100K(工业级) DIP宽带高速运放(民用级) DIP34MHz带宽高速FET输入运放(工业级) DIP2000V/us高速运放(工业级) DIP16MHz带宽高速FET输入运放(民用级) DIP16MHz带宽高速FET输入运放(民用级) DIP300V/us高速低功耗运放(工业级) DIP300V/us高速低功耗运放(民用级) DIP300V/us高速低功耗运放(军用级) DIP高速低功耗运放(民用级) DIP12 位单电源双路电流输出型数模转换器（工业级） DIP 自稳零运放（工业级） SOIC自稳零双运放（工业级） SOIC单电源比较器（工业级）DIP单电源比较器（工业级） SOIC单电源TTL/CMOS四路比较器（工业级） DIP单电源双路比较器（工业级） DIP12位41MSPS模数转换器(工业级) LQFP8位35MSPS视频模数转换器(民用级) DIP9位30MSPS模数转换器(工业级) SSOP10位40MSPS模数转换器(工业级) SOIC10位60MSPS模数转换器(工业级) SSOP8位40MSPSz视频模数转换器(工业级) SSOP8位60MSPS视频模数转换器(工业级) SSOP双路8位50MSPS视频模数转换器(民用级) LCC双路8位60MSPS视频模数转换器(工业级) SSOP双路6位60MSPS视频模数转换器(民用级) SSOP10位TTL兼容100MSPS模数转换器(工业级) SOIC7ns建立时间采样保持放大器（工业级） SOIC10位20MSPS模数转换器(工业级) SSOP10位40MSPS模数转换器(工业级) TSSOP12位10MSPS模数转换器(工业级) SOIC12位1MSPS模数转换器(工业级) SOIC12位3MSPS模数转换器(工业级) SOIC12位25MSPS模数转换器(工业级) SOIC12位65MSPS模数转换器(工业级) SSOP14位10MSPS模数转换器(工业级) MQFP14位3MSPS模数转换器(工业级) MQFP16位2.5MSPS∑–△模数转换器（工业级）MQFP单电源8位32MSPS模数转换器（工业级） SSOP单电源 8位双路32MSPS模数转换器（工业级） SSOP单电源8位100MSPS模数转换器（工业级） SSOP单电源8位80MSPS模数转换器（工业级） SSOP单电源 8位双路80MSPS模数转换器（工业级） SSOP4选1宽带视频多路转换器(民用级) DIP8位 100MSPS三视频模数转换器（民用级）MQFP数字化可编程延迟信号发生器(工业级) DIPTTL/COMS数字化可编程延迟信号发生器(民用级) DIP 1400V/us,140MHz带宽高速运放(民用级) SOIC1400V/us,140MHz带宽高速运放(民用级) DIP1800V/us,160MHz带宽高速运放(民用级) DIP低失真闭环缓冲放大器(工业级) DIP超低失真宽带电压反馈放大器(工业级) DIP高速双电压比较器(工业级) DIP高速TTL兼容双电压比较器(工业级) DIP8位100MSPS 双路数模转换器（工业级） TSSOP8位125MSPS 双路数模转换器（工业级） PQFP12位 80MSPS TTL兼容数模转换器(工业级) DIP10位 400MSPS TTL兼容数模转换器(工业级) SOIC10位 170MSPS 双电源数模转换器(工业级) SOIC10位 200MSPS 单电源数模转换器(工业级) SSOP10位125MSPS 数模转换器（工业级） SOIC12位125MSPS 数模转换器（工业级） SOIC10位100MSPS 数模转换器（工业级） SOIC12位100MSPS 数模转换器（工业级） SOIC14位100MSPS 数模转换器（工业级） SOIC16位100KSPS BiCMOS并行输出模数转换器（工业级） DIP16位100KSPS BiCMOS并行输出模数转换器（工业级） DIP16位200KSPS BiCMOS并行输出模数转换器（工业级） DIP14位300MSPS 数模转换器（工业级） LQFP16位200KSPS BiCMOS串行输出数模转换器（工业级） DIP16位100KSPS BiCMOS串行输出数模转换器（工业级） DIP10位 6MSPS CCD信号处理器（民用级）LQFP10位 6MSPS CCD信号处理器（民用级）LQFP10位 6MSPS CCD信号处理器（民用级）LQFP10位 3通道 6MSPS CCD信号处理器（民用级） MQFP12位 3通道 6MSPS CCD信号处理器（民用级） MQFP14位 3通道 12MSPS CCD信号处理器（民用级） SOIC带10位D/A，25MHz主频直接数字同步调制器（工业级）PQFP带10位D/A，50MHz主频直接数字同步调制器（工业级）PQFP带10位D/A，25MHz主频直接数字同步调制器（工业级）TSSOP带10位D/A，125MHz主频直接数字同步调制器（工业级）SSOP带10位D/A，180MHz主频直接数字同步调制器（工业级）SSOP带12位D/A，200MHz主频直接数字同步调制器（工业级）LQFP-80带散热器带12位D/A，300MHz主频直接数字同步调制器（工业级）LQFP-80数字 QPSK/16 QAM 调整器（工业级） PQFP带12位D/A，200MHz主频直接数字同步调制器（工业级）LQFP-80带散热器带12位D/A，300MHz主频直接数字同步调制器（工业级）LQFP-80线性相位探测器/频率鉴别器（民用级） DIP四单刀单掷模拟开关（民用级） DIP四单刀单掷模拟开关（民用级） DIP四单刀单掷模拟开关（民用级） DIP四单刀单掷模拟开关（民用级） DIP四单刀单掷模拟开关（工业级） DIP四单刀单掷模拟开关（工业级） SOIC8选1CMOS模拟多路转换器（工业级） DIP差动4选1CMOS模拟多路转换器（工业级） DIP四单刀单掷模拟开关（工业级） DIP单刀单掷模拟开关（工业级） DIP单刀单掷模拟开关（工业级） DIP四单刀单掷模拟开关（工业级） DIP双单刀单掷模拟开关（工业级） DIP四单刀单掷模拟开关（工业级） DIP四单刀单掷模拟开关（工业级） DIP16选1CMOS模拟多路转换器（民用级） DIP差动8选1CMOS模拟多路转换器（民用级） DIP8选1CMOS模拟多路转换器（民用级） DIP8选1CMOS带过压保护模拟多路转换器（工业级） DIP差动4选1CMOS模拟多路转换器（民用级） DIP单电源四单刀单掷模拟开关（工业级） DIP8选1CMOS模拟多路转换器（工业级） DIP差动4选1CMOS模拟多路转换器（工业级） DIP单路视频CMOS模拟开关（工业级）RM-6双路视频CMOS模拟开关（工业级）RM-10DC-DC转换器（工业级）DIP微处理器监控电路（工业级） DIP微处理器监控电路（工业级） DIP32位浮点数字信号处理器内存4M（民用级）PQFP32位浮点数字信号处理器内存4M（工业级）PQFP32位浮点数字信号处理器内存2M（民用级）PQFP16位定点数字信号处理器（民用级）PQFP-12816位定点数字信号处理器（民用级）TQFP-128带单片机、8路12位A/D、2路D/A的数采系统（工业级）PQFP 500KHz工业标准压频转换器（民用级） DIP±1g-±5g带温度补偿加速度传感器（民用级）QC-14±2g双路加速度传感器（工业级）QC-14高精度仪表放大器（工业级） DIP单电源精密仪表放大器（工业级） DIP8位高速电流输出型数模转换器（民用级） DIP8位双路电压输出型数模转换器（工业级） DIP超低失调电压运放（军用级）DIP超低失调电压运放（工业级）DIP超低失调电压运放（工业级）SOIC低失真低噪声运放（工业级）DIP高精密运放（工业级） DIP低噪声精密运放（工业级） DIP单电源 Rail-Rail输入输出双运放（工业级）DIP单电源 Rail-Rail输入输出双运放（工业级）DIP微功耗 Rail-Rail输入输出双运放（工业级）DIP超低偏置电流精密双运放（工业级） DIP超低偏置电流精密双运放（工业级） SOIC低噪声精密运放（民用级） DIP低噪声精密运放（工业级） DIP单电源 Rail-Rail输入输出四运放（工业级）DIP超低偏置电流精密四运放（工业级） DIPOP07改进型（工业级） DIP低电压微功耗精密运放（工业级） DIP微功耗精密运放（工业级） DIP微功耗精密运放（工业级） SOIC峰值检测器（工业级） DIP精密5V电压基准源带温度传感器（工业级） DIP精密低价格2.5V电压基准源（工业级） DIP低功耗大电流输出2.5V电压基准源（工业级） DIP低功耗大电流输出2.5V电压基准源（工业级） SOIC低功耗大电流输出4.5V电压基准源（工业级） DIP低功耗大电流输出5V电压基准源（工业级） SOIC高精度2.5V电压基准源（工业级）DIP7us四通道采样保持放大器（工业级） DIP7us八通道采样保持放大器（工业级） DIP差动线路接收器 Gain=0dB(工业级） DIP平衡线路驱动器（工业级） DIP差动线路接收器 Gain=-6dB(工业级） DIP1W功率差分输出音频功率放大器（工业级）DIPRail-Rail输出双音频功率放大器（工业级）DIPPWM输出，直接与微处理器接口数字输出温度传感器 SOIC反相PWM输出，直接与微处理器接口数字输出温度传感器 SOIC 电压输出温度传感器 TO-92波形发生器60KHz振荡器自举模式DC-DC 电荷泵转换器低价格双路14位串形模数转换器低价格双路14位串形模数转换器低价格14位串形模数转换器高速带采保和基准的12位模数转换器微处理器监控电路10位带2.5V基准的串形模数转换器14位2×4通道4路同时采集并行模数转换器积分型A/D转换器，+5V，3-3/4位低功率A/D转换器积分型A/D转换器积分型A/D转换器完全隔离半双RS-485接口完全隔离半双RS-485接口RS-485/RS-442接口，256个节点RS-485/RS-442接口，128个节点RS-485/RS-442接口，+15KV保护RS-232接口，+15KV保护RS-232接口，+15KV保护低功耗8路10位A/D完全隔离全双IKS-485接口高速8路8位A/D开关型DC-DC变换器开关型DC-DC变换器8路12位A/D串行接口A/D，带采保，电压基准，12位，采样速率133KHZ串行A/D，12位，采样速率75KHZ低功耗，12位单通道，串行带采保和电压基准A/D低功耗，12位单通道，带采保和电压基准A/D串行A/D，10位采样速率133M12位，八通道故障保护，带采保并行A/DRS-232接口,+5VRS-232接口＋15KV静电保护RS-232接口＋15KV静电保护，工业级RS-232接口工业级RS-232接口RS-232接口RS-232接口RS-232接口,+5VRS-232接口工业级RS-232接口RS-232接口5组收发器RS-232接口RS-232接口双路，开关电容型4阶滤波器双路，开关电容型4阶滤波器双路，开关电容型4阶滤波器单路，开关电容型5阶滤波器有源滤波器，时钟可编程有源滤波器，时钟可编程有源滤波器，时钟可编程有源滤波器，时钟可编程有源滤波器，时钟可编程模拟开关模拟开关模拟多路转换器失效保护RS-485/RS-232失效保护RS-485/RS-232模拟多路转换器模拟多路转换器通用异步收发信机（UART）模拟开关模拟开关模拟开关模拟开关RS-232接口RS-232接口RS-232接口模拟开关模拟开关模拟多路转换器模拟多路转换器模拟开关模拟多路转换器模拟多路转换器模拟多路转换器（工业级）模拟多路转换器模拟多路转换器模拟多路转换器模拟多路转换器模拟多路转换器模拟多路转换器运算放大器视频放大器视频放大器视频放大器视频放大器。

SATEC PRO EM235 快速入门指南说明书

SATEC PRO EM235 快速入门指南说明书

This guide instructs the user on installation, wiring, configuring and operating the EM235 multi-meter. This guide does not substitute the full user manual or the detailed safety instructions. To download the manual and other related material, please visit our website: .Warning! Only a licensed electrician may perform the installation and wiring of the EM235.Figure 1: EM235 front panelINSTALLATIONThe PRO EM235 is designed exclusively for installation on DIN-rail.Please note to leave room for future expansion : when installing a basic unit (without modules), it is recommended to maintain a minimal gap of 30-100mm to the right of the unit, allowing future installation of additional detachable SATEC modules (figure 5; depending on number of added modules, 17.8mm each).Figure 2: Opening the latchThe following steps (Figure 3) correspond with a low-voltage three phase network:1.Make sure all power sources are disconnected.2.Make sure that your designated power supply corresponds with the unit's rating.3.Connect the power supply (bottom-left of front panel) via 12 AWG wires and adesignated circuit breaker.4.Standard external current transformers: connect the CT's (14 AWG minimum) "+" pole tothe device's I1+ current input (unit’s bottom right of front panel, as in figure 3) and the "-" pole to the adjacent I1- current input. Repeat this for the following two phases, I2 and I3. Verify proper polarity in your connections in accordance with the arrow printed on the external CTs.“HACS” CTs: connect the red/white wire to the "+" terminal and the black/orange (colors vary according to the CT model) wire to the "-" terminal.5.Connect the voltage measurement inputs (22-12 AWG; bottom-center of front panel).6.Connect the com wire (26-12 AWG, shielded) to COM1 (RS485, top-left of front panel).7.Power-on the unit.Figure 3: Typical wye installationThe PRO EM235is operated via the LCD display, 2 LEDs and 4 pushbuttons (figure 1: front panel).When powered on, the device will default to displaying voltages, for basic setup back up (<- button) to the home screen navigate with arrows to “setup” (select with ), enter default password (“9”) and select (“apply”). Open “general setup” to reveal “basic setup” for configuration. See screenshot sequence in figure 4, below.Figure 4: Screenshot sequence for basic setup1.DO NOT HOT-SWAP. When adding/removing modules, make sure the unit isdisconnected from power supply2.Remove cover (sticker on right side of unit) to reveal port3.Attach the module tightly and tighten the clips4.Power on the unitFigure 5: module expansion, front panel view1.Default password: 92.Default IP: 192.168.0.203 (ETH1)3.Default current mode (HACS model): Alternating Current (AC)4.Default serial com settings (RS485): 19,200 Baud rate; address = 15.For convenient configuration please use SATEC’s PAS engineering software, connectingyour PC to the USB port (type C) at the right side of the front panel)To download PAS (free): /power-analysis-softwaremake sure to update .exe file with the most recent update available on webpageCopyright © 2021 SATEC Ltd.。

Maxum 参数中文版

Maxum 参数中文版
Kulicke & Soffa
K&S Maxµm plus 参数手册
MAXµm
基本制程参数指导
客户版
库力索法股份有限公司 台湾教育训练
1
薛健熙 编译 / 苏钊弘 修订
9-28-2-32b
Kulicke & Soffa
注意:
K&S Maxµm plus 参数手册
适当的 DOE 专业知识及了解可以提供这份说 明中所列举出的全部参数的实际定义，以及参 数之间的相互作用。
13. USG PROFILE (Square, Ramp or Burst) 这一个参数在控制针对特别的焊黏点其超音波输出的特征，共有三种超音波输出波型：方波
(Square)、升降波(Ramp)以及凸波(Burst)，请参考在 Figure 4 所显示一般的组合波型。
Z Position
USG Pre-Delay
12. USG PRE-BLEED (%) (Min 0, Max 100, Default 0) 当此参数被设定时，USG Pre-bleeding 在 Tip1 的高度时被启动作用直到第一焊点接触讯号被送出，
此一参数的设定可被考虑为额外的能量输出。注意：当 USG pre-delay 是设定为 On 时，pre-bleed 的输出能量将会被启动(On)一直到 pre-delay 的作用时间结束，参考 Figure 3。
库力索法股份有限公司 台湾教育训练
3
薛健熙 编译 / 苏钊弘 修订
9-28-2-32b
Kulicke & Soffa
建议的设定值是： TIP 1 = 5 mils (125µm) TIP 2 = 5 mils (125µm)

MAX352中文资料

MAX352中文资料
Note 2: All leads are soldered or welded to PC board.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Digital Inputs, VCOM, VNC, VNO (Note 1) ...........(V- - 2V) to (V+ + 2V) .........................................................or 30mA (whichever occurs first) Current (any terminal) .........................................................30mA Peak Current COM_, NO_, NC_
Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10sec) .............................+300°C

常用磁芯产品手册参考

常用磁芯产品手册参考

NCD Ferrite Core 目录 Contents材料特性 Material Characteristics2-6 EE磁芯7-10 EE Cores平面E11-12型磁芯 Planar E CoresSE型磁芯 SE Cores13 EI型磁芯 EI Cores14-16 EER,ETD及EC型磁芯 EER,ETD&EC Cores17-18平面ER型磁芯 Planar ER Cores19 UU型磁芯 UU Cores20-21 UF型磁芯 UF Cores22 UR型磁芯 UR Cores23 UI型磁芯 UI Cores24-25 EFD型磁芯 EFD Cores26 EPC型磁芯 EPC Cores27 EP型磁芯 EP Cores28P型磁芯 P Cores29-30 PQ型磁芯 PQ Cores31 RM型磁芯 RM Cores32 PM型磁芯 PM Cores33 LM型磁芯 LM Cores34 ET及FT型磁芯 ET&FT Cores35环型磁芯 Ring Cores36-39 DT型磁芯 DT Cores40S型磁芯 S Cores41R型磁芯 R Cores42方块型磁芯 FK Cores43NCD Ferrite Core 材料特性 MATERIAL CHARACTERISTICS●功率铁氧体材料 Power ferrite materials特性符号单位LP1LP2LP3LP3A Characteristics Symbol Unit初始磁导率 Initial permeabilityμi-3000±25%2500±25%2300±25%2200±25%相对损耗因数 Relative loss factor tanδ/μi×10＜10-6＜5＜4＜3饱和磁通密度BsmT 25℃500500490Saturation flux density1194A/m100℃390390380剩磁 Remanence Br mT130130110矫顽力 Coercivity Hc A/m131310功率损耗Pc kW/m325℃Power loss80℃1209060 (f=25kHz,B=200mT)100℃1601007050功率损耗Pc kW/m325℃700650600Power loss80℃550480400(f=100kHz,B=200mT)100℃600450350居里温度 Curie temperature Tc℃≥220≥200≥200≥200密度 Density d kg/m33 4.8×10 4.8 4.8 4.8●高磁导率铁氧体材料 High permeability ferrite materials特性符号单位HP1HP2HP3HP3A Characteristics Symbol Unit初始磁导率 Initial permeabilityμi-5000±25%7000±25%10000±30%12000±30%相对损耗因数tanδ/μi×10-6＜15＜7＜7＜10Relative loss factor(100kHz)(10kHz)(10kHz)(10kHz)饱和磁通密度Bs mT 420400400380Saturation flux density1194A/m1194A/m1194A/m1194A/m 剩磁 Remanence Br mT11010090110矫顽力 Coercivity Hc A/m1065 4.5减落因数 Disaccommodation factor DF×10＜3-6＜3＜2＜2居里温度 Curie temperature Tc℃≥140≥130≥120≥100密度 Density d kg/m33 4.85×10 4.9 4.95 4.95注：如无说明，各项数值均在室温下用Φ25×Φ15×10环型磁芯测得。

光伏并网逆变器SG100CX_136TX 用户手册说明书

光伏并网逆变器SG100CX_136TX 用户手册说明书

II
目录
版权所有 .....................................................................................................................I 关于本手册 ................................................................................................................. II
2 产品描述 ........................................................................................................... 4
2.1 光伏并网系统 ................................................................................................ 4 2.2 产品介绍....................................................................................................... 5
I
关于本手册
本手册主要介绍了逆变器的产品信息、安装、操作及维护说明，不包含光伏系统的全部信 息，可登录或设备制造商网站获取更多信息。 适用范围 本手册主要针对以下设备
• SG100CX • SG136TX
下文中除非特别指出，均简称为“逆变器”。
面向读者 本手册适用于需对逆变器进行安装、操作和维护的专业技术人员及对逆变器参数进行查看操 作的用户。

米勒焊机Maxstar说明书

米勒焊机Maxstar说明书

Miller Electric Mfg. Co. An Illinois Tool Works Company 1635 West Spencer Street Appleton, WI 54914 USAWeb Site International HeadquartersPhone: 920-735-4505USA FAX: 920-735-4134Canadian FAX: 920-735-4169International FAX: 920-735-4125Maxstar®200 Series TIG/Stick WeldingPower SourceIssued October 2003 • Index No. DC/32.0Auto-Line™provides state-of-the-art flexibility to the end user. TheAuto-Line circuitry automaticallyconnects to 120–460 VAC, single-or three-phase power withoutremoving the covers to relink thepower source. No longer is there aconcern if you have the correctmachine for shop or the job site.The Power of Blue®.Available in Three Models:SD—Provides the basic features that are required for most TIG or Stick welding applications.DX—When the job demands greater control the DX provides pulse on/off, pulse frequency, peak % time,background amperage, initial amperage,initial slope time, final slope time and final amperage control.LX—Automation made simple. With the Automation Interface Connector, the integrator can quicklyinterface to the output disable, weld start/stop, gas start/stop inputs; valid arc, pulse lock out, andend of weld sequence outputs.Portable in the shop or at the job site—at 37 lbthe Maxstar 200 is easily moved from locationto location.Superior TIG/Stick arc performance on all inputvoltages. Even on the difficult to run electrodeslike E6010.Inverter-based, DC power sourcehas state-of-the-art operatorinterface allowing the user extraset-up capabilities in a compactmachine. Features more precisecontrol of output parameters thantraditional knobs and switches.HF arc starting provides non-contact arc startingthat eliminates tungsten or material contamination.Lift-Arc™start provides TIG arc starting withoutthe use of high frequency.Programmable HF start parametersallows the independently setHF starting conditions based uponprocess or application.NEW!Low OCV Stick is a simpledesign that reduces the open-circuitvoltage to 13 volts when the weldingpower source is not in use. Thisbuilt-in circuit design eliminates theneed for add-on voltage reducers.Maxstar 200 DX Maxstar 200 LX Maxstar 200 SDPower source is warranted for 3 years, parts and labor.Original main power rectified parts are warranted for 5 years.2Control PanelCSA approval.Models with CE specifications are available and manufactured according to the Standards IEC-974-1 and EN-60974-1.*Indicates idle draw. **Sense voltage for Stick and Lift-Arc TIG.B.Initial Time (s)0.0–25 (LX only)C.Initial Amperage (A)1–200D.Initial Slope Time (s)0.0–25E.Weld Amperage (A)1–200G.Background Amperage (%)0–100H.Peak Percent Time (%)5–95I.Final Slope Time (s)0.0–25 J.Final Amperage (A)1–200L.Postflow Time (s) 0–0.50M.Dig (%)0–1003Performance DataAMPERES*115 VAC INPUTV O L T S0204060801001201400501001502002501401201006080402000 50 100 150 200 250AMPERES*OTHER INPUT VOLTAGESV O L T S*Amperage setting must be reduced toobtain currents less than highlighted data point.STICK MAX.TIG MAX.STICK/TIG MIN.DIG MAX.102030405060708090100% DUTY CYCLEDUTY CYCLE CHART250200150100500O U T P U T A M P E R E SIncluded AccessoriesNon-CE SD/DX Models Include:(2) International-style connectors 35/50(1) DA-917F torch adapter tointernational-style connector (#194 720)Non-CE LX Model Includes:(2) International-style connectors 35/50(1) 14-pin amphenol with clamp (1) 10-pin amphenol with clamp (1) 5/8 in - 18 gas fittingCE SD/DX Models Include:(2) International-style connectors 35/50(1) 14-pin amphenol with clamp (1) 5/8 in - 18 gas fitting (1) 3/8 in BSPP gas fittingOrdering InformationPower Source and Options Stock No.Description Qty.Price Maxstar®200 SD#903 701Basic controls for TIG/Stick, 120–460 VAC#903 768Basic controls for TIG/Stick, 120–460 VAC with CEMaxstar®200 DX#903 701-01-1Full-feature controls for TIG/Stick, 120–460 VAC#903 768-01-1Full-feature controls for TIG/Stick, 120–460 VAC with CEMaxstar®200 LX#903 701-01-2Full-feature controls with the required automation connections, 120–460 VACTIG AccessoriesTIG Torch Adapters#194 720DA-917F#190 219DA-1820L#194 724DA-26RContractor Kits#195 055150 A TIG/Stick with RCCS-14 fingertip control#195 054150 A TIG/Stick with RFCS-14 HD foot controlDiamondback™TIG Torches See Diamondback TIG Torch Selector GuideConsumables/Tungsten See Parts GuideGas Cylinder/Hose and FittingsRemote ControlsRFCS-14 HD#194 744Heavy-duty foot controlRCCS-14#043 688North/south fingertip controlRCC-14#151 086Side-to-side fingertip controlRMLS-14#129 337Momentary/maintained rocker controlRMS-14#187 208Momentary rubber dome switchExtension CordsCoolant SystemsCoolmate™3 #043 007115 VAC#043 007-01-2115 VAC with CE#043 008230 VAC#043 008-01-2230 VAC with CECoolmate™V3#043 009115 VAC#043 009-01-2115 VAC, 50/60 Hz with CECoolmate™4#042 288115 VAC#042 288-01-5115 VAC with CELow-Conductivity Coolant#043 810International-Style ConnectorsInternational-Style Connector Kit #042 418Dinse, (1) male plug-50 mmExtension Kit for International-Style#042 419Dinse, (1) plug and (1)receptacle-50 mmInternational/Tweco®Adapter #042 465 A one-piece adapter with International-style male plugInternational/Cam-Lok Adapter #042 466 A one-piece adapter with International-style male plugDate:Total Quoted Price:Distributed by:Litho in USA。

AUREL SAW 3V CS 发射器说明书

AUREL SAW 3V CS 发射器说明书

Instruction ManualTechnical features are subject to change without notice. AUR°EL S.p.A does not feel responsible for any damage caused by the device’s misuse.--------------------------------------------------------------------------------------------------------------------------------------------------------------------- TX SAW MID 3V/CS TRANSMITTERSAW Transmitter module with external antenna, for utilisations with ON-OFF modulation of a RF carrier with digital data. Buffer stage for enhanced power and low harmonics on output allowing high immunity against disadjustments.PIN-OUTCONNECTIONSPin 1 TX Dati Data input with minimum 50 kΩ input resistance. Pin 2-7-9 Ground GND Connections. To be externally connected to a single ground plate.Pin 8 RF output RF output with a characteristic impedence of 50Ω Pin 10 +VConnection to the positive pole of the 3V supplyTechnical features TX SAW MID 3VMin Tipic Max Unit Remarks Working frequency centre 433.82 433.92434.02MHz See notes 2 and3 Voltage supply (Vs) 1,8 3 3,5 VAbsorbed current2,4 5,5 7 mA See note 4 RF output power (E.R.P.) 3 10 11 dBm See note 2Output impedance pin 8 50 ΩRF spurious emissions -40 dBm See note 2Modulation frequency 5 10 KHzInput high logic level 1,8 3 3,5 V See note 1Input low logic level 0V 0,2 V Working temperature -20+80 °CDimensions25,4 x 12,43 x 2,5 mm110Instruction ManualTechnical features are subject to change without notice. AUR°EL S.p.A does not feel responsible for any damage caused by the device’s misuse.--------------------------------------------------------------------------------------------------------------------------------------------------------------------- NOTE 1: It is opportune that the max voltage applied to data input pin is equal to voltage supply.NOTE 2: Values have been obtained by applying the test system shown in Fig. 1 and maximum 3,5 V power supply. NOTE 3: The minimum and maximum showed values are determined by the device’s construction tolerance. NOTE 4: Values are determined by means of an input signal with duty cycle 50%.The declared technical features have been obtained by applying the following testing system:Fig.1Device usageIn order to obtain the performances described in the technical specifications and to comply with the operating conditions, which characterize the Certification, the transmitter has to be mounted on a printed circuit, and keep into consideration what follows:3V dc supply :1. The transmitter must be supplied by a very low voltage source, safely protected against short circuits . Maximum voltage variations allowed: 1,8÷3,5V.2. De-coupling, next to the transmitter, by means of a minimum 100.000 pF ceramic capacitor.Ground:It must surround at the best the welding area of the transmitter. The circuit must be double layer, with throughout vias to the ground planes, approximately each 15 mm.It must be properly dimensioned, especially in the antenna connection area, in case a radiating whip antenna is fitted in it (an area of approximately 50 mm radius is suggested).Instruction ManualTechnical features are subject to change without notice. AUR°EL S.p.A does not feel responsible for any damage caused by the device’s misuse.---------------------------------------------------------------------------------------------------------------------------------------------------------------------50 Ohm line:1. It must be the shortest as possible.2. 1,8 mm wide for 1 mm thick FR4 printed circuits and 2,9 mm wide for 1,6 mm thick FR4 printed circuits.It must be kept 3 mm away from the ground circuit on the same side. 3. On the opposite side a ground circuit area must be present.Antenna connection:1. It may be utilized as the direct connection point for the radiating whip antenna.2. It can bear the connection of the central wire of a 50 Ω coaxial cable. Be sure that the braid is welded tothe ground in a close point.Antenna1. A whip antenna, 16,5 mm long and approximately 1 mm dia, brass or copper wire made, must beconnected to the RF output of the transmitter (pin 8), (see fig. 2).2. The antenna body must be keep straight as much as possible and it must be free from other circuits ormetal parts (5 cm minimum suggested distance.)3. It can be utilized either vertically or horizontally, provided that a good ground plane surrounds theconnection point between antenna and transmitter output.N.B : As an alternative to the a.m. antenna it is possible to fit the whip model manufactured by AUR°EL (see related Data Sheet and Application Notes).By fitting whips too different from the described ones, the EEC Certification is not assured.Fig.2Instruction ManualOther components:1.Keep the transmitter separate from all other components of the circuit (more than 5 mm).2.Keep particularly far away and shielded all microprocessors and their clock circuits.3.Do not fit components around the 50 Ohm line. Keep them at least at 5 mm distance.4. If the Antenna Connection is directly used for a radiating whip connection, keep at least 5 cm radius freearea. In case a 50 Ω impedance coaxial cable is connected, then 5 mm radius will suffice.Reference RulesThe TX SAW MID 3V transmitter complies with the EU Rules EN 300-220 and EN 301-489, with a 3,5V max. supply. The equipment has been tested according to rule EN 60950 and it can be utilized inside a special insulated housing that assures its compliance with the above mentioned rule. The transmitter must be supplied by a very low voltage source, safely protected against short circuits.The use of the transmitter module is foreseen inside housings that assure the overcoming of the rules EN 61000 not directly applicable to the module itself. In particular, it is left at the User’s care, the insulation of the external antenna connection, and of the antenna itself, since the RF output of the transmitter is not built to directly bear the electrostatic charges foreseen by the EN 61000-4-2 rules.CEPT 70-03 RecommendationIn order to comply with such rule, the device must be used only for a 10% of an hourly duty-cycle,(that means 6 minutes of utilisation over 60). The device utilisation inside the italian territory is governed by the Codice Postale and Telecomunicazioni rules in force (art. no. 334 and subsequents).Technical features are subject to change without notice. AUR°EL S.p.A does not feel responsible for any damage caused by the device’s misuse.---------------------------------------------------------------------------------------------------------------------------------------------------------------------Instruction Manual Reference curvesFig. 3 RF Power Vs Voltage SupplyFig. 4 Absorbed Current Vs Voltage SupplyTechnical features are subject to change without notice. AUR°EL S.p.A does not feel responsible for any damage caused by the device’s misuse.---------------------------------------------------------------------------------------------------------------------------------------------------------------------Instruction ManualReference thermal curvesThe thermal curves have been obtained by the testing system shown in Fig.1Fig. 5 RF Power Delta Vs TemperatureFig. 6 Absorbed current Delta Vs TemperatureTechnical features are subject to change without notice. AUR°EL S.p.A does not feel responsible for any damage caused by the device’s misuse.---------------------------------------------------------------------------------------------------------------------------------------------------------------------Instruction ManualFig. 7 Frequency Delta Vs TemperatrureTechnical features are subject to change without notice. AUR°EL S.p.A does not feel responsible for any damage caused by the device’s misuse.---------------------------------------------------------------------------------------------------------------------------------------------------------------------。

e2356cpu参数

e2356cpu参数

e2356cpu参数全文共四篇示例，供读者参考第一篇示例：e2356是英特尔推出的一款高性能CPU处理器，针对服务器和工作站市场。

该处理器采用了新一代的制造工艺，拥有强大的性能和节能特性。

下面我们来详细介绍e2356的参数及性能优势。

让我们看一下e2356的基本参数。

该处理器采用了14纳米的制造工艺，拥有6个核心和12个线程。

主频为3.5GHz，最高睿频为4.2GHz。

缓存方面，L3缓存容量为12MB，内存支持方面支持DDR4-2666内存，最大支持内存频率为2933MHz。

功耗方面，TDP 为95W。

e2356采用了英特尔的架构设计，支持英特尔超线程技术，能够有效提高多线程处理性能。

在节能方面也有很大优势，支持英特尔动态功耗管理技术，能够根据实际需求调整功耗，保持系统稳定运行的同时尽可能降低能耗。

在性能方面，e2356拥有强大的运算能力和处理能力。

6个核心和12个线程的设计，能够有效处理多任务，提高系统运行效率。

处理器主频高达3.5GHz，最高睿频更是达到4.2GHz，能够快速响应各种任务处理需求。

12MB的L3缓存也能够有效减少内存访问延迟，提高数据读取速度。

在工作站和服务器市场上，性能和可靠性是用户最为看重的因素。

e2356采用了多种优化技术，如英特尔虚拟化技术、英特尔适应性性能加速器、英特尔高级向量扩展2.0等，能够提高处理器性能和数据处理速度，同时提高系统稳定性和数据安全性。

e2356还支持英特尔双通道内存技术，最大支持内存频率为2933MHz，能够提供更快的数据传输速度，降低系统内存访问时延。

支持DDR4-2666内存，能够提供更大的内存容量和更高的带宽，适用于大规模数据处理和运算需求。

第二篇示例：E2356cpu是一款高性能、低功耗的中央处理器，广泛用于PC、服务器和移动设备等领域。

本文将详细介绍E2356cpu的参数与特性。

E2356cpu采用了先进的制程工艺，拥有充足的计算资源和处理能力。

  1. 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

General DescriptionThe MAX220–MAX249 family of line drivers/receivers is intended for all EIA/TIA-232E and V.28/V.24 communica-tions interfaces, particularly applications where ±12V is not available.These parts are especially useful in battery-powered sys-tems, since their low-power shutdown mode reduces power dissipation to less than 5µW. The MAX225,MAX233, MAX235, and MAX245/MAX246/MAX247 use no external components and are recommended for appli-cations where printed circuit board space is critical.________________________ApplicationsPortable Computers Low-Power Modems Interface TranslationBattery-Powered RS-232 Systems Multidrop RS-232 NetworksNext-Generation Device Features♦For Low-Voltage, Integrated ESD ApplicationsMAX3222E/MAX3232E/MAX3237E/MAX3241E/MAX3246E: +3.0V to +5.5V, Low-Power, Up to 1Mbps, True RS-232 Transceivers Using Four 0.1µF External Capacitors (MAX3246E Available in a UCSP™Package)♦For Low-Cost ApplicationsMAX221E: ±15kV ESD-Protected, +5V, 1µA,Single RS-232 Transceiver with AutoShutdown™MAX220–MAX249+5V-Powered, Multichannel RS-232Drivers/Receivers________________________________________________________________Maxim Integrated Products 1Selection Table19-4323; Rev 15; 1/06Power No. of NominalSHDN RxPart Supply RS-232No. of Cap. Value & Three-Active in Data Rate Number (V)Drivers/Rx Ext. Caps (µF)State SHDN (kbps)FeaturesMAX220+52/240.047/0.33No —120Ultra-low-power, industry-standard pinout MAX222+52/2 4 0.1Yes —200Low-power shutdownMAX223 (MAX213)+54/54 1.0 (0.1)Yes ✔120MAX241 and receivers active in shutdown MAX225+55/50—Yes ✔120Available in SOMAX230 (MAX200)+55/04 1.0 (0.1)Yes —120 5 drivers with shutdownMAX231 (MAX201)+5 and2/2 2 1.0 (0.1)No —120Standard +5/+12V or battery supplies; +7.5 to +13.2same functions as MAX232MAX232 (MAX202)+52/24 1.0 (0.1)No —120 (64)Industry standardMAX232A+52/240.1No —200Higher slew rate, small caps MAX233 (MAX203)+52/20— No —120No external capsMAX233A+52/20—No —200No external caps, high slew rate MAX234 (MAX204)+54/04 1.0 (0.1)No —120Replaces 1488MAX235 (MAX205)+55/50—Yes —120No external capsMAX236 (MAX206)+54/34 1.0 (0.1)Yes —120Shutdown, three stateMAX237 (MAX207)+55/34 1.0 (0.1)No —120Complements IBM PC serial port MAX238 (MAX208)+54/44 1.0 (0.1)No —120Replaces 1488 and 1489MAX239 (MAX209)+5 and3/52 1.0 (0.1)No —120Standard +5/+12V or battery supplies;+7.5 to +13.2single-package solution for IBM PC serial port MAX240+55/54 1.0Yes —120DIP or flatpack package MAX241 (MAX211)+54/54 1.0 (0.1)Yes —120Complete IBM PC serial port MAX242+52/240.1Yes ✔200Separate shutdown and enableMAX243+52/240.1No —200Open-line detection simplifies cabling MAX244+58/104 1.0No —120High slew rateMAX245+58/100—Yes ✔120High slew rate, int. caps, two shutdown modes MAX246+58/100—Yes ✔120High slew rate, int. caps, three shutdown modes MAX247+58/90—Yes ✔120High slew rate, int. caps, nine operating modes MAX248+58/84 1.0Yes ✔120High slew rate, selective half-chip enables MAX249+56/1041.0Yes✔120Available in quad flatpack packageFor pricing, delivery, and ordering information,please contact Maxim/Dallas Direct!at 1-888-629-4642, or visit Maxim’s website at .Ordering InformationOrdering Information continued at end of data sheet.*Contact factory for dice specifications.AutoShutdown and UCSP are trademarks of Maxim Integrated Products, Inc.M A X 220–M A X 249+5V-Powered, Multichannel RS-232Drivers/Receivers 2_______________________________________________________________________________________ABSOLUTE MAXIMUM RATINGS—MAX220/222/232A/233A/242/243ELECTRICAL CHARACTERISTICS—MAX220/222/232A/233A/242/243Note 1:For the MAX220, V+ and V- can have a maximum magnitude of 7V, but their absolute difference cannot exceed 13V.Note 2:Input voltage measured with T OUT in high-impedance state, SHDN or V CC = 0V.Note 3:Maximum reflow temperature for the MAX233A is +225°C.Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.Supply Voltage (V CC )...............................................-0.3V to +6V V+ (Note 1)..................................................(V CC - 0.3V) to +14V V- (Note 1).............................................................+0.3V to +14V Input VoltagesT IN ..............................................................-0.3V to (V CC - 0.3V)R IN (Except MAX220)........................................................±30V R IN (MAX220).....................................................................±25V T OUT (Except MAX220) (Note 2).......................................±15V T OUT (MAX220)...............................................................±13.2V Output VoltagesT OUT ...................................................................................±15V R OUT .........................................................-0.3V to (V CC + 0.3V)Driver/Receiver Output Short Circuited to GND.........Continuous Continuous Power Dissipation (T A = +70°C)16-Pin Plastic DIP (derate 10.53mW/°C above +70°C)..842mW18-Pin Plastic DIP (derate 11.11mW/°C above +70°C)..889mW 20-Pin Plastic DIP (derate 8.00mW/°C above +70°C)..440mW 16-Pin Narrow SO (derate 8.70mW/°C above +70°C)...696mW 16-Pin Wide SO (derate 9.52mW/°C above +70°C)......762mW 18-Pin Wide SO (derate 9.52mW/°C above +70°C)......762mW 20-Pin Wide SO (derate 10.00mW/°C above +70°C)....800mW 20-Pin SSOP (derate 8.00mW/°C above +70°C)..........640mW 16-Pin CERDIP (derate 10.00mW/°C above +70°C).....800mW 18-Pin CERDIP (derate 10.53mW/°C above +70°C).....842mW Operating Temperature RangesMAX2_ _AC_ _, MAX2_ _C_ _.............................0°C to +70°C MAX2_ _AE_ _, MAX2_ _E_ _..........................-40°C to +85°C MAX2_ _AM_ _, MAX2_ _M_ _.......................-55°C to +125°C Storage Temperature Range.............................-65°C to +160°C Lead Temperature (soldering, 10s) (Note 3)...................+300°CMAX220–MAX249+5V-Powered, Multichannel RS-232Drivers/Receivers_______________________________________________________________________________________3Note 4:MAX243 R2OUT IN ELECTRICAL CHARACTERISTICS—MAX220/222/232A/233A/242/243 (continued)M A X 220–M A X 249+5V-Powered, Multichannel RS-232Drivers/Receivers 4_________________________________________________________________________________________________________________________________Typical Operating CharacteristicsMAX220/MAX222/MAX232A/MAX233A/MAX242/MAX243108-1051525OUTPUT VOLTAGE vs. LOAD CURRENT-4-6-8-2642LOAD CURRENT (mA)O U T P U T V O L T A G E (V )1002011104104060AVAILABLE OUTPUT CURRENTvs. DATA RATE65798DATA RATE (kb/s)O U T P U T C U R R E N T (m A )203050+10V-10VMAX222/MAX242ON-TIME EXITING SHUTDOWN+5V +5V 0V0V 500μs/div V +, V - V O L T A G E (V )ELECTRICAL CHARACTERISTICS—MAX220/222/232A/233A/242/243 (continued)(V CC = +5V ±10%, C1–C4 = 0.1µF‚ MAX220, C1 = 0.047µF, C2–C4 = 0.33µF, T A = T MIN to T MAX ‚ unless otherwise noted.)MAX220–MAX249+5V-Powered, Multichannel RS-232Drivers/Receivers_______________________________________________________________________________________5V CC ...........................................................................-0.3V to +6V V+................................................................(V CC - 0.3V) to +14V V-............................................................................+0.3V to -14V Input VoltagesT IN ............................................................-0.3V to (V CC + 0.3V)R IN ......................................................................................±30V Output VoltagesT OUT ...................................................(V+ + 0.3V) to (V- - 0.3V)R OUT .........................................................-0.3V to (V CC + 0.3V)Short-Circuit Duration, T OUT ......................................Continuous Continuous Power Dissipation (T A = +70°C)14-Pin Plastic DIP (derate 10.00mW/°C above +70°C)....800mW 16-Pin Plastic DIP (derate 10.53mW/°C above +70°C)....842mW 20-Pin Plastic DIP (derate 11.11mW/°C above +70°C)....889mW 24-Pin Narrow Plastic DIP(derate 13.33mW/°C above +70°C)..........1.07W24-Pin Plastic DIP (derate 9.09mW/°C above +70°C)......500mW 16-Pin Wide SO (derate 9.52mW/°C above +70°C).........762mW20-Pin Wide SO (derate 10.00mW/°C above +70°C).......800mW 24-Pin Wide SO (derate 11.76mW/°C above +70°C).......941mW 28-Pin Wide SO (derate 12.50mW/°C above +70°C) .............1W 44-Pin Plastic FP (derate 11.11mW/°C above +70°C).....889mW 14-Pin CERDIP (derate 9.09mW/°C above +70°C)..........727mW 16-Pin CERDIP (derate 10.00mW/°C above +70°C)........800mW 20-Pin CERDIP (derate 11.11mW/°C above +70°C)........889mW 24-Pin Narrow CERDIP(derate 12.50mW/°C above +70°C)..............1W24-Pin Sidebraze (derate 20.0mW/°C above +70°C)..........1.6W 28-Pin SSOP (derate 9.52mW/°C above +70°C).............762mW Operating Temperature RangesMAX2 _ _ C _ _......................................................0°C to +70°C MAX2 _ _ E _ _...................................................-40°C to +85°C MAX2 _ _ M _ _......................................................-55°C to +125°C Storage Temperature Range.............................-65°C to +160°C Lead Temperature (soldering, 10s) (Note 4)...................+300°CABSOLUTE MAXIMUM RATINGS—MAX223/MAX230–MAX241ELECTRICAL CHARACTERISTICS—MAX223/MAX230–MAX241(MAX223/230/232/234/236/237/238/240/241, V CC = +5V ±10; MAX233/MAX235, V CC = 5V ±5%‚ C1–C4 = 1.0µF; MAX231/MAX239,V CC = 5V ±10%; V+ = 7.5V to 13.2V; T A = T MIN to T MAX ; unless otherwise noted.)Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.Note 4:Maximum reflow temperature for the MAX233/MAX235 is +225°C.M A X 220–M A X 249+5V-Powered, Multichannel RS-232Drivers/Receivers 6_______________________________________________________________________________________ELECTRICAL CHARACTERISTICS—MAX223/MAX230–MAX241 (continued)(MAX223/230/232/234/236/237/238/240/241, V CC = +5V ±10; MAX233/MAX235, V CC = 5V ±5%‚ C1–C4 = 1.0µF; MAX231/MAX239,V CC = 5V ±10%; V+ = 7.5V to 13.2V; T A = T MIN to T MAX ; unless otherwise noted.)MAX220–MAX249+5V-Powered, Multichannel RS-232Drivers/Receivers_______________________________________________________________________________________78.56.54.55.5TRANSMITTER OUTPUT VOLTAGE (V OH ) vs. V CC7.08.0V CC (V)V O H (V )5.07.57.46.02500TRANSMITTER OUTPUT VOLTAGE (V OH )vs. LOAD CAPACITANCE AT DIFFERENT DATA RATES6.46.27.27.0LOAD CAPACITANCE (pF)V O H (V )1500100050020006.86.612.04.02500TRANSMITTER SLEW RATE vs. LOAD CAPACITANCE6.05.011.09.010.0LOAD CAPACITANCE (pF)S L E W R A T E (V /μs )1500100050020008.07.0-6.0-9.04.55.5TRANSMITTER OUTPUT VOLTAGE (V OL ) vs. V CC-8.0-8.5-6.5-7.0V CC (V)V O L (V )5.0-7.5-6.0-7.62500TRANSMITTER OUTPUT VOLTAGE (V OL )vs. LOAD CAPACITANCE AT DIFFERENT DATA RATES-7.0-7.2-7.4-6.2-6.4LOAD CAPACITANCE (pF)V O L (V )150010005002000-6.6-6.810-105101520253035404550TRANSMITTER OUTPUT VOLTAGE (V+, V-)vs. LOAD CURRENT-2-6-4-886CURRENT (mA)V +, V - (V )420__________________________________________Typical Operating CharacteristicsMAX223/MAX230–MAX241*SHUTDOWN POLARITY IS REVERSED FOR NON MAX241 PARTSV+, V- WHEN EXITING SHUTDOWN(1μF CAPACITORS)MAX220-13SHDN*V-O V+500ms/divM A X 220–M A X 249+5V-Powered, Multichannel RS-232Drivers/Receivers 8_______________________________________________________________________________________ABSOLUTE MAXIMUM RATINGS—MAX225/MAX244–MAX249ELECTRICAL CHARACTERISTICS—MAX225/MAX244–MAX249(MAX225, V CC = 5.0V ±5%; MAX244–MAX249, V CC = +5.0V ±10%, external capacitors C1–C4 = 1µF; T A = T MIN to T MAX ; unless oth-erwise noted.)Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.Supply Voltage (V CC )...............................................-0.3V to +6V Input VoltagesT IN ‚ ENA , ENB , ENR , ENT , ENRA ,ENRB , ENTA , ENTB ..................................-0.3V to (V CC + 0.3V)R IN .....................................................................................±25V T OUT (Note 5).....................................................................±15V R OUT ........................................................-0.3V to (V CC + 0.3V)Short Circuit (one output at a time)T OUT to GND............................................................Continuous R OUT to GND............................................................ContinuousContinuous Power Dissipation (T A = +70°C)28-Pin Wide SO (derate 12.50mW/°C above +70°C).............1W 40-Pin Plastic DIP (derate 11.11mW/°C above +70°C)...611mW 44-Pin PLCC (derate 13.33mW/°C above +70°C)...........1.07W Operating Temperature RangesMAX225C_ _, MAX24_C_ _ ..................................0°C to +70°C MAX225E_ _, MAX24_E_ _ ...............................-40°C to +85°C Storage Temperature Range.............................-65°C to +160°C Lead Temperature (soldering,10s) (Note 6)....................+300°CNote 5:Input voltage measured with transmitter output in a high-impedance state, shutdown, or V CC = 0V.Note 6:Maximum reflow temperature for the MAX225/MAX245/MAX246/MAX247 is +225°C.MAX220–MAX249+5V-Powered, Multichannel RS-232Drivers/Receivers_______________________________________________________________________________________9Note 7:The 300Ωminimum specification complies with EIA/TIA-232E, but the actual resistance when in shutdown mode or V CC =0V is 10M Ωas is implied by the leakage specification.ELECTRICAL CHARACTERISTICS—MAX225/MAX244–MAX249 (continued)(MAX225, V CC = 5.0V ±5%; MAX244–MAX249, V CC = +5.0V ±10%, external capacitors C1–C4 = 1µF; T A = T MIN to T MAX ; unless oth-erwise noted.)M A X 220–M A X 249+5V-Powered, Multichannel RS-232Drivers/Receivers 10________________________________________________________________________________________________________________________________Typical Operating CharacteristicsMAX225/MAX244–MAX24918212345TRANSMITTER SLEW RATE vs. LOAD CAPACITANCE86416LOAD CAPACITANCE (nF)T R A N S M I T T E R S L E W R A T E (V /μs )14121010-105101520253035OUTPUT VOLTAGEvs. LOAD CURRENT FOR V+ AND V--2-4-6-88LOAD CURRENT (mA)O U T P U T V O L T A G E (V )64209.05.012345TRANSMITTER OUTPUT VOLTAGE (V+, V-)vs. LOAD CAPACITANCE AT DIFFERENT DATA RATES6.05.58.5LOAD CAPACITANCE (nF)V +, V (V )8.07.57.06.5MAX220–MAX249Drivers/ReceiversFigure 1. Transmitter Propagation-Delay Timing Figure 2. Receiver Propagation-Delay TimingFigure 3. Receiver-Output Enable and Disable Timing Figure 4. Transmitter-Output Disable TimingM A X 220–M A X 249Drivers/Receivers ENT ENR OPERATION STATUS TRANSMITTERSRECEIVERS00Normal Operation All Active All Active 01Normal Operation All Active All 3-State10Shutdown All 3-State All Low-Power Receive Mode 11ShutdownAll 3-StateAll 3-StateTable 1a. MAX245 Control Pin ConfigurationsENT ENR OPERATION STATUS TRANSMITTERS RECEIVERSTA1–TA4TB1–TB4RA1–RA5RB1–RB500Normal Operation All Active All Active All Active All Active 01Normal Operation All Active All Active RA1–RA4 3-State,RA5 Active RB1–RB4 3-State,RB5 Active 1ShutdownAll 3-StateAll 3-StateAll Low-Power Receive Mode All Low-Power Receive Mode 11Shutdown All 3-State All 3-StateRA1–RA4 3-State,RA5 Low-Power Receive ModeRB1–RB4 3-State,RB5 Low-Power Receive ModeTable 1b. MAX245 Control Pin ConfigurationsTable 1c. MAX246 Control Pin ConfigurationsENA ENB OPERATION STATUS TRANSMITTERS RECEIVERSTA1–TA4TB1–TB4RA1–RA5RB1–RB500Normal Operation All Active All Active All Active All Active 01Normal Operation All Active All 3-State All Active RB1–RB4 3-State,RB5 Active 1ShutdownAll 3-StateAll ActiveRA1–RA4 3-State,RA5 Active All Active 11Shutdown All 3-State All 3-StateRA1–RA4 3-State,RA5 Low-Power Receive ModeRB1–RB4 3-State,RA5 Low-Power Receive ModeMAX220–MAX249Drivers/ReceiversM A X 220–M A X 249_______________Detailed DescriptionThe MAX220–MAX249 contain four sections: dual charge-pump DC-DC voltage converters, RS-232 dri-vers, RS-232 receivers, and receiver and transmitter enable control inputs.Dual Charge-Pump Voltage ConverterThe MAX220–MAX249 have two internal charge-pumps that convert +5V to ±10V (unloaded) for RS-232 driver operation. The first converter uses capacitor C1 to dou-ble the +5V input to +10V on C3 at the V+ output. The second converter uses capacitor C2 to invert +10V to -10V on C4 at the V- output.A small amount of power may be drawn from the +10V (V+) and -10V (V-) outputs to power external circuitry (see the Typical Operating Characteristics section),except on the MAX225 and MAX245–MAX247, where these pins are not available. V+ and V- are not regulated,so the output voltage drops with increasing load current.Do not load V+ and V- to a point that violates the mini-mum ±5V EIA/TIA-232E driver output voltage when sourcing current from V+ and V- to external circuitry. When using the shutdown feature in the MAX222,MAX225, MAX230, MAX235, MAX236, MAX240,MAX241, and MAX245–MAX249, avoid using V+ and V-to power external circuitry. When these parts are shut down, V- falls to 0V, and V+ falls to +5V. For applica-tions where a +10V external supply is applied to the V+pin (instead of using the internal charge pump to gen-erate +10V), the C1 capacitor must not be installed and the SHDN pin must be tied to V CC . This is because V+is internally connected to V CC in shutdown mode.RS-232 DriversThe typical driver output voltage swing is ±8V when loaded with a nominal 5k ΩRS-232 receiver and V CC =+5V. Output swing is guaranteed to meet the EIA/TIA-232E and V.28 specification, which calls for ±5V mini-mum driver output levels under worst-case conditions.These include a minimum 3k Ωload, V CC = +4.5V, and maximum operating temperature. Unloaded driver out-put voltage ranges from (V+ -1.3V) to (V- +0.5V).Input thresholds are both TTL and CMOS compatible.The inputs of unused drivers can be left unconnected since 400k Ωinput pullup resistors to V CC are built in (except for the MAX220). The pullup resistors force the outputs of unused drivers low because all drivers invert.The internal input pullup resistors typically source 12µA,except in shutdown mode where the pullups are dis-abled. Driver outputs turn off and enter a high-imped-ance state—where leakage current is typically microamperes (maximum 25µA)—when in shutdownmode, in three-state mode, or when device power is removed. Outputs can be driven to ±15V. The power-supply current typically drops to 8µA in shutdown mode.The MAX220 does not have pullup resistors to force the outputs of the unused drivers low. Connect unused inputs to GND or V CC .The MAX239 has a receiver three-state control line, and the MAX223, MAX225, MAX235, MAX236, MAX240,and MAX241 have both a receiver three-state control line and a low-power shutdown control. Table 2 shows the effects of the shutdown control and receiver three-state control on the receiver outputs.The receiver TTL/CMOS outputs are in a high-imped-ance, three-state mode whenever the three-state enable line is high (for the MAX225/MAX235/MAX236/MAX239–MAX241), and are also high-impedance whenever the shutdown control line is high.When in low-power shutdown mode, the driver outputs are turned off and their leakage current is less than 1µA with the driver output pulled to ground. The driver output leakage remains less than 1µA, even if the transmitter output is backdriven between 0V and (V CC + 6V). Below -0.5V, the transmitter is diode clamped to ground with 1k Ωseries impedance. The transmitter is also zener clamped to approximately V CC + 6V, with a series impedance of 1k Ω.The driver output slew rate is limited to less than 30V/µs as required by the EIA/TIA-232E and V.28 specifica-tions. Typical slew rates are 24V/µs unloaded and 10V/µs loaded with 3Ωand 2500pF.RS-232 ReceiversEIA/TIA-232E and V.28 specifications define a voltage level greater than 3V as a logic 0, so all receivers invert.Input thresholds are set at 0.8V and 2.4V, so receivers respond to TTL level inputs as well as EIA/TIA-232E and V.28 levels.The receiver inputs withstand an input overvoltage up to ±25V and provide input terminating resistors withDrivers/ReceiversTable 2. Three-State Control of ReceiversMAX220–MAX249Drivers/Receiversnominal 5k Ωvalues. The receivers implement Type 1interpretation of the fault conditions of V.28 and EIA/TIA-232E.The receiver input hysteresis is typically 0.5V with a guaranteed minimum of 0.2V. This produces clear out-put transitions with slow-moving input signals, even with moderate amounts of noise and ringing. The receiver propagation delay is typically 600ns and is independent of input swing direction.Low-Power Receive ModeThe low-power receive mode feature of the MAX223,MAX242, and MAX245–MAX249 puts the IC into shut-down mode but still allows it to receive information. This is important for applications where systems are periodi-cally awakened to look for activity. Using low-power receive mode, the system can still receive a signal that will activate it on command and prepare it for communi-cation at faster data rates. This operation conserves system power.Negative Threshold—MAX243The MAX243 is pin compatible with the MAX232A, differ-ing only in that RS-232 cable fault protection is removed on one of the two receiver inputs. This means that control lines such as CTS and RTS can either be driven or left floating without interrupting communication. Different cables are not needed to interface with different pieces of equipment.The input threshold of the receiver without cable fault protection is -0.8V rather than +1.4V. Its output goes positive only if the input is connected to a control line that is actively driven negative. If not driven, it defaults to the 0 or “OK to send” state. Normally‚ the MAX243’s other receiver (+1.4V threshold) is used for the data line (TD or RD)‚ while the negative threshold receiver is con-nected to the control line (DTR‚ DTS‚ CTS‚ RTS, etc.). Other members of the RS-232 family implement the optional cable fault protection as specified by EIA/TIA-232E specifications. This means a receiver output goes high whenever its input is driven negative‚ left floating‚or shorted to ground. The high output tells the serial communications IC to stop sending data. To avoid this‚the control lines must either be driven or connected with jumpers to an appropriate positive voltage level.Shutdown—MAX222–MAX242On the MAX222‚ MAX235‚ MAX236‚ MAX240‚ and MAX241‚ all receivers are disabled during shutdown.On the MAX223 and MAX242‚ two receivers continue to operate in a reduced power mode when the chip is in shutdown. Under these conditions‚ the propagation delay increases to about 2.5µs for a high-to-low input transition. When in shutdown, the receiver acts as a CMOS inverter with no hysteresis. The MAX223 and MAX242 also have a receiver output enable input (EN for the MAX242 and EN for the MAX223) that allows receiver output control independent of SHDN (SHDN for MAX241). With all other devices‚ SHDN (SH DN for MAX241) also disables the receiver outputs.The MAX225 provides five transmitters and five receivers‚ while the MAX245 provides ten receivers and eight transmitters. Both devices have separate receiver and transmitter-enable controls. The charge pumps turn off and the devices shut down when a logic high is applied to the ENT input. In this state, the supply cur-rent drops to less than 25µA and the receivers continue to operate in a low-power receive mode. Driver outputs enter a high-impedance state (three-state mode). On the MAX225‚ all five receivers are controlled by the ENR input. On the MAX245‚ eight of the receiver out-puts are controlled by the ENR input‚ while the remain-ing two receivers (RA5 and RB5) are always active.RA1–RA4 and RB1–RB4 are put in a three-state mode when ENR is a logic high.Receiver and Transmitter EnableControl InputsThe MAX225 and MAX245–MAX249 feature transmitter and receiver enable controls.The receivers have three modes of operation: full-speed receive (normal active)‚ three-state (disabled)‚ and low-power receive (enabled receivers continue to function at lower data rates). The receiver enable inputs control the full-speed receive and three-state modes. The transmitters have two modes of operation: full-speed transmit (normal active) and three-state (disabled). The transmitter enable inputs also control the shutdown mode. The device enters shutdown mode when all transmitters are disabled. Enabled receivers function in the low-power receive mode when in shutdown.M A X 220–M A X 249Tables 1a–1d define the control states. The MAX244has no control pins and is not included in these tables. The MAX246 has ten receivers and eight drivers with two control pins, each controlling one side of the device. A logic high at the A-side control input (ENA )causes the four A-side receivers and drivers to go into a three-state mode. Similarly, the B-side control input (ENB ) causes the four B-side drivers and receivers to go into a three-state mode. As in the MAX245, one A-side and one B-side receiver (RA5 and RB5) remain active at all times. The entire device is put into shut-down mode when both the A and B sides are disabled (ENA = ENB = +5V).The MAX247 provides nine receivers and eight drivers with four control pins. The ENRA and ENRB receiver enable inputs each control four receiver outputs. The ENTA and ENTB transmitter enable inputs each control four drivers. The ninth receiver (RB5) is always active.The device enters shutdown mode with a logic high on both ENTA and ENTB .The MAX248 provides eight receivers and eight drivers with four control pins. The ENRA and ENRB receiver enable inputs each control four receiver outputs. The ENTA and ENTB transmitter enable inputs control four drivers each. This part does not have an always-active receiver. The device enters shutdown mode and trans-mitters go into a three-state mode with a logic high on both ENTA and ENTB .The MAX249 provides ten receivers and six drivers with four control pins. The ENRA and ENRB receiver enable inputs each control five receiver outputs. The ENTA and ENTB transmitter enable inputs control three dri-vers each. There is no always-active receiver. The device enters shutdown mode and transmitters go into a three-state mode with a logic high on both ENTA and ENTB . In shutdown mode, active receivers operate in a low-power receive mode at data rates up to 20kb/s.__________Applications InformationFigures 5 through 25 show pin configurations and typi-cal operating circuits. In applications that are sensitive to power-supply noise, V CC should be decoupled to ground with a capacitor of the same value as C1 and C2 connected as close as possible to the device.Drivers/Receivers。

相关文档
最新文档