MSDS-热熔胶

热熔胶MSDS英文版

PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS1 CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONPRODUCTProduct Name: HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSProduct Description: HOT MELT ADHESIVE,MIXTUREProduct Code:Intended Use: ADHESIVE,FOR AUTOMOBILE LAMPSCOMPANY IDENTIFICATIONHuangshan Xiuning Xindecheng Chemical Co., Ltd.SUPPLIER:Wanning Industrial Park, Huangshan, Anhui, China (245400)Telephone: 0086-559-7519970Facsimile: 0086-559-7519971This (M)SDS is a generic document with no country specific information included.2 COMPOSITION/INFORMATION ON INGREDIENTSNo Reportable Hazardous Substance(s) or Complex Substance(s).INGREDIENTS CAS No.Approx. Proportionstyrene butadiene rubber9003-55-8Med 50-60%rosin resin8050-09-7Low 50-40%PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS3 HAZARDS IDENTIFICATIONThis material is not considered to be hazardous.PHYSICAL / CHEMICAL HAZARDSN/AHEALTH HAZARDSNo adverse effects due to inhalation are expected. When heated, the vapour/fumes given off may cause respiratory tract irritation.4 FIRST AID MEASURESINHALATIONIn case of adverse exposure to vapors and / or aerosols formed at elevated temperatures, immediately remove the affected victim from exposure. Administer artificial respiration if breathing is stopped. Keep at rest.SKIN CONTACTWash contact areas with soap and water. For hot product: Immediately immerse in or flush affected area with large amounts of cold water to dissipate heat. Cover with clean cotton sheeting or gauze and get prompt medical attention.EYE CONTACTFlush thoroughly with water. If irritation occurs, get medical assistance.INGESTIONFirst aid is normally not required. Seek medical attention if discomfort occurs.5 FIRE- FIGHTING MEASURESPRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSEXTINGUISHING MEDIAAppropriate Extinguishing Media: Use dry chemical or carbon dioxide (CO2) to extinguish flames.Inappropriate Extinguishing Media: Straight streams of waterFIRE FIGHTINGFire Fighting Instructions: Assure an extended cooling down period to prevent re-ignition. Evacuate area. Prevent run-off from fire control or dilution from entering streams, sewers or drinking water supply.Hazardous Combustion Products: Flammable hydrocarbons, Oxides of carbon, Smoke, Fume, Incompletecombustion products6 ACCIDENTAL RELEASE MEASURESNOTIFICATION PROCEDURESIn the event of a spill or accidental release, notify relevant authorities in accordance with all applicable regulations.ENVIRONMENTAL PRECAUTIONSN/A7 HANDLING AND STORAGEHANDLINGAvoid elevated temperatures for prolonged periods of time. Protect material from direct sunlight. Material canaccumulate static charges which may cause an electrical spark (ignition source). Apart from the specific nature of the polymer product, conditions such as humidity, sunlight and temperature.Loading/Unloading Temperature: [Ambient]Transport Temperature: [Ambient]PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSSTORAGEStore in a cool, dry place.Storage Temperature: 0℃—40℃Storage Pressure:[Ambient]8 EXPOSURE CONTROLS /PERSONAL PROTECTIONENGINEERING CONTROLSN/APERSONAL PROTECTIONPersonal protective equipment selections vary based on potential exposure conditions such as applications, handling practices, concentration and ventilation. Information on the selection of protective equipment for use with this material, as provided below, is based upon intended, normal usage.Respiratory Protection:If engineering controls do not maintain airborne contaminant concentrations at a level which is adequate to protect worker health, an approved respirator may be appropriate. Respirator selection, use, and maintenance must be in accordance with regulatory requirements, if applicable. Types of respirators to be considered for this material include:No special requirements under ordinary conditions of use and with adequate ventilation.For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode.Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate, gas/vapour warning properties are poor, or if air purifying filter capacity/rating may be exceeded.Hand Protection:If product is hot, thermally protective gloves are recommended. If contact with forearms is likely, wear gauntlet style gloves.PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSEye Protection:If contact is likely, safety glasses with side shields are recommended.Skin and Body Protection:If product is hot, thermally protective, chemical resistant apron and long sleeves are recommended.Specific Hygiene Measures:Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned. Practice good housekeeping.9 PHYSICAL AND CHEMICAL PROPERTIESTypical physical and chemical properties are given below. Consult the Supplier in Section 1 for additional data. GENERAL INFORMATIONPhysical State: SolidForm: GrainsColour: GrayOdour: None to MildIMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATIONRelative Density (at 18 C): 0.97Density (at 18 ºC): 970 kg/m³Flash Point [method]: O.C Cleveland Open Cup ＞260℃Flammable Limits (Approximate volume % in air): LEL: N/D UEL: N/DAutoignition Temperature: N/APRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSBoiling Point / Range: ＞260℃Vapour Density (Air = 1): N/AVapour Pressure: N/AEvaporation Rate (N-Butyl Acetate = 1): N/ApH: N/ALog Pow (n-Octanol/Water Partition Coefficient): N/ASolubility in Water: Negligible10 STABILITY AND REACTIVITYSTABILITY:Material is stable under normal conditions.CONDITIONS TO AVOID:Avoid elevated temperatures for prolonged periods of time.HAZARDOUS DECOMPOSITION PRODUCTS:Material does not decompose at ambient temperatures. HAZARDOUS POLYMERIZATION:Will not occur.11 TOXICOLOGICAL INFORMATIONPRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSAcute ToxicityRoute of Exposure Conclusion / RemarksINHALATIONToxicity: Minimally Toxic. Based on test data for structurally similarmaterials.Irritation: Negligible hazard at ambient/normal handling temperatures. Basedon test data for structurally similar materials.INGESTIONToxicity: Minimally Toxic. Based on test data for structurally similarmaterials.SkinToxicity: Minimally Toxic. Based on test data for structurally similarmaterials.Irritation: Negligible irritation to skin at ambient temperatures. Based on testdata for structurally similar materials.EyeIrritation: May cause mild, short-lasting discomfort to eyes. Based on testdata for structurally similar materials.CHRONIC/OTHER EFFECTS12 ECOLOGICAL INFORMATIONThe information given is based on data available for the material, the components of the material, and similar materials. ECOTOXICITYPRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSMaterial -- Not expected to be harmful to aquatic organisms.Material -- Not expected to be harmful to terrestrial organisms13 DISPOSAL CONSIDERATIONSDisposal recommendations based on material as supplied. Disposal must be in accordance with current applicable laws and regulations, and material characteristics at time of disposal.DISPOSAL RECOMMENDATIONSSuitable routes of disposal are supervised incineration, preferentially with energy recovery, or appropriate recycling methods in accordance with applicable regulations and material characteristics at the time of disposal.14 TRANSPORT INFORMATIONLAND : Not Regulated for Land TransportSEA (IMDG) : Not Regulated for Sea Transport according to IMDG-CodeAIR (IATA) : Not Regulated for Air Transport15 RRGULATORY INFORMATIONPRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSMaterial is not hazardous as defined by the EU Dangerous Substances/Preparations Directives.16 OTHER INFORMATIONN/D = Not determined, N/A = Not applicableTHIS SDS COVERS THE FOLLOWING MATERIALS: Petroleum hydrocarbon resin ECR 807 | Escorez 2203 LC | mixed resin dust-----------------------------------------------------------------------------------------------------------------------------------------------------The information and recommendations contained herein are, to the best of Xindecheng’s knowledge and belief, accurate and reliable as of the date issued. You can contact Xindecheng to insure that this document is the most current available from Jinsen. The information and recommendations are offered for the user's consideration and examination. It is the user's responsibility to satisfy itself that the product is suitable for the intended use. If buyer repackages this product, it is the user's responsibility to insure proper health, safety and other necessary information is included with and/or on the container. Appropriate warnings and safe-handling procedures should be provided to handlers and users. Alteration of this document is strictly prohibited.---------------------------------------------------------------------------------------------------------------------------。

（2）盛装热熔胶的容器及预热槽须盖紧，以防污染。
（3）在正确操作指导书的情况下无危害。
（4）建议“先进—先用”循环使用。
急救措施
皮肤接触：用大量清水冲洗进行冷却。严重者需要立即送医院就医。
眼睛接触：用大量清水冲洗进行冲洗，并且立即送医院就医。
吸入：应速带离现场，至空气清新处。保持环境通风。源自食入：立即就医。标识
中文名：边胶（热熔胶）
英文名：ethylene-vinylacetate copolyme
分子式：/
相对分子质量：/
CAS号：/
危险性类别：/
化学类别：/
组成与
性状
主要成分：ethylene-vinylacetate copolyme
外观与形状：/
主要用途：书籍订装用。
健康危害
（1）由于热熔胶施工时必须加热，利用保护手套及衣物以策安全。
理化特性
物理状态：固体
颜色：白
气味：刺激气味
PH值：/
熔点：77℃--87℃
沸点：> 220℃
饱和蒸汽压（kpa）：20℃时<0.1mbar
相对密度（水=1）：20℃时1.0g/cm3
溶解：20℃时不溶于水。
粘性：160℃时4400-6000Mpa
灭火方法：泡沫、二氧化碳、干粉。
对消防人员要求：必须佩防护装备。
废弃
（1）将空容器或未用的产品返回给供应商。
（2）不可自行扔掉空容器或未用的产品。
运输信息
危规号：/
UN编号：/
包装分类：/
包装标志：/
包装方法：/
法规信息
（1）不必用危险警示，根据德国易燃液体管理规定，本产品属非易燃物；
（2）根据德国检测方法的分类（1999/5/17），本产品不危害水源。

热熔胶

闪火点：33
自然温度：34
爆炸界限：35
蒸气压：36
蒸气密度：37
密度：38
溶解度：39
一十、安定性及反应性
安定性；40
特殊状况下可能之危害反应：41
应避免之状况：42
应避免之物质：43
危害分解物：44
十一、毒性资料
45
十二、生态资料
46
十三、废弃处置方法：
47
十四、运送资料
48
十五、法规资料
49
十六、其他资料
物质安全资料表（MSDS）
一、物品与厂商资料
物品名称：1
制造商或供应商：2地址：3来自电话：4二、成分辨识资料
纯物质：
中英文名称：5
同义名称：6
化学文摘社登记号码(CAS No.)：7
化学式：8危害物质成分(百分比)：9
混合物：
化学性质：10
危害物质成分之中英文名称
浓度或浓度范围(成分百分比)
危害物质分类及图式
参考文献
50
制表单位
名称：51
地址/电话：52
制表人
53
制表日期
54
11
12
13
14
15
16
三、危害辨识资料
危险性类别：17
侵入途径：18
健康危害：19
燃爆危险：20
四、急救措施
21
五、灭火措施
22
六、泄漏处理方法
23
七、安全处置与储存方法
24
八、暴露预防措施：
25
九、物理及化学性质
物质状态：26
形状：27
颜色：28
气味：29
PH值：30
沸点/沸点范围：31
分解温度：32

MSDS-06热熔胶

化学品名称：热熔胶编号：MSDS--06
第一部分：化学品名称
化学品中文名称：乙烯-醋酸乙烯共聚物化学品英文名称：ethylene-vinyl acetate copolymer
中文名称2：英文名称2：EVA
CAS No.：24937-78-8
第二部分：成分/组成信息
有害物成分含量 CAS No.
乙烯-醋酸乙烯共聚物100%24937-78-8
第十一部分：毒理学资料
急性毒性：LD50：无资料 LC50：无资料
亚急性和慢性毒性：无资料刺激性：无资料致敏性：无资料
致突变性：无资料致畸性：无资料致癌性：无资料
第十二部分：生态学资料
生态毒理毒性：无资料生物降解性：无资料非生物降解性：无资料
生物富集或生物积累性：无资料其它有害作用：无资料。
第十三部分：废弃处置
第七部分：操作处置与储存
操作注意事项：密闭操作。密闭操作，提供良好的自然通风条件。操作人员必须经过专门培训，严格遵守操作规程。建议操作人员佩戴自吸过滤式防尘口罩，戴化学安全防护眼镜，穿防毒物渗透工作服，戴橡胶手套。远离火种、热源，工作场所严禁吸烟。使用防爆型的通风系统和设备。避免产生粉尘。避免与氧化剂、碱类接触。搬运时要轻装轻卸，防止包装及容器损坏。配备相应品种和数量的消防器材及泄漏应急处理设备。倒空的容器可能残留有害物。
第十五部分：法规信息
法规信息：化学危险物品安全管理条例 (1987年2月17日国务院发布)，化学危险物品安全管理条例实施细则 (化劳发[1992] 677号)，工作场所安全使用化学品规定 ([1996]劳部发423号)等法规，针对化学危险品的安全使用、生产、储存、运输、装卸等方面均作了相应规定。
第十六部分：其他ቤተ መጻሕፍቲ ባይዱ息

5-热熔胶粉MSDS

灭火时可能遭遇之特殊危害：产生一氧化碳、氧化氮。—Special Exposure Hazards:Formation of carbon monoxide ,nitrogenoxides,of hydrogen cyanate may oeeur.
特殊灭火程序：戴防护口罩。—Special Extinguishing Procedure.
废弃处置方法：依地方法规焚化处理。
Disposal information :Should be disposed of at appropriate incineration unit observing offocial local regulations.
十四、运送资料Transport infotmation
生物指标Biotic index
环已酮Cyclohexanone
个人防护设备Personal protection equipment
呼吸防护：戴防护口罩Resperatory protection:Wear air-supplid respirator
手部防护：戴手套Hand protection:Wear gloves
最重要症状及危害效应：头痛、晕眩、呕吐、困倦。Major Disease and Harn Effect:headache,dizziness,vomit and drowsiness.
对急救人员之防护：戴口罩、手套、面具、防护衣。First-Aid Protection :Wear respirator,rubber gloves,goggles and protective clothing.
物质安全资料表
九、物理及化学性质Physical and Chemical Properties /Characteristics

热熔胶

松装密度：0.48-0.52g/cm3；安息角：30-35度；
粘接强度：≥1.5-2.0kg/25mm；耐洗性：≥5次。
此类热熔胶可分为聚酰胺（PA）、聚酯（PES）、聚乙烯（LOPE和HDPE）和聚酯酰胺（PEA）等，该类胶粘剂已通过五项成果鉴定，完成国家“七五”攻关、河北省“八五”攻关项目，获国家发明奖、天津市、河北省科技成果奖各一项、获国家发明专利三项。
四、抗温。热熔胶对温度比较敏感。温度达到一定程度，热熔胶开始软化，低于一定温度，热熔胶会变脆，所以选择热熔胶必须充分考虑到产品所在环境的温度变化。
五、粘性。热熔胶的粘性分早期粘性和后期粘性。只有早期粘性和后期粘性一致，才能使热熔胶与被接着物保持稳定。在热熔胶的生产过程中，应保证其具有抗氧性、抗卤性、抗酸碱性和增塑性。被接着物材质的不同,热熔胶所发挥的粘性也有所不同，因此，应根据不同的材质选择不同的热熔胶。
3.用途广，适合粘接各种材料。
4.可以进行几次粘接，即涂在木材上热熔胶，因冷却固化而未达到要求时，可以重新加热进行二次粘接。
热熔胶是纺织品尤其是服装加工中用得最多的一类胶粘剂，被广泛用于无纺布、地毯接缝、衣料衬里、拉链等的粘接。应用于纺织工业上的热熔胶要有好的粘接强度、优异的柔软性、耐水洗/干洗。另外，由于织物在定型过程中，大多要经过蒸汽处理，因此，要求胶具有耐高温蒸汽的特性，其软化点要求高于115℃，巳要有适当的结晶度，以提高胶的热稳定性。例如，以聚酰胺为基体，其下限含量为45%(质量分数)。对于柔软性极好的纤维织物，则要求热熔胶有较低的加工粘度。
①织物粘贴用热熔胶
以粘接代缝纫可大大减轻制衣劳动强度，且制作的服装精细、合身、结实牢固。用于织物粘贴的热熔胶主要有聚酰胺、聚酪和聚氨酯等类。
②衬布加工用热熔胶

热熔胶EasyPack 100- MSDS

MSDS No XXXX. :1.0***CHEMICAL SAFETY DATA SHEET ***1. CHEMICAL PRODUCT AND COMPANY IDENTIFICA TION PRODUCT NUMBER ------------------100PRODUCT NAME --------------------Technomelt Easy-Pac TM100SYNONYM NAME --------------------HOT MEL T ADHESIVEHenkel Adhesives Technologies (Guangdong) Co. Ltd.Middle Section, 5th Industrial Estate,Nanzha, Humen, Dongguan, Guangdong,P.R.C.Post code: 523932TEL: 86-769-85563700FAX: 86-769-855680302. COMPOSITION/INFORMA TION OF INGREDIENTSCHEMICAL FAMIL Y -----------------Hot Melt AdhesiveNone hazardous.3. HAZARDS IDENTIFICA TIONNot considered as hazardous.EYE -----------------------------As supplied: irritant as a foreign body.As used: severe thermal hazard.SKIN CONTACT --------------------Exposure to hot material may cause thermalhazardINHALATION ----------------------Negligible hazard at ambient temperature.V apors and/or aerosols which may be formed atelevated temperatures may be irritating to eyesand respiratory tract.INGESTION -----------------------No hazard in normal industrial use.4. FIRST-AID MEASURESEYE -----------------------------If hot: flush with cool water. Treat as wax orresin burn. Do not attempt to remove solidifiedadhesive. Get medical attention immediately.As supplied: remove as foreign body.SKIN CONTACT --------------------For hot product, immediately immerse in orflush affected area with large amounts of coldwater to dissipate heat. Cover with clean cottonsheeting and get prompt medical attention. INHALATION ----------------------Remove to fresh air. If breathing has stopped,give artificial respiration. Get medical attention. AUTOIGNITION --------------------Unknown.FLASH POINT --------------------->260°C (Cleveland Open Cup) EXTINGUISHING MEDIA -------------CO2; Dry chemical; FoamSPECIAL FIREFIGHTING PROCEDURES -Fire fighters should be equipped withself-contained breathing apparatus to protectagainst potentially toxic and irritating fumes. FIRE & EXPLOSION HAZARDS --------Not applicable.UPPER EXPLOSION LIMIT (%) -------Not applicable.LOWER EXPLOSION LIMIT (%) -------Not applicable.NFPA FLAMMABILITY HAZARD CLASS --0 =SPILL & LEAK PROCEDURES ---------Allow to cool and solidify. Scrape up and collectin suitable containers for disposal.For safety and environmental precautions, please review entire Material Safety Data Sheet for necessary information.7. HANDLING AND STORAGESTORAGE TEMPERATURE -------------0 – 40°CHANDLING/STORAGE ----------------Store in a cool, dry area.Precaution: this product should only be heated torecommended temperatures. Hazards ofpyrolysis products emitted are unknown andmay be hazardous to health.VENTILA TION REQUIREMENTS --------Local; general8. EXPOSURE CONTROLS/PERSONAL PROTECTIONVENTILA TION REQUIREMENTS --------Local; generalEYE PROTECTION REQUIREMENTS -----Avoid contact with eyes. Wear chemical gogglesif there is likelihood of contact with eyes. GLOVE REQUIREMENTS --------------Thermally resistant gloves should be worn. CLOTHING REQUIREMENTS -----------Employee must wear appropriate protectiveclothing and equipment to prevent anypossibility of skin contact with this substance. CHANGE/REMOV AL OF CLOTHING ------Not required unless molten adhesive has beensplashed on clothing and passes through fabric.WASH REQUIREMENTS ---------------None.RESPIRATOR REQUIREMENTS ---------Avoid prolonged or repeated breathing of vaporor mists. If exposure may or does exceedoccupational exposure limits, use a NIOSHapproved respirator to prevent overexposure.9. PHYSICAL AND CHEMICAL PROPERTIESPURE SUBSTANCE OR MIXTURE -------MixturePHYSICAL FORM -------------------SolidAPPEARANCE/ODOR -----------------Pale Yellow solid; Negligible odorODOR THRESHOLD ------------------Not availablePH AS IS ------------------------N/A (not applicable)PH IN (1%) SOLUTION -------------N/ABOILING POINT ------------------->260°CMEL TING/FREEZING POINT ----------N/ASOLUBILITY IN WATER -------------InsolublePARTITION COEFFICIENT(N-octanol/water) -------------N/ASPECIFIC GRA VITY (WA TER=1) ------0.97EV APORATION RATE ----------------Nil (water)V APOR PRESSURE (mmHg) -----------Nil (20°C)V APOR DENSITY (air=1) -----------NilVOLA TILES -----------------------NilVOLA TILE ORGANIC COMPOUNDS ------ NilAUTOIGNITION --------------------UnknownFLASH POINT --------------------->260°C (Cleveland Open Cup)OXIDIZING PROPERTIES ------------N/A10. STABILITY AND REACTIVITYSTABILITY -----------------------StableNFPA REACTIVITY HAZARD CLASS ---- 0 = InsignificantHAZARDOUS DECOMPOSITIONPRODUCTSCarbon monoxide, carbon dioxide-------------------------------11. TOXICOLOGICAL INFORMA TIONCHRONIC (LONG TERM) EFFECTS OF EXPOSUREROUTE OF ENTRY ------------------Skin contact; Eye contact.EFFECTS OF CHRONIC EXPOSURE -----The toxicological properties of this product havenot been fully evaluated. Use of good industrialhygiene practices is required. Avoid directcontact with skin or eyes. Do not ingest orinhale.TARGET ORGANS -------------------Not applicable.CARCINOGEN ----------------------No.12. ECOLOGICAL INFORMATIONNot Available.13. DISPOSAL CONSIDERA TIONSWASTE DISPOSAL METHODS ----------Waste disposal should be in accordance withexisting federal, state and local environmentalregulations.EMPTY CONTAINER WARNINGS --------Empty containers may contain product residue;follow CSDS and label warnings even after theyhave been emptied.14. TRANSPORTA TION INFORMA TIONDOT INFORMATION:DOT SHIPPING NAME ---------------ADHESIVE no. 1DOT HAZARD CLASS ----------------Non hazardousDOT REPORTABLE QUANTITY ---------Not noted15. REGULA TORY INFORMA TIONFDA -----------------------------21CFR175.10516. OTHER INFORMA TIONISSUE DATE -----------------------2008/03/07FOR INFORMATION CONTACT ---------Henkel Adhesives Technologies (Guangdong)Co. Ltd.Middle Section, 5th Industrial Estate,Nanzha, Humen, Dongguan, Guangdong,R.P.C.Post code: 523932Contact person: Jimm QiuTitle: Technical ManagerTEL: 86-769-85563700FAX: 86-769-85568030*** ADDITIONAL INFORMATION ***The information given and the recommendations made herein apply to our product(s) alone and are not combined with other product(s). Such are based on our research and on data from other reliable sources and are believed to be accurate. No guaranty of accuracy is made. It is the purchaser’s responsibility before using any product to verify this data under their own operating conditions and to determine whether the product is suitable for their purposes.。

MSDS—热溶胶

成份名称百分比% 乙烯-醋酸共聚树脂 70%
成份名称氢基丙烯酸乙
百分比% 80%
单位指标公斤 7kg 乙烯-醋酸共聚树脂
检验结果 OK
操作注意事项
在通风环境下操作
储存注意事项
阴凉干ቤተ መጻሕፍቲ ባይዱ下储存
十、接触控制/个体防护职业接触限值（MG/M³) 工程控制眼睛防护手防护其它防护十一、理化特征外观比重（g/m3) 不挥发度主要用途十二、稳定性稳定性禁配物十三、毒理学资料急性毒性慢性毒性致癌性刺激性十四、废气处理废气注意事项废气处理方法十五、运输信息包装类别运输注意事项纸箱包装、胶瓶胶水在运输过程中切勿倒放。无无无无无无良好 / 透明 / / 适用ABS，PVC等塑胶 / / 护眼罩护胶套 /
十六、法规信息
法规信息
『物质安全资料表MSDS』
一、制造商或供应资料制造商/供应商名称制造商/供应商地址联系人及电话号码二、物品名称物品名称物品英文名称三、产品成份资料产品主要成份及百分比四、技术指标项目内压力有效成份五、危险性概述危险性类别侵入途径健康危害环境危害燃爆危险六、急救措施皮肤接触眼睛接触吸入食入七、消防措施危险性灭火方法八、泄漏应急处理泄漏处理九、操作处理与储存固化后铲除低灭火器用热水或丙酮洗耳恭听涤，将皮肤慢慢拉开。用水充分冲洗 / / 低无无无无热熔胶瞬间胶水深圳市恒利实业有限公司龙货第四工业区黄种基 28130992 共2页第一页

5-热熔胶粉MSDS

废弃处置方法：依地方法规焚化处理。
Disposal information :Should be disposed of at appropriate incineration unit observing offocial local regulations.
十四、运送资料Transport infotmation
最重要症状及危害效应：头痛、晕眩、呕吐、困倦。Major Disease and Harn Effect:headache,dizziness,vomit and drowsiness.
对急救人员之防护：戴口罩、手套、面具、防护衣。First-Aid Protection :Wear respirator,rubber gloves,goggles and protective clothing.
分解温度Decomposition tenperature
闪火点：— -F -4℃Flash point
测试方法：开杯闭杯Test method:Open up ane Closed cup
自然温度Spontaneous temperature
爆炸界限Explosion limits:
蒸气压Vapor pressure：
眼睛接触Eye Contact：用大量水冲洗再送医治疗。Rinse with plenty of water ,then genmedical assistance immediately.
食入Ingestion：避免催吐并送医治疗。Avoid vomitting and seed medical advice.
急毒性：呼吸困难Aeule toxieity:Breathe hardly
局部效应：Local Effeets

MSDS-06热熔胶

第五部分：消防措施
危险特性：粉体与空气可形成爆炸性混合物, 当达到一定浓度时, 遇火星会发生爆炸。加热分解产生易燃气体。
有害燃烧产物：一氧化碳、二氧化碳。
灭火方法：消防人员须佩戴防毒面具、穿全身消防服，在上风向灭火。灭火剂：雾状水、泡沫、干粉、二氧化碳、砂土。
第六部分：泄漏应急处理
应急处理：隔离泄漏污染区，限制出入。切断火源。建议应急处理人员戴防尘面具（全面罩），穿防毒服。避免扬尘，小心扫起，置于袋中转移至安全场所。若大量泄漏，收集回收或运至废物处理场所处置。
第十五部分：法规信息
法规信息：化学危险物品安全管理条例 (1987年2月17日国务院发布)，化学危险物品安全管理条例实施细则 (化劳发[1992] 677号)，工作场所安全使用化学品规定 ([1996]劳部发423号)等法规，针对化学危险品的安全使用、生产、储存、运输、装卸等方面均作了相应规定。
第十六部分：其他信息
无资料
化学品名称：热熔胶编号：MSDS--06
第一部分：化学品名称
化学品中文名称：乙烯-醋酸乙烯共聚物化学品英文名称：ethylene-vinyl acetate copolymer
中文名称2：英文名称2：EVA
CAS No.：24937-78-8
第二部分：成分/组成信息
有害物成分含量 CAS No.
乙烯-醋酸乙烯共聚物100%24937-78-8
废弃物性质：无资料
废弃处置方法：处置前应参阅国家和地方有关法规。建议用焚烧法处置。
废弃注意事项：无资料
第十四部分：运输信息
危险货物编号：无资料UN编号：无资料包装标志：无资料包装类别：Z01
包装方法：无资料。
运输注意事项：起运时包装要完整，装载应稳妥。运输过程中要确保容器不泄漏、不倒塌、不坠落、不损坏。严禁与氧化剂、碱类、食用化学品等混装混运。运输途中应防曝晒、雨淋，防高温。车辆运输完毕应进行彻底清扫。

3M3779Q热熔胶条 MSDS

zhou:153-38028-741Material Safety Data SheetCopyright, 2006, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.SECTION 1: PRODUCT AND COMPANY IDENTIFICATIONPRODUCT NAME: 3M(TM) Scotch-Weld (TM) Hot Melt Adhesive 3779-AE / 3779-PG / 3779-TC / 3779-Q/3779-BMANUFACTURER: 3MDIVISION: Industrial Adhesives and TapesADDRESS: 3M CenterSt. Paul, MN 55144-1000EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)Issue Date: 03/06/2006Supercedes Date: 11/21/2002Document Group: 10-0384-7Product Use:Specific Use:hot melt adhesiveSECTION 2: INGREDIENTSIngredient C.A.S. No.% by WtPOLYAMIDE POLYMER Trade Secret 100SECTION 3: HAZARDS IDENTIFICATION3.1 EMERGENCY OVERVIEWSpecific Physical Form: Waxy SolidOdor, Color, Grade: dark amber, odorless (molten state - pungent resinous odor), solid adhesive in rods.General Physical Form: SolidImmediate health, physical, and environmental hazards: May cause thermal burns.3.2 POTENTIAL HEALTH EFFECTSEye Contact:Vapors from heated material may cause eye irritation. Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.Thermal Burns: Signs/symptoms may include severe pain, redness and swelling, and tissue destruction.Skin Contact:Thermal Burns: Signs/symptoms may include intense pain, redness and swelling, and tissue destruction.Inhalation:Vapors from heated material may cause irritation of the respiratory system. Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain.Ingestion:Physical Blockage: Signs/symptoms may include cramping, abdominal pain, and constipation.SECTION 4: FIRST AID MEASURES4.1 FIRST AID PROCEDURESThe following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed.Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes. DO NOT ATTEMPT TO REMOVE MOLTEN MATERIAL. Get immediate medical attention.Skin Contact: Immediately flush skin with large amounts of cold water for at least 15 minutes. DO NOT ATTEMPT TO REMOVE MOLTEN MATERIAL. Cover affected area with a clean dressing. Get immediate medical attention.Inhalation: If signs/symptoms develop, remove person to fresh air. If signs/symptoms persist, get medical attention.If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get medical attention.SECTION 5: FIRE FIGHTING MEASURES5.1 FLAMMABLE PROPERTIESFlash Point 550 ºF [Test Method: Cleveland Open Cup] [Details:CONDITIONS: ASTM D-92-72]5.2 EXTINGUISHING MEDIAOrdinary combustible material. Use fire extinguishers with class A extinguishing agents (e.g., water, foam).5.3 PROTECTION OF FIRE FIGHTERSSpecial Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA).Unusual Fire and Explosion Hazards: Not applicable.Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition information.SECTION 6: ACCIDENTAL RELEASE MEASURESAccidental Release Measures: Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by qualified personnel. Reclaim undamaged product. Collect as much of the spilled material as possible. Dispose of collected material as soon as possible.In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations.SECTION 7: HANDLING AND STORAGE7.1 HANDLINGAvoid skin contact with hot material. Keep out of the reach of children.7.2 STORAGEStore away from heat. Store out of direct sunlight.SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION8.1 ENGINEERING CONTROLSNot applicable. Use in a well-ventilated area.8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)8.2.1 Eye/Face ProtectionAvoid eye contact.The following eye protection(s) are recommended: Safety Glasses with side shields, Indirect Vented Goggles.8.2.2 Skin ProtectionWear appropriate gloves, such as Nomex, when handling this material to prevent thermal burns. Avoid skin contact with hot material.8.2.3 Respiratory ProtectionUnder normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.8.2.4 Prevention of SwallowingDo not ingest.8.3 EXPOSURE GUIDELINESNone EstablishedSECTION 9: PHYSICAL AND CHEMICAL PROPERTIESSpecific Physical Form: Waxy SolidOdor, Color, Grade: dark amber, odorless (molten state - pungent resinous odor), solidadhesive in rods.General Physical Form: SolidFlash Point 550 ºF [Test Method: Cleveland Open Cup] [Details:CONDITIONS: ASTM D-92-72]Boiling point Not ApplicableDensity 0.99 g/cm3Vapor Density NilVapor Pressure NilSpecific Gravity 0.99 [Ref Std: WATER=1]pH Not ApplicableMelting point Not ApplicableSolubility in Water NilEvaporation rate Not ApplicableVolatile Organic Compounds Not ApplicablePercent volatile 0 % weightVOC Less H2O & Exempt Solvents Not ApplicableViscosity Not ApplicableSECTION 10: STABILITY AND REACTIVITYStability: Stable.Materials and Conditions to Avoid: HeatHazardous Polymerization: Hazardous polymerization will not occur.Hazardous Decomposition or By-ProductsSubstance ConditionAmine Compounds During CombustionCarbon monoxide During CombustionCarbon dioxide During CombustionSECTION 11: TOXICOLOGICAL INFORMATIONPlease contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or itscomponents.SECTION 12: ECOLOGICAL INFORMATIONECOTOXICOLOGICAL INFORMATIONNot determined.CHEMICAL FATE INFORMATIONNot determined.SECTION 13: DISPOSAL CONSIDERATIONSWaste Disposal Method: Reclaim if feasible. If product can't be reclaimed, dispose of waste product in a sanitary landfill. Alternatively, incinerate the waste product in an industrial, commercial, or municipal incinerator. As a disposal alternative, incinerate in an industrial or commercial facility.Since regulations vary, consult applicable regulations or authorities before disposal.SECTION 14:TRANSPORT INFORMATIONID Number(s):62-3779-7230-2, 62-3779-7231-0, 62-3779-7232-8, 62-3779-7233-6, 62-3779-7234-4, 62-3779-7235-1, 62-3779-7236-9, 62-3779-9030-4, 62-3779-9130-2, 62-3779-9132-8, 62-3779-9136-9, 62-3779-9330-8, 62-3779-9335-7, 62-3779-9336-5, 62-3779-9337-3, 62-3779-9530-3, 62-3779-9531-1, 62-3779-9830-7, 62-3779-9836-4, 62-3779-9930-5Not regulated per U.S. DOT, IATA or IMO.These transportation classifications are provided as a customer service. As the shipper YOU remain responsible forcomplying with all applicable laws and regulations, including proper transportation classification and packaging. 3M's transportation classifications are based on product formulation, packaging, 3M policies and 3M's understanding of applicable current regulations. 3M does not guarantee the accuracy of this classification information. This information applies only to transportation classification and not the packaging, labeling, or marking requirements. The original 3M package is certified for U.S. ground shipment only. If you are shipping by air or ocean, the package may not meet applicable regulatoryrequirements.SECTION 15: REGULATORY INFORMATIONUS FEDERAL REGULATIONSContact 3M for more information.311/312 Hazard Categories:Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - NoSTATE REGULATIONSContact 3M for more information.CHEMICAL INVENTORIESThe components of this product are in compliance with the chemical notification requirements of TSCA.All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS), or are exempt polymers whose monomers are listed on EINECS.Contact 3M for more information.INTERNATIONAL REGULATIONSContact 3M for more information.This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.SECTION 16: OTHER INFORMATIONNFPA Hazard ClassificationHealth: 1 Flammability: 1 Reactivity: 0 Special Hazards: NoneNational Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.Revision Changes:Section 1: Product name was modified.Section 16: NFPA hazard classification heading was modified.Section 16: NFPA hazard classification for health was modified.Section 1: Division name was modified.Copyright was modified.Section 5: Fire fighting procedures information was modified.Section 6: Release measures information was modified.Section 8: Engineering controls information was modified.Section 8: Skin protection phrase was modified.Section 13: Waste disposal method information was modified.Section 15: 311/312 hazard categories heading was modified.Section 15: International regulations information was modified.Section 15: State regulations information was modified.Section 15: US federal regulations information was modified.Section 4: First aid for inhalation - termination of exposure - was modified.Section 4: First aid for inhalation - medical assistance - was modified.Section 10: Hazardous polymerization heading was modified.Section 14: Transportation legal text was modified.Section 2: Ingredient table was modified.Section 16: NFPA explanation was modified.Page Heading: Product name was modified.Section 15: Inventories information was modified.Section 12: Ecotoxicological information heading was modified.Section 12: Chemical fate information heading was modified.Section 16: NFPA hazard classification for special hazards was modified.Section 8: Exposure guidelines information - none - was modified.Section 12: Ecotoxicological phrase was modified.Section 12: Chemical Fate phrase was modified.Section 2: Ingredient phrase was added.DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application.3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.3M MSDSs are available at 。

热熔胶MSDS英文版

PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS1 CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONPRODUCTProduct Name: HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSProduct Description: HOT MELT ADHESIVE,MIXTUREProduct Code:Intended Use: ADHESIVE,FOR AUTOMOBILE LAMPSCOMPANY IDENTIFICATIONHuangshan Xiuning Xindecheng Chemical Co., Ltd.SUPPLIER:Wanning Industrial Park, Huangshan, Anhui, China (245400)Telephone: 0086-559-7519970Facsimile: 0086-559-7519971This (M)SDS is a generic document with no country specific information included.2 COMPOSITION/INFORMATION ON INGREDIENTSNo Reportable Hazardous Substance(s) or Complex Substance(s).INGREDIENTS CAS No.Approx. Proportionstyrene butadiene rubber9003-55-8Med 50-60%rosin resin8050-09-7Low 50-40%PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS3 HAZARDS IDENTIFICATIONThis material is not considered to be hazardous.PHYSICAL / CHEMICAL HAZARDSN/AHEALTH HAZARDSNo adverse effects due to inhalation are expected. When heated, the vapour/fumes given off may cause respiratory tract irritation.4 FIRST AID MEASURESINHALATIONIn case of adverse exposure to vapors and / or aerosols formed at elevated temperatures, immediately remove the affected victim from exposure. Administer artificial respiration if breathing is stopped. Keep at rest.SKIN CONTACTWash contact areas with soap and water. For hot product: Immediately immerse in or flush affected area with large amounts of cold water to dissipate heat. Cover with clean cotton sheeting or gauze and get prompt medical attention.EYE CONTACTFlush thoroughly with water. If irritation occurs, get medical assistance.INGESTIONFirst aid is normally not required. Seek medical attention if discomfort occurs.5 FIRE- FIGHTING MEASURESPRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSEXTINGUISHING MEDIAAppropriate Extinguishing Media: Use dry chemical or carbon dioxide (CO2) to extinguish flames.Inappropriate Extinguishing Media: Straight streams of waterFIRE FIGHTINGFire Fighting Instructions: Assure an extended cooling down period to prevent re-ignition. Evacuate area. Prevent run-off from fire control or dilution from entering streams, sewers or drinking water supply.Hazardous Combustion Products: Flammable hydrocarbons, Oxides of carbon, Smoke, Fume, Incompletecombustion products6 ACCIDENTAL RELEASE MEASURESNOTIFICATION PROCEDURESIn the event of a spill or accidental release, notify relevant authorities in accordance with all applicable regulations.ENVIRONMENTAL PRECAUTIONSN/A7 HANDLING AND STORAGEHANDLINGAvoid elevated temperatures for prolonged periods of time. Protect material from direct sunlight. Material canaccumulate static charges which may cause an electrical spark (ignition source). Apart from the specific nature of the polymer product, conditions such as humidity, sunlight and temperature.Loading/Unloading Temperature: [Ambient]Transport Temperature: [Ambient]PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSSTORAGEStore in a cool, dry place.Storage Temperature: 0℃—40℃Storage Pressure:[Ambient]8 EXPOSURE CONTROLS /PERSONAL PROTECTIONENGINEERING CONTROLSN/APERSONAL PROTECTIONPersonal protective equipment selections vary based on potential exposure conditions such as applications, handling practices, concentration and ventilation. Information on the selection of protective equipment for use with this material, as provided below, is based upon intended, normal usage.Respiratory Protection:If engineering controls do not maintain airborne contaminant concentrations at a level which is adequate to protect worker health, an approved respirator may be appropriate. Respirator selection, use, and maintenance must be in accordance with regulatory requirements, if applicable. Types of respirators to be considered for this material include:No special requirements under ordinary conditions of use and with adequate ventilation.For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode.Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate, gas/vapour warning properties are poor, or if air purifying filter capacity/rating may be exceeded.Hand Protection:If product is hot, thermally protective gloves are recommended. If contact with forearms is likely, wear gauntlet style gloves.PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSEye Protection:If contact is likely, safety glasses with side shields are recommended.Skin and Body Protection:If product is hot, thermally protective, chemical resistant apron and long sleeves are recommended.Specific Hygiene Measures:Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned. Practice good housekeeping.9 PHYSICAL AND CHEMICAL PROPERTIESTypical physical and chemical properties are given below. Consult the Supplier in Section 1 for additional data. GENERAL INFORMATIONPhysical State: SolidForm: GrainsColour: GrayOdour: None to MildIMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATIONRelative Density (at 18 C): 0.97Density (at 18 ºC): 970 kg/m³Flash Point [method]: O.C Cleveland Open Cup ＞260℃Flammable Limits (Approximate volume % in air): LEL: N/D UEL: N/DAutoignition Temperature: N/APRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSBoiling Point / Range: ＞260℃Vapour Density (Air = 1): N/AVapour Pressure: N/AEvaporation Rate (N-Butyl Acetate = 1): N/ApH: N/ALog Pow (n-Octanol/Water Partition Coefficient): N/ASolubility in Water: Negligible10 STABILITY AND REACTIVITYSTABILITY:Material is stable under normal conditions.CONDITIONS TO AVOID:Avoid elevated temperatures for prolonged periods of time.HAZARDOUS DECOMPOSITION PRODUCTS:Material does not decompose at ambient temperatures. HAZARDOUS POLYMERIZATION:Will not occur.11 TOXICOLOGICAL INFORMATIONPRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSAcute ToxicityRoute of Exposure Conclusion / RemarksINHALATIONToxicity: Minimally Toxic. Based on test data for structurally similarmaterials.Irritation: Negligible hazard at ambient/normal handling temperatures. Basedon test data for structurally similar materials.INGESTIONToxicity: Minimally Toxic. Based on test data for structurally similarmaterials.SkinToxicity: Minimally Toxic. Based on test data for structurally similarmaterials.Irritation: Negligible irritation to skin at ambient temperatures. Based on testdata for structurally similar materials.EyeIrritation: May cause mild, short-lasting discomfort to eyes. Based on testdata for structurally similar materials.CHRONIC/OTHER EFFECTS12 ECOLOGICAL INFORMATIONThe information given is based on data available for the material, the components of the material, and similar materials. ECOTOXICITYPRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSMaterial -- Not expected to be harmful to aquatic organisms.Material -- Not expected to be harmful to terrestrial organisms13 DISPOSAL CONSIDERATIONSDisposal recommendations based on material as supplied. Disposal must be in accordance with current applicable laws and regulations, and material characteristics at time of disposal.DISPOSAL RECOMMENDATIONSSuitable routes of disposal are supervised incineration, preferentially with energy recovery, or appropriate recycling methods in accordance with applicable regulations and material characteristics at the time of disposal.14 TRANSPORT INFORMATIONLAND : Not Regulated for Land TransportSEA (IMDG) : Not Regulated for Sea Transport according to IMDG-CodeAIR (IATA) : Not Regulated for Air Transport15 RRGULATORY INFORMATIONPRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSMaterial is not hazardous as defined by the EU Dangerous Substances/Preparations Directives.16 OTHER INFORMATIONN/D = Not determined, N/A = Not applicableTHIS SDS COVERS THE FOLLOWING MATERIALS: Petroleum hydrocarbon resin ECR 807 | Escorez 2203 LC | mixed resin dust-----------------------------------------------------------------------------------------------------------------------------------------------------The information and recommendations contained herein are, to the best of Xindecheng’s knowledge and belief, accurate and reliable as of the date issued. You can contact Xindecheng to insure that this document is the most current available from Jinsen. The information and recommendations are offered for the user's consideration and examination. It is the user's responsibility to satisfy itself that the product is suitable for the intended use. If buyer repackages this product, it is the user's responsibility to insure proper health, safety and other necessary information is included with and/or on the container. Appropriate warnings and safe-handling procedures should be provided to handlers and users. Alteration of this document is strictly prohibited.---------------------------------------------------------------------------------------------------------------------------。

化学品安全数据表MSDS-06热熔胶

废弃物性质：无资料
废弃处置方法：处置前应参阅国家和地方有关法规。建议用焚烧法处置。
废弃注意事项：无资料
第十四部分：运输信息
危险货物编号：无资料UN编号：无资料包装标志：无资料包装类别：Z01
包装方法：无资料。
运输注意事项：起运时包装要完整，装载应稳妥。运输过程中要确保容器不泄漏、不倒塌、不坠落、不损坏。严禁与氧化剂、碱类、食用化学品等混装混运。运输途中应防曝晒、雨淋，防高温。车辆运输完毕应进行彻底清扫。
主要成分：纯品外观与性状：pH：熔点(℃)：无资料沸点(℃)：无资料
相对密度(水=1)：无资料相对蒸气密度(空气=1)：无资料饱和蒸气压(kPa)：无资料
燃烧热(kJ/mol)：无资料临界温度(℃)：无资料临界压力(MPa)：无资料
辛醇/水分配系数的对数值：无资料闪点(℃)：无资料引燃温度(℃)：无资料
第七部分：操作处置与储存
操作注意事项：密闭操作。密闭操作，提供良好的自然通风条件。操作人员必须经过专门培训，严格遵守操作规程。建议操作人员佩戴自吸过滤式防尘口罩，戴化学安全防护眼镜，穿防毒物渗透工作服，戴橡胶手套。远离火种、热源，工作场所严禁吸烟。使用防爆型的通风系统和设备。避免产生粉尘。避免与氧化剂、碱类接触。搬运时要轻装轻卸，防止包装及容器损坏。配备相应品种和数量的消防器材及泄漏应急处理设备。倒空的容器可能残留有害物。
第五部分：消防措施
危险特性：粉体与空气可形成爆炸性混合物, 当达到一定浓度时, 遇火星会发生爆炸。加热分解产生易燃气体。
有害燃烧产物：一氧化碳、二氧化碳。
灭火方法：消防人员须佩戴防毒面具、穿全身消防服，在上风向灭火。灭火剂：雾状水、泡沫、干粉、二氧化碳、砂土。
第六部分：泄漏应急处理
应急处理：隔离泄漏污染区，限制出入。切断火源。建议应急处理人员戴防尘面具（全面罩），穿防毒服。避免扬尘，小心扫起，置于袋中转移至安全场所。若大量泄漏，收集回收或运至废物处理场所处置。

热熔胶MSDS英文版

PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS1 CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONPRODUCTProduct Name: HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSProduct Description: HOT MELT ADHESIVE,MIXTUREProduct Code:Intended Use: ADHESIVE,FOR AUTOMOBILE LAMPSCOMPANY IDENTIFICATIONHuangshan Xiuning Xindecheng Chemical Co., Ltd.SUPPLIER:Wanning Industrial Park, Huangshan, Anhui, China (245400)Telephone: 0086-559-7519970Facsimile: 0086-559-7519971This (M)SDS is a generic document with no country specific information included.2 COMPOSITION/INFORMATION ON INGREDIENTSNo Reportable Hazardous Substance(s) or Complex Substance(s).INGREDIENTS CAS No.Approx. Proportionstyrene butadiene rubber9003-55-8Med 50-60%rosin resin8050-09-7Low 50-40%PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS3 HAZARDS IDENTIFICATIONThis material is not considered to be hazardous.PHYSICAL / CHEMICAL HAZARDSN/AHEALTH HAZARDSNo adverse effects due to inhalation are expected. When heated, the vapour/fumes given off may cause respiratory tract irritation.4 FIRST AID MEASURESINHALATIONIn case of adverse exposure to vapors and / or aerosols formed at elevated temperatures, immediately remove the affected victim from exposure. Administer artificial respiration if breathing is stopped. Keep at rest.SKIN CONTACTWash contact areas with soap and water. For hot product: Immediately immerse in or flush affected area with large amounts of cold water to dissipate heat. Cover with clean cotton sheeting or gauze and get prompt medical attention.EYE CONTACTFlush thoroughly with water. If irritation occurs, get medical assistance.INGESTIONFirst aid is normally not required. Seek medical attention if discomfort occurs.5 FIRE- FIGHTING MEASURESPRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSEXTINGUISHING MEDIAAppropriate Extinguishing Media: Use dry chemical or carbon dioxide (CO2) to extinguish flames.Inappropriate Extinguishing Media: Straight streams of waterFIRE FIGHTINGFire Fighting Instructions: Assure an extended cooling down period to prevent re-ignition. Evacuate area. Prevent run-off from fire control or dilution from entering streams, sewers or drinking water supply.Hazardous Combustion Products: Flammable hydrocarbons, Oxides of carbon, Smoke, Fume, Incompletecombustion products6 ACCIDENTAL RELEASE MEASURESNOTIFICATION PROCEDURESIn the event of a spill or accidental release, notify relevant authorities in accordance with all applicable regulations.ENVIRONMENTAL PRECAUTIONSN/A7 HANDLING AND STORAGEHANDLINGAvoid elevated temperatures for prolonged periods of time. Protect material from direct sunlight. Material canaccumulate static charges which may cause an electrical spark (ignition source). Apart from the specific nature of the polymer product, conditions such as humidity, sunlight and temperature.Loading/Unloading Temperature: [Ambient]Transport Temperature: [Ambient]PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSSTORAGEStore in a cool, dry place.Storage Temperature: 0℃—40℃Storage Pressure:[Ambient]8 EXPOSURE CONTROLS /PERSONAL PROTECTIONENGINEERING CONTROLSN/APERSONAL PROTECTIONPersonal protective equipment selections vary based on potential exposure conditions such as applications, handling practices, concentration and ventilation. Information on the selection of protective equipment for use with this material, as provided below, is based upon intended, normal usage.Respiratory Protection:If engineering controls do not maintain airborne contaminant concentrations at a level which is adequate to protect worker health, an approved respirator may be appropriate. Respirator selection, use, and maintenance must be in accordance with regulatory requirements, if applicable. Types of respirators to be considered for this material include:No special requirements under ordinary conditions of use and with adequate ventilation.For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode.Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate, gas/vapour warning properties are poor, or if air purifying filter capacity/rating may be exceeded.Hand Protection:If product is hot, thermally protective gloves are recommended. If contact with forearms is likely, wear gauntlet style gloves.PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSEye Protection:If contact is likely, safety glasses with side shields are recommended.Skin and Body Protection:If product is hot, thermally protective, chemical resistant apron and long sleeves are recommended.Specific Hygiene Measures:Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned. Practice good housekeeping.9 PHYSICAL AND CHEMICAL PROPERTIESTypical physical and chemical properties are given below. Consult the Supplier in Section 1 for additional data. GENERAL INFORMATIONPhysical State: SolidForm: GrainsColour: GrayOdour: None to MildIMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATIONRelative Density (at 18 C): 0.97Density (at 18 ºC): 970 kg/m³Flash Point [method]: O.C Cleveland Open Cup ＞260℃Flammable Limits (Approximate volume % in air): LEL: N/D UEL: N/DAutoignition Temperature: N/APRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSBoiling Point / Range: ＞260℃Vapour Density (Air = 1): N/AVapour Pressure: N/AEvaporation Rate (N-Butyl Acetate = 1): N/ApH: N/ALog Pow (n-Octanol/Water Partition Coefficient): N/ASolubility in Water: Negligible10 STABILITY AND REACTIVITYSTABILITY:Material is stable under normal conditions.CONDITIONS TO AVOID:Avoid elevated temperatures for prolonged periods of time.HAZARDOUS DECOMPOSITION PRODUCTS:Material does not decompose at ambient temperatures. HAZARDOUS POLYMERIZATION:Will not occur.11 TOXICOLOGICAL INFORMATIONPRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSAcute ToxicityRoute of Exposure Conclusion / RemarksINHALATIONToxicity: Minimally Toxic. Based on test data for structurally similarmaterials.Irritation: Negligible hazard at ambient/normal handling temperatures. Basedon test data for structurally similar materials.INGESTIONToxicity: Minimally Toxic. Based on test data for structurally similarmaterials.SkinToxicity: Minimally Toxic. Based on test data for structurally similarmaterials.Irritation: Negligible irritation to skin at ambient temperatures. Based on testdata for structurally similar materials.EyeIrritation: May cause mild, short-lasting discomfort to eyes. Based on testdata for structurally similar materials.CHRONIC/OTHER EFFECTS12 ECOLOGICAL INFORMATIONThe information given is based on data available for the material, the components of the material, and similar materials. ECOTOXICITYPRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSMaterial -- Not expected to be harmful to aquatic organisms.Material -- Not expected to be harmful to terrestrial organisms13 DISPOSAL CONSIDERATIONSDisposal recommendations based on material as supplied. Disposal must be in accordance with current applicable laws and regulations, and material characteristics at time of disposal.DISPOSAL RECOMMENDATIONSSuitable routes of disposal are supervised incineration, preferentially with energy recovery, or appropriate recycling methods in accordance with applicable regulations and material characteristics at the time of disposal.14 TRANSPORT INFORMATIONLAND : Not Regulated for Land TransportSEA (IMDG) : Not Regulated for Sea Transport according to IMDG-CodeAIR (IATA) : Not Regulated for Air Transport15 RRGULATORY INFORMATIONPRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSMaterial is not hazardous as defined by the EU Dangerous Substances/Preparations Directives.16 OTHER INFORMATIONN/D = Not determined, N/A = Not applicableTHIS SDS COVERS THE FOLLOWING MATERIALS: Petroleum hydrocarbon resin ECR 807 | Escorez 2203 LC | mixed resin dust-----------------------------------------------------------------------------------------------------------------------------------------------------The information and recommendations contained herein are, to the best of Xindecheng’s knowledge and belief, accurate and reliable as of the date issued. You can contact Xindecheng to insure that this document is the most current available from Jinsen. The information and recommendations are offered for the user's consideration and examination. It is the user's responsibility to satisfy itself that the product is suitable for the intended use. If buyer repackages this product, it is the user's responsibility to insure proper health, safety and other necessary information is included with and/or on the container. Appropriate warnings and safe-handling procedures should be provided to handlers and users. Alteration of this document is strictly prohibited.---------------------------------------------------------------------------------------------------------------------------。

MSDS-热熔胶

（2）盛装热熔胶的容器及预热槽须盖紧，以防污染。
（3）在正确操作指导书的情况下无危害。
（4）建议“先进—先用”循环使用。
急救措施
皮肤接触：用大量清水冲洗进行冷却。严重者需要立即送医院就医。
眼睛接触：用大量清水冲洗进行冲洗，并且立即送医院就医。
吸入：应速带离现场，至空气清新处。保持环境通风。
食入：立即就医。
爆炸或泄漏的应急处理
（1）避免眼睛与皮肤接触该化学品；
（2）在工作时，操作员要佩戴防护手套；
（3）在工作时，操作员要佩戴护目镜；
（4）在工作时，操作员严禁喝水和进食；
（5）工作前和工作后，操作员要洗手。
储运注意事项
（1）保持良好的通风。
（2）储存于干爽场所。
防护
措施
车间卫生标准：/
检测方法பைடு நூலகம்/
呼吸系统防护：有效抽风系统或佩戴防毒口罩。
无
制作单位
名称：/
地址：/
电话：/
特殊说明：以上资料是根据供货商提供的资料整理而成。保存期：5年。
理化特性
物理状态：固体
颜色：白
气味：刺激气味
PH值：/
熔点：77℃--87℃
沸点：> 220℃
饱和蒸汽压（kpa）：20℃时<0.1mbar
相对密度（水=1）：20℃时1.0g/cm3
溶解：20℃时不溶于水。
粘性：160℃时4400-6000Mpa
灭火方法：泡沫、二氧化碳、干粉。
对消防人员要求：必须佩防护装备。
眼睛防护：/
身体防护：/
手防护：用手直接接触时佩戴PE防毒手套。
其它：工作中禁止吃东西，工作前后需洗手。
稳定性和反应活性

EVA热熔胶安全技术性能数据MSDS.pdf

EVA热熔胶安全技术性能数据(MSDS)组成与性状主要成分：EVA 、松香改性树脂外观与形状：乳白色颗粒主要用途：书籍订装用健康危害1、由于在使用热熔胶施工时必须加热，因此应戴劳保手套、扎好袖。

2、盛装热熔胶的容器及预热槽必须盖紧，以防污染。

3、在正确操作的情况下对人体没有危害。

4、建议按“先进先用”的顺序使用。

急救措施皮肤接触：用大量清水冲洗、冷却，严重者需要立即送医院就医眼睛接触：用大量清水冲洗，并立即送医院就医。

吸入：应迅速带离现场，至空气清新处，保持环境通风。

食入：立即就医。

理化特性物理状态：固体颜色：乳白气味：无刺激气味PH值：/软化点：77℃--87℃沸点：>220℃饱和蒸汽压(kpa)：20℃时<0.1mbar 相对密度(水=1)：20℃时1.0g/cm3溶解：20℃时不溶于水粘性：160℃时4400-6000Mpa 灭火方法：泡沫、二氧化碳、干粉。

消防人员必须佩戴防护装备。

爆炸或泄漏的应急处理1.避免眼睛、皮肤接触该化学品； 2.在工作时，应急处置人员要佩戴防护手套，严禁喝水和进食； 3.工作前和工作后，应急处置人员要洗手。

储运注意事项1.保持良好的通风；2.储存于干爽场所。

防护措施车间卫生标准：/呼吸系统防护：有效抽风系统眼睛防护：/其它：工作中禁止吃东西，工作前后需洗手稳定性和反应活性避免接触的条件：/禁忌物：无燃烧(分解)产物：高温时产生醋酸。

毒理学资料急性毒性：无亚急性和慢性毒性：无LD50：/废弃1.将空容器或未用的产品返回给供应商； 2.不可自行扔掉空容器或未用的产品；3.不能空置于水沟和地表水法规信息1、可不用危险警示，根据德国易燃液体管理规定，本产品属非易燃物；2、根据德国检测方法的分类（1999/5/17），本产品不危害水源其它信息无制作：审批人：。