2010-1-12 Inspection Criterion

Inspection CriterionCategory: Regular TestingRev# Date: 2006 / Feb / 10thRev# 0T e s t p r o c e s s v e r i f y1 Machine isn't well use 机台使用不正确 V 2Operator isn't qualify 操作者不够资格 V 3 Testing procedure isn't correct 测试程序不正确V 4 haven't Calibration data at site 无校准纪录 V 5not Suitable Gauge and checking fixture 无检具V6 incorrect test standard or outdated QR as criteria 测试标准不正确 V 7I m p a c t t e s t - E x t e n s i o n1 Testing load weight isn't correct 施重不正确 V (1). BIFMA: Functional load is 225lbs; Proof load is300lbs (2).Kmart and Target: 200lbs (3). Wal-mart: 225lbs 2Drop times isn't correct 冲击次数不正确V(1). BIFMA: Functional load1 drop; Proof load 1 drop (2). Kmart, Wal-mart and Target: 1 drop3 Impact height isn't 6" 冲击高度 V4 Requirement level isn't correct V (1). BIFMA: After functional load test, no loss of serviceability; After proof load test, no sudden and majoy change in thestructural integrity(2). Kmart and Target: less than 1/4" of permanentdeformation (3). Wal-mart: no majoy change in the structural integrity or component damage5o t a t i o n-E x t e n s i1.1transportation/vibration test doesn't meet 14200 times 震动次数V1.2transportation/vibration test, it doesn't lift to allow 1.5 mm sheet move freely under carton 纸箱没有离测试台面1。

5mm V2.1carton drop test, the drop height isn't meet ISTA standard 摔箱高度V2.2carton drop test, no make sure the most poorest corner being impacted 不是最弱角受冲击 V3vibration test system with a <25mm fixed controlled displacementV25mm fixed or controlleddisplacement4after transportation/vibration or carton drop test, the packaging have holes, tears, or openings, and the product have visible damage. 测试失败 V5S a l t S p a r y - E x t e n s i o n1before do testing, the speciments aren't clean 测试设备不干净V2the speciments place method isn't correct 测试方法不正确Vthe speciments should besupported or suspended between 15 and 30° from the vertical3the speciments can contact each other or any metallic material or any material capable of acting as a wick V4testing time isn't enough 测试时间不够V5after testing, handle method isn't correctVthe sepciments may be gently washed or dipped inclean running water not warmer than 38℃ to remove salt deposits from their surface.6S t r u c t u r e & F u n c t i o n1gap between metal and plastic parts over 2mm 金属件与塑胶件缝隙大于2mmV 2.1 welding-- sharp edge may cause injury 焊接，尖边 V 2.2 welding-- burrs/ line 焊接痕或毛边V 2.3 welding-- pit or splatter or pin holes 焊接，凹坑，飞溅，针孔V 2.4 welding-- false welding 虚焊V 2.5welding joint too minor,may affect function 焊接点太小V2.6 mesh welding loose 网脱焊 V 2.7 welding through parts 焊穿V 3rivet isn't rolled properly and tightly 铆钉未完全翻边V4 screw isn't locked tightly, not in place. 螺丝未锁紧或锁不到位V 5.1 fold/unfold not smoothly 折叠机构不顺 V 5.2 can't be folded/unfolded 折叠机构不可用V 6 parts assembled so loose that may cause drop off 部件未装紧V 7 Scissoring, shearing, pinching 剪，切点 V 8.1wobble on level floor, deviation 2~8mm 三条腿，2~8mmV8.2 wobble on level floor, deviation over 8mm 三条腿，大于8mm V 9 missing part 少件V 10 any functional problem 功能缺陷V 11parts aren't assembled correctly. 部件组装不正确V S t e p S t o o l - E x t e n s i o n1gap between front&rear leg over 2mm on U shape leg step stool U 型腿结构，前后差2mm 以上V2 latch mechanism too tight to operate, too loose to be locked 锁紧机构太紧或太松V3 end cap loose, failure pulling test 脚套松，未通过测试V4 tray/drawer can't be operated smoothly or too loose 抽屉，托盘太松或者不能操作V5 gap on plastic hinge cover over 2mm 塑胶铰链缝隙大于2mmV 6handle can't work well 把手运作不顺畅V L a d d e r - E x t e n s i o n1.1hinge doesn't meet cyclic test 6000 times 铰链6000 次循环测试失败V1.2hinge cover assembled incorrect in direction 盖子组装方向不正确V 2 rung isn't rolled properly 踏板未能翻边完全 V 3 lock latch don't pass 6000 times testing 锁紧机构不能通过6000 次测试V 4 burr on inner section 内踏板尖锐手感 V 5.1 gap on hinge 0.7~1.0mm 铰链的缝隙V 5.2 gap on hinge over 1.0mm, pass testing 铰链的缝隙大于1.0mm ，测试通过V 5.3gap on hinge so big that affect function 铰链的缝隙V太大，测试失败6 welding joint on rung doesn't meet request 踏板含焊接不能满足图纸要求V7 fly section doesn't cooperate base section well ，gap over 5mm 内外梯的间隙大于5mm V8 warning word on fly section and COSCO logo blurry 警告词模糊V 9 label placement incorrect 标签（方向标）位置不正确 V T a b l e - E x t e n s i o n1 screw broken 螺丝断V 2table collapse because of leg mechanism problem. 桌子倒塌V3.1 leg outwards/slanting more than request 腿管外趴超过要求V3.2 leg inwards/slanting, pass testing 腿管内趴超过要求，测试通过V3.3 leg inwards/slanting, table fail testing 腿管内趴超过要求，测试失败V4 end cap loose, failure pulling test 脚套松，未通过测试V 5 legs rub each other when folding 折叠时腿管交涉 V 6the end of leg is upward, over table edge 腿管上翘V7.1the edge of ABS sheet peels off due to gluedoesn't work well, less than 3 cm in length 脱胶， 小于3 cmV7.2the edge of ABS sheet peels off due to glue doesn't work well, more than 3 cm in length 脱胶， 大于3 cmV7.3the edge of ABS sheet peels off due to glue doesn't work well, more than 10 cm in length 脱胶， 大于10cm V8.1rivet/screw isn't assembled in place, table pass testing 铆钉，螺丝没装到位V8.2 rivet/screw isn't assembled in place, table fail testing 铆钉，螺丝没装到位，测试失败V9 lock mechanism assembled incorrectly, too tight, pop out 锁紧机构组立不正确，太紧，自动弹出 V 10 tabletop bubble 桌面鼓包 V 11 gap on T-mold 封边条缝隙V 12 gap between frame&tabletop more than 2mm 缝隙大于2mmV 13 vinyl break/ torn 布破V 14.1tabletop doesn't cover frame well, positionVdeviation 面板与边框位置偏移14.2tabletop exceed frame, less than 2mm 面板超出边框V14.3 tabletop exceed frame, more than 2mm 面板超出边框，大于2mmV 15 tabletop wrinkle 面板波浪状 V 16 frame warpage 边框翘曲V 17 plug fall out, small part 塞子掉出，小部件 V C h a i r - E x t e n s i o n1 gap between seat frame and pad more than 2mm 缝隙大于2mmV 2end cap loose, failure pulling test 脚帽松，测试失败 V 3 plug fall out , small part 塞子掉出，小部件 V 4.1 gap on backrest less than 2mm 靠背上缝隙 小于2mmV 4.2 gap on backrest 2~5 mm 靠背上缝隙 2~5mm V 4.3 gap on backrest more than 5 mm 靠背上缝隙 大于5mm V 5C r i b - E x t e n s i o n1Opening of gap, hole and channel doesn't meet the finger entrap requirement. 5.33~9.53mm 缝隙、孔大小在5。