EVH1型断路器说明书
EVH1-12系列用户培训
5. 常见问题及解决
断路器合闸常见问题； 断路器分闸常见问题； 其他问题；
2019/2/28
EVH1-12系列
46
断路器合闸常见问题
a. 断路器合不上闸。可能原因如下：
① 断路器进出车不到位，合闸回路不通。 ② 综保和断路器同时带防跳装置。应去除其中之一。 ③ 二次回路线（一般是外部接线）接错或线圈损坏。 出现此类问题，电磁铁动铁芯无动作反应，打开断 路器面板进行检查，如果合闸电磁铁无动作反应， 则对合闸电磁铁和二次回路接线逐一检查。 ④ 动铁芯卡滞。此时线圈有动作反应，检查电磁铁周 围有无杂物，动铁芯是否被卡住。 ⑤ 控制电压太低。
2. 清洁
安装后投运前应对断路器进行彻底清 扫，投运以后的断路器应定期进行清扫以 保持绝缘件、导电件表面的清洁。
清扫应在断路器主辅回路都不带电的 情况下进行。
2019/2/28
EVH1-12系列
42
3. 润滑 润滑部位：
a. 包括操动机构在内的断路器的各传动部位； b. 与断路器安装部分有关的传动部分；（例如 断路器使用在移开型开关柜的情况下）断路器与 开关柜其他部分之间联锁的传动部分； c. 当断路器使用在移开型开关柜中时，断路器 上一次隔离插头的接触部位应定期清理并涂新的 凡士林油。
额定短路开 断电流 25kA
31.5kA
80kA
2000 A 2500A 3150A 1250-2000A
EVH1 EVH1
---
40kA
130kA
2500-3150 1600-2500 A
EVH1 EVH1 --
50kA
130kA
i-AY-40.5样本
5外形及安装尺寸6
5.1i-AY1-40.5开关柜外形尺寸6
5.2EVH1-40.5断路器手车的外形尺寸6
5.3设备安装及地基参考图7
5.4开关柜母线桥安装尺寸8
6二次接线图8
7订货须知9
7.1一次线路系统图10
7.2二次线路原理图10
8随机文件10
9一次接线方案10
1
i-AY1-40.5铠装型移开式交流金属封闭开关设备，是由天水长城开关厂有限公司推出的新产品，可配用自行研究开发的EVH1-40.5新型真空断路器。作为三相交流50Hz的户内成套配电装置，用于接受和分配40.5kV的网络电能并对电路施行控制保护及监测。
图2 EVH1-40.5断路器手车外形图
5.3
开关柜安装基础的施工应符合“电力建设施工及验收技术规范”中的有关规定，开关设备安装基础示意图详见图3。
图3 i-AY1-40.5开关柜地基图及基础槽钢埋放示意
注：
1.基础槽钢顶面高出地面3~5mm；基础框架的平面度允差为±1mm/m，直线度允差为±1mm/m，但在框架总长度内的总偏差应不大于2mm
kV
40.5
2
额定绝缘水平
1min工频耐受电压(有效值)
kV
95
雷电冲击耐受电压(峰值)
185
3
额定频率
Hz
50
4
额定电流
A
630、1250、1600、2500
5
额定短时耐受电流
kA
31.5
6
额定峰值耐受电流
kA
80
7
额定短路持续时间
s
4
8
额定短路关合电流(峰值)
kA
80
EVH1系列断路器用户培训
130 4 50
44% 分-180s-合分-180s-合分
130 12.5 43.4
25 630 400 20 ≤15 10000 20 AC220, DC220 50
第二部分：技术参数
序号
1
2 3 4 5 6 7 8 9 10 11 12 13
名
称
额定电压 额定绝
1min工频耐受电压
缘水平
冲击耐受电压(峰值)
额定短时耐受电流
kA
额定峰值耐受电流
kA
额定短路电流持续时间
s
额定短路
交流分量有效值
kA
开断电流
直流分量百分数
额定操作顺序
额定短路关合电流
额定失步开断电流
kA
额定异相开断电流
额定电缆充电开断电流（有效值）
额定单个电容器组开断电流（有效值）
A
额定容性开合电流（C2级）
额定背对背电容器组开断电流（有效值）
EVH1系列户内高压交流真空断路器
介绍目录
第一部分：概述 第二部分：技术参数 第三部分：使用环境要求 第四部分：产品结构及工作原理 第五部分：搬运 第六部分：安装 第七部分：检查 第八部分：操作 第九部分：维护
第一部分：概述
1、主要用途及适用范围 EVH1系列户内高压真空断路器是三相交流50Hz,额定
3
4 5 6 7 8 9 10
额定绝缘水 平
名称 额定电压
1min工频耐受电压 冲击耐受电压(峰值)
额定电流
额定短路开断电流 额定短路关合电流(峰值)
额定峰值耐受电流 额定短时耐受电流
电寿命 额定短路电流持续时间
额定操作顺序
单位 kV kV
施耐德真空断路器样本说明书ev12_hvx区别型号厂家价格代理商高压10KV_mte20n户内真空高压断路器
安装
DB112206 DB112205 DB112207
A-14
底板安装
穿板安装
导轨安装
DB112209
抽出式EasyPactCVS400 安装方式
连接位置
抽出位置
移开断路器
DB111369 DB112219
抽出式断路器
抽出式具备插入式的所有优点，而且非常便于操作。抽出式断路器有三个位置： Q 连接位置：电源回路接通。 Q 抽出位置：电源回路断开，可以操作断路器以检查辅助回路。 Q 移开断路器：断路器可以从底座上取下来。
36
50
36
50
F
N
70
90
36
50
18
38
A
b
25,000
12,000
100, 150
b
b
b
b
b
b
b
b
b
b
b
b
105 * 161 * 86 1.6
105 * 161 * 86 1.6
CVS250
3
220
220
690
8
440
H
F
N
100
70
90
70
36
50
65
36
50
H
F
N
100
70
90
70
36
50
保护类型 Q 3极 (3P 3D)：三极本体（3P）；所有三极都具备保护功能（3D）。
最高提供250 kW的电动机保护
电动机保护额定值 (kW)
CVS 100/160/250
1.1…110
CVS 400/630
E-VAC系列中等电压真空断路器产品说明说明书
Ideal contact material and geometry ensure lowchopping current and reliable contact resistanceA few components and compact and reasonable structure ensure morereliable and safer operation Enable ideal cutoff and close of resistance, inductance load and capacitive loadSecondary plug, chassis, moving contact and grounding methods are specially designed ,completely compatible with domestically dominantmedium voltage switchgearProduct modelsE-VAC vacuum circuit breaker120E-VAC(R)i40/3150-210Voltage ratingsE: IEC/GB standardEaton circuit breaker seriesR indicates fixed type,none indicates drawout typei indicates solid-envelope d pole, none indicates assembled polerated short circuit breaking current ratedcurrentphase spacing1E-VAC series medium voltage vacuum circuit breakerProduct descriptionContentsDescription Page 156810E-VAC series medium voltage vacuum circuit breakerProduct description .................................................................Technical data ..........................................................................Dimensions .............................................................................Wiring diagram ........................................................................E-VAC series vacuum circuit breaker selection table ..............E-VAC vacuum circuit breakerProduct descriptionE-VAC Series medium voltage vacuum circuit breakers from Eaton Electrical combine our excellent vacuum technology with decades of experience in designing and manufacturing power distribution system. They offer high reliability, ease of handling and maintenance, high cost efficiency for different customers.Meet IEC, GB and DL standardsE-VAC equipped with new generation vacuum interrupter, suited fortechnologies and operation condition of power system••••••Technical featuresE-VAC utilizes mature spring operating mechanism, offers reliable and stableperformance, long service life, ease of operating,excellent corrosion protection and low maintenance within the lifetimeE-VAC adopts vertical epoxy insulation cover which can prevent harsh environment influence, making E-VAC circuit breaker suitable for various applications. Unique contact material and primary plum-shaped moving contact make E-VAC suitable for medium voltage system in various applications.E2 level electrical life extended and M2 levelmechanical life extended as per standard, capacitivecurrent breaking and making having extremelylowre-breakdown probability C2 level, having completed the type testAll products have been subject to hundreds of mechanical operation running-in tests beforeleaving the factory, ensuring the product performance in the most stable phase Utilize advanced imported testing equipment, exactly record no-load mechanical characteristics of each product, and provide users with these characteristic curves, ensure product reliability2Application conditionAmbient air temperature not exceeding 40℃, and the average value measured within 24 hours not exceeding 35℃. The minimum ambient air temperature is -15℃The effect by solar radiation can be ignoredThe ambient air is notobviously polluted by dust, smoke, corrosive orflammable gases, vapor or salt mistSeismic intensity not exceeding 8 degreeAmplitude of electromagnetic interference induced in secondary system not exceeding 1.6kV•••••••Outline dimension anddistribution panel interlocking method completelycompatible with domestically dominant medium voltage switchgear, high universality, significantly reduce design costProduct assembly utilizes tooling method to ensure dimension consistency. All products have been subject to the push panel test for standard panel, ensuringproduct interchangeability and universality•••••As the manufacturer of theworld’s first vacuum interrupter, the pioneer of vacuumtechnology, Eaton Electrical has been committed to the research, development and manufacturing of vacuum interrupters for over 70 years, and gathered plenty ofexperience. Westinghouse has become the synonym of quality and reliability.We own the world’s largest and globally leading vacuuminterrupter plant and the only vacuum interrupter plant that is equipped with large capacity high voltage laboratories.Our manufacturing capacity and design and development always maintain a leadership position.Application areasTechnology creation historyOptional accessoriesCharging handle Trolley handleLifterE-VAC series medium voltage vacuum circuit breakerProduct descriptionChemical industry Oil industry Piping industry Offshore mining ShipbuildingPaper making industry Opencast coal mine SubstationCement industry Automotive industry Power plantTextile and food industries Metallurgical industry•••••••••••••Temperature conditionThe average of relativehumidity measured within 24 hours not exceeding 95%The average vapor pressure measured within 24 hours not exceeding 2.2kPaThe average of relative humidity measured within one month not exceeding 90%The average vapor pressure measured within one month not exceeding 1.8kPa••••3E-VAC vacuum circuit breaker requires almost no relevant maintenanceIdeal for control and protection in medium voltage power supply and distribution systemSimple structure design of E-VAC vacuum circuit breaker further minimizes faultoccurrence, simplifies daily maintenance. With theindicator on the circuit breaker panel, no detection instrument is required, facilitating the judgment of working state of circuit breaker.The circuit breaker utilizes the world’s first class EatonElectrical’s vacuum interrupter with vacuum degree up to 10-6Pa, low air leakage, and ensure 50-year life with no maintenance required.The circuit breaker is equipped with superior spring charging mechanism, utilizes modular design, offering optimized mechanism main partdistribution, simpler structure and more reliable performance. The whole mechanism is composed by three modules: charging, closing, opening. Assembly and maintenance of these three parts are very simple. The spring charging mechanism composed by ratchet wheel mechanism,oscillator and closing spring is compact and smart. Theoperating mechanism is usually equipped with manual charging device and electric charging device, enabling automatic reclosing function.The circuit for manual charging operating mechanism isprovided with manual opening and closing operation buttons, circuit breaker position indicator and spring mechanism charging status indicator, switch operations counter, shunt release auxiliary switch, position and fault signals, etc..The circuit breaker of electric charging operating mechanism: added with spring charging motor, shunt release, trip free relay, and auxiliary switch for spring charging motor release.The following accessories can also be provided as needed: undervoltage release,overcurrent relay, etc..E-VAC series medium voltage vacuum circuit breakerProduct description4Main specification and technical parametersItem Unit Value Technical parameters for trip/close coilsNameParameter Note: (1)forced air cooling is required at 4000A; (2) If the user has special requirements, up to 125kA.O-0.3s-CO-180s-CO, O-180s-CO-180s-CO(50kA)5Technical dataE-VAC series medium voltage vacuum circuit breakerT echnical dataRated operating sequenceCharging duration Rated power of spring charging motor Rated voltage of spring charging motor Rated opening operating voltage Rated closing operating voltage Allowable accumulated wearingthickness of moving/fixed contact Rated short circuit current breaking cycleRated current breaking cycleMechanical lifeClosing time Opening time Secondary circuit power frequency withstand voltage (1 min)Rated short circuit making currentRated peak withstand current Rated currentRated frequency Rated lightning impulse withstand voltage (peak)Rated short-time power frequency withstand voltage (1 min)Rated voltageRated short-circuit breaking current Rated short-time withstand current (4s)Hz A kVkA kA kA kA V ms ms Cycle Cycle Cycle mm V V W s1242(phase to ground, phase to phase) 48 (gap)75 (phase to ground, phase to phase) 85(gap)506301250630 12501600 20001250 16002000 25003150 4000(1)1250 16002000 25003150 4000(1)252531.531.54040505063638080100(2)100(2)125130200020~5035~7020000, (10000 cycles at 50kA)20000, (10000 cycles at 50kA)E2(274)3AC 110/220AC 110/22065, (80W at 50kA)≤15DC 110/220V AC 110/220 DC 110/220DC 110/220Normal working voltage rangeRated working voltage (V)Rated working current of close coil (A)Rated working current of trip coil (A)AC, DC110AC, DC2202.0 1.01.80.9Closing: 80%~110% of rated working voltageOpening: 65%~120% of rated working voltage, opening will not occur when the normal working voltage is less than 30% of rated working voltageOutline and dimension of E-VAC circuit breaker (drawout type)Rated short circuit breaking current (kA)Rated current (A)Distribution panelwidth(mm)W S R N M L K J G F E D C B A H P T 6E-VAC series medium voltage vacuum circuit breakerDimensionsDimensions80080080080010001000100010001000630125016001250630125016001600~20002500~400020~31.520~4031.540(Short-circuit 125)20~31.520~4031.531.5~5031.5~50210210210275275275275275275275275275310275275275310310638638638638838838838838838652652652652852852852852852640640640640838838838838838650650650650850850850850850433433433361433433433361361626626626680626626626680680354955793549557910928028028029528028028029529559859859858659859859858658676767677767676777778787888787878888863763763769863763763769869850850850853650850850853653627727727727737737737737737740404004040400023232319313131313180010001000630~1600630~16001600~4000275275210310275275650720520720720520770770588632580580786590IIIII I 275275250252237237465455455Outline and dimension of E-VACR circuit breaker (fixed type)Note: during installation, make sure copper busbar reliably contacts the conductive surface of circuit breaker outlet in free state. Do not exert external force on the copper busbar to adjust its shape. Forced installation is not allowed!Distribution panel width Rated current (A)P H A B C E F G1\G2I J K 7E-VAC series medium voltage vacuum circuit breakerDimensionsE-VAC series medium voltage vacuum circuit breakerWiring diagramWiring diagramSecondary control connection diagram of E-VAC series vacuum circuit breaker (drawout type)The diagram shows the circuit breaker in test position, opening, discharged states8E-VAC series medium voltage vacuum circuit breakerWiring diagramSecondary control connection diagram of E-VACR series vacuum circuit breaker (fixed type) The diagram shows the circuit breaker in opening, discharged states9E-VAC series vacuum circuit breaker selection table1. Circuit breaker models2. Parameters of E-VAC series vacuum circuit breaker3. Technical parameters of spring operating mechanism4. Optional configuration (Standard option includes trip free device. Please note if the trip free device has to been canceled)E-VAC (drawout type)□E-VACR (fixed t ype)□Note: Technical parameters of products will be changed without notice. Please confirm with Eaton Corporation before ordering.10E-VAC series medium voltage vacuum circuit breakerE-VAC series vacuum circuit breaker selection tableParameters NameParameters NameName800Panel width(mm)Breaker phase spacing(mm)Rated short circuit breaking current (kA)(kA)Rated working current (A)21010002752531.540（Short-circuit 100kA ）40（Short-circuit 125kA ）31.54050□630□630□1250□1250□1250□1250□1600□1600□2000□1600□2000□2500□1600□2000□2500□3150□4000*□3150□4000** Forced air cooling is required at 4000AOpening power supply (V)Closing power supply (V)Spring charging motor power supply (V)□DC110□DC110□DC110□AC110□AC110□AC110□DC220□DC220□DC220□AC220□AC220□AC220□Overcurrent release □Closing latch □Position latch □Trip free relay □Undervoltage release □Operating handle□2 Overcurrent □3 Overcurrent□A□V □V □V □V□Quantity neededEaton is dedicated to ensuring that reliable, efficient and safe power is available when it’s needed most. With unparalleled knowledge of electrical power management across industries, experts at Eaton deliver customized, integrated solutions to solve our customers’ most critical challenges.Our focus is on delivering the right solution for the application. But, decision makers demand more than just innovative products. They turn to Eaton for an unwavering commitment to personal support that makes customer success a top priority. For more information,visit /seasia-electrical.Electrical Sector Asia PacificNo.3, Lane 280, Linhong Road,Changning District, ShanghaiEaton Industries Pte LtdElectrical Sector4 Loyang Lane #04-01/02Singapore 508914/seasia-electrical© 2013 Eaton Corporation All Rights Reserved Printed in SingaporeJuly 2013Eaton is a registered trademarkof Eaton Corporation.All trademarks are property of their respective owners.。
新EVH-24使用说明书
表1
序号
名
称
单位
数值
1 额定电压
kV
2 额定绝 1min 工频耐受电压 kV
缘水平 冲击耐受电压(峰值)
3 额定电流
A
4 额定短路开断电流
5 额定短路关合电流(峰值) kA
6 额定峰值耐受电流
7 额定短时耐受电流
8 电寿命
次
9 额定短路电流持续时间
s
10 额定操作顺序
11 机械寿命
次
12 额定单个电容器组开断电流
4.3.1 产品外形尺寸
图：EVH1-24 外形尺寸及安装与配合尺寸 1250A.…..25kA
4.4 工作原理
4.4.1 灭弧室
EVH1-24型真空断路器配用陶瓷真空灭弧室,采用铜铬触头材料,杯状纵磁场触头结构,触头 的电磨损速率小,电寿命长,耐压水平高,介质绝缘强度稳定,弧后恢复迅速,截流水平低,开断能力 强。
3SE4206
AC11 3A/380V
储能位置开关
辅助开关 S2
F10-16
AC 10A/380V
断路器主触头辅助开关
辅助开关 SW、YW
F1-41/Y.H
AC 10A/660V
试验、工作位置开关
3. 使用环境要求
a) 周围空气温度上限不高于+40 °C、下限不低于-15°C； b) 海拔不超过 1000m 相对湿度应控制在日平均值不大于 95%，月平均值不大于 90%； c) 饱和蒸气压应控制在日平均值不大于 2.2kPa，月平均值不大于 1.8kPa； d) 安装地点应无经常性的剧烈震动； e) 周围空气应不受腐蚀性或可燃性气体，水蒸汽的明显污染； f) 安装场所应保持干燥、清洁。
EVH1型断路器说明书
E H 系列户内高压真空断路器是三相交流 5H , V1 0 z 额定电压为 3 6 2k 的户内装置, . ~4 V 可 供工矿、企业、发电厂及变电站作电气设施的控制和保护之用。本产 品符 合标 准 G 1 8 -0 3 B 9 4 20《高压交流断路器》、J 3 5《户内高压交流真空断路器》、D4 3 0 B85 L0《1 ～ 3k 5 V户内高压真空断路器订货技术条件》和 I C2 7 -0 ：20 《高压交流断路器》 E 62 1 10 01 的有关规定。 EH V 1系列户内高压真空断路器既可装入手车式开关柜, 也可装入固定式开关柜。该 断路器具有寿命长、维护简单、无污染、无爆炸危险、噪音低等优点, 并且适应于频繁 操作等比较苛刻的工作条件。 2 技术数据 2 1 断路器主要的技术参数，见表 1 . ，表 2 。 表1 序号 1 2 名 称 单位 额定电压 k V 额定绝 1 i 工频耐受电压 mn k V 缘水平 冲击耐受电压( 峰值) 额定电流 额定短路开断电流 额定短路关合电流( 峰值) 额定峰值耐受电流 额定短时耐受电流 电寿命 额定短路电流持续时间 额定操作顺序 机械寿命 额定单个电容器组开断电流 额定背对背电容器组开断电流 A 60 3 2 5 8 0 8 0 2 5 数 1 2 4 2 7 5 15 20 20~ 50 15 10 20 60 20 00 ~ 35 10 20 00 3. 15 4 0 8(0) 010 1010 0(3) 8(0) 010 1010 0(3) 3. 15 4 0 3 0 4 分- . s合分-8 s 合分 0310 200 00 200 00 100 00 60 3 40 0 值
z34sm0601evh1系列户内高压交流真空断路器使用说明书额定电压kv241min工频耐受电压65额定绝缘水平冲击耐受电压峰值kv12563016002500额定短路开断电流25315额定短路关合电流峰值5063额定峰值耐受电流5063额定短时耐受电流ka2531510额定操作顺序分03s合分180s合分11机械寿命1000012额定单个电容器组开断电流63013额定背对背电容器组开断电流40022断路器装配调整后evh112t63025evh112t1250315evh112t1600315其机械特性参数应符合表接触行程3505相间中心距离mm1701521015分闸时间当操作电压为ms3050合闸时间ms3575分闸速度刚分5mm14020802断路器装配调整后evh112t2000315evh112t125040evh112t315040械特性参数应符合表4的规定
EVI-HD1操作说明书
部件与控制的位置及功能 7
2 开关2 (通讯波特率选择) 设置为ON时波特率为38400 bps，设为 OFF时波特率9600 bps。
注意
在打开电源前需先设置波特率。关闭电 源后的通讯比特率设置无效。
3 开关 3 (无用)
此开关应设为OFF。
4 开关4 (无用)
此开关应设为OFF。
遥控器(随机提供)
注意
• 在打开摄像机电源前需确认已经设置好了 旋钮。在摄像机处于待机状态时也进行旋 钮设置。设置完成后，使用随机提供的交 流电适配器和交流电力线将其与电源插座 连接，或使用 VISCA 指令打开摄像机电源。 将旋钮设置为待机状态时，按下遥控器上 的“电源”按键。旋钮设置即可生效。
• 改变旋钮位置时，需使用十字改锥。如果 使用其它类型的工具强行操作，可能导致 十字槽损坏。
部件与控制的位置及功能 5
概述
后部
qa 高清暑促会分量接口 以模拟分量 (YPbPr) 信号的格式输出图像。
qs 高清输出HD-SDI 接口 以符合SMPTE292M 串行数字接口标准 的HD-SDI 信号的格式化输出图像。
qd 红外线选择开关 使用同一个遥控器操作多台摄像机时， 选择摄像机的数量。
为防止热量聚集，不要妨碍摄像机周围的空 气流通。
运输
在运输摄像机时，需按照原厂包装，或者使 用同等质量的材料进行包装。
主要部件的清洁
摄像机机身变脏时，请用拧干的浸有淡中 性清洁剂的软布进行清洁。最后用干布擦 干表面。
不要使用任何类型的溶剂，这可能损坏设 备保护层。
如果使用化学布料，请按照使用说明操作。 不要向摄像机上喷洒挥发性物质，例如杀
连接 ........................................... 71 与交流电插座连接 ................ 71 与计算机连接 ....................... 71 与装有模拟分量(YPbPr) 输入接 口的视频监视器等设备连 接 ............................... 72 与装有复合视频输入接口或S视 频接口的视频监视器、磁 带录像机等设备连接... 72 与装有HD-SDI输入接口的磁带 录像 ................................ 机连接 ........................ 73
满足电网规范的中压开关设备新技术
外形尺寸(mm)
宽 12kV 国网 12kV 40.5kV 国网 40.5kV 800(1000) 800(1000) 深 1500 （1800） 1500 （1800） 高 2125 （2365） 2260 2525 2600
1400 2670 1400（1200） 2800
结构设计
•照明装置 •专用的接地铜母线。
主要产品
公司针对国网技术规范开发的开关柜主要有 i-AX-12（配EVH1-12）系列开关柜 i-AY1A-12（配EVS1-12）系列开关柜 i-AY1A-40.5（配EVH1-40.5）系列开关 柜。
EVH系列断路器
i-AX系列开关柜
38
KYN79A-12(i-AX-12) 户内铠装型移开式交流金属封闭开关设备 开关柜外观及结构说明
结构设计
40.5kV开关柜中一次母排端部采取倒圆角 的措施，且圆角直径为母排厚度。
结构设计
断路器室的活门应标有母 线侧、线路侧等识别字样。 活门连接活动部位，应设 计接地连接线。 活门与柜体壳体之间，应 设计接地连接线。
瑞侃热缩套管材料
开关柜内部导体采用的热缩绝缘材料老化 寿命应大于20年。开关柜寿命30年。
5
ZN63-12
结构简述
ZN63A-12真空断路器的的主回路采用全封闭结构，主回路部件纵向安装 在一个管状绝缘筒内，绝缘筒是由环氧树脂采用APG工艺浇铸而成，具 有良好的耐电弧、抗老化、高强度特性，可防止真空灭弧室受外部因素 的损坏，增加了导电回路本体承受动热稳定电流的能力。
EVH户内高压交流真空断路器
1991年美国威德曼公司
2002年芬兰“芬宝”公司引进的“午夜快车”
E-Series 电路断路器说明书
The E-Series hydraulic/magnetic circuit breaker is ideally suited not require a fuse back up. It is also UL recognized and CSA certified as a supplementary protector and as a manual motor Its physical features include front and back mounting, screw wire. The E-series is available with handle actuators and can*Manufacturer reserves the right to change product specification without prior notice.EnvironmentalPhysicalMechanicalElectricalDesigned in accordance with requirements of specificationMIL PRF-55629 & MIL-STD-202G as follows:Maximum Voltage 600VAC 50/60 Hz, 125VDC (SeeTable A)Current Ratings Standard current coils: 0.100, 0.250, 0.500, 1.00, 2.50, 5.00, 7.50, 10.0, 15.0, 20.0, 25.0, 30.0, 50.0, 60.0, 70.0 & 100 Amp.Auxiliary Switch Rating SPDT; 10.1A 250VAC, 1.0A 65VDC; 0.5A 80VDC, 0.1A 125VAC (with gold contacts). Insulation Resistance Minimum of 100 Megohms at 500 VDC.Dielectric Strength UL, CSA: 2200 V 50/60 Hz for one minute between all electrically isolated terminals. E-Series Circuit Breakers comply with the 8mm spacing and 3750V 50/60 Hz dielectric requirements from hazardous voltage to operator accessible surfaces, between adjacent poles and from main circuits to auxiliary circuits per Publications EN 60950 and VDE 0805.Resistance, Impedance Values from Line to Load Terminal - based on Series Trip Circuit Breaker.Endurance 10,000 ON-OFF operations @ 6 per minute; with rated Current and Voltage.Trip Free All E-Series Circuit Breakers will trip on overload, even when Handle is forcibly held in the ON position.Trip Indication The operating Handle moves positively to the OFF position when an overload causes the breaker to trip.Number of Poles 1 - 6Mounting A 3” minimum spacing must be provided between the circuitbreaker arc venting area on back connected E-Series circuit breakers and grounded obstructions. E-Series circuit breakers must be mounted on avertical surface.Connectors, Box Type Front connected E-Series circuit breakers are supplied with box type pressure connectors that accept copper or aluminum conductors as follows: 1/0-14Copper, 1/0-12 Aluminum.Internal Circuit Series and Switch Only, (with or Configuration without auxiliary switch). Shuntwith current coils.Weight Approximately 252 grams/pole(Approximately 9 ounces/pole)Standard Colors Housing-Black; Actuator - See Ordering Scheme.Shock Withstands 100 Gs, 6ms, sawtooth while carrying rated current per Method 213, Test Condition “I”. Vibration Withstands 0.060” excursion from 10-55 Hz, and 10 Gs 55-500 Hz, at rated current per Method 204C, Test Condition A. Moisture Resistance Method 106D, i.e., ten 24-hour cycles @ + 25°C to +65°C, 80-98% RH.Salt Spray Method 101, Condition A (90-95% RH @ 5% NaCl Solution, 96 hrs).Thermal Shock Method 107D, Condition A (Five cycles @ -55°C to +25°C to +85°C to +25°C).Operating Temperature -40° C to +85° CPulse Tolerance CurvesElectrical TablesTable A: Lists UL Listed (489) & CSA Certified (C22.2 No. 5) configurations & performance capabilities as a Molded Case Circuit Breaker.Table B: Lists UL Recognized & CSA Accepted configurations & performance capabilities as a Component SupplementaryAgency CertificationsUL Recognized UL Standard 1077UL Standard 1500UL ListedUL Standard 489CSA AcceptedCSA CertifiedTUV CertifiedVDE CertifiedComponent Recognition Program as Protectors, Supplementary (Guide QVNU2, File E75596)Component Recognition Program as Manual Motor Controls (Guide NLRV2, File E135367)Protectors, Supplementary for Marine Electrical & Fuel Systems (Guide PEQZ2, File E75596) Ignition ProtectionCircuit Breakers, Molded Case (Guide DIVQ, File E129899)Component Supplementary Protector (Class 3215 30, File 047848 0 000)CSA Standard C22.2 No. 235Circuit Breaker Molded Case (Class 1432 01, File 093910), CSA Standard C22.2 No. 5.1 - M EN60934 under License No. R72031056EN60934, VDE 0642 under File No. 10537Table C: Lists UL Recognized, CSA Accepted and VDE Certified configurations and performance capabilities as a Component Supplementary Protector.Table D: Lists UL Recognized, CSA Accepted configurations and performance capabilities as Protectors, Supplementary for Marine Electrical and Fuel Systems (Guide PEQZ2, File E75596). Ignition Protected per UL 1500. UL Classified Small Craft Electrical Devices, Marine in accordance with ISO 8846 (Guide UZMK, File MQ1515) as Marine Supplementary Protectors.Electrical TablesTable C Notes:1 Requires branch circuit backup with a UL LISTED Type K5 or RK5 fuse rated 15A minimum and no more than 4 times full load amp rating and not to exceed 225 amps.7 CURRENT RATING (AMPERES)7OR VOLTAGE COIL (MIN. TRIP RATING, VOLTS)5020 0.020025 0.025030 0.030035 0.035040 0.040045 0.045050 0.050055 0.055060 0.060065 0.065070 0.070075 0.075080 0.080085 0.085090 0.090090 0.095210 0.100215 0.150220 0.200225 0.250230 0.300235 0.350240 0.400245 0.450250 0.500255 0.550260 0.600265 0.650270 0.700275 0.750280 0.800285 0.850290 0.900295 0.950410 1.000512 1.250415 1.500517 1.750420 2.000522 2.250425 2.500527 2.750430 3.000435 3.500440 4.000445 4.500450 5.000455 5.500460 6.000465 6.500470 7.000475 7.500480 8.000485 8.500490 9.000495 9.500610 10.000710 10.500611 11.000711 11.500612 12.000712 12.500613 13.000614 14.000615 15.000616 16.000617 17.000618 18.000620 20.000622 22.000624 24.000625 25.000630 30.000635 35.000640 40.000650 50.000660 60.000670 70.000680 80.000690 90.000810 100.000811 110.000812 120.0009128 125.000CODE AMPERESA06 6 DC, 5 DC A12 12 DC, 10 DC A18 18 DC, 15 DC A24 24 DC, 20 DC A32 32 DC, 25 DC A48 48 DC, 40 DC A65 65 DC, 55 DC B25 125 DC, 100 DC J06 6 AC, 5 AC J12 12 AC, 10 AC J18 18 AC, 15 AC J24 24 AC, 20 ACJ48 48 AC, 40 AC J65 65 AC, 55 AC K20 120 AC, 65 AC L40 240 AC, 130 AC 1Series2Actuator3Poles6Frequency & Delay7Current Rating8Terminal12Agency Approval 4 Circuit5Auxiliary Switch E A B 01A22BC 244501 SERIES E2 ACTUATORAHandle, one per pole8 TERMINAL 12BACK CONNECTED (FRONT MOUNTED ONLY) MAX. RATING 19 10-32 Stud (All Terminals) 50 A 29 1/4-20 Stud (All Terminals) 120 A A 9 M5 Stud (Line & Load) 50 A B 9 M6 Stud (Line & Load) 100 A FRONT CONNECTED (BACK MOUNTED ONLY) MAX. RATING 310 Box Wire Connector (Line & Load) 100 A C 11 Box Wire Connector w/ Pressure Plate (Line & Load) 100 A 4 10-32 Screw (Line & Load) 50 A D M5 Screw (Line & Load) 50 A 5 10-32 “Bus-Type” Screw (Line), 10-32 Screw (Load) 50 A E M5 “Bus-Type” Screw (Line), 10-32 Screw (Load) 50 A 610 10-32 “Bus-Type” Screw (Line), Box Wire Connector (Load) 100 AF 1110-32 “Bus-Type” Screw (Line), Box Wire Connector w/ Pressure Plate (Load) 100 A 7 1/4-20 Screw (Line & Load) 100 A G M6 Screw (Line & Load) 100 A 8 1/4-20 “Bus-Type” Screw (Line), 1/4-20 Screw (Load) 100 A H M6 “Bus-Type” Screw (Line), M6 Screw (Load) 100 A 910 1/4-20 “Bus-Type” Screw (Line), Box Wire Connector (Load) 100 AJ 111/4-20 “Bus-Type” Screw (Line), Box Wire Connector w/ Pressure Plate (Load) 100 A10 MOUNTING/BARRIERSBACK CONNECTED (FRONT MOUNTED ONLY)Mounting Inserts A 6-32B ISO M3FRONT CONNECTED (BACK MOUNTED ONLY)14Back Mounting Foot Type Front Mounting Inserts (Optional Use)C Short 6-32 D Short ISO M3E Long 6-32 F Long ISO M33 POLES 11 One 2 Two 3 Three4 Four5 Five6 Six4 CIRCUIT 2A 3 Switch Only (no coil )B Series Trip (current )C Series Trip (voltage )DShunt Trip (current )E Shunt Trip (voltage )F Relay Trip (current )G Relay Trip (voltage )5 AUXILIARY SWITCH 40 without Auxiliary Switch2 S.P .D.T. 0.110 Q.C. Terminals3 S.P .D.T. 0.139 Solder Lug4 S.P .D.T. 0.110 Q.C. Terminals(Gold Contacts) 6 S.P .D.T. 0.110 Q.C. Terminals 7 S.P .D.T. 0.110 Q.C. Terminals (Gold Contacts)8 S.P .D.T. 0.187 Q.C. Terminals 9 S.P .D.T. 0.187 Q.C. Terminals6 FREQUENCY & DELAY033DC 50/60Hz, Switch Only 105 DC Instantaneous 12 DC Short 14 DC Medium 16 DC Long205 50/60Hz Instantaneous 22 50/60Hz Short 24 50/60Hz Medium 26 50/60Hz Long30 DC, 50/60Hz Instantaneous 32DC, 50/60Hz Short34 DC, 50/60Hz Medium 36 DC, 50/60Hz Long 62 50/60Hz Short, Hi-Inrush 64 50/60Hz Medium, Hi-Inrush 66 50/60Hz Long, Hi-Inrush 72 DC, Short,Hi-Inrush 74 DC,Medium, Hi-Inrush 76 DC, Long, Hi-Inrush926DC, 50/60Hz Short, Hi-Inrush 946DC, 50/60Hz Medium, Hi-Inrush966DC, 50/60Hz Long, Hi-Inrush 11 MAXIMUM APPLICATION RATING 1512 AGENCY APPROVALBDUL 1077 / UL508 Recognized & CSA Accepted UL 1077 Recognized, CSA Accepted, & VDE Certified 9Actuator Color10Mounting/Barriers11Maximum Application Rating9 ACTUATOR COLOR & LEGEND 13Actuator Color White Black Red Green Blue Yellow Gray Orange Legend Color Black White White White White Black Black BlackI-O A C F H K M P R ON-OFF B D G J L N Q S Dual12345678A 65 VDC, 120 A B 125 VDC, 120 A C 120/240 VAC, 100 A D 240 VAC, 100 A E 16 277/480 VAC, 100 A F 277 VAC, 100 A G 16 600 VAC, 100 A H 16 480 VAC, 100 A J 16 415 VAC, 100 A L 16 160 VDC, 100 A T 125 VDC/240 VAC, 100 A W 16 125 VDC/415 VAC, 100 A Notes:1 VDE approval on 1-5 poles only. Standard multi-pole units identical poles except when specifying auxiliary switch - (see Note 4). For mixed ratings, consult factory.2 Switch Only & Series Trip construction available w/either front or back connected terminals. Shunt construction available w/back connected terminals, (T erminal Codes 1 & 2) only. Circuit Codes B,C & D are VDE approved.3 Switch Only construction: 30 amps or less select Current Rating Code 630; 31-70 amps, select Current Rating code 670; 71-100 amps, select Current Rating Code 810; 101-125 amps Select Current Rating Code 912. Switch Only is VDE approved only if tied to a protected pole.4Auxiliary Switch available on Switch Only and Series Trip units. On multi-pole units, only one auxiliary switch is normally supplied mounted in the extreme right pole. Back mounted units require special mounting provisions when auxiliary switch is specified. VDE approval on Auxilary Switch Codes 0,2,3 & 4 only.5 Voltage Trip Coils are not rated for continuous duty. Available only with Frequency & Delay Codes 10 & 20. Series Trip construction with a voltage coil s VDE approved only if tied to a protected pole.6 Frequency & Delay Codes 92,94 & 96 are not VDE Certified.7 Current Coil Ratings 0.100 - 100 ams are VDE Certified.8 125 A rating (Code 912) available as a Switch Only (Circuit Code A), rated 125 VDC (Code B).9 An Anti-Flash Over Barrier is supplied between poles on multi-pole units with 10-32 (T erminal Code 1). 1/4-20 (Code 2), M5 (Code A), and M6 (Code B) terminals per UL requirement.10 Box Wire Connector will accept #14 through 0 AWG. copper wire or #12 through 0 AWG. aluminum wire.11 Box Wire Connector with Pressure Plate for stranded wire, consult factory for details.12 T erminal Codes A,B,D,E,G & H are not VDE Certified.13 VDE approvals require Dual (I-O, ON-OFF) or I-O markings on all handles.14 Back Mounted breakers can also be front mounted by utilizing the proper front panel mounting inserts normally supplied. However, terminal connections must be made prior to mounting.15 Application ratings B,D,J,T & W are available with VDE.16415, 480 & 600 VAC ratings require 3 or 4 pole break 3Ø and 2 pole break 1Ø.7 CURRENT RATING (AMPERES)7OR VOLTAGE COIL (MIN. TRIP RATING, VOLTS)5020 0.020025 0.025030 0.030035 0.035040 0.040045 0.045050 0.050055 0.055060 0.060065 0.065070 0.070075 0.075080 0.080085 0.085090 0.090090 0.095210 0.100215 0.150220 0.200225 0.250230 0.300235 0.350240 0.400245 0.450250 0.500255 0.550260 0.600265 0.650270 0.700275 0.750280 0.800285 0.850290 0.900295 0.950410 1.000512 1.250415 1.500517 1.750420 2.000522 2.250425 2.500527 2.750430 3.000435 3.500440 4.000445 4.500450 5.000455 5.500460 6.000465 6.500470 7.000475 7.500480 8.000485 8.500490 9.000495 9.500610 10.000710 10.500611 11.000711 11.500612 12.000712 12.500613 13.000614 14.000615 15.000616 16.000617 17.000618 18.000620 20.000622 22.000624 24.000625 25.000630 30.000635 35.000640 40.000650 50.000660 60.000670 70.000680 80.000690 90.000810 100.000811 110.000812 120.0009128 125.000CODE AMPERESA06 6 DC, 5 DC A12 12 DC, 10 DC A18 18 DC, 15 DC A24 24 DC, 20 DC A32 32 DC, 25 DC A48 48 DC, 40 DC A65 65 DC, 55 DC B25 125 DC, 100 DC J06 6 AC, 5 AC J12 12 AC, 10 AC J18 18 AC, 15 AC J24 24 AC, 20 ACJ48 48 AC, 40 AC J65 65 AC, 55 AC K20 120 AC, 65 AC L40 240 AC, 130 AC 1Series2Actuator3Poles6Frequency & Delay7Current Rating8Terminal12Agency Approval 4 Circuit5Auxiliary Switch E A B 01A22CC 244501 SERIES E2 ACTUATORAHandle, one per pole8 TERMINAL 7BACK CONNECTED (FRONT MOUNTED ONLY) MAX. RATING 18 10-32 Stud (All Terminals) 50 A 28 1/4-20 Stud (All Terminals) 125 A FRONT CONNECTED (BACK MOUNTED ONLY) MAX. RATING 39 Box Wire Connector (Line & Load) 100 A C 10 Box Wire Connector w/ Pressure Plate (Line & Load) 100 A 4 10-32 Screw (Line & Load) 50 A 5 10-32 “Bus-Type” Screw (Line), 10-32 Screw (Load) 50 A 69 10-32 “Bus-Type” Screw (Line), Box Wire Connector (Load) 100 AF 1010-32 “Bus-Type” Screw (Line), Box Wire Connector w/ Pressure Plate (Load) 100 A 7 1/4-20 Screw (Line & Load) 125 A 8 1/4-20 “Bus-Type” Screw (Line), 1/4-20 Screw (Load) 100 A 99 1/4-20 “Bus-Type” Screw (Line), Box Wire Connector (Load) 100 AJ 101/4-20 “Bus-Type” Screw (Line), Box Wire Connector w/ Pressure Plate (Load) 100 A10 MOUNTING/BARRIERSBACK CONNECTED (FRONT MOUNTED ONLY)Mounting Inserts A 6-32B ISO M3FRONT CONNECTED (BACK MOUNTED ONLY)11Back Mounting Foot Type Front Mounting Inserts (Optional Use)C Short 6-32 D Short ISO M3E Long 6-32 F Long ISO M33 POLES 11 One 2 Two 3 Three4 Four5 Five6 Six4 CIRCUIT 2BSeries Trip (current )C 3 Series Trip (voltage )5 AUXILIARY SWITCH 40 without Auxiliary Switch2 S.P .D.T. 0.110 Q.C. Terminals3 S.P .D.T. 0.139 Solder Lug4 S.P .D.T. 0.110 Q.C. Terminals(Gold Contacts) 6 S.P .D.T. 0.110 Q.C. Terminals 7 S.P .D.T. 0.110 Q.C. Terminals (Gold Contacts)8 S.P .D.T. 0.187 Q.C. Terminals 9 S.P .D.T. 0.187 Q.C. Terminals6 FREQUENCY & DELAY105 DC Instantaneous 12 DC Short 14 DC Medium 16 DC Long205 50/60Hz Instantaneous 22 50/60Hz Short 24 50/60Hz Medium 26 50/60Hz Long30 DC, 50/60Hz Instantaneous 32 DC, 50/60Hz Short 34DC, 50/60Hz Medium36 DC, 50/60Hz Long 62 50/60Hz Short, Hi-Inrush 64 50/60Hz Medium, Hi-Inrush 66 50/60Hz Long, Hi-Inrush 72 DC, Short,Hi-Inrush 74 DC,Medium, Hi-Inrush 76 DC, Long, Hi-Inrush926DC, 50/60Hz Short, Hi-Inrush 946DC, 50/60Hz Medium, Hi-Inrush966DC, 50/60Hz Long, Hi-Inrush 11 MAXIMUM APPLICATION RATING 12 AGENCY APPROVALCFUL 489 Listed & CSA Certified UL 489 Listed, CSA Certified, & VDE Certified 9Actuator Color10Mounting/Barriers11Maximum Application Rating9 ACTUATOR COLOR & LEGEND 12Actuator Color White Black Red Green Blue Yellow Gray Orange Legend ColorBlack White White White White Black Black BlackON-OFF B D G J L N Q S Dual 123456781 120 VACB 125 VDC, 120 AC 13 120/240 VAC, 100 AD 240 VAC, 100 ANotes:1 Standard multi-pole units identical poles except when specifying auxiliary switch - (see Note 4). For mixed ratings, consult factory. VDE Certification on 1-5 poles only.2 Series Trip construction available w/either front or back connected terminals.3 Series Trip construction with a voltage coil is not available as a single pole unit and must be tied to a protected pole.4 On multi-pole units, only one auxiliary switch is normally supplied mounted in the extreme right pole per Figure A. Back mounted units require special mounting provisions when auxiliary switch is specified. VDE Certification on auxilary switch codes 0, 2, 3 & 4 only.5 Voltage Trip Coils are not rated for continuous duty. Available only with Frequency & Delay Codes 10 & 20.6 Frequency & Delay Codes 92, 94 & 96 are not VDE Certified.7 Current Ratings under 0.100 amps are not VDE Certified .8 An Anti-Flash Over Barrier is supplied between poles on multi-pole units with 10-32 Stud (T erminal Code 1) or 1/4-20 Stud (Code 2) terminals per UL requirement.9 Box Wire Connector will accept #14 through 0 AWG. copper wire or #12 through 0 AWG. aluminum wire.10 Box Wire Connector with Pressure Plate for stranded wire, consult factory for details.11 Back Mounted breakers can also be front mounted by utilizing the proper front panel mouning inserts normally supplied. However, terminal connections must be made prior to mounting.12 VDE Certification requires dual (I-O , ON-OFF) markings on all handles.13 Not available with VDE Certification.Notes:1 All dimensions are in inches [millimeters].2 T olerance ±.020 [.51] unless otherwise specified.3 0-50 amps: 10-32 & M5 Studs .625±.062/15.88±1.574 long.4 51-120 amps: 1/4-20 & M6 Studs .750±.062/19.05±1.574 long.Notes:1 1/4 -20 stud terminal in Series Trip circuit configuration shown.2 A 3” min spacing must be provided between the circuit breaker arc venting areaof back connected E-Series circuit breaker and grounded obstructions.3 All dimensions are in inches [millimeters].4 T olerance ±.020 [.51] unless otherwise specified.5 Circuit breakers must be mounted on vertical surface.Notes:1 All dimensions are in inches [millimeters].2 T olerance ±.020 [.51] unless otherwise specified.3 Box wire connector terminal in Series Trip circuit configuration shown.4 Circuit breakers must be mounted on vertical surface.REV_CB_E_01_2014。
EVH1-12户内高压交流真空断路器(天水)
2.4 储能电机 ..................................................................... 4 2.5 2.6 分、合闸线圈的技术数据见表 5 ................................................ 4 辅助开关的技术数据见表 6 .................................................... 4
2.2 断路器装配调整后,其机械特性参数应符合表 2 的规定。 序号 1 2 3 4 5 6 7 8 9 名 触头开距 接触行程 相间中心距离 合闸触头弹跳时间 三相分闸不同期性 分闸时间 当操作电压为 最 高 额 定 最 低 称 表2 单位 mm 数 值
8±1 3±0.5 210±1.5 ≤2 ≤2 30-50
资 料 来 源 编 制 校 核 规格审查 审 定 批 准
标记 处数 更改文件号
签 字
日期
提出部门 批准文号
EVH1-12/T1250-31.5 户内高压交流真空断路器使用说明 书
Z34.SM.06.01
第 2 页 共 15 页
6 安装 ........................................................ 9
目
录
1 概述 ........................................................ 3 2 技术数据 .................................................... 3
2.1 2.2 2.3 断路器主要的技术参数，见表 1。 .............................................. 3 断路器装配调整后,其机械特性参数应符合表 2 的规定。 .......................... 3 断路器的主回路电阻值见表 3。 ................................................ 4
高压断路器中的弹簧操动机构
高压断路器中的弹簧操动机构刘唯2015.4摘要：本文讨论了断路器操动机构的功能，总结并比对了目前主流弹簧操动机构的实现方式，也介绍了各种结构的优缺点。
列举了断路器上弹簧机构的各种布局方式，从控制，安全，维护及发展的角度谈了个人看法。
关键词: 高压断路器弹簧操动机构目录0引言 (1)1操动机构的种类 (1)2弹簧操动机构的功能 (2)3断路器弹簧操动机构结构 (3)3.1储能结构的分类 (4)3.1.1储能操作的能量只用于合闸过程43.1.2储能操作的能量分别用于合闸或分闸过程4 3.2储能到位离合及状态保持结构 (5)3.3合闸驱动结构 (5)3.3.1不具备自由脱扣的结构63.3.2具备自由脱扣功能的结构6 3.4合闸状态保持结构 (6)3.4.1过冲复位保持结构63.4.2复位保持结构73.4.3就绪保持结构7 3.5储能电机的减速机构 (7)3.5.1齿轮箱结构73.5.2蜗轮蜗杆结构73.5.3棘轮结构7 3.6弹簧机构的联锁装置 (8)3.6.1硬联锁83.6.2软联锁83.6.3PF接点9 4断路器弹簧操动机构的布局 (9)5断路器的控制与保护 (10)6断路器操动机构的安全锁 (11)7断路器弹簧操动机构的维护 (11)8断路器弹簧操动机构的发展 (5)0引言笔者最近几年，接触了一些弹簧操动机构，有些认识，愿与大家分享。
文中没有计算，没有公式，略显没有深度，请高手一笑而过。
文中试图将千差万别的机械结构进行分类，会有遗漏，但终归是一次尝试。
也试图将其优缺点做一比较，必不完全，但肯定会有些说法。
有些机构，并不能完全理解其博大精深，不正之处，也还望请指正。
请到新浪微博《高压断路器中的弹簧操动机构》交流贴留言。
链接如下：/u/2437510622。
原文下载请搜百度文库。
文中涉及到一些机构名称，如ABB公司的EL弹簧操动机构，以下简称EL机构，主要用于VD4断路器；Schneider公司的P2弹簧操动机构，以下简称P2机构，主要用于Evolis断路器和Masterpact断路器；Schneider公司的RI弹簧操动机构，以下简称RI机构，主要用于Ev12S断路器上；Schneider公司的RT弹簧操动机构，以下简称RT机构，主要用于Premset 开关柜上；Schneider公司的FK2-01弹簧操动机构，以下简称FK2机构，主要用于HVX断路器上；三菱的BH2弹簧操动机构，以下简称BH2机构，主要用于VPR 断路器上；天水长城开关厂的GSL01弹簧操动机构，以下简称GSL01机构，主要用于EVH1断路器；以下断路器上用的弹簧操动机构不知道名字，只能用断路器名字称呼，VS1断路器上的弹簧操动机构，以下简称VS1机构；厦门华电开关有限公司的VEP断路器上的机构，以下简称VEP机构；Siemens公司的Sion断路器上采用的机构，以下简称Sion机构；东芝公司的VK断路器上采用的机构，以下简称VK机构。
电力设备：E-VAC EP系列中高压真空电路断路器说明书
E-VAC EP Series Medium Voltage Vacuum Circuit BreakerAutomotiveAerospaceTruckHydraulicsAutomotive Aerospace Truck Hydraulics Poweringbusiness worldwideEaton delivers the power inside hundreds of products that are answering the demands of today’s fast changing world. We help our customers worldwide manage the power they need for buildings, aircraft, trucks, cars, machinery and entire businesses. And we do it in a way that consumes fewer resources.Next generationtransportationEaton is driving the development of newtechnologies – from hybriddrivetrains and emission control systems to advanced engine components – that reduce fuel consumption and emissions in trucks and cars. Higher expectationsWe continue to expand our aerospace solutions andservices to meet the needs of new aviation platforms,including the high-flying light jet and very light jet markets. Building on our strengths Our hydraulics businesscombines localised service and support with an innovative portfolio of fluid powersolutions to answer the needs of global infrastructure projects, including locks, canals and dams.Powering Greener Buildings and BusinessesEaton’s Electrical Group is a leading provider of powerquality, distribution and control solutions that increase energy efficiency and improve power quality, safety and reliability. Our solutions offer a growing portfolio of “green” products and services, such as energy audits and real-time energy consumption monitoring.Eaton’s Uninterruptible Power Supplies (UPS), variable-speed drives and lighting controls help conserve energy and increase efficiency.ElectricalElectrical E-VAC EP Series Medium Voltage Vacuum Circuit Breaker 1Eaton Corporation is a worldwide leader in thedesign, manufacture, and sale of safe, reliableand high-performance medium voltage power distribution equipment in accordance with IEC,GB and ANSI standards.Complete Global Medium Voltage Switchgear Solutions Eaton, a premier leader in designing and manufacturing power distribution and protection equipment in the electrical industry, offers a comprehensive range of medium voltage (MV) solutionsto meet the needs of virtually every application. From productsthat feature cutting-edge design that allow for easy access, maintenance and space savings, to arc-resistant products that enhance safety, Eaton’s medium voltage solutions provide avariety of products for every need. Additionally, Eaton’s global service network provides maximum customer support in allregions of the world.As one of the few completely vertically integrated and diversified industrial manufacturers in the world, Eaton designs not only MV assemblies, but also the key components that comprise the MV solutions – from steel housing and circuit breaker compartmentsto vacuum interrupters, circuit breakers, bus systems and fuses. Eaton’s MV heritage, strengthened by acquisitions such as Westinghouse DCBU, Cutler Hammer, MEM and Holec, has resulted in breakthrough MV technologies and numerous international patents over the years.Part of Eaton’s complete electrical PowerChain Solutions– which help businesses minimize risks while realizing greater reliability, cost efficiencies, capital utilization and safety –Eaton’s medium voltage equipment meets all applicablestandards and certifications such as IEC, NEMA / ANSI, GB,UL, IEEE, KEMA and CSA.When it comes to medium voltage solutions, you can trust theone name with a long history of proven performance: Eaton.E-VAC EP Series Medium Voltage VacuE-VAC EP Series Medium Voltage Vacuum Circuit BreakerE-VAC EP Series medium voltage Ideal contact material and E-VAC EP Vacuum Circuit Breakervacuum circuit breakers from geometry ensure low Eaton Electrical combine our chopping current andexcellent vacuum technology reliable contact resistance . with decades of experience in designing and manufacturing A few components and power distribution system. They compact and reasonable offer high reliability, ease of structure ensure morehandling and maintenance, high reliable and safer operation. cost efficiency for Chinese users. Enable ideal cutoff and close Meet GB and DL standards. of resistance, inductance load and capacitive load. E-VAC equipped with new generation vacuum Secondary plug, chassis,interrupter, suited formoving contact and grounding technologies and operation methods are speciallycondition of power system. designed to Chinese users, completely compatible with E-VAC utilizes solid-enveloped domestically dominantpole of Eaton Electrical, offers medium voltage switchgear superior and reliable solid KYN28.enveloping insulation performance, passescondensation test, suitable for safely operating in harsh environment. It offers better creepage distance and clearance compared to the requirements in GB standards.Product modelsE -VAC -12 / T □ -□GB StandardEaton breaker seriesVoltage ratings kVRated current ARated short circuit breakingcurrent kASpring operation mechanismE-VAC EP Series Medium Voltage Vacuum Circuit Breaker3Application condition Technical features Temperature condition Ambient air temperature not E-VAC utilizes mature spring Product assembly utilizes The average of relative exceeding 40℃, and the operating mechanism, offers tooling method to ensure humidity measured within 24 average value measured within reliable and stable dimension consistency. All hours not exceeding 95%.24 hours not exceeding 35℃. performance, long service life, products have been subject toThe minimum ambient air ease of operating, excellent the push panel test for The average vapor pressure temperature is -15℃.corrosion protection and low standard panel, ensuring measured within 24 hours notmaintenance within the lifetime product interchangeability and exceeding 2.2kPa.The effect by solar radiation universality.can be ignored. E-VAC EP series 12kV vacuum The average of relativecircuit breaker adopts mature All products have been subject humidity measured within one The ambient air is not obviously APG process to enclose to hundreds of mechanical month not exceeding 90%.polluted by dust, smoke, vacuum interrupter and main operation running-in testscorrosive or flammable gases, conductive circuit in a before leaving the factory, The average vapor pressure vapor or salt mist. insulation tube, thoroughly ensuring the product measured within one montheliminating the environmental performance in the most stable not exceeding 1.8kPa.Seismic intensity not impact on insulated parts phase.exceeding 8 degree. which weakens the voltagewithstanding capacity, ensuring Utilize advanced importedAmplitude of electromagnetic the vacuum interrupter suitable testing equipment, exactlyinterference induced in for harsh environment. record no-load mechanicalsecondary system not characteristics of each product,exceeding 1.6kV. E2 level electrical life extended and provide users with theseand M2 level mechanical life characteristic curves, ensureextended as per GB1984-2003, product reliability.capacitive current breaking andlowre-breakdown probability C2level, having completed thetype test.Outline dimension anddistribution panel interlockingmethod completely compatiblewith domestically dominantmedium voltage switchgearKYN28, high universality,significantly reduce design cost4E-VAC EP Series Medium Voltage Vacuum Circuit BreakerE-VAC EP Series Medium Voltage Vacuum Circuit BreakerApplication areasChemical industry Substation Oil industry Cement industry Piping industry Automotive industry Offshore mining Power plantShipbuildingTextile and food industries Paper making industry Metallurgical industryOpencast coal mineT echnology creation historyAs the manufacturer of the world’s first vacuum interrupter, the pioneer of vacuum technology, Eaton Electrical has been committed to the research, development andmanufacturing of vacuum interrupters for over 70 years, and gathered plenty of experience. Westinghouse has become the synonym of quality and reliability.We own the world’s largest and globally leading vacuum interrupter plant and the only vacuum interrupter plant that is equipped with large capacity high voltage laboratories.Our manufacturing capacity and design and development always maintain a leadership position.E-VAC vacuum circuit breaker requires almost no relevant maintenanceSimple structure design of E-VAC vacuum circuit breaker further minimizes fault occurrence, simplifies daily maintenance. With the indicator on the circuit breaker panel, no detection instrument isrequired, facilitating the judgment of working state of circuit breaker. The circuit breaker utilizes the world’s first class Eaton Electrical’s vacuum interrupter with vacuum degree up to 10-6Pa, low air leakage, and ensure 50-year life with no maintenance required.Optional accessoriesCharging handle Trolley handle LifterIdeal for control and protection in medium voltage power supply and distribution systemThe circuit breaker is equipped with superior spring chargingmechanism, utilizes modular design, offering optimized mechanism main part distribution, simpler structure and more reliable performance. The whole mechanism is composed by three modules: charging,closing, opening. Assembly and maintenance of these three parts are very simple. The spring charging mechanism composed by ratchet wheel mechanism, oscillator and closing spring is compact and smart. The operating mechanism is usually equipped with manual charging device and electric charging device, enabling automatic reclosing function.The circuit for manual charging operating mechanism is provided with manual opening and closing operation buttons, circuit breaker position indicator and spring mechanism charging status indicator, switch operations counter, shunt release auxiliary switch, position and fault signals, etc..The circuit breaker of electric charging operating mechanism: added with spring charging motor, shunt release, trip free relay, and auxiliary switch for spring charging motor release.The following accessories can also be provided as needed: undervoltage release, overcurrent relay, etc..E-VAC EP Series Medium Voltage Vacuum Circuit Breaker5E-VAC EP Series Medium Voltage Vacuum Circuit BreakerMain specification and technical parametersItem Unit ValueRated voltage kV 12Rated short-time power frequency withstand voltage (1 min) 42 (phase to ground, phase to phase) 48 (gap)Rated lightning impulse withstand voltage (peak) 75 (phase to ground, phase to phase) 85 (gap)Rated frequency Hz 50Rated current A 630 630 1250 1250 1600 1250 16001250 1600 2000 2000 2500 2000 250040002500 2500 3150 3150 (1)4000 3150 (1) Rated short-circuit breaking current kA 25 31.5 40 50Rated short-time withstand current (4s) 25 31.5 40 50125Rated peak withstand current kA 63 80 100 (2)125Rated short circuit making current 63 80 100 (2) Secondary circuit power frequency withstand voltage (1 min) V 2000Opening time ms 20~50Closing time 35~70Mechanical endurance time 30000 (1600A/31.5kA and below), 20000 (2000A and above, 40kA), 10000(50kA) Rated current breaking endurance 30000 (1600A/31.5kA and below), 20000 (2000A and above, 40kA), 10000(50kA) Rated short circuit current breaking endurance time 50 (1600A/31.5kA and below), 30 (2000A and above, 40~50kA)Allowable accumulated wearingthickness of moving/fixed contact mm 3Rated closing operating voltage V AC 110/220 DC 110/220Rated opening operating voltageRated voltage of spring charging motor V AC 110/220 DC 110/220Rated power of spring charging motor W 55~90Charging duration s ≤15Rated operating sequence O-0.3s-CO-180s-CO (40kA and below), O-180s-CO-180s-CO (50kA)Note:(1) Forced air cooling is required at 4000A; (2) For higher parameters, please contact the Eaton Corp.T echnical parameters for trip/close coilsName ParameterRated operating voltage (V) AC, DC110 AC, DC220Rated operating current of close coil (A) 2.0 1.0Rated operating current of trip coil (A) 1.8 (40kA and above is 2.6) 0.9 (40kA and above is 1.6)Normal operating voltage range Closing: 80%~110% of rated operating voltageOpening: 65%~120% of rated operating voltage, opening will not occur when thenormal operating voltage is less than 30% of rated operating voltageE-VAC EP Series Medium Voltage Vacuum Circuit Breaker 6E-VAC EP Series Medium Voltage Vacuum Circuit BreakerOutline and dimension of E-VAC EP circuit breaker (drawout type)Distribution Rated Rated short panelcurrent circuit breaking width (mm) (A) current (kA)P H A B C D E G J K L M N R S T W Q 800 630 25~31.5 210 275 638 652 640 650 433 Φ35 280 598 76 78 637 508 277 40 23 / 800 1250 25~40 210 275 638 652 640 650 433 Φ49 280 598 76 78 637 508 277 40 23 550* 800 1600 31.5 210 275 638 652 640 650 433 Φ55 280 598 76 78 637 508 277 40 23 / 800 2000 40 210 310 638 652 640 650 361 Φ79 295 586 77 88 698 536 277 0 23 550 800 1250~2000 50 210 310 638 652 640 650 361Φ79295 586 77 88 698 536 277 0 19 550 1000 2500 31.5 275 310 838 852 838 850 361 Φ109 295 586 77 88 698 536 377 0 31 / 1000 3150 31.5 275 310 838 852 838 850 361 Φ109 295 586 77 88 725 536 377 0 31 / 10002500~400040~50275310 838 852838 850361 Φ109295586 77 88 725 53637731750**Note：Forced air cooling is required at 4000A. * 40kA only. ** 50kA only.E-VAC EP Series Medium Voltage Vacuum Circuit Breaker7E-VAC EP Series Medium Voltage Vacuum Circuit BreakerOutline and dimension of E-VAC EP circuit breaker (fixed type)E-VAC fixed type vacuum circuit breaker (210 phase space)Rated Rated shortcurrent circuit breaking(A) current (kA) H J E K B N Y1\Y2630~125025~31.527523771.54370555I 12504027523771.54370551II160031.5~4027523771.54370551II 200040310252804493614III1250~200050310252804493614IIIE-VAC EP Series Medium Voltage Vacuum Circuit Breaker 8E-VAC EP Series Medium Voltage Vacuum Circuit BreakerOutline and dimension of E-VAC EP circuit breaker (fixed type)E-VAC fixed type vacuum circuit breaker (275 phase space)Rated Rated short current circuit breaking (A) current (kA)M Z1\Z2 2500 31.5 628 IV 3150 31.5 678 V 2500~400040~50678VE-VAC EP Series Medium Voltage Vacuum Circuit Breaker9E-VAC EP Series Medium Voltage Vacuum Circuit BreakerSecondary control connection diagram of E-VAC EP series vacuum circuit breaker (drawout type) The diagram shows the circuit breaker in test position, opening, discharged statesE-VAC EP Series Medium Voltage Vacuum Circuit Breaker 10E-VAC EP Series Medium Voltage Vacuum Circuit BreakerSecondary control connection diagram of E-VAC EP series vacuum circuit breaker (fixed type) The diagram shows the circuit breaker in opening, discharged states11E-VAC EP Series Medium Voltage Vacuum Circuit BreakerE-VAC EP Series Medium Voltage Vacuum Circuit BreakerE-VAC EP series vacuum circuit breaker selection table1. Circuit breaker models□E-VAC (drawout type)□ E-VAC (fixe d type)2. Parameters of E-VAC EP series vacuum circuit breaker Panel width (mm) Breaker phase Rated short circuit Rated working current (A)spacing(mm) breaking current (kA) □630 □1250 80021025 □630□1250□ 160031.5 □1250 □ 1600 □ 2000 40 □1250 □ 1600□ 2000 501000 275 25 □2500 31.5 □2000□ 2500□ 315040 □1250 □ 1600 □ 2000 □ 2500 □ 3150 □ 4000* □□□ □□□1250 1600 2000 2500 31504000*50* Forced air cooling is required at 4000A.* * The specifications such as the need to purchase, please contact Eaton. 3. Technical parameters of spring operating mechanism Opening power supply (V) □DC110 □ AC110 □ DC220 □ AC220 Closing power supply (V)□DC110 □ AC110 □ DC220 □AC220 Spring charging motor power supply (V)□DC110 □ AC110 □ DC220 □AC2204. Optional configuration (standard option includes trip free device. Please note if the trip free device has to been canceled)□ Overcurrent release □ 2 Overcurrent □ 3 Overcurrent□A□ Closing latch □ V □ Position latch □ V□ Trip free relay □ V □ Undervoltage release □V□ Operating handle□ Quantity neededNote: Technical parameters of products will be changed without notice. Please confirm withEaton corporation before ordering.E-VAC EP Series Medium Voltage Vacuum Circuit Breaker 12•Electrical solutions that use less energy, improve power reliability andmake the places we live and work safer and more comfortable•Hydraulic and electrical solutions that enable machines to delivermore productivity without wasting powerWe deliver:Discover today’s Eaton.•Aerospace solutions that make aircraft lighter, safer and less costly tooperate, and help airports operate more effciently•Vehicle drivetrain and powertrain solutions that deliver morepower to cars, trucks and buses, while reducing fuel consumption and emissionsPowering business worldwideAs a global diversif ed power management company, We provide integrated solutions that help make we help customers worldwide manage the power energy, in all its forms, more practical and accessible. needed for buildings, aircraft, trucks, cars, machinery and businesses.With 2014 sales of $22.6 billion, Eaton has approxi-mately 99,000 employees around the world and sells Eaton’s innovative technologies help customers manage products in more than 175 countries.electrical, hydraulic and mechanical power more reliably, eff ciently, safely and sustainably.Eaton is a power management company with approximately 97,000 employees. The company provides energy-efficient solutions that help our customers effectively manage electrical, hydraulic and mechanical power more efficiently, safely and sustainably. Eaton sells products to customers in more than 175 countries. For more information, visit . Electrical Sector Asia PacificNo. 3 280 Nong Linhong RoadChangning DistrictShanghai, China 200335© 2016 Eaton Corporation Eaton is a registered trademarkAll Rights Reserved of Eaton Corporation.Printed in ChinaE-VAC EP-EN All trademarks are property of theirMay 2016 respective owners.。
西电Eaton W-VACi中高压真空断路器说明书
W-VACi Product portfolio overview
W-VACi vacuum circuit breaker family
Withdrawable
Fixed
12 and 17,5 kV family W-VACi fixed version
472 mm 625 mm 673 mm
1250 A / 31.5 kA
652 mm
Pole space 210 mm
Cubicle width: 800 mm
2000 A / 40 kA
852 mm Pole space 275 mm
Cubicle width: 1000 mm
4000 A* / 50 kA
281 mm 205 mm 281 mm 275 mm 296 mm 310 mm
Westinghouse, Cutler Hammer, MEM, Holec and Moeller • Numerous international patents • Significant R&D investments
Content
• Application areas • W-VACi building blocks • Product portfolio overview • W-VACi frames for 12 kV, 17.5 kV and 24 kV • Full line of accessories • Features & Benefits • Availability
235 mm 205 mm 235 mm 275 mm 248 mm 310 mm 248 mm 310 mm
440 mm
Pole space 150 mm
万能断路器说明书
智能型万能式断路器使用说明书1．概述1.1适用范围HJW1系列空气断路器（以卜简称断路器）主要适用于交流50Hz，额定工作电压为400V、690V，额定电流为400A-6300A的配电网络中，用来分配电能和保护线路及电源设备免受过载、欠电压、短路取和接地等故障的危害。
断路器核心部件采用智能型控制器，具有精确的选择性保护，可避免不必要的停电，提高供电系统的可靠性、连续性和安全性。
1.2型导及其舍义1 3正常的使用，安装和运输条件1.3.1正常使用条件a)周围空气温度上限不超U+40℃，下限不低于-5℃，24h的平均值不超过+35℃，注：在周围空气温度高于+40℃或低-5℃的条件下使用的断路器应与制造厂协商。
b)安装地点的海拔不超过2000m，c)大气的相对湿度在周围最高温度+40℃时不超过50%，在较低在温度下可以有较高的相对湿度（侧如20℃时的90%），并考虑到因温度变化发生在产品表面上的凝露。
1.3.2正常安装条件a)安装位置应垂直、各方向的倾斜度不超过5℃；b)污染等缎：3级c)安装类别：断路器主电路及欠电压脱扣器线圈、电源变压器初级线圈为Ⅳ级，辅助电路、控制电路为Ⅲ级。
1 3 3正常贮存和运输条件a)温度下限不低于-25℃，上限小超过十55℃，b)相对湿度(25℃时)不超过95%，c)产品在运输过程中，应轻搬轻放，小应倒放，应尽量避免剧烈碰撞。
2．技术特征21分类2.1.1按安装方式分：固定式、抽屉式。
2 1 2按操作方式分：电动操作、手动操作。
2 1 3按脱扣器种类：具有智能型控制器、欠电压瞬时（或延时）脱扣器和分励脱扣器。
2 1 4智能型控制器分娄：a) Perfection-L(简称L)型（经济型，光柱显示），h) Perfection-M（简称M）型（普通型，LED数码显示），c) Perfection-H (简称H)型（增强型，LCD液晶显示）。
2.2主要技术参数见表1表1主要技术参数2 .3主要技术性能2.3. l智能型控制器保护特性的电流整定值范围及准确度见表2。
电力断路器参考指南说明书
ContentsDescription Page Table 1. Revision notes (2)Table 2. Breaker catalog number convention ...............................................3Table 3. Symmetrical RMS interruption ratings (kA) for 1-pole breaker frame ......................4Table 4. Symmetrical RMS interruption ratings (kA) for 2-, 3-, and 4-pole breaker frames ............4Table 5. Curve notes ..................................................................4Thermal magnetic trip unit curvesFigure 1. Fixed thermal fixed magnetic single pole 15 A-125 A. .................................5Figure 2. Fixed thermal fixed magnetic two, three, and four pole 15 A-125 A......................6Figure 3. Fixed thermal fixed magnetic DC. ................................................7Figure 4. 240 V peak let through current. .................................................8Figure 5. 240 V peak let through energy...................................................9Figure 6. 480 V peak let through current. .................................................10Figure 7. 480 V peak let through energy. ..................................................11Figure 8. 600 V peak let through current. .................................................12Figure 9. 600 V peak let through energy.. (13)T ime current curves Power Defense MCCB Frame 1 thermal-magnetic2Technical Data TD012063ENEffective November 2019Time current curves Power Defense MCCBFrame 1 thermal-magneticEATON T able 1. Revision notes.ote: NUnless noted below, all curves remain unchanged from their prior revision.3Technical Data TD012063ENEffective November 2019Time current curves Power Defense MCCB Frame 1 thermal-magnetic EATON This information is provided only as an aid to understand the catalog numbers.It is not to be used to build catalog numbers for circuit breakers or trip units as all combinations may not be available.T able 2. Breaker catalog number convention.ote: N IEC standard breakers include the CE mark; GB standard breakersinclude the CCC mark.Poles1 = 1 pole2 = 2 pole3 = 3 pole4 = 4 pole with 100% neutral protection 0 = 4 pole with 0% neutral protectionInterrupting ratingdesignator kA at 480 V (UL)C = 18F = 25G = 35K = 50M = 65N = 85P = 100Continous currentrating0015 = 15 A 0020 = 20 A 0025 = 25 A 0030 = 30 A 0035 = 35 A 0040 = 40 A 0045 = 45 A 0050 = 50 A 0060 = 60 A 0070 = 70 A 0080 = 80 A 0090 = 90 A 0100 = 100 A 0110 = 110 A 0125 = 125 ATerminals includedN = No terminalsJ = Line and load terminals K = Line only terminals L = Load only terminalsTrip unit typeTFF = Fixed thermal / fixed magnetic (non UL)VFF = 50ºC fixed thermal / fixed magnetic (non UL)KNS = Molded case switchBreaker familyPDG1 = Frame 1 Global UL / CSA / IEC / GBPDG1 3 M 0125 TFF J4Technical Data TD012063ENEffective November 2019Time current curves Power Defense MCCBFrame 1 thermal-magneticEATON T able 3. Symmetrical RMS interruption ratings (kA) for 1-pole breaker frame.T able 4. Symmetrical RMS interruption ratings (kA) for 2-, 3-, and 4-pole breaker frames.** Note: 250 Vdc is achieved using 2 poles in series.T able 5. Curve notes.1.These curves apply for 50 Hz and 60 Hz applications.2.The maximum voltage rating for the frame style is stated in Tables 3 & 4.3.These curves are comprehensive for Power Defense style circuit breakers including frame sizes, ratings and constructions stated.4.The total clearing times shown include the response time for the trip unit, the breaker opening and the interruption of the current. The bottom of the time band is the minimum commit to trip time.5.The end of the instantaneous curve is determined by the application or the interrupting rating of the circuit breaker.6.Thermal magnetic trip unit calibration based on 40ºC ambient, cold start. Tested with 4 feet of rated wire (75ºC) per terminal. Tested in open air with current in all poles.7Thermal magnetic trip unit instantaneous calibration based on single pole testing.Technical Data TD012063ENEffective November 2019Time current curves Power Defense MCCB Frame 1 thermal-magnetic CurvesTime current curvesTechnical Data TD012063EN Effective November 2019Time current curves Power Defense MCCBFrame 1 thermal-magneticEATON Time current curves67Technical Data TD012063ENEffective November 2019Time current curves Power Defense MCCB Frame 1 thermal-magnetic EATON Time current curves8Technical Data TD012063ENEffective November 2019Time current curves Power Defense MCCBFrame 1 thermal-magneticEATON Figure 4. 240 V peak let through current. October 20199Technical Data TD012063ENEffective November 2019Time current curves Power Defense MCCB Frame 1 thermal-magnetic EATON Figure 5. 240 V peak let through energy.October 201910Technical Data TD012063ENEffective November 2019Time current curves Power Defense MCCBFrame 1 thermal-magneticEATON 11EATON 12Effective November 2019EATON Figure 9. 600 V peak let through energy. October 201913EATON Eaton1000 Eaton Boulevard Cleveland, OH 44122United States877-ETN-CARE (877-386-2273) © 2019 EatonAll Rights ReservedPrinted in USAPublication No. TD012063EN / TBG001429 November 2019Eaton is a registered trademark.All other trademarks are property of their respective owners.Effective November 2019。
高压电源E型产品说明书
3B SCIENTIFIC ® PHYSICS1Fuente de alta tensión E (230 V, 50/60 Hz) 1013412 Fuente de alta tensión E (115 V, 50/60 Hz) 1017725Instrucciones de uso12/13 SD/ALF1 Ajuste de la alta tensión2 Indicación de la tensión3 Salida de la tensión decaldeo 4 Casquillo de puesta atierra5 Salida de la alta tensión6 Pie soporte abatible7 Interruptor de la red8 Fusibles9 Conmutador de tensión 10 Ventilador1. Aviso de seguridadLa fuente de alta tensión E corresponde a las regulaciones de seguridad para dispositivos eléctricos de medición, de mando, de control y de laboratorio, estipuladas por la norma DIN EN 61010, parte 1, y ha sido montada según la clase de protección I. Está prevista para el servicio en recintos secos, convenientes para los medios de servicio eléctricos.Su uso correcto, acorde con las prescripciones, garantiza el servicio seguro del equipo. Sin embargo, la seguridad no queda garantizada si el dispositivo se usa incorrectamente o se lo manipula sin el cuidado necesario.Si es de suponer que ya no es posible un funcionamiento libre de peligro (por ejemplo, por daños visibles), se debe poner el equipo fuera de servicio inmediatamente.En escuelas e instalaciones educativas, el funcionamiento del equipo debe ser supervisado responsablemente por personal instruido al respecto.•Antes de la primera puesta en marcha, se debe comprobar si el valor impreso en el la-do posterior de la caja corresponde a las exigencias locales de tensión.•Antes de poner en marcha el aparato se debe examinar si existen daños en la caja oen la conexión a la red y, en caso de fallosen el funcionamiento o daños visibles, se debe poner el equipo fuera de servicio ase-gurándolo contra una puesta en marcha in-voluntaria.•El aparato se conecta sólo en enchufes con un conductor de protección conectado a latierra.•Antes de la conexión, revisar si las conexio-nes de experimentación se encuentran libres de daños en el aislamiento o si los cables están pelados.•Los fusibles defectuosos sólo se deben sustituir con uno correspondiente al valor original (ver lado posterior de la caja).•Es necesario desenchufar el aparato antes de cambiar el fusible.•Nunca se debe cortocircuitar el fusible o el portafusibles.•Dejar siempre libres las ranuras de venti-lación de la caja, con el fin de garantizar una suficiente circulación de aire, necesariapara el enfriamiento de los componentes in-ternos.•Sólo un electrotécnico está autorizado a abrir el aparato.2. DescripciónLa fuente de alimentación de alta tensión de Ees una fuente de uso universal, ajustable y librede tierra, para el trabajo con tubos de electrones.Ésta entrega una alta tensión, regulada, ajustable sin saltos, no peligrosa al contacto,con limitación pasiva de corriente. Un trasformador incorporado resistente a altatensión sirve para la toma de la tensión decaldeo para tubos de electrones. Un ventilador termorregulado protege contra el sobrecalentamiento.La fuente de alimentación de tensión 1017725está dimensionada para una tensión de red de115 V (±10 %) resp. 1013412 para 230 V (±10%).3. Datos técnicosTensión de conexióna la red: 115 / 230 V CA ± 10%,ver dorso de la carcasa Frecuencia de la red: 50 / 60 HzProtección por fusible: 115 V: 2x 1 A lento,230 V: 2x 0,5 A lentoAlta tensión: 0 - 5000 V CC, max. 2mATensión decaldeo: 6,3 V CA, max. 3 A,resistente hasta 6 kVProtección de sobrecarga: Primario: fusible, verdorso de la carcasaSecundario: resistenciasde limitación de corriente Contactos: casquillosdeseguridadde 4-mmIndicación: digitalExactitud de indicación: 1% + 2 DigitsTemperatura del medio: de 5 °C hasta 40 °CHumedad relativa max. 80 %Dimensiones: aprox. 240x220x90 mm3Peso: aprox. 2,1 kg4. Servicio4.1 Notas generales•Antes de conectar la fuente de alimentación,el ajuste de alta tensión se lleva a 0(extremo izquierdo).•Se interconecta el montaje experimental conla fuente de alimentación.23B Scientific GmbH ▪ Rudorffweg 8 ▪ 21031 Hamburgo ▪ Alemania ▪ Se reservan las modificaciones técnicas © Copyright 2013 3B Scientific GmbH• Se conecta la fuente de alimentación sólocuando el montaje experimental ya esté listo. • Cambios el montaje experimental se debenrealizar sólo con el circuito sin corriente. • Con el ajuste de alta tensión se fija ahora la tensión deseada.•Antes de la desconexión de la fuente de alta tensión el ajuste de alta tensión se debe haber retornado a 0 (extremo izquierdo).4.2 Reemplazo de fusibles •Desconecte la alimentación de corriente. Esimprescindible que también desconecte el enchufe de la red.• Se saca el portafusible en la parte traserade la fuente, utilizando un destornillador plano (ver Fig. 1) • Se fija el destornillador del lado del enchufepara aparato frio. • Se remplaza el fusible y se vuelve a insertar el portafuibles.Fig. 1 Reemplazo de fusibles5. Mantenimiento, limpieza, desecho • El aparato debe permanecer en un lugarlimpio, seco y libre de polvo. • Antes de la limpieza el aparato se separadel suministro de corriente. • No se debe usar ningún elemento agresivoni disolventes para limpiar el aparato. • Para limpiarlo se utiliza un trapo suavehúmedo. • El embalaje se desecha en los lugareslocales para reciclaje. •En caso de que el propio aparato se deba desechar como chatarra, no se debe deponer entre los desechos domésticos normales. Se deben cumplir las prescripciones locales para el desecho de chatarra eléctrica.6. Ejemplo de aplicaciónFuncionamiento del tubo de difracción de electronesSe requiere adicionalmente:1 Tubo de difragción de electrones D1013885 1 Soporte de tubos D1008507 Observación: Se puede poner al potencial de tierra, ya sea el ánodo o el cátodo, porque la salida de tensión de caldeo es resistente a la alta tensión.Fig. 2 Funcionamiento del tubo de difracción de electrones。
Green Motion EV智能断路器充电器安装指南说明书
Installation guide:EV direct connect and junction box kitsGreen MotionEV smart breaker chargersScan here forSpanish translations1Installation Guide: EV direct connect and junction box kitsEV DIRECT CONNECT AND JUNCTION BOX KITS ContentsPRODUCT INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2–3EV direct connect kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2EV direct connect + junction box kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2EV smart breaker charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3PACKAGE CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4EV direct connect kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4EV direct connect + junction box kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4ROUTINE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5–6EV smart breaker charger operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Direct connect wiring example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6LED indicator descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8–16Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8FCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8General reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9EV direct connect and junction box kits installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10–16• Installation overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9• A - Connect EV smart breaker charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11• B - Insert conductors into loadcenter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12• C - Connect EV connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13• D - Connect EV smart breaker charger & EV connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14–15•E - Install the cord management bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16CONNECT TO WI-FI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192Green Motion EV smart breaker chargersEV DIRECT CONNECT AND JUNCTION BOX KITSEV direct connect kitEV direct connect + junction box kitInstalls directly in BR loadcenters or PRL3X panelboards close to where the electric vehicle is parked.Installs directly in BR loadcenters or PRL3X panelboards. Includes a junction box for when the electric vehicle is parked further away.3Installation Guide: EV direct connect and junction box kitsEV DIRECT CONNECT AND JUNCTION BOX KITS EV smart breaker chargerThe EV smart breaker charger isintended for charging plug-in hybrid and all-electric vehicles and is compat-ible with the Society of Automotive Engineers J1772 charging standard.In addition to traditional thermal-magnetic protection, EV smart breaker chargers:• Protect from ground faults and provide automatic reset so no user interaction is needed.• Instruct the vehicle on how much current to draw to keep from overloading the circuit.• Protect users with interlocked power so that power is never available at the connector unless it is plugged into an electric vehicle.4Green Motion EV smart breaker chargersEV DIRECT CONNECT AND JUNCTION BOX KITS Package contentsRequired items not included:• #10 woodscrew 1-1/2 inches long - x45Installation Guide: EV direct connect and junction box kitsEV DIRECT CONNECT AND JUNCTION BOX KITS EV smart breaker charger operationQUICKLAG thermal-magnetic breakerThe EV smart breaker charger contains integral solenoid controlled contacts in series with QUICKLAG™ thermal-magnetic breaker. T he instructions below describe how to operate the main handle of the EV smart breaker charger:• Main handle must be in the ON position to supply power to the load • When breaker trips, handle will move to the center-tripped position • To reset breaker, push handle to OFF position, and then to ON positionGFCI test buttonInitiates a ground fault self-test. Recommended to perform this test when J1772 connector is plugged into the EV.EV charger reset button Resets the EV charger.EV charger status LEDsDisplay status of the EV charger and various fault conditions, if present.Smart breaker display button1 press – Wi-Fi signal strength is displayed on the smart breaker status LEDs and enable BlinkUp™.2 presses – For non-OCPP EV chargers, this will initiate a manual override of any schedules/advance option restrictions and will allow for a single charge session. The3 middle LEDs will flash green to indicate the override was successful.3 presses – If red EV charger status LED is flashing, this action will clear the fault *Smart Breaker Status LEDs will indicate how many button presses are recorded.Smart breaker reset button Reset the Wi-Fi antenna module and regain connectivity or clear any errors that may have occurred during the BlinkUp process.Smart breaker status LEDs LEDs show how loaded the circuit is compared to its capacity. The color of the LEDs will range from off indicating no load or too small ofa load detected. Green indicates a low load, yellow indicates a medium load, and red indicates a high load. If the LEDs are flashing, this indicates that the current exceeds the rating of the smart breaker. When the smart breaker display button is pressed, these LEDs also show the Wi-Fi signal strength.BlinkUp status LED Indicates the status during the BlinkUp process.Thermal-magnetic breaker handle To manually trip or reset the thermal-magnetic breaker.Remote contact indicator Indicates status of secondary contacts (Open: Green / Close: Red).Item DescriptionBlinkUp receiver/network status amber LEDloadcenter bus)breaker handleRemote contacts indicatorThermal-magnetic pole 1Thermal-magnetic pole 2Terminals 1 and 2 (for connection to field wiring)Neutral pigtail (for electronics module power)Terminal 3 (for connection to +12 Vdc)Ground pigtailTerminal 5(for connection to ground)6Green Motion EV smart breaker chargersEV DIRECT CONNECT AND JUNCTION BOX KITS Direct connect wiring exampleEV smart breaker charger and EV connectorEV connector wire color code:1. (GREEN) EV connector ground 2. (ORANGE) J1772 pilot 3. (BLUE) +12 Vdc 4. (BLACK) Line 25. (RED) Line 17Installation Guide: EV direct connect and junction box kitsEV DIRECT CONNECT AND JUNCTION BOX KITS LED indicator descriptions1. Not a valid J1772 State, the EV smart breaker charger will commence charging when prompted to through the EV smart breaker charger application.2. J1772 State D, the ventilation required state, is not supported and will cause the EV smart breaker charger to enter the fault state.3. Cold Load T imeout: Following a complete loss of power during an active charging session, a phenomenon occurs called Cold Load T imeout. When power is restored, there may be a 2–5 minute delay to resume charging per SAE J2894.StateBlink TypeColorEV pole8Green Motion EV smart breaker chargersEV DIRECT CONNECT AND JUNCTION BOX KITS InstallationImportant safety instructionsGrounding instructionsFor a permanently connected productThis product must be connected to a grounded, metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product .REFERENCE THE QR CODE ON THE EV SMART BREAKER CHARGER FOR LATEST DOCUMENTATION AS THEINFORMATION CONTAINED IN THIS MANUAL IS SUBJECT TO CHANGE .This product must be installed in accordance with the National Electrical Code ® (NEC ®) and any applicable local codes . Before installing equipment, check with your local electrical inspector for requirements and information . If you have questions or need assistance, contact a qualified elec-trical contractor .SAVE THESE INSTRUCTIONS .FCCFCC IDThis device complies with part 15 of the FCC rules . Operation is subject to the following two conditions: 1 . This device may not cause harmful interference, and 2 . This device must accept any interference received,including interference that may cause undesired operation .FCC ID: VPYLB1CBIMP003RF radiation exposure statementThis equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment . This equip-ment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body .Canada low-power license exempt radio communication devices (RSS-210)Common information operation is subject to the following two conditions:1. This device may not cause interference, and2. This device must accept any interference, includinginterference that may cause undesired operation of the device .IC: 772CVLB1CDIMP003DefinitionsEVSE —Electric Vehicle Supply Equipment . EVSE is ageneral term used for all of the equipment used to supply electricity to the car .J1772—SAE Recommended Practice for conductive charg-ing of hybrid and electric vehicles . This standard spells out the physical dimensions of the J1772 connector and the pilot communication between the plug-in vehicle and the EVSE .Pilot —The communication signal through the J1772connector . This signal tells both the vehicle and the EVSE when both are ready to charge and how much current is permitted in the circuit . This signal is part of the SAE J1772 standard .SAE —Society of Automotive Engineers . The group that organizes and leads committees of transportation experts to create standards, such as J1772, for the transportation industry .ADA —Americans with Disabilities Act .UL ®—Underwriters Laboratories . UL is an accredited stan-dards developer in the U .S . and Canada .Moving, transporting, and storage instructionsStore the equipment indoors and in its original packaging until it is ready to be installed . Storage temperature should be between –40 °C and +60 °C . Never attempt to lift, move, or carry the equipment by the EV connector cord or power cord . Improper storage or handling may cause damage to the equipment .NEC Article 625 requires that the coupling means of the electric vehicle supply equipment shall be stored or located at a height of not less than 18 inches (450 mm) and not more than 4 ft (1 .2 m) above the floor level for indoor loca-tions and 24 inches (600 mm) above the grade level for outdoor locations .Americans with Disabilities Act requirements to consider for workplace charging installationThe ADA and workplace chargingThe Americans with Disabilities Act (ADA) is a federal civil rights law that prohibits discrimination in public placesagainst individuals with disabilities . As an employer installing plug-in electric vehicle (PEV) charging stations, also known as electric vehicle supply equipment (EVSE), you need to follow special design guidelines to accommodate people with disabilities, as required by the ADA . Although the ADA does not provide design standards for charging station-equipped parking spots, several industry studies and PEV planning guides do . In addition, several plans developed under the U .S . Department of Energy’s (DOE) Clean Cities EV Community Readiness projects describe best practices for installing ADA-compliant charging stations .Best practices for designing ADA-compliant PEV charging stationsWhen designing ADA-compliant PEV charging stations, consider accessibility, ease of use, and safety for disabled drivers, including those using wheelchairs or other assistive equipment . Key considerations include ensuring adequatewebsite:The following sections detail the instructions for various installation options.Failure to follow these instructions may result in nonfunctional and/or unprotected equipment.EV DIRECT CONNECT AND JUNCTION BOX KITS INSTALLATIONConnect EV smart breaker chargerFollow the steps below, in addition with the considerations listed on page 9, in order to ensure proper installation and wiring of the EV smart breaker charger and the EV connector and cordset.EV DIRECT CONNECT AND JUNCTION BOX KITS INSTALLATION Insert conductors into loadcenterEV DIRECT CONNECT AND JUNCTION BOX KITS INSTALLATION Connect EV connectorEV DIRECT CONNECT AND JUNCTION BOX KITS INSTALLATIONConnect EV smart breaker charger & EV connectorEV DIRECT CONNECT AND JUNCTION BOX KITS INSTALLATIONConnect EV smart breaker charger & EV connectorEV DIRECT CONNECT AND JUNCTION BOX KITS INSTALLATION Install the cord management bracketConnect to Wi-FiWi-Fi commissioning and operationAfter the EV smart breaker charger has been successfully installed and power has been restored to the loadcenter or panelboard, the EV smart breaker charger must be commis-sioned . Ensure that a Wi-Fi signal is available where the EV smart breaker charger has been installed .Get started by downloading the Green Motion EV Charger Manager app . Available on IOS and Google Play stores .• Name your charger • Enter your Wi-Fi credentials• Connect your breaker following the steps in the appTo use the EV smart breaker charger with your preferred charge management system, please visit our developer portal (www .Eaton .com/developer) for complete API documenta-tion . Once the integration is complete, download the EM Install app to commission the EVsmart breaker charger .iOS installGoogle Play installTechnical specificationsDescription SpecificationCatalog number GMEV32BR-DC, GMEV32BAB-DC, GMEV32BR-JB, GMEV32BAB-JBElectrical inputInput power7.7 kWInput voltage208-240 VacInput breaker rating40 AElectrical outputPower output7.7 kWOutput voltage208-240 VacOutput amperage32 AConnector SAE J1772Installation Directly installs in an Eaton BR loadcenter or PRL3X panelboardCable length (in feet)25Safety ULInterlocked power protection YesGround fault protection20 mAOvercurrent protection YesYesAutomatic reset afternuisance trip featureRandomized restart on powerYesfailure (delay before chargingresumes after a power failure)Frequency rating60 HzStorage temperature–40 °C to +60 °CAmbient operating temperature–30 °C to +40 °CHumidity0% to 90%, noncondensingkAIC rating10 kAWarranty Seller warrants that the Products manufactured by it will conform to Seller’s applicable specifications and be free from failure due to defects in workmanship and material for three (3) years from the date of original purchase, installation of the Product, or fromthe date of shipment of the Product, whichever occurs first. In the event any Product fails to comply with the foregoing warranty,Seller will, at its option, either (a) repair or replace the defective Product, or defective part or component thereof, F.O.B. Seller’sfacility freight prepaid, or (b) credit Buyer for the purchase price of the Product. All warranty claims shall be made in writing. Sellerrequires all non-conforming Products be returned at Seller’s expense for evaluation unless specifically stated otherwise in writingby Seller. This warranty does not cover failure or damage due to storage, installation, operation or maintenance not in conformancewith Seller’s recommendations, including as set forth in these Terms and Conditions of Sale, and industry standard practice or due toaccident, misuse, abuse, or negligence. This warranty does not cover breach of data or system security, including that of informationtechnology infrastructure, computers, software, hardware, databases, electronic systems (including database management systems),and networks. This warranty does not cover reimbursement for labor, gaining access, removal, installation, temporary power or anyother expenses, which may be incurred in connection with repair or replacement. This warranty does not apply to equipment notmanufactured by Seller. Seller limits itself to extending the same warranty it receives from the third-party supplier, to the extent suchthird party permits assignment of its warranty. For other general terms and conditions of sale, please refer to Eaton’s selling policy25-000.Certifications UL 489—Molded case circuit breakers, molded case switches, and circuit breaker enclosuresUL 2231—These requirements cover devices and systems intended for use in accordance with the National Electrical Code (NEC),ANSI/NFPA 70, Article 625, to reduce the risk of electric shock to the user from accessible parts, in grounded or isolated circuits forcharging electric vehicles. These circuits are external to or on-board the vehicleUL 1998—These requirements apply to non-networked embedded software residing in programmable components performingsafety-related functions whose failure is capable of resulting in a risk of fire, electric shock, or injury to personsUL 2251—Plugs, receptacles, and couplers for electric vehiclesUL 2594—Electric vehicle supply equipmentCSA® C22.2 No. 5—Molded case circuit breakers, molded case switches and circuit breaker enclosuresSAE J1772 2017 Ed.NFPA 70 Article 625FCC Compliant, Part 15Energy Star Level 2 Certified charger19Installation Guide: EV direct connect and junction box kitsEV DIRECT CONNECT AND JUNCTION BOX KITS TroubleshootingWhy is my EV smart breaker not chargingmy EV?Check for any schedules set on the ‘EV smart breaker charger’ or the EV. If you are attempting to charge outside of these ‘schedules’, charging may notoccur. You will have to manually over-ride the schedule to start a new charging session. See Green Motion EV Charger Manager app for instructions.EV smart breaker charger has tripped. How do I reset the breaker?Eaton’s EV smart breaker chargers behave like a standard Eaton BR thermal mag breaker – once tripped, you have to push it to full-off position and then turn it back on.I see a blinking RED LED on the EV connector. What does this mean and how can I resume normal operation?Red LED on the EV connector blinks at two different speeds. One of the blink patterns is half-a-second-ON and half-a-second-OFF. This is an indication of loss of line side power. Please turn the breaker OFF and recheck the line side wiring of the EV smart breaker.The second blink pattern is one-second-ON and one-second-OFF. Thisindicates a fault condition. Refer to the instruction sheet for various possible fault conditions.Why is the yellow LED flashing on the EVpole?This means that the EV is requesting the charger to go into an unsupported state. The LED will stop flashing once a valid and supported request isreceived.Why is my BlinkUp process not successful?Refer to the EM Install app or the Green Motion EV Charger Manager app for additional information on BlinkUp errors and solutions. You can also refer to the installation video under the ‘Resources’ section of the product web page. Why is the charger’s RED LED flashing after GFCI Test button is pushed?The charger entered a permanent fault mode since a GFCI self-test is initiated while the EV connector is not plugged into the EV. Press the ‘smart breakerdisplay button’ three times to clear the fault.Why is my EV smart breaker showing as “NO INTERNET” in my Green Motion EVCharger Manager app.Check to make sure both the mobile device and the EV smart breaker charger have an active internet connection.I unplugged EV connector in the middleof a charge and now the EV charger is notworking.If you were charging outisde of a pre-defined schedule and you unplugged the EV connector, the EV charger will stop charging since the schedule kicks in again. Check for any schedules set on the ‘EV charger’ or the EV. If you areattempting to charge outside of these ‘schedules’, charging may not occur.You will have to manually over-ride the schedule to start a new chargingsession. See Green Motion EV Charger Manager app for instructions.Why does my mobile app say “waiting” while my EV smart breaker charger is already charging the EV?Depending on the Wi-Fi traffic, the mobile app may take few seconds toupdate and show the correct status. If the mobile app continues to shows an incorrect status, check the Wi-Fi connection on your mobile device and the EV smart breaker charger.Condition For more troubleshooting tips, please refer to the Eaton’s knowledge center website.T roubleshooting TipEaton is a registered trademark.All trademarks are property of their respective owners.Eaton 1000 Eaton Boulevard Cleveland, OH 44122United States Eaton .com© 2022 Eaton All Rights Reserved Printed in USA Publication No . IL191009EN (Rev . 05)July 2023。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
7 检查 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ........................... 5
7 1 检查紧固件 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ................................ 5 7 2 操作检查. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ................................. 5 7 3 回路电阻检查 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ............................... 6 7 4 绝缘水平检查 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ............................... 6
8 操作 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ........................... 6
8 1 手动操作. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ................................. 6 8 2 电动储能操作 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ............................... 7 8 3 电动合闸操作 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ............................... 7 8 4 电动分闸操作 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ............................... 7 8 5 联锁. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ................................... 8 8 6 紧急分闸操作 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ............................... 8
Generated by Foxit PDF Creator © Foxit Software For evaluation only.
E H 系列户内高压交流真空断路器 V1 使用说明书
1 概述
Z4S.60 3.M0.1
第 3页 共 3页
E H 系列户内高压真空断路器是三相交流 5H , V1 0 z 额定电压为 3 6 2k 的户内装置, . ~4 V 可 供工矿、企业、发电厂及变电站作电气设施的控制和保护之用。本产 品符 合标 准 G 1 8 -0 3 B 9 4 20《高压交流断路器》、J 3 5《户内高压交流真空断路器》、D4 3 0 B85 L0《1 ～ 3k 5 V户内高压真空断路器订货技术条件》和 I C2 7 -0 ：20 《高压交流断路器》 E 62 1 10 01 的有关规定。 EH V 1系列户内高压真空断路器既可装入手车式开关柜, 也可装入固定式开关柜。该 断路器具有寿命长、维护简单、无污染、无爆炸危险、噪音低等优点, 并且适应于频繁 操作等比较苛刻的工作条件。 2 技术数据 2 1 断路器主要的技术参数，见表 1 . ，表 2 。 表1 序号 1 2 名 称 单位 额定电压 k V 额定绝 1 i 工频耐受电压 mn k V 缘水平 冲击耐受电压( 峰值) 额定电流 额定短路开断电流 额定短路关合电流( 峰值) 额定峰值耐受电流 额定短时耐受电流 电寿命 额定短路电流持续时间 额定操作顺序 机械寿命 额定单个电容器组开断电流 额定背对背电容器组开断电流 A 60 3 2 5 8 0 8 0 2 5 数 1 2 4 2 7 5 15 20 20~ 50 15 10 20 60 20 00 ~ 35 10 20 00 3. 15 4 0 8(0) 010 1010 0(3) 8(0) 010 1010 0(3) 3. 15 4 0 3 0 4 分- . s合分-8 s 合分 0310 200 00 200 00 100 00 60 3 40 0 值
资 料 来 源 编 制 校 核 规格审查 审 定 批 准
标记 处数 更改门 批准文号
Generated by Foxit PDF Creator © Foxit Software For evaluation only.
2 1 断路器主要的技术参数，见表 1 . . . . . . . . . . . . . . . . . . . . . . . . 。 ...................... 3 2 2 断路器装配调整后, . 其机械特性参数应符合表 2 的规定。 . . . . . . . . . . . . . 4 ............. 2 3 断路器的主回路电阻值见表 3 . . . . . . . . . . . . . . . . . . . . . . . . . 。 ....................... 4 2 4储能电机 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . .................................. 2 5 分、合闸线圈的技术数据见表 5. . . . . . . . . . . . . . . . . . . . . . . . . ....................... 6 26 辅助开关的技术数据见表 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . .......................... 6
5 搬运 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ........................... 3
5 1 包装箱的运输 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ............................... 3 5 2 拆除包装箱 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ................................ 3 5 3 室内搬运. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ................................. 4
9 维护 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ........................... 8
9 1 经常性的检查 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ............................... 8 9 2 清洁. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ................................... 8 9 3 润滑. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ................................... 8 9 4 维护时的注意事项 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ............................. 9
3 使用环境要求 . . . . . . . . . . . . . . . . . . . . . . . . ....................... 6 4 产品结构及工作原理 . . . . . . . . . . . . . . . . . . . . . .................... 7
E H 系列户内高压交流真空断路器 V1 使用说明书
Z4S.60 3.M0.1
第 2页 共 2页
6 安装 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ........................... 4
6 1 安装前的检查 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ............................... 4 6 2 安装. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . ................................... 4