DF22B-3DS-7.92C中文资料
xc9572中文资料
ＸＣ９５７２是ＸＩＬＩＮＸ公司生产的一款高性能可编程逻辑器件。
它内含４个３６Ｖ１８功能块，并具有１６００个可用系统门。
其系统结构如图１所示。
从结构上看，ＸＣ９５７２包含三种单元，即宏单元、可编程Ｉ／Ｏ单元和可编程内部连线。
其主要特点如下：●所有可编程管脚间的脚对脚延时均为５ｎｓ；●系统的时钟速度可达到１２５ＭＨｚ；●具有７２个宏单元和１６００个可用系统门；●可编程次数为１００００次；●可采用５Ｖ在线编程和擦除；●拥有强大的管脚锁定能力；●每个宏单元都具有可编程低功耗模式；●未用的管脚有编程接地能力；●提供有编程保密位，可对设计提供加密保护以防止非法读取；●外部Ｉ／Ｏ引脚与３．３Ｖ和５Ｖ兼容。
２ ＨＤＢ３的编解码及实现原理ＨＤＢ３码（三阶高密度双极性码）是基带电信设备之间进行基带传输的主要码型之一。
它的主要特点是易于提取时钟、不受直流特性影响、具有自检能力、连令串小于３个等。
Ｅ１信号是我国和欧洲国家电信传输网一次群使用的传输系统。
Ｅ１信号由３２个６４ｋｂｐｓ的ＰＣＭ话路经过时分复用形成。
ＣＣＩＴＴ建议Ｇ．７０３标准详细规定了ＨＤＢ３码用于Ｅ１信号的标准。
用ＸＣ９５７２实现Ｅ１信号的ＨＤＢ３编解码电路比较简单，而且无需可调整外围电路。
本设计使用了ＰＣ４４封装形式的ＸＣ９５７２可编程逻辑器件共有３０个可编程ＩＯ引脚、６个电源引脚和４个ＪＴＡＧ引脚。
整个设计使用了ＸＣ９５７２器件８０％的容量。
图２所示是其实现电路图。
ＨＤＢ３码是ＡＭＩ（ＡｌｔｅｒｎａｔｅＭａｒｋＩｎｖｅｒｓｉｏｎ）码的改进型。
ＡＭＩ码是用交替极性的脉冲表示码元“１”，用无脉冲表示码元“０”。
为了防止电路长时间出现无脉冲状态，ＨＤＢ３码的编码规则是：当没有４个或４个连续的“０”码时，就按ＡＭＩ码规则编码；当出现４个或４个连续的“０”码时，每４个连续“０”的第一个“０”的变化应视它前面相邻的“１”的情况而定，如果它的前一个“１”的极性与前一个破坏点的极性相反而本身就是破坏点，则４个连续的“０”的第一个仍保持“０”；如果它的前一个“１”的极性与前一个破坏点的极性相同而本身就是破坏点，则第一个“０”改为“１”。
基士得耶c229速印机维修手册
2.5.2 补墨和搅拌机构……………………………………….……………………. 2-40 油墨盒的放置……………………………………………….……………….. 2-40 补墨机构………………………………………………………….………….. 2-40 油墨泵动作次数的检测……………………………………………….…….. 2-40 油墨检测电路版……………………………………………………………... 2-41 拌和油墨的机构……….…………………………………………………….. 2-43 印筒空转机构……………….……………………………………………….. 2-44
2
目录
1. 机构总述…………………………………………………………………………….… 1-1 1.1 规格……………………………………………………………………………… 1-1 1.2 部件及其功能的说明…………………………………………………………… 1-5 1.2.1 机器外部结构…………………………………………………………….. 1-5 1.3 机器内部………………………………………………………………………… 1-6 1.3.1 操作面板…………………………………………………………………... 1-8 1.3.2 指示灯…………………………………………………………………… 1-10 1.4 印刷过程概述………………………………………………………………….. 1-11 1.5 机械部件布局………………………………………………………………….. 1-12 1.6 电气组件布局………………………………………………………………….. 1-13 1.6.1 印刷线路板布局………………………………………………………… 1-13 1.6.2 扫描仪…………………………………………………………………... 1-14 1.6.3 供纸系统………………………………………………………………... 1-14 1.6.4 卸版 压筒及其它…………………………………………………….. 1-15 1.6.5 出纸部………………………………………………………………….. 1-16 1.6.6 制版部………………………………………………………………….. 1-16 1.6.7 印筒部………………………………………………………………….. 1-17 1.6.8 电气组件一览表……………………………………………………….. 1-18 电路板……………………………………………………………………... 1-18 电磁铁……………………………………………………………………... 1-18 开关………………………………………………………………………... 1-18 电机………………………………………………………………………... 1-19 传感器……………………………………………………………………... 1-20 其它…………………………………………………………………………1-21 1.7 驱动布局……………………………………………………………………….. 1-22 1.7.1 概述……………………………………………………………………… 1-23 1.7.2 主驱动…………………………………………………………………… 1-23
2Bxxxx-xxx-3BD中文资料
2B SeriesSPECIFICATIONS STANDARD *SPECIAL ELECTRICALCenter Frequency (Fc)2000 to 9000 Mhz 1000 to 12000 MHz 3dB Relative Bandwidth (% of FC) 3 to 30 2 to 70Number of Sections Available 3 to 10 2 to 14Nominal Impedance 50 Ohms 50 to 300 Ohms Maximum Insertion Loss See Curve See Curve Maximum VSWR 1.5/1 1.3/1Attenuation in the StopbandSee GraphSee Graph Maximum Input Power (Average)(Watts to 10,000 ft.)300 x 3 db BW (MHz)(Loss Factor)(Fc MHz)See StandardMaximum Input Power (Peak)(Watts to 10,000 ft.)1500 x 3 dB BW (MHz)Fc (MHz)See StandardENVIRONMENTAL Shock 5 G's 15 G's Vibration2 G's15 G'sHumidity90% relative100% relative Altitude Unlimited UnlimitedTemperature Range (Operating)-25 to + 50 degreescelsius-54 to + 100 degreescelsiusTemperature Range (Non-Operating)-54 to + 70 degreescelsius-62 to +150 degreescelsiusMECHANICALApproximate Weight in oz.1.7 x L x W 1.0 x L x WMounting Provisions See below Consult FactoryINSERTION LOSS:The Maximum Insertion Loss atcenter frequency is equal to :LF x (N + 0.5) / % 3 dB BW + 0.1Where:LF= Loss Factor, N= Number ofSections% 3dB BW:3dB BW (MHz) x 100divided byCenter Frequency (MHz)Example:A 5 section 2B with a centerfrequencey of 5000 MHz and a 3dBBW of 500 MHz would have,.08 x 5.5 /10 = 4.4 /10 = 0.44 + 0.1= 0.5 dbMECHANICAL SPECIFICATIONSL Dimension = 1.5 inch = (0.5 x No. of Sections) Approx.W Dimension = 2950 / Fc (MHz) + 0.6 inch Approx.Connectors Available On 2B Series:Lark Code Type C DIM.Inches & MM Lark Code Type C DIM.Inches & MM A SMA JACK .375 & 9.5*G N JACK .736 & 18.7BSMA PLUG.507 & 12.9*HN PLUG.819 & 20.8Lark Engineering SD SERIES元器件交易网*C TNC JACK .750 & 19.1S SPECIAL*D TNC PLUG.844 & 21.4* Not recommended for use with this SeriesThe size shown is a standard used by Lark to facilitate a low cost, easily reproducible unit. Should you require another size, please submit all of your requirements-both electrical and mechanical. This will enable Lark Engineering to quote theoptimum design for your application.Lark Engineering SD SERIES元器件交易网STOPBAND SPECIFICATIONSThe graphs on the following pages define the normal specification limits on attenuation Lark bandpass filter series 2B, 3B, and 4B. The minimum level of attenuation in dB is shown as a "number of 3dB bandwidths from centerfrequency".Since the frequency characteristics vary for differing bandwidths, it is necessary to establish specifications for each bandwidth of filter. The different graphs represent various 3dB percentage bandwidths. Intermediate values should be interpolated. The 3dB percentage bandwidth is defined as follows:3dB Bandwidth (MHz) x 100divided byCenter Frequency (MHz)The exact relationship is as follows:1. 3dB Bandwidths From Center Frequency= Rejection Frequency (Mhz) -Center Frequency (Mhz) divided by 3dB Bandwidth (Mhz)Example:Given:2. Center Frequency = 5000 MHz Minimum 3dB Bandwidth = 500 MHzNumber of Sections = 5Find: Minimum attenuation levels at 4250 MHz and 5800 MHz.3dB BW's from Fc = 4250 - 5000 / 500 = - 1.5and 5800 - 5000 / 500 = + 1.6The answer can be read directly from the 10% graph. Using the 5 section curve at the point -1.5 (4250 MHz) we find the minimum level of attenuation is 40dB.At +1.6 (5800 MHz) the minimum level of attenuation is 50dB.For special requirements, please contact our Application EngineeringDepartment.STOPSP3.HTM元器件交易网STOPBAND SPECIFICATIONSSTOPBAND SPECIFICATIONSSTOPSP3.HTM元器件交易网STOPBAND SPECIFICATIONS。
DF7-3S-3.96C中文资料
3.96 mm Pitch Miniature Connectors for Internal Power Supplies (UL,C-UL and TÜV Listed)
DF7 Series
Complete Locking Function
Completely enclosed locking system
UL/C-UL
TÜV
Item
11. Contact resistance 12. Insulator resistance 13. Withstanding voltage 14. Insertion-Extraction force (per contact) 15. Durability (mating/unmating) 16. Vibration 17. Shock 18. Humidity
8.Cost Effective Tooling
The same crimping tools are used to terminate socket and pin contacts.
9. Prevention of Short Circuits between Adjacent Contacts
6 Applicable Conductor
1618: AWG 16 to AWG 18 2022: AWG 20 to AWG 22 2426: AWG 24 to AWG 26
7 Packaging
SCF: Socket contacts / Reel SC: Socket contacts / Bag PCF: Plug contacts / Reel PC: Plug contacts / Bag
2. Increased Contact Retention of Crimped Contacts and Prevention of Incomplete Insertion
Kinco FD2(S)系列伺服驱动器使用手册
目录目录 (I)第一章产品确认与型号说明 (1)1.1产品确认 (1)1.1.1产品确认事项 (1)1.2产品各部分名称 (2)1.2.1FD2S系列伺服驱动器各部分名称 (2)1.2.2伺服电机各部分名称 (2)第二章使用事项与安装要求 (3)2.1注意事项 (3)2.2环境条件 (3)2.3安装方向与间距 (3)第三章FD2S系列伺服驱动器接口及连线 (5)3.1FD122驱动器接口及连线介绍 (5)3.1.1FD122驱动器接口介绍 (5)3.1.2FD122驱动器外部接线图 (6)3.1.3FD122驱动器端口接线定义 (7)3.1.3.1总线接口（X1） (8)3.1.3.2通讯接口（X2） (8)3.1.3.3I/O接口（X3） (8)3.1.3.4编码器输入接口（X4） (9)3.1.3.5电机电源输入接口（X5） (10)3.2FD2S系列伺服驱动器接口及连线介绍 (10)3.2.1FD2S系列伺服驱动器接口介绍 (10)3.2.2FD2S驱动器外部接线图 (11)3.2.3FD2S驱动器端口接线定义 (12)3.2.3.1I/O接口定义（X1） (13)3.2.3.2逻辑电源和抱闸输入输出接口（X2） (13)3.2.3.3电机电源输入接口（X3） (13)3.2.3.4总线接口（X4） (14)3.2.3.5通讯接口（X5） (14)3.2.3.6编码器输入接口（X6） (14)第四章KINCO伺服上位机调试软件 (16)4.1软件安装 (16)4.2PC与FD2S驱动器通讯 (16)4.2.1RS232通信 (16)4.2.2CANopen通信 (16)4.3操作界面 (17)4.3.2计算机菜单 (17)4.3.3驱动器菜单 (19)4.3.3.1基本操作 (19)4.3.3.2控制环 (19)4.3.3.3I/O口 (21)4.3.3.4工作模式 (21)4.3.3.5数据字典 (22)4.3.3.6驱动器配置 (22)4.3.3.7ECAN (22)4.3.3.8示波器 (24)4.3.3.9实时错误 (26)4.3.3.10历史错误 (26)4.3.3.11控制面板 (27)4.3.3.12初始化/保存 (27)4.3.3.13驱动器属性 (27)4.3.4电机菜单 (27)4.3.5扩展功能菜单 (28)4.3.5.1读驱动器配置步骤 (28)4.3.5.2写驱动器配置步骤 (30)4.4建立新工程一般步骤 (31)第五章电机配置与试运转操作 (34)5.1电机配置 (34)5.1.1FD2S系列伺服驱动器按键操作配置电机 (34)5.1.2FD2S系列伺服驱动器上位机操作配置电机 (35)5.2EASY USE使用说明（用于设置重要参数和自整定） (36)5.3试运转操作 (44)5.3.1试运转操作目的 (44)5.3.2试运转操作注意事项 (44)5.3.3试运转最小系统 (44)5.3.3.1连接编码器电缆到驱动器 (44)5.3.3.2连接电机电缆(带或不带抱闸)到驱动器 (44)5.2.3.3连接逻辑电源和抱闸电源线到驱动器 (44)5.3.3.4编码器信号检查 (45)5.2.3.5给驱动器提供动力电源 (45)5.3.4试运转操作步骤 (45)5.3.4.1数字操作面板操作步骤 (45)5.3.4.2Kinco伺服上位机调试软件操作步骤 (46)第六章工作模式 (47)6.1位置模式（“1”模式） (47)6.2速度模式（“-3”和“3”模式） (47)6.2.2模拟输入控制 (48)6.2.2.1模拟速度模式参数列表 (49)6.2.2.2模拟速度模式操作实例 (50)6.3转矩模式（“4”模式） (52)6.3.1通讯控制 (52)6.3.2模拟输入控制 (53)6.3.2.1模拟力矩模式参数列表 (53)6.3.2.2模拟力矩模式操作实例 (54)6.4脉冲模式（“-4”模式） (56)6.4.1脉冲模式参数介绍 (58)6.4.1.1电子齿轮比 (58)6.4.1.2脉冲模式选择 (58)6.4.1.3脉冲滤波系数 (59)6.4.2脉冲模式操作实例 (59)6.4.2.1驱动器参数设置 (59)6.4.2.2运行结果 (61)6.5原点模式（“6”模式） (62)6.7自动翻转 (62)6.7.1自动翻转参数列表 (63)6.7.2自动翻转操作实例 (63)第七章控制性能 (65)7.1电流环 (65)7.2速度环 (66)7.2.1速度环参数列表 (66)7.2.2速度环比例增益调节 (66)7.2.3速度环积分增益调节 (68)7.2.4速度环反馈滤波调节 (70)7.2.5速度环带宽计算 (70)7.3位置环 (71)7.3.1位置环参数列表 (71)7.3.2位置环比例增益调节 (71)7.3.3位置环速度前馈调节 (73)7.3.4位置环加速度前馈 (75)7.3.5平滑滤波 (75)7.4震动抑制 (78)第八章通讯功能 (79)8.1RS232通讯 (79)8.1.1RS232接线说明 (79)8.1.2RS232通讯参数列表 (80)8.1.3RS232自由传输协议 (80)8.1.4.1下载 (81)8.1.4.2上传 (83)8.2RS485通讯 (84)8.2.1RS485接线说明 (84)8.2.2RS485通讯参数列表 (84)8.2.3MODBUS RTU通讯协议 (85)8.2.3.1Modbus RTU通讯协议基本格式 (85)8.2.3.2Modbus常用功能码简介 (85)8.3CAN OPEN总线通讯 (86)8.3.1CANopen总线通讯硬件说明 (87)8.3.2CANopen总线通讯软件说明 (88)8.3.2.1EDS说明 (88)8.3.2.2SDO说明 (88)8.3.2.3PDO说明 (90)8.3.2.4PDO COB-ID说明 (90)8.3.2.5FD2S系列伺服驱动器支持的COB-ID (91)8.3.2.6保护方式/监督类型说明 (92)8.3.2.7启动过程说明 (92)8.3.3CANopen总线通讯参数列表 (94)第九章报警排除 (95)9.1报警信息 (95)9.2报警信息原因及排除 (95)附录一FD2S系列伺服驱动器参数列表 (97)参数列表：F000组（设置驱动器指令） (97)参数列表：F001组（设置实时显示数据） (98)参数列表：F002组（设置控制环参数） (100)参数列表：F003组（设置输入输出及模式操作参数） (103)参数列表：F004组（设置电机参数） (107)参数列表：F005组（设置驱动器参数） (109)附录二常见负载惯量计算 (112)附录三原点模式介绍 (115)附录四FD2S伺服驱动器与F1系列PLC通讯方法 (120)1软硬件需求 (120)2安装F1-PLC TARGET文件 (120)3建立工程一般步骤 (122)3.1新建工程 (122)3.2PLC配置 (124)3.3设置通讯参数 (125)1FD2S系列伺服驱动器与F1PLC利用CAN OPEN总线进行通讯 (129)2FD2S伺服与P EAK CAN利用CAN OPEN总线进行通讯 (133)2.1通讯连接 (133)2.2报文列表 (135)附录六RS485串口通讯范例 (137)1FD2S系列伺服驱动器与KINCO触摸屏M ODBUS协议通讯 (137)1.1注意事项 (137)1.2触摸屏控制单台FD2S伺服 (137)1.2.1硬件接线 (137)1.2.2通讯参数设置 (137)1.2.3地址参数设置 (138)1.3触摸屏控制多台FD2S伺服 (139)1.3.1硬件接线 (139)1.3.2参数设置 (139)2伺服驱动器与串口调试工具M ODBUS协议通讯 (140)2.1硬件连接 (140)2.2驱动器参数设置 (140)2.3驱动器控制 (140)2.4报文格式 (141)3伺服驱动器与西门子S7-200M ODBUS协议通讯 (142)3.1硬件接线 (142)3.2通讯参数设置 (142)3.3程序编制 (143)3.4范例程序说明 (143)附录七RS232串口通讯范例 (144)1伺服与KINCO触摸屏自由协议通讯 (144)1.1注意事项 (144)1.2触摸屏控制单台伺服驱动器 (144)1.2.1硬件接线 (144)1.2.2通讯参数设置 (144)1.2.3地址参数设置 (145)1.3触摸屏控制多台伺服驱动器 (146)1.3.1硬件接线 (146)1.3.2参数设置 (146)2伺服驱动器与串口调试工具自由协议通讯 (147)2.1硬件连接 (147)2.2通讯参数设置 (147)2.3驱动器控制 (147)2.4报文格式 (149)附录八常用对象工程单位与内部单位换算关系表 (151)附录九常用对象列表 (152)1模式及控制（0X6040） (152)2测量数据 (153)3目标对象（0X607A） (154)4多段位置/多段速度（0X2020） (154)5性能对象（0X6065） (155)6原点控制（0X6098） (156)7速度环参数（0X60F9） (156)8位置环参数（0X60FB） (156)9输入输出口参数（0X2010） (156)10脉冲输入参数（0X2508） (158)11用于存储的参数（0X2FF0） (159)12错误代码（0X2601） (159)附录十制动电阻规格选择 (161)附录十一保险丝规格选择 (162)第一章产品确认与型号说明首先，感谢您使用Kinco伺服系统产品，Kinco系列不同型号驱动器的配件各不相同，建议您对产品进行确认。
DX7s中文
注意Horizon Hobby 全权拥有更改所有操作指南、保修，及其他相关资料之权限。
如需要最新产品资讯，请登录/Prodinfo/Files/SPM7700-manual.pdf注意事项：产品资料中的以下事项为操作此产品可能造成的不同程度浅在危险：注意：若不照程序适当操作，可能会造成有形财产的损失，以及可能对人造成轻微伤害。
警示：若不照程序适当操作，可能会造成有形财产的损失，以及可能对人造成严重伤害。
警告：若不照程序适当操作，可能会造成有形财产损失、间接伤害，以及可能对人造成严重伤害，或极有可能造成外伤。
警告：在操作此产品前，请仔细阅读整本操作手册，以熟知产品特性。
操作产品不正确，可能对产品及个人财产造成损失，也可能对人造成严重伤害。
这是精密的模型产品而非玩具。
操作时必须谨慎，并且要有常识及基本机械能力。
未能以安全和负责的态度操作此产品，会导致受伤，或产品及其他财产的损失。
在无成人监督下，儿童不宜使用本产品。
请别尝试拆解本产品，也请勿在无Horizon Hobby的允许下，使用不相符的零件或进行改装。
说明书包含安全使用说明、操作和保养。
在组装或使用前，阅读及遵循使用手册的说明和警告是必要的，以正确操作并避免损坏及受伤。
警告：请不要购买仿冒品感谢您购买正版Spektrum产品。
Horizon Hobby能提供您正版高质量的Spektrumt产品。
Horizon Hobby并不提供支持及保修给仿冒品，也不负责仿冒品的兼容性及性能。
另外，一些声称与DSM2或Spektrum兼容的产品也不具有Horizon Hobby的支持及保修。
保修注册请登录注册您的产品箱内物品清单. DX7S发射机.SD记忆卡.12V直流电源.8通道SPMAR8000接收机（纯发射机版本不含）.SPM6803公/母对频插头.使用说明书（快速入门指南）.2.0mm L型六角扳手.挂绳.装饰贴纸目录快速入门指南---------------------------------------------------------------------4为发射机充电--------------------------------------------------------------------------------------------6 NiMH/ Lipo电池支持-----------------------------------------------------------------------------------------6 发射机功能--------------------------------------------------------------------------------------------------7对频--------------------------------------------------------------------------------------------------------------8 发射机的使用--------------------------------------------------------------------------------------------------8 天线-----------------------------------------------------------------------------------------------------------8主界面----------------------------------------------------------------------9界面导航----------------------------------------------------------------------------------------------------10 系统属性设定-------------------------------------------------------------------------------------------10 用户名---------------------------------------------------------------------------------------------------10 对比度---------------------------------------------------------------------------------------------------10 操作模式------------------------------------------------------------------------------------------------11 区域-------------------------- ---------------------------------------------------------------------------11 语言------------------------------------------------------------------------------------------------------11 固定翼/直升机设置------------------------------------------------------------------------------------11系统设定---------------------------------------------------------------------------------------------------13 记忆模组-----------------------------------------------------------------------------------------------13 机种选择-----------------------------------------------------------------------------------------------13 记忆模组名称-----------------------------------------------------------------------------------------13 开关功能设定-----------------------------------------------------------------------------------------13 记忆模组重置-----------------------------------------------------------------------------------------13 记忆模组复制-----------------------------------------------------------------------------------------13 报警设定-----------------------------------------------------------------------------------------------14 遥测功能------------------------------------------------------------------------------------------------14 制式设定/响应速度-----------------------------------------------------------------------------------15 固定翼--------------------------------------------------------------------------------------------------------15 翼型-----------------------------------------------------------------------------------------------------15 副翼分动系统-----------------------------------------------------------------------------------------15 副翼系统-----------------------------------------------------------------------------------------------15直升机-------------------------------------------------------------------------------------------------------16 飞行模式-----------------------------------------------------------------------------------------------16 油门.螺距和翼尾曲线-------------------------------------------------------------------------------17 陀螺仪--------------------------------------------------------------------------------------------------17电子调速器--------------------------------------------------------------------------------------------17飞行模式-----------------------------------------------------------------------------------------------17十字盘------------------------------------------------------------------------------------------------17功能菜单----------------------------------------------------------------------------------------------------17舵机设置-----------------------------------------------------------------------------------------------17大小舵角&线性指数---------------------------------------------------------------------------------18熄火开关------------------------------------------------------------------------------------------------18遥控距离/发射机功率测试--------------------------------------------------------------------------19计时器---------------------------------------------------------------------------------------------------20全通道舵量监控---------------------------------------------------------------------------------------21教练功能-------------------------------------------------------------------------------------------------21失控保护--------------------------------------------------------------------------------------------------21Smart Safe失控保护-------------------------------------------------------------------------------22 最后指令位置失控保护-----------------------------------------------------------------------------22预设失控保护----------------------------------------------------------------------------------------22接收器和舵机设置---------------------------------------------------------------------------------------23接收机安装-------------------------------------------------------------------------------------------23舵机安装----------------------------------------------------------------------------------------------24舵机使用守则-----------------------------------------------------------------------------------------24电力系统需求-----------------------------------------------------------------------------------------24电力系统建议指南-----------------------------------------------------------------------------------24附录--------------------------------------------------------------------------------------------------------25操作模式转换----------------------------------------------------------------------------------------25锂电发射机电池-------------------------------------------------------------------------------26舵机控制----------------------------------------------------------------------------------------------27检修指南---------------------------------------------------------------------------------------------------27零件清单---------------------------------------------------------------------------------------------------29快速入门指南1．安装主接收机汽油与硝基燃料引擎固定翼：用保护泡棉把主接收机包好，并用橡皮筋，或钩子、挂绳将之固定住。
MIL-C-22992中文资料
Code 32 MIL-C-229926-44207M3XX-XXXXX212M4XX-XXXXX212M5XX-XXXXXBraided AdaptersAvailable in:AmericasEuropeAsia Pacificsss6-45Order Shell Max. Entry ALeft Hand Thd.Dimensions No.Size Size, Type 1*Class 2B C Max. D Max. E Max 121208.750-20 UNEF 29.0 [1.14]25.4 [1.00]33.5 [1.32]141410.875-20 UNEF 29.7 [1.17]25.9 [1.02]35.3 [1.39]161612 1.000-20 UNEF 30.0 [1.18]26.2 [1.03]37.1 [1.46]181814 1.125-18 UNEF 30.7 [1.21]26.9 [1.06]38.6 [1.52]202016 1.250-18 UNEF 31.2 [1.23]27.7 [1.09]40.1 [1.58]222218 1.375-18 UNEF 32.0 [1.26]28.2 [1.11]41.7 [1.64]242422 1.625-18 UNEF 33.5 [1.32]30.0 [1.18]46.5 [1.83]282824 1.875-16 UN 34.8 [1.37]31.2 [1.23]49.8 [1.96]323228 2.062-16 UNS 36.3 [1.43]32.5 [1.28]52.8 [2.08]363628 2.312-16 UNS 37.6 [1.48]33.8 [1.33]56.1 [2.21]4040282.625-16 UN38.9 [1.53]35.3 [1.39]58.9 [2.32]*For larger than maximum type 1 entry sizes, a two-piece adapter will be supplied. Contact Tyco Electronics for information.Table of DimensionsEntry Dimensions Size Z ± 0.20 (± 0.51)YDia. Min.W Max.03 4.75 [.187]9.98 [.393]39.6 [1.56]04 6.35 [.250]11.58 [.456]39.6 [1.56]057.92 [.312]13.08 [.515]42.9 [1.69]069.53 [.375]14.76 [.581]42.9 [1.69]0711.13 [.438]16.33 [.643]46.0 [1.81]0812.70 [.500]17.91 [.705]—0914.27 [.562]17.91 [.705]49.3 [1.94]1015.88 [.625]21.11 [.831]49.3 [1.94]1117.48 [.688]22.68 [.893]52.3 [2.06]1219.05 [.750]24.21 [.953]52.3 [2.06]1320.62 [.812]24.21 [.953]55.6 [2.19]1422.23 [.875]27.46 [1.081]55.6 [2.19]1523.83 [.938]29.03 [1.143]59.9 [2.36]1625.40 [1.000]30.61 [1.205]59.9 [2.36]1828.58 [1.125]35.08 [1.381]69.6 [2.74]2031.75 [1.250]38.25 [1.506]72.6 [2.86]2234.93 [1.375]41.43 [1.631]75.9 [2.99]2438.10 [1.500]44.60 [1.756]79.0 [3.11]2844.45 [1.750]50.90 [2.004]85.3 [3.36]Entry Size DimensionsBraided Adapters(continued)6-46Spin-Coupling AdaptersBase Dimensions Part Shell AY Z Number Size L.H. Thread Class 2B± .020 (±0.51)Min.1212.750-20 UNEF 20.24 [.797]12.47 [.491]1414.875-20 UNEF 23.44 [.923]14.35 [.565]1616 1.000-20 UNEF 26.42 [1.040]17.53 [.690]1818 1.125-18 UNEF 31.17 [1.227]18.19 [.716]2020 1.250-18 UNEF 34.49 [1.358]21.72 [.855]2222 1.375-18 UNEF 37.21 [1.465]25.02 [.985]2424 1.625-18 UNEF 42.82 [1.686]30.48 [1.200]2828 1.875-16 UN 50.06 [1.971]36.58 [1.440]3232 2.062-16 UNS 55.35 [2.179]40.77 [1.605]3636 2.312-16 UNEF 61.01 [2.402]52.96 [2.085]4040 2.625-16 UNS 67.46 [2.656]57.15 [2.250]44442.875-16 UNS70.66 [2.782]62.46 [2.549]*For larger than maximum type 1 entry sizes, a two-piece adapter will be supplied.Contact Tyco Electronics for information.Table of Dimensions204M3XX-XXXMolded Part Size Selection Guide (Spin-Coupling)Uniboot PartsNo.No.(Min.)12202C63212.7 [0.50]14, 16202C64217.5 [0.69]18, 20, 22, 24202C65322.4 [0.88]Available in:AmericasEuropeAsia Pacificsss6-47Tinel-Lock AdaptersTXR32XX00-XXXXXXTXR32XX90-XXXXXXTXR32XX45-XXXXXXDimensionsOrder Shell Max. Entry AC D E Z S Y W No.Size Size Type ILeft Hand Thd Max.Max.Max.+ .010Dia.± .015Max.Class 2B - .020(± 0.38)121208.750-20 UNEF 29.0 [1.14]25.4 [1.00]33.5 [1.32]19.05 [.750]22.28 [.877]26.67 [1.050]52.3 [2.06]22.02 [.867]141410.875-20 UNEF 29.7 [1.17]25.9 [1.02]35.3 [1.39]22.23 [.875]25.46 [1.002]29.84 [1.175]55.6 [2.19]25.17 [.991]161612 1.000-20 UNEF 30.0 [1.18]26.2 [1.03]37.1 [1.46]25.40 [1.000]28.63 [1.127]33.02 [1.300]59.01 [2.36]28.34 [1.116]181814 1.125-18 UNEF 30.7 [1.21]26.9 [1.06]38.6 [1.52]28.57 [1.125]31.81 [1.252]36.19 [1.425]69.6 [2.74]31.52 [1.241]202016 1.250-18 UNEF 31.2 [1.23]27.7 [1.09]40.1 [1.58]31.75 [1.250]34.98 [1.377]39..37 [1.550]72.6 [2.86]34.69 [1.366]222218 1.375-18 UNEF 32.0 [1.26]28.2 [1.11]41.7 [1.64]34.93 [1.375]38.15 [1.502]42.55 [1.675]75.9 [2.99]37.79 [1.488]242422 1.625-18 UNEF 33.5 [1.32]30.0 [1.18]46.5 [1.83]38.10 [1.500]41.33 [1.627]45.72 [1.800]79.0 [3.11]40.97 [1.613]282824 1.875-16 UN 34.8 [1.37]31.2 [1.23]49.8 [1.96]————323224 2.062-16 UNS 36.3 [1.43]32.5 [1.28]52.8 [2.08]————363624 2.312-16 UNS 37.6 [1.48]33.8 [1.33]56.1 [2.21]————4040242.625-16 UN38.9 [1.53]35.3 [1.39]58.9 [2.32]————**For larger than maximum type 1 entry sizes, a two-piece adapter will be supplied. Contact Tyco Electronics for information.Available in:AmericasEuropeAsia Pacificsss6-48CRES-Lock Adapters Code 32 Band Strap AdapterNotes:1. This product is designed to terminate a braided cable shield by means of a band strap and a heat shrinkable lipped boot to a connector.2. See CH00-0250-016 for ordering information, modifications and additional dimensions.3. See drawing BND-XX25S for band strap dimensions and information.4. Adapter to be permanentlymarked with code identification number and full part number (e.g.06090-BND32AB00-1812). Band strap shall bear no part marking.5. All entry sizes are shown in Table II. Maximum entry sizes are ass h o w n in Table I. For larger entry sizes than the maximum, a Type II adapter may be supplied. See CH00-0250-016 for further details.6. Adapter mates to: MIL-C-22992,Class C and R, MS17343, 44, 45and 47 Connectors.7. Anti-rotational set screw, 3 threaded holes 120° ± 5° apart,single mating set screw supplied:AN565DC4H2. Not required for Type II adapters.For additional codes available,contact TycoElectronics.Straight AdapterCode 0045° Adapter Code 45Type II Modification(See Note 5)90° Adapter Code 90Available in:AmericasEuropeAsia Pacificsss6-49CRES-Lock Adapters Code 32 Band Strap Adapter (Continued)Table IOrder Shell Entry Size Ø AØ B C D F Number Size 2Max.Unified Thread Max.Max.Max.Max.Type I 1Class 2B 1212080.7500–20 UNEF 27.229.028.436.61.07 1.14 1.12 1.441414100.8750–20 UNEF 30.229.728.938.41.19 1.17 1.14 1.51161612 1.0000–20 UNEF 33.530.029.240.11.32 1.18 1.15 1.58181814 1.1250–18 UNEF 36.630.730.041.71.44 1.21 1.18 1.64202016 1.2500–18 UNEF 39.931.230.743.21.57 1.23 1.21 1.70222218 1.3750–18 UNEF 42.932.031.244.71.69 1.26 1.23 1.76242422 1.6250–18 UNEF 52.633.533.049.52.07 1.32 1.30 1.95282826 1.8750–16 UN 58.934.834.352.82.32 1.37 1.35 2.08323230 2.0625–16 UNS 65.336.335.655.92.57 1.43 1.40 2.20363634 2.3125–16 UNS 71.637.636.859.22.82 1.48 1.45 2.334040342.6250–16 UN78.038.938.462.03.071.531.512.441. All entry sizes are shown in Table II. Maximum entry sizes are as shown in Table I. For larger entry sizes than the maximum, a Type II adapter may be supplied. See CH00-0250-016 for further details.2. Adapter mates to: MIL-C-22992, Class C and R, MS17343, 44, 45 and 47 Connectors.Table IIEntry Ø Z Ø S Ø Y E Size +0.25/-0.50±0.51±0.38Max.[+0.010/-0.020][±0.020][±0.015]03 4.757.9211.1028.30.1880.3120.438 1.1204 6.359.5212.7029.30.2500.3750.500 1.15057.9211.1214.3030.00.3120.4380.563 1.18069.5212.7015.8830.80.3750.5000.625 1.210711.1214.3017.5031.50.4380.5620.689 1.240812.7015.8819.0532.30.5000.6250.750 1.270914.3017.5020.6533.30.5620.6880.813 1.311015.8819.0522.2334.00.6250.7500.875 1.341117.5020.6523.8035.00.6880.8120.938 1.381219.0522.2325.4035.80.7500.875 1.000 1.411320.6523.8327.0036.00.8120.938 1.063 1.421422.2325.4030.1637.50.8751.0001.1891.48Table II (Continued)Entry Ø Z Ø S Ø Y E Size +0.25/-0.50±0.51±0.38Max.[+0.010/-0.020][±0.020][±0.015]1523.8327.0031.7537.8.0938 1.062 1.250 1.491625.4028.5833.3438.31.000 1.125 1.313 1.511828.5831.7536.5139.81.125 1.250 1.438 1.572031.7534.9039.6941.31.250 1.375 1.563 1.632234.9038.1042.8643.01.375 1.500 1.688 1.692438.1041.2846.8344.51.500 1.625 1.844 1.752641.2844.4549.6146.31.625 1.750 1.953 1.822844.4547.6352.7848.31.750 1.875 2.078 1.903047.6550.8056.3650.01.875 2.000 2.219 1.973250.8054.0059.5351.52.000 2.125 2.344 2.033454.0057.1562.7153.32.1252.2502.4692.10。
实创兴SEW270模块用户技术手册V2.0
2
SEW270 WCDMA 模块
前言
概述
本文档适用的产品是：实创兴 SEW270 模块。本文档通过对 SEW270 模块的介绍，用以指导用户 对该模块进行硬件设计并获取软件技术支持，并在该模块基础上更方便快捷的进行各种终端无线产品 的设计。
阅读对象
本文档主要适用于以下工程师： � � � � � 系统设计工程师 结构工程师 硬件工程师 软件工程师 测试工程师
内容简介
本文档包含 5 章，内容如下： 章节 1 概述 2 产品介绍 3 引脚描述 4 硬件接口描述 5 结构 内容 介绍 SEW270 模块的基本技术规格、参考涉及的相关文档和缩略语。 简要介绍 SEW270 模块的电路原理图和应用方框图。 介绍 SEW270 模块引脚名称和功能。 介绍 SEW270 模块各部分的硬件接口参考设计。 介绍 SEW270 模块的外观图、装配图、天线连接器规格和模块固定方式。
侵权必究。 实创兴电子保留修改本手册技术参数及规格的权力，对本手册中的印刷错误及与最新资料不符之处我 们 会及时改进。所有这些改动不再事先通知，但会编入新版手册中。 实创兴电子拥有本手册的最终解释权。
1
SEW270 WCDMA 模块
实创兴是国内领先的移动通讯企业，以数据卡、移动手持终端、无线通讯模块解决方案为主营业务， 可为 WCDMA/EDGE/cdma2000 等通讯模块用户提供技术支持。 实创兴电子为客户提供现场、电话、网站、即时通讯、E-MAIL 等多种支持方式。 实创兴电子网站 ，提供相关的行业信息和模块相关技术资料。 全国技术支持您想获得实创兴电子产品的技术支持信息，您可以进入在线帮助，通过网络的方式与技 术支持进行交流。如有疑问可发送邮件至 support_Module@ 来获得技术支持。 技术支持热(2012-07-28) 第一次正式发布。 V2.0(2012-9-8) 修改 UIM 卡接口电路，修改模块复位功能实现方式，更新规格参数表。
Panamax MD2-C产品说明说明书
CAUTION!All Panamax Warranties and Connected Equipment Policies are valid only in the United States and Canada.CAUTION!Audio/Video, computer and/or telephone system installations can be very complex systems, consisting of many interconnected components.Due to the nature of electricity and surges, a single protector may not be able to completely protect complex installations. In those cases, a systematic approach using multiple protectors must be employed. Systematic protection requires professional design. AC power, satellite cables, CATV cables, telephone/network lines, signal lines or any other electrical conductors, entering the system that do not pass through this surge protector may invalidate the Panamax Connected Equipment Protection Policy. For additional information on how to protect your system, please contact Panamax before connecting your equipment to the surge protector.CAUTION!WARRANTY LIMITATION FOR INTERNET PURCHASERSPanamax products purchased through the Internet do not carry a valid Product Warranty or Connected Equipment Protection Policy unless purchased from an Authorized Panamax Internet Dealer and the original factory serial numbers are intact (they must not have been removed, defaced or replaced in any way). Purchasing from an Authorized Panamax Internet Dealer insures that the product was intended for consumer use, has passed all quality inspections and is safe. Buying through auction sites or unauthorized dealers may result in the purchase of salvaged, failed and/or products not intended for use in the US. In addition, Authorized Panamax Internet dealers have demonstrated sufficient expertise to insure warranty compliant installations. For a list of Authorized Panamax Internet Dealers go to . If you have any questions regarding these requirements, please contact Panamax Customer Relations.Product Upgrade ProgramIf your Panamax power conditioner sacrifices itself while protecting your connected equipment, you have an option to upgrade to the latest technology. Please go to our web site or contact Panamax Customer Relations at 800-472-5555 for details.Panamax Surge ProtectorLimited LifetimeProduct Warranty Panamax warrants to the purchaser of any standard Panamax surge protector that the surge protector shall be free of defects in design, material, or workmanship, and Panamax will repair or replace any defective unit. For product replacement see “NOTIFICATION” (3).Panamax Surge Protector Limited Connected Equipment Protection PolicyI t is the policy of Panamax that it will, at its election, either replace, pay to replace at fair market value, or pay to repair, up to the dollar amount specified below, equipment that is damaged by an AC power, cable, telephone, or lightning surge while connected to a properly installed Panamax power conditioner. To be eligible for compensation, repair and or replacement, the power conditioner must shows signs of surge dam-age or that it is operating outside of design specifi-cations, relative to its surge protection capability, and under all of the circumstances failed to protect your connected equipment.MD2-C $100,000THE LIMITED CONNECTED EQUIPMENTPROTECTION POLICY IS SUBJECT TO THE FOLLOWING CONDITIONS AND LIMITATIONS 1. ORIGINAL OWNERSHIP REQUIREMENT:2. PROPER INSTALLATION: Panamax AC protectors must be directly plugged into a properly grounded 3-wire AC outlet. Extension cords*, non-grounded two prong adapters, or other non-Panamax surge products must not be used. Building wiring and other connections to protected equipment must conform toapplicable codes (NEC or CEC). No other ground wiresor ground connections may be used. All wires (includ-ing, e.g., AC power lines, telephone lines, signal/datalines, coaxial cable, antenna lead-ins) leading into theprotected equipment must first pass through a singlePanamax protector designed for the particular applica-tion. The protector and the equipment to be protectedmust be indoors in a dry location, and in the samebuilding. Panamax installation instructions and dia-grams must be followed3. NOTIFICATION:You must notify Panamax withinten days of any event precipitating request for prod-uct replacement or payment for connected equipmentdamage. A return authorization (RA) number must firstbe obtained from the Panamax Customer RelationsDepartment at ** before returningthe protector Panamax. At this time, you must notifyPanamax if you believe you have a claim for damagedconnected equipment. Once you obtain an RA number,please mark the number on the bottom of the unit andpack it in a shipping carton/box with enough packingmaterial to protect it during transit. The RA numbermust also be clearly marked on the outside of the car-ton. Ship the unit to Panamax. Please note that you areresponsible for any and all charges related to shippingthe unit to Panamax. If connected equipment damagewas indicated on your RA request, Panamax will mailyou claim kit to be completed and returned within 30days. A connection diagram of your system will berequired as part of the claim kit. Be sure to note itsconfiguration before disconnecting your equipment.4. DETERMINATION OF FAILURE:Panamax willevaluate the protector for surge damage. The Panamaxprotector must show signs of surge damage or mustbe performing outside (>10%) of design specificationsrelative to its surge protection capability. Opening theenclosure, tampering with, or modifying the unit in anyway shall be grounds for an automatic denial yourrequest for payment. Panamax, after evaluating all in-formation provided, will determine whether or not yourrequest is eligible for payment. If the surge protectorshows no signs of AC power or signal line surge dam-age and is working within design specifications, Pana-max will return the unit to you with a letter explainingthe test results and notifying you of the rejection of yourclaim. Exceptions: If a dealer or installer replaces theprotector for the customer, replacement will be re-turned to the dealer installer; or if the protector is apre-1996 model, it will be replaced; or, for a Canadiancustomer, the protector will be replaced. Panamaxreserves the right to inspect the damaged connectedequipment, parts, or circuit boards. Please note thatyou are responsible for any and all charges related toshipping the damaged equipment to Panamax. Pana-max also reserves the right to inspect the customer’sfacility. Damaged equipment deemed uneconomical torepair must remain available for inspection by Pana-max until the claim is finalized.5. REQUEST PAYMENTS: Once Panamax has deter-mined that you are entitled to compensation, Panamaxwill, at its election, either pay you the present fair mar-ket value of the damaged equipment, or pay for thecost of the repair, or send you replacement equipment,or pay the equivalence of replacement equipment.6. OTHER INSURANCE/WARRANTIES: This coverageis secondary to any existing manufacturer’s warranty,implied or expressed, or any insurance and/or servicecontract that may cover the loss.7. EXCLUSIONS: THE PANAMAX CONNECTEDEQUIPMENT PROTECTION POLICY DOES NOTAPPLY TO: Service charges, installation costs, rein-stallation costs; setup cost; diagnostic charges; peri-odic checkups; routine maintenance; loss of use of theproduct; costs or expenses arising out of reprogram-ming or loss of programming and/or data; shippingcharges or fees; service calls; loss or damage occa-sioned by fire, theft, flood, wind, accident, abuse ormisuse, and products subject to manufacturer’s recallor similar event.8. DISPUTE RESOLUTION: Any controversy or claimarising out of or relating to Panamax’s ConnectedEquipment Protection Policy, or the alleged breachthereof, shall be settled by arbitration administered bythe American Arbitration Association under its Com-mercial Arbitration Rules. You may file for arbitrationat any AAA location in the United States upon the pay-ment of the applicable filing fee. The arbitration will beconducted before a single arbitrator, and will be limitedsolely to the dispute or controversy between you andPanamax. The arbitration shall be held in any mutuallyagreed upon location in person, by telephone, or online.Any decision rendered in such arbitration proceedingswill be final and binding on each of the parties, andjudgment may be entered thereon in a court of com-petent jurisdiction. The arbitrator shall not award eitherparty special, exemplary, consequential, punitive, in-cidental or indirect damages, or attorney’s fees. Theparties will share the costs of arbitration (including thearbitrator’s fees, if any) in the proportion that the finalaward bears to the amount of the initial claim.-THE LIMITED PRODUCT WARRANTY IS THE ONLYWARRANTY PROVIDED WITH THIS PANAMAXPRODUCT AND ANY OTHER IMPLIED OR EX-PRESSED WARRANTIES ARE NON-EXISTENT.This warranty may not be modified except in writing,signed by an officer of the Panamax Corporation.* The use of a Panamax extension cord or equiva-lent (UL or CSA listed, minimum 14AWG, 3-wiregrounded) will not invalidate the warranty.** Forms are available on the Panamax web sitefor requesting RAs and opening a claim for con-nected equipment damage.MODEL - MD2-CDOC. NO. IWS00877_EN REV. AEffective Date 1/21/10800-472-5555Panamax’s limited connected equipment protectionpolicy extends to the original purchaser of the Panamax product only and is non-transferable. Original purchase receipts must accompany any product return or claim for connected equipment damage.9. GENERAL: If you have any questions regarding the product warranty or the connected equipment pro- tection policy, please contact the Panamax Customer Relations Department at www.panamax. com.The Limited L i f e t i m e Product Warranty and L i m i t e d Connected Equipment Policy herein super- sede all previous warranties and/or Connected Equip- ment repair/replacement policies.。
FC221系列温控器说明书
产品简介：FC221系列温控器主要用于中央空调采暖和制冷系统。
系统通过检测环境温度与设定温度进行比较产生控制信号，自动调节水阀开度，达到能量供需平衡，同时控制风机的开停状态。
本产品有5个继电器输出，用于控制三速风机及水阀。
电器参数：额定电压：24DC/AC负载电压：<3A测温度范围：1-50℃精度：±1℃（@21℃)输入：外置感温探头（NTC10K),窗磁，房卡，露点探头输出：2路（0-10V)模拟量输出和3路继电器输出工作环境：0-50℃外形尺寸:86*86*50mm注意事项：1、由专业技术人员安装，安装前请确认已经切断电源；2、本产品应安装在空气流通较好的常温环境里，远离热源，远离 门窗避免太阳直射。
3、安装时，不可在温控器上任意打孔，请勿用硬物撞击液晶显示 屏以及用猛力按压显示屏四周，以免液晶屏破裂；4、请严格按照接线图接线，否则有可能损坏温控器。
1、在安装及返修时，一定要确保温控器是处于关机状态；2、用一字螺丝刀插入，轻轻撬动即可分开前后盖，拔下显示板上 的16芯线。
3、将挂板固定在86底盒上；4、将电源板上的16芯线连接到面板上，扣上温控器前盖。
安装步骤：接线图：安装建议/尺寸(MM)GNDCOM GNDESI/DP OCCAC/DC 24Vmax.AC250V/5A12345678910111213141516NTC 10KA BLOMEHI AB(-)(+)功能描述：显示说明：通讯地址码1 (247)工厂默认值1通信接口RS485通信协议Modbus-RTU波特率4800bps/9600bps/19200bps/38400bps 字节8bit 校验码无校验奇校验偶校验工厂默认值工厂默认值无校验Modbus 通信停止位2bit9600bps上键下键开关机键模式键风速键风速等级符号制冷模式符号通风模式符号制热模式符号自动模式符号四段温区符号星期符号modbus通信冷水阀符号热水阀符号露点符号摄氏度符号防冻激活符号华氏度符号门磁符号延时符号按键锁节能符号故障提示符号警示符号内部或外部传感器故障符号管制符号设置温度房间温度WiFi图标时间显示或阀值显示定时开机符号定时关机符号电加热符号来电方式在设备启动期间，版本和类型号会在开始屏幕上短暂显示。
FC21中文资料
Electrical Connection
B E/D S
C
80
G
ID -- VDS
[FET]
80
ID -- VDS
[FET]
Drain Current, ID -- mA
Drain Current, ID -- mA
60
VGS=0
--0.5V
--1.0V
60
VGS=0
--0.5V
40
40
--1.0V
100
ID -- VGS
[FET]
ID -- VGS
[FET]
VDS=10V
VDS=10V IDSS=60mA
Drain Current, ID -- mA
100
80
80
60
60
=7
5m
40
40
ID
40 m
20
Ta =
75
SS
55
--2
A
°C
20
0 --6 --5 --4 --3 --2 --1 0 ITR01963 --6 --5 --4 --3 --2 --1
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
81001 TS IM TA-1526 No.7021-1/5
Parameter [FET] Drain-to-Source Voltage Gate-to-Drain Voltage Gate Current Drain Current Allowable Power Dissipation [TR] Collector-to-Base Voltage Collector-to-Emitter Voltage Emitter-to-Base Voltage Collector Current Collector Current(Pulse) Base Current Collector Dissipation [Common Ratings] Total Dissipation Junction Temperature Storage Temperature PT Tj Tstg 600 150 --55 to +150 mW °C °C VCBO VCEO VEBO IC ICP IB PC 55 50 6 150 300 30 200 V V V mA mA mA mW VDSX VGDS IG ID PD 40 -40 10 75 400 V V mA mA mW Symbol Conditions Ratings Unit
美国H2SCAN公司-产品手册
产品应用
工厂或车间 过程泄漏 分析车间和控制室 储存罐和氢气运输
工业和大学实验室 氢气存储区域和传输管路 工作区域（通风柜和中试设备） 过程气泄漏
技术指标
量程
15ppm～100%（体积）；无需外围设备
性能
工业防护等级 校准周期
IP64 1年
产品寿命 输入输出
输入 /接口
工作温度
10年 锂电池：工作时间10小时；
Capacitance
0.0015%
0.5%
H2 by Volume
产品优势
便携式氢气检漏仪量程：15ppm～100% 固定式氢气监测仪量程：4000ppm～5%（10%～125%LEL） 在线式氢气检测仪量程：0.5%～100% 抗其它气体干扰：CO、CO2、H2S、Cl2、N2、CH化合物、He、NH3；有氧或无氧 快速响应时间：2秒～10秒 介质气体温度：-20℃～100℃；相对湿度：0%～95%RH 对CH4等其它易燃气体无交叉敏感性，可消除误报警 多种输出方式：0～5VDC或4～20mA输出；RS422或RS232接口
产品应用
工厂或车间 过程泄漏 分析车间和控制室 储存罐和氢气运输
工业和大学实验室 氢气存储区域和传输管路 工作区域（通风柜和中试设备） 过程气泄漏
技术指标
量程
体积：0.4%～5.0%（10%～125%LEL）
精度
±（0.03×读数+0.2）百分比
性能
典型响应时间 工业防护等级
<60s IP66
校准周期
季冉实业公司
◆ 便携式氢气检漏仪 ◆ 固定式氢气监测仪 ◆ 在线式氢气分析仪 ◆ S F6红外气体传感器 ◆ CO2红外气体传感器
产品选型手册
PC929中文资料
g TÜV ( VDE 0884 ) approved type is also available as an option.
s Features 1. Built-in IGBT shortcircuit protector circuit 2. Built-in direct drive circuit for IGBT drive
V
VCC = V01 = 24V, RG = 47Ω
6.5 6.0 5.5
CG = 3 000pF, FS = OPEN
1
2
3
V
(9)
*9
O2 "High→Low" delay time at protection from overcurrent
tPCOHL
Ta = 25˚C
-
4
10
µs
O2 fall time at protection from overcurrent
Amp.
1 2 3 4 5 67
1 Cathode 2 Cathode 3 Anode 4 NC 5 NC 6 NC 7 NC
8 FS
9C
10 GND
11 O2 12 O1 13 VCC 14 GND
Terminals 4 to 7 : Shortcircuit in element
* "OPIC" (Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and signal processing circuit integrated onto a single chip.
mb89f202中文资料
敞末让开端没。没有有使使用用的的I/O输末入端末进端入会输引出起状误态动后作并和把锁其定敞，开造；成如永其久在性输损入害状，态故，请就用按2照kΩ输或入以末上端的的电处阻理上方拉法或处下理拉该末等端I/。O
• N.C. 管脚的处置
（转下页）
6
系列 MB89202
（承上页） 管脚编号
SH-DIP32*1 SSOP34*3
24-27 26-29
21-23 32 10
23-25 34 10
管脚名称
P40/AN0 |
P43/AN3 P70-P72
VCC VSS
16
17
C
, — 16 22 :*1 DIP-32P-M06 :*2 FPT-34P-M03
（转下页）
2
系列 MB89202
（承上页）
产品型号 参数
MB89202
MB89F202
MB89V201
10 位 A/D 转换器 1A通0/D过位转精8换/度1功6×位能8定(个时转通器换道时/ 计间数：器1输2.出16或µ时s/1基2.定5 时MH器z计) 数器连续激活
Wild 寄存器
位8 × 2
：有 ×：无
MB89202 ×
MB89F202 ×
MB89V201 × ×
■ 产品间的差异
• 存储器容量
使用评价产品进行评价之前， 请先确认其与实际使用产品的差异。
• 屏蔽选项
产品不同，可以选择的项目和指定选项的方法也不同。选择之前，请查阅 “■ 屏蔽选项”一览表。
3
系列 MB89202
■ 管脚图
P33/EC
15
N.C.
16
C
DF22系列连接器说明书
DF22-3S-7.92C(28 )DF22R-3EP-7.92C DF22-3P-7.92DSA(05)DF22-2P-7.92DSA(06)DF22L-5P-7.92DSA(05)1■Features1. Rated up to 43ASingle position connector can carry current of 43A with 10 AWG conductor. Please refer to Table #1 for current ratings for multi-position connectors using other conductor sizes.2. P ositive Locking FunctionReliable interior lock protects mated connectors fromaccidental disconnection. (Fig.1)3. Prevention of Incorrect ConnectionsTo prevent incorrect connection when using multiple connectors having the same Number of contacts, 3 product types having different mating configurations are available. (Fig.2)4. Molded-in contact retention tabsHandling of terminated contacts during the crimping is easier and avoids entangling of wires, since there are no protruding metal tabs.5. Prevention of incorrect board placementBuilt-in posts assure correct connector placement and orientation on the board.6. Supports resin sealingAllows potting up to 10mm.7. P revention of Short Circuits BetweenAdjacent ContactsEach Contact is completely surrounded by the housing wall electrically isolating it from adjacent contacts.8. I ncreased Retention Force of CrimpedContactsImproved pull-out force design.9. Full Line of Crimp Socket ContactsHirose has released DF22C-*S-7.92C which has easy to push/release latch design. and DF22B-*S-7.92C/DF22C-*S-7.92C which has improved electrical insulation properties.10. In-line ConnectionsWire-to-wire connection is also available. Space is saved with 2-row (2×2) layout for 4 pos.11. UL, C-UL, and TÜV Certified.Positive LockCompletely enclosedlocking system Protection from shorts circuits between adjacent contactsDF22 Series7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)Fig.112. Glow Wire compliance (Compliant with IEC 60695-2-11)O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .2DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)lines, please factor in your own safety margin.Note 2 : Includes temperature rise caused by current flow.Note 3 : The storage condition refers to long-term storage of the product on the shelf before assembly. Please use the operatingtemperature for temporary storage such as pre-assembly and during shipping.DF22 B L - 2 S - 7.92 C (**)●Socket, Header DF22 A - 1416 SCF A●Contactsqqi!1o!0wertyuNumber of contacts : 1 to 5Contact pitch : 7.92 mm Type of housing C : Crimp housing DSA : Straight header DS : Right-angle header No letter : RetainerConnector typeS : Socket DS : Double-row socket P : Header EP : In-line plugDEP :Double-row in-line plug RS/P : Retainer Series name : DF22Guide key type Blank : Inside (Color: natural)R : Right side (Color: black)L : Left side (Color: red)Form TypeSocketsBlank :Standard height, standard lock (Type I) B : Long type, standard lock (Type III) C : Long type, ergonomic lock (Type IV) In-line PlugsBlank : With panel stop A : Without panel stop Applicable CableBlank : UL1430 A : UL1015Applicable Conductor 1416 : 14 to 16 AWG 1012 : 10 to 12 AWG Plating specifications Blank : Tin plated A : Gold platedPackaging SCF : Socket contacts / reel SC : Socket contacts / pack PCF : In-line plug contacts / reel PC : In-line plug contacts / pack q i o !1!0w e r t y u ■Product Number StructureRefer to the chart below when determining the product specifications from the product number.Please select from the product numbers listed in this catalog when placing orders.O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .3DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)Note 1 : Bag packaging (100 pcs/pack). Order by number of packs.Note 2 : Every even number position has a different locking design.■ Type IHeight : Standard type, Standard lockNote : The part number and HRS No. have changed to reflect theproduct form change of the 2 to 5 pos. types.Shown with terminated and contacts installed.Shown with terminated and contacts installed. ■Crimp Sockets (Standard Height Type) O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .4DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)■ Type IIIHeight : Long type, Standard lock ■ Type IVHeight : Long type, Enhanced ergonomic lockShown with terminated and contacts installed.Type 4Height : Long type, user-friendly operation(12.75)14.52387.7No. of contacts indicatorCavity No.Type 1 Pos.Shown with terminated and contacts installed.■Crimp Sockets (Height, Long Type)Note 1 : Bag packaging (100 pcs/pack). Order by number of packs.Note 2 : Every even number position has a different locking design.Note 1 : Bag packaging (100 pcs/pack). Order by number of packs.Note 2 : Every even number position has a different locking design.O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .5DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)B Recommended PCB Layout(Board thickness : 1.6±0.1)Cavity No.No. of contacts indicator10.82.30.89.31.54.0512.4518.13.710.83.23.23.98.7A11 Pos.2-R 0.52.5+0.1 01+0.18.5+0.1--0.211.1±0.13.4±0.13.2±0.051 Pos.)#(*¤%#%*(#)*¤%#%*¢&#+%#&%E2,#.'¤%#%*7¤%#%*"¢&#,%#&%2 to 5 Pos.■Straight HeaderNote 1 : B ag packaging (100 pcs/pack). Order by number of packs.Note 2 : T ray packaging (150 pcs/tray). Order by number of 150.Note 3 : Every even number position has a different locking design.Note 4 : P lease contact Hirose representative if you have request for non-standard Au plating.[Specification number](05) : T in-copper plated bag packaging (25) : T in-copper plated tray packaging (only 1 pos)(06) : G old plated, bag packagingO c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .6DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)No. of contacts indicatorCavity No.9.312.7234.95A 1B R ecommended PCB Layout(Board thickness : 1.6±0.1)P=7.92±0.05C±0.05B±0.052-Ø1.6+0.1015.2±0.05*-Ø1.5+0.1Note 1 : B ag packaging (100 pcs/pack). Order by number of packs.Note 2 : Every even number position has a different locking design.Note 3 : Please contact Hirose representative if you have request fornon-standard Au plating.Shown with terminated and contacts installed.Shown with terminated and contacts installed.Note 2 : Every even number position has a different locking design.■In-line Plug1 Pos.2, 3 Pos.A No. of contacts indicatorCavity No.Polarity mark10.59.9712.7234.95BContact No.13A123O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .7DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)Note 1 : Please ensure when mating this connectorthat the tapered portions of the panel are facing outward towards the receptacle connector’s mating interface.Note 1 : B ag packaging (100 pcs/pack). Order by number of packs.Note 2 : Every even number position has a different locking design.A 1No. of contacts indicatorCavity No.9.38.1212.7220.734.9516.31 Pos.4.835+0.1 03.5±0.111±0.2(A+0.4)+0.1 0(C-0.5-X)+0.1 010.27+0.1 013.02+0.1■In-line Plug (Panel Lock Type)Shown with terminated and contacts installed.Shown with terminated and contacts installed.O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .8DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)17.2219.0421.7910.57.9220.734.95Cavity No.No. of contacts indicatorPolarity markContact No.112344APanel lock typeWithout panel lock function7.9215.5Contact No.1No. of contacts indicator17.4420.1414.523Polarity markCavity No.(21.29)1324Standard lockB R ecommended Panel Cutout (Panel mount type)11±0.219.76+0.1 0(23.72-X)+0.1 06.3±0.19.62+0.119.34+0.122.09+0.1 017.62+0.1 0■In-line Double-row SocketNote : Bag packaging (100 pcs/pack). Order by number of packs.Shown with terminated and contacts installed.Shown with terminated and contacts installed.Note : Bag packaging (100 pcs/pack). Order by number of packs.Note 1 : Please ensure when mating this connector that the tapered portions of the panel are facing outward towards the receptacle connector’s mating interface.O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .9DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)A 3.2B211.67.92No. of contacts indicatorCavity No.A543213.2A B7.928.62No. of contacts indicatorCavity No.2341A5■RetainerFor Standard height, standard lock (Type I)For Long type, standard lock (Type III)Long type, enhanced ergonomic lock (Type IV)packs.Note 1 : Bag packaging (100 pcs/pack). Order by number of packs.Note 2 : When connecting retainer into the plug housing, pleasenote the cavity numbers will line up numerieally, but the retainer cavity numbers will be upside down compared to the plug cavity numbers.O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .10DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)Note 1 : The conductor of applicable wire is tin plated annealed copper.Note 2 : When using other than the applicable wire, contact your nearest Hirose representative.Note 3 : Strip length : 3.5 to 4.5mm■Crimp Contact for Socket1.61.52.71.41730.8Ø1.5t=0.32.83.84.7P=15.520.821.8170.84Ø23.8P=16.5 2.84.71.42.91.31.6t=0.4For 14 to 16 AWGFor 10 to 12 AWGNote 1 : The conductor of applicable wire is tin plated annealed copper.Note 2 : When using other than the applicable wire, contact your nearest Hirose representative.Note 3 : Strip length : 3.5 to 4.5mm1.63.825.20.8329Ø1.5P=15.50.82.84.7t=0.31.42.71.51.61416■ Crimp Contact for In-line PlugO c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .11DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)B M ated Dimensions●Socket to Straight Header Connection1 Pos.2 to 5 Pos.● S ocket to Right Angle Header Connection● S ocket to In-line Plug (Panel lock type) Connection●Socket to In-line Plug Connection● I n-line Double-row socket to In-line Double-row Plug (Panel lock type) Connection● I n-line Double-row socket to In-line Double-row Plug Connection(25.7)(28.7)(13.5)(12.45)DF22--*RS/P--7.92DF22B/C--*RS/P--7.92DF22#--*S--7.92C(28)DF22#--*P--7.92DSA(**)(23.7)DF22B#--*S--7.92C DF22C#--*S--7.92CDF22#--*P--7.92DSA(**)(26.7)(25.7)(28.7)(13.5)(12.45)DF22--/1RS/P--7.92DF22B/C--1RS/P--7.92(26.7)DF22B#--1S--7.92C DF22C#--1S--7.92CDF22#--1P--7.92DSA(**)(23.7)DF22#--1S--7.92C(28)DF22#--1P--7.92DSA(**)(31.6)(34.6)(12.25)(13.3)DF22--*RS/P--7.92DF22B/C--*RS/P--7.92DF22#--*S--7.92C(28)DF22#--*P--7.92DS(**)DF22#--*P--7.92DS(**)DF22B#--*S--7.92C DF22C#--*S--7.92C(32.6)(29.6)(40.55)(44.55)DF22B/C--*RS/P--7.92DF22--RS/P--7.92DF22B/C--*RS/P--7.92DF22B/C--*RS/P--7.92(43.55)(47.55)(13.0)(14.2)DF22A#--*EP--7.92CDF22A#--*EP--7.92CDF22B#--*S--7.92C DF22C#--*S--7.92CDF22#--*S--7.92C(28)(40.55)(44.55)DF22B/C---*RS/P--7.92DF22--*RS/P--7.92C (43.55)(47.55)DF22B/C--*RS/P--7.92DF22B/C--*RS/P--7.92(13.0)(14.2)DF22#--*EP--7.92CDF22#--*EP--7.92CDF22B#--*S--7.92C DF22C#--*S--7.92C DF22#--*S--7.92C(28)(43.55)(43.55)DF22C#--4DS--7.92CDF22A#--4DEP--7.92C(23.3)DF22B#--4DS--7.92CDF22A#--4DEP--7.92C(22.1)(43.55)(43.55)DF22C#--4DS--7.92CDF22#--4DEP--7.92C(23.3)DF22B#--4DS--7.92CDF22#--4DEP--7.92C(22.1)O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .12DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)B ToolsB Contact Extraction■ Contact extraction tool : Flat-bladed screwdriver, 1.4mm blade width ■ Intended crimp Contacts : DF22-1416SC(F), DF22-1416SCFA, DF22A-1416SC(F),DF22A-1416SCFA, DF22A-1012SC(F), DF22A-1012SCFA, ■ Work Method (Housing Cross- Sectional Diagram)1. R efer to the drawing No. 1. I nsert correct size screwdriver in the housing against the molded-in lance. Push down the lance as shown.2. A ssure that the lance is deflected to release the contact and pull- out wire with the crimped contact.Note 1 : When crimping contact DF22A-1012SCF use a press with 3.5 ton min. Note 2 : AP109A type applicators cannot be used with the CM-105C press.Note 3 : Any problems that occur from using tools other than those specifi ed by Hirose, are not covered by warranty.Note 4 : Attachment for Hirose original applicator is required separately. Please contact press manufacturer about the attachment.Note 5 : Applicator manufactured by JAPAN AUTOMATIC MACHINE (J.A.M.). Please access to HP of J.A.M., if you make inquiriesabout the applicator or crimp defect. (URL : http://www.jam-net.co.jp)Note 6 : Please follow the "Crimping quality standards" and "Table of crimping conditions" when crimping contacts.Note : Please do not reuse the reparred housing. Replace it to new one.O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .13DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)B PrecautionsB Current RatingsThe current rating listed in the catalog indicates the allowable current per contact. However, in applications requiring current transmission through all the contacts, about one-third of the listed rating should be applied.When the current rating for the connector is 3A, and the allowable current of the conductor being used is 1A, then rating of 1A will be used for the entire assembly.The connectors should not be mating / unmating when the electrical current is being applied.Hot swap should not be performed.B Usage EnvironmentPlease contact us about use in equipment that is subjected to repetitive high temperature and low temperature environmental conditions.O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .14DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)MEMO :O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .15DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)MEMO :O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .16DF22 Series ●7.92mm Contact Pitch High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.The contents of this catalog are current as of date of 05/2018. Contents are subject to change without notice for the purpose of improvements.2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN TEL: +81-45-620-3526 Fax: +81-45-591-3726USA:HIROSE ELECTRIC (U.S.A.), INC. SAN JOSE OFFICE 2841 Junction Ave, Suite 200San Jose, CA. 95134Phone : +1-408-253-9640Fax : +1-408-253-9641/us/USA:HIROSE ELECTRIC (U.S.A.), INC. DETROIT OFFICE (AUTOMOTIVE)17197 N. Laurel Park Drive, Suite 253, Livonia, MI 48152Phone : +1-734-542-9963Fax : +1-734-542-9964/us/USA:HIROSE ELECTRIC (U.S.A.), INC. BOSTON OFFICE 300 Brickstone Square Suite 201, Andover, MA 01810Phone : +1-978-662-5255USA:HIROSE ELECTRIC (U.S.A.), INC. HEADQUARTERS CHICAGO OFFICE 2300 Warrenville Road, Suite 150, Downers Grove, IL 60515Phone : +1-630-282-6700/us/CHINA:HIROSE ELECTRIC (CHINA) CO., LTD. SHENZHEN BRANCH Room 09-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre, 5002 Shen Nan Dong Road, Shenzhen City, Guangdong Province, 518008Phone : +86-755-8207-0851Fax : +86-755-8207-0873/cn/KOREA:HIROSE KOREA CO.,LTD.143, Gongdan 1-daero, Siheung-si, Gyeonggi-do, 15084, Korea Phone : +82-31-496-7000Fax : +82-31-496-7100http://www.hirose.co.kr/GERMANY:HIROSE ELECTRIC EUROPE B.V. NUREMBERG OFFICE Neumeyerstrasse 22-26, 90411 Nurnberg Phone : +49-911 32 68 89 63Fax : +49-911 32 68 89 69/eu/GERMANY:HIROSE ELECTRIC EUROPE B.V. HANOVER OFFICE Bayernstr. 3, Haus C 30855 Langenhagen, Germany Phone : +49-511 97 82 61 30Fax : +49-511 97 82 61 35/eu/GERMANY:HIROSE ELECTRIC EUROPE B.V. GERMAN BRANCH Schoenbergstr. 20, 73760 ostfildern Phone : +49-711-456002-1Fax : +49-711-456002-299/eu/FRANCE:HIROSE ELECTRIC EUROPE B.V. PARIS OFFICE 130 Avenue Joseph Kessel, Bat E, 78960 Voisins le Bretonneux, France Phone : +33-1-85764886Fax : +33-1-85764823/eu/THE NETHERLANDS:HIROSE ELECTRIC EUROPE B.V.Hogehillweg #8 1101 CC Amsterdam Z-O Phone : +31-20-6557460 Fax : +31-20-6557469/eu/UNITED KINGDOM:HIROSE ELECTRIC EUROPE BV (UK BRANCH)4 Newton Court, Kelvin Drive, Knowlhill, Milton Keynes, MK5 8NH Phone : +44-1908 202050Fax : +44-1908 202058/eu/CHINA:HIROSE ELECTRIC (CHINA) CO., LTD. (SHANGHAI, HEADQUARTERS)18, Enterprise Center Tower 2, 209# Gong He Road, Jing’an District, Shanghai, CHINA 200070Phone : +86-21-6391-3355Fax : +86-21-6391-3335 /cn/CHINA:HIROSE ELECTRIC (CHINA) CO.,LTD. BEIJING BRANCH A1001, Ocean International Center, Building 56# East 4th Ring Middle Road, ChaoYang District, Beijing, 100025Phone : +86-10-5165-9332Fax : +86-10-5908-1381/cn/TAIWAN:HIROSE ELECTRIC TAIWAN CO., LTD.103 8F, No.87, Zhengzhou Rd., Taipei Phone : +886-2-2555-7377Fax : +886-2-2555-7355 /tw/HONG KONG:HIROSE ELECTRIC HONGKONG TRADING CO., LTD.Room 1001, West Wing, Tsim Sha Tsui Centre, 66 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong Phone : +852-2803-5338 Fax : +852-2591-6560/hk/INDIA:HIROSE ELECTRIC SINGAPORE PTE. LTD. DELHI LIAISON OFFICE Office NO.552, Regus-Green Boulevard, Level5, Tower C, Sec62, Plot B-9A, Block B, Noida, 201301, Uttar Pradesh, India Phone : +91-12-660-8018Fax : +91-120-4804949/sg/SINGAPORE:HIROSE ELECTRIC SINGAPORE PTE. LTD.03, Anson Road, #20-01, Springleaf Tower, Singapore 079909Phone : +65-6324-6113 Fax : +65-6324-6123/sg/INDIA:HIROSE ELECTRIC SINGAPORE PTE. LTD. BANGALORE LIAISON OFFICE Unit No-403, 4th Floor, No-84, Barton Centre, Mahatma Gandhi (MG) Road, Bangalore 560 001, Karnataka, India Phone : +91-80-4120 1907Fax : +91-80-4120 9908/sg/MALAYSIA:PENANG REPRESENTATIVE OFFICE73-3-1, Ideal@The One, Jalan Mahsuri, Bayan Lepas Penang, 11950, Malaysia Phone : +604-648-5536 /sg/THAILAND:BANGKOK OFFICE (REPRESENTATIVE OFFICE)Unit 4703, 47th FL., 1 Empire Tower, South Sathorn Road, Yannawa, Sathorn, Bangkok 10120 Thailand Phone : +66-2-686-1255Fax : +66-2-686-3433/sg/O c t .1.2018 C o p y r i g h t 2018 H I R O S E E L E C T R I C C O ., L T D . A l l R i g h t s R e s e r v e d .DF22R-2P-7.92DS (05)DF22L-4DEP-7.92CDF22R-4DEP-7.92CDF22-1P-7.92DSA(05)DF22-1P-7.92DSA(25)DF22-5P-7.92DS(0 6)DF22L-2P-7.92DS(05)DF22L-2P-7.92DS(06)DF22R-1P-7.92DSA(05)DF22R-2P-7.92DSA(05)DF22-3S-7.92C(28 )DF22R-3EP-7.92C DF22-3P-7.92DSA(05)DF22-2P-7.92DSA(06)DF22L-5P-7.92DSA(05)。
通信英语缩略语中英文对照
邻频干扰
ACIR
Adjacent Channel Interference Ratio
邻信道干扰比
ACK
ACKnowledgement
确认
ACL
Asynchronous Connectionless Link
异步无连接
ACLR
Adjacent Channel Leakage Ratio
Adaptive Differential Pulse Code Modulation
自适应差分脉冲编码调制
ADR
Analogue-Digital Recorder
模拟-数字记录器
ADR
Address Digit Receiver
数字地址接收器
ADR
Advisory Route
建议路由
ADR
Analogue Data Recognition
模拟数据识别
ADRC
Automatic Call Distribution Remote Capture
自动呼叫分配（分布）远程截获
ADSL
asymmetric digital subscriber line
不对称数字用户线
ADSL
Asymetric Digital Subscriber Loop
非对称数字用户环路技术
高级实时处理系统
ARQ
Automatic Repeat Request
自动重复请求ቤተ መጻሕፍቲ ባይዱ
ARS
Address Resolution Server
地址解析服务器
ART
Alarm Reporting Telephone
一种聚丙烯酸酯超疏水涂层的制备方法[发明专利]
![一种聚丙烯酸酯超疏水涂层的制备方法[发明专利]](https://img.taocdn.com/s3/m/b3a7186b302b3169a45177232f60ddccda38e6f4.png)
(19)中华人民共和国国家知识产权局(12)发明专利申请(10)申请公布号 (43)申请公布日 (21)申请号 202010905849.9(22)申请日 2020.09.01(71)申请人 淮阴工学院地址 223100 江苏省淮安市洪泽区东七街三号高新技术产业园A12-2（淮阴工学院技术转移中心洪泽分中心）(72)发明人 蔡鹏 刘永涛 李姗姗 倪伶俐 姜孝武 (74)专利代理机构 淮安市科文知识产权事务所32223代理人 廖娜 李锋(51)Int.Cl.C09D 4/02(2006.01)C09D 5/00(2006.01)C08F 222/14(2006.01)C08F 220/24(2006.01)C08F 2/48(2006.01)C09D 135/02(2006.01)C08J 7/04(2020.01)B05D 3/06(2006.01)B05D 5/00(2006.01)B05D 7/02(2006.01)B05D 7/14(2006.01)B05D 7/24(2006.01)D06N 3/04(2006.01)C08L 69/00(2006.01)(54)发明名称一种聚丙烯酸酯超疏水涂层的制备方法(57)摘要本发明涉及高分子涂层材料技术领域，公开了一种聚丙烯酸酯超疏水涂层的制备方法，其特征在于，室温下，将质量比为1：0.01~0.05：0.02~0.05的不含氟丙烯酸酯类单体、含氟丙烯酸酯类单体和自由基光引发剂搅拌混匀后喷涂在基底表面，置于紫外灯下照射预设时间，得到所述聚丙烯酸酯超疏水涂层。
本发明的超疏水涂层性能优点，无需使用有机溶剂、固体颗粒填料，制备工艺简单，可适用于多种不同的基底和大规模生产，具有广阔的市场前景。
权利要求书1页 说明书3页 附图1页CN 112080167 A 2020.12.15C N 112080167A1.一种聚丙烯酸酯超疏水涂层的制备方法，其特征在于，室温下，将质量比为1：0.01~0.05：0.02~0.05的不含氟丙烯酸酯类单体、含氟丙烯酸酯类单体和自由基光引发剂搅拌混匀后喷涂在基底表面，置于紫外灯下照射预设时间，得到所述聚丙烯酸酯超疏水涂层。
FC722芯片使用手册
增强性能低成本M-BUS接口芯片（FC722）1、简介Meter-BUS（简称“M-BUS”）是一种专门用于各种类型仪表、控制装置的远程通信的总线系统。
FC722是专门针对M-BUS通信标准设计生产的仪表总线专用终端收发接口芯片，芯片采用TSSOP8封装，将整个数据发送与接收功能集成于一体，可使用最少的外围元器件实现高可靠性能的终端总线接口。
FC722内部除了符合M-BUS标准的接收发送电路外，还包含一个可调节电源，可为终端提供多达20mA的输出电流。
2、特点◆完全符合M-BUS国际标准和国家标准◆总线电流200uA—3mA连续可设置◆总线电压15V-42V均可适应◆增强的5V稳压输出可提供最大超过20mA输出电流◆TSSOP8封装，最少只需3只外围元件◆300—19200BPS通信速率◆支持UART协议，只在数据传输时总线有效3、应用领域◆智能水表气表热量表抄表◆智能电网自动抄表◆智能家庭控制网络◆消防报警及联动网络◆中央空调控制系统◆智能传感器网络4、应用电路图1.0 FC722典型应用原理图5、管脚描述注释1：VDO输出电流的能力，取决于编程电阻的大小，见图7.0所示。
除去FC722自身要消耗的电流外，其余可由VDO输出；另外，当客户需要短时的大电流输出时，可将RXD拉低，此时VDO的输出电流能力可达20mA。
6、原理框图图2.0 FC722内部结构框图7、工作原理1,主→从此模式下采用电压调制传输数据，总线电流保持不变。
即主机发送的数据码流是一种电压脉冲序列，用+36V 标识逻辑‘1’，用+24V 标识逻辑‘0’。
在稳态时，线路将保持‘1’状态。
如图3.0 所示：图3.0 FC722接收时序图连接在管脚RXC上的电容C RXC的充放电流是不同的，存在以下关系：I SCcharge=I SCdischage/40这个比例关系是独立于数据内容运行任意UART协议所必须的条件（例如，传输采用11位UART协议，当所有数据只有停止位是“1”，其他都是“0”），必须有足够的时间对电容C RXC进行再充电，内部电压比较器TC3检测来自主机的调制电压，并根据电压VIN=SPACE 或MARK来开关正端输出TXD，输出数据给从机。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
10. In-line Connections
Connectors can be ordered for in-line cable connections. In addition, assemblies can be placed next to each other allowing 4 position total (2 ∞ 2) in a small space.
Voltage rating Item 1. Contact resistance 2. Insulator resistance 3. Withstanding voltage
Specification Contact resistance(Initial value): 5 m ohms max. 1000 M ohms min. No flashover or Insulator breakdown 0.3N min., 5N max. Contact resistance of 10 m ohms max. No electrical discontinuity of 1 µs. min. No electrical discontinuity of 1 µs. min. Contact resistance 10 m ohms max. Contact resistance of 10 m ohms max. No deformation of the insulator parts affecting performance 20mV max., 1mA 1000 V DC 2500 V AC for 1 minute
Measured with a steel pin of 1.6 x 0.8 ± 0.002 thickness 30 cycles Frequency 10 to 55 Hz, single amplitude of 0.75 mm, 3 axis, duration of 2 hours Acceleration of 490 m/s2, 11 ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis. Temperature 40ç ± 2ç, 90% to 95% RH, 96 hours (-55ç: 30 minutes➝ 5 to 35ç: 5 minutes➝85ç: 30 minutes➝5 to 35ç: 5 minutes) for 5 cycles Re-flow solder temperature 250ç, for 10 seconds Manual soldering: Soldering iron temperature 300ç, 3 seconds
Each Contact is completely surrounded by the insulator housing electrically isolating it from adjacent contacts.
qL Type (Guide key: left side, Color: red)
sMaterials
Product Sockets Crimp contacts Headers Part Insulator Contacts Insulator Contacts Material Polyamide High conductivity copper alloy Polyamide (Glass reinforced) High conductivity copper alloy Finish Color: Natural white Tin-lead plated Color: Natural beige Tin-lead plated (Note 1) (Note 2) (Note 1) (Note 2) Remarks UL94V-0 ---------UL94V-0 ----------
9. Full Line of Crimp Socket Contacts
Realizing the market needs for multitude of different applications, Hirose has developed several variants of crimp socket contacts and housings. Continuous development is adding different variations. Contact your nearest Hirose Electric representative for latest developments. *The photographs on the left show header (the board dip side), the photographs on the right show the socket (cable side). *The guide key position is indicated in position facing the mating surface of the header.
3. Prevention of Incorrect Connections
To prevent incorrect connection when using multiple connectors having the same Number of contacts, 3 product types having different mating configurations are available.
元器件交易网 NEW
7.92 mm Contact Pitch, High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)
DF22 Series
Complete Locking Function
Completely enclosed locking system
Protection from shorts circuits between adjacent Contacts
sFeatures
1. 30 A maximum current
Single position connector can carry current of 30 A with #10 AWG conductor. Please refer to Table #1 for current ratings for multiposition connectors using other conductor sizes.
Note 1: Current rating of header is 30A (1 pos.) and 25A (2 to 5 pos.) Note 2: Includes temperature rise caused by the current flow. Note 3: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation.
11. Listed by UL, C-UL, and TÜV.
2004.5
ications
Current rating Ratings AWG10 Number of contacts 1 30A 2 25A 3 25A 4 22A 5 22A Specification UL/C-UL TÜV AWG12 25A 20A 20A 18A 18A AWG14 AWG16 20A 15A 18A 15A 18A 15A 15A 13A 15A 13A AC/DC 1000V AC/DC 600V AC/DC 600V Operating temperature range -35ç to 85ç (Note 1) Operating humidity range 20% to 80% Storage temperature range -10ç to 60ç (Note 2) Storage humidity range 40% to 70% (Note 2) UL/C-UL/TÜV UL C-UL TÜV File No. and Recognition No. : E52653 : E52653 : R9950703
6. Supports encapsulation
Connectors can be encapsulated up to 10 mm without affecting the performance.
7. Prevention of Short Circuits Between Adjacent Contacts
Condition
4. Insertion-Extraction force (per contact) 5. Durability (mating/unmating) 6. Vibration 7. Shock 8. Humidity 9. Temperature cycle 10. Resistance to Soldering heat
Prevention of Incorrect Connections qR Type (Guide key: right side, Color: black)
2. Complete Locking Function