VW99000-4_EN_2009-08-01

Overall Requirements for Service Provision within the Framework of
Component Development
Part 4: Technical Engineering Approval (BMG)
Previous issues
VW 01154: 1996-12, 2000-06, 2001-05, 2002-06, 2003-12; VW 99000-4: 2006-10, 2007-10Changes
The following changes have been made as compared to VW 99000-4: 2007-10:
–See Appendix A "Revision Record"
Contents Page
Scope (1)
Definitions (2)
Technical engineering approval .....................................................................................2Referenced documents .. (2)
Change documentation ................................................................................................31234Appendix A Scope
This standard specifies the technical content of the technical engineering approval (BMG).
Overall development requirements are to be taken from Volkswagen standard VW 99000, contents of the planning release from VW 99000-1, contents of the procurement release from VW 99000-2,and contents of the design release (Audi) and engineering release (Volkswagen) from
VW 99000-3.
1 Group Standard VW 99000-4
Issue 2009-08
Class. No.:
01191Descriptors:general requirements, technical engineering approval, component development, component performance
specifications, procurement release, BT-LAH, design engineering, development requirements,
development conditions, development release, design release, performance specifications, planning
release
Check standard for current issue prior to usage.
This electronically generated standard is authentic and valid without signature.
The English translation is believed to be accurate. In case of discrepancies the German version shall govern.Numerical notation acc. to ISO practice.Page 1 of 3
Technical responsibility
Standards Department I/ET-8
Susanne John Tel.: +49-841-89-39659ET/S Drotleff Karla Tel.: +49-5361-9-17975EKTC/4 Gabriela Bochynek EKTC Tel.: +49-5361-9-21698Manfred Terlinden Confidential. All rights reserved. No part of this document may be transmitted or reproduced without prior permission of a Standards Department of the Volkswagen Group.Parties to a contract can only obtain this standard via the B2B supplier platform .
© Volkswagen Aktiengesellschaft VWNORM-2008-12g
Definitions
The following definitions are used for the application of this standard:
0-series
Zero series 3-D
Three-dimensional Technical engineering approval
All changes, adjustments, and coordinative tasks carried out during tool manufacture, testing period,and introduction into standard production must be incorporated into the 3-D CAD data models, into the corresponding drawings, and into the technical bill of materials.
The following prerequisites shall be met for the issuance of the technical engineering approval:–
Design Release (Audi) and Engineering Release (Volkswagen) granted –
Complete drawing data record (according to standard production sampling)–
Obtainment of statutory type approval by the contractor (if required)–
Dimensional and laboratory-generated test reports regarding the testing conditions –
Record of the manufacturing parameters or serial number of such a record –Complete review or partial review of the component trial according to specifications of the pur‐
chaser by the Testing Department of the purchaser.
Conclusion: Technical engineering approval granted by the purchaser.
Referenced documents
The following documents cited in this standard are necessary for application.
In this Section terminological inconsistencies may occur as the original titles are used.
Standards with the titles given in German are either only available in German or may be procured in other languages from the institution issuing the standard.
VW 99000
Overall Requirements for Service Provision within the Framework of Com‐ponent Development VW 99000-1
Overall Requirements for Service Provision within the Framework of Com‐ponent Development; Part 1: Planning Release VW 99000-2
Overall Requirements for Service Provision within the Framework of Com‐ponent Development; Part 2: Procurement Release VW 99000-3Overall Requirements for Service Provision within the Framework of Com‐
ponent Development; Part 3: Design Release (Audi) and Engineering
Release (VW)
2 3 4 Page 2
VW 99000-4: 2009-08
Change documentation
The following changes have been made as compared to the previous issue.The changes in the text are crossed out and/or marked by a gray background:
Table A.1 – Changes as compared to the issue VW 99000-4:2007-10
Table A.2 – Changes as compared to the issue VW 99000-4:2006-10
Change description in Section:
General
Layout changed acc. to new standards layout without changing the content.Appendix A (informative) Page 3
VW 99000-4: 2009-08。