模具专业英语[1]
模具专业术语英语
模具专业术语英语
模具专业涉及许多专业术语，在英语中对应的词汇如下：
1. Mold/Mould: 模具
2. Die: 模具，尤指金属冲压模
3. Cavity: 模穴
4. Core: 模芯
5. Runner: 喷嘴，注塑道
6. Gate: 浇口，进料口
7. Ejector Pin: 顶针，用于将制品从模具中推出
8. Injection Molding: 注塑成型
9. Blow Molding: 吹塑
10. Compression Molding: 压缩成型
11. Extrusion Molding: 挤出成型
12. Casting: 铸造
13. Hot Runner: 热流道系统
14. Cooling Channel: 冷却通道
15. Draft Angle: 脱模锥度
16. Shrinkage: 收缩率
17. Surface Finish: 表面处理/光洁度
18. Undercut: 模具槽，模具凹槽
这些词汇在模具制造和加工过程中经常使用，涵盖了模具设计、制造和加工等方面的专业术语。
模具英语专业术语
模具英语专业术语上内模：cavity insert模具述语下内模：core insert一、入水：gate行位（滑块）：slide进入位：gate location 镶件：insert水口形式：gate type 压座/斜鸡：wedge大水口：edge gate 耐磨板/油板：wedge wear plate细水口：pin-point gate 压条：plate水口大小：gate size 撑头: support pillar转水口：switching runner/gate 唧嘴：sprue bushing唧嘴口径：sprue diameter挡板：stop plate 二、流道: runner 定位圈：locating ring热流道：hot runner,hot manifold锁扣：latch 热嘴冷流道: hot sprue/cold runner 扣鸡：parting lock set唧嘴直流: direct sprue gate推杆：push bar圆形流道：round(full/half runner 栓打螺丝：S.H.S.B流道电脑分析：mold flow analysis顶板：eracuretun流道平衡:runner balance 活动臂：lever arm 热嘴：hot sprue 分流锥：spure sperader热流道板：hot manifold水口司:bush发热管：cartridge heater 垃圾钉：stop pin探针: thermocouples 隔片：buffle插头：connector plug 弹弓柱：spring rod 插座：connector socket 弹弓:die spring密封/封料：seal中托司：ejector guide bush 三、运水：water line中托边：ejector guide pin 喉塞：line lpug 镶针：pin喉管：tube 销子：dowel pin塑胶管：plastic tube 波子弹弓：ball catch快速接头：jiffy quick connector plug/socker 喉塞: pipe plug四、模具零件：mold components 锁模块：lock plate三板模：3-plate mold斜顶：angle from pin 二板模：2-plate mold斜顶杆：angle ejector rod边钉/导边：leader pin/guide pin 尼龙拉勾：parting locks边司/导套：bushing/guide bushing 活动臂：lever arm 中托司：shoulder guide bushing 复位键、提前回杆：early return bar中托边L：guide pin 气阀：valves顶针板：ejector retainner plate 斜导边：angle pin托板：support plate 术语：terms螺丝：screw 承压平面平衡：parting surface support balance管钉：dowel pin 模排气：parting line venting 开模槽：ply bar scot 回针碰料位：return pin and cavity interference内模管位：core/cavity inter-lock模总高超出啤机规格：mold base shut hight顶针：ejector pin 顶针碰运水：water line interferes withejector pin司筒：ejector sleeve 料位出上/下模：part from cavith (core) side司筒针：ejector pin 模胚原身出料位：cavity direct cut on A-plate,core direct cut推板：stripper plate on B-plate.缩呵：movable core,return core core puller 不准用镶件：Do not use (core/cavity) insert扣机（尼龙拉勾）：nylon latch lock用铍铜做镶件：use beryllium copper insert斜顶：lifter 初步（正式）模图设计：preliinary (final) mold design模胚（架）：mold base 反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers模具加热器/冷却器Mold polishing/texturing模具打磨/磨纹Mold repair模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force 锁模力mould locking force 挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half 上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam 滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床V ertical driller超声波清洗机Ultrasonic clearing machine compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线upper plate上模板blanking下料lower plate下模板stamp letter冲字(料号) die pad下垫板shearing剪断die holder下夹板tick-mark nearside正面压印die set下模座tick-mark farside反面压印bottom block下垫脚冲压名称类bottom plate下托板(底板) extension dwg展开图stripping plate内外打(脱料板)procedure dwg工程图outer stripper外脱料板die structure dwg模具结构图inner stripper 内脱料板material材质lower stripper下脱料板material thickness料片厚度零件类factor系数punch冲头upward向上insert入块(嵌入件) downward向下deburring punch压毛边冲子press specification冲床规格groove punch压线冲子die height range适用模高stamped punch字模冲子die height闭模高度round punch圆冲子burr毛边special shape punch异形冲子gap间隙bending block折刀weight重量roller滚轴total wt.总重量baffle plate挡块punch wt.上模重量located block定位块五金零件类supporting block for locationinner guiding post内导柱定位支承块inner hexagon screw内六角螺钉air cushion plate气垫板dowel pin固定销air-cushion eject-rod气垫顶杆coil spring弹簧trimming punch切边冲子lifter pin顶料销stiffening rib punch = stinger 加强筋冲子eq-height sleeves=spool等高套筒ribbon punch压筋冲子pin销reel-stretch punch卷圆压平冲子lifter guide pin浮升导料销guide plate定位板guide pin导正销sliding block滑块wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模) 汪军锋制作***********************feature die公母模female die母模(凹模)。
模具英语
模具专业英语入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口： switching runner/gate唧嘴口径： sprue diameter二、流道: runner热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate 圆形流道：round(full/half runner流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴： hot sprue 热流道板：hot manifold发热管：cartridge heater 探针: thermocouples插头： connector plug 插座： connector socket密封/封料： seal三、运水：water line 喉塞：line lpug喉管：tube塑胶管：plastic tube 快速接头：jiffy quick connectorplug/socker四、模具零件： mold components三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing中托司：shoulder guide bushing 中托边L：guide pin顶针板：ejector retainner plate 托板： support plate螺丝： screw 管钉：dowel pin开模槽：ply bar scot 内模管位：core/cavity inter-lock顶针： ejector pin 司筒：ejector sleeve司筒针：ejector pin 推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base 上内模：cavity insert下内模：core insert 行位（滑块）： slide镶件：insert 压座/斜鸡：wedge耐磨板/油板：wedge wear plate 压条：plate撑头: support pillar 唧嘴： sprue bushing挡板：stop plate 定位圈：locating ring锁扣：latch 扣鸡：parting lock set推杆：push bar 栓打螺丝：S.H.S.B顶板：eracuretun 活动臂：lever arm分流锥：spure sperader 水口司:bush垃圾钉：stop pin 隔片：buffle弹弓柱：spring rod 弹弓:die spring中托司：ejector guide bush 中托边：ejector guide pin镶针：pin 销子：dowel pin波子弹弓：ball catch模具成形不良用语英汉对照aberration 色差 atomization ?化 bank mark ?料纹 bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜 low hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡 burn mark 糊斑burr 毛边 camber 翘曲cell 气泡center buckle 表面中部波皱 check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷 color mottle 色斑resin wear 树脂脱落 riding 凹陷corrosion 腐蚀 crack 裂痕sagging 松垂 saponification 皂化crazing 碎裂 crazing 龟裂scar 疤痕 scrap 废料deformation 变形 edge 切边碎片scrap jam 废料阻塞 scratch 刮伤/划痕edge crack 裂边 fading 退色scuffing 深冲表面划伤 seam 裂痕filler speak 填充料斑 fissure 裂纹shock line 模口挤痕 short shot 充填不足flange wrinkle 凸缘起皱 flaw 刮伤shrinkage pool 凹孔 sink mark 凹痕flow mark 流痕 galling 毛边skin inclusion 表皮折叠 straightening 矫直glazing 光滑 gloss 光泽streak 条状痕 surface check 表面裂痕grease pits 污斑 grinding defect 磨痕surface roughening 橘皮状表皮皱折 surging 波动haircrack 发裂 haze 雾度sweat out 冒汗 torsion 扭曲incrustation 水锈 indentation 压痕warpage 翘曲 waviness 波痕internal porosity 内部气孔 mismatch 偏模webbing 熔塌 weld mark 焊痕mottle 斑点 necking 缩颈whitening 白化 wrinkle 皱纹nick 割痕 orange peel 橘皮状表面缺陷plate mark 模板印痕 pock 麻点overflow 溢流 peeling 剥离pock mark 痘斑 resin streak 树脂流纹pit 坑 pitting corrosion 点状腐蚀re-entrant mold 倒角式模具 sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套 single cavity mold 单腔模具accurate die casting 精密压铸 powder forming 粉末成形calendaring molding 压延成形 powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形 rocking die forging 摇动锻造compound molding 复合成形 rotary forging 回转锻造compression molding 压缩成形 rotational molding 离心成形dip mold 浸渍成形 rubber molding 橡胶成形encapsulation molding 注入成形 sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming ?泡成形 sinter forging 烧结锻造forging roll 轧锻 six sides forging 六面锻造gravity casting 重力铸造 slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸 swaging 挤锻hot forging 热锻 transfer molding 转送成形injection molding 射出成形 warm forging 温锻investment casting 精密铸造 matched die method 对模成形法laminating method 被覆淋膜成形 low pressure casting 低压铸造lost wax casting 脱蜡铸造 matched mould thermal forming 对模热成形模冲压模具—零件类冲压模具－模板类punch冲头top plate上托板（顶板）insert入块(嵌入件)top block上垫脚deburring punch压毛边冲子punch set上模座groove punch压线冲子punch pad上垫板stamped punch字模冲子punch holder上夹板round punch圆冲子stripper pad脱料背板special shape punch异形冲子up stripper上脱料板bending block折刀male die公模(凸模)roller滚轴feature die公母模baffle plate挡块female die母模(凹模) located block定位块upper plate上模板supporting block for location lower plate下模板定位支承块die pad下垫板air cushion plate气垫板die holder下夹板air-cushion eject-rod气垫顶杆die set下模座trimming punch切边冲子bottom block下垫脚stiffening rib punch = stinger 加强筋冲子bottom plate下托板(底板) ribbon punch压筋冲子stripping plate内外打(脱料板) reel-stretch punch卷圆压平冲子outer stripper外脱料板guide plate定位板inner stripper内脱料板sliding block滑块lower stripper下脱料板sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块冲压名称reel stretch卷圆压平plain die简易模groove压线pierce die冲孔模blanking下料forming die成型模stamp letter冲字(料号) progressive die连续模shearing剪断gang dies复合模tick-mark nearside正面压印shearing die剪边模tick-mark farside反面压印riveting die铆合模extension dwg展开图pierce冲孔procedure dwg工程图forming成型(抽凸,冲凸)die structure dwg模具结构图draw hole抽孔material材质bending折弯material thickness料片厚度trim切边factor系数emboss凸点upward向上dome凸圆downward向下semi-shearing半剪press specification冲床规格stamp mark冲记号die height range适用模高deburr or coin压毛边die height闭模高度punch riveting冲压铆合burr毛边side stretch侧冲压平gap间隙total wt.总重量weight重量punch wt.上模重量high-speed transmission高速传递heat dissipation热传trim剪外边rack上料pierce剪内边degrease脱脂drag form压锻差rinse水洗pocket for the punch head挂钩槽alkaline etch龄咬slug hole废料孔desmut剥黑膜feature die公母模D.I. rinse纯水次expansion dwg展开图Chromate铬酸处理radius半径Anodize阳性处理shim(wedge)楔子seal封孔torch-flame cut火焰切割revision版次set screw止付螺丝part number/P/N料号form block折刀good products良品stop pin定位销scraped products报放心品round pierce punch=die button圆冲子defective products不良品shape punch=die insert异形子finished products成品stock locater block定位块disposed products处理品under cut=scrap chopper清角barcode条码active plate活动板flow chart流程表单baffle plate挡块assembly组装cover plate盖板stamping冲压male die公模molding成型female die母模spare parts=buffer备品groove punch压线冲子coordinate座标air-cushion eject-rod气垫顶杆dismantle the die折模spring-box eject-plate弹簧箱顶板auxiliary fuction辅助功能bushing block衬套poly-line多义线insert 入块heater band 加热片club car高尔夫球车thermocouple热电偶capability能力sand blasting喷沙parameter参数grit 砂砾factor系数derusting machine除锈机phosphate皮膜化成degate打浇口viscosity涂料粘度dryer烘干机alkalidipping脱脂induction感应main manifold主集流脉induction light感应光bezel斜视规response=reaction=interaction感应blanking穿落模ram连杆dejecting顶固模edge finder巡边器demagnetization去磁;消磁concave凸figure file, chart file图档convex凹cutting die, blanking die冲裁模short射料不足progressive die, follow (-on)dienick缺口连续模speck瑕??compound die复合模shine亮班punched hole冲孔splay 银纹panel board镶块gas mark焦痕to cutedges=side cut=side scrap切边delamination起鳞to bending折弯cold slug冷块to pull, to stretch拉伸blush 导色Line streching, line pulling线拉伸gouge沟槽;凿槽engraving, to engrave刻印satin texture段面咬花upsiding down edges翻边witness line证示线to stake铆合patent专利designing, to design设计grit沙砾design modification设计变化granule=peuet=grain细粒die block模块grit maker抽粒机folded block折弯块cushion缓冲sliding block滑块magnalium镁铝合金location pin定位销magnesium镁金lifting pin顶料销metal plate钣金die plate, front board模板lathe车padding block垫块mill锉stepping bar垫条plane刨upper die base上模座grind磨lower die base下模座drill钻upper supporting blank上承板boring镗upper padding plate blank上垫板blinster气泡spare dies模具备品fillet镶;嵌边spring 弹簧through-hole form通孔形式bolt螺栓voller pin formality滚针形式punch冲头cam driver铡楔insert入块(嵌入件)shank摸柄deburring punch压毛边冲子crank shaft曲柄轴groove punch压线冲子augular offset角度偏差stamped punch字模冲子velocity速度round punch圆冲子production tempo生产进度现状special shape punch异形冲子torque扭矩bending block折刀spline=the multiple keys花键roller滚轴quenching淬火baffle plate挡块tempering回火located block定位块annealing退火supporting block for location 定位支承块carbonization碳化air cushion plate气垫板alloy合金air-cushion eject-rod气垫顶杆tungsten high speed steel钨高速的trimming punch切边冲子moly high speed steel钼高速的stiffening rib punch = stinger 加强筋冲子organic solvent有机溶剂ribbon punch压筋冲子bracket小磁导reel-stretch punch卷圆压平冲子liaison联络单guide plate定位板volatile挥发性sliding block滑块resistance电阻sliding dowel block滑块固定块ion离子active plate活动板titrator滴定仪lower sliding plate下滑块板beacon警示灯upper holder block上压块coolant冷却液upper mid plate上中间板crusher破碎机spring box弹簧箱welding line熔合痕spring-box eject-rod弹簧箱顶杆eject pin顶出针spring-box eject-plate弹簧箱顶板knock pin顶出销bushing bolck衬套return pin回位销反顶针cover plate盖板sleave套筒guide pad导料块stripper plate脱料板塑件&模具相关英文insert core放置入子compre sion molding压缩成型runner stripper plate浇道脱料板flash mold溢流式模具guide pin导销plsitive mold挤压式模具eject rod (bar)（成型机）顶业捧split mold分割式模具subzero深冷处理cavity型控母模three plate三极式模具core模心公模runner system浇道系统taper锥拔stress crack应力电裂leather cloak仿皮革orientation定向shiver饰纹sprue gate射料浇口，直浇口flow mark流痕nozzle射嘴welding mark溶合痕slag well冷料井post screw insert螺纹套筒埋值side gate侧浇口self tapping screw自攻螺丝edge gate侧缘浇口striper plate脱料板tab gate搭接浇口piston活塞film gate薄膜浇口cylinder汽缸套flash gate闸门浇口chip细碎物slit gate缝隙浇口handle mold手持式模具移转成型用模具fan gate扇形浇口encapsulation molding低压封装成型dish gate因盘形浇口well type蓄料井two plate两极式（模具）insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道。
模具专业英语术语
模具种类连续模progressive die机械手transfer die手动机械手hand transfer die 单工程模single die简易模prototype die铸造结构模cast die铆合模riveting die复合模compound die冲孔模pierce die剪边模trimming die下料模blanking die成形模forming die折弯模bending die围边模flange die拉伸模draw die快换模changeable die工序类料带strip工序process冲孔pierce切边notch折弯bend成形form整形restrike打凸米boss/dimple打字印stamp面押coin burr拍平flat料带图strip layout冲导正孔pilot pierce侧冲cam pierce切侧刃notch french墩薄coin侧成形cam form围边flange打凸包emboss打沙拉孔bourglass抽孔extrude hole卷圆curl旋转rotate产品切边线trim line切断cutoff料带带料处carrier tab 压线groove铆接rivet铆螺母stake nut接刀口mismatch毛刺方向burr direction 下料blanking模板类上托板top plate上垫脚upper parallel上模座upper die set上垫板punch backup上夹板punch holder上脱料板stripper冲头punch下托板bottom plate下垫脚lower parallel下模座lower die set下垫板lower backup下夹板die holder下模板die plate凹模die零件类浮块lifter成型公form punch切边冲头trim punch沉头孔counter hole顶针kick off/ejector成型凹模forming die导尺rail导尺板rail plate侧冲组件cam滑块上油槽oil groove 码模槽mounting slot限位柱stop block起吊环eyebolt脱料板拉杆spool浮料板lifter plate压料板pressure pad刀口trim steel冲孔入子button废料切断刀slug breaker整形公restrike punch导尺顶杆lifter bolt镶件/入子insert滑块slide铲机driver储运块storage block起吊孔handing hock靠块heel模座导正块thrust heel耐磨片wear plate压块keeper键槽key slot氮气弹簧nitrogen spring聚氨酯弹簧urethane导套guide bushing插针套pilot bushing传感器pilot bushing螺丝screw垫圈washer压毛边冲头deburring punch压线冲头groove punch字模冲头stamp punch压筋冲头ribbon punch异形冲头special shape punch 切边冲头trimming punch加强筋冲头stiffening rib punch 定位板guide plate压边圈binder垫片shim初始管位first start pin键key螺旋弹簧coil spring导柱guide post插针pilot pin侧刃french销dowel拔牙jackscrew盲销blind dowel挡块stopping plate定位块location block圆冲头round punch气垫板air cushion plate气垫顶杆air-cushion eject-rod 上压块pressure block弹簧箱spring box弹簧箱顶杆spring-box eject-rod 弹簧箱顶板spring-box eject-plate公差类公差tolerance上公差upper tolerance公差+/-0.5 plus minus 0.5平面度flatness倾斜度angularity平行度parallelism直线度straightness垂直度perpendicularity圆度roundness圆柱度cylindricity面轮廓度surface profile位置度true position对称度symmetry全跳动total runout角度值angle degree三次元尺寸报告CMM report对称度symmetry同轴度concentricity圆跳动round runout尺寸dimension尺寸全检报告dimensional layout 公差范围tolerance range下公差lower range形位公差图GD&T冲床相关机械冲床mechanical press油压机hydraulic press行程stroke/travel吨位tonnage冲床上台面ram冲床下台面bolster冲床台面布置图press layout冲床上的快速正QDC冲床气垫air cushion码仔stirrup闭合高度shut heightT 型槽T-slot送料机feeder送料高度feeding height工具卡尺caliper千分尺micrometer直尺ruler高度尺height gage丝攻screw tap起子screwdriver拔牙器jacker扳手wrench风磨机hand grinder油石oil stone加工类开料cutting material钻drill（DR）绞ream铣mill车lathe电脑锣NC mill车lathe线切割wire cutting(W/C)磨grind刨planer电火花EDM镭射laser cutting倒角chamferXX的精加工finish XX真空热处理vacuum heat treatment 镀钛TD coating退磁demagnetization烧焊weld。
模具英语专业术语
模具英语专业术语模具的分类:冲压模(五金模): stamping die分离模: cutting die成形模: forming die塑胶模: plastics mold注射模: injection mold压缩模: compression mold铸塑模: transfer mold吹塑模: blow mold吸塑模: suck mold铸造模: casting die砂型铸造: sand casting压铸模: die casting锻造模: forging die塑胶模具术语一、入水：gate进入位(入水点)：gate location水口形式：gate type大水口(侧浇口): edge gate潜水口: sub-gate薄膜式水口: film gate牛角式潜水口: banana gate扇形水口: fan gate环形水口: ring gate二次水口:细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter直接水口: direct gate二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形(整圆/半圆)流道：round(full/half) runner矩形流道: rectangle runner梯形流道: trapezoid runnerU形流道: U shape runner流道电脑分析(模流分析)：mold flow analysis流道平衡: runner balance热嘴：hot sprue/tip热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socket 四、模具零件：mold components 三板模(细水口模)：3-plate mold二板模(大水口模)：2-plate mold热流道模具: hot-runner/manifold mold叠层模: stacked mold边钉/导边：leader pin/guide pin边司/导套：guide pin/guide bushing直导套：shoulder guide bushing有托导套：straight guide bushing中托司：ejector guide bush中托边：ejector guide pin回针: return pin面板: top clamp plateA板: A plate推板：stripper plateB板: B plate托板：support plate方铁: spacer block加高方铁: higher spacer block顶针固定板：ejector retainner plate顶针板：ejector plate底板: bottom clamp plate螺丝：screw杯头螺丝: socket cup head screw平头螺丝: socket flat head screw机米螺丝:外六角头螺丝: bolt栓打螺丝(等高螺丝)：S.H.S.B管钉：dowel pin开模槽：ply bar socket内模管位(模仁互锁)：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：sleeve ejector pin缩呵：movable core,return core, core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide行位扣:镶件：insert压座/斜鸡：wedge耐磨板/油板：wear plate压条：gib撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈(法兰)：locating ring锁扣(模锁)：latch扣鸡：parting lock set推杆：push bar顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring型腔(前模仁): cavity型芯(后模仁): core镶针：insert pin销子(销钉)：dowel pin波子弹弓：ball catch喉塞(堵头): pipe plug锁模块：lock plate斜顶杆：angle ejector rod斜顶针：angle from pin尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边(斜导柱)：angle pin油缸: hydraulic cylinder液压马达: hydraulic motor齿轮: gear轴承: bear术语：terms承压平面平衡：parting surface support balance分模面排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes with ejector pin料位出上/下模：part from cavity (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步模图设计：preliminary mold design正式模图设计：final mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模(粘模)：sticking顶白: stress mark热膨胀：thero expansion缩水: shrinkage物料表: BOM原料: raw materials物料: materials工程试模材料: material for engineering mold testing成品: finished product半成品: semi-finished product公差：tolorance铜公(电极)：copper electrode射料不足: short shot缺口: nick瑕疪(斑点): speck亮斑: shine银纹: splay焦痕: gas mark起鳞: delamination冷块: cold slug导色: blush沟槽;凿槽: gouge段面咬花: satin texture证示线: witness line专利: patent沙砾: grit细粒: granule=peuet=grain抽粒机: grit maker缓冲: cushion不锈钢: stainless steel镁铝合金: magnalium镁金属: magnesium钣金: metal plate车/车床: lathe铣床/铣床: mill刨/刨床: plane磨/磨床: grind钻/钻床: drill镗: boring气泡: blinster版次: revision备注: remark生产确认: production control confirmation 初审: checked by核准: approved by部门: department电镀: plate成型: molding样品: sample雕刻: engrave蚀纹: texture加硬: harden热处理: heat treatment淬火: quenching回火: tempering退火: annealing碳化: carbonization铬酸处理: chromate阳性处理: anodize氮化: nitrifying。
模具专业英语词汇
Injection Mold Technical Terms（一）模具专业基本用词Professional Terms塑料—plastic, resin样件—sample钢料—steel注塑机—injection machine, press产品—part, product, moulding模具—mold, mould, toolA 简易模（样板模）—prototype moldB 量产用模具—production mold 三维造型（数模）—3D model, 3D data二维产品图—2D part drawing设计—design制造—manufacture, build up, construction检验—check, inspection测量—measure, inspection修改—change, modify, correction工程更改—engineer change质量—quality数量—quantity基准—datum, reference牛角入水-rads gate（二）如何解析2D 产品图How to read 2D part drawing产品几何Geometry1．点—point2．线（边）—line, edge3．面faceA 侧面—sideB 表面—surfaceC 外观面—appearance surface 4．壁厚—wall thickness, stock thickness5．加强筋（骨位）—rib6．孔—hole7．细长的槽—slot8．柱位—boss9．角—cornerA 圆角—filletB 倒角—chamferC 尖角—sharp corner 10．斜度—angle, taper11. 凹槽—recess , groove分模信息Splitting分型线—parting line (P/L), splitting line主分模方向—main direction, line of draw浇口设定—gating产品标识Part Identification产品名称—part name (P/N)产品编号+版本号—part number + revision (Rev.)型腔号—cavity number材料标记—material symbol模具编号—mold number (no.)日期印—dating insert, date code循环印—cycling code公司标志—company logo技术要求Specification (Special Requirement)项目启动表Kick-off sheet项目名称—program name, project name产品名称—part name, product name, part description产品编号—part number (P/N)客户模号—customer mold no.项目启动日期—kick off date, start date项目完成日期—due date, lead time内模件用钢—tool steel型腔数量—number of cavities数据文件编号—data file no.注塑材料—resin, plastic, raw material收缩率—shrink, shrinkage, shrink factor注塑机吨位—molding machine size, injection machine size 成型周期—cycle time型腔光洁度—cavity polish型芯光洁度—core polish皮纹（晒纹）—texture, grain拔模斜度—draft angle, removal taper注塑件颜色及光泽—molded color & gloss模具加工地—manufacturing facility热流道供应商—manifold manufacturer, manifold supplier 浇口位置—gate location / position浇口类型—gate type产品标识—stamp information, part identification特殊要求—special instructions安全模数—safe steel产品质量及外观要求Part Quality & Appearance Requirement 尺寸及公差Dimension & Tolerance重要尺寸—critical dimension, important dim., key dim.理论尺寸—nominal dimension实际尺寸—actual dimension公差—tolerance公差带—tolerance range尺寸超差—dimension deviation接受（合格）—accept, OK拒绝（不合格）—reject, refuse, obsolete, NG让步接受—concession, special admit返工—re-work产品缺陷（常见的）Defects (normal)缩水—sink mark, shrinkage飞边，毛边—flash, burr段差—mismatch discrepancy银丝纹，蛇纹—snake marks, streak弯曲，变形—warpage, distortion打不饱（缺料）—short shot熔接线—weld line多胶—unwanted plastic拉伤—damage产品外观Part Appearance产品颜色—part color产品光泽—gloss皮纹粒度—grain常用词汇、词组及短语Normal Word, Short Sentence单边—per side双边—both sides加入，添加—add, incorporate去除，取消—remove, cancel满足…的要求，符合，与…要求一致—according to, conform to, satisfy, meet 要求，需要—require, need, demand确认—be approved, agreed by …允许—permit, allow在…范围之内—within不可以，不允许，禁止—free from, prevent, avoid…，除非有另指—… unless otherwise specified…或少于—…or less自动化运作—automatic operation未注尺寸（详细形状）见三维造型Non dimensioned contour (detailed shape) see 3D model.分型线上的飞边（披缝）或段差应小于…Burrs or discrepancy on the P/L shall be … or less.标题栏Title Block产品名称—part name图纸编号+ 版本号（索引号）—drawing no. + level (index)一般公差—general tolerance（三）如何阅读制模标准How to read tooling standard一．模具结构术语Mold Construction TermsA．模架Mold Base模架量化特征Measurement Feature①长X 宽X 高—Length X Width X Height②模具高度尺寸（模厚）—stack height of mould③模具重量—total weight of mould, mould thickness定模底板—front plate, top clamping plate, clamp plate, clamping plate定模板—cavity plate, fixed mould plate, A – plate动模板—core plate, moving mould plate, B – plate浮动板—floating plate支撑板—support plate, backing plate间隔板,方铁—support blocks, rails, risers, spacer block顶杆固定板—retaining plate, ejector retaining plate顶板—ejector plate，bottom clamping plate动模底板—back plate导柱—guide pillar, leader pin, guide pin导套—guide bush, leader pin bush复位杆—return pin, push-back pin弹簧—spring撑头—support pillar顶针板导柱、导套—ejection guide pin / bush垃圾钉—stop pin, stop button模脚—standing-off pillars标牌—plaque scutcheonB．成型零部件moulding components型芯—core insert型腔—cavity insert镶针—core pin镶块—sub-insert, split滑块—slide, sliding split斜顶—lifter, angled-lift splitA 斜顶头—lifter headB 斜顶杆—lifter rod, lifter shaftC 斜顶连接块——lifter couplingD 斜顶导向块——lifter guideE 斜顶导滑块——lifter Gib成型顶杆—moulding face pin, form pinC．浇注系统Feed System1．塑料Plastic主流道—sprue分流道runner①主分流道—main runner ②二级分流道—branch runner 分流道断面形状cross-sectional shape of runner①圆形—full round②半圆形—semicircular③梯形—trapezoidal浇口gate常用浇口形式normal gate type :①边缘浇口（J型浇口）—edge gate, J – gate②侧浇口—side gate③潜伏式浇口—sub-gate, cashew gate, subsurface gate, submarine gate潜顶针—subgate to pin④潜伏式二次浇口(隧道式浇口) —tunnel gate onto feeder post⑤点浇口—pin gate⑥直接浇口(主流道型浇口) —sprue gate, direct gate⑦护耳式浇口—tab gate模腔—impression冷料井—cold slug well热流道—hot runner2．模具零件mold components定位圈—locating ring, location ring, register ring浇口套—sprue bush挡圈—stop ring浇口镶块—gate insert热流道板—manifold热嘴—hot dropD．分型面及其锁紧、排气Parting Surface, inter-locking & venting分型线—parting line ( P/L )镶拼线—bodyline, joint line平/ 不平的分型面—flat / non – flat parting surface封胶面—shut off surfaces, seal-off surfaces擦穿位—shut off碰穿位—kiss-off管位—parting line lock分型面的释放(避空) —relief of parting surface分型面的平衡—balancing of parting surface锁紧角度—locking angle锁紧力—clamping force锁模块—safety strap精定位—Interlock, die lock困气—air trap排气槽—vent, vent slot撬模坑--- pry slot计数器--- shot counter/ cycle counterE．滑块机构Slide驱动Actuation①斜导柱—angle pin, horn pin, cam pin②弹簧—spring③油缸—hydraulic cylinder制动Detention①滑块固定器—slide retainer②弹簧制动器—spring-loaded detention (plunger)③挡钉、挡板—stop pin, stop plate, slide stop导轨—gib, guide strip,center guide锁紧块（楔紧块）—heel block, locking heel, wedge block, chase block,slide driver 耐磨片—wear plate, wear strip压板—retainer,gib螺钉—screw定位销—dowel pin行位扣—slide lock / slide retainerflat ejector pin 扁顶针F．斜顶机构Lifter斜顶头—lifter head斜顶杆—lifter rod, lifter shaft斜顶固定块—lifter rod retainer斜顶导向块—lifter guide开口销—split pin固定板（压板）—retainer plate耐磨片—wear plate铜导套—bronze bushing导套固定板—bushing retainer衬套—spacer导轨—L – gib导轨---T-Gib滑动块—slide连接块—U-CouplingG．顶出系统Ejection System基本词汇Basic Word顶出行程—ejection stroke模具开档—daylight粘模—stick on产品脱模—part is push off from, clear part of mould, separation of part 顶板机构Ejector plate assembly顶板—ejector plate顶板固定板—retaining plate推板—stripper plate推板导柱—ejector guide pin推板导套—ejector guide bush撑头—support pillar限位块—stop block,stroke block复位机构Return System复位杆（回程杆）—return pin, push – back pin垃圾钉—stop pin, stop button压簧—compressed spring碟簧— a stack of “Belleville” washers早复位机构—early return system强制复位机构—positive return system顶出方法Ejection Techniques顶杆顶出—pin ejection顶管顶出—sleeve ejection顶块顶出—bar ejection扁顶顶出—blade ejection顶板顶出—stripper ejection油缸顶出—hydraulic ejection气顶—air ejection阀门顶出—valve ejection顶出元件Ejection Elements拉料杆—sprue puller, sucker pin顶杆—ejector pin阶梯式顶杆—stepped ejector pin顶管—ejection sleeve, sleeve扁顶—ejector blade, slabbed off ejector pin顶块—stripper bar顶环—stripper ring推板—stripper plate加速顶—accelerated ejection直顶----straight lifter/EJECTOR BAR顶出辅助机构Supplementary operating system弹簧柱塞器—spring – loaded plunger弹珠定位器—ball catch system插销式锁扣—Latch – lock尼龙拉杆装置—friction puller device电器元件Electric Components压力传感器—pressure transducer限位开关—limit switchF．冷却系统Cooling System基本词汇Basic Word温差—temperature variation水孔（水道）—waterlines, water-ways, flow-way, channel水路—cooling circuit水路示意图—water schematic, schematic circuit冷却液—coolant, coolant fluid内连接—interconnect外连接—external connection出口、入口—outlet、inlet漏水—water leakage水路分布Circuits阶梯式水路—stepped system分隔板水路—baffled hole system斜孔式水路—angled hole system水路元件Components闷头（螺塞、止水栓）—（threadless）brass pressure plug : female plug & male 隔水片—baffle密封圈—O – ring快插水路接头—quick disconnect fitting, quick connection adaptor弯头—elbow偶合器（连接器、接头）—adaptor (including a plug & a socket)橡皮管—rubber hose分水板,集水块—water manifoldG．螺纹、螺纹孔& 螺钉Thread, thread hole & screw螺纹—thread管螺纹—pipe thread螺纹孔—screw hole, tapped hole起吊孔—handling hole, jack screw hole, eye bolt hole螺钉—screw内六角螺钉—socket headed cap screw （）沉头螺钉—flat headed cap screw （）螺栓—bolt螺母—nut锁紧螺母—locknut螺纹标准Thread Standard①公制标准—Metric②英制标准—Imperial③英制管螺纹标准—British Standard Pipe thread （BSP）④美制管螺纹标准—NPT⑤美制粗螺纹标准—United Coarse thread （UNC）⑥美制细螺纹标准—United Fine thread （UNF）H．润滑Lubrication润滑槽—grease groove加油管—grease line油杯—lubrication fitting测量仪器Measuring Instruments游标卡尺—vernier caliper千分尺—micrometer高度规—height gauge刻度规—dial gauge三坐标测量仪（三次元）—Coordinate Measure Machine（CMM）塞规—pin gauge圆角量规—radii gauge轮廓投影机—profile projectorJ．注塑机参数Injection Machine Parameter注塑机规格参数Injection Machine Specification①锁紧类型clamp typea．油缸—hydraulic b．肘杆式—toggle②垂直注塑机导柱间距—tie bar vertical clearance③水平注塑机导柱间距—tie bar horizontal clearance④台板尺寸—platen dim.⑤最小/ 最大模厚—mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档—open daylight Min. / Max.⑦锁紧行程—clamp stroke⑧锁紧力—clamping force⑨顶出行程—ejector stroke⑩顶出力—ejector force试模工艺参数Moulding Process Parameter, machine setting①时间Timer（TM）, sec注塑（充填）时间—filling time, injection time冷却时间—cooling time补缩时间—packing time保压时间—holding time成型周期—cycle time②速率、速度Velocity, %、speed, in/sec注塑（充填）速度—injection speed保压速率—hold pressure velocity螺杆转速—screw rotation speed③压力Pressure（Prs.）, psi注塑压力—injection pressure保压压力—hold pressure回压（背压）—back pressure④温度Temperature（Temp.）, °F注塑机喷嘴温度—nozzle temp.料筒前段、中段、后段温度—barrel front、middle、rear temp.模温—mould temp.料温—purged resin melt temp.空射料温—air shot melt temp.。
[整理]模具英语专业术语
![[整理]模具英语专业术语](https://img.taocdn.com/s3/m/f66e4f1e773231126edb6f1aff00bed5b9f373e7.png)
模具（MOULD/MOLD，TOOL）：CAVITY：前模CORE：后模（定模）DIMENSION：寸法GATE：浇口/水口/入水口PIN GATE：点水口/点浇入水SIDE GATE：边水口/侧浇入水/大水口APPERANCE SURFACE：体裁面WARPAGE DIRECTION：变形方向DRAFT ANGEL：脱模斜度PARTING LINE/P。
L：分模线EJECT PIN/E。
P：注塑顶针BLAST/TEXTURE：喷啥，蚀纹MIRROR FINISH：镜面（抛光）处理POLISH：抛光EMD：放电加工WELD：熔接加工（烧焊）LATHE：车床MILLING CUTTER：铣刀MILLING MACHINE：铣床WIRE CUT：线切割CNC：主加工中心POWER DRILL：电钻DRILLING：钻孔FRITING：烧结ANNEALING：淬火注塑术语（INJECTION）SCREW：螺杆WELD LINE：熔接线SINK MARK：缩水DRAG MARK：脱花BURR：批锋FLOW MARK：流纹SHADOW MARK/GLOSS DIFFERENCE：光影SHORT：缺胶INJECTION CYCLE：成型周期注塑英语型厚大小Thick size锁模结构（机绞/直压）Mode locking structure(machine twists/straight pressure)最大开模距离The biggest die sinking is away from动模板最大模具重量Moves the template maximum mold weight哥林柱间距Elder brother forest column spacing顶出形式（电动五点，油压五点，油压十三点）Goes against the form (electrically operated five spots, flowing tubing head pressure five spots, flowing tubing head pressure 13 spots)顶出长度Goes against the length顶棍孔直径Goes against the stick hole diameter顶棍孔中心矩Goes against the stick hole central moment螺杆材质（合金）Screw rod material quality (alloy)螺杆转速Screw rod rotational speed最大射出体积Projects the volume most greatly最大射出量Projects the quantity most greatly射出率Ejection rate每10mm射出量（理论）Each 10mm projects the quantity (theory)射咀直径Shoots ju the diameter射咀R值Shoots ju the R value射咀空径Shoots ju the spatial diameter定位环直径Locating ring diameter溶胶能力Sol ability驱动方式（全自动/全液压）Drive type (completely automatic/entire hydraulic pressure)电压Voltage电热功率Electric heating power电机功率Electrical machinery power作动油量Does moves the oil mass机械尺寸Mechanical size机械重量Mechanical weight最高溶胶温度Highest sol temperature是否带中子Whether to bring the neutron是否带吹气Whether to have the air flus开模行程，open ould stroke定产，order production定产效率，efficiency of order prod uction注胶切换点，glue-injection switching point保压压力1，protective pressure倒索，inverse sling模保护，mould protection关模低压，close mould low pressure炮筒温度，gun barrel temperature回料量，returning amount注射压力，injecting pressure色母配比，raw color ratio mixing配套摸具，matched mold顶针次数，thimble times立式注胶机vertical injector工艺卡，WSP(work specification procedure)工作指导work instr uction注塑机部分英语钣金machine cover / upper cover/ side cover锁模部分clamping unit射胶部分injection unit机架machine frame / base电气系统electric system液压系统hydraulic system机械系统mechanical system机门safety door / fixed door / movable door锁模部分clamping unit电脑控制器computer controller机械安全锁mechanical safety interlock射胶部分injection unit液压系统hydraulic system电箱electrical cabinet / cable机架分体线stand split line机架螺丝孔foundation bolt hole机架machine base / supporting frame理论注射容积theoretical shot volume实际注射量shot weight螺杆直径screw diameter注射压力injection pressure注射速度injection speed注射速率injection rate螺杆长径比screw L/D ratio螺杆行程screw stroke螺杆转速screw speed熔胶能力plasticizing capacity锁模力clamping force开模/锁模行程mold clamping / opening stroke模板尺寸platen size拉杆间距distance between tie bars / rods模板最大距离max. daylight容模量mold thickness (min. & max.)顶出行程hydraulic ejection stroke顶出力hydraulic ejection force顶针数nos. of ejector pin液压系统压力hydraulic system pressure油泵马达pump motor电热量heating capacity温度控制区数nos. of temp control zones射嘴接触力nozzle contact forceInjection 注射Mould closing 关模Cooling time冷却时间Holding time 保压时间Injection start delay 注射延迟Injection alarm time注射报警时间Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Hydraulic pressure in holding锁模力Filling stage pressure limit充模压力Injection speed注射速度Plasticizing delay预塑延时1st suck-back speed储料一速度1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould close force关模压力Mould closing safety time .. 时间Mould closing pressure .. 压力1st closing safety stage pressure 合模一段压力1st mould closing speed ...成型速度1st stage mould closing safety position.....位置High pressure start position高压锁模位置注塑专业英语Surface Appearance外观Glossiness/gloss finish光洁度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹Flow mark流纹Weld line溶结纹Brittle/brittleness脆Bubbles/trapped gas气泡Void孔Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃V-2Poor dispersion分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous粒子不密/蜜蜂窝Low impact/tensile etc物理性能低High flow/filler content etc流动性/填充…过高Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles玻纤结团Product was rejected due to 产品不能接受因为…High moisture level高水分Warpage/warped翘曲Shrinkage/shrink收缩Sink marks缩影Short shot/short molding打不满Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边Discoloration变色Off color颜色差异Flow rate流动率Viscous粘High flow高流动Low flow低流动Sticky粘Mold release脱模Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in extra …添加多一点…Reduced … content减少…含量Dropped/reduced … by x％减少…含量…％Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption预计年/月用量--- 详细信息1. 注射模具名称注射模：Injection mould热塑性塑料注射模：Injection mould for thermoplasctics 热固性塑料注射模：Injection mould for thermosets无流道模：Runerless mould热流道模：Hot runner mould绝热流道模：Insulated温流道模：Warm runner mould2. 浇注，排溢，分型浇注系统：Feed system主流道：Sprue分流道：Runner浇口：Gate直接浇口：Direct gate ;Sprue gate环行浇口：Ring gate盘型浇口：Disk gate ;Diaphragm轮辐浇口：Spoke gate :Spider gate点浇口：Pin-point gate侧浇口：Edge gate潜伏浇口：Submarine gate护耳浇口：Tab gate扇型浇口：Fan gate 牛角浇口：Horn gate冷料穴：Cold-slug well浇口套：Sprue bush ;Sprue bushing浇口镶块：Gating insret分流锥：Sprader流道板：Runner plate热流道板：Manifold block;Hot-runner manifold温流道板：Warm runner plate二级喷嘴：Secondary nozzle鱼雷形组合体：Torpedo;T orpedo body assembly管式加热器：Cartridge heater热管：Heat pipe阀式浇口：Valve gate加热腔：Loading chamber柱塞：Force plunger;Pot plungr溢料槽：Flash grorve ;Spew grovve排气槽：Vent分型面：Parting line水平分型面：Horizontal parting half垂直分型面：Vertical parting half3. 成型零件定模：Stationary mould:Fixed half动模；Movable mould ;Moving half上模:Upper mould;Upper half下模：Lower mould :Lower half型腔：Cavity凹模：Impression;Cavity plate镶件：Mould insert活动镶件：Movable insert;Lose detail拼块：Splits凹模拼块：Cavity splits型芯拼块：Core splits型芯：Core侧型芯：Side core:slide core螺纹型芯：Thread plug;Threaded core螺纹型环：Thread ring;Threaded cavity凸模：Punch;Force嵌件：Insert for mould4. 支持与固定零件定模座板：Fixed clamp plate:Top clamping plate;Top plate动模座板：Moving clamp plate :Bottom clamping plate; Bottm plate 上模座板：Upper clamping plate下模座板：Lower clamping plate凹模固定板：Cavity-retaier plate型芯固定板：Core-retaier plate凸模固定板：Punch-retaier pilte模套：Chase ;Bolster;Frame;支撑板：Backing plate垫块：Spacer parallel支架：Ejector housing支撑柱：Support pillar模板：Mould plate5. 抽芯零件斜销：Angle pin; Finger cam滑块：Slide;Cam slide侧型芯滑块：Slide core-slide滑块导板：Slide guide strip锲紧块：Heel block;Wedge block;Locking heel斜槽导板：Finger guide plate弯销：Dog-leg cam斜滑块：Angled-lift splits6. 导向零件导柱：Guide pillar;Guide pin;Leader pin带头导柱：Guide pillar ;Straight leader pin带肩导柱：Guide pillar Shouldered;Shoulder leader pin推板导柱：Ejector guide pillar;Ejeector guide pin导套：Guide bush ;Guide bushing直导套：Guide bush ;Straight ;Straight bushing带头导套：Guide bush ;Shoulder bushing推板导套：Ejector guide bush;Ejector bushing7. 定位和限位零件定位圈：Locating ring锥形定位圈：Mould bases locating elements复位杆：Ejector plate return pin;Push-back pin限位钉：Stop pin;Stop button限位块：Stop block ;Stop pad定距拉杆：Length bolt;Puller bolt定距拉板：Puller plate;Limit plate8. 推出零件推杆：Ejector pin圆柱头推杆：Ejector pin with cytindrical head带肩推杆:Shouldered ejector pin扁推杆:Flar ejector pin推管：Ejector sleeve推块：Ejector pad推件板：Stripper plate推件环：Stripper ring;Stripper dlisk推杆固定板：Ejector retainer plate推板：Ejector plate;Ejection plate连接推杆：Ejector tie rod 拉料杆：Sprue puller钩形垃料杆：Sprue puller ;Z-shaped球头垃料杆：Sprue puller;Ball headed圆锥头垃料杆：Sprue puller;Conical headed分流道垃料杆：Runner puller;Runner lock pin推流道板：Runner stripper plate9. 冷却和加热零件冷却通道：Cooling channel;Cooling line隔板：Baffle加热板：Heating plate隔热板：Thermal insulation board10. 模架模架：Mould base标准模架：Standard mould base11. 塑料成型模具的主要设计要素注射能力：Shot capacity收缩率：Shrinkage注射压力：Injection pressure锁模力：Clamping force ;Locking force成型压力：Moulding pressure模内压力：Internal mould pressure;Cavity pressure 开模力：Mould opening force脱模力：Ejection force抽芯力：Core-pulling force抽芯距：Core-pulling distance闭合高度：Mould shut height最大开距：Maximum daylight;Open daylight投影面积：Projected area脱模斜度：Draft脱模距：Stripper distance。
模具专业的英语词汇大全
模具专业的英语词汇大全一、模具基础词汇1. Mold 模具2. Die 冲模3. Core 核心模4. Cavity 型腔5. Mold Base 模架6. Mold Steel 模具钢7. Runner 流道8. Gate 进浇口9. Ejector Pin 顶针10. Ejector Plate 顶板二、模具设计相关词汇1. Draft Angle 脱模斜度2. Parting Line 分模线3. Radius 圆角4. Undercut 难以脱模的凹槽5. Slide 滑块6. Lifters 顶杆7. Cooling Channel 冷却水道8. Injection Point 注射点9. Shrinkage 收缩率10. Molding Cycle 成型周期三、模具加工与维护词汇1. Machining 加工2. Milling 铣削3. Grinding 磨削4. EDM (Electrical Discharge Machining) 电火花加工5. Wire Cutting 线切割6. Polishing 抛光7. Assembly 装配8. Maintenance 维护9. Repair 修理10. Replacement 更换四、模具材料与热处理词汇1. Tool Steel 工具钢2. Stainless Steel 不锈钢3. Aluminum 铝4. Plastic 塑料5. Rubber 橡胶6. Heat Treatment 热处理7. Hardness 硬度8. Tempering 回火9. Quenching 淬火10. Annealing 退火五、模具行业相关词汇1. Mold Maker 模具师傅2. Mold Designer 模具设计师3. Mold Manufacturer 模具制造商4. Injection Molding 注塑成型5. Blow Molding 吹塑成型6. Compression Molding 压缩成型7. Transfer Molding 传递成型8. Prototype Model 原型模具9. Mass Production 批量生产10. Quality Inspection 质量检验六、模具测试与质量控制词汇1. First Article Inspection 首件检查2. Sample 样品3. Defect 缺陷4. Dimensional Accuracy 尺寸精度5. Tolerance 公差6. Surface Finish 表面光洁度7. Stress Analysis 应力分析8. Flow Analysis 流动分析9. Mold Flow Simulation 模具流动模拟10. Quality Control 质量控制七、模具行业常用设备词汇1. Injection Molding Machine 注塑机2. Extruder 挤出机3. Blow Molding Machine 吹塑机4. CNC Machine 数控机床5. Lathe 车床6. Milling Machine 铣床7. Grinder 磨床8. EDM Machine 电火花机床9. Laser Cutter 激光切割机10. Robot 自动化八、模具生产流程词汇1. Design Drawing 设计图纸2. Mold Construction 模具构建3. Machining Process 加工工艺4. Tooling Setup 模具安装5. Trial Run 试模6. Adjustment 调整7. Production Run 生产运行8. Mold Maintenance 模具保养9. Mold Modification 模具修改10. Mold Recycling 模具回收九、模具行业认证与标准词汇1. ISO Certification ISO认证2. Quality Management System 质量管理体系3. Standard 标准化4. DIN 德国工业标准5. ASTM 美国材料与试验协会6. JIS 日本工业标准7. Certification Body 认证机构8. Audit 审核检查9. Compliance 符合性10. Continuous Improvement 持续改进十、模具行业发展趋势词汇1. Automation 自动化2. Intelligent Manufacturing 智能制造3. 3D Printing 三维打印4. Rapid Prototyping 快速原型5. Industry 4.0 工业4.06. Internet of Things (IoT) 物联网7. Big Data 大数据8. Cloud Computing 云计算9. Sustainable Development 可持续发展10. CrossIndustry Integration 跨行业整合通过这些词汇，我们可以看到模具行业不仅涉及具体的技术和操作，还包括了管理、质量控制、认证以及未来的发展趋势。
模具专业英语词汇
Here is a list of mold-related vocabulary in English:1. Mold -模具2. Mold cavity -模腔3. Mold core -模芯4. Mold base -模座5. Injection molding -注塑成型6. Blow molding -吹塑成型7. Compression molding -压缩成型8. Extrusion molding -挤出成型9. Rotational molding -旋转成型10. Thermoforming -热成型11. Mold design -模具设计12. Mold manufacturing -模具制造13. Mold making -模具加工14. Mold material -模具材料15. Mold steel -模具钢16. Mold release agent -脱模剂17. Mold temperature -模具温度18. Mold flow analysis -模流分析19. Mold maintenance -模具维护20. Mold repair -模具修复22. Mold polishing -模具抛光23. Molded part -注塑件24. Molded product -成型产品25. Molded surface -成型表面26. Molded feature -成型特征27. Ejector pins -顶出针28. Runner system -流道系统29. Cooling system -冷却系统30. Venting -通气31. Molded part defects -成型件缺陷32. Molded part warpage -成型件翘曲33. Molded part shrinkage -成型件收缩34. Mold release system -脱模系统35. Mold venting system -通气系统36. Mold temperature controller -模具温度控制器37. Mold gate -模具流道口38. Mold runner -模具流道39. Mold ejector system -模具顶出系统40. Mold clamping force -模具锁模力41. Mold shot size -模具射胶量42. Mold cycle time -模具循环时间44. Mold cooling time -模具冷却时间45. Mold release mechanism -模具脱模机构46. Molded part dimensions -成型件尺寸47. Molded part tolerance -成型件公差48. Molded part surface finish -成型件表面处理49. Molded part strength -成型件强度50. Molded part flexibility -成型件柔韧性51. Molded part accuracy -成型件精度52. Molded part durability -成型件耐久性53. Molded part weight -成型件重量54. Molded part texture -成型件纹理55. Molded part transparency -成型件透明度56. Molded part color -成型件颜色57. Molded part function -成型件功能58. Molded part assembly -成型件装配59. Molded part packaging -成型件包装60. Molded part labeling -成型件标记61. Molded part quality control -成型件质量控制62. Mold material selection -模具材料选择63. Mold design software -模具设计软件64. Mold manufacturing process -模具制造过程65. Mold injection molding machine -模具注塑机66. Mold blow molding machine -模具吹塑机67. Mold compression molding machine -模具压缩成型机68. Mold extrusion molding machine -模具挤出成型机69. Mold rotational molding machine -模具旋转成型机70. Mold thermoforming machine -模具热成型机71. Mold tooling -模具工装72. Molded part inspection -成型件检验73. Molded part packaging -成型件包装74. Molded part labeling -成型件标记75. Molded part storage -成型件存储76. Molded part transportation -成型件运输77. Molded part disposal -成型件处理78. Molded part recycling -成型件回收79. Molded part cost -成型件成本80. Molded part production rate -成型件生产率81. Molded part tooling cost -成型件工装成本82. Molded part tooling lead time -成型件工装交货期83. Molded part tooling lifespan -成型件工装寿命84. Molded part tooling maintenance -成型件工装维护85. Molded part tooling repair -成型件工装修复86. Molded part tooling modification -成型件工装修改87. Molded part tooling replacement -成型件工装更换88. Molded part tooling storage -成型件工装存储89. Molded part tooling transportation -成型件工装运输90. Molded part tooling disposal -成型件工装处理91. Molded part tooling recycling -成型件工装回收92. Molded part tooling cost estimation -成型件工装成本估算93. Molded part tooling design optimization -成型件工装设计优化94. Molded part tooling production planning -成型件工装生产计划95. Molded part tooling quality control -成型件工装质量控制96. Molded part tooling process improvement -成型件工装工艺改进97. Molded part tooling waste reduction -成型件工装废物减少98. Molded part tooling cost reduction -成型件工装成本降低99. Molded part tooling cycle time optimization -成型件工装循环时间优化100. Molded part tooling material selection -成型件工装材料选择101. Molded part tooling design validation -成型件工装设计验证102. Molded part tooling production monitoring -成型件工装生产监控103. Molded part tooling maintenance scheduling -成型件工装维护计划104. Molded part tooling repair process -成型件工装修复流程105. Molded part tooling modification process -成型件工装修改流程106. Molded part tooling replacement process -成型件工装更换流程107. Molded part tooling storage management -成型件工装存储管理108. Molded part tooling transportation logistics -成型件工装运输物流109. Molded part tooling disposal methods -成型件工装处理方法110. Molded part tooling recycling techniques -成型件工装回收技术111. Molded part tooling cost estimation tools -成型件工装成本估算工具112. Molded part tooling design optimization software -成型件工装设计优化软件113. Molded part tooling production planning systems -成型件工装生产计划系统114. Molded part tooling quality control methods -成型件工装质量控制方法115. Molded part tooling process improvement strategies -成型件工装工艺改进策略116. Molded part tooling waste reduction techniques -成型件工装废物减少技术117. Molded part tooling cost analysis -成型件工装成本分析118. Molded part tooling design review -成型件工装设计审查119. Molded part tooling production efficiency -成型件工装生产效率120. Molded part tooling maintenance checklist -成型件工装维护清单121. Molded part tooling repair cost estimation -成型件工装修复成本估算122. Molded part tooling modification cost estimation -成型件工装修改成本估算123. Molded part tooling replacement cost estimation -成型件工装更换成本估算124. Molded part tooling storage system -成型件工装存储系统125. Molded part tooling transportation cost calculation -成型件工装运输成本计算126. Molded part tooling disposal methods evaluation -成型件工装处理方法评估127. Molded part tooling recycling process optimization -成型件工装回收流程优化128. Molded part tooling cost reduction strategies -成型件工装成本降低策略129. Molded part tooling cycle time reduction techniques -成型件工装循环时间减少技术130. Molded part tooling material waste reduction -成型件工装材料废物减少131. Molded part tooling design validation methods -成型件工装设计验证方法132. Molded part tooling production monitoring tools -成型件工装生产监控工具133. Molded part tooling maintenance scheduling software -成型件工装维护计划软件134. Molded part tooling repair process optimization -成型件工装修复流程优化135. Molded part tooling modification process improvement -成型件工装修改流程改进136. Molded part tooling replacement process optimization -成型件工装更换流程优化137. Molded part tooling storage management techniques -成型件工装存储管理技术138. Molded part tooling transportation logistics optimization -成型件工装运输物流优化139. Molded part tooling disposal methods assessment -成型件工装处理方法评估140. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估141. Molded part tooling cost estimation software -成型件工装成本估算软件142. Molded part tooling design optimization tools -成型件工装设计优化工具143. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估144. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估145. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施146. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化147. Molded part tooling cost analysis tools -成型件工装成本分析工具148. Molded part tooling design review software -成型件工装设计审查软件149. Molded part tooling production efficiency evaluation -成型件工装生产效率评估150. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化151. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件152. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件153. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件154. Molded part tooling storage system optimization -成型件工装存储系统优化155. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件156. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具157. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术158. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施159. Molded partooling design validation methods -成型件工装设计验证方法160. Molded part tooling production monitoring tools -成型件工装生产监控工具161. Molded part tooling maintenance scheduling software -成型件工装维护计划软件162. Molded part tooling repair process optimization -成型件工装修复流程优化163. Molded part tooling modification process improvement -成型件工装修改流程改进164. Molded part tooling replacement process optimization -成型件工装更换流程优化165. Molded part tooling storage management techniques -成型件工装存储管理技术166. Molded part tooling transportation logistics optimization -成型件工装运输物流优化167. Molded part tooling disposal methods assessment -成型件工装处理方法评估168. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估169. Molded part tooling cost estimation software -成型件工装成本估算软件170. Molded part tooling design optimization tools -成型件工装设计优化工具171. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估172. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估173. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施174. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化175. Molded part tooling cost analysis tools -成型件工装成本分析工具176. Molded part tooling design review software -成型件工装设计审查软件177. Molded part tooling production efficiency evaluation -成型件工装生产效率评估178. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化179. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件180. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件181. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件182. Molded part tooling storage system optimization -成型件工装存储系统优化183. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件184. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具185. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术186. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施187. Molded part tooling risk assessment methods -成型件工装风险评估方法188. Molded part tooling safety protocols optimization -成型件工装安全协议优化189. Molded part tooling environmental impact assessment -成型件工装环境影响评估190. Molded part tooling sustainability evaluation -成型件工装可持续性评估191. Molded part tooling efficiency improvement strategies implementation -成型件工装效率提升策略实施192. Molded part tooling inventory management techniques -成型件工装库存管理技术193. Molded part tooling repair process optimization -成型件工装修复流程优化194. Molded part tooling modification cost reduction techniques -成型件工装修改成本降低技术195. Molded part tooling replacement cost reduction strategies -成型件工装更换成本降低策略196. Molded part tooling storage space optimization techniques -成型件工装存储空间优化技术197. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略198. Molded part tooling disposal methods optimization -成型件工装处理方法优化199. Molded part tooling recycling process evaluation -成型件工装回收流程评估200. Molded part tooling cost analysis techniques -成型件工装成本分析技术201. Molded part tooling design review process optimization -成型件工装设计审查流程优化202. Molded part tooling production efficiency improvement strategies -成型件工装生产效率提升策略203. Molded part tooling maintenance checklist evaluation -成型件工装维护清单评估204. Molded part tooling repair process efficiency improvement techniques -成型件工装修复流程效率提升技术205. Molded part tooling modification cost reduction strategies -成型件工装修改成本降低策略206. Molded part tooling replacement cost reduction techniques -成型件工装更换成本降低技术207. Molded part tooling storage system evaluation -成型件工装存储系统评估208. Molded part tooling transportation cost analysis techniques -成型件工装运输成本分析技术209. Molded part tooling disposal methods optimization strategies -成型件工装处理方法优化策略210. Molded part tooling recycling process efficiency improvement techniques -成型件工装回收流程效率提升技术211. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施212. Molded part tooling risk assessment techniques -成型件工装风险评估技术213. Molded part tooling safety protocols evaluation -成型件工装安全协议评估214. Molded part tooling environmental impact assessment techniques -成型件工装环境影响评估技术215. Molded part tooling sustainability improvement strategies -成型件工装可持续性改进策略216. Molded part tooling efficiency evaluation techniques -成型件工装效率评估技术217. Molded part tooling inventory management optimization -成型件工装库存管理优化218. Molded part tooling repair process efficiency evaluation -成型件工装修复流程效率评估219. Molded part tooling modification cost reduction strategies implementation -成型件工装修改成本降低策略实施220. Molded part tooling replacement cost reduction techniques implementation -成型件工装更换成本降低技术实施221. Molded part tooling storage space optimization strategies -成型件工装存储空间优化策略222. Molded part tooling transportation cost reduction techniques implementation -成型件工装运输成本降低技术实施223. Molded part tooling disposal methods optimization techniques -成型件工装处理方法优化技术224. Molded part tooling recycling process efficiency evaluation -成型件工装回收流程效率评估225. Molded part tooling cost analysis techniques implementation -成型件工装成本分析技术实施226. Molded part tooling design review process optimization strategies -成型件工装设计审查流程优化策略227. Molded part tooling production efficiency improvement techniques implementation -成型件工装生产效率提升技术实施228229. Molded part tooling quality control measures evaluation -成型件工装质量控制措施评估230. Molded part tooling inspection process optimization strategies -成型件工装检验过程优化策略231. Molded part tooling maintenance schedule development -成型件工装维护计划制定232. Molded part tooling repair cost analysis techniques -成型件工装修复成本分析技术233. Molded part tooling modification process efficiency improvement techniques implementation -成型件工装修改过程效率提升技术实施234. Molded part tooling replacement process cost reduction strategies implementation -成型件工装更换过程成本降低策略实施235. Molded part tooling storage system optimization -成型件工装存储系统优化236. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术实施237. Molded part tooling disposal methods evaluation -成型件工装处理方法评估238. Molded part tooling recycling process efficiency improvement techniques implementation -成型件工装回收流程效率提升技术实施239. Molded part tooling cost reduction strategies evaluation -成型件工装成本降低策略评估240. Molded part tooling risk assessment techniques implementation -成型件工装风险评估技术实施241. Molded part tooling safety protocols optimization strategies -成型件工装安全协议优化策略242. Molded part tooling environmental impact assessment techniques implementation -成型件工装环境影响评估技术实施243. Molded part tooling sustainability improvement strategies evaluation -成型件工装可持续性改进策略评估244. Molded part tooling efficiency evaluation techniques implementation -成型件工装效率评估技术实施245. Molded part tooling inventory management optimization strategies implementation -成型件工装库存管理优化策略实施246. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复流程效率评估技术247. Molded part tooling modification cost reduction strategies evaluation -成型件工装修改成本降低策略评估248. Molded part tooling replacement cost reduction techniques evaluation -成型件工装更换成本降低技术评估249. Molded part tooling storage space optimization strategies implementation -成型件工装存储空间优化策略实施250. Molded part tooling transportation cost reduction techniques evaluation -成型件工装运输成本降低技术评估251. Molded part tooling design optimization techniques implementation -成型件工装设计优化技术实施252. Molded part tooling production capacity evaluation -成型件工装生产能力评估253. Molded part tooling inspection methods improvement strategies -成型件工装检验方法改进策略254. Molded part tooling maintenance cost analysis techniques -成型件工装维护成本分析技术255. Molded part tooling repair process optimization strategies implementation -成型件工装修复过程优化策略实施256. Molded part tooling modification process cost reduction techniques -成型件工装修改过程成本降低技术257. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术258. Molded part tooling storage system efficiency improvement strategies implementation -成型件工装存储系统效率提升策略实施259. Molded part tooling transportation cost reduction strategies evaluation -成型件工装运输成本降低策略评估260. Molded part tooling disposal methods optimization techniques implementation -成型件工装处理方法优化技术实施261. Molded part tooling quality control measures implementation -成型件工装质量控制措施实施262. Molded part tooling material selection criteria evaluation -成型件工装材料选择标准评估263. Molded part tooling cost estimation techniques implementation -成型件工装成本估算技术实施264. Molded part tooling waste reduction strategies evaluation -成型件工装废料减少策略评估265. Molded part tooling energy consumption optimization techniques -成型件工装能源消耗优化技术266. Molded part tooling production cycle time reduction strategies evaluation -成型件工装生产周期缩短策略评估267. Molded part tooling training programs implementation -成型件工装培训计划实施268. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略269. Molded part tooling inspection frequency evaluation techniques -成型件工装检验频率评估技术270. Molded part tooling repair cost reduction strategies implementation -成型件工装修复成本降低策略实施271. Molded part tooling modification process efficiency evaluation techniques -成型件工装修改过程效率评估技术272. Molded part tooling replacement process cost reduction strategies -成型件工装更换过程成本降低策略273. Molded part tooling storage system organization techniques implementation -成型件工装存储系统组织技术实施274. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估275. Molded part tooling disposal methods cost evaluation techniques -成型件工装处理方法成本评估技术276. Molded part tooling quality assurance audits implementation -成型件工装质量保证审计实施277. Molded part tooling material sourcing optimization strategies -成型件工装材料采购优化策略278. Molded part tooling cost control measures implementation -成型件工装成本控制措施实施279. Molded part tooling waste management techniques evaluation -成型件工装废料管理技术评估280. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略281. Molded part tooling production planning optimization techniques implementation -成型件工装生产计划优化技术实施282. Molded part tooling training effectiveness evaluation techniques -成型件工装培训效果评估技术283. Molded part tooling maintenance cost reduction strategies evaluation -成型件工装维护成本降低策略评估284. Molded part tooling inspection methods optimization techniques -成型件工装检验方法优化技术285. Molded part tooling repair process cost reduction strategies implementation -成型件工装修复过程成本降低策略实施286. Molded part tooling modification process efficiency improvement techniques -成型件工装修改过程效率提升技术287. Molded part tooling replacement process safety protocols evaluation -成型件工装更换过程安全协议评估288. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略289. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术290. Molded part tooling disposal methods efficiency evaluation techniques -成型件工装处理方法效率评估技术291. Molded part tooling quality control system implementation -成型件工装质量控制系统实施292. Molded part tooling material selection process optimization strategies -成型件工装材料选择过程优化策略293. Molded part tooling cost estimation accuracy evaluation techniques -成型件工装成本估算准确度评估技术294. Molded part tooling waste reduction techniques implementation -成型件工装废料减少技295. Molded part tooling energy consumption monitoring system implementation -成型件工装能耗监测系统实施296. Molded part tooling production scheduling optimization strategies -成型件工装生产调度优化策略297. Molded part tooling training program development techniques -成型件工装培训计划开发技术298. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略299. Molded part tooling inspection frequency optimization techniques -成型件工装检验频率优化技术300. Molded part tooling repair process efficiency improvement strategies -成型件工装修复过程效率提升策略301. Molded part tooling replacement cost analysis techniques -成型件工装更换成本分析技术302. Molded part tooling storage system organization techniques -成型件工装存储系统组织技术303. Molded part tooling transportation safety protocols implementation -成型件工装运输安全协议实施304. Molded part tooling disposal methods cost analysis techniques -成型件工装处理方法成本分析技术305. Molded part tooling quality control system evaluation techniques -成型件工装质量控制系统评估技术306. Molded part tooling material selection process efficiency evaluation techniques -成型件工装材料选择过程效率评估技术307. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确度提升策略308. Molded part tooling waste management system implementation -成型件工装废料管理系统实施309. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术310. Molded part tooling production scheduling efficiency evaluationtechniques -成型件工装生产调度效率评估技术311. Molded part tooling training program effectiveness evaluation techniques -成型件工装培训计划效果评估技术312. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术313. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略314. Molded part tooling repair process cost analysis techniques -成型件工装修复过程成本分析技术315. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术316. Molded part tooling storage system space utilization techniques -成型件工装存储系统空间利用技术317. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略318. Molded part tooling disposal methods efficiency improvement strategies -成型件工装处理方法效率提升策略319. Molded part tooling quality control system implementation techniques -成型件工装质量控制系统实施技术320. Molded part tooling material selection process optimization techniques -成型件工装材料选择过程优化技术321. Molded part tooling cost estimation accuracy improvementtechniques -成型件工装成本估算准确度提升技术322. Molded part tooling waste reduction strategies implementation -成型件工装废料减少策略实施323. Molded part tooling energy consumption monitoring system optimization techniques -成型件工装能耗监测系统优化技术324. Molded part tooling production scheduling efficiency improvement strategies -成型件工装生产调度效率提升策略325. Molded part tooling training program development techniques -成型件工装培训计划开发技术326. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术327. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略328. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复过程效率评估技术329. Molded part tooling replacement cost analysis methods -成型件工装更换成本分析方法330. Molded part tooling storage system organization strategies -成型件工装存储系统组织策略331. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估332. Molded part tooling disposal methods cost analysis methods -成型件工装处理方法成本分析方法333. Molded part tooling quality control system effectiveness evaluation techniques -成型件工装质量控制系统效果评估技术334. Molded part tooling material selection process efficiency improvement strategies -成型件工装材料选择过程效率提升策335. Molded part tooling cost optimization techniques -成型件工装成本优化技术336. Molded part tooling maintenance record keeping methods -成型件工装维护记录保持方法337. Molded part tooling inspection checklist development techniques -成型件工装检查清单开发技术338. Molded part tooling repair process time reduction strategies -成型件工装修复过程时间减少策略339. Molded part tooling replacement frequency analysis methods -成型件工装更换频率分析方法340. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术341. Molded part tooling transportation route optimization strategies -成型件工装运输路线优化策略342. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术343. Molded part tooling quality control system auditing methods -成型件工装质量控制系统审核方法344. Molded part tooling material selection process cost analysis techniques -成型件工装材料选择过程成本分析技术345. Molded part tooling cost estimation error analysis techniques -成型件工装成本估算误差分析技术346. Molded part tooling waste reduction strategies implementation monitoring techniques -成型件工装废料减少策略实施监测技术347. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术348. Molded part tooling production scheduling optimization techniques -成型件工装生产调度优化技术349. Molded part tooling training program effectiveness evaluation methods -成型件工装培训计划效果评估方法350. Molded part tooling maintenance schedule flexibility strategies -成型件工装维护计划灵活性策略351. Molded part tooling design software proficiency assessment methods -成型件工装设计软件熟练度评估方法352. Molded part tooling cost reduction strategies implementation monitoring techniques -成型件工装成本降低策略实施监测技术353. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略354. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法355. Molded part tooling disposal methods regulatory compliance evaluation techniques -成型件工装处理方法合规性评估技术356. Molded part tooling quality control system training program development techniques -成型件工装质量控制系统培训计划开发技术357. Molded part tooling material selection process sustainability assessment methods -成型件工装材料选择过程可持续性评估方法358. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确性提升策略359. Molded part tooling waste management system implementation techniques -成型件工装废料管理系统实施技术360. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略361. Molded part tooling production scheduling flexibility analysis methods -成型件工装生产调度灵活性分析方法362. Molded part tooling training program effectiveness evaluation criteria -成型件工装培训计划效果评估标准363. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术364. Molded part tooling design optimization methods for reducing defects -成型件工装设计优化方法降低缺陷365. Molded part tooling cost estimation techniques for new product development -成型件工装成本估算技术新产品开发366. Molded part tooling storage system inventory tracking methods -成型件工装存储系统库存跟踪方法367. Molded part tooling transportation risk mitigation strategies -成型件工装运输风险缓解策略368. Molded part tooling disposal methods environmental sustainability evaluation techniques -成型件工装处理方法环境可持续性评估技术369. Molded part tooling quality control system documentation management techniques -成型件工装质量控制系统文件管理技术370. Molded part tooling material selection process sustainability improvement strategies -成型件工装材料选择过程可持续性改善策略371. Molded part tooling cost estimation error reduction techniques -成型件工装成本估算误差减少技术372. Molded part tooling waste reduction strategies effectiveness evaluation methods -成型件工装废料减少策略效果评估方法373. Molded part tooling energy consumption monitoring techniques -成型件工装能耗监测技术374. Molded part tooling production scheduling optimization tools -成型件工装生产调度优化工具375. Molded part tooling training program evaluation methods -成型件工装培训计划评估方法376. Molded part tooling maintenance schedule adjustment techniques -成型件工装维护计划调整技术377. Molded part tooling design software selection criteria -成型件工装设计软件选择标准378. Molded part tooling cost reduction strategies effectiveness evaluation methods -成型件工装成本降低策略效果评估方法379. Molded part tooling storage system organization tools -成型件工装存储系统组织工具380. Molded part tooling transportation risk mitigation measures -成型件工装运输风险缓解措施381. Molded part tooling disposal methods regulatory compliance monitoring techniques -成型件工装处理方法合规性监测技术382. Molded part tooling quality control system training program evaluation methods -成型件工装质量控制系统培训计划评估方法383. Molded part tooling material selection process cost-benefit analysis techniques -成型件工装材料选择过程成本效益分析技术384. Molded part tooling waste management strategies sustainability assessment methods -成型件工装废料管理策略可持续性评估方法385. Molded part tooling energy efficiency improvement measures -成型件工装能效改善措施386. Molded part tooling production scheduling optimization algorithms-成型件工装生产调度优化算法387. Molded part tooling training program effectiveness evaluation tools -成型件工装培训计划效果评估工具388. Molded part tooling maintenance schedule optimization models -成型件工装维护计划优化模型389. Molded part tooling design optimization techniques for improving product performance -成型件工装设计优化技术提高产品性能390. Molded part tooling cost estimation methods for budget planning -成型件工装成本估算方法预算规划391. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术392. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法393. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术394. Molded part tooling quality control system documentation control methods -成型件工装质量控制系统文件控制方法395. Molded part tooling material selection process sustainability evaluation criteria -成型件工装材料选择过程可持续性评估标准396. Molded part tooling cost estimation accuracy improvement techniques -成型件工装成本估算准确性改善技术397. Molded part tooling waste reduction strategies monitoring methods。
模具专业英语
Injection machine 啤机Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程non-return valve 止回阀shear 剪切opening 开模行程Injection pressure 射胶压力back pressure 背压nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要设备Reserve pressure/packing pressure保压mold trial 试模shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度booster time 增压时间Compression ratio 压缩比mold close time 合模时间Resin 胶料Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Booster time 增压时间feed 喂料，填充purge 净化degradation 降解，软化regrind 再粉碎Water absorption 吸水reinforce 增强，加固specific gravity 比重Elongation 延伸率density 密度melting point 熔点Mold materials 模具General purpose steel 多用途钢tool steel 模具钢Free-cutting steel 高速切削钢case hardening steel 表面硬化钢Pre-hardened steel 预硬钢ball and roller bearing steel 滚珠轴承钢Nonferrous steel 非铁合金high speed steel 高速钢cast iron 铸铁Steel specification 钢材规格steel certification 钢材合格证明书Stainless steel 不锈钢nickel 镍chrome 铬aluminum 铝Copper 铜brass 黄铜bronze 青铜titanium 钛Processing 钢材的加工方法nitride 氮化temper 回火anneal 退火abrasive 研磨，磨损的finish 精加工，抛光（polish）Case-hardening 表面硬化milling machine 铣（锣）床Lathe车床drill 钻床wire cut 线割NC(numerical control ) 数控材料EDM (Electrical discharge machine) 电火花加工Cut steel 开料Precision ground 精密研磨heat treatment 热处理tap 丝锥，攻牙Texture 蚀纹weld 焊接forge 锻压deformation 变形Spraying 喷涂die-cast 压铸Properties 性能Resistance 电阻，抵抗能力abrasion / wear磨损erode / corrode 腐蚀Toughness 韧性yield strength 屈服强度tensile strength 拉伸强度Fatigue strength 疲劳强度break 断裂stress 应力hardness 硬度Humidity / moisture 潮湿，湿气roughness 粗糙度parameter 参数Thermal conductivity 导热系数Ductility 延展性grain 晶粒property 性能，财产brittleness 脆性GD&T （Geometric Dimensions and Tolerance ）形位尺寸公差Flexural strength 挠曲强度impact 冲击conductivity 传导性，导电性Optical 光学的transparent 透明的insulation 绝缘Mechanical 机械的processability 可加工性能time yield 蠕变Physical 物理的flow rate 流动速率compressive strength 压缩强度Adhesive 粘附的，胶合durability 耐用性Mold design 模具设计Tooling specification 模具规格mould flow 流动模拟sprue nozzle 唧咀孔Clearance 避空，间隙undercut 倒扣flush 插入，埋入legend 图例Groove 凹槽latch 插销class 类型，种类plan 平面图Orifice 孔，口column 柱位boss 凸台standard 标准，规格Rib 骨位tapered interlock 锥形管位块Bubbler 炮隆Bolt 螺钉，销顶identification mark 铭牌P/L strip 锁模片Overflow well / cold-slug well 冷料井Vent 排气pocket 槽Gate location 入水点full line 实线broken line 虚线Retainer 固定，支撑Lifting hole 吊令孔insulation plate 隔热板cavity number 型腔号Bolster 支撑，垫子vent channel 排气槽leak / filter 渗漏Leak test 试运水stamp / engrave 雕刻，印记（打字唛）Clamp slot 码模槽support button / pin 垃圾钉cut steel 开料Lodge 安装，放置inlay 镶嵌，插入cam / lifter 斜顶Stripper推方lifting bar 吊模方tolerance 公差Counter bore 沉孔slant 倾斜，斜面conical 圆锥的，圆锥形的Bolt 螺栓manifold 热流道板prototype tooling 原型试验Gusset 角撑reverse mold 倒装模constrain / restrict约束，限制Counter lock 反锁thermocouple 热电偶mold maker 模具制造商Asset / property number 资产编号tool product destination 模具生产地点Accelerating ejection 加速顶出hydraulic 液压的pneumatic 气动的Trapezoid 梯形的semi-round 半圆形format 格式baffle 隔水片Electrode 电极，铜公spare part 配件gall 磨伤，插伤Cable 电缆，电线plating / coating （电）镀bonding / joint 接头Wall transition 壁厚过渡Product problem 产品问题Troubleshoot 故障处理reduce(add) plastic 减（加）胶Burr/flash披峰Burn mark 烧焦ejector mark 顶针印，顶白black specs 黑点，黑斑Discoloration 混色，污点gloss 光泽jetting/worming 走水纹Sink mark 缩水void / bubble 气泡，夹气distortion 变形short molding / non-fill缺胶，未走齐Weld line / knit line 夹水线discarded as useless 报废Split line 夹线stick in sprue bushing / cavity / core 粘唧咀/前模/后模Break / crack 顶裂brittleness 脆性，易脆Others 其他Invoice 发票，清单vendor(er) 卖方vendee 买方guideline 方针，指导Intricate 复杂的confidential 机密的，不可外泄的proprietary 私有的Authorize 批准，授权recipient 接收者issue ①发布，提供；②问题Approve 确认，赞成requirement 需要，必需物const 常数，常量Regarding 关于，涉及opposite 相反的，对面的latitude 纬度，纵向的Version 版本definition 注释，解说transversal 横向的，截线Profile 轮廓，剖面eliminate / cancel 取消allow / permit 允许，许可Respective 各自的，分别的individual 单独的Preliminary 初步的approximately 大约，近似estimate / valuate估计，预算Adjust 调整，校准application 应用，申请maintain 维持Accurate / precise 精确的smooth 光滑，顺畅的device 装置，设备Convenient 方便的deadline 截至日期available 有用的，有空的Shift 轮班，换班critical 关键的，临界的exceptional 异常的，优异的Exceed 超过layout 布局，方案loss 损失，消耗install 安装，安置Rotation 旋转item 条款，项目quotation 报价stabilize 稳定Quality 质量quantity 数量couple 连接，接合configuration 构造，外形Illustrate 图解说明simulation 模拟，仿真。
模具英语专业术语
模具英语专业术语如下：1. 模具：Mold，Die2. 模具设计：Mold Design3. 模具制造：Mold Manufacturing4. 模具工程师：Mold Engineer5. 模具材料：Mold Material6. 耐磨材料：wear-resistant material7. 热处理：Heat Treatment8. 水路设计：Water Path Design9. 浇注系统：Injection Sleeve10. 冷却系统：Cooling System11. 顶出系统：Pop-out System12. 复位系统：Reset System13. 导向机构：Guide Device14. 模板：Base Plate15. 顶杆：Pushrod16. 复位杆：Reset Rod17. 斜导柱：Oblique Guide Column18. 导套：Guide Bushing19. 滑块：Slider20. 镶针：Pillow Block21. 弹簧：Spring22. 皮囊弹簧：Kelvin Spring23. 油压缓冲器：Hydraulic Buffer24. 压力表：Pressure Gauge25. 安全阀：Safety Valve26. 水路板：Waterway Plate27. 分流器：Flow Divider28. 水口：Filler Port29. 冷料穴：Cold Molding Chamber30. 模具钢：Mold Steel31. SKH-55、SKH-55M、高速工具钢、HSS等。
32. SKD、SKH-S、SKD61、SKH-9等。
模具钢硬度（Hardness of die steel）：布氏硬度（HB）、洛氏硬度（HRC）、维氏硬度（HV）等。
33. SKD61(级硬SKD61) ，Cr12MoV，A3，A2，SKH-9，718，738，P20等。
塑料模具钢有PXZ、SACD、S136、S718、SS446、3Cr2Mo等。
模具专业英语1
模具专业英语gate：进胶gate location：进胶位gate size：胶口尺寸gate type：胶口形式switching runner/gate：转水口edge gate：大水口（侧进胶）pin-point gate：细水口sprue diameter：直接进胶cashew/banana gate：牛角/香蕉进胶sub/tunnel gate：潜水进胶fan gate：扇形进胶tab gate：搭接/边进胶hot runner system：热流道runner：流道/水口cavity：前模core：后模slide：行位insert：镶件lifter：斜顶buffle：隔水片stop pin：垃圾钉core pin：镶钉location ring：定位圈ejector pin：顶针ejector sleeve：司筒stripper plate：推板（脱料板）leader pin：导柱guide pin：中托边dowel pin：销钉return pin：回针wedge：铲基wear plate：耐磨块stop plate：挡板support pillar：撑头shut-off：枕位switch：转换开关micro-switch：微转换开关inter-lock：互锁lock：边锁interchangeable inserts：互换镶件spring：弹簧clearance：避空steel safety：预留thickness/wall：壁厚（胶位）gloss：光滑gloss shine/shinny：太光no flash：没批风no burr：没批风（用于五金件中）drill through：通孔tap：攻牙thread：攻牙blind：盲孔finish：表面要求polish：抛光texture：晒纹engrave：雕刻laser engrave：激光雕刻flush：面面平齐off-set：偏移flow mark：料花sweat out：冒汗shrinkage：缩水率sink：缩水deformation：变形wrap：反变形water line：运水break edge：去毛边gage：量规resin：胶料steel：钢料add steel：减胶reduce steel：加胶welding：烧焊wire-cut：线切割eye-bolt：吊环Rev.：版本becu：铍铜sharp：利角radius：圆角tolerance：公差hydraulic：油缸clinker：芯seals：油封drawing number：图纸编号part number：产品编号part name：产品名称。
模具专业 英语
机器设备 Machine Equipment飞模机 Die Spotting Press数控加工中心(电脑锣） CNC Machine雕刻机 Engraving machine深孔钻 Gun Drilling Machine火花机 Electrical discharge machining （EDM）线切割 Wire EDM铣床Mill Machine磨床Grinding Machine钻床Drilling Machine车床Lathe Machine抛光机 Lapping Machine测量仪器 Measuring Instruments三次元 Coordinate Measuring Machine （CMM）二次元 2D Measuring Instrument轮廓投影仪Profile Projector高度尺 Highly Ruler卡尺vernier caliper千分尺 Micrometer刻度规 Dial Gauge塞规Pin Gauge圆角量规 Radii Gauge治具Fixture试模设备 Tryout Machine注塑机 Injection Machine氮气机（气辅模）Nitrogen Machine （Gas-assisted mold) 干燥机 Drying Machine模温机 Mold Temperature Controller注塑机参数Injection machine parameter台板尺寸 Platen dim最小/大模厚 Min/Max mold thickness最小/大注塑机行程 Min/Max Open daylight锁紧力 Clamp force顶出行程 Ejector stroke成型条件 Molding Conditions机水（普通水） Normal water temperature热油Hot oil冻水Chill water烘干Drying干燥时间 Drying time料管温度 Barrel Temperature熔化温度 Melt Temperature模具温度 Mold Temperature射出压力 Injection Pressure保压Holding Pressure保压时间 Dwelling time背压Back Pressure射出速度 Injection Speed射出温度 Injection Temperature冷却时间 Cooling time成型时间 Cycle tIme成型缺陷 Injection Defects产品外观 Part appearance产品颜色 Part color产品光泽 Gloss缩水印 Sink Mark/Shrinkage结合线 Welding Line变形Warpage/Shape Distortion缺胶（打不满） Short Shot烧焦Bun气纹Gas mark段差Mismatch/Step披风Burr/Flash顶白Ejector Mark污点Dark Spot黑点Black Spot困气Air Trapping拉伤Drag Marks粘前/后模/行位/水口Sticking Cavity/Core/slide/Sprue 流道粘前模Runner stuck to cavity side流纹Streak表面不光 Poor surface模具问题 mould problems顶出行程不够 E.P.distance too short断顶针 Ejector pin broken卡滑块 Slider jam进胶不平衡Filling uneven浇口/流道太大/小Gate/Runner to blg/small挂成品 Part hanging产品断裂 Part broken产品脱落不平衡 Unbalance part release顶针弯 Ejector pin bend顶针不完全复位 Ej P not return fully弹簧失效 Spring fail镶件损坏 Insert dented倒扣Undercut进胶系统 Injection System主流道 Sprue分流道 Runner主分流道 Main runner次级分流道Branch runner圆形Full round半圆形 Semicircular梯形Trapezoidal进胶口 Gate浇口位置 Gate location浇口类型 Gate type边缘浇口 Edge gate侧浇口 Side gate潜浇口 Sub/cashew/subsurface/submarine/tunnel gate 点浇口 Pin gate牛角浇口 banana gate搭接浇口 Tab gate潜顶针 Sub gate onto pin扇形浇口 Fan gate冷料井 Cold slug well热流道 Hot Runner热嘴Hot Bush/Tip/Nozzle分流板 Hot manifold接线盒 Connecting box热电偶 Thermocouple冷却系统 Cooling System铜塞Brass pressure plug隔水片 Baffle密封圈 O ring水嘴Cooling fitting温差Temperature variation水路Waterlines水路示意图Water schematic进/出水In/Out漏水Water Leakage积水块 Water manifold阶梯式水路Steeped system喷淋式水路Baffled hole system斜水路 Angled hole system顶出方式 Ejection Techniques顶针顶出 Pin Ejection司筒顶出 Sleeve Ejection顶块顶出 Bar Ejection扁顶顶出 Blade Ejection推板顶出 Stripper Ejection油缸顶出 Hydraulic Ejection气顶Air Ejection水口钩针 Sprue Puller顶针Ejector pin带托顶针 Stepped ejector pin司筒Ejector Sleeve扁顶Ejector blade顶块Stripper Bar推环Stripper ring推板Stripper plate加速顶 Accelerated ejection二次顶 Two Stage ejector早回机构 Early ejector return螺纹标准 Thread Standard公制标准 Metric英制标准 Imperial英制管螺纹British standard Pipe thread (BSP) 美制管螺纹NPT美制粗螺纹United coarse thread (UNC)美制细螺纹United Fine thread (UNF)管螺纹 Pipe thread螺纹孔 Screw hole起吊孔 Handling hole螺钉Screw螺栓Bolt螺母Nut模具结构 Mold Structure模胚Mold base面板Top Clamp Plate水口板（3板模） Runner Stripper Plate （3 plate mold) 热流道板 Hot Runner-plateA板 A plateB板 B Plate推板Stripper Plate支撑板 Support Plate方铁Spacer Block顶针板 Ejector Retainer Plate顶针底板 Ejector Plate底板Bottom Clamp Plate锁模块 Lock Block模脚Support leg铭牌Nameplate吊环Safety Hoist Ring导柱Guide Pin导套Guide Bush铜导套 Bronze bushing石墨导套 Graphite bushing直导套 Straight Guide Bush带肩导套 Shoulder Guide Bush顶针板导柱(中托司）Ejector Guide Pin (EGP)顶针板导套Ejector Guide Bush定位环 Locating Ring唧嘴Sprue bushing弹簧Spring回针Return PinKO杆KO Rod撑头Support Pillar垃圾钉 Stop pin限位块 Stop Block限位开关 Limits switch前模Cavity后模Core镶件Insert镶针Insert Pin互换镶件/针 Interchangeable insert/pin日期章 Dating insert环保章 Recycling Insert材料标示 Material symbol公司标志 Company logo型腔号 Cavity number行位镶件 Slide Insert波子螺丝 Ball-catch铲鸡Wedge压块Guide Rall斜导柱 Angle Pin耐模块 Wear Plate导向块 Guide Block限位螺丝 Stop Bolt行位扣 Slide Lock斜顶Lifter斜顶座 Lifter Base斜顶导向块Lifter Guide Block直身锁 Side lock斜度锁 Interlock内六角螺丝S.H.C.S平头螺丝 P.H.C.S无头螺丝 Screw Plug销钉Dowel Pin隔热板 Insulator plate塑料Plastic样板Sample产品Part/product标准件 Standard parts透明Transparence钢料Steel预硬钢材 Pre-harden steel铜公Copper electrode样板模 Prototype mold生产模 Production mold3D图3D Date2D图2D Drawing设计Design制造Manufacture/Build up/Construction 检验Check/Inspection测量Measure修改Change/Modify/correction质量Quality数量Quantity基准Datum/Reference点 Point线 Line面 Face表面Surface外观面 Appearance surface壁厚Wall thickness骨位Rib孔 Hole柱位Boss角 Corner圆角Fillet倒角Chamfer尖角Sharp corner斜度Angle / Taper凹槽Recess /Groove加硬Hardening回火Tempering氮化Nitriding电镀Plating镀铬Chroming晒纹Texture镜面抛光 Mirror finishing记数器 Shot counter天车Crane油石Oil stone分度盘 Rotary table码铁Clamping device烧焊Welding避空Gap / Clearance油槽Oil groove具专业英語模具专业英语入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate 圆形流道：round(full/half runner流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue 热流道板：hot manifold发热管：cartridge heater 探针: thermocouples插头：connector plug 插座：connector socket密封/封料：seal三、运水：water line 喉塞：line lpug喉管：tube塑胶管：plastic tube 快速接头：jiffy quick connectorplug/socker四、模具零件：mold components三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin顶针板：ejector retainner plate 托板：support plate螺丝：screw 管钉：dowel pin开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve司筒针：ejector pin 推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）：mold base 上内模：cavity insert下内模：core insert 行位（滑块）：slide镶件：insert 压座/斜鸡：wedge耐磨板/油板：wedge wear plate 压条：plate撑头: support pillar 唧嘴：sprue bushing挡板：stop plate 定位圈：locating ring锁扣：latch 扣鸡：parting lock set推杆：push bar 栓打螺丝：S.H.S.B顶板：eracuretun 活动臂：lever arm分流锥：spure sperader 水口司:bush垃圾钉：stop pin 隔片：buffle弹弓柱：spring rod 弹弓:die spring中托司：ejector guide bush 中托边：ejector guide pin镶针：pin 销子：dowel pin波子弹弓：ball catch模具成形不良用语英汉对照aberration 色差atomization ?化bank mark ?料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡 blooming 起霜low hole 破孔 blushing 泛白body wrinkle 侧壁皱纹 breaking-in 冒口带肉bubble 膜泡burn mark 糊斑 burr 毛边camber 翘曲cell 气泡 center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷 clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹各式模具分类用语英汉对照landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模各种模具常用成形方式英汉对照accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模机械类常用英语：冲压模具-零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块机械类常用英语：冲压模具-模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板冲压模具-冲压名称类英汉对照plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量模具工程常用词汇英汉对照——3high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程常用词汇英汉对照——2stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁模具工程常用词汇英汉对照die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门模具钢材及零件英语模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板零件英语punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣sprue lock pin料头钩销(拉料杆) 塑件模具相关英文——10eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣塑件模具相关英文——9compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具encapsulation molding低压封装成型、射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕模具相关英语——8stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块模具相关英语——7emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱模具相关英语——6drill钻boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边模具相关英语——5spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave 凹convex凸short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨模具相关英语——4baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型模具相关英语——3difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板模具相关英语——2steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机钟work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量模具相关英语——1padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱。
模具专业英语词汇-
模具专业英语词汇landed plunger mold 有肩柱塞式模具burnishing die 挤光模英语站landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具injection mold 注塑模rubber molding 橡胶成形hot chamber die casting 热室压铸sand mold casting 砂模铸造extrusion mold 挤出模multi-cavity mold 多模穴模具palletizing die 叠层模plaster mold 石膏模three plates mold 三板模plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模runner system浇道系统sprue/cold material trap 浇道/冷料井sprue puller 拉杆runner design 流道制定main runner 主流道secondary runner 次流道gate design 浇口制定submarine gate 埋伏浇口tunnel gate 隧道式浇口pinpoint gate 点浇口fan gate 扇形浇口side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口dish gate 盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣insulated runner/hot runner 热浇道runner plat 浇道模块valve gate阀门浇口slag well 冷料井cold slag 冷料渣sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) 注塑缺陷：flash 飞边warpage 翘曲air trap 积风blush 发赤flow line 流痕splay 银纹short shot 短射sink mark 缩痕streak 条纹void 缩孔weld line 熔接线gas mark 烧焦cold slug 冷斑delamination 起皮burr 毛刺flaw/scratch 刮伤gloss 光泽glazing 平滑surface check 表面裂痕hesitation 迟滞注塑工艺:molding conditions 成型条件drying 烘干barrel temperature 料筒温度melt temperature 熔化温度mold temperature 模具温度injection pressure 注塑压力back pressure 背压injection speed 注塑速度screw speed 螺杆转速tensile strength 抗拉强度tensile elongation 延伸率flexural modulus 弯曲模数flexural strength 抗弯强度shrinkage 收缩率regrind usage 次料使用机械设备:lathe车床planer |刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机punching machine 冲床robot机械手common equipment常用设备EDM=Electron Discharge Machining 放电加工3D coordinate measurement 三次元量床boring machine 搪孔机milling machine 铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床cylindrical grinding machine 外圆磨床die spotting machine 合模机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床模具零件:top plate上托板〔顶板〕top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 强化筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate 唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot 撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机〔尼龙拉勾〕：nylon latch lock斜顶：lifter模胚〔架〕： mold base上内模：cavity insert下内模：core insert行位〔滑块〕： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate 不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步〔正式〕模图制定：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极〕：copper electrodAabrasion n. 磨损mósǔnabrasion resistance n. 耐磨损性 nài mósǔn xìngabrasive n. 磨料 móliàoaccelerator n. 促进剂 cùjìnjìaccuracy n. 准确性zhǔnquèxìngacrylic n. 丙烯酸bǐngxīsuān，压克力yākelìadditive n. 添加剂tiānjiājìadhere v. 黏附 niánfùadhesion n. 黏合 niánhéadhesive n. 胶粘剂jiāozhānjìair entrapment n. 困气 kùnqìanneal v. 退火tùihuǒassemble v. 总成zǒngchéngBbarrel n. 机筒jītǒng，料筒liàotǒngblow molding n. 吹塑成型chūisù chéngxíngblow molding machine n. 吹塑机chūisùjībrittle adj. 脆性 cùixìngbubble n. 气泡 qìpàoby-product n. 副产品fùchǎnpǐnCcalendering n. 压延yāyáncarbon steel n. 碳素钢 tànsùgāngcasting n. 铸造 zhùzàocatalyst n. 催化剂cūihuàjìcavity n. 型腔xíngqiāngchemical resistance n. 耐化学腐蚀性 nài huàxuéfǔshí xìngchip v. 削xiāo，凿 záoclamping force n. 锁模力suǒmólìclamping tonnage n. 锁模吨位suǒmódūnwèicomputer aided design (CAD) n. 电脑辅助制定diànnǎo fǔzhù shèjìcomputer aided manufacture (CAM) n. 电脑辅助制造diànnǎo fǔzhù zhìzào computer numerical control (CNC) n. 电脑数字控制diànnǎo shùzì kòngzhìceramic n. 陶瓷 táocícold rolled steel n. 冷轧圆钢lěng zháyuán gāngcold runner n. 冷流道lěng liúdàocolorant n. 着色剂 zhuósèjìcomposite n. 复合材料 fùhé cáiliàocompression strength n. 抗压强度kàngyā qiángdùcooling channel/circuit n. 冷却管道lěngquèguǎndàocooling rate n. 冷却速率lěngq uèsùlǜcore n. 型芯xíngxīn，模芯móxīncorrosion n. 腐蚀fǔshícorrosion resistance n. 耐腐蚀性 nài fǔshí xìngcure v. 固化 gùhuàcustom adj. 定制 dìngzhìcycle time n. 循环时间 xúnhuán shíjiānDdegassing n. 排气 páiqìdensity n. 密度 mìdùdeform v. 变形 biànxíngdie n. 冲模 chòngmódie casting n. 压铸yāzhù，模铸 mózhùdimension n. 尺寸chǐcùndimensional tolerance n. 尺寸公差chǐcùn gōngchàdistort v. 扭曲niǔqūdraft angle n. 拨模斜度bōmó xiédùdwell time n. 驻留时间 zhùliúshíjiāndye n. 染料 ránliàoEejector mark n. 顶出痕迹dǐngchū hénjìejection pin n. 顶出杆dǐngchūgān，推顶锁tūidǐng suǒ，脱模锁tuōmósuǒejection plate n. 推顶板tūidǐng bǎn，脱模板tuōmóbǎnejection rod n. 脱模板拉杆tuōmóbǎn lāgānelastomer n. 弹性体tánxìngtǐelectrical discharge machining (EDM) n. 电火花加工diànhuǒhuājiāgōng epoxy n. 环氧树脂huányǎngshùzhīextruder n. 挤出机jǐchūjīextrusion n. 挤出jǐchū，挤塑jǐsùFfabricate v. 制造 zhìzàofiber n. 纤维xiānwéifiberglass n. 玻璃纤维bōli xiānwéifiber reinforcement n. 纤维加强xiānwéi zēngqiángfilm n. 薄膜 báomófire retardant n. 阻燃剂zǔránjìflash n. 溢料 yìliàoflow mark n. 流痕 liúhénflow rate n. 流动速率 liúdòng sùlǜfluorescent adj. 荧光yíngguāngfluorescent brightener n. 荧光增白剂yíngguāng zēngbáijìfoam n. 泡沫 pàomòfuse v. 熔合 rónghéGgas assisted injection molding n. 气辅注射成型qìfǔ zhùshè chéngxíng gate n. 浇口jiāokǒugate mark n. 浇口痕jiāokǒu héngear n. 齿轮chǐlúngrinder n. 研磨机yánmójī，磨床 móchuángHheat conduction n. 热传导 rè chuándàoheater band n. 加热圈jiārèquānheat treatment n. 热处理 rèchǔlǐhigh density polyethylene (HDPE) n. 高发度聚乙烯gāo mìdùjùyǐxīhigh impact plastic n. 高抗冲塑料gāo kàngchòng sùliàohigh impact polystyrene n. 高抗冲聚苯乙烯gāo kàngchòng jùběnyǐxīhobbing n. 滚铣gǔnxǐ，挤压制模jǐyā zhìmó，切压制模qiēyā zhìmóholding n. 保压bǎoyāhot runner n. 热流道 rè liúdàoIimpact strength n. 冲击强度chòngjī qiángdùinjection n. 注射 zhùshè，注塑 zhùsùinjection molding n. 注塑成型 zhùsù chéngxínginjection molding machine n. 注塑机zhùsùjīinjection pressure n. 注塑压力 zhùsùyālìinsulated runner n. 绝热流道 juérè liúdào，保温流道bǎowēn liúdào insulation layer n. 绝热层 juérè cénginternally heated runner n. 内加热流道 nèi jiārè liúdàointernal void n. 内部空腔 nèibùkōngqiāngJjoint n. 接头jiētóu，连接liánjiēLlaser n. 激光jīguānglaser cutter n. 激光切割机jīguāng qiēgējīlathe n. 车床chēchuánglocating pin n. 定位锁 dìngwèi suǒlow density polyethylene n. 低密度聚乙烯dī mìdùjùyǐxīMmelt v. 熔融 róngróngmelt index n. 熔融指数 róngróng zhǐshùmill (metal) v. 铣xǐmachining n. 机加工jījiāgōngmachining path n. 加工路径jiāgōng lùjìng manufacture v. 制造 zhìzàomeld line n. 融合线 rónghé xiànmetal machining n. 金属加工jīnshùjiāgōngmilling machine n. 铣床xǐchuángmodel n. 模型 móxíngmonomer n. 单体dāntǐmold n. 模具 mójùmold cavity n. 模具型腔 mójùxíngqiāngmold life n. 模具寿命 mójù shòumìngmulticavity mold n. 多腔模具duōqiāng mójùmulticolor injection molding n. 多色注塑duōsè zhùsùmultigate mold n. 多浇口模具duōjiāokǒu mójùmultishot injection molding n. 多色注塑duōsè zhùsùNnozzle n. 喷嘴pēnzǔiNylon n. 尼龙 NílóngOoxidation resistance n. 耐氧化性 nài yǎnghuà xìng oxidize v. 氧化yǎnghuàPpackaging n. 包装bāozhuāngpacking n. 补料bǔliàoparison n. 型坯xíngpīpart n. 零件 língjiànparting line n. 分模线fēnmóxiànparting plane n. 分模面fēnmómiànpinhole gate n. 针孔形浇口zhēnkǒngxíng jiāokǒuplastic n. 塑料 sùliàoplasticity n. 塑性 sùxìngplasticizer n. 增塑剂zēngsùjìplotter n. 绘图机hùitújīpolish v. 抛光pāoguāngpolycarbonate (PC) n. 聚碳酸酯jùtànsuānzhǐpolyethylene n. 聚乙烯jùyǐxīpolyester n. 聚酯jùzhǐpolymer n. 聚合物〔体〕jùhéwù(tǐ)，高聚物gāojùwùpolymerization n. 聚合 jùhépolystyrene n. 聚苯乙烯jùběnyǐxīpolyurethane n. 聚氨脂jù'ānzhīpolyvinyl chloride (PVC) n. 聚氯乙烯jùlǜyǐxīporous adj. 多孔duōkǒngprecise adj. 精密jīngmìprecision n. 精度jīngdùprecision injection machine n. 精密注塑机jīngmìzhùsùjīprecision molding n. 精密模塑jīngmì mósùpreform n. 预成型 yùchéngxíngpreform molding n. 预成型模塑 yùchéngxíng mósùprocess v. 处理chǔlǐ；加工jiāgōngproduction line n. 生产线shēngchǎnxiànprototype n. 原型 yuánxíngpunch n. 冲头 chòngtóuQquench v. 淬火cùihuǒRregrind n. 回用料 húiyòngliàoresin n. 树脂shùzhīrib n. 肋条 lèitiáorib stiffener n. 强化肋jiāqiáng lèirigidity n. 刚性gāngxìngripple n. 波纹bōwén，皱纹 zhòuwénrough adj. 粗糙cūcāorubber n. 橡胶xiàngjiāo；橡皮 xiàngpírunner n. 流道 liúdàorunnerless adj. 无流道 wúliúdàorunnerless injection mold n. 无流道注塑模具 wúliúdào zhùsù mójùSscale n. 比例bǐlìschematic n. 图解tújiěseal v. 密封mìfēn gshort shot n. 短射duǎnshè，欠料注射 qiànliào zhùshèshot n. 注料 zhùliào，注射 zhùshèshot size n. 注塑量 zhùsùliàngshrinkage n. 收缩shōusuōside core n. 侧性芯cèxìngxīnside gate n. 侧向浇口 cèxiàng jiāokǒusilicone n. 聚硅氧烷jùgūiyǎngwánsilicone rubber n. 硅橡胶gūixiàngjiāosimulate v. 模拟mónǐsingle cavity mold n. 单腔模具dān qiāng mójùsingle gate mold n. 单浇口模具dān jiāokǒu mójùsink mark n. 凹痕āohén，缩痕suōhénslide n. 滑动阀 huádòngfásoftener n. 软化剂ruǎnhuàjìsprue n. 注道 zhùdàosteam channel n. 汽道 qìdàostabilizer n. 稳定剂wěndìngjìstamping n. 冲压chòngyāstainless steel n. 不锈钢bùxiùgāngstrain n. 应变 yìngbiànstreak n. 条纹 tiáowén，条痕 tiáohénstress n. 应力 yìnglìstripper n. 脱模器tuōmóqì，顶出器dǐngchūqìstripper ring n. 脱模圈tuōmóquānsurface defect n. 表面缺陷biǎomiàn quēxiànsurface treatment n. 表面处理biǎomiàn chǔlǐsymmetrical adj. 对称dùichēngsymmetry n. 对称dùichēngTtie bar n. 连接杆liánjiēgānTeflon n. 特氟隆 Tèfúlóngtemper v. 回火hùihuǒtensile strength n. 抗张强度kàngzhāng qiángdùthermoforming n. 热成型 rèchéngxíngthermoplastic n. 热塑性塑料 rèsùxìng sùliào adj. 热塑性 rèsùxìng thermoset n. 热固性塑料 règùxìng sùliào adj. 热固性 règùxìngthree-dimensional adj. 三维空间sānwéi kōngjiāntolerance n. 公差gōngchàtool mark n. 刀痕dāohéntool steel n. 工具钢gōngjùgāngUultrasonic welder n. 超声波焊接机chāoshēngbōhánjiējīundercut n. 凹孔āokǒngunit cost n. 单价dānjiàVvacuum n. 真空zhēnkōngvented injection molding n. 排气式注塑成型 páiqìshì zhùsù chéngxíng viscosity n. 黏度 niándù，黏性 niánxìngvulcanize v. 硫化 liúhuàWwarpage n. 翘曲变形qiàoqū biànxíngwear n. 磨损mósǔnwear resistance n. 耐磨损性 nài mósǔn xìngweld line n. 熔接线róngjiē xiànworking drawing n. 工程图依据国家标准，以下为部分塑料模具成形术语的标准翻译。
模具专业英语术语
中文 模具设计术语 三板模 二板模 高光蒸汽注塑模 气体辅助成型模具 双物料成形模具 叠层模具 低压注塑模具 镁、铝合金压铸模具 SMC热压模具 通用模具 单腔模具 多腔模具 组合模 注射模 热固性塑料模 热塑性塑料模 双色模 试验模 正式模 快速模 英文 3-plate mold 2-plate mold High Class Steam Injection Mold Gas Assisted Injection Mold 2 K Injection Mold Stack Mold Low Presure Injection Mold Mg & AI Die-Casting Mold SMC Mold universal mold single cavity mold multi cavity mold segment mold injection mould mould for thermosets mould for thermoplastics 2-shot molding Trial mold Production mold Prototype mold 欧洲习语 美国习语 备注
浇道系统 冷料井 射料浇口/直浇口 侧浇口 侧缘浇口 搭接浇口 薄膜浇口 闸门浇口 缝隙浇口 扇形浇口 盘形浇口 隔膜浇口 环形浇口 潜入式浇口 隧道式浇口 针点浇口 无浇道 水口形式 进入位 水口大小 转水口 唧嘴口径 主流道 分流道 浇口 护耳浇口 模具号 产品号 产品名称 产品材质 每啤重量 产品重量 成型周期 工程图 装配图 设计任务书 产品开发 目录 设计资料 附件 公制 英制 设计更改
runner system slag well / Cold-slug well sprue gate / Direct gate side gate edge gate tab gate film gate flash gate slit gate fan gate dish gate diaphragm gate ring gate subarine gate （sub marine gates） tunnel gate pin gate / Pin-point gate Runner less gate type gate location gate size switching runner/gate sprue diameter Sprue Runner Gate tab gate Tool number Part number Part Name Part material Shot weight Moulded part weight Cycle time procedure drawing assembly drawing master schedule Product development Contents Design documentation Attachments metric system Imperial Unit design modification
模具专业英语
模具英语词汇Mould English Word（一）Mould Engineering模具工程词汇一：入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二：流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三：运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plat 螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock四、模具零件：mold components顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位(滑块): slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin五．术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut hight 顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side 模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件：Do not use (core/cavity) insert 用铍铜做镶件：use beryllium copper insert 初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极)：copper electrode六：common vocabulary for die engineering 模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spring 弹簧bolt螺栓plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品ncoming material to be inspected进货待验description品名（二）Mould Tool制模工具词汇adjustable spanner 活动扳手angle cutter 角铣刀anvil 铁钻arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳顶plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手analog-mode device类模器die lifter举模器argon welding氩焊pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把/ mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座三）Defect in Molding成型缺陷词汇aberration 色差atomization 霚化bank mark 滞料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕flange wrinkle 凸缘起皱flaw 刮伤cell 气泡overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹shock line 模口挤痕critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格not up todimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screw head 螺丝滑头slipped screwhead/shippery screw thread 滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露ack of painting烤漆不到位qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料missing part漏件wrong part错件excessive defects过多的缺陷(四）Heat Treatment热处理词汇age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿扥木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理(五）Machine机床词汇punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |‘plein |刨床miller铣床grinder磨床driller钻床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机CNC/computerized numerical control 电脑锣/加工中心(六）Plastic Material塑胶原料名称词汇英文简称英文全称中文全称ABA Acrylonitrile-butadiene-acrylate 丙烯腈/丁二烯/丙烯酸酯共聚物ABS Acrylonitrile-butadiene-styrene 丙烯腈/丁二烯/苯乙烯共聚物AES Acrylonitrile-ethylene-styrene 丙烯腈/乙烯/苯乙烯共聚物AMMA Acrylonitrile/methyl Methacrylate 丙烯腈/甲基丙烯酸甲酯共聚物ARP Aromatic polyester 聚芳香酯AS Acrylonitrile-styrene resin 丙烯腈-苯乙烯树脂ASA Acrylonitrile-styrene-acrylate 丙烯腈/苯乙烯/丙烯酸酯共聚物CA Cellulose acetate 醋酸纤维塑料CAB Cellulose acetate butyrate 醋酸-丁酸纤维素塑料CAP Cellulose acetate propionate 醋酸-丙酸纤维素CE Cellulose plastics, general 通用纤维素塑料CF Cresol-formaldehyde 甲酚-甲醛树脂CMC Carboxymethyl cellulose 羧甲基纤维素CN Cellulose nitrate 硝酸纤维素CP Cellulose propionate 丙酸纤维素CPE Chlorinated polyethylene 氯化聚乙烯CPVC Chlorinated poly(vinyl chloride) 氯化聚氯乙烯CS Casein 酪蛋白CTA Cellulose triacetate 三醋酸纤维素EC Ethyl cellulose 乙烷纤维素EMA Ethylene/methacrylic acid 乙烯/甲基丙烯酸共聚物EP Epoxy, epoxide 环氧树脂EPD Ethylene-propylene-diene 乙烯-丙烯-二烯三元共聚物EPM Ethylene-propylene polymer 乙烯-丙烯共聚物EPS Expanded polystyrene 发泡聚苯乙烯ETFE Ethylene-tetrafluoroethylene 乙烯-四氟乙烯共聚物EVA Ethylene/vinyl acetate 乙烯-醋酸乙烯共聚物EVAL Ethylene-vinyl alcohol 乙烯-乙烯醇共聚物FEP Perfluoro(ethylene-propylene) 全氟（乙烯-丙烯）塑料FF Furan formaldehyde 呋喃甲醛HDPE High-density polyethylene plastics 高密度聚乙烯塑料HIPS High impact polystyrene 高冲聚苯乙烯IPS Impact-resistant polystyrene 耐冲击聚苯乙烯LCP Liquid crystal polymer 液晶聚合物LDPE Low-density polyethylene plastics 低密度聚乙烯塑料LLDPE Linear low-density polyethylene 线性低密聚乙烯LMDPE Linear medium-density polyethylene 线性中密聚乙烯MBS Methacrylate-butadiene-styrene 甲基丙烯酸-丁二烯-苯乙烯共聚物MC Methyl celluloseMDPE Medium-density polyethylene 中密聚乙烯MF Melamine-formaldehyde resin 密胺-甲醛树脂MPF Melamine/phenol-formaldehyde 密胺/酚醛树脂PA Polyamide (nylon) 聚酰胺（尼龙）PAA Poly(acrylic acid) 聚丙烯酸PADC Poly(allyl diglycol carbonate) 碳酸-二乙二醇酯·烯丙醇酯树脂PAE Polyarylether 聚芳醚PAEK Polyaryletherketone 聚芳醚酮PAI Polyamide-imide 聚酰胺-酰亚胺PAK Polyester alkyd 聚酯树脂PAN Polyacrylonitrile 聚丙烯腈PARA Polyaryl amide 聚芳酰胺PASU Polyarylsulfone 聚芳砜PAT Polyarylate 聚芳酯PAUR Poly(ester urethane) 聚酯型聚氨酯PB Polybutene-1 聚丁烯-[1]PBA Poly(butyl acrylate) 聚丙烯酸丁酯PBAN Polybutadiene-acrylonitrile 聚丁二烯-丙烯腈PIB Polyisobutylene 聚异丁烯PISU Polyimidesulfone 聚酰亚胺砜PMCA Poly(methyl-alpha-chloroacrylate) 聚α-氯代丙烯酸甲酯PMMA Poly(methyl methacrylate) 聚甲基丙烯酸甲酯PMP Poly(4-methylpentene-1) 聚4-甲基戊烯-1PMS Poly(alpha-methylstyrene) 聚α-甲基苯乙烯POM Polyoxymethylene, polyacetal 聚甲醛PP Polypropylene 聚丙烯PPA Polyphthalamide 聚邻苯二甲酰胺PPE Poly(phenylene ether) 聚苯醚PPO Poly(phenylene oxide) deprecated 聚苯醚PPOX Poly(propylene oxide) 聚环氧（丙）烷PPS Poly(phenylene sulfide) 聚苯硫醚PPSU Poly(phenylene sulfone) 聚苯砜PS Polystyrene 聚苯乙烯PSU Polysulfone 聚砜PTFE Polytetrafluoroethylene 聚四氟乙烯PUR Polyurethane 聚氨酯PVAC Poly(vinyl acetate) 聚醋酸乙烯PVAL Poly(vinyl alcohol) 聚乙烯醇PVB Poly(vinyl butyral) 聚乙烯醇缩丁醛PVC Poly(vinyl chloride) 聚氯乙烯PVCA Poly(vinyl chloride-acetate) 聚氯乙烯醋酸乙烯酯PVDC Poly(vinylidene chloride) 聚（偏二氯乙烯）PVDF Poly(vinylidene fluoride) 聚（偏二氟乙烯）PVF Poly(vinyl fluoride) 聚氟乙烯PVFM Poly(vinyl formal) 聚乙烯醇缩甲醛PVK Polyvinylcarbazole 聚乙烯咔唑PVP Polyvinylpyrrolidone 聚乙烯吡咯烷酮S/MA Styrene-maleic anhydride plastic 苯乙烯-马来酐塑料SAN Styrene-acrylonitrile plastic 苯乙烯-丙烯腈塑料SB Styrene-butadiene plastic 苯乙烯-丁二烯塑料Si Silicone plastics 有机硅塑料SMS Styrene/alpha-methylstyrene plastic 苯乙烯-α-甲基苯乙烯塑料SP Saturated polyester plastic 饱和聚酯塑料SRP Styrene-rubber plastics 聚苯乙烯橡胶改性塑料TEEE Thermoplastic Elastomer,Ether-Ester 醚酯型热塑弹性体TEO Thermoplastic Elastomer, Olefinic 聚烯烃热塑弹性体（七）Steel for Mold模具钢材词汇alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 预硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板（八）Punch Press冲压词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to. to send delinery back to retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑。
模具标件专业英语词汇
模具标件专业英语词汇一、模具（Mold）相关基础词汇。
1. Mold [məʊld] - 名词，模具；也可作动词，塑造，浇铸。
- 例句：This is a new type of injection mold.（这是一种新型的注塑模具。
）2. Die [daɪ] - 名词，冲模，钢模（在冲压工艺中使用）- 例句：The die is used for stamping metal sheets.（这个冲模用于冲压金属薄板。
）3. Cavity ['kævəti] - 名词，型腔；洞，凹处。
- 发音：['kævəti]- 例句：The cavity of the mold should be polished carefully.（模具的型腔应该仔细抛光。
）4. Core [kɔː(r)] - 名词，型芯；核心。
- 例句：The core is an important part of the mold.（型芯是模具的一个重要部分。
）二、模具标件（Standard Mold Components）词汇。
1. Guide Pin ['ɡaɪ d pɪn] - 名词，导柱。
- 例句：The guide pin helps to align the two parts of the mold.（导柱有助于使模具的两个部分对齐。
）2. Guide Bushing ['ɡaɪ d 'bʊʃɪŋ] - 名词，导套。
- 例句：The guide bushing is used in combination with the guide pin.（导套与导柱配合使用。
）3. Ejector Pin [i'dʒektə pɪn] - 名词，顶针。
- 例句：The ejector pin is used to push the finished product out of the mold.（顶针用于将成品从模具中顶出。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
模具钢材hard alloy steel超硬合金鋼hot work die steel熱鍛模用鋼low alloy tool steel特殊工具鋼low manganese casting steel低錳鑄鋼marging steel馬式體高強度熱處理鋼martrix alloy馬特里斯合金meehanite cast iron米漢納鑄鋼meehanite metal米漢納鐵merchant iron市售鋼材molybdenum high speed steel鉬係高速鋼m olybdenum steel鉬鋼nickel chromium steel鎳鉻鋼prehardened steel頂硬鋼silicon steel sheet矽鋼板stainless steel不銹鋼tin plated steel sheet鍍錫鐵板tough pitch copper 韌銅troostite吐粒散鐵tungsten steel钨鋼vinyl tapped steel sheet塑膠覆面鋼板模具常用之工作机械3D coordinate measurement三次元量床boring machine搪孔機cnc milling machine CNC銑床contouring machine輪廓鋸床copy grinding machine仿形磨床copy lathe仿形車床copy milling machine仿形銑床copy shaping machine仿形鉋床cylindrical grinding machine外圓磨床die spotting machine合模機drilling machine钻孔機engraving machine雕刻機engraving E.D.M雕模放置加工機form grinding machine成形磨床graphite machine石墨加工機horizontal boring machine臥式搪孔機horizontal machine center臥式加工製造中心internal cylindrical machine內圓磨床jig boring machine冶具搪孔機jig grinding machine冶具磨床lap machine研磨機machine center加工製造中心multi model miller靠磨銑床NC drilling machine NC鑽床NC grinding machine NC磨床NC lathe NC車床NC programming system NC程式製作系統planer龍門鉋床profile grinding machine投影磨床projection grinder投影磨床模具常用之工作机械copy shaping machine 仿形鉋床cylindrical grinding machine 外圓磨床d ie spotting machine 合模機drilling machine 钻孔機e ngraving machine 雕刻機engraving E.D.M. 雕模放置加工機f orm grinding machine 成形磨床graphite machine 石墨加工機h orizontal boring machine 臥式搪孔profile grinding machine投影磨床projection grinder投影磨床radial drilling machine旋臂钻床shaper牛頭鉋床surface grinder平面磨床try machine試模機turret lathe轉塔車床universal tool grinding machine 萬能工具磨床vertical machine center立式加工製造中心wire E.D.M.線割放電加工機各种模具常用成形方式accurate die casting精密壓鑄powder forming粉末成形calendaring molding壓延成形powder metal forging粉末鍛造cold chamber die casting冷式壓鑄precision forging精密鍛造cold forging冷鍛press forging沖鍛compacting molding粉末壓出成形rocking die forging搖動鍛造compound molding複合成形rotary forging迴轉鍛造compression molding壓縮成形rotational molding離心成形dip mold浸漬成形rubber molding橡膠成形encapsulation molding注入成形sand mold casting砂模鑄造extrusion molding擠出成形shell casting殼模鑄造foam forming发泡成形sinter forging燒結鍛造forging roll軋鍛six sides forging六面鍛造gravity casting重力鑄造slush molding凝塑成形hollow(blow) molding中空(吹出)成形squeeze casting高壓鑄造hot chamber die casting熱室壓鑄swaging 擠鍛hot forging熱鍛transfer molding轉送成形injection molding射出成形warm forging溫鍛investment casting精密鑄造matched die method對模成形法laminating method被覆淋膜成形low pressure casting低壓鑄造lost wax casting脫蠟鑄造matched mould thermal forming對模熱成形模各式模具分類用語bismuth mold鉍鑄模landed plunger mold有肩柱塞式模具burnishing die擠光模landed positive mold有肩全壓式模具button die鑲入式圓形凹模loading shoe mold料套式模具center-gated mold中心澆口式模具loose detail mold活零件模具chill mold冷硬用鑄模loose mold活動式模具clod hobbing冷擠壓製模louvering die百葉窗沖切模composite dies複合模具manifold die分歧管模具counter punch反击模modular mold組合式模具double stack mold雙層模具multi-cavity mold多模穴模具electroformed mold電鑄成形模multi-gate mold複式澆口模具alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板arbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣sprue lock pin料头钩销(拉料杆) aberration 色差atomization 自动化bank mark 料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crazing 碎裂crazing 龟裂edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 击缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针: ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core, return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：sprue spreader水口司:bush垃圾钉：stop pin 隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin承压平面平衡：parting surface support balance 模排气：parting line venting回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate, core direct cut on B-plate.不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliminary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability, stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thermo expansion铜公(电极）：copper electrode。