关于ATE校准配置文件说明

关于ATE校准工具说明
ATE主要用于射频校准与综测，对射频性能进行优化，使其符合通信标准。

其主要包括三个文件，setup.ini, cal.INI和.CFG文件。

由于器件或SMT差异可能导致校准出现一定偏差，这时可以通过修改这三个文件里面一些参数进行修正处理。

setup.ini文件主要是针对校准以及测试参数，环境的设置；
CAL.INI文件主要是对校准参数的一些设置；
CFG文件主要是对校准的规格以及参数设置；
现在下面分别对这三个文件进行说明，其中标红色部分，可以根据情况进行适当调整。

Set.ini文件：
[Reset RF Function Group]
GSM900 Sig = 0
GSM1800 Sig = 1
GSM1900 Sig = 1
GSM900 NSig = 1
GSM1800 NSig = 1
GSM1900 NSig = 1
[System Setting]
External Reference Clock = 0
CMU Base GPIB Address = 20
Instrument = "AG8960"
Power Supply Address = 5
CMU RF Port = 2
Debug Mode = 1
Test Mode = 0
FDM database file Line0001 = "d:\\HW\\MT190\\SW\\MT170.F.HX8312A.V1.6\\BPLGUInfoCustomSrcP_MT6225_S00_F_HX 8312"
FDM database file Line0002 = "A_V1_6"
Calibration file = "d:\\HW\\MT190\\CFG\\MT6139_RFMD.ini"
Config file = "d:\\HW\\MT190\\CFG\\Meta_MT6229_40D.CFG"
Report file path = "d:\\HW\\MT190\\REP"
Database file = "c:\\Program Files\\MTK_atedemo\\mtk_ate.xls"
IMSI = "001010123456789"
POWER ON AFTER CHANGE = 1
Stability Count = 1
Check Testfixture = 0
Fixture COM port = 6
System Cable Loss Calibration = 0
System Input Calibration = 1
System Output Calibration = 1
Special Power Control = 1
Special Power Delay = 5
ANRITSU ME7413A = 0
ATD112 Send After Time = 5 此为开机拨号时间延迟，根据量产情况可以调整为4或6 ATD112 Check Connect Delay Time = 1.5
CMU GPIB BOARD = 0
N4010A Address = 15
MT8852B Address = 27
Instrument WiFi = "N4010A"
Instrument BT = "MT8852B"
[Call Setup Configuration]
Setup Network = 1
GSM Call Setup Channel = 1
GSM BCCH Channel = 32
DCS Call Setup Channel = 512
DCS BCCH Channel = 700
PCS Call Setup Channel = 512
PCS BCCH Channel = 700
BCCH RF LEVEL = -60
BS TCH LEVEL = -81
Triple Band = 0
GPRS TEST = 0
MSlot0 Downlink = 0
MSlot1 Downlink = 0
MSlot2 Downlink = 0
MSlot3 Downlink = 1
MSlot4 Downlink = 1
MSlot5 Downlink = 1
MSlot6 Downlink = 1
MSlot7 Downlink = 0
MSlot0 Uplink = 0
MSlot1 Uplink = 0
MSlot2 Uplink = 0
MSlot3 Uplink = 1
MSlot4 Uplink = 0
MSlot5 Uplink = 0
MSlot6 Uplink = 0
MSlot7 Uplink = 0
MSlot0 Relative Level = 0
MSlot1 Relative Level = 0
MSlot2 Relative Level = 6
MSlot3 Relative Level = 0
MSlot4 Relative Level = 6
MSlot5 Relative Level = 6
MSlot6 Relative Level = 0
MSlot7 Relative Level = 0
MSlot0 Gamma = 3
MSlot1 Gamma = 3
MSlot2 Gamma = 3
MSlot3 Gamma = 3
MSlot4 Gamma = 3
MSlot5 Gamma = 3
MSlot6 Gamma = 3
MSlot7 Gamma = 3
BLER Reference Level = -85 Individual Level BLERS0 = 0 Individual Level BLERS1 = 0 Individual Level BLERS2 = -2 Individual Level BLERS3 = -10 Individual Level BLERS4 = 0 Individual Level BLERS5 = 0 Individual Level BLERS6 = 0 Individual Level BLERS7 = 0 RLC Blocks = 1000
DCS Band = 1
GSM Band = 1
GSM850 Band = 0
GSM850 Call Setup Channel = 128 GSM850 BCCH Channel = 128 Triband Test Type = 0
[Signalling Measurement]
Power Measment Burst = 10 Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 1
Timing Error = 1
Modulation Measment Burst = 10 Phase Error Peak = 1
Phase Error RMS = 1 Frequency Error = 1
ORFS MOD Burst = 10 Spectrum Modulation = 1
ORFS Switch Burst = 10 Spectrum Switch = 1
Rx Quality = 1
RX Level = 1
RFER = 0
BBB = 1
GSM Rx Meas Level = -100
DCS Rx Meas Level = -100
PCS Rx Meas Level = -100
Rx RFER Burst = 128
Rx BBB Burst = 88
GSM Output Loss = 0.5
GSM Input Loss = 0.5
DCS Out Loss = 0.7000000000000001 DCS Inp Loss = 0.7000000000000001 PCS Out Loss = 0.8
PCS Inp Loss = 0.8
Location update timeout = 60
Timing Error Limit = 5
RX Level Limit = 26
RX Quality Limit = 3
Stop Condition = 0
Version New = 0
Final Test With Calibration = 1 Wireless Test = 0
Get Barcode = 0
Manual Check Ber Limit = 1
RX ClassII Limit = 1.5
RX ClassIb Limit = 1.5
Default Test Items = 1
Test Fixture = 1
Code Scheme = 9
Check BarCode Delay = 5
GPRS TEST MODE = 2
Handover Delay time = 0.5
BER MEAS MODE = 0
BER Continuous Meas Delay = 1.5 Mobile Repore RxQ Delay = 1.5
TX Limit Check by Tester = 1
Write pass status to Target = 0
MT Call = 0
GSM850 Rx Meas Level = -100 6218B Normal Baud Rate = 115200 6205B Normal Baud Rate = 57600 RX Level Limit MAX = 35
BLER Limit = 5.0
Change Dual Band Delay = 5.0 Change Single Band Delay = 15.0
BT Inp Loss = 4
BT Out Loss = 4
[Calibration Setup]
GSMN OUT LOSS = 0.5
GSMN INP LOSS = 0.5
DCSN OUT LOSS = 0.7000000000000001 DCSN INP LOSS = 0.7000000000000001 COM PORT = 4
Check IMEI = 0
Auto Barcode = 1
Auto Barcode Step = 1
ADC Calibration = 1
AG8960 GSM = 0
Power Supply Type = 2
Frequency Bank with PCS = 0
BB Chip Type = "AutoDetect"
CO GSM900 = 65
CO DCS1800 = 700
CO PCS1900 = 660
PCSN OUT LOSS = 0.8
PCSN INP LOSS = 0.8
Power Measurement Type = 0
Enter META Mode Timeout = 10000 Enter META Timer Delay = 2.0
AFC Calibration = 1
Pathloss Calibration = 1
APC Calibration = 1
APC Check = 1
Frequency Bank with GSM850 = 0 Frequency Bank with GSM900 = 1 Frequency Bank with DCS1800 = 1
Add Calibration Status = 0
Phase Error Calibration = 0
Secondary COM = 8
Third COM = 8
Calibration Second Power On = 5
Crystal AFC Calibration = 1
APC Calibration Full = 0
IP2 Calibration = 0
IP2 Calibration Type = 2
APC Calibration Sky77328 = 0
AFC CW = 0
TX DC Offset Calibration = 0
8PSK FULL = 0
APC EPSK Cal = 0
8PSK TYPE = 1
APC Calibration Renesas = 0
Skip Battery Calibration = 0
Skip Init PowerTable = 0
Skip Crystal TX Offset = 0
PathLoss Extra Delay = 0.2
WIFI TXDC Cal = 0
WIFI TXP Cal = 0
WIFI RF Check = 0
SKY APC DC Cal = 0
APC Extra Delay = 0.01
BT CAPID Cal = 0
[IMEI]
IMEI = 12345678901234
Scan IMEI = 0
[Final Test TX Check]
GSM900_MAX_P = "7.0,9.0,11.0,13.0,15,17.0,19.0,21.0,22.0,25.0,26.0,28.0,30.0,31.5,34.2," GSM900_MIN_P = "3.0,5.0,7.0,9.0,11.0,13.0,15.0,17.0,19.0,21.0,23.0,25.0,27.0,29.5,31.2," DCS1800_MAX_P = "3.0,3.5,5.5,7.5,9.5,12.0,14.0,16.0,18.0,19.0,21.0,23.0,25.0,27.0,28.5,31," DCS1800_MIN_P = "-2.5,0.5,3.0,5.0,7.0,9.0,11.0,13.0,15.0,17.0,17.5,21.0,23.0,25.0,26.5,27.5," PCS1900_MAX_P = "0.5,2.5,4.5,6.5,8.5,10.5,12.5,14.5,16.5,18.5,20.5,22.5,24.5,26.5,28.5,31.0," PCS1900_MIN_P = "-0.5,1.5,3.5,5.5,7.5,9.5,11.5,13.5,15.5,17.5,19.5,21.5,23.5,25.5,27.5,28.0," GSM850_EPSK_MAX_P = "6,8,10,12,14,16,18,20,22,24,26,27,27,27,27,"
GSM850_EPSK_MIN_P = "4,6,8,10,12,14,16,18,20,22,24,25.8,25.8,25.8,25.8,"
GSM900_EPSK_MAX_P = "6,8,10,12,14,16,18,20,22,24,26,27.8,27.8,27.8,27.8,"
GSM900_EPSK_MIN_P = "4,6,8,10,12,14,16,18,20,22,24,25.8,25.8,25.8,25.8,"
DCS1800_EPSK_MAX_P = "2,3.5,5,7,9,11,13,15,17,19,21,23,25,26.8,26.8,26.8,"
DCS1800_EPSK_MIN_P = "-0.5,1.5,3.5,5,7,9,11,13,15,17,19,21,23,24.8,24.8,24.8,"
PCS1900_EPSK_MAX_P = "2,3.5,5,7,9,11,13,15,17,19,21,23,25,26.1,26.1,26.1,"
PCS1900_EPSK_MIN_P = "-0.5,1.5,3.5,5,7,9,11,13,15,17,19,21,23,24.8,24.8,24.8,"
EPSK_95P_EVM = 15
EPSK_95P_MAGERR = 5
EPSK_95P_PHERR = 5
EPSK_EVM_PK = 30
EPSK_EVM_RMS = 9
EPSK_MAGERR_PK = 17.7
EPSK_MAGERR_RMS = 12.5
EPSK_PHERR_PK = 200
EPSK_PHERR_RMS = 5
EPSK_ORIG_OFFSET = -30.0
G850_Freq_Error_Limit = 85
GSM_Freq_Error_Limit = 90
DCS_Freq_Error_Limit = 180
PCS_Freq_Error_Limit = 190
Phase_Error_Peak_Limit = 20
Phase_Error_RMS_Limit = 5
AG8960_RF_Amptd_Freq_Offset Line0001 = "500000000,641000000,641100000,876000000,876100000,1312000000,1312100000,18800000" AG8960_RF_Amptd_Freq_Offset Line0002 = "00,1881000000,2000000000,"
AG8960_RF_Amptd_Value_Offset = "-0.5,-0.5,-0.5,-0.5,-0.5,-0.5,-0.7,-0.7,-0.8,-0.8,"
8960的校准综测线损在此修改，其值为负的。

CMU200的校准综测线损在configuration里面修改，其值为正。

Using AG8960 Amptd Offset = 1
Spectrum due to switching enable = "1,0,0,1,"
Spectrum due to modulation enable = "0,0,0,1,1,0,0,1,0,0,1,"
Spectrum due to switch limit = "-19.0,-19.0,-21.0,-21.0,-21.0,-21.0,-24.0,-24.0,"
GSM ORFS MOD Limit Line0001 = "0.5,0.5,-30.0,-30.0,-33.0,-33.0,-55.0,-55.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
GSM ORFS MOD Limit Line0002 = "-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
EPSK ORFS MOD Limit Line0001 = "0.5,0.5,-30.0,-30.0,-33.0,-33.0,-55.0,-55.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
EPSK ORFS MOD Limit Line0002 = "-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,"
WT4400 Coupling Loss = "801.0,0.6,1701.0,1.2,999.0,0.8,1999.0,1.3"
[Barcode]
Barcode = "01677"
Barcode Step = 1
Barcode Limit = "MT012345678901234569"
Barcode Length Limit = 0
Shop Floor Error Hit = 0
[Report Option]
Part Number = "MT6225"
Batch = "01"
Revision = "W05.24"
Serial Number = "000001"
Report Type Detail = 0
Crystal Vender = "unknow"
[Error Code]
Lacation update Fail = 101
MT Call Fail = 102
Call Drop = 103
Average Burst Power Fail = 104
Peak Burst Power Fail = 105
PVT Match Fail = 106
Timing Error Fail = 107
Phase Error Peak Fail = 108
Phase Error RMS Fail = 109
Frequency Error Fail = 110
Spectrum due to Switching Fail = 111
Spectrum due to Modulation Fail = 112
Rx Quality Fail = 113
Rx Level Fail = 114
BER Fail = 115
METAAPP_OPEN_UART_FAIL = 201
METAAPP_BOOT_FAIL = 202
METAAPP_COM_ERROR = 203
METAAPP_CONNECT_WITH_TARGET_FAIL = 204
METAAPP_DISCONNECT_WITH_TARGET_FAIL = 205 METAAPP_RF_SELECT_BAND_FAIL = 206
METAAPP_RF_AFC_MEASURE_FAIL = 207
METAAPP_RF_PM_FAIL = 208
METAAPP_RF_NB_TX_FAIL = 209
METAAPP_RF_SETBBTXCFG2_FAIL = 210
METAAPP_NVRAM_INIT_FAIL = 211
METAAPP_FILE_READ_FAIL = 212
METAAPP_IMEI_CALCULATE_CD_FAIL = 213
METAAPP_ADC_MEASURE_FAIL = 214
METAAPP_BB_REG_READ_FAIL = 215
METAAPP_GET_VERSION_INFO_FAIL = 216
METAAPP_FAT_OPEN_FAIL = 217
METAAPP_QUERY_TWO_APC_DC_OFFSET_SUPPORT_FAIL = 218 METAAPP_WIFI_SET_TXPOWER_FAIL = 219
METAAPP_WIFI_MAC_ADDRESS_FORMA T_FAIL = 220 METAAPP_BT_ADDRESS_FORMAT_FAIL = 221
METAAPP_TIMEOUT_FAIL = 222
BARCODE_LIMIT_FAIL = 306
AFC Calibration Fail = 501
Pathloss Calibration Fail = 502
APC Calibration Fail = 503
PHASE ERROR Calibration Fail = 504
ADC Calibration Fail = 505
BLER Fail = 116
IP2 Calibration Fail = 506
[GSM 1]
Active = 1
TCH = 975
PCL = 5
Output Loss = 0.5
Input Loss = 0.5
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 32.2 Gold Sample Rx Level = 29
BER measurement level = -105
BS TCH level = -81
RX Level Max Limit = 35
RX Level Min Limit = 27
EPSK MCS = 9
[GSM 2]
Active = 1
TCH = 62
PCL = 5
Output Loss = 0.5
Input Loss = 0.5
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 23.0
Gold Sample Rx Level = 29
BER measurement level = -105
BS TCH level = -81
RX Level Max Limit = 33
RX Level Min Limit = 27
EPSK MCS = 1
[GSM 3]
Active = 1
TCH = 124
PCL = 5
Output Loss = 0.5
Input Loss = 0.5
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 13.0 Gold Sample Rx Level = 29
BER measurement level = -105
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 27
EPSK MCS = 9
[GSM 4]
Active = 1
TCH = 975
PCL = 19
Output Loss = 0.5
Input Loss = 0.5
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 32.2 Gold Sample Rx Level = 29
BER measurement level = -105
BS TCH level = -81
RX Level Max Limit = 35
RX Level Min Limit = 27
EPSK MCS = 9
[GSM 5]
Active = 1
TCH = 62
PCL = 19
Output Loss = 0.5
Input Loss = 0.5
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 23.0 Gold Sample Rx Level = 29
BER measurement level = -105
BS TCH level = -81
RX Level Max Limit = 33
RX Level Min Limit = 27
EPSK MCS = 1
Active = 1
TCH = 124
PCL = 19
Output Loss = 0.5
Input Loss = 0.5
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 13.0 Gold Sample Rx Level = 29
BER measurement level = -105
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 27
EPSK MCS = 9
[DCS 1]
Active = 1
TCH = 512
PCL = 0
Output Loss = 0.7
Input Loss = 0.7
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
BBB = 1
Gold Sample Average Power = 29.2 Gold Sample Rx Level = 29
BER measurement level = -104
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 27
EPSK MCS = 9
[DCS 2]
Active = 1
TCH = 700
PCL = 0
Output Loss = 0.7
Input Loss = 0.7
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 20.0 Gold Sample Rx Level = 29
BER measurement level = -104
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 27
EPSK MCS = 9
[DCS 3]
Active = 1
TCH = 885
PCL = 0
Output Loss = 0.7
Input Loss = 0.7
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 10.0 Gold Sample Rx Level = 29
BER measurement level = -104
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 25
EPSK MCS = 9
[DCS 4]
Active = 1
TCH = 512
PCL = 15
Output Loss = 0.7
Input Loss = 0.7
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 29.2 Gold Sample Rx Level = 29
BER measurement level = -104
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 27
EPSK MCS = 9
[DCS 5]
Active = 1
TCH = 700
PCL = 15
Output Loss = 0.7
Input Loss = 0.7
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 20.0 Gold Sample Rx Level = 29
BER measurement level = -104
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 27
EPSK MCS = 9
[DCS 6]
Active = 1
TCH = 885
PCL = 15
Output Loss = 0.7
Input Loss = 0.7
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1
Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 10.0 Gold Sample Rx Level = 29
BER measurement level = -104
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 25
EPSK MCS = 9
[PCS 1]
Active = 1
TCH = 512
PCL = 0
Output Loss = 0.7
Input Loss = 0.7
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 29 Gold Sample Rx Level = 29
BER measurement level = -104
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 27
EPSK MCS = 9
[PCS 2]
Active = 1
TCH = 660
PCL = 0
Output Loss = 0.7
Input Loss = 0.7
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 29.0 Gold Sample Rx Level = 29
BER measurement level = -104
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 27
EPSK MCS = 9
[PCS 3]
Active = 1
TCH = 810
PCL = 0
Output Loss = 0.7
Input Loss = 0.7
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 29.0 Gold Sample Rx Level = 29
BER measurement level = -104
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 27
EPSK MCS = 9
[GSM850 1]
Active = 1
TCH = 128
PCL = 5
Output Loss = 0.5
Input Loss = 0.5
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 29.0 Gold Sample Rx Level = 29
BER measurement level = -105
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 27
EPSK MCS = 9
[GSM850 2]
Active = 1
TCH = 190
PCL = 5
Output Loss = 0.5
Input Loss = 0.5
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 29.0 Gold Sample Rx Level = 29
BER measurement level = -105
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 27
EPSK MCS = 9
[GSM850 3]
Active = 1
TCH = 251
PCL = 5
Output Loss = 0.5
Input Loss = 0.5
Average Burst Power = 1
Peak Burst Power = 1
PVT Match = 0
Timing Error = 0
Phase Error Peak = 1
Phase Error RMS = 1
Frequency Error = 1
Spectrum Modulation = 1 Spectrum Switch = 0
Rx Quality = 0
RX Level = 0
RFER = 0
BBB = 1
Gold Sample Average Power = 29.0 Gold Sample Rx Level = 29
BER measurement level = -105
BS TCH level = -81
RX Level Max Limit = 32
RX Level Min Limit = 27
EPSK MCS = 9
CAL.INI文件
[META version]
META version= ver 5.3.6.0
[Crystal AFC control]
cap_id=32
[AFC control]
Initial value=4000
Slope=7
[GSM850 Sub band, RX loss]
Max ARFCN=140,150,160,170,180,190,200,210,220,230,240,251
RX loss=-0.750,-0.875,-0.750,-0.875,-0.750,-0.750,-0.875,-0.875,-0.875,-0.875,-0.625,-0.6250 [GSM900 Sub band, RX loss]
Max ARFCN=15,30,40,50,60,70,80,95,110,124,1000,1023
RX loss=-0.875,-0.875,-0.875,-0.875,-0.875,-0.750,-0.625,-0.500,-0.375,-0.375,-0.750,-0.7500 [DCS1800 Sub band, RX loss]
Max ARFCN=550,580,610,640,670,700,730,760,790,820,850,885
RX loss=-0.125,-0.125,0.125,0.000,0.000,0.000,-0.125,-0.250,-0.125,-0.250,0.000,0.1250 [PCS1900 Sub band, RX loss]
Max ARFCN=540,565,590,615,640,665,690,715,740,765,790,810
RX loss=1.500,1.250,1.000,0.875,1.000,1.000,1.250,1.500,1.625,1.750,1.875,2.0000
[BB TX Parameters]
BB TX common mode voltage=-1
BB TX gain=-1
BB TX calrcsel=-2
APC bat low voltage=3.5
APC bat high voltage=4
APC bat low temperature=0
APC bat high temperature=50
Trim I=-2
Trim Q=1
Offset I=1
Offset Q=6
Calibrated flag=1
[GSM900 level, ramp]
APC dc offset=125
Low APC dc offset=0
APC lowest power=5
TX power level=57,65,74,88,102,123,147,179,216,266,320,395,491,569,690,690
profile 0 ramp up=0,0,0,0,0,0,0,8,25,65,145,219,255,255,255,255
profile 0 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 1 ramp up=0,0,0,0,0,0,0,8,25,65,145,219,255,255,255,255
profile 1 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 2 ramp up=0,0,0,0,0,0,0,8,25,65,145,219,255,255,255,255
profile 2 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 3 ramp up=0,0,0,0,0,0,0,8,25,65,145,219,255,255,255,255
profile 3 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 4 ramp up=0,0,0,0,0,0,0,8,25,65,145,219,255,255,255,255
profile 4 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 5 ramp up=0,0,0,0,0,0,0,8,32,80,145,215,255,255,255,255
profile 5 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 6 ramp up=0,0,0,0,0,0,0,8,25,65,145,219,255,255,255,255
profile 6 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 7 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 7 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 8 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 8 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 9 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 9 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 10 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 10 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 11 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 11 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 12 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 12 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 13 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 13 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 14 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 14 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 15 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 15 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
Subband max arfcn=40,82,124,1000,1023,-1,0,0,0,0,0
Subband mid level=11,11,11,11,11,11,11,11,11,11,11
Subband high weight=0.970,1.000,1.030,0.950,0.970,1.000,1.000,1.000,1.000,1.000,1.0000
当发现PCL5功率等级的个别信道偏高或偏低时，将针对相对应的信道系数改高或低；如发现124信道功率偏低，可以将上面的1.030改为1.05或更大一点。

Subband low weight=0.990,1.000,1.020,0.990,0.990,1.000,1.000,1.000,1.000,1.000,1.0000
当发现PCL19功率等级的个别信道偏高或偏低时，将针对相对应的信道系数改高或低；如发现124信道功率偏低，可以将上面的1.020改大一点，如1.05等等。

Battery compensate, low voltage, low temperature=1
Battery compensate, low voltage, mid temperature=1
Battery compensate, low voltage, high temperature=1
Battery compensate, mid voltage, low temperature=1
Battery compensate, mid voltage, mid temperature=1
Battery compensate, mid voltage, high temperature=1
Battery compensate, high voltage, low temperature=1
Battery compensate, high voltage, mid temperature=1
Battery compensate, high voltage, high temperature=1
TX AFC DAC offset=0
[DCS1800 level, ramp]
APC dc offset=125
Low APC dc offset=0
APC lowest power=0
TX power level=47,54,62,73,87,105,128,156,186,227,280,343,415,515,602,710
profile 0 ramp up=0,0,0,0,0,1,4,8,30,65,145,219,255,255,255,255
profile 0 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 1 ramp up=0,0,0,0,0,1,4,8,30,65,145,219,255,255,255,255
profile 1 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 2 ramp up=0,0,0,0,0,1,4,8,30,65,145,219,255,255,255,255
profile 2 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 3 ramp up=0,0,0,0,0,1,4,8,30,65,145,219,255,255,255,255
profile 3 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 4 ramp up=0,0,0,0,0,1,4,8,30,65,145,219,255,255,255,255
profile 4 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 5 ramp up=0,0,0,0,0,1,4,8,30,65,145,219,255,255,255,255
profile 5 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 6 ramp up=0,0,0,0,0,1,4,8,30,65,145,219,255,255,255,255
profile 6 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 7 ramp up=0,0,0,0,0,0,1,4,8,30,65,145,219,255,255,255
profile 7 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 8 ramp up=0,0,0,0,0,0,1,4,8,30,65,145,219,255,255,255
profile 8 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 9 ramp up=0,0,0,0,0,0,1,4,8,30,65,145,219,255,255,255
profile 9 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 10 ramp up=0,0,0,0,0,0,1,4,8,30,65,145,219,255,255,255
profile 10 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 11 ramp up=0,0,0,0,0,0,1,4,8,30,65,145,219,255,255,255
profile 11 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 12 ramp up=0,0,0,0,0,0,1,4,8,30,65,145,219,255,255,255
profile 12 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 13 ramp up=0,0,0,0,0,0,1,4,8,30,65,145,219,255,255,255
profile 13 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 14 ramp up=0,0,0,0,0,0,1,4,8,30,65,145,219,255,255,255
profile 14 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
profile 15 ramp up=0,0,0,0,0,0,1,4,8,30,65,145,219,255,255,255
profile 15 ramp down=239,197,138,78,32,10,0,0,0,0,0,0,0,0,0,0
Subband max arfcn=520,560,600,630,660,680,720,730,750,800,885
Subband mid level=9,9,9,9,9,9,9,9,9,9,9
Subband high weight=1.000,1.000,1.000,1.000,1.000,1.000,1.000,1.000,1.000,1.000,1.0100
Subband low weight=1.020,1.010,1.000,1.000,1.000,1.000,1.000,1.000,1.000,1.000,0.9900 修改DCS部分信道平坦度，找到对应信道的系数，修改同上。

Battery compensate, low voltage, low temperature=1
Battery compensate, low voltage, mid temperature=1
Battery compensate, low voltage, high temperature=1
Battery compensate, mid voltage, low temperature=1
Battery compensate, mid voltage, mid temperature=1
Battery compensate, mid voltage, high temperature=1
Battery compensate, high voltage, low temperature=1
Battery compensate, high voltage, mid temperature=1
Battery compensate, high voltage, high temperature=1
TX AFC DAC offset=0
[PCS1900 level, ramp]
APC dc offset=125
Low APC dc offset=0
APC lowest power=5
TX power level=44,51,59,69,81,96,115,139,166,202,250,307,376,441,536,536
profile 0 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 0 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 1 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 1 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 2 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 2 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 3 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 3 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 4 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 4 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 5 ramp up=0,0,0,0,0,0,0,0,8,32,80,145,215,255,255,255
profile 5 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 6 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 6 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 7 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 7 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 8 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 8 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 9 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 9 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 10 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 10 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 11 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 11 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0
profile 12 ramp up=0,0,0,0,0,0,0,0,8,25,65,145,219,255,255,255
profile 12 ramp down=255,239,197,138,78,32,10,0,0,0,0,0,0,0,0,0。