Part Data Creation Procedure

Part Data Creation Procedure

Contents

1.Outline (3)

2.Coplanarity Check Part Data Setting Items (3)

3.Setting Procedure (5)

3.1.Part Number (5)

3.2.Part Type (5)

3.3.Part Character (6)

3.4.Terminal Locate (6)

3.5.Coplanarity (6)

3.6.Inclination (6)

3.7.Dark Level (6)

ser power (7)

3.9.AGC range (7)

3.10.Overall size X, Y (7)

3.11.Terminal Outside Size X, Y (7)

3.12.Terminal Pitch X,Y (10)

3.13.Terminal count X, Y (11)

3.14.Terminal Size X,Y (12)

3.15.Lead-Sampling Position (13)

3.16.Number of Missing Terminals (13)

3.17.X, Y (Missing Terminal Coordinates) (13)

3.18.Number of Missing Terminal Areas (14)

3.19.X1, Y1, X2, Y2 (Missing Terminal Area) (14)

3.20.Number of Thick Leads (15)

3.21.X, Y1, Y2 (Thick Lead Area) (16)

1. Outline

This document explains the coplanarity check part data settings in Coplanarity Editor.

2.

Coplanarity Check Part Data Setting Items

The coplanarity check part data setting items are listed below.

Classifica tion

Item

Setting range Description

Unit Default Setting method Part No.

1 to 500Specifies the part number.-- 3.1Part type 1,2,3,4,5,

6Specifies the part type.

(Terminal shape/arrangement)-- 3.2Part

parameter s

Part character 1,2,3,4,5,

6

Specifies the terminal characteristics.

-- 3.3Terminal locate

0 ~Specifies the terminal XY direction offset tolerance.

μm - 3.4Coplanarity 0 ~Specifies the terminal height variance tolerance.

μm - 3.5Threshold value

Inclination

0 ~Specifies the tolerance for inclination from the terminal reference plane.1/100deg - 3.6Dark level

1 to 4096Specifies the dark level (Detection level for light reflected off the terminals).

-30 3.7Laser power 1 to 7Specifies the laser output.-5 3.8Sensor setting

AGC range

1 to 5Specifies the AGC range.

-1 3.9Overall size X, Y

1 ~Specifies the part outline size.μm 50000 3.10Terminal Outside Size X, Y

1 ~Specifies the outline size for the terminals only.

μm 35500 3.11Terminal pitch X, Y 1 ~Specifies the spacing between adjacent terminals.

μm 5000 3.12Terminal count X, Y

1 ~Specifies the terminal count.μm 8 3.13Terminal size X, Y

1 ~

Specifies the terminal size.In the case of lead terminals, X

always represents the terminal width and Y the terminal length regardless of the part orientation.

μm

500

3.14

Part size

Lead-sampling position

0 ~Specifies the position at which the lead height is measured.

μm 200 3.15Number of missing terminals

0 ~Specifies the missing terminal count.-0 3.16X, Y

1 ~Specifies the missing terminal position.

-(No lines)

3.17Number of missing terminal areas 0 ~Specifies the number of missing terminal areas.

-0 3.18Missing terminal

X1, Y1, X2, Y2

1 ~Specifies the missing terminal area range.

-(No lines)

3.19Number of thick leads 0 ~Specifies the wide lead count.-0 3.20Thick terminal

X, Y1, Y2 1 ~

Specifies the wide lead range.

-

(No lines)

3.21

Note:

The default values are set automatically by Coplanarity Editor when part data is set for the