水性油墨疏水剂ADS3W6001
NUW3390系列超级白色预催化漆 Zenith透明防水剂说明书
The data on this sheet represent typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Axalta assumes no obligation or liability for use of this information . UNLESS AXALTA AGREES OTHERWISE IN WRITING, AXALTA MAKES NO WARRANTIES, EXPRESS ORIMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. AXALTA WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in thisproduct is the replacement of the defective product, or a refund of its purchase price, at our option. The information in this sheet, as well as the products referenced herein, shall beGENERAL INFORMATIONAxalta ’s SUPERLAC PLUS™ Pre -catalyzed White Lacquers are a line of highly durable pre-catalyzed lacquers that offer excellent build and durability approaching that of two-component acid cured coatings in a HAPs Free formulation. The high build, UV protection, chemical and mar resistance that this product provides makes in an excellent choice for cabinet and furniture applications. This product can be tinted to achieve unlimited colour options.1. PRODUCTS• NUW3390-90C NUW3390-35C• NUW3390-25C NUW3390-10C2. MIXING RATIO• All products should be stirred well before use and, forbest results, continuously agitated while in use.3. SHELF LIFE @ 77°F (25°C)• 6 months from manufacture date4. CLEAN UP• All products should be stirred well before use and, for bestresults, continuously agitated while in use.5. ADDITIVES• In the event of blushing or blistering, add Axalta 390-9303-00 Lacquer Retarder to extend dry time. See Additional Notes portion of this document for details.6. SURFACE PREPARATION• Surface must be clean and dust free with a moisturecontent of 6-8% prior to finishing. Remove all dust, dirt, wax and wood marks. Proper sanding and preparation of the wood is critical to achieving consistent results.• On new wood, finish sand surface with 150-180 grit sandpaper• On previously finished wood, remove all old paint or varnish and follow new wood procedure.7. COMPANION PRODUCTS• 383-1902-00 & 383-9905-00 SUPERLAC ™ Basecoats8. TECH NOTES• If reduction is necessary, use Axalta 390-7001-00 LacquerThinner. See Additional Notes portion of this document for details.9. SUBSTRATES• Commonly used furniture and cabinetry woods • MDF/HDFNOTE: Not to be used on exterior applications10. APPLICATION• See application notes for additional details.11. FLASH / DRY TIMESAIR DRY @ 77°F (25°C)12. FORCE DRYFlash 10 Minutes Bake 5 Minutes @ 125°F Cool Down 10 Minutes ambient StackAfter cool down13. GUN SET UPGravity Feed 1.6 mm - 1.8 mm Siphon Feed 1.8 mm – 2.0 mm Airless10 – 15 thousandths Air-Assisted Airless11 – 15 thousandthsAIR PRESSURESGravity Feed 30-35 psi (2.0-2.4 bar) Siphon Feed 35-40 psi (2.4-2.8 bar) Air-Assisted Airless10-20 psi (0.7-1.4 bar)See spray gun manufacturer data for more information14. PHYSICAL DATAViscosity24±2” #2 Zahn at 25˚C(~77˚F)Weight Solids % 41±2% Volume Solids % 27±2%Actual VOC4.34lbs/gal of Product VOC Ratio (lb.voc/lb.solids) 1.17lb VOC/lb solidRegulatory VOC(less water and exempt solvents)576g/l Weight Per Gallon 8.68-8.875lbs/gal Flash Point-4°C (~25°F) Tag Open Cup(TOC) Theoretical Coverage 454 ft/gal @ 1 mil dry VHAP (lb.HAP/lb.solids) 0.03lb VHAP/lb solidCoating CategoryWhiteDry to touch20 - 25 Minutes Flash between coats 35 - 45 Minutes To Stack12 - 24 HoursThe data on this sheet represent typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Axalta assumes no obligation or liability for use of this information . UNLESS AXALTA AGREES OTHERWISE IN WRITING, AXALTA MAKES NO WARRANTIES, EXPRESS ORIMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. AXALTA WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in thisproduct is the replacement of the defective product, or a refund of its purchase price, at our option. The information in this sheet, as well as the products referenced herein, shall beApplication Notes:All products should be stirred well before use and, for best results, continuously agitated while in use. Do not mix with other finishing systems or deviate from these finishing recommendations. Axalta will not be held liable for finish failures resulting from the mixing of products or deviations from finishing recommendations. Sandingshould be completed immediately prior to the application of any additional coats.1) Seal: NUW3390 Series lacquers are self-sealing. If a basecoat is desired, use 383-1902-00 or other approved basecoat. Refer to Technical Data Sheet for detailed use instructions. Sand with 240–320 grit stearated, silicon carbide sandpaper.2) Finish: Choose the appropriate sheen from the series, and agitate well before applying. Verify the surface is clean and dust free, and apply an even coat at 3–4 wet mils using conventional, airless, air-assisted or HVLP spray equipment.If additional coats are required, wait a minimum of 30 minutes between applications. Sand with 280–320 grit stearated, silicon carbide sandpaper before recoating. If reduction is necessary, use Axalta 390-7001-00 Lacquer Thinner. See Additional Notes portion of thisdocument for additional details. In the event of blushing or blistering, add Axalta 390-9303-00 Lacquer Retarder to extend dry time. See Additional Notes portion of this document for additional details.IMPORTANT NOTE: System’s total dry film build should not exceed 4 mils . A higher build may result in a film breakdown or reduction in performance. Clean Up:Use lacquer thinner to clean equipment. Refer to yourlocal regulations for compliance requirements for cleaning thinners, or use recommended Axalta Lacquer Thinner. Dispose of dirty solvent and cleaning rags in a safe and compliant manner. Solvent or lacquer soaked rags should be stored in water-filled, closed containers prior to disposal.Precautions:These products are recommended for professionalapplication and are designed for interior use only. Always pre-test the system on your substrate and under your line conditions to verify suitability to the application and toavoid potential need for costly refinishing. Axalta Industrial Wood Coatings are designed to protect and enhance the natural beauty of wood, but cannot eliminate natural discoloration or deterioration of wood as it ages.Additional notes:Do not mix with other finishing systems or deviate from these finishing recommendations. Axalta will not be heldliable for finish failures resulting from the mixing of products or deviations from finishing recommendations.Catalyzation: n/a Pot-Life: n/a Reduction: Max. 20% by volume 390-7001* Retarder: Max. 5% by volume 390-9303*As allowable within regulatory compliance requirementsStorage:Store in a cool, dry place. DO NOT FREEZE! Product should be stored in temperatures between 50°-110°F. Close all containers after use. Do not store near heat or sparks.Spills should be cleaned up with non-sparking tools. See the product SDS for complete safety information.Warning:Always pre-test the system on your substrate and underyour line conditions to verify suitability to the application and avoid potential need for costly refinishing. All dry times listed are as tested under ideal indoor environmental conditions of 78°F (26°C) with relative humidity notexceeding 50%. These products are recommended for use under temperature conditions of 60-100°F (16-38°C) and when relative humidity is below 50% during application and drying time. Low temperatures, poor air circulation or high humidity will extend dry times. Axalta strongly recommends against use of these products iftemperatures of air, material, or surface to be coated are below 60°F (16°C) or below the dew point.Abnormal conditions of temperature or humidity may adversely affect product performance. Please contact your authorized Axalta Industrial Wood Coatings distributor for additional product use recommendations and finishing guidance.。
水性油墨 MSDS
进入眼睛时 用洁净清水清洗10分钟
接触皮肤时 用肥皂或温和清洁剂及水清洗
吸入时 脱离接触区域，吸入新鲜空气
食入时 呕吐，肚子痛，如少量的食入，喝一些水或生奶，如大量的需立即送往医院检查
（5）发生火灾时的应对方法
灭火剂 干粉，粉沫，二氧化碳，喷雾灭火器等
灭火方法 喷洒
（6）发生泄露时的应对方法
比重1：1.3
（10）安全性反应性
稳定性 稳定（室温）
保管要求 远离氧化剂、酸性物料
有害分解物 周围环境温度不会分解
聚合反应 在有效期限内不会发生
（11）有关毒性方面的信息
毒害信息 急性经过毒性实验（一次最大限度试验）雌性、雄性小鼠LD50均大于草5000mg/kgBW为实际低毒。急性吸入毒性实验（一次最大限度试验）：雌性、雄性小鼠LC50均大于1000mg/m3,为实际低毒
（14）有关运输方面的信息
运输信息 运输部门有责任按所有的法律、法规和规定要求来运输货物
（15）法律规章制度的现况
国家政府规定 中华人民共和国固体废弃物污染环境防治法
当地政府规定 地方政府水污染排放标准
（16）其他参考事项
其他资料 可通过销售部门和技术服务部门获得其它信息和手册
（8）防止泄露及个人防护
管理方法尽量存放在室内，使用后确认封口密封，防止水墨泄漏
对呼吸道的防护 高浓度区域使用防护口罩
对眼睛防护 请使用保护眼镜
对手的防护 请使用耐化学性的防护套
对身体防护 请使用非渗透性的安全服装及安全鞋
卫生注意事项 作业后用水清洗
（9）物理化学特性
外观 油状液体
气味 略带刺激性气味
物料安全规格资料MSDS
水性油墨荷叶疏水剂ADS3W6001
水性油墨荷叶疏水剂ADS3W6001
一、水性油墨荷叶疏水剂技术参数：
1、外观：灰白色均质半透明液体；
2、固含量：30%；
3、PH值：7-9；
4、粒径：约0.065微米；
5、熔点：约56-62℃；
6、离子型：水性非离子型。
二、水性油墨荷叶疏水剂性能特点：
水性油墨荷叶疏水剂为水溶性环保非离子型，其抗酸、抗碱、耐硬水、水溶性强、乳液稳定，任意比例水稀释不分层、不破乳、不结块、保质期长、固含量高、分散性好。
三、水性油墨荷叶疏水剂适用范围：
本品应用于水性油墨体系中，可起到水墨表面的疏水（即荷叶疏水）性能及抗粘性能，使涂膜更加爽滑。
四、水性油墨荷叶疏水剂使用方法:建议本品以3%-5%的添加量添加于油墨体系中,具体情况可根据贵司产品体系酌情调兑。
五、水性油墨荷叶疏水剂储存方式：
在10-25℃的条件下，避光、密闭贮存可达6个月以上。
六、水性油墨荷叶疏水剂包装规格：50KG/桶。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
水性油墨疏水剂ADS3W6001
一、水性油墨疏水剂技术参数：
1、外观：灰白色均质半透明液体；
2、固含量：30%；
3、PH值：7-9；
4、粒径：约0.065微米；
5、熔点：约56-62℃；
6、离子型：水性非离子型。
二、水性油墨疏水剂性能特点：
水性油墨疏水剂为水溶性环保非离子型，其抗酸、抗碱、耐硬水、水溶性强、乳液稳定，任意比例水稀释不分层、不破乳、不结块、保质期长、固含量高、分散性好。
三、水性油墨疏水剂适用范围：
本品应用于水性油墨体系中，可起到水墨表面的疏水（即荷叶疏水）性能及抗粘性能，使涂膜更加爽滑。
四、水性油墨疏水剂使用方法:建议本品以3%-5%的添加量添加于油墨体系中,具体情况可根据贵司产品体系酌情调兑。
五、水性油墨疏水剂储存方式：
在10-25℃的条件下，避光、密闭贮存可达6个月以上。
六、水性油墨疏水剂包装规格：50KG/桶
水性油墨是由连结料、颜料、助剂等物质组成的均匀浆状物质。
连结料提供油墨必要的转移性能，颜料赋予油墨以色彩。
水性油墨的连结料主要分为两种类型：水稀释型和水分散型。
前者可以使用的树脂类型有很多种，比如顺丁烯二酸树脂、紫胶、马来酸树脂改性虫胶、乌拉坦、水溶性丙烯酸树脂和水性氨基树脂等。
水分散型的连结料是在水中通过乳化的单体聚合所得，它是两相体系，其中油相以颗粒状在水相中分散，虽不能够被水溶解，但能够被水稀释，所以也可以认为是水包油乳液型。