GC1012B中文资料

Texas Instruments Incorporated
-i-
This document contains information which may be changed at any time without notice
元器件交易网
GC1012B 3.3V DIGITAL TUNER CHIP SLWS138B
0.1.2
Control Interface
The control interface has been enhanced to use either the R/W and CS strobes of the original GC1012A, or to use the RE, WE and CE strobes used by most memory interfaces. If the RE pin is grounded, then the interface behaves in the R/W and CS mode, where the WE pin becomes the R/W pin and the CE pin becomes the CS pin. The RE pin on the GC1012B chip is a ground pin (pin 103) on the GC1012A chip, so that a GC1012B chip soldered into a GC1012A socket will automatically operate in the GC1012A R/W and CS mode. See Section 1.3 for details.
TABLE OF CONTENTS
1.0
1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11
FUNCTIONAL DESCRIPTION .................................................................................................... 1
0.1.1
Clock Loss Detect and Power Down Modes
The GC1012A chip used a slow internal clock to power down the chip or to put it into a low power mode if the clock is stopped. The slow clock has been removed in the GC1012B and replaced with a mode that will put the chip in a fully static mode if the clock has stopped. The fully static mode powers down the chip and reduces the power consumption down to a few microwatts until the clock resumes. The user can also forcsired. Two control bits (address 7 bit 5 and address 9 bit 7) are used to control the clock loss detect and power down modes. One control bit turns off the clock loss detect circuit, the other forces the power down mode. Both bits are cleared at power up to keep GC1012A compatibility. See Section 1.9 for details.
元器件交易网
GC1012B 3.3V DIGITAL TUNER CHIP SLWS138B
REVISION HISTORY
This datasheet is revised from the GC1012A datasheet to reflect the changes in the GC1012B replacement.
元器件交易网
SLWS138B
GC1012B
3.3V DIGITAL TUNER CHIP
DATASHEET
October 2002
This datasheet contains information which may be changed at any time without notice.
KEY FEATURES ....................................................................................................................................1 BLOCK DIAGRAM .................................................................................................................................2 CONTROL INTERFACE ........................................................................................................................2 DIGITAL OSCILLATOR..........................................................................................................................3 MIXER ....................................................................................................................................................4 PROGRAMMABLE LOW PASS FILTER................................................................................................4 GAIN.......................................................................................................................................................5 OUTPUT FORMATTING ........................................................................................................................6 POWER DOWN AND KEEPALIVE MODES ..........................................................................................6 THE ONE SHOT PULSE GENERATOR ................................................................................................6 DIAGNOSTICS.......................................................................................................................................7
Revision
1.0 1.1
Date
3 May 2002 9 October 2002
Description
First GC1012A datasheet. Major changes in specifications to reflect 3.3volt operation. Corrected checksum table, page 7
2.0 3.0
3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9
PIN DESCRIPTIONS ................................................................................................................... 8 CONTROL REGISTERS............................................................................................................10
0.1
GC1012B TO GC1012A COMPARISON
The GC1012B is designed to be a functional and footprint compatible replacement for the GC1012A chip. The timing specifications for the GC1012B meet and exceed the timing specifications for the GC1012A. Electrically the GC1012B is a 3.3 volt only part, making it incompatible with the GC1012A’s 5 volt mode. The GC1012B is fully compatible with the GC1012A’s 3.3 volt mode, but at a lower power consumption. See Section 4 for timing and electrical specifications. NOTE: The GC1012B inputs are NOT 5 volt tolerant; chip damage may occur if the input voltages exceed Vcc + 0.5V (3.8 volts). Designs using the GC1012A at 5 volts will need to add a 3.3 volt supply and voltage level translators to use the GC1012B. The function of the GC1012B has been slightly enhanced, but any enhancements are “backward” compatible with the GC1012A so that a GC1012A user will not need to change any software or processing algorithms to use the GC1012B chip. The checksums for the diagnostics have changed and are shown on page 7. Highlights of the enhancements follow.