常用模具零件中英文对照表

常用模具零件中英文对照表
2005-12-19 14:51:17中国注塑网
一、入水：gate
进入位：gate location
水口形式：gate type
大水口：edge gate
细水口：pin-point gate
水口大小：gate size
转水口：switching runner/gate
唧嘴口径：sprue diameter
二、流道: runner
热流道：hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道：round(full/half runner
流道电脑分析：mold flow analysis
流道平衡:runner balance
热嘴：hot sprue
热流道板：hot manifold
发热管：cartridge heater
探针: thermocouples
插头：connector plug
插座：connector socket
密封/封料：seal
三、运水：water line
喉塞：line lpug
喉管：tube
塑胶管：plastic tube
快速接头：jiffy quick connector plug/socker
四、模具零件：mold components
三板模：3-plate mold
二板模：2-plate mold
边钉/导边：leader pin/guide pin
边司/导套：bushing/guide bushing
中托司：shoulder guide bushing
中托边：guide pin
顶针板：ejector retainner plate
托板：support plate
螺丝：screw
管钉：dowel pin
开模槽：ply bar scot
内模管位：core/cavity inter-lock
顶针：ejector pin
司筒：ejector sleeve
司筒针：ejector pin
推板：stripper plate
缩呵：movable core,return core core puller 扣机〔尼龙拉勾〕：nylon latch lock
斜顶：lifter
模胚〔架〕：mold base
上内模：cavity insert
下内模：core insert
行位〔滑块〕：slide
镶件：insert
压座/斜鸡：wedge
耐磨板/油板：wedge wear plate
压条：plate
撑头: support pillar
唧嘴：sprue bushing
挡板：stop plate
定位圈：locating ring
锁扣：latch
扣鸡：parting lock set
推杆：push bar
栓打螺丝：S.H.S.B
顶板：eracuretun
活动臂：lever arm
分流锥：spure sperader
水口司:bush
垃圾钉：stop pin
隔片：buffle
弹弓柱：spring rod
弹弓:die spring
中托司：ejector guide bush
中托边：ejector guide pin
镶针：pin
销子：dowel pin
波子弹弓：ball catch
喉塞:pipeplug
锁模块：lockplate
斜顶：anglefrompin
斜顶杆：angleejectorrod
尼龙拉勾：partinglocks
活动臂：leverarm
复位键、提前回杆：earlyreturnbar
气阀：valves
斜导边：anglepin
术语：terms
承压平面平衡：partingsurfacesupportbalance
模排气：partinglineventing
回针碰料位：returnpinandcavityinterference
模总高超出啤机规格：moldbaseshuthight
顶针碰运水：waterlineinterfereswithejectorpin
料位出上/下模：partfromcavith(core)side
模胚原身出料位：cavitydirectcutonA-plate,coredirectcutonB-plate.
不准用镶件：Donotuse(core/cavity)insert
用铍铜做镶件：useberylliumcopperinsert
初步〔正式〕模图设计：preliinary(final)molddesign
反呵：reversecore
弹弓压缩量：springcompressedlength
稳定性好：goodstability,stable
强度不够：insufficientrigidity
均匀冷却：evencooling
扣模：sticking
热膨胀：theroexpansion
公差：tolorance
铜公(电极〕：copperelectrode
塑件模具相关英文词汇
出处：FanE『翻译中国』(转载) FanE『翻译中国』2005-12-16 20:41:59
compre sion molding压缩成型
flash mold溢流式模具
plsitive mold挤压式模具
split mold分割式模具
cavity型控母模
core模心公模
taper锥拔
leather cloak仿皮革
shiver饰纹
flow mark流痕
welding mark溶合痕
post screw insert螺纹套筒埋值
self tapping screw自攻螺丝
striper plate脱料板
piston活塞
cylinder汽缸套
chip细碎物
handle mold手持式模具
encapsulation molding低压封装成型、射出成型用模具two plate两极式〔模具〕
well type蓄料井
insulated runner绝缘浇道方式
hot runner热浇道
runner plat浇道模块
valve gate阀门浇口
band heater环带状的电热器
spindle阀针
spear head刨尖头
slag well冷料井
cold slag冷料渣
air vent排气道
welding line熔合痕
eject pin顶出针
零件英语
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location 定位支承块 air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch 切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch 压筋冲子
reel-stretch punch 卷圆压平冲子
guide plate 定位板
sliding block 滑块
sliding dowel block 滑块固定块
active plate 活动板
lower sliding plate 下滑块板
upper holder block 上压块
upper mid plate 上中间板
spring box 弹簧箱
spring-box eject-rod 弹簧箱顶杆
spring-box eject-plate 弹簧箱顶板
bushing bolck 衬套
cover plate 盖板
guide pad 导料块
14. electrical discharge machining (EDM) 电火花加工
15. electrical insulating property 电绝缘性能
16. electrochemical die-sinking machine 电解型腔加工机，电解型腔加工机床
17. electrochemical machine (ECM) 电解加工机床，电化学加工机床
18. electrochemical machining (ECM) 电解加工，电化学加工
19. electro-discharge cutting 电火花加工，电火花切割
20. electro-discharge cutting machine 电火花切割机
21. electro-discharge machine tool 电火花加工机床
22. Electro-discharge Machine 电火花加工机床
23. electro-discharge machining 电火花加工
24. electro-discharge machining process 电火花加工工艺，电火花加工工序
25. epoxy resin 环氧树脂
9. guide bushing 导套
10. guide pillar 导柱，导杆，导柱
11. guide pin 导向销，导杆
12. guide pin cover 导柱盖
13. guide plate 导料板，导板
14. guide plate blanking die 导板式冲裁模，导板式落料模
15. guide post 导柱，导柱
16. guide stock plate 挡料板
4. injection mold 注射模，注塑模
5. injection molding 注射成型，注塑成型
6. injection-molding machine 注塑机，注射机，注塑成形机
7. injection plunger 注射柱塞
8. in-line reciprocating screw 联机往复螺杆，串联往复螺杆，直线排列往复螺杆
9. inner ram 内滑块
10. inserting molding 嵌件成形
11. integrated manufacturing 集成制造
12. internal stress 内应力
13. intermediate platen 中间板，隔板
塑料成型模具的主要设计要素
脱模距stripper distance
脱模斜度draft
投影面积projected area
最大开距maximum daylight;open daylight
闭合高度mould-shut height
抽芯距core-pulling distance
抽芯力core-pulling force
脱模力ejector force
开模力mould opening force
模内压力internal mould pressure;cavity pressure
成型压力moulding pressure
背压环back-up ring
1 bar = 14.5psi
高压接头bite type fitting
液压马达hydraulic motor
冷却水流量计waterflow regulator
打磨器材abrasive material
打磨砂轮grinding wheels
切割砂轮cutting wheels
码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具piping tools
高压力软管high pressure hose
风管,水软管air .water hose
高压油表pressure gauge
压力油喉hydraulic hoses
光塑检测photoelastic testing
吹塑模plastic blow mould
注塑模plastic injection mould
冲扎复合模blank & form compound die
精密冲模precision blanking die
熔料流动率MFR=melt flow rate
熔料流动指数MET=melt flow index
推板导柱guide pin for ejector plater
座板clamping plate
垫块space block(plate)
推板ejector block(plate)
afdek plate 档尘板
guide stripe 行位后板
cavity sub-insert 前模镶件
core sub-insert 后模镶件
sprue puller insert 扣针镶件
stage ejector 顶棍
spacer rock(risers) 间隔板
变形distortion
弯曲warp
拖花drag marks
火花纹EDM marks
困气venting
烧黑burns
外表缩水shrinkage
料位过薄/砸穿thin wall stock
走水不平行uneven fill pattern
夹水纹/流纹witness line;mismatch;stress marks 走水纹knit lines
走水不齐short shots
orifice 料口
nozzle seat 热嘴垫圈
nozzle plate 射嘴板
cross pin 十字头销
sled 射台
seal ring 封密圈
spacer rail 介子座
heater groove 发热管槽
heater cement 发热管的结合剂
soak 浸泡
seat 垫圈
ream 铰大圆孔直径
grind 磨床
drill 钻床
mill 铣床
caliper 卡尺
G-caliper 分厘卡
Depth Gauge 深厚计
hardness tester 硬度计
angle gauge 角规
marble table 云台石
projector 投影仪
height gauge 高度仪
microscope 显微镜
plug gauge 塞规
leveller 水平器
R gauge R 规
Inter caliper 内分厘卡
surface 平面仪
item number 细目编码
catalog number 材料分类编码undercut lip 倒扣口
hot tip = hot drop = nozzle 热嘴
blow-off strip 放气板
blow-off nozzle 吹风口
spiral hose 螺旋式的连接喉
rust solvent 除锈剂
shaft 曲轴
tensile strength 拉伸力
yield strength 屈服力
spark erosion 电火花蚀刻
etch(photo-etch) 电蚀
harden 淬硬
copper electrode 铜公
corrosion resistance 耐腐蚀
anneal 退火
heat treatment 淬火
FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域
reverse taper 倒啤把
clamp plate 码板
toggle clamp 快速夹
vacuum furnace 真空炉
cavity insert rounds 圆柱镶件
cavity insert b0locks 方柱镶件
tensile strength 抗张强度,抗拉强度Concept drawing 概念图
Assembly drawing 装配图
mismatch;witness line 夹纹
shut-off(n.) 枕位
venting valves 疏气阀
venting plug 疏气塞
valve casing 阀门罩
twist drill 旋钻
harden/nitride 碎硬
anneal 退火
temper 回火
stess crack 应力断裂
corrosion resistance 防腐,防锈
tensile strength 物】抗张强度,抗拉强度split mould (别离)组合式的模具
inclined plate 斜面
inclined bolt 斜栓
jaw (工具,机械等)夹住东西的局部,钳口step change of the P/L 分形面枕位的改变thin steel section 较薄的料位
clean-up 清理,去除,清扫
Mold Dating Insert 模具日志镶件
Hot Sprue Bushing 热浇口套
semi-automatic 半自动
quick disconnector 快速断开接头
full shot 足量注射
mismatch 夹痕;夹水纹
ejector mark 顶痕
screw boss 螺丝孔,螺丝基座
sink mark 缩坑
15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂
drag mark 拖痕
stress mark 应力痕
reinforcement rib 加强筋
slght stoning 轻度磨砂
soliid line 实线
dotted line 虚线
internal diameter 内径
external diameter 外径
nickel-plated 电镀的
handling hole;lifting hole 吊装孔
parallel 平行块
piston 活塞
plunger 柱塞
carrier 导轨
rest 支架
item number 工程编号
catalog item 商品目录编码
dimensional datum 尺寸基准
heat treatment certification 淬硬证明文件
back-up bushing 支撑导套
jacking screw 起重螺丝,千斤顶
tapped hole (带有螺旋角度的)螺丝孔
diagonal corner 成对角的角落
burn mark 烧痕
hot runner mainfold (热流道板)分流板
texuring 蚀纹
clamping screw (注塑机)码模螺丝
imperial 英制的
metric 公制的
puller bushing 水口套
puller bar 水口铁
drool bushing 防漏胶套筒
safety switch 限位制
water line connected internally or hard tubing 不可用胶喉连接运水lifter on square rod or locked from rotation 用方形柱或用管钉止转gate insert 入水镶件
gate shut-offs 流道开关配件
guided ejection 中托司
parting line shutoff 前后模接触面
waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱. BGV=Balanced Gate Value 平衡入水值
spacer 垫块
pocket 挖槽
rough 粗加工
finish 精加工
plunge rate 进刀率
retract rate 提刀速率
splindle rate 主轴转速
coolant 冷却液
SPLIT RING 开口环(钥匙圈)
侧向抽芯力side pulling-core force
convert.transfer 转图
guide pin 边针
Tee slot cutter T形SLOT CUTTER
zigzag 双向切削
constant overlap spiral 等距环切
parallel spiral 环绕切削
parallel spiral clean corners 环切并清角
morph spiral 依外形环绕
true spiral 螺旋切削
one way 单向
end mill 平铣刀
spher mill 球刀
bull mill 圆鼻刀
face mill 面铣刀
rad mill 圆角成型刀
chamfer mill 倒角刀
slot mill 槽刀
taper mill 推拔铣刀
dove mill 鸠尾铣刀
lot mill 棒状
drill 钻孔
reamer 纹刀
bore bar 搪刀
tap RH 右牙刀
Tap LH 左牙刀
ctr Drill 中心钻
spot drill 点钻
cntr bore 沉头孔刀
c. sink 鱼眼孔钻
loft surface 举升曲面
coons surface 昆氏曲面
ruled surface 直纹曲面
revolved surface 旋转曲面
swept surface 扫描曲面
draft surface 牵引曲面
grinding wheel 磨砂使用的轮子
quench steel 将...淬火,使冷却
stress relieving 应力消除
molten 熔热的
oxide film 氧化层
guide pin and sleeve, locating ring ,导边,司筒,定位圈
ejector ,ejector balde, ejector sleeve,顶针,扁顶针,顶针司筒, lifters, wear plate,horn pin,斜坊,磨损板,气顶针,
O ring, water baffle, water pipe plug,O形圈,隔片,运水管道塞, water line connector,wear plate ,运水管道转接头,耐磨板
air cylinder,hydraulic cylinder,氯压缸,液压缸
micro switch,oil nipple, spring,开关装置,油枪接头,弹弓
sprue bushing,early return system,浇口套,早期回撞装置, accelerated ejectors, slied holder,加速顶针,注塑周期计数器, cycle counter,date stamper，滑块固定板,生产日期铭牌,
hot runner system ，热流道系统
chemical composition 化学成份
thermal conductiivity 导热性能
thermal diffusivity 热扩散性能
dimensonal stablity 尺寸稳定性能
cooling effiency 冷却效率
easiler ejection 易于脱模
alloy insert 合金镶件
(cooling) duct 输送管;导管
maintenance cost 维护费用
ultrasonic testing 超声波检测
crack 断裂
direct gate 直接浇口
ring gate 环形浇口
disk gate;disphragm gate 盘形浇口
spoke gate;spider gate 轮辐浇口
pin-point gate 点浇口
edge gate 侧浇口
submarine gate;tunnel gate 潜伏浇口
fan gate 扇形浇口
tab gate 护耳浇口
runner plate 流道板(或冷或热)
secondary nozzle 二级喷嘴
torpedo;torpedo body assembly 鱼雷形组合体
catridge heater 管式加热器
heat pipe 热管
valve gate 阀式浇口
force plunger;pot plunger 柱塞
flash groove;spew groove 溢料槽
impression;cavity block;cavity plate 凹模
punch;force 凸模
movable insert;loose detail 活动镶件
cavity splits;core splits(凹模拼块) (型芯拼块) 拼块
side core 侧型芯
thread plug;threaded core 螺纹型芯
thread ring;threaded cavity 螺纹型环
cutting wheel 切割砂轮
grinding wheel 打磨砂轮
abrasive material 打磨器材
mould clamps;lifting clamp 砂模夹(注塑机使用)
air (water) hose 风管,水轮管
pressure gauge 高压油表
hydraulic hose 压力油喉
plastic blow mould 吹塑模
plastic injection mould 注塑模
blandk&form compound die 冲扎复合模
precisiion blanking die 精密冲模
MFR=melt flow rate 熔料流动率
MFT=melt flow index 熔料流动指数
handling hole 拉铃孔
stop plate 限位块
linder bush 衬套
spacer block(plate) 垫块,方铁
back-up ring 背位环
standoff 限位块
American Safety Hoist Rings. 英制平安吊装环
Mechanical Properties 机械性能
Tensile Strength(MPa) 抗拉强度
elongation 延伸率
hardness(Brinell) 硬度
shear stength(MPa) 剪切力
impact strength 冲韧性
Physical Properties 物理性能
solidification shrinkage 凝固收缩率
freezing range 凝固与熔范围
thermal expansion 热膨胀系数
specific heat 比热
thermal conductivity 热导率
electrical conductivity 电导率
micro-structure 金相分析
hot work tool steel 热作钢
circular motion 环形运动
variable 变数,参数
graphics window 图形窗口
45 degree entry and a zero degree exit. 进刀口45度,退刀口0度runner stripper plate 脱料板
stripper plate 活动板
spacer rock(risers) 间隔板
stage ejector 顶棍
sprue puller insert 扣针导套
guide strip 行位后板
afdek plate 挡尘板
side gate 大水口
pinpoint gate 细水口
SHCS 杯头螺丝
FHCS 平头螺丝
set screw 无头螺丝
ball catch 波子螺丝
wedge 行位较杯
gib 线条,(撑鸡的导轨)
latch 拉杆
clamp 码仔
spring guide pin 弹弓导柱
steel pad disc 橙仔方
ejector cam insert 斜顶块
(screw) nut 螺母
taper 嗲把/ 斜度
taper interlock 嗲把锁
texture 花纹
toggle-lok 回撞装置
top clamping plate 顶码板
unified national coarse (UNC) 美制螺丝(粗牙) unified national fine (UNF) 美制螺丝(幼牙) set screw 喷头螺丝
side gate 大水口
slide retainer 行位管位
water junction 喉咀
spacer block 登仔
jiffy-matic socket 喉咀套
jiffy-tite plug 喉咀公
spring plunger 弹弓座
sprue puller 勾针/勾粒
spring washer 弹簧塑圈
stepped ejector pin 有托顶针
strippers plate 推板/细水口板
submarine gate 潜水口
support pin 拉杆
support plate 暗板
surface finish 光洁度
alignment strip 斜锁
angle pin 斜针
fan gate 扇形入水
fillet 圆口
ball catch 弹弓波子
blade ejector 扁顶
bottom clamping plate 底码板
free length 自然长度
bridge piece 水口铁
helix spindle 锅杆
hose clip 水喉箍
bubbler 隔气运水
jiggle 斜顶
jiggle witness line 斜顶片位置
center distance (CRS) 山打距离(中心线距离)
clamp 码仔
contour 外形
leader pin 导针
location ring(flange) 法兰
counterbore 拔头,介子托
mock-up;prototype 手办
die cast 合金压铸
national pipe thread(NPT) 美制喉牙
overflow 垃圾位
ejection sleeve 司筒,顶套
epoxy 胶样
pin point gate 细水口
pressure plug 喉塞
pressure spring 压力弹簧
parting line flash 披锋
burned 烧黑
underfilled 缺料
insert mismatch 镶件夹口
ejector pins not flush 顶针有上下
ejector pins skid 顶针滑动
insert flash 镶件披锋
pressure transducer 压力探测头
hydraulic schematic 油积筒油路接驳图
jiffy connector recessed 安装喉嘴后不可突出模胚
knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位开关
stop block 限位块
safety strap 平安带
drool bushing 防漏胶套筒
insert mismatch 镶件夹口
EDM visible 明显火花纹
lifter scrapes 斜顶拖花
short shots 走水不齐
wall stock 料位厚薄
knit lines 走水纹
stress marks 夹水纹
uneven fill pattern 走水不平行
drag marks 拖花
sprue pretrusion 唧嘴突出高度
sprue orifice and radil size 唧嘴R尺寸sprue bushing-keyed 唧嘴有管钉English Chinese
program name 产口名称
part name 零件名称
tool name 模具名称
tool source 模具来源
tool steel 模具钢材
resin 塑料
program number 产品编号
part number 零件编号
tool number 模具编号
customer 客户名称
No of cavities 内模编号
machine size 啤机吨数
drum miller 鼓形铣床
duplex horizontal miller 复式卧铣床face miller 端面铣床
grinding miller 研磨机
plain miller 平面铣床
planer-type miller 刨式铣床
rack miller 齿条铣床
slab miller 大型平面铣床
slot miller 键槽铣刀
spline miller 花键铣刀
thread miller 螺纹铣刀
vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀
plastic mould steel 塑料模钢
cold work steel 冷作钢
hot work steel 热作钢
high speed steel 高速钢
electric magnetic clutch 电磁离合器pad printer 移印机
screen printer 丝印机
hot stamper 烫印机
solid carbide slitting saw 钻石钢锯片convex cutter 凸锣刀片
concave cutter 凹锣刀片
side&face cutters,staggered teeth 正侧双用镶钻石钢锣刀end-mill 锣刀
semi-rod 半圆刀
split double end 双头刀
single end 单头刀
2-flute 两辨
3-flute 三辨
4-flute 四辨
reamer 直拈
centre drill 中心钻
solid carbide drill 钻咀
zinc ingot 锌锭
aluminium ignot 铝锭
tin ignot 锡锭
heater cement 发热管的结合剂
heater groove 发热管槽
spacer rail 介子座
cross pin 十字头销
nozzle plate 射嘴板
nozzle seat 热嘴
addendum 齿冠
dedendum 齿根
air compressor 空气压缩机
air exhauster 抽气机
air intake 进气口
air seal 空气隔离层。