ASTM_A193(2005)高温用合金钢和不锈钢螺栓材料

合集下载

A193A193M-05高温用合金钢和不锈钢螺栓材料

本标准已经美国国防部认可采用。
1. 适用范围
1.1 本标准适用于高温压力容器、阀门、法兰及管配件用合金钢和不锈钢螺栓材料。本标准中所用术语“螺栓材料”包括棒钢、螺栓、螺钉、螺柱、双头螺栓和线才材料。棒钢和线材料应是热加工的。材料可进一步以无心磨削或冷拔。奥氏体不锈钢可以经固溶处理加退火，或退火加应变硬化。当订购变硬化奥氏体钢时，买方应特别注意保证完全理解附录 X1。
6.3 所有奥氏体不锈钢应经碳化物固溶热处理（对于每个类别的特殊要求见 6.3.1 和 6.3.4）。1，1B,1C（只有 B8R 和 B8S 级），2，2B 和 2C 类可适用于棒材，丝材和精制紧固件。 1A 类（所有级别）和 1C 类（只有 B8RA 和 B8SA 级）可适用于精制紧固件。1D 类只适用于直接从 1D 类的棒材或丝材机加工，未经过任何随后热或冷加工的棒材，丝材和精制紧固件。
3.2.1 热处理状态（对铁素体钢为正火加回火，或淬火加回火；对奥氏不锈钢为碳化物固溶处理（I 类钢）、轧后碳化物固溶处理（2 类，2B 和 2C 类钢）；对含氮不锈钢 1B 和 1C 类适用于碳化物固溶处理；1D 类用于从轧制温度快速冷却碳化物固溶处理的材料）。
3.2.2 所需零件的说明（即棒材、螺栓、螺钉或螺柱）。 3.2.3 螺母，如买方需要带螺母，则根据第 13.1 节。 3.2.4 补充要求。 3.2.5 特殊要求，按第 6.3，6.5.1，10.2，14.1 及 15.1 节。 3.3 镀层—除非在采购订单中有规定（见附件要求 S13），镀层是不允许的。当订购有镀层的紧固件时，买方应特别注意保证完全理解附录 X2. 3.4 如本规范要求与规范 A962/A 962M 要求有冲突，本标准要求优先。
注 3：适用于低温使用的合金钢螺栓材料，可参见 A320/A320M 标准。

A193A193M高温设备用合金钢和不锈钢螺栓材料

Designation:A 193/A 193M –04aStandard Speciﬁcation forAlloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service 1This standard is issued under the ﬁxed designation A 193/A 193M;the number immediately following the designation indicates the year of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon (e )indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.Note—Corrections were made throughout editorially and the year date was changed on May 11,2004.1.Scope*1.1This speciﬁcation 2covers alloy and stainless steel bolt-ing material for pressure vessels,valves,ﬂanges,and ﬁttings for high-temperature service.The term bolting material as used in this speciﬁcation covers bars,bolts,screws,studs,stud bolts,and wire.Bars and wire shall be hot-wrought.The material may be further processed by centerless grinding or by cold drawing.Austenitic stainless steel may be carbide solution treated or carbide solution treated and strain-hardened.When strain hardened austenitic steel is ordered,the purchaser should take special care to ensure that Appendix X1is thoroughly understood.1.2Several grades are covered,including ferritic steels and austenitic stainless steels designated B5,B8,and so forth.Selection will depend upon design,service conditions,me-chanical properties,and high-temperature characteristics.N OTE 1—The committee formulating this speciﬁcation has included ﬁfteen steel types that have been rather extensively used for the present purpose.Other compositions will be considered for inclusion by the committee from time to time as the need becomes apparent.N OTE 2—For grades of alloy-steel bolting material suitable for use at the lower range of high-temperature applications,reference should be made to Speciﬁcation A 354.N OTE 3—For grades of alloy-steel bolting material suitable for use in low-temperature applications,reference should be made to Speciﬁcation A 320/A 320M.1.3Nuts for use with this bolting material are covered in Section 13.1.4Supplementary Requirements S1through S10are pro-vided for use when additional tests or inspection are desired.These shall apply only when speciﬁed in the purchase order.1.5This speciﬁcation is expressed in both inch-pound units and in SI units.However,unless the order speciﬁes theapplicable M speciﬁcation designation (SI units),the material shall be furnished to inch-pound units.1.6The values stated in either inch-pound units or SI units are to be regarded separately as standard.Within the text,the SI units are shown in brackets.The values stated in each system are not exact equivalents;therefore,each system must be used independently of the bining values from the two systems may result in nonconformance with the speciﬁ-cation.2.Referenced Documents 2.1ASTM Standards:3A 194/A 194M Speciﬁcation for Carbon and Alloy Steel Nuts for Bolts for High-Pressure or High-Temperature Service,or BothA 320/A 320M Speciﬁcation for Alloy/Steel Bolting Mate-rials for Low-Temperature ServiceA 354Speciﬁcation for Quenched and Tempered Alloy Steel Bolts,Studs,and Other Externally Threaded Fasten-ersA 962/A 962M Speciﬁcation for Common Requirements for Steel Fasteners or Fastener Materials,or Both,Intended for Use at Any Temperature from Cryogenic to the Creep RangeE 18Test Methods for Rockwell Hardness and Rockwell Superﬁcial Hardness of Metallic MaterialsE 21Test Methods for Elevated Temperature Tension Tests of Metallic MaterialsE 112Test Methods for Determining Average Grain Size E 139Test Methods for Conducting Creep,Creep-Rupture,and Stress-Rupture Tests of Metallic MaterialsE 150Practice for Conducting Creep and Creep-Rupture Tension Tests of Metallic Materials Under Conditions of Rapid Heating and Short Times 4E 151Practice for Tension Tests of Metallic Materials at1This speciﬁcation is under the jurisdiction of ASTM Committee A01on Steel,Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.22on Steel Forgings and Wrought Fittings for Piping Applications and Bolting Materials for Piping and Special Purpose Applications.Current edition approved May 11,2004.Published June 2004.Originally approved in st previous edition approved in 2004as A 193/A 193M-04.2For ASME Boiler and Pressure Vessel Code applications,see related Speciﬁ-cation SA-193in Section II of that Code.3For referenced ASTM standards,visit the ASTM website,,or contact ASTM Customer Service at service@.For Annual Book of ASTM Standards volume information,refer to the standard’s Document Summary page on the ASTM website.4Withdrawn.1*A Summary of Changes section appears at the end of this standard.Copyright ©ASTM International,100Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,UnitedStates.Elevated Temperatures with Rapid Heating and Conven-tional or Rapid Strain Rates 4E 292Test Methods for Conducting Time-for-Rupture Notch Tension Tests of MaterialsE 328Test Methods for Stress-Relaxation Tests for Materi-als and StructuresE 381Method of Macroetch Testing Steel Bars,Billets,Blooms,and ForgingsE 566Practice for Electromagnetic (Eddy-Current)Sorting of Ferrous MetalsE 709Guide for Magnetic Particle ExaminationF 606Test Methods for Determining the Mechanical Prop-erties of Externally and Internally Threaded Fasteners,Washers,and Rivets 2.2ANSI Standards:5B1.1Screw ThreadsB18.2.1Square and Hex Bolts and Screws B18.2.3.1M Metric Hex Cap ScrewsB18.3Hexagon Socket and Spline Socket Screws B18.3.1M Metric Socket Head Cap Screws 2.3AIAG Standard:6AIAG B-502.00Primary Metals Identiﬁcation Tag Appli-cation Standard3.General Requirements and Ordering Information3.1Material supplied to this material speciﬁcation shall conform to Speciﬁcation A 962/A 962M.These requirements outline the testing and retesting methods and procedures,permissible variations in dimensions,and mass,quality and repair of defects,etc.3.2It is the purchaser’s responsibility to specify in the purchase order all ordering information necessary to purchase the needed material.Examples of such information include,but are not limited to,the ordering information in Speciﬁcation A 962/A 962M and the following:3.2.1Heat-treated condition (that is,normalized and tem-pered,or quenched and tempered,for the ferritic materials,and carbide solution treated (Class 1),carbide solution treated after ﬁnishing (Class 1A),and carbide solution treated and strain-hardened (Classes 2,2B and 2C),for the austenitic stainless steels;Classes 1B and 1C apply to the carbide solution-treated nitrogen-bearing stainless steels;Class 1D applies to material carbide solution treated by cooling rapidly from the rolling temperature),3.2.2Description of items required (that is,bars,bolts,screws,or studs),3.2.3Nuts,if required by purchaser,in accordance with 13.1,3.2.4Supplementary requirements,if any,and3.2.5Special requirements,in accordance with 6.3,6.5.1,10.2,14.1,and 15.1.3.3If the requirements of this speciﬁcation are in conﬂict with the requirements of Speciﬁcation A 962/A 962M the requirements of this speciﬁcation shall prevail.4.Manufacture (Process)4.1The steel shall be produced by any of the following processes:open-hearth,basic-oxygen,electric-furnace,or vacuum-induction melting (VIM).The molten steel may be vacuum-treated prior to or during pouring of the ingot or strand casting.4.2Quality —See Speciﬁcation A 962/A 962M for require-ments.5.Discard5.1A sufficient discard shall be made to secure freedom from injurious piping and undue segregation.6.Heat Treatment6.1Ferritic steels shall be properly heat treated as best suits the high-temperature characteristics of each grade.Immedi-ately after rolling or forging,the bolting material shall be allowed to cool to a temperature below the cooling transfor-mation range.The materials which are to be furnished in the liquid-quenched condition shall then be uniformly reheated to the proper temperature to reﬁne the grain (a group thus reheated being known as a quenching charge )and quenched in a liquid medium under substantially uniform conditions for each quenching e of water quenching is prohibited for any ferritic grade when heat treatment is part of the fastener manufacturing process.This prohibition does not apply to heat treated bar or to fasteners machined therefrom.Material Grade B16shall be heated to a temperature range from 1700to 1750°F [925to 954°C]and oil quenched.The materials that are to be furnished in the normalized or air-quenched condition shall be reheated to the proper temperature to reﬁne the grain and cooled uniformly in air to a temperature below the transformation temperature range.The material,whether liquid-quenched or normalized,shall then be uniformly re-heated for tempering.The minimum tempering temperature shall be as speciﬁed in Table 2and Table 3.5Available from American National Standards Institute (ANSI),25W.43rd St.,4th Floor,New York,NY 10036.6Available from Automotive Industry Action Group,26200Lahser,Suite 200,Southﬁeld,MI48034.TABLE1Chemical Requirements(Composition,percent)AType.........Ferritic SteelsGrade........B5B6and B6XUNS Designation........5%Chromium12%ChromiumS41000(410)Range Product Variation,Range Product VariationOver or Under B Over or Under B Carbon0.10min0.01under0.08–0.150.01over Manganese,max 1.000.03over 1.000.03over Phosphorus,max0.0400.005over0.0400.005over Sulfur,max0.0300.005over0.0300.005overSilicon 1.00max0.05over 1.00max0.05over Chromium 4.0–6.00.1011.5–13.50.15 Molybdenum0.40–0.650.05...... Type..........Ferritic SteelsGrade......B7,B7M B16 Description.........Chromium-Molybdenum C Chromium-Molybdenum-VanadiumProduct Variation,Product Variation,Range Over or Under B Range Over or Under B Carbon0.37–0.49D0.020.36–0.470.02Manganese0.65–1.100.040.45–0.700.03 Phosphorus,max0.0350.005over0.0350.005over Sulfur,max0.0400.005over0.0400.005overSilicon0.15–0.350.020.15–0.350.02Chromium0.75–1.200.050.80–1.150.05 Molybdenum0.15–0.250.020.50–0.650.03 Vanadium......0.25–0.350.03Aluminum,max%E......0.015...Type Austenitic Steels,F Classes1,1A,1D,and2Grade..B8,B8A B8C,B8CA B8M,B8MA,B8M2,B8M3B8P,B8PA UNS Designation......S30400(304)S34700(347)S31600(316)S30500Range Product Variation,Over or Under BRangeProduct Variation,Over or Under BRangeProduct Variation,Over or Under BRangeProduct Variation,Over or Under BCarbon,max0.080.01over0.080.01over0.080.01over0.120.01over Manganese,max 2.000.04over 2.000.04over 2.000.04over 2.000.04over Phosphorus,max0.0450.010over0.0450.010over0.0450.010over0.0450.010over Sulfur,max0.0300.005over0.0300.005over0.0300.005over0.0300.005over Silicon,max 1.000.05over 1.000.05over 1.000.05over 1.000.05over Chromium18.0–20.00.2017.0–19.00.2016.0–18.00.2017.0–19.00.20 Nickel8.0–11.00.159.0–12.00.1510.0–14.00.1511.0–13.00.15 Molybdenum............ 2.00–3.000.10...... Columbium+......10x carbon0.05under............ tantalum content,min;1.10maxTABLE1ContinuedType..........Austenitic Steels,F Classes1A,1B,1D,and2Grade.....B8N,B8NA B8MN,B8MNA B8MLCuN,B8MLCuNA UNS Designation..........S30451(304N)S31651(316N)S31254Range Product Variation,Over or Under BRangeProduct Variation,Over or Under BRangeCarbon,max0.080.01over0.080.01over0.020 Manganese,max 2.000.04over 2.000.04over 1.00 Phosphorus,max0.0450.010over0.0450.010over0.030 Sulfur,max0.0300.005over0.0300.005over0.010 Silicon,max 1.000.05over 1.000.05over0.80 Chromium18.0–20.00.2016.0–18.00.2019.5–20.5 Nickel8.0–11.00.1510.0–13.00.1517.5–18.5 Molybdenum...... 2.00–3.000.10 6.0–6.5 Nitrogen0.10–0.160.010.10–0.160.010.18–0.22 Copper............0.50–1.00 Type...............................Austenitic Steels F,Classes1,1A,and2Grade..................B8T,B8TAUNS Designation.............................S32100(321)Range Product Variation, Over or Under BCarbon,max0.080.01over Manganese,max 2.000.04over Phosphorus,max0.0450.010over Sulfur,max0.0300.005over Silicon,max 1.000.05over Nickel9.0–12.00.15 Chromium17.0–19.00.20 Titanium5x(C+N)min,0.70max0.05under Type Austenitic Steels F,Classes1C and1DGrade B8R,B8RA B8S,B8SA UNS Designation S20910S21800Range Product Variation,Over or Under BRangeProduct Variation,Over or Under BCarbon,max0.060.01over0.100.01over Manganese 4.0–6.00.057.0–9.00.06 Phosphorus,max0.0450.005over0.0600.005over Sulfur,max0.0300.005over0.0300.005over Silicon 1.00max0.05over 3.5–4.50.15 Chromium20.5–23.50.2516.0–18.00.20 Nickel11.5–13.50.158.0–9.00.10 Molybdenum 1.50–3.000.10...... Nitrogen0.20–0.400.020.08–0.180.01 Columbium+tantalum0.10–0.300.05...... Vanadium0.10–0.300.02......Type Austenitic Steels F,Classes1,1A and1DGrade B8LN,B8LNA B8MLN,B8MLNA UNS Designation S30453S31653Range Product Variation,Over or Under BRangeProduct Variation,Over or Under BCarbon,max0.0300.005over0.0300.005overManganese 2.000.04over 2.000.04overPhosphorus,max0.0450.010over0.0450.010overSulfur,max0.0300.005over0.0300.005overSilicon 1.000.05over 1.000.05overChromium18.0–20.00.2016.0–18.00.20Nickel8.0–11.00.1510.0–13.00.15 Molybdenum...... 2.00–3.000.10Nitrogen0.10–0.160.010.10–0.160.01A The intentional addition of Bi,Se,Te,and Pb is not permitted.B Product analysis—Individual determinations sometimes vary from the speciﬁed limits on ranges as shown in the tables.The several determinations of any individual element in a heat may not vary both above and below the speciﬁed range.C Typical steel compositions used for this grade include4140,4142,4145,4140H,4142H,and4145H.D For bar sizes over31⁄2in.[90mm],inclusive,the carbon content may be0.50%,max.For the B7M grade,a minimum carbon content of0.28%is permitted,provided that the required tensile properties are met in the section sizes involved;the use of AISI4130or4130H is allowed.E Total of soluble and insoluble.FClasses 1and 1D are solution treated.Classes 1,1B,and some 1C (B8R and B8S)products are made from solution treated material.Class 1A (B8A,B8CA,B8MA,B8PA,B8TA,B8LNA,B8MLNA,B8NA,and B8MNA)and some Class 1C (B9RA and B8SA)products are solution treated in the ﬁnished condition.Class 2products are solution treated and strain hardened.TABLE 2Mechanical Requirements —Inch ProductsGrade Diameter,in.Minimum Tempering Temperature,°F Tensile Strength,min,ksiYield Strength,min,0.2%offset,ksiElongation in 4D,min,%Reduction of Area,min,%Hardness,maxFerritic SteelsB54to 6%chromiumup to 4,incl 1100100801650...B613%chromiumup to 4,incl 1100110851550...B6X13%chromiumup to 4,incl 11009070165026HRC B7Chromium-molybdenum21⁄2and under 11001251051650321HB or 35HRC over 21⁄2to 41100115951650321HB or 35HRC over 4to 71100100751850321HB or 35HRC B7M A Chromium-molybdenum4and under 1150100801850235HB or 99HRB over 4to 71150100751850235BHN or 99HRB B16Chromium-molybdenum-vanadium21⁄2and under 12001251051850321HB or 35HRC over 21⁄2to 41200110951745321HB or 35HRC over 4to 81200100851645321HB or 35HRCGrade,Diameter,in.Heat Treatment BTensile Strength,min,ksiYield Strength,min,0.2%offset,ksiElongation in 4D,min %Reduction of Area,min %Hardness,maxAustenitic SteelsClasses 1and 1D;B8,B8M,B8P ,B8LN,carbide solution treated75303050223HB C or 96HRB B8MLN,all diameters Class 1:B8C,B8T,all diameterscarbide solution treated75303050223HB C or 96HRB Class 1A:B8A,B8CA,B8MA,B8PA,B8TA,B8LNA,B8MLNA,B8NA,B8MNAB8MLCuNA,all diameterscarbide solution treated in the ﬁnished condition75303050192HB or 90HRBClasses 1B and 1D:B8N,B8MN,andcarbide solution treated 80353040223HB C or 96HRBB8MLCuN,all diameters Classes 1C and 1D:B8R,all diameterscarbide solution treated 100553555271HB or 28HRC Class 1C:B8RA,all diameters carbide solution treated in the ﬁnishedcondition 100553555271HB or 28HRCClasses 1C and 1D:B8S,all diameterscarbide solution treated95503555271HB or 28HRC Classes 1C:B8SA,carbide solution treated in the ﬁnished 95503555271HB or 28HRC all diametersconditionClass 2:B8,B8C,B8P ,B8T,and B8N,D3⁄4and undercarbide solution treated and strain hardened1251001235321HB or 35HRCover 3⁄4to 1,incl 115801535321HB or 35HRC over 1to 11⁄4,incl 105652035321HB or 35HRC over 11⁄4to 11⁄2,incl100502845321HB or 35HRC Class 2:B8M,B8MN,B8MLCuN D 3⁄4and under carbide solution treated and strain hardened110951545321HB or 35HRC over 3⁄4to 1incl100802045321HB or 35HRCGrade,Diameter,in.Heat TreatmentBTensile Strength,min,ksiYield Strength,min,0.2%offset,ksiElongation in 4D,min %Reduction of Area,min %Hardness,maxAustenitic SteelsOver 1to 11⁄4,incl 95652545321HB or 35HRC over 11⁄4to 11⁄2,incl 90503045321HB or 35HRC Class 2B:B8,B8M2D 2and undercarbide solution treated and strain hardened95752540321HB or 35HRC over 2to 21⁄2incl 90653040321HB or 35HRC over 21⁄2to 3incl 80553040321HB or 35HRC Class 2C:B8M3D 2and undercarbide solution treated and strain hardened85653060321HB or 35HRC over 285603060321HB or 35HRCA To meet the tensile requirements,the Brinell hardness shall be over 200HB (93HRB).BClass 1is solution treated.Class 1A is solution treated in the ﬁnished condition for corrosion resistance;heat treatment is critical due to physical property requirement.Class 2is solution treated and strain hardened.Austenitic steels in the strain-hardened condition may not show uniform properties throughout the section particularly in sizes over 3⁄4in.in diameter.CFor sizes 3⁄4in.in diameter and smaller,a maximum hardness of 241HB (100HRB)is permitted.DFor diameters 11⁄2and over,center (core)properties may be lower than indicated by test reports which are based on values determined at 1⁄2radius.TABLE 3Mechanical Requirements —Metric ProductsClass Diameter,[mm]Minimum Tempering Temperature,°C Tensile Strength,min,MPaYield Strength,min,0.2%offset,MPaElongation in 4D,min,%Reduction of Area,min,%Hardness,maxFerritic SteelsB54to 6%chromium up to M100,incl 5936905501650...B613%chromium up to M100,incl 5937605851550...B6X13%chromium up to M100,incl 593620485165026HRC B7Chromium-molybdenumM64and under 5938607201650321HB or 35HRC over M64to M1005937956551650321HB or 35HRC over M100to M1805936905151850321HB or 35HRC B7M A Chromium-molybdenumM100and under 6206905501850235HB or 99HRB over M100to M1806206905151850235BHN or 99HRB B16Chromium-molybdenum-vanadiumM64and under 6508607251850321HB or 35HRC over M64to M1006507606551745321HB or 35HRC over M100to M1806506905861645321HB or 35HRCClass Diameter,mm Heat Treatment BTensile Strength,min,MPaYield Strength,min,0.2%offset,MPaElongation in 4D,min %Reduction of Area,min %Hardness,maxAustenitic SteelsClasses 1and 1D;B8,B8M,B8P ,B8LN,carbide solution treated 5152053050223HB C or 96HRB B8MLN,all diameters Class 1:B8C,B8T,all diameterscarbide solution treated5152053050223HB C or 96HRB Class 1A:B8A,B8CA,B8MA,B8PA,B8TA,B8LNA,B8MLNA,B8NA,B8MNA B8MLCuNA,all diameterscarbide solution treated in the ﬁnished condition5152053050192HB or 90HRBClasses 1B and 1D:B8N,B8MN,andcarbide solution treated 5502403040223HB C or 96HRB B8MLCuN,all diametersClasses 1C and 1D:B8R,all diameterscarbide solution treated6903803555271HB or 28HRCClass Diameter,mm Heat Treatment BTensileStrength,min,MPaYieldStrength,min,0.2%offset,MPaElongationin4D,min%Reductionof Area,min%Hardness,max Austenitic SteelsClass1C:B8RA,all diameters carbide solution treated in theﬁnishedcondition6903803555271HB or28HRCClasses1C and1D:B8S,all diameters carbide solution treated6553453555271HB or28HRC Classes1C:B8SA,carbide solution treated in theﬁnished6553453555271HB or28HRC all diameters conditionClass2:B8,B8C,B8P,B8T,and B8N,D M20and under carbide solution treated and strainhardened8606901235321HB or35HRCover M20to M24,incl7955501535321HB or35HRC over M24to M30,incl7254502035321HB or35HRC over M30to M36,incl6903452845321HB or35HRCClass2:B8M,B8MN,B8MLCuN,D M20and under carbide solution treated and strainhardened7606551545321HB or35HRCover M20to M24,incl6905502045321HB or35HRC over M24to M30,incl6554502545321HB or35HRC over M30to M36,incl6203453045321HB or35HRCClass2B:B8,B8M2,D M48and under carbide solution treated and strainhardened6555152540321HB or35HRCover M48to M64,incl6204503040321HB or35HRC over M64to M72,incl5503803040321HB or35HRCClass2C:B8M3,D M48and under carbide solution treated and strainhardened5854503060321HB or35HRCover M485854153060321HB or35HRCA To meet the tensile requirements,the Brinell hardness shall be over200HB(93HRB).B Class1is solution treated.Class1A is solution treated in theﬁnished condition for corrosion resistance;heat treatment is critical due to physical property requirement. Class2is solution treated and strain hardened.Austenitic steels in the strain-hardened condition may not show uniform properties throughout the section particularly in sizes over M20mm in diameterC For sizes M20mm in diameter and smaller,a maximum hardness of241HB(100HRB)is permitted.D For diameters M38and over,center(core)properties may be lower than indicated by test reports which are based on values determined at1⁄2radius.6.1.1Quenched and tempered or normalized and tempered ferritic material that is subsequently cold drawn for dimen-sional control shall be stress-relieved after cold drawing.The minimum stress-relief temperature shall be100°F[55°C] below the tempering temperature.Tests for mechanical prop-erties shall be performed after stress relieving.6.2Both B6and B6X materials shall be held,at the tempering temperature for a minimum time of1h.Identiﬁca-tion Symbol B6X material may be furnished in the as-rolled-and-tempered condition.Cold working is permitted with the hardness limitation(26HRC maximum)of Table2for the B6X grade.6.3All austenitic stainless steels shall receive a carbide solution treatment(see6.3.1-6.3.4for speciﬁc requirements for each class).Classes1,1B,1C(Grades B8R and B8S only),2, 2B,and2C can apply to bar,wire,andﬁnished fasteners.Class 1A(all grades)and Class1C(grades B8RA and B8SA only) can apply toﬁnished fasteners.Class1D applies only to bar and wire andﬁnished fasteners that are machined directly from Class1D bar or wire without any subsequent hot or cold working.6.3.1Classes1and1B,and Class1C Grades B8R and B8S—After rolling of the bar,forging,or heading,whether done hot or cold,the material shall be heated from ambient temperature and held a sufficient time at a temperature at which the chromium carbide will go into solution and then shall be cooled at a rate sufficient to prevent the precipitation of the carbide.6.3.2Class1D—Rolled or forged Grades B8,B8M,B8P, B8LN,B8MLN,B8N,B8MN,B8R,and B8S bar shall be cooled rapidly immediately following hot working while the temperature is above1750°F[955°C]so that grain boundary carbides are in solution.Class1D shall be restricted to applications at temperatures less than850°F[455°C].6.3.3Class1A and Class1C Grades B8RA and B8SA—Finished fasteners shall be carbide solution treated after all rolling,forging,heading,and threading operations are com-plete.This designation does not apply to starting material such as bar.Fasteners shall be heated from ambient temperature and held a sufficient time at a temperature at which the chromium carbide will go into solution and then shall be cooled at a rate sufficient to prevent the precipitation of the carbide.6.3.4Classes2,2B,and2C—Material shall be carbide solution treated by heating from ambient temperature and holding a sufficient time at a temperature at which the chromium carbide will go into solution and then cooling at a rate sufficient to prevent the precipitation of the carbide. Following this treatment the material shall then be strain hardened to achieve the required properties.N OTE4—Heat treatment following operations performed on a limited portion of the product,such as heading,may result in non-uniform grain size and mechanical properties through the section affected.6.4If scale-free brightﬁnish is required,this shall be speciﬁed in the purchase order.6.5B7and B7M bolting material shall be heat treated by quenching in a liquid medium and tempering.ForB7Mbolting,theﬁnal heat treatment,which may be the tempering operation if conducted at1150°F[620°C]minimum,shall be done after all machining and forming operations,including thread rolling and any type of cutting.Surface preparation for hardness testing,nondestructive evaluation,or ultrasonic bolt tensioning is permitted.6.5.1Unless otherwise speciﬁed,material for Grade B7may be heat treated by the Furnace,the Induction or the Electrical Resistance method.N OTE5—It should be taken into consideration that stress-relaxation properties may vary from heat lot to heat lot or these properties may vary from one heat treating method to another.The purchaser may specify Supplementary Requirement S8,if stress-relaxation testing is desired. 7.Chemical Composition7.1Each alloy shall conform to the chemical composition requirements prescribed in Table1.7.2The steel shall not contain an unspeciﬁed element for the ordered grade to the extent that the steel conforms to the requirements of another grade for which that element is a speciﬁed element.Furthermore,elements present in concentra-tions greater than0.75weight/%shall be reported.8.Heat Analysis8.1An analysis of each heat of steel shall be made by the manufacturer to determine the percentages of the elements speciﬁed in Section7.The chemical composition thus deter-mined shall be reported to the purchaser or the purchaser’s representative,and shall conform to the requirements speciﬁed in Section7.Should the purchaser deem it necessary to have the transition zone of two heats sequentially cast discarded,the purchaser shall invoke Supplementary Requirement S3of Speciﬁcation A788.9.Mechanical Properties9.1Tensile Properties:9.1.1Requirements—The material as represented by the tension specimens shall conform to the requirements pre-scribed in Table2at room temperature after heat treatment. Alternatively,stainless strain hardened headed fasteners(Class 2,2B,and2C)shall be tested full size after strain hardening to determine tensile strength and yield strength and shall conform to the requirements prescribed in Table2.Should the results of full size tests conﬂict with results of tension specimen tests, full size test results shall prevail.9.1.2Full Size Fasteners,Wedge Tensile Testing—When applicable,see12.1.3,headed fasteners shall be wedge tested full size and shall conform to the tensile strength shown in Table2.The minimum full size breaking strength(lbf)for individual sizes shall be as follows:Ts5UTS3As(1) where:Ts=wedge tensile strength,UTS=tensile strength speciﬁed in Table2,andAs=stress area,square inches,as shown in ANSI B1.1or calculated as follows:As50.785~D–~0.974/n!!2(2)where:D=nominal thread size,andn=the number of threads per inch.9.2Hardness Requirements:9.2.1The hardness shall conform to the requirements pre-scribed in Table2.Hardness testing shall be performed in accordance with either Speciﬁcation A962/A962M or with Test Methods F606.9.2.2Grade B7M—The maximum hardness of the grade shall be235HB or99HRB.The minimum hardness shall not be less than200HB or93HRB.Conformance to this hardness shall be ensured by testing the hardness of each stud or bolt by Brinell or Rockwell B methods in accordance with9.2.1.The use of100%electromagnetic testing for hardness as an alternative to100%indentation hardness testing is permissible when qualiﬁed by sampling using indentation hardness testing. Each lot tested for hardness electromagnetically shall be100% examined in accordance with Practice E566.Following elec-tromagnetic testing for hardness a random sample of a mini-mum of100pieces of each heat of steel in each lot(as deﬁned in12.1.1)shall be tested by indentation hardness methods.All samples must meet hardness requirements to permit acceptance of the lot.If any one sample is outside of the speciﬁed maximum or minimum hardness,the lot shall be rejected and either reprocessed and resampled or tested100%by indenta-tion hardness methods.Product that has been100%tested and found acceptable shall have a line under the grade symbol.9.2.2.1Surface preparation for indentation hardness testing shall be in accordance with Test Methods E18.Hardness tests shall be performed on the end of the bolt or stud.When this is impractical,the hardness test shall be performed elsewhere.10.Workmanship,Finish,and Appearance10.1Bolts,screws,studs,and stud bolts shall be pointed and shall have a workmanlikeﬁnish.Points shall beﬂat and chamfered or rounded at option of the manufacturer.Length of point on studs and stud bolts shall be not less than one nor more than two complete threads as measured from the extreme end parallel to the axis.Length of studs and stud bolts shall be measured fromﬁrst thread toﬁrst thread.10.2Bolt heads shall be in accordance with the dimensions of ANSI B18.2.1or ANSI B18.2.3.1M.Unless otherwise speciﬁed in the purchase order,the Heavy Hex Screws Series should be used,except the maximum body diameter and radius ofﬁllet may be the same as for the Heavy Hex Bolt Series.The body diameter and headﬁllet radius for sizes of Heavy Hex Cap Screws and Bolts that are not shown in their respective tables in ANSI B18.2.1or ANSI B18.2.3.1M may be that shown in the corresponding Hex Cap Screw and Bolt Tables respectively.Socket head fasteners shall be in accordance with ANSI B18.3or ANSI B18.3.1M.11.Retests11.1If the results of the mechanical tests of any test lot do not conform to the requirements speciﬁed,the manufacturer may retreat such lot not more than twice,in which case two additional tension tests shall be made from such lot,all of which shall conform to the requirementsspeciﬁed.。

美标材质规格

ASTM A1-00(2005) 碳素钢T型钢轨规格ASTM A1000-05 特种弹簧质量级碳钢丝及合金钢丝规格ASTM A100-07 硅铁规格ASTM A1001-01(2006) 硅铁规格ASTM A1002-99(2003) 镍-铝有序合金铸件规格ASTM A1003/A1003M-05 冷成形框式构件用金属和非金属镀层碳素钢薄板规格ASTM A1004/A1004M-99(2004) 准备用作冷成形框架构件的金属、涂漆金属和非金属涂敷钢薄板规格ASTM A1005/A1005M-00(2004) 平端纵焊缝和螺旋焊缝双重埋弧焊干线用黑钢管规格ASTM A1006/A1006M-00(2004) 平端激光束焊接干线用黑钢管规格ASTM A1007-02(被ASTM A1007-07代替) 钢丝绳用碳素钢丝规格ASTM A1008/A1008M-07(被ASTM A1008/A1008M-07a 代替) 高强度低合金冷轧碳素结构钢薄板以及可成型性、溶液硬化和可烘烤硬化性经改进的高强度低合金冷轧碳素结构钢薄板规格ASTM A1008/A1008M-07a 高强度低合金冷轧碳素结构钢薄板以及可成型性、溶液硬化和可烘烤硬化性经改进的高强度低合金冷轧碳素结构钢薄板规格ASTM A1009-05 高频(10kHz-1 MHz)电力变压器和滤波感应器用软磁MnZn铁芯材料标准规范ASTM A1010/A1010M-01e1 更高强度马氏体不锈钢厚板、薄板和带材规格ASTM A101-04 铬铁规格ASTM A1011/A1011M-06b(被ASTM A1011/A1011M-07代替) 高强度低合金冷轧碳素结构钢薄板和带材、可成型性经改进的高强度低合金冷轧碳素结构钢薄板和带材以及具有超高强度的低合金冷轧碳素结构钢薄板和带材的规格ASTM A1011/A1011M-07 高强度低合金冷轧碳素结构钢薄板和带材、可成型性经改进的高强度低合金冷轧碳素结构钢薄板和带材以及具有超高强度的低合金冷轧碳素结构钢薄板和带材的规格ASTM A1012-02(2007) 带整体式散热片的铁素体、奥氏体和二相合金钢冷凝器与热交换器无缝管及焊接管的规格ASTM A1013-00(2005) 用伏特计、安培计和瓦特计测定可控温度下软磁芯部件的高频(10 kHz-1 MHz)磁芯损耗的标准试验方法ASTM A1014/A1014M-06 高温工作用沉淀硬化螺栓材料(UNS N07718)规格ASTM A1015-01(2005) 卫生设施用管状产品管内图像检测指南ASTM A1016/A1016M-04A 铁素体合金钢、奥素体合金钢和不锈钢管通用要求规格ASTM A1017/A1017M-07 压力容器用铬钼钨合金钢中厚板规格ASTM A1018/A1018M-06c(被ASTM A1018/A1018M-07代替) 碳素钢、市售钢、拉制钢、结构钢、高强度低合金钢、可成型性经改进的高强度低合金钢以及超高强度钢热轧薄板、带材和特厚卷材规格ASTM A1018/A1018M-07 碳素钢、市售钢、拉制钢、结构钢、高强度低合金钢、可成型性经改进的高强度低合金钢以及超高强度钢热轧薄板、带材和特厚卷材规格ASTM A1019/A1019M-01(2007) 下水道和排水管用聚合物预涂的直径为36英寸或不足36英寸[900 mm]的闭合肋钢管规格ASTM A1019/A1019M-01(被ASTM A1019/A1019M-01(2007)代替) 下水道和排水管用聚合物预涂的直径为36英寸或不足36英寸[900 mm]的闭合肋钢管规格ASTM A1020/A1020M-02 锅炉、过热器、热交换器和冷凝器设备用溶焊碳钢和碳锰钢管道规格ASTM A102-04 钒铁规格ASTM A1021/A1021M-05 高温用马氏体不锈钢锻件和锻坯规格ASTM A1022/A1022M-06 混凝土钢筋用异形及普通不锈钢钢丝和焊接钢丝的规格ASTM A1023/A1023M-02 通用多股绞合碳素钢丝绳规格ASTM A1024/A1024M-02 干线用无缝平端黑钢管规格ASTM A1025-05 铁基合金通用要求规格ASTM A1026-03(废止) 建筑构架中使用的合金钢结构型材规格ASTM A1028-03 压缩机和涡轮机翼剖面用不锈钢棒材规格ASTM A1030/A1030M-05 钢薄板产品平面度特性的测量规程ASTM A1031-05 热轧合金钢、拉制钢和结构合金薄板、带材及特厚卷材规格ASTM A1032-04 预应力混凝土管用冷拉钢丝耐氢脆性的试验方法ASTM A1033-04 亚共析碳钢和低合金钢相变的定量测量与报告规程ASTM A1034/A1034M-05b 测试钢筋用机械钢筋接头的试验方法ASTM A1035/A1035M-07 混凝土配筋用异形及光面低碳铬钢筋规格ASTM A1036-04 用单板测量器测量平轧电工钢的电力频率磁性指南ASTM A1037/A1037M-05 炉内对焊黑色钢制干线用管规格ASTM A1038-05 采用超声波接触阻抗法的便携式硬度试验机规程ASTM A1039/A1039M-04 用双滚筒铸造方法生产的市售热轧结构碳钢薄板规格ASTM A1040-07 规定锻制低合金碳钢及合金碳钢协调标准牌号成份的指南ASTM A1041/A1041M-04 压力容器用高强度铬钼钨合金钢厚板规格ASTM A1042/A1042M-04 下水道和排水沟用复合波纹钢管规格ASTM A1043/A1043M-05 建筑物用低屈服拉伸比结构钢规格ASTM A1044/A1044M-05 混凝土抗剪钢筋用钢螺柱组合件规格ASTM A1046/A1046M-06 用热浸法涂敷锌铝锰合金的薄钢板规格ASTM A1047/A1047M-05 测试管道漏气的试验方法ASTM A1048/A1048M-06 高温用高强度铬钼钨合金钢压力容器锻件规格ASTM A1049/A1049M-06 压力容器和相关部件用铁素体/奥氏体（双工）不锈钢锻件规格ASTM A105/A105M-05 管道设备用碳钢锻件规格ASTM A1053/A1053M-06 铁素体-马氏体焊接不锈钢管规格ASTM A1054-07 烧结陶瓷亚铁盐永磁材料标准规范ASTM A106/A106M-06A 高温用无缝碳钢管规格ASTM A108-03e1 冷加工碳素钢棒规格ASTM A109/A109M-03 冷轧碳（最大0.25%）钢带规格ASTM A111-99A(2004)e1 电话和电报线路用镀锌铁丝规格ASTM A116-05 镀锌钢丝编织栅栏规格ASTM A121-07 镀金属钢制剌钢丝规格ASTM A121-99(2004)(废止,被ASTM A121-07代替) 镀金属钢制剌钢丝规格ASTM A123/A123M-02 钢铁制品镀锌层（热浸镀锌）规格ASTM A125-96(2001)(被ASTM A125-96(2007)代替) 热处理钢螺旋弹簧规格ASTM A125-96(2007) 热处理钢螺旋弹簧规格ASTM A126-04 阀门、法兰和管配件用灰铁铸件ASTM A128/A128M-93(2003) 奥氏体锰钢铸件规格ASTM A131/A131M-07 船用结构钢规格ASTM A132-04 钼铁规格ASTM A134-96(2005) 电熔（弧）焊钢管（尺寸NPS 16及以上）规格ASTM A135/A135M-06 电阻焊钢管规格ASTM A139/A139M-04 电熔(弧)焊钢管(NPS4及以上)规格ASTM A143/A143M-03(被ASTM A143/A143M-07代替) 防止热浸镀锌结构钢制品变脆和检测变脆程序的规程ASTM A143/A143M-07 防止热浸镀锌结构钢制品变脆和检测变脆程序的规程ASTM A144-04 钨铁规格ASTM A146-04 氧化钼制品规格ASTM A148/A148M-05 结构用高强度钢铸件规格ASTM A153/A153M-05 钢铁构件镀锌层（热浸）规格ASTM A159-83(2006) 汽车用灰铁铸件ASTM A167-99(2004) 不锈钢和耐热铬镍钢厚板、薄板及带材规格ASTM A176-99(2004) 不锈钢和耐热铬钢板、薄板及带材规格ASTM A178/A178M-02 电阻焊碳素钢和碳素锰钢锅炉管的规格ASTM A179/A179M-90A(2005) 热交换器和冷凝器用冷拉低碳无缝钢管的规格ASTM A181/A181M-06 通用锻制碳素钢管的规格ASTM A182/A182M-06(被ASTM A182/A182M-07代替) 高温下使用的锻制或轧制合金钢和不锈钢管法兰、锻制管件、阀门及零件规格ASTM A182/A182M-07 高温下使用的锻制或轧制合金钢和不锈钢管法兰、锻制管件、阀门及零件规格ASTM A183-03 碳素钢轨螺栓及螺母规格ASTM A184/A184M-06 混凝土配筋用生产的螺纹钢条网规格ASTM A185/A185M-06e1 混凝土钢筋用普通焊接钢丝规格ASTM A192/A192M-02 高压下使用的无缝碳素钢锅炉管规格ASTM A193/A193M-07 高温或高压及其它特定用途设备用合金钢和不锈钢螺栓材料规格ASTM A194/A194M-07A 高压或高温作业或者高压高温作业用螺栓的碳钢及合金钢螺母的规格ASTM A197/A197M-00(2006) 化铁炉用可锻铸铁ASTM A20/A20M-06 压力容器用中厚钢板的一般要求规格ASTM A2-02 普通型、槽型和防护型碳素钢工字钢轨规格ASTM A203/A203M-97(2003) 镍合金钢压力容器板规格ASTM A204/A204M-03 压力容器用钼合金钢厚板规格ASTM A209/A209M-03 无缝钼碳合金锅炉和过热管规格ASTM A210/A210M-02 锅炉和过热器用无缝中碳钢管规格ASTM A213/A213M-07 锅炉、过热器和换热器用无缝铁素体与奥氏体合金钢管规格ASTM A214/A214M-96(2005) 换热器和冷凝器用电阻焊碳素钢管规格ASTM A216/A216M-04(被ASTM A216/A216M-07代替) 高温作业用适于熔焊的碳素钢铸件规格ASTM A216/A216M-07 高温作业用适于熔焊的碳素钢铸件规格ASTM A217/A217M-07 适合高温受压零件用马氏体不锈钢和合金钢铸件的规格ASTM A220/A220M-99(2004) 珠光体可锻铁.ASTM A225/A225M-03 压力容器用锰钒镍合金钢板规格ASTM A227/A227M-06 机械弹簧用冷拉钢丝规格ASTM A228/A228M-02 乐器用优质弹簧钢丝规格ASTM A229/A229M-99(2005) 机械弹簧用油回火钢丝规格ASTM A230/A230M-05 优质油回火阀弹簧用碳素钢丝规格ASTM A231/A231M-04 铬钒合金钢弹簧钢丝规格ASTM A232/A232M-05 优质阀门簧用铬钒合金钢规格ASTM A234/A234M-07 中温与高温用锻制碳素钢及合金钢管配件的规格ASTM A239-95(2004) 铁或钢制品上镀锌层最薄点的定位规程ASTM A240/A240M-07(被ASTM A240/A240M-07e1代替) 压力容器与普通设备用铬和铬镍不锈钢中厚板、薄板及带材规格ASTM A240/A240M-07e1 压力容器与普通设备用铬和铬镍不锈钢中厚板、薄板及带材规格ASTM A242/A242M-04e1 高强度低合金结构钢规格ASTM A247-06 铁铸件中石墨显微结构评定试验方法ASTM A249/A249M-04A 焊接的奥氏体钢锅炉、过热器、热交换器和冷凝器管规格ASTM A250/A250M-05 锅炉和过热器用电阻焊铁素体合金钢管规格ASTM A252-98(2002) 焊接与无缝钢管桩规格ASTM A254-97(2002) 铜焊钢管规格ASTM A255-02e1 测定钢硬度用端部淬火试验方法ASTM A262-02Ae3 奥氏体不锈钢晶间腐蚀敏感性的检测规程ASTM A263-03 耐腐蚀的包层钢厚板、薄板及带材规格ASTM A264-03 不锈铬镍包层钢厚板、薄板及带材规格ASTM A265-03 镍和镍基合金包层钢厚板规格ASTM A266/A266M-03A 压力容器部件用碳素钢锻件规格ASTM A268/A268M-05A 通用无缝及焊接铁素体和马氏体不锈钢管规格ASTM A269-07 通用无缝奥氏体不锈钢管和焊接奥氏体不锈钢管的规格ASTM A27/A27M-05 通用碳素钢铸件规格ASTM A270-03A 卫生设备用无缝和奥氏体不锈钢管规格ASTM A275/A275M-06 钢锻件的磁粉检查试验方法ASTM A276-06 不锈钢棒材和型材规格ASTM A283/A283M-03(2007) 低和中等抗张强度的碳素钢厚板规格ASTM A283/A283M-03(被ASTM A283/A283M-03(2007)代替) 低和中等抗张强度的碳素钢厚板规格ASTM A285/A285M-03 压力容器用低和中等抗张强度的碳素钢厚板规格ASTM A288-91(2003) 涡轮发电机磁性扣环用碳素钢及合金钢锻件规格ASTM A289/A289M-97(2003) 发动机非磁性扣环用合金钢锻件规格ASTM A29/A29M-05 热锻碳素钢及与合金钢棒的一般要求规格ASTM A290/A290M-05 减速装置环形物用碳钢和合金钢锻件规格ASTM A291/A291M-05 减速装置小齿轮、齿轮及轴用碳钢和不锈钢锻件规格ASTM A295/A295M-05 高碳抗摩擦轴承钢规格ASTM A297/A297M-07 一般用耐热铬铁与镍铬铁合金钢铸件规格ASTM A299/A299M-04 压力容器用锰硅碳钢厚板规格ASTM A3-01(2006) 低、中、高碳素钢(未经热处理的)连接板规格ASTM A302/A302M-03 压力容器用锰钼及锰钼镍合金钢厚板规格ASTM A304-05e2 须符合端部淬火硬度要求的碳钢与合金钢棒材规格ASTM A307-07a 抗拉强度为60000psi的碳素钢螺栓和螺柱的技术规范ASTM A308/A308M-06 热浸法镀锡（铅锡合金）薄钢板规格ASTM A309-01(2007) 用三点试验法测定长镀锌薄钢板镀层的重量成分的试验方法ASTM A309-01(被ASTM A309-01(2007)代替) 用三点试验法测定长镀铅锡薄钢板镀层的重量及成份的方法ASTM A31-04e1 钢铆钉及铆钉和压力容器用棒材ASTM A311/A311M-04 压力容器用钢铆钉和铆钉用钢棒规格ASTM A312/A312M-06 无缝焊接冷加工奥氏体不锈钢管规格ASTM A313/A313M-03 不锈钢弹簧钢丝规格ASTM A314-97(2002) 锻造用不锈及耐热钢坯及钢棒规格ASTM A319-71(2006) 高温无压部件用灰铁铸件ASTM A320/A320M-07 低温用合金钢和不锈钢螺栓材料规格ASTM A322-06(被ASTM A322-07代替) 标准级合金钢棒材规格ASTM A322-07 合金钢棒材.级别ASTM A323-05 硼铁合金规格ASTM A324-73(2004) 钛铁规格ASTM A325-06(被ASTM A325-07代替) 经热处理最小抗拉强度为120/105ksi的热处理钢结构螺栓ASTM A325M-05 经热处理最小抗拉强度为830Mpa的热处理钢结构螺栓ASTM A327-91(2006) 铸铁冲击试验方法ASTM A327M-91(2006) 铸铁冲击试验方法(米制)ASTM A328/A328M-07 钢板桩规格ASTM A333/A333M-05 低温用无缝与焊接钢管规格ASTM A334/A334M-04A 低温用无缝与焊接碳素合金钢管钢管规格ASTM A335/A335M-06 高温用无缝铁素体合金钢管规格ASTM A336/A336M-06A(被ASTM A336/A336M-07代替) 压力与高温部件用合金钢锻件规格ASTM A336/A336M-07 压力与高温部件用合金钢锻件规格ASTM A338-84(2004) 铁路,船舶和其他重型装备在温度达到650华氏度(345摄氏度)时使用的可锻铸铁法兰,管件和阀门零件ASTM A34/A34M-06 磁性材料的抽样和采购试验的标准惯例ASTM A340-03a 有关磁性试验用符号和定义的术语ASTM A341/A341M-00(2005) 用直流磁导计和冲击试验法测定材料的直流磁性能的试验方法ASTM A342/A342M-04 磁铁材料导磁率的试验方法ASTM A343/A343M-03 在电力频率下用瓦特计-安培计-伏特计法(100-1000赫兹)和25 厘米艾普斯亭(EPSTEIN) 机架测定材料的交流电磁性能的试验方法ASTM A345-04 磁设备用平轧电炉钢ASTM A348/A348M-05 用瓦特计--安培计--伏特计法(100-10000赫兹)和25厘米艾普斯亭框测定材料的交流磁性能的试验方法ASTM A350/A350M-04A 管道部件用切口韧性试验要求的碳素钢与低合金钢锻件规格ASTM A351/A351M-06 承压零件用奥氏体、奥氏体-铁素体(复合)钢铸件规格ASTM A352/A352M-06 低温受压零件用铁素体和马氏体钢铸件规格ASTM A353/A353M-04 压力容器用经二次正火及回火处理的含9%镍的合金钢厚板规格ASTM A354-07 淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格ASTM A355-89(2006) 渗氮合金钢棒规格ASTM A356/A356M-05(被ASTM A356/A356M-07代替) 汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件规格ASTM A356/A356M-07 汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件规格ASTM A358/A358M-05 高温设备与通用设备用电熔焊奥氏体铬镍不锈钢管规格ASTM A36/A36M-05 结构碳素钢规格ASTM A363-03 地面架空线用镀锌钢丝绳规格ASTM A367-60(2005) 铸铁的激冷试验方法ASTM A368-95A(2004) 不锈钢钢丝索规格ASTM A369/A369M-06 高温用锻制和镗加工碳素钢管和铁素体合金钢管规格ASTM A370-07(被ASTM A370-07a代替) 钢产品机械测试的试验方法及定义ASTM A370-07a 钢产品机械测试的试验方法及定义ASTM A372/A372M-03 薄壁压力容器用碳素钢及合金钢锻件规格ASTM A376/A376M-06 高温中心站用无缝奥氏体钢管规格ASTM A377-03 球墨铸铁压力管规范索引ASTM A380-06 不锈钢零件、设备及系统的清洁、除锈和钝化规程ASTM A381-96(2005) 高压传输系统用金属弧焊钢管规格ASTM A384/A384M-02(被ASTM A384/A384M-07代替) 钢制组装件热浸镀锌时防翘曲和变形的规程ASTM A384/A384M-07 钢制组装件热浸镀锌时防翘曲和变形的规程ASTM A385-05 提供高质量镀锌层（热浸）的规程ASTM A387/A387M-06A 压力容器用铬钼合金钢厚板规格ASTM A388/A388M-07 大型钢锻件超声波检查规程ASTM A389/A389M-03 适合高温受压部件用经特殊热处理的合金钢铸件规格ASTM A390-06 家禽饲养用镀锌钢丝栅栏结构(六角形与直线形)规格ASTM A391/A391M-01 合金钢链条规格ASTM A392-06(被ASTM A392-07代替) 镀锌钢丝制链环栅栏结构规格ASTM A392-07 根据钢棒成份及机械性能选择钢棒的推荐规程ASTM A394-07 传动塔架用镀锌和裸露钢螺栓ASTM A395/A395M-99(2004) 高温用铁素体球墨铸铁受压铸件ASTM A400-69(2006) 根据钢棒成份及机械性能选择钢棒的推荐规程ASTM A401/A401M-03 铬硅合金钢丝规格ASTM A403/A403M-06(被ASTM A403/A403M-07代替) 锻制奥氏体管不锈钢管配件规格ASTM A403/A403M-07 锻制奥氏体管不锈钢管配件规格ASTM A407-07 冷拉卷绕型弹簧钢丝规格ASTM A407-93(2004)(被ASTM A407-07代替) 冷拉卷绕型弹簧钢丝规格ASTM A409/A409M-01(2005) 腐蚀或高温下使用的大直径奥氏体焊接钢管规格ASTM A411-03 镀锌低碳钢铠装线规格ASTM A413/A413M-01 碳素钢链条规格ASTM A414/A414M-06(被ASTM A414/A414M-07代替) 压力容器用碳素钢薄板规格ASTM A414/A414M-07 室内装饰弹簧装置用冷拉之字型、方型和正弦型钢丝规格ASTM A416/A416M-06 预应力混凝土用无镀层七股钢绞线规格ASTM A417-93(2004) 室内装饰弹簧装置用冷拉之字型、方型和正弦型钢丝规格ASTM A418/A418M-05(被ASTM A418/A418M-07代替) 涡轮机和发动机钢转子锻件超声波检验的试验方法ASTM A418/A418M-07 涡轮机和发动机钢转子锻件超声波检验的试验方法ASTM A420/A420M-07 低温用锻制碳素钢和合金钢管配件规格ASTM A421/A421M-05 预应力混凝土用无镀层应力消失钢丝规格ASTM A423/A423M-95(2004) 无缝和电焊接低合金钢管规格ASTM A424-06 搪瓷用钢薄板规格ASTM A426/A426M-05(被ASTM A426/A426M-07代替) 高温作业用离心浇铸铁素体合金钢管规格ASTM A426/A426M-07 高温作业用离心浇铸铁素体合金钢管规格ASTM A427-02 冷轧与热轧用锻制合金钢轧辊规格ASTM A428/A428M-06 铝覆铁或钢件覆层的重量(质量)的试验方法ASTM A434-06 热轧与冷精轧经淬火及回火的合金钢棒规格ASTM A435/A435M-90(2007) 中厚钢板直射束超声检测规格ASTM A437/A437M-06 高温用经特殊热处理的涡轮型合金钢螺栓材料规格ASTM A439-83(2004) 奥氏体可锻铸铁铸件ASTM A447/A447M-93(2003) 高温用镍铬铁合金钢铸件(25-12级)规格ASTM A449-07a 经淬火和回火的钢螺栓和螺柱ASTM A450/A450M-04A 碳素钢管、铁素体合金钢管及奥氏体合金钢管一般要求规格ASTM A451/A451M-06 高温用离心浇铸奥氏体钢管规格ASTM A453/A453M-04 具有同奥氏体钢相类似膨胀系数的耐高温螺栓材料规格ASTM A455/A455M-03 压力容器用高强度锰碳钢中厚板规格ASTM A456/A456M-99(2003) 大曲轴锻件磁粉探伤规格ASTM A459-97(2003) 镀锌扁钢铠装带规格ASTM A460-94(2004)e1 包铜钢丝绳规格ASTM A463/A463M-06 热浸法铝覆层薄钢板规格ASTM A466/A466M-01 非焊接碳素钢链规格ASTM A467/A467M-01(2006) 机器链和盘旋链规格ASTM A469/A469M-07 发电机转子用经真空处理钢锻件的规格ASTM A47/A47M-99(2004) 铁素体可锻铁铸件ASTM A470/A470M-05e1 涡轮机转子和轴用经真空处理的碳钢和合金钢锻件规格ASTM A471-06 涡轮机转子盘和叶轮用经真空处理的合金钢锻件规格ASTM A472/A472M-05 汽轮机轴和转子锻件热稳定性的试验方法ASTM A473-01 不锈钢及耐热钢锻件规格ASTM A474-03 镀铝钢丝绳规格ASTM A475-03 镀锌钢丝绳规格ASTM A478-97(2002) 铬镍不锈钢和耐热钢制编织钢丝规格ASTM A479/A479M-06A 锅炉及其它压力容器用不锈钢棒材和型材规格ASTM A48/A48M-03 灰铸铁铸件标准技术条件ASTM A480/A480M-06b 平轧不锈钢及耐热钢中厚板、薄板及带材的一般要求规格ASTM A481-05 铬金属规格ASTM A482-05 硅铬铁合金规格ASTM A483-04 硅锰合金规格ASTM A484/A484M-06b 不锈钢棒材、方钢坯和锻件的通用要求规格ASTM A485-03 高硬度减磨轴承钢规格ASTM A487/A487M-93(2003) 受压钢铸件规格ASTM A488/A488M-06(被ASTM A488/A488M-07代替) 钢铸件焊接人员及工艺评定规程ASTM A488/A488M-07 钢铸件焊接人员及工艺评定规程ASTM A489-04e1 碳素钢吊耳ASTM A490-06 最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓ASTM A49-01(2006) 热处理碳钢铁连接杆、微合金连接杆和锻造碳素钢异形连接杆规格ASTM A490M-04ae1 最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓ASTM A491-03 经热处理的碳素钢连接板规格ASTM A492-95(2004) 耐热不锈钢丝绳用钢丝规格ASTM A493-95(2004) 冷镦和冷锻不锈钢和耐热钢丝及钢丝棒规格ASTM A494/A494M-05(被ASTM A494/A494M-07代替) 镍及镍合金铸件规格ASTM A494/A494M-07 镍及镍合金铸件规格ASTM A495-06 硅钙及硅锰钙合金规格ASTM A496/A496M-05 混凝土钢筋用变形钢丝规格ASTM A497/A497M-06e1 混凝土用异形焊接钢丝补强规格ASTM A498-06 无缝与焊接碳素钢,铁素体与奥氏体合金钢制有整体散热片的换热器钢管规格ASTM A499-89(2002) 用T型钢轨轧制的碳素钢棒材及型材的规格ASTM A500-03A 结构用碳素钢冷成形圆截面和异形截面焊接钢管和无缝钢管规格ASTM A501-07 热成型焊接碳钢结构管材和无缝碳钢结构管材规格ASTM A502-03 结构钢铆钉规范ASTM A503/A503M-01(2006) 锻造曲轴超声波检验规格ASTM A504/A504M-07 锻制碳钢轮规格ASTM A505-00(2005) 热轧及冷轧合金钢薄板和带材的一般要求规格ASTM A506-05 热轧和冷轧合金钢及结构合金钢薄板与带材规格ASTM A507-06 热轧和冷轧拉制合金钢薄板及带材规格ASTM A508/A508M-05b 压力容器用淬火和回火真空处理碳素钢和合金钢锻件规格ASTM A510-06 碳素钢盘条和粗圆钢丝的一般要求规格ASTM A510M-06 碳素钢盘条和粗圆钢丝的一般要求规格(米制)ASTM A511-04 无缝不锈钢机械管系的规格ASTM A512-06 冷拉对焊碳素钢机械管规格ASTM A513-07 电阻焊碳素钢与合金钢机械管规格ASTM A514/A514M-05 焊接用经回火与淬火的高屈服强度合金钢中厚板规格ASTM A515/A515M-03 中温及高温压力容器用碳素钢中厚板规格ASTM A516/A516M-06 中温及低温设备用压力容器碳素钢中厚板规格ASTM A517/A517M-06 压力容器用经回火与淬火的高强度合金钢中厚板规格ASTM A518/A518M-99(2003) 耐蚀高硅铁铸件ASTM A519-06 无缝碳素钢与合金钢机械管系规格ASTM A521/A521M-06 一般工业用闭式模锻模锻件规格ASTM A522/A522M-07 低温工作用锻制或轧制含镍8%和9%的合金钢法兰、配件、阀门和零件的规格ASTM A523-96(2005) 高压管型电缆通路用平头端无缝及电阻焊钢管规格ASTM A524-96(2005) 环境温度和低温用无缝碳素钢管规格ASTM A529/A529M-05 优质高强度碳锰结构钢规格ASTM A53/A53M-06A 热浸镀锌黑钢焊接管及无缝管规格ASTM A530/A530M-04A 特种碳素钢及合金钢管一般要求规格ASTM A531/A531M-91(2006) 汽轮发电机钢挡圈的超声波检验规程ASTM A532/A532M-93a(2003) 耐磨铸铁ASTM A533/A533M-93(2004)e1 压力容器用经回火和淬的锰钼及锰钼镍合金钢中厚板规格ASTM A534-04 耐磨轴承用渗碳钢规格ASTM A537/A537M-06 压力容器用经热处理的碳锰硅钢中厚板规格ASTM A540/A540M-06 专用合金钢螺栓连接材料规格ASTM A541/A541M-05 压力容器部件用经淬火和回火的碳素钢及合金钢锻件规格ASTM A542/A542M-99(2004)e1 压力容器用经淬火和回火的铬钼、铬钼钒和铬钼钒钛硼合金钢中厚板规格ASTM A543/A543M-93(2004)e1 压力容器用经淬火和回火的镍铬钼合金钢厚板规格ASTM A550-06 铌铁合金规格ASTM A551/A551M-05(被ASTM A551/A551M-07代替) 铁路和高速运输用碳素钢轮箍规格ASTM A551/A551M-07 铁路和高速运输用碳素钢轮箍规格ASTM A553/A553M-06 压力容器用经回火和淬火的含8%及9%镍的合金钢中厚板规格ASTM A554-03 焊接的不锈钢机械管系规格ASTM A555/A555M-05 不锈钢丝和盘条一般要求规格ASTM A556/A556M-96(2005) 给水加热器冷拉无缝碳素钢管规格ASTM A560/A560M-05 铬镍合金铸件规格ASTM A561-71(2004) 工具钢棒材宏观组织腐蚀试验规程ASTM A562/A562M-06 有玻璃涂层或扩散的金属涂层的压力容器用碳素钢和锰钛合金钢厚板规格ASTM A563M-06 碳素钢及合金钢螺母技术规范(米制)ASTM A564/A564M-04 热锻及冷加工时效硬化不锈及耐热钢棒及型材规格ASTM A565/A565M-05A 高温设备用马氏体不锈钢棒材规格ASTM A568/A568M-06A(被ASTM A568/A568M-07代替) 高强度低合金热轧和冷轧结构碳素钢薄板一般要求规格ASTM A568/A568M-07 高强度低合金热轧和冷轧结构碳素钢薄板一般要求规格ASTM A571/A571M-01(2006) 适用于低温压力容器零件的奥氏体球墨铸铁件ASTM A572/A572M-07 高强度低合金铬钒结构钢规格ASTM A573/A573M-05 增强韧性的结构用碳素钢中厚板规格ASTM A574-04e1 合金钢内六角螺钉ASTM A574M-04e1 合金钢内六角螺钉(米制)ASTM A575-96(2002) 商品级碳素钢棒规格(M级)ASTM A576-90b(2006) 特级热锻碳素钢棒规格ASTM A577/A577M-90(2007) 中厚钢板超声波斜射束检测规格ASTM A578/A578M-96(2001) 直射束超声波检验专用的普通钢板和复合钢板规格ASTM A579/A579M-04A 超强度合金钢锻件规格ASTM A580/A580M-06 耐热不锈钢丝规格ASTM A581/A581M-95b(2004) 易切高速切削用耐热不锈钢丝和钢丝棒规格ASTM A582/A582M-05 易切削不锈钢棒规格ASTM A586-04A 镀锌平行与螺旋钢丝结构索规格ASTM A587-96(2005) 化学工业用电阻焊低碳素钢管规格ASTM A588/A588M-05 4 in. (100 mm)厚屈服点最小为50 ksi /平方英寸(345 MPa)的高强度低合金结构钢规格ASTM A589/A589M-06 无缝焊接碳钢水井管规格ASTM A592/A592M-04 压力容器用经回火和淬火的高强度低合金钢锻制附件及零件规格ASTM A595/A595M-06 结构用锥形低碳钢管或高强度低碳钢管规格ASTM A596/A596M-95(2004) 用环形试验法和冲击法测定材料的直流磁性能的试验方法ASTM A597-87(2004) 铸造工具钢规格ASTM A598/A598M-02 磁放大器磁芯的磁性能测试法ASTM A599/A599M-02 冷轧电解镀锡钢薄板规格ASTM A6/A6M-07 轧制结构钢棒、薄板、中厚板和打板桩的一般要求规格ASTM A600-92A(2004) 高速工具钢规格ASTM A601-05 电解锰金属规格ASTM A602-94(2004) 汽车用可锻铸铁件ASTM A603-98(2003) 镀锌钢丝结构绳规格ASTM A604/A604M-07 自耗电极再溶化钢棒材与钢坯宏观腐蚀试验方法ASTM A604-93(2003)(被ASTM A604/A604M-07代替) 自耗电极再溶化钢棒材与钢坯宏观腐蚀试验方法ASTM A606-04 高强度、低合金、热轧和冷轧且具有较好耐环境腐蚀性的钢、钢板及钢带规格ASTM A608/A608M-06 高温承压设备用铁-铬-镍高合金离心铸造管规格ASTM A609/A609M-91(2002) 碳素低合金马氏体不锈钢铸件的超声波检查规程ASTM A610-79(2004) 铁合金尺寸测量用样品的取样及试验方法ASTM A612/A612M-03 中温及低温压力容器用高强度碳素钢中厚板规格ASTM A615/A615M-07 混凝土钢筋用变形及普通碳素钢棒材规格ASTM A618/A618M-04 热成形焊接及无缝高强度低合金结构管材规格ASTM A623-06A 锡轧制产品一般要求规格ASTM A623M-06A 锡轧制产品的一般要求规格(米制)ASTM A624/A624M-03 一次压延的锡轧制产品和电镀锡薄板规格ASTM A625/A625M-03 一次压延的锡轧制产品和未镀锡的黑钢板规格ASTM A626/A626M-03 二次压延的锡轧制产品和电镀锡薄板规格ASTM A627-03 用于安全用途的均质机床不易加工的钢棒规格ASTM A630-03 测定电镀锡板锡镀层重量的试验方法ASTM A632-04 普通无缝和焊接奥氏体不锈钢管(小直径)规格ASTM A633/A633M-01(2006) 正火的高强度低合金结构钢规格ASTM A635/A635M-06A 高强度低合金及具有经改进可成形性的高强度低合金热轧碳素钢薄板和带材及卷材通用要求规格ASTM A636-76(2004) 氧化镍烧结块规格ASTM A638/A638M-00(2004) 高温作业用沉淀硬化铁基超合金棒材、锻件和锻坯规格ASTM A640-97(2002)e1 8字型电缆架设支架用镀锌钢丝绳规格ASTM A641/A641M-03 镀锌碳素钢钢丝规格ASTM A644-05 铁铸件的相关术语ASTM A645/A645M-05 压力容器用经特殊热处理的5%镍合金钢中厚板规格ASTM A646/A646M-06 航空器与航天器锻件用优质合金钢坯及坯段规格ASTM A648-04ASTM A 预应力混凝土管用冷拔钢丝规格ASTM A649/A649M-04 波纹纸机械用锻制钢辊规格ASTM A650/A650M-03 二次压延的锡轧制品、黑钢板规格ASTM A65-07 钢轨道道钉规格ASTM A653/A653M-06A(被ASTM A653/A653M-07代替) 热浸法镀锌或镀锌铁合金钢薄板规格ASTM A653/A653M-07 热浸处理的镀锌铁合金或镀锌合金薄钢板的标准规范ASTM A656/A656M-05e1 具有经改进的可成形性的热轧结构钢、高强度低合金中厚板规格ASTM A657/A657M-03 一次和二次压延的锡轧制产品及电镀覆铬未镀锡黑钢板的规格ASTM A659/A659M-06 商业级热轧碳素钢薄板和带材(最大含碳量为0.16%-0.25%)规格ASTM A66-07 钢螺纹道钉规格ASTM A660-96(2005) 高温下用离心铸造碳素钢管规格ASTM A662/A662M-03 中低温作业用碳-锰-硅钢压力容器板规格ASTM A663/A663M-89(2006) 机械性能要求的商品级碳素钢棒规格(AASHTO M227/M227M) ASTM A664-06e1 在ASTM规范中对电工钢和层压钢级别的识别ASTM A666-03 退火的或冷加工的奥氏体不锈钢厚钢板、带材、薄板和扁材规格ASTM A667/A667M-87(2003) 离心铸造的双金属(灰口及白口铸铁)圆柱体ASTM A668/A668M-04 一般工业用碳素钢和合金钢锻件规格ASTM A67-00(2005) 低碳钢及高碳钢热加工连接板规格ASTM A671-06 常温和较低温用电熔焊钢管规格ASTM A672-06 中温高压作业用电熔焊钢管规格ASTM A673/A673M-07 结构钢冲击试验用取样方法规格ASTM A674-05 水或其它液体用球墨铸铁管的聚乙烯包装ASTM A675/A675M-03e1 特级热锻碳素钢棒机械性能要求规格ASTM A677-05e1 全处理型无取向电工钢ASTM A678/A678M-05 结构用经回火和淬火的碳素钢和高强度低合金钢中厚板规格ASTM A679/A679M-06 硬拔高抗拉强度钢丝规格ASTM A681-94(2004) 工具钢合金规格ASTM A682/A682M-05 冷轧高碳素钢带材一般要求规格ASTM A683-05e1 半处理型无取向电工钢ASTM A684/A684M-06 冷轧高碳钢带材规格ASTM A686-92(2004) 碳素工具钢规格ASTM A688/A688M-04 给水加热器用奥氏体不锈钢焊接管规格ASTM A689-97(2002) 弹簧用碳素钢及合金钢棒规格ASTM A690/A690M-07 海洋环境用耐大气腐蚀的高强度低合金镍、铜、含磷钢H型桩和钢板桩规格ASTM A691-98(2002) 高温下高压用电熔焊碳素钢和合金钢管规格ASTM A693-06 沉淀硬化耐热不锈钢中厚板、薄板和带材规格ASTM A694/A694M-03 高压传输线用碳素钢及合金钢管法兰、配件、阀门及零件用锻件规格ASTM A696-90A(2006) 压力管系部件用特殊的热锻或冷精轧碳素钢棒规格ASTM A700-05 船运钢产品的包装、标志和装船方法规程ASTM A701-05 硅锰铁规格ASTM A702-89(2006) 热锻钢栅栏柱和组件规格ASTM A703/A703M-07 承压部件用钢铸件通用要求规格ASTM A704/A704M-06 混凝土钢筋用焊接普通钢棒或钢筋网规格。

螺栓性能等级的含义

钢结构连接用螺栓性能等级分3.6、4.6、4.8、5.6、6.8、8.8、9.8、10.9、12.9等10余个等级，其中8.8级及以上螺栓材质为低碳合金钢或中碳钢并经热处理（淬火、回火），通称为高强度螺栓，其余通称为普通螺栓。

螺栓性能等级标号有两部分数字组成，分别表示螺栓材料的公称抗拉强度值和屈强比值。

例如，性能等级4.6级的螺栓，其含义是：1、螺栓材质公称抗拉强度达400MPa级；2、螺栓材质的屈强比值为0.6；3、螺栓材质的公称屈服强度达400×0.6=240MPa级性能等级10.9级高强度螺栓，其材料经过热处理后，能达到：1、螺栓材质公称抗拉强度达1000MPa级；2、螺栓材质的屈强比值为0.9；3、螺栓材质的公称屈服强度达1000×0.9=900MPa级螺栓性能等级的含义是国际通用的标准，相同性能等级的螺栓，不管其材料和产地的区别，其性能是相同的，设计上只选用性能等级即可。

强度等级所谓8.8级和10.9级是指螺栓的抗剪切应力等级为8.8GPa和10.9Gpa另：不锈钢螺栓通常标为A4-70，A2-70的样子，意义另有解释螺纹一、螺纹是一种在固体外表面或内表面的截面上，有均匀螺旋线凸起的形状。

根据其结构特点和用途可分为三大类：（一）、普通螺纹：牙形为三角形，用于连接或紧固零件。

普通螺纹按螺距分为粗牙和细牙螺纹两种，细牙螺纹的连接强度较高。

（二）、传动螺纹：牙形有梯形、矩形、锯形及三角形等。

（三）、密封螺纹：用于密封连接，主要是管用螺纹、锥螺纹与锥管螺纹。

二、螺纹配合等级：螺纹配合是旋合螺纹之间松或紧的大小，配合的等级是作用在内外螺纹上偏差和公差的规定组合。

（一）、对统一英制螺纹，外螺纹有三种螺纹等级：1A、2A和3A级，内螺纹有三种等级：1B、2B和3B级，全部都是间隙配合。

等级数字越高，配合越紧。

在英制螺纹中，偏差仅规定1A和2A级，3A级的偏差为零，而且1A和2A级的等级偏差是相等的。

ASTM钢管标准1

ASTM钢管标准1A1000-99 弹簧专用碳钢和合金钢钢丝规范A1001-99 大型材高强度钢铸件规范A1002-99 镍铝类合金铸件规范A100-93(2000) 硅铁A101-93(2000) 铬铁A102-93(2000) 钒铁合金A105/A105M-01 管系部件用碳素钢锻件A106-999e1 高温用无缝碳素钢管A108-99 优质冷加工碳素钢棒材技术规范A109/A109M-00e1 冷轧碳素钢带技术规范A111-99a 电话和电报线路用镀锌"铁"丝规格A116-00 镀锌钢丝编织栏栅网A121-99 镀锌刺钢丝A123/A123M-00 钢铁产品的锌镀层（热浸镀锌）技术规范A125-96 热处理螺旋形钢弹簧A126-95(2001) 阀门、法兰和管配件用灰铁铸件A128/A128M-93(1998) 钢铸件,奥氏体锰A131/A131M-94 海船用结构钢A132-89(2000) 钼铁合金A134-96 电熔(电弧)焊钢管(NPS为16英寸和16英寸以上)A135-01 电阻焊钢管A139-00 电熔(电弧)焊钢管(4英寸以上的)A143-74(1999) 热浸镀锌结构钢制品防脆裂措施和探测脆裂的程序A146-64(2000) 氧化钼制品A148/A148M-01 结构用高强度钢铸件A153/A153M-00 钢铁制金属构件上镀锌层(热浸)A159-83(2001) 汽车用灰铁铸件A167-99 不锈钢和耐热铬镍钢板、薄板及带材A176-99 不锈钢和耐热铬钢板、薄板及带材A178/A178M-95(2000) 电阻焊接碳素钢钢管及碳锰钢锅炉和过热器管的技术规范A179/A179M-90a(1996)e1 热交换器和冷凝器用无缝冷拉低碳钢管A181/A181M-01 普通锻制碳素钢管的规格A182/A182M-01 高温设备用锻制或轧制的合金钢管法兰、锻制管件、阀门及零件A183-98 钢轨用碳素钢螺栓和螺母A184/A184M-01 混凝土加筋用变形钢筋编织网A185-97 钢筋混凝土用焊接钢丝结构A1-00 碳素钢丁字轨A192/A192M-91(1996)e1 高压用无缝碳素钢锅炉管A193/A193M-01 高温设备用合金钢和不锈钢螺栓材料A194/A194M-01 高温和高压设备用碳素钢与合金钢螺栓和螺母的规格A197/A197M-00 化铁炉用可锻铸铁A20/A20M-01 压力容器用钢板材通用要求A202/A202M-93(1999) 压力容器用铬锰硅合金钢板A203/A203M-97 压力容器用镍合金钢板A204/A204M-93(1999) 压力容器用钼合金钢板A209/A209M-98 锅炉和过热器用无缝碳钼合金钢管A210/A210M-96 锅炉和过热器用无缝中碳素管A213/A213M-01 无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管A214/A214M-96 热交换器与冷凝器用电阻焊接碳素钢管A216/A216M-93(1998) 高温下使用的适合于熔焊的碳素钢铸件规格A217/A217M-01 适合高温受压零件用合金钢和马氏体不锈钢铸件A21-94(1999) 铁路用未经热处理和经热处理的碳素钢轴A220/A220M-99 珠光体可锻铁A225/A225M-93(1999) 压力容器用锰矾镍合金钢板A227/A227M-99 机械弹簧用冷拉钢丝A228/A228M-00 乐器用优质弹簧钢丝A229/A229M-99 机械弹簧用油回火的钢丝A230/A230M-99 阀门用油回火优质碳素钢弹簧丝A231/A231M-96 铬钒合金钢弹簧丝A232/A232M-99 阀门用优质铬钒合金钢弹簧丝A234/A234M-00a 中温与高温下使用的锻制碳素钢及合金钢管配件A239-95(1999) 用普力斯试验法(硫酸铜浸蚀)确定铁或钢制品上镀锌层最薄点的测试方法A240/A240M-01 压力容器用耐热铬及铬镍不锈钢板、薄板及带材A242/A242M-00a 高强度低合金结构钢A247-67(1998) 铁铸件中石墨显微结构评定试验方法A249/A249M-01 锅炉、过热器、换热器和冷凝器用焊接奥氏体钢管A250/A250M-95(2001) 锅炉和过热器用电阻焊铁素体合金钢管A252-98e1 焊接钢和无缝钢管桩A254-97 铜焊钢管规格A255-99 测定钢淬透性用末端淬火试验的标准试验方法A262-98 奥氏体不锈钢晶间浸蚀敏感性的检测A263-94a(1999) 耐腐蚀铬钢包覆板材,薄板材及带材技术规范A264-94a(1999) 包覆的不锈铬镍钢板,薄板及带材规格A265-94a(1999) 镍和镍基合金包覆钢板规格A266/A266M-99 压力容器部件用碳素钢锻件规格A268/A268M-01 一般设备用无缝和焊接铁素体与马氏体不锈钢管A269-01 一般设备用无缝和焊接奥氏体不锈钢管A27/A27M-95(2000) 通用碳素钢铸件A270-01 卫生设施用无缝钢和焊接奥氏体不锈钢管A275/A275M-98 钢锻件的磁粉检查试验方法A276-00a 不锈钢棒材和型材A278-93 适用于650F容压部件用灰铸铁件的技术规范A283/A283M-00 低和中等抗拉强度碳素钢板A285/A285M-90(2001) 压力容器用低和中等抗拉强度的碳素钢板A288-91(1998) 涡轮发电机磁性定位环用碳素钢和合金钢锻件A289/A289M-97 发电机非磁性定位环用合金钢锻件的技术规范A29/A29M-99e1 热锻及冷加工碳素钢和合金钢棒A2-90(1997) 普通型,带槽和防护型碳素工字钢轨A290-95(1999) 减速器环用碳素钢和合金钢锻件A291-95(1999) 减速器小齿轮、齿轮和心轴用碳素钢和合金钢锻件A295-98 高碳耐磨轴承钢技术规范A297/A297M-97(1998) 一般用耐热铬铁与镍铬铁合金钢铸件规格A299/A299M-97e1 压力容器用锰硅碳钢板A302/A302M-97e1 压力容器用锰钼和锰钼镍合金钢板A304-96 有末端淬火淬透性要求的合金钢棒材的技术规范A307-00 抗拉强度为60000psi的碳素钢螺栓和螺柱的技术规范A308-99 经热浸处理镀有铅锡合金的薄板材的技术规范A309-94a(1999) 用三点试验法测定长镀锌薄钢板镀层的重量成分的试验方法A311/A311M-95(2000) 有机械性能要求的消除应力的冷拉碳素钢棒A312/A312M-00c 无缝和焊接奥氏体不锈钢管A313/A313M-98 不锈钢弹簧丝技术规范A314-97 锻造用不锈及耐热钢坯及钢棒规格A31-00 钢铆钉及铆钉和压力容器用棒材A319-71(2001) 高温无压部件用灰铁铸件A320/A320M-01 低温用合金钢螺栓材料规格A321-90(1995)e1 经淬火和回火的碳素钢棒A322-91(1996) 合金钢棒材.级别A323-93(2000) 硼铁规格A324-73(2000) 钛铁合金A325-00 经热处理最小抗拉强度为120/105ksi的钢结构螺栓A325M-00 结构钢连接件用高强度螺栓(米制)A327-91(1997) 铸铁冲击试验方法A327M-91(1997) 铸铁冲击试验方法(米制)A328/A328M-00 薄钢板桩A331-95(2000) 冷加工合金钢棒A333/A333M-99 低温用无缝与焊接钢管规格A334/A334M-99 低温设备用无缝与焊接碳素和合金钢管A335/A335M-01 高温用无缝铁素体合金钢管A336/A336M-99e1 压力与高温部件用合金钢锻件规格A338-84(1998) 铁路,船舶和其他重型装备在温度达到650华氏度(345摄氏度)时使用的可锻铸铁法兰,管件和阀门零件ASTM钢管标准2A34/A34M-96 磁性材料的抽样和采购试验的标准惯例A340-99a 有关磁性试验用符号和定义的术语A341/A341M-00 用直流磁导计和冲击试验法测定材料的直流磁性能的试验方法A342/A342M-99 磁铁材料导磁率的试验方法A343-97 在电力频率下用瓦特计-安培计-伏特计法(100-1000赫兹)和25 厘米艾普斯亭(EPSTEIN) 机架测定材料的交流电磁性能的试验方法A345-98 磁设备用平轧电炉钢A348/A348M-00 用瓦特计--安培计--伏特计法(100-10000赫兹)和25厘米艾普斯亭框测定材料的交流磁性能的试验方法A350/A350M-00c 要求进行缺口韧性试验的管道部件用碳素钢与低合金钢锻件技术规范A351/A351M-00 容压零件用奥氏体及奥氏体铁素体铸铁的技术规范A352/A352M-93(1998) 低温受压零件用铁素体和马氏体钢铸件规格A353/A353M-93(1999) 压力容器用经二次正火及回火处理的含9％镍的合金钢板A354-01 淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格A355-89(2000) 渗氮用合金钢棒A356/A356M-98e1 蒸汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件A358/A358M-01 高温用电熔焊奥氏体铬镍合金钢管A36/A36M-00a 碳素结构钢技术规范A363-98 地面架空线用镀锌钢丝绳A367-60(1999) 铸铁的激冷试验方法A368-95a(2000) 不锈钢和耐热钢丝绳的标准A369/A369M-01 高温用锻制和镗孔碳素钢管和铁素体合金钢管A370-97a 钢制品机械测试的标准试验方法和定义A372/A372M-99 薄壁压力容器用碳素钢及合金钢锻件A376/A376M-01 高温中心站用无缝奥氏钢管A377-99 球墨铸铁压力管规范索引A380-99e1 不锈钢零件、设备和系统的清洗和除垢A381-96 高压输送用金属弧焊钢管A384-76(1996) 防止钢组件热浸镀锌时翘曲和扭曲用安全保护A385-00 提供高质量镀锌覆层(热浸)A3-01 低、中、高碳素钢鱼尾（连接）板A387/A387M-99e1 压力容器用铬钼合金钢板A388/A388M-95(2000)e1 重型钢锻件超声波检测A389/A389M-93(1998) 适合高温受压部件用经特殊热处理的合金钢铸件规格A390-95(2001) 饲养家禽用镀锌钢丝栏栅网(六角形和直线形)A391/A391M-98 80号合金钢链条A392-96 镀锌钢丝链环栏栅网A394-00 传动塔架用镀锌和裸露钢螺栓A395/A395M-99 高温用铁素体球墨铸铁受压铸件A400-69(2000) 钢棒的成分及机械性能选择指南A401/A401M-98 铬硅合金钢丝A403/A403M-00b 锻制奥氏体不锈钢管配件A407-93(1998) 盘簧用冷拉钢丝A409/A409M-01 腐蚀场所或高温下使用的焊接大口径奥氏体钢管A411-98 镀锌低碳钢铠装线A413/A413M-00 碳素钢链A414/A414M-00 压力容器用碳素薄钢板A416/A416M-99 预应力混凝土用无涂层七股钢铰线A417-93(1998) 之字型、方型和正弦型装垫弹簧元件用冷拉钢丝A418-99 涡轮机及发电机钢转子锻件的超声波检查方法A420/A420M-00b 低温下用锻制碳素钢和合金钢管配件A421/A421M-98a 预应力混凝土用无涂层消除应力钢丝的技术规范A423/A423M-95(2000) 无缝和电焊低合金钢管A424-00 搪瓷用钢薄板A426-92(1997) 高温用离心铸造的铁素体合金钢管A427-74(1996)e1 冷轧和热轧用锻制合金钢辊A428/A428M-01 钢铁制品上铝覆层重量的测试方法A434-90a(2000) 热轧与冷精轧经回火及淬火的合金钢棒A435/A435M-90(2001) 钢板的直射束纵向超声波检验A436-84(1997)e1 奥氏体灰口铁铸件A437/A437M-01 高温用经特殊处理的涡轮型合金钢螺栓材料A438-80(1997) 灰铸铁横向弯曲试验A439-83(1999) 奥氏体可锻铸铁铸件A447/A447M-93(1998) 高温用镍铬铁合金钢铸件(25-12级)A449-00 经淬火和回火的钢螺栓和螺柱A450/A450M-96a 碳素钢管、铁素体合金钢管及奥氏体合金钢管A451-93(1997) 高温用离心铸造的奥氏体钢管A453/A453M-00 具有同奥氏体钢相类似的膨胀系数、屈服强度为50-120Ksi(345-827MPa)的耐高温螺栓材料A455/A455M-90(2001) 压力容器用高强度碳锰钢板A456/A456M-99 大型曲轴锻件的磁粉检查A459-97 镀锌平轧扁钢铠装带A460-94(1999) 包铜钢丝绳标准A463/A463M-00 热浸镀铝薄钢板A466/A466M-98 非焊接碳素钢链A467/A467M-98 机器链和盘旋链A469-94a(1999) 用于发电机转子的真空处理钢锻件A470-01 涡轮机转子和轴用经真空处理的碳素钢和合金锻件A471-94(1999) 涡轮转子转盘和转轮用真空处理合金钢锻件技术规范A472-98 蒸汽涡轮机轴及转子锻件的热稳定性的试验方法A473-01 不锈和耐热钢锻件A474-98 包铝钢丝绳标准A475-98 镀锌钢丝绳A476/A476M-00 造纸厂干燥辊用球墨可锻铸铁件A478-97 铬镍不锈钢和耐热钢制编织钢丝A479/A479M-00 锅炉及压力容器用不锈钢和耐热钢棒与型材A47/A47M-99 铁素体可锻铁铸件A480/A480M-01 扁平轧制耐热不锈钢厚板材、薄板材和带材通用要求A481-94(2000) 金属铬A482-93(2000) 铬铁硅A483-64(2000) 硅锰合金A484/A484M-00 不锈及耐热锻钢棒,钢坯及锻件的规格A485-00 高淬透性耐磨轴承钢的技术规范A487/A487M-93(1998) 受压钢铸件A488/A488M-01 钢铸件焊接规程和工作人员的合格鉴定A48-94ae1 灰铁铸件A489-00 碳素钢吊耳A490-00 最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓A491-96 镀铝钢链环栏栅结构A492-95(2000) 耐热不锈钢丝绳A493-95(2000) 冷镦和冷锻不锈钢和耐热钢丝A494/A494M-00 镍和镍合金铸件A495-94(2000) 硅钙合金钢技术规范A496-97ae1 钢筋混凝土用变形钢丝A497-99e1 钢筋混凝土用焊接变形钢丝网A498-98 无缝与焊接碳素钢,铁素体钢与奥氏体钢制有整体散热片的换热器钢管A49-01 经热处理的碳素钢鱼尾（连接）板，微合金鱼尾板及锻制碳素钢异型鱼尾板A499-89(1997)e1 轧制丁字钢轨用的碳素钢棒材及型材的技术规范A500-01 圆形与异型焊接与无缝碳素钢结构管A501-01 热成型焊接与无缝碳素钢结构管A503/A503M-01 锻制大型曲轴的超声波检验A504-93(1999) 锻制碳素钢轮A505-00 热轧和冷轧合金钢薄板和带材A506-00 正规质量及优质结构的热轧和冷轧合金钢薄板与带材A507-00 优质拉拔,热轧和冷轧合金钢薄板与带材A508/A508M-95(1999) 压力容器用经回火和淬火真空处理的碳素钢与合金钢锻件A510-00 碳素钢盘条和粗圆钢丝通用要求A510M-00 碳素钢盘条和粗圆钢丝(米制)A511-96 无缝不锈钢机械管A512-96 冷拉对缝焊碳素钢机械管A513-00 电阻焊碳素钢与合金钢机械钢管A514/A514M-00a 焊接用经回火与淬火的高屈服强度合金钢板A515/A515M-92(1997) 中温及高温压力容器用碳素钢板A516/A516M-90(2001) 中温及低温压力容器用碳素钢板A517/A517M-93(1999) 压力容器用经回火与淬火的高强度合金钢板A518/A518M-99 耐蚀高硅铁铸件A519-96 无缝碳素钢与合金钢机械管A521-96 一般工业用闭式模钢锻件A522/A522M-95b(2000) 低温用锻制或轧制含镍8%和9%的合金钢法兰,配件,阀门和零件规格A523-96 高压管型电缆线路用平端无缝与电阻焊钢管A524-96 常温和低温用无缝碳素钢管A529/A529M-00 高强度碳锰结构钢质量A530/A530M-99e1 特种碳素钢和合金钢管A531/A531M-91(1996) 涡轮发电机钢定位环的超声波检验A532/A532M-93a(1999)e1 耐磨铸铁A533/A533M-93(1999) 压力容器用经回火和淬火的锰钼及锰钼镍合金钢板A534-94 用于耐摩擦轴承的渗碳钢A536-84(1999)e1 球墨铸铁件A537/A537M-95(2000) 压力容器用经热处理的碳锰硅钢板A53/A53M-01 无镀层热浸的、镀锌的、焊接的及无缝钢管的技术规范A539-99 天然气和燃料油管线用电阻焊钢盘管A540/A540M-00 特殊用途的合金钢螺栓材料A541/A541M-95(1999) 压力容器部件用经淬火和回火的碳素钢及合金钢锻件A542/A542M-99e1 压力容器用经回火和淬火的铬钼、铬钼钒及铬钼钒钛硼合金钢板A543/A543M-93(1999) 压力容器用经回火和淬火的镍铬钼合金钢板A550-78(2000) 铌铁合金A551-94(1999) 钢轮箍A553/A553M-95(2000) 压力容器用经回火和淬火的含8%及9%镍的合金钢板A554-98e1 焊接的无缝钢机械管A555/A555M-97 耐热不锈钢丝和盘条的通用要求A556/A556M-96 无缝冷拉碳素钢给水加热器管A560/A560M-93(1998) 铬镍合金铸件A561-71(1999) 工具钢棒的宏观刻蚀试验A562/A562M-90(2001) 搪玻璃或扩散金属镀层的压力容器用锰钛合金碳素钢板A563-00 碳合金钢螺母ASTM钢管标准3A563M-00 碳素钢及合金钢螺母技术规范（米制）A564/A564M-01 热轧及冷精轧时效硬化处理过的不锈钢棒材和型材技术规范A565-97 高温用马氏体不锈钢棒,锻件和锻制坯规格A568/A568M-00b 热轧及冷轧高强度低合金碳素钢薄板A571-84(1997) 适用于低温压力容器零件的奥氏体球墨铸铁件A571M-84(1997) 适用于低温压力容器零件的奥氏体球墨铸铁件(米制)A572/A572M-00a 高强度低合金钴钒结构钢技术规范A573/A573M-00a 增强韧性的结构碳素钢板A574-00 合金钢内六角螺钉A574M-00 合金钢内六角螺钉(米制)A575-96 商品级碳素钢棒(M级)A576-90b(2000) 特级热轧碳素钢棒A577/A577M-90(2001) 钢板的超声角波束检验A578/A578M-96(2001) 特殊设备用的普通钢板和包覆钢板的直波束超声探伤检验A579-99 超高强度合金钢锻件A580/A580M-98 耐热不锈钢丝A581/A581M-95b(2000) 高速切削用耐热不锈钢丝和盘条A582/A582M-95b(2000) 热轧或冷精轧的高速切削不锈及耐热钢棒A583-93(1999) 铁路用铸钢轮A584-97 镀铝钢丝编织栅栏网A585-97 镀铝刺钢丝A586-98 镀锌平行和螺旋形钢丝绳A587-96 化学工业用电阻焊低碳钢管A588/A588M-00a 高强度低合金结构钢4英寸(100mm)厚屈服点最小为50ksi(345MPa) A589-96 水井用无缝和焊接碳素钢管A591/A591M-98 薄镀层电解镀锌薄钢板A592/A592M-89(1999) 压力容器用经回火和淬火的高强度低合金钢锻制附件和零件A595-98 结构用圆锥形低碳钢管A596/A596M-95(1999) 用环形试验法和冲击法测定材料的直流磁性能的试验方法A597-87(1999) 铸造工具钢A598-92(1997) 磁放大器磁芯的磁性能测试法A599/A599M-99 锡制品，电解镀锡的冷滚轧薄板规范A6/A6M-01 轧制结构钢板材、型材和薄板桩通用技术要求A600-92a(1999) 高速工具钢A601-96(2000) 电解金属锰A602-94(1998) 汽车用可锻铸铁件A603-98 镀锌结构钢丝绳A604-93(1998) 自耗电极再溶化钢棒与钢坯的宏观腐蚀试验方法A606-98 改进防大气腐蚀性的热轧和冷轧高强度低合金钢薄板和带材A608-91a(1998) 高温受压离心铸造的铁铬镍高合金钢管A609/A609M-91(1997) 碳素钢,低合金钢和马氏体不锈钢铸件的超声波检测A610-79(2000) 尺寸测量用铁合金的取样和试验A611-00 冷轧优质碳素结构钢薄板A612/A612M-00 中温和低温压力容器用高强度碳素钢板A615/A615M-01a 钢筋混凝土配筋用变形和光面坯钢筋A618-01 热成型焊接与无缝高强度低合金结构钢管系A623-00 锡轧制产品A623M-00 镀锡薄钢板轧制品通用要求(米制)A624/A624M-98 锡辊轧制品.单压延电解马口铁A625/625M-98 一次轧制原钢板（未镀）和镀锡薄钢板轧制产品技术规范A626/A626M-98 二次压延电解镀锡厚钢板轧制品技术规范A626/A626M-98 锡轧制品.二次压延的电解镀锡板(米制)A627-95 安全设备用均质不易加工的钢棒A629-88(1994)e1 安全设备用不易加工的扁钢棒和型材A630-98 热浸电解镀锡板镀锡层重量测定的方法A632-01 通用无缝和焊接奥氏体不锈钢管(小直径)A633/A633M-00a 正火的高强度低合金结构钢A635/A635M-00 热轧碳素钢薄板,带材和重型粗盘条规格A636-76(2000) 氧化镍烧结块A638/A638M-00 高温用沉积硬化铁基超级合金棒,锻件及锻坯料A640-97 8字型缆吊架用镀锌钢丝绳A641/A641M-98 镀锌（电镀）碳素钢丝技术规范A644-98 铁铸件的相关术语A645/A645M-99a 压力容器用经特殊热处理的5%镍合金钢板A646-95(1999) 飞机及航空器锻件用优质合金钢大方坯及坯段A648-95(2000) 预应力混凝土管用冷拉钢丝A649/A649M-99 波纹纸机械用锻制钢辊规格A650/A650M-98 二次压延的锡轧黑板材A653/A653M-00 热浸处理的镀锌铁合金或镀锌合金薄钢板的标准规范A656/A656M-00a 具有改良可模锻性的高强度低合金热轧结构钢板A657/A657M-98a 一次和二次压延电解镀铬黑钢板轧制品技术规范A65-01 钢轨道钉A659/A659M-97 商业级热轧碳素钢薄板和带材(最大含碳量为0.16%-0.25%) A660-96 高温用离心铸造碳素钢管A662/A662M-99 中温和低温压力容器用锰碳钢板规格A663/A663M-89(2000) 商品级碳素钢棒的机械特性A664-99 在ASTM规范中对电工钢和层压钢级别的识别A666-00 退火或冷加工的奥氏体不锈钢薄板、带材、中厚板和扁棒A667/A667M-87(1998) 离心铸造的双金属(灰口及白口铸铁)圆柱体A668/A668M-96e1 一般工业用碳素钢和合金钢锻件A66-01 钢质螺旋道钉A671-96 常温和较低温用电熔焊钢管A672-96 中温高压用电熔焊钢管A673/A673M-95 结构钢冲击试验的取样程序A674-00 水或其它液体用球墨铸铁管的聚乙烯包装A675/A675M-90a(2000) 专用热轧碳素钢棒的机械特性A677/A677M-99 全处理型无取向电工钢A678/A678M-00a 结构用经回火和淬火的高强度低合金碳素钢板规格A679/A679M-00 硬(冷)拉高抗拉强度钢丝A67-00 热加工低碳钢和高碳钢垫板技术规范A681-94(1999) 合金工具钢A682/A682M-00 弹簧用冷轧高碳钢带材A683/A683M-99 半处理型无取向电工钢A684/A684M-99 冷轧高碳钢带材A686-92(1999) 碳素工具钢A688/A688M-01 焊接的奥氏体不锈钢给水加热器管A689-97 弹簧用碳素钢及合金钢棒A690/A690M-00a 在海洋环境中使用的高强度低合金工字形钢桩和薄板桩规格A691-98 高温下高压装置用电熔焊碳素钢和合金钢管A693-93(1999) 沉淀硬化耐热不锈钢板、薄板和带材A694/A694M-00 高压传输设备用碳素钢及合金钢管法兰、配件、阀门及零件用锻件A695-90b(1995)e1 流体动力设备专用热锻碳素钢棒A696-90a(2000) 压力管道部件专用热锻或冷精轧碳素钢棒A697-98 用伏特计、安培计和瓦特计法测定迭层铁芯样品的交流磁特性的试验方法A698/A698M-92(1997)e1 在弱交流磁场中磁屏蔽效率的试验方法A700-99e1 钢制品国内装运的包装、标记和装载方法A701-96(2000) 硅锰铁A702-89(2000) 热锻钢栅栏柱和组件A703/A703M-01 受压部件用钢铸件A704/A704M-96 混凝土加筋用焊接普通钢棒或杆的光面钢筋或钢筋网A705/A705M-95(2000) 时效硬化的不锈和耐热钢锻件A706/A706M-01 混凝土配筋用变形低合金光面无节钢筋A707/A707M-00a 低温设备用锻制碳素钢和合金钢法兰A709/A709M-01 桥梁用结构钢A710/A710M-00 低碳时效硬化的镍铜铬钼铌合金钢A711-92(1996)e1 钢锻件坯料A712-97 软磁性合金电阻率的测试方法A713-93(1998) 热处理部件用高碳弹簧钢丝A714-99 高强度低合金焊接钢管和无缝钢管A716-99 球墨铸铁涵洞管A717/A717M-95 单片样品表面绝缘电阻率的试验方法A719-97 磁性材料的叠装系数的试验方法A720-97 无取向电工钢延展性的试验方法A721-97 取向的电工钢的延展性试验方法A722/A722M-98 预应力混凝土用无涂覆的高强度钢筋A723/A723M-94(1999) 高强度压力元件用合金钢锻件A724/A724M-99 叠层焊接的压力容器用经淬火及回火的碳素钢压力容器板A726-00 半成品型冷轧磁性迭片级钢A727/A727M-00 具有固定切口韧性的管道部件用碳素钢锻件A729-93(1999) 货物运输及电气铁路用热处理合金钢轴A730-93(1999) 铁路用碳素钢及合金钢锻件A732/A732M-98 一般设备用熔模铸造碳素低合金钢及高强度加温钴合金钢铸件A733-99 焊接及无缝碳素钢和奥氏体不锈钢管接头A734/A734M-87a(1997) 经淬火和回火的合金钢与高强度低合金钢压力容器板A735/A735M-99 中温和低温用低碳锰钼钶合金钢压力容器板A736/A736M-88(2000) 低碳时效硬化的镍铜铬钼铌和镍铜锰钼铌合金钢压力容器板A737/A737M-99 高强度低合金钢压力容器板A738/A738M-00 中温和低温设备用经热处理的碳锰硅钢压力容器板A739-90a(2000) 升温或/和加压部件用热轧合金钢棒A740-98 钢丝网(编织或焊接电镀钢丝网)A741-98 公路护栏用镀锌钢丝绳和配件A742/A742M-98 波纹钢管用预涂聚合物和金属涂覆钢薄板A743/A743M-98ae1 一般用耐腐蚀铬铁及镍铬铁合金铸件A744/A744M-00 严酷条件下使用的耐腐蚀镍铬铁合金铸件A745/A745M-94(1999) 奥氏体钢锻件的超声波检验A746-99 排污管用球墨铸铁A747/A747M-99 沉淀硬化不锈钢铸件A748/A748M-87(1998) 压力容器用静态铸造的激冷白口铁-灰口铁双金属轧辊A749/A749M-97 热轧碳素钢和高强度低合金钢带材通用要求A74-98 铸铁污水管及配件的技术规范A750-77(1994)e1 阻挡区域用钢制通风格栅A751-96 钢制品化学分析的实验方法、操作和术语A752-93(1998) 合金钢条和粗圆钢丝A752M-93(1998) 合金钢条和粗圆钢丝(米制)A753-97 镍铁软磁合金A754/A754M-96(2000) X射线荧光涂层厚度的试验方法A755/A755M-99 外露建筑材料用热浸涂覆和用卷涂工艺预涂的钢薄板A756-94(2001) 耐磨不锈轴承钢A757/A757M-00 低温下承压设备及其它设备用铁素体和马氏体钢铸件A758/A758M-00 具有改进的切口韧性的对缝焊锻制碳素钢管配件A759-00 起重机用碳钢轨条A760/A760M-01 下水道和排水沟用金属涂覆的波纹钢管A761/A761M-98 现场栓接管、管拱和拱用波纹镀锌结构钢板A762/A762M-00 下水道和排水沟用预涂聚合物波纹钢管A763-93(1999)e1 铁素体不锈钢晶间腐蚀敏感性检测A764-95(2001) 机械弹簧用冷拉镀锌和按成品尺寸镀锌的碳素钢丝A765/A765M-98a 具有强制性韧性要求的碳素钢及低合金钢压力容器部件锻件A767/A767M-00b 钢筋混凝土用镀锌钢筋A768-95 涡轮机转子及轴用经真空处理的含铬12%的合金钢锻件A769/A769M-00 电阻焊钢结构型材A770/A770M-86(2001) 专用钢板通过厚度测量进行的抗拉试验A771/A771M-95(2001) 增殖反应堆堆芯部件用奥氏体不锈钢管A772/A772M-00 正弦电流用材料的交流磁导率的试验方法A773/A773M-96 用带直流电子的磁滞曲线记录仪的（B－H）回路法测量材料的磁性能的标准试验方法A774/A774M-00 低温和中温一般腐蚀情况下用的焊接锻制奥氏体不锈钢配件A775/A775M-01 涂环氧树脂的钢筋钢棒A778-01 焊接未退火的奥氏体不锈钢管形制品A779/A779M-00 预应力混凝土用应力消除未涂覆的密实七股钢丝绞绳A780-01 热浸镀锌层的损坏及无覆层区域的检修A781/A781M-00 一般工业用一般要求的钢和合金铸件A782/A782M-90(2001) 经淬火和回火的锰铬钼硅锆合金钢压力容器板A786/A786M-00b 轧制钢楼板A787-01 电阻焊金属涂覆碳素钢机械配管A788-98a 钢锻件A789/A789M-01 普通设备用无缝与焊接铁素体/奥氏体不锈钢管A790/A790M-01 无缝与焊接铁素体/奥氏体不锈钢管A792/A792M-99 热浸工艺法处理的55%铝-锌合金涂覆钢板A793-96 不锈钢轧制楼板A794-97 商品级冷轧碳素钢薄板(最高含碳量为0.16%-0.25%)A795-00 防火用黑色及热浸镀锌的焊接和无缝钢管A796/A796M-00 雨水管和卫生污水管及其它地下埋设管道用波纹钢管、管托架及拱形架结构设计惯例A798/A798M-01 下水道及其它类似用途用工厂制波纹钢管的安装A799/A799M-92(1997) 估算不锈钢铸件铁素体含量用仪表的校准A800/A800M-01 奥氏体合金钢铸件中铁素体含量的估算A801/A801M-99 铁钴高磁性饱和合金A802/A802M-95(2001) 钢铸件外观检验的表面验收标准A803/A803M-01 焊接铁素体不锈钢给水加热器管A804/A804M-99 在电力频率下用薄钢板型试样对材料交流磁特性的测试方法A805-93(1998) 冷轧碳素钢扁平线A807/A807M-97 下水道及其它类似用途用波纹结构钢涂覆管的安装A808/A808M-00a 具有改进的切口韧性的结构级高强度低合金碳钢、锰钢、铌钢和钒钢A809-98 镀铝碳素钢丝A810-00 镀锌钢管用绕网A811-97 粉末冶金技术制造的软磁铁零件A813/A813M-01 单或双焊接奥氏体不锈钢管A814/A814M-01 冷加工焊接奥氏体不锈钢管A815/A815M-01 锻制铁素体、铁素体/奥氏体和马氏体不锈钢管配件A817-00 链接栅栏网用金属涂覆钢丝A818-91(2001) 镀铜碳素钢丝A820-96 纤维增强混凝土用钢纤维A821/A821M-99 预应力混凝土容器用经回火的冷拉钢丝A822-90(2000) 液压系统设备用冷拉碳素无缝钢管A823-99 静铸永久铸模灰铸件A824-01 链接栅栏用Marcelled拉力金属涂覆钢丝A826/A826M-95(2001) 增殖反应堆堆芯部件用奥氏体和铁素体不锈钢管A827/A827M-93a(1998) 锻造及类似用途用的碳素钢板技术规范A829/A829M-00 结构性合金钢板A82-97ae1 钢筋混凝土用无节钢丝A830/A830M-00 按照化学成分要求提供的优质碳素钢板技术规范A831/A831M-95(2000) 核心部件用不锈耐热钢棒,坯段及锻件规格A832/A832M-99e1 压力容器板用铬钼钒及铬钼钒钛硼合金钢A833-84(1996) 用比较硬度测试仪测量金属材料的压痕硬性A834-95(2001) 一般工业用铁铸件的一般要求A835-84(2000) 铁合金与合金添加剂的筛分粒度A836/A836M-95b(2001) 搪瓷管和压力容器设备用钛稳定碳素体钢锻件A837-91(1996)e1 渗碳用合金钢锻件A838/A838M-97 继电器用易切削铁素体不锈软磁合金技术规范A839/A839M-96 软磁用途的磷铁粉末冶金制造的零件技术规范A840/A840M-00 全处理的磁性夹层钢A841/A841M-01 压力容器用温度机械控制工艺加工的钢板A842-85(1997) 高密度石墨铸铁A844/A844M-93(1999) 压力容器用直接淬火加工的含镍9%的合金钢板A845-85(2000) 用于脱氧与合金钢的钛碎片A846-85(2000) 用于脱氧与合金钢的铝碎片A847-99a 具有增强耐大气腐蚀性能的冷成型焊接与无缝高强度低合金结构管A848/A848M-96 低碳磁铁A849-00 波纹钢排水管和污水管用后涂覆铺面和衬里材料A851-96 高频感应焊接的未退火奥氏体钢冷凝器管A852/A852M-00a 最小屈服强度为70Ksi(485MPa),厚度为4英寸(100mm)的经淬火和回火的低合金结构钢板ASTM钢管标准4A853-93(1998) 普通碳素钢丝A854/A854M-98 镀锌高强度钢栅栏和格架用光滑金属线A855/A855M-98 锌-5%铝-铈合金涂覆的钢丝绳A856/A856M-98 锌-5%铝-铈合金涂覆的碳素钢丝A857/A857M-00a 冷成形轻型薄钢板桩A858/A858M-00 低温和腐蚀情况下用热处理碳素钢配件A859/A859M-95(1999) 压力容器部件用时效硬化镍铜铬钼钶低碳合金钢锻件A860/A860M-00 锻制高强度低合金钢的高强度对缝焊接配件A861-94e1 高硅铁管和配件A862/A862M-98 波纹钢污水管和排水管沥清(柏油)涂层的应用。

astm无缝钢管标准对照表

astm无缝钢管标准对照表ASTM无缝钢管标准对照表-钢管知识无缝钢管厂A1000-99 弹簧专用碳钢和合金钢钢丝规范A1001-99 大型材高强度钢铸件规范A1002-99 镍铝类合金铸件规范A100-93(2000) 硅铁A101-93(2000) 铬铁A102-93(2000) 钒铁合金A105/A105M-01 管系部件用碳素钢锻件A106-999e1 高温用无缝碳素钢管A108-99 优质冷加工碳素钢棒材技术规范A109/A109M-00e1 冷轧碳素钢带技术规范A111-99a 电话和电报线路用镀锌"铁"丝规格A116-00 镀锌钢丝编织栏栅网A121-99 镀锌刺钢丝A123/A123M-00 钢铁产品的锌镀层（热浸镀锌）技术规范A125-96 热处理螺旋形钢弹簧A126-95(2001) 阀门、法兰和管配件用灰铁铸件A128/A128M-93(1998) 钢铸件,奥氏体锰A131/A131M-94 海船用结构钢A132-89(2000) 钼铁合金A134-96 电熔(电弧)焊钢管(NPS为16英寸和16英寸以上)A135-01 电阻焊钢管A139-00 电熔(电弧)焊钢管(4英寸以上的)A143-74(1999) 热浸镀锌结构钢制品防脆裂措施和探测脆裂的程序A146-64(2000) 氧化钼制品A148/A148M-01 结构用高强度钢铸件A153/A153M-00 钢铁制金属构件上镀锌层(热浸)A159-83(2001) 汽车用灰铁铸件A167-99 不锈钢和耐热铬镍钢板、薄板及带材A176-99 不锈钢和耐热铬钢板、薄板及带材A178/A178M-95(2000) 电阻焊接碳素钢钢管及碳锰钢锅炉和过热器管的技术规范A179/A179M-90a(1996)e1 热交换器和冷凝器用无缝冷拉低碳钢管A181/A181M-01 普通锻制碳素钢管的规格A182/A182M-01 高温设备用锻制或轧制的合金钢管法兰、锻制管件、阀门及零件A183-98 钢轨用碳素钢螺栓和螺母A184/A184M-01 混凝土加筋用变形钢筋编织网A185-97 钢筋混凝土用焊接钢丝结构本文由钢管世界-无缝钢管提供：/转载注明出处!A1-00 碳素钢丁字轨A192/A192M-91(1996)e1 高压用无缝碳素钢锅炉管A193/A193M-01 高温设备用合金钢和不锈钢螺栓材料A194/A194M-01 高温和高压设备用碳素钢与合金钢螺栓和螺母的规格A197/A197M-00 化铁炉用可锻铸铁A20/A20M-01 压力容器用钢板材通用要求A202/A202M-93(1999) 压力容器用铬锰硅合金钢板A203/A203M-97 压力容器用镍合金钢板A204/A204M-93(1999) 压力容器用钼合金钢板A209/A209M-98 锅炉和过热器用无缝碳钼合金钢管A210/A210M-96 锅炉和过热器用无缝中碳素管A213/A213M-01 无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管A214/A214M-96 热交换器与冷凝器用电阻焊接碳素钢管A216/A216M-93(1998) 高温下使用的适合于熔焊的碳素钢铸件规格A217/A217M-01 适合高温受压零件用合金钢和马氏体不锈钢铸件A21-94(1999) 铁路用未经热处理和经热处理的碳素钢轴A220/A220M-99 珠光体可锻铁A225/A225M-93(1999) 压力容器用锰矾镍合金钢板A227/A227M-99 机械弹簧用冷拉钢丝A228/A228M-00 乐器用优质弹簧钢丝A229/A229M-99 机械弹簧用油回火的钢丝A230/A230M-99 阀门用油回火优质碳素钢弹簧丝A231/A231M-96 铬钒合金钢弹簧丝A232/A232M-99 阀门用优质铬钒合金钢弹簧丝A234/A234M-00a 中温与高温下使用的锻制碳素钢及合金钢管配件A239-95(1999) 用普力斯试验法(硫酸铜浸蚀)确定铁或钢制品上镀锌层最薄点的测试方法A240/A240M-01 压力容器用耐热铬及铬镍不锈钢板、薄板及带材A242/A242M-00a 高强度低合金结构钢A247-67(1998) 铁铸件中石墨显微结构评定试验方法A249/A249M-01 锅炉、过热器、换热器和冷凝器用焊接奥氏体钢管A250/A250M-95(2001) 锅炉和过热器用电阻焊铁素体合金钢管A252-98e1 焊接钢和无缝钢管桩A254-97 铜焊钢管规格A255-99 测定钢淬透性用末端淬火试验的标准试验方法A262-98 奥氏体不锈钢晶间浸蚀敏感性的检测A263-94a(1999) 耐腐蚀铬钢包覆板材,薄板材及带材技术规范A264-94a(1999) 包覆的不锈铬镍钢板,薄板及带材规格A265-94a(1999) 镍和镍基合金包覆钢板规格A266/A266M-99 压力容器部件用碳素钢锻件规格A268/A268M-01 一般设备用无缝和焊接铁素体与马氏体不锈钢管A269-01 一般设备用无缝和焊接奥氏体不锈钢管本文由钢管世界-无缝钢管提供：/转载注明出处!A27/A27M-95(2000) 通用碳素钢铸件A270-01 卫生设施用无缝钢和焊接奥氏体不锈钢管A275/A275M-98 钢锻件的磁粉检查试验方法A276-00a 不锈钢棒材和型材A278-93 适用于650F容压部件用灰铸铁件的技术规范A283/A283M-00 低和中等抗拉强度碳素钢板A285/A285M-90(2001) 压力容器用低和中等抗拉强度的碳素钢板A288-91(1998) 涡轮发电机磁性定位环用碳素钢和合金钢锻件A289/A289M-97 发电机非磁性定位环用合金钢锻件的技术规范A29/A29M-99e1 热锻及冷加工碳素钢和合金钢棒A2-90(1997) 普通型,带槽和防护型碳素工字钢轨A290-95(1999) 减速器环用碳素钢和合金钢锻件A291-95(1999) 减速器小齿轮、齿轮和心轴用碳素钢和合金钢锻件A295-98 高碳耐磨轴承钢技术规范A297/A297M-97(1998) 一般用耐热铬铁与镍铬铁合金钢铸件规格A299/A299M-97e1 压力容器用锰硅碳钢板A302/A302M-97e1 压力容器用锰钼和锰钼镍合金钢板A304-96 有末端淬火淬透性要求的合金钢棒材的技术规范A307-00 抗拉强度为60000psi的碳素钢螺栓和螺柱的技术规范A308-99 经热浸处理镀有铅锡合金的薄板材的技术规范A309-94a(1999) 用三点试验法测定长镀锌薄钢板镀层的重量成分的试验方法A311/A311M-95(2000) 有机械性能要求的消除应力的冷拉碳素钢棒A312/A312M-00c 无缝和焊接奥氏体不锈钢管A313/A313M-98 不锈钢弹簧丝技术规范A314-97 锻造用不锈及耐热钢坯及钢棒规格A31-00 钢铆钉及铆钉和压力容器用棒材A319-71(2001) 高温无压部件用灰铁铸件A320/A320M-01 低温用合金钢螺栓材料规格A321-90(1995)e1 经淬火和回火的碳素钢棒A322-91(1996) 合金钢棒材.级别A323-93(2000) 硼铁规格A324-73(2000) 钛铁合金A325-00 经热处理最小抗拉强度为120/105ksi的钢结构螺栓A325M-00 结构钢连接件用高强度螺栓(米制)A327-91(1997) 铸铁冲击试验方法A327M-91(1997) 铸铁冲击试验方法(米制)A328/A328M-00 薄钢板桩A331-95(2000) 冷加工合金钢棒A333/A333M-99 低温用无缝与焊接钢管规格A334/A334M-99 低温设备用无缝与焊接碳素和合金钢管A335/A335M-01 高温用无缝铁素体合金钢管A336/A336M-99e1 压力与高温部件用合金钢锻件规格本文由钢管世界-无缝钢管提供：/转载注明出处!A338-84(1998) 铁路,船舶和其他重型装备在温度达到650华氏度(345摄氏度)时使用的可锻铸铁法兰,管件和阀门零件A34/A34M-96 磁性材料的抽样和采购试验的标准惯例A340-99a 有关磁性试验用符号和定义的术语A341/A341M-00 用直流磁导计和冲击试验法测定材料的直流磁性能的试验方法A342/A342M-99 磁铁材料导磁率的试验方法A343-97 在电力频率下用瓦特计-安培计-伏特计法(100-1000赫兹)和25 厘米艾普斯亭(EPSTEIN) 机架测定材料的交流电磁性能的试验方法A345-98 磁设备用平轧电炉钢A348/A348M-00 用瓦特计--安培计--伏特计法(100-10000赫兹)和25厘米艾普斯亭框测定材料的交流磁性能的试验方法A350/A350M-00c 要求进行缺口韧性试验的管道部件用碳素钢与低合金钢锻件技术规范A351/A351M-00 容压零件用奥氏体及奥氏体铁素体铸铁的技术规范A352/A352M-93(1998) 低温受压零件用铁素体和马氏体钢铸件规格A353/A353M-93(1999) 压力容器用经二次正火及回火处理的含9％镍的合金钢板A354-01 淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格A355-89(2000) 渗氮用合金钢棒A356/A356M-98e1 蒸汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件A358/A358M-01 高温用电熔焊奥氏体铬镍合金钢管A36/A36M-00a 碳素结构钢技术规范A363-98 地面架空线用镀锌钢丝绳A367-60(1999) 铸铁的激冷试验方法A368-95a(2000) 不锈钢和耐热钢丝绳的标准A369/A369M-01 高温用锻制和镗孔碳素钢管和铁素体合金钢管A370-97a 钢制品机械测试的标准试验方法和定义A372/A372M-99 薄壁压力容器用碳素钢及合金钢锻件A376/A376M-01 高温中心站用无缝奥氏钢管A377-99 球墨铸铁压力管规范索引A380-99e1 不锈钢零件、设备和系统的清洗和除垢A381-96 高压输送用金属弧焊钢管A384-76(1996) 防止钢组件热浸镀锌时翘曲和扭曲用安全保护A385-00 提供高质量镀锌覆层(热浸)A3-01 低、中、高碳素钢鱼尾（连接）板A387/A387M-99e1 压力容器用铬钼合金钢板A388/A388M-95(2000)e1 重型钢锻件超声波检测A389/A389M-93(1998) 适合高温受压部件用经特殊热处理的合金钢铸件规格A390-95(2001) 饲养家禽用镀锌钢丝栏栅网(六角形和直线形)A391/A391M-98 80号合金钢链条A392-96 镀锌钢丝链环栏栅网A394-00 传动塔架用镀锌和裸露钢螺栓本文由钢管世界-无缝钢管提供：/转载注明出处!A395/A395M-99 高温用铁素体球墨铸铁受压铸件A400-69(2000) 钢棒的成分及机械性能选择指南A401/A401M-98 铬硅合金钢丝A403/A403M-00b 锻制奥氏体不锈钢管配件A407-93(1998) 盘簧用冷拉钢丝A409/A409M-01 腐蚀场所或高温下使用的焊接大口径奥氏体钢管A411-98 镀锌低碳钢铠装线A413/A413M-00 碳素钢链A414/A414M-00 压力容器用碳素薄钢板A416/A416M-99 预应力混凝土用无涂层七股钢铰线A417-93(1998) 之字型、方型和正弦型装垫弹簧元件用冷拉钢丝A418-99 涡轮机及发电机钢转子锻件的超声波检查方法A420/A420M-00b 低温下用锻制碳素钢和合金钢管配件A421/A421M-98a 预应力混凝土用无涂层消除应力钢丝的技术规范A423/A423M-95(2000) 无缝和电焊低合金钢管A424-00 搪瓷用钢薄板A426-92(1997) 高温用离心铸造的铁素体合金钢管A427-74(1996)e1 冷轧和热轧用锻制合金钢辊A428/A428M-01 钢铁制品上铝覆层重量的测试方法A434-90a(2000) 热轧与冷精轧经回火及淬火的合金钢棒A435/A435M-90(2001) 钢板的直射束纵向超声波检验A436-84(1997)e1 奥氏体灰口铁铸件A437/A437M-01 高温用经特殊处理的涡轮型合金钢螺栓材料A438-80(1997) 灰铸铁横向弯曲试验A439-83(1999) 奥氏体可锻铸铁铸件A447/A447M-93(1998) 高温用镍铬铁合金钢铸件(25-12级)A449-00 经淬火和回火的钢螺栓和螺柱A450/A450M-96a 碳素钢管、铁素体合金钢管及奥氏体合金钢管A451-93(1997) 高温用离心铸造的奥氏体钢管A453/A453M-00 具有同奥氏体钢相类似的膨胀系数、屈服强度为50-120Ksi(345-827MPa)的耐高温螺栓材料A455/A455M-90(2001) 压力容器用高强度碳锰钢板A456/A456M-99 大型曲轴锻件的磁粉检查A459-97 镀锌平轧扁钢铠装带A460-94(1999) 包铜钢丝绳标准A463/A463M-00 热浸镀铝薄钢板A466/A466M-98 非焊接碳素钢链A467/A467M-98 机器链和盘旋链A469-94a(1999) 用于发电机转子的真空处理钢锻件A470-01 涡轮机转子和轴用经真空处理的碳素钢和合金锻件A471-94(1999) 涡轮转子转盘和转轮用真空处理合金钢锻件技术规范A472-98 蒸汽涡轮机轴及转子锻件的热稳定性的试验方法本文由钢管世界-无缝钢管提供：/转载注明出处!A473-01 不锈和耐热钢锻件A474-98 包铝钢丝绳标准A475-98 镀锌钢丝绳A476/A476M-00 造纸厂干燥辊用球墨可锻铸铁件A478-97 铬镍不锈钢和耐热钢制编织钢丝A479/A479M-00 锅炉及压力容器用不锈钢和耐热钢棒与型材A47/A47M-99 铁素体可锻铁铸件A480/A480M-01 扁平轧制耐热不锈钢厚板材、薄板材和带材通用要求A481-94(2000) 金属铬A482-93(2000) 铬铁硅A483-64(2000) 硅锰合金A484/A484M-00 不锈及耐热锻钢棒,钢坯及锻件的规格A485-00 高淬透性耐磨轴承钢的技术规范A487/A487M-93(1998) 受压钢铸件A488/A488M-01 钢铸件焊接规程和工作人员的合格鉴定A48-94ae1 灰铁铸件A489-00 碳素钢吊耳A490-00 最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓A491-96 镀铝钢链环栏栅结构A492-95(2000) 耐热不锈钢丝绳A493-95(2000) 冷镦和冷锻不锈钢和耐热钢丝A494/A494M-00 镍和镍合金铸件A495-94(2000) 硅钙合金钢技术规范A496-97ae1 钢筋混凝土用变形钢丝A497-99e1 钢筋混凝土用焊接变形钢丝网A498-98 无缝与焊接碳素钢,铁素体钢与奥氏体钢制有整体散热片的换热器钢管A49-01 经热处理的碳素钢鱼尾（连接）板，微合金鱼尾板及锻制碳素钢异型鱼尾板A499-89(1997)e1 轧制丁字钢轨用的碳素钢棒材及型材的技术规范A500-01 圆形与异型焊接与无缝碳素钢结构管A501-01 热成型焊接与无缝碳素钢结构管A503/A503M-01 锻制大型曲轴的超声波检验A504-93(1999) 锻制碳素钢轮A505-00 热轧和冷轧合金钢薄板和带材A506-00 正规质量及优质结构的热轧和冷轧合金钢薄板与带材A507-00 优质拉拔,热轧和冷轧合金钢薄板与带材A508/A508M-95(1999) 压力容器用经回火和淬火真空处理的碳素钢与合金钢锻件A510-00 碳素钢盘条和粗圆钢丝通用要求A510M-00 碳素钢盘条和粗圆钢丝(米制)A511-96 无缝不锈钢机械管A512-96 冷拉对缝焊碳素钢机械管本文由钢管世界-无缝钢管提供：/转载注明出处!A513-00 电阻焊碳素钢与合金钢机械钢管A514/A514M-00a 焊接用经回火与淬火的高屈服强度合金钢板A515/A515M-92(1997) 中温及高温压力容器用碳素钢板A516/A516M-90(2001) 中温及低温压力容器用碳素钢板A517/A517M-93(1999) 压力容器用经回火与淬火的高强度合金钢板A518/A518M-99 耐蚀高硅铁铸件A519-96 无缝碳素钢与合金钢机械管A521-96 一般工业用闭式模钢锻件A522/A522M-95b(2000) 低温用锻制或轧制含镍8%和9%的合金钢法兰,配件,阀门和零件规格A523-96 高压管型电缆线路用平端无缝与电阻焊钢管A524-96 常温和低温用无缝碳素钢管A529/A529M-00 高强度碳锰结构钢质量A530/A530M-99e1 特种碳素钢和合金钢管A531/A531M-91(1996) 涡轮发电机钢定位环的超声波检验A532/A532M-93a(1999)e1 耐磨铸铁A533/A533M-93(1999) 压力容器用经回火和淬火的锰钼及锰钼镍合金钢板A534-94 用于耐摩擦轴承的渗碳钢A536-84(1999)e1 球墨铸铁件A537/A537M-95(2000) 压力容器用经热处理的碳锰硅钢板A53/A53M-01 无镀层热浸的、镀锌的、焊接的及无缝钢管的技术规范A539-99 天然气和燃料油管线用电阻焊钢盘管A540/A540M-00 特殊用途的合金钢螺栓材料A541/A541M-95(1999) 压力容器部件用经淬火和回火的碳素钢及合金钢锻件A542/A542M-99e1 压力容器用经回火和淬火的铬钼、铬钼钒及铬钼钒钛硼合金钢板A543/A543M-93(1999) 压力容器用经回火和淬火的镍铬钼合金钢板A550-78(2000) 铌铁合金A551-94(1999) 钢轮箍A553/A553M-95(2000) 压力容器用经回火和淬火的含8%及9%镍的合金钢板A554-98e1 焊接的无缝钢机械管A555/A555M-97 耐热不锈钢丝和盘条的通用要求A556/A556M-96 无缝冷拉碳素钢给水加热器管A560/A560M-93(1998) 铬镍合金铸件A561-71(1999) 工具钢棒的宏观刻蚀试验A562/A562M-90(2001) 搪玻璃或扩散金属镀层的压力容器用锰钛合金碳素钢板A563-00 碳合金钢螺母A563M-00 碳素钢及合金钢螺母技术规范（米制）A564/A564M-01 热轧及冷精轧时效硬化处理过的不锈钢棒材和型材技术规范A565-97 高温用马氏体不锈钢棒,锻件和锻制坯规格A568/A568M-00b 热轧及冷轧高强度低合金碳素钢薄板A571-84(1997) 适用于低温压力容器零件的奥氏体球墨铸铁件本文由钢管世界-无缝钢管提供：/转载注明出处!A571M-84(1997) 适用于低温压力容器零件的奥氏体球墨铸铁件(米制)A572/A572M-00a 高强度低合金钴钒结构钢技术规范A573/A573M-00a 增强韧性的结构碳素钢板A574-00 合金钢内六角螺钉A574M-00 合金钢内六角螺钉(米制)A575-96 商品级碳素钢棒(M级)A576-90b(2000) 特级热轧碳素钢棒A577/A577M-90(2001) 钢板的超声角波束检验A578/A578M-96(2001) 特殊设备用的普通钢板和包覆钢板的直波束超声探伤检验A579-99 超高强度合金钢锻件A580/A580M-98 耐热不锈钢丝A581/A581M-95b(2000) 高速切削用耐热不锈钢丝和盘条A582/A582M-95b(2000) 热轧或冷精轧的高速切削不锈及耐热钢棒A583-93(1999) 铁路用铸钢轮A584-97 镀铝钢丝编织栅栏网A585-97 镀铝刺钢丝A586-98 镀锌平行和螺旋形钢丝绳A587-96 化学工业用电阻焊低碳钢管A588/A588M-00a 高强度低合金结构钢4英寸(100mm)厚屈服点最小为50ksi(345MPa)A589-96 水井用无缝和焊接碳素钢管A591/A591M-98 薄镀层电解镀锌薄钢板A592/A592M-89(1999) 压力容器用经回火和淬火的高强度低合金钢锻制附件和零件A595-98 结构用圆锥形低碳钢管A596/A596M-95(1999) 用环形试验法和冲击法测定材料的直流磁性能的试验方法A597-87(1999) 铸造工具钢A598-92(1997) 磁放大器磁芯的磁性能测试法A599/A599M-99 锡制品，电解镀锡的冷滚轧薄板规范A6/A6M-01 轧制结构钢板材、型材和薄板桩通用技术要求A600-92a(1999) 高速工具钢A601-96(2000) 电解金属锰A602-94(1998) 汽车用可锻铸铁件A603-98 镀锌结构钢丝绳A604-93(1998) 自耗电极再溶化钢棒与钢坯的宏观腐蚀试验方法A606-98 改进防大气腐蚀性的热轧和冷轧高强度低合金钢薄板和带材A608-91a(1998) 高温受压离心铸造的铁铬镍高合金钢管A609/A609M-91(1997) 碳素钢,低合金钢和马氏体不锈钢铸件的超声波检测A853-93(1998) 普通碳素钢丝A854/A854M-98 镀锌高强度钢栅栏和格架用光滑金属线本文由钢管世界-无缝钢管提供：/转载注明出处!A855/A855M-98 锌-5%铝-铈合金涂覆的钢丝绳A856/A856M-98 锌-5%铝-铈合金涂覆的碳素钢丝A857/A857M-00a 冷成形轻型薄钢板桩A858/A858M-00 低温和腐蚀情况下用热处理碳素钢配件A859/A859M-95(1999) 压力容器部件用时效硬化镍铜铬钼钶低碳合金钢锻件A860/A860M-00 锻制高强度低合金钢的高强度对缝焊接配件A861-94e1 高硅铁管和配件A862/A862M-98 波纹钢污水管和排水管沥清(柏油)涂层的应用A865-97 钢管连接用黑色或镀锌焊接或无缝钢螺纹接头A866-94 耐磨中碳轴承钢A867/A867M-94(1998)e1 继电器用铁硅钢A871/A871M-00a 抗空气腐蚀的高强度低合金结构钢板A872-91(1997) 腐蚀环境下用离心铸造铁素体/奥氏体不锈钢管A874/A874M-98 适于低温使用的铁素体球墨铸铁铸件A875/A875M-01 热浸处理的锌-5%铝合金金属涂覆的钢薄板A876/A876M-98 全处理型平轧的晶粒取向的硅铁电工钢A877/A877M-99 铬硅合金阀弹簧级钢丝A878/A878M-99 经改良的铬钒阀弹簧级钢丝A879-00 每面镀层质量应予标明的电解镀锌薄钢板A880-95 评定钢、不锈钢及相关合金检验与测验组织和实验室的准则A881/A881M-99 预应力混凝土铁路轨枕用应力消除或应力松弛变形钢丝A882/A882M-96e1 涂环氧树脂的七股预应力钢丝绳A883-96 非金属磁性材料铁磁共振行距和旋磁比率的测试方法A884/A884M-01 钢筋用涂环氧树脂的钢丝与焊接钢丝织网的技术规范A885/A885M-96 波纹钢制下水沟、暗渠和雨水管用锌和聚芳基酰胺纤维复合涂覆钢板最新ASTM无缝钢管标准对照表-最全ASTM无缝钢管标准对照表-供应商ASTM无缝钢管标准对照表-国产ASTM无缝钢管标准对照表-国标钢管ASTM无缝钢管标准对照表-钢管厂ASTM无缝钢管标准对照表- 钢管大全ASTM无缝钢管标准对照表-ASTM无缝钢管标准对本文由钢管世界-无缝钢管提供：/转载注明出处!。

阀门材料

阀门材料标准代号：螺栓ASTM A193-螺母；ASTTM A194碳素钢铸件ASTM A216碳素钢锻件；ASTM A105铬钼钢铸件；ASTM A217铬钼钢锻件ASTM A182不锈钢铸件ASTM A351；不锈钢锻件;ASTM A182 低温碳钢铸件；ASTM A352丁晴橡胶（NBR）:-54~+120℃乙丙橡胶EPDM：-60~+150℃聚四氟乙烯PTFE：-200~+260℃氟橡胶VITON：-40~+230℃丁腈胶NBR(Nitrile Rubber) 由丙烯腈与丁二烯共聚合而成，由18%-50%，丙烯腈含量越高，对石化油品碳氢燃料油的抵抗性越好，但低温性能则变差，一般使用温度范围为-25～100℃。

丁腈胶为目前油封及O型圈最常用的橡胶材质之一。

优点：1.具有良好的抗油、抗水、抗溶剂及抗高压油的特性。

2.具良好的压缩变形，抗磨及伸长力。

缺点：不适合用于极性溶剂之中，例如酮类、臭氧、硝基烃、MEK和氯仿。

用于制作燃油箱，润滑油箱以及在石油系液压油、汽油、水、硅润滑脂、硅油、二酯系润滑油、甘醇系液压油等流体介质中使用的橡胶零件，特别是密封零件。

可说是目前用途最广、成本最低的橡胶密封件。

三元乙丙胶EPDM(Ethylene Propylene Rubber) 由乙烯及丙烯共聚合而成主链不合双链，因此耐热性、耐老化性、耐臭氧性、安定性均非常优秀，但无法硫磺加硫。

为解决此问题，在EP主链上导入少量有双链之第三成分而可硫磺加硫即成EPDM，一般使用温度范围为-50～150℃。

对极性溶剂如醇、酮、乙二醇及磷酸脂类液压油抵抗性极佳。

优点：1.具良好抗候性及抗臭氧性。

2.具极佳的抗水性及抗化学物。

3.可使用于醇类及酮类。

4.耐高温蒸气，对气体具良好的不渗透性。

缺点：不建议用于食品用途或是暴露于芳香氢之中。

1.高温水蒸汽环境之密封件。

2.卫浴设备密封件或零件。

3.制动（刹车）系统中的橡胶零件。

4.散热器（汽车水箱）中的密封件。

美国标准一览表

双法兰连接、凸耳及饼式蝶阀
API Std527-1991
泄压阀阀座的紧密度
API Std594-1997
饼式及饼式凸耳止回阀
API Std598-1996
阀的检验和试压
API Std600-2001
法兰和对焊连接的钢制闸阀
API Std603-2001
150级铸造耐腐蚀法兰端闸阀
API Std609-1997
API 593-81
法兰连接球墨铸铁旋塞阀（1）
API 594-91
对夹式和凸耳对夹式止回阀
API 595-79
法兰连接的铸铁闸阀（1）
API 597-81
法兰和对焊连接的钢制缩径闸阀（1）
API 598-94
阀门的检查和试验
API 599-94
法兰连接和焊连接的金属旋塞阀
API 600-91
法兰和对焊连接的钢制闸阀
避免氨装置中设备的环境开裂(第一版)
API Spcc6D-1994
管道阀门(闸阀旋塞阀球阀和止回阀)规范(第二十版)
API Spec 11V1-1995
气举阀、孔板、回流阀和隔板阀规范
API Spec 14A－2000第10版
井下安全阀设备规范
API Spec 598-96
阀门的检验和试验
API Spec 5L-2000
凸耳及饼式蝶阀
API Std620-1996
大型焊接低压储罐的设计和建造(第八版)
API Std674-1995
容积式泵-往复式(第一版)（英）
API Std674-1995
容积式泵-往复式(第一版)（中）
API Std675-1994
容积式泵-容积可控式(第一版)

美国ASTM标准

美国ASTM标准标准号中文名称英文名称A1-00碳素钢丁字轨Standard Specification for Carbon Steel Tee RailsA2-02普通型,带槽和防护型碳素工字钢轨Standard Specification for Carbon Steel Girder Rails of Plain, Grooved, and Guard TypesA3-01低、中、高碳素钢鱼尾（连接）板Standard Specification for Steel Joint Bars, Low, Medium, and High Carbon (Non-Heat-Treated)A6/A6M-04a轧制结构钢板材、型材和薄板桩通用技术要求Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling A20/A20M-04a压力容器用钢板材通用要求Standard Specification for General Requirements for Steel Plates for Pressure VesselsA27/A27M-03通用碳素钢铸件Standard Specification for Steel Castings, Carbon, for General ApplicationA29/A29M-04热锻及冷加工碳素钢和合金钢棒Standard Specification for Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements forA31-04钢铆钉及铆钉和压力容器用棒材Standard Specification for Steel Rivets and Bars for Rivets, Pressure VesselsA34/A34M-01磁性材料的抽样和采购试验的标准惯例Standard Practice for Sampling and Procurement Testing of Magnetic MaterialsA36/A36M-04碳素结构钢技术规范Standard Specification for Carbon Structural SteelA47/A47M-99铁素体可锻铁铸件Standard Specification forFerritic Malleable Iron Castings A48/A48M-03灰铁铸件Standard Specification for Gray Iron CastingsA49-01经热处理的碳素钢鱼尾（连接）板，微合金鱼尾板及锻制碳素钢异型鱼尾板Standard Specification for Heat-Treated Carbon Steel Joint Bars,Microalloyed Joint Bars, and Forged Carbon Steel Compromise Joint BarsA53/A53M-04无镀层热浸的、镀锌的、焊接的及无缝钢管的技术规范Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and SeamlessA65-01钢轨道钉Standard Specification for Steel Track Spikes A66-01钢质螺旋道钉Standard Specification for Steel Screw Spikes A67-00热加工低碳钢和高碳钢垫板技术规范Standard Specification for Steel Tie Plates, Low-Carbon and High-Carbon Hot-WorkedA74-04铸铁污水管及配件的技术规范Standard Specification for Cast Iron Soil Pipe and FittingsA82-02钢筋混凝土用无节钢丝Standard Specification for Steel Wire, Plain, for Concrete ReinforcementA90/A90M-01镀锌和镀锌合金钢铁制品镀层重量的试验方法Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy CoatingsA99-03锰铁合金Standard Specification for Ferromanganese A100-04硅铁Standard Specification for FerrosiliconA101-04铬铁Standard Specification for FerrochromiumA102-04钒铁合金Standard Specification for Ferrovanadium A105/A105M-03管系部件用碳素钢锻件Standard Specification for Carbon Steel Forgings for Piping ApplicationsA106/A106M-04a高温用无缝碳素钢管Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service A108-03优质冷加工碳素钢棒材技术规范Standard Specification for Steel Bar, Carbon and Alloy, Cold-Finished A109/A109M-03冷轧碳素钢带技术规范Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-RolledA111-99a(2004)e1电话和电报线路用镀锌"铁"丝规格Standard Specification for Zinc-Coated (Galvanized) Iron Telephone and Telegraph Line WireA116-00镀锌钢丝编织栏栅网Standard Specification for Metallic-Coated, Steel Woven Wire Fence Fabric A121-99(2004)镀锌刺钢丝Standard Specification for Mettalic-Coated Carbon Steel Barbed WireA123/A123M-02钢铁产品的锌镀层（热浸镀锌）技术规范Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsA125-96(2001)热处理螺旋形钢弹簧Standard Specification for Steel Springs, Helical, Heat-TreatedA126-04阀门、法兰和管配件用灰铁铸件Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe FittingsA128/A128M-93(2003)钢铸件,奥氏体锰Standard Specification for Steel Castings, Austenitic Manganese A131/A131M-04海船用结构钢Standard Specification for Structural Steel for ShipsA132-04钼铁合金Standard Specification for FerromolybdenumA134-96(2001)电熔(电弧)焊钢管(NPS为16英寸和16英寸以上)Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over)A135-01电阻焊钢管Standard Specification for Electric-Resistance-Welded Steel PipeA139/A139M-04电熔(电弧)焊钢管(4英寸以上的)Standard Specification for Electric-Fusion (Arc)-Welded Steel Pipe (NPS 4 and Over)A143/A143M-03热浸镀锌结构钢制品防脆裂措施和探测脆裂的程序Standard Practice for Safeguarding Against Embrittlement of Hot-Dip Galvanized Structural Steel Products and Procedure for Detecting EmbrittlementA144-02铁钨合金规范Specification for FerrotungstenA146-04氧化钼制品Standard Specification for Molybdenum Oxide ProductsA148/A148M-03结构用高强度钢铸件Standard Specification for Steel Castings, High Strength, for Structural Purposes A153/A153M-04钢铁制金属构件上镀锌层(热浸)Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel HardwareA159-83(2001)汽车用灰铁铸件Standard Specification for Automotive Gray Iron CastingsA167-99不锈钢和耐热铬镍钢板、薄板及带材Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and StripA176-99不锈钢和耐热铬钢板、薄板及带材Standard Specification for Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and StripA178/A178M-02电阻焊接碳素钢钢管及碳锰钢锅炉和过热器管的技术规范Standard Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater TubesA179/A179M-90a(2001)热交换器和冷凝器用无缝冷拉低碳钢管Standard Specification for Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser TubesA181/A181M-01普通锻制碳素钢管的规格Standard Specification for Carbon Steel Forgings, for General-Purpose PipingA182/A182M-02高温设备用锻制或轧制的合金钢管法兰、锻制管件、阀门及零件Standard Specification for Forged or Rolled Alloy-Steel Pipe Flanges,Forged Fittings, and Valves and Parts for High-Temperature ServiceA183-03钢轨用碳素钢螺栓和螺母Standard Specification for Carbon Steel Track Bolts and NutsA184/A184M-01混凝土加筋用变形钢筋编织网Standard Specification for Fabricated Deformed Steel Bar Mats for Concrete ReinforcementA185-02钢筋混凝土用焊接钢丝结构Standard Specification for Steel Welded Wire Reinforcement, Plain, for Concrete A192/A192M-02高压用无缝碳素钢锅炉管Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure ServiceA193/A193M-04b高温设备用合金钢和不锈钢螺栓材料Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature ServiceA194/A194M-04a高温和高压设备用碳素钢与合金钢螺栓和螺母的规格Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both A197/A197M-00化铁炉用可锻铸铁Standard Specification forCupola Malleable IronA202/A202M-03压力容器用铬锰硅合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Manganese-SiliconA203/A203M-97(2003)压力容器用镍合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel A204/A204M-03压力容器用钼合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, Molybdenum A209/A209M-03锅炉和过热器用无缝碳钼合金钢管Standard Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater TubesA210/A210M-02锅炉和过热器用无缝中碳素管Standard Specification for Seamless Medium-Carbon Steel Boiler and Superheater TubesA213/A213M-04无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes A214/A214M-96(2001)热交换器与冷凝器用电阻焊接碳素钢管Standard Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser TubesA216/A216M-93(2003)高温下使用的适合于熔焊的碳素钢铸件规格Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High- Temperature ServiceA217/A217M-02适合高温受压零件用合金钢和马氏体不锈钢铸件Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature ServiceA220/A220M-99珠光体可锻铁Standard Specification for Pearlitic Malleable IronA225/A225M-03压力容器用锰矾镍合金钢板StandardSpecification for Pressure Vessel Plates, Alloy Steel, Manganese-Vanadium-NickelA227/A227M-99机械弹簧用冷拉钢丝Standard Specification for Steel Wire, Cold-Drawn for Mechanical Springs A228/A228M-02乐器用优质弹簧钢丝Standard Specification for Steel Wire, Music Spring QualityA229/A229M-99机械弹簧用油回火的钢丝Standard Specification for Steel Wire, Oil-Tempered for Mechanical Springs A230/A230M-99阀门用油回火优质碳素钢弹簧丝Standard Specification for Steel Wire, Oil-Tempered Carbon Valve Spring QualityA231/A231M-96(2002)铬钒合金钢弹簧丝Standard Specification for Chromium-Vanadium Alloy Steel Spring Wire A232/A232M-99阀门用优质铬钒合金钢弹簧丝Standard Specification for Chromium-Vanadium Alloy Steel Valve Spring Quality WireA234/A234M-04中温与高温下使用的锻制碳素钢及合金钢管配件Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service A239-95(2004)用普力斯试验法(硫酸铜浸蚀)确定铁或钢制品上镀锌层最薄点的测试方法Standard Practice for Locating the Thinnest Spot in a Zinc (Galvanized)Coating on Iron or Steel ArticlesA240/A240M-04ae1压力容器用耐热铬及铬镍不锈钢板、薄板及带材Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General ApplicationsA242/A242M-04高强度低合金结构钢Standard Specificationfor High-Strength Low-Alloy Structural SteelA247-67(1998)铁铸件中石墨显微结构评定试验方法Standard Test Method for Evaluating the Microstructure of Graphite in Iron CastingsA249/A249M-04锅炉、过热器、换热器和冷凝器用焊接奥氏体钢管Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser TubesA250/A250M-04锅炉和过热器用电阻焊铁素体合金钢管Standard Specification for Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and Superheater TubesA252-98(2002)焊接钢和无缝钢管桩Standard Specification for Welded and Seamless Steel Pipe Piles A254-97(2002)铜焊钢管规格Standard Specification for Copper-Brazed Steel Tubing A255-02测定钢淬透性用末端淬火试验的标准试验方法Standard Test Method for Determining Hardenability of SteelA262-03奥氏体不锈钢晶间浸蚀敏感性的检测Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless SteelsA263-03耐腐蚀铬钢包覆板材,薄板材及带材技术规范Standard Specification for Stainless Chromium Steel-Clad Plate A264-03包覆的不锈铬镍钢板,薄板及带材规格Specification for Stainless Chromium-Nickel Steel-Clad PlateA265-03镍和镍基合金包覆钢板规格Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel PlateA266/A266M-03a压力容器部件用碳素钢锻件规格Standard Specification for Carbon Steel Forgings for Pressure Vessel ComponentsA268/A268M-04一般设备用无缝和焊接铁素体与马氏体不锈钢管Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General ServiceA269-04一般设备用无缝和焊接奥氏体不锈钢管Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General ServiceA270-03a卫生设施用无缝钢和焊接奥氏体不锈钢管Standard Specification for Seamless and Welded Austenitic Stainless Steel Sanitary TubingA275/A275M-98(2003)钢锻件的磁粉检查试验方法Standard Test Method for Magnetic Particle Examination of Steel Forgings A276-04不锈钢棒材和型材Standard Specification for Stainless Steel Bars and ShapesA278/A278M-01适用于650F容压部件用灰铸铁件的技术规范Standard Specification for Gray Iron Castings for Pressure-Containing Parts for Temperatures Up to 650°F (350°C) A283/A283M-03低和中等抗拉强度碳素钢板Standard Specification for Low and Intermediate Tensile Strength Carbon Steel PlatesA285/A285M-03压力容器用低和中等抗拉强度的碳素钢板Intermediate-Tensile StrengthA288-91(2003)涡轮发电机磁性定位环用碳素钢和合金钢锻件Standard Specification for Carbon and Alloy Steel Forgings for Magnetic Retaining Rings for Turbine GeneratorsA289/A289M-97(2003)发电机非磁性定位环用合金钢锻件的技术规范Standard Specification for Alloy Steel Forgings for Nonmagnetic Retaining Rings for GeneratorsA290-02减速器环用碳素钢和合金钢锻件Standard Specification for Carbon and Alloy Steel Forgings for Rings for Reduction GearsA291-03减速器小齿轮、齿轮和心轴用碳素钢和合金钢锻件Standard Specification for Steel Forgings, Carbon and Alloy, for Pinions, Gears and Shafts for Reduction GearsA295-98高碳耐磨轴承钢技术规范Standard Specification for High-Carbon Anti-Friction Bearing SteelA297/A297M-97(2003)一般用耐热铬铁与镍铬铁合金钢铸件规格Standard Specification for Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat Resistant, for General Application A299/A299M-04压力容器用锰硅碳钢板Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-SiliconA302/A302M-03压力容器用锰钼和锰钼镍合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-NickelA304-04有末端淬火淬透性要求的合金钢棒材的技术规范Standard Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability RequirementsA307-04抗拉强度为60000psi的碳素钢螺栓和螺柱的技术规范Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile StrengthA308/A308M-03经热浸处理镀有铅锡合金的薄板材的技术规范Standard Specification for Steel Sheet, Terne (Lead-Tin Alloy) Coated by the Hot-Dip ProcessA309-01用三点试验法测定长镀锌薄钢板镀层的重量成分的试验方法Standard Test Method for Weight and Composition of Coating on Terne Sheet by the Triple-Spot TestA311/A311M-04有机械性能要求的消除应力的冷拉碳素钢棒Standard Specification for Cold-Drawn, Stress-Relieved Carbon Steel Bars Subject to Mechanical Property Requirements A312/A312M-04a无缝和焊接奥氏体不锈钢管Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel PipesA313/A313M-03不锈钢弹簧丝技术规范StandardSpecification for Stainless Steel Spring WireA314-97(2002)锻造用不锈及耐热钢坯及钢棒规格Standard Specification for Stainless Steel Billets and Bars for Forging A319-71(2001)高温无压部件用灰铁铸件Standard Specification for Gray Iron Castings for Elevated Temperatures for Non-Pressure Containing PartsA320/A320M-04低温用合金钢螺栓材料规格Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for Low-T emperature ServiceA321-90(2001)经淬火和回火的碳素钢棒Standard Specification for Steel Bars, Carbon, Quenched and T empered A322-91(2001)e1合金钢棒材.级别Standard Specification for Steel Bars, Alloy, Standard GradesA323-93(2000)硼铁规格Standard Specification for FerroboronA324-73(2000)钛铁合金Standard Specification for FerrotitaniumA325-04a经热处理最小抗拉强度为120/105ksi的热处理钢结构螺栓Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile StrengthA325M-04a经热处理最小抗拉强度为830Mpa的热处理钢结构螺栓Minimum Tensile Strength [Metric]A327-91(1997)铸铁冲击试验方法Standard Test Methods for Impact Testing of Cast IronsA327M-91(1997)铸铁冲击试验方法(米制)Standard Test Methods for Impact Testing of Cast Irons (Metric) A328/A328M-03薄钢板桩Standard Specification for Steel Sheet Piling A333/A333M-04a低温用无缝与焊接钢管规格Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature ServiceA334/A334M-04a低温设备用无缝与焊接碳素和合金钢管Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-T emperature ServiceA335/A335M-03高温用无缝铁素体合金钢管Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature ServiceA336/A336M-03a压力与高温部件用合金钢锻件规格Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature PartsA338-84(2004)铁路,船舶和其他重型装备在温度达到650华氏度(345摄氏度)时使用的可锻铸铁法兰,管件和阀门零件Standard Specification for Malleable Iron Flanges, Pipe Fittings, andValve Parts for Railroad, Marine, and Other Heavy Duty Service atTemperatures Up to 650°F (345°C)A340-03a有关磁性试验用符号和定义的术语Standard Terminology of Symbols and Definitions Relating to Magnetic TestingA341/A341M-00用直流磁导计和冲击试验法测定材料的直流磁性能的试验方法Standard Test Method for Direct Current Magnetic Properties of MaterialsUsing D-C Permeameters and the Ballistic Test MethodsA342/A342M-99磁铁材料导磁率的试验方法Standard Test Methods for Permeability of Feebly Magnetic Materials A343/A343M-03在电力频率下用瓦特计-安培计-伏特计法(100-1000赫兹)和25 厘米艾普斯亭(EPSTEIN) 机架测定材料的交流电磁性能的试验方法Standard Test Method for Alternating-Current Magnetic Properties ofMaterials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Methodand 25-cm Epstein Test FrameA345-98磁设备用平轧电炉钢Standard Specification for Flat-Rolled Electrical Steels for Magnetic ApplicationsA348/A348M-00用瓦特计--安培计--伏特计法(100-10000赫兹)和25厘米艾普斯亭框测定材料的交流磁性能的试验方法Standard Test Method for Alternating Current Magnetic Properties ofMaterials Using the Wattmeter-Ammeter-Voltmeter Method, 100 to 10 000 Hzand 25-cm Epstein FrameA350/A350M-04要求进行缺口韧性试验的管道部件用碳素钢与低合金钢锻件技术规范Standard Specification for Carbon and Low-Alloy Steel Forgings, RequiringNotch Toughness T esting for Piping ComponentsA351/A351M-03容压零件用奥氏体及奥氏体铁素体铸铁的技术规范Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing PartsA352/A352M-03低温受压零件用铁素体和马氏体钢铸件规格Standard Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing Parts, Suitable for Low-Temperature ServiceA353/A353M-93(1999)压力容器用经二次正火及回火处理的含9％镍的合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel, Double-Normalized and Tempered A354-04淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded FastenersA355-89(2000)渗氮用合金钢棒Standard Specification for Steel Bars, Alloys, for NitridingStandard Specification for Steel Castings, Carbon, Low Alloy, andA356/A356M-98(2003)蒸汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件Stainless Steel, Heavy-Walled for Steam Turbines A358/A358M-04高温用电熔焊奥氏体铬镍合金钢管Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General ApplicationsA363-03地面架空线用镀锌钢丝绳Standard Specification for Zinc-Coated (Galvanized) Steel Overhead Ground Wire Strand A367-60(1999)铸铁的激冷试验方法Standard Test Methods of Chill Testing of Cast IronA368-95a(2000)不锈钢和耐热钢丝绳的标准Standard Specification for Stainless Steel Wire StrandA369/A369M-02高温用锻制和镗孔碳素钢管和铁素体合金钢管Standard Specification for Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature ServiceA370-03a钢制品机械测试的标准试验方法和定义Standard Test Methods and Definitions for Mechanical Testing of Steel Products A372/A372M-03薄壁压力容器用碳素钢及合金钢锻件Standard Specification for Carbon and Alloy Steel Forgings for Thin-Walled Pressure VesselsA376/A376M-02a高温中心站用无缝奥氏钢管Standard Specification for Seamless Austenitic Steel Pipe for High-Temperature Central-Station ServiceA377-03球墨铸铁压力管规范索引Standard Index of Specifications for Ductile-Iron Pressure PipeA380-99e1不锈钢零件、设备和系统的清洗和除垢Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and SystemsA381-96(2001)高压输送用金属弧焊钢管Standard Specification for Metal-Arc-Welded Steel Pipe for Use With High-Pressure Transmission SystemsA384/A384M-02防止钢组件热浸镀锌时翘曲和扭曲用安全保护Standard Practice for Safeguarding Against Warpage and Distortion During Hot-Dip Galvanizing of Steel Assemblies A385-03提供高质量镀锌覆层(热浸)Standard Practice for Providing High-Quality Zinc Coatings (Hot-Dip)A387/A387M-03压力容器用铬钼合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-MolybdenumA388/A388M-03重型钢锻件超声波检测Standard Practice for Ultrasonic Examination of Heavy Steel ForgingsA389/A389M-03适合高温受压部件用经特殊热处理的合金钢铸件规格Standard Specification for Steel Castings, Alloy, Specially Heat-Treated, for Pressure-Containing Parts, Suitable for High-Temperature ServiceA390-95(2001)饲养家禽用镀锌钢丝栏栅网(六角形和直线形)Standard Specification for Zinc-Coated (Galvanized) Steel Poultry Fence Fabric (Hexagonal and Straight Line)A391/A391M-0180号合金钢链条Standard Specification for Grade 80 Alloy Steel ChainA392-03镀锌钢丝链环栏栅网Standard Specification for Zinc-Coated Steel Chain-Link Fence FabricA394-04传动塔架用镀锌和裸露钢螺栓Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare A395/A395M-99e1高温用铁素体球墨铸铁受压铸件Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated TemperaturesA400-69(2000)钢棒的成分及机械性能选择指南Standard Practice for Steel Bars, Selection Guide, Composition, and Mechanical PropertiesA401/A401M-03铬硅合金钢丝Standard Specification for Steel Wire, Chromium-Silicon AlloyA403/A403M-04锻制奥氏体不锈钢管配件Standard Specification for Wrought Austenitic Stainless Steel Piping FittingsA407-93(2004)盘簧用冷拉钢丝Standard Specification for Steel Wire, Cold-Drawn, for Coiled-Type SpringsA409/A409M-01腐蚀场所或高温下使用的焊接大口径奥氏体钢管Standard Specification for Welded Large Diameter Austenitic Steel Pipe for Corrosive or High-T emperature Service A411-03镀锌低碳钢铠装线Standard Specification for Zinc-Coated (Galvanized) Low-Carbon Steel Armor WireA413/A413M-01碳素钢链Standard Specification for Carbon Steel ChainA414/A414M-04压力容器用碳素薄钢板Standard Specification for Steel, Sheet, Carbon, for Pressure Vessels A416/A416M-02预应力混凝土用无涂层七股钢铰线Standard Specification for Steel Strand, Uncoated Seven-Wire for Prestressed ConcreteA417-93(2004)之字形、方形、正弦形家具用弹簧元件用冷拔钢丝Standard Specification for Steel Wire, Cold-Drawn, for Zig-Zag, Square-Formed, and Sinuous-Type Upholstery Spring Units A418-99(2003)涡轮机及发电机钢转子锻件的超声波检查方法Standard Test Method for Ultrasonic Examination of Turbine and Generator Steel Rotor ForgingsA420/A420M-04低温下用锻制碳素钢和合金钢管配件Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature ServiceA421/A421M-02预应力混凝土用无涂层消除应力钢丝的技术规范Standard Specification for Uncoated Stress-Relieved Steel Wire for Prestressed ConcreteA423/A423M-95(2000)无缝和电焊低合金钢管Standard Specification for Seamless and Electric-Welded Low-Alloy Steel TubesA424-00搪瓷用钢薄板Standard Specification for Steel, Sheet, for Porcelain EnamelingA426/A426M-02高温用离心铸造的铁素体合金钢管Standard Specification for Centrifugally Cast Ferritic Alloy Steel Pipe for High-Temperature ServiceA427-02冷轧和热轧用锻制合金钢辊Standard Specification for Wrought Alloy Steel Rolls for Cold and Hot Reduction A428/A428M-01钢铁制品上铝覆层重量的测试方法Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel ArticlesA434-04热轧与冷精轧经回火及淬火的合金钢棒Standard Specification for Steel Bars, Alloy, Hot-Wrought or Cold-Finished, Quenched and TemperedA435/A435M-90(2001)钢板的直射束纵向超声波检验Standard Specification for Straight-Beam Ultrasonic Examination of Steel PlatesA436-84(2001)奥氏体灰口铁铸件Standard Specification for Austenitic Gray Iron CastingsA437/A437M-01a高温用经特殊处理的涡轮型合金钢螺栓材料Standard Specification for Alloy-Steel Turbine-Type Bolting Material Specially Heat Treated for High-Temperature Service A439-83(1999)奥氏体可锻铸铁铸件Standard Specification for Austenitic Ductile Iron CastingsA447/A447M-93(2003)高温用镍铬铁合金钢铸件(25-12级)Standard Specification for Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service A449-04a经淬火和回火的钢螺栓和螺柱Standard Specification for Quenched and Tempered Steel Bolts and StudsStandard Specification for General Requirements for Carbon, FerriticA450/A450M-04碳素钢管、铁素体合金钢管及奥氏体合金钢管Alloy, and Austenitic Alloy Steel TubesA451/A451M-02高温用离心铸造的奥氏体钢管Standard Specification for Centrifugally Cast Austenitic Steel Pipe for High-Temperature ServiceA453/A453M-03具有同奥氏体钢相类似的膨胀系数、屈服强度为50-120Ksi(345-827MPa)的耐高温螺栓材料Standard Specification for High-Temperature Bolting Materials, withExpansion Coefficients Comparable to Austenitic Stainless SteelsA455/A455M-03压力容器用高强度碳锰钢板Standard Specification for Pressure Vessel Plates, Carbon Steel, High-Strength ManganeseA456/A456M-99(2003)大型曲轴锻件的磁粉检查StandardSpecification for Magnetic Particle Examination of Large Crankshaft ForgingsA459-97(2003)镀锌平轧扁钢铠装带Standard Specification for Zinc-Coated Flat Steel Armoring Tape A460-94(2004)e1包铜钢丝绳标准Standard Specification for Copper-Clad Steel Wire Strand A463/A463M-02a热浸镀铝薄钢板Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process A466/A466M-01非焊接碳素钢链Standard Specification for Weldless ChainA467/A467M-01机器链和盘旋链Standard Specification for Machine and Coil ChainA469-04用于发电机转子的真空处理钢锻件Standard Specification for Vacuum-Treated Steel Forgings for Generator RotorsA470-03涡轮机转子和轴用经真空处理的碳素钢和合金锻件Standard Specification for Vacuum-Treated Carbon and Alloy Steel Forgings for Turbine Rotors and ShaftsA471-02涡轮转子转盘和转轮用真空处理合金钢锻件技术规范Standard Specification for Vacuum-Treated Alloy Steel Forgings for Turbine Rotor Disks and WheelsA472-98(2003)蒸汽涡轮机轴及转子锻件的热稳定性的试验方法Standard Test Method for Heat Stability of Steam Turbine Shafts and Rotor ForgingsA473-01不锈和耐热钢锻件Standard Specification for Stainless Steel ForgingsA474-03包铝钢丝绳标准Standard Specification for Aluminum-Coated Steel Wire Strand A475-03镀锌钢丝绳Standard Specification for Zinc-Coated Steel Wire Strand A476/A476M-00造纸厂干燥辊用球墨可锻铸铁件Standard Specification for Ductile Iron Castings for Paper Mill Dryer RollsA478-97(2002)铬镍不锈钢和耐热钢制编织钢丝Standard Specification for Chromium-Nickel Stainless Steel Weaving and Knitting WireA479/A479M-04锅炉及压力容器用不锈钢和耐热钢棒与型材Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure VesselsA480/A480M-04扁平轧制耐热不锈钢厚板材、薄板材和带材通用要求Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip A481-94(2000)金属铬Standard Specification for Chromium MetalA482-93(2000)铬铁硅Standard Specification for Ferrochrome-Silicon A483-64(2000)硅锰合金Standard Specification for SilicomanganeseA484/A484M-03a不锈及耐热锻钢棒,钢坯及锻件的规格Standard Specification for General Requirements for Stainless Steel Bars, Billets, and ForgingsA485-03高淬透性耐磨轴承钢的技术规范Standard Specification for High Hardenability Antifriction Bearing Steel A487/A487M-93(1998)受压钢铸件Standard Specification for Steel Castings Suitable for Pressure ServiceA488/A488M-01e1钢铸件焊接规程和工作人员的合格鉴定Standard Practice for Steel Castings, Welding, Qualifications of Procedures and PersonnelA489-04碳素钢吊耳Standard Specification for Carbon Steel Lifting EyesA490M-04a最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile StrengthA490-04a最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints [Metric]A491-03镀铝钢链环栏栅结构Standard Specification for Aluminum-Coated Steel Chain-Link Fence Fabric A492-95(2000)耐热不锈钢丝绳Standard Specification for Stainless Steel Rope WireA493-95(2000)冷镦和冷锻不锈钢和耐热钢丝Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold ForgingA494/A494M-03ae1镍和镍合金铸件Standard Specification for Castings, Nickel and Nickel Alloy A495-94(2000)硅钙合金钢技术规范Standard Specification for Calcium-Silicon Alloys A496-02钢筋混凝土用变形钢丝Standard Specification for Steel Wire, Deformed, for Concrete ReinforcementA497/A497M-02钢筋混凝土用焊接变形钢丝网Standard Specification for Steel Welded Wire Reinforcement, Deformed, for ConcreteA498-04无缝与焊接碳素钢,铁素体钢与奥氏体钢制有整体散热片的换热器钢管Standard Specification for Seamless and Welded Carbon Steel Heat-Exchanger Tubes with Integral FinsA499-89(2002)轧制丁字钢轨用的碳素钢棒材及型材的技术规范Standard Specification for Steel Bars and Shapes, Carbon Rolled from T RailsA500-03a圆形与异型焊接与无缝碳素钢结构管Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and ShapesA501-01热成型焊接与无缝碳素钢结构管StandardSpecification for Hot-Formed Welded and Seamless Carbon Steel Structural TubingA502-03结构钢铆钉规范Standard Specification for Rivets, Steel, StructuralA503/A503M-01(2001)e1锻制大型曲轴的超声波检验Standard Specification for Ultrasonic Examination of Forged Crankshafts A504-04e1锻制碳素钢轮Standard Specification for Wrought Carbon Steel Wheels A505-00热轧和冷轧合金钢薄板和带材Standard Specification for Steel, Sheet and Strip, Alloy, Hot-Rolled and Cold-Rolled, General Requirements forA506-04正规质量及优质结构的热轧和冷轧合金钢薄板与带材Standard Specification for Alloy and Structural Alloy Steel, Sheet and Strip, Hot-Rolled and Cold-RolledA507-04优质拉拔,热轧和冷轧合金钢薄板与带材Standard Specification for Drawing Alloy Steel, Sheet and Strip, Hot-Rolled and Cold-RolledA508/A508M-04b压力容器用经回火和淬火真空处理的碳素钢与合金钢锻件Standard Specification for Quenched and T empered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure VesselsA510-03碳素钢盘条和粗圆钢丝通用要求Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon SteelStandard Specification for General Requirements for Wire Rods and CoarseA510M-03碳素钢盘条和粗圆钢丝通用要求Round Wire, Carbon Steel [Metric]A511-04无缝不锈钢机械管Standard Specification for Seamless Stainless Steel Mechanical TubingA512-96(2001)冷拉对缝焊碳素钢机械管Standard Specification for Cold-Drawn Buttweld Carbon Steel Mechanical TubingA513-00电阻焊碳素钢与合金钢机械钢管Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical TubingA514/A514M-00a焊接用经回火与淬火的高屈服强度合金钢板Standard Specification for High-Yield-Strength, Quenched and Tempered Alloy Steel Plate, Suitable for WeldingA515/A515M-03中温及高温压力容器用碳素钢板Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature ServiceA516/A516M-04中温及低温压力容器用碳素钢板Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature ServiceA517/A517M-93(1999)压力容器用经回火与淬火的高强度合金钢板Standard Specification for Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and TemperedA518/A518M-99(2003)耐蚀高硅铁铸件Standard Specification for Corrosion-Resistant High-Silicon Iron CastingsA519-03无缝碳素钢与合金钢机械管Standard Specification for Seamless Carbon and Alloy Steel Mechanical TubingA521-03一般工业用闭式模钢锻件Standard Specification for Steel, Closed-Impression Die Forgings for General Industrial Use A522/A522M-01低温用锻制或轧制含镍8%和9%的合金钢法兰,配件,阀门和零件规格Standard Specification for Forged or Rolled 8 and 9% Nickel Alloy SteelFlanges, Fittings, Valves, and Parts for Low-T emperature。

终版采油井口技术规格书5.5

①额定工作压力级别：105MPa；
②材料级别：EE级；
③产品规范级别：PSL3；
④产品性能级别：PR1；
⑤温度级别：P.U(-29℃～+121℃)。
6.部分零件选材及要求
6.1平板阀均采用明杆结构，可以观察阀门的开关状态。
6.2平板阀阀板和阀座本体采用不锈钢材料锻造成型，阀板阀座的密封表面喷焊硬质合金。密封
中国石油化工股份有限公司东北油气分公司
技术规格书
井口装置和采油树采购文件
项目编号：
文件编号：
版本：A/0
修订日期：2014.04.20
实施日期：2014.04.20
页码：1／11
目次
1. 适用范围...................................................................... 2
编制/日期：
校对/日期：
审定/日期：
中国石油化工股份有限公司东北油气分公司
技术规格书
井口装置和采油树采购文件
项目编号：
文件编号：
版本：A/0
修订日期：2014.04.20
实施日期：2014.04.20
页码：2／11
1.适用范围
本技术规格书规定了东北油气分公司石油、天然气勘探开发过程中所需井口装置和采油树的设计、材料、制造、检验和试验的最低要求。
2.8产品的设计制造验收应符合ISO TS 29001《石油、化工和天然气工业质量纲要规范》；API Q1第8版《石油、石化和天然气行业质量纲要规范》；GB/T 19001-2008 IDT ISO9001:2008《质量管理体系要求》的规定。
3.供货商要求
3.1 供货商应通过ISO9000 质量体系认证或与之等效的质量体系认证，以及HSE 体系认证，证书必须在有效期内。

ASTM钢管标准

ASTM钢管标准A1000-99 弹簧专用碳钢和合金钢钢丝规范A1001-99 大型材高强度钢铸件规范A1002-99 镍铝类合金铸件规范A100-93(2000) 硅铁A101-93(2000) 铬铁A102-93(2000) 钒铁合金A105/A105M-01 管系部件用碳素钢锻件A106-999e1 高温用无缝碳素钢管A108-99 优质冷加工碳素钢棒材技术规范A109/A109M-00e1 冷轧碳素钢带技术规范A111-99a 电话和电报线路用镀锌"铁"丝规格A116-00 镀锌钢丝编织栏栅网A121-99 镀锌刺钢丝A123/A123M-00 钢铁产品的锌镀层（热浸镀锌）技术规范A125-96 热处理螺旋形钢弹簧A126-95(2001) 阀门、法兰和管配件用灰铁铸件A128/A128M-93(1998) 钢铸件,奥氏体锰A131/A131M-94 海船用结构钢A132-89(2000) 钼铁合金A134-96 电熔(电弧)焊钢管(NPS为16英寸和16英寸以上)A135-01 电阻焊钢管A139-00 电熔(电弧)焊钢管(4英寸以上的)A143-74(1999) 热浸镀锌结构钢制品防脆裂措施和探测脆裂的程序A146-64(2000) 氧化钼制品A148/A148M-01 结构用高强度钢铸件A153/A153M-00 钢铁制金属构件上镀锌层(热浸)A159-83(2001) 汽车用灰铁铸件A167-99 不锈钢和耐热铬镍钢板、薄板及带材A176-99 不锈钢和耐热铬钢板、薄板及带材A178/A178M-95(2000) 电阻焊接碳素钢钢管及碳锰钢锅炉和过热器管的技术规范A179/A179M-90a(1996)e1 热交换器和冷凝器用无缝冷拉低碳钢管A181/A181M-01 普通锻制碳素钢管的规格A182/A182M-01 高温设备用锻制或轧制的合金钢管法兰、锻制管件、阀门及零件A183-98 钢轨用碳素钢螺栓和螺母A184/A184M-01 混凝土加筋用变形钢筋编织网A185-97 钢筋混凝土用焊接钢丝结构A1-00 碳素钢丁字轨A192/A192M-91(1996)e1 高压用无缝碳素钢锅炉管A193/A193M-01 高温设备用合金钢和不锈钢螺栓材料A194/A194M-01 高温和高压设备用碳素钢与合金钢螺栓和螺母的规格A197/A197M-00 化铁炉用可锻铸铁A20/A20M-01 压力容器用钢板材通用要求A202/A202M-93(1999) 压力容器用铬锰硅合金钢板A203/A203M-97 压力容器用镍合金钢板A204/A204M-93(1999) 压力容器用钼合金钢板A209/A209M-98 锅炉和过热器用无缝碳钼合金钢管A210/A210M-96 锅炉和过热器用无缝中碳素管A213/A213M-01 无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管A214/A214M-96 热交换器与冷凝器用电阻焊接碳素钢管A216/A216M-93(1998) 高温下使用的适合于熔焊的碳素钢铸件规格A217/A217M-01 适合高温受压零件用合金钢和马氏体不锈钢铸件A21-94(1999) 铁路用未经热处理和经热处理的碳素钢轴A220/A220M-99 珠光体可锻铁A225/A225M-93(1999) 压力容器用锰矾镍合金钢板A227/A227M-99 机械弹簧用冷拉钢丝A228/A228M-00 乐器用优质弹簧钢丝A229/A229M-99 机械弹簧用油回火的钢丝A230/A230M-99 阀门用油回火优质碳素钢弹簧丝A231/A231M-96 铬钒合金钢弹簧丝A232/A232M-99 阀门用优质铬钒合金钢弹簧丝A234/A234M-00a 中温与高温下使用的锻制碳素钢及合金钢管配件A239-95(1999) 用普力斯试验法(硫酸铜浸蚀)确定铁或钢制品上镀锌层最薄点的测试方法A240/A240M-01 压力容器用耐热铬及铬镍不锈钢板、薄板及带材A242/A242M-00a 高强度低合金结构钢A247-67(1998) 铁铸件中石墨显微结构评定试验方法A249/A249M-01 锅炉、过热器、换热器和冷凝器用焊接奥氏体钢管A250/A250M-95(2001) 锅炉和过热器用电阻焊铁素体合金钢管A252-98e1 焊接钢和无缝钢管桩A254-97 铜焊钢管规格A255-99 测定钢淬透性用末端淬火试验的标准试验方法A262-98 奥氏体不锈钢晶间浸蚀敏感性的检测A263-94a(1999) 耐腐蚀铬钢包覆板材,薄板材及带材技术规范A264-94a(1999) 包覆的不锈铬镍钢板,薄板及带材规格A265-94a(1999) 镍和镍基合金包覆钢板规格A266/A266M-99 压力容器部件用碳素钢锻件规格A268/A268M-01 一般设备用无缝和焊接铁素体与马氏体不锈钢管A269-01 一般设备用无缝和焊接奥氏体不锈钢管A27/A27M-95(2000) 通用碳素钢铸件A270-01 卫生设施用无缝钢和焊接奥氏体不锈钢管A275/A275M-98 钢锻件的磁粉检查试验方法A276-00a 不锈钢棒材和型材A278-93 适用于650F容压部件用灰铸铁件的技术规范A283/A283M-00 低和中等抗拉强度碳素钢板A285/A285M-90(2001) 压力容器用低和中等抗拉强度的碳素钢板A288-91(1998) 涡轮发电机磁性定位环用碳素钢和合金钢锻件A289/A289M-97 发电机非磁性定位环用合金钢锻件的技术规范A29/A29M-99e1 热锻及冷加工碳素钢和合金钢棒A2-90(1997) 普通型,带槽和防护型碳素工字钢轨A290-95(1999) 减速器环用碳素钢和合金钢锻件A291-95(1999) 减速器小齿轮、齿轮和心轴用碳素钢和合金钢锻件A295-98 高碳耐磨轴承钢技术规范A297/A297M-97(1998) 一般用耐热铬铁与镍铬铁合金钢铸件规格A299/A299M-97e1 压力容器用锰硅碳钢板A302/A302M-97e1 压力容器用锰钼和锰钼镍合金钢板A304-96 有末端淬火淬透性要求的合金钢棒材的技术规范A307-00 抗拉强度为60000psi的碳素钢螺栓和螺柱的技术规范A308-99 经热浸处理镀有铅锡合金的薄板材的技术规范A309-94a(1999) 用三点试验法测定长镀锌薄钢板镀层的重量成分的试验方法A311/A311M-95(2000) 有机械性能要求的消除应力的冷拉碳素钢棒A312/A312M-00c 无缝和焊接奥氏体不锈钢管A313/A313M-98 不锈钢弹簧丝技术规范A314-97 锻造用不锈及耐热钢坯及钢棒规格A31-00 钢铆钉及铆钉和压力容器用棒材A319-71(2001) 高温无压部件用灰铁铸件A320/A320M-01 低温用合金钢螺栓材料规格A321-90(1995)e1 经淬火和回火的碳素钢棒A322-91(1996) 合金钢棒材.级别A323-93(2000) 硼铁规格A324-73(2000) 钛铁合金A325-00 经热处理最小抗拉强度为120/105ksi的钢结构螺栓A325M-00 结构钢连接件用高强度螺栓(米制)A327-91(1997) 铸铁冲击试验方法A327M-91(1997) 铸铁冲击试验方法(米制)A328/A328M-00 薄钢板桩A331-95(2000) 冷加工合金钢棒A333/A333M-99 低温用无缝与焊接钢管规格A334/A334M-99 低温设备用无缝与焊接碳素和合金钢管A335/A335M-01 高温用无缝铁素体合金钢管A336/A336M-99e1 压力与高温部件用合金钢锻件规格A338-84(1998) 铁路,船舶和其他重型装备在温度达到650华氏度(345摄氏度)时使用的可锻铸铁法兰,管件和阀门零件A34/A34M-96 磁性材料的抽样和采购试验的标准惯例A340-99a 有关磁性试验用符号和定义的术语A341/A341M-00 用直流磁导计和冲击试验法测定材料的直流磁性能的试验方法A342/A342M-99 磁铁材料导磁率的试验方法A343-97 在电力频率下用瓦特计-安培计-伏特计法(100-1000赫兹)和25 厘米艾普斯亭(EPSTEIN) 机架测定材料的交流电磁性能的试验方法A345-98 磁设备用平轧电炉钢A348/A348M-00 用瓦特计--安培计--伏特计法(100-10000赫兹)和25厘米艾普斯亭框测定材料的交流磁性能的试验方法A350/A350M-00c 要求进行缺口韧性试验的管道部件用碳素钢与低合金钢锻件技术规范A351/A351M-00 容压零件用奥氏体及奥氏体铁素体铸铁的技术规范A352/A352M-93(1998) 低温受压零件用铁素体和马氏体钢铸件规格A353/A353M-93(1999) 压力容器用经二次正火及回火处理的含9％镍的合金钢板A354-01 淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格A355-89(2000) 渗氮用合金钢棒A356/A356M-98e1 蒸汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件A358/A358M-01 高温用电熔焊奥氏体铬镍合金钢管A36/A36M-00a 碳素结构钢技术规范A363-98 地面架空线用镀锌钢丝绳A367-60(1999) 铸铁的激冷试验方法A368-95a(2000) 不锈钢和耐热钢丝绳的标准A369/A369M-01 高温用锻制和镗孔碳素钢管和铁素体合金钢管A370-97a 钢制品机械测试的标准试验方法和定义A372/A372M-99 薄壁压力容器用碳素钢及合金钢锻件A376/A376M-01 高温中心站用无缝奥氏钢管A377-99 球墨铸铁压力管规范索引A380-99e1 不锈钢零件、设备和系统的清洗和除垢A381-96 高压输送用金属弧焊钢管A384-76(1996) 防止钢组件热浸镀锌时翘曲和扭曲用安全保护A385-00 提供高质量镀锌覆层(热浸)A3-01 低、中、高碳素钢鱼尾（连接）板A387/A387M-99e1 压力容器用铬钼合金钢板A388/A388M-95(2000)e1 重型钢锻件超声波检测A389/A389M-93(1998) 适合高温受压部件用经特殊热处理的合金钢铸件规格A390-95(2001) 饲养家禽用镀锌钢丝栏栅网(六角形和直线形)A391/A391M-98 80号合金钢链条A392-96 镀锌钢丝链环栏栅网A394-00 传动塔架用镀锌和裸露钢螺栓A395/A395M-99 高温用铁素体球墨铸铁受压铸件A400-69(2000) 钢棒的成分及机械性能选择指南A401/A401M-98 铬硅合金钢丝A403/A403M-00b 锻制奥氏体不锈钢管配件A407-93(1998) 盘簧用冷拉钢丝A409/A409M-01 腐蚀场所或高温下使用的焊接大口径奥氏体钢管A411-98 镀锌低碳钢铠装线A413/A413M-00 碳素钢链A414/A414M-00 压力容器用碳素薄钢板A416/A416M-99 预应力混凝土用无涂层七股钢铰线A417-93(1998) 之字型、方型和正弦型装垫弹簧元件用冷拉钢丝A418-99 涡轮机及发电机钢转子锻件的超声波检查方法A420/A420M-00b 低温下用锻制碳素钢和合金钢管配件A421/A421M-98a 预应力混凝土用无涂层消除应力钢丝的技术规范A423/A423M-95(2000) 无缝和电焊低合金钢管A424-00 搪瓷用钢薄板A426-92(1997) 高温用离心铸造的铁素体合金钢管A427-74(1996)e1 冷轧和热轧用锻制合金钢辊A428/A428M-01 钢铁制品上铝覆层重量的测试方法A434-90a(2000) 热轧与冷精轧经回火及淬火的合金钢棒A435/A435M-90(2001) 钢板的直射束纵向超声波检验A436-84(1997)e1 奥氏体灰口铁铸件A437/A437M-01 高温用经特殊处理的涡轮型合金钢螺栓材料A438-80(1997) 灰铸铁横向弯曲试验A439-83(1999) 奥氏体可锻铸铁铸件A447/A447M-93(1998) 高温用镍铬铁合金钢铸件(25-12级)A449-00 经淬火和回火的钢螺栓和螺柱A450/A450M-96a 碳素钢管、铁素体合金钢管及奥氏体合金钢管A451-93(1997) 高温用离心铸造的奥氏体钢管A453/A453M-00 具有同奥氏体钢相类似的膨胀系数、屈服强度为50-120Ksi(345-827MPa)的耐高温螺栓材料A455/A455M-90(2001) 压力容器用高强度碳锰钢板A456/A456M-99 大型曲轴锻件的磁粉检查A459-97 镀锌平轧扁钢铠装带A460-94(1999) 包铜钢丝绳标准A463/A463M-00 热浸镀铝薄钢板A466/A466M-98 非焊接碳素钢链A467/A467M-98 机器链和盘旋链A469-94a(1999) 用于发电机转子的真空处理钢锻件A470-01 涡轮机转子和轴用经真空处理的碳素钢和合金锻件A471-94(1999) 涡轮转子转盘和转轮用真空处理合金钢锻件技术规范A472-98 蒸汽涡轮机轴及转子锻件的热稳定性的试验方法A473-01 不锈和耐热钢锻件A474-98 包铝钢丝绳标准A475-98 镀锌钢丝绳A476/A476M-00 造纸厂干燥辊用球墨可锻铸铁件A478-97 铬镍不锈钢和耐热钢制编织钢丝A479/A479M-00 锅炉及压力容器用不锈钢和耐热钢棒与型材A47/A47M-99 铁素体可锻铁铸件A480/A480M-01 扁平轧制耐热不锈钢厚板材、薄板材和带材通用要求A481-94(2000) 金属铬A482-93(2000) 铬铁硅A483-64(2000) 硅锰合金A484/A484M-00 不锈及耐热锻钢棒,钢坯及锻件的规格A485-00 高淬透性耐磨轴承钢的技术规范A487/A487M-93(1998) 受压钢铸件A488/A488M-01 钢铸件焊接规程和工作人员的合格鉴定A48-94ae1 灰铁铸件A489-00 碳素钢吊耳A490-00 最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓A491-96 镀铝钢链环栏栅结构A492-95(2000) 耐热不锈钢丝绳A493-95(2000) 冷镦和冷锻不锈钢和耐热钢丝A494/A494M-00 镍和镍合金铸件A495-94(2000) 硅钙合金钢技术规范A496-97ae1 钢筋混凝土用变形钢丝A497-99e1 钢筋混凝土用焊接变形钢丝网A498-98 无缝与焊接碳素钢,铁素体钢与奥氏体钢制有整体散热片的换热器钢管A49-01 经热处理的碳素钢鱼尾（连接）板，微合金鱼尾板及锻制碳素钢异型鱼尾板A499-89(1997)e1 轧制丁字钢轨用的碳素钢棒材及型材的技术规范A500-01 圆形与异型焊接与无缝碳素钢结构管A501-01 热成型焊接与无缝碳素钢结构管A503/A503M-01 锻制大型曲轴的超声波检验A504-93(1999) 锻制碳素钢轮A505-00 热轧和冷轧合金钢薄板和带材A506-00 正规质量及优质结构的热轧和冷轧合金钢薄板与带材A507-00 优质拉拔,热轧和冷轧合金钢薄板与带材A508/A508M-95(1999) 压力容器用经回火和淬火真空处理的碳素钢与合金钢锻件A510-00 碳素钢盘条和粗圆钢丝通用要求A510M-00 碳素钢盘条和粗圆钢丝(米制)A511-96 无缝不锈钢机械管A512-96 冷拉对缝焊碳素钢机械管A513-00 电阻焊碳素钢与合金钢机械钢管A514/A514M-00a 焊接用经回火与淬火的高屈服强度合金钢板A515/A515M-92(1997) 中温及高温压力容器用碳素钢板A516/A516M-90(2001) 中温及低温压力容器用碳素钢板A517/A517M-93(1999) 压力容器用经回火与淬火的高强度合金钢板A518/A518M-99 耐蚀高硅铁铸件A519-96 无缝碳素钢与合金钢机械管A521-96 一般工业用闭式模钢锻件A522/A522M-95b(2000) 低温用锻制或轧制含镍8%和9%的合金钢法兰,配件,阀门和零件规格A523-96 高压管型电缆线路用平端无缝与电阻焊钢管A524-96 常温和低温用无缝碳素钢管A529/A529M-00 高强度碳锰结构钢质量A530/A530M-99e1 特种碳素钢和合金钢管A531/A531M-91(1996) 涡轮发电机钢定位环的超声波检验A532/A532M-93a(1999)e1 耐磨铸铁A533/A533M-93(1999) 压力容器用经回火和淬火的锰钼及锰钼镍合金钢板A534-94 用于耐摩擦轴承的渗碳钢A536-84(1999)e1 球墨铸铁件A537/A537M-95(2000) 压力容器用经热处理的碳锰硅钢板A53/A53M-01 无镀层热浸的、镀锌的、焊接的及无缝钢管的技术规范A539-99 天然气和燃料油管线用电阻焊钢盘管A540/A540M-00 特殊用途的合金钢螺栓材料A541/A541M-95(1999) 压力容器部件用经淬火和回火的碳素钢及合金钢锻件A542/A542M-99e1 压力容器用经回火和淬火的铬钼、铬钼钒及铬钼钒钛硼合金钢板A543/A543M-93(1999) 压力容器用经回火和淬火的镍铬钼合金钢板A550-78(2000) 铌铁合金A551-94(1999) 钢轮箍A553/A553M-95(2000) 压力容器用经回火和淬火的含8%及9%镍的合金钢板A554-98e1 焊接的无缝钢机械管A555/A555M-97 耐热不锈钢丝和盘条的通用要求A556/A556M-96 无缝冷拉碳素钢给水加热器管A560/A560M-93(1998) 铬镍合金铸件A561-71(1999) 工具钢棒的宏观刻蚀试验A562/A562M-90(2001) 搪玻璃或扩散金属镀层的压力容器用锰钛合金碳素钢板A563-00 碳合金钢螺母。

美国钢铁产品的标准比较多

美国钢铁产品的标准比较多，主要有以下几种：美国钢铁产品的标准比较多，主要有以下几种：ANSI 美国国家标准AISI??美国钢铁学会标准ASTM 美国材料与试验协会标准ASME 美国机械工程师协会标准AMS 航天材料规格（美国航空工业最常用的一种材料规格，由SAE制定）API 美国石油学会标准AWS 美国焊接协会标准SAE 美国机动车工程师协会标准MIL 美国军用标准QQ 美国联邦政府标准A216:：WCB , WCCA217: WC6 , WC9 , C5 (ZGCr5Mo)A351: CF8 , CF3 , CF3 M , CF8C标准号? ? ? ? 标准中文名称? ? ? ? 标准英文名称ASTM A1-00 ? ? ? ? 碳素钢丁字轨? ? ? ? Standard Specification for Carbon Steel Tee Rails ASTM A2-02 ? ? ? ? 普通型,带槽和防护型碳素工字钢轨? ? ? ? Standard Specification for Carbon Steel Girder Rails of Plain, Grooved, and Guard TypesASTM A3-01 ? ? ? ? 低、中、高碳素钢鱼尾（连接）板? ? ? ? Standard Specification for Steel Joint Bars, Low, Medium, and High Carbon (Non-Heat-Treated)ASTM A6/A6M-04a ? ? ? ? 轧制结构钢板材、型材和薄板桩通用技术要求? ? ? ? Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling ASTM A20/A20M-04a ? ? ? ? 压力容器用钢板材通用要求? ? ? ? Standard Specification for General Requirements for Steel Plates for Pressure VesselsASTM A27/A27M-03 ? ? ? ? 通用碳素钢铸件? ? ? ? Standard Specification for Steel Castings, Carbon, for General ApplicationASTM A29/A29M-04 ? ? ? ? 热锻及冷加工碳素钢和合金钢棒? ? ? ? Standard Specification for Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements forASTM A31-04 ? ? ? ? 钢铆钉及铆钉和压力容器用棒材? ? ? ? Standard Specification for Steel Rivets and Bars for Rivets, Pressure VesselsASTM A34/A34M-01 ? ? ? ? 磁性材料的抽样和采购试验的标准惯例? ? ? ? Standard Practice for Sampling and Procurement Testing of Magnetic MaterialsASTM A36/A36M-04 ? ? ? ? 碳素结构钢技术规范? ? ? ? Standard Specification for Carbon Structural SteelASTM A47/A47M-99 ? ? ? ? 铁素体可锻铁铸件? ? ? ? Standard Specification for Ferritic Malleable Iron CastingsASTM A48/A48M-03 ? ? ? ? 灰铁铸件? ? ? ? Standard Specification for Gray Iron CastingsASTM A49-01 ? ? ? ? 经热处理的碳素钢鱼尾（连接）板，微合金鱼尾板及锻制碳素钢异型鱼尾板? ? ? ? Standard Specification for Heat-Treated Carbon Steel Joint Bars, Microalloyed Joint Bars, and Forged Carbon Steel Compromise Joint BarsASTM A53/A53M-04 ? ? ? ? 无镀层热浸的、镀锌的、焊接的及无缝钢管的技术规范? ? ? ? Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and SeamlessASTM A65-01 ? ? ? ? 钢轨道钉? ? ? ? Standard Specification for Steel Track SpikesASTM A66-01 ? ? ? ? 钢质螺旋道钉? ? ? ? Standard Specification for Steel Screw SpikesASTM A67-00 ? ? ? ? 热加工低碳钢和高碳钢垫板技术规范? ? ? ? Standard Specification for Steel Tie Plates, Low-Carbon and High-Carbon Hot-WorkedASTM A74-04 ? ? ? ? 铸铁污水管及配件的技术规范? ? ? ? Standard Specification for Cast Iron Soil Pipe and FittingsASTM A82-02 ? ? ? ? 钢筋混凝土用无节钢丝? ? ? ? Standard Specification for Steel Wire, Plain, for Concrete ReinforcementASTM A90/A90M-01 ? ? ? ? 镀锌和镀锌合金钢铁制品镀层重量的试验方法? ? ? ? Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings ASTM A99-03 ? ? ? ? 锰铁合金? ? ? ? Standard Specification for FerromanganeseASTM A100-04 ? ? ? ? 硅铁? ? ? ? Standard Specification for FerrosiliconASTM A101-04 ? ? ? ? 铬铁? ? ? ? Standard Specification for FerrochromiumASTM A102-04 ? ? ? ? 钒铁合金? ? ? ? Standard Specification for FerrovanadiumASTM A105/A105M-03 ? ? ? ? 管系部件用碳素钢锻件? ? ? ? Standard Specification for Carbon Steel Forgings for Piping ApplicationsASTM A106/A106M-04a ? ? ? ? 高温用无缝碳素钢管? ? ? ? Standard Specification for Seamless Carbon Steel Pipe for High-Temperature ServiceASTM A108-03 ? ? ? ? 优质冷加工碳素钢棒材技术规范? ? ? ? Standard Specification for Steel Bar, Carbon and Alloy, Cold-FinishedASTM A109/A109M-03 ? ? ? ? 冷轧碳素钢带技术规范? ? ? ? Standard Specification for Steel, Strip, Carbon Maximum Percent), Cold-RolledASTM A111-99a(2004)e1 ? ? ? ? 电话和电报线路用镀锌"铁"丝规格? ? ? ? Standard Specification for Zinc-Coated (Galvanized) Iron Telephone and Telegraph Line WireASTM A116-00 ? ? ? ? 镀锌钢丝编织栏栅网? ? ? ? Standard Specification for Metallic-Coated, Steel Woven Wire Fence FabricASTM A121-99(2004) ? ? ? ? 镀锌刺钢丝? ? ? ? Standard Specification for Mettalic-Coated Carbon Steel Barbed WireASTM A123/A123M-02 ? ? ? ? 钢铁产品的锌镀层（热浸镀锌）技术规范? ? ? ? Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsASTM A125-96(2001) ? ? ? ? 热处理螺旋形钢弹簧? ? ? ? Standard Specification for Steel Springs, Helical, Heat-TreatedASTM A126-04 ? ? ? ? 阀门、法兰和管配件用灰铁铸件? ? ? ? Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe FittingsASTM A128/A128M-93(2003) ? ? ? ? 钢铸件,奥氏体锰? ? ? ? Standard Specification for Steel Castings, Austenitic ManganeseASTM A131/A131M-04 ? ? ? ? 海船用结构钢? ? ? ? Standard Specification for Structural Steel for ShipsASTM A132-04 ? ? ? ? 钼铁合金? ? ? ? Standard Specification for FerromolybdenumASTM A134-96(2001) ? ? ? ? 电熔(电弧)焊钢管(NPS为16英寸和16英寸以上)? ? ? ? Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over)ASTM A135-01 ? ? ? ? 电阻焊钢管? ? ? ? Standard Specification for Electric-Resistance-Welded Steel PipeASTM A139/A139M-04 ? ? ? ? 电熔(电弧)焊钢管(4英寸以上的)? ? ? ? Standard Specification for Electric-Fusion (Arc)-Welded Steel Pipe (NPS 4 and Over)ASTM A143/A143M-03 ? ? ? ? 热浸镀锌结构钢制品防脆裂措施和探测脆裂的程序? ? ? ? Standard Practice for Safeguarding Against Embrittlement of Hot-Dip Galvanized Structural Steel Products and Procedure for Detecting EmbrittlementASTM A144-02 ? ? ? ? 铁钨合金规范? ? ? ? Specification for FerrotungstenASTM A146-04 ? ? ? ? 氧化钼制品? ? ? ? Standard Specification for Molybdenum Oxide Products ASTM A148/A148M-03 ? ? ? ? 结构用高强度钢铸件? ? ? ? Standard Specification for Steel Castings, High Strength, for Structural PurposesASTM A153/A153M-04 ? ? ? ? 钢铁制金属构件上镀锌层(热浸)? ? ? ? Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel HardwareASTM A159-83(2001) ? ? ? ? 汽车用灰铁铸件? ? ? ? Standard Specification for Automotive Gray Iron CastingsASTM A167-99 ? ? ? ? 不锈钢和耐热铬镍钢板、薄板及带材? ? ? ? Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and StripASTM A176-99 ? ? ? ? 不锈钢和耐热铬钢板、薄板及带材? ? ? ? Standard Specification for Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and StripASTM A178/A178M-02 ? ? ? ? 电阻焊接碳素钢钢管及碳锰钢锅炉和过热器管的技术规范? ? ? ? Standard Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater TubesASTM A179/A179M-90a(2001) ? ? ? ? 热交换器和冷凝器用无缝冷拉低碳钢管? ? ? ? Standard Specification for Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes ASTM A181/A181M-01 ? ? ? ? 普通锻制碳素钢管的规格? ? ? ? Standard Specification for Carbon Steel Forgings, for General-Purpose PipingASTM A182/A182M-02 ? ? ? ? 高温设备用锻制或轧制的合金钢管法兰、锻制管件、阀门及零件? ? ? ? Standard Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature ServiceASTM A183-03 ? ? ? ? 钢轨用碳素钢螺栓和螺母? ? ? ? Standard Specification for Carbon Steel Track Bolts and NutsASTM A184/A184M-01 ? ? ? ? 混凝土加筋用变形钢筋编织网? ? ? ? Standard Specification for Fabricated Deformed Steel Bar Mats for Concrete ReinforcementASTM A185-02 ? ? ? ? 钢筋混凝土用焊接钢丝结构? ? ? ? Standard Specification for Steel Welded Wire Reinforcement, Plain, for ConcreteASTM A192/A192M-02 ? ? ? ? 高压用无缝碳素钢锅炉管? ? ? ? Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure ServiceASTM A193/A193M-04b ? ? ? ? 高温设备用合金钢和不锈钢螺栓材料? ? ? ? Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature ServiceASTM A194/A194M-04a ? ? ? ? 高温和高压设备用碳素钢与合金钢螺栓和螺母的规格? ? ? ? Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or BothASTM A197/A197M-00 ? ? ? ? 化铁炉用可锻铸铁? ? ? ? Standard Specification for Cupola Malleable IronASTM A202/A202M-03 ? ? ? ? 压力容器用铬锰硅合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Manganese-SiliconASTM A203/A203M-97(2003) ? ? ? ? 压力容器用镍合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, NickelASTM A204/A204M-03 ? ? ? ? 压力容器用钼合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, MolybdenumASTM A209/A209M-03 ? ? ? ? 锅炉和过热器用无缝碳钼合金钢管? ? ? ? Standard Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater TubesASTM A210/A210M-02 ? ? ? ? 锅炉和过热器用无缝中碳素管? ? ? ? Standard Specification for Seamless Medium-Carbon Steel Boiler and Superheater TubesASTM A213/A213M-04 ? ? ? ? 无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管? ? ? ? Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, andHeat-Exchanger TubesASTM A214/A214M-96(2001) ? ? ? ? 热交换器与冷凝器用电阻焊接碳素钢管? ? ? ? Standard Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes ASTM A216/A216M-93(2003) ? ? ? ? 高温下使用的适合于熔焊的碳素钢铸件规格? ? ? ? Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High- Temperature ServiceASTM A217/A217M-02 ? ? ? ? 适合高温受压零件用合金钢和马氏体不锈钢铸件? ? ? ? Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature ServiceASTM A220/A220M-99 ? ? ? ? 珠光体可锻铁? ? ? ? Standard Specification for Pearlitic Malleable IronASTM A225/A225M-03 ? ? ? ? 压力容器用锰矾镍合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Vanadium-NickelASTM A227/A227M-99 ? ? ? ? 机械弹簧用冷拉钢丝? ? ? ? Standard Specification for Steel Wire, Cold-Drawn for Mechanical SpringsASTM A228/A228M-02 ? ? ? ? 乐器用优质弹簧钢丝? ? ? ? Standard Specification for Steel Wire, Music Spring QualityASTM A229/A229M-99 ? ? ? ? 机械弹簧用油回火的钢丝? ? ? ? Standard Specification for Steel Wire, Oil-Tempered for Mechanical SpringsASTM A230/A230M-99 ? ? ? ? 阀门用油回火优质碳素钢弹簧丝? ? ? ? Standard Specification for Steel Wire, Oil-Tempered Carbon Valve Spring QualityASTM A231/A231M-96(2002) ? ? ? ? 铬钒合金钢弹簧丝? ? ? ? Standard Specification for Chromium-Vanadium Alloy Steel Spring WireASTM A232/A232M-99 ? ? ? ? 阀门用优质铬钒合金钢弹簧丝? ? ? ? Standard Specification for Chromium-Vanadium Alloy Steel Valve Spring Quality WireASTM A234/A234M-04 ? ? ? ? 中温与高温下使用的锻制碳素钢及合金钢管配件? ? ? ? Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature ServiceASTM A239-95(2004) ? ? ? ? 用普力斯试验法(硫酸铜浸蚀)确定铁或钢制品上镀锌层最薄点的测试方法? ? ? ? Standard Practice for Locating the Thinnest Spot in a Zinc (Galvanized) Coating on Iron or Steel ArticlesASTM A240/A240M-04ae1 ? ? ? ? 压力容器用耐热铬及铬镍不锈钢板、薄板及带材? ? ? ? Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General ApplicationsASTM A242/A242M-04 ? ? ? ? 高强度低合金结构钢? ? ? ? Standard Specification for High-Strength Low-Alloy Structural SteelASTM A247-67(1998) ? ? ? ? 铁铸件中石墨显微结构评定试验方法? ? ? ? Standard Test Method for Evaluating the Microstructure of Graphite in Iron CastingsASTM A249/A249M-04 ? ? ? ? 锅炉、过热器、换热器和冷凝器用焊接奥氏体钢管? ? ? ? Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser TubesASTM A250/A250M-04 ? ? ? ? 锅炉和过热器用电阻焊铁素体合金钢管? ? ? ? Standard Specification for Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and Superheater TubesASTM A252-98(2002) ? ? ? ? 焊接钢和无缝钢管桩? ? ? ? Standard Specification for Welded and Seamless Steel Pipe PilesASTM A254-97(2002) ? ? ? ? 铜焊钢管规格? ? ? ? Standard Specification for Copper-Brazed Steel TubingASTM A255-02 ? ? ? ? 测定钢淬透性用末端淬火试验的标准试验方法? ? ? ? Standard Test Method for Determining Hardenability of SteelASTM A262-03 ? ? ? ? 奥氏体不锈钢晶间浸蚀敏感性的检测? ? ? ? Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless SteelsASTM A263-03 ? ? ? ? 耐腐蚀铬钢包覆板材,薄板材及带材技术规范? ? ? ? Standard Specification for Stainless Chromium Steel-Clad PlateASTM A264-03 ? ? ? ? 包覆的不锈铬镍钢板,薄板及带材规格? ? ? ? Specification for Stainless Chromium-Nickel Steel-Clad PlateASTM A265-03 ? ? ? ? 镍和镍基合金包覆钢板规格? ? ? ? Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel PlateASTM A266/A266M-03a ? ? ? ? 压力容器部件用碳素钢锻件规格? ? ? ? Standard Specification for Carbon Steel Forgings for Pressure Vessel ComponentsASTM A268/A268M-04 ? ? ? ? 一般设备用无缝和焊接铁素体与马氏体不锈钢管? ? ? ? Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General ServiceASTM A269-04 ? ? ? ? 一般设备用无缝和焊接奥氏体不锈钢管? ? ? ? Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General ServiceASTM A270-03a ? ? ? ? 卫生设施用无缝钢和焊接奥氏体不锈钢管? ? ? ? Standard Specification for Seamless and Welded Austenitic Stainless Steel Sanitary TubingASTM A275/A275M-98(2003) ? ? ? ? 钢锻件的磁粉检查试验方法? ? ? ? Standard Test Method for Magnetic Particle Examination of Steel ForgingsASTM A276-04 ? ? ? ? 不锈钢棒材和型材? ? ? ? Standard Specification for Stainless Steel Bars and ShapesASTM A278/A278M-01 ? ? ? ? 适用于650F容压部件用灰铸铁件的技术规范? ? ? ? Standard Specification for Gray Iron Castings for Pressure-Containing Parts for Temperatures Up to 650°F (350°C) ASTM A283/A283M-03 ? ? ? ? 低和中等抗拉强度碳素钢板? ? ? ? Standard Specification for Low and Intermediate Tensile Strength Carbon Steel PlatesASTM A285/A285M-03 ? ? ? ? 压力容器用低和中等抗拉强度的碳素钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile StrengthASTM A288-91(2003) ? ? ? ? 涡轮发电机磁性定位环用碳素钢和合金钢锻件? ? ? ? Standard Specification for Carbon and Alloy Steel Forgings for Magnetic Retaining Rings for Turbine Generators标准号? ? ? ? 标准中文名称? ? ? ? 标准英文名称ASTM A289/A289M-97(2003) ? ? ? ? 发电机非磁性定位环用合金钢锻件的技术规范? ? ? ? Standard Specification for Alloy Steel Forgings for Nonmagnetic Retaining Rings for GeneratorsASTM A290-02 ? ? ? ? 减速器环用碳素钢和合金钢锻件? ? ? ? Standard Specification for Carbon and Alloy Steel Forgings for Rings for Reduction GearsASTM A291-03 ? ? ? ? 减速器小齿轮、齿轮和心轴用碳素钢和合金钢锻件? ? ? ? Standard Specification for Steel Forgings, Carbon and Alloy, for Pinions, Gears and Shafts for Reduction Gears ASTM A295-98 ? ? ? ? 高碳耐磨轴承钢技术规范? ? ? ? Standard Specification for High-Carbon Anti-Friction Bearing SteelASTM A297/A297M-97(2003) ? ? ? ? 一般用耐热铬铁与镍铬铁合金钢铸件规格? ? ? ? Standard Specification for Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat Resistant, for General ApplicationASTM A299/A299M-04 ? ? ? ? 压力容器用锰硅碳钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-SiliconASTM A302/A302M-03 ? ? ? ? 压力容器用锰钼和锰钼镍合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-Nickel ASTM A304-04 ? ? ? ? 有末端淬火淬透性要求的合金钢棒材的技术规范? ? ? ? Standard Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability RequirementsASTM A307-04 ? ? ? ? 抗拉强度为60000psi的碳素钢螺栓和螺柱的技术规范? ? ? ? Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile StrengthASTM A308/A308M-03 ? ? ? ? 经热浸处理镀有铅锡合金的薄板材的技术规范? ? ? ? Standard Specification for Steel Sheet, Terne (Lead-Tin Alloy) Coated by the Hot-Dip ProcessASTM A309-01 ? ? ? ? 用三点试验法测定长镀锌薄钢板镀层的重量成分的试验方法? ? ? ? Standard Test Method for Weight and Composition of Coating on Terne Sheet by the Triple-Spot TestASTM A311/A311M-04 ? ? ? ? 有机械性能要求的消除应力的冷拉碳素钢棒? ? ? ? Standard Specification for Cold-Drawn, Stress-Relieved Carbon Steel Bars Subject to Mechanical Property Requirements ASTM A312/A312M-04a ? ? ? ? 无缝和焊接奥氏体不锈钢管? ? ? ? Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel PipesASTM A313/A313M-03 ? ? ? ? 不锈钢弹簧丝技术规范? ? ? ? Standard Specification for Stainless Steel Spring WireASTM A314-97(2002) ? ? ? ? 锻造用不锈及耐热钢坯及钢棒规格? ? ? ? Standard Specification for Stainless Steel Billets and Bars for ForgingASTM A319-71(2001) ? ? ? ? 高温无压部件用灰铁铸件? ? ? ? Standard Specification for Gray Iron Castings for Elevated Temperatures for Non-Pressure Containing PartsASTM A320/A320M-04 ? ? ? ? 低温用合金钢螺栓材料规格? ? ? ? Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for Low-Temperature ServiceASTM A321-90(2001) ? ? ? ? 经淬火和回火的碳素钢棒? ? ? ? Standard Specification for Steel Bars, Carbon, Quenched and TemperedASTM A322-91(2001)e1 ? ? ? ? 合金钢棒材.级别? ? ? ? Standard Specification for Steel Bars, Alloy, Standard GradesASTM A323-93(2000) ? ? ? ? 硼铁规格? ? ? ? Standard Specification for FerroboronASTM A324-73(2000) ? ? ? ? 钛铁合金? ? ? ? Standard Specification for FerrotitaniumASTM A325-04a ? ? ? ? 经热处理最小抗拉强度为120/105ksi的热处理钢结构螺栓? ? ? ? Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength ASTM A325M-04a ? ? ? ? 经热处理最小抗拉强度为830Mpa的热处理钢结构螺栓? ? ? ? Standard Specification for Structural Bolts, Steel, Heat Treated 830 Mpa Minimum Tensile Strength [Metric] ASTM A327-91(1997) ? ? ? ? 铸铁冲击试验方法? ? ? ? Standard Test Methods for Impact Testing of Cast IronsASTM A327M-91(1997) ? ? ? ? 铸铁冲击试验方法(米制)? ? ? ? Standard Test Methods for Impact Testing of Cast Irons (Metric)ASTM A328/A328M-03 ? ? ? ? 薄钢板桩? ? ? ? Standard Specification for Steel Sheet Piling ASTM A333/A333M-04a ? ? ? ? 低温用无缝与焊接钢管规格? ? ? ? Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature ServiceASTM A334/A334M-04a ? ? ? ? 低温设备用无缝与焊接碳素和合金钢管? ? ? ? Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature ServiceASTM A335/A335M-03 ? ? ? ? 高温用无缝铁素体合金钢管? ? ? ? Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature ServiceASTM A336/A336M-03a ? ? ? ? 压力与高温部件用合金钢锻件规格? ? ? ? Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature PartsASTM A338-84(2004) ? ? ? ? 铁路,船舶和其他重型装备在温度达到650华氏度(345摄氏度)时使用的可锻铸铁法兰,管件和阀门零件? ? ? ? Standard Specification for Malleable Iron Flanges, Pipe Fittings, and Valve Parts for Railroad, Marine, and Other Heavy Duty Service at Temperatures Up to 650°F (345°C)ASTM A340-03a ? ? ? ? 有关磁性试验用符号和定义的术语? ? ? ? Standard Terminology of Symbols and Definitions Relating to Magnetic TestingASTM A341/A341M-00 ? ? ? ? 用直流磁导计和冲击试验法测定材料的直流磁性能的试验方法? ? ? ? Standard Test Method for Direct Current Magnetic Properties of Materials Using D-C Permeameters and the Ballistic Test MethodsASTM A342/A342M-99 ? ? ? ? 磁铁材料导磁率的试验方法? ? ? ? Standard Test Methods for Permeability of Feebly Magnetic MaterialsASTM A343/A343M-03 ? ? ? ? 在电力频率下用瓦特计-安培计-伏特计法(100-1000赫兹)和25 厘米艾普斯亭(EPSTEIN) 机架测定材料的交流电磁性能的试验方法? ? ? ? Standard Test Method forAlternating-Current Magnetic Properties of Materials at Power Frequencies UsingWattmeter-Ammeter-Voltmeter Method and 25-cm Epstein Test FrameASTM A345-98 ? ? ? ? 磁设备用平轧电炉钢? ? ? ? Standard Specification for Flat-Rolled Electrical Steels for Magnetic ApplicationsASTM A348/A348M-00 ? ? ? ? 用瓦特计--安培计--伏特计法(100-10000赫兹)和25厘米艾普斯亭框测定材料的交流磁性能的试验方法? ? ? ? Standard Test Method for Alternating Current Magnetic Properties of Materials Using the Wattmeter-Ammeter-Voltmeter Method, 100 to 10 000 Hz and 25-cm Epstein FrameASTM A350/A350M-04 ? ? ? ? 要求进行缺口韧性试验的管道部件用碳素钢与低合金钢锻件技术规范? ? ? ? Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping ComponentsASTM A351/A351M-03 ? ? ? ? 容压零件用奥氏体及奥氏体铁素体铸铁的技术规范? ? ? ? Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing PartsASTM A352/A352M-03 ? ? ? ? 低温受压零件用铁素体和马氏体钢铸件规格? ? ? ? Standard Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing Parts, Suitable for Low-Temperature ServiceASTM A353/A353M-93(1999) ? ? ? ? 压力容器用经二次正火及回火处理的含9％镍的合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel,Double-Normalized and TemperedASTM A354-04 ? ? ? ? 淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格? ? ? ? Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded FastenersASTM A355-89(2000) ? ? ? ? 渗氮用合金钢棒? ? ? ? Standard Specification for Steel Bars, Alloys, for NitridingASTM A356/A356M-98(2003) ? ? ? ? 蒸汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件? ? ? ? Standard Specification for Steel Castings, Carbon, Low Alloy, and Stainless Steel, Heavy-Walled for Steam TurbinesASTM A358/A358M-04 ? ? ? ? 高温用电熔焊奥氏体铬镍合金钢管? ? ? ? Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General ApplicationsASTM A363-03 ? ? ? ? 地面架空线用镀锌钢丝绳? ? ? ? Standard Specification for Zinc-Coated (Galvanized) Steel Overhead Ground Wire StrandASTM A367-60(1999) ? ? ? ? 铸铁的激冷试验方法? ? ? ? Standard Test Methods of Chill Testing of Cast IronASTM A368-95a(2000) ? ? ? ? 不锈钢和耐热钢丝绳的标准? ? ? ? Standard Specification for Stainless Steel Wire StrandASTM A369/A369M-02 ? ? ? ? 高温用锻制和镗孔碳素钢管和铁素体合金钢管? ? ? ? Standard Specification for Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature ServiceASTM A370-03a ? ? ? ? 钢制品机械测试的标准试验方法和定义? ? ? ? Standard Test Methods and Definitions for Mechanical Testing of Steel Products标准号? ? ? ? 标准中文名称? ? ? ? 标准英文名称ASTM A372/A372M-03 ? ? ? ? 薄壁压力容器用碳素钢及合金钢锻件? ? ? ? Standard Specification for Carbon and Alloy Steel Forgings for Thin-Walled Pressure VesselsASTM A376/A376M-02a ? ? ? ? 高温中心站用无缝奥氏钢管? ? ? ? Standard Specification for Seamless Austenitic Steel Pipe for High-Temperature Central-Station ServiceASTM A377-03 ? ? ? ? 球墨铸铁压力管规范索引? ? ? ? Standard Index of Specifications for Ductile-Iron Pressure PipeASTM A380-99e1 ? ? ? ? 不锈钢零件、设备和系统的清洗和除垢? ? ? ? Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and SystemsASTM A381-96(2001) ? ? ? ? 高压输送用金属弧焊钢管? ? ? ? Standard Specification forMetal-Arc-Welded Steel Pipe for Use With High-Pressure Transmission SystemsASTM A384/A384M-02 ? ? ? ? 防止钢组件热浸镀锌时翘曲和扭曲用安全保护? ? ? ? Standard Practice for Safeguarding Against Warpage and Distortion During Hot-Dip Galvanizing of Steel Assemblies ASTM A385-03 ? ? ? ? 提供高质量镀锌覆层(热浸)? ? ? ? Standard Practice for Providing High-Quality Zinc Coatings (Hot-Dip)ASTM A387/A387M-03 ? ? ? ? 压力容器用铬钼合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-MolybdenumASTM A388/A388M-03 ? ? ? ? 重型钢锻件超声波检测? ? ? ? Standard Practice for Ultrasonic Examination of Heavy Steel ForgingsASTM A389/A389M-03 ? ? ? ? 适合高温受压部件用经特殊热处理的合金钢铸件规格? ? ? ? Standard Specification for Steel Castings, Alloy, Specially Heat-Treated, for Pressure-Containing Parts, Suitable for High-Temperature ServiceASTM A390-95(2001) ? ? ? ? 饲养家禽用镀锌钢丝栏栅网(六角形和直线形)? ? ? ? Standard Specification for Zinc-Coated (Galvanized) Steel Poultry Fence Fabric (Hexagonal and Straight Line)ASTM A391/A391M-01 ? ? ? ? 80号合金钢链条? ? ? ? Standard Specification for Grade 80 Alloy Steel ChainASTM A392-03 ? ? ? ? 镀锌钢丝链环栏栅网? ? ? ? Standard Specification for Zinc-Coated Steel Chain-Link Fence FabricASTM A394-04 ? ? ? ? 传动塔架用镀锌和裸露钢螺栓? ? ? ? Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and BareASTM A395/A395M-99e1 ? ? ? ? 高温用铁素体球墨铸铁受压铸件? ? ? ? Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated TemperaturesASTM A400-69(2000) ? ? ? ? 钢棒的成分及机械性能选择指南? ? ? ? Standard Practice for Steel Bars, Selection Guide, Composition, and Mechanical PropertiesASTM A401/A401M-03 ? ? ? ? 铬硅合金钢丝? ? ? ? Standard Specification for Steel Wire, Chromium-Silicon AlloyASTM A403/A403M-04 ? ? ? ? 锻制奥氏体不锈钢管配件? ? ? ? Standard Specification for Wrought Austenitic Stainless Steel Piping FittingsASTM A407-93(2004) ? ? ? ? 盘簧用冷拉钢丝? ? ? ? Standard Specification for Steel Wire, Cold-Drawn, for Coiled-Type SpringsASTM A409/A409M-01 ? ? ? ? 腐蚀场所或高温下使用的焊接大口径奥氏体钢管? ? ? ? Standard Specification for Welded Large Diameter Austenitic Steel Pipe for Corrosive or High-Temperature ServiceASTM A411-03 ? ? ? ? 镀锌低碳钢铠装线? ? ? ? Standard Specification for Zinc-Coated (Galvanized) Low-Carbon Steel Armor WireASTM A413/A413M-01 ? ? ? ? 碳素钢链? ? ? ? Standard Specification for Carbon Steel Chain ASTM A414/A414M-04 ? ? ? ? 压力容器用碳素薄钢板? ? ? ? Standard Specification for Steel, Sheet, Carbon, for Pressure VesselsASTM A416/A416M-02 ? ? ? ? 预应力混凝土用无涂层七股钢铰线? ? ? ? Standard Specification for Steel Strand, Uncoated Seven-Wire for Prestressed ConcreteASTM A417-93(2004) ? ? ? ? 之字形、方形、正弦形家具用弹簧元件用冷拔钢丝? ? ? ? Standard Specification for Steel Wire, Cold-Drawn, for Zig-Zag, Square-Formed, and Sinuous-Type Upholstery Spring UnitsASTM A418-99(2003) ? ? ? ? 涡轮机及发电机钢转子锻件的超声波检查方法? ? ? ? Standard Test Method for Ultrasonic Examination of Turbine and Generator Steel Rotor ForgingsASTM A420/A420M-04 ? ? ? ? 低温下用锻制碳素钢和合金钢管配件? ? ? ? Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature ServiceASTM A421/A421M-02 ? ? ? ? 预应力混凝土用无涂层消除应力钢丝的技术规范? ? ? ? Standard Specification for Uncoated Stress-Relieved Steel Wire for Prestressed ConcreteASTM A423/A423M-95(2000) ? ? ? ? 无缝和电焊低合金钢管? ? ? ? Standard Specification for Seamless and Electric-Welded Low-Alloy Steel TubesASTM A424-00 ? ? ? ? 搪瓷用钢薄板? ? ? ? Standard Specification for Steel, Sheet, for Porcelain EnamelingASTM A426/A426M-02 ? ? ? ? 高温用离心铸造的铁素体合金钢管? ? ? ? Standard Specification for Centrifugally Cast Ferritic Alloy Steel Pipe for High-Temperature ServiceASTM A427-02 ? ? ? ? 冷轧和热轧用锻制合金钢辊? ? ? ? Standard Specification for Wrought Alloy Steel Rolls for Cold and Hot ReductionASTM A428/A428M-01 ? ? ? ? 钢铁制品上铝覆层重量的测试方法? ? ? ? Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel ArticlesASTM A434-04 ? ? ? ? 热轧与冷精轧经回火及淬火的合金钢棒? ? ? ? Standard Specification for Steel Bars, Alloy, Hot-Wrought or Cold-Finished, Quenched and TemperedASTM A435/A435M-90(2001) ? ? ? ? 钢板的直射束纵向超声波检验? ? ? ? Standard Specification for Straight-Beam Ultrasonic Examination of Steel PlatesASTM A436-84(2001) ? ? ? ? 奥氏体灰口铁铸件? ? ? ? Standard Specification for Austenitic Gray Iron CastingsASTM A437/A437M-01a ? ? ? ? 高温用经特殊处理的涡轮型合金钢螺栓材料? ? ? ? Standard Specification for Alloy-Steel Turbine-Type Bolting Material Specially Heat Treated for High-Temperature ServiceASTM A439-83(1999) ? ? ? ? 奥氏体可锻铸铁铸件? ? ? ? Standard Specification for Austenitic Ductile Iron CastingsASTM A447/A447M-93(2003) ? ? ? ? 高温用镍铬铁合金钢铸件(25-12级)? ? ? ? Standard Specification for Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service ASTM A449-04a ? ? ? ? 经淬火和回火的钢螺栓和螺柱? ? ? ? Standard Specification for Quenched and Tempered Steel Bolts and StudsASTM A450/A450M-04 ? ? ? ? 碳素钢管、铁素体合金钢管及奥氏体合金钢管? ? ? ? Standard Specification for General Requirements for Carbon, Ferritic Alloy, and Austenitic Alloy Steel TubesASTM A451/A451M-02 ? ? ? ? 高温用离心铸造的奥氏体钢管? ? ? ? Standard Specification for Centrifugally Cast Austenitic Steel Pipe for High-Temperature ServiceASTM A453/A453M-03 ? ? ? ? 具有同奥氏体钢相类似的膨胀系数、屈服强度为50-120Ksi(345-827MPa)的耐高温螺栓材料? ? ? ? Standard Specification for High-Temperature Bolting Materials, with Expansion Coefficients Comparable to Austenitic Stainless SteelsASTM A455/A455M-03 ? ? ? ? 压力容器用高强度碳锰钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Carbon Steel, High-Strength ManganeseASTM A456/A456M-99(2003) ? ? ? ? 大型曲轴锻件的磁粉检查? ? ? ? Standard Specification for Magnetic Particle Examination of Large Crankshaft ForgingsASTM A459-97(2003) ? ? ? ? 镀锌平轧扁钢铠装带? ? ? ? Standard Specification for Zinc-Coated Flat Steel Armoring TapeASTM A460-94(2004)e1 ? ? ? ? 包铜钢丝绳标准? ? ? ? Standard Specification for Copper-Clad Steel Wire StrandASTM A463/A463M-02a ? ? ? ? 热浸镀铝薄钢板? ? ? ? Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip ProcessASTM A466/A466M-01 ? ? ? ? 非焊接碳素钢链? ? ? ? Standard Specification for Weldless Chain ASTM A467/A467M-01 ? ? ? ? 机器链和盘旋链? ? ? ? Standard Specification for Machine and Coil Chain标准号? ? ? ? 标准中文名称? ? ? ? 标准英文名称。

ASTM美国材料标准中文版标准目录

ASTM美国材料标准中文版标准目录ASTM A105/A105M-2002 管道部件用碳钢锻件ASTM A106-2002a 高温用无缝碳钢公称管规范ASTM A126-1995(R2001) 阀门、法兰和管道附件用灰铁铸件ASTM A143-2003 热侵镀锌结构钢制品防脆化的标准实施规程和催化探测方法ASTM A179/A179M-1990a（R2001）热交换器和冷凝器用无缝冷拉低碳钢管标准规范ASTM A181/A181M-2001 通用管路用碳钢锻件标准规范"ASTM A182/A182M-2002 高温用锻制或轧制合金钢法兰、锻制管件、阀门和部件ASTM A192-2002 高压设备用无缝碳钢锅炉管标准规范ASTM A193/A193M-2001 高温用合金钢和不锈钢螺栓材料ASTM A194/A194M-2001 a 高温用合金钢和不锈钢螺栓材料ASTM A209/A209M-2003 锅炉和过热器用无缝碳钼合金钢管标准规范!ASTM A210/A210M-2003 锅炉和过热器用无缝中碳钢管技术条件ASTM A213/A213Mb-2004 锅炉过热器和换热器用无缝铁素体和奥氏体合金钢传热管技术条件ASTM A216/A216M-2001 a 高温用可熔焊碳钢铸件标准规范ASTM A217/A217M-2002 高温承压件用马氏体不锈钢和合金钢铸件标准规范ASTM A234/A234M-2004 中、高温用锻制碳钢和合金钢管道配件ASTM A252-98（R2002）焊接钢和无缝钢管桩的标准规范ASTM A262-2002a 探测奥氏体不锈钢晶间腐蚀敏感度的标准实施规范ASTM A269/A269-2004 通用无缝和焊接奥氏体不锈钢管标准规范ASTM A276-2002 a 不锈钢棒材和型材ASTM A278/A278M-2001 高温不超过650°F（350℃）的承压部件用灰铸铁件ASTM A320/A320M-2002 低温用合金钢栓接材料ASTM A333/A333M-2004 低温设备用无缝和焊接钢管的规范标准ASTM A334/A334M-2004 低温设备用无缝和焊接碳素和合金钢管的标准规范ASTM A335-2003 高温设备用无缝铁素体合金钢管标准规范ASTM A350/A350M-2002 要求冲击韧性试验的管件用碳钢及低合金钢锻件标准规范! ASTM A351/A351M-2000 承压件用奥氏体、奥氏体-铁素体（双相）钢铸件规范ASTM A352/A352M-1993（R1998) 低温承压件用铁素体和马氏体钢铸件标准规范ASTM A36/A36M-2004 碳结构钢标准规范ASTM A370/A370M-2003a 钢制品力学性能试验方法和定义标准ASTM A387/A387M-2003 压力容器用铬钼合金钢板的标准规范ASTM A395/A395M-1999 高温用铁素体球墨铸铁承压铸件ASTM A403/A403M-2004 锻制奥氏体不锈钢管配件的标准规范;ASTM A439-1983(R1999) 奥氏体球墨铸铁件ASTM A450/A450M-2004 碳素钢管、铁素体合金钢管及奥氏体合金钢管一般要求的标准规范ASTM A500-2003a 圆形与异型冷成型焊接与无缝碳素钢结构管标准规范ASTM A515-2003 中温及高温压力容器用碳素钢板的标准规范ASTM A516-2004a 中温及低温压力容器用碳素钢板的标准规范ASTM A530-2003 特种碳素钢和合金钢管一般要求的标准规范ASTM A536-1984(R1999) 球墨铸铁件ASTM A6/A6M-2004 a 结构用轧制钢板、型钢、板桩和棒钢通用要求ASTM A615/A615M-2004a 混凝土配筋用异形钢筋和无节钢胚棒标准规范ASTM A694/A694M-2000 高温输送用管法兰、管件、阀门及零件用碳钢和合金钢锻件标准规范)ASTM A703/A703M-2004 标准技术条件—承压件钢铸件通用要求ASTM A781/A781M-2004a 铸件、钢和合金的标准规范及通用工业的一般性要求ASTM A788/A788M-2004a 标准技术条件—钢锻件通用要求ASTM A961-2002 管道用钢制法兰、锻制管件、阀门和零件的通用要求标准规范ASTM A965/A965M-2002 高温高压部件用奥氏体钢锻件ASTM B209/B209M -2004 铝和铝合金薄板和中厚板标准规范ASTM B462-2002 高温耐腐蚀用锻制或轧制的UNS NO6030、UNS NO6022、UNS NO6200、UNS NO8020、UNS NO8024、UNS NO8026、UNS NO8367、UNS NO10276、UNS N10665、UNS N10675和UNS R20033合金管法兰、锻制管件、阀门和零件标准规范ASTM E125-1963（R2003）铁铸件的磁粉检验用标准参考照片ASTM E164-2003 焊件的超声接触检验的标准操作规程ASTM E18-2003 金属材料洛氏硬度和洛氏表面硬度的标准测试方法ASTM E208-1995a(R2000) 用导向落锤试验测定铁素体钢无塑性转变温度的标准试验方法ASTM E213-2004 金属管超声检验方法ASTM E29-2002 使用有效数字确定试验数据与规范符合性作法ASTM E6-2003 金属材料布氏硬度的标准测试方法ASTM E8-2004 金属材料拉伸试验的标准测试方法ASTM E94-2004 放射性检查的标准指南ASTM E 155-2005 铝、镁铸件检验用标准参考射线底片ASTM E 446-1998（R2004）用于厚度在2IN（51MM）以下钢铸件的标准参考射线底片ASTM E 242-2001（R2005）在某些参数变化时射线图像外观用标准参考射线底片ASTM F1030-1986(R1998) 阀门操作装置的选择准则ASTM F1098-1987(R1998) 公称管径有NPS2～24的蝶阀外形尺寸标准规范ASTM F112-1995 色覆垫片密封性能的标准试验方法ASTM F1311-1995(R2001) 大口径组装式碳钢法兰标准规范ASTM F146-1995a 垫片材料耐液体标准试验方法ASTM F1565-2000 蒸汽用减压阀规范ASTM F36-1995 测定垫片材料压缩率及回弹率的标准试验方法ASTM F37-1995 垫片材料密封性的标准试验方法ASTM F38-1995 垫片材料的蠕变松弛的标准试验方法ASTM F885-1984 公称管径为NPS 1/4～2的青铜截止阀外形尺寸标准规范ASTM F992-1986(R2001) 阀门铭牌标准规范ASTM F993-1986(R2001) 阀门锁紧装置标准规范ASTM G1-2003 腐蚀试样的制备、清洁处理和评定用标准实施规范ASTM G36-73(R1981) 标准实用规程：在沸的氯化镁溶液中进行的应力腐蚀裂纹试验(参考资料)ASTM G46-1976(R1986) 标准实用规程：麻点腐蚀的检验和评定(参考资料)ASTM G48-1976(R1980) 使用三氯化铁溶液做不锈钢及其合金的耐麻点腐蚀和抗裂口腐蚀性试验的标准方法（参考资料）ASTM标准中译本丛书（一）碳钢、铸铁、不锈钢及合金钢材料标准规范ASTM标准中译本丛书（二）法兰、管件、阀门及部件（中文版）。

美制螺帽螺栓、螺母母机械性能

14
二、美制内螺纹紧固件机械性能等级标准
产品标准主要有
ASTM A563-2000年《碳钢、合金钢螺母》
SAE J 995《内螺纹紧固件机械性能和材料要求》
ASTM A194/194M-200５年《与高温和高压条件

下使用的螺栓配用的碳钢和合金钢螺母》
15
1、ASTM A563-2000年《碳钢、合金钢螺母》
7
3、 ASTM A193／A193M-2006 《高温下的合金钢和不锈钢螺栓材料》
该标准适用于高温环境下使用的压力容器、阀、法兰和配件上的合金钢和不锈钢栓接材料。标准推荐了36个等级，规定不同的等级选用不同的耐腐蚀合金钢材料或铁素体、奥氏体和马氏体不锈钢材料。省内常生产的几个等级是： B6、B7、B7M是铁氏体钢；B8是奥氏体钢。 ** 规定B7抗拉强度861.25 N／mm2 ；屈服强度723.45 N／mm2 ；伸长率16%；面宿率50%；硬度Max C35、（原标准没有规定硬度要求），现有上限，主要是在保证强度的前题下，确保塑性指标。 ** 应特别注意延伸率试验的标准试样是2寸长，现国内是δ5 %。
由于有的螺母使用在高温和高压的恶劣条件，温度升高时材料强度就降低，如外表镀层剥落、氧化，并出现螺纹咬死现象，这样就对材料和等级提出了较高要求。为此美国材料试验协会推出ASTM A194/194M标准，为适应不同的用途，标准规定了42个等级。
18
3、 ASTM A194/194M-2005年《与高温和高压条件下使用的螺栓配用的碳钢和合金钢螺母》
20
螺母等级标记
ASTM-A563 A级
低碳钢
620 N/mm2
B68
C32
SAE 5级

ASTM A标准(中文)

AA1000-99 弹簧专用碳钢和合金钢钢丝规范A1001-99 大型材高强度钢铸件规范A1002-99 镍铝类合金铸件规范A100-93(2000) 硅铁A101-93(2000) 铬铁A102-93(2000) 钒铁合金A105/A105M-01 管系部件用碳素钢锻件A106-999e1 高温用无缝碳素钢管A108-99 优质冷加工碳素钢棒材技术规范A109/A109M-00e1 冷轧碳素钢带技术规范A111-99a 电话和电报线路用镀锌"铁"丝规格A116-00 镀锌钢丝编织栏栅网A121-99 镀锌刺钢丝A123/A123M-00 钢铁产品的锌镀层（热浸镀锌）技术规范A125-96 热处理螺旋形钢弹簧A126-95(2001) 阀门、法兰和管配件用灰铁铸件A128/A128M-93(1998) 钢铸件,奥氏体锰A131/A131M-94 海船用结构钢A132-89(2000) 钼铁合金A134-96 电熔(电弧)焊钢管(NPS为16英寸和16英寸以上)A135-01 电阻焊钢管A139-00 电熔(电弧)焊钢管(4英寸以上的)A143-74(1999) 热浸镀锌结构钢制品防脆裂措施和探测脆裂的程序A146-64(2000) 氧化钼制品A148/A148M-01 结构用高强度钢铸件A153/A153M-00 钢铁制金属构件上镀锌层(热浸)A159-83(2001) 汽车用灰铁铸件A167-99 不锈钢和耐热铬镍钢板、薄板及带材A176-99 不锈钢和耐热铬钢板、薄板及带材A178/A178M-95(2000) 电阻焊接碳素钢钢管及碳锰钢锅炉和过热器管的技术规范A179/A179M-90a(1996)e1 热交换器和冷凝器用无缝冷拉低碳钢管A181/A181M-01 普通锻制碳素钢管的规格A182/A182M-01 高温设备用锻制或轧制的合金钢管法兰、锻制管件、阀门及零件A183-98 钢轨用碳素钢螺栓和螺母A184/A184M-01 混凝土加筋用变形钢筋编织网A185-97 钢筋混凝土用焊接钢丝结构A1-00 碳素钢丁字轨A192/A192M-91(1996)e1 高压用无缝碳素钢锅炉管A193/A193M-01 高温设备用合金钢和不锈钢螺栓材料A194/A194M-01 高温和高压设备用碳素钢与合金钢螺栓和螺母的规格A197/A197M-00 化铁炉用可锻铸铁A20/A20M-01 压力容器用钢板材通用要求A202/A202M-93(1999) 压力容器用铬锰硅合金钢板A203/A203M-97 压力容器用镍合金钢板A204/A204M-93(1999) 压力容器用钼合金钢板A209/A209M-98 锅炉和过热器用无缝碳钼合金钢管A210/A210M-96 锅炉和过热器用无缝中碳素管A213/A213M-01 无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管A214/A214M-96 热交换器与冷凝器用电阻焊接碳素钢管A216/A216M-93(1998) 高温下使用的适合于熔焊的碳素钢铸件规格A217/A217M-01 适合高温受压零件用合金钢和马氏体不锈钢铸件A21-94(1999) 铁路用未经热处理和经热处理的碳素钢轴A220/A220M-99 珠光体可锻铁A225/A225M-93(1999) 压力容器用锰矾镍合金钢板A227/A227M-99 机械弹簧用冷拉钢丝A228/A228M-00 乐器用优质弹簧钢丝A229/A229M-99 机械弹簧用油回火的钢丝A230/A230M-99 阀门用油回火优质碳素钢弹簧丝A231/A231M-96 铬钒合金钢弹簧丝A232/A232M-99 阀门用优质铬钒合金钢弹簧丝A234/A234M-00a 中温与高温下使用的锻制碳素钢及合金钢管配件A239-95(1999) 用普力斯试验法(硫酸铜浸蚀)确定铁或钢制品上镀锌层最薄点的测试方法A240/A240M-01 压力容器用耐热铬及铬镍不锈钢板、薄板及带材A242/A242M-00a 高强度低合金结构钢A247-67(1998) 铁铸件中石墨显微结构评定试验方法A249/A249M-01 锅炉、过热器、换热器和冷凝器用焊接奥氏体钢管A250/A250M-95(2001) 锅炉和过热器用电阻焊铁素体合金钢管A252-98e1 焊接钢和无缝钢管桩A254-97 铜焊钢管规格A255-99 测定钢淬透性用末端淬火试验的标准试验方法A262-98 奥氏体不锈钢晶间浸蚀敏感性的检测A263-94a(1999) 耐腐蚀铬钢包覆板材,薄板材及带材技术规范A264-94a(1999) 包覆的不锈铬镍钢板,薄板及带材规格A265-94a(1999) 镍和镍基合金包覆钢板规格A266/A266M-99 压力容器部件用碳素钢锻件规格A268/A268M-01 一般设备用无缝和焊接铁素体与马氏体不锈钢管A269-01 一般设备用无缝和焊接奥氏体不锈钢管A27/A27M-95(2000) 通用碳素钢铸件A270-01 卫生设施用无缝钢和焊接奥氏体不锈钢管A275/A275M-98 钢锻件的磁粉检查试验方法A276-00a 不锈钢棒材和型材A278-93 适用于650F容压部件用灰铸铁件的技术规范A283/A283M-00 低和中等抗拉强度碳素钢板A285/A285M-90(2001) 压力容器用低和中等抗拉强度的碳素钢板A288-91(1998) 涡轮发电机磁性定位环用碳素钢和合金钢锻件A289/A289M-97 发电机非磁性定位环用合金钢锻件的技术规范A29/A29M-99e1 热锻及冷加工碳素钢和合金钢棒A2-90(1997) 普通型,带槽和防护型碳素工字钢轨A290-95(1999) 减速器环用碳素钢和合金钢锻件A291-95(1999) 减速器小齿轮、齿轮和心轴用碳素钢和合金钢锻件A295-98 高碳耐磨轴承钢技术规范A297/A297M-97(1998) 一般用耐热铬铁与镍铬铁合金钢铸件规格A299/A299M-97e1 压力容器用锰硅碳钢板A302/A302M-97e1 压力容器用锰钼和锰钼镍合金钢板A304-96 有末端淬火淬透性要求的合金钢棒材的技术规范A307-00 抗拉强度为60000psi的碳素钢螺栓和螺柱的技术规范A308-99 经热浸处理镀有铅锡合金的薄板材的技术规范A309-94a(1999) 用三点试验法测定长镀锌薄钢板镀层的重量成分的试验方法A311/A311M-95(2000) 有机械性能要求的消除应力的冷拉碳素钢棒A312/A312M-00c 无缝和焊接奥氏体不锈钢管A313/A313M-98 不锈钢弹簧丝技术规范A314-97 锻造用不锈及耐热钢坯及钢棒规格A31-00 钢铆钉及铆钉和压力容器用棒材A319-71(2001) 高温无压部件用灰铁铸件A320/A320M-01 低温用合金钢螺栓材料规格A321-90(1995)e1 经淬火和回火的碳素钢棒A322-91(1996) 合金钢棒材.级别A323-93(2000) 硼铁规格A324-73(2000) 钛铁合金A325-00 经热处理最小抗拉强度为120/105ksi的钢结构螺栓A325M-00 结构钢连接件用高强度螺栓(米制)A327-91(1997) 铸铁冲击试验方法A327M-91(1997) 铸铁冲击试验方法(米制)A328/A328M-00 薄钢板桩A331-95(2000) 冷加工合金钢棒A333/A333M-99 低温用无缝与焊接钢管规格A334/A334M-99 低温设备用无缝与焊接碳素和合金钢管A335/A335M-01 高温用无缝铁素体合金钢管A336/A336M-99e1 压力与高温部件用合金钢锻件规格A338-84(1998) 铁路,船舶和其他重型装备在温度达到650华氏度(345摄氏度)时使用的可锻铸铁法兰,管件和阀门零件A34/A34M-96 磁性材料的抽样和采购试验的标准惯例A340-99a 有关磁性试验用符号和定义的术语A341/A341M-00 用直流磁导计和冲击试验法测定材料的直流磁性能的试验方法A342/A342M-99 磁铁材料导磁率的试验方法A343-97 在电力频率下用瓦特计-安培计-伏特计法(100-1000赫兹)和25 厘米艾普斯亭(EPSTEIN) 机架测定材料的交流电磁性能的试验方法A345-98 磁设备用平轧电炉钢A348/A348M-00 用瓦特计--安培计--伏特计法(100-10000赫兹)和25厘米艾普斯亭框测定材料的交流磁性能的试验方法A350/A350M-00c 要求进行缺口韧性试验的管道部件用碳素钢与低合金钢锻件技术规范A351/A351M-00 容压零件用奥氏体及奥氏体铁素体铸铁的技术规范A352/A352M-93(1998) 低温受压零件用铁素体和马氏体钢铸件规格A353/A353M-93(1999) 压力容器用经二次正火及回火处理的含9％镍的合金钢板A354-01 淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格A355-89(2000) 渗氮用合金钢棒A356/A356M-98e1 蒸汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件A358/A358M-01 高温用电熔焊奥氏体铬镍合金钢管A36/A36M-00a 碳素结构钢技术规范A363-98 地面架空线用镀锌钢丝绳A367-60(1999) 铸铁的激冷试验方法A368-95a(2000) 不锈钢和耐热钢丝绳的标准A369/A369M-01 高温用锻制和镗孔碳素钢管和铁素体合金钢管A370-97a 钢制品机械测试的标准试验方法和定义A372/A372M-99 薄壁压力容器用碳素钢及合金钢锻件A376/A376M-01 高温中心站用无缝奥氏钢管A377-99 球墨铸铁压力管规范索引A380-99e1 不锈钢零件、设备和系统的清洗和除垢A381-96 高压输送用金属弧焊钢管A384-76(1996) 防止钢组件热浸镀锌时翘曲和扭曲用安全保护A385-00 提供高质量镀锌覆层(热浸)A3-01 低、中、高碳素钢鱼尾（连接）板A387/A387M-99e1 压力容器用铬钼合金钢板A388/A388M-95(2000)e1 重型钢锻件超声波检测A389/A389M-93(1998) 适合高温受压部件用经特殊热处理的合金钢铸件规格A390-95(2001) 饲养家禽用镀锌钢丝栏栅网(六角形和直线形)A391/A391M-98 80号合金钢链条A392-96 镀锌钢丝链环栏栅网A394-00 传动塔架用镀锌和裸露钢螺栓A395/A395M-99 高温用铁素体球墨铸铁受压铸件A400-69(2000) 钢棒的成分及机械性能选择指南A401/A401M-98 铬硅合金钢丝A403/A403M-00b 锻制奥氏体不锈钢管配件A407-93(1998) 盘簧用冷拉钢丝A409/A409M-01 腐蚀场所或高温下使用的焊接大口径奥氏体钢管A411-98 镀锌低碳钢铠装线A413/A413M-00 碳素钢链A414/A414M-00 压力容器用碳素薄钢板A416/A416M-99 预应力混凝土用无涂层七股钢铰线A417-93(1998) 之字型、方型和正弦型装垫弹簧元件用冷拉钢丝A418-99 涡轮机及发电机钢转子锻件的超声波检查方法A420/A420M-00b 低温下用锻制碳素钢和合金钢管配件A421/A421M-98a 预应力混凝土用无涂层消除应力钢丝的技术规范A423/A423M-95(2000) 无缝和电焊低合金钢管A424-00 搪瓷用钢薄板A426-92(1997) 高温用离心铸造的铁素体合金钢管A427-74(1996)e1 冷轧和热轧用锻制合金钢辊A428/A428M-01 钢铁制品上铝覆层重量的测试方法A434-90a(2000) 热轧与冷精轧经回火及淬火的合金钢棒A435/A435M-90(2001) 钢板的直射束纵向超声波检验A436-84(1997)e1 奥氏体灰口铁铸件A437/A437M-01 高温用经特殊处理的涡轮型合金钢螺栓材料A438-80(1997) 灰铸铁横向弯曲试验A439-83(1999) 奥氏体可锻铸铁铸件A447/A447M-93(1998) 高温用镍铬铁合金钢铸件(25-12级)A449-00 经淬火和回火的钢螺栓和螺柱A450/A450M-96a 碳素钢管、铁素体合金钢管及奥氏体合金钢管A451-93(1997) 高温用离心铸造的奥氏体钢管A453/A453M-00 具有同奥氏体钢相类似的膨胀系数、屈服强度为50-120Ksi(345-827MPa)的耐高温螺栓材料A455/A455M-90(2001) 压力容器用高强度碳锰钢板A456/A456M-99 大型曲轴锻件的磁粉检查A459-97 镀锌平轧扁钢铠装带A460-94(1999) 包铜钢丝绳标准A463/A463M-00 热浸镀铝薄钢板A466/A466M-98 非焊接碳素钢链A467/A467M-98 机器链和盘旋链A469-94a(1999) 用于发电机转子的真空处理钢锻件A470-01 涡轮机转子和轴用经真空处理的碳素钢和合金锻件A471-94(1999) 涡轮转子转盘和转轮用真空处理合金钢锻件技术规范A472-98 蒸汽涡轮机轴及转子锻件的热稳定性的试验方法A473-01 不锈和耐热钢锻件A474-98 包铝钢丝绳标准A475-98 镀锌钢丝绳A476/A476M-00 造纸厂干燥辊用球墨可锻铸铁件A478-97 铬镍不锈钢和耐热钢制编织钢丝A479/A479M-00 锅炉及压力容器用不锈钢和耐热钢棒与型材A47/A47M-99 铁素体可锻铁铸件A480/A480M-01 扁平轧制耐热不锈钢厚板材、薄板材和带材通用要求A481-94(2000) 金属铬A482-93(2000) 铬铁硅A483-64(2000) 硅锰合金A484/A484M-00 不锈及耐热锻钢棒,钢坯及锻件的规格A485-00 高淬透性耐磨轴承钢的技术规范A487/A487M-93(1998) 受压钢铸件A488/A488M-01 钢铸件焊接规程和工作人员的合格鉴定A48-94ae1 灰铁铸件A489-00 碳素钢吊耳A490-00 最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓A491-96 镀铝钢链环栏栅结构A492-95(2000) 耐热不锈钢丝绳A493-95(2000) 冷镦和冷锻不锈钢和耐热钢丝A494/A494M-00 镍和镍合金铸件A495-94(2000) 硅钙合金钢技术规范A496-97ae1 钢筋混凝土用变形钢丝A497-99e1 钢筋混凝土用焊接变形钢丝网A498-98 无缝与焊接碳素钢,铁素体钢与奥氏体钢制有整体散热片的换热器钢管A49-01 经热处理的碳素钢鱼尾（连接）板，微合金鱼尾板及锻制碳素钢异型鱼尾板A499-89(1997)e1 轧制丁字钢轨用的碳素钢棒材及型材的技术规范A500-01 圆形与异型焊接与无缝碳素钢结构管A501-01 热成型焊接与无缝碳素钢结构管A503/A503M-01 锻制大型曲轴的超声波检验A504-93(1999) 锻制碳素钢轮A505-00 热轧和冷轧合金钢薄板和带材A506-00 正规质量及优质结构的热轧和冷轧合金钢薄板与带材A507-00 优质拉拔,热轧和冷轧合金钢薄板与带材A508/A508M-95(1999) 压力容器用经回火和淬火真空处理的碳素钢与合金钢锻件A510-00 碳素钢盘条和粗圆钢丝通用要求A510M-00 碳素钢盘条和粗圆钢丝(米制)A511-96 无缝不锈钢机械管A512-96 冷拉对缝焊碳素钢机械管A513-00 电阻焊碳素钢与合金钢机械钢管A514/A514M-00a 焊接用经回火与淬火的高屈服强度合金钢板A515/A515M-92(1997) 中温及高温压力容器用碳素钢板A516/A516M-90(2001) 中温及低温压力容器用碳素钢板A517/A517M-93(1999) 压力容器用经回火与淬火的高强度合金钢板A518/A518M-99 耐蚀高硅铁铸件A519-96 无缝碳素钢与合金钢机械管A521-96 一般工业用闭式模钢锻件A522/A522M-95b(2000) 低温用锻制或轧制含镍8%和9%的合金钢法兰,配件,阀门和零件规格A523-96 高压管型电缆线路用平端无缝与电阻焊钢管A524-96 常温和低温用无缝碳素钢管A529/A529M-00 高强度碳锰结构钢质量A530/A530M-99e1 特种碳素钢和合金钢管A531/A531M-91(1996) 涡轮发电机钢定位环的超声波检验A532/A532M-93a(1999)e1 耐磨铸铁A533/A533M-93(1999) 压力容器用经回火和淬火的锰钼及锰钼镍合金钢板A534-94 用于耐摩擦轴承的渗碳钢A536-84(1999)e1 球墨铸铁件A537/A537M-95(2000) 压力容器用经热处理的碳锰硅钢板A53/A53M-01 无镀层热浸的、镀锌的、焊接的及无缝钢管的技术规范A539-99 天然气和燃料油管线用电阻焊钢盘管A540/A540M-00 特殊用途的合金钢螺栓材料A541/A541M-95(1999) 压力容器部件用经淬火和回火的碳素钢及合金钢锻件A542/A542M-99e1 压力容器用经回火和淬火的铬钼、铬钼钒及铬钼钒钛硼合金钢板A543/A543M-93(1999) 压力容器用经回火和淬火的镍铬钼合金钢板A550-78(2000) 铌铁合金A551-94(1999) 钢轮箍A553/A553M-95(2000) 压力容器用经回火和淬火的含8%及9%镍的合金钢板A554-98e1 焊接的无缝钢机械管A555/A555M-97 耐热不锈钢丝和盘条的通用要求A556/A556M-96 无缝冷拉碳素钢给水加热器管A560/A560M-93(1998) 铬镍合金铸件A561-71(1999) 工具钢棒的宏观刻蚀试验A562/A562M-90(2001) 搪玻璃或扩散金属镀层的压力容器用锰钛合金碳素钢板A563-00 碳合金钢螺母A563M-00 碳素钢及合金钢螺母技术规范（米制）A564/A564M-01 热轧及冷精轧时效硬化处理过的不锈钢棒材和型材技术规范A565-97 高温用马氏体不锈钢棒,锻件和锻制坯规格A568/A568M-00b 热轧及冷轧高强度低合金碳素钢薄板A571-84(1997) 适用于低温压力容器零件的奥氏体球墨铸铁件A571M-84(1997) 适用于低温压力容器零件的奥氏体球墨铸铁件(米制)A572/A572M-00a 高强度低合金钴钒结构钢技术规范A573/A573M-00a 增强韧性的结构碳素钢板A574-00 合金钢内六角螺钉A574M-00 合金钢内六角螺钉(米制)A575-96 商品级碳素钢棒(M级)A576-90b(2000) 特级热轧碳素钢棒A577/A577M-90(2001) 钢板的超声角波束检验A578/A578M-96(2001) 特殊设备用的普通钢板和包覆钢板的直波束超声探伤检验A579-99 超高强度合金钢锻件A580/A580M-98 耐热不锈钢丝A581/A581M-95b(2000) 高速切削用耐热不锈钢丝和盘条A582/A582M-95b(2000) 热轧或冷精轧的高速切削不锈及耐热钢棒A583-93(1999) 铁路用铸钢轮A584-97 镀铝钢丝编织栅栏网A585-97 镀铝刺钢丝A586-98 镀锌平行和螺旋形钢丝绳A587-96 化学工业用电阻焊低碳钢管A588/A588M-00a 高强度低合金结构钢4英寸(100mm)厚屈服点最小为50ksi(345MPa) A589-96 水井用无缝和焊接碳素钢管A591/A591M-98 薄镀层电解镀锌薄钢板A592/A592M-89(1999) 压力容器用经回火和淬火的高强度低合金钢锻制附件和零件A595-98 结构用圆锥形低碳钢管A596/A596M-95(1999) 用环形试验法和冲击法测定材料的直流磁性能的试验方法A597-87(1999) 铸造工具钢A598-92(1997) 磁放大器磁芯的磁性能测试法A599/A599M-99 锡制品，电解镀锡的冷滚轧薄板规范A6/A6M-01 轧制结构钢板材、型材和薄板桩通用技术要求A600-92a(1999) 高速工具钢A601-96(2000) 电解金属锰A602-94(1998) 汽车用可锻铸铁件A603-98 镀锌结构钢丝绳A604-93(1998) 自耗电极再溶化钢棒与钢坯的宏观腐蚀试验方法A606-98 改进防大气腐蚀性的热轧和冷轧高强度低合金钢薄板和带材A608-91a(1998) 高温受压离心铸造的铁铬镍高合金钢管A609/A609M-91(1997) 碳素钢,低合金钢和马氏体不锈钢铸件的超声波检测A610-79(2000) 尺寸测量用铁合金的取样和试验A611-00 冷轧优质碳素结构钢薄板A612/A612M-00 中温和低温压力容器用高强度碳素钢板A615/A615M-01a 钢筋混凝土配筋用变形和光面坯钢筋A618-01 热成型焊接与无缝高强度低合金结构钢管系A623-00 锡轧制产品A623M-00 镀锡薄钢板轧制品通用要求(米制)A624/A624M-98 锡辊轧制品.单压延电解马口铁A625/625M-98 一次轧制原钢板（未镀）和镀锡薄钢板轧制产品技术规范A626/A626M-98 二次压延电解镀锡厚钢板轧制品技术规范A626/A626M-98 锡轧制品.二次压延的电解镀锡板(米制)A627-95 安全设备用均质不易加工的钢棒A629-88(1994)e1 安全设备用不易加工的扁钢棒和型材A630-98 热浸电解镀锡板镀锡层重量测定的方法A632-01 通用无缝和焊接奥氏体不锈钢管(小直径)A633/A633M-00a 正火的高强度低合金结构钢A635/A635M-00 热轧碳素钢薄板,带材和重型粗盘条规格A636-76(2000) 氧化镍烧结块A638/A638M-00 高温用沉积硬化铁基超级合金棒,锻件及锻坯料A640-97 8字型缆吊架用镀锌钢丝绳A641/A641M-98 镀锌（电镀）碳素钢丝技术规范A644-98 铁铸件的相关术语A645/A645M-99a 压力容器用经特殊热处理的5%镍合金钢板A646-95(1999) 飞机及航空器锻件用优质合金钢大方坯及坯段A648-95(2000) 预应力混凝土管用冷拉钢丝A649/A649M-99 波纹纸机械用锻制钢辊规格A650/A650M-98 二次压延的锡轧黑板材A653/A653M-00 热浸处理的镀锌铁合金或镀锌合金薄钢板的标准规范A656/A656M-00a 具有改良可模锻性的高强度低合金热轧结构钢板A657/A657M-98a 一次和二次压延电解镀铬黑钢板轧制品技术规范A65-01 钢轨道钉A659/A659M-97 商业级热轧碳素钢薄板和带材(最大含碳量为0.16%-0.25%) A660-96 高温用离心铸造碳素钢管A662/A662M-99 中温和低温压力容器用锰碳钢板规格A663/A663M-89(2000) 商品级碳素钢棒的机械特性A664-99 在ASTM规范中对电工钢和层压钢级别的识别A666-00 退火或冷加工的奥氏体不锈钢薄板、带材、中厚板和扁棒A667/A667M-87(1998) 离心铸造的双金属(灰口及白口铸铁)圆柱体A668/A668M-96e1 一般工业用碳素钢和合金钢锻件A66-01 钢质螺旋道钉A671-96 常温和较低温用电熔焊钢管A672-96 中温高压用电熔焊钢管A673/A673M-95 结构钢冲击试验的取样程序A674-00 水或其它液体用球墨铸铁管的聚乙烯包装A675/A675M-90a(2000) 专用热轧碳素钢棒的机械特性A677/A677M-99 全处理型无取向电工钢A678/A678M-00a 结构用经回火和淬火的高强度低合金碳素钢板规格A679/A679M-00 硬(冷)拉高抗拉强度钢丝A67-00 热加工低碳钢和高碳钢垫板技术规范A681-94(1999) 合金工具钢A682/A682M-00 弹簧用冷轧高碳钢带材A683/A683M-99 半处理型无取向电工钢A684/A684M-99 冷轧高碳钢带材A686-92(1999) 碳素工具钢A688/A688M-01 焊接的奥氏体不锈钢给水加热器管A689-97 弹簧用碳素钢及合金钢棒A690/A690M-00a 在海洋环境中使用的高强度低合金工字形钢桩和薄板桩规格A691-98 高温下高压装置用电熔焊碳素钢和合金钢管A693-93(1999) 沉淀硬化耐热不锈钢板、薄板和带材A694/A694M-00 高压传输设备用碳素钢及合金钢管法兰、配件、阀门及零件用锻件A695-90b(1995)e1 流体动力设备专用热锻碳素钢棒A696-90a(2000) 压力管道部件专用热锻或冷精轧碳素钢棒A697-98 用伏特计、安培计和瓦特计法测定迭层铁芯样品的交流磁特性的试验方法A698/A698M-92(1997)e1 在弱交流磁场中磁屏蔽效率的试验方法A700-99e1 钢制品国内装运的包装、标记和装载方法A701-96(2000) 硅锰铁A702-89(2000) 热锻钢栅栏柱和组件A703/A703M-01 受压部件用钢铸件A704/A704M-96 混凝土加筋用焊接普通钢棒或杆的光面钢筋或钢筋网A705/A705M-95(2000) 时效硬化的不锈和耐热钢锻件A706/A706M-01 混凝土配筋用变形低合金光面无节钢筋A707/A707M-00a 低温设备用锻制碳素钢和合金钢法兰A709/A709M-01 桥梁用结构钢A710/A710M-00 低碳时效硬化的镍铜铬钼铌合金钢A711-92(1996)e1 钢锻件坯料A712-97 软磁性合金电阻率的测试方法A713-93(1998) 热处理部件用高碳弹簧钢丝A714-99 高强度低合金焊接钢管和无缝钢管A716-99 球墨铸铁涵洞管A717/A717M-95 单片样品表面绝缘电阻率的试验方法A719-97 磁性材料的叠装系数的试验方法A720-97 无取向电工钢延展性的试验方法A721-97 取向的电工钢的延展性试验方法A722/A722M-98 预应力混凝土用无涂覆的高强度钢筋A723/A723M-94(1999) 高强度压力元件用合金钢锻件A724/A724M-99 叠层焊接的压力容器用经淬火及回火的碳素钢压力容器板A726-00 半成品型冷轧磁性迭片级钢A727/A727M-00 具有固定切口韧性的管道部件用碳素钢锻件A729-93(1999) 货物运输及电气铁路用热处理合金钢轴A730-93(1999) 铁路用碳素钢及合金钢锻件A732/A732M-98 一般设备用熔模铸造碳素低合金钢及高强度加温钴合金钢铸件A733-99 焊接及无缝碳素钢和奥氏体不锈钢管接头A734/A734M-87a(1997) 经淬火和回火的合金钢与高强度低合金钢压力容器板A735/A735M-99 中温和低温用低碳锰钼钶合金钢压力容器板A736/A736M-88(2000) 低碳时效硬化的镍铜铬钼铌和镍铜锰钼铌合金钢压力容器板A737/A737M-99 高强度低合金钢压力容器板A738/A738M-00 中温和低温设备用经热处理的碳锰硅钢压力容器板A739-90a(2000) 升温或/和加压部件用热轧合金钢棒A740-98 钢丝网(编织或焊接电镀钢丝网)A741-98 公路护栏用镀锌钢丝绳和配件A742/A742M-98 波纹钢管用预涂聚合物和金属涂覆钢薄板A743/A743M-98ae1 一般用耐腐蚀铬铁及镍铬铁合金铸件A744/A744M-00 严酷条件下使用的耐腐蚀镍铬铁合金铸件A745/A745M-94(1999) 奥氏体钢锻件的超声波检验A746-99 排污管用球墨铸铁A747/A747M-99 沉淀硬化不锈钢铸件A748/A748M-87(1998) 压力容器用静态铸造的激冷白口铁-灰口铁双金属轧辊A749/A749M-97 热轧碳素钢和高强度低合金钢带材通用要求A74-98 铸铁污水管及配件的技术规范A750-77(1994)e1 阻挡区域用钢制通风格栅A751-96 钢制品化学分析的实验方法、操作和术语A752-93(1998) 合金钢条和粗圆钢丝A752M-93(1998) 合金钢条和粗圆钢丝(米制)A753-97 镍铁软磁合金A754/A754M-96(2000) X射线荧光涂层厚度的试验方法A755/A755M-99 外露建筑材料用热浸涂覆和用卷涂工艺预涂的钢薄板A756-94(2001) 耐磨不锈轴承钢A757/A757M-00 低温下承压设备及其它设备用铁素体和马氏体钢铸件A758/A758M-00 具有改进的切口韧性的对缝焊锻制碳素钢管配件A759-00 起重机用碳钢轨条A760/A760M-01 下水道和排水沟用金属涂覆的波纹钢管A761/A761M-98 现场栓接管、管拱和拱用波纹镀锌结构钢板A762/A762M-00 下水道和排水沟用预涂聚合物波纹钢管A763-93(1999)e1 铁素体不锈钢晶间腐蚀敏感性检测A764-95(2001) 机械弹簧用冷拉镀锌和按成品尺寸镀锌的碳素钢丝A765/A765M-98a 具有强制性韧性要求的碳素钢及低合金钢压力容器部件锻件A767/A767M-00b 钢筋混凝土用镀锌钢筋A768-95 涡轮机转子及轴用经真空处理的含铬12%的合金钢锻件A769/A769M-00 电阻焊钢结构型材A770/A770M-86(2001) 专用钢板通过厚度测量进行的抗拉试验A771/A771M-95(2001) 增殖反应堆堆芯部件用奥氏体不锈钢管A772/A772M-00 正弦电流用材料的交流磁导率的试验方法A773/A773M-96 用带直流电子的磁滞曲线记录仪的（B－H）回路法测量材料的磁性能的标准试验方法A774/A774M-00 低温和中温一般腐蚀情况下用的焊接锻制奥氏体不锈钢配件A775/A775M-01 涂环氧树脂的钢筋钢棒A778-01 焊接未退火的奥氏体不锈钢管形制品A779/A779M-00 预应力混凝土用应力消除未涂覆的密实七股钢丝绞绳A780-01 热浸镀锌层的损坏及无覆层区域的检修A781/A781M-00 一般工业用一般要求的钢和合金铸件A782/A782M-90(2001) 经淬火和回火的锰铬钼硅锆合金钢压力容器板A786/A786M-00b 轧制钢楼板A787-01 电阻焊金属涂覆碳素钢机械配管A788-98a 钢锻件A789/A789M-01 普通设备用无缝与焊接铁素体/奥氏体不锈钢管A790/A790M-01 无缝与焊接铁素体/奥氏体不锈钢管A792/A792M-99 热浸工艺法处理的55%铝-锌合金涂覆钢板A793-96 不锈钢轧制楼板A794-97 商品级冷轧碳素钢薄板(最高含碳量为0.16%-0.25%)A795-00 防火用黑色及热浸镀锌的焊接和无缝钢管A796/A796M-00 雨水管和卫生污水管及其它地下埋设管道用波纹钢管、管托架及拱形架结构设计惯例A798/A798M-01 下水道及其它类似用途用工厂制波纹钢管的安装A799/A799M-92(1997) 估算不锈钢铸件铁素体含量用仪表的校准A800/A800M-01 奥氏体合金钢铸件中铁素体含量的估算A801/A801M-99 铁钴高磁性饱和合金A802/A802M-95(2001) 钢铸件外观检验的表面验收标准A803/A803M-01 焊接铁素体不锈钢给水加热器管A804/A804M-99 在电力频率下用薄钢板型试样对材料交流磁特性的测试方法A805-93(1998) 冷轧碳素钢扁平线A807/A807M-97 下水道及其它类似用途用波纹结构钢涂覆管的安装A808/A808M-00a 具有改进的切口韧性的结构级高强度低合金碳钢、锰钢、铌钢和钒钢A809-98 镀铝碳素钢丝A810-00 镀锌钢管用绕网A811-97 粉末冶金技术制造的软磁铁零件A813/A813M-01 单或双焊接奥氏体不锈钢管A814/A814M-01 冷加工焊接奥氏体不锈钢管A815/A815M-01 锻制铁素体、铁素体/奥氏体和马氏体不锈钢管配件A817-00 链接栅栏网用金属涂覆钢丝A818-91(2001) 镀铜碳素钢丝A820-96 纤维增强混凝土用钢纤维A821/A821M-99 预应力混凝土容器用经回火的冷拉钢丝A822-90(2000) 液压系统设备用冷拉碳素无缝钢管A823-99 静铸永久铸模灰铸件A824-01 链接栅栏用Marcelled拉力金属涂覆钢丝A826/A826M-95(2001) 增殖反应堆堆芯部件用奥氏体和铁素体不锈钢管A827/A827M-93a(1998) 锻造及类似用途用的碳素钢板技术规范A829/A829M-00 结构性合金钢板A82-97ae1 钢筋混凝土用无节钢丝A830/A830M-00 按照化学成分要求提供的优质碳素钢板技术规范A831/A831M-95(2000) 核心部件用不锈耐热钢棒,坯段及锻件规格A832/A832M-99e1 压力容器板用铬钼钒及铬钼钒钛硼合金钢A833-84(1996) 用比较硬度测试仪测量金属材料的压痕硬性A834-95(2001) 一般工业用铁铸件的一般要求A835-84(2000) 铁合金与合金添加剂的筛分粒度A836/A836M-95b(2001) 搪瓷管和压力容器设备用钛稳定碳素体钢锻件A837-91(1996)e1 渗碳用合金钢锻件A838/A838M-97 继电器用易切削铁素体不锈软磁合金技术规范A839/A839M-96 软磁用途的磷铁粉末冶金制造的零件技术规范A840/A840M-00 全处理的磁性夹层钢A841/A841M-01 压力容器用温度机械控制工艺加工的钢板A842-85(1997) 高密度石墨铸铁A844/A844M-93(1999) 压力容器用直接淬火加工的含镍9%的合金钢板A845-85(2000) 用于脱氧与合金钢的钛碎片A846-85(2000) 用于脱氧与合金钢的铝碎片A847-99a 具有增强耐大气腐蚀性能的冷成型焊接与无缝高强度低合金结构管A848/A848M-96 低碳磁铁A849-00 波纹钢排水管和污水管用后涂覆铺面和衬里材料A851-96 高频感应焊接的未退火奥氏体钢冷凝器管A852/A852M-00a 最小屈服强度为70Ksi(485MPa),厚度为4英寸(100mm)的经淬火和回火的低合金结构钢板A853-93(1998) 普通碳素钢丝A854/A854M-98 镀锌高强度钢栅栏和格架用光滑金属线A855/A855M-98 锌-5%铝-铈合金涂覆的钢丝绳A856/A856M-98 锌-5%铝-铈合金涂覆的碳素钢丝A857/A857M-00a 冷成形轻型薄钢板桩A858/A858M-00 低温和腐蚀情况下用热处理碳素钢配件A859/A859M-95(1999) 压力容器部件用时效硬化镍铜铬钼钶低碳合金钢锻件A860/A860M-00 锻制高强度低合金钢的高强度对缝焊接配件A861-94e1 高硅铁管和配件A862/A862M-98 波纹钢污水管和排水管沥清(柏油)涂层的应用A865-97 钢管连接用黑色或镀锌焊接或无缝钢螺纹接头A866-94 耐磨中碳轴承钢A867/A867M-94(1998)e1 继电器用铁硅钢A871/A871M-00a 抗空气腐蚀的高强度低合金结构钢板。

ASTM美国材料标准中文版

ASTM美国材料标准中文版ASTM A488/A488-2007 钢铸件焊接工艺和人员资格评定的标准实施规程〔Standard Practice for Steel Castings, Welding, Qualifications of Procedures and Personnel〕ASTM A802/A 802M-1995(R2006重新审批) 视觉检测铸钢外表验收标准规程〔STANDARD PRACTICE FOR STEEL CASTINGS, SURFACE ACCEPTANCE STANDARDS, VISUAL EXAMINATION〕ASTM B108-2006 铝合金永久型铸件标准规〔STANDARD SPECIFICATION FOR ALUMINUM-ALLOY PERMANENT MOLD CASTINGS〕ASTM B179-2006 铸造用铝合金原锭及熔融锭在各铸造过程的标准技术规〔STANDARD SPECIFICATION FOR ALUMINUM ALLOYS IN INGOT AND MOLTEN FORMS FOR CASTINGS FROM ALL CASTING PROCESSES〕ASTM B26/B26M-2005 铝合金砂铸件标准规〔STANDARD SPECIFICATION FOR ALUMINUM-ALLOY SAND CASTINGS〕ASTM D256-2006 测定塑料抗悬臂梁摆锤冲击性的标准试验方法〔STANDARD TEST METHODS FOR DETERMINING THE IZOD PENDULUM IMPACT RESISTANCE OF PLASTICS〕ASTM D2794-1993(R2004) 有机涂层抗快速形变(冲击)作用的标准试验方法〔STANDARD TEST METHOD FOR RESISTANCE OF ORGANIC COATINGS TO THE EFFECTS OF RAPID DEFORMATION (IMPACT) 〕ASTM D3359-2008 胶带试验用测定粘合性的标准试验方法〔STANDARD TEST METHODS FOR MEASURING ADHESION BY TAPE TEST〕ASTM D3363-2005 铅笔试验法测定涂膜硬度的标准试验方法〔STANDARD TEST METHOD FOR FILM HARDNESS BY PENCIL TEST〕ASTM D4060-2007 用泰伯尔磨蚀机测定有机涂层耐磨性的标准试验方法〔STANDARD TEST METHOD FOR ABRASION RESISTANCE OF ORGANIC COATINGS BY THE TABER ABRASER〕ASTM D4674-2002A 暴露在室办公室环境下的塑料颜色稳定性加速试验的标准实施规〔STANDARD TEST METHOD FOR ACCELERATED TESTING FOR COLOR STABILITY OF PLASTICS EXPOSED TO INDOOR OFFICE ENVIRONMENTS〕ASTM D4752-2003 用溶剂擦试法测定硅酸乙酯(无机)富锌底漆耐甲乙酮的标准试验方法〔STANDARD TEST METHOD FOR MEASURING MEK RESISTANCE OF ETHYL SILICATE (INORGANIC) ZINC-RICH PRIMERS BY SOLVENT RUB〕ASTM D4828-1994E1(R2003) 有机覆层实际可洗性的标准试验方法〔STANDARD TEST METHODS FOR PRACTICAL WASHABILITY OF ORGANIC COATINGS〕ASTM D638-2003 塑料拉伸性能标准测试方法〔STANDARD TEST METHOD FOR TENSILE PROPERTIES OF PLASTICS〕ASTM E1316-2007 无损检测标准术语〔STANDARD TERMINOLOGY FOR NONDESTRUCTIVE EXAMINATIONS〕ASTM E1444-2005 磁粉检测标准规程〔STANDARD PRACTICE FOR MAGNETIC PARTICLE TESTING〕ASTM E155-2005 铝、镁铸件检验用标准参考射线底片〔STANDARD REFERENCE RADIOGRAPHS FOR INSPECTION OF ALUMINUM AND MAGNESIUM CASTINGS〕ASTM E165-2002 液体渗透剂检查标准测试方法〔STANDARD TEST METHOD FOR LIQUID PENETRANT EXAMINATION〕ASTM E165-2002 液体渗透检查的标准试验方法王倩译〔STANDARD TEST METHOD FOR LIQUID PENETRANT EXAMINATION〕ASTM E192-2004 航天设备蜡模钢铸件的参考放射线照相〔STANDARD REFERENCE RADIOGRAPHS OF INVESTMENT STEEL CASTINGS FOR AEROSPACE APPLICATIONS〕ASTM E242-2001(2005年重新批准) 在某些参数变化时射线图像外观用标准参考射线底片〔STANDARD REFERENCE RADIOGRAPHS FOR APPEARANCES OF RADIOGRAPHIC IMAGES AS CERTAIN PARAMETERS ARE CHANGED〕ASTM E385-2007 使用14兆电子伏特的中子活化和直接计数技术测定含氧量的试验方法〔STANDARD TEST METHOD FOR OXYGEN CONTENT USING A 14-MEV NEUTRON ACTIVATION AND DIRECT-COUNTING TECHNIQUE〕ASTM E426-1998(2007重新审批) 无缝及焊接收产品、沃斯田不锈钢及类似合金的电磁〔涡电流〕检测操作规程〔Standard Practice for Electromagnetic (Eddy-Current) Examination of Seamless and Welded Tubular Products, Austenitic Stainless Steel and Similar Alloys〕ASTM E446-98〔2004年重新批准〕用于厚度在2in(51mm)以下钢铸件的标准参考射线底片〔STANDARD REFERENCE RADIOGRAPHS FOR STEEL CASTINGS UP TO 2 IN. (51 MM) IN THICKNESS (ALSO SEE ASTM E 446 ADJUNCT SET, ASTM E 446 ADJUNCT V1, ASTM E 446 ADJUNCT V2. AND ASTM E 446 ADJUNCT V3)〕ASTM E466-2007 金属材料上进展的恒定振幅轴向疲劳试验〔STANDARD PRACTICE FOR CONDUCTING FORCE CONTROLLED CONSTANT AMPLITUDE AXIAL FATIGUE TESTS OF METALLIC MATERIALS 〕ASTM F2357-2004 使用NORMAN工具"RCA"磨擦器测定薄膜开关上墨水和涂层抗磨性的标准试验方法〔STANDARD TEST METHOD FOR DETERMINING THE ABRASION RESISTANCE OF INKS AND COATINGS ON MEMBRANE SWITCHES USING THE NORMAN TOOL "RCA" ABRADER〕ASTM G154-2006 非金属材料暴露用荧光灯紫外暴露装置的操作规标准〔STANDARD PRACTICE FOR OPERATING FLUORESCENT LIGHT APPARATUS FOR UVEXPOSURE OF NONMETALLIC MATERIALS〕ISO,ASME,ASTM,DIN, JIS 国外管道法兰用密封垫片标准汇编ASTM F36-1995? 测定垫片材料压缩率及回弹率的标准试验方法ASTM F37-1995? 垫片材料密封性的标准试验方法ASTM F38-1995? 垫片材料的蠕变松弛的标准试验方法ASTM F112-1995? 包覆垫片密封性能的标准试验方法ASTM F146-1995A? 垫片材料耐液体标准试验方法ASTM F363-1989(1994年重新确认) 垫片腐蚀试验的标准方法ASTM F336-1992? 用于腐蚀工况的非金属包覆垫片的设计与构造用标准方法ASTM F586-1979(1989年重新确认) 测定垫片汇漏(泄漏率与应力y和系数m的关系)的标准试验方法ASTM A6/A6M-2004 a版构造用轧制钢板、型钢、板桩和棒钢通用要求ASTM A27/A27M-2005版一般用途碳钢铸件标准技术条件ASTM A29/A29M-2005版热锻碳素钢和合金钢棒材一般要求标准规ASTM A36/A36M-2005版碳构造钢标准规ASTM A36/A36M-2004 碳构造钢标准规ASTM A48/A48M-2003版灰铸铁铸件标准技术条件ASTM A53/A53M-2005版无镀层及热浸镀锌焊接与无缝公称钢管标准技术条件ASTM A105/A105M-2005版管道部件用碳钢锻件ASTM A106-2006版高温用无缝碳钢公称管规ASTM A108-2003版冷精整的碳钢和合金钢棒材标准技术条件ASTM A123/A123M-2002版钢铁产品镀锌品层(热浸镀)标准规ASTM A126-2004版阀门、法兰和管道附件用灰铁铸件ASTM A143-2003版热浸镀锌构造钢制品防脆化的标准实施规程和催化探测方法ASTM A153/A153M-2005版钢铁构件镀锌层(热浸镀)标准规ASTM A179/A179M-1990a〔R2001〕版热交换器和冷凝器用无缝冷拉低碳钢管标准规ASTM A192-2002版高压设备用无缝碳钢锅炉管标准规ASTM A193/A193M-2006版高温用合金钢和不锈钢螺栓材料ASTM A194/A194M-2006版高温或高压或高温高压螺栓用碳钢及合金钢螺母标准规ASTM A209/A209M-2003版锅炉和过热器用无缝碳钼合金钢管标准规ASTM A210/A210M-2002版无缝中碳钢锅炉管和过热器管标准规ASTM A213/A213Mb-2004版无缝铁素体和奥氏体合金钢锅炉管、过热器管和换热器管标准规ASTM A216/A216M-2004版高温用可熔焊碳钢铸件标准规ASTM A234/A234M-2004版中、高温用锻制碳钢和合金钢管道配件ASTM A240/A240M-2005版压力容器用耐热铬及铬－镍不锈钢钢板、薄板和钢带标准技术条件ASTM A250/A250M-2004版锅炉和过热器用电阻焊铁素体碳合金钢管子标准技术条件ASTM A252-98〔R2002〕版焊接钢和无缝钢管桩的标准规ASTM A262-2002a版探测奥氏体不锈钢晶间腐蚀敏感度的标准实施规ASTM A269/A269-2004版通用无缝和焊接奥氏体不锈钢管标准规ASTM A276-2006版不锈钢棒材和型材标准规ASTM A283/A283M-2003版中、低抗拉强度碳素钢板标准技术条件ASTM A285/A285M-2003版压力容器用中、低抗拉强度碳素钢标准技术条件ASTM A307/A307M-2004版抗拉强度6000PSI碳钢螺栓和螺柱标准技术条件ASTM A312/A312M-2005版无缝和焊接的以及重度冷加工奥氏体不锈钢公称管标准技术条件ASTM A320/A320M-2005版低温用合金钢栓接材料标准规ASTM A333/A333M-2004版低温设备用无缝和焊接钢管的规标准ASTM A334/A334M-2004版低温设备用无缝和焊接碳素和合金钢管的标准规ASTM A335-2003版高温设备用无缝铁素体合金钢管标准规ASTM A336/A336M-2005版高温承压件合金钢锻件标准技术条件ASTM A350/A350M-2004a版需切口韧性试验的管道部件用碳钢和低合金钢锻件标准规ASTM A351/A351M-2006版承压件用奥氏体铸钢件标准规ASTM A352/A352M-2006版低温承压用铁素体和马氏体铸钢件标准规ASTM A356/A356M-2005版汽轮机用厚壁碳钢、低合金钢和不锈钢铸件标准技术条件ASTM A370-2005版钢制品力学性能试验方法和定义标准ASTM A387/A387M-2003版压力容器用铬钼合金钢板的标准规ASTM A403/A403M-2004版锻制奥氏体不锈钢管配件的标准规ASTM A450/A450M-2004版碳素钢管、铁素体合金钢管及奥氏体合金钢管一般要求的标准规ASTM A479/A479M-2005版锅炉和其他压力容器用不锈钢棒材和型材标准技术条件ASTM A484/A484M-2005版不锈钢棒材、钢坯及锻件通用要求标准技术条件ASTM A500-2003a版圆形与异型冷成型焊接与无缝碳素钢构造管标准规ASTM A515-2003版中温及高温压力容器用碳素钢板的标准规ASTM A516-2004a版中温及低温压力容器用碳素钢板的标准规ASTM A519-2003版机械工程用碳素钢和铝合金钢无缝钢管ASTM A530-2003版特种碳素钢和合金钢管一般要求的标准规ASTM A577/A577M-90(R2001〕版钢板超声斜射波检验ASTM A589/A589M-2006版打水井用碳素钢无缝钢管和焊接钢管ASTM A609/A609M-1991〔82002〕版碳钢、低合金钢和马氏体不锈钢铸件超声波检验ASTM A615/A615M-2004a版混凝土配筋用异形钢筋和无节钢胚棒标准规ASTM A703/A703M-2004版标准技术条件—承压件钢铸件通用要求ASTM A751-2001版钢制品化学分析方法，实验操作和术语ASTM A781/A781M-2004a版铸件、钢和合金的标准规及通用工业的一般性要求ASTM A788/A788M-2004a版标准技术条件—钢锻件通用要求ASTM A965/A965M-2002版高温承压件用奥氏体钢锻件标准规ASTM B16/B16M-2005版螺纹切削机用易车削黄铜棒、条和型材标准规ASTM B62/B62M-2002版青铜或高铜黄铜铸件标准规ASTM B209-2004版铝和铝合金薄板和中厚板标准规ASTM B462-2004版高温耐腐蚀用锻制或轧制的UNS NO6030、UNS NO6022、UNS NO6200、UNS NO8020、UNS NO8024、UNS NO8026、UNS NO8367、UNS NO10276、UNS N10665、UNS N10675和UNS R20033合金管法兰、锻制管件、阀门和零件标准规ASTM B564-2004版镍合金锻件标准规ASTM E6-2003版关于力学性能试验方法的标准术语ASTM E10-2001版金属材料布氏硬度的标准试验方法ASTM E18-2003版金属材料洛氏硬度和洛氏外表硬度的标准测试方法ASTM E29-2002版使用有效数字确定试验数据与规符合性作法ASTM E8M-2004版金属材料拉伸试验的标准测试方法ASTM E94-2004版放射性检查的标准指南ASTM E125-1963〔R2003〕版铁铸件的磁粉检验用标准参考照片ASTM E164-2003版焊件的超声接触检验的标准操作规程ASTM E208-1995a(R2000)版用导向落锤试验测定铁素体钢无塑性转变温度的标准试验方法ASTM E213-2004版金属管超声检验方法ASTM E273-2001版焊接公称管和管子制品超声波检验用标准实用规程ASTM E709-2001版磁粉试验的推荐试验方法ASTM F36-1999(R2003〕版测定垫片材料压缩率及回弹率的标准试验方法ASTM F37-2000版垫片材料密封性的标准试验方法ASTM F38-2000版垫片材料的蠕变松弛的标准试验方法ASTM F112-2000版包复垫片密封性能的标准试验方法ASTM F146-2004版垫片材料耐液体标准试验方法ASTM F1311-1990(R2001)版大口径组装式碳钢法兰标准规ASTM G1-2003版腐蚀试样的制备、清洁处理和评定用标准实施规ASTM G36-73(R1981) 参考资料标准实用规程：在沸的氯化镁溶液中进展的应力腐蚀裂纹试验ASTM G46-1976(R1986) 参考资料标准实用规程：麻点腐蚀的检验和评定ASTM G48-2003版使用三氯化铁溶液做不锈钢及其合金的耐麻点腐蚀和抗裂口腐蚀性试验的标准方法ASTM标准中译本丛书〔一〕碳钢、铸铁、不锈钢及合金钢材料标准规〔含18个标准)1. ASTM A105/A105M-2002版管道部件用碳钢锻件2. ASTM A126-1995(R2001)版阀门、法兰和管道附件用灰铁铸件3. ASTM A181/A181M-2001 版通用管路用碳钢锻件标准规4. ASTM A193/A193M-2001版?高温用合金钢和不锈钢螺栓材料5. ASTM A194/A194M-2001a版高温、高压或高温高压螺栓用碳钢及合金钢螺母标准规6. ASTM A216/A216M-2001a版高温用可熔焊碳钢铸件标准规7. ASTM A217/A217M-2002 版高温承压件用马氏体不锈钢和合金钢铸件标准规8. ASTM A276-2002a版不锈钢棒材和型材9. ASTM A278/A278M-2001版高温不超过650°F〔350℃〕的承压部件用灰铸铁件10. ASTM A320/A320M-2002 版低温用合金钢栓接材料11. ASTM A350/A350M-2002 版要求冲击韧性试验的管件用碳钢及低合金钢锻件标准规12. ASTM A351/A351M-2000 版承压件用奥氏体、奥氏体-铁素体〔双相〕钢铸件规13. ASTM A352/A352M-1993(R1998)版低温承压件用铁素体和马氏体钢铸件标准规14. ASTM A395/A395M-1999 版高温用铁素体球墨铸铁承压铸件15. ASTM A439-1983(R1999)版奥氏体球墨铸铁件16. ASTM A536-1984(R1999)版球墨铸铁件17. ASTM A694/A694M-2000? 版高温输送用管法兰、管件、阀门及零件用碳钢和合金钢锻件标准规18. ASTM A965/A965M-2002 版高温高压部件用奥氏体钢锻件ASTM标准中译本丛书〔二〕法兰、管件、阀门及部件〔含9个标准〕1. ASTM A182/A182M-2002版高温用锻制或轧制合金钢法兰、锻制管件、阀门和部件2. ASTM A961-2002版管道用钢制法兰、锻制管件、阀门和零件的通用要求标准规3. ASTM B462-2002版高温耐腐蚀用锻制或轧制的UNS NO6030、UNS NO6022、UNS NO6200、UNS NO8020、UNS NO8024、UNS NO8026、UNS NO8367、UNS NO10276、UNS N10665、UNS N10675和UNS R20033合金管法兰、锻制管件、阀门和零件标准规4. ASTM F885-1984〔R2002〕版公称管径为NPS 1/4～2的青铜截止阀外形尺寸标准规5. ASTM F992-1986(R2001)版阀门铭牌标准规6. ASTM F993-1986(R2001)版阀门锁紧装置标准规7. ASTM F1030-1986(R1998)版阀门操作装置的选择准那么8. ASTM F1098-1987(R1998)版公称管径有NPS2～24的蝶阀外形尺寸标准规9. ASTM F1565-2000版蒸汽用减压阀规。

ASTM-A标准(中文)

AA1000-99 弹簧专用碳钢和合金钢钢丝标准A1001-99 大型材高强度钢铸件标准A1002-99 镍铝类合金铸件标准A100-93(2000) 硅铁A101-93(2000) 铬铁A102-93(2000) 钒铁合金A105/A105M-01 管系部件用碳素钢锻件A106-999e1 高温用无缝碳素钢管A108-99 优质冷加工碳素钢棒材技术标准A109/A109M-00e1 冷轧碳素钢带技术标准A111-99a 和电报线路用镀锌"铁"丝规格A116-00 镀锌钢丝编织栏栅网A121-99 镀锌刺钢丝A123/A123M-00 钢铁产品的锌镀层〔热浸镀锌〕技术标准A125-96 热处理螺旋形钢弹簧A126-95(2001) 阀门、法兰和管配件用灰铁铸件A128/A128M-93(1998) 钢铸件,奥氏体锰A131/A131M-94 海船用结构钢A132-89(2000) 钼铁合金A134-96 电熔(电弧)焊钢管(NPS为16英寸和16英寸以上)A135-01 电阻焊钢管A139-00 电熔(电弧)焊钢管(4英寸以上的)A143-74(1999) 热浸镀锌结构钢制品防脆裂措施和探测脆裂的程序A146-64(2000) 氧化钼制品A148/A148M-01 结构用高强度钢铸件A153/A153M-00 钢铁制金属构件上镀锌层(热浸)A159-83(2001) 汽车用灰铁铸件A167-99 不锈钢和耐热铬镍钢板、薄板及带材A176-99 不锈钢和耐热铬钢板、薄板及带材A178/A178M-95(2000) 电阻焊接碳素钢钢管及碳锰钢锅炉和过热器管的技术标准A179/A179M-90a(1996)e1 热交换器和冷凝器用无缝冷拉低碳钢管A181/A181M-01 普通锻制碳素钢管的规格A182/A182M-01 高温设备用锻制或轧制的合金钢管法兰、锻制管件、阀门及零件A183-98 钢轨用碳素钢螺栓和螺母A184/A184M-01 混凝土加筋用变形钢筋编织网A185-97 钢筋混凝土用焊接钢丝结构A1-00 碳素钢丁字轨A192/A192M-91(1996)e1 高压用无缝碳素钢锅炉管A193/A193M-01 高温设备用合金钢和不锈钢螺栓材料A194/A194M-01 高温和高压设备用碳素钢与合金钢螺栓和螺母的规格A197/A197M-00 化铁炉用可锻铸铁A20/A20M-01 压力容器用钢板材通用要求A202/A202M-93(1999) 压力容器用铬锰硅合金钢板A203/A203M-97 压力容器用镍合金钢板A204/A204M-93(1999) 压力容器用钼合金钢板A209/A209M-98 锅炉和过热器用无缝碳钼合金钢管A210/A210M-96 锅炉和过热器用无缝中碳素管A213/A213M-01 无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管A214/A214M-96 热交换器与冷凝器用电阻焊接碳素钢管A216/A216M-93(1998) 高温下使用的适合于熔焊的碳素钢铸件规格A217/A217M-01 适合高温受压零件用合金钢和马氏体不锈钢铸件A21-94(1999) 铁路用未经热处理和经热处理的碳素钢轴A220/A220M-99 珠光体可锻铁A225/A225M-93(1999) 压力容器用锰矾镍合金钢板A227/A227M-99 机械弹簧用冷拉钢丝A228/A228M-00 乐器用优质弹簧钢丝A229/A229M-99 机械弹簧用油回火的钢丝A230/A230M-99 阀门用油回火优质碳素钢弹簧丝A231/A231M-96 铬钒合金钢弹簧丝A232/A232M-99 阀门用优质铬钒合金钢弹簧丝A234/A234M-00a 中温与高温下使用的锻制碳素钢及合金钢管配件A239-95(1999) 用普力斯试验法(硫酸铜浸蚀)确定铁或钢制品上镀锌层最薄点的测试方法A240/A240M-01 压力容器用耐热铬及铬镍不锈钢板、薄板及带材A242/A242M-00a 高强度低合金结构钢A247-67(1998) 铁铸件中石墨显微结构评定试验方法A249/A249M-01 锅炉、过热器、换热器和冷凝器用焊接奥氏体钢管A250/A250M-95(2001) 锅炉和过热器用电阻焊铁素体合金钢管A252-98e1 焊接钢和无缝钢管桩A254-97 铜焊钢管规格A255-99 测定钢淬透性用末端淬火试验的标准试验方法A262-98 奥氏体不锈钢晶间浸蚀敏感性的检测A263-94a(1999) 耐腐蚀铬钢包覆板材,薄板材及带材技术标准A264-94a(1999) 包覆的不锈铬镍钢板,薄板及带材规格A265-94a(1999) 镍和镍基合金包覆钢板规格A266/A266M-99 压力容器部件用碳素钢锻件规格A268/A268M-01 一般设备用无缝和焊接铁素体与马氏体不锈钢管A269-01 一般设备用无缝和焊接奥氏体不锈钢管A27/A27M-95(2000) 通用碳素钢铸件A270-01 卫生设施用无缝钢和焊接奥氏体不锈钢管A275/A275M-98 钢锻件的磁粉检查试验方法A276-00a 不锈钢棒材和型材A278-93 适用于650F容压部件用灰铸铁件的技术标准A283/A283M-00 低和中等抗拉强度碳素钢板A285/A285M-90(2001) 压力容器用低和中等抗拉强度的碳素钢板A288-91(1998) 涡轮发电机磁性定位环用碳素钢和合金钢锻件A289/A289M-97 发电机非磁性定位环用合金钢锻件的技术标准A29/A29M-99e1 热锻及冷加工碳素钢和合金钢棒A2-90(1997) 普通型,带槽和防护型碳素工字钢轨A290-95(1999) 减速器环用碳素钢和合金钢锻件A291-95(1999) 减速器小齿轮、齿轮和心轴用碳素钢和合金钢锻件A295-98 高碳耐磨轴承钢技术标准A297/A297M-97(1998) 一般用耐热铬铁与镍铬铁合金钢铸件规格A299/A299M-97e1 压力容器用锰硅碳钢板A302/A302M-97e1 压力容器用锰钼和锰钼镍合金钢板A304-96 有末端淬火淬透性要求的合金钢棒材的技术标准A307-00 抗拉强度为60000psi的碳素钢螺栓和螺柱的技术标准A308-99 经热浸处理镀有铅锡合金的薄板材的技术标准A309-94a(1999) 用三点试验法测定长镀锌薄钢板镀层的重量成分的试验方法A311/A311M-95(2000) 有机械性能要求的消除应力的冷拉碳素钢棒A312/A312M-00c 无缝和焊接奥氏体不锈钢管A313/A313M-98 不锈钢弹簧丝技术标准A314-97 锻造用不锈及耐热钢坯及钢棒规格A31-00 钢铆钉及铆钉和压力容器用棒材A319-71(2001) 高温无压部件用灰铁铸件A320/A320M-01 低温用合金钢螺栓材料规格A321-90(1995)e1 经淬火和回火的碳素钢棒A322-91(1996) 合金钢棒材.级别A323-93(2000) 硼铁规格A324-73(2000) 钛铁合金A325-00 经热处理最小抗拉强度为120/105ksi的钢结构螺栓A325M-00 结构钢连接件用高强度螺栓(米制)A327-91(1997) 铸铁冲击试验方法A327M-91(1997) 铸铁冲击试验方法(米制)A328/A328M-00 薄钢板桩A331-95(2000) 冷加工合金钢棒A333/A333M-99 低温用无缝与焊接钢管规格A334/A334M-99 低温设备用无缝与焊接碳素和合金钢管A335/A335M-01 高温用无缝铁素体合金钢管A336/A336M-99e1 压力与高温部件用合金钢锻件规格A338-84(1998) 铁路,船舶和其他重型装备在温度到达650华氏度(345摄氏度)时使用的可锻铸铁法兰,管件和阀门零件A34/A34M-96 磁性材料的抽样和采购试验的标准惯例A340-99a 有关磁性试验用符号和定义的术语A341/A341M-00 用直流磁导计和冲击试验法测定材料的直流磁性能的试验方法A342/A342M-99 磁铁材料导磁率的试验方法A343-97 在电力频率下用瓦特计-安培计-伏特计法(100-1000赫兹)和25 厘米艾普斯亭(EPSTEIN) 机架测定材料的交流电磁性能的试验方法A345-98 磁设备用平轧电炉钢A348/A348M-00 用瓦特计--安培计--伏特计法(100-10000赫兹)和25厘米艾普斯亭框测定材料的交流磁性能的试验方法A350/A350M-00c 要求进行缺口韧性试验的管道部件用碳素钢与低合金钢锻件技术标准A351/A351M-00 容压零件用奥氏体及奥氏体铁素体铸铁的技术标准A352/A352M-93(1998) 低温受压零件用铁素体和马氏体钢铸件规格A353/A353M-93(1999) 压力容器用经二次正火及回火处理的含9％镍的合金钢板A354-01 淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格A355-89(2000) 渗氮用合金钢棒A356/A356M-98e1 蒸汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件A358/A358M-01 高温用电熔焊奥氏体铬镍合金钢管A36/A36M-00a 碳素结构钢技术标准A363-98 地面架空线用镀锌钢丝绳A367-60(1999) 铸铁的激冷试验方法A368-95a(2000) 不锈钢和耐热钢丝绳的标准A369/A369M-01 高温用锻制和镗孔碳素钢管和铁素体合金钢管A370-97a 钢制品机械测试的标准试验方法和定义A372/A372M-99 薄壁压力容器用碳素钢及合金钢锻件A376/A376M-01 高温中心站用无缝奥氏钢管A377-99 球墨铸铁压力管标准索引A380-99e1 不锈钢零件、设备和系统的清洗和除垢A381-96 高压输送用金属弧焊钢管A384-76(1996) 防止钢组件热浸镀锌时翘曲和扭曲用平安保护A385-00 提供高质量镀锌覆层(热浸)A3-01 低、中、高碳素钢鱼尾〔连接〕板A387/A387M-99e1 压力容器用铬钼合金钢板A388/A388M-95(2000)e1 重型钢锻件超声波检测A389/A389M-93(1998) 适合高温受压部件用经特殊热处理的合金钢铸件规格A390-95(2001) 饲养家禽用镀锌钢丝栏栅网(六角形和直线形)A391/A391M-98 80号合金钢链条A392-96 镀锌钢丝链环栏栅网A394-00 传动塔架用镀锌和裸露钢螺栓A395/A395M-99 高温用铁素体球墨铸铁受压铸件A400-69(2000) 钢棒的成分及机械性能选择指南A401/A401M-98 铬硅合金钢丝A403/A403M-00b 锻制奥氏体不锈钢管配件A407-93(1998) 盘簧用冷拉钢丝A409/A409M-01 腐蚀场所或高温下使用的焊接大口径奥氏体钢管A411-98 镀锌低碳钢铠装线A413/A413M-00 碳素钢链A414/A414M-00 压力容器用碳素薄钢板A416/A416M-99 预应力混凝土用无涂层七股钢铰线A417-93(1998) 之字型、方型和正弦型装垫弹簧元件用冷拉钢丝A418-99 涡轮机及发电机钢转子锻件的超声波检查方法A420/A420M-00b 低温下用锻制碳素钢和合金钢管配件A421/A421M-98a 预应力混凝土用无涂层消除应力钢丝的技术标准A423/A423M-95(2000) 无缝和电焊低合金钢管A424-00 搪瓷用钢薄板A426-92(1997) 高温用离心铸造的铁素体合金钢管A427-74(1996)e1 冷轧和热轧用锻制合金钢辊A428/A428M-01 钢铁制品上铝覆层重量的测试方法A434-90a(2000) 热轧与冷精轧经回火及淬火的合金钢棒A435/A435M-90(2001) 钢板的直射束纵向超声波检验A436-84(1997)e1 奥氏体灰口铁铸件A437/A437M-01 高温用经特殊处理的涡轮型合金钢螺栓材料A438-80(1997) 灰铸铁横向弯曲试验A439-83(1999) 奥氏体可锻铸铁铸件A447/A447M-93(1998) 高温用镍铬铁合金钢铸件(25-12级)A449-00 经淬火和回火的钢螺栓和螺柱A450/A450M-96a 碳素钢管、铁素体合金钢管及奥氏体合金钢管A451-93(1997) 高温用离心铸造的奥氏体钢管A453/A453M-00 具有同奥氏体钢相类似的膨胀系数、屈服强度为50-120Ksi(345-827MPa)的耐高温螺栓材料A455/A455M-90(2001) 压力容器用高强度碳锰钢板A456/A456M-99 大型曲轴锻件的磁粉检查A459-97 镀锌平轧扁钢铠装带A460-94(1999) 包铜钢丝绳标准A463/A463M-00 热浸镀铝薄钢板A466/A466M-98 非焊接碳素钢链A467/A467M-98 机器链和盘旋链A469-94a(1999) 用于发电机转子的真空处理钢锻件A470-01 涡轮机转子和轴用经真空处理的碳素钢和合金锻件A471-94(1999) 涡轮转子转盘和转轮用真空处理合金钢锻件技术标准A472-98 蒸汽涡轮机轴及转子锻件的热稳定性的试验方法A473-01 不锈和耐热钢锻件A474-98 包铝钢丝绳标准A475-98 镀锌钢丝绳A476/A476M-00 造纸厂枯燥辊用球墨可锻铸铁件A478-97 铬镍不锈钢和耐热钢制编织钢丝A479/A479M-00 锅炉及压力容器用不锈钢和耐热钢棒与型材A47/A47M-99 铁素体可锻铁铸件A480/A480M-01 扁平轧制耐热不锈钢厚板材、薄板材和带材通用要求A481-94(2000) 金属铬A482-93(2000) 铬铁硅A483-64(2000) 硅锰合金A484/A484M-00 不锈及耐热锻钢棒,钢坯及锻件的规格A485-00 高淬透性耐磨轴承钢的技术标准A487/A487M-93(1998) 受压钢铸件A488/A488M-01 钢铸件焊接规程和工作人员的合格鉴定A48-94ae1 灰铁铸件A489-00 碳素钢吊耳A490-00 最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓A491-96 镀铝钢链环栏栅结构A492-95(2000) 耐热不锈钢丝绳A493-95(2000) 冷镦和冷锻不锈钢和耐热钢丝A494/A494M-00 镍和镍合金铸件A495-94(2000) 硅钙合金钢技术标准A496-97ae1 钢筋混凝土用变形钢丝A497-99e1 钢筋混凝土用焊接变形钢丝网A498-98 无缝与焊接碳素钢,铁素体钢与奥氏体钢制有整体散热片的换热器钢管A49-01 经热处理的碳素钢鱼尾〔连接〕板，微合金鱼尾板及锻制碳素钢异型鱼尾板A499-89(1997)e1 轧制丁字钢轨用的碳素钢棒材及型材的技术标准A500-01 圆形与异型焊接与无缝碳素钢结构管A501-01 热成型焊接与无缝碳素钢结构管A503/A503M-01 锻制大型曲轴的超声波检验A504-93(1999) 锻制碳素钢轮A505-00 热轧和冷轧合金钢薄板和带材A506-00 正规质量及优质结构的热轧和冷轧合金钢薄板与带材A507-00 优质拉拔,热轧和冷轧合金钢薄板与带材A508/A508M-95(1999) 压力容器用经回火和淬火真空处理的碳素钢与合金钢锻件A510-00 碳素钢盘条和粗圆钢丝通用要求A510M-00 碳素钢盘条和粗圆钢丝(米制)A511-96 无缝不锈钢机械管A512-96 冷拉对缝焊碳素钢机械管A513-00 电阻焊碳素钢与合金钢机械钢管A514/A514M-00a 焊接用经回火与淬火的高屈服强度合金钢板A515/A515M-92(1997) 中温及高温压力容器用碳素钢板A516/A516M-90(2001) 中温及低温压力容器用碳素钢板A517/A517M-93(1999) 压力容器用经回火与淬火的高强度合金钢板A518/A518M-99 耐蚀高硅铁铸件A519-96 无缝碳素钢与合金钢机械管A521-96 一般工业用闭式模钢锻件A522/A522M-95b(2000) 低温用锻制或轧制含镍8%和9%的合金钢法兰,配件,阀门和零件规格A523-96 高压管型电缆线路用平端无缝与电阻焊钢管A524-96 常温和低温用无缝碳素钢管A529/A529M-00 高强度碳锰结构钢质量A530/A530M-99e1 特种碳素钢和合金钢管A531/A531M-91(1996) 涡轮发电机钢定位环的超声波检验A532/A532M-93a(1999)e1 耐磨铸铁A533/A533M-93(1999) 压力容器用经回火和淬火的锰钼及锰钼镍合金钢板A534-94 用于耐摩擦轴承的渗碳钢A536-84(1999)e1 球墨铸铁件A537/A537M-95(2000) 压力容器用经热处理的碳锰硅钢板A53/A53M-01 无镀层热浸的、镀锌的、焊接的及无缝钢管的技术标准A539-99 天然气和燃料油管线用电阻焊钢盘管A540/A540M-00 特殊用途的合金钢螺栓材料A541/A541M-95(1999) 压力容器部件用经淬火和回火的碳素钢及合金钢锻件A542/A542M-99e1 压力容器用经回火和淬火的铬钼、铬钼钒及铬钼钒钛硼合金钢板A543/A543M-93(1999) 压力容器用经回火和淬火的镍铬钼合金钢板A550-78(2000) 铌铁合金A551-94(1999) 钢轮箍A553/A553M-95(2000) 压力容器用经回火和淬火的含8%及9%镍的合金钢板A554-98e1 焊接的无缝钢机械管A555/A555M-97 耐热不锈钢丝和盘条的通用要求A556/A556M-96 无缝冷拉碳素钢给水加热器管A560/A560M-93(1998) 铬镍合金铸件A561-71(1999) 工具钢棒的宏观刻蚀试验A562/A562M-90(2001) 搪玻璃或扩散金属镀层的压力容器用锰钛合金碳素钢板A563-00 碳合金钢螺母A563M-00 碳素钢及合金钢螺母技术标准〔米制〕A564/A564M-01 热轧及冷精轧时效硬化处理过的不锈钢棒材和型材技术标准A565-97 高温用马氏体不锈钢棒,锻件和锻制坯规格A568/A568M-00b 热轧及冷轧高强度低合金碳素钢薄板A571-84(1997) 适用于低温压力容器零件的奥氏体球墨铸铁件A571M-84(1997) 适用于低温压力容器零件的奥氏体球墨铸铁件(米制)A572/A572M-00a 高强度低合金钴钒结构钢技术标准A573/A573M-00a 增强韧性的结构碳素钢板A574-00 合金钢内六角螺钉A574M-00 合金钢内六角螺钉(米制)A575-96 商品级碳素钢棒(M级)A576-90b(2000) 特级热轧碳素钢棒A577/A577M-90(2001) 钢板的超声角波束检验A578/A578M-96(2001) 特殊设备用的普通钢板和包覆钢板的直波束超声探伤检验A579-99 超高强度合金钢锻件A580/A580M-98 耐热不锈钢丝A581/A581M-95b(2000) 高速切削用耐热不锈钢丝和盘条A582/A582M-95b(2000) 热轧或冷精轧的高速切削不锈及耐热钢棒A583-93(1999) 铁路用铸钢轮A584-97 镀铝钢丝编织栅栏网A585-97 镀铝刺钢丝A586-98 镀锌平行和螺旋形钢丝绳A587-96 化学工业用电阻焊低碳钢管A588/A588M-00a 高强度低合金结构钢4英寸(100mm)厚屈服点最小为50ksi(345MPa) A589-96 水井用无缝和焊接碳素钢管A591/A591M-98 薄镀层电解镀锌薄钢板A592/A592M-89(1999) 压力容器用经回火和淬火的高强度低合金钢锻制附件和零件A595-98 结构用圆锥形低碳钢管A596/A596M-95(1999) 用环形试验法和冲击法测定材料的直流磁性能的试验方法A597-87(1999) 铸造工具钢A598-92(1997) 磁放大器磁芯的磁性能测试法A599/A599M-99 锡制品，电解镀锡的冷滚轧薄板标准A6/A6M-01 轧制结构钢板材、型材和薄板桩通用技术要求A600-92a(1999) 高速工具钢A601-96(2000) 电解金属锰A602-94(1998) 汽车用可锻铸铁件A603-98 镀锌结构钢丝绳A604-93(1998) 自耗电极再溶化钢棒与钢坯的宏观腐蚀试验方法A606-98 改良防大气腐蚀性的热轧和冷轧高强度低合金钢薄板和带材A608-91a(1998) 高温受压离心铸造的铁铬镍高合金钢管A609/A609M-91(1997) 碳素钢,低合金钢和马氏体不锈钢铸件的超声波检测A610-79(2000) 尺寸测量用铁合金的取样和试验A611-00 冷轧优质碳素结构钢薄板A612/A612M-00 中温和低温压力容器用高强度碳素钢板A615/A615M-01a 钢筋混凝土配筋用变形和光面坯钢筋A618-01 热成型焊接与无缝高强度低合金结构钢管系A623-00 锡轧制产品A623M-00 镀锡薄钢板轧制品通用要求(米制)A624/A624M-98 锡辊轧制品.单压延电解马口铁A625/625M-98 一次轧制原钢板〔未镀〕和镀锡薄钢板轧制产品技术标准A626/A626M-98 二次压延电解镀锡厚钢板轧制品技术标准A626/A626M-98 锡轧制品.二次压延的电解镀锡板(米制)A627-95 平安设备用均质不易加工的钢棒A629-88(1994)e1 平安设备用不易加工的扁钢棒和型材A630-98 热浸电解镀锡板镀锡层重量测定的方法A632-01 通用无缝和焊接奥氏体不锈钢管(小直径)A633/A633M-00a 正火的高强度低合金结构钢A635/A635M-00 热轧碳素钢薄板,带材和重型粗盘条规格A636-76(2000) 氧化镍烧结块A638/A638M-00 高温用沉积硬化铁基超级合金棒,锻件及锻坯料A640-97 8字型缆吊架用镀锌钢丝绳A641/A641M-98 镀锌〔电镀〕碳素钢丝技术标准A644-98 铁铸件的相关术语A645/A645M-99a 压力容器用经特殊热处理的5%镍合金钢板A646-95(1999) 飞机及航空器锻件用优质合金钢大方坯及坯段A648-95(2000) 预应力混凝土管用冷拉钢丝A649/A649M-99 波纹纸机械用锻制钢辊规格A650/A650M-98 二次压延的锡轧黑板材A653/A653M-00 热浸处理的镀锌铁合金或镀锌合金薄钢板的标准标准A656/A656M-00a 具有改良可模锻性的高强度低合金热轧结构钢板A657/A657M-98a 一次和二次压延电解镀铬黑钢板轧制品技术标准A65-01 钢轨道钉A659/A659M-97 商业级热轧碳素钢薄板和带材(最大含碳量为0.16%-0.25%) A660-96 高温用离心铸造碳素钢管A662/A662M-99 中温和低温压力容器用锰碳钢板规格A663/A663M-89(2000) 商品级碳素钢棒的机械特性A664-99 在ASTM标准中对电工钢和层压钢级别的识别A666-00 退火或冷加工的奥氏体不锈钢薄板、带材、中厚板和扁棒A667/A667M-87(1998) 离心铸造的双金属(灰口及白口铸铁)圆柱体A668/A668M-96e1 一般工业用碳素钢和合金钢锻件A66-01 钢质螺旋道钉A671-96 常温和较低温用电熔焊钢管A672-96 中温高压用电熔焊钢管A673/A673M-95 结构钢冲击试验的取样程序A674-00 水或其它液体用球墨铸铁管的聚乙烯包装A675/A675M-90a(2000) 专用热轧碳素钢棒的机械特性A677/A677M-99 全处理型无取向电工钢A678/A678M-00a 结构用经回火和淬火的高强度低合金碳素钢板规格A679/A679M-00 硬(冷)拉高抗拉强度钢丝A67-00 热加工低碳钢和高碳钢垫板技术标准A681-94(1999) 合金工具钢A682/A682M-00 弹簧用冷轧高碳钢带材A683/A683M-99 半处理型无取向电工钢A684/A684M-99 冷轧高碳钢带材A686-92(1999) 碳素工具钢A688/A688M-01 焊接的奥氏体不锈钢给水加热器管A689-97 弹簧用碳素钢及合金钢棒A690/A690M-00a 在海洋环境中使用的高强度低合金工字形钢桩和薄板桩规格A691-98 高温下高压装置用电熔焊碳素钢和合金钢管A693-93(1999) 沉淀硬化耐热不锈钢板、薄板和带材A694/A694M-00 高压传输设备用碳素钢及合金钢管法兰、配件、阀门及零件用锻件A695-90b(1995)e1 流体动力设备专用热锻碳素钢棒A696-90a(2000) 压力管道部件专用热锻或冷精轧碳素钢棒A697-98 用伏特计、安培计和瓦特计法测定迭层铁芯样品的交流磁特性的试验方法A698/A698M-92(1997)e1 在弱交流磁场中磁屏蔽效率的试验方法A700-99e1 钢制品国内装运的包装、标记和装载方法A701-96(2000) 硅锰铁A702-89(2000) 热锻钢栅栏柱和组件A703/A703M-01 受压部件用钢铸件A704/A704M-96 混凝土加筋用焊接普通钢棒或杆的光面钢筋或钢筋网A705/A705M-95(2000) 时效硬化的不锈和耐热钢锻件A706/A706M-01 混凝土配筋用变形低合金光面无节钢筋A707/A707M-00a 低温设备用锻制碳素钢和合金钢法兰A709/A709M-01 桥梁用结构钢A710/A710M-00 低碳时效硬化的镍铜铬钼铌合金钢A711-92(1996)e1 钢锻件坯料A712-97 软磁性合金电阻率的测试方法A713-93(1998) 热处理部件用高碳弹簧钢丝A714-99 高强度低合金焊接钢管和无缝钢管A716-99 球墨铸铁涵洞管A717/A717M-95 单片样品外表绝缘电阻率的试验方法A719-97 磁性材料的叠装系数的试验方法A720-97 无取向电工钢延展性的试验方法A721-97 取向的电工钢的延展性试验方法A722/A722M-98 预应力混凝土用无涂覆的高强度钢筋A723/A723M-94(1999) 高强度压力元件用合金钢锻件A724/A724M-99 叠层焊接的压力容器用经淬火及回火的碳素钢压力容器板A726-00 半成品型冷轧磁性迭片级钢A727/A727M-00 具有固定切口韧性的管道部件用碳素钢锻件A729-93(1999) 货物运输及电气铁路用热处理合金钢轴A730-93(1999) 铁路用碳素钢及合金钢锻件A732/A732M-98 一般设备用熔模铸造碳素低合金钢及高强度加温钴合金钢铸件A733-99 焊接及无缝碳素钢和奥氏体不锈钢管接头A734/A734M-87a(1997) 经淬火和回火的合金钢与高强度低合金钢压力容器板A735/A735M-99 中温和低温用低碳锰钼钶合金钢压力容器板A736/A736M-88(2000) 低碳时效硬化的镍铜铬钼铌和镍铜锰钼铌合金钢压力容器板A737/A737M-99 高强度低合金钢压力容器板A738/A738M-00 中温和低温设备用经热处理的碳锰硅钢压力容器板A739-90a(2000) 升温或/和加压部件用热轧合金钢棒A740-98 钢丝网(编织或焊接电镀钢丝网)A741-98 公路护栏用镀锌钢丝绳和配件A742/A742M-98 波纹钢管用预涂聚合物和金属涂覆钢薄板A743/A743M-98ae1 一般用耐腐蚀铬铁及镍铬铁合金铸件A744/A744M-00 严酷条件下使用的耐腐蚀镍铬铁合金铸件A745/A745M-94(1999) 奥氏体钢锻件的超声波检验A746-99 排污管用球墨铸铁A747/A747M-99 沉淀硬化不锈钢铸件A748/A748M-87(1998) 压力容器用静态铸造的激冷白口铁-灰口铁双金属轧辊A749/A749M-97 热轧碳素钢和高强度低合金钢带材通用要求A74-98 铸铁污水管及配件的技术标准A750-77(1994)e1 阻挡区域用钢制通风格栅A751-96 钢制品化学分析的实验方法、操作和术语A752-93(1998) 合金钢条和粗圆钢丝A752M-93(1998) 合金钢条和粗圆钢丝(米制)A753-97 镍铁软磁合金A754/A754M-96(2000) X射线荧光涂层厚度的试验方法A755/A755M-99 外露建筑材料用热浸涂覆和用卷涂工艺预涂的钢薄板A756-94(2001) 耐磨不锈轴承钢A757/A757M-00 低温下承压设备及其它设备用铁素体和马氏体钢铸件A758/A758M-00 具有改良的切口韧性的对缝焊锻制碳素钢管配件A759-00 起重机用碳钢轨条A760/A760M-01 下水道和排水沟用金属涂覆的波纹钢管A761/A761M-98 现场栓接管、管拱和拱用波纹镀锌结构钢板A762/A762M-00 下水道和排水沟用预涂聚合物波纹钢管A763-93(1999)e1 铁素体不锈钢晶间腐蚀敏感性检测A764-95(2001) 机械弹簧用冷拉镀锌和按成品尺寸镀锌的碳素钢丝A765/A765M-98a 具有强制性韧性要求的碳素钢及低合金钢压力容器部件锻件A767/A767M-00b 钢筋混凝土用镀锌钢筋A768-95 涡轮机转子及轴用经真空处理的含铬12%的合金钢锻件A769/A769M-00 电阻焊钢结构型材A770/A770M-86(2001) 专用钢板通过厚度测量进行的抗拉试验A771/A771M-95(2001) 增殖反响堆堆芯部件用奥氏体不锈钢管A772/A772M-00 正弦电流用材料的交流磁导率的试验方法A773/A773M-96 用带直流电子的磁滞曲线记录仪的〔B－H〕回路法测量材料的磁性能的标准试验方法A774/A774M-00 低温和中温一般腐蚀情况下用的焊接锻制奥氏体不锈钢配件A775/A775M-01 涂环氧树脂的钢筋钢棒A778-01 焊接未退火的奥氏体不锈钢管形制品A779/A779M-00 预应力混凝土用应力消除未涂覆的密实七股钢丝绞绳A780-01 热浸镀锌层的损坏及无覆层区域的检修A781/A781M-00 一般工业用一般要求的钢和合金铸件A782/A782M-90(2001) 经淬火和回火的锰铬钼硅锆合金钢压力容器板A786/A786M-00b 轧制钢楼板A787-01 电阻焊金属涂覆碳素钢机械配管A788-98a 钢锻件A789/A789M-01 普通设备用无缝与焊接铁素体/奥氏体不锈钢管A790/A790M-01 无缝与焊接铁素体/奥氏体不锈钢管A792/A792M-99 热浸工艺法处理的55%铝-锌合金涂覆钢板A793-96 不锈钢轧制楼板A794-97 商品级冷轧碳素钢薄板(最高含碳量为0.16%-0.25%)A795-00 防火用黑色及热浸镀锌的焊接和无缝钢管A796/A796M-00 雨水管和卫生污水管及其它地下埋设管道用波纹钢管、管托架及拱形架结构设计惯例A798/A798M-01 下水道及其它类似用途用工厂制波纹钢管的安装A799/A799M-92(1997) 估算不锈钢铸件铁素体含量用仪表的校准A800/A800M-01 奥氏体合金钢铸件中铁素体含量的估算A801/A801M-99 铁钴高磁性饱和合金A802/A802M-95(2001) 钢铸件外观检验的外表验收标准A803/A803M-01 焊接铁素体不锈钢给水加热器管A804/A804M-99 在电力频率下用薄钢板型试样对材料交流磁特性的测试方法A805-93(1998) 冷轧碳素钢扁平线A807/A807M-97 下水道及其它类似用途用波纹结构钢涂覆管的安装A808/A808M-00a 具有改良的切口韧性的结构级高强度低合金碳钢、锰钢、铌钢和钒钢A809-98 镀铝碳素钢丝A810-00 镀锌钢管用绕网A811-97 粉末冶金技术制造的软磁铁零件A813/A813M-01 单或双焊接奥氏体不锈钢管A814/A814M-01 冷加工焊接奥氏体不锈钢管A815/A815M-01 锻制铁素体、铁素体/奥氏体和马氏体不锈钢管配件A817-00 链接栅栏网用金属涂覆钢丝A818-91(2001) 镀铜碳素钢丝A820-96 纤维增强混凝土用钢纤维A821/A821M-99 预应力混凝土容器用经回火的冷拉钢丝A822-90(2000) 液压系统设备用冷拉碳素无缝钢管A823-99 静铸永久铸模灰铸件A824-01 链接栅栏用Marcelled拉力金属涂覆钢丝A826/A826M-95(2001) 增殖反响堆堆芯部件用奥氏体和铁素体不锈钢管A827/A827M-93a(1998) 锻造及类似用途用的碳素钢板技术标准A829/A829M-00 结构性合金钢板A82-97ae1 钢筋混凝土用无节钢丝A830/A830M-00 按照化学成分要求提供的优质碳素钢板技术标准A831/A831M-95(2000) 核心部件用不锈耐热钢棒,坯段及锻件规格A832/A832M-99e1 压力容器板用铬钼钒及铬钼钒钛硼合金钢A833-84(1996) 用比较硬度测试仪测量金属材料的压痕硬性A834-95(2001) 一般工业用铁铸件的一般要求A835-84(2000) 铁合金与合金添加剂的筛分粒度A836/A836M-95b(2001) 搪瓷管和压力容器设备用钛稳定碳素体钢锻件A837-91(1996)e1 渗碳用合金钢锻件A838/A838M-97 继电器用易切削铁素体不锈软磁合金技术标准A839/A839M-96 软磁用途的磷铁粉末冶金制造的零件技术标准A840/A840M-00 全处理的磁性夹层钢A841/A841M-01 压力容器用温度机械控制工艺加工的钢板A842-85(1997) 高密度石墨铸铁A844/A844M-93(1999) 压力容器用直接淬火加工的含镍9%的合金钢板A845-85(2000) 用于脱氧与合金钢的钛碎片A846-85(2000) 用于脱氧与合金钢的铝碎片A847-99a 具有增强耐大气腐蚀性能的冷成型焊接与无缝高强度低合金结构管A848/A848M-96 低碳磁铁A849-00 波纹钢排水管和污水管用后涂覆铺面和衬里材料A851-96 高频感应焊接的未退火奥氏体钢冷凝器管A852/A852M-00a 最小屈服强度为70Ksi(485MPa),厚度为4英寸(100mm)的经淬火和回火的低合金结构钢板A853-93(1998) 普通碳素钢丝A854/A854M-98 镀锌高强度钢栅栏和格架用光滑金属线A855/A855M-98 锌-5%铝-铈合金涂覆的钢丝绳A856/A856M-98 锌-5%铝-铈合金涂覆的碳素钢丝A857/A857M-00a 冷成形轻型薄钢板桩A858/A858M-00 低温和腐蚀情况下用热处理碳素钢配件A859/A859M-95(1999) 压力容器部件用时效硬化镍铜铬钼钶低碳合金钢锻件A860/A860M-00 锻制高强度低合金钢的高强度对缝焊接配件A861-94e1 高硅铁管和配件A862/A862M-98 波纹钢污水管和排水管沥清(柏油)涂层的应用A865-97 钢管连接用黑色或镀锌焊接或无缝钢螺纹接头A866-94 耐磨中碳轴承钢A867/A867M-94(1998)e1 继电器用铁硅钢A871/A871M-00a 抗空气腐蚀的高强度低合金结构钢板。

astm a193 b7标准

astm a193 b7标准ASTM A193 B7是美国ASTM国际标准化组织制定的螺纹连接标准。

该标准适用于高温高压环境中的螺纹连接件，特别是用于在石油、化工、石化和能源行业中使用的设备和管道。

下面是ASTM A193 B7标准的相关参考内容。

1. 标准适用范围：ASTM A193 B7标准适用于直径为1/4英寸至4英寸的碳合金螺纹钢材连接件，如螺栓、螺母和螺柱。

2. 材料要求：ASTM A193 B7标准要求使用合适的冷作、淬火和回火工艺对钢材进行处理，以保证其力学性能和耐腐蚀性能。

同时钢材要符合化学成分和机械性能的严格要求。

3. 机械性能测试：ASTM A193 B7标准要求对钢材进行拉伸、冲击和硬度测试，以确定其强度、韧性和适应性。

拉伸测试要求钢材的最小屈服强度为105 ksi（720 MPa），最小抗拉强度为125 ksi（860 MPa）。

4. 耐腐蚀性能：ASTM A193 B7标准要求钢材具有优良的耐腐蚀性能，以确保其在恶劣环境中的使用寿命。

钢材要经过盐雾测试和硫化物应力腐蚀开裂测试，以验证其耐腐蚀性能。

5. 尺寸和重量：ASTM A193 B7标准规定了螺纹连接件的标准尺寸和重量范围，以确保其与其他设备和管道的兼容性。

螺纹连接件的尺寸根据直径、长度和内外螺纹类型进行分类。

6. 标记和包装：ASTM A193 B7标准要求螺纹连接件上必须标明材料级别和制造商的标识，以保证其可追溯性和质量认证。

螺纹连接件在包装时应采取合适的防腐措施，以防止腐蚀和损坏。

7. 制造商的责任：ASTM A193 B7标准强调制造商对产品质量的责任和义务。

制造商应按照标准的要求进行生产，并提供相关的质量文件和检测证明，以确保产品的质量符合标准要求。

8. 相关标准：ASTM A193 B7标准还提到了与其相关的其他标准，如ASTM A962/A962M（材料选用、机械性能测试和硫化物应力腐蚀开裂测试的标准规范）。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。