0191990008;中文规格书,Datasheet资料
19218;中文规格书,Datasheet资料
Jewel ® Workstation Continuous Mini Monitor DescriptionWorkstation Continuous Mini Monitor Figure 1. Desco 19218 Jewel ® Workstation Continuous Made in AmericaA broken wrist strap may expose products to ESD over an entire shift if it is checked only at shift changeESD MATPush and Clinch Snaps1-5/16"Figure 2. Installation of push and clinch snaps to worksurfaceNOTE: Install the monitor to the worksurface by aligning one snap at a time and applying a downward force directly above that snap.WorksurfaceMonitors worksurface connectionFigure 3. Installation of the monitor to the worksurface one snap at a timeThe following procedure will outline how to correctly wire Workstation Continuous Mini Monitor so as to properly monitor an ESD protected workstation.1. Confirm that the worksurface surface resistance is 5 x 10E8 Ohms or less and has a conductive layer.2. A convenient 120 VAC outlet should be located and tested for proper wiring and grounding. Werecommend the Desco 98130 AC Outlet Analyzer to verify proper wiring and ground.AC AdapterESD MATPark SnapFigure 4. Operating the Jewel® Workstation ContinuousHand Lotion. When leaving the area, a person can take the coil cord along or leave it attached to themonitor in park position.NOTE: Removing the banana plug from the monitor’s operator jack will disable the audio alarm.It is recommended that you use the Park Snap rather than continuously removing the Banana Plug from its jack. Doing so will increase the life span of the operator jack. If your process requires the constant insertion and removal of the banana plug, please contact your Desco Representative for alternate solutions.Specifications:Test range of monitored circuit:500K - 10M ohms†Worksurface Limit*:Set to 500 Megohms ± 20%Operating Voltage:24VAC, 50-60 HzWrist strap open circuit voltage:1.2 Volts peak to peak @ 1-2 MicroAmpsMat test open circuit voltage:5 - 7.5 VoltsResponse time to alarm:<50 mSOperating Temperature:32ºF - 100ºFHumidity Range:0-95% RH, non- c ondensingDimensions:2.77" L x 2.07" W x .71" H† This cannot be verified with standard DC test equipment. The continuous monitor is an impedance sensing device and the limits are determined by the magnitude and angle of the impedance.*Contact factory for special limits.NOTE: Worksurface must have a conductive layer such as Dual Layer Rubber or Dissipative 3-Layer Vinyl or Micastat® Dissipative Laminate with conductive buried layers. Desco continuous monitors are not recommended for use with homogeneous matting.Maintenance and CalibrationThe Jewel® Workstation Continuous Mini Monitor is solid state and designed to be maintenance free. It is calibrated to NIST traceable standards. There are no user adjustments necessary. Because of the wave distortion impedance sensing nature of the test circuit, special equipment is required for calibration. We recommend that calibration be performed annually using the Desco 98220 Continuous Monitor Calibration Unit. The Calibration Unit is a most important product which allows the customer to perform NIST traceable calibration on continuous monitors. The 98220 is designed to be used on the shop floor at the workstation, virtually eliminating downtime, verifying that the continuous monitor is operating within tolerances. The 98220 provides a simple and quick means to assure compliance verificaton Per ANSI/ESD S20.20 Table 3 per ESD TR53.Limited WarrantyDesco expressly warrants that for a period of one (1) year from the dateof purchase Desco Continuous Monitors will be free of defects in material(parts) and workmanship (labor). Within the warranty period, a creditfor purchase of replacement Desco Continuous Monitors, or, at Desco’soption, the Continuous Monitor will be repaired or replaced free of charge.If product credit is issued, the amount will be calculated by multiplying the unused portion of the expected one year life times the original unit purchase price. Call Customer Service at 909-627-8178 (Chino, CA) or 781-821-8370 (Canton, MA) for Return Material Authorization (RMA) and proper shipping instructions and address. Include a copy of your original packing slip,invoice, or other proof of date of purchase. Any unit under warranty should be shipped prepaid to the Desco factory. Warranty replacements will takeapproximately two weeks.If your unit is out of warranty, Desco will quote repair charges necessaryto bring your unit up to factory standards. Call Customer Service at 909-627-8178 (Chino, CA) or 781-821-8370 (Canton, MA) for a Return Material Authorization (RMA) and proper shipping instructions and address.Warranty ExclusionsTHE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU OFALL OTHER PRODUCT WARRANTIES, EXPRESSED AND IMPLIED,INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULARPURPOSE WHICH ARE SPECIFICALLY DISCLAIMED. The expresswarranty will not apply to defects or damage due to accidents, neglect,misuse, alterations, operator error, or failure to properly maintain, clean or repair products.Limit of LiabilityIn no event will Desco or any seller be responsible or liable for anyinjury, loss or damage, direct or consequent, arising out of the use of orthe inability to use the product. Before using, users shall determine thesuitability of the product for their intended use, and users assume all riskand liability whatsoever in connection therewith.分销商库存信息: DESCO19218。
0190060009;中文规格书,Datasheet资料
This document was generated on 08/24/2012PLEASE CHECK FOR LATEST PART INFORMATIONPart Number:19006-0009Status:ActiveDescription:Flag Avikrimp™ Quick Disconnect, Female, for 18-22 (0.80-0.35mm²) Wire, Mylar Tape, Tab 4.75 x 0.81mmDocuments:Drawing (PDF)Product Specification PS-19902-015 (PDF)Product Specification PS-19902-011 (PDF)RoHS Certificate of Compliance (PDF)Product Specification PS-19902-014 (PDF)Agency CertificationCSA LR18689ULE79133GeneralProduct Family Quick Disconnects Series19006Crimp Quality Equipment YesProduct Name Avikrimp™Type Quick Disconnect UPC800753031029PhysicalBarrel Type Closed Color - Resin Natural Flammability 94V-2GenderFemale Glow-Wire Compliant NoInsulationNylon (PA)Lock to Mating Part None Material - Metal Brass Material - Resin Nylon Net Weight 1.257/g OrientationFlagPackaging TypeAdhesive Tape on Reel Polarized to Mating Part NoTab Thickness 0.81mm Tab Width4.75mmTemperature Range - Operating -65°C to +105°C Wire Insulation Diameter 3.81mm max.Wire Size AWG 18, 20, 22Wire Size mm²0.35 - 0.80ElectricalVoltage - Maximum300V Material InfoOld Part NumberAA-5223TReference - Drawing NumbersProduct Specification PS-19902-011, PS-19902-014, PS-19902-015Sales DrawingCDFLA187Seriesimage - Reference onlyEU RoHSChina RoHSELV and RoHS Compliant REACH SVHCContains SVHC: No Low-Halogen Status Not ReviewedNeed more information on product environmental compliance?Email productcompliance@For a multiple part number RoHS Certificate of Compliance, click herePlease visit the Contact Us section for any non-product compliance questions.Search Parts in this Series 19006SeriesApplication Tooling | FAQTooling specifications and manuals are found by selecting the products below.Crimp Height Specifications are then contained in the Application Tooling Specification document.GlobalDescription Product #Crimp Dies for the ATP-301 Air Crimping Press for Mylar Tape Mounted Terminals0192880057Applicator Perishable Tool Kit0198032120This document was generated on 08/24/2012PLEASE CHECK FOR LATEST PART INFORMATION/分销商库存信息: MOLEX 0190060009。
0190990008;中文规格书,Datasheet资料
This document was generated on 08/10/2012PLEASE CHECK FOR LATEST PART INFORMATIONPart Number:19099-0008Status:ActiveOverview:Ring Tongue - Spade TerminalsDescription:InsulKrimp™ Snap Spade for 18-22 AWG Wire, Stud Size 5 (M3), Mylar Tape CarrierDocuments:Drawing (PDF)Product Specification PS-19902-011 (PDF)Product Specification PS-19902-009 (PDF)RoHS Certificate of Compliance (PDF)Agency CertificationCSA LR18689ULE32244GeneralProduct Family Ring and Spade Terminals Series19099Crimp Quality Equipment Yes Mil-Spec N/AOverviewRing Tongue - Spade Terminals Product Name InsulKrimp™Type Spade Snap UPC800753088771PhysicalBarrel Type Closed Color - Resin Natural Flammability 94V-0InsulationPVC Material - Plating Mating Tin Net Weight0.578/gPackaging Type Adhesive Tape on Reel Stud Size5 (M3)Wire Insulation Diameter 4.40mm max.Wire Size AWG 18, 20, 22Wire Size mm²0.25 - 1.50Material InfoOld Part NumberAA-2704-05XTReference - Drawing NumbersProduct Specification PS-19902-009, PS-19902-011Sales DrawingAACD20502Seriesimage - Reference onlyEU RoHSChina RoHSELV and RoHS Compliant REACH SVHC Not ReviewedLow-Halogen Status Not ReviewedNeed more information on product environmental compliance?Email productcompliance@For a multiple part number RoHS Certificate of Compliance, click herePlease visit the Contact Us section for any non-product compliance questions.Search Parts in this Series 19099SeriesApplication Tooling | FAQTooling specifications and manuals are found by selecting the products below.Crimp Height Specifications are then contained in the Application Tooling Specification document.GlobalDescription Product #Crimp Dies for MTA-100 Tape Applicator used in 3BF Press, MTA-105Tape Applicator used in TM-2000™ Press,and ATP-301 Air Crimping Press for Mylar Tape Mounted Terminals 0192880023Mini-Mac™Applicator0638851300This document was generated on 08/10/2012PLEASE CHECK FOR LATEST PART INFORMATION分销商库存信息: MOLEX 0190990008。
0191640989;中文规格书,Datasheet资料
Series
Physical
Barrel Type Gender Glow-Wire Compliant Insulation Lock to Mating Part Net Weight Orientation Packaging Type Polarized to Mating Part Tab Thickness Tab Width Temperature Range - Operating Wire Insulation Diameter Wire Size AWG Wire Size mm² Closed - Brazed Female No NiAc™ No 1.310/g Straight Adhesive Tape on Reel Yes 0.81mm 6.35mm 125°C 6.58mm max. 14, 16 1.30 - 2.00
This document was Nhomakorabeagenerated on 08/13/2012
PLEASE CHECK FOR LATEST PART INFORMATION
分销商库存信息:
MOLEX 0191640989
General
Product Family Series Crimp Quality Equipment Product Name Type UPC Quick Disconnects 19164 Yes Perma-Seal™ Quick Disconnect 822350973908 image - Reference only EU RoHS ELV and RoHS Compliant REACH SVHC Contains SVHC: No Low-Halogen Status Not Low-Halogen China RoHS
0190110036;中文规格书,Datasheet资料
This document was generated on 08/13/2012PLEASE CHECK FOR LATEST PART INFORMATIONPart Number:19011-0036Status:ActiveDescription:InsulKrimp™ Piggyback Quick Disconnect, Tab 6.35 x 0.81mm, 18-22 AWG, Red Insulator, ReelDocuments:Drawing (PDF)Product Specification PS-19902-011 (PDF)Product Specification PS-19902-008 (PDF)RoHS Certificate of Compliance (PDF)Agency CertificationCSA LR18689ULE79133GeneralProduct Family Quick Disconnects Series19011Crimp Quality Equipment YesProduct Name InsulKrimp™Type Quick Disconnect UPC822350948753PhysicalBarrel Type Closed Color - Resin Natural Flammability 94V-0GenderFemale Glow-Wire Compliant No InsulationPVC Lock to Mating Part No Material - Resin PVC Net Weight 1.026/g OrientationStraight Packaging TypeReel Polarized to Mating Part Yes Tab Thickness 0.81mm Tab Width6.35mm Temperature Range - Operating 105°CWire Insulation Diameter 2.79mm max.Wire Size AWG 18, 20, 22Wire Size mm²0.35 - 0.80ElectricalVoltage - Maximum600V AC Material InfoOld Part NumberAA-2301TReference - Drawing NumbersProduct Specification PS-19902-008, PS-19902-011Sales DrawingSD-19011-004Seriesimage - Reference onlyEU RoHSChina RoHSELV and RoHS Compliant REACH SVHC Not ReviewedLow-Halogen Status Not ReviewedNeed more information on product environmental compliance?Email productcompliance@For a multiple part number RoHS Certificate of Compliance, click herePlease visit the Contact Us section for any non-product compliance questions.Search Parts in this Series 19011SeriesApplication Tooling | FAQTooling specifications and manuals are found by selecting the products below.Crimp Height Specifications are then contained in the Application Tooling Specification document.GlobalDescription Product #Crimp Dies for MTA-105 Tape Applicator used in TM-2000™ Press,and ATP-301 Air Crimping Press for Mylar Tape Mounted Terminals0198002120This document was generated on 08/13/2012PLEASE CHECK FOR LATEST PART INFORMATION/分销商库存信息: MOLEX 0190110036。
0190390010;中文规格书,Datasheet资料
This document was generated on 08/13/2012PLEASE CHECK FOR LATEST PART INFORMATIONPart Number:19039-0010Status:ActiveDescription:Avikrimp™ Snap Plug Receptacle for 14-16 AWG Wire, Nylon, Fits Male Plug Diameter 4.57mmDocuments:Drawing (PDF)Product Specification PS-19902-013 (PDF)Product Specification PS-19902-011 (PDF)RoHS Certificate of Compliance (PDF)Agency CertificationCSA LR18689ULE152602GeneralProduct Family Quick Disconnects Series19039CommentsFits Male Plug Dia. 4.57mm Crimp Quality Equipment YesProduct Name Avikrimp™Type Snap Receptacle UPC800753049444PhysicalBarrel Type Closed Color - Resin Natural Flammability 94V-2GenderFemale Glow-Wire Compliant NoInsulationNylon (PA)Lock to Mating Part None Material - MetalBrass Material - Plating MatingTin Material - Plating Termination Tin Material - Resin Nylon Net Weight 1.361/g OrientationStraight Packaging Type Bag Tab Thickness N/A Tab WidthN/ATemperature Range - Operating -40°C to +105°CTermination Interface: Style Crimp or Compression Wire Insulation Diameter 3.81mm max.Wire Size AWG 14, 16Wire Size mm²1.00 -2.50ElectricalVoltage - MaximumPer Wire Specification Material InfoOld Part NumberBRB-8180NReference - Drawing NumbersProduct Specification PS-19902-011, PS-19902-013Sales DrawingSD-19039-001Seriesimage - Reference onlyEU RoHSChina RoHSELV and RoHS Compliant REACH SVHC Not ReviewedLow-Halogen Status Not ReviewedNeed more information on product environmental compliance?Email productcompliance@For a multiple part number RoHS Certificate of Compliance, click herePlease visit the Contact Us section for any non-product compliance questions.Search Parts in this Series 19039SeriesApplication Tooling | FAQTooling specifications and manuals are found by selecting the products below.Crimp Height Specifications are then contained in the Application Tooling Specification document.GlobalDescription Product #Hand Crimp Tool 0640012100Crimp Head for the AT-200™ Pneumatic Hand Tool0640052100This document was generated on 08/13/2012PLEASE CHECK FOR LATEST PART INFORMATION分销商库存信息: MOLEX 0190390010。
0191930007;中文规格书,Datasheet资料
This document was generated on 08/09/2012PLEASE CHECK FOR LATEST PART INFORMATIONPart Number:19193-0007Status:ActiveOverview:Ring Tongue - Spade TerminalsDescription:VersaKrimp™ Ring Tongue Terminal for 18-22 AWG WireDocuments:Drawing (PDF)Product Specification PS-19902-013 (PDF)Product Specification PS-19902-011 (PDF)RoHS Certificate of Compliance (PDF)Agency CertificationCSA LR18689ULE32244GeneralProduct Family Ring and Spade Terminals Series19193Crimp Quality Equipment Yes Mil-Spec N/AOverviewRing Tongue - Spade Terminals Product Name VersaKrimp™Type RingUPC800753038295PhysicalBarrel Type Closed - Brazed InsulationNone Material - Plating Mating Tin Net Weight0.370/g Packaging Type BagStud Size3-4 (M2.6)Wire Size AWG 18, 20, 22Wire Size mm²0.35 - 0.80Material InfoOld Part NumberAA-320-04Reference - Drawing NumbersProduct Specification PS-19902-011, PS-19902-013Sales DrawingAACD30101Seriesimage - Reference onlyEU RoHSChina RoHSELV and RoHS Compliant REACH SVHCContains SVHC: No Low-Halogen Status Not ReviewedNeed more information on product environmental compliance?Email productcompliance@For a multiple part number RoHS Certificate of Compliance, click herePlease visit the Contact Us section for any non-product compliance questions.Search Parts in this Series 19193SeriesApplication Tooling | FAQTooling specifications and manuals are found by selecting the products below.Crimp Height Specifications are then contained in the Application Tooling Specification document.GlobalDescription Product #Hand Crimp Tool 0640030100Crimp Head for the AT-200™ Pneumatic Hand Tool0640070100This document was generated on 08/09/2012PLEASE CHECK FOR LATEST PART INFORMATION/分销商库存信息: MOLEX 0191930007。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
This document was generated on 08/31/2012
PLEASE CHECK FOR LATEST PART INFORMATION
Part Number:19199-0008Status:Active
Description:
Avikrimp™ Window Butt Connector for 18-22 AWG Wire, Mylar Tape Carrier
Documents:Drawing (PDF)
Product Specification PS-19902-015 (PDF)Product Specification PS-19902-011 (PDF)
RoHS Certificate of Compliance (PDF)
General
Product Family Splices Series
19199
Comments
Mil Spec M7928/5-3Crimp Quality Equipment Yes
Mil-Spec
M7928/5-3
Product Name Avikrimp™, Butt - Window UPC
800753046818Physical
Barrel Type Closed Insulation
Nylon (PA)Material - Metal Copper Net Weight
1.194/g
Packaging Type
Adhesive Tape on Reel Temperature Range - Operating -55°C to +105°C Wire Insulation Diameter 3.56mm max.Wire Size AWG 18, 20, 22Wire Size mm²
0.25 - 1.50Electrical
Voltage - Maximum
300V Material Info
Old Part Number
WA-840T
Reference - Drawing Numbers
Product Specification PS-19902-011, PS-19902-015Sales Drawing
SD-19199-003
Series
image - Reference only
EU RoHS
China RoHS
ELV and RoHS Compliant REACH SVHC
Contains SVHC: No Low-Halogen Status Low-Halogen
Need more information on product environmental compliance?
Email productcompliance@
For a multiple part number RoHS Certificate of Compliance, click here
Please visit the Contact Us section for any non-product compliance questions.
Search Parts in this Series 19199Series
Application Tooling | FAQ
Tooling specifications and manuals are found by selecting the products below.Crimp Height Specifications are then contained in the Application Tooling Specification document.Global
Description Product #Crimp Dies for MTA-100 Tape Applicator used in 3BF Press, MTA-105Tape Applicator used in TM-2000™ Press,and ATP-301 Air Crimping Press for Mylar Tape Mounted Terminals
0192880043This document was generated on 08/31/2012
PLEASE CHECK FOR LATEST PART INFORMATION
分销商库存信息: MOLEX 0191990008。