KD-450+BM-500L型 全自动高速边封热收缩包装机
热收缩包装机操作规程
热收缩包装机操作规程《热收缩包装机操作规程》一、操作前准备1. 确保热收缩包装机的工作环境整洁，无杂物。
2. 检查电源是否正常，电压和频率是否符合要求。
3. 检查机器是否有损坏或存在安全隐患。
4. 确保热收缩包装机的工作面积足够，周围没有障碍物。
二、设备操作1. 启动热收缩包装机前，必须戴好安全帽、手套，并穿戴好工作服。
2. 打开主电源，检查机器所有的控制按钮是否在零位。
3. 开启热收缩包装机的加热系统，在加热系统预热到设定温度之后，才能进行下一步操作。
4. 选择合适的包装膜和调节好热收缩包装机的包装尺寸。
5. 放置产品在包装膜上，并将其包裹。
6. 将包装后的产品送入热收缩包装机中，开启热收缩系统，将产品进行封装和收缩。
三、操作注意事项1. 在操作过程中，需要保持注意力集中，避免发生意外。
2. 不得在机器运行时将手或其他物体伸入热收缩包装机内部。
3. 热收缩包装机运行时，不得进行其他任何维修保养工作。
4. 操作结束后，必须关闭所有的电源开关，并将热收缩包装机清洁干净。
四、故障排除1. 当热收缩包装机出现异常情况，必须立即停机并关闭所有电源，然后联系专业人员进行检查维修。
2. 不得私自进行热收缩包装机的维修和维护工作，以免造成更大的损害。
五、安全注意事项1. 在操作热收缩包装机时，必须严格按照操作规程进行操作，避免违规操作。
2. 操作人员必须具备一定的操作经验和技能，不得擅自操作热收缩包装机。
3. 热收缩包装机的日常维护保养工作必须及时进行，确保机器的正常运行。
4. 在操作过程中，必须随时保持机器周围的整洁，避免杂物的干扰。
5. 处理热收缩包装机的废料时，必须按照相关规定进行处理，避免造成环境污染。
在使用热收缩包装机时，严格按照《热收缩包装机操作规程》进行操作，不仅可以确保机器的安全运行，还能够提高工作效率，保护环境。
同时，不断加强对操作规程的学习和掌握，提高操作人员的技能水平，是非常重要的。
今超越立式全自动包装机参数设置
今超越立式全自动包装机参数设置全自动包装机是工厂自动化技术的最新应用，替代了预制袋成形方式,大大提高了工
作效率、为各企业广泛采用。
全自动包装机参数：
型号：JD2403
包装膜宽：100-400mm
制成袋尺寸：40-200mm
包装速度：1-40袋/分钟
控制系统：PLC+光电+气源+中/英文操作屏幕
气源：0.4m3/分钟
功率：2400瓦
电源：交流电220V
重量：约重260kg
尺寸：1300*800*1650mm长*宽*高
全自动包装机
全自动包装机的主要特点
1、进口PLC全电脑控制系统，光栅计数、人机界面，操作简便、直观；
2、伺服动膜系统，气动控制系统，定位准确；同步动膜，稳定性高。
3、采用智能温控器，温度控控制准确；保证封口美观平整。
4、设有多种停机报警功能，减低损耗。
5、本机采用全自动完成计量、计数、制袋、填充、封合、日期打印等操作。
该机为组合式，分为震动盘、光栅计数、下料部分和制袋包装部分；该机标准配置为三个震动盘；可选择增加多个，以提高包装产品的多样化。
远红外收缩膜包装机操作规程
10、操作过程中，应互相配合，避免产品的损坏。
三、故障排除及维修
四、故障的排除和维修必须由专人负责，具体情况见操作说明书。
备注：其它注意事项说明：
远红外收缩膜包装机操作规程
一、检查准备
1、查看各电器开关、仪表的情况是否处插上总电源插头。
二、操作程序
1、合上侧热开关(2)
2、合上上热开关(3)，调节上热按钮(4)至4档左右。
3、合上下热开关(6)，调节下热按钮(7)至4档左右。
4、合上输送开关(11)，调节输送按钮(9)至4~5档。
5、以上操作完成后，让机器运转3分钟左右再合上热风开关(12)(实际操作中也可不开热风开关)。
6、放上已装好收缩膜的产品，即可进行收缩包装。
7、在实际情况中，如果收缩后皱纹过多，可减低输送速度或提高各加热部位温度。反之，如果出现过热现象，则可降低温度。
8、包装工作结束后，先关闭三组加热开关，让输送电机和热风电机继续运行10分钟左右，再关闭输送风扇电源开关，切断总电源。
L型全自动热收缩包装机封刀介绍
L型全自动热收缩包装机封刀的介绍在热收缩机的分类里最明显的一类就是L型全自动热收缩包装机，他是目前热收缩机中最先进、自动程度较高的一款产品。
这款L型全自动热收缩包装机多配流水线使用，可以自动送膜、然后自动制袋、表面抚平，封口切膜打包、热收缩包装一次完成，无须人工。
为了区别热收缩机的其他设备，我们通常也把L型全自动热收缩包装机称作全自动L型封切收缩机，它使用对折膜为原材料，且废料可回收。
另外，针对包装大小不一的情况，此L型全自动热收缩包装机可以在一定范围内调整，不用更换磨具。
同时可以手动调整的部位还有热收缩炉温度和热收缩包装的速度。
产品广泛用在制药、食品、文具、化妆品、电子产品、玩具等领域。
L型全自动热收缩包装机封刀的区别，很多客户都不明白为什么全自动的设备和半自动的设备价格差别怎么会如此之大。
这里有的很多细节是有所差别的，最主要的一点就是封刀的差别。
我们普通的半自动封切刀是镍铬合金材质的，它的特点是铬合金具有高强度和抗腐蚀性，与铁和镍组成的合金俗称不锈钢。
常用于切削工具；用喷镀、沉积和高温扩散等方法在钢或铁的表面形成抗腐蚀合金层；重铬酸钾和重铬酸钠是有机合成和石油工业中的强氧化剂；铬黄、铬橙、铬绿等可用作无机颜料。
技术利用这一原理把原材料加工成一个几毫米宽的薄片卡在刀槽里来对它进行加热封切。
而我们的L型全自动热收缩包装机上使用的封切刀则是采用更先近的高塑钢为原材料来制作的。
高塑钢：一种具有高硬度、高耐磨性和高耐热性的工具钢。
再给切刀外层镀特氟龙。
这种材料的产品一般统称作"不粘涂层"，是一种使用了氟取代聚乙烯中所有氢原子的人工合成高分子材料。
这种材料具有抗酸抗碱、抗各种有机溶剂的特点，几乎不溶于所有的溶剂。
同时，聚四氟乙烯具有耐高温的特点，它的摩擦系数极低，所以可作润滑作用之途，亦成为了不沾锅和水管内层的理想涂料。
当切刀频繁切割PE膜，薄膜受热会融化就会有残留在切刀上，如果是其他材质的切刀有了残留后就不能再很平整的切割薄膜，那么接口有会有褶皱或缺口，热收缩时会出现破裂现象。
自动封切热收缩膜包装机使用指南
英文回答：—Other OrganiserThe ATM is an efficient packaging device that is widely used in the food， medicine， chemical， etc。
The proper use and maintenance of the encapsulation accelerator is important to improve the efficiency of the packaging and to safeguard the quality of the product。
In order to help users to better use and maintain the equipment， this guide is being developed to describe the basic operating steps of the auto—capture thermal retort packaging machine and themon trouble management method。
Users are expected to be able to read carefully andply with them， and to ensure that the production line works properly and is stable。
Your Honor。
尊敬的用户：自动封切热收缩膜包装机是一种高效的包装设备，在食品、医药、化工等行业得到广泛应用。
正确使用和维护封切热收缩膜包装机对提高包装效率、保障产品质量具有重要意义。
为了帮助用户更好地使用和维护该设备，特编撰此指南，介绍自动封切热收缩膜包装机的基本操作步骤以及常见故障处理方法。
望用户能够认真阅读并遵照实施，保障生产线的正常运行与稳定生产。
包mylar机的原理
包mylar机的原理
包mylar机是一种常见的食品包装机械，它通过一系列的工艺流程将食品包装成具有保鲜、防潮、防氧化等功能的包装袋。
其原理主要涉及包装材料、封口技术和控制系统三个方面。
包mylar机的原理涉及到包装材料的选择和使用。
常见的包装材料有塑料薄膜、金属箔和纸张等。
塑料薄膜一般采用聚乙烯、聚丙烯、聚氯乙烯等材料，具有良好的柔韧性和耐用性。
金属箔常用的有铝箔，能够有效地隔绝氧气和湿气，具有良好的保鲜效果。
纸张则常用于包装一些干燥的食品，如面包、饼干等。
包mylar机的原理还涉及到封口技术。
常见的封口技术有热封和冷封两种。
热封是通过加热封口部位，使塑料薄膜熔化并粘结在一起，形成密封效果。
冷封则是通过在封口部位加入一定的压力，使塑料薄膜在接触面上形成一定的粘结力，实现封口。
这两种封口技术各有优缺点，根据不同的包装需求选择合适的封口方式。
包mylar机的原理还涉及到控制系统。
控制系统主要包括传感器、PLC控制器和触摸屏等。
传感器用于检测包装材料的位置和状态，将信号传递给PLC控制器。
PLC控制器根据传感器的信号和预设的程序，控制机械的运行、温度的调节和封口的时间等。
触摸屏则用于操作人员与包mylar机进行交互，设置包装参数和监控包装过程。
包mylar机的原理涉及到包装材料、封口技术和控制系统三个方面。
通过合理选择包装材料，采用适当的封口技术，并利用先进的控制系统，包mylar机能够实现食品的有效包装，提高食品的保鲜性和防潮性，延长食品的货架期，满足人们对食品品质和安全性的需求。
全自动热收缩膜包装机操作规程
全自动热收缩膜包装机操作规程一、操作前准备1. 检查设备和周围环境是否整洁，无明显杂物和障碍物；2. 确认设备电源已连接并处于正常工作状态；3. 检查包装机的所有控制开关是否处于关闭状态；4. 准备好待包装的产品和热收缩膜。
二、设备启动1. 打开包装机的电源开关，并等待设备自检完成；2. 检查加热系统的工作状态，确认加热管是否正常工作；3. 调节输送带的速度和张力，以适应待包装产品的尺寸和重量。
三、设置包装参数1. 根据待包装产品的尺寸和形状，调整热收缩膜的宽度和长度；2. 根据产品的特性和热收缩膜的材质，设置适当的包装温度和时间；3. 调整热收缩膜的收缩力度，以确保包装效果的美观和牢固。
四、开始包装1. 将待包装产品放置在输送带上，并确保产品的位置和方向正确；2. 启动输送带和包装机，观察包装效果并调整参数，直至达到理想的包装效果；3. 检查包装后的产品，确认包装效果符合要求。
五、包装结束1. 关闭包装机的电源开关，等待设备停止运转并自动冷却；2. 清理包装机和周围环境，确保设备和工作区域整洁；3. 关闭电源开关，断开电源连接，完成包装机的关闭和停机操作。
六、设备维护1. 定期清理包装机的输送带、加热管和热收缩膜传动部件，以确保设备的正常运转；2. 检查包装机的各项传动部件和控制系统，及时发现并处理设备故障；3. 保持包装机的润滑和维护，延长设备的使用寿命和性能稳定性。
七、安全注意事项1. 在操作过程中，避免手部和衣物接近加热管和输送带，以防烫伤或卡紧；2. 使用设备时，注意防止异物进入包装机内部或热收缩膜传动部件，防止设备故障或事故；3. 维护和保养设备时，需先切断电源并等待设备完全停止运转，以确保操作安全。
八、总结全自动热收缩膜包装机是一种高效、稳定的包装设备，合理的操作规程可以最大限度地发挥设备的性能和效果。
操作人员在使用包装机时，应严格按照操作规程执行，确保设备的正常工作和操作的安全性。
热收缩膜包装机操作规程
热收缩膜包装机操作规程一、前言热收缩膜包装机是一种广泛应用于产品包装行业的设备，能够将包装物紧密地包裹起来，起到保护和美观的作用。
为了确保操作的安全和高效，我们制定了以下热收缩膜包装机操作规程，希望能够帮助操作人员正确使用该设备。
二、操作前准备1. 检查设备的电源是否正常，并确保设备接地良好。
2. 检查设备的各个部件是否完好无损，如热刀、输送带、传感器等。
3. 清洁机器表面，确保无尘、无杂物。
三、操作流程1. 打开设备总电源，并打开控制面板电源开关。
2. 通过控制面板设置合适的包装参数，如包装速度、温度等。
根据包装物的特性和要求进行调整。
3. 将待包装的物品放置在输送带上，并调整输送带的位置和速度，使其能够顺利通过热收缩膜。
4. 打开热收缩膜供给装置，并调整好膜的宽度和张力，确保膜能够平稳地包裹在产品上。
5. 确保机器正常运行后，按下启动按钮，设备开始工作。
6. 观察包装过程中的各个环节，确保热收缩膜能够完整地包裹在产品上，并确保热刀能够准确地切割膜。
四、操作注意事项1. 在操作过程中，操作人员应保持专注，不得随意离开设备。
2. 切勿将手或其他物体伸入设备内部，以防发生意外。
3. 避免在设备运行时触摸热刀或热收缩膜，以免烫伤。
4. 当设备发生异常情况时，如热刀异常、膜断裂等，应立即停止设备并进行维修。
5. 定期对设备进行清洁和保养，保持设备的正常运行状态。
6. 在清洁和维护设备时，应先切断电源，并等待设备冷却后再进行操作。
7. 在更换热收缩膜时，应使用适当的工具，并确保操作安全。
五、操作后收尾工作1. 停止设备运行，关闭电源开关。
2. 清理设备表面的杂物和残留物，确保设备整洁。
3. 关闭热收缩膜供给装置，并清理膜残余。
4. 对设备进行日常维护和保养，如润滑传动部件等。
5. 对设备进行定期检查和维修，确保设备性能稳定。
六、安全警示1. 严禁将手或其他物体伸入设备内部，以免发生意外。
2. 在设备运行时，应保持专注，避免分心。
收缩包装 热收缩包装机械使用说明书
热收缩包装机主要针对饰品厂，制品厂，工艺厂，毛刷制品厂，化妆品厂，乳制品厂家等等需要贴体包装效果的用户都需要使用红外线收缩包装机，这款BS-B 收缩包装机主要和脚踏封口机配套使用，所以需要贴体包装的产品需要先经过封口机将袋子封口完毕后，放入收缩包装机内部经过高温烤后多余的PE袋可以贴产品恨紧凑看起来美观，发货时安全不容易损坏凯比奇包装推荐需要贴体包装的用户可以到我公司现场参观测试效果满意后在考虑是否购买。
BS-F400热熔收缩包装机参数:产品型号:BS-F400电源电压:220V 50Hz功率: 5.5KW输送速度:0-10m/min输送重量:10kg工作室尺寸:800×400×200mm外形尺寸:1100×570×670mm重量:40kg购买提示：需要这款热收缩包装机的用户需要知道自己的产品大小，我们这款红外线收缩包装机可使用加热收缩室尺寸为：800×400×200mm大于这个尺寸需要选择其它规格收缩包装机。
BS-F400收缩包装机市面叫法：热收缩包装机，收缩打包机，热收缩包装机械，PE热收拾打包机，PE袋收缩包装机，红外线收缩包装机，红外线热收缩包装机，高科技红外线收缩打包机，快速收缩包装机，加热收缩包装机，加温收缩包装机，快速加热红外线收缩机，生产收缩包装机，热收缩膜包装机，热收缩膜包装机价格，自动热收缩膜包装机，热收缩包装机价格，远红外热收缩包装机，餐具收缩包装机，刀叉热收缩包装机，小饰品收缩包装机，化妆品热收缩包装机，瓶子热收缩包装机，餐具打包机,贴体包装机，贴体收缩包装机，贴体PE袋包装机，贴体塑料袋打包机BS-F400红外线收缩包装机主要功能：1、经过收缩产品后到达密封。
2、经过收缩包装后的产品更防潮。
3、经过红外线收缩包装过的产品防污染。
4、经过红外线收缩后产品具有一定的缓冲性。
5、经过红外线收缩后的产品可降低产品被拆的可能性。
热收缩包装机使用说明书
热收缩包装机使用说明书文稿归稿存档编号：[KKUY-KKIO69-OTM243-OLUI129-G00I-FDQS58-热收缩包装机使用说明书一、简介目前本厂生产的包装机械设备是参照近期国内同行产品，改进后，重新组合的新一代包装设备。
与同类型相比，其造型大方，结构紧密，性能可靠。
对高要求的产品包装，食物包装所指定的无毒性，忽度性，耐高温也不破裂的PE、PP、PVC收缩膜包装特别适合。
运用于食品、化妆品、化工品、工业用品、饮料、陶瓷等包装。
包装后的产品具有透明、美观、高雅，还可以达到防潮、防尘、防锈等效果。
本机选用高精度电子温度控制器控温。
在常温至300℃可任意调节。
并可根据材料的差异准确地控制收缩温度，优先选用高质量红外线石英管作发热系统。
采用进口大功率管作无极调速，自动稳压，确保输送速度平稳。
一次性快速完成，薄膜加热、贴体、抽气、密封等包装程序及成品合格率高等优点，深受广大用户欢迎。
二、远红外线收缩机规格及主要参数3.机器重量：120KG三、调试方法1.单相接线方式，把本机电源电缆接至电源处，接线方式：相线、中性线（即零线）、接地线及接地端子必须可靠接地。
2.试机：电源电缆接好后送上电源，在控制面板上，将温度控制器调到零位。
输送带、上、下发热线管旋钮调到零位（往左边调）再合上电源开关、风机开关，输送带适当的调节，让其运转。
然后调节温度控制器设定温度。
再调上、下发热管旋钮调到最大（往右边调）。
此时机器已经处于工作升温状态。
待温度上升到设定温度值时（温度表指示到设定温度值，表头指示红灯亮），即可进行产品包装试机。
3.工作温度设定：PVC膜一般为120℃-160℃，PP膜为150-180℃。
根据产品第一包装情况来调整温度高低及输送带速度。
产品出现皱纹时，表明温度不够或输送速度太快。
产品薄膜破裂时，表明温度过高或输送带速度太慢。
多次试机使产品达到最佳效果，此时请记下温度值及输送电压值，待下次开机时方便使用。
IMCL-500型立式自动包装机操作手册说明书
Operation Manual of IMCL-500 Type Vertical Automatic Packing MachineI. Technical parametersIMCL-500 Vertical-bag automatic liquid packaging machine adopts pneumatic drive, PLC control and touch screen man-machine interface, can automatically complete the whole packaging process, including bag making, capping, filling and measuring, sealing and cutting, date printing and finished product output. During the packaging process, the photoelectric calibration device will be used to ensure the integrity of the pattern of packaging bags.This machine has reasonable structure design, beautiful model, reliable working, accurate measurement, and easy to operation, adjustment and maintenance. It is applicable to the packaging of various non-carbonic beverages, fruit juice, wine (alcohol content is less than 60°), edible oil, vinegar, sauce and drinking water, and viscous materials, such as jams, spices and detergents having certain liquidity.The technical parameters of this machine are as follows:Production capacity: 15～30bags/minAir consumption: 0.4m3/min (0.8MPa)Packaging capacity: 150～1200ml (need to replace the fittings)Power supply voltage: AC220±10％V 50HzMeasuring accuracy: ±1.5％Whole machine power: maximum 4.0kw, normal work 2.0kwFilm width: 400～650(mm)Machine weight: 650kgWorking pressure: 0.65MPaAppearance size: 1950!1200!2500(mm)Film thickness: 0.10～0.14(mm)Structure introduction of vertical-bag automatic liquid packaging machine1. 传送带—Conveyer belt2. 横封切断机构—Horizontal sealing shutdown mechanism3. 膜牵引机构—Film traction mechanism4. 纵封机构—Vertical sealing mechanism5. 操作箱—Operating box6. 纵封高度调节机构—Vertical sealing height adjusting mechanism7. 袋折叠机构—Bag folding mechanism8. 电器箱—Electric appliance box9. 供料机构—Product feeding mechanism10. 供膜机构—Film supplying mechanism11. 打孔机—Hole-punching machine12. 下料管—Discharge pipeFigure 1 Structure diagram of packaging machineII. Performance introduction and adjustment methods of each part1. Composition of the whole machineThe machine consists of one main unit (packaging machine) and one belt conveyer (see the above Figure 1).2. Introduction and adjustment of the main mechanism ofpackaging machineNote: if the operations or adjustments mentioned below relate to the dangerous places, they only can be carried out after stopping the machine and pressing the emergency stop button.2.1 Conveyer beltThe conveyer belt of this machine is driven by the independent motor andreducer, and its startup and shutdown are controlled by the button of“conveyer belt” on the touch screen.1. Drive motor2. Drive roller3. Belt4. Driven roller5. Driven shaft6. Tension adjusting screw7. Operating slide8. Rear support9. Height adjusting nut10. Front supportFigure 2 Conveyer beltAs shown in Figure 2, rotate two tension adjusting screws 6 of the rear end, can adjust the tightness of the belt to balance the tension on both sides of belt; rotate the height adjusting nut 9, can change the height of the rear end of conveyer belt, and adjust to the appropriate height (under the normal working condition, the distance from belt to packaging bags is 20-30mm), then lock two nuts.2.2 Horizontal sealing shutdown mechanismThe mechanism consists of heat sealing, cold pressing part, shutdown part and servo lifting part. During the packaging process, it will complete the sealing, smashing, cutting-off and film tracking on both sides of packaging bags. The structure composition is shown in Figure 3.1. Servo motor2. Cold pressing cylinder3. Horizontal sealing cylinder4. Litter5. Horizontal sealing back6. Horizontal sealing head7. Pressure adjusting screw8. Shutdown cylinder9. Cold pressing head10. Blade11. Cold pressing back12. Pressure adjusting nut13. Lifting crank14. Lifting connecting rod15. Connecting rod nutFigure 3 Horizontal sealing shutdown mechanisms2.2.1 If the seal doesn’t fit due to the unbalance pressure of horizontal sealinghead, it can adjust the pressure of head ends and middle part through five pressure adjusting screws 7, make them balance, and then lock the nuts after the completion of adjustment. The five screws will not change the sealing head pressure, but can distribute the force of the cylinder on the whole sealing head uniformly.2.2.2 If the width of both seal sides of packaging bags is different significantly, itcan change the height of horizontal sealing back 5 and horizontal sealing head 6, until no significant difference of width on both seal sides.Horizontal sealing back 5 and horizontal sealing head 6 shall be aligned with each other during the adjustment process.2.2.3 Adjust the pressure adjusting nut 12, can make the balance of cold sealingpressure.2.2.4 Blade 10 is the part need to be replaced appropriately according to theservice condition, and the replacement method is shown below: put inner hexagonal wrench in the slot hole at the right lower end of cold sealing pressure head (facing machine), loosen the screws of two clamp blades, remove the blade, plug the new blade into the original position and then lock the screw. The angle between the cutter edge and the plane of sealing head shall be between 135° to 160°, and the knifepoint is revealed 2-3 mm above the plane.2.2.5 Usually check whether the nut on both ends of lifting connecting rod 14 isloose, and timely fasten.2.3 Vertical sealing mechanismVertical sealing mechanism consists of bag top opening sealing part and bag bottom sealing part, as shown in Figure 4.1. Vertical sealing cylinder2. Fastening handle3. Bag bottom sealing back4. Bag bottom sealing head5. Bag opening sealing back6. Bag opening sealing head7. Pressure adjusting screwFigure 4 Vertical sealing mechanism2.3.1 Loosen the fastening handle 2, can move the corresponding sealing back orsealing head to the right and left sides, and realize the changes for arc height of bag bottom or width of upper seal.2.3.2 Adjust four pressure adjusting screws 7 to balance the sealing head pressureof bag bottom.2.4 Vertical sealing height adjusting mechanism (Figure 5)1. Vertical sealing height adjusting hand wheel2. Fastening hand wheel3. Vertical sealing adjusting screw4. Vertical sealing link blockFigure 5 Vertical sealing height adjusting mechanismTwo vertical sealing height adjusting hand wheels 1 can adjust the height of vertical sealing mechanism to align with the sealing position of bag bottom. Loosen the fastening hand wheel 2, rotate the vertical sealing adjusting hand wheel 1, and then lock the fastening hand wheel 2 after completing the adjustment.2.5 Bag folding shaping mechanism (Figure 6)1. Set square2. Film guiding roller3. Bag bottom folding supportFigure 6 Bag folding shaping mechanismThe positions of set square 1 and four film guiding rollers 2 have been adjusted before leaving the factory, without adjustment in the work. Bag bottom folding support 3 plays a role of assisting bag shaping, and can change the folding depth of bag bottom to some extent; loosen the fastening screw, and can rotate up and down, to make it fold to the appropriate depth, but do not rise too tight, otherwise it is easy to scratch the packaging film.2.6 Product feeding mechanismThe machine adopts the quantitative product feeding device composed by pneumatic piston measuring cylinder and double one-way valve, with adjustable packaging capacity and high measuring accuracy. As shown in Figure 71. Feed pipe2. Discharge pipe3. One-way valve4. Product feeding cylinder barrel5. Piston6. Product feeding cylinder7. Measuring adjusting nut8. Locking nutFigure 7 Product feeding mechanism2.6.1 After each cleaning or dismantling, install two one-way valves 3 with theacting force of internal valve plate downward.2.6.2 When installing the product feeding cylinder barrel 4 and piston 5, you shallmake them be concentric as much as possible, and do not rub each other in movement, to avoid the damage.2.6.3 The adjustment of measuring size: rotate the measuring adjusting nut 7inward, and make L in Figure 8 become shorter, can reduce the measuringcapacity; on the contrary, it can increase the measuring capacity, after the adjustment is completed, install the locking nut 8 and interlock with the measuring adjusting nut 7, to avoid loosening and affecting the measurement.2.6.4 Where excessive measuring accuracy arise, check whether all pipeconnectors are locked, or examine whether one-way valve 3 and piston 5 are worn; if the seal ring of piston 5 is worn badly, it may cause the leakage of piston rear-end.2.7 Film supplying mechanism:use the complete suspension type structure, and consist of film supplying mechanism frame, hole-punching machine, code printer, film supplying motor, film roller, proximity switch (film supplying detection), optical fiber and amplifier (cursor detection), and film automatic rectification device, etc.(see Figure 8).1. Film loading shaft2. Film supplying motor3. Thermal ribbon code printer4. Cursor detection5. Hole-punching machine6. Rectification detection7. Automatic rectification mechanism8. Film storage swing leverFigure 8 Film supplying mechanism2.7.1 Film loading shaft 1 is used to carry the film roll, adjust two catch wheels to theright and left sides when loading the film roll for the first time, make the film roll in the middle position (can measure the distance between both film roll ends and film mounting side panels with the ruler, to make equal), match the screws on the left side catch wheel with the top slot on the film loading shaft 1 and tighten, and have no need of moving the left side catch wheel when you load the film roll every time; after the left side catch wheel is fixed, use force in tightening the right side catch wheel.2.7.2 Film supplying motor 2 is controlled by proximity switch, when the packagingfilm is towed (including automatic operation, point feeding and manually drawing packaging film), and the swing lever 8 rises to the position of top proximity switch, film supplying motor 2 starts to operate and supply the film, and the fixed time of motor rotation is set by the program; when the swing lever8 goes down to the proximity switch at the bottom, indicating that this roll ofpackaging film is used up, the packaging machine will automatically shut down, then you need to replace the new packaging film roll.2.7.3 Thermal ribbon code printer 3, cursor detection 4 and hole-punching machine aremoved all round.2.7.4 Cursor detection 4 is composed of optical fiber head, fiber amplifier andauxiliary parts, and the distance between the end face of optical fiber head and baffle board is 3mm ~ 5mm; when the optical fiber head is fixed on the mounting plate, the tightening force of fixing nut (m6) shall not be too large, and the maximum tightening torque is 10kgf-cm; when the end face of optical fiber head is contaminated, clean it with lens wiping paper, and avoid scratching the end face of optical fiber head. When adjusting the cursor detection 4 forwards and backwards, use hole-punching machine 5 to cooperate with the adjustment, and make the front and rear positions of the holes on the packaging film are located at the pattern cutting of two packaging bags, i.e., the cutting line of thefinished bags; while adjust the cursor detection 4 to the right and left sides, make the center of red light-spot is located in the middle of the length direction of cursor block to be detected.2.7.5 The centre distance between two punches of hole-punching machine 5 has beenadjusted according to the size of the user’s packaging bags before leaving the factory; if the punch cannot conduct punching, the complete set needs to be replaced, and the original centre distance shall be assured during the replacement.The purpose of adjusting the right and left directions of hole-punching machine5 is to punch two holes in the center of the width direction of packaging film byusing the ruler for measurement, and those experienced people can adjust it according to the situation of the finished bags; the purpose of adjusting the front and rear directions of hole-punching machine 5 is to divide the hole into two in the final cutting; when adjusting the hole-punching machine 5, do not change the front and rear relative positions of cursor detection 4 and hole-punching machine 5; the cursor detection 4 is installed on the motherboard of hole-punching machine, so it shall be integrally moved to the front and rear sides.2.7.6 Rectification detection 6 is also composed of optical fiber head, fiber amplifierand auxiliary parts; it is used to detect the edge of packaging film, and to control the motor counter-rotating of automatic rectification mechanism 7, only need to be adjusted according to the actual situation.2.7.7 “Turning on”, “turning off” and sensitivity of fiber amplifier can be adjustedaccording to the fiber amplifier’s instructions that came with the machine.3. Electronic control system3.1 Composition of electronic control system!PLCThe machine adopts CPU224 type PLC produced by Siemens Company to control the main unit (packaging machine) completely, and has the features ofaccurate control and high reliability; PLC can complete the action control of packaging machine, automatic supply and automatic rectification of packaging film, and automatic shutdown without film.!Touch screenThe machine adopts industrial man-machine interface, having a clear and simple picture; can enter all pictures to set the parameters of packaging machine and adjust its performance; easily open and close each function, and separately debug each action through the function buttons of “debugging picture”.!Temperature controller (control meter)The temperature controller chosen by this machine has the characteristics of high accuracy, reliable and durable performance, can control the temperature of each heater accurately, and change conveniently.3.2 Electronic control system distribution!Operating box: hang in front of the main unit, can move and consist of touch screen and power supply switch, connect to device box by using cables and terminal jacks, and easy to operate.!Device box (behind the main unit): install PLC, switch power supply, leakage protector, relay, electromagnetic air control valve and other components.III. Operation and utilization1. Working conditions1.1 Ambient temperature:＋15～＋401.2 Packaging material temperature:Refer to the relevant part of User Information on IMCL-500Vertical-bag Capping Automatic Liquid Packaging Machine.2. Operating instructions of electronic control system2.1 Instructions for operating panel of main control boxThe operating panel of main control box consists of touch screen,temperature control meter, and “emergency stop” button, “start/stop”button and “product feeding switch” button (see Figure 9).盖封头温度1 ——Cap sealing head temperature 1盖封头温度2 ——Cap sealing head temperature 2左纵封头温度——Left vertical sealing head temperature右纵封头温度——Right vertical sealing head temperature横封底温度——Horizontal sealing back temperature横封头温度——Horizontal sealing head temperature触摸屏——Touch screen启/停——Start/stop急停——Emergency stop供料——Product feedingFigure 9 Operating panel of main control box2.1.1 Operating picture of touch screen"This is the selection picture of main menu operating language, as shown in Figure 10.(1) Selecting “Chinese” will enter the Chinese operating picture.(2) Selecting “English” will enter the English operating picture.Figure 10"Entering the English running picture, as shown in Figure 11.Figure 11English running picture can show the packaging speed, accumulated packaging quantity and “clear” button, and opening and closing of heating, conveyer belt, rectification, alarm and code printing function. You can enter directly into other pictures from this picture.Entering the picture of “parameter setting”, as shown in Figure 12.Figure 12“Parameter setting” picture can set the coordinated parameters of various actions, to determine whether the packaging machine can be operated normally. The following describes the meaning of the parameters in the parameter picture: Horizontal sealing time delay: delay the horizontal sealing action for a few seconds after the film drawing is completed. Horizontal sealing time: action time of horizontal sealing. Drop off delay: start to control motor dropping after seeing the upper limit photo electricity for a few seconds. Rise and drop frequency: the rise and drop speed of film drawing servo motor. Cut delay: start to control cut action after seeing the upper limit photo electricity for a few seconds. Cut time: action time of cutting. Product feeding delay: start to feed after seeing the upper limit photo electricity for a few seconds. Product feeding time: action time of product feeding. Vertical sealing reset: press the stop button for a few seconds and then return the vertical sealing to the original position. Returning: return to the running picture.Note:1. Non-professional operators are forbidden to change the parameters of this picture freely.2. The parameter value of “parameter picture” in the packaging machine shall backup in the form of pictures or texts, to avoid the loss of parameters if the machine electricity is off for a long time.• Entering the manual picture can operate and test single action of thepackaging machine (as shown in Figure 13).Figure 13Note: when operating this picture, you cannot press two buttons ormore buttons at the same time, to avoid the mechanism collision ofpackaging machine and the damage to the machine parts.•Enter “alarm picture”, as shown in Figure 14Figure 14(1) The paperless alarm of packaging machine: when the packaging film is usedup, the alarm picture will pop up and shut down automatically, the lightwill flash, prompting there is no packaging film, and the user must stop the machine for replacing the film.(2) Photoelectric alarm: in the track state, if the cursor has not be detected threetimes in succession, the alarm picture will pop up and shut down automatically,the light will flash, prompting the user needs to check the photoelectric position or the location of packaging film, and can press “alarm reset” to release the alarm after determining the failure reason.(3) Returning: return to the running picture3. Operation specification and method3.1 Installation of the packing machine3.1.1 Check the following items after unpacking!Check the parts according to the Appendix 6 Packing List of the manual, and check whether the documents are complete or not.!Check whether the packing machine is damaged or damaged affecting the usage in the transportation process or not.3.1.2 Installation work!According to Figure1, the installation of all parts of the packing machine should be aligned, and fasten the connecting bolts. Adjust the bearing screw to make 4 casters of the host rack away from the ground, and make the packing machine in the steady state.!Pipelines connecting with all gas pipes and circuits.!After finding out AC220V, 50HZ, connect the power line of the packing machine to the power of the grounding device well and reliably.!Connect the gas source and the pressure regulator connector of the packing machine.3.2 Power on ready3.2.1 The operator must understand and master this manual, and be familiar withthe performance, operation and adjustment method.3.2.2 Before power on, check the positions of all agencies are correct, themovement mechanisms are flexible and the ，fasteners and the connectors are loosened or not, and remove and clean the foreign bodies, oil, dust and so on.3.2.3 Install the packaging film in the middle of the film roll, and complete thetransmembrane work by the Appendix 5 Transmembrane schematic diagram.3.2.4 The adjustment method of the pneumatic two linkage pieces (refer toFigure 15): Lift the pressure regulator knob 1 of the two linkage pieces,and rotate the knob to close counter-clockwise. After starting the aircompressor to 0.7MPa, open the air supply valve, rotate the pressureregulator knob 1 on the two linkage pieces clockwise, and press the knobuntil the pointer of the air pressure meter 3 to the position of 0.65MPa.Note: Press the water drain valve to release the water and drain the sewage.Figure 153.2.5 Replace the character printing the production date or lot number of the thermalcoder, install the needed production date or lot number, and check whether the print colored tape is run out or not (the installation of the characters and replacement of the colored tape refer to the manual of the thermal coder).3.2.6 Check the inside cover of the electromagnetic vibration feeder reservoir cover isfill or not, if it is not enough, supplement it.3.3 Power on trial operation3.3.1 Rotate the power switch clockwise, so that the host connects the power, at thistime, the packing machine is in the standby mode.3.3.2 Parameters setting（1）Setting of each end head, back cover temperatureSet the value of all temperature control meter in the operating box, and implement the approximate setting according to the features of the packing materials by the debugging or previous experiences. This temperature control meter has the memory function, after setting the value once, do not need to set the value in the next time, and implement the minor adjustment according to the actual situations.（2）Thermal coding temperature settingThe thermal coding temperature should be set by rotating the temperature control knob on the thermal coder according to the actual situation.（3）Parameters settingThe parameters have been set before delivery or debugging by the after-sale personnel, if the data is not lost, do not need to set it.3.3.3 Adjustment of the cursor detection sensitivity. Adjust it according to thesupplied fiber amplifier manual, and the after-sale personnel shall explain itby sound.3.3.4 Packaging empty bag test and inspection.3.3.4.1 Operate on the touch screen Operating Screen, and open the “heating” button,“correction” button, “coding” button and “conveyor belt” button. Start the aircompressor until the pressure reaches 0.7Mpa, open the intake valve androtate the reducing pressure valve to 0.65Mpa. When all sealing machinesreach the set temperature (need about 15min~20min), implement the emptypackaging bag test (note: if need single test for the packaging machine,operate it on the touch screen Manual Screen).3.3.4.2 Press the “Start/Stop” button on the operation box, and the packagingmachine enters the working state.Implement the following inspections for the empty bags:!Check the sealing quality of the empty bag by tearing method, and observe whether the sealing is firmly or not.!Check the integrity of the empty bag. Observe whether the cutting position is appropriate, the bag shape is intact or not. If it is not appropriate, adjust it.!Check whether the printed production date or lot number is clear or not, if it is not clear, increase the heating time of the print head.After the empty packaging bag passing the inspection, start the machine.3.4 Start for working3.4.1 Press the “feeding” button on the operation box.3.4.2 Press the “Start/stop” button on the operation box for trial packaging, andcheck the packaging quality, sealing quality and measurement accuracy ofthe finished bags. If the packaging capacity, sealing quality, measurementaccuracy do not meet the requirements, adjust it by pressing “Start/Stop”button on the operation box again.3.4.3 After normal operating, sample the sealing quality, measurement accuracy,patterns of the finished bags, integrity of the bag shape, the clarity of theprinted production date or lot number, if find the problems, stop themachine for adjustment.3.5 Stop the machine to complete the work3.5.1 Press the “Start/Stop” button on the operation box, the packing machineshall stop working.3.5.2 Turn off the “heating” button, “correction” button, “coding” button and“conveyor belt” button on the Operating Screen.3.5.3 Cut off the power by the power switch of the counterclockwise rotationdevices box.3.5.4 Tune the barometer of the pneumatic two linkage pieces to zero, and closethe air supply valve. Turn off the power supply switch of the air compressor,and the compressor shall stop to work.3.5.5 Clean all parts, remove the debris, and clean the feeding system.4. Notes4.1 Before use the packing machine, connect the ground wire strictly, empty thewater in the compressor tank, water and dust in the micro frog separator, at the same time, press the pneumatic two linkage pieces water drain valve (Figure 15) to drain the water.4.2 When the packing machine is working normally, prohibit putting the handsor hard object into the longitudinal and horizontal cutting bodies, and prohibit using the hands and other goods to contact the film roll to prevent damaging the equipments and causing the danger.4.3 The longitudinal and horizontal sealing silicon rubber strip is prohibitedscratching by the sharp object to prevent damaging the rubber tape and affecting the sealing quality, replace the PTFE tape on the silicon rubber tape regularly to ensure the sealing quality of the finished packing bags and reduce the damage rate.4.4 The packaging film should not have the dust, oil, water and other substances.When the film is run out, stop the machine and install the new film in time, bond the front-end and end of the upper rolling film by the adhesive tape, and pay attention to integrity of the packaging film pattern to improve the utilization of the membrane.4.5 When the packing machine is working, pay attention that when the adhesiveposition in the packing film moves to the photoelectric switch and punching device, turn off the touch screen Automatic Operating screen “feeding”button to stop feeding after replacing the new film, recover the feeding and enter the normal operating state until the adhesive position passed the horizontal sealing cutting bodies.4.6 When the packing machine is working, the finished bag should fall into theconveyor by the gravity naturally, do not use the hands or other goods to contact it to prevent leakage and adhesion. Remove the finished bag after falling 2~3S natural cooling, do not press and impact to avoid leakage.4.7 The quality of the packaging film has the great influence on the sealingquality, and users should understand the quality requirements of the film of the manufacturer in selection (such as heat sealing, thermal bonding strength, penetration resistance, composite strength, thickness requirements, etc). The packaging film with the poor quality (such as uneven thickness, low composite strength, poor thermal sealing performance, etc) should be feedback to the film manufacturer and request to treat it properly.4.8 As the electromagnetic vibration management feeder is working in thevibration condition, pay attention to check the fasteners of all parts, if the parts are loosened, fasten them. And pay attention to inspection the board spring, if it has the cracks, replace it by the same group.4.9 When the power voltage exceeds 240V or lower than 198V transiently, thepacking machine may produce the abnormal phenomena as result of the instable voltage (automatic power off, missing actions, disordered display, etc.). At this time, turn off the power switch immediately, check the power quality, if necessary, and install the voltage stabilizer device. The time interval from each stop to the next start should not be less than 10S.4.10 Before daily work, clean the movement friction surface of the horizontalsealing cutting bodies and punching devices, remove the dirt on the surface, and fill the appropriate lubrication oil on the sliding axis of the horizontal sealing cutting bodies. All sliding and rotating parts should be filled the lubrication regularly.4.11 Adjust the air source pressure each time, rotate the pneumatic two linkagepieces regulator knob to the closed position, and allow to open the pressure regulator knob to the working pressure 0.65Mpa of the packing machine until the pressure of the air compressor tank is more than or equal to0.7Mpa.4.12 Use the soft cloth to wipe the dirt on the molding surface and guide rollersurface, and clean the oil and liquid mark on the film roll.4.13 When the room temperature is lower than +100C, do not start the machinefor working to prevent damaging the cylinder and resulting in the malfunctions, if the cylinder is leaked, repair or replace it in time.4.14 When the machine is shutdown for a long time, start the machine every 30days, the starting pressure is 0.7Mpa, after two working loops, turn the pressure to 0.65Mpa, and stop the machine after working for 10min.。
热收缩包装机操作规程
热收缩包装机操作规程热收缩包装机是一种常见的包装设备，用于将产品包装在包装膜中，并通过热收缩使包装膜紧密贴合产品表面。
为了确保安全和高效的操作，以下是热收缩包装机的操作规程。
1.检查设备- 在操作热收缩包装机之前，确保设备处于正常状态。
检查电源线和电气接线是否完好无损。
- 检查机器的运行部件，如传动带、切割刀等是否损坏或松动。
- 清理和维护工作区域，确保设备周围无障碍物和杂物。
2.准备包装膜- 根据产品要求，选择适当的包装膜，并确保包装膜符合相关标准和要求。
- 检查包装膜是否有损坏，如有损坏应及时更换。
3.调整设备参数- 根据产品和包装膜的尺寸，调整热收缩包装机的参数，如包装膜长度、温度、速度等。
- 确保调整参数前先关闭电源，以免发生意外。
4.启动设备- 确保设备周围没有人员或障碍物，按下启动按钮，启动热收缩包装机。
- 观察机器的运行情况，确保各个部件正常工作，如传动带是否正常输送包装膜等。
5.放置产品- 将待包装的产品放置在机器的输送带上，确保产品合理摆放，避免堆叠或重叠。
- 在放置产品前，确保产品表面清洁干燥，以免影响包装效果。
6.启动收缩- 当产品通过热收缩所需的温度区域时，包装膜会通过热收缩装置进行收缩。
- 当包装膜完全收缩并与产品贴合时，自动切割装置会切割多余的包装膜。
7.检查包装效果- 取下包装好的产品，检查包装膜的贴合度和收缩效果，确保符合产品要求。
- 如果发现包装膜贴合度不够或有其他质量问题，应及时调整设备参数或更换包装膜。
8.清洁和维护- 关闭电源后，清洁和维护设备。
清理各个部件和转动部位的灰尘和污垢，以确保设备的正常运行。
- 定期检查设备的关键部件和连接件，如切割刀、热收缩装置等，确保其工作正常。
9.安全注意事项- 在操作热收缩包装机时，必须严格遵守相关安全操作规程，并佩戴必要的个人防护设备，如手套和护目镜。
- 注意设备的电气安全，保持设备周围干燥，避免水和其他液体接触设备。
SACMATIC 500BM——最新的四边封包装机
书山有路勤为径；学海无涯苦作舟SACMATIC 500BM——最新的四边封包装机SACMATIC 500BM是一种最新的四边封包装机，它可取代有局限的、过时的Lbar密封器。
SACMATIC 500BM采取紧密的运作模式，与其可包装几米长大型产品的能力相比，其安装空间相对较小。
SACMATIC 500BM可以实现交叉密封棒限定范围内产品的全自动包装。
由操作员或自动进料生产线将产品放在机器传送带上，然后用一支光电管隔开产品，随后产品被送入一个管状薄膜(也是这款机器制成的)，然后开始包装。
产品在管状薄膜中由不锈钢半月形板持续密封，整个过程全自动。
然后交叉密封棒会在空气作用下驱动、密封、切割管状膜。
是什幺使得SACMATIC 500BM与众不同？速度快：SACMATIC 500BM是速度很快的全自动四边封机。
产量取决于所包装产品的长度和高度，因为越高的产品需要更长的长度间隔。
假如按产品长度400mm计算，当传送带以最大速度运行、纵向密封速度为每分钟6米和12米时，机器的平均产量为每分钟13～26包。
智能控制：因其使用智能软件，SACMATIC 500BM的所有功能都能轻易的通过电子控制板进行控制，各种聚烯烃膜（包括一些辐射膜）都能应用其密封系统。
易于转换不同包装尺寸：操作员可以根据所需包装产品的宽度用手轮调整进料传送带的入口导杆，然后使用第二只手轮调整四边焊接仪器的宽度。
最后操作员再按照产品包装尺寸调整四边密封系统的高度，用开关在产品中间纵向焊接。
语音警告停止机器运行：为了防止安全隐患，保证操作安全简易，延长机器寿命，通过电子控制板上的书面显示，在下列情况下语音警告停止专注下一代成长，为了孩子。
热收缩机
啤酒热收缩膜包装机
• 产品别名：矿泉水包装机,矿泉水收缩机,啤酒热收缩膜包装机,饮料热缩包装机
• • • • • • • • • • • • • • • •
设备型号：YSBL-5040B型 产品说明： 啤酒热收缩膜包装机适用于易拉罐，矿泉水，啤酒，玻璃瓶，饮料等各种瓶的无底托或有底托热收缩包装； 同时与恒温PE收缩机配套 使用，使物品达到完美的包装效果； 啤酒热收缩膜包装机采用德国先进工艺，其主要配件均采用国外知名品牌； 整机性能稳定，使用寿命长。 技术参数 型号 YSBB-6040 型号 YSBS-5040 电源电压 220V 50/60HZ 电源电压 220V/380V 50/60HZ 功率 1.8 KW 功率 22 KW 包装速度 2 - 5 pcs/minute 包装速度 0 -10 m/minute 载重量 30 Kg 炉道尺寸 1800*600*400mm 膜宽/厚度 Max500mm/0.04-0.12mm 载重量 25KG 最大包装尺寸 450×270×350 mm ? ? 最小包装尺寸 250×50×60 mm 适用收缩膜 PE、POF、PVC、PP膜 机器外型尺寸 1020×830×1980 mm 机器外型尺寸 2800×840×1375mm 机器重量 数型号ysbp5040ysbp6040传送带宽465mm565mm收缩炉长15001800mm15001800mm炉室尺寸500400mm600400mm入口长度200mm200mm出口长度800mm800mm电压功率380v18kw380v22kw机器尺寸250028006901075mm重量220kg250kg270kg300kg品牌豫盛豫盛????????????????250028008401375mmpof热收缩包装机?设备名称
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
用途：
适用于软件、食品、化妆品、印刷、制药及地板、陶瓷、饮料、五金等行业的特大批量产品的收缩包装。
性能特点：
1.采用进口触摸屏，名种设置、操作均可在触摸屏上轻松完成。
同时可提前贮存多种产品数据，使用时只需从电脑里调出参数即可。
2.根据设备的不同配置及产品的不同特性，包装速度可以达到30～80包/分钟。
3.封切由伺服马达控制，保证封切定位精确及封切线条优良。
双联杆机构，确保较宽的封刀长期使用能保持稳定。
恒温加热封切系统可用于封切PE、POF 等各种工业标准的收缩膜。
4.可调速的前端进料系统，及后端的储物工作平台，使整机动作真正实现高速无人化自动运行。
5.BM-500L高速热风循环收缩炉采用滚轴式输送带、滚筒外包耐高温硅胶
管，每根均可以自由转动，也可以选用特弗龙网状输送带或不锈钢输送网。
6.炉内温度均匀，可适用于收缩PE、PVC、POF等不同材料的收缩膜。
7.炉内隔热内胆形成热风循环，针对不同包装物的包装需要，调整输送带的
快慢，以达到最佳的收缩效果。
主要技术参数：
型号KD-450KD-500L
最大包装尺寸(L)不限 (W+H)≤400mm (H)≤130mm(L)1500×(W)450×(H)250mm
最大封口尺寸(W+H)≤450mm(L)1500×(W)500×(H)300mm(炉腔尺寸)包装速度30～80包/分钟30～80包/分钟
电源及总功率E380V/50Hz 3kw380V/50Hz 16kw
最大电流10 A32A
使用气源 5.5kg/cm3/
机器重量800kg650kg
机器外形尺寸(L)2050×(W)1500×(H)1300mm(L)1800×(W)1100×(H)1300mm。