纸机各部联锁2

传动侧夹紧 一次臂在上部位置 无锁定锁夹紧打开控制 纸轴启动器脱开与否 联锁状态 卷纸缸允许爬行和运行 液压ok 干部润滑ok 急停ok 卷取启动器允许启动 压力ok 急停ok 一次臂换辊位置 操作侧夹紧 传动侧夹紧 操作侧一次臂有辊 传动侧一次臂有辊 一次臂在上澡位置 无夹钩打开控制 启动允许 联锁状态 液压ok 急停ok 纸轴在操作侧一次臂上 纸轴在传作侧一次臂上 一次臂不在换辊位置 夹钩没有闭合 一次臂在上面 操作侧夹钩闭合 传动侧夹钩闭合 纸辊启动器运行 急停ok 手动换辊 纸辊启动器按钮打开 纸辊启动器按钮断开 自动换辊 选择自动换辊模式 turn-up pos reel drum stop starter stop
armsangletransmf一次臂至轨道联锁状态液压ok急停ok一次臂不在换辊位置操作侧二次臂在推出位置传动侧二次臂在推出位置一次臂操作不在下面位置操作侧夹钩闭合传动侧夹钩闭合没有夹钩打开控制一次臂不在上面位置释放没有在强迫控制角度传感器故障onmanualturnuppriarmsdownpushbuttonpriarmsstoppushbuttonpriarmsuppushbutton手动换辊一次臂向下按钮一次臂停止按钮一次臂向上按钮torail自动换辊选择自动模式换辊完成辊在操作侧抱闸位置辊在传动侧抱闸位置automaticmodeselectedturnupcompletedspoolonbrakestationtsspoolonbrakestationds八
close
loading on
‘-0.5--0.5 12.8--19.2MPA 1.8--2.2MPA 15KN/M--140KN/M -1至19MPA
卷取联锁
一.Reel drum run permit on Interlocking state Reel drum crawl and run is allowed Hydraulic ok Dry end lubrication ok Emergency stop ok Reel spool starter drive allowed Hydraulic ok Emergency stop ok Primary arms above change pos Clamps close TS 卷取缸联锁 联锁状态 卷取缸允许爬行和运行 压力ok 干部润滑ok 急停停ok 纸轴启动器允许启动 压力ok 急停ok 一次臂在换辊位置 操作侧夹紧 reel drum stop starter 0度 压区试验按钮 压区闭合按钮 供给压力ok 快速打开按钮 快速释放 快速打开 急停 操作或传动侧控制压力 加载液压 操作与传动侧位置差 加载缸移动（从上） sym辊转动 sym辊液压 热辊转动 压区打开按钮 两端温度ok 主阀打开（泵前阀） 纸幅打断 背压ok 选择压区帮助加压 联锁状态 压区闭合 压区闭合控制 加压复位 操作/传动侧压力差在范围 急停 设定/实际值差在报警范围 系统压力设定/测量在范围 线压力在范围内 实际压力在范围内（TS） 实际压力在范围内（DS） SYM 辊迅速释放 快速打开 压区闭合按钮 压区打开按钮 快速打开按钮 压区加载按钮
Clamps close DS Primary arms up position No locking clamps open control 二.Spool starter off Interlocking state Reel drum carwl and run is allowed Hydraulic ok Dry end lubrication ok Emergency stop ok Reel spool starter drive allowed Hydraulic ok Emergency stop ok Primary arms above change pos Clamps close TS Clamps close DS Spool on primary arms TS spool on primary arms DS Primary arms up position No locking clamps open control 三.Start permission Interlocking state Hydraulic ok Emergency stop ok Reel spool on primary arms TS Reel spool on primary arms DS No pr.arms to rurn-up pos control No lock clamps close control Primary arms up TS Locking clamps close TS Locking clamps close DS Reel spool starter turning control on Emergency stop ok On manual turn-up Reel spool starter on push button Reel spool starter off push button On automatic turn-up Automatic mode selected Turn-up prealarm 四.pri. Arms to turn-up pos Interlocking state Hydraulic ok Emergency stop ok Pri.arms above turn-up position Locking clamps close TS Locking clamps close DS No lock clamps open control Reel spool starter speed match Reel spool relief in fixed value No pri.arms angle transm fault No manual turn-up Pri. arms down push button
heating permission heating ramp ready
closed
Nip test Web break pm. Tr ret oil temp ＜90℃ Nip test button Nip close button Feed pressure ok Qiuck open button Qiuck release Qiuck opening Emengency stop Control voltage TS&DS Loading hydraulics TS/DS pos. diff ok Load cyl. moves from up Sym. Roll rotating Sym. Roll hydraulics Thermo roll rotating Nip open button Edges temperature ok Main valve open Web cutting Counter pressure ok Opti nip help nip loading Interlockings state Nip closed Nip close control Loading reset TS/DS press. Diff.＞ max Emergency stop Alf diff. Set/Act＞max Sym press set/Act.＞max Alf ＞max (Alarm Line Force) Act. Press＞ max TS Act. Press＞ max DS Sym. Roll quick release Quick open Nip close button Nip open button Quick open button Nip load button
热/冷辊控制选择压区帮助 联锁状态 在加热过程中冷却允许 冷却选定 加热选定 sym.辊运行 热辊运行 热油流量ok 热辊油流量ok 热油系统急停 冷却水流量ok 循环泵运行 加热器打开 控制电压打开 设定/测量值ok 温度ok 进出油ok 压区闭合 控制状态 压区打开 断纸保护 断纸选择 ok 有纸幅 压辊运行 上/下辊速度一致(2%) 压区闭合按钮
绿色条件满足；黄色条件不满足。
calender(压光）连锁
Opti nip roll change Condition state Thermo roll stopped Doctor service pos. Hot oil flow Cooling pump stopped Lubr main pump stopped Thermo roll change selected Lubr spare pump stopped Sym. Hydr pump1 stopped Sym. Hydr pump2 stopped Sym. Hydr pump3 stopped Sym roll stopped sym. Roll change selected Calender interlocking control Voltage control Loading hydraulics Main valve Sym roll hydraulics Heating system Cooling system Lubrication on Calender speed 压光辊更换 条件状态 热辊停止 刮刀在维修位置 热油流量 冷却泵停止 润滑主泵停止 热辊更换选择 润滑油备用泵停 SYM。液压泵1停止 SYM。液压泵2停止 SYM。液压泵3停止 sym辊（下辊）停止 sym辊更换选择（下辊） 压光联锁控制 电压控制 加载压力 主阀（指泵前阀门） sym 辊压力 加热系统 冷却系统 稀油开启 车速控制 thermo roll change sym roll change
一次臂在换辊位置 联锁状态 液压ok 急停ok 一次臂上有辊 操作侧夹钩闭合 传动侧夹钩闭合 没有夹钩打开控制 纸辊启动器速度匹配 没有一次臂角度传输错误 没有手动换辊 一次臂向下按钮
Pri. arms stop push button Pri. arms up push button No automatic turn-up Automatic mode selected Length reached Spool starter speed ok Spool starter on control 五.Secondary arms to back Interlocking state Hydraulic ok Emergency stop ok No parent roll braking Parent roll not braking station TS Parent roll not braking station DS Parent roll brake down TS Parent roll brake down DS No spool on sec. Arms and clamps close Stopper up Pri. Arms not down Automatic mode selected Secondary arms back push button Secondary arms stop push button Secondary arms front push button On automatic turn-up Automatic mode selected 六.Parent roll braking Interlocking state Hydraulic ok Parent roll on braking station TS Parent roll on braking station DS Stoppers up On automatic turn-up Pri.arms to rail control On manual turn-up Braking station brake on push button Braking station brake off push button 七.Pri. Arms to rail Interlocking state Hydraulic ok Emergency stop ok Pri. Arms not above turn-up pos Sec. Arms at eject pos TS Sec. Arms at eject pos DS Pri. Arms not down TS Locking clamps close TS Locking clamps close DS No lock clamps open control Pri. Arms not up pos Relief not force control No pri. Arms angle transm f
ok
Heating/cooling control opti nip help nip Interlocking state Cooling perm. In heat Cooling selected Heating selected Sym. Roll run Thermo roll run Oil flow ok(heater) Oil flow ok(heater roll) Hot oil system E-stop Cooling water flow ok Criculation pump run Heater on Control voltage on Set/Act. Value diff ok Temp alteration ok In/out let oil diff ok Opit nip help nip closing Control state Nip open Web break detection Fotocell selection ok Web on Nip roll running Top/Btm roll speed same Nip close button