输煤皮带常见故障原因及处理方法

输煤皮带常见故障原因及处理方法
1.皮带松动导致传动不稳定，应及时调整皮带张紧度。

The loose belt causes unstable transmission, and the belt tension should be adjusted in time.
2.皮带老化变形，需更换新的皮带。

The belt aging and deformation, and need to replace with
a new belt.
3.皮带受到外部物体损坏，应当修补或更换。

The belt is damaged by external objects, it should be repaired or replaced.
4.皮带接头破损，应立即更换接头。

The belt joint is damaged, and the joint should be replaced immediately.
5.输煤皮带运行时有异响，可能是轴承损坏，需要检修。

There is abnormal noise during the operation of the coal conveyor belt, which may be caused by bearing damage, and it needs to be overhauled.
6.皮带轮轴承磨损，应更换新的轴承。

The belt pulley bearing is worn, and a new bearing should be replaced.
7.输煤皮带传动滑动，应检查输煤皮带张紧度。

The coal conveyor belt slips during transmission, and the tension of the belt should be checked.
8.皮带过轻或者过重，可能导致传动不稳定，需要适当调整负载。

The belt is too light or too heavy, which may cause unstable transmission, and the load should be adjusted appropriately.
9.输煤皮带传动侧向偏移，应调整输煤皮带的位置。

The lateral offset of the coal conveyor belt should be adjusted.
10.皮带清扫器损坏，需要及时更换清扫器。

The belt cleaner is damaged, and the cleaner should be replaced in time.
11.输煤皮带堵塞，应清除堵塞物并修复输煤皮带。

The coal conveyor belt is blocked, and the blockage should be cleared and the belt should be repaired.
12.皮带张紧装置失效，应检修或更换。

The belt tensioning device is malfunctioning, and should be overhauled or replaced.
13.输煤皮带发生跑偏，应调整输煤皮带的对齐方式。

The coal conveyor belt runs off, and the alignment of the coal conveyor belt should be adjusted.
14.皮带位置不准确，可能会导致皮带跑偏，需要及时调整。

The inaccurate position of the belt may cause the belt to run off, and should be adjusted in time.
15.输煤皮带运行速度不稳定，需检查传动部件和调速器。

The running speed of the coal conveyor belt is not stable, the transmission parts and the speed regulator should be checked.
16.皮带接头拉断，需要及时更换新的接头。

The belt joint is pulled off, and a new joint should be replaced in time.
17.输煤皮带受到高温影响，需更换耐高温的皮带。

The coal conveyor belt is affected by high temperature, and a high-temperature resistant belt should be replaced.
18.皮带槽板磨损，应更换新的槽板。

The belt groove plate is worn, and a new groove plate should be replaced.
19.输煤皮带长时间运行可能导致过热，需进行冷却处理。

The long-term operation of the coal conveyor belt may cause overheating and cooling treatment is required.
20.皮带承载力不足，需更换承载力更大的皮带。

The carrying capacity of the belt is insufficient, and a belt with greater carrying capacity should be replaced.
21.输煤皮带因振动过大导致磨损，应减少振动并更换受损的部件。

The coal conveyor belt wears due to excessive vibration, and the vibration should be reduced and the damaged parts should be replaced.
22.皮带张紧力不均匀，应调整张紧力均匀。

The belt tension is uneven, and the tension should be adjusted evenly.
23.输煤皮带在运行中产生静电，需要进行静电消除处理。

The coal conveyor belt generates static electricity
during operation, and anti-static treatment is required.
24.皮带输煤速度过快过慢都会影响生产，需根据实际需要调整速度。

The speed of the coal conveyor belt is too fast or too slow, which will affect production, and the speed should be adjusted according to actual needs.
25.输煤皮带因过载长时间运行可能导致破裂，需要减少负载并及时更换输煤皮带。

The coal conveyor belt may crack due to long-term overload, and the load should be reduced and the coal conveyor belt should be replaced in time.
26.皮带轮因不平衡而损坏，需调整平衡并更换受损的皮带轮。

The belt pulley is damaged due to imbalance, and the balance should be adjusted and the damaged pulley should be replaced.
27.输煤皮带因缺乏润滑而磨损，需要定期加油润滑。

The coal conveyor belt wears due to lack of lubrication, and regular lubrication is required.
28.皮带传动带磨损，需要更换新的传动带。

The belt drive belt is worn, and a new drive belt should
be replaced.
29.输煤皮带因长时间停机而生锈，需要清除锈蚀并进行防锈处理。

The coal conveyor belt rusts due to long-term downtime, and the rust should be removed and anti-rust treatment is required.
30.皮带弯曲过大导致磨损，需调整皮带的弯曲度。

The excessive bending of the belt causes wear, and the bending of the belt should be adjusted.
31.输煤皮带因环境潮湿导致老化，需改善环境条件并更换新的皮带。

The coal conveyor belt ages due to humid environment, and the environment should be improved and a new belt should be replaced.
32.皮带悬挂系统松动，需调整悬挂系统的牢固度。

The belt suspension system is loose, and the firmness of the suspension system should be adjusted.
33.输煤皮带运行中产生尘埃，需要清洁输煤皮带和周围环境。

Dust is generated during the operation of the coal conveyor belt, and the coal conveyor belt and the surrounding environment should be cleaned.
34.皮带弯曲过度可能导致裂纹，需要减少弯曲程度。

Excessive bending of the belt may cause cracks, and the degree of bending should be reduced.
35.输煤皮带受到化学腐蚀，需要更换耐腐蚀的皮带材料。

The coal conveyor belt is chemically corroded, and the corrosion-resistant belt material should be replaced.
36.皮带运行不平稳可能导致传动部件磨损，需调整传动系统。

Unstable operation of the belt may cause wear of the transmission parts, and the transmission system should be adjusted.
37.输煤皮带传动链条破损，需要更换新的传动链条。

The coal conveyor belt drive chain is damaged, and a new drive chain should be replaced.
38.皮带接头处磨损，需修复或更换新的接头。

The belt joint is worn, and the joint should be repaired
or replaced with a new one.
39.输煤皮带运行中出现抖动，需检查皮带支撑系统。

There is shaking during the operation of the coal
conveyor belt, and the belt support system should be checked.
40.皮带输煤速度不一致，可能是驱动系统故障，需进行及时检修。

The inconsistent speed of the coal conveyor belt may be caused by a drive system failure, and timely maintenance is required.
41.输煤皮带因受到外力撞击而损坏，需进行维修或更换。

The coal conveyor belt is damaged by external force impact, and repairs or replacements are required.
42.皮带张紧装置部分失效，需要更换新的张紧装置。

Some parts of the belt tensioning device are malfunctioning, and a new tensioning device should be replaced.
43.输煤皮带扭曲变形，需更换新的皮带。

The coal conveyor belt is twisted or deformed, and a new belt should be replaced.
44.皮带发生打滑，可能是因为输煤速度过快，需适当调整速度。

The belt slips, which may be caused by excessive coal conveying speed, and the speed should be adjusted appropriately.
45.输煤皮带发生撕裂，需立即停机并更换受损的部件。

The coal conveyor belt tears, and the damaged parts should be replaced immediately after shutdown.
46.皮带驱动电机故障，需要进行电机维修或更换。

The belt drive motor fails, and the motor should be repaired or replaced.
47.输煤皮带因受到过热影响而老化，需更换新的耐热皮带。

The coal conveyor belt is aged due to overheating, and a new heat-resistant belt should be replaced.
48.皮带输煤速度波动较大，可能是因为电机供电不稳定，需检查电力系统。

The coal conveyor belt has large speed fluctuations, which may be caused by unstable motor power supply, and the power system should be checked.
49.输煤皮带发生断裂，需要停机处理并更换新的输煤皮带。

The coal conveyor belt breaks, and the belt should be stopped for treatment and a new coal conveyor belt should be replaced.
50.皮带张紧机构卡滞，需及时检修并解决卡滞问题。

The belt tensioning mechanism is stuck, and it should be checked and the stuck problem should be solved in time.
51.输煤皮带因长期使用而老化，需要进行全面更换。

The coal conveyor belt is aged due to long-term use, and comprehensive replacement is required.
52.皮带打滑严重，可能是因为皮带接触面积过小，需调整接触面积。

The belt slips severely, which may be caused by too small contact area of the belt, and the contact area should be adjusted.
53.输煤皮带因受到破碎物体冲击而损坏，需进行维修或更换。

The coal conveyor belt is damaged by impact of broken objects, and repairs or replacements are required.。