5082-5703-EG000中文资料

5082-5723-FJ000中文资料

14.2 mm (0.56 inch)Seven Segment Displays Technical DataFeatures• Industry Standard Size • Industry Standard Pinout 15.24 mm (0.6 in.) DIP Leads on 2.54 mm (0.1 in.) Centers • Choice of ColorsAlGaAs Red, High Efficiency Red, Yellow, Green, Orange • Excellent Appearance Evenly Lighted Segments Mitered Corners on Segments Gray Package Gives Optimum Contrast±50° Viewing Angle • Design FlexibilityCommon Anode or Common CathodeSingle and Dual Digits Right Hand Decimal Point ±1. Overflow Character• Categorized for Luminous IntensityYellow and Green Categorized for ColorUse of Like Categories Yields a Uniform Display • High Light Output • High Peak Current• Excellent for Long Digit String Multiplexing • Intensity and Color Selection OptionSee Intensity and ColorSelected Displays Data Sheet • Sunlight Viewable AlGaAsDescriptionThe 14.2 mm (0.56 inch) LED seven segment displays aredesigned for viewing distances upto 7 metres (23 feet). Thesedevices use an industry standard size package and pinout. Both the numeric and ±1 overflow devices feature a right hand decimalpoint. All devices are available as either common anode or common cathode.Orange AlGaAs Red HERYellowGreen Package HDSP-HDSP-[1]HDSP-[1]HDSP-HDSP- DescriptionDrawingH401H151550157015601Common Anode Right Hand Decimal A H403H153550357035603Common Cathode Right Hand Decimal B H157550757075607Common Anode ±1. Overflow C H158550857085608Common Cathode ±1. OverflowD K401552157215621Two Digit Common Anode Right Hand DecimalE K403552357235623Two Digit Common Cathode Right Hand DecimalFDevicesNote:1. These displays are recommended for high ambient light operation. Please refer to the HDSP-H10X/K12X AlGaAs and HDSP-555X HER data sheet for low current operation.HDSP-K40x Series HDSP-550x Series HDSP-552x Series HDSP-560x Series HDSP-562x Series HDSP-570x Series HDSP-572x Series HDSP-H15x Series HDSP-H40x SeriesThese displays are ideal for most applications. Pin for pin equivalent displays are alsoavailable in a low current design.The low current displays are idealfor portable applications. For additional information see the Low Current Seven Segment Displays data sheet.Part Numbering SystemNotes:1. For codes not listed in the figure above, please refer to the respective datasheet or contact your nearest Agilent representative for details.2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically restricted to 1bin per tube (exceptions may apply). Please refer to respective datasheet for specific bin limit information.5082 -X X X X-X X X X X HDSP-X X X X-X X X X XMechanical Options [1]00: No Mechanical Option Color Bin Options [1,2]0: No Color Bin LimitationMaximum Intensity Bin [1,2]0: No Maximum Intensity Bin Limitation Minimum Intensity Bin [1,2]0: No Minimum Intensity Bin Limitation Device Configuration/Color [1]1: Common Anode 3: Common CathodeDevice Specific Configuration [1]Refer to Respective DatasheetPackage [1]H: 14.2 mm (0.56 inch) Single Digit Seven Segment DisplayFUNCTIONPIN AB CDEF1CATHODE e ANODE e CATHODE c ANODE cE CATHODE NO. 1 E ANODE NO. 12CATHODE d ANODE d ANODE c, d CATHODE c, d D CATHODE NO. 1 D ANODE NO. 13ANODE [3]CATHODE [4]CATHODE b ANODE bC CATHODE NO. 1 C ANODE NO. 14CATHODE c ANODE c ANODE a, b, DP CATHODE a, b, DP DP CATHODE NO. 1DP ANODE NO. 15CATHODE DP ANODE DP CATHOPDE DP ANODE DE E CATHODE NO. 1 E ANODE NO. 26CATHODE b ANODE b CATHODE a ANODE aD CATHODE NO. 2 D ANODE NO. 27CATHODE a ANODE a ANODE a, b, DP CATHODE a, b, DP G CATHODE NO. 2G ANODE NO. 28ANODE [3]CATHODE [4]ANODE c, d CATHODE c, d C CATHODE NO. 2 C ANODE NO. 29CATHODE f ANODE f CATHODE d ANODE d DP CATHODE NO. 2DP ANODE NO. 210CATHODE g ANODE g NO PINNO PINB CATHODE NO. 2 B ANODE NO. 211 A CATHODE NO. 2 A ANODE NO. 212 F CATHODE NO. 2 F ANODE NO. 213DIGIT NO. 2 ANODE DIGIT NO. 2 CATHODE 14DIGIT NO. 1 ANODE DIGIT NO. 1 CATHODE 15 B CATHODE NO. 1 B ANODE NO. 116 A CATHODE NO. 1 A ANODE NO. 117G CATHODE NO. 1G ANODE NO. 118F CATHODE NO. 1 F ANODE NO. 1NOTES:1. ALL DIMENSIONS IN MILLIMETRES (INCHES).2. ALL UNTOLERANCED DIMENSIONS ARE FOR REFERENCE ONLY.3. REDUNDANT ANODES.4. REDUNDANT CATHODES.5. FOR HDSP-5600/-5700 SERIES PRODUCT ONLY.Package DimensionsInternal Circuit DiagramNotes:1. See Figure 2 to establish pulsed conditions.2. Derate above 46°C at 0.54 mA/°C.3. See Figure 7 to establish pulsed conditions.4. Derate above 53°C at 0.45 mA/°C.5. See Figure 8 to establish pulsed conditions.HER/Orange HDSP-5500AlGaAs Red HDSP-H40x Yellow Green HDSP-H150HDSP-K40x HDSP-5700HDSP-5600 Description SeriesSeriesSeriesSeriesUnits Average Power per Segment or DP 9610580105mW Peak Forward Current per 160[1]90[3]60[5]90[7]mA Segment or DPDC Forward Current per Segment or DP 40[2]30[4]20[6]3018]mA Operating Temperature Range -20 to +100[9]-40 to +100°C Storage Temperature Range -55 to +100°C Reverse Voltage per Segment or DP 3.0V Lead Solder Temperature for 3 Seconds 260°C(1.60 mm [0.063 in.] below seating plane)Absolute Maximum Ratings6. Derate above 81°C at 0.52 mA/°C.7. See Figure 9 to establish pulsed conditions.8. Derate above 39°C at 0.37 mA/°C.9. For operation below -20°C, contact your local Agilent components sales office or an authorized distributor.Electrical/Optical Characteristics at T A = 25°CAlGaAs RedDeviceSeriesHDSP- Parameter Symbol Min.Typ.Max.Units Test Conditions Luminous Intensity/Segment[1,2,5]I V9.116.0mcd I F = 20 mA(Digit Average)1.8I F = 20 mAForward Voltage/Segment or DP V F V2.03.0I F = 100 mAH15XPeak WavelengthλPEAK645nmDominant Wavelength[3]λd637nmReverse Voltage/Segment or DP[4]V R 3.015V I R = 100 µATemperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DPThermal Resistance LED Junction-RθJ-Pin400°C/W/to-Pin SegHigh Efficiency RedDeviceSeriesHDSP- Parameter Symbol Min.Typ.Max.Units Test Conditions9002800I F = 10 mA Luminous Intensity/Segment[1,2,6]I Vµcd(Digit Average)3700I F = 60 mA Peak:1 of 6 dfForward Voltage/Segment or DP V F 2.1 2.5V I F = 20 mA 55XXPeak WavelengthλPEAK635nmDominant Wavelength[3]λd626nmReverse Voltage/Segment or DP[4]V R 3.030V I R = 100 µATemperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DPThermal Resistance LED Junction-RθJ-Pin345°C/W/to-Pin SegYellowDeviceSeriesHDSP- Parameter Symbol Min.Typ.Max.Units Test Conditions6001800I F = 10 mA Luminous Intensity/Segment[1,2]I Vµcd(Digit Average)2750I F = 60 mA Peak:1 of 6 dfForward Voltage/Segment or DP V F 2.1 2.5V I F = 20 mA 57XXPeak WavelengthλPEAK583nmDominant Wavelength[3,7]λd581.5586592.5nmReverse Voltage/Segment or DP[4]V R 3.040V I R = 100 µATemperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DPThermal Resistance LED Junction-RθJ-Pin345°C/W/to-Pin SegOrangeDeviceSeriesHDSP- Parameter Symbol Min.Typ.Max.Units Test Conditions Luminous Intensity/Segment I V 2.37mcd I F = 10 mA(Segment Average)[1,2]Forward Voltage/Segment or DP V F 2.1 2.5V I F = 20 mAPeak WavelengthλPEAK600nm H40x Dominant Wavelength[3]λd603nm I F = 10 mA K40x Reverse Voltage/Segment or DP[4]V R 3.030V I R = 100 µA Temperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DPThermal Resistance LED Junction-RθJ-Pin345°C/W/to-Pin SegDeviceSeries HDSP-ParameterSymbol Min.Typ.Max.UnitsTest Conditions 9002500I F = 10 mALuminous Intensity/Segment [1,2]I Vµcd(Digit Average)`3100I F = 60 mA Peak:1 of 6 df Forward Voltage/Segment or DPV F 2.1 2.5V I F = 10 mA56XXPeak Wavelength λPEAK 566nm Dominant Wavelength [3,7]λd 571577nm Reverse Voltage/Segment or DP [4]V R 3.050V I R = 100 µATemperature Coefficient of ∆V F /°C -2mV/°C V F /Segment or DPThermal Resistance LED Junction-R θJ-Pin345°C/W/to-PinSegHigh Performance GreenNotes:1. Device case temperature is 25°C prior to the intensity measurement.2. The digits are categorized for luminous intensity. The intensity category is designated by a letter on the side of the package.3. The dominant wavelength, λd , is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device.4. Typical specification for reference only. Do not exceed absolute maximum ratings.5. For low current operation, the AlGaAs HDSP-H10X series displays are recommended. They are tested at 1 mA dc/segment and are pin for pin compatible with the HDSP-H15X series.6. For low current operation, the HER HDSP-555X series displays are recommended. They are tested at 2 mA dc/segment and are pin for pin compatible with the HDSP-550X series.7. The Yellow (HDSP-5700) and Green (HDSP-5600) displays are categorized for dominant wavelength. The category is designated by a number adjacent to the luminous intensity category letter.AlGaAs RedFigure 2. Maximum Tolerable Peak Current vs. Pulse Duration – AlGaAs Red.Figure 1. Maximum Tolerable Peak Current vs.Pulse Duration – Red.Figure 3. Maximum Allowable DC Current vs.Ambient Temperature.Figure 4. Forward Current vs.Forward Voltage.HER, Yellow, Green, OrangeFigure 7. Maximum Tolerable Peak Currentvs. Pulse Duration – HER, Orange.Figure 8. Maximum Tolerable Peak Current vs. Pulse Duration – Yellow.Figure 5. Relative Luminous Intensity vs. DC Forward Current.Figure 6. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current.I D C M A X . – M A X I M U M D C C U R R E N T P E R S E G M E N T – m AT A – AMBIENT TEMPERATURE – °C 5030102051525354045I F – F O R W A R D C U R R E N T P E R S E G M E N T – m AV F – FORWARD VOLTAGE – VR E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D T O 1 A T 20 m A )I F – FORWARD CURRENT PER SEGMENT – mA204010305152535ηP E A K – N O R M A L IZ E D R E L A T I V E E F F I C I E N C YI PEAK – PEAK FORWARD CURRENTPER SEGMENT – mA40051015202530352010090807060504030T – AMBIENT TEMPERATURE – °C AI M A X – M A X I M U M D C C U R R E N T P E R S E G M E N T – m AD C 4550110120Figure 11. Forward Current vs.Forward Voltage.Figure 9. Maximum Tolerable PeakCurrent vs. Pulse Duration – Green.Figure 10. Maximum Allowable DC Current vs.Ambient Temperature.Figure 12. Relative LuminousIntensity vs. DC Forward Current.Figure 13. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current.Electrical/OpticalFor more information onelectrical/optical characteristics,please see Application Note 1005.Contrast EnhancementFor information on contrastenhancement please see Application Note 1015.Soldering/CleaningCleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from thechlorinated hydrocarbon family(methylene chloride, trichloro–ethylene, carbon tetrachloride,etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts.For information on soldering LEDs please refer to Application Note 1027.I F – F O R W A R D C U R R E N T P E R S E G M E N T – m AV F – FORWARD VOLTAGE – VR E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D A T 10 m A )I F – DC FORWARD CURRENT – mAηV – R E L A T I V E E F F I C I E N C Y (N O R M A L I Z E D T O 1 A T 10 m A P E R S E G M EN T )0.6I PEAK – PEAK FORWARD CURRENTPER SEGMENT – mA902070801001.61.41.31.10.90.860504030100.71.01.21.5HDSP-H15x IV Bin Category Min.Max.K 9.2016.90L 13.8025.30M 20.7038.00N 31.1056.90O 46.6085.40Intensity Bin Limits (mcd)AlGaAs RedHDSP-550x/552x IV Bin Category Min.Max.E 0.91 1.67F 1.37 2.51G 2.05 3.76H 3.08 5.64I 4.628.64J 6.9312.70K 10.3919.04HERHDSP-570x/572xIV Bin Category Min.Max.D 0.61 1.11E 0.91 1.67F 1.37 2.51G 2.05 3.76H 3.08 5.64I 4.628.64J 6.9312.70K 10.3919.04YellowHDSP-560x/562x IV Bin Category Min.Max.E 0.91 1.67F 1.37 2.51G 2.05 3.76H 3.08 5.64I 4.618.46GreenColor CategoriesNote:All categories are established for classification of products. Products may not be available in all categories. Please contact your Agilent representatives for further clarification/information.10HDSP-H40x/K40x IV Bin Category Min.Max.B 0.77 1.17C 0.95 1.45D 1.19 1.82E 1.49 2.27F 1.85 2.89G 2.32 3.54H 2.904.43Orange元器件交易网元器件交易网/semiconductorsFor product information and a complete list ofdistributors, please go to our web site.For technical assistance call:Americas/Canada: +1 (800) 235-0312 or(408) 654-8675Europe: +49 (0) 6441 92460China: 10800 650 0017Hong Kong: (+65) 271 2451India, Australia, New Zealand: (+65) 271 2394Japan: (+81 3) 3335-8152(Domestic/Interna-tional), or 0120-61-1280(Domestic Only)Korea: (+65) 271 2194Malaysia, Singapore: (+65) 271 2054Taiwan: (+65) 271 2654Data subject to change.Copyright © 2002 Agilent Technologies, Inc.Obsoletes 5988-0383ENJanuary 17, 20025988-4273EN。

DIN 53505-2000中文

能多于一次超过平均值 3 邵尔 A。
附录 A
硬度试验方法的适用范围邵尔 A 依照 DIN 53505 IRHD，低硬度范围依照 DIN 53519-1，5mm 直径球 IRHD，一般硬度范围依照 DIN 53519-1，2.5mm 直径球邵尔 D 依照 DIN 53505 球印硬度依照 DIN EN ISO 2039-1 软←硬度→硬图 A．1 ：硬度试验方法的适用范围（各方法之间不存在线性关系）
附录 A 中给出了不同的硬度试验方法的适用范围的概述。
第 2 到 5 页继续
标准编号 DIN 53505：2000-08
第2页 DIN 53505：2000-08
2 引用标准
本标准包括了，通过指定日期或未指定日期引用的来自其它出版物的规定。这些参考标准在本文的相应地方被引用，并且出版物的名称在下面列出。对于指定日期的引用，只有当经过修改或修订而包括在内时，这些出版物的任何改动或修订才适用于本标准。对于未指定日期的引用，所涉及到的出版物的最新版本适用。
din51220材料试验机的一般技术要求包括检定及校准橡胶的拉伸应力应变特性的测定采用标准试样进行软橡胶的压痕硬度irhd的测定采用小试样进行软橡胶的压痕硬度irhd的测定通过测量橡胶的硬度进行结晶效应的测定橡胶的低温特性的测定原则及试验方法用来自弹性体及塑料上的试验实例进行随机样本的统计评估塑料及硬橡胶借助于硬度计邵尔硬度测定压痕硬度iso868
德国标准
邵尔 A 及邵尔 D 橡胶硬度试验
2000 年 8 月
ICS 83．060
本标准，连同 DIN EN ISO 868 1998 年 1 月版本，取代了 1987 年 6 月版本。
与国际标准化组织（ISO）所发布的标准中的习惯用法一样，自始至终采用逗号作为十进制标记。

改良山梨醇麦康凯琼脂或改良麦康凯肉汤配套试剂安全数据单说明书

化学品安全技术说明书第一部分化学品及企业标识产品中文名称：改良山梨醇麦康凯琼脂或改良麦康凯肉汤配套试剂产品英文名称：Additives for CT-Sorbitol MacConkey Agar orCT-MacConkey Broth产品编号：SR0240企业名称：广东环凯微生物科技有限公司地址：广东省广州市黄埔区广州开发区科学城神舟路788号邮编：510663公司网址电子邮件地址：*********************传真号码：************销售热线：************-8602技术热线：************-8877/8876推荐用途和限制用途：生化研究/分析第二部分危险性概述GSH危害性类别皮肤腐蚀/刺激(类别3), 呼吸过敏(类别1)；皮肤过敏(类别1)。

GSH标签要素象形图：无警示词：警告危险信息：H316 造成轻微皮肤刺激；H317 可能造成皮肤过敏反应；H334 吸入可能导致过敏或哮喘病症状或呼吸困难。

防范说明事故响应：P333 + P313 如发生皮肤刺激或皮疹：求医/就诊；P342 + P311 如有呼吸系统病症：呼叫急救中心/医生。

废弃处置：P501将内装物/容器送到批准的废物处理厂处理。

物理和化学危险目前掌握信息，没有物理或化学的危险性。

健康危害H316 造成轻微皮肤刺激；H317 可能造成皮肤过敏反应；H334吸入可能导致过敏或哮喘病症状或呼吸困难。

环境危害无数据资料。

其它危害无。

第三部分成分/组成信息混合物化学品成分：参考使用说明。

有害物质成分：化学名称CAS No. 浓度亚碲酸钾7790-58-10.25%头孢克圬79350-37-10.0005%第四部分急救措施一般信息：无特殊的措施要求。

皮肤接触：立即用清水彻底清洗。

眼睛接触：立即提起眼睑，用大量流动清水冲洗。

如不适就医。

吸入：如不适就医。

食入：如不适就医。

就医信息：出示产品使用说明或者此SDS。

常用修饰剂介绍

kh570编辑KH-570硅烷偶联剂，γ-甲基丙烯酰氧基丙基三甲氧基硅烷是一种有机官能团硅烷偶联剂，对于提高玻纤增强和含无机填料的热固性树脂能提高它们的机械电气性能，特别是通过活性游离基反应固化（如不饱和聚酯，聚氨酯和丙烯酸酯）的热塑性树脂的填充，包括聚烯烃和热塑性聚氨酯。

国外对应牌号：A-174（美国联合碳化物公司）KBM-503（日本信越化学工业株式会社）SH-6030（美国道康宁化学公司）三、化学名称：γ-（甲基丙烯酰氧）丙基三甲氧基硅烷四、分子式：CH2=C(CH3)COOC3H6Si(OCH3)3五、典型的物理性质参数标准指标外观微黄色至无色透明液体颜色Pt-Co, ≤ 30密度（ρ 20℃，g/cm3）1.043~1.053折光率（nD 25°C）1.4285 ~1.4310沸点：255℃纯度%, ≥ 97.0溶解性硅烷偶联剂KH-570可溶于甲醇、乙醇、乙丙醇、丙酮、苯、甲苯、二甲苯,水解后在搅拌下可溶于PH=4的水中,水解产生甲醇.六、用途：主要用于改善有机材料和无机材料的粘接性能，特别适用于游离基交联的聚酯橡胶，聚烯烃、聚苯乙烯和在光敏材料中作为助剂。

七CAS NO. : 2530-85-0八特征和用途KH-570硅烷偶联剂的用途：（1）当复合材料用经过与聚酯相容的表面处理剂处理过的玻纤时，能显著提高复合材料的强度，这种表面处理剂通常包括硅烷偶联剂、成膜剂、润滑剂和抗静电剂。

（2）此产品提高填充白碳黑、玻璃、硅酸盐和金属氧化物的聚酯复合材料的干湿态机械强度。

（3）此产品提高许多无机填料填充复合材料的湿态电气性能。

例如：交联聚乙烯和聚氯乙烯。

（4）此产品可与醋酸乙烯和丙烯酸酯或甲基丙烯酸酯单体共聚合成可室温交联固化的。

这些硅烷团化聚合物广泛应用于涂料、胶粘剂和密封胶中。

提供优异的粘接力和耐久力。

一、概述：偶联剂kh570是一类具有两不同性质官能团的物质，它们分子中的一部分官能团可与有机分子反应，另一部分官能团可与无机物表面的吸附水反应，形成牢固的粘合。

艾默生表面处理代码

艾默生网络能源有限公司检验标准名称：表面处理代码图号：DMBM0.402.022拟制：何浩审核：张士杰、徐建平标准化：詹轶群IQC会签：汪长华批准：张运清修订信息表目录表面处理代码 (5)1 目的 (5)2 适用范围 (5)3 关键词 (5)4 引用/参考标准或资料 (5)5 规范内容 (5)5.1 术语 (5)5.2 技术说明 (6)5.3 备注 (6)表面处理代码1 目的本标准规定了图纸中标注表面处理时所用的代码内容，并说明了每种工艺所对应的技术要求以及每种外观要求应采用的标准样板。

2 适用范围本标准适用于艾默生网络能源有限公司产品的结构件零件、组合件的设计及图纸标注和后续的采购、生产、检验。

3 关键词表面处理电镀喷漆粉末喷涂标准代码4 引用/参考标准或资料下列标准包含的条文，通过在本标准中引用而构成本标准的条文。

在标准出版时，所示版本均为有效。

所有标准都会被修订，使用本标准的各方应探讨使用下列标准最新版本的可能性。

DMBM0.402.003表面处理通用检验标准DMBM0.487.006 环氧玻璃布层压板检验标准DMBM0.402.001 产品表面外观缺陷的限定标准5 规范内容5.1 术语5.1.1 组合件：指用铆接、搭接、胶接、点焊、或压配合等类似方法组装在一起的部件。

5.1.2 无色阳极化：即无色硫酸阳极化（纯水封闭）。

5.1.3 光亮阳极化：即化学抛光后再进行无色硫酸阳极化处理。

5.1.4 喷砂光亮阳极化：即先喷砂再进行光亮阳极化处理。

5.1.5 黑色阳极化：即硫酸阳极化着黑色。

5.1.6 金黄色阳极化：即硫酸阳极化着金黄色。

5.1.7 喷砂光亮黑色阳极化：即先喷砂再进行化学抛光及黑色阳极化。

5.1.8 光亮无色化学氧化：即先化学抛光后再进行无色化学氧化处理。

5.1.9 喷砂光亮无色化学氧化：即先喷砂处理再进行光亮无色化学氧化。

5.2 技术说明5.2.1 表面处理代码以字母加数字表示。

5082-B03G-0L000中文资料

DescriptionThe 18:88 and 88:88 0.56" Four Digit Seven Segment Displays have surface painted in neutral gray and black for enhanced on/off contrast. All devices are available in either common anode or common cathode configuration with tinted green segments or untinted segments.Agilent HDSP-B0xG18:88 and 88:88 0.56" Four Digit GaP Green Seven Segment DisplayData SheetFeatures•Excellent appearance•Evenly illuminated segments•Gray face for optimum on/offcontrast•Choice of colors: Green•Choice of character size:0.56 inchFRONT SIDE2 – ∅1.70RIGHT SIDEA A A DDD C F EF E F EB CB C B C GGGDP3DP2DIGIT 2DIGIT 3DIGIT 4DIGIT 1AF EB G D NOTE:ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).UNLESS OTHERWISE STATED, TOLERANCES ARE ± 0.25 mm.Pin Configuration Function Pin HDSP-B01G/B03G/B05G/B07G/B09G HDSP-B02G/B04G/B06G/B08G/B10G 1Anode E Cathode E 2Anode D Cathode D 3Anode DP Cathode DP 4Anode C Cathode C 5Anode GCathode G6Digit 4 Common Cathode Digit 4 Common Anode 7Anode BCathode B8Digit 3 Common Cathode Digit 3 Common Anode 9Digit 2 Common Cathode Digit 2 Common Anode 10Anode F Cathode F 11Anode ACathode A12Digit 1 Common CathodeDigit 1 Common AnodeFRONT SIDE2 – ∅1.70RIGHT SIDEAA A DDD B CF EF E F EB CB C B C GGGDP3DP2DIGIT 2DIGIT 3DIGIT 4DIGIT 1NOTE:ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).UNLESS OTHERWISE STATED, TOLERANCES ARE ± 0.25 mm.HDSP-B01G and HDSP-B05G (Common Cathode)HDSP-B02G and HDSP-B06G (Common Anode)DIGIT 1DIGIT 2DIGIT 3DIGIT 4A 11B 7C 4D 2E 1F 10G 5DP 3DIGIT 1DIGIT 2DIGIT 3DIGIT 4A 11B 7C 4D 2E 1F 10G 5DP 3HDSP-B03G, HDSP-B07G, and HDSP-B09G (Common Cathode)HDSP-B04G, HDSP-B08G, and HDSP-B10G (Common Anode)DIGIT 1DIGIT 2DIGIT 3DIGIT 4A 11B 7C 4D 2E 1F 10G 5DP3DIGIT 1DIGIT 2DIGIT 3DIGIT 4A 11B 7C 4D 2E 1F 10G 5DP 3DevicesHDSP-DescriptionB01G88:88 0.56" Green 4 Digit, Tinted Green, Common Cathode, Display 18:88, Gray Color Surface B02G88:88 0.56" Green 4 Digit, Tinted Green, Common Anode, Display 18:88, Gray Color Surface B03G88:88 0.56" Green 4 Digit, Tinted Green, Common Cathode, Display 88:88, Gray Color Surface B04G88:88 0.56" Green 4 Digit, Tinted Green, Common Anode, Display 88:88, Gray Color Surface B05G88:88 0.56" Green 4 Digit, Untinted, Common Cathode, Display 18:88, Gray Color SurfaceB06G88:88 0.56" Green 4 Digit, Untinted, Common Anode, Display 18:88, Gray Color SurfaceB07G88:88 0.56" Green 4 Digit, Untinted, Common Cathode, Display 88:88, Gray Color SurfaceB08G88:88 0.56" Green 4 Digit, Untinted, Common Anode, Display 88:88, Gray Color SurfaceB09G88:88 0.56" Green 4 Digit, Untinted, Common Cathode, Display 88:88, Black Color SurfaceB10G88:88 0.56" Green 4 Digit, Untinted, Common Anode, Display 88:88, Black Color SurfacePart Numbering System5082 -X X X X-X X X X XHDSP-X X X X-X X X X XMechanical Options[1]00: No Mechanical OptionColor Bin Options[1,2]0: No Color Bin LimitationMaximum Intensity Bin[1,2]0: No Maximum Intensity Bin LimitationMinimum Intensity Bin[1,2]0: No Minimum Intensity Bin LimitationDevice Configuration/Color[1]G: GreenDevice Specific Configuration[1]Refer to Respective DatasheetPackage[1]Refer to Respective DatasheetNotes:1. For codes not listed in the figure above, please refer to the respective datasheet or contactyour nearest Agilent representative for details.2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typicallyrestricted to 1 bin per tube (exceptions may apply). Please refer to respective datasheet forspecific bin limit information.Electrical/Optical Characteristics at T A = 25˚C Device Series HDSP-ParameterSymbol Min.Typ.Max.Units Test Conditions Luminous Intensity/SegmentI V20003200µcd I F = 10 mA(Digit Average)32004500All DevicesForward Voltage/Segment or DP V F 1.802.20 2.60V I F = 20 mA Peak Wavelength λPEAK 568nm I F = 20 mA Dominant Wavelength λd 573nmI F = 20 mA Luminous Intensity I V-M 2:1I F = 10 mA Matching Ratio Reverse CurrentI R100µAV R = 5 VNotes:1.Typical specification for reference only. Do not exceed absolute maximum ratings.2.The dominant wavelength, λd , is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device.Absolute Maximum RatingsDescriptionGreen Units Average Power per Segment or DP65mW Peak Forward Current per Segment or DP 100mA DC Forward Current per Segment or DP 25mA Operating Temperature Range–40 to +105˚C Storage Temperature Range–40 to +105˚C Reverse Voltage per Segment or DP5V Wavesoldering Temperature for 3 seconds 2 mm below body250˚CNote:1.Derate above 40˚C at 0.33 mA/˚C for green.B01G, B02G, B03G, B04G B05G, B06G, B07G, B08G,B09G, B10G Intensity Bin Limits (µcd at 10 mA)Device Series HDSP-B01G, B02G, B03G, B04G B05G, B06G, B07G, B08G, B09G, B10GBin Name Min.[1]Max.[1]Min.[1]Max.[1]K 20003200NA NA L 3200505032005050MNA NA50508000Note:1.Tolerance for each bin limit is ±10%.Color Categories (Tolerance ± 1 nm)Rank Symbol Hue Range Unit 22573.5–576.5nm 33570.5–573.5nmContrast EnhancementFor information on contrast enhancement, please see Application Note 1015.Soldering/CleaningCleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from thechlorinated hydrocarbon family (methylene chloride,trichloroethylene, carbon tetrachloride, etc.) are notrecommended for cleaning LED parts. All these various solvents attack or dissolve theencapsulating epoxies used to form the package of plastic LED parts.Figure 1. Maximum allowable DC current vs.ambient temperature.Figure 2. Forward current vs. forward voltage.Figure 3. Relative luminous intensity vs. DC forward current.Figure 4. Relative efficiency (luminous intensity per unit current) vs. peak current.I D C – M A X I M U M D C C U R R E N T P E R S E G M E N T – m AT A – AMBIENT TEMPERATURE – °CI F – F O R W A R D C U R R E N T P E R S E G M E NT – m AV F – FORWARD VOLTAGE – VR E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D T O 1 A T 10 mA F O R G R E E N )I F – DC FORWARD CURRENT – mA8642R E L A T I V E E F F I C I E N C Y (N O R M A L I Z E D T O 1 A T 10 m A )1.4005101520253035404550PEAK FORWARD CURRENTPER SEGMENT – mA/semiconductorsFor product information and a complete list of distributors, please go to our web site.For technical assistance call:Americas/Canada: +1 (800) 235-0312 or (916) 788-6763Europe: +49 (0) 6441 92460China: 10800 650 0017Hong Kong: (+65) 6756 2394India, Australia, New Zealand: (+65) 6755 1939Japan: (+81 3) 3335-8152(Domestic/Interna-tional), or 0120-61-1280(Domestic Only)Korea: (+65) 6755 1989Singapore, Malaysia, Vietnam, Thailand,Philippines, Indonesia: (+65) 6755 2044Taiwan: (+65) 6755 1843Data subject to change.Copyright © 2004 Agilent Technologies, Inc.Obsoletes 5988-5381EN June 30, 20045988-7859EN。

5082-303A-FG000资料

DescriptionThese slim font seven segment displays incorporate a new slim font character design. This slim font features narrow width,specially mitered segments to give a fuller appearance to the illuminated character. Faces of these displays are painted aneutral gray for enhanced on/off contrast.Agilent HDSP-301x/303x Series HDSP-561x/563x Series 10 mm and 13 mm Slim Font Seven Segment DisplaysData SheetFeatures•Excellent appearance •Slim font design •Mitered corners, evenly illuminated segments•Gray face for optimum on/off contrast •Choice of colors: HER, green,yellow, and AlGaAs •Choice of character size: 10 mm and 13 mm •Characterized for luminous intensityDevices HER Green Yellow AlGaAs HDSP-HDSP-HDSP-HDSP-Description301E 301G 301Y 301A Common Anode, 10 mm Display 303E 303G 303Y 303A Common Cathode, 10 mm Display 561E 561G 561Y 561A Common Anode, 13 mm Display 563E563G563Y563ACommon Cathode, 13 mm DisplayAll devices are available in either common anode or commoncathode configuration with righthand decimal point.Part Numbering System5082- x xx x-x x x xxHDSP- x xx x-x x x xxMechanical Options[1]00: No Mechanical OptionColor Bin Options[1,2]0: No Color Bin LimitationMaximum Intensity Bin[1,2]0: No Maximum Intensity Bin LimitationMinimum Intensity Bin[1,2]0: No Minimum Intensity Bin LimitationDevice Configuration/Color[1]A: AlGaAs RedE: High Efficiency RedG: GreenY: YellowDevice Specific Configuration[1]Refer to Respective Data SheetPackage[1]Refer to Respective Data SheetNotes:1. For codes not listed in the figure above, please refer to the respective data sheet or contact your nearest Agilent representativefor details.2. Bin options refer to shippable bins for a part-number. Color and Intensity Binbs are typically restricted to 1 bin per tube(exceptions may apply). Please refer to respective data sheet for specific bin limit information.Pin Function1G2F3Common A/C 4E5D6DP7C8Common A/C 9B10A7.006.40NOTE: QDSP-399G DOES NOT HAVE PIN 6.COUNTRY TOP SIDEFRONT VIEW RIGHT SIDE0.30 ± 0.05(0.012)6.001.85Pin Function 1E 2D3Common A/C 4C 5DP 6B 7A8Common A/C 9F 10G0.29 ± 0.08 TYP.(0.011)12345(0.023)(0.141)(0.100)NOTES:1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).2. UNLESS OTHERWISE STATED, TOLERANCES ARE ±0.25 mm.Absolute Maximum RatingsDescription HER Green Yellow AlGaAs Units Average Power per Segment or DP10510510537mW Peak Forward Current per Segment or DP90909045mA DC Forward Current per Segment or DP30303015mA Operating Temperature Range–40 to +80–40 to +80–40 to +80–20 to +80˚C Storage Temperature Range–40 to +80–40 to +80–40 to +80–40 to +80˚C Reverse Voltage per Segment or DP5555V Wavesoldering Temperature for 3 Seconds250250250250˚C 1.59 mm below bodyNotes:1.Derate above 33˚C at 0.34 mA/˚C for HER.2.Derate above 27˚C at 0.32 mA/˚C for Green.3.Derate above 30˚C at 0.33 mA/˚C for Yellow.4.Derate above 60˚C at 0.25 mA/˚C for AlGaAs.Electrical/Optical Characteristics at T A = 25˚CHERDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 301/303E Luminous Intensity/Segment I V 1.251 2.000mcd I F = 10 mA (Digit Average)Forward Voltage/Segment V F 1.90 2.50V I F = 20 mAor DPPeak WavelengthλPEAK635nm I F = 20 mADominant Wavelengthλd625nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinHERDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 561/563E Luminous Intensity/Segment I V 2.001 3.526mcd I F = 10 mA (Digit Average)Forward Voltage/Segment V F 1.90 2.50V I F = 20 mAor DPPeak WavelengthλPEAK635nm I F = 20 mADominant Wavelengthλd625nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 301/303G Luminous Intensity/Segment I V 2.001 3.200mcd I F = 10 mA (digit average)Forward Voltage/Segment V F 2.25 2.50V I F = 20 mAor DPPeak WavelengthλPEAK568nm I F = 20 mADominant Wavelengthλd573nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinGreenDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 561/563G Luminous Intensity/Segment I V 3.201 5.601mcd I F = 10 mA (Digit Average)Forward Voltage/Segment V F 2.25 2.50V I F = 20 mAor DPPeak WavelengthλPEAK568nm I F = 20 mADominant Wavelengthλd573nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinYellowDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 301/303Y Luminous Intensity/Segment I V 1.251 2.000mcd I F = 10 mA (Digit Average)Forward Voltage/Segment V F 2.15 2.50V I F = 20 mAor DPPeak WavelengthλPEAK589nm I F = 20 mADominant Wavelengthλd590nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 561/563Y Luminous Intensity/Segment I V 2.00 3.526mcd I F = 10 mA (Digit Average)Forward Voltage/Segment V F 2.15 2.50V I F = 20 mAor DPPeak WavelengthλPEAK589nm I F = 20 mADominant Wavelengthλd590nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinNotes:1.Typical specification for reference only. Do not exceed absolute maximum ratings.2.The dominant wavelength, λ, is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device.AlGaAsDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 301/303A Luminous Intensity/Segment I V0.3200.505mcd I F = 1 mA (Digit Average)Forward Voltage/Segment V F 1.80 2.20V I F = 20 mAor DPPeak WavelengthλPEAK660nm I F = 20 mADominant Wavelengthλd643nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinAlGaAsDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 561/563A Luminous Intensity/Segment I V0.5060.878mcd I F = 1 mA (Digit Average)Forward Voltage/Segment V F 1.80 2.20V I F = 20 mAor DPPeak WavelengthλPEAK660nm I F = 20 mADominant Wavelengthλd643nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinNotes:1.Typical specification for reference only. Do not exceed absolute maximum ratings.2.The dominant wavelength, λ, is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device.HDSP-301E/303E/561E/563EIV Bin Category Min.Max.I 1.100 2.200K 1.800 3.600HDSP-561Y/563Y IV Bin Category Min.Max.K 1.800 3.600L 2.8005.600HDSP-301Y/303YIV Bin Category Min.Max.I 1.100 2.200K 1.8003.600HDSP-301A/303A/561A/563AIV Bin Category Min.Max.F 0.2800.560G 0.4500.900HDSP-301G/303G/561G/563GIV Bin Category Min.Max.K 1.800 3.600L 2.800 5.600Intensity Bin Limits (mcd)GreenYellowHERAlGaAs RedDominant Wavelength (nm)ColorBin Min.Max.Green 3570.00574.504567.00571.50Yellow2586.50590.003584.00587.50Color CategoriesNote:1. All categories are established for classification of products.Products may not be available in all categories. Please contact your Agilent representatives for further clarification/information.YellowFigure 1. Maximum allowable DC current vs.ambient temperature.Figure 2. Forward current vs. forward voltage.Figure 3. Relative luminous intensity vs. DC forward current.HDSP-301x/303x SeriesContrast EnhancementFor information on contrast enhancement, please see Application Note 1015.Soldering/CleaningCleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from thechlorinated hydrocarbon family (methylene chloride,Figure 4. Maximum allowable DC current vs.ambient temperature.Figure 5. Forward current vs. forward voltage.Figure 6. Relative luminous intensity vs. DC forward current.HDSP-561x/563x SeriesI D C – M A X I M U M D C C U R R E N T P E R S E G M E N T – m AT A – AMBIENT TEMPERATURE – °CI F – F O R W A R D C U R R E N TP E R S E G M E N T – m AV F – FORWARD VOLTAGE – V I D C – M A X I M U M D C C U R R E N T P E R S E G M E N T – m AT A – AMBIENT TEMPERATURE – °CI F – F O R W A R D C U R R E N TP E R S E G M E N T – m AV F – FORWARD VOLTAGE – V trichloroethylene, carbon tetrachloride, etc.) are notrecommended for cleaning LED parts. All of these varioussolvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts.For information on soldering LEDs, please refer to Application Note 1027.R E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D T O 1 A T 5 m A F O R H E R A N D Y E L L O W A N D T O 1 A T 10 m A F O R G R E E N )I F – DC FORWARD CURRENT – mA12682410R E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D T O 1 A T 5 m A F O R H E R A N D Y E L L O W A N D T O 1 A T 10 m A F O R G R E E N )I F – DC FORWARD CURRENT – mA/semiconduc-torsFor product information and a complete list of distributors, please go to our web site.For technical assistance call:Americas/Canada: +1 (800) 235-0312 or (916) 788-6763Europe: +49 (0) 6441 92460China: 10800 650 0017Hong Kong: (+65) 6756 2394India, Australia, New Zealand: (+65) 6755 1939 Japan: (+81 3) 3335-8152(Domestic/ International), or 0120-61-1280(Domestic Only) Korea: (+65) 6755 1989Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843Data subject to change.Obsoletes 5980-2919ENJuly 11, 20045988-4352EN。

5082-A411-HM000资料

DevicesAlGaAs Orange Red HER Green Package HDSP-HDSP-HDSP-HDSP- DescriptionDrawingA411A111A211A5117.6 mm Common Anode Right Hand Decimal A A413A113A213A5137.6 mm Common Cathode Right Hand Decimal B F411F111F211F51110 mm Common Anode Right Hand Decimal C F413F113F213F51310 mm Common Cathode Right Hand Decimal D G411G111G211G51110 mm Two Digit Common Anode Right Hand Decimal E G413G113G213G51310 mm Two Digit Common Cathode Right Hand Decimal F H411H111H211H51114.2 mm Common Anode Right Hand Decimal G H413H113H213H51314.2 mm Common Cathode Right Hand Decimal H K411K111K211K51114.2 mm Two Digit Common Anode Right Hand Decimal I K413K113K213K51314.2 mm Two Digit Common Cathode Right Hand DecimalJBlack Surface Seven Segment Displays Technical DataFeatures• Black Surface and Color Tinted Epoxy• Industry Standard Size • Industry Standard Pinout • Choice of Character Size 7.6 mm (0.30 in.), 10 mm (0.40in.), 14.2 mm (0.56 in.)• Choice of ColorsAlGaAs Red, High Efficiency Red (HER), Green, Orange • Excellent Appearance Evenly Lighted Segments ±50° Viewing Angle• Design FlexibilityCommon Anode or Common CathodeSingle and Two Digit• Categorized for Luminous IntensityCategorized for Color: Green Use of Like Categories Yields a Uniform Display• Excellent for Long Digit String MultiplexingDescriptionThese devices use industrystandard size package and pinout.Available with black surfaceHDSP-AX11/-AX13 Series HDSP-FX11/-FX13 Series HDSP-GX11/-GX13 Series HDSP-HX11/-HX13 Series HDSP-KX11/-KX13 Seriesfinish. All devices are available as either common anode or common cathode.Typical applications includeappliances, channel indicators of TV, CATV converters, game machines, and point of sale terminals.Part Numbering System5082 -X X X X-X X X X XHDSP-X X X X-X X X X XMechanical Options[1]00: No Mechanical OptionColor Bin Options[1,2]0: No Color Bin LimitationMaximum Intensity Bin[1,2]0: No Maximum Intensity Bin LimitationMinimum Intensity Bin[1,2]0: No Minimum Intensity Bin LimitationDevice Configuration/Color[1]1: Common Anode3: Common CathodeDevice Specific Configuration[1]Refer to Respective DatasheetPackage[1]A: 7.6 mm (0.3 inch) Single Digit Seven Segment DisplayF: 10 mm (0.4 inch) Single Digit Seven Segment DisplayG: 10 mm (0.4 inch) Dual Digit Seven Segment DisplayH: 14.2 mm (0.56 inch) Single Digit Seven Segment DisplayK: 14.2 mm (0.56 inch) Dual Digit Seven Segment Display Notes:1. For codes not listed in the figure above, please refer to the respective datasheet or contact your nearestAgilent representative for details.2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically restricted to 1bin per tube (exceptions may apply). Please refer to respective datasheet for specific bin limit information.Package Dimensions (7.6 mm Series)Internal Circuit DiagramPackage Dimensions (10 mm Series: Single)Internal Circuit DiagramPackage Dimensions (10 mm Series: Two Digit)Internal Circuit DiagramPackage Dimensions (14.2 mm Series: Single)Internal Circuit DiagramPackage Dimensions (14.2 mm Series: Two Digit)Internal Circuit Diagram2DIGIT NO. 1 CATHODE1Absolute Maximum RatingsAlGaAs Red HER/Orange GreenHDSP-X11X HDSP-X21X/X41X HDSP-X51X Description Series Series Series Units Average Power per Segment37105105mW or DPPeak Forward Current per4590[1]90[3]mA Segment or DPDC Forward Current per15[5]30[2]30[4]mA Segment or DPOperating Temperature Range–20 to +100 –40 to +100°C Storage Temperature Range–55 to +100°C Reverse Voltage per 3.0V Segment or DPWave Soldering Temperature for250°C 3 Seconds (1.60 mm [0.063 in.]below Body)Notes:1. See Figure 5 to establish pulsed conditions.2. Derate above 53°C at 0.45 mA/°C (see Figure 7).3. See Figure 6 to establish pulsed conditions.4. Derate above 39°C at 0.37 mA/°C (see Figure 7).5. Derate above 91°C at 0.53 mA/°C (see Figure 1).Electrical/Optical Characteristics at T A = 25°CAlGaAs RedDevice SeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions A11X Luminous Intensity/Segment[1,2]I V315600µcd I F = 1 mA (Digit Average)3600I F = 5 mAF11X, G11X330650I F = 1 mA3900I F = 5 mAH11X, K11X400700I F = 1 mA4200I F = 5 mAAll Devices Forward Voltage/Segment or DP V F 1.6 2.0V I F = 1 mA1.7I F = 5 mA1.822I F = 20 mA PeakPeak WavelengthλP EAK645nmDominant Wavelength[3]λd637nmReverse Voltage/Segment or DP[4]V R 3.015V I R = 100 µATemperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DPA11X Thermal Resistance LED RθJ-PIN255°C/W/Junction-to-Pin Seg.F11X, G11X320H11X, K12X400OrangeDevice SeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions A41X Luminous Intensity/Segment I V0.70mcd I F = 5 mA (Segment Average)[1,2]F41X, G41X 1.0I F = 5 mAH41X, K41X 2.37I F = 10 mAAll Forward Voltage/Segment or DP V F 2.0 2.5V I F = 20 mA DevicesPeak WavelengthλPEAK600nmDominant Wavelength[3]λd603nmReverse Voltage/Segment or DP[4]V R 3.030V I R = 100 µATemperature Coefficient of∆V F/°C–2mV/°CV F/Segment or DPA41X Thermal Resistance LED RθJ-PIN200°C/W/Junction-to-Pin Seg.F41X, G41X320H41X, K41X345High Efficiency RedDevice SeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions A21X Luminous Intensity/Segment[1,2]I V360980µcd I F = 5 mA (Digit Average)5390I F = 20 mAF21X, G21X4201200I F = 5 mAH21X, K21X9002800I F = 10 mA3700I F = 60 mA Peak:1/6 Duty Factor All Forward Voltage/Segment or DP V F 2.0 2.5V I F = 20 mA DevicesPeak WavelengthλPEAK635nmDominant Wavelength[3]λd626nmReverse Voltage/Segment or DP[4]V R 3.030V I R = 100 µATemperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DPA21X Thermal Resistance LED RθJ-PIN200°C/W/Junction-to-Pin Seg.F21X, G21X320H21X, K21X345High Performance GreenDevice SeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test ConditionsA51X Luminous Intensity/Segment[1,2]I V8603000µcd I F = 10 mA (Digit Average)6800I F = 20 mAF51X, G51X10303500I F = 10 mAH51X, K51X9002500I F = 10 mA3100I F = 60 mA Peak:1/6 Duty FactorAll Forward Voltage/Segment or DP V F 2.1 2.5V I F = 10 mADevicesPeak WavelengthλPEAK566nmDominant Wavelength[3,5]λd571577nmReverse Voltage/Segment or DP[4]V R 3.050V I R = 100 µATemperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DPA51X Thermal Resistance LED RθJ-PIN200°C/W/Junction-to-Pin Seg.F51X, G51X320H51X, G51X345Notes:1. Case temperature of device immediately prior to the intensity measurement is 25°C.2. The digits are categorized for luminous intensity. The intensity category is designated by a letter on the side of the package.3. The dominant wavelength, λd, is derived from the CIE chromaticity diagram and is that single wavelength which defines the color ofthe device.4. Typical specification for reference only. Do not exceed absolute maximum ratings.5. Green (HDSP-A51X/F51X/G51X/H512X/K51X) series displays are categorized for dominant wavelength. The category is designated bya number adjacent to the luminous intensity category letter.Figure 3. Relative Luminous Intensity vs. DC Forward Current.Figure 4. Relative Efficiency (LuminousIntensity per Unit Current) vs. Peak Current.Figure 1. Maximum Allowable Average orDC Current vs. Ambient Temperature.Figure 2. Forward Current vs. Forward Voltage.16024681012142010090807060504030T – AMBIENT TEMPERATURE – °C AI A V E . M A X – M A X I M U M A V E R A G E F O R W A R D C U R R E N T P E R S E G M E N T – m AF 1201102018F 50.020.010.05.02.01.00.50.10.51.01.52.02.5V – FORWARD VOLTAGE – VF I – F O R W A R D C U R R E N TP E R S E G M E N T – m A20105210.50.20.10.10.20.51251020R E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D T O 1 A T 1 m A )I – FORWARD CURRENT PER SEGMENT – mAF I – PEAK FORWARD CURRENTPER SEGMENT – mAPEAK η –R E L A T I V E E F F I C I E N C Y – N O R M A L I Z E D T O 1 A T 1 m AP E A K 1.31.21.11.00.90.80.7AlGaAs RedHER, Green, OrangeFigure 7. Maximum Allowable DCCurrent vs. Ambient Temperature.Figure 8. Forward Current vs.Forward Voltage Characteristics.Figure 9. Relative Luminous Intensity vs. DC Forward Current.Figure 10. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current.40051015202530352010090807060504030T – AMBIENT TEMPERATURE – °CA I M A X – M A X I M U M D C C U R R E N T P E R S E G M E N T – m AD C 1201105045010080604020I – F O R W A R D C U R R E N T P E R S E G M E N T – m AF 2.04.03.01.0V –FORWARD VOLTAGE – VF 05.0ηP E A K – R E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D T O 1 A T 5 m A F O R H E R ,A N D T O 1 A T 10 m A F O R G R E E N )150108642205301025I – FORWARD CURRENT PER SEGMENT – mAF 0I – PEAK FORWARD CURRENTPER SEGMENT – mAPEAK ηP E A K – R E L A T I V E E F F I C I E N C Y (N O R M A L I Z E D T O 1 A T 5 m A F O R H E R ,A N D 10 m A F O R G R E E N )Figure 5. Maximum Tolerable Peak Currentvs. Pulse Duration – HER, Orange.Figure 6. Maximum Tolerable Peak Current vs. Pulse Duration – Green.R A T I O O F M A X I M U M O P E R A T I N G P E A K C U R R E N T T O T E M P E R A T U R E D E R A T E D D C C U R R E N TI P E A K F I M A X D C t – PULSE DURATION – µsP 101100DC R A T I O O F M A X I M U M O P E R A T I N G P E A K C U R R E N T T O T E M P E R A T U R E D E R A T E D D C C U R R E N TI P E A K FI M A X D C t – PULSE DURATION – µs P 101100DCHDSP-A1xx IV Bin Category Min.Max.E 0.3150.520F 0.4280.759G 0.621 1.16H 0.945 1.71I 1.40 2.56J 2.10 3.84K 3.14 5.75L 4.708.55Intensity Bin Limits (mcd)AlGaAs RedHDSP-F1xx/G1xx IV Bin Category Min.Max.D 0.3910.650E 0.5320.923F 0.755 1.39G 1.13 2.08H 1.703.14HDSP-H1xx/K1xx IV Bin Category Min.Max.C 0.4150.690D 0.5650.990E 0.810 1.50F 1.20 2.20G 1.80 3.30H 2.73 5.00I 4.097.50OrangeHDSP-A41XIV Bin Category MinMaxA 0.2840.433B 0.3540.541C 0.4430.677D 0.5540.846E 0.692 1.057F 0.856 1.322G 1.082 1.652H 1.352 2.066I 1.692 2.581J 2.114 3.227K 2.641 4.034L 3.300 5.042M 4.127 6.303N 5.1577.878HDSP-F41X/G41XIV Bin Category MinMaxC 0.4850.890D 0.728 1.333E 1.091 2.000F 1.636 3.000G 2.454 4.500H 3.6826.751HDSP-H41X/K41XIV Bin Category MinMaxB 0.77 1.17C 0.95 1.45D 1.19 1.82E 1.49 2.27F 1.85 2.89G 2.32 3.54H 2.904.43Intensity Bin Limits (mcd), continued HERMin.Max.B0.3420.630C0.5160.946D0.774 1.418E 1.160 2.127F 1.740 3.190G 2.610 4.785H 3.9157.177Min.Max.C0.4850.890D0.728 1.333E 1.091 2.000F 1.636 3.000G 2.454 4.500H 3.682 6.751Min.Max.E0.91 1.67F 1.37 2.51G 2.05 3.76H 3.08 5.64I 4.628.64J 6.9312.70K10.3919.04Contrast EnhancementFor information on contrast enhancement, please see Application Note 1015.Soldering/CleaningFor information on soldering LEDs, please refer to Application Note 1029.Electrical/OpticalFor more information onelectrical/optical characteristics,please see Application Note 1005.Color CategoriesNote:All categories are established for classification of products. Products may not be available in all categories. Please contact your Agilent representatives for further clarification/information.HDSP-A5xx IV Bin Category Min.Max.H 0.86 1.58I 1.29 2.37J 1.94 3.55K 2.90 5.33L 4.378.01Intensity Bin Limits (mcd), continued GreenHDSP-F5xx/G5xx IV Bin Category Min.Max.H 1.54 2.82I 2.31 4.23J 3.46 6.34K 5.189.50L 7.7814.26HDSP-H5xx/K5xx IV Bin Category Min.Max.E 0.91 1.67F 1.37 2.51G 2.05 3.76H 3.08 5.64I 4.618.46/semiconductors For product information and a complete list of distributors, please go to our web site.For technical assistance call:Americas/Canada: +1 (800) 235-0312 or (916) 788-6763Europe: +49 (0) 6441 92460China: 10800 650 0017Hong Kong: (+65) 6756 2394India, Australia, New Zealand: (+65) 6755 1939 Japan: (+81 3) 3335-8152 (Domestic/Interna-tional), or 0120-61-1280 (Domestic Only) Korea: (+65) 6755 1989Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843Data subject to change.Copyright © 2004 Agilent Technologies, Inc. Obsoletes 5988-1742ENJuly 17, 20045988-4433EN。

BCYE琼脂配套试剂安全技术说明书

化学品安全技术说明书第一部分化学品及企业标识产品中文名称：BCYE 琼脂配套试剂产品英文名称：Additives For BCYE Agar 产品编号：SR0600企业名称：广东环凯微生物科技有限公司地址：广东省广州市黄埔区广州开发区科学城神舟路788号邮编：510663公司网址电子邮件地址：*********************传真号码：************销售热线：************-8602技术热线：************-8877/8876推荐用途和限制用途：生化研究/分析第三部分成分/组成信息第二部分危险性概述危险性类别：有刺激性侵入途径：皮肤接触或眼睛接触或吸入或摄入健康危害：本品仅用于生化研究/分析，正确使用对人体无害。

如不慎接触或吸入或摄入，对皮肤或眼睛或鼻粘膜或上呼吸道等有毒性作用环境危害本品仅用于生化研究/分析，正确使用和废物处理对环境无害燃爆危险：无燃爆危害混合物化学品成分：参考使用说明第四部分急救措施一般信息：无特殊的措施要求皮肤接触：立即用清水彻底清洗眼睛接触：立即提起眼睑，用大量流动清水冲洗15min。

如不适就医吸入：如果吸入，将人员移动到新鲜空气处，如果没有呼吸，进行人工呼吸操作，并联系医生食入：如误食，用水冲洗口腔，如不适就医就医信息：出示产品使用说明或者此SDS第五部分消防措施危险特性：不助燃有害燃烧产物：一氧化碳，二氧化碳，氮的氧化物灭火方法及灭火剂：选用适合周围火源的灭火器。

水，泡沫，二氧化碳，沙土灭火注意事项：防止气体吸入第六部分泄露应急处理个人防护：穿个人实验服，佩戴手套和口罩，避免吸入干粉环境保护措施：用湿布和地拖擦拭干净清洁/收集措施：保持干燥。

迅速清洗弄脏的区域第七部分操作处置与储存安全操作注意事项：应提供通风设备储存注意事项：贮存于2-8℃处第八部分接触控制/个人防护职业接触限值没有已知的国家规定的暴露极限工程控制：提供安全淋浴和洗眼设备个人保护措施呼吸系统防护：佩戴口罩眼睛防护：佩戴安全眼镜身体防护：穿实验室服手防护：戴防化学品手套其他防护：常规的工业卫生操作，工作后及时清洗双手第九部分理化特性外观：粉末pH值：无数据资料颜色：白色气味：特征性熔点：无数据资料沸点：无数据资料燃点：无数据资料闪点：无数据资料爆炸限度下限：无数据资料上限：无数据资料热分解：无数据资料溶解性：易溶于水第十部分稳定性和反应活性稳定性：在适宜条件下贮存稳定避免接触条件：避免接触强氧化性物质禁忌物：无数据资料危险分解产物：如果根据产品使用说明操作无分解聚合危害：无数据资料第十一部分毒理学资料急性毒性：无数据资料皮肤刺激或腐蚀：无数据资料眼睛刺激或腐蚀：无数据资料呼吸或皮肤过敏：无数据资料生殖细胞突变性：无数据资料致癌性：无数据资料生殖毒性：无数据资料特异性靶器官系统毒性-一次性接触：无数据资料特异性靶器官系统毒性-反复接触无数据资料吸入危害可能引起呼吸道刺激第十二部分生态学资料生态毒性：无数据资料持久性和降解性：无数据资料生物蓄积潜力：无数据资料土壤中的迁移性：无数据资料其它环境危害：无数据资料第十三部分废弃处理产品废弃方法：根据当地政府相关法规处理包装推荐：根据当地政府相关法规规定丢弃或回收推荐清洁试剂：水，如需可以使用清洁试剂第十四部分运输信息联合国危险货物编号（UN号）：无联合国运输名称：非危险货物运输危险性分类别：无包装类别：包装标志：包装方式：海洋污染物（是/否）：无无玻璃瓶，纸盒否运输注意事项请根据化学品性质选择合适的运输工具及相应的运输储存条件。

Engineered O-Rings Catalog ORD 5710 美国Parker O-Rin

Engineered O-Rings Catalog ORD 5710 USASimple solutionsfor complex sealing problemsIn the O-Ring Division’s monitoring each step of the process Finite element analysisElement Analysistion process and ensures theselection of the right materialand geometry for a customer’sapplication. As an addedbenefit, FEAused to predict service life.a simple interfacespecific glands and seals. Itversions of these books, availableas ORD 5703 (US) and 5705(Europe), provide engineersfor static and dynamic seals,with world productionamounting tobillions per year.In 1937,Niels A. Christensen, aDanish emigrant to the USA,was awarded a patent for thisring with the perfectgeometricalshape.In 1949,Parker O-ring materialsled to the aeronautical specifica-tion MIL-P-5515 B and to the dimensionalstandards MS 29512 and 513, which werebased on Parker O-rings. Since then, theO-ring has become a vital sealingelement in all kinds of fluidpower equipment.advice from Parker sealing experts isnever far away.Parker O-Ring division’s manufacturing facilities span 4 continents and 9countries. Some of these The division’s North American headquarters, located in Lexington KY , isApplicationsTransportation•Brakes/ABS•Cooling/air conditioning •Fuel and diesel injection, spark plugs•Quick connects, couplings, gear units•Shock absorbers •Steering systems•Transmissions and radiator sealsAerospace•Aircraft engines, wheels and brakes•Control and actuation systems•Fuel systems•Space shuttle launch vehiclesMedical•Dyalizers•Syringes, infusions•USP Class VI and FDA “White Listed” formulations are availableSemiconductor Processing•For wet, dry and thermal processes•Parker UHP Processing:Parker uses totally enclosed and dedicated manufacturing areas for compounding,preparation, molding, cleaning and final packaging of o-rings in critical compounds for semiconductor processing applicationsFluid Power•Accumulators •Cylinders, valves •Filters •Fittings •Pumps•Rotary actuatorsConsumer Products•Appliances•Compounds meeting the requirements/recommen-dations: FDA, NSF, WRC,DVGW, BGA, KTW •Heating/plumbing •Sanitary equipmentChemical Processing Industry (CPI)•Equipment and components requiring extremely high chemical inertness attemperatures up to +320°CEnergy/Oil Field•Drilling•Exploration •Production •TransportationParker O-rings are used in many applications and industries, including:1-800-C-Parker Parker O-Ring Division Worldwide LocationsNorth AmericaUSAParker Hannifin CorporationO-Ring Division2360 Palumbo Drive Lexington, KY 40509 Phone: (859) 269-2351Fax: (859) 335-5128 Parker Hannifin CorporationO-Ring Division104 Hartmann Drive Lebanon, TN 37087Phone: (615) 444-0191Fax: (615) 449-7312 Parker Hannifin CorporationO-Ring Division109 Industrial Park Drive Livingston, TN 38570 CanadaParker Hannifin CorporationO-Ring Division255 Hughes RoadOrillia, Ontario L3V 2M3 Phone: (705) 325-2391Fax: (705) 325-5721 MexicoParker Hannifin CorporationO-Ring DivisionPSDM Business Unit Diagonal Lorenzo de la Garza #13 Ciudad IndustrialH. Matamoros, Tam. 87490 Parker Hannifin CorporationO-Ring DivisionBRCO Business UnitCalle Sexta Y Vizcaya #95 Col. EuzkadiH. Matamoros, Tam. 87370 EuropeAustriaSee GermanyBelgiumParker Hannifin SA NVParc Industriel Sud, Zone II 15, Rue du Bosquet1400 NivellesPhone:+(32) 67-28 09 00 Fax:+(32) 67-28 09 99 Czech RepublicParker Hannifin s.r.o. Podebradská 100528912 SadskáPhone: +(420) 325-55 5111 Fax: +(420) 325-55 5112 DenmarkPolar Seals A/S Bjergvangen 23060 EspergærdePhone: +(45) 49 12 17 00 Fax: +(45) 49 12 17 01FinlandParker Hannifin OyYlastontie 16FIN-01510 VantaaPhone: +(358) 9-47 67 31Fax: +(358) 9-47 67 32 00FranceParker Hannifin RakZ.l. du Mont-BlancB.P. 482, Ville-la-Grand74108 Annemasse-CédexPhone: +(33) 4-50 87 80 80Fax: +(33) 4-50 87 80 76GermanyParker Hannifin GmbHO-Ring DivisionStuifenstr. 55D-74385 PleidelsheimPhone:+(49) 71 44-206-0Fax: +(49) 71 44-2 37 49HungaryParker Hannifin CorporationBudapest Representation OfficeVezer u. 156-1581148 BudapestPhone: +(36) 1-2 52 81 37Fax: +(36) 1-2 52 81 29IrelandSee United KingdomItalyParker Seals S.p.A.Via Marzaghette 2I-25030, Adro (BS)Phone: +(39) 030 754 811Fax: +(39) 030 745 8210Parker Hannifin S.p.A.Via Priv. Archimede, 120094 Corsico (Mi)Phone: +(39) 02-4 51 92-1Fax: +(39) 02-4 47 93 40NetherlandsParker Hannifin B.V.Edisonstraat 1P.O. Box 3407570 AH OldenzaalPhone: +(31) 541-58 50 00Fax: +(31) 541-58 54 59NorwayParker Hannifin A/SBerghagenP.O. Box 3008N-1402 SkiPhone: +(47) 64 91 10 00Fax: +(47) 64 91 10 90PolandParker Hannifin Sp. z.o.o.ul. Parowcowa 8B02-445 WarsawPhone: +(48) 22-8 63 49 42/43Fax: +(48) 22-8 63 49 44RussiaParker Hannifin CorporationKomsomolsky Prospect 42Office 407119827 GSP Moscow G-48Phone: +(7) 095-234 0054Fax: +(7) 095-242 0907Slovakiasee Czech RepublicSwedenParker Hannifin Sweden ABBox 831416308 SpangaPhone: +(46) 8-7 60 29 60Fax: +(46) 8-7 61 81 70SwitzerlandSee GermanySpainParker Hannifin Espana S.A.Paseo Cordellas, 5708290 Cerdanyola-del-Valles(Barcelona)Phone: +(34) 93-6 91 50 62Fax: +(34) 93-6 91 46 19United KingdomParker Hannifin plcSeal GroupParkway, Globe ParkMarlow, Bucks SL7 1YBPhone: +(44) 16 28-40 40 88Fax: +(44) 16 28-40 40 89Asia PacificAustraliaParker Hannifin Australia Pty. Ltd.9 Carrington Road2154 (NSW) Castle HillPhone: +(61) 2-96 34 77 77Fax: +(61) 2-98 42 51 11ChinaParker HannifinFluid Power Systems(Shanghai) Co., Ltd.280 Yun Qiao RoadJian Qiao Export Processing ZoneShanghai 201206Phone: +(86) 21-5031 2525Fax: +(86) 21-5834 3714Parker Asun Sealing CompanyNo. 26 Tian Bao RoadTian Bao Industrial ZoneDong Guan CityGuang Dong, P.R.O.C.Hong KongParker Hannifin Hong Kong Ltd.8/F Kin Yip Plaza9 Cheung Y ee StreetCheung Sha Wan, KowloonPhone: +(852) 24 28 80 08Fax: +(852) 24 80 42 56JapanParker Hannifin Japan Ltd.Osaka Sales OfficeNo. 2 Tani Bldg.1-4-25, Nishi-Miyahara,Yodogawa-KuPhone: +(81) 6-48 07-32 88Fax: +(81) 6-48 07-32 99KoreaParker Hannifin Korea Ltd.902 Dae Heung Bldg.648-23 Yeaksam-dongKangnam-Ku, Seoul 135-080Phone: +(82) 2-5 61 04 14Fax: +(82) 2-5 56 81 87SingaporeParker Hannifin Singapore Pte., Ltd.No. 11 Fourth Chin Bee RoadJurong Town 61 9702Phone: +(65) 261 5233Fax: +(65) 265 5125TaiwanParker Hannifin Taiwan, Ltd.8F-1, No 102 Sung Lung RoadTaipeiPhone: +(886) 2 8787 3780Fax: +(886) 2 8787 3782AfricaParker Hannifin Africa Pty. Ltd.Parker Place10 Berne AvenueAeroportKempton Park, South AfricaPhone: +(27) 11-3 92 72 80Fax: +(27) 11-3 92 72 13Latin AmericaArgentinaParker Hannifin Argentina SAICStephenson 27111667 Tortuguitas - Malvinas Arg.Buenos AiresPhone: +(54) 1-1 47 52-41 29Fax: +(54) 1-1 47 52-37 04BrazilParker Hannifin do BrasilIndustria e Comercia Ltda.Via Anhanguera, Km 25,305275 Sao Paulo / SPPhone: +(55) 11-39 17-10 99Fax: +(55) 11-39 17-08 17Continental HeadquartersManufacturing plants1/2-2.5M-CE。

LORD HPC-5B产品安全数据表说明书

USA SAFETY DATA SHEET1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct name:LORD HPC-5BProduct Use/Class: CoatingLORD Corporation111 LORD DriveCary, NC 27511-7923 USATelephone: 814 868-3180Non-Transportation Emergency: 814 763-2345Chemtrec 24 Hr Transportation Emergency No.800 424-9300 (Outside Continental U.S. 703 527-3887)EFFECTIVE DATE: 04/12/20212. HAZARDS IDENTIFICATIONGHS CLASSIFICATION:Flammable liquids Category 2Acute toxicity Inhalation - Vapours Category 3Acute toxicity Inhalation - Dust and Mist Category 3Skin corrosion/irritation Category 2Serious eye damage/eye irritation Category 2ASkin sensitization Category 1Carcinogenicity Category 2Specific target organ systemic toxicity (single exposure) Category 1 Central nervous system, LiverSpecific target organ systemic toxicity (single exposure) Category 3Specific target organ systemic toxicity (repeated exposure) Category 1 Central nervous systemSpecific target organ systemic toxicity (repeated exposure) Category 2 Bladder, Respiratory systemGHS LABEL ELEMENTS:Symbol(s)Signal WordD ANGERHazard StatementsHighly flammable liquid and vapor.Toxic if inhaled.Causes skin irritation.Causes serious eye irritation.May cause an allergic skin reaction.Suspected of causing cancer.Causes damage to organs.(Central nervous system, Liver)May cause respiratory irritation.May cause drowsiness or dizziness.Causes damage to organs through prolonged or repeated exposure.(Central nervous system)May cause damage to organs through prolonged or repeated exposure.(Bladder, Respiratory system) Precautionary StatementsPreventionKeep away from heat/sparks/open flames/hot surfaces. - No smoking.Ground/Bond container and receiving equipment.300000002423Use explosion-proof electrical/ventilating/lighting equipment.Use only non-sparking tools.Take precautionary measures against static discharge.Obtain special instructions before use.Do not handle until all safety precautions have been read and understood.Wear protective gloves/protective clothing/eye protection/face protection.Use personal protective equipment as required.Do not breathe dust/fume/gas/mist/vapors/spray.Wash thoroughly after handling.Do not eat, drink or smoke when using this product.Use only outdoors or in a well-ventilated area.Contaminated work clothing should not be allowed out of the workplace.ResponseIn case of fire: refer to section 5 of SDS for extinguishing media.Call a POISON CENTER or doctor/physician.Specific treatment (see supplemental first aid instructions on this label).IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing.IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.If skin irritation or rash occurs: Get medical advice/attention.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.Continue rinsing.StorageStore in a well-ventilated place. Keep cool.Store in a well-ventilated place. Keep container tightly closed.Store locked up.Disposal:Dispose of contents/container in accordance with waste/disposal laws and regulations of your country or particular locality.Other Hazards:This product contains component(s) which have the following warnings; however based on the GHS classification criteria of your country or locale, the product mixture may be outside the respective category(s).Acute: Vapor harmful; may affect the brain or nervous system causing dizziness, headache or nausea. Possibleirritation of the respiratory system can occur causing a variety of symptoms such as dryness of the throat, tightness of the chest, and shortness of breath. May cause central nervous system depression characterized by the followingprogressive steps: headache, dizziness, staggering gait, confusion, unconsciousness or coma. The silane monomer in this product may decompose to become methanol. For methanol, the OSHA PEL is 200 ppm, and the ACGIH STEL is 250 ppm (Skin). Silane monomer 1 in this product may decompose to become ethanol. For ethanol, the OSHA PEL is 1000 ppm, and the ACGIH TLV-TWA is 1000 ppm. Dermal absorption possible.May be harmful if swallowed.Ingestion is not an expected route of entry in industrial or commercial uses.Chronic: May cause kidney damage. IARC has designated Methyl isobutyl ketone to be in Group 2B - possibly carcinogenic to humans. IARC has designated carbon black as Group 2B - inadequate evidence for carcinogenicity in humans, but sufficient evidence in experimental animals. In 2006 IARC reaffirmed its 1995 finding that there is"inadequate evidence" from human health studies to assess whether carbon black causes cancer in humans. Further, epidemiological evidence from well-conducted investigations has shown no causative link between carbon black exposure and the risk of malignant or non-malignant respiratory disease in humans.withheld.FIRST AID - EYE CONTACT: Flush eyes immediately with large amount of water for at least 15 minutes holding eyelids open while flushing. Get prompt medical attention.FIRST AID - SKIN CONTACT: Flush contaminated skin with large amounts of water while removing contaminated clothing. Wash affected skin areas with soap and water. Get medical attention if symptoms occur.FIRST AID - INHALATION: Move person to fresh air. Restore and support continued breathing. If breathing is difficult, give oxygen. Get immediate medical attention.FIRST AID - INGESTION: If swallowed, do not induce vomiting. Call a physician or poison control center immediately for further instructions. Never give anything by mouth if victim is rapidly losing consciousness, unconscious or convulsing.SUITABLE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water FogUNSUITABLE EXTINGUISHING MEDIA: Not determined for this product.SPECIFIC HAZARDS POSSIBLY ARISING FROM THE CHEMICAL: Flammable liquid and vapor. Keep containers tightly closed. Isolate from heat, electrical equipment, sparks, open flame, and other sources of ignition. Closed containers may rupture when exposed to extreme heat. Use water spray to keep fire exposed containers cool. During a fire, irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion.SPECIAL PROTECTIVE EQUIPMENT AND PRECAUTIONS FOR FIRE-FIGHTERS: Wear full firefighting protective clothing, including self-contained breathing apparatus (SCBA). Water spray may be ineffective. If water is used, fog nozzles are preferable.PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES: Remove all sources of ignition (flame, hot surfaces, and electrical, static or frictional sparks). Avoid contact. Avoid breathing vapors. Use self-contained breathing equipment.ENVIRONMENTAL PRECAUTIONS: Do not contaminate bodies of water, waterways, or ditches, with chemical or used container.METHODS AND MATERIALS FOR CONTAINMENT AND CLEANUP: Keep non-essential personnel a safe distance away from the spill area. Notify appropriate authorities if necessary. Avoid contact. Before attempting cleanup, refer to hazard caution information in other sections of the SDS form. Contain and remove with inert absorbent material.HANDLING: Keep closure tight and container upright to prevent leakage. Ground and bond containers when transferring material. Avoid skin and eye contact. Wash thoroughly after handling. Avoid breathing of vapor or spray mists. Do not handle until all safety precautions have been read and understood. Empty containers should not be re-used. Use with adequate ventilation. Because empty containers may retain product residue and flammable vapors, keep away from heat, sparks and flame; do not cut, puncture or weld on or near the empty container. Do not smoke where this product is used or stored.STORAGE: Do not store or use near heat, sparks, or open flame. Store only in well-ventilated areas. Do not puncture, drag, or slide container. Keep container closed when not in use. Refer to OSHA 29CFR Part 1910.106 "Flammable and Combustible Liquids" for specific storage requirements.INCOMPATIBILITY: Strong acids, bases, and strong oxidizers.Engineering controls: Sufficient ventilation in pattern and volume should be provided in order to maintain air contaminant levels below recommended exposure limits. Caution: Solvent vapors are heavier than air and collect in lower levels of the work area. Sufficient ventilation (using explosion-proof equipment) should be provided to prevent flammable vapor/air mixtures from accumulating.PERSONAL PROTECTION MEASURES/EQUIPMENT:RESPIRATORY PROTECTION: Use a NIOSH approved chemical/mechanical filter respirator designed toremove a combination of particulates and organic vapor if occupational limits are exceeded. For emergencysituations, confined space use, or other conditions where exposure limits may be greatly exceeded, use an approved air-supplied respirator. For respirator use observe OSHA regulations (29CFR 1910.134) or use in accordance with applicable laws and regulations of your country or particular locality.SKIN PROTECTION: Use neoprene, nitrile, or rubber gloves to prevent skin contact.EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles where splashing may occur.OTHER PROTECTIVE EQUIPMENT: Use disposable or impervious clothing if work clothing contamination is likely. Remove and wash contaminated clothing before reuse.HYGIENIC PRACTICES: Wash hands before eating, smoking, or using toilet facility. Do not smoke in anychemical handling or storage area. Food or beverages should not be consumed anywhere this product is handled or stored. Wash thoroughly after handling.Typical values, not to be used for specification purposes.ODOR: Solvent VAPOR PRESSURE: N.D.APPEARANCE: Black VAPOR DENSITY: Heavier than Air PHYSICAL STATE: Liquid LOWER EXPLOSIVE LIMIT: 0.8 %(V)UPPER EXPLOSIVE LIMIT: 7.5 %(V)FLASH POINT: 60 °F, 15 °C SetaflashClosed CupBOILING RANGE: 114 - 169 °C EVAPORATION RATE: Faster than n-butyl-acetate.AUTOIGNITION TEMPERATURE:N.D.DENSITY: 0.83 g/cm3 (6.88 lb/gal) DECOMPOSITION TEMPERATURE:N.D. VISCOSITY, DYNAMIC: ≥20 mPa.s @ 25 °C ODOR THRESHOLD: N.D.VISCOSITY, KINEMATIC: ≥24 mm2/s @ 25 °CSOLUBILITY IN H2O: Partially Soluble VOLATILE BY WEIGHT: 91.80 %pH: N.A.VOLATILE BY VOLUME: 93.43 %FREEZE POINT: N.D. VOC CALCULATED: 6.32 lb/gal, 757 g/lN.D.COEFFICIENT OF WATER/OILDISTRIBUTION:LEGEND: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not DeterminedHAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur under normal conditions. STABILITY: Product is stable under normal storage conditions.CONDITIONS TO AVOID: High temperatures. Sources of ignition.INCOMPATIBILITY: Strong acids, bases, and strong oxidizers.HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide, carbon dioxide, Oxides of nitrogen, Oxides of siliconEXPOSURE PATH: Refer to section 2 of this SDS.SYMPTOMS:Refer to section 2 of this SDS.TOXICITY MEASURES:Germ cell mutagenicity: No classification proposedCarcinogenicity: Category 2 - Suspected of causing cancer.Components contributing to classification: Methyl isobutyl ketone.Reproductive toxicity: No classification proposedPERSISTENCE AND DEGRADABILITY:Not determined for this product.BIOACCUMULATIVE: Not determined for this product.MOBILITY IN SOIL: Not determined for this product.OTHER ADVERSE EFFECTS: Not determined for this product.DISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and local environmental control regulations. If waste is determined to be hazardous, use licensed hazardous waste transporter and disposal facility.US DOT RoadProper Shipping Name: PaintHazard Class: 3SECONDARY HAZARD: NoneUN/NA Number: 1263Packing Group: IIEmergency Response Guide Number: 128IATA CargoPROPER SHIPPING NAME: PaintHazard Class: 3HAZARD CLASS: NoneUN NUMBER: 1263PACKING GROUP: IIEMS: 3LIMDGPROPER SHIPPING NAME: PaintHazard Class: 3HAZARD CLASS: NoneUN NUMBER: 1263PACKING GROUP: IIEMS: F-EThe listed transportation classification applies to non-bulk shipments. It does not address regulatory variations due to changes in package size, mode of shipment or other regulatory descriptors. For the most accurate shipping information, refer to your transportation/compliance department.U.S. FEDERAL REGULATIONS: AS FOLLOWS:SARA SECTION 313This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372.:Chemical Name CAS Number Weight % Less ThanMethyl isobutyl ketone108-10-185.0%TOXIC SUBSTANCES CONTROL ACT:INVENTORY STATUSThe chemical substances in this product are on the active TSCA Section 8 Inventory or exempt.EXPORT NOTIFICATIONThis product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if exported from the United States:NoneUnder HazCom 2012 it is optional to continue using the HMIS rating system. It is important to ensure employees have been trained to recognize the different numeric ratings associated with the HazCom 2012 and HMIS schemes.HMIS RATINGS - HEALTH: 3* FLAMMABILITY: 3 PHYSICAL HAZARD: 0* - Indicates a chronic hazard; see Section 2Revision: Company LogoEffective Date: 04/12/2021The information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred by use of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and regulations.。

理化特性表第5类

目录5.1类氧化剂过氧化氢的理化性质及危险特性（表-） (1)过氧化钠的理化性质及危险特性（表-） (2)高氯酸[含酸50%～72%]的理化性质和危险特性(表-) (3)高氯酸钠的理化性质和危险特性(表-) (4)氯酸钠的理化性质和危险特性(表-) (5)氯酸钾的理化性质和危险特性(表-) (6)亚氯酸钠的理化性质及危险特性（表-） (7)高锰酸钠的理化性质及危险特性（表-） (8)高锰酸钾的理化性质及危险特性（表-） (9)硝酸钠的理化性质及危险特性（表-） (10)硝酸钾的理化性质和危险特性（表-） (11)硝酸钙的理化性质和危险特性(表-) (12)硝酸锶的理化性质和危险特性(表-) (13)硝酸钡的理化性质及危险特性（表-） (14)硝酸锌的理化性质和危险特性(表-) (15)硝酸银的理化性质及危险特性（表-） (16)硝酸铅的理化性质及危险特性（表-） (17)亚硝酸钾的理化性质及危险特性（表-） (18)过（二）碳酸钠的理化性质及危险特性(表-) (19)过硫酸铵的理化性质及危险特性（表-） (20)过硫酸钾的理化性质及危险特性(表-) (22)过硼酸钠的理化性质及危险特性（表-） (23)漂白粉的理化性质及危险特性(表-) (24)溴酸钠的理化性质和危险特性(表-) (25)溴酸钾的理化性质和危险特性(表-) (28)高碘酸的理化性质和危险特性(表-) (29)高碘酸钠的理化性质和危险特性(表-) (30)高碘酸钾的理化性质和危险特性(表-) (31)碘酸钠的理化性质和危险特性(表-) (32)碘酸钾的理化性质和危险特性(表-) (33)三氧化铬［无水］的理化性质及危险特性(表-) (34)重铬酸钾的理化性质及危险特性（表-） (35)硝酸镁的理化性质和危险特性(表-) (37)硝酸铁的理化性质和危险特性(表-) (38)硝酸镍的理化性质和危险特性(表-) (39)硝酸钴的理化性质及危险特性（表-） (40)硝酸铝的理化性质和危险特性(表-) (41)硝酸锰的理化性质和危险特性(表-) (42)硝酸铜的理化性质和危险特性(表-) (43)硝酸铋的理化性质和危险特性(表-) (44)硝酸镧的理化性质和危险特性(表-) (45)硝酸铈铵的理化性质和危险特性(表-) (47)亚硝酸钠的理化性质及危险特性(表-) (48)氧化银的理化性质及危险特性（表-） (49)5.2类有机过氧化物过氧化二异丙苯[含量＞42%,带有惰性固体]的理化性质和危险特性(表-)50 过氧化(二)苯甲酰[77%＜含量＜95%,含水]的理化性质和危险特性(表-) 51 过氧化乙酸的理化性质及危险特性（表-） (52)高氯酸[含酸50%～72%]的理化性质和危险特性(表-)高氯酸钠的理化性质和危险特性(表-)氯酸钠的理化性质和危险特性(表-)亚氯酸钠的理化性质及危险特性（表-）硝酸钠的理化性质及危险特性（表-）过硼酸钠的理化性质及危险特性（表-）溴酸钠的理化性质和危险特性(表-)次氯酸钙[含有效氯＞39%]的理化性质及危险特性(表4-7)硝酸铵[含可燃物≤0.2%]的理化性质及危险特性(表4-7)重铬酸钾的理化性质及危险特性（表-）硝酸镁的理化性质和危险特性(表-)硝酸钴的理化性质及危险特性（表-）。

5082-5703-EF000中文资料

14.2 mm (0.56 inch)Seven Segment Displays Technical DataFeatures• Industry Standard Size • Industry Standard Pinout 15.24 mm (0.6 in.) DIP Leads on 2.54 mm (0.1 in.) Centers • Choice of ColorsAlGaAs Red, High Efficiency Red, Yellow, Green, Orange • Excellent Appearance Evenly Lighted Segments Mitered Corners on Segments Gray Package Gives Optimum Contrast±50° Viewing Angle • Design FlexibilityCommon Anode or Common CathodeSingle and Dual Digits Right Hand Decimal Point ±1. Overflow Character• Categorized for Luminous IntensityYellow and Green Categorized for ColorUse of Like Categories Yields a Uniform Display • High Light Output • High Peak Current• Excellent for Long Digit String Multiplexing • Intensity and Color Selection OptionSee Intensity and ColorSelected Displays Data Sheet • Sunlight Viewable AlGaAsDescriptionThe 14.2 mm (0.56 inch) LED seven segment displays aredesigned for viewing distances upto 7 metres (23 feet). Thesedevices use an industry standard size package and pinout. Both the numeric and ±1 overflow devices feature a right hand decimalpoint. All devices are available as either common anode or common cathode.Orange AlGaAs Red HERYellowGreen Package HDSP-HDSP-[1]HDSP-[1]HDSP-HDSP- DescriptionDrawingH401H151550157015601Common Anode Right Hand Decimal A H403H153550357035603Common Cathode Right Hand Decimal B H157550757075607Common Anode ±1. Overflow C H158550857085608Common Cathode ±1. OverflowD K401552157215621Two Digit Common Anode Right Hand DecimalE K403552357235623Two Digit Common Cathode Right Hand DecimalFDevicesNote:1. These displays are recommended for high ambient light operation. Please refer to the HDSP-H10X/K12X AlGaAs and HDSP-555X HER data sheet for low current operation.HDSP-K40x Series HDSP-550x Series HDSP-552x Series HDSP-560x Series HDSP-562x Series HDSP-570x Series HDSP-572x Series HDSP-H15x Series HDSP-H40x SeriesThese displays are ideal for most applications. Pin for pin equivalent displays are alsoavailable in a low current design.The low current displays are idealfor portable applications. For additional information see the Low Current Seven Segment Displays data sheet.Part Numbering SystemNotes:1. For codes not listed in the figure above, please refer to the respective datasheet or contact your nearest Agilent representative for details.2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically restricted to 1bin per tube (exceptions may apply). Please refer to respective datasheet for specific bin limit information.5082 -X X X X-X X X X X HDSP-X X X X-X X X X XMechanical Options [1]00: No Mechanical Option Color Bin Options [1,2]0: No Color Bin LimitationMaximum Intensity Bin [1,2]0: No Maximum Intensity Bin Limitation Minimum Intensity Bin [1,2]0: No Minimum Intensity Bin Limitation Device Configuration/Color [1]1: Common Anode 3: Common CathodeDevice Specific Configuration [1]Refer to Respective DatasheetPackage [1]H: 14.2 mm (0.56 inch) Single Digit Seven Segment DisplayFUNCTIONPIN AB CDEF1CATHODE e ANODE e CATHODE c ANODE cE CATHODE NO. 1 E ANODE NO. 12CATHODE d ANODE d ANODE c, d CATHODE c, d D CATHODE NO. 1 D ANODE NO. 13ANODE [3]CATHODE [4]CATHODE b ANODE bC CATHODE NO. 1 C ANODE NO. 14CATHODE c ANODE c ANODE a, b, DP CATHODE a, b, DP DP CATHODE NO. 1DP ANODE NO. 15CATHODE DP ANODE DP CATHOPDE DP ANODE DE E CATHODE NO. 1 E ANODE NO. 26CATHODE b ANODE b CATHODE a ANODE aD CATHODE NO. 2 D ANODE NO. 27CATHODE a ANODE a ANODE a, b, DP CATHODE a, b, DP G CATHODE NO. 2G ANODE NO. 28ANODE [3]CATHODE [4]ANODE c, d CATHODE c, d C CATHODE NO. 2 C ANODE NO. 29CATHODE f ANODE f CATHODE d ANODE d DP CATHODE NO. 2DP ANODE NO. 210CATHODE g ANODE g NO PINNO PINB CATHODE NO. 2 B ANODE NO. 211 A CATHODE NO. 2 A ANODE NO. 212 F CATHODE NO. 2 F ANODE NO. 213DIGIT NO. 2 ANODE DIGIT NO. 2 CATHODE 14DIGIT NO. 1 ANODE DIGIT NO. 1 CATHODE 15 B CATHODE NO. 1 B ANODE NO. 116 A CATHODE NO. 1 A ANODE NO. 117G CATHODE NO. 1G ANODE NO. 118F CATHODE NO. 1 F ANODE NO. 1NOTES:1. ALL DIMENSIONS IN MILLIMETRES (INCHES).2. ALL UNTOLERANCED DIMENSIONS ARE FOR REFERENCE ONLY.3. REDUNDANT ANODES.4. REDUNDANT CATHODES.5. FOR HDSP-5600/-5700 SERIES PRODUCT ONLY.Package DimensionsInternal Circuit DiagramNotes:1. See Figure 2 to establish pulsed conditions.2. Derate above 46°C at 0.54 mA/°C.3. See Figure 7 to establish pulsed conditions.4. Derate above 53°C at 0.45 mA/°C.5. See Figure 8 to establish pulsed conditions.HER/Orange HDSP-5500AlGaAs Red HDSP-H40x Yellow Green HDSP-H150HDSP-K40x HDSP-5700HDSP-5600 Description SeriesSeriesSeriesSeriesUnits Average Power per Segment or DP 9610580105mW Peak Forward Current per 160[1]90[3]60[5]90[7]mA Segment or DPDC Forward Current per Segment or DP 40[2]30[4]20[6]3018]mA Operating Temperature Range -20 to +100[9]-40 to +100°C Storage Temperature Range -55 to +100°C Reverse Voltage per Segment or DP 3.0V Lead Solder Temperature for 3 Seconds 260°C(1.60 mm [0.063 in.] below seating plane)Absolute Maximum Ratings6. Derate above 81°C at 0.52 mA/°C.7. See Figure 9 to establish pulsed conditions.8. Derate above 39°C at 0.37 mA/°C.9. For operation below -20°C, contact your local Agilent components sales office or an authorized distributor.Electrical/Optical Characteristics at T A = 25°CAlGaAs RedDeviceSeriesHDSP- Parameter Symbol Min.Typ.Max.Units Test Conditions Luminous Intensity/Segment[1,2,5]I V9.116.0mcd I F = 20 mA(Digit Average)1.8I F = 20 mAForward Voltage/Segment or DP V F V2.03.0I F = 100 mAH15XPeak WavelengthλPEAK645nmDominant Wavelength[3]λd637nmReverse Voltage/Segment or DP[4]V R 3.015V I R = 100 µATemperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DPThermal Resistance LED Junction-RθJ-Pin400°C/W/to-Pin SegHigh Efficiency RedDeviceSeriesHDSP- Parameter Symbol Min.Typ.Max.Units Test Conditions9002800I F = 10 mA Luminous Intensity/Segment[1,2,6]I Vµcd(Digit Average)3700I F = 60 mA Peak:1 of 6 dfForward Voltage/Segment or DP V F 2.1 2.5V I F = 20 mA 55XXPeak WavelengthλPEAK635nmDominant Wavelength[3]λd626nmReverse Voltage/Segment or DP[4]V R 3.030V I R = 100 µATemperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DPThermal Resistance LED Junction-RθJ-Pin345°C/W/to-Pin SegYellowDeviceSeriesHDSP- Parameter Symbol Min.Typ.Max.Units Test Conditions6001800I F = 10 mA Luminous Intensity/Segment[1,2]I Vµcd(Digit Average)2750I F = 60 mA Peak:1 of 6 dfForward Voltage/Segment or DP V F 2.1 2.5V I F = 20 mA 57XXPeak WavelengthλPEAK583nmDominant Wavelength[3,7]λd581.5586592.5nmReverse Voltage/Segment or DP[4]V R 3.040V I R = 100 µATemperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DPThermal Resistance LED Junction-RθJ-Pin345°C/W/to-Pin SegOrangeDeviceSeriesHDSP- Parameter Symbol Min.Typ.Max.Units Test Conditions Luminous Intensity/Segment I V 2.37mcd I F = 10 mA(Segment Average)[1,2]Forward Voltage/Segment or DP V F 2.1 2.5V I F = 20 mAPeak WavelengthλPEAK600nm H40x Dominant Wavelength[3]λd603nm I F = 10 mA K40x Reverse Voltage/Segment or DP[4]V R 3.030V I R = 100 µA Temperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DPThermal Resistance LED Junction-RθJ-Pin345°C/W/to-Pin SegDeviceSeriesHDSP-ParameterSymbol Min.Typ.Max.UnitsTest Conditions 9002500I F = 10 mALuminous Intensity/Segment [1,2]I Vµcd(Digit Average)`3100I F = 60 mA Peak:1 of 6 df Forward Voltage/Segment or DPV F 2.1 2.5V I F = 10 mA56XXPeak Wavelength λPEAK 566nm Dominant Wavelength [3,7]λd 571577nm Reverse Voltage/Segment or DP [4]V R 3.050V I R = 100 µATemperature Coefficient of ∆V F /°C -2mV/°C V F /Segment or DPThermal Resistance LED Junction-R θJ-Pin345°C/W/to-PinSegHigh Performance GreenNotes:1. Device case temperature is 25°C prior to the intensity measurement.2. The digits are categorized for luminous intensity. The intensity category is designated by a letter on the side of the package.3. The dominant wavelength, λd , is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device.4. Typical specification for reference only. Do not exceed absolute maximum ratings.5. For low current operation, the AlGaAs HDSP-H10X series displays are recommended. They are tested at 1 mA dc/segment and are pin for pin compatible with the HDSP-H15X series.6. For low current operation, the HER HDSP-555X series displays are recommended. They are tested at 2 mA dc/segment and are pin for pin compatible with the HDSP-550X series.7. The Yellow (HDSP-5700) and Green (HDSP-5600) displays are categorized for dominant wavelength. The category is designated by a number adjacent to the luminous intensity category letter.AlGaAs RedFigure 3. Maximum Allowable DC Current vs.Ambient Temperature.Figure 4. Forward Current vs.Forward Voltage.HER, Yellow, Green, OrangeFigure 7. Maximum Tolerable Peak Currentvs. Pulse Duration – HER, Orange.I D C M A X . – M A X I M U M D C C U R R E N T P E R S E G M E N T – m AT A – AMBIENT TEMPERATURE – °C 5030102051525354045I F – F O R W A R D C U R R E N T P E R S E G M E N T – m AV F – FORWARD VOLTAGE – VR E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D T O 1 A T 20 m A)I F – FORWARD CURRENT PER SEGMENT – mA204010305152535ηP E A K – N O R M A L IZ E D R E L A T I V E E F F I C I E N C YI PEAK – PEAK FORWARD CURRENTPER SEGMENT – mA4550110120Figure 11. Forward Current vs.Forward Voltage.Figure 9. Maximum Tolerable PeakCurrent vs. Pulse Duration – Green.Figure 10. Maximum Allowable DC Current vs.Ambient Temperature.Figure 12. Relative LuminousIntensity vs. DC Forward Current.Figure 13. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current.Electrical/OpticalFor more information onelectrical/optical characteristics,please see Application Note 1005.Contrast EnhancementFor information on contrastenhancement please see Application Note 1015.Soldering/CleaningCleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from thechlorinated hydrocarbon family(methylene chloride, trichloro–ethylene, carbon tetrachloride,etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts.For information on soldering LEDs please refer to Application Note 1027.I F – F O R W A R D C U R R E N T P E R S E G M E N T – m AV F – FORWARD VOLTAGE – VR E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D A T 10 m A )I F – DC FORWARD CURRENT – mAηV – R E L A T I V E E F F I C I E N C Y (N O R M A L I Z E D T O 1 A T 10 m A P E R S E G ME N T )0.6I PEAK – PEAK FORWARD CURRENTPER SEGMENT – mA902070801001.61.41.31.10.90.860504030100.71.01.21.5HDSP-H15x IV Bin Category Min.Max.K 9.2016.90L 13.8025.30M 20.7038.00N 31.1056.90O 46.6085.40Intensity Bin Limits (mcd)AlGaAs RedHDSP-550x/552x IV Bin Category Min.Max.E 0.91 1.67F 1.37 2.51G 2.05 3.76H 3.08 5.64I 4.628.64J 6.9312.70K 10.3919.04HERHDSP-570x/572xIV Bin Category Min.Max.D 0.61 1.11E 0.91 1.67F 1.37 2.51G 2.05 3.76H 3.08 5.64I 4.628.64J 6.9312.70K 10.3919.04YellowHDSP-560x/562x IV Bin Category Min.Max.E 0.91 1.67F 1.37 2.51G 2.05 3.76H 3.08 5.64I 4.618.46GreenColor CategoriesNote:All categories are established for classification of products. Products may not be available in all categories. Please contact your Agilent representatives for further clarification/information.10HDSP-H40x/K40x IV Bin Category Min.Max.B 0.77 1.17C 0.95 1.45D 1.19 1.82E 1.49 2.27F 1.85 2.89G 2.32 3.54H 2.904.43Orange元器件交易网元器件交易网/semiconductorsFor product information and a complete list ofdistributors, please go to our web site.For technical assistance call:Americas/Canada: +1 (800) 235-0312 or(408) 654-8675Europe: +49 (0) 6441 92460China: 10800 650 0017Hong Kong: (+65) 271 2451India, Australia, New Zealand: (+65) 271 2394Japan: (+81 3) 3335-8152(Domestic/Interna-tional), or 0120-61-1280(Domestic Only)Korea: (+65) 271 2194Malaysia, Singapore: (+65) 271 2054Taiwan: (+65) 271 2654Data subject to change.Copyright © 2002 Agilent Technologies, Inc.Obsoletes 5988-0383ENJanuary 17, 20025988-4273EN。

5082-333G-KH400中文资料

DescriptionThis 7.62 mm (0.3 inch) LED seven-segment display uses industry standard size package and pinout. The device isavailable in either common anodeAgilent HDSP-331x/332E/333x/334x Series 7.62 mm (0.3 inch) General Purpose Seven-Segment DisplayData SheetFeatures•Industry standard size•Industry standard pinout7.62 mm (0.4 inch) character height DIP lead on 2.54 mm •Choice of colorsHigh Efficiency Red (HER), Green,AlGaAs Red, and Yellow •Excellent appearanceEvenly lighted segments gray pack-age gives optimum contrast ± 50° viewing angle •Design flexibilityCommon anode or common cathode Single digitLeft and right hand decimal point•Categorized for luminous intensityGreen and yellow categorized for color Applications•Suitable for indoor use•Not recommended for industrial application, i.e., operating temperature requirementsexceeding +85˚C or below –25˚C [1]•Extreme temperature cycling not recommendedNote:1.For additional details, please contact your local Agilent sales office or an authorized distributor.Devices HERGreenAlGaAs Red Yellow DescriptionPackage Drawing HDSP-331E HDSP-331GHDSP-331AHDSP-331YCommon Anode, Right Hand and A Left Hand DecimalHDSP-332E Common Anode, Right Hand and Left A Hand Decimal without Pin 4, 5 and 12HDSP-333E HDSP-333G HDSP-333A HDSP-333Y Common Cathode, Right Hand B DecimalHDSP-334EHDSP-334GHDSP-334AHDSP-334YCommon Cathode, Right Hand DecimalCor common cathode. The choice of colors includes High Efficiency Red (HER), Green, AlGaAs Red,and Yellow. The gray facedisplays are suitable for indoor use.Part Numbering SystemNotes:1. For codes not listed in the figure above, please refer to the respective datasheet or contact your nearest Agilent representative for details.2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically restricted to 1bin per tube (exceptions may apply). Please refer to respective datasheet for specific bin limit information.5082 -X X X X-X X X X X HDSP-X X X X-X X X X XMechanical Options [1]00: No Mechanical Option Color Bin Options [1,2]0: No Color Bin LimitationMaximum Intensity Bin [1,2]0: No Maximum Intensity Bin Limitation Minimum Intensity Bin [1,2]0: No Minimum Intensity Bin Limitation Device Configuration/Color [1]A: AlGaAs RedE: High Efficiency Red G: Green Y: YellowDevice Specific Configuration [1]Refer to Respective Datasheet Package [1]Refer to Respective Datasheet∅1.1FRONT VIEWTOP END VIEWA F GB C L.DPD E DIMENSIONS IN MILLIMETERS (INCHES)R.DPNOTE: HDSP-332E DOES NOT HAVE PIN 4, 5 AND 12.Package Drawing APackage Drawing B∅1.1FRONT VIEW TOP END VIEWAF G BCDEDIMENSIONS IN MILLIMETERS (INCHES)R.DPPackage Drawing C∅1.1FRONT VIEW TOP END VIEWAF G BCDEDIMENSIONS IN MILLIMETERS (INCHES)R.DP611310872113.14 COMPIN N0.123678910111314CONNECTION CATHODE A CATHODE F COMMON ANODE CATHODE L.DP CATHODE E CATHODE D CATHODE R.DP CATHODE C CATHODE G CATHODE B COMMON ANODEPINS 4, 5, 12: NO CONNECTION FORHDSP-331E/331G/331Y/331A AND NO PIN FOR HDSP-332EHDSP-331E/331G/331Y/331A/332E9Common AnodeCommon Cathode14138761294.12 COMPIN NO.1246789121314CONNECTION ANODE F ANODE G COMMON CATHODEANODE E ANODE D ANODE C ANODE DP COMMON CATHODEANODE B ANODE AHDSP-333E/333G/333Y/333APINS 3, 5, 10, 11: NCCommon Cathode1098524371.6 COMPIN NO.12345678910CONNECTION COMMON CATHODEANODE E ANODE G ANODE F ANODE D COMMON CATHODEANODE DP ANODE C ANODE B ANODE AHDSP-334E/334G/334Y/334APINS 11, 12, 13, 14: NCElectrical/Optical Characteristics at T A = 25˚C High Efficiency Red (HER)Devices HDSP-ParameterSymbol Min.Typ.Max.Units Test Conditions Luminous Intensity/Segment I V 1.15mcd I F = 5 mA 0.81.80mcd I F = 10 mA Forward Voltage V F2.05 2.40V I F = 20 mAPeak Wavelength λPEAK 635nm Dominant Wavelength λd 620nm Reverse VoltageVR5VI R = 100 µAGreen Devices HDSP-ParameterSymbol Min.Typ.Max.Units Test Conditions Luminous Intensity/Segment I V 0.8 2.00mcd I F = 10 mA Forward Voltage V F 2.07V I F = 10 mA 1.802.25 2.60V I F = 20 mAPeak Wavelength λPEAK 568nm Dominant Wavelength λd 573nm Reverse VoltageVR5VI R = 100 µAAbsolute Maximum Ratings at T A = 25˚C DescriptionHERGreenAlGaAs Red Yellow HDSP-33xE HDSP-33xG HDSP-33xA HDSP-33xY Units Power Dissipation Segment 65653052mW Forward Current Segment25[1]25[2]15[3]20[4]mA Peak Forward Current per Segment 1001008080mA (1/10 Duty Factor at 10 kHz)Operating Temperature Range –35 to +85–35 to +85–35 to +85–35 to +85˚C Storage Temperature Range–35 to +85–35 to +85–35 to +85–35 to +85˚C Reverse Voltage per Segment or DP5555V Wave Soldering Temperature for 3 Seconds 250250250250˚C(at 2 mm Distance from the Body)Notes:1.Derate above 25˚C at 0.33 mA/˚C.2.Derate above 25˚C at 0.33 mA/˚C.3.Derate above 25˚C at 0.2 mA/˚C.4.Derate above 25˚C at 0.27 mA/˚C.331G 333G 334G331E 332E 333E 334EYellow Devices HDSP-ParameterSymbol Min.Typ.Max.Units Test Conditions Luminous Intensity/Segment I V 0.71mcd I F = 5 mA 0.801.50mcd I F = 10 mA Forward Voltage V F2.15 2.60V I F = 20 mAPeak Wavelength λPEAK 595nm Dominant Wavelength λd 590nm Reverse VoltageVR5VI R = 100 µAAlGaAs Red Devices HDSP-ParameterSymbol Min.Typ.Max.Units Test Conditions Luminous Intensity/Segment I V 3.93mcd I F = 5 mA 2.0014.20mcd I F = 10 mA Forward Voltage V F 1.85 2.00V I F = 20 mAPeak Wavelength λPEAK 660nm Dominant Wavelength λd 643nm Reverse VoltageVR5VI R= 100 µA331Y 333Y 334Y331A 333A 334AIntensity Bin Limits (mcd at 10 mA)HER/Green/Yellow AlGaAs RedBin Name Min.[1]Max.[1]Min.[1]Max.[1]G 0.801 1.250NA NA H 1.251 2.000NA NA I 2.001 3.200 2.001 3.200J NA NA 3.201 5.050KNA NA5.0518.000Note:1.Tolerance for each bin limit is ± 10%.Color Bin Limits (nm at 10 mA)Dominant Wavelength (nm)Color Bin Min.Max.Note:1.Tolerance for each bin limit is 1 nm.Figure 1. Maximum allowable average or DC current vs. ambient temperature.Figure 2. Forward current vs. forward voltage.Figure 3. Relative luminous intensity vs. DC forward current.High Efficiency Red (HER)Figure 4. Relative efficiency (luminousintensity per unit current) vs. peak current.020*********T A – AMBIENT TEMPERATURE – °C M A X I M U M D C C U R R E N T P E R S E G M E N T – m AV F – FORWARD VOLTAGE – VI F – F O R W A R D C U R R E N T P E R S E G M E N T – m A2.52.01.51.00.50510********IF – FORWARD CURRENT FOR SEGMENT – mAR E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D T O 1 A T 10 m A )35R E L A T I V E EF F I C I E N C Y (N O R M A L I Z E D T O 1 A T 10 m A )1.4005101520253035404550I PEAK – PEAK FORWARD CURRENTPER SEGMENT – mA0.20.40.60.81.01.2Figure 7. Relative luminous intensity vs. DC forward current.Figure 8. Relative efficiency (luminous intensity per unit current) vs. peak current.Figure 5. Maximum allowable average or DC current vs. ambient temperature.Figure 6. Forward current vs. forward voltage.Green30T A – AMBIENT TEMPERATURE – °CM A X I M U M D C C U R R E N T P E R S E G M E N T – m AV F – FORWARD VOLTAGE – VI F – F O R W A R D C U R R E N T P E R S E G M E N T – m A3.02.52.01.51.00.500510********I F – FORWARD CURRENT FOR SEGMENT – mAR E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D T O 1 A T 10 m A )35R E L A T I V E E F F I C I E N C Y (N O R M A L I Z E D T O 1 A T 10 m A )05101520253035404550I PEAK – PEAK FORWARD CURRENTPER SEGMENT – mA0.20.40.60.81.01.2Figure 9. Maximum allowable average or DC current vs. ambient temperature.Figure 10. Forward current vs. forward voltage.Figure 11. Relative luminous intensity vs. DC forward current.Figure 12. Relative efficiency (luminous intensity per unit current) vs. peak current.AlGaAs RedT A – AMBIENT TEMPERATURE – °C M A X I M U M D C C U R R E N T P E R S E G M E N T – m AV F – FORWARD VOLTAGE – VI F – F O R W A R D C U R R E N T P E R S E G M E N T – m A3.02.52.01.51.00.500510********I F – FORWARD CURRENT FOR SEGMENT – mAR E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D T O 1 A T 10 m A )35R E L A T I V E E F F I C I E N C Y (N O R M A L I Z E D T O 1 A T 10 m A )05101520253035404550I PEAK – PEAK FORWARD CURRENTPER SEGMENT – mA0.20.40.60.81.01.2Figure 13. Maximum allowable average or DC current vs. ambient temperature.Figure 14. Forward current vs. forward voltage.Figure 15. Relative luminous intensity vs. DC forward current.Figure 16. Relative efficiency (luminous intensity per unit current) vs. peak current.YellowT A – AMBIENT TEMPERATURE – °C M A X I M U M D C C U R R E N T P E R S E G M E N T – m AV F – FORWARD VOLTAGE – VI F – F O R W A R D C U R R E N T P E R S E G M E N T – m A3.52.52.01.51.00.50051015202530I F – FORWARD CURRENT FOR SEGMENT – mAR E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D T O 1 A T 10 m A )353.0R E L A T I V E E F F I C I E N C Y (N O R M A L I Z E D T O 1 A T 10 m A )1.4005101520253035404550I PEAK – PEAK FORWARD CURRENTPER SEGMENT – mA0.20.40.60.81.01.2/semicon-ductorsFor product information and a complete list of distributors, please go to our web site. For technical assistance call:Americas/Canada: +1 (800) 235-0312 or (916) 788-6763Europe: +49 (0) 6441 92460China: 10800 650 0017Hong Kong: (+65) 6756 2394India, Australia, New Zealand: (+65) 6755 1939Japan: (+81 3) 3335-8152(Domestic/ International), or 0120-61-1280(Domestic Only)Korea: (+65) 6755 1989Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843Data subject to change.Obsoletes 5988-2971ENJuly 17, 20045988-9421EN。

5082-563G-0K300资料

DescriptionThese slim font seven segment displays incorporate a new slim font character design. This slim font features narrow width,specially mitered segments to give a fuller appearance to the illuminated character. Faces of these displays are painted aneutral gray for enhanced on/off contrast.Agilent HDSP-301x/303x Series HDSP-561x/563x Series 10 mm and 13 mm Slim Font Seven Segment DisplaysData SheetFeatures•Excellent appearance •Slim font design •Mitered corners, evenly illuminated segments•Gray face for optimum on/off contrast •Choice of colors: HER, green,yellow, and AlGaAs •Choice of character size: 10 mm and 13 mm •Characterized for luminous intensityDevices HER Green Yellow AlGaAs HDSP-HDSP-HDSP-HDSP-Description301E 301G 301Y 301A Common Anode, 10 mm Display 303E 303G 303Y 303A Common Cathode, 10 mm Display 561E 561G 561Y 561A Common Anode, 13 mm Display 563E563G563Y563ACommon Cathode, 13 mm DisplayAll devices are available in either common anode or commoncathode configuration with righthand decimal point.Part Numbering System5082- x xx x-x x x xxHDSP- x xx x-x x x xxMechanical Options[1]00: No Mechanical OptionColor Bin Options[1,2]0: No Color Bin LimitationMaximum Intensity Bin[1,2]0: No Maximum Intensity Bin LimitationMinimum Intensity Bin[1,2]0: No Minimum Intensity Bin LimitationDevice Configuration/Color[1]A: AlGaAs RedE: High Efficiency RedG: GreenY: YellowDevice Specific Configuration[1]Refer to Respective Data SheetPackage[1]Refer to Respective Data SheetNotes:1. For codes not listed in the figure above, please refer to the respective data sheet or contact your nearest Agilent representativefor details.2. Bin options refer to shippable bins for a part-number. Color and Intensity Binbs are typically restricted to 1 bin per tube(exceptions may apply). Please refer to respective data sheet for specific bin limit information.Pin Function1G2F3Common A/C 4E5D6DP7C8Common A/C 9B10A7.006.40NOTE: QDSP-399G DOES NOT HAVE PIN 6.COUNTRY TOP SIDEFRONT VIEW RIGHT SIDE0.30 ± 0.05(0.012)6.001.85Pin Function 1E 2D3Common A/C 4C 5DP 6B 7A8Common A/C 9F 10G0.29 ± 0.08 TYP.(0.011)12345(0.023)(0.141)(0.100)NOTES:1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).2. UNLESS OTHERWISE STATED, TOLERANCES ARE ±0.25 mm.Absolute Maximum RatingsDescription HER Green Yellow AlGaAs Units Average Power per Segment or DP10510510537mW Peak Forward Current per Segment or DP90909045mA DC Forward Current per Segment or DP30303015mA Operating Temperature Range–40 to +80–40 to +80–40 to +80–20 to +80˚C Storage Temperature Range–40 to +80–40 to +80–40 to +80–40 to +80˚C Reverse Voltage per Segment or DP5555V Wavesoldering Temperature for 3 Seconds250250250250˚C 1.59 mm below bodyNotes:1.Derate above 33˚C at 0.34 mA/˚C for HER.2.Derate above 27˚C at 0.32 mA/˚C for Green.3.Derate above 30˚C at 0.33 mA/˚C for Yellow.4.Derate above 60˚C at 0.25 mA/˚C for AlGaAs.Electrical/Optical Characteristics at T A = 25˚CHERDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 301/303E Luminous Intensity/Segment I V 1.251 2.000mcd I F = 10 mA (Digit Average)Forward Voltage/Segment V F 1.90 2.50V I F = 20 mAor DPPeak WavelengthλPEAK635nm I F = 20 mADominant Wavelengthλd625nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinHERDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 561/563E Luminous Intensity/Segment I V 2.001 3.526mcd I F = 10 mA (Digit Average)Forward Voltage/Segment V F 1.90 2.50V I F = 20 mAor DPPeak WavelengthλPEAK635nm I F = 20 mADominant Wavelengthλd625nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 301/303G Luminous Intensity/Segment I V 2.001 3.200mcd I F = 10 mA (digit average)Forward Voltage/Segment V F 2.25 2.50V I F = 20 mAor DPPeak WavelengthλPEAK568nm I F = 20 mADominant Wavelengthλd573nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinGreenDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 561/563G Luminous Intensity/Segment I V 3.201 5.601mcd I F = 10 mA (Digit Average)Forward Voltage/Segment V F 2.25 2.50V I F = 20 mAor DPPeak WavelengthλPEAK568nm I F = 20 mADominant Wavelengthλd573nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinYellowDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 301/303Y Luminous Intensity/Segment I V 1.251 2.000mcd I F = 10 mA (Digit Average)Forward Voltage/Segment V F 2.15 2.50V I F = 20 mAor DPPeak WavelengthλPEAK589nm I F = 20 mADominant Wavelengthλd590nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 561/563Y Luminous Intensity/Segment I V 2.00 3.526mcd I F = 10 mA (Digit Average)Forward Voltage/Segment V F 2.15 2.50V I F = 20 mAor DPPeak WavelengthλPEAK589nm I F = 20 mADominant Wavelengthλd590nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinNotes:1.Typical specification for reference only. Do not exceed absolute maximum ratings.2.The dominant wavelength, λ, is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device.AlGaAsDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 301/303A Luminous Intensity/Segment I V0.3200.505mcd I F = 1 mA (Digit Average)Forward Voltage/Segment V F 1.80 2.20V I F = 20 mAor DPPeak WavelengthλPEAK660nm I F = 20 mADominant Wavelengthλd643nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinAlGaAsDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions 561/563A Luminous Intensity/Segment I V0.5060.878mcd I F = 1 mA (Digit Average)Forward Voltage/Segment V F 1.80 2.20V I F = 20 mAor DPPeak WavelengthλPEAK660nm I F = 20 mADominant Wavelengthλd643nm I F = 20 mAReverse Current I R100µA V R = 5 VThermal Resistance LED RθJ–PIN351.5˚C/W/Seg.Junction-to-PinNotes:1.Typical specification for reference only. Do not exceed absolute maximum ratings.2.The dominant wavelength, λ, is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device.HDSP-301E/303E/561E/563EIV Bin Category Min.Max.I 1.100 2.200K 1.800 3.600HDSP-561Y/563Y IV Bin Category Min.Max.K 1.800 3.600L 2.8005.600HDSP-301Y/303YIV Bin Category Min.Max.I 1.100 2.200K 1.8003.600HDSP-301A/303A/561A/563AIV Bin Category Min.Max.F 0.2800.560G 0.4500.900HDSP-301G/303G/561G/563GIV Bin Category Min.Max.K 1.800 3.600L 2.800 5.600Intensity Bin Limits (mcd)GreenYellowHERAlGaAs RedDominant Wavelength (nm)ColorBin Min.Max.Green 3570.00574.504567.00571.50Yellow2586.50590.003584.00587.50Color CategoriesNote:1. All categories are established for classification of products.Products may not be available in all categories. Please contact your Agilent representatives for further clarification/information.YellowFigure 1. Maximum allowable DC current vs.ambient temperature.Figure 2. Forward current vs. forward voltage.Figure 3. Relative luminous intensity vs. DC forward current.HDSP-301x/303x SeriesContrast EnhancementFor information on contrast enhancement, please see Application Note 1015.Soldering/CleaningCleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from thechlorinated hydrocarbon family (methylene chloride,Figure 4. Maximum allowable DC current vs.ambient temperature.Figure 5. Forward current vs. forward voltage.Figure 6. Relative luminous intensity vs. DC forward current.HDSP-561x/563x SeriesI D C – M A X I M U M D C C U R R E N T P E R S E G M E N T – m AT A – AMBIENT TEMPERATURE – °CI F – F O R W A R D C U R R E N TP E R S E G M E N T – m AV F – FORWARD VOLTAGE – V I D C – M A X I M U M D C C U R R E N T P E R S E G M E N T – m AT A – AMBIENT TEMPERATURE – °CI F – F O R W A R D C U R R E N TP E R S E G M E N T – m AV F – FORWARD VOLTAGE – V trichloroethylene, carbon tetrachloride, etc.) are notrecommended for cleaning LED parts. All of these varioussolvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts.For information on soldering LEDs, please refer to Application Note 1027.R E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D T O 1 A T 5 m A F O R H E R A N D Y E L L O W A N D T O 1 A T 10 m A F O R G R E E N )I F – DC FORWARD CURRENT – mA12682410R E L A T I V E L U M I N O U S I N T E N S I T Y (N O R M A L I Z E D T O 1 A T 5 m A F O R H E R A N D Y E L L O W A N D T O 1 A T 10 m A F O R G R E E N )I F – DC FORWARD CURRENT – mA/semiconduc-torsFor product information and a complete list of distributors, please go to our web site.For technical assistance call:Americas/Canada: +1 (800) 235-0312 or (916) 788-6763Europe: +49 (0) 6441 92460China: 10800 650 0017Hong Kong: (+65) 6756 2394India, Australia, New Zealand: (+65) 6755 1939 Japan: (+81 3) 3335-8152(Domestic/ International), or 0120-61-1280(Domestic Only) Korea: (+65) 6755 1989Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843Data subject to change.Obsoletes 5980-2919ENJuly 11, 20045988-4352EN。

麦康凯琼脂培养基产品说明书

化学品安全技术说明书第一部分化学品及企业标识产品中文名称：麦康凯琼脂培养基产品英文名称：MacConkey Agar产品编号：022143企业名称：广东环凯微生物科技有限公司地址：广东省广州市黄埔区广州开发区科学城神舟路788号邮编：510663公司网址电子邮件地址：*********************传真号码：************销售热线：************-8602技术热线：************-8877/8876推荐用途和限制用途：生化研究/分析第二部分危险性概述GSH危害性类别非危险物质或混合物GSH标签要素非危险物质或混合物其它危害（健康危害、环境危害）未见报道第三部分成分/组成信息混合物化学品成分：参考培养基使用说明。

有害物质成分：无第四部分急救措施一般信息：无特殊的措施要求。

皮肤接触：立即用清水彻底清洗。

眼睛接触：立即提起眼睑，用大量流动清水冲洗15min。

如不适就医。

吸入：如果吸入，将人员移动到新鲜空气处，如果没有呼吸，进行人工呼吸操作，并联系医生。

食入：如误食，用水冲洗口腔，如不适就医。

就医信息：出示产品使用说明或者此SDS。

第五部分消防措施危险特性：不助燃。

有害燃烧产物：一氧化碳，二氧化碳，氮的氧化物。

灭火方法及灭火剂：选用适合周围火源的灭火器。

水，泡沫，二氧化碳，沙土。

灭火注意事项：防止气体吸入。

第六部分泄露应急处理个人防护：穿个人实验服,佩戴手套和口罩,避免吸入干粉。

环境保护措施：用湿布和地拖擦拭干净。

清洁/收集措施：保持干燥。

迅速清洗弄脏的区域。

第七部分操作处置与储存安全操作注意事项：防止粉尘扬起，应提供通风设备。

储存注意事项：贮存于避光、干燥处，用后立即旋紧瓶盖。

第八部分接触控制/个人防护职业接触限值没有已知的国家规定的暴露极限。

工程控制：提供安全淋浴和洗眼设备个人保护措施呼吸系统防护：在通风橱里称取产品，佩戴口罩。

眼睛防护：佩戴安全眼镜。

身体防护：穿实验室服。

5082-0012资料

DescriptionThis PIN diode chip is silicon dioxide or nitride passi-vated. The 5082-0012 has a planar construction. The fabrication processes are optimized for long term reliability and tightly controlled for uniformity in electrical performance.OutlineMaximum RatingsJunction Operating and StorageTemperature Range .............................-65°C to +150°C Soldering Temperature ..........+425°C for 1 min. max.5082-0012PIN Diode Chip for Hybrid MIC Switches/AttenuatorsData SheetFeatures•Low Series Resistance: 1.0Ω TypicalApplicationsThis general purpose PIN diode is intended for low power switching applications such as duplexers,antenna switching matrices, digital phase shifters, time multiplex filters, TR switches, pulse and amplitude modulators, limiters, leveling circuits, and attenuators.Electrical Specifications at T A = 25°CTypical ParametersNearest Typical Chip Equivalent Minimum Maximum Typical Reverse Part Packaged Breakdown Junction Series Typical Recovery Number Part No.VoltageCapacitance Resistance Lifetime Time 5082-5082-V BR (V)C j (pF)R S (Ω)τ (ns)t rr (ns)001230011500.12 1.0400100 Test V R = V BR V R = 50 V I F = 100 mA I F = 50 mA I F = 20 mA ConditionsMeasure f = 1 MHzf = 100 MHzI R = 250 mAV R = 10 V I R ≤ 10 mA90% RecoveryDimensions in millimeters (1/1000 inch)Assembly and Handling Procedures forPIN Chips1. StorageDevices should be stored in a dry nitrogen purged dessicator or equivalent.2. CleaningIf required, surface contamination may be removed with electronic grade solvents. Typical solvents, such as freon (T.F. or T.M.C.), acetone, deionized water, and methanol, or their locally approved equivalents, can be used singularly or in combinations. Typical cleaning times per solvent are one to three minutes. DI water and methanol should be used (in that order) in the final cleans. Final drying can be accomplished by placing the cleaned dice on clean filter paper and drying with an infrared lamp for 5-10 minutes. Acids such as hydrofluoric (HF), nitric (HN O3) and hydrochloric (HCl) should not be used.The effects of cleaning methods/solutions should be verified on small samples prior to submitting the entire lot.Following cleaning, dice should be either used in assembly (typically within a few hours) or stored in clean containers in a reducing atmosphere or a vacu-um chamber.3. Die Attacha. EutecticAuSn preform with stage temperature of 310°C for one minute max. AuGe preform with stage temperature of 390°C for one minute max.b. EpoxyFor epoxy die-attach, conductive silver-filled or gold-filled epoxies are recommended. This method can be used for all Avago PIN chips.4. Wire BondingEither ultrasonic or thermocompression bonding tech-niques can be employed. Suggested wire is pure gold, 0.7 to 1.5 mil diameter.For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries.Data subject to change. Copyright © 2006 Avago Technologies Pte. All rights reserved. Obsoletes 5965-8880E5989-4778EN February 23, 2006。

UCONTMLubricant75-H-90,000

UCON TM Lubricant 75-H-90,000 is a polyalkylene glycol (PAG) containing 75 weight percent oxyethylene and 25 percent oxypropylene groups. It is water soluble below 75ºC and has two terminal hydroxyl groups. UCON TM Lubricant 75-H-90,000 offers exceptional lubricity and cleanliness into many lubricant applications, including textile fiber lubricant, water glycol hydraulic fluid and metal working fluids.Applications of UCON TM Lubricant 75-H-90,000As a Lubricant:-Metal Working Fluid-Textile Lubricant-Hydraulic Fluid Thickener-Mandrel Release AgentSpecialty:-Electronic Chemicals-Quenching Component-Chemical IntermediateFor ease in transport and handling UCON TM Lubricant 75-H-90,000 is available in three versions: •as neat, undiluted polyol: UCON TM Lubricant 75-H-90,000•as 30% water content dilution: UCON TM Lubricant 75-H-90,000 AQ•as 40% water content dilution: UCON TM Lubricant 75-H-90,000 40%AQProperties* of UCON TM Lubrcant 75-H-90,000 ; 75-H-90,000 AQ and 75-H-90,000 40%AQProperties 75-H-90,000 75-H-90,000 AQ 75-H-90,000 40%AQ Water Content, wt% 0.30 max. 28 - 32 39 - 41 Viscosity, cSt at 40ºC 17,000 2,410 1,140 Viscosity, cSt at 100ºC 2545 n.a. n.a. Viscosity Index (VI) ASTM D2270, IP226 414 n.a. n.a. Specific Gravity, 20ºC 1.092 1.090 1.090 Specific Gravity, 40ºC 1.074 1.071 1.069 Color, Gardner 4 max. 2 max. 2 max Alkalinity, wt% 0.10 max n.a. n.a.Pour Point, ºC, ASTM D 97 4.4 < 0 < 0 Cloud Point , ºC, 10 % aqueous 72 - 77 n.a. n.a. Flash Point, Open Cup, ºC, ASTM D92 265 None None* Typical properties, not to be construed as specificationsUCON™ Lubricant 75-H-280,000 is an extremely viscous, high molecular weight, water soluble polyalkylene glycol (PAG) polymer containing 75 weight percent oxyethylene and 25 weight percent oxypropylene groups.UCON™ Lubricant 75-H-280,000 is chemical and shear stable, is non-foaming and offers good lubricity properties.UCON TM Lubricant 75-H-280,000 can be used as a thickener in fire resistant water-glycol hydraulicfluids. Base stock can be formulated with water and ethylene glycol, diethylene glycol or propyleneglycol. Anti-corrosion and anti-wear additives are used to enhance lubricating characteristics.UCON TM Lubricant 75-H-280,000 can also be used as base oil in applications such as heat treating and quenching, metalworking and aqueous thickening.Typical ISO 46 HF-C formulation:Component Wt%Water 38-42Glycol 36-40UCON TM Lubricant 75-H-280,000: 18-22Additives / inhibitors 3For ease in transport and handling UCON TM Lubricant 75-H-280,000 is available as 40% water contentdilution: UCON TM Lubricant 75-H-280,000 40%AQProperties* of UCON™ Lubricant 75-H-280,000 and 75-H-280,000 40%AQ40%AQ75-H-280,000 Properties 75-H-280,000Water Content, wt% 0.30 max. 39 - 41Viscosity, cSt at 40ºC 55,000 2.600Viscosity, cSt at 100ºC 7900 n.a.Viscosity Index (VI) ASTM D2270, IP226 430 n.a.Specific Gravity, 20ºC 1.094 1.090Specific Gravity, 40ºC 1.074 1.069Color, Gardner 4 max. 3 max.Alkalinity, wt% 0.10 max n.a.Pour Point, ºC, ASTM D 97 8 < 0Cloud Point , ºC, 10 % aqueous 72 - 78 n.a.Flash Point, Open Cup, ºC, ASTM D92 240 None* Typical properties, not to be construed as specification. Sales specifications are available on request.UCON TM Lubricant 75-H-380,000UCONTM™ Lubricant 75-H-380,000 is an extremely viscous, high molecular weight, water soluble polyalkylene glycol (PAG) polymer containing 75 weight percent oxyethylene and 25 weight percent oxypropylene groups.UCON TM Lubricant 75-H-380,000 is chemical and shear stable, is non-foaming and offers good lubricity properties.UCON TM Lubricant 75-H-380,000 can be used as a thickener in fire resistant water-glycol hydraulic fluids. Base stock can be formulated with water and ethylene glycol, diethylene glycol or propylene glycol. Anti-corrosion and anti-wear additives are used to enhance lubricating characteristics.UCON TM Lubricant 75-H-280,000 can also be used as base oil in applications such as heat treating and quenching, metalworking and aqueous thickening.Typical ISO 46 HF-C formulation: Component Wt% Glycol 44-46 Water 38-42 Thickener 11-13Additives / inhibitors 3For ease in transport and handling UCON TM Lubricant 75-H-380,000 is available in three water dilutions:• as 20% water content dilution: UCON TM Lubricant 75-H-380,000 20%AQ • as 30% water content dilution: UCON TM Lubricant 75-H-380,000 AQ • as 40% water content dilution: UCON TM Lubricant 75-H-380,000 40%AQProperties* of UCON™ Lubricant 75-H-380,000 and 75-H-380,000 40%AQProperties 75-H-380,000 75-H-380,000 20%AQ 75-H-380,000 AQ 75-H-380,00040%AQWater Content, wt% 0.30 max. 18.5 – 21.5 28 - 32 39 - 41 Viscosity, cSt at 40ºC 100,000 22,000 8,800 4,000 Viscosity, cSt at 100ºC11,175 n.a. n.a. n.a. Viscosity Index (VI) ASTM D2270, IP226 450 n.a. n.a. n.a. Specific Gravity, 20ºC 1.098 1.094 1.092 1.090 Specific Gravity, 40ºC 1.076 1.073 1.071 1.069 Color, Gardner 4 max 4 max. 4 max. 4 max Alkalinity, wt%0.10 max n.a. n.a. n.a. Pour Point, ºC, ASTM D 97 16 < 0 < 0 < 0 Cloud Point , ºC, 10 % aqueous 73 - 79 n.a. n.a. n.a. Flash Point, Open Cup, ºC, ASTM D92260NoneNoneNone* Typical properties, not to be construed as specification. Sales specifications are available on request.Technical Data Sheet Overview of all commercial grades75-H-90,000 75-H-90,000AQ 75-H-90,00040% AQ75-H-280,00040% AQ75-H-380,00020% AQ75-H-380,000AQ75-H-380,00040% AQWaterContent,wt% 0.3 30 40 40 20 30 40 Viscosity, cSt at 40ºC 17,000 2,410 1,140 2,600 22,000 8,800 4,000 Specific Gravity, 20ºC 1.092 1.090 1.090 1.090 1.094 1.092 1.090 Specific Gravity, 40ºC 1.074 1.071 1.069 1.069 1.073 1.071 1.069 Color, Gardner 4 max 2 max 2 max 3 max 4 max 4 max 4 maxPour Point, ºC, ASTM D 97 4.4 < 0 < 0 < 0 < 0 < 0 < 0TM Trademark of the Dow Chemical Company 4。

5082-K123-CG000资料

Features• Low Power Consumption • Industry Standard Size• Industry Standard Pinout • Choice of Character Size7.6 mm (0.30 in), 10 mm (0.40 in), 10.9 mm (0.43 in), 14.2 mm (0.56 in), 20 mm (0.80 in)• Choice of ColorsAlGaAs Red, High Efficiency Red (HER), Yellow, Green• Excellent Appearance Evenly Lighted Segments±50° Viewing Angle• Design FlexibilityCommon Anode or Common CathodeSingle and Dual DigitLeft and Right Hand Decimal Points±1. Overflow Character• Categorized for Luminous IntensityYellow and Green Categorized for ColorUse of Like Categories Yields a Uniform Display• Excellent for Long Digit String Multiplexing DescriptionThese low current seven segment displays are designed for applica-tions requiring low power consumption. They are tested and selected for their excellent low current characteristics to ensure that the segments are matched at low currents. Drive currents as low as 1 mA per segment are available.Pin for pin equivalent displays are also available in a standard current or high light ambient design. The standard current displays are available in all colors and are ideal for most applica-tions. The high light ambient displays are ideal for sunlight ambients or long string lengths. For additional information see the 7.6 mm Micro Bright Seven Segment Displays, 10 mm Seven Segment Displays, 7.6 mm/10.9 mm Seven Segment Displays, 14.2 mm Seven Segment Displays, 20 mm Seven Segment Displays, or High Light Ambient Seven Segment Displays data sheets.Low Current Seven SegmentDisplays Technical Data HDSP-335x SeriesHDSP-555x SeriesHDSP-751x SeriesHDSP-A10x Series HDSP-A80x Series HDSP-A90x Series HDSP-E10x Series HDSP-F10x Series HDSP-G10x Series HDSP-H10x Series HDSP-K12x, K70x Series HDSP-N10x SeriesHDSP-N40x SeriesDevicesAlGaAs HER Yellow Green Package HDSP-HDSP-HDSP-HDSP-Description Drawing A1017511A801A9017.6 mm Common Anode Right Hand Decimal A A1037513A803A9037.6 mm Common Cathode Right Hand Decimal B A1077517A807A9077.6 mm Common Anode ±1. Overflow C A1087518A808A9087.6 mm Common Cathode ±1. Overflow D F10110 mm Common Anode Right Hand Decimal E F10310 mm Common Cathode Right Hand Decimal F F10710 mm Common Anode ±1. Overflow G F10810 mm Common Cathode ±1. Overflow H G10110 mm Two Digit Common Anode Right Hand Decimal X G10310 mm Two Digit Common Cathode Right Hand Decimal Y E100335010.9 mm Common Anode Left Hand Decimal I E101335110.9 mm Common Anode Right Hand Decimal J E103335310.9 mm Common Cathode Right Hand Decimal K E106335610.9 mm Universal ±1. Overflow[1]L H101555114.2 mm Common Anode Right Hand Decimal M H103555314.2 mm Common Cathode Right Hand Decimal N H107555714.2 mm Common Anode ±1. Overflow O H108555814.2 mm Common Cathode ±1. Overflow P K121K70114.2 mm Two Digit Common Anode Right Hand Decimal R K123K70314.2 mm Two Digit Common Cathode Right Hand Decimal S N10020 mm Common Anode Left Hand Decimal Q N101N40120 mm Common Anode Right Hand Decimal T N103N40320 mm Common Cathode Right Hand Decimal U N10520 mm Common Cathode Left Hand Decimal V N106N40620 mm Universal ±1. Overflow[1]W Note:1. Universal pinout brings the anode and cathode of each segment’s LED out to separate pins. See internal diagrams L or W.Part Numbering System5082-x xx x-x x x xxHDSP-x xx x-x x x xxMechanical Options[1]00: No mechanical optionColor Bin Options[1,2]0: No color bin limitationMaximum Intensity Bin[1,2]0: No maximum intensity bin limitationMinimum Intensity Bin[1,2]0: No minimum intensity bin limitationDevice Configuration/Color[1]G: GreenDevice Specific Configuration[1]Refer to respective datasheetPackage[1]Refer to Respective datasheetNotes:1. For codes not listed in the figure above, please refer to the respective datasheet or contact your nearest Agilent representative fordetails.2. Bin options refer to shippable bins for a part-number. Color and Intensity Bins are typically restricted to 1 bin per tube (excep-tions may apply). Please refer to respective datasheet for specific bin limit information.Package DimensionsPackage Dimensions (cont.)Package Dimensions (cont.)*The Side View of package indicates Country of Origin.Package Dimensions (cont.)Package Dimensions (cont.)Package Dimensions (cont.)Internal Circuit DiagramInternal Circuit Diagram (cont.)Absolute Maximum RatingsAlGaAs Red - HDSP-HERA10X/E10X/H10X HDSP-751X/Yellow GreenK12X/N10X/N40X335X/555X/HDSP-A80X HDSP-A90X Description F10X, G10X Series K70X Series Series Series Units Average Power per Segment or DP375264mW Peak Forward Current per 45mA Segment or DPDC Forward Current per15[1]15[2]mA Segment or DPOperating Temperature Range-20 to +100-40 to +100°C Storage Temperature Range -55 to +100°C Reverse Voltage per Segment 3.0V or DPWave Soldering Temperature for 3Seconds (1.60 mm [0.063 in.] below 250°C seating body)Notes:1. Derate above 91°C at 0.53 mA/°C.2. Derate HER/Yellow above 80°C at 0.38 mA/°C and Green above 71°C at 0.31 mA/°C.Electrical/Optical Characteristics at T A = 25°CAlGaAs RedDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions315600I F = 1 mA A10x3600I F = 5 mA330650I F = 1 mAF10x, G10x3900I F = 5 mA390650I F = 1 mA E10x Luminous Intensity/Segment[1,2]I Vµcd(Digit Average)3900I F = 5 mA400700I F = 1 mAH10x, K12x4200I F = 5 mA270590I F = 1 mAN10x, N40x3500I F = 5 mA1.6I F = 1 mAForward Voltage/Segment or DP V F 1.7V I F = 5 mA1.82.2I F = 20 mA PkAll Devices Peak WavelengthλPEAK645nmDominant Wavelength[3]λd637nmReverse Voltage/Segment or DP[4]V R 3.015V I R = 100 µATemperature Coefficient of∆V F/°C-2 mV mV/°CV F/Segment or DPA10x255F10x, G10x320E10x340Thermal Resistance LED RθJ-PIN°C/W/SegH10x, K12x Junction-to-Pin400N10x, N40x430High Efficiency RedDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions160270I F = 2 mA 751x1050I F = 5 mA200300I F = 2 mA Luminous Intensity/Segment[1,2]I V mcd(Digit Average)1200I F = 5 mA335x, 555x,K70x270370I F = 2 mA1480I F = 5 mA1.6I F = 2 mAForward Voltage/Segment or DP V F 1.7V I F = 5 mA2.1 2.5I F = 20 mA Pk All Devices Peak WavelengthλPEAK635nmDominant Wavelength[3]λd626nmReverse Voltage/Segment or DP[4]V R 3.030V I R = 100 µATemperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DP751x200335x Thermal Resistance LED RθJ-PIN280°C/WJunction-to-Pin555x, K70x345YellowDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions Luminous Intensity/Segment[1,2]250420I F = 4 mA(Digit Average)I V mcd1300I F = 10 mA1.7I F = 4 mAForward Voltage/Segment or DP V F 1.8V I F = 5 mA A80x2.1 2.5I F = 20 mA PkPeak WavelengthλPEAK583nmDominant Wavelength[3,5]λd581.5585592.5nmReverse Voltage/Segment or DP[4]V R 3.030V I R = 100 µATemperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DPThermal Resistance LED RθJ-PIN200°C/WJunction-to-PinGreenDeviceSeriesHDSP-Parameter Symbol Min.Typ.Max.Units Test Conditions Luminous Intensity/Segment[1,2]250475I F = 4 mA(Digit Average)I V mcd1500I F = 10 mA1.9I F = 4 mAForward Voltage/Segment or DP V F 2.0V I F = 10 mA A90x2.1 2.5I F = 20 mA PkPeak WavelengthλPEAK566nmDominant Wavelength[3,5]λd571577nmReverse Voltage/Segment or DP[4]V R 3.030V I R = 100 µATemperature Coefficient of∆V F/°C-2mV/°CV F/Segment or DPThermal Resistance LED RθJ-PIN200°C/WJunction-to-PinNotes:1. Device case temperature is 25°C prior to the intensity measurement.2. The digits are categorized for luminous intensity. The intensity category is designated by a letter on the side of the package.3. The dominant wavelength, λd, is derived from the CIE chromaticity diagram and is the single wavelength which defines the color of thedevice.4. Typical specification for reference only. Do not exceed absolute maximum ratings.5. The yellow (HDSP-A800) and Green (HDSP-A900) displays are categorized for dominant wavelength. The category is designated by anumber adjacent to the luminous intensity category letter.AlGaAs RedIntensity Bin Limits (mcd)AlGaAs RedHDSP-A10xIV Bin Category Min.Max.E0.3150.520F0.4280.759G0.621 1.16H0.945 1.71I 1.40 2.56J 2.10 3.84K 3.14 5.75L 4.708.55HDSP-E10x/F10x/G10xIV Bin Category Min.Max.D0.3910.650E0.5320.923F0.755 1.39G 1.13 2.08H 1.70 3.14HDSP-H10x/K12xIV Bin Category Min.Max.C0.4150.690D0.5650.990E0.810 1.50F 1.20 2.20G 1.80 3.30H 2.73 5.00I 4.097.50HDSP-N10xIV Bin Category Min.Max.A0.2700.400B0.3250.500C0.4150.690D0.5650.990E0.810 1.50F 1.20 2.20G 1.80 3.30H 2.73 5.00I 4.097.50Intensity Bin Limits (mcd), continued HERHDSP-751xIV Bin Category Min.Max.B0.1600.240C0.2000.300D0.2500.385E0.3150.520F0.4280.759G0.621 1.16HDSP-751xIV Bin Category Min.Max.B0.2400.366C0.3000.477D0.3910.650E0.5320.923F0.755 1.39G 1.13 2.08H 1.70 3.14HDSP-555x/K70xIV Bin Category Min.Max.A0.2700.400B0.3250.500C0.4150.690D0.5650.990E0.810 1.50F 1.20 2.20G 1.80 3.30H 2.73 5.00I 4.097.50Intensity Bin Limits (mcd), continued YellowHDSP-A80xIV Bin Category Min.Max.D0.2500.385E0.3150.520F0.4250.760G0.625 1.14H0.940 1.70I 1.40 2.56J 2.10 3.84K 3.14 5.76L 4.718.64M7.0713.00N10.6019.40O15.9029.20P23.9043.80Q35.8065.60GreenHDSP-A90xIV Bin Category Min.Max.E0.3150.520F0.4250.760G0.625 1.14H0.940 1.70I 1.40 2.56J 2.10 3.84K 3.14 5.76L 4.718.64M7.0713.00N10.6019.40O15.9029.20P23.9043.80Q35.8065.60Electrical/OpticalFor more information on electrical/optical characteristics, please see Application Note 1005.Contrast Enhancement For information on contrast enhancement, please see Application Note 1015.Soldering/Cleaning Cleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from the chorinated hydrocarbon family (methylene chloride, trichloro-ethylene, carbon tetrachloride, etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts.For information on soldering LEDs, please refer to Application Note 1027.Note:All categories are established for classification of products. Productsmay not be available in all categories. Please contact your localAgilent representatives for further clarification/information.Color Categories/semiconductorsFor product information and a complete list ofdistributors, please go to our web site.For technical assistance call:Americas/Canada: +1 (800) 235-0312 or(916) 788 6763Europe: +49 (0) 6441 92460China: 10800 650 0017Hong Kong: (+65) 6271 2451India, Australia, New Zealand: (+65) 6271 2394Japan: (+81 3) 3335-8152(Domestic/International), or0120-61-1280(Domestic Only)Korea: (+65) 6271 2194Malaysia, Singapore: (+65) 6271 2054Taiwan: (+65) 6271 2654Data subject to change.Copyright © 2005 Agilent Technologies, Inc.Obsoletes 5988-8412ENJanuary 19, 20055989-0080EN。